Digital Camera
Operating Manual
To ensure the best performance from
your camera, please read the Operating
Manual before using the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR SAFE USE OF YOUR CAMERA
Sufficient attention has been paid to the safety of this product but please
pay particular attention to the warnings indicated by the following symbols
during use.
Warning These symbols indicate that it is possible that the
user may experience serious difficulties if the warn-
ings are not heeded.
Caution These symbols indicate that it is possible that the
user may experience minor or middling difficulties or
physical difficulties if the warnings are not heeded.
Warning:
• Do not attempt to take the camera apart or remodel the camera. High voltages are
present within the camera, and there is therefore a danger of electric shocks.
• If the inside of the camera should become exposed as a result of, for example, the
camera being dropped, please do not under any circumstances touch such exposed
portions, as there is a danger of receiving an electric shock.
• Wrapping the strap of the camera around your neck is also dangerous, and please
take care that small children do not hang the strap around their necks.
• Use an AC adapter that are of the power and voltage specified for exclusive use with
this product. The use of an AC adapter other than that specified exclusively for use
with this product may cause fire or electric shocks.
• If the camera emits smoke or a strange smell, or in the event of any other irregularity,
stop using the camera immediately, remove the battery or disconnect the AC adapter
and contact your nearest Pentax service center. Continued use of the camera may
result in fire or electric shock.
• Discontinue use of the AC adapter during thunderstorms. This can cause a fire or
electrical shock.
Caution:
• Never try to disassemble, short or recharge the battery. Also, do not dispose of the
battery in fire, as it may explode.
• Remove the battery from the camera immediately if it becomes hot or begin to
smoke.
Be careful not to burn yourself during removal.
• Some portions of the camera heat up during use, so please take care, as there is a
risk of low temperature burns if such portions are held for long periods of time.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Care to be Taken During Handling
• Do not clean the product with organic solvents such as thinner or alcohol benzene.
• Places of high temperature and humidity should be avoided. Particular care should
be taken regarding vehicles, which can become very hot inside.
• Storing the camera where pesticides and chemicals are handled should be avoided.
Remove from case and store in a well-ventilated place to prevent the camera from
becoming moldy during storage.
• Do not use the camera where it may come in contact with rain, water or any other liq-
uid, because the camera is not weather, water, or liquid resistant. Should the camera
get wet from rain, splashing water, or any other liquid, wipe it off immediately with a
dry soft cloth.
• Ensure that the camera is not subjected to substantial vibrations, shocks or pressure.
Place the camera on a cushion for protection when the camera is subjected to the
vibrations of a motorbike, car, or ship, etc.
• The liquid crystal display will become black at temperatures of approximately 60°C
but will return to normal when normal temperatures are returned to.
• The display response speed of the liquid crystal becomes slow at low temperatures
but this is due to the properties of the liquid crystal and is not a fault.
• Remove dust from the lens and viewfinder using a blower or clean off dust using a
lens brush.
• Periodic checks are recommended every 1 to 2 years in order to maintain high-perfor-
mance.
• When the camera has not been used for a long time, please, without fail, try out the
camera to confirm that it is still working properly, particularly prior to taking important
pictures (such as at a wedding or during travelling). No guarantee can be given with
regards to collateral damage (costs incurred as a result of taking pictures, loss of
benefits that were to be obtained through taking pictures) that may cause this product
to fail.
• If the camera is subjected to rapid temperature changes, drops of water appear on
the inside and outside of the camera. Therefore put the camera in a bag or plastic
bag, and take the camera out when the difference in temperature has subsided.
• The temperature range in which the camera can be used is 0°C to 40°C.
• Take care to ensure that garbage, dirt, sand, dust, water, toxic gases, salt, etc. do not
enter within the camera, as this may cause the camera to become damaged. If rain
or drops of water get onto the camera, please wipe dry.
• Please refer to “Precautions When Using a CF Card” (p.14) regarding the
CompactFlash CF card.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
FOR SAFE USE OF YOUR CAMERA······························································1
Care to be Taken During Handling ···································································2
Contents ···········································································································3
Contents of the Operating Manual ···································································5
Checking the Contents of the Package ····························································6
Names of Parts·································································································7
Names of Operating Parts················································································8
Getting Started··············································································9
Attaching the Strap···························································································9
Powering the Camera·····················································································10
Installing the Battery··············································································10
Using the AC Adapter (optional) ···························································12
Installing or removing the CF Card·································································13
Initial Settings ·································································································15
Setting the Display Language ·······························································15
Setting the Home Town ·········································································16
Setting the D.S.T Mode ·········································································16
Setting the Video Output Format···························································17
Setting the Date and Time ····································································17
Quick Start···················································································20
Taking Still Pictures ························································································20
Playing Back Still Pictures··············································································22
Playing Back the Last Image Taken (Easy View) ··································22
Playing Back a Single Image ································································23
How to use the CF Card·················································································24
Common Operations ··································································26
Turning the Camera On and Off·····································································26
Changing the Mode ························································································27
Using the Button Functions ············································································28
Capture Mode························································································28
Playback Mode······················································································29
Using the Menus·····························································································30
How to Use the Menus··········································································30
Menu List·······························································································32
Taking Pictures ···········································································34
Displaying Shooting Information (Display Mode)············································34
Taking Pictures ·······························································································35
Taking Still Pictures in Auto Mode (Auto Mode)····································35
Taking Pictures with All the Functions Set (Full Selectable Mode)·······36
Taking Dark Scenes (Night-Scene Mode)·············································37
Continuous Shooting·············································································38
Using the Self-Timer··············································································39
Taking Movie Pictures (Movie Picture Mode)········································40
Using the Zoom·····················································································42
Taking a Picture of Yourself (Self-Portrait Mode)···································44
Taking Stereo Pictures (3D image mode) ·············································45
Automatically Changing the Shooting Conditions (Auto bracket)··········50
Setting the Shooting Functions ······································································52
Selecting a Focus Mode········································································52
EV Compensation ·················································································54
Selecting the Flash Mode······································································55
Selecting the Recorded Pixels ······························································56
Selecting the Quality Levels··································································57
Adjusting the Color Balance according to Lighting (White Balance)·····58
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the AF Area (Focusing Area)················································60
Setting the Light Metering Range to Determine the Exposure (AE Metering)··61
Setting the ISO Speed (ISO Speed) ·····················································62
Selecting the Color Mode (Color)··························································63
Setting the Instant Review Time (Instant Review)·································64
Setting the Sharpness (Sharpness)······················································65
Setting the Saturation (Saturation)························································66
Setting the Contrast (Contrast) ·····························································67
Saving the Settings (Memory)········································································68
Saving the Menu Items (Mode Memory)···············································68
Saving the Exposure Compensation Setting·········································69
Playback/Erasing ········································································70
Playing Back Images on the Camera·····························································70
Playing Back Still Pictures·····································································70
Zoom Display·························································································70
Playing Back Movie Pictures·································································71
Displaying Shooting Information (Display mode) ··································72
Nine-image Display ···············································································73
Slideshow ······························································································74
Erasing Images·······························································································75
Erasing a Single Image·········································································75
Erasing All Images ················································································76
Protecting Images from Deletion (Protect)············································77
Viewing Images on a TV·················································································78
Setting the Printing Service············································································79
Printing Single Image············································································79
Printing All Images ················································································81
Viewing images with Windows PC ·································································82
About the included software··································································82
System environment··············································································82
Installing the software············································································83
Connecting the camera and PC····························································93
Viewing images on your PC··································································94
Disconnecting the camera from your PC ··············································95
Viewing Images with Macintosh ·····································································98
About the included software··································································98
System environment··············································································98
Installing the software············································································99
Connecting the camera and your Macintosh·······································100
Viewing images on your Macintosh·····················································101
Disconnecting the camera from your Macintosh·································101
Settings······················································································102
Camera Settings···························································································102
Formatting a CF Card ·········································································102
Setting the Date Style ·········································································103
Changing the Date/Time ·····································································104
Changing the Display Language ·························································104
Changing the Video Output Format·····················································105
Setting the Beep··················································································105
Setting the World Time········································································106
Powersaving Function (Sleep Timeout)···············································108
Auto Power Off Function ·····································································108
Setting the Brightness Level································································109
Resetting to Default Settings (Reset)··················································109
Appendix····················································································110
List of City Names ························································································110
Messages ·····································································································111
Troubleshooting ····························································································113
Main Specifications·······················································································116
4
Download fromWWARwRwAN.SToYmPOaLnICuYa·l·s··.··c··o···m····.···A···l·l···M····a··n···u···a···l·s···S····e··a···r··c··h····A····n··d····D····o···w···n··1lo18ad.
Contents of the Operating Manual
This Operating manual contains the following chapters.
● Getting Started
This chapter explains what you need to do after purchasing the camera
before you start taking pictures. Be sure to read it and follow the instructions.
● Quick Start
This chapter explains the simplest way to take pictures and play back images.
Use it if you want to start taking pictures straightaway. It also tells you how to
use the CF card.
● Common Operations
This chapter explains common operations such as the functions of the mode
dial and buttons, and how to use the menus. For more details, refer to the
respective [Taking Pictures], [Playback/Erasing] and [Settings] chapters.
● Taking Pictures
This chapter explains the various ways of capturing images and
how to set the relevant functions.
● Playback/Erasing
This chapter explains how to play back images on the camera or
on a TV and how to delete images.
● Settings
This chapter explains how to set the camera-related functions.
● Appendix
This tells you about the messages displayed on the LCD monitor
and what to do in the event of trouble.
The meanings of the symbols used in this Operating manual are
explained below.
indicates the reference page number for an explanation of the
related operation.
memo
indicates information that is useful to know.
Caution
indicates precautions to be taken when operating the camera.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Contents of the Package
Camera
Optio 230
Strap
O-ST5
Software (CD-ROM)
S-SW5
Video cable I-VC2
USB cable I-USB2
3D Image Viewer
O-3DV1
Digital Camera
Operating Manual
To ensure the best performance from
your camera, please read the Operating
Manual before using the camera.
Lithium battery
CR-V3
Operating Manual
this manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Parts
Front
Shutter release button
Power switch
Viewfinder
Self-timer lamp/AF spot-
beam
Built-in flash
USB/Video output terminal
DC input terminal
Terminal cover
Lens
Back
Viewfinder
LCD monitor
Strap lug
CF card cover
Battery chamber cover
Tripod socket
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Operating Parts
/
button
/
/
button
/
/
Power switch
Shutter release button
Mode dial
Zoom button
Menu button
OK button
Four-way controller
(
)
Display button
Status lamp
Flash lamp
Reverse button
● Guide indications
A guide to available button operation is displayed on the LCD monitor during
operation. The buttons are indicated as shown below.
Four-way controller (
)
Zoom button
(Only for digital zoom
and magnified playback)
Four-way controller (
Four-way controller (
Four-way controller (
Menu button
)
)
)
Display button
button
button
MENU
OK
Shutter release button
Reverse button
OK button
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Attaching the Strap
Pass the narrow end of the strap through the strap lug and pass
the other end through the loop.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering the Camera
Inserting the Battery
Insert the battery into the camera. When using the camera for the
first time, insert a new battery.
z Slide the battery chamber cover sideways and lift it up.
x Insert the battery in the direction indicated by the (+) (–)
marks inside the battery chamber.
c Close the battery chamber cover and slide it back into
place.
•
If you intend to use the camera for a long period, use of the AC
adapter D-AC5 (optional) is recommended. ( p.12)
memo
• Do not open the battery chamber cover or remove the bat-
tery when the camera is turned on.
Caution
• If you do not intend to use the camera for a long time,
remove the battery.
• If the camera is left without the battery for a long time, the
date setting will be reset.
• Insert the battery correctly. If the battery is incorrectly ori-
ented, it may cause a malfunction.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
● Approximate Operating Time (when new batteries are
loaded)
Number of recordable images
LCD monitor LCD monitor Playback time
ON
OFF
With the
flash fired
for 50% of
the shots
Without
CR-V3 lithium
AA lithium
AA NiMH
AA alkaline
CR-V3 lithium
AA lithium
AA NiMH
500
400
200
100
600
450
250
150
650
450
250
200
850
650
300
300
—
—
—
—
240
180
100
30
the flash
AA alkaline
* The above table is based on Pentax measuring conditions and may vary
depending on capture mode and shooting conditions.
Performance of the battery may deteriorate in low tempera-
tures.
Caution
●
Battery Level Indicator
You can check the battery level by the
the LCD monitor.
symbol displayed on
(lit green) : Adequate power remains.
(lit yellow) : Battery remains half.
(lit red) : Battery is exhausted.
↓
↓
↓
[Battery depleted] : After the message is displayed, the camera
will turn off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AC outlet
Using the AC Adapter (optional)
If you intend to use the LCD monitor for a long time or connect the
camera to a PC, use of the AC adapter D-AC5 (optional) is recom-
mended.
z Make sure that the camera is turned off before opening
the terminal cover.
x Connect the DC terminal on the AC adapter to the DC
input terminal on the camera.
c Connect the AC plug cord to the AC adapter.
v Plug the AC plug cord into the power outlet.
When using the AC adapter, the battery level indicator is not dis-
played on the LCD monitor.
memo
• Make sure that the camera is turned off before connecting
or disconnecting the AC adapter.
Caution
• Make sure that the AC plug cord and connecting cord are
inserted securely. If the cord becomes disconnected while
you are taking pictures, the data may be lost.
• When using the AC adapter D-AC5, be sure to read the
operation manual accompanying the AC adapter.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or removing the CF Card
Captured images are recorded on the CompactFlash (CF) card.
Make sure that the camera is turned off before inserting or remov-
ing the CF card (optional).
Installing the Card
z Open the CF card cover.
x Orient the card with the surface of the card having the
symbol facing towards the lens and with the
pin-connector edge of the card towards the slot and
insert fully.
c Close the CF card cover.
Removing the Card
z Open the CF card cover.
x Press the CF card eject button and remove the card.
c Close the CF card cover.
• If you open the CF card cover when the camera is turned
on, a warning beep will sound and the camera will be
forcibly turned off.
Caution
• If you open the CF card cover while recording an image on
the CF card, the recording operation will be terminated (the
image will not be saved).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
● Approximate Number of Recordable Images and Recorded
pixels/Quality levels
Quality levels
Recorded pixels
TIFF
Best
—
Better
—
Good
Movie images
(
)
(
)
(
)
1600 × 1210
2
—
—
—
—
—
2
1600 × 1200
1024 × 768
640 × 480
320 × 240
—
—
—
—
Approx. 14 Approx. 29 Approx. 64
Approx. 26 Approx. 53 Approx. 94
Approx. 53 Approx. 94 Approx. 133
—
—
—
•
•
The above table indicates is the number of images when using a 16MB CF
card.
The above table is based on standard shooting conditions specified by
PENTAX and may vary depending on the subject, shooting conditions, cap-
ture mode, CF card, etc.
Precautions When Using a CF Card
•
•
Make sure that the camera is turned off before opening the CF card cover.
Care should be taken if you remove the CF card immediately after using the
camera, as the card may be hot.
•
Do not open the CF card cover or turn the camera off while data is being
recorded on the card or transferred to another device as this may cause the
data to be lost or the card to be damaged.
•
•
•
•
Do not bend the CF card or subject it to violent impact. Keep it away from water
and store away from high temperature.
Be sure to format unused CF cards or CF cards that have been used on another
camera. Refer to “Formatting a CF Card” (p.102) for instructions on formatting.
Never open the CF card cover during formatting as this may cause the card to
be damaged and become unusable.
Data recorded on a CF card with the Optio 230 cannot be played back accu-
rately on the Optio 330 or Optio 430. Similarly, data recorded with the Optio 330
or Optio 430 cannot be played back accurately on the Optio 230.
The data on the CF card may be erased in the following circumstances. Pentax
does not accept any liability for data that is erased
•
•
•
•
•
when the CF card is mishandled by the user.
when the CF card is exposed to static electricity or electrical interference.
when the card has not been used for a long time.
when the card is ejected, the AC adapter is disconnected or the battery is
removed while the data on the card is being accessed (when the status lamp
and flash lamp are blinking green and red).
•
The CF card has a limited service life. If it is not used for a long time, the data
on the card may become unreadable. Be sure to make a backup of important
data on a PC.
•
•
Avoid using or storing the card where it may be exposed to static electricity or
electrical interference.
Avoid using or storing the card in direct sunlight or where it may be exposed to
rapid changes in temperature or to condensation.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Settings
Power switch
Menu button
Four-way controller
OK button
Display button
If the initial settings screen appears when you turn the camera on,
follow the procedure below to set the display language, Home
Town, DST, video output format and current date and time. If the
date and time appear at the bottom right of the LCD monitor when
you turn the camera on for the first time, follow the instructions for
“Changing the Date/Time” (p.104) to set the correct date and time.
Setting the Display Language
You can choose the language in which the menus, error mes-
sages, etc. are displayed.
z Turn the camera on.
Initial setting
x Use the four-way controller (
Language/
English
NYC
) to select the display lan-
guage.
The default setting is English.
NTSC
OK
MENU
c Press the four-way controller
(
).
The screen for setting the next item will be displayed.
You can change the setting after it has been made. Refer to
“Changing the Display Language” (p.104).
memo
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Home Town
You can choose the city (Home Town) in
which you will use the camera.
Initial setting
Language/
English
NYC
z Press the four-way controller (
) to select the desired city
(Home Town).
NTSC
OK
MENU
x Press the four-way controller ( ).
The screen for setting the next item will be displayed.
•
•
See p.110 for the list of cities and corresponding code names.
You can change the setting after it has been made. Refer to
“Setting the World Time” (p.106).
memo
Setting the D.S.T. Mode
You can choose whether or not to display the D.S.T mode.
z Use the four-way controller (
)
Initial setting
Language/
to select
(On) or
(Off).
English
NYC
The default setting is
(Off).
x Press the four-way controller ( ).
The screen for setting the next item
will be displayed.
NTSC
OK
MENU
You can change the setting after it has been made. Refer to
“Setting the World Time” (p.106).
memo
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Video Output Format
You can choose the output format (NTSC
or PAL) for taking or playing back pictures
using a TV monitor.
Initial setting
Language/
English
NYC
NTSC
OK
z Use the four-way controller (
to select the video output format.
The default setting is NTSC.
)
MENU
x Press the OK button.
The screen for setting the date and time will be displayed.
•
You can change the setting after it has been made. Refer to
“Changing the Video Output Format” (p.105).
memo
Setting the Date and Time
Set the current date and time.
z Use the four-way controller (
)
Date Adjust
01 / 01 / 2002
00 : 00
DISP 12H/24H
MENU OK
to change the month.
Date Adjust
x Press the four-way controller ( ).
and
will be displayed
04 / 01 / 2002
00 : 00
above and below the day.
DISP 12H/24H
MENU OK
17
Download from Www.Somanuals.com. All Manuals Search And Download.
c Use the four-way controller (
to change the day and press the
four-way controller ( ).
)
Date Adjust
04 / 23 / 2002
00 : 00
DISP 12H/24H
MENU OK
and
will be
displayed above and below the year.
v Repeat Step c to change the
Date Adjust
[year] [hour] and [minutes].
04 / 23 / 2002
00 : 00
DISP 12H/24H
MENU OK
b Use the Display button to select the
Date Adjust
12-hour or 24-hour display format.
04 / 23 / 2002
11 : 00 PM
n When you have finished the set-
tings, press the OK button when
the clock reaches 00 seconds.
The screen confirming the settings
will be displayed and the camera is
ready to take a picture.
DISP 12H/24H
MENU
OK
•
•
You can cancel setting operation and switch to Capture mode
memo
by pressing the MENU button. In this case, the initial settings
screen will be displayed next time you turn the camera on.
You can change the settings after they have been made. Refer
to “Changing the Date/Time” (p.104).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Taking Still Pictures
Zoom button
Power switch
Viewfinder
LCD monitor
Shutter
release button
Display button
Mode dial
Power switch
For the simplest procedure to take still pictures:
The flash fires automatically depending on the light conditions.
z Press the power switch.
200
The camera will turn on.
x Set the mode dial to
.
c Turn the LCD monitor on.
Press the Display button to dis-
play the shooting screen on the
LCD monitor.
1/250
F2.8
04/23/2002
11:19
Focus frame
The focus frame in the middle of
the LCD monitor indicates the
zone of automatic focusing. You
can change the size of the sub-
ject by pressing the Zoom but-
ton.
makes the subject bigger.
makes the subject smaller.
Viewfinder
You can check the size of the subject by looking through
the viewfinder.
As there is no focus frame in the viewfinder, be sure to check
the focusing area on the LCD monitor.
memo
20
Download from Www.Somanuals.com. All Manuals Search And Download.
v Press the shutter release button.
The image will be displayed on the LCD monitor for 0.5
seconds (Instant Review) and recorded on the CF card.
(The green and red lamps on the right of the viewfinder
blink alternately while the image is being recorded on the
CF card.)
Using the Shutter Release Button
The shutter release button works in a two-step action.
● Press halfway
When the shutter release button is pressed lightly (halfway),
the focus, exposure and white balance are locked. You can
find the following information on the LCD monitor, the status
lamp and the flash lamp.
The shutter speed and aperture settings are only displayed
when the shutter release button is pressed lightly (halfway).
q Focusing area
If the subject is in focus, the frame will light green. If the
subject is not in focus, the frame will not appear.
w Flash symbol
The flash symbol indicates the status of the flash when the
shutter release button is pressed.
Status lamp & Flash lamp (on the right of the viewfinder)
status Status lamp (green)
Flash lamp (red)
Flash is charged
Flash is charging
lit
Subject is in focus
blink
Subject is not in focus
● Pressed down fully
The picture is taken.
Instant Review
The Instant Review default setting is 0.5 seconds. During this
time you can delete the image by pressing the button (The
[Delete] menu will be displayed.), and selecting [Delete].
Setting the Instant Review Time p.64
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Playing Back Still Pictures
LCD monitor
OK button
Playing Back the Last Image Taken (Easy View)
You can display the last still picture taken.
z Press the OK button after tak-
ing a picture.
The last image taken will be dis-
played on the LCD monitor.
During this time you can erase
Delete
the image by pressing the
button (The [Delete] menu will
be displayed.), and selecting
[Delete].
Press the OK button again to
return to shooting status.
•
You can enlarge the image displayed on the LCD monitor by
pressing the zoom lever.
memo
Playing Back Still Pictures
p.70
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD monitor
Four-way controller
Mode dial
Playing Back a Single Image
You can play back still pictures one at a time.
z Set the mode dial to
.
An image will be displayed on the LCD monitor.
x Press the four-way controller (
).
displays the previous image.
displays the next image.
•
•
In the case of movie pictures, the first frame will be displayed.
If there are no image stored on the CF card, the [No images
in camera] message will be displayed, and if there is no CF
card in the camera, the [No card in camera] message will
be displayed.
memo
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
How to Use the CF Card
Images taken with the Optio 230
camera are recorded on the CF card.
You can view the images recorded
on the card on the camera itself,
transfer them to your PC and print
them out.
Viewing images on the camera
One of the advantages of a digital
camera is that it enables you to view
your pictures immediately after you
have taken them. You can check the
composition and brightness and take
the picture again if you are not satis-
fied.
Playing Back Still Pictures
p.22
Viewing images on a TV
If you want to show your pictures to friends, you can display
them on your TV monitor. To view images on your TV, connect
the camera to the TV with the video cable.
Viewing Images on a TV
p.78
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing images on a PC
You only need to install the USB driver the first time. After that,
you can view recorded images and edit them on the PC just by
connecting the camera to the PC with the USB cable and
downloading the images. Or you can remove the CF card from
the camera and transfer the data to your PC using a card
reader. If you use a laptop computer, you can transfer the
image data by fitting the CF card into the card adapter and
inserting the card adapter into the card slot.
Viewing Images with Windows PC
Viewing Images with Macintosh
p.82
p.98
Printing images by a printing service
By selecting the pictures you want to have printed and specify-
ing the number of prints in advance on the CF card, you can
take the card to a DPOF-compatible (Digital Print Order
Format) printing service and have prints made.
Setting the Printing Service
p.79
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Operations
Turning the Camera On and Off
z
Use the power switch to turn the camera on and off.
z Press the power switch.
The camera will turn on.
When the camera is turned on, the lens cover opens and the
lens extends.
Press the power switch again to turn the camera off.
If you turn the camera on in Playback mode, the lens cover
remains closed and the lens does not extend.
memo
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Mode
Capture mode is for taking pictures and Playback mode is for play-
ing back or erasing images. The mode is set by the mode dial.
Capture Mode
Auto mode
Most of the settings are made
automatically by the camera when
a picture is taken.
p.35
Full selectable
mode
You can set all the functions as
you like when a picture is taken.
p.37
p.36
p.40
Night-scene mode
This mode is for taking dark
scenes such as night views.
Movie picture mode
This mode is for taking moving
images.
Playback Mode
This mode is for playing back
recorded images.
Playback mode
p.70
z Turn the mode dial so that the mark is on
or
.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Button Functions
q
w
e
r
t y
i
u
Capture Mode
q
button
Changes the flash mode. (
p.55)
w
button
Changes the shooting mode as follows.
Using the Self-timer (
Using macro mode (
Infinity landscape mode (
p.39)
p.52)
p.52)
Manual focus (
eZoom button
Changes the size of the subject. (
p.53)
p.42)
rMenu button
Displays the active menus in Capture mode. (
tFour-way controller (
Changes the EV compensation in
p.32)
p.54)
)
mode. (
yFour-way controller (
Adjusts the focus in
uDisplay button
)
mode. (
p.52)
Changes the information displayed on the LCD monitor. (
p.34)
iReverse button
Reverse the image from right to left. (The image is not recorded
in reverse.
p.44)
MF (manual focus) and EV compensation are disabled in Auto
mode .( p.35)
memo
28
Download from Www.Somanuals.com. All Manuals Search And Download.
q
w
e
r
t
y
u
Playback Mode
q
button
Erases the image. (
p.75)
w
button
Protects the image from erasure. (
eZoom button
Changes the size of the image displayed on the LCD monitor.
p.70)
p.77)
(
rMenu button
Displays the active menus in Play mode. (
p.33)
tFour-way controller (
)
Displays images one by one. (
yOK button
Displays nine images at once. (
uDisplay button
p.23)
p.73)
Changes the information displayed on the LCD monitor. (
p.72)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
When you press the Menu button, the menu is displayed on the LCD moni-
tor. You can set the shooting functions in Capture mode (
the playback functions in Playback mode ( ).
) or
You can set the camera functions in both Capture mode and Playback
mode.
How to Use the Menus
When you are making settings from a menu, a guide to operation
is displayed on the LCD monitor.
z Press the Menu button.
The menu screen will be displayed. The selected area will be
displayed in a green frame.
x Press the four-way controller (
Use the four-way controller (
screen.
).
) to select the menu
c Use the four-way controller (
Use the four-way controller (
down.
) to select an item.
) to move the frame up or
v Use the four-way controller (
) to change the setting.
v’ If there is a Select screen, use the four-way controller
) to move to the Select screen.
(
When you have finished making the settings, press the OK
button to return to the menu.
b Press the OK button.
The settings will be saved and the screen will return to shoot-
ing or playback status.
• If you press the Menu button and leave the menu screen,
any changes to setting will not be saved.
Caution
• Even if you press the OK button and leave the menu
screen, if you remove the battery before turning off the
camera or do not otherwise turn off the camera correctly,
any changes to setting will not be saved.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of shooting (in Capture mode)
z Menu button
[Rec.Mode] menu
[Applied Function] menu
[Set-up] menu
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Rec.Mode
Applied Function
Set-up
Rec.Mode
Applied Function
Set-up
Resolution
3D image mode
Auto bracket
Format
Quality Level
White Balance
Focusing Area
Digital Zoom
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
MENU
OK
MENU
OK
MENU
x
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
MENU
OK
c
v
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Rec.Mode
Applied Function
Set-up
Resolution
Resolution
1600×1200
Quality Level
White Balance
Focusing Area
Digital Zoom
Quality Level
White Balance
Focusing Area
Digital Zoom
AWB
MENU
OK
MENU
OK
(Ex.) Turning the digital zoom off
c
v’
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
White Balance
AWB
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
MENU
OK
MENU
OK
(Ex.) Adjusting the white balance
c
To the next screen
When you press the Menu button in Playback mode, the Playback
mode menu will be displayed.
memo
Press the four-way controller (
) to switch to the [Playback] or
31
[Set-up] menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu List
Active Menus in Capture Mode
● [Rec.Mode] Menu
Item
Description
Default Setting Reference
Auto mode
Adjustable
For selecting the size of
recorded pixels.
Resolution
1600 × 1200 p.56
For selecting the image
compression rate.
Quality Level
White Balance
Focusing Area
p.57
Adjustable
For adjusting the color bal-
ance according to lighting.
AWD (Auto) p.58 Fixed at default setting
For changing the Area of
the autofocus.
[
](Wide) p.60 Fixed at default setting
For taking digital zoom pictures.
Digital Zoom
AE Metering
(On)
p.43 Fixed at default setting
p.61 Fixed at default setting
For setting the metering method
to determine the exposure.
For setting the ISO speed.
For selecting the color mode.
For setting the instant review time.
ISO Speed
Color
Auto
Full
p.62 Fixed at default setting
p.63 Fixed at default setting
p.64 Fixed at default setting
p.68 Fixed at default setting
Instant Review
Memory
0.5sec
For saving the shooting function set-
tings when the camera is turned off.
(Off)
For saving the exposure
compensation setting when
the camera is turned on.
Exp.
comp.
memory
p.69 Fixed at default setting
p.38 Fixed at default setting
(Off)
For taking pictures continuously while
the shutter release button is pressed.
Continuous
Shooting
For setting the sharpness.
For setting the saturation.
For setting the contrast.
Sharpness
Saturation
Contrast
Normal
p.65 Fixed at default setting
p.66 Fixed at default setting
p.67 Fixed at default setting
Normal
Normal
● [Applied Function] Menu
Item
Description
Default Setting Reference
Parallel method p.45
Auto mode
For taking 3-D pictures.
3D image mode
Auto bracket
–
–
For setting the shooting con-
ditions such as exposure, sat-
uration and sharpness.
Exposure
p.50
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Active Menus in Playback Mode
● [Playback] Menu
Item
Description
Default setting Reference
Slideshow
Recorded images are played
successively.
3s (3 sec.
intervals)
p.74
DPOF
For setting the printing service.
–
p.79
Active Menus in Capture/Playback Mode
● [Set-up] Menu
Item
Description
Default Setting Reference
Auto mode
Adjustable
Adjustable
Format Card For formatting the CF card Cancel
p.102
Date Style
For setting the date style Set according p.103
to the
Language
default setting
Date Adjust For adjusting the date and time 01/01/2002 p.104
Adjustable
World Time For setting the world time
(Off)
On
p.106
p.105
Adjustable
Adjustable
Beep
For adjusting the beep sound
when a button is pressed
English
Language
For changing the language
in which menus and mes-
sages are displayed
p.104
p.105
Adjustable
Adjustable
Set according to
the Language
default setting
Video Out
For setting the video out-
put format
1min.
Sleep
Timeout
For setting the power-
saving function
p.108
p.109
p.109
Adjustable
Adjustable
Adjustable
Normal
Brightness
Level
For setting the brightness
of the LCD monitor
Reset
For returning the camera
settings to defaults
Cancel
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking Pictures
Displaying Shooting Information (Display Mode)
Display On
123 45
6
Shooting information is displayed.
q Flash mode w Focus mode/
Self-timer e Continuous Shooting
mode On r Applications
198
t AF frame y Remaining images
u Shutter speed & aperture
1/250
F2.8
04/23/2002
11:19
i Battery symbol o Date & time
7
8
9
Display Off
No shooting information is displayed.
•
•
•
Only the AF frame is displayed in auto
focus mode.
If there is any change in the battery
level, the battery symbol is displayed.
If there is any change in such as Flash
mode, the mode you have changed is
displayed for a few seconds.
LCD Monitor Off
The LCD monitor is turned off.
Saving the Display Mode
p.68
Display On
When using the AC adapter, the battery level indicator is not dis-
played on the LCD monitor.
memo
LCD Monitor Off cannot be set in Movie Picture mode.
Caution
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking Pictures
z
x
Taking Still Pictures in Auto Mode (Auto Mode)
By setting the mode dial to
, most of the settings will be made
automatically by the camera when a picture is taken.
z Set the mode dial to
.
x Press the shutter release button.
The picture will be taken.
In Auto mode, with the exception of certain functions, the menu
settings are fixed at the default settings. See “Menu List” (p.32) for
the menus where the settings can be changed.
memo
Using the Shutter Release Button
p.21
35
Download from Www.Somanuals.com. All Manuals Search And Download.
x
z
c
Taking Pictures with All the Functions Set (Full Selectable Mode)
By setting the mode dial to
, you can set all of the functions.
z Set the mode dial to
.
x Press the Menu button.
The Menu screen will be displayed. For details of how to
make the settings, see “How to Use the Menus” (p.30).
c Press the shutter release button.
The picture will be taken.
Using the Shutter Release Button
Playing Back Images p.22
p.21
36
Download from Www.Somanuals.com. All Manuals Search And Download.
z
x
Taking Dark Scenes (Night-Scene Mode)
The appropriate settings are made automatically for taking dark
scenes such as night views.
z Set the mode dial to
.
x Press the shutter release button.
The picture will be taken.
Using the Shutter Release Button
p.21
Playing Back Images
p.22
As the shutter speed becomes slow in night-scene mode,
camera shake should be avoided.
Caution
37
Download from Www.Somanuals.com. All Manuals Search And Download.
z (
)
n
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
x Menu button
Resolution
c v Four-way controller
Quality Level
White Balance
Focusing Area
Digital Zoom
MENU
MENU
OK
b OK button
Continuous Shooting
Pictures are taken continuously while the shutter release button is
pressed.
Rec.Mode
Applied Function
Set-up
z Set the mode dial to
.
Exp.comp.memory
Continuous shooting
Sharpness
Saturation
Contrast
x Press the Menu button.
The [Rec. Mode] menu will be dis-
played.
MENU
OK
c Press the four-way controller (
)
to select [Continuous Shooting].
v Press the four-way controller ( ) to select
(On).
b Press the OK button.
The
(Continuous Shooting) icon will be displayed on the
LCD monitor.
n Press the shutter release button.
Pictures will be taken continuously while the shutter release
button is pressed, and stop when the button is released.
Playing Back Images
p.22
•
•
You can continue shooting until the CF card is full.
The interval will vary according to the [Resolution] and [Quality
Level] setting.
memo
• The flash will not fire in Continuous Shooting mode.
• Continuous shooting is not possible in Auto and Movie pic-
ture mode.
Caution
38
Download from Www.Somanuals.com. All Manuals Search And Download.
x
c
z (
)
Using the Self-Timer
The picture is taken ten seconds after the shutter release button is
pressed.
z Set the mode dial to
or
.
x Press the
button to display
on the LCD
/
/
/
monitor.
c Press the shutter release button.
The self-timer is engaged and the self-timer lamp lights. The
picture is taken approximately three seconds after the self-
timer lamp starts to blink.
If you turn the LCD monitor on, the second count will be dis-
played.
memo
Playing Back Images
p.22
Taking picture with self-portrait Mode
p.44
39
Download from Www.Somanuals.com. All Manuals Search And Download.
z
x c
Taking Movie Pictures (Movie Picture Mode)
This mode enables you to take moving images. The maximum
length of one motion picture is 30 seconds.
z Set the mode dial to
.
1
2 3
The following information will be dis-
played on the LCD monitor.
q Flash Off
5
•12SEC
w Remaining shooting time
e Remaining number of sets
04/23/2002
11:19
x Press the shutter release button.
Shooting will start.
You can change the size of the image using the Zoom button.
makes the image bigger
makes the image smaller
c Press the shutter release button.
Shooting will end.
The remaining shooting time will be displayed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Keeping the shutter release button pressed
If you keep the shutter release button pressed for more than one
second, pictures will be taken for as long as you keep the button
pressed. Shooting stops when the button is released.
Playing Back Movie Pictures
p.71
• The flash will not fire in Movie Picture mode.
• Continuous shooting is not possible in Movie Picture mode.
• The LCD monitor cannot be turned off in Movie Picture
mode.
Caution
• Sound cannot be recorded in Movie Picture mode.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Using the Zoom
You can use the zoom to take pictures in Tele or Wide mode.
z Press the Zoom button in Capture
198
mode.
makes the subject larger
makes the subject smaller
When the digital zoom function is
disabled, you can take pictures at
up to 3x magnification using the
optical zoom.
Zoom bar Digital
zoom range
When the digital zoom is enabled,
you can further enlarge the subject
to a maximum magnification equiva-
lent to 7.5x.
198
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Enabling the Digital Zoom Function
z Press the Menu button in Capture
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
mode.
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
The [Rec.Mode] menu will be dis-
played.
x Press the four-way controller (
)
MENU
OK
to select [Digital Zoom].
c Use the four-way controller ( ) to select
(On).
v Press the OK button.
The camera is ready to take a picture.
• When you turn the LCD monitor off, the digital zoom is dis-
abled even if the digital zoom function is set to On.
• The digital zoom function is disabled when the Record
mode is set to TIFF.
Caution
Saving the Digital Zoom Function Setting
p.68
43
Download from Www.Somanuals.com. All Manuals Search And Download.
c
x
z
Taking a Picture of Yourself (Self-Portrait Mode)
You can turn the LCD monitor over, enabling you to see yourself in
the monitor when you want to take a picture of yourself or include
yourself in the picture.
z Turn the LCD monitor over.
x Reverse the image on the LCD monitor.
When you press the Reverse button,
appears on the LCD
monitor and the image is displayed in reverse from right to
left.
c Press the shutter release button.
The picture is taken.
•
•
•
The image is not recorded in reverse.
The menu screen is not reversed.
memo
If you press the Reverse button without opening the LCD moni-
tor outwards, the image will be reversed on the LCD monitor.
If you are taking pictures in low light conditions, use the self-
timer to avoid camera shake when pressing the shutter release
button.
•
Using the Self-Timer
p.39
44
Download from Www.Somanuals.com. All Manuals Search And Download.
v ,
z
Rec.Mode
Applied Function
Set-up
3D image mode
Auto bracket
MENU
x .
c b
MENU
OK
Taking Stereo Pictures (3D image mode)
You can take 3D pictures using the LCD monitor and view them by
the parallel method or cross method. If you print out the 3D pic-
tures and look at them through the 3D image viewer provided, the
image will appear in three dimensions.
z Select [3D Image mode] on the [Applied Function] menu
and press the four-way controller ( ).
x Use the four-way controller (
3D image mode
) to select [Parallel] or
Applied Photo Mode Parallel mode
[Cross].
To view the picture with the 3D
image viewer, select [Parallel].
MENU
OK
You can also view it without the
image viewer.
c Press the OK button.
v Press the shutter release button
while watching the capture guide.
Take the picture so that the subject
is in the shooting zone in the mid-
dle. The first image is taken and
[Move camera to right] appears on
the LCD monitor.
3
04/23/2002
11:19
Shooting zone
b Press the OK button.
Even if you press the shutter release button halfway, you can
proceed to take the second image.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
n Move the camera to the right
3
without changing your stance.
m Overlap the images.
The first image will appear in a
semi-transparent state on top of the
second image. Compose the picture
so that the first semi-transparent
image is superimposed on the out-
lines of the second real image.
04/23/2002
11:19
If the overlapping images are hard to see, use the four-way
controller to move the semi-transparent image and superim-
pose it on the real image.
The semi-transparent section is lengthened sideways
and moves up and down when the four-way controller is
pressed.
The semi-transparent section is lengthened longways
and moves right and left when the four-way controller is
pressed.
, Press the shutter release button.
Continue
The second image will be taken.
Continue
. Use the four-way controller (
Cancel
to choose whether to
)
OK
continue shooting.
Choose whether to continue or end
3D shooting and press the OK button.
•
3D image picture cannot be taken when the Quality level is set
to TIFF.
memo
•
•
Press the Menu button to end 3D shooting.
A clear three-dimensional effect will not be achieved if the two
images are taken in widely different positions (heights) or are
not straight. When taking a person, you are recommended to
ask your model to stay as still as possible and to take the sec-
ond picture as quickly as you can. It is easier to take the pic-
tures if you use a tripod or appropriate base.
•
As a guide, the camera should be moved about 1/40 of the dis-
tance between the camera and the subject. For example, if the
subject is 3m away, the distance the camera should be moved
will be 3m × 40=7.5cm.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
However, as the way people see three-dimensional images dif-
fers from person to person, there is no need to be too con-
cerned. Refer to the table below for a simple guide to how far to
move the camera.
Distance to subject 0.1 m
Camera movement 0.5 cm
0.3 m
1 cm
0.5 m
1 m
3 m
5m
1.5 cm 2.5 cm 7.5 cm 13 cm
● Viewing 3D pictures by the parallel method and cross
method
As our eyes are positioned about 6~7cm apart, there is a very
slight deviation between what we see with our right eye and what
we see with our left eye. The difference is processed by our brain
to produce a three-dimensional image. This principle is applied to
taking and viewing 3D pictures.
3D pictures can be viewed by the parallel method where the left
and right lines of vision are virtually parallel, as when looking at a
distant scene, or the cross method where the left and right lines of
vision are crossed, as when you cross your eyes. A certain
amount of practice may be necessary to view 3D pictures without
using the viewer.
●
How to Assemble the 3D Image Viewer
Assemble the 3D image viewer supplied with the camera as
shown below.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
●
How to view 3D pictures using the 3D image viewer
Print out the pictures so that they are about 11cm or 12cm wide
and place the divider of the 3D image viewer in the middle of the
two.
Viewing the images with a PC or Macintosh
p.82 or p.101
•
As the distance between the left and right eyes differs from per-
son to person, some people may have difficulty obtaining a
three-dimensional effect even when looking at prints that are
the same size. It may be especially difficult if the pictures are
very large or very small. Try different sizes until the right effect
is achieved.
memo
• Never look at the sun through the 3D image viewer.
• Do not leave the 3D image viewer where it is exposed to
direct sunlight as this may lead to fire.
Caution
48
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Example of a 3D picture
49
Download from Www.Somanuals.com. All Manuals Search And Download.
n
Rec.Mode
Applied Function
Set-up
3D image mode
Auto bracket
MENU
z
x c v
b
MENU
OK
Automatically Changing the Shooting Conditions (Auto bracket)
You can take pictures in succession while automatically changing
the exposure, white balance, saturation, sharpness and contrast
settings. Three pictures are taken in succession with different
exposure settings. The other settings are automatically set for
each picture.
z Select [Auto bracket] on the [Applied Function] menu.
x Use the four-way controller (
Auto bracket
) to select the conditions for
Applied Photo Mode Ex.Bracketing
Step
0.3EV
bracket shooting.
MENU
Auto bracket
OK
c Press the four-way controller (
to select [Ex. Bracketing] or
[white balance].
)
Applied Photo Mode Ex.Bracketing
Step
0.3EV
The [Step] setting screen appears.
v Use the four-way controller (
) to set the steps.
MENU
OK
In addition to the NORMAL setting,
you can take the 3 pictures in steps
using a plus or minus setting.
b Press the OK button.
The Bracket mode is set.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
n Press the shutter release button.
m Use the four-way controller (
) to choose whether or
Continue
not you wish to continue bracket
shooting.
Continue
Cancel
Choose whether you wish to contin-
ue bracketing under the same condi-
tions or end bracketing and press
the OK button.
OK
•
•
Check the pictures you have taken using the Playback mode.
If you set auto bracket when you set the Continuous Shooting
mode, continuous shooting will be canceled.
memo
Playing Back Images
p.22
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Shooting Functions
z
Selecting a Focus Mode
● Focus Mode
None Auto
The camera is focused on the subject in the focusing
area when the shutter release button is pressed halfway.
Macro Mode
This mode is used when the distance to the subject is
approx. 10cm-50cm (0.33ft-1.64ft). The camera is
focused on the subject in the focusing area when the
shutter release button is pressed halfway.
Infinity-landscape mode This mode is used for taking distant objects.
Manual Focus Mode The subject is brought into focus manually.
z Press the
button in Capture mode.
The focus mode changes each time the button is pressed and
the setting is displayed on the LCD monitor.
The camera is ready to take the picture in the set focus mode.
•
•
The focus mode returns to [Auto] when the camera is turned off.
The default setting of the focus mode is [Auto]. When the focus
mode is [Auto], no icon is displayed on the LCD monitor.
memo
52
Download from Www.Somanuals.com. All Manuals Search And Download.
If you take a picture while looking through the viewfinder when
the focus mode is set on Macro, the range of the resulting pic-
ture may differ from what was seen in the viewfinder.
Caution
Manual Focus
When the mode is set on
, focus the camera on the subject
manually while observing the enlarged display in the middle.
increases the distance to the focusing position
decreases the distance to the focusing position
•
•
The Manual Focus mode is canceled when you exit the Capture
mode.
It is difficult to obtain the correct focus in Auto mode when tak-
ing pictures in a dark place. In this case, if you press the shutter
release button halfway, AF spotbeam will be emitted, enabling
the camera to focus more easily on the subject.
memo
53
Download from Www.Somanuals.com. All Manuals Search And Download.
z
EV Compensation
You can take pictures that are intentionally overexposed or under-
exposed.
z Press the four-way controller (
198
) in Capture mode.
Four-way controller (
)
increases the EV compensa-
tion to a positive (+) level
23/04/2002
–1.0 11:19
Four-way controller (
)
decreases the EV compensa-
tion to a negative (–) level
EV compensation level
The set level is displayed on the
LCD monitor.
•
•
The EV Compensation is disabled in the Auto mode.
If you press or one time, or set to 0, the set level
memo
displayed on the LCD monitor will go off after three seconds.
EV compensation is reset when power is off.
You can save the Exposure Compensation setting by the Exp.
comp. memory mode when the camera is being turned on.
•
•
Saving the EV Compensation
p.68
54
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Selecting the Flash Mode
The flash discharges automatically depending on the
light conditions.
None Auto
The flash will not discharge.
Flash Off
The flash discharges regardless of the brightness.
Flash On
This mode reduces the phenomenon of red eyes
caused by the light from the flash being reflected in
the subject’s eyes. The flash discharges automatically.
Auto +
Red-eye
Reduction
This mode reduces the phenomenon of red eyes
caused by the light from the flash being reflected in
the subject’s eyes. The flash will discharge regardless
of lighting conditions.
Flash On +
Red-eye
Reduction
•
The flash is off when the Capture mode is set to
shooting, or infinity-landscape mode.
, continuous
memo
• The flash discharges once as the auxiliary light for the photome-
try when taking a picture in the flash mode.
• In [Auto + Red-eye Reduction] and [Flash On + Red-eye
Reduction] modes, the flash discharges once to make subject’s
pupil smaller. And then, take a picture in the flash mode after a
brief interval.
z Press the
button in Capture mode.
The flash mode changes each time the button is pressed and
the set mode is displayed on the LCD monitor.
The flash lamp blinks red while the flash is charging. If the
flash lamp lights red when you press the shutter release but-
ton halfway after charging is completed, the camera is ready
to take the picture in the set flash mode.
Saving the Flash Mode
p.68
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Selecting the Recorded Pixels
You can choose the number of recorded pixels from [1600 ×
1200], [1024 × 768] and [640 × 480].
z Select [Resolution] from the
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
[Rec.Mode] menu.
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
x Use the four-way controller
(
) to change the size.
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Selecting the Quality Levels
You can choose the image compression rate.
TIFF
TIFF
The quality is the best and there is a high volume of
image data.
BEST
The quality is better and there is a high volume of
image data.
BETTER Standard level
GOOD The quality is good and there is a low volume
of image data.
z Select [Quality Level] from the
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
[Rec.Mode] menu.
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
x Use the four-way controller (
) to change the image quality.
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
•
•
•
If you select TIFF, the resolution is fixed at 1600 × 1210.
If you select TIFF, the digital zoom is disabled.
If you select TIFF, the 3D image picture cannot be taken.
memo
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x c
v
MENU
OK
Adjusting the Color Balance according to Lighting (White Balance)
You can take pictures in the actual colors that you see by adjust-
ing the white balance according to the light conditions.
AWB
Auto
The camera adjusts the white balance
automatically.
Daylight
Shade
Use this mode when taking pictures outside in
sunlight.
Use this mode when taking pictures outside in
the shade.
Tungsten
Light
Use this mode when taking subjects under
electric or other tungsten light.
Fluorescent
Light
Use this mode when taking subjects under
fluorescent light.
Manual
Use this mode when taking pictures by adjusting
the white balance manually.
z Select [White Balance] from the
White Balance
AWB
[Rec.Mode] menu.
x Press the four-way controller ( ).
The white balance screen will be
displayed.
MENU
OK
c Use the four-way controller (
)
to change the setting.
v Press the OK button twice.
The camera is ready to take the picture.
Saving the Color Balance
Download from Www.Somanuals.com. All Manuals Search And Download.
p.68
58
Manual Setting
z Select [ ] on the white balance screen.
x Point your camera at a blank sheet of paper so that it fills
the screen.
c Press the shutter release button.
White Balance
AWB
The white balance is automatically
adjusted, [Complete] is displayed on
the LCD monitor and the display
returns to the menu screen.
SHUTTER
Adjust
MENU
OK
v Press the OK button.
The camera is ready to take the picture.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Changing the AF Area (Focusing Area)
You can change the range and position of the autofocus area.
[
]
Normal range (Wide)
[
]
The autofocus range becomes smaller. (Spot)
z Select [Focusing Area] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
) to change the setting.
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
The AF area does not appear in the viewfinder. Always check the
focusing area on the LCD monitor.
memo
Save the AF Area
p.68
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the Light Metering Range to Determine the Exposure (AE Metering)
You can choose which part of the screen to use to measure the
brightness and determine the exposure.
Multi segment
Center-weighted The exposure is determined mainly by the center of the screen.
Spot The exposure is determined by the middle of the screen only.
The exposure is determined by the entire screen.
z Select [AE Metering] on the [Rec.Mode] menu.
x Use the four-way controller (
) to change the metering
mode.
Rec.Mode
Applied Function
Set-up
AE Metering
ISO Speed
Color
Instant Review
Memory
Auto
Full
0.5s
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
Saving the AE Metering Method
p.68
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the ISO Speed (ISO Speed)
You can select the ISO speed to suit the brightness of the sur-
roundings.
●
ISO Speed
Auto
100
The camera sets the speed automatically.
Produces sharp images with little or no noise. Reduces the
shutter speed in low light conditions.
200
Increases the shutter speed in low light conditions but there is
more risk of noise.
z Select [ISO Speed] on the
Rec.Mode
Applied Function
Set-up
[Rec.Mode] menu.
AE Metering
ISO Speed
Color
Instant Review
Memory
Auto
Full
0.5s
x Use the four-way controller (
) to change the ISO
speed.
MENU
OK
c Press the OK button.
The camera is ready to take the pic-
ture.
Saving the ISO Speed
p.68
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Selecting the Color Mode (Color)
You can give atmosphere to your pictures by changing the colors
to black and white or sepia.
●
Color Mode
Full
The picture is taken in color
B & W
Sepia
The picture is taken in black and white.
The picture is taken in sepia.
z Select [Color] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
) to change the Color mode
setting.
AE Metering
ISO Speed
Color
Instant Review
Memory
Auto
Full
0.5s
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the Instant Review Time (Instant Review)
You can choose the Instant Review time from 0.5sec, 1sec, 2sec,
3sec, 5sec or Off (no display).
z Select [Instant Review] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
) to change the display time.
AE Metering
ISO Speed
Color
Instant Review
Memory
Auto
Full
0.5s
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
The Instant Review display setting is saved when the camera is
turned off.
memo
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the Sharpness (Sharpness)
You can choose whether you want the image to have sharp or soft
outlines.
z Select [Sharpness] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
) to change the setting from
[Hard (+)] to [Normal], [Soft (–)].
Exp.comp.memory
Continuous shooting
Sharpness
Saturation
Contrast
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the Saturation (Saturation)
You can set the saturation.
z Select [Saturation] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
) to change the setting from
[High (+)] to [Normal], [Low (–)].
Exp.comp.memory
Continuous shooting
Sharpness
Saturation
Contrast
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
z
x
c
MENU
OK
Setting the Contrast (Contrast)
You can set the contrast.
z Select [Contrast] on the [Rec.Mode] menu.
x Use the four-way controller (
Rec.Mode
Applied Function
Set-up
) to change the setting from
[High (+)] to [Normal], [Low (–)].
Exp.comp.memory
Continuous shooting
Sharpness
Saturation
Contrast
c Press the OK button.
The camera is ready to take the pic-
ture.
MENU
OK
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving the Settings (Memory)
Saving the Menu Items (Mode Memory)
You can choose whether you want the set values to be saved when the
camera is turned off. If you select
the status they were in immediately before the camera was turned off. If
you select (Off), the settings will be reset to the defaults when the cam-
(On), the settings will be saved in
era is turned off.
Item
Description
Default Setting
The setting on the
button is saved.
Flash
White Balance The [White Balance] setting on the [Rec.Mode] menu is
saved.
Focusing Area The [Focusing Area] setting on the [Rec.Mode] menu is
saved.
Digital Zoom
AE Metering
ISO Speed
The [Digital Zoom] setting on the [Rec.Mode] menu is
saved.
The [AE Metering] setting on the [Rec.Mode] menu is
saved.
The [ISO Speed] setting on the [Rec.Mode] menu is
saved.
Display
File No.
The LCD monitor display mode is saved.
The file number is saved. If a new CF card is inserted,
the sequential file number is assigned.
Menu items not included in [Memory] will also be saved in the set-
tings selected on the menus for each function when the camera is
turned off.
memo
68
Download from Www.Somanuals.com. All Manuals Search And Download.
z Press the Menu button in Capture
mode.
x Press the four-way controller
Rec.Mode
Applied Function
Set-up
AE Metering
ISO Speed
Color
Instant Review
Memory
Auto
Full
0.5s
(
) to select the [Memory]
menu.
MENU
OK
c Press the four-way controller ( ).
Memory
[Memory] menu will be displayed.
WB
AF
v Use the four-way controller (
) to select the item.
b Use the four-way controller (
MENU
OK
) to switch
n Press the OK button.
The camera is ready to take the picture.
and
.
Saving the Exposure Compensation Setting
You can choose whether or not to save the exposure compensa-
tion setting when the camera is turned on.
Rec.Mode
Applied Function
Set-up
Exp.comp.memory
Continuous shooting
Sharpness
Saturation
Contrast
z Press the Menu button in Capture
mode.
x Press the four-way controller (
to select the [Exp. comp. memo-
ry] menu.
)
MENU
OK
[Exp. comp. memory] menu will be
display.
c Use the four-way controller ((
) to switch between
and
v Press the OK button.
The camera is ready to take the picture.
(On)
.
(Off)
EV compensation is reset when the camera is turned off.
memo
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback/Erasing
Playing Back Images on the Camera
x
Mode dial
z
c
Playing Back Still Pictures
See “Playing Back a Single Image” (p.23).
Zoom Display
You can display images magnified up to four times. A guide to
operation is displayed on the LCD monitor during magnification.
z Set the mode dial to
and choose the image you want
).
to magnify with the four-way controller (
x Press
on the Zoom button.
The image will be magnified (1× to 4×).
● The following operations can be
performed while the magnified
image is displayed.
Four-way controller (
)
Moves the position to be magnified
Makes the picture bigger
Zoom button (
)
Zoom button (
Display button
)
Makes the picture smaller
Turns the guide marks on/off
c Press the OK button.
Zoom playback will end.
Movie pictures cannot be magnified.
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
70
Mode dial
z x c
Display button
Playing Back Movie Pictures
You can play back Movie pictures. A guide to operation is dis-
played on the LCD monitor during playback.
z
Set the mode dial to
and choose the movie picture you
want to play back with the four-way controller (
).
x Press the four-way controller ( ).
Playback will start.
100-0019
● The following operations can be
performed during playback.
Four-way controller (
Reverse playback
Four-way controller (
) :
) :
04/23/2002
11:19
Forward playback
Four-way controller (
) : Pause
Display button : Changes the Display mode
● The following operations can be performed while Pause is
engaged.
Four-way controller (
Four-way controller (
Four-way controller (
Display button :
) : Frame forward
) : Frame return
) : Releases the Pause function
Changes the Display mode
c Press the four-way controller ( ).
Playback ends.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Shooting Information (Display mode)
You can display information on the LCD monitor when shooting.
The information displayed can be changed by pressing the Display
button.
1 23
Display On
Information is displayed when
shooting.
100-0020
q Folder No. w File No.
e Protect symbol
r Shutter speed/Aperture
t Battery remaining
y Shooting date
1/1600
F2.8
04/23/2002
11:19
4
5
6
Display Off
No information is displayed when
shooting.
Display On
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode dial
z
x c
Nine-image Display
You can display nine images at the same time.
z Set the mode dial to
and choose an image with the
).
four-way controller (
x Press the OK button.
Nine images will be displayed with
the selected image in the center.
Choose an image with the four-way
controller (
).
If you press the four-way
controller( ) while an image on the
left row is selected, previous 9
images will be displayed. If you
Selected image
press the four-way controller(
)
while an image on the right row is
selected, next 9 images will be dis-
played.
c Press the OK button.
The screen will return to single-image display of the selected
image.
For movie pictures, the first frame will be displayed.
memo
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode dial
x
z c v
b
Slideshow
You can play back all the images on the CF card continuously.
z Set the mode dial to
which to start the slideshow with the four-way controller
).
and choose the image with
(
x Press the Menu button.
The [Playback] menu will be displayed.
c Select [Slideshow] with the four-
Playback
Set-up
way controller ( ).
Slideshow
DPOF
3s
v Use the four-way controller (
) to change the playback inter-
val.
MENU
OK
Choose from the following: 3s (3
sec), 5s (5 sec), 10s (10 sec), 20s
(20 sec), 30s (30 sec).
b Press the OK button.
Playback will start at the set interval.
n Press any button (except the shutter release button).
The slideshow will stop.
• The slideshow will continue until you press any button.
memo
•
In the case of movie pictures, when one movie picture has
been played through, the next movie picture will be played
regardless of the set playback interval.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing Images
x
Mode dial
z c
v
Erasing a Single Image
z Set the mode dial to
and choose the image you want
to erase with the four-way controller (
).
x Press the button.
Delete
100-0020
The [Delete] menu will be displayed.
Delete
Cancel
c Select [Delete] with the four-way
controller ( ).
ALL
MENU
OK
v Press the OK button.
•
•
You can also delete images from Instant Review (p.21) and
Easy View (p.22).
memo
You cannot erase protected images (with the
symbol).
75
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Mode dial
c
v
Erasing All Images
You can erase all the images on the CF card.
• Once erased, images cannot be restored.
• Protected images cannot be erased.
Caution
z Set the mode dial to
.
x Press the button twice.
Delete All
100-0020
The [Delete All] menu will be dis-
played.
Delete All
Cancel
MENU
c Select [Delete All] with the four-
way controller ( ).
OK
v Press the OK button.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Mode dial
z c
v
Protecting Images from Deletion (Protect)
You can protect images from being accidentally erased.
z Set the mode dial to
and choose the image you want
to protect with the four-way controller (
).
x Press the
button.
Protect
100-0020
The [Protect] menu will be displayed.
Protect
c Select [Protect] with the four-way
Unprotect
MENU
controller ( ).
ALL
OK
v Press the OK button.
•
•
Select [Unprotect] in step c above to release the Protect set-
memo
ting.
If the image is protected, the
image is played back.
symbol is displayed when the
Protecting All Images
You can protect all the images.
z Set the mode dial to
x Press the button twice.
The [Protect (All)] menu will be displayed.
.
c Select [Protect] with the four-way controller ( ).
v Press the OK button.
Even protected images will be erased by formatting a CF
card.
Caution
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Images on a TV
By using the video cable, you can capture and play back images
on a TV or other equipment with a video IN jack. Make sure that
both the TV and the camera are turned off before connecting the
cable.
z Open the terminal cover and connect the video cable.
x Connect the other end of the video cable to the image
input terminal of the TV.
c Turn the TV and camera on.
Changing the Video Output Format
p.105
The LCD monitor is always turned off when the camera is con-
nected to a TV.
memo
If you intend to use the camera for a long time, use of the AC
adapter (optional) is recommended. Refer to the operating manual
for the TV or equipment to which the camera is connected.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Printing Service
You can print the images on the CF card using a DPOF (Digital Print
Order Format) compatible printer or at a printing service.
z
Mode dial
x c v
b
Printing Single Image
Set the following items for each image.
● Copies
Set the number of prints up to a maximum of 99.
● Date
Specify whether you want the date inserted on the print or not.
z Press the menu button and select [DPOF] on the
[Playback] menu.
DPOF
100-0020
x Use the four-way controller (
)
to choose the image for which you
want to specify the number of
prints and press the four-way con-
troller ( ).
Copies
Date
01
On
DISP:ALL MENU
OK
The frame will move to [Copies].
79
Download from Www.Somanuals.com. All Manuals Search And Download.
c Use the four-way controller (
)
DPOF
100-0020
to select the number of prints and
press the four-way controller ( ).
The frame will move to [Date].
Copies
Date
01
On
DISP:ALL MENU
OK
v Use the four-way controller (
)
to select On or Off.
On : The date will be printed
Off : The date will not be printed
b Press the OK button.
Prints can be made according to the settings.
•
If DPOF settings have already been made for an image, the
previously set number of prints and On/Off date setting will be
displayed.
memo
• You cannot set the printing service for movie pictures.
• Depending on the printer or printing equipment at the
photo tab, the date may not be printed on the pictures even
if the DPOF setting was made.
Caution
80
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Mode dial
c v b
n
x
Printing All Images
z Select [DPOF] on the [Playback] menu.
x Press the Display button.
c Use the four-way controller (
to select the number of prints.
You can specify up to 99 prints.
)
DPOF All
100-0020
Copies
Date
01
v Press the four-way controller ( ).
On
MENU
OK
The frame will move to [Date].
b Use the four-way controller (
)
to select On or Off.
On : The date will be printed
Off : The date will not be printed
n Press the OK button.
Prints can be made according to the settings.
•
•
The setting for a single image will be cancelled.
memo
When you specify the number of prints in the DPOF setting, the
number applies to all the images. Before printing, check that the
number is correct.
•
The setting is not possible for movie pictures.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Images with Windows PC
By using the provided USB cable (I-USB2) or card reader and
image-browser software, you can transfer images recorded with
the camera to a PC and edit them or print them out.
This section explains how to view images on a PC using the pro-
vided USB driver and software (S-SW5).
About the included software
The included CD-ROM (S-SW5) contains the following software:
- USB driver
- Image viewing software (ACDSeeTM 3.1)
System environment
OS:
Windows 98/2000/Me
Windows XP Home Edition/Professional
Pentium or later recommended
CPU:
Memory: 64MB or more
Hard disk space: 15MB or more
Standard equipped USB port
To view movie pictures on your PC, Direct X 8.0 and Media Player
pre-installed on system, or QuickTime 3.0 or later are required.
For Windows Me/XP, Media Player pre-installed on system,
QuickTime 3.0 or later is required.
• Not compatible with Windows 95.
Caution
• When you connect the camera to your PC, you are recom-
mended to use the AC adapter. If the battery power runs
out while image data is being transferred, the data may be
lost.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the software
The procedures for installing the necessary software are
explained.
• The installation procedure varies depending on the version
of Windows (98/Me/2000). Before starting installation,
check which version of Windows you have on your PC. If
you are using Windows XP, see “Installing the USB Driver
(Windows XP)” (p.90) for installation instructions.
• If you are using Windows 2000 or Windows XP
(Professional), log in by the administrator before starting
installation. Refer to your PC’s operation manual for
instructions on how to log in.
Caution
Installing the USB driver (Windows 98/Me/2000)
z
x
Turn on your PC.
Set the included CD-ROM (S-SW5) in the CD-ROM drive.
c Turn the camera off, and connect the PC and camera
using an USB cable.
Make sure that the CF Card has been inserted into the cam-
era.
v Turn the camera on.
The PC recognizes the camera and the [Add New Hardware
Wizard] screen is displayed.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are using Windows 98, follow the procedure below to
install the software. For Windows Me, see p.86, and for
Windows 2000, see p.88.
●
Windows 98
b Click [Next].
n Select [Search for the
best driver for your
device (Recommended)],
and then click [Next].
m Select [Specify a loca-
tion], and then click
[Browse].
If any other item has been
selected, click the check
box to unselect it.
, Specify the [Win] folder
in the CD-ROM drive and
click [OK].
If you click the [+] symbol,
the folder will open and dis-
play the files inside.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
. Make sure that the [Win]
folder is selected and
click [Next].
⁄ Make sure that [penus-
bp.inf] is selected, then
click [Next].
Installation starts.
⁄ Click [Finish].
Installation is completed
and the [Wizard] screen is
closed.
⁄ Turn the camera off and restart your PC.
When Windows is up and running, turn the camera on.
Make sure that the CF Card has been inserted in the camera.
⁄ Double-click the [My
Computer] icon on the
desktop.
When the camera is turned
on, the Removable Disk
(Camera) icon appears in
the window.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Windows Me
b Select [Specify the location of
the driver (Advanced)], and
then click [Next].
n Select [Specify a location], and
then click [Browse].
If [Removable Media] has been
selected, click the check box to
unselect it.
m Specify the [Win] folder in the
CD-ROM drive and click [OK].
If you click the [+] symbol, the
folder will open and display the
files inside.
, Make sure that the [Win] folder
is selected and click [Next].
. Make sure that [penusbp.inf] is
selected, then click [Next].
Installation starts.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
⁄ Click [Finish].
Installation is completed and the
[Wizard] screen is closed.
⁄ Turn the camera off and restart your PC.
When Windows is up and running, turn the camera on.
Make sure that there is a CF card in the camera.
⁄ Double-click the [My Computer]
icon on the desktop.
When the camera is turned on,
the Removable Disk (Camera)
icon appears in the window.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Windows 2000
b Click [Next].
n Select [Search for the best dri-
ver for your device], and then
click [Next].
m Select [Specify a location], and
then click [Next].
If any other item has been select-
ed, click the check box to unselect
it.
, Click [Browse].
The [Files] screen is displayed.
. Select the [Win] folder in the
CD-ROM drive and make sure
that [penusbp.inf] is displayed.
And then click [Open].
88
Download from Www.Somanuals.com. All Manuals Search And Download.
⁄ Make sure that the [Win] folder
containing the files to be copied
is selected, and click [OK].
⁄ Make sure that [penusbp.inf] is
selected, then click [Next].
Installation starts.
⁄ Click [Finish].
Installation is completed and the
[Wizard] screen is closed.
⁄ Double-click the [My Computer]
icon on the desktop.
When the camera is turned on,
the Removable Disk (Camera)
icon appears in the window.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the USB driver (Windows XP)
z Turn on your PC.
x Set the CD-ROM (S-SW5) supplied with the camera in the
CD-ROM drive.
c Turn the camera off and connect the PC and camera
using the USB cable.
Make sure that the CF card has been inserted in the camera.
v Turn the camera on.
[New hardware has been located]
will appear on the task bar and
the [New Hardware Search
Wizard] screen will be displayed.
b Select [Install the software auto-
matically (Recommended)] and
click [Next].
90
Download from Www.Somanuals.com. All Manuals Search And Download.
n When [The software has been
successfully installed] message
appears, click [Finish].
Installation is completed and the
[Wizard] screen is closed.
If the screen for choosing an auto-
matic Windows operation is dis-
played, click [Cancel].
m Click [My Computer] from [Start]
menu.
After installing the software, make
sure that a Removable Disk
(Camera) has been added to [My
Computer].
In the case of Windows XP, if the CF card has a volume label
attached, the content of the volume label will be displayed instead
of [Removable Disk]. If the CF card is new and has not been for-
matted, the manufacturer and capacity of the card will be dis-
played.
memo
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing ACDSeeTM
When installing ACDSeeTM, recorded images can be viewed on
your PC.
z Turn on your PC.
x Set the CD-ROM (S-SW5) in the CD-ROM drive.
c Double click [My Computer].
v Double click the [CD-ROM drive] icon.
b Double click [English].
n Double click [setup.exe].
The Setup screen will appear. Follow the on-screen guidance
and enter the registration information.
m When the installation is completed, restart Windows.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the camera and PC
z Turn on your PC.
x Turn the camera off and connect the PC and camera
using an USB cable.
Make sure that the CF Card is inserted.
c Turn on the camera.
The camera will be
detected as
[Removable Disk] in
[My Computer].
•
Although images can be viewed and printed, image data is in
the CF card of the camera. To save the image data in the CF
card to another medium, refer to the instruction manual of your
PC and move or copy files using Explorer, etc.
You can edit images on your PC after moving or copying files
there.
In the case of Windows XP, if the CF card has a volume label
attached, the content of the volume label will be displayed
instead of [Removable Disk]. If the CF card is new and has not
been formatted, the manufacturer and capacity of the card will
be displayed.
memo
•
•
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing images on your PC
z Double click the [ACDSeeTM] icon on the desktop.
x Select the image to view.
Camera images can be found in [My Computer] ➝
[Removable Disk (or the name on the volume label on the CF
card, if there is one)] ➝ [DCIM] ➝ [xxxPENTX] (xxx is a 3-
digit numeral) folder.
You can also view movie pictures operating the above procedures.
memo
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnecting the camera from your PC
Disconnecting the camera from your PC (Windows 2000)
z Double click
(Hot Plug icon)
on the lower right task bar tray of
the desktop.
The [Remove Hardware] screen will
appear.
x Make sure [PENTAX USB Disk
Device] is selected and click
[Stop].
[Stop Hardware Device] screen will
appear.
c Make sure [PENTAX USB Disk
Device] is selected and click [OK].
A message will appear.
v Click [OK].
b Disconnect the USB cable from
your PC and camera.
For Windows 98/Me, there is no Hot Plug icon. When removing the
camera, turn off the camera and disconnect the USB cable.
memo
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnecting your camera from your PC (Windows XP)
z Click [Remove Hardware icon] on
the task bar.
x Make sure [PENTAX USB Disk
Device] is selected and click
[Stop].
c Make sure [PENTAX USB Disk
Device] is selected and click [OK].
v A message confirming removal of
the hardware will appear. Turn the
camera off and disconnect your
camera from your PC.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Images with Macintosh
By using the provided USB cable or card reader and image-brows-
er software, you can transfer images recorded with the camera to
a PC and edit them or print them out.
This section explains how to view images on a PC using the pro-
vided USB driver and software.
About the included software
The included CD-ROM (S-SW5) contains the following software:
- USB driver
- Image viewing software (ACDSeeTM
)
System environment
OS:
CPU:
Mac OS 8.6 or later (QuickTime 4.0 or later required)
Power PC 266MHz or higher
Memory: 8MB or more
Hard disk space: 6MB or more
Standard equipped USB port
To view movie pictures on your Macintosh, QuickTime 4.0 or later
pre-installed on system is required.
memo
When you connect the camera to your PC, you are recom-
mended to use the AC adapter. If the battery power runs out
while image data is being transferred, the data may be lost.
Caution
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the software
The procedures for installing the necessary software are
explained.
Installing the USB driver (Only for Mac OS 8.6)
z Turn on your Macintosh.
x Set the included CD-ROM (S-SW5) in the CD-ROM drive
of your Macintosh.
c Copy the following 2 files to the [Extensions] folder
within the System folder.
PENTAX-USB Storage Driver
PENTAX-USB Storage Shim (E)
v Restart your Macintosh.
For MacOS 9.x or later, there is no need to install the USB driver.
memo
Installing ACDSeeTM
When installing ACDSeeTM, recorded images can be viewed on
your Macintosh.
z Turn on your Macintosh.
x Set the included CD-ROM (S-SW5) in the CD-ROM drive
of your Macintosh.
c Double click [English] on the CD-ROM (S-SW5).
v Follow the on-screen guidance and enter the registration
information and proceed with the installation.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the camera and your Macintosh
z Turn on your Macintosh.
x Turn off the camera and connect your Macintosh and
camera using an USB cable.
Make sure that the CF Card is inserted.
c Turn on the camera.
The camera will be detected as [untitled] on the desktop. The
folder name can be changed as desired.
•
•
Although images can be viewed and printed, image data is in
the CF card of the camera. To save the image data in the CF
card to another medium, refer to the instruction manual of your
Macintosh and move or copy files.
You can edit images on your Macintosh after moving or copying
files there.
If the CF card has a volume label attached, the content of the
volume label will be displayed instead of [Removable Disk]. If
the CF card is new and has not been formatted, the manufac-
turer and capacity of the card will be displayed.
memo
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing images on your Macintosh
z Double click the [ACDSeeTM] folder on the hard drive.
x Double click the [ACDSeeTM] program icon.
c Choose an image you wish to view.
Camera images can be found in the [untitled] ➝ [DCIM] ➝
[xxxPENTX] (xxx is a 3-digit numeral) folder on the desktop.
•
•
You can also view movie pictures operating the above proce-
dures.
If the CF card has a volume label attached, the content of the
volume label will be displayed instead of [Removable Disk]. If
the CF card is new and has not been formatted, the manufac-
turer and capacity of the card will be displayed.
memo
Disconnecting the camera from your Macintosh
z Drag the [untitled (or the name on the volume label on
the CF card, if there is one)] folder on the desktop to
Trash.
x Remove the USB cable from your Macintosh and camera.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Camera Settings
How to recall the [Set-up] menu
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
Menu button
Four-way controller
OK button
MENU
OK
Formatting a CF Card
Formatting will delete all the data on the CF card.
• Do not open the CF card cover while the card is being for-
matted. The card may be damaged and become unusable.
• Formatting will delete protected data too.
Caution
z Select [Format Card] on the [Set-up] menu.
x Press the four-way controller ( ).
The Format screen will be displayed.
c Select [Format] with the four-way controller ( ).
v Press the OK button.
memo
Formatting will start. When formatting is completed, the camera is
ready to capture or play back images.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
Twice (in Full, night scene
and movie modes)
Format
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
Once (in Playback and
auto mode)
MENU
Setting the Date Style
You can set the style in which the date is displayed on the camera.
Choose [mm/dd/yy], [dd/mm/yy] or [yy/mm/dd].
z Select [Date Style] on the [Set-up] menu.
x Use the four-way controller (
) to change the date
style.
c Press the OK button.
The camera is ready to capture or play back images with the
selected date style.
memo
The time is set by [Date Adjust].
103
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [Set-up] menu
Rec.Mode
Applied Function
Set-up
Format
MENU
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
Menu button
Four-way controller
OK button
MENU
Changing the Date/Time
You can change the initial date and time settings.
z Select [Date Adjust] on the [Set-up] menu.
x Press the four-way controller ( ).
The date screen will be displayed.
See “Initial Settings” (p.15) for the setting procedure.
Changing the Display Language
You can change the language in which the menus, error mes-
sages, etc. are displayed.
z Select [Language] on the [Set-up] menu.
x Press the four-way controller ( ).
The language setting screen will be displayed.
c Use the four-way controller (
) to select the lan-
guage.
v Press the OK button.
The menus will be displayed in the selected language.
b Press the OK button.
The camera is ready to take or play back images.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
Twice
Rec.Mode
Applied Function
Set-up
(in Capture
mode)
Format
Language/
Video Out
Sleep Timeout
Brightness Level
Reset
English
NTSC
1m
Six times
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
Once
(in Playback
mode)
MENU
MENU
OK
Changing the Video Output Format
You can select the output format (NTSC or PAL) for taking or play-
ing back images on a TV monitor.
z Select [Video Out] on the [Set-up] menu.
x Use the four-way controller (
) to change the video
output format.
c Press the OK button.
The camera is ready to take or play back images.
Setting the Beep
The beep sound can be turned on and off.
z Select [Beep] on the [Set-up] menu.
x Use the four-way controller (
) to select
(On) or
(Off).
c Press the OK button.
The camera is ready to take or play back images.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [Set-up] menu
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
Resolution
MENU
Quality Level
White Balance
Focusing Area
Digital Zoom
Menu button
Four-way controller
OK button
MENU
OK
Setting the World Time
The city and time selected in “Initial Settings” (p.15) serve as the
World Time setting.
You can display the time in a city other than the Home Time city
(World Time) when shooting or playing back.
z Select [World Time] on the [Set-up] menu.
x Press the four-way controller ( ).
World Time
The World Time screen will be dis-
NYC 04/23/2002
11:19
played.
NYC 04/23/2002
c Switch
(On) and
(Off) with
).
11:19
the four-way controller (
MENU
OK
:
The time in the
country selected in World Time
will be displayed.
:
The time in the country select-
ed in Home Time will be dis-
played.
v Press the four-way controller ( ).
The frame will move to [World Time].
b Use the four-way controller (
) to select the World
Time city and press the four-way controller ( ).
The frame will move to [DST].
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec.Mode
Applied Function
Set-up
Twice
(in Capture mode)
Format
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
Once
(in Playback mode)
MENU
n Use the four-way controller (
) to change the [DST]
setting.
DST ON
DST OFF
m Press the four-way controller ( ).
The frame will move to [City].
Use the four-way controller (
city and DST setting.
) to change the Home Time
, Press the OK button.
The camera is ready to capture or play back images with the
time in the selected city.
See p.110 for the list of cities and code names.
memo
107
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [Set-up] menu
Rec.Mode
Applied Function
Set-up
1600×1200
AWB
MENU
Resolution
Quality Level
White Balance
Focusing Area
Digital Zoom
Menu button
Four-way controller
OK button
MENU
OK
Powersaving Function (Sleep Timeout)
You can set the LCD monitor to turn off automatically when no
operation is performed for a fixed time.
z Select [Sleep Timeout] on the [Set-up] menu.
x Use the four-way controller (
) to select [30sec],
[1min], [2min] or [Off].
c Press the OK button.
The camera is ready to take or play back images.
•
•
This function will not work in Playback mode.
This function is not available when playing back with the
slideshow and using the USB cable.
memo
Auto Power Off Function
The camera turns off automatically when no operation is per-
formed for a set time.
•
•
The camera turns off 3 minutes after the last operation.
If you do not perform any operation for one minute after the
menu is displayed, the menu will be closed.
memo
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Twice
(in Capture
mode)
Rec.Mode
Applied Function
Set-up
Rec.Mode
Applied Function
Set-up
Format
Language/
Video Out
Sleep Timeout
Brightness Level
Reset
English
NTSC
1m
Date Style
Date Adjust
World Time
Beep
mm/dd/yy
OK
Once
(in Playback
mode)
MENU
MENU
OK
Setting the Brightness Level
You can set the brightness of the LCD monitor.
z Select [Brightness Level] on the [Set-up] menu.
x Use the four-way controller (
) to select the bright-
ness level.
Press ( ) to make the LCD monitor darker and press ( ) to
make it brighter.
c Press the OK button.
The camera is ready to take or play back images.
Resetting to Default Settings (Reset)
You can reset all the settings other than the date and time, lan-
guage, video output format and date style.
z Select [Reset] on the [Set-up] menu.
x Press the four-way controller button ( ).
The Reset screen will be displayed.
c Use the four-way controller ( ) to select [Reset].
v Press the OK button.
The camera is ready to take or play back images.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
List of City Names
Refer to the following list of city and code names for setting the world time.
Code
PPG
HNL
ANC
YVR
SFO
LAX
YYC
DEN
MEX
CHI
City Names
Pagopago
Honolulu
Anchorage
Vancouver
San Francisco
Los Angeles
Calgary
Code
THR
DXB
KHI
City Names
Tehran
Dubai
Karachi
Kabul
KBL
MLE
DEL
CMB
KTM
DAC
RGN
BKK
KUL
VTE
SIN
Male
Delhi
Colombo
Kathmandu
Dacca
Denver
Mexico City
Chicago
Rangoon
Bangkok
Kuala Lumpur
Vientiane
Singapore
Phnom Penh
Ho Chi Minh
Jakarta
MIA
Miami
YTO
NYC
SCL
CCS
YHZ
BUE
SAO
RIO
Toronto
New York
San Diego
Caracas
Halifax
PNH
SGN
JKT
Buenos Aires
Sao Paulo
Rio de Janeiro
Madrid
HKG
PER
BJS
Hong Kong
Perth
MAD
LON
PAR
MIL
Beijing
London
SHA
MNL
TPE
SEL
ADL
TYO
GUM
SYD
NOU
WLG
AKL
Shanghai
Manila
Paris
Milan
Taipei
ROM
BER
JNB
IST
Rome
Seoul
Berlin
Adelaide
Tokyo
Johannesburg
Istanbul
Guam
CAI
Cairo
Sydney
JRS
MOW
JED
Jerusalem
Moscow
Noumea
Wellington
Auckland
Jeddah
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages
Messages such as the following may be displayed on the LCD monitor
during camera operation.
Memory card full
The CF card memory is full and no more
images can be saved. Insert a new CF card
or delete unwanted images. (p.13, p.75)
Change the quality/size and try again. (p.56,
p.57)
No images in camera
There are no images on the CF card.
Camera can not display this You are trying to play back an image in a
image
format not supported by this camera. You
may be able to display it on another brand
of camera or PC.
This image is protected
The image you are trying to delete is a pro-
tected image. (p.77)
No card in camera
Battery depleted
There is no CF card in the camera. (p.13)
The battery is exhausted. Charge the lithi-
um battery or replace with a new battery.
(p.10, p.11)
Battery depleted. The image As the power ran out, the image you just
is not stored.
captured has not been saved. Charge the
lithium battery or replace with a new battery
and take the picture again. (p.10, p.11)
Memory card error
Shooting and playback are impossible due
to a problem with the CF card. Try display-
ing on a PC.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
This card is not formatted
The card you have inserted is unformatted
or has been formatted on a PC or other
device. (p.102)
Image recording...
Movie recording...
Changing setting
Formatting...
The image is being recorded on the CF
card.
The movie picture is being recorded on the
CF card.
The protect setting or DPOF setting is
being changed.
The CF card is being formatted.
Deleting image...
The image is being deleted.
Image folder can not be cre- The largest file number is assigned to an
ated.
image and no more images can be saved.
Insert a new CF card or format the CF
card.
3D image cannot be select- The Quality level is set to TIFF. The 3D
ed with TIFF.
image picture cannot be taken. Set to
another Quality level.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause
Remedy
Power will not
come on
Battery is not installed Check battery is installed. If
not, install battery.
CF card cover is open Close CF card cover.
Battery is installed
incorrectly
Check orientation of battery.
Reinsert battery as indicated by
(+)(-) inside the battery chamber.
Battery power is low
LCD monitor is set to
Insert a new battery or use
the AC adapter.
No image on
Press Display button to turn
LCD monitor on. (p.34, 72)
the LCD monitor OFF
Camera is connected to LCD monitor remains off
TV
while camera is connected to
TV.
Image is displayed but Image on LCD monitor may
is hard to see
be hard to see when taking
pictures outside in sunlight.
Adjust the brightness of the
LCD monitor. (p.109)
Shutter release Camera is set to Play
Set mode dial to
.
or
button will not
release
mode
Flash is charging
When flash lamp blinks red,
flash is charging and no pic-
tures can be taken. Lamp
lights red when charging is
completed.
No available space on Insert CF card with available
CF card
space or delete unwanted
images. (p.13, 75)
Recording
Wait until recording is fin-
ished.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
Subject is not in Subject difficult to focus Subjects difficult to focus on
focus
on
using autofocus: objects with
little contrast (blue sky, white
walls, etc.), dark objects, fine-
ly patterned objects, fast-
moving objects, scenery
through window or net, etc.
Lock focus on another object
located at same distance
(press shutter release button
halfway), then aim at target
and press shutter release
button fully.
Subject is not in focus- Position subject in square
ing area
frame (focusing area) in mid-
dle of LCD monitor. If the
subject is outside the focus-
ing area, aim the camera at
the subject and lock focus
(press shutter release button
halfway), then compose pic-
ture and press the shutter
release button fully.
Subject is too close
Set focus mode on
. (p.52)
Focus mode is set on
Normal pictures will be out of
focus if taken with focus
mode set on
.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
Picture is dark
Subject is too far away Picture becomes dark if sub-
ject is too far away. Take pic-
ture within range of flash.
Background is dark
When taking a picture of a
person against dark back-
ground, such as night scene,
the person may appear dark if
the flash does not reach
background even with correct
exposure. Set to
mode to
ensure both person and back-
ground are clear. (p.36)
Flash does not Flash mode is set to
Set to Auto or . (p.55)
fire
Off
The Capture mode is
Flash will not fire in these
modes.
set to
continuous
,
shooting, or Infinity-
landscape mode.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
Type
Effective Pixels
Sensor
Fully automatic compact-type digital still camera with built-in zoom lens
2.0 megapixels
2.11 megapixels (total pixels) 1/2.7 inch interline transfer CCD with
a primary color filter
Recorded Pixels Still
1600 × 1210 pixels (TIFF only), 1600 × 1200, 1024 × 768 pixels,
640 × 480 pixels
Movie 320 × 240 pixels
Sensitivity
Auto, manual (equivalent to ISO 100, 200)
File Format
Still
JPEG (Exif2.2), TIFF, DCF, DPOF
Movie AVI (Open DML Motion JPEG), 15fps
Quality Level
Excellent, Superior, Very Good, Good
Storage Medium CompactFlash (CF) card Type I
Image Storage Capacity
Quality levels
Recorded pixels
TIFF
Best
—
Better
—
Good
Movie images
(
)
(
)
(
)
1600 × 1210
2
—
—
—
—
—
2
1600 × 1200
1024 × 768
640 × 480
320 × 240
—
—
—
—
Approx. 14 Approx. 29 Approx. 64
Approx. 26 Approx. 53 Approx. 94
Approx. 53 Approx. 94 Approx. 133
—
—
—
• Exposure capacity when using a 16MB CF card
White Balance
Color Modes
Lens
Auto, Daylight, Shade, Tungsten Light, Fluorescent Light, Manual
Color, B&W, Sepia
Focal Length
5.8 mm–17.4 mm (Equivalent to 38 mm–114 mm
in 35 mm format)
F2.6–F5.0
Aperture
Lens Composition 6 elements in 5 groups (one aspherical element)
Zoom type Electrically driven
Picture Range 38.4 mm × 28.5 mm (screen is filled) (using macro
mode or manual focus at max. WIDE position)
Lens Barrier
Electrically driven
Digital Zoom
Viewfinder
Capture mode Max. 2.5x (Combines with 3x optical zoom to give
zoom magnification equivalent to 7.5x)
Type
Real-image zoom viewfinder
Wide 0.41x, Tele 1.13x
Magnification
116
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Monitor
1.6 inch TFD color LCD monitor (with backlight/brightness adjust-
ment)
With 180° swing out function
Playback Function Single-frame, 9-frame index, enlargement (max. 4x), scroll,
slideshow, movie playback
Focusing System
Type
TTL contrast detection autofocus system
Focusing Range Normal 0.4 (1.31 ft) to infinity (zoom fully
extended)
(From lens front) Macro 0.1 m (0.33 ft)–0.5 m (1.64 ft) (full zoom
range)
Landscape Infinity (zoom fully extended)
Focus Lock
By half-pressing shutter release button
Manual Focus
0.1m to infinity
Exposure Mechanism AE Metering
TTL metering by sensor (Multi-seg-
ment, Center-weighted, Spot)
Auto, Full, Night Scene, Movie
Exposure Modes
Exposure Compensation
Movie
2 EV(Set in 1/3 EV steps)
Recording time approx. 1 sec–30 sec.
Shutter
Flash
Type
Speed
Electronic/mechanical shutter
Approx. 1/1500 sec.–4 sec.
Type
Flash Modes
Auto flash with red-eye reduction function
Auto, Flash Off, Flash On, Auto + Red-eye
Reduction, Flash On + Red-eye Reduction
Working Range Wide Approx. 0.7 m–5.0 m (ISO 200)
Tele Approx. 0.5 m–2.7 m (ISO 200)
Drive Modes
Self-timer
Single-frame, Continuous, Self-timer
Electronic control type, delay time: approx. 10 sec.
World Time setting for 62 cities (28 time zones)
Time Function
Power Supply
One CR-V3 lithium battery pack, two R6/AA batteries (alkaline,
NiMH, lithium), AC adapter (optional)
In/Out Port
USB/Video terminal (PC communication type USB1.1), external
power supply terminal
Video Output Format NTSC, PAL
Size
103.5(W) × 63.5(H) × 42(D) mm (excluding operating members)
180 g (excluding batteries and CF card)
Weight
Weight when shooting 230 g (including battery and CF card)
Accessories CR-V3 lithium battery pack, 3D image viewer, USB cable, soft-
ware (CD-ROM), video cable, strap, operating manual
117
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY POLICY
All Pentax cameras purchased through authorized bona fide photographic
distribution channels are guaranteed against defects of material or workman-
ship for a period of twelve months from date of purchase. Service will be ren-
dered, and defective parts will be replaced without cost to you within that
period, provided the equipment does not show evidence of impact, sand or
liquid damage, mishandling, tampering, battery or chemical corrosion, opera-
tion contrary to operating instructions, or modification by an unauthorized
repair shop. The manufacturer or its authorized representatives shall not be
liable for any repair or alterations except those made with its written consent
and shall not be liable for damages from delay or loss of use or from other
indirect or consequential damages of any kind, whether caused by defective
material or workmanship or otherwise; and it is expressly agreed that the lia-
bility of the manufacturer or its representatives under all guarantees or war-
ranties, whether expressed or implied, is strictly limited to the replacement of
parts as hereinbefore provided. No refunds will be made on repairs by non-
authorized Pentax service facilities.
Procedure During 12-month Warranty Period
Any Pentax which proves defective during the 12-month warranty period
should be returned to the dealer from whom you purchased the equipment or
to the manufacturer. If there is no representatives of the manufacturer in your
country, send the equipment to the manufacturer, with postage prepaid. In
this case, it will take a considerable length of time before the equipment can
be returned to you owing to the complicated customs procedures required. If
the equipment is covered by warranty, repairs will be made and parts
replaced free of charge, and the equipment will be returned to you upon com-
pletion of servicing. If the equipment is not covered by warranty, regular
charges of the manufacturer or of its representatives will apply. Shipping
charges are to be borne by the owner. If your Pentax was purchased outside
of the country where you wish to have it serviced during the warranty period,
regular handling and servicing fees may be charged by the manufacturer’s
representatives in that country. Notwithstanding this, your Pentax returned to
the manufacturer will be serviced free of charge according to this procedure
and warranty policy. In any case, however, shipping charges and customs
clearance fees to be borne by the sender. To prove the date of your purchase
when required, please keep the receipt or bills covering the purchase of your
equipment for at least a year. Before sending your equipment for servicing,
please make sure that you are sending it to the manufacturer’s authorized
representatives or their approved repair shops, unless you are sending it
directly to the manufacturer. Always obtain a quotation for the service charge,
and only after you accept the quoted service charge, instruct the service sta-
tion to proceed with the servicing.
•
•
This warranty policy does not affect the customer’s statutory rights.
The local warranty policies available from Pentax distributors in some
countries can supersede this warranty policy. Therefore, we recommend
that you review the warranty card supplied with your product at the time
of purchase, or contact the PENTAX distributor in your country for more
information and to receive a copy of the warranty policy.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
For customers in the USA
STATEMENT OF FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not approved by the party responsible for com-
pliance could void the user’s authority to operate the equipment.
This equipment has been tested and found comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radi-
ate frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
This Class B digital apparatus meets all requirements of
the Canadian Interference - Causing Equipment Regulations.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
The CE Mark is a Directive conformity mark of the European
Community.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for
Class B Personal Computers and Peripherals
We:
Pentax Corporation
Located at: 35 Inverness Drive East
Englewood, Colorado 80112 USA
Phone: 303-799-8000 Fax: 303-790-1131
Declare under sole responsibility that the product iden-
tified herein, complies with 47CFR Parts 2 and 15 of
the FCC rules as a Class B digital device. Each prod-
uct marketed, is identical to the representative unit
tested and found to be compliant with the standards.
Records maintained continue to reflect the equipment
being produced can be expected to be within the vari-
ation accepted, due to quantity production and testing
on the statistical basis as required by 47CFR §2.909.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired oper-
ation. The above named party is responsible for ensur-
ing that the equipment complies with the standards of
47CFR §15.101 to §15.109.
Product Name: PENTAX Digital Still Camera
Model Number: Optio230
Contact person: Customer Service Manager
Date and Place: April, 2002, Colorado
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Asahi Optical Co., Ltd. 2-36-9, Maeno-cho, Itabashi-ku, Tokyo 174-8639,
JAPAN
(http://www.pentax.co.jp)
Pentax GmbH (European Headquarters)
Julius-Vosseler-Strasse 104, 22527 Hamburg,
GERMANY
(HQ - http://www.pentaxeurope.com)
(Germany - http://www.pentax.de)
Pentax U.K. Limited Pentax House, Heron drive, Langley, Slough, Berks
SL3 8PN, U.K.
(http://www.pentax.co.uk)
Pentax France S.A.
Pentax Benelux B.V.
12/14, rue Jean Poulmarch, 95106 Argenteuil Cedex,
FRANCE
(for Netherlands)
Spinveld 25, 4815 HR Breda, NETHERLANDS
(http://www.pentax.nl)
(for Belgium & Luxembourg)
Weiveldlaan 3-5, 1930 Zaventem, BELGIUM
(http://www.pentax.be)
Pentax (Schweiz) AG Widenholzstrasse 1 Postfach 367 8305 Dietlikon,
SWITZERLAND (http://www.pentax.ch)
Pentax Scandinavia AB P.O. Box 650, 75127 Uppsala, SWEDEN
(http://www.pentax.se)
Pentax Corporation
35 Inverness Drive East, Englewood, Colorado 80112,
U.S.A.
(http://www.pentax.com)
Pentax Canada Inc.
3131 Universal Drive, Mississauga, Ontario L4X 2E5,
CANADA
(http://www.pentaxcanada.ca)
http://www.digital.pentax.co.jp
•
•
Printed on recycled paper
Specifications and external dimensions are subject to change without notice.
Copyright © Asahi Optical Co.Ltd. 2002
01-200204 Printed in Japan
57172
Download from Www.Somanuals.com. All Manuals Search And Download.
|