43-160.fm Page 1 Thursday, August 12, 1999 2:25 PM
Cat. No. 43-160
OWNER’S MANUAL
Please read before using this equipment.
Wireless Phone Jack System
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 3 Thursday, August 12, 1999 2:25 PM
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to the presence of unin-
sulated dangerous voltage within the product’s enclosure that
might be of sufficient magnitude to constitute a risk of electric
shock. Do not open the product’s case.
This symbol is intended to inform you that important operating
and maintenance instructions are included in the literature ac-
companying this product.
!
OPERATING PRECAUTIONS
Read and follow these precautions when installing and using the
Wireless Phone Jack System.
• Read and understand all instructions.
• Follow all warnings and instructions marked on the system
and in this manual.
• Unplug this system from the wall outlet before cleaning. Do
not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
• Do not use this system near water; for example, near a bath
tub, washbowl, kitchen sink, or laundry tub, in a wet base-
ment, or in or near a swimming pool.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 4 Thursday, August 12, 1999 2:25 PM
• This system should never be placed near or over a heat radi-
ator or register. This system should not be placed in a built-in
installation unless proper ventilation is provided.
• This system should only be operated from the type of power
source indicated in this manual and on the system’s label. If
you are not sure of the type of power supplied to your home
or building, consult your local Radio Shack store or the local
power company.
• Never spill liquid of any kind on the system.
• To reduce the risk of electric shock, do not disassemble this
system, but take it to a qualified service facility when service
or repair is required. Opening or removing the covers might
expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the system is
subsequently used.
• Unplug the system from the wall outlet and refer servicing to
a qualified service facility under the following conditions:
A. When the AC plug is damaged
B. If liquid has been spilled into the system
C. If the system has been exposed to rain or water
D. If the system does not operate normally by following
the operating instructions
E. If the system has been dropped or it appears to be
damaged
F.
If the system exhibits a distinct change in performance
• Avoid using a telephone, other than a cordless phone, during
an electrical storm. There is a remote risk of electric shock
from lightning.
• Do not use the telephone to report a gas leak in the area of
the leak.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 5 Thursday, August 12, 1999 2:25 PM
FCC INFORMATION
We have designed your Wireless Phone Jack System to conform
to federal regulations, and you can connect it to most telephone
lines. However, each device that you connect to the phone line
draws power from it. We refer to this power draw as the device’s
Ringer Equivalence Number, or REN (the REN is shown on the
base unit’s label).
If you are using more than one phone or other device on the line,
add up all the RENs. If the total is more than five, your phones
might not ring. In rural areas, a total REN of three might impair
ringer operation. If ringer operation is impaired, disconnect one of
the devices from the line.
Your Wireless Phone Jack System has a REN of 0.7dB; there-
fore, it should not affect your phones’ ability to ring. Also, the
phone you plug into the extension unit does not place any load on
the telephone line. However, the phone you plug into the base
unit might affect your phones’ ability to ring.
In the unlikely event that your Wireless Phone Jack System caus-
es problems on the phone line, the phone company can tempo-
rarily discontinue your service. If this happens, the phone
company attempts to notify you in advance. If advance notice is
not practical, the phone company notifies you as soon as possi-
ble and advises you of your right to file a complaint with the FCC.
Also, the phone company can make changes to its lines, equip-
ment, operations, or procedures that could affect the operation of
this system. The telephone company notifies you of these chang-
es in advance, so you can take the necessary steps to prevent in-
terruption of your telephone service.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 6 Thursday, August 12, 1999 2:25 PM
FCC PART 68 AND CLASS B NOTICES
This Wireless Phone Jack System complies with Part 68 of FCC
Rules. You must, upon request, provide the FCC Registration
Number and the REN to your phone company. These numbers
are located on the base unit’s label.
Note:
You must not connect your Wireless Phone Jack System
to any of the following:
• coin-operated systems
• party-line systems
• most electronic key phone systems
This equipment complies with the limits for a Class B digital de-
vice as specified in Part 15 of
Rules. These limits provide
FCC
reasonable protection against radio and TV interference in a resi-
dential area.
However, your equipment might cause TV or radio interference
even when it is operating properly. To eliminate interference, you
can try one or more of the following corrective measures:
• Reorient or relocate the TV or radio
• Increase the distance between the equipment and the radio
or TV
• Use outlets on different electrical circuits for the equipment
and the radio or TV
Consult your local Radio Shack store if the problem still exists.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 7 Thursday, August 12, 1999 2:25 PM
LIGHTNING
Your Wireless Phone Jack System has built-in protection circuits
to reduce the risk of damage from surges in telephone line and
power line current. These protection circuits meet or exceed the
FCC requirements. However, lightning striking the telephone or
power lines can damage your telephone.
Lightning damage is not common. Nevertheless, if you live in an
area that has severe electrical storms, we suggest that you un-
plug your phone during storms to reduce the possibility of dam-
age.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 8 Thursday, August 12, 1999 2:25 PM
USING THE SYSTEM
It is very important that you follow all instructions in the order giv-
en. If you have a problem, unplug both units from the AC outlets,
unplug the phone(s) from the units, and start over (or see “Trou-
bleshooting” on Page 13).
INSTALLATION
1
3
2
1. Plug the base unit into a standard AC outlet that is near a
modular telephone jack. (The base unit has two modular
jacks on one side.)
Caution:
Do not plug the base or extension unit into a power
strip or surge protector/AC line filter.
2. Plug one end of the supplied modular telephone cord into the
LINE
jack on the side of the base. Then plug the other end of
the cord into a modular telephone jack.
Note:
Be sure to plug in the base unit before you plug in the
extension unit.
3. If desired, connect a telephone to the base unit by plugging
PHONE
its modular cord into the
jack on the side of the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 9 Thursday, August 12, 1999 2:25 PM
4. Plug the extension unit into any AC outlet. (The extension
unit has only one modular jack.) Then plug a telephone’s
modular cord into the jack on the side of the extension unit.
Notes:
• Longer modular telephone cords are available from your
local Radio Shack store.
• If your phone line jack is not a modular jack, you can update
the wiring yourself, using jacks and adapters available at
your local Radio Shack store. Or, you can let the phone com-
pany update the wiring for you. The USOC number of the
jack to be installed is RJ11C.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 10 Thursday, August 12, 1999 2:25 PM
SETTING THE SECURITY CODE
This system has preset security codes which prevent interference
and background noise caused by similar systems. If you
encounter interference, follow these steps to set your security
codes.
Note:
You should only need to set the security code if you get in-
terference from another system.
1. With both the base and extension unit(s) installed and any
connected telephones on hook, press the coding button on
the side of the base unit with a pencil. The green indicator on
the base turns on.
Indicator
Coding Button
Base
2. Press the coding button on the extension unit within 5 min-
utes.
• If the code is successfully set, the extension unit’s indica-
tor blinks once.
• If the code is not set, the indicator continues to flash. Try
pressing the coding button on the extension unit several
times until the indicator stops flashing. if you cannot make
the indicator stop flashing, start over again at Step 1.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 11 Thursday, August 12, 1999 2:25 PM
3. Wait for the base unit’s indicator to turn off. Then lift the
extension telephone’s handset and confirm that you hear a
dial tone and that there is no interference or background
noise. If there is a problem, repeat these steps.
If you cannot get a dial tone, unplug the cords from both phone
jacks and reset the units (see “Resetting the System” on
Page 12).
ADDING MORE EXTENSION UNITS
You can add as many extension units (Cat No. 43-161) to the
system as you want. Simply install the extension by following
Steps 4 and 5 in “Installation.” Then follow the steps in “Setting
the Security Code” on Page 10 to set each extension’s code.
You can use only one extension at a time, even if you install more
than one. If you lift the receiver on a phone connected to an ex-
tension unit while another extension unit is being used, you hear
a busy signal.
USING THE SYSTEM WITH A COMPUTER
MODEM
Simply plug your computer modem’s telephone cord into an ex-
tension unit’s modular jack. The system supports speeds up to
14,400 bps.
Note:
If there is static on the system, you might need to set your
modem to a slower speed for effective communications.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 12 Thursday, August 12, 1999 2:25 PM
RESETTING THE SYSTEM
If your Wireless Phone Jack System is not operating, you might
need to reset it. Follow these steps to reset the system.
1. Unplug both the base and extension unit(s) from the AC out-
lets and disconnect all phones from the units.
2. Press the coding button on the base for 5 seconds.
3. Press the coding button on each extension for 5 seconds.
4. Reinstall the system.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 13 Thursday, August 12, 1999 2:25 PM
TROUBLESHOOTING
We do not expect you to have any problems with your system,
but if you do, the following suggestions might help. If you still
have problems, disconnect the base and all extensions and take
them to your local Radio Shack store for assistance.
Problem
Suggestion
Static interference.
Move the base or extension unit(s).
Fluorescent lights, light dimmers,
computer surge protectors, and
home automation controllers can
cause interference.
Cannot set the secu-
rity code.
Move the base or extension unit(s).
Try the security code procedure sev-
eral times. If that does not work,
reset the system then try again.
Cannot dial out.
Decrease the distance between the
base and the extension unit(s).
Be sure the outlet has power. During
a power failure, only phones con-
nected to the base or directly to the
phone jacks operate.
Phone does not ring.
Decrease the distance between the
base and the extension unit(s).
No dial tone or a high
pitched beep from the
handset.
Reset the system.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 14 Thursday, August 12, 1999 2:25 PM
CARE AND MAINTENANCE
Your Radio Shack Wireless Phone Jack System is an example of
superior design and craftsmanship. The following suggestions
will help you care for your system so you can enjoy it for years.
• Keep the system dry. If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode electronic circuits.
• Use and store the system only in normal temperature envi-
ronments. Temperature extremes can shorten the life of
electronic devices, and distort or melt plastic parts.
• Handle the system gently and carefully. Dropping it can dam-
age circuit boards and cases and can cause the system to
work improperly.
• Keep the system away from dust and dirt, which can cause
premature wear of parts.
• Wipe the system with a damp cloth occasionally to keep it
looking new. Do not use harsh chemicals, cleaning solvents,
or strong detergents to clean your system.
Modifying or tampering with the system’s internal components
can cause a malfunction, invalidate its warranty, and void your
FCC authorization to operate it. If your system is not performing
as it should, take it to your local Radio Shack store for assis-
tance. If the trouble is affecting the telephone lines, the phone
company can ask you to disconnect your Wireless Phone Jack
System until you have resolved the problem.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 15 Thursday, August 12, 1999 2:25 PM
NOTES
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-160.fm Page 16 Thursday, August 12, 1999 2:25 PM
Limited One-Year Warranty
This product is warranted by Radio Shack against manufacturing defects in ma-
terial and workmanship under normal use for one (1) year from the date of pur-
chase from Radio Shack company-owned stores and authorized Radio Shack
franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RADIO SHACK
MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, IN-
CLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PRO-
VIDED HEREIN, RADIO SHACK SHALL HAVE NO LIABILITY OR RESPONSI-
BILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH
RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR
INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIM-
ITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPE-
CIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RADIO
SHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts
or the exclusion of incidental or consequential damages, so the above limita-
tions or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and
the Radio Shack sales receipt as proof of purchase date to any Radio Shack
store. Radio Shack will, at its option, unless otherwise provided by law: (a) cor-
rect the defect by product repair without charge for parts and labor; (b) replace
the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made,
become the property of Radio Shack. New or reconditioned parts and products
may be used in the performance of warranty service. Repaired or replaced
parts and products are warranted for the remainder of the original warranty pe-
riod. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to
acts of God, abuse, accident, misuse, improper or abnormal usage, failure to
follow instructions, improper installation or maintenance, alteration, lightning or
other incidence of excess voltage or current; (b) any repairs other than those
provided by a Radio Shack Authorized Service Facility; (c) consumables such
as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insur-
ance costs; or (f) costs of product removal, installation, set-up service adjust-
ment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Radio Shack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600,
Fort Worth, TX 76102
We Service What We Sell
3/97
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
3/98
Printed in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|