ET 3229 Big Button Speakerphone
OWNER’S MANUAL — Please read before using this equipment.
Your RadioShack Big Button Speakerphone
lets you store up to 13 frequently called tele-
phone numbers in memory for quick, easy di-
aling of any stored number. Its features
include:
In the unlikely event your phone causes
problems on the phone line, the telephone
company can disconnect your service. The
phone company tries to notify you in ad-
vance. If advance notice is not practical, the
telephone company notifies you as soon as
possible and advises you of your right to file
a complaint with FCC.
Big Button Keypad — provides easy button
recognition.
Built-in Speakerphone — gives you hands-
free operation.
Your telephone complies with Part 68 of FCC
Rules, you must, upon request, provide the
FCC registration numbers and the REN to
your telephone company. Both numbers are
shown on the bottom of the telephone.
13 Memory Locations — allows quick, easy
dialing of frequently called numbers.
Ring Indicator — a lighted bar signals an in-
coming call even if the ringer is turned off.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received, in-
cluding interference that may cause undes-
ired operation.
Adjustable Ringer and Receiver Volume
— lets you adjust the ringer and receiver’s
volume to the desired level.
Your telephone is ETL listed to UL standards
and meets all applicable FCC requirements.
Note: You must not connect your telephone
to:
FCC STATEMENT
• Coin-operated systems
We have designed your telephone to con-
form to federal regulations, and you can con-
nect it to most telephone lines. However,
each device that you connect to the tele-
phone line draws power from the line. We re-
fer to this power draw as the phone’s ringer
equivalence number (REN). The REN is on
the bottom of your phone.
• Party-line systems
• Most electronic key telephone systems
Lightning
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
(telephone and power) line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
If you use more than one phone or other de-
vice on the line, add up all the RENs. If the
total is more than five (three in rural areas),
your phone might not ring. If the ringer oper-
ation is impaired, remove one of the devices
from the line.
© 2001 RadioShack Corporation. All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
slots with the wall plate studs and slide
the phone downward to secure it.
meet these specifications could damage
the telephone or the adapter.
4. Press and lift up the handset holder,
rotate it 180°, then snap it back so it holds
the handset.
• Always connect the AC adapter to the
telephone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you dis-
connect it from the telephone.
To mount the phone directly on a wall, in addi-
tion to the preceding steps, you need two
screws (not supplied) with heads that fit into
the keyhole slots on the bottom of the base.
Plug the barrel plug of the supplied adapter
into the DC 9V jack at the back of the tele-
phone. Plug the other end into a nearby AC
outlet.
Drill two holes 315/16 inches (100 mm) apart.
Then thread a screw into each hole, letting the
5
heads extend about /16 inches (8mm) from
Setting the Ringer
the wall.
If you do not want to hear the phone ring, set
RINGER to OFF. You can still make calls with
the ringer off, and you can answer calls if you
hear another phone on the same phone line
ring. The bar-shaped ring indicator flashes
when the phone rings, even when the ringer is
off. If you want to hear the phone ring, set
RINGER to HI or LO.
Substitute the long modular cord for the short
cord mentioned in step 2.
Connecting the Handset
Plug one end of the coiled cord into the modu-
lar jack on the handset. Then connect it to the
jack on the left side of the telephone base.
Setting the Dialing Mode
Note: Your local RadioShack store sells a va-
riety of longer coiled handset cords, which are
especially useful when you mount the phone
on a wall.
Set T/P (TONE/PULSE) for the type of service
you have. If you are not sure which type you
have, do this simple test.
Connecting an AC Adapter
1. Set T/P to T. Lift the handset and listen for
a dial tone.
Your telephone operates from telephone line
power. In some areas, however, the tele-
phone might not provide enough power to op-
erate all of your telephone’s features. If the
volume of the speaker is too low, even with
the volume control set to its highest level, or if
the speaker does not work, you need to con-
nect the supplied AC adapter.
2. Press any number except 0. If your phone
requires that you dial an access code (9,
for example) before you dial an outside
number, do not press the access code
number either.
If the dial tone stops, you have touch-
tone service. Leave the setting to T.
Cautions:
If the dial tone continues, you have pulse
service. Set T/P to P.
You must use a Class 2 power
source that supplies 9V DC and
!
delivers at least 200 mA. Its
center tip must be set to positive and its
plug must fit the telephone's DC 9V jack.
The supplied adapter meets these speci-
fications. Using an adapter that does not
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Enter the telephone number, then press
OPERATION
STORE again.
Using the Speakerphone
3. Press the direct memory location (1-3) at
the top of the phone or the desired stan-
dard memory location (0-9) using the
standard keypad.
You can use the built-in speakerphone in-
stead of the handset. When you press SPEAK-
ERPHONE, the indicator lights and the phone
connects the telephone line. To disconnect
the telephone line, press SPEAKERPHONE
again. The indicator goes off.
Notes:
• Since pressing STORE does not break the
dial tone, the phone company “line alert”
signal may occur when entering longer
numbers. This does not affect number
storage.
If you are using the handset and you want to
switch to the speakerphone, press SPEAKER-
PHONE. Return the handset to the cradle.
To switch from the speakerphone to the hand-
set, lift the handset. When you lift up the
handset, the speakerphone turns off automati-
cally.
• To replace a number in one of the mem-
ory locations repeat steps 1 through 3.
During step 2, enter the new number in
any memory location you wish to change.
If you decide to change from speakerphone to
handset operation during redial or memory di-
aling, let the number completely dial before
you lift the handset.
Dialing a Stored Number
To dial a number stored in direct memory,
press the desired direct memory location (1-3)
at the top of the phone.
Setting the Receiver and Speaker-
phone Volume
To dial a number stored in a standard memory
location, press MEMORY, then the desired
memory key (0-9).
Slide RECEIVER VOL to LO/MED/HI as desired
to adjust the handset receiver volume.
Chain-Dialing Memory Numbers
Slide SPEAKER VOL to set the speakerphone
volume as desired.
If you frequently use special telephone servic-
es, you can save time by storing the phone
number of the service in one memory location
and the rest of the information, such as a long
distance number, in another memory location.
Using Mute
To temporarily disconnect the speakerphone
or handset without ending the call, so you can
talk privately with someone in the room, press
MUTE. The MUTE indicator lights. To resume
your call, press MUTE. The MUTE indicator
goes off.
To chain-dial, enter the memory location of
the service number first. Then when the ser-
vice answers, enter the memory location of
the other information.
Note: We recommend you do not store secu-
rity numbers, such as personal access codes
for bank-by-phone services, in any memory
location.
Storing a Number in Memory
The telephone has 3 direct and 10 standard
phone memory storage locations.
1. With the handset off hook or SPEAKER-
PHONE on, press STORE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Redial
You can quickly dial the last number dialed by
pressing REDIAL/PAUSE when you hear a dial
tone. The redial number is replaced each time
you dial a new number. The redial memory
holds up to 32 digits, to store long distance as
well as local numbers.
Note: If you press FLASH while dialing a num-
ber, only the digits after FLASH are stored in
redial memory.
Using Flash
Many special telephone services, such as Call
Waiting, require a switchhook signal. The
FLASH button provides the electronic equiva-
lent of a switchhook operation.
For example, if you have Call Waiting, you
can put a call on hold and take a second in-
coming call on the same line by pressing
FLASH.
Only the digits you dial after you press FLASH
are stored in redial memory.
Note: If you do not have any special phone
services, pressing FLASH might disconnect
the current call.
Using Pause
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before dialing an outside
number. When you manually dial a number, or
when you store a number in memory, you can
have your telephone pause anywhere during
the dialing sequence. Simply press REDIAL/
PAUSE at the desired location.
When you redial or memory dial a number, the
telephone pauses for about 3 to 6 seconds at
the pause entry. For longer pauses, press RE-
DIAL/PAUSE again.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying or tampering with the telephone’s
internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
telephone is not performing as it should, take
it to your local RadioShack store for assis-
tance. If the trouble is affecting the telephone
lines, the phone company can ask you to dis-
connect your telephone until you have re-
solved the problem.
TROUBLESHOOTING
If your telephone is not operating properly, go
through this checklist.
Is the phone properly connected?
Is the T/P switch set correctly?
If the telephone’s volume level drops or it be-
gins to make strange sounds, determine if
other phones have been picked up on the
same line. This phone might not operate when
other phones are active on the same line (es-
pecially in areas with low telephone voltage).
Hang up the other phones to correct the prob-
lem.
If any additional telephone devices have been
added at or about the time this phone’s perfor-
mance diminished, recalculate the total REN
for your devices (see “FCC STATEMENT” on
Page 1).
If the volume of the speaker is too low, even
with the volume control set to its highest level,
or if the speaker does not work, connect the
supplied AC adapter (see “Connecting an AC
Adapter” on Page 3).
When the party on the phone cannot hear
you, but you can hear them, check the MUTE
indicator. If the light is on, press MUTE so it is
off.
If you still have problems, disconnect the
phone. If other phones on the same line work
properly, the fault is in this phone or its instal-
lation. If you cannot find the problem, take
your phone to your local RadioShack store for
assistance.
CARE
Keep the telephone dry; if it gets wet, wipe it
dry immediately. Use and store the telephone
only in normal temperature environments.
Handle the telephone carefully; do not drop it.
Keep the telephone away from dust and dirt,
and wipe it with a damp cloth occasionally to
keep it looking new.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
A QUICK LOOK AT YOUR PHONE
DIRECT MEMORY (see “Storing a Number in
Memory” and “Dialing a Stored Number” on
Page 4).
RING INDICATOR BAR
MEMORY (see “Dialing a
Stored Number” on
Page 4).
STORE (see “Storing a
Number in Memory” on
Page 4).
MUTE (see “Using
Mute” on Page 4).
FLASH (see “Using Flash”
on Page 5).
REDIAL/PAUSE (see
“Using Redial” on
Page 5 and “Using
Pause” on Page 5).
SPEAKERPHONE (see “Using the Speak-
erphone” on Page 4).
RECEIVER volume control for adjusting the
volume of the handset receiver (see “OPERA-
TION” on Page 4).
DC 9V jack for connecting an optional AC adapter
(see “Connecting an AC Adapter” on Page 3).
Control for adjusting the SPEAK-
ERPHONE volume.
LINE jack
RINGER switch for adjusting ringer volume (see “Set-
ting the Ringer” on Page 3).
T/P switch for setting the Dialing Mode (see
“Setting the Dialing Mode” on Page 3).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-3229
06A01
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
Download from Www.Somanuals.com. All Manuals Search And Download.
|