Precor Treadmill 921i User Manual

R
R
Owner’s Manual  
Low Impact  
Treadmills featuring  
the Heart Rate  
Interactive System  
R
page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Personal Safety  
Assemble and operate the treadmill on a solid, level surface. Locate the treadmill at least 4  
feet from walls or furniture. Keep the area behind the treadmill clear.  
Check the M9.21i or M9.21si treadmill before each use. Completely assemble the treadmill  
before using it.  
Turn OFF (O) and unplug the treadmill when adjusting or working near the rear roller. Do not  
adjust the running belt when someone is standing on the unit.  
Keep all electrical components, such as the motor, power cord, and ON/OFF (I/O) switch,  
away from water or other liquids to prevent shock. Do not set anything on the handrail,  
electronic console, or hood. Never place liquids on any part of the unit.  
Always attach the safety clip to your clothing at waist level prior to beginning your workout.  
The safety clip is connected by a cord to the magnetic safety key in the electronic console. If  
you encounter difficulties, you can stop the running belt by pulling on the cord to disengage  
the magnetic safety key from inside the console. To resume operation, the magnetic safety  
key must be replaced.  
When the treadmill is not being used, remove the magnetic safety key and store it in a safe  
place to prevent unauthorized use.  
Wear proper exercise clothing and shoes for your workout—no loose clothing. Do not wear  
shoes with heels or leather soles. Check the soles of your shoes and remove any dirt and  
embedded stones. Tie long hair back.  
Keep all loose clothing and towels away from the running surface. The running belt will not  
stop immediately if an object becomes caught in the belt or rollers.  
Use care when getting on or off the treadmill. Use the handrails whenever possible. Step onto  
the running belt when the speed is at or below 1 mile per hour (1.6 kilometers per hour).  
Never step off the treadmill while the running belt is moving.  
Before the running belt begins moving (prior to your workout), and after it stops (at the end of  
your workout), straddle the belt by placing your feet firmly on the right and left side platforms.  
Never turn ON the treadmill when someone is standing on the machine.  
Keep your body and head facing forward. Never attempt to turn around on the treadmill when  
the running belt is moving.  
Do not rock the unit. Do not stand on the handrails, electronic console, or hood.  
Do not attempt to service the treadmill yourself other than the assembly and maintenance  
instructions found in this manual.  
Do not overexert yourself or work to exhaustion.  
Stop your workout immediately if you feel any pain or abnormal symptoms, and consult your  
physician  
Precor Heart Rate Option—Safety Guidelines  
The Precor Heart Rate Option was created and designed exclusively for Precor products. The  
equipment is extremely sensitive—you should use the heart rate option with this in mind and take  
time to read the following guidelines:  
Handle the Precor Heart Rate Option with care. Do not drop the equipment. It might damage  
the transmitter and you could void the manufacturer’s limited warranty.  
Do not use the chest strap near strong electromagnetic radiation sources. Television sets,  
electric motors, radios, and high voltage power lines can interfere with the heart rate signal  
that is being transmitted to the receiver and might affect the heart rate readings that appear on  
the electronic console.  
page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use only one chest strap at a time inside the range of the receiver. If the receiver tries to  
process several signals simultaneously, an incorrect heart rate reading could result. Be sure to  
keep any other transmitters at least 5 feet (1.5 meters) away from the receiver on your M9.21i  
or M9.21si treadmill.  
Keep the equipment dry. Although the chest strap should not be immersed in water, wetting the  
electrodes and your chest will improve the initial performance. Note that perspiration on the  
chest strap during workouts is normal and actually enhances the signal being sent from the  
chest strap’s transmitter.  
To conduct the electrical impulses from your heart, the chest strap’s electrodes require a  
certain percentage of salts and minerals in the water used to wet them. The electrodes continue  
to transmit your heart rate reading as long as they are in contact with your skin and your skin is  
providing enough moisture through your perspiration to keep the electrodes wet. However, if  
the concentration of salts in your perspiration is not high enough to conduct electrical impulses  
and send them to the receiver, your heart rate reading will appear erratic or not appear at all.  
Some people cannot use the heart rate feature because they do not have the proper body  
chemistry.  
Do not use the chest strap if you are taking any medication or have a cardiac pacemaker.  
Inaccurate heart rate readings can occur due to medication or electrical impulses from the  
cardiac pacemaker.  
Stretching or bending the electrode strips on the chest strap may cause the strips to lose their  
conductivity. Handle the chest strap with care.  
After extensive use, the chest strap (transmitter) may wear out, causing inaccurate heart rate  
readings. With every use, check the strap for excessive wear and replace it if necessary. See  
Obtaining Service in the maintenance section of this manual.  
Precor treadmills are designed for the enjoyment of the serious runner as well as the dedicated  
walker. By following the above precautions and using good common sense, you will have many safe  
and pleasurable hours of healthful exercise with your Precor treadmill.  
Information Regarding Use in the U.S.A. and Canada  
Federal Communications Commission, Part 15  
The M9.21i or M9.21si treadmill has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. The M9.21i or M9.21si treadmill  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the owner’s manual instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
If the M9.21i or M9.21si treadmill does cause harmful interference to radio or television reception,  
which can be determined by turning the M9.21i or M9.21si treadmill OFF and ON, you are encour-  
aged to try to correct the interference using one or more of the following measures:  
Reorient or relocate the receiving antenna for your TV, radio, VCR, etc.  
Increase separation between the M9.21i or M9.21si treadmill and the receiver (TV, radio, etc.).  
Connect the M9.21i or M9.21si treadmill into a different power outlet—on a dedicated circuit  
different from the one used by the receiver (TV, radio, etc.). No other appliance should be  
plugged into the same power outlet that the treadmill is connected to.  
Consult your dealer or an experienced radio/TV technician for help.  
WARNING  
Per FCC rules, changes or modifications not expressly approved by Precor, could void the user’s  
authority to operate the equipment.  
page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Canadian Department of Communications  
This digital apparatus does not exceed the (Class B) limits for radio noise emissions from digital apparatus  
set out in the Radio Interference Regulations of the Canadian Department of Communications.”  
Le présent appareil numérique n’émet pas de bruits radioéélectriques dépassant les limites  
applicables aux appareils numériques (de la class B) prescrites dans le Règlement sur le brouillage  
radioélectrique édicté par le ministére des Communications du Canada.”  
Grounding Instructions  
The M9.21i or M9.21si Low Impact Treadmill must be grounded. If it should malfunction or break  
down, grounding provides a path of least resistance for electric current which reduces the risk of  
electrical shock. The treadmill is equipped with a power cord having an equipment-grounding  
conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is  
properly installed and grounded in accordance with all local codes and ordinances.  
Diagram A  
Proper grounding plug and  
power outlet for 120v  
connection  
DANGER  
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.  
Check with a qualified electrician or service person if you are in doubt as to whether the treadmill is  
properly grounded. Do not modify the plug provided with the treadmill—if it doesn’t fit the outlet,  
get a proper outlet installed by a qualified technician.  
The treadmill is for use on a nominal 120-volt circuit (refer to the WARNING below and to the Installa-  
tion Requirements on page 9) and has a grounding plug that looks like the plug illustrated in Diagram  
A.  
WARNING  
This product is rated for use on a circuit having a nominal rating of 120 volts, 15 amps and is  
factory-equipped with a specific electric cord and plug to permit connection to a proper electric  
circuit. Make sure that the product is connected to an outlet having the same configuration as the  
plug. No adapter should be used with this product. If the treadmill must be reconnected for use on  
a different type of electric circuit, the reconnection should be made by qualified service personnel.  
ATTENTION: Haute Tension  
Débranchez avant de réparer  
page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Before You Begin ............................................................ 1  
1
2
Unpacking the M9.21i or M9.21si Low Impact Treadmill................. 1  
Setting Up the Low Impact Treadmill ............................ 3  
Installation Requirements ............................................................... 3  
Assembly Instructions ..................................................................... 3  
Checking the Alignment of the Running Belt................................... 8  
Using the Low Impact Treadmill .................................... 9  
3
Locating the ON and OFF Switch ................................................... 9  
Using the Magnetic Safety Key ....................................................... 9  
Understanding the Electronic Console. ......................................... 10  
Displays on the Electronic Console............................................... 10  
Keys on the Electronic Console .................................................... 11  
Customizing the Display ............................................................... 12  
Changing the Display to U.S. Standard or Metric  
Turning the Smart Rate Display On or Off  
Selecting the TIME or DISTANCE prompt  
Working Out on the Low Impact Treadmill ................. 13  
Using the Quick Start Feature....................................................... 15  
Retrieving the Previous Workout Program .................................... 15  
Pausing Your Workout .................................................................. 15  
Cooling Down After a Workout...................................................... 15  
Ending Your Workout .................................................................... 15  
Changing the Interval Course Profile ............................................ 16  
Using the Weight Loss Program ................................................... 17  
Using the Manual Course Program ............................................... 18  
Using the Random Course............................................................ 18  
Using a Preprogrammed Course on the M9.21si .......................... 18  
Creating Custom Courses on the M9.21si .................................... 19  
Deleting Custom Courses on the M9.21si..................................... 19  
4
Using the Precor Heart Rate Option ............................ 20  
Wearing the Chest Strap Transmitter............................................ 20  
Utilizing the Heart Rate Interactive System................................... 21  
Using the Heart Rate Course ........................................................ 21  
Correcting Inconsistent Heart Rate Readings ............................... 22  
5
Getting the Most Out of Your Workout........................ 23  
How Hard Should I Exercise? ....................................................... 23  
How Long Should I Exercise? ....................................................... 25  
How Often Should I Exercise? ...................................................... 25  
6
7
Maintaining the Low Impact Treadmills ...................... 26  
Cleaning the Equipment................................................................ 26  
Changing the Battery in the Chest Strap....................................... 26  
Storing the Chest Strap................................................................. 27  
Aligning the Running Belt.............................................................. 27  
Adjusting the Tension of the Belt .................................................. 28  
Obtaining Service.......................................................................... 29  
page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before You Begin  
1
Thank you for purchasing the Precor M9.21i or M9.21si Low Impact Treadmill which  
feature several sophisticated and beneficial technologies: Ground Effects, Integrated Footplant  
Technology, Smart Rate®, and the Heart Rate Interactive System.  
Ground Effects allows the treadmill’s running bed to float” on specially formulated elastomeric  
springs which cushion impact and control lateral motion without diminishing the bed’s lively,  
responsive feel. Because it’s fully suspended, the bed provides optimum shock absorption  
anywhere your feet land, not just in the center of the running area.  
This manual explains how to assemble, use,  
and maintain the M9.21i or M9.21si Low  
Impact Treadmill. The following conventions  
are used in this manual:  
Integrated Footplant Technology (IFT) is a microprocessor-regulated motor control system. This  
patented technology collects motor and belt speed data, using it to monitor your workout and  
enhance your safety and comfort. It replicates the natural walking and running motion of your  
feet. By allowing slight, natural speed variations throughout your stride, Precor treadmills  
reduce shock and pounding to your body.  
Note:Contains additional information that  
applies to the preceding text.  
Important:” Indicates information to which you  
should pay special attention.  
CAUTION:” Indicates steps or information  
necessary to prevent harm to yourself or  
damage to the equipment.  
The console’s display offers varying selections that provide motivating feedback about your  
workout. The display also incorporates the latest in cardiac monitoring to provide Smart Rate® — a  
visual aid that lets you, the user, see your heart rate with a glance. On the M9.21i or M9.21si, the  
optional Precor receiver must be installed and the Precor Heart Rate Option chest strap worn,  
before the graph on the display can light up with colored cells to indicate your exercise intensity.  
WARNING:Provides instructions to prevent  
electrical damage to the equipment and prevent  
injuries to yourself or others.  
The M9.21i Low Impact Treadmill offers an easy-to-understand electronic console that gives  
motivating feedback about your workout. Professionally designed exercise options incorporate  
the latest in exercise science. Three different modes enhance your workout capabilities: Manual,  
Interval, Weight Loss, Random, and Heart Rate Control course which requires the Precor Heart  
Rate Option kit. The Heart Rate Course monitors your heart rate within a target zone (usually  
85% of your maximum heart rate) and automatically changes the incline to keep your heart rate  
in that zone when you wear the chest strap during your workout.  
DANGER:Indicates steps you must take to  
prevent electrical shock.  
The M9.21si combines all the benefits of the M9.21i and provides additional features: Program  
and Custom mode. The factory-programmed courses provide variety to help motivate you  
during your workout. A graphic representation of the programs appear on the console.  
The M9.21i and M9.21si Low Impact Treadmills are for household use only and have many  
unique features which sets them apart from conventional treadmills. To maximize your use of  
the M9.21i or M9.21si treadmill, please study this guide thoroughly.  
Unpacking the M9.21i or M9.21si Low Impact Treadmill  
CAUTION: This unit weighs over 160 pounds.  
To avoid injury and to ensure the safety of the  
unit and yourself, get adequate assistance  
before unpacking your treadmill. Slide the  
running bed out of the box.  
The M9.21i or M9.21si treadmill is carefully tested and inspected before shipment. Precor ships  
the unit in pieces, as listed below:  
running bed assembly  
upright column support assembly (includes the electronic console and upper handrail  
clamp)  
left and right handrails  
owner’s manual, limited warranty card, and hardware kit (The hardware kit is shown in  
Diagram 1.)  
Optional equipment that you can purchase through your dealer includes:  
Precor Heart Rate Option  
Precor Smart Weights  
Carefully unpack the pieces of the treadmill and lay them on the floor near the location  
where you plan to use the treadmill.  
page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 1  
A
B
C
Hardware Kit.  
F
G
H
I
D
E
J
K
L
After unpacking the treadmill, open the hardware kit (refer to Diagram 1) and make sure that you  
have the following items:  
(A) four frame-to-base plate bolts  
(B) two water bottle cage mounting bolts  
(C) two lower handrail clamp bolts  
(D) four split star washers—place on frame-to-base bolts  
(E) four internal star washers—2 for lower handrail clamps/2 for mounting water bottle cage  
(F) one 5/16" hex key—frame-to-base bolts  
(G) one 1/4" hex key—belt tracking and tension adjustment  
(H) one 3/16" hex key—upper handrail bolts  
( I ) one 5/32" hex key—lower handrail clamp and water bottle cage  
(J) two lower handrail clamps  
(K) one magnetic safety key assembly  
(L) one water bottle cage  
If any items are missing, contact the dealer from whom you purchased the treadmill or call  
1-800-4-PRECOR for the dealer nearest you.  
page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Low Impact Treadmill  
You do not need any special knowledge or experience to set up a M9.21i or M9.21si treadmill.  
However, you must review and follow the instructions in this manual. If you do not assemble and  
use the treadmill according to the following guidelines, you might void the Precor limited warranty.  
2
Installation Requirements  
Follow these installation requirements when installing the treadmill:  
Acquire the appropriate tools. In addition to the tools supplied in the hardware kit, you will  
need a phillips head screwdriver to remove the hood from the treadmill.  
Fill out and mail the limited warranty card. The serial number is printed on a label located  
underneath the treadmill on the left, rear corner of the running bed. Write the serial number  
onto the limited warranty card and in this manual before assembling the treadmill. Refer to  
Obtaining Service.  
Set up the M9.21i or M9.21si treadmill on a solid, flat surface. Do not install the treadmill  
on deeply padded, plush, or shag carpeting due to possible damage to the carpet and  
machine. If the treadmill is installed in a carpeted area, place a piece of heavy cardboard,  
plywood, or other solid, smooth, flat surface under the unit. If the floor is not even, the  
running belt will not track properly. Refer to Checking the Alignment of the Running Belt.  
Locate the treadmill at least 4 feet from walls and furniture. Be sure to provide ample space  
in front of the machine to allow easy access to the ON/OFF switch. Open space to the sides  
and back of the machine makes for a safer mount and dismount and easier belt adjustment.  
CAUTION: Do not remove or otherwise bypass  
the 3-prong plug with an adapter or extension  
cord in order to use a non-grounded outlet.  
Electrical damage can occur if the treadmill is  
connected to an improper power source.  
Use a standard 120-volt household outlet. The M9.21i or M9.21si treadmill is for household  
use only. Precor recommends plugging the treadmill into an outlet that is connected to a  
dedicated 20 amp house circuit breaker. A 20 amp circuit breaker inside the treadmill also  
helps protects the electrical and electronic components from sustained overloads. An integral  
3-prong, grounded plug meets safety requirements and protects the machine.  
Assembly Instructions  
To assist you in the assembly of the treadmill, the items in the hardware kit shown in Diagram 1,  
correspond to a particular letter in the alphabet. These letters appear throughout the assembly  
instructions. If necessary, refer to Diagram 1 while performing the steps below.  
To assemble the M9.21i or M9.21si treadmill, take the following steps:  
1. Locate the power switch at the front of the treadmill. Make sure that the power switch is in the  
OFF (O) position and unplug the treadmill’s power cord from the power outlet. Do not  
assemble the M9.21i or M9.21si treadmill if it is plugged into a power source.  
page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 2  
Remove the  
hood.  
Hood  
Screw  
Base  
Wheel  
2. Remove the treadmill’s hood using a phillips head screwdriver. Unscrew all six screws  
and set them aside. See Diagram 2. Grasp both sides of the hood with your hands and pull up  
to remove the hood from the base.  
Diagram 3  
Plug  
connector  
into lower  
board.  
Lower board  
P
R
E
C
O
R
P
R
E
C
O
R
Proper tab alignment on receptacle  
Lower board’s cables  
Front plate  
Ribbon cable connector  
Upright column support  
3. Set the upright column support assembly on the front plate. Route the ribbon cable under the  
lower board’s cables. See inset in Diagram 3.  
4. Align the tab on the ribbon cable connector with its counterpart located on the receptacle on  
the lower board. Plug the connector into the receptacle. See Diagram 3. The plastic flanges on  
the receptacle should clip onto the connector when you plug it in. Since the connector is  
designed to engage in one direction only, do not force the connector into the receptacle.  
5. Place a lock washer (D) onto each frame-to-base bolt (A). (The bolts and washers are found in  
the hardware kit.) Set the bolts and washers within easy reach of the upright column support.  
page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 4  
Secure the  
upright  
column  
support.  
Upright column  
Front plate  
Hex key (F)  
Frame-to-base bolt (A)  
Motor  
6. Secure the upright column support to the base by lifting it into position onto the base  
mounting plate. See Diagram 4. Align the bolt holes and hold onto the upright column support  
as you insert the frame-to-base bolts and finger tighten. Alternately tighten each bolt using the  
5/16" hex key (F) provided.  
7. With the upright column support secure, replace the hood by aligning the screw holes  
on the hood with the holes in the base frame. Tighten the screws securely using a phillips  
head screwdriver.  
8. Loosen the bolts in the upper handrail clamp using the 3/16" hex key (H). You do not need to  
remove the bolts.  
Diagram 5  
Secure the  
handrails  
into upper  
handrail  
clamp.  
Electronic console  
Handrail clamp  
Handrail clamp bolt  
Upper handrail  
9. Insert the upper end of a handrail into the upper handrail clamp. Using one hand, apply  
pressure on the portion of the handrail going into the clamp while, with the other hand, lift  
and lower the base of the handrail. This rotating motion helps move the handrail into place.  
The handrail is properly positioned when the black foam wrap touches the clamp as shown in  
Diagram 5. Repeat this step for the other handrail.  
Important: Do not fully tighten the upper handrail clamp bolts until you have installed the  
lower handrail clamps. The instructions are on the next page.  
page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 6  
Attachlowerhandrails.  
Handrail mounting hole  
Handrail  
Side rail  
Handrail nut plate  
Guide rail  
Base of treadmill  
Lower handrail clamp  
10. To mount the lower portion of the handrails, take the lower handrail clamps (J), two of the  
internal star washers (E), and lower handrail clamp bolts (C) out of the hardware kit. Refer to  
Diagram 6 while taking the following steps:  
Note: Perform these steps on one side of the treadmill before proceeding to the other side.  
a. Put one internal star washer (E) on each of the lower handrail clamp bolts (C). Place the  
bolts on either side of the treadmill near the location of the lower handrail.  
b. Place the lower handrail inside the lower handrail clamp (J). Slide the handrail nut plate  
along its guide rail until the hole in the nut plate is in line with the handrail clamp’s  
mounting hole.  
Diagram 7  
Secure the lower handrails.  
Deck  
Handrail  
Base and side rail assembly  
Nut plate  
Lower handrail clamp  
Bolt  
Lower handrail assembled  
c. Guide the lower handrail clamp onto the nut plate making sure that the flanges on the nut  
plate are inside the lower handrail clamp. See Diagram 7. Slide the clamp and nut plate  
along the guide rail to find the equilibrium point for the handrail.  
d. To secure the handrail inside the clamp, use the 5/32" hex key ( I ) provided. Do not  
overtighten the bolt or damage may occur to the clamp.  
Note: Periodically inspect the handrail clamp bolts and, if necessary, tighten the handrail  
clamp bolts using the 5/32" hex key ( I ) provided.  
e. Proceed to the other side of the treadmill and follow steps athrough d” to complete  
the installation of the lower handrails.  
page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 8  
Install the water  
bottlecage.  
Electronic console  
Water bottle cage  
Water bottle cage mounting location  
Bolt (B) with washer (E)  
Hex key ( I )  
11. Return to the upper handrail clamp, check to see that the foam on the handrails touches the  
edge of the clamp, readjust the handrails if necessary, and tighten the bolts securely using the  
3/16" hex key (H) provided.  
12. Install the water bottle cage by placing one internal star washer (E) on each of the mounting  
bolts (B). Position the cage onto the mounting hole locations and insert the bolts. See  
Diagram 8. Securely tighten the bolts using the 5/32" hex key ( I ). Place a water bottle inside  
the cage as shown in the inset in Diagram 8.  
13. Plug the treadmill into a standard 120v household outlet. Make sure that no other appliances  
use the same circuit as the treadmill. If you need to move the treadmill, ask for assistance  
from one or more persons. Roll the treadmill on its front wheels to the new location by lifting  
the rear end of the unit.  
Important: Before you can roll the treadmill on its front wheels, set the incline at 3% or more.  
Follow steps 1 through 4 in Checking the Alignment of the Running Belt, and then, adjust the  
incline to a minimum of 3%. Turn OFF the treadmill and unplug it before moving it.  
14. Continue on to Checking the Alignment of the Running Belt to complete the installation of the  
M9.21i or M9.21si treadmill.  
page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking the Alignment of the Running Belt  
The belt is aligned at the factory before shipment. However, during shipment or by using the  
treadmill on an uneven surface, the belt might move off center. Proper belt alignment is  
important because it allows the belt to remain centered and assures smooth operation. Take the  
following steps to check the alignment:  
1. Insert the magnetic safety key (K) into the opening on the electronic console. Locate the  
ON/OFF (I/O) switch at the front of the treadmill and turn ON (I) the treadmill.  
CAUTION: Do not walk on the running belt  
during this procedure.  
2. Stand beside the treadmill and press QUICK START. The running belt starts automatically  
after the display scrolls the message, Belt Starting 3, 2, 1,...”  
CAUTION: If you hear or notice any chafing or  
the running belt appears to be getting damaged,  
stop the running belt immediately by pressing  
the STOP key. Contact a Precor Service  
Representative.  
3. Continue standing next to the treadmill and press the SPEED key to maintain the running  
belt at a speed of 3 miles per hour (5 kph).  
4. Walk to the back of the treadmill and observe the belt for a few minutes as it moves.  
If the running belt,…  
Then,...  
tracks centered on the running surface  
the belt is functioning correctly and no  
adjustment is necessary.  
runs or drifts off center  
you need to adjust the belt; see Aligning the  
Running Belt in Chapter 7.  
Important: If you notice that the belt needs alignment, make the adjustments at once.  
Failure to do so might cause the belt to tear or fray which is not covered by the Precor  
limited warranty.  
5. To stop the running belt, press STOP and remove the safety key. Store the safety key in a  
safe place to prevent unauthorized use.  
If the belt is functioning correctly, the M9.21i or M9.21si treadmill is ready to use.  
page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Low Impact Treadmill  
3
As simple as using the M9.21i or M9.21si Low Impact Treadmill might seem, you should read this  
section so that you can use the treadmill safely and effectively. This section of the owner’s manual  
provides the basic information you need for exercising on your treadmill, including the following:  
locating the ON and OFF switch  
using the magnetic safety key  
reviewing features on the electronic console  
customizing the display (changing to U.S. standard or Metric,  
displaying Smart Rate, and selecting the TIME or DISTANCE prompt  
Note: Instructions explaining how to use the Precor Heart Rate Option and information regarding  
the Heart Rate Course appear in the next section: Using the Precor Heart Rate Option.  
Locating the ON and OFF Switch  
Use the ON/OFF (I/O) power switch to turn the treadmill ON I” or OFF O. This switch is located at  
the front of the treadmill, near the power cord.  
Note: The running belt will not move until the magnetic safety key is inserted into the electronic  
console. Refer to the instructions below for more information about the safety key.  
Using the Magnetic Safety Key  
CAUTION: Before each workout, always attach  
the magnetic safety key’s clip to your clothing  
at your waistline.  
The magnetic safety key lets you stop the treadmill’s running belt. Use this key in an emergency or  
when finished exercising. Pulling the key out of the console compartment has the same effect as  
pressing STOP. To prevent unauthorized use of the treadmill, store the safety key in a safe place.  
Diagram 9  
Magnetic safety key  
S
A
F
E
T
Y
K
E
Y
B
E
L
O
W
Magnetic safety key  
Before you can begin a workout, the magnetic safety key must be inserted into the electronic  
console as shown in Diagram 9. The treadmill’s running belt will not move until the safety key is  
inserted and secure inside the electronic console.  
Important: Do not force the safety key into position, it should slide easily into place within the  
electronic console compartment. Applying too much pressure to the connection could break a  
safety key component and void the Precor limited warranty.  
page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Understanding the Electronic Console  
The electronic console lets you control your M9.21i or M9.21si treadmill session. As you work out,  
the electronic display provides constant feedback about your progress. Information about distance  
covered, elapsed time, speed, total caloric burn, degree of incline, and heart rate (if you use the  
Precor Heart Rate Option) is available at any time. When you use the Precor Heart Rate Option, the  
chest strap that you wear transmits a signal which is picked up by the M9.21i or M9.21si software  
and displayed numerically (when the Heart Rate indicator is lit).  
The M9.21si also provides several preprogrammed courses and the ability to design your own  
custom courses (CUST1 or CUST2). For more information, refer to Creating Custom Courses on  
the M9.21si.  
Displays on the Electronic Console  
Indicator lights appear to show you which feature is being displayed. When you are working out,  
the electronic console display presents each feature consecutively—this is called scanning.  
Diagram 10 illustrates the electronic console display. Its features and keys are explained on the  
following pages.  
Diagram 10  
M9.21i electronic  
console display  
TM  
SMART RATE  
Above Zone  
Cardiovascular  
Weight Loss  
Below Zone  
Distance  
Time  
Speed  
Calories  
85%  
70%  
55%  
Incline  
Heart Rate Ð You must wear the Precor heart rate monitor to activate the Heart Rate display.  
Scan  
PROGRAMMED COURSES  
Manual Change speed / incline to vary your workout  
Interval Course  
Weight Loss Course*  
CAUTION  
¥
¥
¥
¥
¥
¥
¥
¥
Keep hands and clothing away from bed, belt, and rear roller when the treadmill is in operation.  
Do not allow children and people unfamiliar with treadmill operation on or near the treadmill.  
Never stand on the belt when starting the treadmill. Stand with your feet on the side platforms.  
mph and slower.  
1
2
3
4
5
Ð
Ð
Alternating rest and work intervals maximize aerobic conditioning.  
Never attempt to turn around on the moving belt. Step onto the belt only at speeds  
Read owner's manual before operating this treadmill.  
complete physical examination by your physician.  
1
Ð
28 minute program maximizes caloric burn.  
Before beginning any fitness program, you should have  
a
Based on research at the Cooper Institute for Aerobics Research.  
Consult your physician for the heart rate appropriate for your fitness level.  
If you feel faint or dizzy, stop exercising immediately.  
Heart Rate Course* Maintains heart rate within your target zone by increasing/decreasing incline.  
Ð
WARNING: Remove safety key when not in use and store out of reach of children.  
Random Course  
Ð
Presents  
a
different hill profile each time.  
Precor heart rate monitor required for these courses.  
*
©1997 Precor Incorporated  
INCLINE  
SPEED  
ENTER  
QUICKSTART  
CHANGE  
Hold to Reset  
STOP  
Note: Informative messages scroll across the display and prompt you to enter specific information  
before a workout. These messages request information and action, or explain problems that may  
arise while you are using the treadmill. Some problems you can solve. Other problems may require  
a qualified service technician. If you are unsure about an error message, please call a Precor  
authorized service center. For the service center nearest you call, 1-800-4-PRECOR.  
SMART RATE:® When the optional Precor heart rate receiver has been properly installed in the  
treadmill and you wear the Precor Heart Rate Option’s chest strap, a blinking segment in the bar  
graph appears on the left of the display. If you have entered your age (completed during the setup  
prompts), the blinking segment shows you the zone that your heart rate is in: either Weight Loss or  
Cardiovascular.  
Important: Smart Rate and HEART RATE displays only appear when the Precor heart rate receiver  
is installed in the electronic display and the chest strap transmitter is worn. Smart Rate does not  
appear when you use the Quick Start key. If the Smart Rate segment appears, but does not blink, it  
means that a receiver is installed, but that you are not wearing the chest strap transmitter or it is  
not working properly. To correct transmitter problems, refer to your Precor Heart Rate Option  
Owner’s Manual or to Obtaining Service in this manual.  
DISTANCE: The distance you have travelled appears once you begin a workout. Distance can  
appear in miles or kilometers. If you wish to change the display, you can follow the instructions  
found in Customizing the Display.  
TIME: During your workout, a time (00:00) display appears automatically and stops whenever you  
pause or stop the running belt. As you work out, you will notice that the time starts at zero and  
counts up when you use distance-based courses. It counts down when in the timed courses and  
alternates between counting up and counting down during the Interval and Weight Loss programs.  
Time appears in minutes and seconds. However, should you exceed 60 minutes (during a single  
workout), the time display converts to hours and minutes.  
page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEED: The speed at which you are travelling appears in this display. Your speed can appear in  
miles per hour (0.5 to 10 mph) or kilometers per hour (0.8 to 16 kph). If you wish to change the  
display, you can follow the instructions found in Customizing the Display.  
CALORIES: When you enter your accurate weight, the number of calories you are burning while  
you workout appears in the display. At the end of the workout, the estimated number of calories  
burned appears in the display. The calorie calculation is dependent on the weight that you enter  
during the setup prompts. An accurate weight selection results in a more accurate calorie count.  
Note: If you press the QUICK START key, the calorie count is based on a 150 lbs (68 kg) person.  
INCLINE: The M9.21i or M9.21si treadmill provides inclines from 0% to 15%. You can change the  
incline and decrease or increase the level of your workout by pressing the INCLINE keys.  
HEART RATE: The heart rate display lets you monitor your heart rate and, in the Heart Rate  
Course (HRC), keeps you within your training zone. You must purchase the Precor Heart Rate  
Option and wear the chest strap transmitter before your heart rate can appear on the display. For  
more information, refer to the section titled Using the Precor Heart Rate Option.  
SCAN: When you are working out and the display is in SCAN mode, an indicator light appears  
next to the word SCAN. Another indicator light appears next to the feature that is being dis-  
played. About every 30 seconds, the indicator light moves sequentially through each field on the  
display.  
The SCAN indicator can only be highlighted in Manual mode. In any other program, scanning  
occurs automatically. To stop scanning and display one feature, press the CHANGE key. Continue  
to press the CHANGE key to move the indicator light to the feature you want displayed.  
Keys on the Electronic Console  
Each key on the electronic console’s keypad provides specific functions. The following information  
explains the different uses of the keys from left to right. To locate each key, look at the electronic  
console or refer to Diagram 10.  
ENTER: When you turn ON the treadmill, several prompts appear before you start your workout.  
Each prompt needs to be addressed and then entered” into the treadmill’s memory by pressing  
the ENTER key.  
Note: Tapping ENTER successively 3 times when the start-up prompt ENTER WEIGHTappears  
on the display causes the treadmill to retrieve the last workout program from memory and display  
it. Refer to Retrieving the Previous Workout Program.  
INCLINE CONTROL : The INCLINE arrow keys let you decrease or increase the  
treadmill’s incline settings from 0% to 15% in Manual mode.  
STOP: To pause during your workout, press the STOP key. The running belt stops and the  
displays on the console freeze allowing you to review your workout statistics. See Pausing Your  
Workout. Tapping STOP twice during a workout program causes the treadmill to access the  
Manual mode. Use this feature to incorporate a cool-down period into your workout. See Cooling  
Down After a Workout.  
HOLD TO RESET: To exit the Manual and Interval programs, press HOLD TO RESET for a few  
seconds. The displays clear, your workout statistics are saved and added to the cumulative totals.  
Continue to press HOLD TO RESET and the Precor banner appears on the display. You can also use  
this key to exit other courses prematurely. See Ending Your Workout.  
SPEED CONTROL : The SPEED arrow keys let you decrease or increase the treadmill’s  
speed settings. During a workout, you can decrease or increase the speed of your workout from  
0.5 to 10 miles per hour or 0.8 to 16 kilometers per hour. You can also use the SPEED key to  
slow the running belt to a gradual stop.  
QUICK START: Pressing QUICK START at the Precor banner or during the setup prompts causes  
a “Belt Starting 3, 2, 1,...” message to scroll across the display. The running belt begins  
moving at 1 mph and the treadmill enters Manual mode. A default weight of 150 lbs (68 kg) is  
used to calculate the total caloric burn. (For more information, refer to Using the QUICK START  
Feature and Using the Manual Course Mode.  
page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGE: In Manual mode, the CHANGE key lets you select the feature that you want to appear on  
the display. The feature remains displayed until you press CHANGE again. In other programs,  
pressing the CHANGE key activates the scan function. Starting from the top of the display, each  
feature is displayed sequentially and then, the course profile reappears. Note that HEART RATE  
only appears if you are using the Precor Heart Rate Option.  
Customizing the Display  
The M9.21i or M9.21si treadmill can display speed in either miles per hour (mph) or kilometers  
per hour (kph) and distance in miles or kilometers. When the M9.21i or M9.21si is shipped from  
the factory, it is set to display to U.S. Standard units of measure (mph and miles). You can also  
choose to turn the Smart Rate display on or off and change whether the TIME or DISTANCE  
prompt appears after you choose a preprogrammed course. You can easily change an of the  
settings by taking the following steps:  
Note: The M9.21i or M9.21si treadmill will retain your selection even when it is turned OFF and  
unplugged. You can change your selection at any time by repeating the following steps.  
1. Insert the magnetic safety key into the electronic console.  
2. Turn ON the treadmill using the power switch located at the front of the hood.  
3. At the Precor banner, press the STOP key, followed immediately by the QUICK START key,  
then the SPEED key, and lastly the SPEED key. (The numbers 3, 4, 5, 6 appear  
sequentially on the display as you press the associated key.) The prompt, PRESS FOR  
MPH OR FOR KPHappears on the display.  
Important: If the QUICK START key is not pressed within 1 second after pressing the STOP  
key, the display returns to the Precor banner. You will need to begin again.  
4. Any or key lets you alternate between the prompts. Press one of the or keys.  
5. A prompt SMART” or NO SRappears on the display. Anyor key lets you alternate  
between the prompts to select whether you want the Smart Rate display to appear (SMART)  
or not appear (NO SR) on the display.  
6. Two messages scroll across the display: one confirms your mph or kph selection and the  
other states, PUSH FOR DISTANCE OR FOR TIME OR RESET’ TO ASK.Press the  
appropriate key after answering one of the following if/then scenarios:  
Note: When using a preprogrammed course (M9.21si only), you can measure your workout  
by distance or time. You see the SELECT DISTANCE” or SELECT TIME” prompt after you  
enter a course selection. The default measurement is distance.  
Ifyouwant,...  
Then,...  
your workout measured by distance  
press the key  
your workout measured by time  
press the key  
the option of selecting time or  
distance prior to each workout  
press HOLD TO RESET (STOP)  
After you press an arrow key, a message scrolls across the display  
confirming your selection.  
7. The changes have been retained in the treadmill’s memory. Continue with your workout or  
turn OFF the treadmill. If you turn OFF the treadmill, be sure to store the safety key in a safe  
place to prevent unauthorized use.  
page 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Working Out on the Low Impact Treadmill  
4
Before using your treadmill, we recommend that you follow these instructions and go through a  
preliminary demonstration of the treadmill.  
When using the treadmill, follow these general guidelines:  
At the beginning of a workout, take several minutes to bring your heart rate into your training  
zone, shown in Diagram 15 in Chapter 6.  
After your workout, walk slowly for several minutes to cool down your body and lower your  
heart rate. Use the cool-down feature on your treadmill.  
Using the clip provided, attach the magnetic safety key to your clothing at your waistline  
before each workout. Then, if you encounter difficulties or want to end your workout, you can  
easily stop the running belt by pulling on the cord.  
Before and after a workout, gently stretch your lower body and back to help prevent stiffness  
or soreness.  
A variety of exercise options are available on the M9.21i or M9.21si. The course profiles on the  
M9.21i (refer to the label on the electronic console) provide workouts from manual mode to  
preprogrammed, customized courses, and heart rate interactive courses. (To use the Smart Rate  
and Heart Rate features, you will need to purchase the Precor Heart Rate Option.)  
Quick Steps to Working Out  
To work out on the M9.21i or M9.21si, take the following steps:  
1
Put on chest strap (optional).  
1. For Smart Rate or your HEART RATE to appear on the display, the heart rate receiver must be  
installed in the electronic console display and you need to wear the chest strap transmitter.  
Refer to Wearing the Chest Strap Transmitter to learn how to properly use the chest strap.  
2
3
Insert Safety Key.  
Turn ON treadmill.  
2. Insert the magnetic safety key into the electronic console compartment.  
3. Locate the ON/OFF (I/O) switch at the front of the treadmill and turn ON the treadmill. The  
Precor banner scrolls across the electronic console display.  
page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
5
Straddlebelt.  
4. Straddle the running belt with your feet firmly planted on the right and left staging platforms.  
(Stand close enough to the electronic console so that you can extend your arms to easily  
touch the keys.)  
Attach safety clip to clothing.  
5. Using the clip provided, securely attach the magnetic safety key to your clothing near your  
waistline where it will not interfere with your workout.  
Important: To retrieve the last course used, rapidly tap the ENTER key three times. Or, to  
display the manual mode’s course profile, press QUICK START. When you use QUICK START,  
a default weight of 150 lbs (68 kg) is used for calculating the CALORIES display. Refer to  
Using the QUICK START Feature.  
6
Enter Weight or press Quick Start.  
6. If you do not use QUICK START or retrieve the last course or program, press any or key  
to change the weight. (The weight increases and decreases in 5-pound or 2 kg increments) To  
increase the accuracy of the calorie count that appears on the display, select a weight that is  
closest to your actual weight. Press ENTER.  
7
8
Enter AGE.  
7. The AGE prompt appears if the Precor Heart Rate Option receiver is installed in the  
electronic console display. If you wish to purchase this valuable option package, contact the  
dealer nearest you by calling, 1-800-4-PRECOR.  
Select Course.  
8. At the SELECT COURSE” prompt, choose your workout mode:  
M9.21i  
Manual (MAN’L), Interval (INTV), Weight Loss (WT.LS.),  
Heart Rate Course (HRC) or Random  
Important: Before working out, review the  
information regarding the different  
M9.21si — all the programs mentioned above plus the preprogrammed courses shown on  
the display label.  
M9.21i or M9.21si programs and their  
operation. Refer to pages 15 through 22.  
Press the or key until you see the desired mode or course number appear on the  
display, then press ENTER.  
9
Start working out.  
9. Depending on the program you select, you may be prompted to answer more questions or  
press the SPEED key to begin your workout. Hold onto the handrail with one hand while  
you press SPEED with the other hand. Step onto the running belt while the speed is at or  
below 1 mph (1.6 kph). Once you are comfortable with the walking or running speed, you  
can remove your hands from the handrail.  
Use the optional Smart Rate and  
Heart Rate displays to keep your  
heart rate in your target zone:  
cardiovascular or weight loss.  
(Pause)  
To pause during your workout session before finishing the selected program, press the  
STOP key. The displays on the console freeze. See Pausing Your Workout or Ending Your  
Workout for more information.  
To purchase the Precor Heart  
Rate Option or Smart Weights,  
call your local dealer.  
Note: Optional hand weights, called Precor Smart Weights, are available from your local  
dealer. Precor Smart Weights provide 1- or 2-pound hand weights with the added conve-  
nience of remote control. The remote control lets you change your speed or incline and stop  
the running belt. Precor Smart Weights give you control of your treadmill’s electronic console  
functions while you enjoy the added benefit of an upper body workout. For more information  
call your local dealer. To locate the dealer nearest you call, 1-800-4-PRECOR.  
10  
End workout.  
10. When you are finished exercising, hold onto the handrail and press STOP. (You can also  
press SPEEDuntil the running belt stops.) You can then review your workout results as  
the display scans through DISTANCE, TIME, and CALORIES. (HEART RATE appears if you  
are wearing the Precor chest strap.)  
(Cool down)  
Note: Always allow yourself a cool-down period of a few minutes before bringing the running  
belt to a complete stop. Cooling down after your workout helps reduce muscle stiffness and  
soreness by transporting excess lactic acid out of the working muscles. It also helps your  
heart rate return to its normal (non-exercising) state. You can access the manual mode  
(MAN’L) from any program by tapping STOP twice in quick succession. Manual mode enables  
you to change the speed and incline and adapt a cool-down period into your workout.  
11  
12  
13  
Review workout statistics.  
11. If desired, after reviewing the displays, reset them to zero by pressing HOLD TO RESET for  
several seconds.  
(Press HOLD TO RESET)  
Remove Safety Key. Turn OFF the  
treadmill.  
12. Detach the safety clip from your clothing and remove the magnetic safety key from the  
electronic console. Turn OFF the treadmill.  
Store Safety Key in a secure place.  
13. To prevent unauthorized use, store the safety key in a safe place.  
page 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the QUICK START™ Feature  
CAUTION: Hold onto the handrails when you  
press QUICK START. The running belt starts  
automatically at 1 mph after the display scrolls  
the message Belt Starting 3, 2, 1,..”  
The words quick start” imply that you can start your workout immediately. Once you insert the  
magnetic safety key and attach the safety clip to your clothing, the QUICK START feature on the  
M9.21i or M9.21si treadmill allows you to bypass the setup prompts and access manual mode. The  
weight setting defaults to 150 pounds (68 kg) so all calorie calculations and their associated  
displays are based on a body weight of 150 pounds (68 kg). The Smart Rate display will not work  
when you use the QUICK START key.  
Note: Any prompts that appear after the SELECT COURSE” prompt require your input before you  
can proceed. You can press QUICK START at any prompt and access manual mode features.  
However, QUICK START is disabled once you enter a program and begin your workout.  
Retrieving the Previous Workout Program  
To retrieve the previous workout program, simply tap the ENTER key successively three times  
while the prompt ENTER WEIGHT” is being displayed. Note that if someone else has exercised on  
the treadmill after your workout, whatever program he or she used will be the one that is restored  
from memory.  
Pausing Your Workout  
You can pause at any time during your workout. Use this feature to rest or take a short break. To  
pause while working out, press the STOP key. The running belt stops. Remove the safety key clip  
and straddle the running belt so that you can safely step off the treadmill. Your workout statistics  
freeze and remain displayed on the console until you resume your workout.  
Do not rely on the Pause feature as a way to end your workout. If you wish to end your workout,  
follow the instructions in Ending Your Workout.  
To resume your workout, straddle the running belt, attach the safety key clip to your clothing,  
press the SPEED key to start the running belt, hold the handrail, and step onto the running belt  
while the speed is at or below 1 mph. Your workout statistics continue from where you left off.  
Continue to press the SPEED key, to increase the speed to a comfortable level. Once you are  
comfortable with the walking or running speed, you can remove your hands from the handrail.  
Cooling Down After a Workout  
Cooling down after your workout is important because it helps reduce muscle stiffness and  
soreness by transporting excess lactic acid out of the working muscles. Cooling down for at least  
3 minutes helps provide a smooth transition that allows your heart rate to return to its normal  
(non-exercising) state.  
You can cool down after a workout by accessing Manual mode (MAN’L). Tapping STOP twice in  
quick succession accesses MAN’L mode from the preprogrammed courses (M9.21si only).  
Ending Your Workout  
To end your workout, take the following steps:  
1. Hold onto the handrail and press the STOP key or press the SPEED key until the running  
belt slows to a gradual stop. The displays on the console freeze which lets you review your  
workout statistics.  
2. Continue to press STOP (HOLD TO RESET) for a few more seconds to add your workout  
statistics to the cumulative totals and return to the Precor banner.  
3. Straddle the running belt and step off the treadmill.  
4. To prevent unauthorized use, remove the magnetic safety key from inside the electronic  
console and store it in a safe place. Turn OFF the treadmill.  
page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Interval Course Profile  
Interval training provides numerous benefits. Since interval training segments the workout into  
smaller components, a 20- or 30-minute workout seems to pass more quickly. In addition, studies  
have shown that it is a more efficient method for achieving aerobic benefits—you start seeing  
improved cardiovascular fitness much sooner with less effort. Studies also show that people who  
interval train are more likely to stick with their fitness program.  
The interval course on the M9.21i or M9.21si treadmill lets you set the course intervals according  
to your training regimen. It alternates between 60 seconds of Restand 60 seconds of Work.”  
During the Rest interval, you can walk or jog slowly; during the Work interval, you can stride  
quickly or run. You set the speed and incline for the first rest and work interval and the software  
takes over from there, repeating the intervals throughout the course until you press the STOP key.  
At any point during the workout, you can change the speed and incline of the current interval. For  
example, if 8 mph is a little faster than you prefer during a Work interval, simply use the SPEED ▼  
key to reduce speed. The software remembers the new speed for the next Work interval.  
If you have purchased the Precor Heart Rate Option and installed the heart rate receiver, you can  
monitor your workout using the Smart Rate and HEART RATE displays.  
Note: If you pause your workout during an Interval mode, you must reset the speed of the mode  
you were in when you paused your workout. For example, if you paused your workout during the  
Rest interval, you must reset the speed for that interval. In this example, you would not need to  
reset the speed for the Work interval since it is stilled stored in memory.  
Below are some suggestions that may help you incorporate the Interval mode into your workout:  
If you are starting an exercise program, the Interval mode option can help you increase your  
workload gradually. For example, in the beginning, you may simply want to specify the same  
speed and incline for both Work and Rest intervals. Then, to increase your effort level, change  
to a higher speed and/or incline for your Work interval.  
If you are training with the goal of maintaining a constant pace when on level ground or grade,  
specify the same speed for both Work and Rest intervals. Then, gradually increase the incline  
during the Work interval until you can maintain a constant pace.  
To use the interval course, follow the steps in Working Out on Your M9.21i or M9.21si Treadmill.  
At the “SELECT COURSE” prompt, use the keys to display INTV,” and press ENTER.  
To set the interval for the course, take the following steps:  
1. When you see ENTER REST SPEED & INCLINE” scroll across the display, stand on the  
running belt with one hand on the handrail, prepared to start walking. With your other hand,  
press the SPEED key until you reach a comfortable rest speed, either running or walking.  
Press the INCLINEor key to specify an appropriate incline. When the desired speed  
and incline are displayed, simply continue working out—you do not need to press ENTER.  
Once you reach your desired rest speed and incline, the treadmill returns to it at the  
beginning of each rest interval, until you change the speed or incline, or end your workout.  
2. When ENTER WORK SPEED & INCLINE” scrolls across the display, specify your work  
speed (up to 10 mph). With one hand on the handrail, use the other hand to press the  
SPEED or keys until the desired work speed is shown. Use the INCLINEor key to  
set the incline. When you are comfortable with the rest and work speeds and inclines, you  
can let go of the handrail.  
Each rest and work interval lasts 60 seconds. The display automatically counts down to the next  
interval. When the count reaches 30 seconds, the display changes and gives information about  
distance travelled, time elapsed, speed, calories burned, and percent of incline.  
When the treadmill changes intervals, it informs you by scrolling GOING TO REST SPEED” or  
GOING TO WORK SPEEDacross the display.  
Using the interval course mode, you can cool down before ending your workout by pressing STOP  
twice in quick succession. The treadmill enters Manual Mode, letting you specify the speed of your  
cool-down period.  
page 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Weight Loss Program  
The Precor Weight Loss Program incorporates the latest findings on fat-burning and weight loss  
through exercise. It is based on research at the world-renowned Cooper Institute for Aerobics  
Research.  
CAUTION: Before beginning any fitness  
program, you should obtain a complete  
physical examination from your personal  
physician.  
The Weight Loss Program is similar to the interval course program on your M9.21i or M9.21si  
treadmill. The Weight Loss Program provides a 28-minute workout with inclines preset to a  
minimum level for the 4-minute rest interval and a maximum level for the 4-minute work interval.  
You can adjust the incline during any interval segment. However, changing the incline will reduce  
the effectiveness of your weight loss program. Any time you adjust the incline, the software returns  
to the default incline of minimum or maximum at the beginning of the next rest or work interval.  
The treadmill alerts you of upcoming incline or interval changes by scrolling messages across the  
display.  
The Weight Loss Program is designed to help you burn the most fat during a 28-minute workout,  
while minimizing the risk of discomfort and injury. Performed three or four times a week, the weight  
loss mode will help you reach your ideal weight and fitness level quickly and efficiently.  
CAUTION: The treadmill may automatically  
change incline when you enter a program. Stay  
clear of the lift mechanism and hood area until  
the treadmill has completed the recalibration  
process.  
To use the Weight Loss mode, follow the steps found in the section titled Working Out on Your  
M9.21i or M9.21si Treadmill. When the electronic console display prompts you to select a course,  
use theor keys to select WT.LS.and then, press ENTER.  
Note: Be sure to enter your correct weight at the weight prompt. Deviating from your actual  
weight reduces the effectiveness of the weight loss program.  
Table 1  
Perceived Level of Fitness  
Speed calculated  
in mph & kph  
7.3 High  
7
6
5.8 Medium High  
5
5.0  
Medium  
4.5 High  
4
3
2
1
3.6 Medium High  
3.5  
Medium Low  
3.1  
Medium  
2.2  
Medium Low  
2.1 Low  
1.3 Low  
KPH  
MPH  
Set the speed of the treadmill based on your perceived level of fitness (low, medium, or high—  
see Table 1). The incline is preset to accommodate your level of fitness.  
CAUTION: If you are unsure about your level of  
fitness, start at the low speed. Do not increase  
your speed beyond 1.3 mph or 2.1 kph.  
Remember, always consult your physician  
before beginning any new exercise routine.  
If you wish to continue the weight loss program at the end of the 28-minute period, press the  
SPEED. The speed remains constant and the preset 4-minute rest and work intervals continue to  
repeat until you press the STOP key. If you want to adjust the speed, press the SPEEDor key  
until the desired speed appears in the display.  
Always monitor your pulse during and at the end of your workout. If you purchased the Precor  
Heart Rate Option and have installed the receiver and are wearing chest strap, you can monitor  
your heart rate through the Smart Rate and HEART RATE displays. For the ideal weight loss”  
range, your heart rate should be between 55% and 70% of your maximum aerobic heart rate. It  
should never exceed 80% of your maximum aerobic heart rate or go above your training zone.  
Refer to Diagram 15 in Getting the Most Out of Your Workout for your appropriate training zone.  
Important: If you use the Precor Heart Rate Option, you can adjust the rest or work intervals if your  
heart rate is above or below the recommended zones for your age. For the Weight Loss course, try  
to maintain your heart rate at the lower end (55% of maximum heart rate) while in the rest”  
intervals and keep it at 70% of maximum heart rate while in the work” intervals.  
page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Manual Course Program  
CAUTION: Hold onto the handrails when you  
press QUICK START. The running belt starts  
automatically at 1 mph after the display scrolls  
the message Belt Starting 3, 2, 1,..”.  
Manual mode lets you use the M9.21i or M9.21si treadmill for an indefinite period of time while  
controlling the speed and incline.  
You can choose the Manual course program in two different ways:  
pressing QUICK START at the Precor banner or any set-up prompt displays the manual course  
profile. The weight setting defaults to 150 pounds (68 kg) so all calorie calculations and their  
associated displays are based on a body weight of 150 pounds (68 kg). The Smart Rate  
displays do not work when you use QUICK START. For more information, refer to Using the  
QUICK START Feature.  
entering your weight and selecting the MANL” course. At your next workout (if no one else  
has used the treadmill), rapidly tap ENTER three times to access this same program.  
When you choose the Manual program, the program’s course profile appears in the display and  
shows a flat constant course. The INCLINEor keys change the incline and the SPEEDor ▲  
keys affect the speed of the running belt.  
Important: To end a workout in Manual mode, you need to press STOP or press the SPEED ▼  
key until the running belt stops. Press HOLD TO RESET for a few seconds to clear the display.  
Using the Random Course  
Choosing a random course provides variable course profiles. Each course profile is randomly”  
selected by the M9.21i or M9.21si software. Every time the Random course is selected, a different  
course profile appears.  
Using a Preprogrammed Course on the M9.21si  
CAUTION: If this is the first time you have  
operated this treadmill, DO NOT STAND on the  
running belt until you become familiar with  
treadmill’s operation. Be sure to read and follow  
the general guidelines found in Working Out  
on Your M9.21 or M9.21s Treadmill” prior to  
using the treadmill.  
To use a preprogrammed course, follow the instructions below. Remember, when you use the  
electronic console, hold onto the handrail to maintain your balance. You should also use the  
handrail whenever you speed up, slow down, or stop the treadmill.  
The M9.21si is equipped with six preprogrammed courses and two custom courses that vary in  
distance, time, and incline. Refer to the label on the electronic console for a representation of the  
course profiles.  
To use the preprogrammed courses, follow the steps in Working Out on the M9.21i or M9.21si  
Low Impact Treadmill and add the following variation.  
CAUTION: The treadmill may automatically  
change incline when you enter a program. Stay  
clear of the lift mechanism and hood area until  
the treadmill has completed its recalibration.  
1. At the SELECT COURSE” prompt, enter a program name WALK” or RUN.”  
The WALK courses combine .05-mile segments with a set series of inclines. The RUN courses  
combines .1 mile segments. The percent of incline and the frequency with which inclines are  
encountered indicate the difficulty of the course. For example, WALK EASY takes the user  
through inclines ranging from 0 to 3 percent grade, while RUN ADV uses inclines in the  
minimum to maximum range on a more frequent basis. The software simply repeats the  
segments until the distance or time limit you set is reached, or you press the STOP key.  
Note: If you do not press ENTER to select a course, after 10 seconds the prompt PRESS  
ENTER TO BEGINappears. This prompt continues to scroll across the display every few  
seconds until ENTER is pressed.  
2. At the SELECT MILES (kilometers)” prompt specify the length of your course. Press the  
or keys to choose distance. Press ENTER when the desired distance appears.  
Note: You can change the SELECT MILES” prompt to SELECT TIME” if you prefer to  
measure your workout by distance. Follow the procedure in Customizing the Display.  
If you see SELECT TIME” scroll across the display, specify the length of your workout. Press  
theor key to choose time; the display moves in 1-minute increments, from 5 to 50  
minutes. Press ENTER when the desired time appears.  
page 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Creating Custom Courses on the M9.21si  
You can program the M9.21si and create your own course profiles using the two custom  
courses (CUST1and CUST2”). Programming a custom course is easy. You just create the  
custom courses as you work out by determining the speed and incline for each 0.1 mile segment  
along the 8-mile maximum course length. Speed and incline settings are saved once every .1 of a  
mile which equals 10 dots on the display. Once you complete your workout, the course is stored  
in memory and can be automatically recalled using the same program number.  
To create a custom course, follow the steps in Working Out on the M9.21i or M9.21si Low  
Impact Treadmill and add the following variation.  
1. At the SELECT COURSE” prompt, choose your custom course: either CUST 1” or CUST 2.”  
Press the or keys until you see the desired course, then press ENTER.  
Note: After pressing ENTER, a prompt scrolls across the display warning you that the  
custom course contains set speed and inclines. You are not to use the course if you are not  
familiar with it. The following instructions assume that you are programming a new custom  
course. However, if you want to use the existing custom course, press SPEED to begin.  
CAUTION: After pressing ENTER, clear an  
existing custom course profile by simulta-  
neously pressing both the INCLINE keys  
for at least 3 seconds. The course profile  
reverts to a blinking line at 0% incline. Be  
cautious about performing this procedure.  
Once you clear an existing course profile, you  
cannot retrieve it.  
2. Hold onto the handrail and press the SPEED key. Step onto the running belt while the  
speed is at or below 1 mph and begin walking. Use the INCLINEkeys to change the  
course profile as you walk. The first time the custom courses appear, the profile appears  
flat (0% incline) until you change it.  
3. As you move through the course, you can change the course profile by using the SPEED  
and INCLINE keys on the segment that is blinking. You cannot go back” to a segment  
once you move beyond it. However, you can pause by pressing STOP. Prompts appear and  
scroll across the display asking you to save the course and end your workout, or continue  
with your workout.  
Pressing ENTER saves the course profile up to the point (mile or kilometer) where you  
stopped and resets any previously saved program course.  
Note: You must program at least .10 mile (10 dots on the display) before your new  
course can be saved otherwise the software reverts back to the existing course. If an  
existing course profile extended beyond the segment where you stopped, it will be  
discarded.  
Pressing SPEED starts the running belt and allows you to continue from where you  
left off. Be sure to hold onto the handrail before pressing SPEED .  
4. Once you reach the maximum distance of 8 miles, the prompt, END COURSEappears and  
scrolls across the display. The running belt slows to a gradual stop, the incline returns to 0%,  
and prompts appear requesting that you save your changes.  
5. Save your changes by pressing ENTER. Once you save your custom course, you can work out  
and use the same course over and over by entering the associated custom course number.  
Deleting Custom Courses on the M9.21si  
An existing custom course can be deleted by pressing both INCLINE or keys when the  
custom course profile appears on the display. Take the following steps to delete a custom course:  
CAUTION: Once you press the INCLINE ▲  
keys to reset the course profile, you cannot  
retrieve the old custom course.  
1. After answering the setup prompts and choosing your custom course, a CAUTION”  
message scrolls across the screen indicating that an existing custom course exists.  
2. When the course profile appears on the display, press both INCLINE keys and hold for  
at least 3 seconds. A message appears indicating that the custom course profile has been  
reset (0% incline and 1 mph/kph speed).  
page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Precor Heart Rate Option  
5
The Precor Heart Rate Interactive System has many unique features. When you use the Precor Heart  
Rate Option and have the optional heart rate receiver installed in the electronic console, your heart  
rate can appear on the display. The Smart Rate and Heart Rate displays simplify the correlation  
between heart rate and exercise. You don’t have to stop concentrating on your workout to find your  
pulse anymore. It is displayed right in front of you. When you use the Heart Rate Course, the software  
monitors and maintains your heart rate in the target zone best suited for your specific needs.  
When you maintain your heart rate between 70% and 85% of your maximum aerobic heart  
rate, you are improving your overall cardiovascular/cardiorespiratory fitness level. If you maintain  
your heart rate between 55% and 70% of your maximum aerobic heart rate, you are burning  
enough calories that, when continued on a regular basis for 30 minutes or more, provides the  
greatest fat-burning (weight loss) benefits. Before you use the chest strap transmitter, Heart Rate  
Course, or Weight Loss program, please study this section thoroughly. Included in this section are  
the following:  
wearing the chest strap transmitter  
using the Heart Rate Course  
utilizing the heart rate interactive system  
correcting inconsistent heart rate readings  
Important: If you do not use the Precor Heart Rate Option and the optional heart rate receiver  
according to the guidelines found in this manual, you could jeopardize the accuracy of your heart  
rate readings or void the Precor limited warranty.  
Wearing the Chest Strap Transmitter  
The Precor Heart Rate Option is a completely wireless system. A built-in receiver displays continual  
feedback about your heart rate when you wear the transmitter strap around your chest. No bulky  
wires or cables interfere with your movements.  
The wireless chest strap contains the electrodes that transmit your heart rate (pulse) to the  
receiver. To get an accurate reading, the electrodes need to be moist and in direct contact with  
your skin. Be sure to wear the chest strap underneath your clothing.  
Take the following steps to put on the chest strap:  
Diagram 11  
Determine proper  
length.  
1. Determine the length of the strap by wrapping it around  
your chest. Without stretching the strap, check the  
distance between the two ends of the strap. For a snug fit,  
the ends of the strap should be about 6 inches (15 cm)  
apart. See Diagram 11. Adjust the tightness of the chest  
6 in.  
(15 cm)  
strap by sliding the buckle along the strap.  
2. Remove the strap from around your chest and dampen the  
electrode strips with tap water as shown in Diagram 12 or  
use the Precor spray. Do not use deionized water. To  
function properly, the electrodes need the salts and minerals  
found in non-purified water. Once you begin your workout,  
your perspiration keeps the electrodes moist.  
Diagram 12  
Moisten electrodes.  
If needed, use the  
spray included with  
the Precor Heart  
Rate Option.  
3. Buckle the strap around your chest. The strap should feel  
snug, not restrictive. Make sure that the transmitter lies  
horizontally across your chest and is centered in the middle  
of your chest. See Diagram 13.  
Diagram 13  
Buckle chest strap.  
Note: The chest strap transmitter has a one-year warranty.  
Some units contain a replaceable battery. To change the  
battery, refer to Changing the Battery in the Chest Strap on  
page 32.  
With the proper adjustment of the  
chest strap, you are ready to begin using  
the Precor Heart Rate Option.  
page 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Utilizing the Heart Rate Interactive Capabilities  
You can make each program on the treadmill a heart rate interactive course by monitoring and  
maintaining your heart rate in the Smart Rate® zone best suited for your specific needs. You can  
access Smart Rate only if the optional heart rate receiver is installed in your unit and you wear the  
Precor chest strap. The Smart Rate indicator lights do not appear when you use QUICK START.  
CAUTION: Keep in mind that the Heart Rate”  
or Training” zones are approximations.  
Always check with your physician to learn what  
the appropriate heart rate is for your level of  
fitness. Do not push yourself beyond the  
recommended range.  
Before using the Heart Rate capabilities on the M9.21i or M9.21si, take time to read the following  
guidelines.  
Consult with your physician before engaging in any vigorous exercise. Do not use the Heart  
Rate Course until authorized by your physician.  
Slow down and stop immediately if you experience any pain or abnormal symptoms.  
Gently stretch you lower body and back before and after working out to help prevent stiffness  
or soreness.  
Know your heart rate (pulse) and your physician-recommended heart rate training zone.  
Individual heart rates vary according to several physiological factors and may not correspond  
directly with the tables provided.  
You should not use the Heart Rate capabilities if you are taking any medications that either  
speed up or slow down your heart rate.  
CAUTION: Refer to Precor Heart Rate Option—  
Safety Guidelines for other important safety tips.  
Always face forward on your treadmill and only use the handrails for balance. Do not use the  
handrails to support your weight.  
Keep in mind that you are working with very sensitive equipment and upper body movement  
should be kept to a minimum.  
After putting on the chest strap, turn the treadmill ON O” and position yourself on the  
running belt for a minimum of 15 seconds. This allows the treadmill to acknowledge the  
presence of the transmitter.  
While using the chest strap, face the electronic console and stay within 3 feet of it. If you  
move outside the 3-foot range, the receiver may have difficulty picking up your heart rate  
signal.  
Remember to incorporate a cool-down period into your workout to help lower your heart rate  
and minimize muscle stiffness or soreness.  
Using the Heart Rate Course  
The Heart Rate Course has been designed from research conducted at the world-renowned Cooper  
Institute for Aerobics Research. The HRC program must be used in conjunction with the Precor  
Heart Rate Option. You can use the Heart Rate Course to maximize your aerobic workout. Once you  
start the program, the software automatically adjusts the incline (or prompts you to adjust the  
speed, if necessary) to keep your heart rate within the cardiovascular heart rate zone.  
Note: You must wear the Precor chest strap to use the Heart Rate Course.  
To use the course follow the steps in Working Out on the M9.21i or M9.21si Low Impact Treadmill  
and choose HRCat the SELECT COURSE” prompt. The following occurs:  
CAUTION: Always check with your physician to  
learn what the appropriate heart rate is for your  
level of fitness. Do not push yourself beyond  
the recommended range.  
1. A prompt asks you to select a workout time. The software defaults to 20 minutes if no  
previous record exists. You can select a range of time between 5 and 99 minutes in 1-minute  
increments. Use theor keys to specify your workout time. Press ENTER.  
2. A scrolling prompt appears to query you about your recommended heart rate zones. The upper  
limit of your target heart rate appears and scrolls across the display. Use theor keys if you  
wish to override the recommended heart rate. Press ENTER. A chart showing the recommended  
heart rate zones can be found in Diagram 15 in Getting the Most Out of Your Workout.  
3. Another scrolling prompt appears to ask you to verify your lower heart rate limit. Use the▼  
or keys if you wish to override the recommended heart rate. Press ENTER.  
page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The software verifies that it detects the heart rate signal and a prompt appears requesting that  
you press the SPEED key to begin your workout.  
Important: Hold onto the handrail. If the treadmill is not already at 0% incline, it automati-  
cally returns to 0% incline.  
5. Use the SPEEDor keys to control the running belt’s speed. The treadmill automatically  
adjusts the incline to keep your heart rate within the target zone. You can use the INCLINE or  
SPEED or keys any time during the 3-minute warm-up period to get your heart rate  
into its target zone. The program automatically takes over once your heart rate is in the  
target zone or the 3 minutes elapse. If, during your workout, your heart rate falls outside of  
the target range, the treadmill automatically overrides the incline (in 2% increments up to  
10%) to bring your heart rate to within the target zone.  
Note: If your heart rate cannot be detected or no heart rate is transmitted for more than 3  
minutes, the Heart Rate course begins, but its operation is the same as Manual mode. Every  
30 seconds the program checks for a heart rate.  
6. When you reach the time limit, the treadmill automatically enters Manual mode so you can  
begin a cool-down period. You can change the speed and incline by pressing the or ▲  
keys.  
During your cool down, the displays on the console continue to appear. The TIME display  
counts up from zero, so you know how long you have been in the cool-down period. It is  
recommended that you cool down for at least 3 minutes. This helps your heart rate to return  
to a normal rhythm.  
7. Hold onto the handrail and press the STOP key or press the SPEED key until the running  
belt slows to a gradual stop. The displays on the console freeze which lets you review your  
workout statistics. Straddle the running belt and remove the safety clip from your clothing.  
Step off the treadmill if you have finished your workout and turn it OFF.  
8. To prevent unauthorized use, remove the magnetic safety key from inside the electronic  
console and store it in a safe place.  
Correcting Inconsistent Heart Rate Readings  
If you have purchased the Precor Heart Rate Option and the treadmill cannot pick up your heart  
rate signal or messages appear on the display regarding heart rate errors, stop your workout and  
take the following steps:  
Important: Be sure that the optional heart rate receiver is installed in the electronic console. Also,  
review the information found in the Safety Information, Precor Heart Rate Option—Safety  
Guidelines.  
1. Make sure that the electrodes on the chest strap are moist and placed properly against your  
skin. Sometimes, due to body chemistry, the chest strap cannot successfully detect and  
transmit your heart rate. If this occurs, use the electrolyte spray that accompanies your Precor  
Heart Rate Option package. Follow the directions on the bottle. After spraying the electrode  
strips on the chest strap, check to be sure that the strap is comfortably tight around your  
chest. The brand name of the strap should be upright and centered in the middle of your  
chest. Refer to Diagram 13 in the section titled, Wearing the Chest Strap Transmitter.  
2. Make sure that the treadmill is turned ON and the magnetic safety key is secure.  
3. Be sure that you are within 3 feet of the electronic console and facing toward it. Allow a few  
seconds for the receiver to display your heart rate on the electronic console’s display.  
If you have taken the steps above and still get erratic readings, you may need to replace the chest  
strap transmitter or its battery. For chest straps with batteries, refer to Changing the Battery in the  
Chest Strap.  
Most often, when the chest strap fails to transmit a heart rate signal, the cause is incorrect  
placement or problems with the electrodes. Check with your local servicer, he or she has a chest  
strap/heart rate simulator that can test your equipment to make sure that it is operating properly.  
page 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting the Most Out of Your Workout  
6
To help you get started in planning and carrying out your fitness program, this section provides  
some basic information on aerobic exercise—such as how hard you should work out, how long  
each session should be, and how often you need to exercise to benefit from a regular program.  
Diagram 14  
Muscles improved  
1.  
Trapezius  
2.  
Deltoid  
1
1
3.  
Pectorals  
2
4.  
Rhomboids  
3
4
5.  
Triceps  
5
7
10  
6
6.  
Biceps  
9
7.  
Latissimus Dorsi  
Forearm Flexors/Extensors  
Abdominals  
8
8.  
8
9.  
11  
12  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
Erector Spinae  
Gluteals  
13  
Hip Flexors  
14  
Quadriceps  
Hamstrings  
Gastrocnemius/Soleus  
Peroneus Longus/Brevis  
15  
16  
16  
A workout on the M9.21i or M9.21si Low Impact Treadmill provides excellent and efficient  
cardiovascular conditioning, while strengthening and toning all the major muscle groups in the  
lower body. Darkened areas in Diagram 14 indicate the muscles improved.  
To get the most out of each workout, a general understanding of the principles behind aerobic  
training is invaluable. The best source of information is your specialty fitness dealer. In addition to  
providing information on which exercise equipment is best for your individual needs, your fitness  
dealer can provide useful advice on training, technique, and exercise physiology. Your dealer can  
also recommend good books and audio/video tapes on these subjects.  
How Hard Should I Exercise?  
Studies show that to achieve the benefits of aerobic exercise, it is necessary to work out hard  
enough to raise your heart rate to a certain minimum level, called the training zone.” Your training  
zone depends on your age and level of fitness.  
page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Diagram 15  
Training zones  
HEART RATE TRAINING ZONE  
200  
195  
190  
185  
180  
175  
170  
165  
200  
190  
180  
170  
160  
160  
160  
156  
155  
152  
124  
150  
148  
144  
145  
150  
140  
140  
136  
MAX.  
132  
RECOMMENDED TRAINING ZON1E28  
HEART  
RATE  
124  
101  
130  
120  
100  
90  
120  
97  
130  
116  
94  
127  
120  
117  
114  
111  
107  
104  
80% OF  
MAX.  
HEART  
RATE  
65% OF  
MAX.  
HEART  
RATE  
80  
70  
20  
25 30 35 40 45 50 55 60 65 70 75  
YOUR AGE  
Diagram 15 shows your recommended heart rate training zone, which is calculated using your age  
and your maximum aerobic heart rate. Your maximum aerobic heart rate is equal to 220 minus  
your age. The chart is based on a resting heart rate of about 72 for males and 80 for females. Your  
optimum training zone is between 65% and 80% of your maximum heart rate. For efficient aerobic  
exercise, work only hard enough to keep your heart rate in this zone. You will obtain the greatest  
fat-burning benefits when you exercise within the optimum training zone.  
Pushing yourself beyond the recommended range, (that is, exercising so hard that your heart rate  
rises above 80% of maximum) can overstress your muscles. To increase cardiovascular improve-  
ment, exercise longer, not harder.  
Keep in mind that this zone is an approximation, to be used as a guideline—individual heart rates  
vary according to several physiological factors. To determine your training zone, find your age on  
the diagram, and then find the line where they intersect. For example, if you are 35 years old, your  
training zone is between 114 and 140 beats per minute. Remember this zone—this is the heart rate  
zone you should try to maintain as you work out.  
If you do not have an accurate heart rate monitor, you can determine your heart rate by taking your  
pulse at a place that you can reach easily and comfortably while you exercise. Typical places for  
measuring heart rate are directly over the heart on the left side of the chest, on either side of the  
neck, over the temple, or on the thumb side of either wrist. Wherever you measure your pulse,  
make sure that you use your index and middle fingers—not your thumb. Your thumb has a strong  
pulse which can affect your pulse rate reading.  
Once you locate your pulse, look at a clock with a second hand, and count the beats for six  
seconds. Multiply that number by 10 to determine the total number of beats per minute. For  
example, if you count 14 beats over six seconds, the total number of beats per minute is 140.  
Compare the total number of beats with your training zone as identified in Diagram 15. If neces-  
sary, increase or decrease your activity level to bring your heart rate into your training zone. You  
can regulate your work level (and heart rate) by changing belt speed and incline. Remember—your  
heart rate is the definitive measure of how hard you are working.  
Regardless of your fitness level, avoid doing too much too soon. Running or walking too fast or  
choosing too high of an incline are common errors. Give yourself time to become familiar with  
your treadmill and to improve your fitness level. Then you can gradually increase speed and incline  
to make your workouts more challenging.  
page 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How Long Should I Exercise?  
The length of each exercise session depends on your fitness level. Exercise physiologists have  
determined that, to attain cardiovascular benefits from exercise, you should maintain your heart  
rate in its training zone for at least 15 minutes. This is in addition to your warm-up time, and does  
not include cool down. You should always allow several minutes to bring your heart rate into the  
training zone, by starting out slowly and gradually increasing work level. Similarly, use several  
minutes of light exercise after the workout to bring your heart rate down to near resting level.  
The higher your fitness level, the longer you should maintain your heart rate in the training zone  
(between 20 and 30 minutes). Beginners should always start slowly, and gradually bring their  
sessions up to 20 minutes or more.  
How Often Should I Exercise?  
Research indicates that aerobic sessions of 20 minutes or more should be done at least three to  
five times a week to obtain significant cardiovascular benefits. Most experts agree that sensible  
eating habits and regular aerobic exercise are the keys to weight control and fitness. A recent  
study, which tracked several subjects over a period of years, conclusively shows that exercise, not  
dieting, is the key factor to long-term weight loss.  
page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintaining the Low Impact Treadmills  
7
The M9.21i or M9.21si Low Impact Treadmill requires little maintenance to keep it running  
smoothly and efficiently. However, the customer is responsible for the typical maintenance tasks  
such as, cleaning the treadmill and adjusting the running belt. If you fail to maintain the treadmill  
as described below, it could affect or void the limited warranty.  
Cleaning the Equipment  
CAUTION: Turn OFF the treadmill and discon-  
nect the power cord before performing most  
maintenance tasks.  
Your Precor treadmill relies on low friction for efficient operation. To keep the friction low, the  
treadmill must be as clean as possible.  
Before a workout, use a damp, soft, clean cloth to clean the side platforms and running bed, (refer  
to Diagram 17 on page 33). This helps to remove any dirt or dust that might affect the smooth  
operation of the treadmill.  
Vacuum the floor underneath the unit every week to prevent the accumulation of dust and dirt on  
the running belt.  
CAUTION: Do not use an abrasive cleaner on  
the strap. Do not immerse any part of the chest  
strap. Do not spray or pour liquids on any part  
of the equipment.  
To periodically clean the treadmill’s frame, electronic console, and running belt, use a solution of  
mild soap and water and dampen a clean cloth. To clean the running belt and the groves on the  
plastic trim strip, use a soft nylon scrub brush. Never pour water or spray liquids on the electronic  
console. Allow the treadmill to dry completely before using it.  
Manually advance the running belt to clean the opposite side. Do not clean the belt while the  
running belt is moving. Liquid can splash onto the motor causing damage to the equipment and  
possibly injuring you.  
The Precor Heart Rate Option equipment requires little maintenance beyond keeping it dust free  
and cleaning the chest strap with mild soap and water. Use a damp sponge or soft cloth to clean  
the chest strap. Dry the surface thoroughly with a clean towel.  
Changing the Battery in the Chest Strap  
Some Precor Heart Rate Option’s chest straps come equipped with a battery. Others are the  
disposable variety. If you have a battery-type chest strap, the signs that the battery is low and  
needs to be replaced include:  
erratic heart rate display  
no heart rate display appears  
To replace the battery, take the following steps:  
1. Use a quarter or flathead screwdriver to open the battery case located between the two  
electrode strips on the chest strap. See Diagram 16. Set the battery cover aside.  
Changing the battery  
Diagram 16  
Battery case  
page 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Remove the old battery and replace it with a fresh one. Make sure that the positive (+) side  
is up facing you.  
3. Screw the battery cover back into place.  
4. Test the battery by putting on the chest strap as described in Wearing the Chest Strap  
Transmitter. Stand within 3 feet and face the electronic console. (Be sure that the treadmill is  
turned ON). If the battery has been installed properly, your heart rate should appear on the  
display when you begin a workout program.  
Storing the Chest Strap  
Store the chest strap transmitter in a place where dust and dirt cannot accumulate on it such as, a  
closet or drawer. Be sure to keep the chest strap protected from extremes in temperature. Do not  
store it in an area that may be exposed to temperatures below 32 degrees Fahrenheit.  
Aligning the Running Belt  
CAUTION: Special care must be taken when  
aligning the running belt. Turn OFF the treadmill  
while adjusting or working near the rear roller.  
Remove any loose clothing and tie back your  
hair. Be very careful to keep your fingers or any  
other object clear of the belt and rollers,  
Before aligning the running belt, check its operation by following the procedure in Checking the  
Alignment of the Running Belt on page 14. If you determine that the belt needs alignment, follow  
the instructions here.  
Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, call  
your authorized Precor dealer for service (see Obtaining Service).  
especially in front of the roller and behind the  
deck. The treadmill will not stop immediately if  
an object becomes caught in the belt or rollers.  
Take the following steps to adjust the running belt on the treadmill. To ensure your safety, make all  
adjustments while the treadmill is OFF.  
Diagram 17  
Alignment of the  
running belt  
Running bed  
Side platform  
CAUTION: Turn OFF the treadmill and wit for the belt to stop  
when adjusting or working near the rear roller. Be very careful  
to keep your fingers or any loose object clear of the belt and  
rollers. The treadmill wll not stop immeadiately if an object  
becomes caught in the belt or rollers.  
Rear roller  
Belt adjustment bolt  
Running belt  
1. Make sure the treadmill is OFF and the running belt has completely stopped.  
2. Locate the left belt adjustment bolt at the rear of the treadmill as shown in Diagram 17. The  
direction you turn the bolt depends on how the belt is tracking. Make all belt adjustments on  
the left rear corner bolt using the hex key provided.  
If the belt is off center to the LEFT, turn the adjusting bolt 1/4 turn clockwise, which  
moves the running belt to the right.  
If the belt tracks off center to the RIGHT, turn the bolt 1/4 turn counterclockwise; this  
moves the belt to the left.  
Important: Do not turn the adjusting bolt more than 1/4 turn at a time. Overtightening the bolt  
can damage the treadmill.  
page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION: Stand to the side of the treadmill.  
The running belt begins moving automatically  
after you press QUICK START.  
3. Insert the Safety key, turn ON the treadmill, press the QUICK START key, and then increase  
the running belt speed to 3 mph (5 kph) by pressing the SPEED key.  
4. Observe the running belt for a couple of minutes. The belt should track centered on the  
running bed.  
CAUTION: If you hear a chafing sound or the  
belt begins to tear or fray, stop the running belt  
immediately by pressing the STOP key or  
pulling the magnetic safety key out of the  
electronic console. Contact your Precor service  
representative.  
5. Press STOP to stop the running belt.  
6. If the belt needs additional alignment, repeat steps 1 through 5 of this procedure until the belt  
is properly aligned.  
Adjusting the Tension of the Belt  
Proper belt tension is important for a smooth, steady run. If your physical condition permits, test  
the belt tension by jogging at 6 mph (10 kph). If the belt tension is too loose, you will feel a pause  
in the belt with each footplant (step).  
To adjust the running belt tension, take the following steps:  
1. Make sure that the treadmill is OFF (O). If the treadmill is ON ( I ), switch it to OFF. Wait for  
the running belt to come to a complete stop.  
Diagram 18  
Adjusting tension of the belt  
Running bed  
Side platform  
Rear roller  
Belt adjustment bolt  
Running belt  
2. Standing behind the treadmill use the rear belt adjustment bolts (see Diagram 17 on the  
previous page and Diagram 18). Simply turn each bolt clockwise 1/4 turn to adjust the tension  
of the belt.  
CAUTION: Stand to the side of the treadmill.  
The running belt begins moving automatically  
after you press QUICK START.  
3. Insert the Safety key, turn ON the treadmill, answer the start-up prompts, then increase the  
speed of the running belt to 6 miles per hour (10 kph) by pressing the SPEED key.  
4. Jog on the running belt for 1 minute or more. If you feel a pause in the belt with each  
footplant (step), you need to continue to adjust the belt tension.  
5. Press STOP to stop the running belt.  
6. Continue with steps 1 through 5 until the belt tension has been properly adjusted and you no  
longer feel the pause in the belt with each footplant.  
Important: Do not turn the adjusting bolts more than 1/4 turn at a time. Overtightening the  
bolts can damage or cause premature failure of the precision bearings in the front and rear  
rollers.  
page 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Obtaining Service  
Do not attempt to service the M9.21i or M9.21si Low Impact Treadmill yourself except for minor  
belt adjustments and maintenance as described in this manual. The M9.21i or M9.21si treadmill  
does not contain any user-serviceable parts.  
For information about product operation or service, contact an authorized Precor dealer or a Precor  
Factory Authorized Service Company. To locate the dealer or service person nearest you, call 1-  
800-4-PRECOR.  
To help the customer service representative expedite your call, have your serial number available.  
The serial number on the treadmill is printed on a label located underneath the treadmill at the left,  
rear corner of the running bed frame. If you haven't already written the serial number in the space  
provided below during the assembly process, you will need to get on your knees and bend down to  
see it.  
Model number: _M_9_._2_1_i_o_r_M_9_._2_1_s_i_ Serial number: _________________________  
If you have any questions regarding the treadmill, use the model and serial numbers whenever you  
call your Precor dealer or service person.  
page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M9.21i and M9.21si Low Impact Treadmills  
featuring the Heart Rate Interactive System  
Specifications  
Length:  
Width:  
67 inches (170 cm)  
Handrails 28.5 inches (71 cm)  
Base 25 inches (63.5 cm)  
44 inches  
Height:  
Runningsurface:  
Motor:  
51 inches by 17 inches (129.5 cm by 43 cm)  
2.0 hp continuous duty  
Speed:  
0.5 to 10 mph (0.8 to 16 kph)  
10 mph is equivalent to a 6 minute mile  
0 to 15% grade  
Incline:  
Power:  
Weight:  
50/60Hz 120v AC 12 Amps  
193 lbs (87 kg)  
Shippingweight:  
233 lbs (105 kg)  
Electronic Specifications  
M9.21i Programs:  
M9.21i and M9.21si Display Readouts:  
Manual  
Distance (miles or kilometers)  
Time  
Interval (1 minute rest: 1 minute work)  
Weight Loss  
Random  
Speed (mph or kph)  
Calories  
Heart Rate Interactive Course*  
Incline  
Heart rate* and Smart Rate®*  
Scan  
M9.21si Programs:  
Manual  
Interval (1 minute rest: 1 minute work)  
Weight Loss  
6 Preprogrammed courses (3 Walk, 3 Run)  
2 Custom courses  
Random  
Heart Rate Interactive Course*  
*Requires the Precor Heart Rate Option kit.  
R
Precor Incorporated  
P.O. Box 3004  
Bothell, WA USA 98041-3004  
Precor, M, and Smart Rate are registered trademarks and Cardiologic and  
CrossRamp, and Quick Start are trademarks of Precor Incorporated.  
© 2000 Precor Incorporated.  
P/N 37975-101  
9/97  
Specifications subject to change without notice.  
1-800-4-PRECOR  
NOTICE:  
Precoriswidelyrecognizedforitsinnovative, awardwinningdesignsofexerciseequipment.  
PrecoraggressivelyseeksU.S.andforeignpatentsforboththemechanicalconstructionand  
thevisualaspectsofitsproductdesign. AnypartycontemplatingtheuseofPrecor’sproduct  
designs is hereby forewarned that Precor considers the unauthorized appropriation of its  
proprietary rights to be a very serious matter. Precor will vigorously pursue all unauthorized  
appropriation of its proprietary rights.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Musical Instrument Amplifier 210TX User Manual
Philips Blender RI1764 User Manual
Philips Blu ray Player DMP BD30 User Manual
Philips Computer Monitor 107F User Manual
Philips MP3 Player 1037 User Manual
Philips Refrigerator AC4052 User Manual
Philips Surge Protector SPP1188WA User Manual
Philips TV Antenna SDV1121 User Manual
Polycom IP Phone IP3000 3COM User Manual
Precor Exercise Bike 537 User Manual