®
PORTABLE
FORCED
AIR HEATERS
OWNER’S MANUAL
REMJ70
REMJ150
150 SIDE HANDLE
PFA/PV 005
IMPORTANT
Read and understand this manual before assembling, starting or servicing
heater. Improper use of heater can cause serious injury. Keep this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS (Continued)
SAFETY
• Useonlykerosenetoavoidriskoffireorexplosion. Neverusegasoline, naphtha, paint
thinners, alcohol, or other highly flammable fuels.
INFORMATION
Continued
• Fueling
a) Personnel involved with fueling shall be qualified and thoroughly familiar with
the manufacturer's instructions and applicable federal, state, and local regula-
tions regarding the safe fueling of heating units.
b) Only the type of fuel specified on the heater's data plate shall be used.
c) All flame, including the pilot light, if any, shall be extinguished and the heater
allowed to cool, prior to fueling.
d) During fueling, all fuel lines and fuel-line connections shall be inspected for leaks.
Any leaks shall be repaired prior to returning the heater to service.
e) At no time shall more than one day's supply of heater fuel be stored inside a
building in the vicinity of the heater. Bulk fuel storage shall be outside the struc-
ture.
f) All fuel storage shall be located a minimum of 25 feet (762 cm) from heaters,
torches, welding equipment, and similar sources of ignition (exception: the fuel
reservoir integral with the heater unit).
g) Whenever possible, fuel storage shall be confined to areas where floor penetra-
tions do not permit fuel to drip onto or be ignited by a fire at lower elevation.
h) Fuel storage shall be in accordance with the authority having jurisdiction.
• Never use heater where gasoline, paint thinner, or other highly flammable vapors are
present.
• Follow all ordinances and codes when using heater.
• Heaters used in the vicinity of tarpaulins, canvas, or similar enclosure materials
shall be located a safe distance from such materials. The recommended mini-
mum safe distance is 10 feet (305 cm). It is further recommended that these
enclosure materials be of a fire retardant nature. These enclosure materials shall
be securely fastened to prevent them from igniting or from upsetting the heater
due to wind action.
• Use only in well-vented areas. Before using heater, provide at least a three-square-
foot opening of fresh, outside air for each 100,000 Btu/Hr of rating.
• Use only in places free of flammable vapors or high dust content.
• Use only the electrical voltage and frequency specified on model plate.
• Use only a grounded extension cord.
• Minimum heater clearances from combustibles:
Outlet: 8 Ft. (250 cm) Sides,Top, and Rear: 4 Ft. (125 cm)
• Locate heater on a stable and level surface if heater is hot or running or a fire may
occur.
• When moving or storing heater, keep heater in a level position or fuel spillage may
occur.
• Keep children and animals away from heater.
• Unplug heater when not in use.
• When used with thermostat, heater may start anytime.
• Never use heater in living or sleeping areas.
• Never block air inlet (rear) or air outlet (front) of heater.
• Never move, handle, refuel, or service a hot, operating, or plugged-in heater.
• Never attach duct work to front or rear of heater.
3
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Air Outlet
Upper Shell
PRODUCT
IDENTIFICATION
Lower Shell
Fuel Gauge
Fan Guard
Air Filter
End Cover
Fuel Tank
ON/OFF Switch
Fuel Cap
Side Cover
Flame-Out Control
Reset Button
Power Cord
Figure 1 - REMJ70
Hot Air
Outlet
Upper Shell
Lower
Shell
Fan Guard
Fuel
Tank
Fuel Cap
Side Cover
ON/OFF Switch
Fuel Gauge
Flame-Out Control
Reset Button
Power Cord
Figure 2 - REMJ150
4
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remove all packing items applied to heater for shipment.
2. Remove all items from carton.
3. Check items for any shipping damage. If heater is damaged, promptly inform
dealer where you bought heater.
UNPACKING
ASSEMBLY
These models are furnished with wheels and handles. Wheels, handles, and the
mounting hardware are found in the shipping carton.
Tools Needed
• Medium Phillips Screwdriver
• 3/8" Open or Adjustable Wrench
• Hammer
1. Slide axle through wheel support frame. Install wheels on axle.
IMPORTANT: When installing wheels, point extended hub of wheels toward
wheel support frame (see Figure 3).
2. Place cap nuts on axle ends. Gently tap with hammer to secure.
3. Place heater on wheel support frame. Line up holes on fuel tank flange with
holes on wheel support frame.
70 Model: Make sure hot air outlet end (front) of heater is over wheels.
150 Model: Make sure air inlet end (rear) of heater is over wheels.
4. Place handle or handles on top of fuel tank flange. Insert screws through
handle(s), fuel tank flange, and wheel support frame. Attach nut finger tight
after each screw is inserted.
5. After all screws are inserted, tighten nuts firmly.
70 Model
Screw
Handle
Hot Air
Outlet
Air
Inlet
150 Model
Front
Rear
Handle
Handle
Fuel Tank
Flange
Axle
Nut
Screw
Air
Inlet
Extended
Hub
Wheel
Cap
Nut
Wheel Support
Frame
Fuel Tank
Flange
Wheel
Support
Frame
Nut
Extended
Hub
Axle
Cap Nut
Wheel
Figure 3 - Wheel and Handle Assembly
5
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
The Fuel System: The air pump forces air through the air line. The air is then
pushed through the burner head nozzle. This air causes fuel to lift from the tank. A
fine mist of fuel is sprayed into the combustion chamber.
THEORY OF
OPERATION
The Air System: The motor turns the fan. The fan pushes air into and around
the combustion chamber. This air is heated and provides a stream of clean, hot air.
The Ignition System: The electronic ignitor sends voltage to the spark plug.
The spark plug ignites the fuel and air mixture.
The Flame-Out Control System: This system causes the heater to shut down
if the flame goes out.
Motor
Fan
Air Pump
Combustion
Chamber
Spark
Plug
Intake
Air
Filter
Burner
Head
Clean
Heated
Air Out
Cool
Air
In
Output
Air
Filter
Fuel
Tank
Fuel
Filter
Nozzle
Air line
To Burner
Electronic
Ignitor
Air For Fuel
System
Air For Combustion
And Heating
Fuel
Figure 4 - Cross Section Operational View
FUELS
WARNING
Use only kerosene or No. 1 fuel oil to avoid risk of fire or
explosion. Never use gasoline, naphtha, paint thinners,
alcohol or other highly flammable fuels.
Do not use heavy fuels such as No. 2 fuel oil or No. 2 Diesel. Using heavy fuels
will result in:
• clogged fuel filter and nozzle
• carbon build up on spark plug
• use of non-toxic anti-icer in fuel during very cold weather
IMPORTANT: Use a KEROSENE ONLY container. Be sure storage container is
clean. Foreign matter such as rust, dirt, or water will cause the flame-out control to
shut down heater. Foreign matter may also require you to clean fuel system often.
6
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
WARNING
Follow the minimum fresh, outside air ventilation
requirements. If proper fresh, outside air ventilation is not
provided, carbon monoxide poisoning can occur. Provide
proper fresh, outside air ventilation before running heater.
Provide a fresh air opening of at least three square feet (2800 square cm) for each
100,000 Btu/Hr rating. Provide extra fresh air if more heaters are being used.
Example: A 150,000 Btu/Hr heater requires one of the following:
• a two-car garage door (5 m wide opening) raised 8.6 cm.
• a single-car garage door (2.75 m wide opening) raised 15.3 cm.
• two, 76.2 cm wide windows raised 28 cm.
OPERATION
WARNING
Review and understand the warnings in the Safety
Information Section, page 3. They are needed to safely
operate this heater. Follow all local codes when using this
heater.
To Start Heater
1. Follow all ventilation and safety information.
2. Fill fuel tank with kerosene.
3. Attach fuel cap.
4. Plug power cord into grounded receptacle with 100 Volts, 50 or 60 Hz.
5. Turn ON/OFF switch to "ON".
Extension Cord Wire Size Requirements
Up to 100 feet (30.5 meters) long, use 16 AWG (1.0 mm2) conductor
101 to 200 feet (30.6 to 61 meters) long, use 14 AWG (1.5 mm2) conductor
If heater does not start, push in flame-out control reset button (see Figures 5
and 6).
Flame-Out
Control
Reset
Flame-
Out
Button
Control
Reset
Button
Figure 6 - Flame-Out Control Reset
Button (REMJ150)
Figure 5 - Flame-Out Control Reset
Button (REMJ70)
Continued
7
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION To Stop Heater
1. Turn ON/OFF switch to “OFF.”
2. Unplug power cord from outlet.
Continued
To Restart Heater
1. Wait 2 minutes after stopping heater.
2. Repeat steps under To Start Heater, page 7.
Note: If shipping, transport companies require fuel tanks to be empty.
1. Drain fuel tank by removing drain plug on underside of fuel tank.
2. Replace drain plug.
3. If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir,
and drain again. This will prevent excess debris from clogging filters during
future use.
STORING,
TRANSPORTING,
OR SHIPPING
4. Replace drain plug. Properly dispose of old and dirty fuel. Check with local
automotive service stations that recycle oil.
5. If storing, store heater in dry place. Make sure storage place is free of dust and
corrosive fumes.
IMPORTANT: Do not store kerosene over summer months for use during next
heating season. Using old fuel could damage heater.
PREVENTATIVE
MAINTENANCE
SCHEDULE
WARNING
Never service heater while it is plugged in, operating, or
hot. Severe burns and electrical shock can occur.
Item
How Often
How To
Fuel tank
Flush every 150-200 hours
of operation or as needed.
See Storing, Transporting, or
Shipping, above.
Air output and
Replace every 500 hours of
lint filters operation or once
a year.
See Air Output, Air Intake,
and Lint Filters, page 12.
Air intake
filter
Wash and dry with soap and
water every 500 hours of
operation or as needed.
See Air Output, Air Intake,
and Lint Filters, page 12.
Fuel filter
Clean twice a heating season
or as needed.
See Fuel Filter, pages 10
and 11.
Spark plug
Clean and regap every 600
hours operation or replace
as needed.
See Spark Plug, page 11.
Fan blades
Motor
Clean every season or as needed.
See Fan, page 15.
Not required/permanently
lubricated
8
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-
SHOOTING
WARNING
Never service heater while it is plugged in, operating, or hot.
Severe burns and electrical shock can occur.
OBSERVED FAULT POSSIBLE CAUSE
REMEDY
Wrong pump pressure
See Pump Pressure
Adjustment, page 12.
Heater ignites, but
flame-out control
shuts off heater after
a short period of time
Dirty air output, air intake, See Air Output, Air Intake
and lint filters
Dirty fuel filter
and Lint Filters, page 12.
See Fuel Filter, pages 10
and 11.
Dirt in nozzle
See Nozzle, page 13.
Dirty photocell lens
Bad flame-out control
Clean photocell lens.
Replace flame-out control.
Heater will not
ignite, but motor runs
for a short period of
time.
Wrong pump pressure
See Pump Pressure
Adjustment, page 12.
Carbon deposits on spark
plug and/or improper gap
See Spark Plug, page 11.
Dirty fuel filter
See Fuel Filter, pages 10
and 11.
See Nozzle, page 13.
Dirt in nozzle
Drain and flush fuel tank
with clean kerosene. See
Storing, Transporting, or
Shipping, page 8.
Water in fuel tank
WARNING: High voltage!
Make sure electronic
ignitor mounting is tight.
Electronic ignitor not
grounded (earthed)
Replace electronic
ignitor.
Bad electronic ignitor
Motor does not start
when heater is
ON/OFF switch in “OFF”
position
Switch to “ON” position
plugged in, fan
rotates slowly or
does not turn.
Flame-out control not reset
Reset flame-out control
button, see Figures 5 and
6, page 7.
Binding pump rotor
If fan is hard to turn, see
Pump Rotor, page 14.
9
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
PROCEDURES
WARNING
Never service heater while it is plugged in, operating, or
hot. Severe burns and electrical shock can occur.
Upper
Shell
Upper Shell Removal
1. Remove screws along each
side of heater using 5/16"
nut-driver. These screws
attach upper and lower
shells together.
2. Lift upper shell off.
3. Remove fan guard.
Figure 7 - Upper Shell Removal (REMJ70)
Upper
Shell
Fan
Guard
Figure 8 - Upper Shell Removal (REMJ150)
Fuel Filter
(REMJ70)
Fuel Filter
1. Remove side cover screws
using 5/16" nut-driver.
2. Remove side cover.
3. Pull rubber fuel line off
fuel filter neck.
4. Carefully pry bushing and
fuel filter out of fuel tank.
5. Wash fuel filter with clean
fuel and replace in tank.
6. Attach rubber fuel line to
fuel filter neck.
Side Cover
Fuel Line
7. Replace side cover.
Figure 9 - Fuel Filter Removal (REMJ70)
10
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuel Filter
(REMJ150)
Fuel Filter, Bushing,
and Lower Fuel Line
1. Remove side cover screws
using 5/16" nut-driver.
2. Remove side cover.
3. Pull upper fuel line off fuel
filter neck.
Upper
Fuel Line
4. Carefully pry bushing,
lower fuel line, and fuel
filter out of fuel tank.
5. Wash fuel filter with clean
fuel and replace in tank.
6. Attach upper fuel line to
fuel filter neck.
7. Replace side cover.
Side Cover
Figure 10 - Fuel Filter Removal (REMJ150)
Spark Plug
1. Remove upper shell (see
Spark Plug Wire
and Rubber Cap
Burner
Head
page 10).
2. Remove fan (see page 15).
3. Remove spark plug wire
from spark plug.
4. Remove spark plug from
burner head using 13/16"
open-end wrench.
5. Clean and regap spark plug
electrodes as follows:
REMJ70: .085" (2.2 mm) gap,
REMJ150: .085" (2.2 mm) gap.
6. Install spark plug in burner
head.
Spark
Plug
7. Attach spark plug wire to
spark plug.
8. Replace fan (see page 15).
9. Replace fan guard and
upper shell.
SPARK PLUG REMOVAL 70, 100 &150
Figure 11 - Spark Plug Removal
PFA/P 031A
Bend Here
to Adjust
Gap
Gap
Figure 12 - Spark Plug Gap
11
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Intake Filter
Filter End
Air Output, Air Intake,
and Lint Filters
1. Remove upper shell (see
page 10).
Cover
Fan Guard
2. Remove filter end cover
screws using 5/16" nut-
driver.
3. Remove filter end cover.
4. Replace air output and lint
filters.
5. Wash or replace air intake
filter (see Preventative
Maintenance Schedule,
page 8).
Lint Filter
Air Output
Filter
Figure 13 - Air Output, Air Intake, and Lint Filters (REMJ70)
6. Replace filter end cover.
7. Replace fan guard and
upper shell.
Air Intake Filter
Fan Guard
Filter End
Cover
IMPORTANT: Do not oil
filters.
Lint Filter
Air Output
Filter
Figure 14 - Air Output, Air Intake, and Lint Filters
(REMJ150)
Pump Pressure
Adjustment
1. Remove pressure gauge
plug from filter end cover.
2. Install accessory pressure
gauge (part number
Relief
Valve
Pressure
Gauge
Plug
HA1180).
3. Start heater (see Operation,
page 7). Allow motor to
reach full speed.
Figure 15 - Pressure Gauge Plug Removal
4. Adjust pressure. Turn relief
valve to right to increase
pressure. Turn relief valve
to left to decrease pressure.
See specifications at right
for correct pressure for
each model.
5. Remove pressure gauge.
Replace pressure gauge
plug in filter end cover.
Pump
Pressure
Gauge
Model
REMJ70
Pressure (PSI - kg/cm2)
5.0 - .35 @ 50Hz
5.4 - .38 @ 60Hz
5.0 - .35 @ 50Hz
5.3 - .37 @ 60Hz
REMJ150
Figure 16 - Adjusting Pump Pressure
12
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Nozzle
1. Remove upper shell (see
Combustion
Chamber
page 10).
2. Remove fan (see page 15).
3. Remove fuel and air line
hoses from burner head.
4. Remove spark plug wire
from spark plug.
Spark Plug Wire
and Rubber Cup
Burner Head
5. Remove spark plug from
burner head using 13/16"
open-end wrench.
6. Remove three screws
using 5/16" nut-driver and
remove burner head from
combustion chamber.
7. Place burner head into vise
and lightly tighten.
Screw
Spark
Plug
8. Carefully remove nozzle
from burner head using
5/8" socket wrench (see
Figure 18).
Air Line Hose
Fuel Line Hose
9. Blow compressed air
through face of nozzle.
This will free any dirt in
nozzle area.
Figure 17 - Removing Burner Head
10. Inspect nozzle seal for
damage.
11. Replace nozzle into burner
head and tighten firmly
(80-110 inch-pounds/9.1-
12.4 n-m).
12. Attach burner head to
combustion chamber.
13. Install spark plug in burner
head.
Nozzle
Face
Nozzle
Seal
Nozzle
14. Attach spark plug wire to
spark plug.
15. Attach fuel and airline
hoses to burner head.
16. Replace fan (see page 15).
17. Replace fan guard and
upper shell.
Burner
Head
Fuel line
Fitting
Air line
Fitting
Figure 18 - Removing Nozzle
13
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade
Air
Intake
Filter
Pump Rotor
Pump
Plate
(Procedure if rotor is binding)
1. Remove upper shell (see
page 10).
2. Remove filter end cover
screws using 5/16" nut-
driver.
Filter End
Cover
Fan Guard
3. Remove filter end cover
and air filters.
Insert
Rotor
4. Remove pump plate
screws using 5/16" nut-
driver.
Air Output
Filter
5. Remove pump plate.
6. Remove rotor, insert, and
blades.
Figure 19 - Rotor Location (REMJ70)
Pump
Blade
Plate
7. Check for debris in pump.
If debris is found, blow
out with compressed air.
8. Install insert and rotor.
9. Check gap on rotor.
Adjust to .003"/.004"
(.076/.101 mm) if needed
(see Figure 21).
Air
Intake
Filter
Filter End
Cover
Fan Guard
Insert
Rotor
Air
Note: Rotate rotor one
full turn to insure the gap is
.003"/.004" (.076/.101 mm) at
tightest position. Adjust if
needed.
Output
Filter
10. Install blades, pump plate,
air filters, and filter end
cover.
Figure 20 - Rotor Location (REMJ150)
11. Replace fan guard and
upper shell.
Gap Adjusting
Screw
12. Adjust pump pressure (see
page 12).
Note: If rotor is still binding,
proceed as follows.
.003"/.004"
(.076/.101 mm) Gap
Measured With
Feeler Gauge
13. Perform steps 1 through 6
above.
Sandpaper
14. Place fine grade sandpaper
(600 grit) on flat surface.
Sand rotor lightly in
Blade
Rotor
“figure 8” motion four
times (see Figure 22).
15. Reinstall insert and rotor.
16. Perform steps 10 through
12 above.
Gap
Adjusting
Screw
Figure 21 - Gap Adjusting
Screw Locations
Figure 22 - Sanding Rotor
14
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan
IMPORTANT: Remove fan
from motor shaft before
removing motor from heater.
The weight of the motor
resting on the fan could
damage the fan pitch.
Setscrew
Fan
1. Remove upper shell (see
page 10).
2. Use 1/8" allen wrench to
loosen setscrew which
holds fan to motor shaft.
3. Slip fan off motor shaft.
4. Clean fan using a soft cloth
moistened with kerosene or
solvent.
Motor
Shaft
Figure 23 - Fan, Motor Shaft, and Setscrew Location
5. Dry fan thoroughly.
6. Replace fan on motor
shaft. Place fan hub flush
with end of motor shaft
(see Figure 24).
Fan
7. Place setscrew on flat of
shaft. Tighten setscrew
firmly (40-50 inch-pounds/
4.5-5.6 n-m).
8. Replace fan guard and
upper shell.
Flush
Motor
Shaft
Setscrew
Figure 24 - Fan Cross Section
REMJ70
REMJ150
SPECIFICATIONS
Heat Output
(Kcal/hr)
17,640
38,500
Fuel Consumption
(liters/hr)
1.9
16
8
4.2
47
11
Fuel Tank Capacity
(liters)
Run Time per Tank
(hours)
Hot Air Output
(m3/min)
6.7@50Hz
7.5@60Hz
12.4@50Hz
13.7@60Hz
Voltage
100
100
Frequency (Hz)
Wattage (W)
50/60
200
50/60
340
Pump Pressure
(kg/cm2)
0.35@50Hz
0.38@60Hz
0.35@50Hz
0.37@60Hz
(PSI)
5.0@50Hz
5.4@60Hz
5.0@50Hz
5.3@60Hz
15
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
3
ILLUSTRATED
PARTS
2
BREAKDOWN
4
REMJ70
10
7
8
6
14
26
12
12
11
16
18
15
17
48
25
23
24
21
20
22
10-1
10-2
35
36
27
44
29
31
32
10-3
10-4
28
30
33
10-7
38
10-5
39
1
37
34
19
10-6
Burner Head Assembly
40
18-1
18-2
41
43
13
18-3
9
5
47
18-4
18-5
46
42
18-6
45
18-7
18-18
18-17
18-16
18-8
18-9
18-10
18-11
18-12
18-15
18-14
Motor and Pump Assembly
18-13
16
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts,
be sure to provide the correct model and serial numbers (from the model plate),
then the part number and description of the desired part.
PARTS LIST
REMJ70
KEY PART
NO. NUMBER
PART
DESCRIPTION
KEY PART
NO. NUMBER
PART
DESCRIPTION
QTY.
QTY.
1
2
3
4
5
6
7
8
9
097190-01
098511-188
100647-01
098512-41
097202-01
M16660
Fuel Gauge
Upper Shell
1
1
6
1
1
1
2
1
1
1
1
2
1
1
1
2
1
3
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
6
1
4
2
19
M50050
NTC-4C
Rubber Boot
Hex locknut
Shorty Bushing (wires)
Screw, #10-16 x 3/8"
Lower Shell
1
2
1
6
1
6
1
1
1
1
1
1
1
1
20
21
22
23
24
25
26
27
28
29
30
31
32
M50104-02
M11084-26
098511-81
M11271-8
097061-01
079010-18
M10908-14
M29652-04
079973-01
M16841-57
M10990-3
M50876-05
Screw, #10-16 x 1/2"
Combustion Chamber
Receptacle
Photocell Bracket
Screw, #6-32 x 3/8"
Photocell Assembly
Power Cord
Clip Nut
Relay (motor start)
Wire Assembly (red 16")
Screw, #8-32 x 3/8"
Rubber Airline
M10908-2
HA3019
102330-01
**
10
Burner Head Assembly
Nozzle
Fuel Line
10-1 100735-14
10-2 M10659-1
10-3 M10809-1
10-4 M8882
Wire Assembly (red 8 1/2")
Rubber Bushing
Fuel Filter Assembly
(Includes bushing)
Electronic Ignitor
Screw, #10-16 x 3/4"
Terminal Board
Rivet
Nozzle Seal Washer
Nozzle Seal Spring
Nozzle Seal Sleeve
Burner Head Body
Barb Fitting
10-5 M51098-02
10-6 M50820-01
10-7 M10962-2
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
101901-09
M11084-29
099125-03
099157-01
097702-01
097997-02
098513-57
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
Spark Plug
Screw, #10-16 x 1/2"
Bushing
Strain Relief Bushing
Fan
Rubber Bumper
Screw, #8-18 x 1/2"
Motor and Relay Bracket
Motor and Pump Assembly
Motor
11
M11084-27
M30865-02
099492-01
097200-01
M50631
12
13
14
15
16
17
18
Fuel Tank Cap
Flame-Out Control
Fuel Tank
097194-02AA Side Cover
M15823-39
101205-01
**
M11084-26
099177-01
097274-01
M9900-192
M27417
098226-01
097196-02
M51105-01
Screw, #10-16 x 3/8"
Hex Nut
Jumper Plug
Wire Assembly (green 16")
Drain Plug
ON/OFF Switch
Switch Seal
18-1 097286-02
18-2 079975-02
18-3 M22009
18-4 M22456-1
18-5 M29608
18-6 M29632
18-7 M29633
18-8 M29609
18-9 M12461-31
18-10 M8940
18-11 M10993-1
18-12 M27694
18-13 M22997
18-14 M29612-01
18-15 M12461-31
18-16 M50016
18-17 M8643
Pump Body
Insert
Rotor
End Pump Cover
Lint Filter
Fan Guard
Intake Filter
End Filter Cover
Screw, #10-32 x 1"
Steel Ball (1/4" Dia.)
Pressure Relief Spring
Adjusting Screw
Plug
PARTS AVAILABLE - NOT SHOWN
HA2210
Filler Neck Screen
Nameplate Decal
Warning Decal
Wire Assembly (Black 12”)
Wire Assembly (Black 7”)
1
1
1
1
1
097208-31
098070-02
M9900-170
M16841-20
Output Filter
Screw, #10-32 x 1"
Elbow, 90˚ (Barb Fitting)
Blade
18-18 FHPF3-5C
Screw, #10-32 x 5/8"
**Not available as an assembly, order parts separately.
17
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED
PARTS
2
1
BREAKDOWN
3
REMJ150
4
44
6
7
9
46
10
5
16
8
11
19
23
7-1
24
12
15
28
7-2
25
17
45
26
20
7-3
7-4
22
21
27
18
29
49
38
47
37
7-7
7-5
30
13
42
BURNER HEAD 100 EAI/EBI
PFA/P 022
7-6
31
Burner Head Assembly
40
32
35
36
10-1
33
10-3
10-4
10-5
10-2
34
41
39
48
43
10-6
14
10-7
10-18
10-17
10-8
10-9
10-16
10-15
10-10
10-14
10-11
10-13
10-12
Motor and Pump Assembly
18
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts, be
sure to provide the correct model and serial numbers (from the model plate), then
the part number and description of the desired part.
PARTS LIST
REMJ150
KEY
NO.
PART
NUMBER
KEY
QTY. NO.
PART
NUMBER
QTY.
DESCRIPTION
DESCRIPTION
1
2
3
4
5
6
7
098511-66
100647-01
098512-36
099229-01
M10908-2
HA3019
Upper Shell
1
8
1
1
2
1
1
1
2
1
1
1
2
1
3
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
1
6
1
1
4
2
1
1
1
2
1
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
101901-03
M11084-29
M51345-01
M51150-01
M51151-02
M10990-3
M50814-03
098511-82
M50104-03
M50104-01
M11084-27
M11271-8
M10908-14
098513-81
097702-01
097997-02
099492-01
102330-01
Electronic Ignitor
Screw, #10-16 x 3/4"
Fuel Line
1
2
1
1
1
1
1
1
2
2
6
8
1
1
1
1
1
1
1
4
1
1
1
1
Screw, #10-16 x 1/2"
Combustion Chamber
Photocell Bracket
Screw, #6-32 x 3/8"
Photocell Assembly
Burner Head Assembly
Nozzle
Nozzle Washer
Nozzle Spring
Nozzle Sleeve
Burner Head Body
Barb Fitting
Spark Plug
Screw, #10-16 x 1/2"
Fan
Motor and Pump Assembly
Motor
Pump Body
Screw #10-32 x 5/8"
Rotor Insert
Pump Rotor
Pump End Cover
Intake Filter
Filter End Cover
Steel Ball, 1/4" diameter
Relief Spring
Adjusting Screw
Plug
Screw #10-32 x 1"
Output Filter
Screw, #10-32 x 1"
Lint Filter
Barb Fitting
Fuel Filter
Fuel Line Tube
Rubber Bushing
Air Line
Lower Shell
Bushing
Bushing
Screw, #10-16 x 1/2"
Clip Nut
Screw, #8-32 x 3/8"
Fuel Tank
Fuel Tank Cap
Flame-Out Control
Strain Relief Bushing
Power Cord
**
7-1
100735-07
M10659-1
M10809-1
M8882
M50924-08
M50820-02
HA3012
M11084-27
102042-01
**
7-2
7-3
7-4
7-5
7-6
7-7
8
9
10
10-1 102234-01
10-2 079975-02
10-3 FHPF3-5C
10-4 M22009
10-5 M22456-1
10-6 M50545
10-7 M12179
10-8 M16545
10-9 M8940
10-10 M10993-1
10-11 M27694
10-12 M22997
10-13 M12461-31
10-14 M12244-1
10-15 M12461-31
10-16 M11637
10-17 M50820-02
10-18 M8643
M51077-07AA Side Cover
M11084-27
099125-02
099157-02
097196-02
M16841-57
M27417
Screw, #10-16 x 1/2"
Terminal Board
Rivet
Switch Seal
Wire Assembly (Red, 8 1/2")
Drain Plug
(Includes “O” Ring)
Hex Nut
Receptacle
Screw, #10-16 x 3/8"
Button Plug
Screw, #10-16 x 1/2"
Wire Assembly (Green, 16")
Jumper Plug
1
1
1
2
1
2
1
1
1
42
43
44
45
46
47
48
49
099177-01
097202-01
099230-01
099213-01
M11084-27
M9900-192
097274-01
M50050
Rubber Boot
Blade
11
M50631
Rubber Bumper
Motor Mounting Bracket
Fuel Gauge
ON/OFF Switch
Hex Lock Nut, 1/4-20
Fan Guard
PARTS AVAILABLE - NOT SHOWN
12
13
14
15
16
101206-01
097190-03
098226-01
NTC-4C
HA2210
Filler Neck Screen
General Information Decal
Warning Decal
1
1
1
1
097208-32
098070-02
M16841-20
M51114-01
Wire Assembly (Black 7”)
** Not available as an assembly. Order parts separately.
19
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEELS AND HANDLES
KEY PART
NO. NUMBER
PART
DESCRIPTION
REMJ70
QTY.
REMJ150
QTY.
1
097198-02
097777-03
M12345-33
097197-02
M12831-3
NTC-3C
097766-01
M28526
M51015-04
M16801-2
Handle (Rear)
Handles
1
—
4
1
—
4
2
2
1
—
—
2
8
—
1
8
2
2
—
1
2
3
Screw, #10-24 x 1 3/4"
Wheel Support Frame
Wheel Support Frame
Hex Nut, #10-24
Wheel
Cap Nut
Axle
Axle
4
5
6
7
REMJ70
REMJ150
1
1
2
2
7
3
5
4
4
5
6
7
6
3
20
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Plug
Black
WIRING
DIAGRAMS
Green
White
Plug
Black
Power On Switch
Receptacle
Black
White
Green
White
White
B
Green/
Yellow
Motor
Flame
Out
Control
Terminal
Board
Blue Blue
White
Photo-
cell
Ignitor
Spark Plug
Red
Reset
Button
Red
R
Red
Black
Red
Relay
Figure 25 - Wiring Diagram (REMJ70)
Power Plug
Green
Black
Plug
White
Black
Power On Switch
Receptacle
White
White
Black
Green/
Yellow
Motor
White
Terminal
Board
B
Ignitor
Spark Plug
Flame
Out
Control
Green
Red
Blue
Blue
White
Red
Reset
Button
R
Red
Figure 26 - Wiring Diagram (REMJ150)
ACCESSORY
Purchase accessory from your
local dealer.
AIR GAUGE KIT - HA1180
For all models. Special tool to
check pump pressure.
21
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
22
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
23
102961
Download from Www.Somanuals.com. All Manuals Search And Download.
102961-01
Rev. A
06/96
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|