ADSL 2/2+
VPN Firewall Router
ADW-4302A v2 / ADW-4302B v2
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio
equipment and telecommunication terminal Equipment and the mutual recognition
of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecom-
munications Terminal Equipment and Satellite Earth Station Equipment) As of April
8,2000.
WEEE
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted mu-
nicipal waste and have to collect such WEEE separately.
Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines of this
and of the computer manufacture must therefore be allowed at all times to ensure
the safe use of the equipment.
Revision
User’s Manual for 802.11g Wireless PLANET ADSL 2/2+ VPN Firewall Router
Model: ADW-4302A v2 / ADW-4302B v2
Rev: 1.0 (Jul. 2006)
Part No. EM-ADW4302v2_v1
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
CHAPTER 2 INSTALLATION....................................................................................... 6
Procedure.............................................................................................................. 6
Overview................................................................................................................ 8
Setup Wizard....................................................................................................... 11
Trusted Wireless Stations ................................................................................ 21
Overview.............................................................................................................. 25
Macintosh Clients............................................................................................... 36
Overview.............................................................................................................. 55
VPN (IPSec) ........................................................................................................ 75
Microsoft VPN .................................................................................................... 84
Overview.............................................................................................................. 98
E-mail................................................................................................................. 106
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Administration.................................................................................... 109
Upgrade Firmware............................................................................................ 115
Overview............................................................................................................ 116
APPENDIX A TROUBLESHOOTING....................................................................... 121
Overview............................................................................................................ 121
General Problems............................................................................................. 121
Internet Access................................................................................................. 121
Wireless Access .............................................................................................. 122
Overview............................................................................................................ 127
ADSL 2/2+ VPN Firewall Router...................................................................... 134
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
1
Introduction
This Chapter provides an overview of the ADW-4302v2's features and
capabilities.
Congratulations on the purchase of your new ADW-4302v2. The ADW-4302v2 is a
multi-function device providing the following services:
•
•
•
•
•
ADSL 2/2+ Modem.
Shared Broadband Internet Access for all LAN users.
Wireless Access Point for 802.11b and 802.11g Wireless Stations.
VPN Gateway to allow secure VPN connections over the Internet.
4-Port Switching Hub for 10BaseT or 100BaseT connections.
Figure 1: ADW-4302v2
ADW-4302v2 Features
The ADW-4302v2 incorporates many advanced features, carefully designed to pro-
vide sophisticated functions while being easy to use.
Internet Access Features
•
Shared Internet Access. All users on the LAN or WLAN can access the Internet
through the ADW-4302v2, using only a single external IP Address. The local (in-
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
valid) IP Addresses are hidden from external sources. This process is called NAT
(Network Address Translation).
•
•
•
Built-in ADSL 2/2+ Modem. The ADW-4302v2 has a built-in ADSL 2/2+ modem,
supporting all common ADSL 2/2+ connections.
IPoA, PPPoE, PPPoA, Direct Connection Support. The ADW-4302v2 supports
all common connection methods.
Auto-detection of Internet Connection Method. In most situations, the ADW-
4302v2 can test your ADSL and Internet connection to determine the connection
method used by your ISP.
•
Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the
ADW-4302v2 supports both Dynamic IP Address (IP Address is allocated on con-
nection) and Fixed IP Address.
Advanced Internet Functions
•
Application Level Gateways (ALGs). Applications which use non-standard
connections or port numbers are normally blocked by the Firewall. The ability to
define and allow such applications is provided, to enable such applications to be
used normally.
•
•
•
•
•
•
•
Special Applications. This feature, also called Port Triggering, allows you to use
Internet applications which normally do not function when used behind a firewall.
Virtual Servers. This feature allows Internet users to access Internet servers on
your LAN. The required setup is quick and easy.
URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN
users.
Logs. Define what data is recorded in the Logs, and optionally send log data to a
Syslog Server. Log data can also be E-mailed to you.
Access Control. Allows administrators to restrict the Internet Access available to
PCs on your LAN.
Firewall. As well as the built-in firewall to protect your LAN, you can define Fire-
wall Rules to determine which incoming and outgoing traffic should be permitted.
Universal Plug and Play (UPnP). UPnP allows automatic discovery and con-
figuration of the Broadband Router. UPnP is supported by Windows ME, XP, or
later.
•
•
Dynamic DNS Support. DDNS, when used with the Virtual Servers feature,
allows users to connect to Servers on your LAN using a Domain Name, even if
you have a dynamic IP address which changes every time you connect.
Scheduling. Both the URL Filter and Firewall rules can be scheduled to operate
only at certain times. This provides great flexibility in controlling Internet -bound
traffic.
•
•
•
VPN Connectivity. Supports up to 8 IPSec VPN with DES, 3DES encryption and
SHA-1 / MD5 authentication, the network traffic over public Internet is secured.
PPTP Server. The ADW-4302v2 emulates a Microsoft PPTP VPN Server, allow-
ing clients to use the Microsoft VPN client provided in Windows.
VPN Pass through Support. PCs with VPN (Virtual Private Networking) soft-
ware using PPTP, L2TP and IPSec are transparently supported - no configuration
is required.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Wireless Features
•
Standards Compliant. The ADW-4302v2 complies with the IEEE802.11g (DSSS)
specifications for Wireless LANs.
•
Supports both 802.11b and 802.11g Wireless Stations. The 802.11g standard
provides for backward compatibility with the 802.11b standard, so both 802.11b
and 802.11g Wireless stations can be used simultaneously.
•
•
Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are
supported.
WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key
sizes of 64 Bit and 128 Bit are supported. WEP encrypts any data before trans-
mission, providing protection against snoopers.
•
•
•
WPA-PSK support. Like WEP, WPA-PSK encrypts any data before transmission,
providing protection against snoopers. The WPA-PSK is a later standard than
WEP, and provides both easier configuration and greater security than WEP.
Wireless MAC Access Control. The Wireless Access Control feature can check
the MAC address (hardware address) of Wireless stations to ensure that only
trusted Wireless Stations can access your LAN.
Simple Configuration. If the default settings are unsuitable, they can be
changed quickly and easily.
LAN Features
•
4-Port Switching Hub. The ADW-4302v2 incorporates a 4-port 10/100BaseT
switching hub, making it easy to create or extend your LAN.
•
DHCP Server Support. Dynamic Host Configuration Protocol provides a dy-
namic IP address to PCs and other devices upon request. The ADW-4302v2 can
act as a DHCP Server for devices on your local LAN and WLAN.
Configuration & Management
•
Easy Setup. Use your WEB browser from anywhere on the LAN or WLAN for
configuration.
•
Configuration File Upload/Download. Save (download) the configuration data
from the ADW-4302v2 to your PC and restore (upload) a previously-saved con-
figuration file to the ADW-4302v2.
•
•
Remote Management. The ADW-4302v2 can be managed from any PC on your
LAN or Wireless LAN. And, if the Internet connection exists, it can also (optionally)
be configured via the Internet.
Network Diagnostics. You can use the ADW-4302v2 to perform a Ping or DNS
lookup.
Security Features
•
Password - protected Configuration. Password protection is provided to pre-
vent unauthorized users from modifying the configuration data and settings.
•
Wireless LAN Security. WPA-PSK, WEP and Wireless access control by MAC
address are all supported. The MAC-level access control feature can be used to
prevent unknown wireless stations from accessing your LAN.
•
NAT Protection. An intrinsic side effect of NAT (Network Address Translation)
technology is that by allowing all LAN users to share a single IP address, the loca-
tion and even the existence of each PC is hidden. From the external viewpoint,
there is no network, only a single device - the ADW-4302v2.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
•
•
Firewall. All incoming data packets are monitored and all incoming server re-
quests are filtered, thus protecting your network from malicious attacks from
external sources.
Protection against DoS attacks. DoS (Denial of Service) attacks can flood your
Internet connection with invalid packets and connection requests, using so much
bandwidth and so many resources that Internet access becomes unavailable. The
ADW-4302v2 incorporates protection against DoS attacks.
Package Contents
The following items should be included. If any of these items are damaged or missing,
please contact your dealer immediately.
•
•
•
•
•
•
The ADW-4302v2 Unit
Quick Installation Guide
User’s Manual CD
Power Adapter
1 RJ-45 Cable
1 RJ-11 (ADSL) cable
Physical Details
Front-mounted LEDs of ADW-4302v2
Figure 2: Front Panel of ADW-4302v2
POWER
STATUS
On - Power on.
Off - No power.
Off - Normal operation.
Blinking - This LED blinks during start up, and during a Firmware
Upgrade.
For each port, there are 2 LEDs, to indicate the connection speed
(10BaseT or 100BaseT) of each port.
LAN
•
•
•
100 LNK/ACT - This will be ON if the LAN connection is using
100BaseT, and Blinking if data is being transferred via the cor-
responding LAN port.
10 LNK/ACT - This will be ON if the LAN connection is using
10BaseT, and Blinking if data is being transferred via the corre-
sponding LAN port.
If neither LED is on, there is no active connection on the corre-
sponding LAN port.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
WLAN
On - Wireless enabled.
Off - No Wireless connections currently exist.
Flashing - Data is being transmitted or received via the Wireless
access point. This includes "network traffic" as well as user data.
ADSL
On - ADSL connection is available.
Off - No ADSL connection available.
Flashing - Data is being transmitted or received via the ADSL
connection.
Internet
On - Internet connection is available.
Off - No Internet connection available.
Flashing - Data is being transmitted or received.
Rear Panel
Figure 3: Rear Panel of ADW-4302v2
This button will reset the ADW-4302v2 to the factory default
settings.
To do this, press and hold the Reset Button for five (5) sec-
onds, until the Status LED is lit, then release the Reset Button,
and wait the ADW-4302v2 to restart using the factory default
values.
RESET Button
(Reset to De-
faults)
Connect the supplied power adapter here.
POWER port
Use standard LAN cables (RJ45 connectors) to connect your
PCs to these ports.
10/100BaseT
LAN connec-
tions
Note:
Any LAN port on the ADW-4302v2 will automatically function
as an "Uplink" port when required. Just connect any port to a
normal port on the other hub, using a standard LAN cable.
Connect this port to your ADSL line.
ADSL port
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
2
Installation
This Chapter covers the physical installation of the ADW-4302v2.
Requirements
•
Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45
connectors.
•
•
TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and a DSL connec-
tion.
•
To use the Wireless Access Point, all Wireless devices must be compliant with the
IEEE 802.11g or IEEE 802.11b specifications.
Procedure
ADSL line
To PC/Hub
To Power Adapter
Figure 4: Installation Diagram
1. Choose an Installation Site
Select a suitable place on the network to install the ADW-4302v2.
For best Wireless reception and performance, the ADW-
4302v2 should be positioned in a central location with mini-
mum obstructions between the ADW-4302v2 and the PCs.
Also, if using multiple Access Points, adjacent Access
Points should use different Channels.
2. Connect LAN Cables
Use standard LAN cables to connect PCs to the Switching Hub ports on the ADW-
4302v2. Both 10BaseT and 100BaseT connections can be used simultaneously.
If required, connect any port to a normal port on another Hub, using a standard
LAN cable. Any LAN port on the ADW-4302v2 will automatically function as an
"Uplink" port when required.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Connect ADSL Cable
Connect the supplied ADSL cable from to the WAN port on the ADW-4302v2 (the
RJ-11 connector) to the ADSL terminator provided by your phone company.
4. Power Up
Connect the supplied power adapter to the ADW-4302v2. Use only the power
adapter provided. Using a different one may cause hardware damage.
5. Check the LEDs
•
•
The Power LED should be ON.
The Status LED should flash, then turn Off. If it stays on or blinking after 60 sec-
onds, there is a hardware error.
•
For each LAN (PC) connection, one of the LAN LEDs should be ON (provided the
PC is also ON.)
•
•
•
The WLAN LED should be ON.
The WAN LED should be ON if ADSL line is connected.
The Internet LED may be OFF. After configuration, it should come ON.
For more information, refer to Front-mounted LEDs in Chapter 1.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
3
Setup
This Chapter provides Setup details of the ADW-4302v2.
Overview
This chapter describes the setup procedure for:
•
•
•
•
Internet Access
LAN configuration
Wireless setup
Assigning a Password to protect the configuration data.
PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC
Configuration.
Other configuration may also be required, depending on which features and functions
of the ADW-4302v2 you wish to use. Use the table below to locate detailed instruc-
tions for the required functions.
To Do this:
Refer to:
Configure PCs on your LAN.
Chapter 4:
PC Configuration
Check ADW-4302v2 operation and Status.
Chapter 5:
Operation and Status
Use any of the following Advanced features:
Chapter 6:
Advanced Features
•
•
•
•
•
•
•
Internet (DMZ, Special Applications, URL Filter)
Dynamic DNS
Firewall Rules
Firewall Services
Schedule
Virtual Servers
VPN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Use any of the following Administration Configuration Chapter 7
settings or features: Advanced Administration
•
•
•
•
•
•
•
•
PC Database
Config File
Logging
E-mail
Diagnostics
Remote Admin
Routing
Upgrade Firmware
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Configuration Program
The ADW-4302v2 contains an HTTP server. This enables you to connect to it, and
configure it, using your Web Browser. Your Browser must support JavaScript.
The configuration program has been tested on the following browsers:
•
•
•
Netscape V4.08 or later
Netscape 7
Internet Explorer V5.01 or later
Preparation
Before attempting to configure the ADW-4302v2, please ensure that:
•
Your PC can establish a physical connection to the ADW-4302v2. The PC and the
ADW-4302v2 must be directly connected (using the Hub ports on the ADW-
4302v2) or on the same LAN segment.
•
•
The ADW-4302v2 must be installed and powered ON.
If the ADW-4302v2's default IP Address (192.168.0.1) is already used by another
device, the other device must be turned OFF until the ADW-4302v2 is allocated a
new IP Address during configuration.
Using your Web Browser
To establish a connection from your PC to the ADW-4302v2:
1. After installing the ADW-4302v2 in your LAN, start your PC. If your PC is already
running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the ADW-4302v2, as in
this example, which uses the ADW-4302v2's default IP Address:
HTTP://192.168.0.1
4. When prompted for the User name and Password, enter default user name admin
and password admin.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
If you can't connect
If the ADW-4302v2 does not respond, check the following:
•
The ADW-4302v2 is properly installed, LAN connection is OK, and it is
powered ON. You can test the connection by using the "Ping" com-
mand:
•
•
Open the MS-DOS window or command prompt window.
Enter the command:
ping 192.168.0.1
If no response is received, either the connection is not working, or your
PC's IP address is not compatible with the ADW-4302v2's IP Address.
(See next item.)
•
If your PC is using a fixed IP Address, its IP Address must be within the
range 192.168.0.2 to 192.168.0.254 to be compatible with the ADW-
4302v2's default IP Address of 192.168.0.1. Also, the Network Mask
must be set to 255.255.255.0. See Chapter 4 - PC Configuration for de-
tails on checking your PC's TCP/IP settings.
•
•
Ensure that your PC and the ADW-4302v2 are on the same network
segment. (If you don't have a router, this must be the case.)
Ensure you are using the wired LAN interface. The Wireless interface
can only be used if its configuration matches your PC's wireless set-
tings.
Setup Wizard
When you connect to the ADW-4302v2, you may use the Setup Wizard function to
setup the configurations of ADSL (The Setup Wizard will also run if the ADW-4302v2's
default settings are restored.)
1. Step through the Wizard until finished.
•
You need the data supplied by your ISP. Most connection methods require some
data input.
•
The common connection types are explained in the following table.
2. On the final screen of the Wizard, run the test and check that an Internet connec-
tion can be established.
3. If the connection test fails:
•
•
Check all connections, and the front panel LEDs.
Check that you have entered all data correctly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Common Connection Types
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allocated
automatically, when you con-
nect to you ISP.
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automati-
cally.
b) Some ISP's may require
you to use a particular Host-
name or Domain name, or
MAC (physical) address.
Static (Fixed)
IP Address
Your ISP allocates a perma-
nent IP Address to you.
Usually, the connection is
"Always on".
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automati-
cally.
b) IP Address allocated to you,
and related information, such
as Network Mask, Gateway IP
address, and DNS address.
PPPoE, PPPoA
You connect to the ISP only
a) ADSL parameters (VPI and
when required. The IP address VCI) may be required, if they
is usually allocated automati-
cally.
cannot be detected automati-
cally.
b) User name and password
are always required.
c) If using a Static (Fixed) IP
address, you need the IP
address and related informa-
tion (Network Mask, Gateway
IP address, and DNS address)
IPoA
(IP over ATM)
Normally, the connection is
"Always on".
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automati-
cally.
b) IP Address allocated to you,
and related information, such
as Network Mask, Gateway IP
address, and DNS address.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Home Screen
After finishing the Setup Wizard, you will see the Home screen. When you connect in
future, you will see this screen when you connect. An example screen is shown below.
Figure 5: Home Screen
Main Menu
The main menu, on the left, contains links to the most-commonly used screen. To see
the links to the other available screens, click "Advanced" or "Administration".
The main menu also contains two (2) buttons:
•
•
Log Out - When finished, you should click this button to logout.
Restart - Use this if you wish to restart the ADW-4302v2. Note that restarting the
Router will break any existing connections to or through the Router.
Navigation & Data Input
•
Use the menu bar on the left of the screen, and the "Back" button on your Browser,
for navigation.
•
Changing to another screen without clicking "Save" does NOT save any changes
you may have made. You must "Save" before changing screens or your data will
be ignored.
On each screen, clicking the "Help" button will
display help for that screen.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
LAN Screen
Use the LAN link on the main menu to reach the LAN screen. An example screen is
shown below.
Figure 6: LAN Screen
Data - LAN Screen
TCP/IP
IP address for the ADW-4302v2, as seen from the local LAN.
Use the default value unless the address is already in use or
your LAN is using a different IP address range. In the latter
case, enter an unused IP Address from within the range used by
your LAN.
IP Address
The default value 255.255.255.0 is standard for small (class "C")
networks. For other networks, use the Subnet Mask for the LAN
segment to which the ADW-4302v2 is attached (the same value
as the PCs on that LAN segment).
Subnet Mask
DHCP Server
•
If Enabled, the ADW-4302v2 will allocate IP Addresses to
PCs (DHCP clients) on your LAN when they start up. The
default (and recommended) value is Enabled.
•
If you are already using a DHCP Server, this setting must be
Disabled, and the existing DHCP server must be re-
configured to treat the ADW-4302v2 as the default Gateway.
See the following section for further details.
•
The Start IP Address and Finish IP Address fields set the
values used by the DHCP server when allocating IP Ad-
dresses to DHCP clients. This range also determines the
number of DHCP clients supported.
See the following section for further details on using DHCP.
DHCP
What is DHCP
A DHCP (Dynamic Host Configuration Protocol) Server allocates a valid IP address to
a DHCP Client (PC or device) upon request.
•
The client request is made when the client device starts up (boots).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
•
The DHCP Server provides the Gateway and DNS addresses to the client, as well
as allocating an IP Address.
•
•
The ADW-4302v2 can act as a DHCP server.
Windows 95/98/ME and other non-Server versions of Windows will act as a DHCP
client. This is the default Windows setting for the TCP/IP network protocol. How-
ever, Windows uses the term Obtain an IP Address automatically instead of
"DHCP Client".
•
You must NOT have two (2) or more DHCP Servers on the same LAN segment.
(If your LAN does not have other Routers, this means there must only be one (1)
DHCP Server on your LAN.)
Using the ADW-4302v2's DHCP Server
This is the default setting. The DHCP Server settings are on the LAN screen. On this
screen, you can:
•
•
Enable or Disable the ADW-4302v2's DHCP Server function.
Set the range of IP Addresses allocated to PCs by the DHCP Server function.
You can assign Fixed IP Addresses to some devices
while using DHCP, provided that the Fixed IP Addresses
are NOT within the range used by the DHCP Server.
Using another DHCP Server
You can only use one (1) DHCP Server per LAN segment. If you wish to use another
DHCP Server, rather than the ADW-4302v2's, the following procedure is required.
•
Disable the DHCP Server feature in the ADW-4302v2. This setting is on the LAN
screen.
•
Configure the DHCP Server to provide the ADW-4302v2's IP Address as the
Default Gateway.
To Configure your PCs to use DHCP
This is the default setting for TCP/IP for all non-Server versions of Windows.
See Chapter 4 - Client Configuration for the procedure to check these settings.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Wireless Screen
The ADW-4302v2's settings must match the other Wireless stations.
Note that the ADW-4302v2 will automatically accept both 802.11b and 802.11g con-
nections, and no configuration is required for this feature.
To change the ADW-4302v2's default settings for the Wireless Access Point feature,
use the Wireless link on the main menu to reach the Wireless screen. An example
screen is shown below.
Figure 7: Wireless Screen
Data - Wireless Screen
Identification
Select the correct domain for your location. It is your responsibil-
ity to ensure:
Region
•
That the ADW-4302v2 is only used in domains for which is
licensed.
•
That you select the correct domain, so that only the legal
channels for that domain can be selected.
This is the same as the "Device Name" for the ADW-4302v2.
Station name
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
This is also called the "Network Name".
SSID
•
If using an ESS (Extended Service Set, with multiple access
points) this ID is called an ESSID (Extended Service Set
Identifier).
•
To communicate, all Wireless stations should use the same
SSID/ESSID.
Options
Mode
Select the desired mode:
•
802.11G-plus (TI) This allows clients to use any of the
following modes:
•
•
•
•
Standard 802.11b
802.11B+ (Texas Instruments proprietary enhanced mode)
Standard 802.11g
802.11G-plus (Texas Instruments proprietary enhanced
mode). This mode can increase throughput by up to 50%,
but will only work between compatible TI wireless stations.
•
•
•
802.11g & 802.11b - Both 802.11.g and 802.11b Wireless
stations will be able to use the ADW-4302v2.
802.11g only - Only 802.11g Wireless stations can use the
ADW-4302v2.
802.11b only - Only 802.11b connections are available.
802.11g Wireless Stations will only be able to use the ADW-
4302v2 if they are fully backward-compatible with the
802.11b standard.
Select the Channel you wish to use on your Wireless LAN.
Channel No.
•
If you experience interference (shown by lost connections
and/or slow data transfers) you may need to experiment with
different channels to see which is the best.
•
If using multiple Access Points, adjacent Access Points
should use different Channels to reduce interference.
If enabled, the ADW-4302v2 will broadcast its SSID. This allows
PCs and other wireless stations to detect this Access Point and
use the correct SSID.
Broadcast
SSID
If disabled, PC users will have to manually enter the SSID and
other details of the wireless interface before they can connect to
this Access Point.
Wireless Security
Current Setting
The current Wireless security is displayed. The default value is
Disabled.
Click this button to access the Wireless security sub-screen, and
view or change the settings. See the following section for details.
Configure
Button
Access Point
Enable this if you want to use Wireless Access Point function.
Enable Wire-
less
If disabled, no Wireless stations can use the Access Point
function, and all connections must be made via the wired LAN.
Access Point
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Use this feature to determine which Wireless stations can use
the Access Point. The options are:
Allow access
by …
•
All Wireless Stations - All wireless stations can use the
access point, provided they have the correct SSID and secu-
rity settings.
•
Trusted Wireless stations only - Only wireless stations
you designate as "Trusted" can use the Access Point, even
if they have the correct SSID and security settings.
This feature uses the MAC address to identify Wireless sta-
tions. The MAC address is a low-level network identifier
which is unique to each PC or network device.
To define the trusted wireless stations, use the "Set Sta-
tions" button.
Click this button to manage the trusted PC database.
Set Stations
Button
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Wireless Security
This screen is accessed by clicking the "Configure" button on the Wireless screen.
There are 3 options for Wireless security:
•
•
•
Disabled - no data encryption is used.
WEP - data is encrypted using the WEP standard.
WPA-PSK - data is encrypted using the WPA-PSK standard. This is a later stan-
dard than WEP, and provides much better security than WEP. If all your Wireless
stations support WPA-PSK, you should use WPA-PSK rather than WEP.
WEP Wireless Security
Figure 8: WEP
Data - WEP Screen
WEP Data Encryption
Select the desired option, and ensure the Wireless Stations use
the same setting.
WEP Data
Encryption
•
64 Bit - data is encrypted, using the default key, before
being transmitted. You must enter at least the default key.
For 64 Bit Encryption, the key size is 10 chars in HEX (0~9
and A~F).
•
128 Bit - data is encrypted, using the default key, before
being transmitted. You must enter at least the default key.
For 128 Bit Encryption, the key size is 26 chars in HEX (0~9
and A~F).
Normally, this should be left at the default value of "Automatic".
If changed to "Open System" or "Shared Key", ensure that your
Wireless Stations use the same setting.
Authentication
Type
Select the key you wish to be the default. Transmitted data is
ALWAYS encrypted using the Default Key; the other Keys are
for decryption only.
Default Key
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
You must enter a Key Value for the Default Key.
Key Value
Enter the key value or values you wish to use. The Default Key
is required, the other keys are optional. Other stations must
have the same key.
If desired, you can generate a key from a phrase, instead of
entering the key value directly. Enter the desired phrase, and
click the "Generate Keys" button.
Passphrase
WPA-PSK Wireless Security
Figure 9: WPA-PSK
Data - WPA-PSK Screen
Security
System
WPA-PSK
Like WEP, data is encrypted before transmission. WPA is
more secure than WEP, and should be used if possible. WPA-
PSK is the version of WPA, which does NOT require a Radius
Server on your LAN.
Enter the PSK (network key). Data is encrypted using a key
derived from the network key. Other Wireless Stations must
use the same network key. The PSK must be from 8 to 63
characters in length.
PSK
The WPA-PSK standard allows different encryption methods to
be used. Wireless Stations must use the same encryption
method.
WPA Encryption
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Trusted Wireless Stations
This feature can be used to prevent unknown Wireless stations from using the Access
Point. This list has no effect unless the setting Allow access by trusted stations only is
enabled.
To change the list of trusted wireless stations, use the Modify List button on the Ac-
cess Control screen. You will see a screen like the sample below.
Figure 10: Trusted Wireless Stations
Data - Trusted Wireless Stations
This lists any Wireless Stations which you have designated
as “Trusted”.
Trusted Wireless
Stations
This list any Wireless Stations detected by the Access Point,
which you have not designated as "Trusted".
Other Wireless
Stations
The name assigned to the Trusted Wireless Station. Use this
when adding or editing a Trusted Station.
Name
The MAC (physical) address of the Trusted Wireless Station.
Use this when adding or editing a Trusted Station.
Address
Buttons
<<
Add a Trusted Wireless Station to the list (move from the
"Other Stations" list).
•
Select an entry (or entries) in the "Other Stations" list,
and click the " << " button.
•
Enter the Address (MAC or physical address) of the
wireless station, and click the "Add" button.
Delete a Trusted Wireless Station from the list (move to the
"Other Stations" list).
>>
•
•
Select an entry (or entries) in the "Trusted Stations" list.
Click the " >> " button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Use this to change an existing entry in the "Trusted Stations"
list:
Edit
1. Select the Station in the Trusted Station list.
2. Click the Edit button. The address will be copied to the
"Address" field, and the Add button will change to Up-
date.
3. Edit the address (MAC or physical address) as required.
4. Click Update to save your changes.
To add a Trusted Station which is not in the "Other Wireless
Stations" list, enter the required data and click this button.
Add (Update)
Clear
When editing an existing Wireless Station, this button will
change from Add to Update.
Clear the Name and Address fields.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Password Screen
The password screen allows you to assign a password to the ADW-4302v2.
Figure 11: Password Screen
Enter the existing password in this field.
Enter the new password here.
Old Password
New password
Re-enter the new password here.
Verify pass-
word
You will be prompted for the password when you connect, as shown below.
Figure 12: Password Dialog
•
•
The "User Name" is always admin
Enter the password for the ADW-4302v2, as set on the Password screen above.
The default password is admin.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Mode Screen
Use this screen to change the mode between Router mode and Modem (Bridge)
mode.
Figure 13: Mode Screen
Select the desired option, and click "Save".
Both the ADSL Modem and the Router features are operational. In
this mode, this device can provide shared Internet Access to all your
LAN users. Also, by default, it acts a DHCP Server, providing an IP
address and related information to all Wireless and LAN users.
Router
Only the ADSL Modem component is operational.
Modem
•
All Router features are disabled. This device is "transparent" - it
does not perform any operations or make any changes to the
network traffic passing through it.
•
•
You need to have a DHCP Server on your LAN to provide IP
addresses to the Wireless clients using this Access Point.
All traffic received on either the Wireless or LAN interface will be
sent over the ADSL connection.
Notes:
•
•
•
Generally, you should NOT use modem mode. Only select this mode if you are
sure this is what you want.
After changing the mode, this device will restart, which will take a few seconds.
The menu will also change, depending on the mode you are in.
The Wireless Access Point can function in either Router or Modem mode. But
generally it is not a good idea to combine a Modem with an Access Point, be-
cause all data received from the wireless stations will be sent over the modem
connection. (Since the modem is transparent, it does not examine the traffic to de-
termine whether the traffic is for the LAN or the WAN.)
•
For details on using Modem Mode, see Chapter 8.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
4
PC Configuration
This Chapter details the PC Configuration required on the local ("Inter-
nal") LAN.
Overview
For each PC, the following may need to be configured:
•
•
•
TCP/IP network settings
Internet Access configuration
Wireless configuration
Windows Clients
This section describes how to configure Windows clients for Internet access via the
ADW-4302v2.
The first step is to check the PC's TCP/IP settings.
The ADW-4302v2 uses the TCP/IP network protocol for all functions, so it is essential
that the TCP/IP protocol be installed and configured on each PC.
TCP/IP Settings - Overview
If using the default ADW-4302v2’s settings, and the default Windows
TCP/IP settings, no changes need to be made.
•
•
By default, the ADW-4302v2 will act as a DHCP Server, automatically providing a
suitable IP Address (and related information) to each PC when the PC boots.
For all non-Server versions of Windows, the default TCP/IP setting is to act as a
DHCP client.
If using a Fixed (specified) IP address, the following changes are re-
quired:
•
•
The Gateway must be set to the IP address of the ADW-4302v2
The DNS should be set to the address provided by your ISP.
If your LAN has a Router, the LAN Administrator must re-
configure the Router itself. Refer to Chapter 8 - Ad-
vanced Setup for details.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Checking TCP/IP Settings - Windows 9x/ME:
5. Select Control Panel - Network. You should see a screen like the following:
Figure 14: Network Configuration
6. Select the TCP/IP protocol for your network card.
7. Click on the Properties button. You should then see a screen like the following.
Figure 15: IP Address (Win 95)
Ensure your TCP/IP settings are correct, as follows:
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the ADW-4302v2
will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the ADW-4302v2.
Using "Specify an IP Address"
If your PC is already configured, check with your network administrator before making
the following changes:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
•
On the Gateway tab, enter the ADW-4302v2's IP address in the New Gateway
field and click Add, as shown below. Your LAN administrator can advise you of the
IP Address they assigned to the ADW-4302v2.
Figure 16: Gateway Tab (Win 95/98)
•
On the DNS Configuration tab, ensure Enable DNS is selected. If the DNS Server
Search Order list is empty, enter the DNS address provided by your ISP in the
fields beside the Add button, then click Add.
Figure 17: DNS Tab (Win 95/98)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Checking TCP/IP Settings - Windows NT4.0
1. Select Control Panel - Network, and, on the Protocols tab, select the TCP/IP
protocol, as shown below.
Figure 18: Windows NT4.0 - TCP/IP
2. Click the Properties button to see a screen like the one below.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Figure 19: Windows NT4.0 - IP Address
3. Select the network card for your LAN.
4. Select the appropriate radio button - Obtain an IP address from a DHCP Server or
Specify an IP Address, as explained below.
Obtain an IP address from a DHCP Server
This is the default Windows setting. Using this is recommended. By default, the
ADW-4302v2 will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the ADW-4302v2.
Specify an IP Address
If your PC is already configured, check with your network administrator before making
the following changes.
1. The Default Gateway must be set to the IP address of the ADW-4302v2. To set
this:
•
•
Click the Advanced button on the screen above.
On the following screen, click the Add button in the Gateways panel, and enter the
ADW-4302v2's IP address, as shown in Figure 20 below.
•
If necessary, use the Up button to make the ADW-4302v2 the first entry in the
Gateways list.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 20 - Windows NT4.0 - Add Gateway
2. The DNS should be set to the address provided by your ISP, as follows:
•
•
Click the DNS tab.
On the DNS screen, shown below, click the Add button (under DNS Service
Search Order), and enter the DNS provided by your ISP.
Figure 21: Windows NT4.0 - DNS
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Checking TCP/IP Settings - Windows 2000:
1. Select Control Panel - Network and Dial-up Connection.
2. Right - click the Local Area Connection icon and select Properties. You should
see a screen like the following:
Figure 22: Network Configuration (Win 2000)
3. Select the TCP/IP protocol for your network card.
4. Click on the Properties button. You should then see a screen like the following.
Figure 23: TCP/IP Properties (Win 2000)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
5. Ensure your TCP/IP settings are correct, as described below.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the ADW-4302v2
will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the ADW-4302v2.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making
the following changes.
•
Enter the ADW-4302v2's IP address in the Default gateway field and click OK.
(Your LAN administrator can advise you of the IP Address they assigned to the
ADW-4302v2.)
•
If the DNS Server fields are empty, select Use the following DNS server ad-
dresses, and enter the DNS address or addresses provided by your ISP, then
click OK.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Checking TCP/IP Settings - Windows XP
1. Select Control Panel - Network Connection.
2. Right click the Local Area Connection and choose Properties. You should see a
screen like the following:
Figure 24: Network Configuration (Windows XP)
3. Select the TCP/IP protocol for your network card.
4. Click on the Properties button. You should then see a screen like the following.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 25: TCP/IP Properties (Windows XP)
5. Ensure your TCP/IP settings are correct.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the ADW-4302v2
will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the ADW-4302v2.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making
the following changes.
•
In the Default gateway field, enter the ADW-4302v2's IP address and click OK.
Your LAN administrator can advise you of the IP Address they assigned to the
ADW-4302v2.
•
If the DNS Server fields are empty, select Use the following DNS server ad-
dresses, and enter the DNS address or addresses provided by your ISP, then
click OK.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Internet Access
To configure your PCs to use the ADW-4302v2 for Internet access:
•
Ensure that the DSL modem, Cable modem, or other permanent connection is
functional.
•
Use the following procedure to configure your Browser to access the Internet via
the LAN, rather than by a Dial-up connection.
For Windows 9x/ME/2000
1. Select Start Menu - Settings - Control Panel - Internet Options.
2. Select the Connection tab, and click the Setup button.
3. Select "I want to set up my Internet connection manually, or I want to connect
through a local area network (LAN)" and click Next.
4. Select "I connect through a local area network (LAN)" and click Next.
5. Ensure all of the boxes on the following Local area network Internet Configuration
screen are unchecked.
6. Check the "No" option when prompted "Do you want to set up an Internet mail
account now?".
7. Click Finish to close the Internet Connection Wizard.
Setup is now completed.
For Windows XP
1. Select Start Menu - Control Panel - Network and Internet Connections.
2. Select Set up or change your Internet Connection.
3. Select the Connection tab, and click the Setup button.
4. Cancel the pop-up "Location Information" screen.
5. Click Next on the "New Connection Wizard" screen.
6. Select "Connect to the Internet" and click Next.
7. Select "Set up my connection manually" and click Next.
8. Check "Connect using a broadband connection that is always on" and click Next.
9. Click Finish to close the New Connection Wizard.
Setup is now completed.
Accessing AOL
To access AOL (America On Line) through the ADW-4302v2, the AOL for Windows
software must be configured to use TCP/IP network access, rather than a dial-up
connection. The configuration process is as follows:
•
Start the AOL for Windows communication software. Ensure that it is Version 2.5,
3.0 or later. This procedure will not work with earlier versions.
•
•
Click the Setup button.
Select Create Location, and change the location name from "New Locality" to"
ADW-4302v2".
•
•
•
Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Num-
ber blank.)
Click Save, then OK.
Configuration is now complete.
Before clicking "Sign On", always ensure that you are using the "ADW-4302v2"
location.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Macintosh Clients
From your Macintosh, you can access the Internet via the ADW-4302v2. The proce-
dure is as follows.
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID
field can be left blank.
4. Close the TCP/IP panel, saving your settings.
Note:
If using manually assigned IP addresses instead of DHCP, the required changes are:
•
•
Set the Router Address field to the ADW-4302v2's IP Address.
Ensure your DNS settings are correct.
Linux Clients
To access the Internet via the ADW-4302v2, it is only necessary to set the ADW-
4302v2 as the "Gateway".
Ensure you are logged in as "root" before attempting any changes.
Fixed IP Address
By default, most Unix installations use a fixed IP Address. If you wish to continue
using a fixed IP Address, make the following changes to your configuration.
•
•
Set your "Default Gateway" to the IP Address of the ADW-4302v2.
Ensure your DNS (Name server) settings are correct.
To act as a DHCP Client (recommended)
The procedure below may vary according to your version of Linux and X -windows
shell.
1. Start your X Windows client.
2. Select Control Panel - Network
3. Select the "Interface" entry for your Network card. Normally, this will be called
"eth0".
4. Click the Edit button, set the "protocol" to "DHCP", and save this data.
5. To apply your changes
•
•
Use the "Deactivate" and "Activate" buttons, if available.
OR, restart your system.
Other Unix Systems
To access the Internet via the ADW-4302v2:
•
Ensure the "Gateway" field for your network card is set to the IP Address of the
ADW-4302v2.
•
Ensure your DNS (Name Server) settings are correct.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Wireless Station Configuration
This section applies to all Wireless stations wishing to use the ADW-4302v2's Access
Point, regardless of the operating system which is used on the client.
To use the Wireless Access Point in the ADW-4302v2, each Wireless Station must
have compatible settings, as follows:
Mode
The mode must be set to Infrastructure (rather than Ad-hoc)
Access points only operate in Infrastructure mode.
This must match the value used on the ADW-4302v2. The default
SSID (ESSID)
value is Wireless.
Note! The SSID is case sensitive.
By default, Wireless security on the ADW-4302v2 is disabled.
Wireless
Security
•
If Wireless security remains disabled on the ADW-4302v2, all
stations must have wireless security disabled.
•
If Wireless security is enabled on the Wireless Router (either
WEP or WPA-PSK), each station must use the same settings
as the ADW-4302v2.
Wireless Configuration on Windows XP
If using Windows XP to configure the Wireless interface on your PC, the configuration
procedure is as follows:
1. Open the Network Connections folder. (Start - Settings - Network Connections).
Figure 26: Network Connections (Windows XP)
2. Right-click the Wireless Network Connection, check that it is enabled (menu
option says Disable, rather than Enable) and then select View Available Wireless
Networks.
3. You will then see a list of wireless networks.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 27 Wireless Networks (Windows XP)
If the "Broadcast SSID" setting on the ADW-4302v2 has
been disabled, its SSID will NOT be listed.
See the following section "If the SSID is not listed" for
details of dealing with this situation.
4. The next step depends on whether or not Wireless security has been enabled on
the ADW-4302v2.
If Wireless Security is Disabled
If Wireless security on the ADW-4302v2 is disabled, Windows will warn you that the
Wireless network is not secure.
Figure 28 Insecure Wireless Network (Windows XP)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
To connect:
•
Check the checkbox Allow me to connect to the selected wireless network, even
though it is not secure.
•
The Connect button will then be available. Click the Connect button, and wait a
few seconds for the connection to be established.
If using WEP Data Encryption
If WEP data encryption has been enabled on the ADW-4302v2, Windows will detect
this, and show a screen like the following.
Figure 29: WEP (Windows XP)
To connect:
•
•
•
•
Enter the WEP key, as set on the ADW-4302v2, in the Network Key field.
Re-enter the WEP key into the Confirm Network key field.
Disable the checkbox Enable IEEE 802.1x authentication for this network.
Click the Connect button.
If this fails, click the Advanced button, to see a screen like the following:
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 30: Advanced - Wireless Networks
Select the SSID for the ADW-4302v2, and click Configure, to see a screen like the
following:
Figure 31: Wireless Network Properties - WEP
Configure this screen as follows:
•
Set Network Authentication to match the ADW-4302v2. (If the setting on the ADW-
4302v2 is "Auto", then either Open or Shared can be used.)
•
For Data Encryption, select WEP.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
•
•
•
For the Network key and Confirm network key, enter the default key value used
on the ADW-4302v2. (Windows will determine if 64bit or 128bit encryption is used.)
The Key index must match the default key index on the ADW-4302v2. The
default value is 1.
Ensure the options The key is provided for me automatically and This is a com-
puter-to-computer (ad hoc) network are unchecked.
•
•
Click OK to save and close this dialog.
This wireless network will now be listed in Preferred Networks on the screen
below.
Figure 32: Preferred Networks
Click OK to establish a connection to the ADW-4302v2.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
If using WPA-PSK Data Encryption
If WPA-PSK data encryption has been enabled on the ADW-4302v2, it does not
matter which network is selected on the screen below. Just click the Advanced button.
Figure 33: Wireless Networks (Windows XP)
You will then see a screen like the example below.
Figure 34: Advanced - Wireless Networks
Select the SSID for the ADW-4302v2, and click Configure, to see a screen like the
following:
42
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Figure 35: Wireless Network Properties- WPA-PSK
Configure this screen as follows:
•
•
•
Set Network Authentication to WPA-PSK.
For Data Encryption, select TKIP.
For the Network key and Confirm network key, enter the network key (PSK) used
on the ADW-4302v2.
•
•
•
Ensure the option This is a computer-to-computer (ad hoc) network is unchecked.
Click OK to save and close this dialog.
This wireless network will now be listed in Preferred Networks on the screen
below.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 36: Preferred Networks
Click OK to establish a connection to the ADW-4302v2.
If the SSID is not listed
If the "Broadcast SSID" setting on the ADW-4302v2 has been disabled, its SSID will
NOT be listed on the screen below.
Figure 37: Wireless Networks (Windows XP)
In this situation, you need to obtain the SSID from your network administrator, then
follow this procedure:
1. Click the Advanced button to see a screen like the example below.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Figure 38: Unlisted Wireless Network
2. Click the Add button. You will see a screen like the example below.
Figure 39: Add Wireless Network
3. Configure this screen as follows:
•
Enter the correct SSID, as used on the ADW-4302v2. Remember the SSID is
case-sensitive, so be sure to match the case, not just the spelling.
•
Set Network Authentication and Data Encryption to match the ADW-4302v2.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
•
•
•
If using data encryption (WEP or WPA-PSK), enter the key used on the ADW-
4302v2. See the preceding sections for details of WEP and WPA-PSK.
Uncheck the options. The key is provided for me automatically and this is a com-
puter-to-computer (ad hoc) network.
Click OK to save and exit.
4. This wireless network will then be listed in Preferred Networks on the screen
below.
Figure 40: Preferred Networks
5. Click OK to establish a connection to the ADW-4302v2.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
5
Operation and Status
This Chapter details the operation of the ADW-4302v2 and the status
screens. For Details of operation in Bridge (Modem) mode, see Chap-
ter 8 - Modem Mode.
Operation - Router Mode
Once both the ADW-4302v2 and the PCs are configured, operation is automatic.
However, there are some situations where additional Internet configuration may be
required. Refer to Chapter 6 - Advanced Features for further details.
Status Screen
Use the Status link on the main menu to view this screen.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 41: Status Screen
Data - Status Screen
ADSL
This indicates the status of the ADSL modem component.
Displays the speed for the DownStream Connection.
Modem Status
DownStream
Connection Speed
If connected, displays the speed for the Up Stream (upload)
ADSL Connection.
UpStream
Connection Speed
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
For each VC (Virtual Circuit), the current status is dis-
played. This will be either "Enabled" or "Disabled".
VC 1 Status
VC 2 Status
Note: VC 1 is a standard (Routed) Internet connection. VC
2, VC 3 and VC 4 are Bridge-mode connections.
VC 3 Status
VC 4 Status
Internet (VC1)
Connection Method
Displays the current connection method, as set in the Setup
Wizard.
This indicates the current status of the Internet Connection
Connection Status
•
•
Active - Connection exists
Idle - No current connection, but no error has been
detected. This condition normally arises when an idle
connection is automatically terminated.
•
Failed - The connection was terminated abnormally.
This could be caused by Modem failure, or the loss of
the connection to the ISP's server.
If there is an error, you can click the "Connection Details"
button to find out more information.
This IP Address is allocated by the ISP (Internet Service
Provider). If using a dynamic IP address, and no connection
currently exists, this information is unavailable.
Internet IP Address
LAN
The IP Address of the ADW-4302v2.
IP Address
Network Mask
The Network Mask (Subnet Mask) for the IP Address
above.
This shows the status of the DHCP Server function. The
value will be "Enabled" or "Disabled".
DHCP Server
MAC Address
This shows the MAC Address for the ADW-4302v2, as
seen on the LAN interface.
Wireless
If using an ESS (Extended Service Set, with multiple ac-
cess points) this ID is called an ESSID (Extended Service
Set Identifier).
Name (SSID)
The current region, as set on the Wireless screen.
Region
This shows the Channel currently used, as set on the
Wireless screen.
Channel
This indicates whether or not the Wireless Access Point
feature is enabled.
Wireless AP
This indicates whether or not the SSID is Broadcast. This
setting is on the Wireless screen.
Broadcast Name
System
The current name of the Router. This name is also the
"hostname" for users with an "@Home" type connection.
Device Name
49
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
The version of the current firmware installed.
Firmware Version
Buttons
Click this button to open a sub-window and view the details
of each VC (Virtual Circuit).
ADSL Details
Click this button to open a sub-window and view a detailed
description of the current connection. Depending on the
type of connection, a "log" may also be available.
Connection Details
This will open a sub-window, showing all LAN and Wireless
devices currently on the network.
Attached Devices
Refresh Screen
Update the data displayed on screen.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
Connection Status - PPPoE & PPPoA
If using PPPoE (PPP over Ethernet) or PPPoA (PPP over ATM), a screen like the
following example will be displayed when the "Connection Details" button is clicked.
Figure 42: PPPoE Status Screen
Data - PPPoE/PPPoA Screen
This indicates how long the current connection has been
established.
Connection Time
This indicates whether or not the connection is currently
established.
PPPoE Link Status
•
If the connection does not exist, the "Connect" button
can be used to establish a connection.
•
If the connection currently exists, the "Disconnect"
button can be used to break the connection.
This indicates the status of the PPPoE Server login.
Negotiation
IP Address
The IP Address of this device, as seen by Internet users.
This address is allocated by your ISP (Internet Service
Provider).
The Network Mask associated with the IP Address above.
Network Mask
Buttons
If not connected, establish a connection to your ISP.
If connected to your ISP, hang up the connection.
Close this window.
Connect
Disconnect
Close
51
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Connection Details - Dynamic IP Address
If your access method is "Direct" (no login), with a Dynamic IP address, a screen like
the following example will be displayed when the "Connection Details" button is
clicked.
Figure 43: Connection Details - Fixed/Dynamic IP Address
Data - Dynamic IP address
Internet
The current IP Address of this device, as seen by Internet
users. This address is allocated by your ISP (Internet Service
Provider).
IP Address
The Network Mask associated with the IP Address above.
Network Mask
The IP address of the remote Gateway or Router associated
with the IP Address above.
Default Gateway
The IP address of your ISP's DHCP Server.
DHCP Server
DNS Server
The IP address of the Domain Name Server which is currently
used.
This indicates when the current IP address was obtained, and
how long before this IP address allocation (the DCHP lease)
expires.
Lease Obtained
Lease Expires
Buttons
Release
If an IP Address has been allocated to the ADW-4302v2 (by
the ISP's DHCP Server, clicking the "Release" button will
break the connection and release the IP Address.
If the ISP's DHCP Server has NOT allocated an IP Address for
the ADW-4302v2, clicking the "Renew" button will attempt to
re-establish the connection and obtain an IP Address from the
ISP's DHCP Server.
Renew
Close
Close this window.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
53
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Connection Details - Fixed IP Address
If your access method is "Direct" (no login), with a fixed IP address, a screen like the
following example will be displayed when the "Connection Details" button is clicked.
Figure 44: Connection Details - Fixed/Dynamic IP Address
Data - Fixed IP address Screen
Internet
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
IP Address
The Network Mask associated with the IP Address above.
Network Mask
The IP Address of the remote Gateway or Router associated
with the IP Address above.
Default Gateway
The IP Address of the Domain Name Server which is currently
used.
DNS Server
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
6
Advanced Features
This Chapter explains when and how to use the ADW-4302v2's "Ad-
vanced" Features.
Overview
The following advanced features are provided:
•
Access Control
•
•
Internet Access
Trusted PCs
•
Internet:
•
•
•
DMZ
Special Applications
URL filter
•
•
•
•
•
•
•
Dynamic DNS
Firewall Rules
Firewall Services
Schedule
Virtual Servers
VPN
SNMP
Access Control
The Access Control feature allows administrators to restrict the Internet Access avail-
able to PCs on your LAN by MAC address. With the default settings, everyone has
unrestricted Internet access.
Access Control Screen
To view this screen, select the Access Control link on the Advanced menu.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 45: Access Control Screen
Data - Access Control Screen
Internet Access
Select the desired options for Internet access control:
Access control
•
•
Disable - Nothing is blocked.
Block all Internet access - All traffic via the WAN port is
blocked.
•
Block selected Services - You can select which Ser-
vices are to block. Hold CTRL key (on MAC, SHIFT) to
select multiple items.
The administrator can choose Default Schedule to apply the
blocking only during scheduled times. (If access is not
blocked, no Scheduling is possible, and this setting has no
effect.)
Schedule
•
•
None - Schedule is disabled.
Default - Use the schedule which is defined in Schedule
of Advanced Features.
Trusted PCs
Restrictions do not apply to Trusted PCs.
Set Trusted PCs
Trusted PCs
This Trusted PC list has no effect unless the Internet Access feature is enabled. The
list on the Trusted PCs will be bypassed from blockade of Internet access.
To change the list of trusted PCs, click the Set Trusted PCs button on the Access
Control screen. You will see a screen like the sample below.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 46: Trusted PCs
Data - Trusted PCs
Trusted PCs
This lists any PCs which you have designated as “Trusted”.
Trusted PCs
This list any PCs detected by the router, which you have not
designated as "Trusted".
Other PCs
Buttons
<<
Add a Trusted PC to the list (move from the "Other PCs" list).
•
Select an entry (or entries) in the "Other PCs" list, and
click the " << " button.
Delete a Trusted PC from the list (move to the "Other PCs"
list).
>>
•
•
Select an entry (or entries) in the "Trusted PCs" list.
Click the " >> " button.
Note:
It is necessary to click the Save button in the Access Control page for activation of
Trusted PCs if you add/delete any entry of Trusted PCs page.
Internet
This screen provides access to the DMZ, Special Applications and URL Filter features.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 49: Internet Screen
DMZ
This feature, if enabled, allows the DMZ computer on your LAN to be exposed to all
users on the Internet.
•
•
•
This allows almost any application to be used on the "DMZ PC".
The "DMZ PC" will receive all "Unknown" connections and data.
If the DMZ feature is enabled, you must select the PC to be used as the "DMZ
PC".
The "DMZ PC" is effectively outside the Firewall, mak-
ing it more vulnerable to attacks. For this reason, you
should only enable the DMZ feature when required.
Special Applications
If you use Internet applications which use non-standard connections or port numbers,
you may find that they do not function correctly because they are blocked by the
ADW-4302v2. In this case, you can define the application as a "Special Application".
The Special Applications screen can be reached by clicking the Special Applications
button on the Internet screen.
You can then define your Special Applications. You will need detailed information
about the application; this is normally available from the supplier of the application.
Also, note that the terms "Incoming" and "Outgoing" on this screen refer to traffic from
the client (PC) viewpoint
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 50: Special Applications Screen
Data - Special Applications Screen
Use this to Enable or Disable this Special Application as required.
Enter a descriptive name to identify this Special Application.
Checkbox
Name
•
Type - Select the protocol (TCP or UDP) used when you receive
data from the special application or service. (Note: Some applica-
tions use different protocols for outgoing and incoming data).
Incoming
Ports
•
Start - Enter the beginning of the range of port numbers used by
the application server, for data you receive. If the application
uses a single port number, enter it in both the "Start" and "Finish"
fields.
•
•
•
Finish - Enter the end of the range of port numbers used by the
application server, for data you receive.
Type - Select the protocol (TCP or UDP) used when you send
data to the remote system or service.
Outgoing
Ports
Start - Enter the beginning of the range of port numbers used by
the application server, for data you send to it. If the application
uses a single port number, enter it in both the "Start" and "Finish"
fields.
•
Finish - Enter the end of the range of port numbers used by the
application server, for data you send to it. If the application uses
a single port number, enter it in both the "Start" and "Finish"
fields.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Using a Special Application
•
Configure the Special Applications screen as required.
•
On your PC, use the application normally. Remember that only one (1) PC can
use each Special application at any time. Also, when 1 PC is finished using a par-
ticular Special Application, there may need to be a "Time-out" before another PC
can use the same Special Application. The "Time-out" period may be up to 3 min-
utes.
URL Filter
If you want to limit access to certain sites on the Internet, you can use this feature.
The URL filter will check each Web site access. If the address, or part of the address,
is included in the block site list, access will be denied.
On the Advanced Internet screen, select the desired setting:
•
•
•
•
Disable - disable this feature.
Block By Schedule - block according to the settings on the Schedule page.
Block Always - allow blocking all of the time, independent of the Schedule page.
Allow Trusted PCs to Visit Blocked Sites - Enable this to allow specified com-
puter(s) to have unrestricted access to the Internet. For this/these PC(s), the URL
filter will be ignored.
To change the list of trusted PCs, click the Set Trusted PCs button on the Access
Control screen. See Figure 46.
Data - Trusted PCs
Trusted PCs
This lists any PCs which you have designated as “Trusted”.
Trusted PCs
Other PCs
This list any PCs detected by the router, which you have not
designated as "Trusted".
Buttons
<<
Add a Trusted PC to the list (move from the "Other PCs" list).
•
Select an entry (or entries) in the "Other PCs" list, and
click the " << " button.
Delete a Trusted PC from the list (move to the "Other PCs"
list).
>>
•
•
Select an entry (or entries) in the "Trusted PCs" list.
Click the " >> " button.
Click the URL Filter List button to open the URL Filter screen, allowing you to create
or modify the filter strings which determine which sites will be blocked.
The URL Filter List screen is displayed when the URL Filter List button on the
Advanced Internet screen is clicked.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Note:
It is necessary to click the Save button in the Access Control page for activation of
Trusted PCs if you add/delete any entry of Trusted PCs page.
Figure 51: URL Filter Screen
Data - URL Filter Screen
Current Filter Strings
The list contains the current list of items to block.
Current Filter
Strings
•
•
•
To add to the list, use the "Add" option below.
To delete an entry, select it and click Delete button.
To delete all entries, click the Delete All button.
To add to the current list, type the word or domain name you
want to block into the field provided, then click the Add button.
Add Filter
String
Filter strings should be as specific as possible. Otherwise, you
may block access to many more sites than intended.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Dynamic DNS (Domain Name Server)
This free service is very useful when combined with the Virtual Server feature. It
allows Internet users to connect to your Virtual Servers using a URL, rather than an IP
Address.
This also solves the problem of having a dynamic IP address. With a dynamic IP
address, your IP address may change whenever you connect, which makes it difficult
to connect to you.
DDNS Services work as follows:
1. You must register for the service at one of the listed DDNS Service providers.
2. After registration, use the Service provider's normal procedure to obtain your
desired Domain name.
3. Enter your DDNS data on the ADW-4302v2's DDNS screen, and enable the
DDNS feature.
4. The ADW-4302v2 will then automatically ensure that your current IP Address is
recorded at the DDNS service provider's Domain Name Server.
5. From the Internet, users will be able to connect to your Virtual Servers (or DMZ
PC) using your Domain name, as shown on this screen.
Dynamic DNS Screen
Select Advanced on the main menu, then Dynamic DNS, to see a screen like the
following:
Figure 52: DDNS Screen
Data - Dynamic DNS Screen
DDNS Service
Use this to enable or disable the DDNS feature as required.
Use a Dynamic
DNS Service
Select the desired DDNS Service provider.
Service Provider
Web Site
Click this button to open a new window and connect to the
Web site of the selected DDNS service provider.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
DDNS Data
Host Name
Enter the domain name allocated to you by the DDNS Service.
If you have more than one name, enter the name you wish to
use.
Enter your Username for the DDNS Service. (TZO.com uses
your E-mail address.)
User Name
Password
Enter your current password for the DDNS Service. (TZO.com
calls this a key.)
Enter the domain name allocated to you by the DDNS Service.
If you have more than one name, enter the name you wish to
use.
Domain Name
DDNS Status
•
•
•
This message is returned by the DDNS Server.
Normally, this message should be "Update successful"
If the message indicates some problem, you need to
connect to the DDNS Service provider and correct this
problem.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Firewall Rules
The Firewall Rules screen allows you to define "Firewall Rules" which can allow or
prevent certain traffic. "Traffic" means incoming connection attempts, not packets.
By default:
•
•
All Outgoing traffic is permitted.
All Incoming traffic is denied.
Because of this default behavior, any Outgoing rules will generally Block traffic, and
Incoming rules will generally Allow traffic.
Firewall Rules Screen
An example screen is shown below.
Figure 53: Firewall Screen
Data - Firewall Rules
Incoming Rules
For the default rule, this will display "Default".
For rules which you create, this will display a radio button
which allows you to select the rule.
#
Indicates whether or not the rule is currently enabled.
Enable
For rules you have added, this column will contain a checkbox,
allowing you to easily enable or disable the rule. (Click "Save"
after making any changes.)
The Service covered by this rule.
Service Name
Action
The action performed on connections which are covered by
this rule.
The PC or Server on your LAN to which traffic covered by this
rule will be sent.
LAN Server
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
The WAN IP address or addresses covered by this rule.
WAN Users
Log
Indicates whether or not connections covered by this rule
should be logged.
Use the Add button to create a new rule.
Buttons
The other buttons - Edit, Move, or Delete - require that a rule
be selected first. Use the radio buttons in the left column to
select the desired rule.
Outgoing Rules
#
For the default rule, this will display "Default".
For rules which you create, this will display a radio button
which allows you to select the rule.
Indicates whether or not the rule is currently enabled.
Enable
For rules you have added, this column will contain a checkbox,
allowing you to easily enable or disable the rule. (Click "Save"
after making any changes.)
The Service covered by this rule.
Service Name
Action
The action performed on connections which are covered by
this rule.
The LAN PC or PCs covered by this rule.
LAN Users
WAN Servers
Log
The WAN IP address or addresses covered by this rule.
Indicates whether or not connections covered by this rule
should be logged.
Use the Add button to create a new rule.
Buttons
The other buttons - Edit, Move, or Delete - require that a rule
be selected first. Use the radio buttons in the left column to
select the desired rule.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Incoming Rules (Inbound Services)
This screen is displayed when the "Add" or "Edit" button for Incoming Rules is clicked.
Figure 54: Inbound Services Screen
Data - Incoming Rules Screen
Inbound Services
Select the desired Service. This determines which packets are
Service
covered by this rule. If necessary, you can define a new Service
on the "Services" screen, by defining the protocols and port num-
bers used by the Service.
Select the desired action for packets covered by this rule:
Action
•
•
•
•
ALLOW always
ALLOW by schedule, otherwise Block
BLOCK always
BLOCK by schedule, otherwise Allow
Note:
•
Any inbound traffic which is not allowed by rules you create
will be blocked by the Default rule.
•
BLOCK rules are only useful if the traffic is already covered by
an ALLOW rule. (That is, you wish to block a sub-set of traffic
which is currently allowed by another rule.)
•
To define the Schedule used in these selections, use the
"Schedule" screen.
Select the PC or Server on your LAN which will receive the in-
bound traffic covered by this rule.
Send to
LAN Server
These settings determine which packets are covered by the rule,
based on their source (WAN) IP address. Select the desired
option:
WAN Users
•
•
Any - All IP addresses are covered by this rule.
Address range - If this option is selected, you must enter the
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
desired values in the "Single/Start" and "Finish" fields to de-
termine the address range.
•
Single address - Enter the required address in the "Sin-
gle/Start" fields.
This determines whether packets covered by this rule are logged.
Select the desired action.
Log
•
•
•
•
Always - always log traffic considered by this rule, whether it
matches or not. (This is useful when debugging your rules.)
Never - never log traffic considered by this rule, whether it
matches or not.
Match - Log traffic only it matches this rule. (The action is
determined by this rule.)
Not Match - Log traffic which is considered by this rule, but
does not match (The action is NOT determined by this rule.)
Outgoing Rules (Outbound Services)
This screen is displayed when the "Add" or "Edit" button for Outgoing Rules is clicked.
Figure 55: Outbound Services Screen
Data - Outbound Rules Screen
Outbound Services
Select the desired Service or application to be covered by this
rule. If the desired service or application does not appear in the
list, you must define it using the "Services" menu option
Service
Select the desired action for packets covered by this rule:
Action
•
•
•
BLOCK always
BLOCK by schedule, otherwise Allow
ALLOW always
67
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
•
ALLOW by schedule, otherwise Block
Note:
•
Any outbound traffic which is not blocked by rules you create
will be allowed by the Default rule.
•
ALLOW rules are only useful if the traffic is already covered
by a BLOCK rule. (That is, you wish to allow a subset of traffic
which is currently blocked by another rule.)
•
To define the Schedule used in these selections, use the
"Schedule" screen.
Select the desired option to determine which PCs are covered by
this rule:
LAN Users
•
•
Any - All PCs are covered by this rule.
Single PC - Only the selected PC is covered by this rule.
If selected, you must select the PC.
PC - If using Single PC above, select the PC or Server on your
LAN which will be covered by this rule.
These settings determine which packets are covered by the rule,
based on their source (WAN) IP address. Select the desired
option:
WAN Users
•
•
Any - All IP addresses are covered by this rule.
Address range - If this option is selected, you must enter the
"Start" and "Finish" fields.
•
Single address - Enter the required address in the "Sin-
gle/Start" fields.
This determines whether packets covered by this rule are logged.
Select the desired action.
Log
•
•
•
•
Always - always log traffic considered by this rule, whether it
matches or not. (This is useful when debugging your rules.)
Never - never log traffic considered by this rule, whether it
matches or not.
Match - Log traffic only it matches this rule. (The action is
determined by this rule.)
Not Match - Log traffic which is considered by this rule, but
does not match (The action is NOT determined by this rule.)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Firewall Services
Services are used when creating Firewall Rules.
If you wish to create a firewall rule, but the required service is not listed in the "Ser-
vice" list, you can use this feature to define the required service or services. Once
created, these services will be listed in the "Service" list, and can be used when
creating Firewall Rules.
Figure 56: Add Services Screen
Data - Firewall Services
Services
This lists any Services you have defined. If you have not
defined any Services, this list will be empty.
Existing Ser-
vices
Once you define some services, they will be listed here, and
also shown in the Service list used to create Firewall rules.
(Firewall services are at the end of the list, after the pre-
defined services.)
Use this to open a sub-screen where you can add a new
service.
Add
To modify a service, select it, and then click this button.
Edit
Use this button to delete the selected service. You can delete
any services you have defined.
Delete
69
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Add/Edit Service
This screen is displayed when the Add or Edit button on the Services screen is
clicked.
Figure 57: Add/Edit Service
Data - Add/Edit Service
Services
If editing, this shows the current name of the Service.
If adding a new service, this will be blank, and you should
enter a suitable name.
Name
Select the protocol used by the Service.
Type
Enter the beginning of the port range used by the Service.
Enter the end of the port range used by the Service.
Start Port
Finish Port
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Options
This screen allows advanced users to enter or change a number of settings. For
normal operation, there is no need to use this screen or change any settings.
An example Options screen is shown below.
Figure 58: Options Screen
Data - Options Screen
Internet
Respond to
Ping
•
If checked, the Wireless Router will respond to Ping (ICMP)
packets received from the Internet.
•
If not checked, Ping (ICMP) packets from the Internet will be
ignored. Disabling this option provides a slight increase in
security.
Enter a value between 1 and 1500.
MTU Size
Note: MTU (Maximum Transmission Unit) size should only be
changed if advised to do so by Technical Support.
UPnP
UPnP
•
UPnP (Universal Plug and Play) allows automatic discovery
and configuration of equipment attached to your LAN. UPnP
is by supported Windows ME, XP, or later.
•
•
If Enabled, this device will be visible via UPnP.
If Disabled, this device will not be visible via UPnP.
Enter the desired value, in minutes. The valid range is from 1 to
1440.
Advertisement
Period
Enter the desired value, in hops. The valid range is from 1 to
255.
Advertisement
Time to Live
71
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Schedule
This Schedule can be used for the Firewall Rules and the URL filter.
Figure 59: Schedule Screen
Data - Schedule Screen
Schedule
Each day of the week can scheduled independently.
Day
Two (2) separate sessions or periods can be defined. Session
2 can be left blank if not required.
Session 1
Session 2
Enter the start using a 24 hr clock.
Start Time
Finish Time
Local Time
Time Zone
Enter the finish time using a 24 hr clock.
In order to display your local time correctly, you must select
your "Time Zone" from the list.
If your region uses Daylight Savings Time, you must manually
check "Adjust for Daylight Savings Time" at the beginning of
the adjustment period, and uncheck it at the end of the Day-
light Savings period.
Adjust for Day-
light Savings
Time
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
If you prefer to use a particular NTP server as the primary
NTP server, check the checkbox "Use this NTP Server" and
enter the Server's IP address in the fields provided.
Use this NTP
Server
If this setting is not enabled, the default NTP Servers is used.
This displays the current time on the ADW-4302v2, at the time
the page is loaded.
Current Time
73
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Virtual Servers
This feature, sometimes called Port Forwarding, allows you to make Servers on your
LAN accessible to Internet users. Normally, Internet users would not be able to ac-
cess a server on your LAN because:
•
•
Your Server does not have a valid external IP Address.
Attempts to connect to devices on your LAN are blocked by the firewall in this
device.
The "Virtual Server" feature solves these problems and allows Internet users to con-
nect to your servers, as illustrated below.
Figure 60: Virtual Servers
IP Address seen by Internet Users
Note that, in this illustration, both Internet users are connecting to the same IP Ad-
dress, but using different protocols.
To Internet users, all virtual Servers on your LAN have the same IP Address.
This IP Address is allocated by your ISP.
This address should be static, rather than dynamic, to make it easier for Internet users
to connect to your Servers.
However, you can use the DDNS (Dynamic DNS) feature to allow users to connect to
your Virtual Servers using a URL, instead of an IP Address.
Virtual Servers Screen
•
•
The "Virtual Servers" feature allows Internet Users to access PCs on your LAN.
The PCs must be running the appropriate Server Software.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
•
•
For Internet Users, ALL of your Servers have the same IP address. This IP ad-
dress is allocated by your ISP.
To make it easier for Internet users to connect to your Servers, you can use the
"DDNS" feature. This allows Internet users to connect to your Servers with a URL,
rather than an IP address. This technology works even if your ISP allocates dy-
namic IP addresses (IP address is allocated upon connection, so it may change
each time you connect).
Figure 61: Virtual Servers Screen
Data - Virtual Servers Screen
Servers
This lists a number of common Server types. If the desired
Servers
Server type is not listed, you can create a Firewall Rule to
achieve the same effect as the Virtual Server function.
Properties
Enable
Use this to Enable or Disable support for this Server, as
required.
If Enabled, you must select the PC to which this traffic will be
sent.
Select the PC for this Server. The PC must be running the
appropriate Server software.
PC (Server)
75
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
For each entry, the PC must be running the appropri-
ate Server software.
If the desired Server type is not listed, you can define
your own Servers, using the Firewall Rules.
Connecting to the Virtual Servers
Once configured, anyone on the Internet can connect to your Virtual Servers. They
must use the Internet IP Address (the IP Address allocated to you by your ISP).
e.g.
http://203.70.212.52
ftp://203.70.212.52
It is more convenient if you are using a Fixed IP Address from your ISP, rather than
Dynamic. However, you can use the Dynamic DNS feature to allow users to connect
to your Virtual Servers using a URL, rather than an IP Address.
From the Internet, ALL Virtual Servers have
the IP Address allocated by your ISP
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
VPN (IPSec)
The VPN (Virtual Private Network) feature in the ADW-4302v2 allows you to create a
VPN connection between 2 ADW-4302v2s, or a remote PC to establish a VPN con-
nection to the ADW-4302v2.
To establish a VPN connection from a remote PC to the ADW-4302v2, you need
suitable (IPSec) VPN client software on your PC.
For more information about VPNs, please refer to Appendix C - About VPNs.
VPN Policies
A "VPN Policy" contains all the configuration data for a particular VPN connection.
Generally, you will have to create one policy for each site you wish to connect to. The
remote VPN Gateway (or client) needs to have matching configuration.
•
•
•
Traffic covered by an enabled policy will automatically be sent via a VPN tunnel. If
the VPN tunnel does not exist, it will be created.
The VPN tunnel is created according to the parameters in the SA (Security Asso-
ciation).
The remote VPN Endpoint must have a matching SA, or it will refuse the connec-
tion.
There are 2 types of VPN Policies:
•
Manual - All settings (including the keys) for the VPN tunnel are manually input at
each end (both VPN Endpoints).
•
Auto - Some parameters for the VPN tunnel are generated automatically. This
requires using the IKE (Internet Key Exchange) protocol to perform negotiations
between the 2 VPN Endpoints.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
VPN Policies Screen
This screen is displayed when you select VPN on the Advanced menu. It allows you
to create, modify and manage your VPN Policies.
If you have not created any policies, the Policy Table will be empty.
Figure 62: VPN Policies Screen
Data - VPN Policies Screen
The Policy Table contains the following data
Policy Table
•
Enable - Use this checkbox to Enable or Disable a Policy
as required. Click "Save" after making any changes.
•
Name - Each policy is given a unique name to identify it.
This name is not known to the remote VPN endpoint; it is
used only to assist managing your policies.
•
•
Endpoint - The address of the remote VPN endpoint.
Type - The Type is "Auto" or "Manual" as explained
above.
•
•
•
Local LAN - IP address or subnet on your local LAN.
Traffic must be from (or to) these addresses to be cov-
ered by this policy.
Remote LAN - IP address or subnet on the remote LAN.
Traffic must be to (or from) these addresses to be cov-
ered by this policy.
ESP - ESP (Encapsulating Security Payload) encryption
protocol used for the VPN data.
Buttons
Save
Save any changes to the "Enable" setting for each policy.
Edit (modify) the selected policy. (Select a policy by clicking
on the radio button.)
Edit
Delete the selected policy. (Select a policy by clicking on the
radio button.)
Delete
Change to the input screen for an "Auto" policy. See the
following section for details.
Add Auto Policy
When the new policy is saved, it will appear in the bottom
row of the Policy Table.
Change to the input screen for a "Manual" policy. See the
following section for details.
Add Manual Pol-
icy
When the new policy is saved, it will appear in the bottom
row of the Policy Table.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
View details of each current VPN Tunnel (connection) in a
sub-window. You also have the option of viewing the VPN
Log.
VPN Status
VPN Auto Policy Screen
This screen is displayed when you click the Add Auto Policy button on the VPN Poli-
cies screen, or when you edit an existing Auto Policy. It allows you to define or edit an
"Auto" VPN policy.
An "Auto" VPN policy uses the IKE (Internet Key Protocol) to exchange and negotiate
parameters for the IPSec SA (Security Association). Because of this negotiation, it is
not necessary for all settings on this VPN Gateway to match the settings on the re-
mote VPN endpoint. Where settings must match, this is indicated.
Figure 63: VPN-Auto Policy Screen
79
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Data - VPN-Auto Policy Screen
General
Enter a unique name to identify this policy. This name is not
Policy Name
supplied to the remote VPN endpoint. It is used only to help
you manage the policies.
If the remote endpoint has a dynamic IP address, select
"Dynamic IP address". No "Address Data" input is required.
Otherwise, select the desired option (IP address or Domain
Name) and enter the address of the remote VPN endpoint
you wish to connect to.
Remote VPN
Endpoint
Note: The remote VPN endpoint must have this VPN Gate-
way's address entered as its "Remote VPN Endpoint".
Check this if you wish NETBIOS traffic to be forwarded over
the VPN tunnel. The NETBIOS protocol is used by Microsoft
Networking.
NetBIOS Enable
Local LAN
Local LAN
This identifies which PCs on your LAN are covered by this
policy. For each selection, data must be provided as follows:
•
Single address
Enter an IP address in the "IP address" field. Typically,
this setting is used when you wish to make a single
Server on your LAN available to remote users.
•
Subnet address
Enter an IP address in the "IP address" field, and the de-
sired network mask in the "Subnet Mask" field.
The remote VPN endpoint must have these IP addresses
entered as its "Remote" addresses.
Remote LAN
Remote LAN
This identifies which PCs on the remote LAN are covered by
this policy. For each selection, data must be provided as
follows:
•
Single PC - no subnet
Select this option if there is no LAN (only a single PC) at
the remote endpoint. If this option is selected, no addi-
tional data is required.
•
Single address
Enter an IP address in the "IP address" field. This must
be an address on the remote LAN. Typically, this setting
is used when you wish to access a server on the remote
LAN.
•
Subnet address
Enter an IP address in the "IP address" field, and the de-
sired network mask in the "Subnet Mask" field.
The remote VPN endpoint must have these IP addresses
entered as its "Local" addresses.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
IKE
This setting is used when determining if the IKE policy
matches the current traffic. Select the desired option.
Direction
•
Responder only - Incoming connections are allowed, but
outgoing connections will be blocked.
•
Initiator and Responder - Both incoming and outgoing
connections are allowed.
IPSec has 2 possibilities - "Main Mode" and "Aggressive
Mode".
Exchange Mode
Currently, only "Main Mode" is supported. Ensure the remote
VPN endpoint is set to use "Main Mode".
The Diffie-Hellman algorithm is used when exchanging keys.
The DH Group setting determines the number of bit size
used in the exchange. This value must match the value used
on the remote VPN Gateway.
Diffie-Hellman
(DH) Group
Select the desired option to match the "Remote Identity
Type" setting on the remote VPN endpoint.
Local Identity
Type
•
•
•
WAN IP Address - your Internet IP address.
Fully Qualified Domain Name - your domain name.
Fully Qualified User Name - your name, E-mail address,
or other ID.
Select the desired option to match the "Local Identity Type"
setting on the remote VPN endpoint.
Remote Identity
Type
•
•
•
IP Address - The Internet IP address of the remote VPN
endpoint.
Fully Qualified Domain Name - the Domain name of the
remote VPN endpoint.
Fully Qualified User Name - the name, E-mail address, or
other ID of the remote VPN endpoint.
Enter the data for the selection above. (If "IP Address" is
selected, no input is required.)
Remote Identity
Data
SA Parameters
Encryption
Encryption Algorithm used for both IKE and IPSec. This
setting must match the setting used on the remote VPN
Gateway.
Authentication Algorithm used for both IKE and IPSec. This
setting must match the setting used on the remote VPN
Gateway.
Authentication
Pre-shared Key
SA Life Time
The key must be entered both here and on the remote VPN
Gateway. This method does not require using a CA (Certifi-
cate Authority).
This determines the time interval before the SA (Security
Association) expires. (It will automatically be re-established if
necessary.) While using a short time period (or data amount)
increases security, it also degrades performance. It is com-
mon to use periods over an hour (3600 seconds) for the SA
Life Time. This setting applies to both IKE and IPSec SAs.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
If enabled, security is enhanced by ensuring that the key is
changed at regular intervals. Also, even if one key is broken,
subsequent keys are no easier to break. (Each key has no
relationship to the previous key.)
IPSec PFS (Per-
fect Forward
Secrecy)
This setting applies to both IKE and IPSec SAs. When con-
figuring the remote endpoint to match this setting, you may
have to specify the "Key Group" used. For this device, the
"Key Group" is the same as the "DH Group" setting in the IKE
section.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
VPN- Manual Policy Screen
This screen is displayed when you click the Add Manual Policy button on the VPN
Policies screen, or when you edit an existing Manual Policy. It allows you to define or
edit a "Manual" VPN policy.
A "Manual" VPN policy requires that you enter all data on both VPN endpoints. There
is no negotiation between the 2 VPN endpoints.
Figure 64: VPN-Manual Policy Screen
Data - VPN-Manual Policy Screen
General
Enter a unique name to identify this policy. This name is not
supplied to the remote VPN endpoint. It is used only to help
you manage the policies.
Policy Name
Select the desired option (IP address or Domain Name) and
enter the address of the remote VPN endpoint you wish to
connect to.
Remote VPN
Endpoint
Note: The remote VPN endpoint must have this VPN Gate-
way's address entered as its "Remote VPN Endpoint".
83
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Check this if you wish NETBIOS traffic to be forwarded over
the VPN tunnel. The NETBIOS protocol is used by Microsoft
Networking.
NETBIOS Enable
Local LAN
Local LAN
This identifies which PCs on your LAN are covered by this
policy. For each selection, data must be provided as follows:
•
Single address
Enter an IP address in the "IP address" field. Typically, this
setting is used when you wish to make a single Server on
your LAN available to remote users.
•
Subnet address
Enter an IP address in the "IP address" field, and the de-
sired network mask in the "Subnet Mask" field.
The remote VPN endpoint must have these IP addresses
entered as its "Remote" addresses.
Remote LAN
Remote LAN
This identifies which PCs on the remote LAN are covered by
this policy. For each selection, data must be provided as
follows:
•
Single PC - no subnet
Select this option if there is no LAN (only a single PC) at
the remote endpoint. If this option is selected, no additional
data is required.
•
Single address
Enter an IP address in the "IP address" field. This must be
an address on the remote LAN. Typically, this setting is
used when you wish to access a server on the remote
LAN.
•
Subnet address
Enter an IP address in the "IP address" field, and the de-
sired network mask in the "Subnet Mask" field.
The remote VPN endpoint must have these IP addresses
entered as its "Local" addresses.
ESP Configuration
SPI
Enter the required SPIs. Each policy must have unique SPIs.
These settings must match the remote VPN endpoint. Note
that the "in" setting here must match the "out" setting on the
remote VPN endpoint, and the "out" setting here must match
the "in" setting on the remote VPN endpoint.
Select the desired Encryption Algorithm, and enter the key in
the field provided.
Encryption
•
For DES, the key should be 8 ASCII characters (16 Hex
characters).
•
For 3DES, the key should be 24 ASCII characters (48 Hex
characters).
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Select the desired Authentication Algorithm, and enter the key
in the field provided.
Authentication
•
For MD5, the key should be 16 ASCII characters (32 Hex
characters).
•
For SHA-1, the key should be 20 ASCII (40 Hex charac-
ters).
85
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
VPN Status Screen
This screen is displayed when you click the VPN Log button on the VPN Policies
screen, or on the Status screen.
This screen allows you to view details of each current VPN Tunnel (connection). If
there are no current connections, the status table will be empty.
Figure 65: VPN-Status Screen
Data - VPN Status Screen
This table contains the following data about each current connec-
tion.
Tunnel Table
•
•
•
Policy Name - The name of the policy. When a policy is
created, it must be given a unique name to identify it.
Remote Endpoint - The address of the remote VPN end-
point.
SPI (In) - This is a unique index number to identify the incom-
ing connection. For "Auto" policies, the SPI is automatically
generated. For "Manual" policies, the SPI must be entered
when the policy is configured.
•
•
SPI (Out) - This is a unique index number to identify the
outgoing connection. For "Auto" policies, the SPI is automati-
cally generated. For "Manual" policies, the SPI must be
entered when the policy is configured.
Action - This column will contain a button which allows you to
break (terminate) the current the VPN connection.
Buttons
Use this to Enable or Disable auto-refresh for this screen. If
enabled, the screen will be updated every few seconds.
Auto Refresh
The status bar on the bottom on the screen will indicate if auto-
refresh is enabled or disabled.
Click this button to switch to the VPN log screen.
VPN Log
The VPN log shows details of each connection as it is created.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Microsoft VPN
Microsoft VPN uses the Microsoft VPN Adapter which is provided in recent versions of
Windows. This feature can be used to provide remote access to your LAN by individ-
ual PCs. This method provides an alternative to using IPSec VPN, which is described
in the previous chapter. Using Microsoft VPN provides easier setup than using IPSec
VPN.
Microsoft VPN Screen
ADW-4302v2 incorporates a PPTP (Peer-to-Peer Tunneling Protocol) server which is
compatible with the "VPN Adapter" provided with recent versions of Microsoft Win-
dows. Remote Windows clients are able to connect to this Server. Once connected,
they can access the LAN as if they connected locally.
This screen is displayed when you select Microsoft VPN on the Advanced menu.
Figure 66: Microsoft VPN Screen
87
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Data – Microsoft VPN Screen
PPTP Server
Use this checkbox to enable or disable this feature as required.
Enable
To allow connection by remote Windows clients, you must
enable this feature, and enter the client details (on the Clients
screen) to allow them to login to this Server.
Use this checkbox to enable or disable this feature as required.
Auto-disconnect
Idle Time-out
To disconnect PPTP connection automatically when the login
time reach the idle time.
Remote Users
Login Name
Enter the login name. The remote user must provide this name
when they connect. The name must not contain spaces, punc-
tuation, or special characters.
Enter the login password. The remote user must provide this
password when they connect.
Login Password
Re-enter the password above.
Verify Password
Buttons
Click this button to open a sub-window and view the details of
each current PPTP connection.
VPN Server
Status
Use this to delete the selected user if required.
Use this to delete whole users.
Delete
Delete All
Add User
Use this to save the data in the "Properties" area as a new
entry. (If a user is selected in the "Existing User" list, the selec-
tion is ignored.)
Use this to prepare the form for a new entry. Any existing data
will be cleared.
Clear Form
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
VPN Server Status Screen
This screen is displayed when you click the VPN Server Status button on the Micro-
soft VPN screen.
Figure 67: Microsoft VPN Status Screen
Data - Microsoft VPN Status Screen
This table contains the following data about each current con-
nection.
Connection
Table
•
•
•
User Name – The login name.
Remote IP - The IP address of the remote client.
Local IP –ADW-4302v2 will allocate a local IP address to
remote client when user login.
•
•
Start Time – This displays the start time when remote client
login to the ADW-4302v2.
Action - This column will contain a button which allows you
to break (terminate) the PPTP connection.
Server Log
Auto Refresh
Use this to Enable or Disable auto-refresh for this screen. If
enabled, the screen will be updated every few seconds.
The status bar on the bottom on the screen will indicate if auto-
refresh is enabled or disabled.
View Log
This displays details of each connection or connection attempt.
You can use the Clear Log button to re-start the log, making new
messages easier to read.
Windows Client Setup
To connect to the PPTP (VPN) Server in the VPN Broadband Gateway:
•
The Microsoft VPN feature in the VPN Broadband Gateway must be enabled and
configured, as described in the previous section.
•
Each user must have a login (username and password) on the VPN client data-
base on the VPN Broadband Gateway.
•
•
The remote client PC must be configured as described in the following sections.
It is assumed that remote users have a Broadband (not dial-up) connection to the
Internet.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Windows 98/ME
1. Click Start - Settings - Dial-up Networking
2. Select Make New Connection
3. Type a name for this connection, and ensure that "Microsoft VPN Adapter" is
selected. Click "Next" to continue.
Figure 68: Windows ME VPN Adapter
4. Enter the Internet IP address or domain name of this device. (If you don't have a
fixed IP address, you can use a Dynamic DNS service to obtain a domain name.)
Click "Next" to continue.
Figure 69: Windows ME VPN Remote Host
5. Click "Finish" to exit the Wizard.
The new entry will now be listed in "Dial-up Networking".
If necessary, you can change the settings for this connection by right-clicking on it,
and selecting Properties.
To force all outgoing traffic to be sent via VPN, enable the setting This is the default
Internet connection on the Dialing tab. (Do NOT enable this setting if using Dial-up or
PPPoE client software.)
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 70: Windows ME VPN Dialing Properties
To establish a connection:
1. Ensure you are connected to the Internet.
2. Select Start - Settings - Dial-up Networking
3. Double-click the new VPN entry in Dial-up Networking.
4. Enter your User name and Password, as recorded in the Client database on
ADW-4302v2.
5. Click the "Connect" button.
Windows 2000
Ensure you have logged on with Administrator rights before attempting this procedure.
1. Open "Network Connections", and start the "New Connection" Wizard.
2. Select the VPN option ("Connect to a private network through the Internet"), as
shown below, and click Next.
Figure 71: Windows 2000 Network Connection
91
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
3. On the screen below:
•
•
Select "Do not dial the initial connection" if Internet access is via the LAN.
If using a PPPoE software client, select "Automatically dial this initial connec-
tion" and select the PPPoE connection.
•
Click Next to continue.
Figure 72: Windows 2000 Public Network
4. On the screen below, enter the Domain Name or Internet IP address of ADW-
4302v2 you wish to connect to. Click Next to continue.
Figure 73: Windows 2000 VPN Host
5. Choose whether to allow this connection for everyone, or only for yourself, as
required. Click Next to continue.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 74: Windows 2000 Connection Availability
6. Enter a suitable name, and click "Finish" to save and exit.
Figure 75: Windows 2000 Finish Wizard
Setup is now complete.
To establish a connection:
1
2
Right-click the connection in "Network Connections", and select "Connect".
You will then be prompted for the username and password. Enter the username
and password assigned to you, as recorded in the VPN client database on ADW-
4302v2.
3
You can choose to have Windows remember the password if desired, so you do
not have to enter it again.
Changing the connection settings
The PPTP (VPN) Server in ADW-4302v2 is designed to work with the default Win-
dows settings.
•
If necessary, you can change the Windows settings by right-clicking the VPN
connection in Network Connections, and selecting Properties.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
•
The Properties dialog has a Networking tab with a "Type of VPN" setting. If you
have trouble connecting, you can change this setting from "Automatic" to "PPTP
VPN".
Windows XP
Ensure you have logged on with Administrator rights before attempting this procedure.
1. Open Network Connections (Start-Settings-Network Connections), and start the
New Connection Wizard.
2. Select the option "Connect to the network at my workplace", as shown below, and
click Next.
Figure 76: Windows XP Network Connection Type
3. On the next screen, shown below, select the "Virtual Private Network connection"
option. Click Next to continue.
Figure 77: Windows XP Network Connection
4. Enter a suitable name for this connection.
Click Next to continue.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 78: Windows XP Connection Name
5. On the screen below, select "Do not dial the initial connection".
Click Next to continue.
Figure 79: Windows XP Public Network
6. On the screen below, enter the Domain Name or Internet IP address of ADW-
4302v2 you wish to connect to. Click Next to continue.
Figure 80: Windows XP VPN Server
95
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
7. Choose whether to allow this connection for everyone, or only for yourself, as
required. Click Next to continue.
Figure 81: Windows XP Connection Availability
8. On the final screen, click Finish to save and exit.
Setup is now complete.
To establish a connection:
1
2
Right-click the connection in "Network Connections", and select "Connect".
You will then be prompted for the username and password. Enter the username
and password assigned to you, as recorded in the VPN client database on ADW-
4302v2.
3
You can choose to have Windows remember the password if desired, so you do
not have to enter it again.
Changing the connection settings
The PPTP (VPN) Server in ADW-4302v2 is designed to work with the default Win-
dows settings.
•
If necessary, you can change the Windows settings by right-clicking the VPN
connection in Network Connections, and selecting Properties.
•
The Properties dialog has a Networking tab with a "Type of VPN" setting. If you
have trouble connecting, you can change this setting from "Automatic" to "PPTP
VPN".
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
SNMP
Simple Network Management Protocol (SNMP) is the protocol which enable adminis-
trator to monitor network and bandwidth usage as well as various other network
parameters like system information and port usages, providing system administrators
with live readings and periodical usage trends to optimize the network efficiency.
SNMP Screen
Select Advanced on the main menu, then SNMP, to see a screen like the following:
Figure 82: SNMP Screen
Data - SNMP Screen
SNMP Service
Enable or disable the SNMP feature as required.
Enable SNMP
support
SNMP Data
Enter the Community Name as the Read Community which
SNMP Software will use it to access ADW-4302v2. Once the
string name is matched, user will be able to view the SNMP
data.
Community
Name
Specify a name in any string to be the System Contact.
Specify a name in any string to be the System Name.
Specify a name in any string to be the System Location.
SysContact
SysName
SysLocation
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
7
Advanced Administration
This Chapter explains the settings available via the "Administration"
section of the menu.
Overview
Normally, it is not necessary to use these screens, or change any settings. These
screens and settings are provided to deal with non-standard situations, or to provide
additional options for advanced users.
The available settings and features are:
This is the list of PCs shown when you select the "DMZ PC"
or a "Virtual Server". This database is maintained automati-
cally, but you can add and delete entries for PCs which use
a Fixed (Static) IP Address.
PC Database
Backup or restore the configuration file for the ADW-
4302v2. This file contains all the configuration data.
Config File
View or clear all logs, set E-Mailing of log files and alerts.
Perform a Ping or DNS Lookup.
Logging & Email
Diagnostics
Allow settings to be changed from the Internet.
Only required if your LAN has other Routers or Gateways.
Remote Admin
Routing
Upgrade the Firmware (software) installed in your ADW-
4302v2.
Upgrade Firmware
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
PC Database
The PC Database is used whenever you need to select a PC (e.g. for the "DMZ" PC).
•
•
It eliminates the need to enter IP addresses.
Also, you do not need to use fixed IP addresses on your LAN.
However, if you do use a fixed IP address on some devices on your LAN, you should
enter details of each such device into the PC database, using the PC Database
screen.
PC Database Screen
An example PC Database screen is shown below.
Figure 83: PC Database
•
•
•
PCs which are "DHCP Clients" are automatically added to the database, and
updated as required.
By default, non-Server versions of Windows act as "DHCP Clients"; this setting is
called "Obtain an IP Address automatically".
The ADW-4302v2 uses the "Hardware Address" to identify each PC, not the name
or IP address. The "Hardware Address" can only change if you change the PC's
network card or adapter.
•
This system means you do NOT need to use Fixed (static) IP addresses on your
LAN. However, you can add PCs using Fixed (static) IP Addresses to the PC da-
tabase if required.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Data - PC Database Screen
This lists all current entries. Data displayed is name (IP Address)
Known PCs
type. The "type" indicates whether the PC is connected to the
LAN.
If adding a new PC to the list, enter its name here. It is best if
this matches the PC's "hostname".
Name
Enter the IP Address of the PC. The PC will be sent a "ping" to
determine its hardware address. If the PC is not available (not
connected, or not powered On) you will not be able to add it.
IP Address
Buttons
Add
This will add the new PC to the list. The PC will be sent a "ping"
to determine its hardware address. If the PC is not available (not
connected, or not powered On) you will not be able to add it.
Delete the selected PC from the list. This should be done in 2
situations:
Delete
•
•
The PC has been removed from your LAN.
The entry is incorrect.
Update the data on screen.
Refresh
Display a read-only list showing full details of all entries in the
PC database.
Generate
Report
Advanced
View the Advanced version of the PC database screen - PC
Administration Database (Admin). See below for details.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
PC Database - Advanced
This screen is displayed if the "Advanced Administration" button on the PC Database
is clicked. It provides more control than the standard PC Database screen.
Figure 84: PC Database (Admin)
Data - Advanced PC Database
This lists all current entries. Data displayed is name (IP Address)
type. The "type" indicates whether the PC is connected to the
LAN.
Known PCs
PC Properties
Name
If adding a new PC to the list, enter its name here. It is best if
this matches the PC's "hostname".
101
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Select the appropriate option:
IP Address
•
Automatic - The PC is set to be a DHCP client (Windows:
"Obtain an IP address automatically"). The ADW-4302v2 will
allocate an IP address to this PC when requested to do so.
The IP address could change, but normally won't.
•
DCHP Client - Reserved IP Address - Select this if the PC
is set to be a DCHP client, and you wish to guarantee that
the ADW-4302v2 will always allocate the same IP Address
to this PC.
Enter the required IP address.
•
Fixed IP Address - Select this if the PC is using a Fixed
(Static) IP address. Enter the IP address allocated to the
PC. (The PC itself must be configured to use this IP ad-
dress.)
Select the appropriate option
MAC Address
•
Automatic discovery - Select this to have the ADW-4302v2
contact the PC and find its MAC address. This is only possi-
ble if the PC is connected to the LAN and powered On.
•
MAC address is - Enter the MAC address on the PC. The
MAC address is also called the "Hardware Address", "Physi-
cal Address", or "Network Adapter Address". The ADW-
4302v2 uses this to provide a unique identifier for each PC.
Because of this, the MAC address can NOT be left blank.
Buttons
Add a new PC to the list, using the data in the "Properties" box.
If "Automatic discovery" (for MAC address) is selected, the PC
will be sent a "ping" to determine its hardware address. This will
fail unless the PC is connected to the LAN, and powered on.
Add as New
Entry
Update (modify) the selected PC, using the data in the "Proper-
ties" box.
Update Se-
lected PC
Clear the "Properties" box, ready for entering data for a new PC.
Update the data on screen.
Clear Form
Refresh
Display a read-only list showing full details of all entries in the
PC database.
Generate
Report
Standard
Screen
Click this to view the standard PC Database screen.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Config File
This feature allows you to download the current settings from the ADW-4302v2, and
save them to a file on your PC.
You can restore a previously-downloaded configuration file to the ADW-4302v2, by
uploading it to the ADW-4302v2.
This screen also allows you to set the ADW-4302v2 back to its factory default configu-
ration. Any existing settings will be deleted.
An example Config File screen is shown below.
Figure 85: Config File Screen
Data - Config File Screen
Use this to download a copy of the current configuration, and
Backup Config
store the file on your PC. Click Download to start the download.
This allows you to restore a previously-saved configuration file
back to the ADW-4302v2.
Restore Config
Click Browse to select the configuration file, then click Restore to
upload the configuration file.
WARNING !
Uploading a configuration file will destroy (overwrite) ALL of the
existing settings.
Clicking the Factory Defaults button will reset the ADW-4302v2
Default Config
to its factory default settings.
WARNING !
This will delete ALL of the existing settings.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Logging
The Logs record various types of activity on the ADW-4302v2. This data is useful for
troubleshooting, but enabling all logs will generate a large amount of data and ad-
versely affect performance.
Since only a limited amount of log data can be stored in the ADW-4302v2, log data
can also be E-mailed to your PC. Use the E-mail screen to configure this feature.
Figure 86: Logging Screen
Data - Logging Screen
Logs
The current time on the ADW-4302v2 is displayed.
Current log data is displayed in this panel.
There are three (3) buttons
Current Time
Log Data
Buttons
•
•
Refresh - Update the log data.
Clear Log - Clear the log, and restart it. This makes
new messages easier to read.
•
Send Log - E-mail the log immediately. This is only
functional if the E-mail screen has been configured.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Logs
Use these checkboxes to determine which events are
included in the log. Checking all options will increase the
size of the log, so it is good practice to disable any events
which are not really required.
Include (Check-
boxes)
•
Attempted access to blocked sites - If checked,
attempted Internet accesses which were blocked are
logged.
•
Connections to the Web-based interface of this
Router - If checked, this will log connections TO this
Router, rather than through this Router to the Internet.
•
•
Router operation - If checked, other Router operations
(not covered by the selections above) will be logged.
Known DoS attacks and Port Scans - If checked,
Denial of Service attacks, as well as port scans, will be
logged.
Syslog
Data is not sent to a Syslog Server.
Disable
The Syslog data is broadcast, rather than sent to a specific
Syslog server. Use this if your Syslog Server does not have
a fixed IP address.
Broadcast on LAN
If your Syslog server has a fixed IP address, select this
option, and enter the IP address of your Syslog server.
Syslog
105
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
E-mail
This screen allows you to E-mail Logs and Alerts. A sample screen is shown below.
Figure 87: E-mail Screen
Data - E-mail Screen
E-Mail Notification
Check this box to enable this feature. If enabled, the E-mail
address information (below) must be provided.
Turn E-mail
Notification on
Enter the E-mail address the Log is to be sent to. The E-mail
will also show this address as the Sender's address.
Send to this E-
mail address
Enter the address or IP address of the SMTP (Simple Mail
Transport Protocol) Server you use for outgoing E-mail.
Outgoing
(SMTP) Mail
Server
To stop spanners, many SMTP mail servers require you to log
in to send mail. In this case, enable this checkbox, and enter
the login information (User name and Password) in the fields
below.
My SMTP Mail
Server requires
authentication
If you have enabled "My SMTP Mail Server requires authenti-
cation" above, enter the User Name required to login to your
SMTP Server.
User Name
Password
If you have enabled "My SMTP Mail Server requires authenti-
cation" above, enter the password required to login to your
SMTP Server.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
E-mail Alerts
You can choose to have alerts E-mailed to you, by checking
the desired checkboxes. The ADW-4302v2 can send an im-
mediate alert when it detects a significant security incident
such as
Send E-mail
alerts immedi-
ately
•
•
A known hacker attack is directed at your IP address
A computer on the Internet scans your IP address for open
ports
•
Someone on your LAN (Local Area Network) tries to visit a
blocked site.
E-mail Logs
Send Logs
Select the desired option for sending the log by E-mail.
•
Never (default) - This feature is disabled; Logs are not
sent.
•
When log is full - The time is not fixed. The log will be
sent when the log is full, which will depend on the volume
of traffic.
•
•
•
Hourly, Daily, Weekly... - The log is sent on the interval
specified.
If Daily is selected, the log is sent at the time specified.
Select the time of day you wish the E-mail to be sent.
If Weekly is selected, the log is sent once per week, on the
specified day, at the specified time.
Select the day and the time of day you wish the E-mail to
be sent.
Note:
If the log is full before the time specified to send it, it will be
sent regardless of the day and time specified.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Diagnostics
This screen allows you to perform a "Ping" or a "DNS lookup". These activities can be
useful in solving network problems.
An example Network Diagnostics screen is shown below.
Figure 88: Network Diagnostics Screen
Data - Network Diagnostics Screen
Ping
Enter the IP address you wish to ping. The IP address can be
on your LAN, or on the Internet. Note that if the address is on
the Internet, and no connection currently exists, you could get
a "Timeout" error. In that case, wait a few seconds and try
again.
Ping this
IP Address
After entering the IP address, click this button to start the
"Ping" procedure. The results will be displayed in the Ping
Results pane.
Ping Button
DNS Lookup
Internet name
Enter the Domain name or URL for which you want a DNS
(Domain Name Server) lookup. Note that if the address in on
the Internet, and no connection currently exists, you could get
a "Timeout" error. In that case, wait a few seconds and try
again.
After entering the Domain name/URL, click this button to start
the "DNS Lookup" procedure.
Lookup Button
Routing
Display
Click this button to display the internal routing table. This
information can be used by Technical Support and other staff
who understand Routing Tables.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Remote Administration
If enabled, this feature allows you to manage the ADW-4302v2 via the Internet.
Figure 89: Remote Administration Screen
Data - Remote Administration Screen
Remote Administration
Check to allow administration/management via the Internet.
(To connect, see below).
Enable Remote
Management
If Disabled, this device will ignore Administration connection
attempts from the Internet.
This is the current address you will use when accessing this
device from the Internet. To connect, see details and an ex-
ample below.
Current
IP Address
Enter a port number between 1 and 65535. The default for
HTTP (Web) connections is port 80, but using port 80 will
prevent the use of a Web "Virtual Server" on your LAN. So
using a different port number is recommended. The default
value is 8080.
Port Number
The port number must be specified in your Browser when you
connect. See the following section for details.
Access Permission
Select the desired option.
Allow Remote
Access
•
•
Everyone - allow access by everyone on the Internet.
Only This Computer - allow access by only one IP ad-
dress. Enter the desired IP address.
•
IP Address Range - allow access from a range of IP
addresses on the Internet. Enter a beginning and ending
IP address to define the allowed range.
For security, you should restrict access to as few external IP
addresses as practical.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
To connect from a remote PC via the Internet
1. Ensure your Internet connection is established, and start your Web Browser.
2
In the "Address" bar, enter "HTTP://" followed by the Internet IP Address of the
ADW-4302v2. If the port number is not 80, the port number is also required. (After
the IP Address, enter ":" followed by the port number.)
e.g.
HTTP://123.123.123.123:8080
This example assumes the WAN IP Address is 123.123.123.123, and the port
number is 8080.
3
You will then be prompted for the login name and password for this device.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Routing
Overview
•
•
•
If you don't have other Routers or Gateways on your LAN, you can ignore the
"Routing" page completely.
If the ADW-4302v2 is only acting as a Gateway for the local LAN segment, ignore
the "Routing" page even if your LAN has other Routers.
If your LAN has a standard Router (e.g. Cisco) on your LAN, and the ADW-
4302v2 is to act as a Gateway for all LAN segments, enable RIP (Routing Infor-
mation Protocol) and ignore the Static Routing table.
•
•
If your LAN has other Gateways and Routers, and you wish to control which LAN
segments use each Gateway, do NOT enable RIP (Routing Information Protocol).
Configure the Static Routing table instead. (You also need to configure the other
Routers.)
If using Windows 2000 Data center Server as a software Router, enable RIP on
the ADW-4302v2, and ensure the following Windows 2000 settings are correct:
•
•
Open Routing and Remote Access
In the console tree, select Routing and Remote Access , [server name], IP
Routing, RIP
•
•
In the "Details" pane, right-click the interface you want to configure for RIP ver-
sion 2, and then click "Properties".
On the "General" tab, set Outgoing packet protocol to "RIP version 2 broadcast",
and Incoming packet protocol to "RIP version 1 and 2".
Routing Screen
The routing table is accessed by the Routing link on the Administration menu.
Using this Screen
Generally, you will use either RIP (Routing Information Protocol) OR the Static Rout-
ing Table, as explained above, although is it possible to use both methods
simultaneously.
Static Routing Table
•
If RIP is not used, an entry in the routing table is required for each LAN segment
on your Network, other than the segment to which this device is attached.
•
The other Routers must also be configured. See Configuring Other Routers on
your LAN later in this chapter for further details and an example.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Figure 90: Routing Screen
Data - Routing Screen
RIP
Select the desired RIP Direction.
RIP Direction
RIP Version
Choose the RIP Version for the Server.
Static Routing
This list shows all entries in the Routing Table.
Static Routing
Table Entries
•
•
This area shows details of the selected item in the list.
Change any the properties as required, then click the
"Edit" button to save the changes to the selected entry.
Buttons
Add
Add a new entry to the Static Routing table, using the data
shown in the "Properties" area on screen. The entry selected
in the list is ignored, and has no effect.
Update the current Static Routing Table entry, using the data
shown in the table area on screen.
Edit
Delete the current Static Routing Table entry.
Delete
Save
Save the RIP setting. This has no effect on the Static Routing
Table.
Configuring Other Routers on your LAN
It is essential that all IP packets for devices not on the local LAN be passed to the
ADW-4302v2, so that they can be forwarded to the external LAN, WAN, or Internet.
To achieve this, the local LAN must be configured to use the ADW-4302v2 as the
Default Route or Default Gateway.
Local Router
The local router is the Router installed on the same LAN segment as the ADW-4302v2.
This router requires that the Default Route is the ADW-4302v2 itself. Typically, routers
have a special entry for the Default Route. It should be configured as follows.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Normally 0.0.0.0, but check your router documenta-
tion.
Destination IP Address
Network Mask
Normally 0.0.0.0, but check your router documenta-
tion.
The IP Address of the ADW-4302v2.
1
Gateway IP Address
Metric
Other Routers on the Local LAN
Other routers on the local LAN must use the ADW-4302v2's Local Router as the
Default Route. The entries will be the same as the ADW-4302v2's local router, with
the exception of the Gateway IP Address.
•
For a router with a direct connection to the ADW-4302v2's local Router, the Gate-
way IP Address is the address of the ADW-4302v2's local router.
•
For routers which must forward packets to another router before reaching the
ADW-4302v2's local router, the Gateway IP Address is the address of the inter-
mediate router.
Static Routing - Example
Figure 91: Routing Example
For the ADW-4302v2's Routing Table
For the LAN shown above, with 2 routers and 3 LAN segments, the ADW-4302v2
requires 2 entries as follows.
Entry 1 (Segment 1)
Destination IP Address
Network Mask
192.168.1.0
255.255.255.0 (Standard Class C)
Gateway IP Address
192.168.0.100 (ADW-4302v2's local
Router)
Metric
2
113
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Entry 2 (Segment 2)
Destination IP Address
Network Mask
192.168.2.0
255.255.255.0 (Standard Class C)
Gateway IP Address
Metric
192.168.0.100
3
For Router A's Default Route
Destination IP Address
Network Mask
0.0.0.0
0.0.0.0
Gateway IP Address
192.168.0.1 (ADW-4302v2's IP Address)
For Router B's Default Route
Destination IP Address
Network Mask
0.0.0.0
0.0.0.0
Gateway IP Address
192.168.1.80 (ADW-4302v2's local router)
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Upgrade Firmware
The firmware (software) in the ADW-4302v2 can be upgraded using your Web
Browser.
You must first download the upgrade file, then select Upgrade Firmware on the Ad-
ministration menu. You will see a screen like the following.
Figure 92: Router Upgrade Screen
To perform the Firmware Upgrade:
1. Click the Browse button and navigate to the location of the upgrade file.
4
5
Select the upgrade file. Its name will appear in the Upgrade File field.
Click the Upload button to commence the firmware upgrade.
The ADW-4302v2 is unavailable during the upgrade
process, and must restart when the upgrade is
completed. Any connections to or through the ADW-
4302v2 will be lost.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
8
Modem Mode
This Chapter explains configuration and operation when in "Modem" or
"Bridge" mode..
Overview
There are two modes available on the Mode screen.
•
Router - Both the ADSL Modem and the Router features are operational. In this
mode, this device can provide shared Internet Access to all your LAN users. Also,
by default, it acts a DHCP Server, providing an IP address and related information
to all Wireless and LAN users.
•
Modem - Only the ADSL Modem component is operational. All Router features
are disabled. This device is "transparent" - it does not perform any operations or
make any changes to the network traffic passing through it. You need to have a
DHCP Server on your LAN to provide IP addresses to the Wireless clients using
this Access Point.
This Chapter describes operation while in Modem Mode, also called Bridge Mode.
Management Connections
When this device restarts in Modem mode, the IP address does not change, but the
DHCP server is disabled. However, your PC will usually retain the IP address pro-
vided by the DHCP Server, so the connection will be automatically re-established. You
then need to ensure that the IP address of this modem is suitable for your LAN.
•
You need to have a DHCP Server on your LAN to provide IP addresses to the
Wireless clients using this Access Point.
•
This Modem/AP must be a valid device on your LAN, to allow management con-
nections. You must assign a (fixed) IP address which is within the address range
used on your LAN, but not within the address range used by your DHCP server.
When you connect in future, just connect normally, using the IP address you assigned.
1. Start your WEB browser.
6
In the Address box, enter "HTTP://" and the current IP Address of the ADW-
4302v2, as in this example, which uses the ADW-4302v2's default IP Address:
HTTP://192.168.0.1
7
When prompted for the User name and Password, enter adminfor the user name,
and the current password, as set on the password screen. (The password is the
same regardless of the mode.)
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Home Screen
If in Modem mode, the home screen will look like the example below.
Figure 93: Home Screen - Modem Mode
Note that the menu has changed, many of the options in Router mode are not avail-
able. The screens available are:
•
Mode - change back to Router mode, if desired.
•
LAN - set IP address, mask and gateway. This is the same as in Router mode,
except that the DHCP server is not available while in Modem mode.
•
•
•
•
Wireless - this screen, and related sub-screens, is the same as in Router mode.
Password - this screen is the same as in Router mode.
Upgrade Firmware - this screen is the same as in Router mode.
Status - displays current settings and status. See the following section for details.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Mode Screen
This screen is change back to Router mode, if desired.
Figure 94: Mode Screen
Data - Mode Screen
This field displays the current name of this device.
Device
Name
Select the desired device mode for the router:
Device
Mode
•
•
Router - Both the ADSL Modem and the Router features are
operational. In this mode, this device can provide shared Inter-
net Access to all your LAN users. Also, by default, it acts a
DHCP Server, providing an IP address and related information
to all Wireless and LAN users.
Modem - Only the ADSL Modem component is operational. All
Router features are disabled. This device is "transparent" - it
does not perform any operations or make any changes to the
network traffic passing through it. You need to have a DHCP
Server on your LAN to provide IP addresses to the Wireless cli-
ents using this Access Point.
This mode is also called Bridge Mode.
After changing the mode, this device will restart, which will take a
few seconds. The menu will also change, depending on the mode
you are in.
Operation
Operation is automatic and transparent.
•
Wireless clients can connect to the Access Point if they have the correct SSID
and security, but they must obtain an IP address from the DHCP Server on your
LAN.
•
The modem will act like any other ADSL modem. No routing will be performed,
and no client login will be done. If a client login is required, it must be performed
by your Router/Gateway or by software on your PC.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Status Screen
In Modem mode, the Status screen looks like the example below.
Figure 95: Status Screen - Bridge Mode
Data - Status Screen (Bridge Mode)
System
The current name of the Router. This name is also the
Device Name
"hostname" for users with a "@Home" type connection.
The version of the current firmware installed.
Firmware Version
ADSL
This indicates the status of the ADSL modem component.
Displays the speed for the DownStream Connection.
Modem Status
DownStream
Connection Speed
119
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
If connected, displays the speed for the Up Stream (upload)
ADSL Connection.
UpStream
Connection Speed
For each VC (Virtual Circuit), the current status is dis-
played. This will be either "Enabled" or "Disabled".
VC 1 Status
VC 2 Status
VC 3 Status
VC 4 Status
Click this button to open a sub-window and view the details
of each VC (Virtual Circuit).
ADSL Details
LAN
The IP Address of the ADW-4302v2.
IP Address
Network Mask
The Network Mask (Subnet Mask) for the IP Address
above.
This shows the MAC Address for the ADW-4302v2, as
seen on the LAN interface.
MAC Address
Wireless
If using an ESS (Extended Service Set, with multiple ac-
cess points) this ID is called an ESSID (Extended Service
Set Identifier).
Name (SSID)
The current region, as set on the Wireless screen.
Region
This shows the Channel currently used, as set on the
Wireless screen.
Channel
This indicates whether or not the Wireless Access Point
feature is enabled.
Wireless AP
This indicates whether or not the SSID is Broadcast. This
setting is on the Wireless screen.
Broadcast Name
Clicking this will generate a list of all devices currently using
the Access Point.
Associated
Devices
Buttons
View the details of each VC (Virtual Circuit).
ADSL Details
Associated Devices
Clicking this will generate a list of all devices currently using
the Access Point.
Update the data displayed on screen.
Refresh Screen
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Troubleshooting
This Appendix covers the most likely problems and their solutions.
Overview
This chapter covers some common problems that may be encountered while using
the ADW-4302v2 and some possible solutions to them. If you follow the suggested
steps and the ADW-4302v2 still does not function properly, contact your dealer for
further advice.
General Problems
Problem 1: Can't connect to the ADW-4302v2 to configure it.
Check the following:
Solution 1:
•
The ADW-4302v2 is properly installed, LAN connections are OK,
and it is powered ON.
•
Ensure that your PC and the ADW-4302v2 are on the same
network segment. (If you don't have a router, this must be the
case.)
•
•
If your PC is set to "Obtain an IP Address automatically" (DHCP
client), restart it.
If your PC uses a Fixed (Static) IP address, ensure that it is using
an IP Address within the range 192.168.0.2 to 192.168.0.254 and
thus compatible with the ADW-4302v2's default IP Address of
192.168.0.1.
Also, the Network Mask should be set to 255.255.255.0 to match
the ADW-4302v2.
In Windows, you can check these settings by using Control
Panel-Network to check the Properties for the TCP/IP protocol.
Internet Access
Problem 1: When I enter a URL or IP address I get a time out error.
A number of things could be causing this. Try the following trouble-
shooting steps.
Solution 1:
•
Check if other PCs work. If they do, ensure that your PCs IP
settings are correct. If using a Fixed (Static) IP Address, check
the Network Mask, Default gateway and DNS as well as the IP
Address.
•
If the PCs are configured correctly, but still not working, check
the ADW-4302v2. Ensure that it is connected and ON. Connect
to it and check its settings. (If you can't connect to it, check the
LAN and power connections.)
121
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
•
Check the ADW-4302v2's status screen to see if it is working
correctly.
Problem 2: Some applications do not run properly when using the ADW-
4302v2.
The ADW-4302v2 processes the data passing through it, so it is not
transparent.
Solution 2:
For incoming connections, you must use the Virtual Server or Fire-
wall Rules to specify the PC which will receive the incoming traffic.
You can also use the DMZ function. This should work with almost
every application, but:
•
•
It is a security risk, since the firewall is disabled.
Only one (1) PC can use this feature.
Wireless Access
Problem 1: My PC can't locate the Wireless Access Point.
Check the following.
Solution 1:
•
Your PC is set to Infrastructure Mode. (Access Points are always
in Infrastructure Mode)
•
The SSID on your PC and the Wireless Access Point are the
same.
Remember that the SSID is case-sensitive. So, for example
"Workgroup" does NOT match "workgroup".
•
Both your PC and the ADW-4302v2 must have the same setting
for WEP. The default setting for the ADW-4302v2 is disabled, so
your wireless station should also have WEP disabled.
•
•
If WEP is enabled on the ADW-4302v2, your PC must have WEP
enabled, and the key must match.
If the ADW-4302v2's Wireless screen is set to Allow Trusted PCs
only, then each of your Wireless stations must have been desig-
nated as "Trusted", or the Wireless station will be blocked.
•
To see if radio interference is causing a problem, see if connec-
tion is possible when close to the ADW-4302v2.
Remember that the connection range can be as little as 100 feet
in poor environments.
Problem 2: Wireless connection speed is very slow.
The wireless system will connect at the highest possible speed,
depending on the distance and the environment. To obtain the high-
est possible connection speed, you can experiment with the
following:
Solution 2:
•
ADW-4302v2 location.
Try adjusting the location and orientation of the ADW-4302v2.
•
Wireless Channel
If interference is the problem, changing to another channel may
show a marked improvement.
•
Radio Interference
Other devices may be causing interference. You can experiment
by switching other devices Off, and see if this helps. Any "noisy"
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Troubleshooting
devices should be shielded or relocated.
•
RF Shielding
Your environment may tend to block transmission between the
wireless stations. This will mean high access speed is only pos-
sible when close to the ADW-4302v2.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
B
About Wireless LANs
This Appendix provides some background information about using
Wireless LANs (WLANs).
Modes
Wireless LANs can work in either of two (2) modes:
•
•
Ad-hoc
Infrastructure
Ad-hoc Mode
Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wire-
less Stations (e.g. notebook PCs with wireless cards) communicate directly with
each other.
Infrastructure Mode
In Infrastructure Mode, one or more Access Points are used to connect Wireless
Stations (e.g. Notebook PCs with wireless cards) to a wired (Ethernet) LAN. The
Wireless Stations can then access all LAN resources.
Access Points can only function in "Infrastructure" mode,
and can communicate only with Wireless Stations which are
set to "Infrastructure" mode.
BSS/ESS
BSS
A group of Wireless Stations and a single Access Point, all using the same ID (SSID),
form a Basic Service Set (BSS).
Using the same SSID is essential. Devices with different SSIDs are unable to com-
municate with each other.
ESS
A group of Wireless Stations, and multiple Access Points, all using the same ID
(ESSID), form an Extended Service Set (ESS).
Different Access Points within an ESS can use different Channels. In fact, to reduce
interference, it is recommended that adjacent Access Points SHOULD use different
channels.
As Wireless Stations are physically moved through the area covered by an ESS, they
will automatically change to the Access Point which has the least interference or best
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - About Wireless LANs
performance. This capability is called Roaming. (Access Points do not have or require
Roaming capabilities.)
Channels
The Wireless Channel sets the radio frequency used for communication.
•
Access Points use a fixed Channel. You can select the Channel used. This allows
you to choose a Channel which provides the least interference and best perform-
ance. In the USA and Canada, 11 channel are available. If using multiple Access
Points, it is better if adjacent Access Points use different Channels to reduce inter-
ference.
•
•
In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for
an Access Point. If more than one Access Point can be used, the one with the
strongest signal is used. (This can only happen within an ESS.)
If using "Ad-hoc" mode (no Access Point), all Wireless stations should be set to
use the same Channel. However, most Wireless stations will still scan all Chan-
nels to see if there is an existing "Ad-hoc" group they can join.
WEP
WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmit-
ted.
This is desirable because it is impossible to prevent snoopers from receiving any data
which is transmitted by your Wireless Stations. But if the data is encrypted, then it is
meaningless unless the receiver can decrypt it.
If WEP is used, the Wireless Stations and the Access Point must have the same
settings for each of the following:
Off, 64 Bit, 128 Bit
WEP
Key
For 64 Bit encryption, the Key value must match.
For 128 Bit encryption, the Key value must match
Open System or Shared Key.
WEP Authentication
WPA-PSK
WPA-PSK is another standard for encrypting data before it is transmitted. This is a
later standard than WEP (Wired Equivalent Privacy), and provides greater security for
your data. Data is encrypted using a 256Bit key which is automatically generated and
changed often.
If all your Wireless stations support WPA-PSK, you should use this instead of WEP.
If WPA-PSK is used, the Wireless Stations and the Access Point must have the
same settings for each of the following:
Enter the same value on every station and the AP.
The PSK must be from 8 to 63 characters in length.
The 256Bit key used for the actual encryption is de-
rived from this key.
WPA PSK
(Pre-shared Key)
125
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
The same encryption method must be used. The most
common encryption method is TKIP. Another widely-
supported method is AES.
Encryption
Wireless LAN Configuration
To allow Wireless Stations to use the Access Point, the Wireless Stations and the
Access Point must use the same settings, as follows:
On client Wireless Stations, the mode must be set to "Infrastruc-
ture".
Mode
(The Access Point is always in "Infrastructure" mode.)
Wireless Stations should use the same SSID (ESSID) as the
Access Point they wish to connect to. Alternatively, the SSID
can be set to "any" or null (blank) to allow connection to any
Access Point.
SSID (ESSID)
The Wireless Stations and the Access Point must use the same
settings for Wireless security. (None, WEP, WPA-PSK).
Wireless
Security
WEP: If WEP is used, the Key size (64Bit, 128Bit), Key value,
and Authentication settings must be the same on the Wireless
Stations and the Access Point.
WPA-PSK: If WPA-PSK is used, all Wireless Stations must be
set to use WPA-PSK, and have the same Pre-shared Key and
encryption system.
For Ad-hoc networks (no Access Point), all Wireless stations
must use the same security settings.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
C
About VPNs
Overview
A VPN (Virtual Private Network) provides a secure connection between 2 points, over
an insecure network - typically the Internet. This secure connection is called a VPN
Tunnel.
There are many standards and protocols for VPNs. The standard implemented in the
ADW-4302v2 is IPSec.
IPSec
IPSec is a near-ubiquitous VPN security standard, designed for use with TCP/IP
networks. It works at the packet level, and authenticates and encrypts all packets
traveling over the VPN Tunnel. Thus, it does not matter what applications are used on
your PC. Any application can use the VPN like any other network connection.
IPSec VPNs exchange information through logical connections called SAs (Security
Associations). An SA is simply a definition of the protocols, algorithms and keys used
between the two VPN devices (endpoints).
Each IPSec VPN has two SAs - one in each direction. If IKE (Internet Key Exchange)
is used to generate and exchange keys, there are also SA's for the IKE connection as
well as the IPSec connection.
There are two security modes possible with IPSec:
•
Transport Mode - the payload (data) part of the packet is encapsulated through
encryption but the IP header remains in the clear (unchanged).
The ADW-4302v2 does NOT support Transport Mode.
•
Tunnel Mode - everything is encapsulated, including the original IP header, and a
new IP header is generated. Only the new header in the clear (i.e. not protected).
This system provides enhanced security.
The ADW-4302v2 always uses Tunnel Mode.
IKE
IKE (Internet Key Exchange) is an optional, but widely used, component of IPSec. IKE
provides a method of negotiating and generating the keys and IDs required by IPSec.
If using IKE, only a single key is required to be provided during configuration. Also,
IKE supports using Certificates (provided by CAs - Certification Authorities) to au-
thenticate the identification of the remote user or gateway.
If IKE is NOT used, then all keys and IDs (SPIs) must be entered manually, and
Certificates can NOT be used. This is called a "Manual Key Exchange".
When using IKE, there are 2 phases to creating the VPN tunnel:
•
•
Phase I is the negotiation and establishment up of the IKE connection.
Phase II is the negotiation and establishment up of the IPSec connection.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Because the IKE and IPSec connections are separate, they have different SAs (secu-
rity associations).
Policies
VPN configuration settings are stored in Policies.
Note that different vendors use different terms. Generally, the terms "VPN Policy",
"IPSec Policy", and "IPSec Proposal" have the same meaning. However, some ven-
dors separate IKE Policies (Phase 1 parameters) from IPSec Policies (Phase 2
parameters).
For the ADW-4302v2; each VPN policy contains both Phase 1 and Phase 2 parame-
ters (if IKE is used). Each policy defines:
•
•
•
•
The address of the remote VPN endpoint
The traffic which is allowed to use the VPN connection.
The parameters (settings) for the IPSec SA (Security Association)
If IKE is used, the parameters (settings) for the IKE SA (Security Association)
Generally, you will need at least one (1) VPN Policy for each remote site for which you
wish to establish VPN connections.
It is possible, and sometimes necessary, to have multiple Policies for the same remote
site. However, you should only Enable one (1) policy at a time.
VPN Configuration
The general rule is that each endpoint must have matching Policies, as follows:
Each VPN endpoint must be configured to initiate or accept
connections to the remote VPN client or Gateway.
VPN Endpoint
address
Usually, this requires having a fixed Internet IP address. How-
ever, it is possible for a VPN Gateway to accept incoming
connections from a remote client where the client's IP address
is not known in advance.
This determines which outgoing traffic will cause a VPN connec-
tion to be established, and which incoming traffic will be
accepted. Each endpoint must be configured to pass and ac-
cept the desired traffic from the remote endpoint.
Local & Remote
LAN definition
If connecting 2 LANs, this requires that:
•
Each endpoint must be aware of the IP addresses used on
the other endpoint.
•
The 2 LANs MUST use different IP address ranges.
If using IKE (recommended), the IKE parameters must match
(except for the SA lifetime, which can be different).
IKE parameters
The IPSec parameters at each endpoint must match.
IPSec parame-
ters
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C - VPNs
Common VPN Situations
VPN Pass-through
Figure 96: VPN Pass-through
Here, a PC on the LAN behind the Router/Gateway is using VPN software, but the
Router/Gateway is NOT acting as a VPN endpoint. It is only allowing the VPN connec-
tion.
•
•
The PC software can use any VPN protocol supported by the remote VPN.
The remote VPN Server must support client PCs which are behind a NAT router,
and so have an IP address which is not valid on the Internet.
•
The Router/Gateway requires no VPN configuration, since it is not acting as a
VPN endpoint.
Client PC to VPN Gateway
Figure 97: Client PC to VPN Server
In this situation, the PC must run appropriate VPN client software in order to connect,
via the Internet, to the ADW-4302v2 or other VPN Gateway. Once connected, the
client PC has the same access to LAN resources as PCs on the local LAN (unless
restricted by the network administrator).
•
IPSec is not the only protocol which can be used in this situation, but the ADW-
4302v2 supports IPSec ONLY.
•
Windows 2000 and Windows XP include an IPSec VPN client program. However,
configuration of this client program for use with the ADW-4302v2 is very complex
and beyond the scope of this document.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Connecting 2 LANs via VPN
Figure 98: Connecting 2 VPN Gateways
This allows two (2) LANs to be connected. PCs on each endpoint gain secure access
to the remote LAN.
•
•
The 2 LANs MUST use different IP address ranges.
The VPN Policies at each end determine when a VPN tunnel will be established,
and what systems on the remote LAN can be accessed once the VPN connection
is established.
•
It is possible to have simultaneous VPN connections to many remote sites.
VPN Example
In this example, 2 LANs are connected via VPN. Each end has an ADW-4302v2.
Figure 99: Connecting 2 ADW-4302v2s
Note
•
•
•
The LANs MUST use different IP address ranges.
Both endpoints have fixed WAN (Internet) IP addresses.
This example uses an "Auto" policy, using IKE
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C - VPNs
Configuration Settings - Gateway A
Gateway A should be configured as shown below.
Figure 100: Gateway A Configuration
131
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Configuration Settings - Gateway B
Gateway B should be configured as shown below.
Figure 101: Gateway B Configuration
Settings
Setting
LAN A Gateway
LAN B Gateway
Notes
Policy Name
Example
Example
Name does not affect
operation. Select a
meaningful name.
Remote VPN
Endpoint
Fixed IP Address
205.17.11.43
Fixed IP Address
202.11.13.211
Other endpoint's WAN
(Internet) IP address.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C - VPNs
NetBIOS
Enable
Enable
Disable if not required.
Local LAN
IP address
Mask
192.168.0.1
255.255.255.0
192.168.1.1
255.255.255.0
Local Address subnet.
Use a more restrictive
definition if possible.
Remote LAN
IP address
Mask
192.168.1.1
255.255.255.0
192.168.0.1
255.255.255.0
Remote Address
subnet.
Use a more restrictive
definition if possible.
IKE
Direction
Initiator & re-
sponder
Initiator & re-
sponder
Does not have to
match. Either endpoint
can block 1 direction.
Exchange mode Main Mode
Main Mode
Must match
DH Group
Group 2 (1024
bit)
Group 2 (1024 bit) Must match
Local Identity
IP address
IP address
IP address is the most
common ID method
Remote Identity WAN IP address
WAN IP address
IP address is the most
common ID method
SA Parameters
Encryption
3DES
3DES
Must match.
Must match
Authentication
Pre-shared Key
MD5
MD5
12345678
12345678
Must match;
use any string.
SA Life time
PFS
28800
28800
Does not have to
match. Shorter period
will be used.
Disabled
Disabled
Must match
Note:
Some VPN Gateways or programs let you specify the following settings separately for
IKE and IPSec. For this device, the same settings are used for both IKE and IPSec.
•
•
•
Authentication
Encryption
SA Lifetime
Also, IPSec allows for "AH Authentication", using MD5 or SHA-1. For this device, "AH
Authentication" is always DISABLED.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
D
Specifications
ADSL 2/2+ VPN Firewall Router
Product
Model
802.11g Wireless ADSL 2/2+ VPN Firewall Router
ADW-4302v2A/B
Hardware
Standard
Multi-Mode code support
ANSI T1.413 Issue 2
ITU-T G.994.1 (G.hs) rev. 3
ITU-T G.992.1(G.dmt)
- Annex A (ADSL over POTS for ADW-4302v2A)
- Annex B (ADSL over ISDN for ADW-4302v2B)
ITU-T G.992.2(G.lite)
ITU-T G.992.3 Annex A ADSL2
ITU-T G.992.3 Annex A DELT
ITU-T G.992.3 Annex L READSL2
ITU-T G.992.5 Annex A ADSL2+
RFC 2364 - PPP over ATM (LLC/VCMUX)
RFC 2516 - PPP over Ethernet (LLC/VCMUX)
RFC 1577 - Classic IP over ATM (LLC/VCMUX)
RFC 1483 - Bridged IP over ATM (LLC/VCMUX)
RFC 1483 - Routed IP over ATM (LLC/VCMUX)
Protocol
AAL and ATM Support Integrated ATM AAL5 support
255 VPI plus 65535 VCI address range
Ports LAN
4 (10Base-T/100Base-TX, Auto-Negotiation, Auto MDI/MDI-
X)
Wireless
WAN
LED Indicators
1 x 802.11g wireless access point, antenna detachable
1 (RJ-11, 10/100Base-TX, Auto-Negotiation)
PWR, STATUS, WLAN, ADSL
100 LNK/ACT, 10 LNK ACT for each LAN port
Button
1 for reset/factory reset
Software
Protocol
IP, NAT, ARP, ICMP, DHCP, PPPoE, PPPoA, IPoA, RIP1/2,
SNMPv1
Security
Native NAT firewall, Enhanced policy-based+ SPI firewall,
URL Filter, Blocking log, Virtual Server, DMZ, Access Control
IPSec tunnel
VPN termination
8 simultaneous tunnels (Main Mode)
Throughput 1.5Mbps
DES/3DES encryption
IKE support with pre-shared key
IP address or FQDN identification
MD5, SHA-1 Authentication
PPTP Server (Microsoft VPN) support
Management
Web browser management
Environment Specification
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D - Specifications
Dimension (W x D x H) 175 x 114 x 29 mm
Power
12V DC, 1A
Power Consumption
Temperature:
Humidity
Maximum 9.6W, 32.7 BTU
0~40 degree C (operating), -10~70 degree C (storage)
5%~ 95% (non-condensing)
FCC, CE
Emission
Wireless Interface
Standards
IEEE802.11b, IEEE802.11g WLAN, 802.11G-plus (Texas
Instruments proprietary enhanced mode)
2.4 to 2.4835GHz (Industrial Scientific Medical Band )
Maximum 14 Channels, depending on regulatory authorities
CCK, DQPSK, DBPSK, OFDM/CCK
Frequency
Channels
Modulation
Data Rate
Security
Up to 54 Mbps (802.11g), 64 Mps (TI 802.11G-plus)
WEP 64Bit、128Bit, WPA-PSK, MAC address checking
13dBm (typical)
Output Power
Receiver Sensitivity -80dBm Min.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
ADW-4302v2 User Guide
Regulatory Approvals
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly ap-
proved by the party responsible for compliance could void the user's authority to
operate this equipment. (Example - use only shielded interface cables when connect-
ing to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
CE Approval
CE Standards
This product complies with the 99/5/EEC directives, including the following safety and
EMC standards:
•
•
•
EN300328-2
EN301489-1/-17
EN60950
CE Marking Warning
This is a Class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
|