MR2000-2/MR2000-3/MR2000S-2/MR2000S-3/MR2000U-2/MR2000U-3
MAGNETIC STRIPE READER
Rev.: B
FEATURES:
l
l
Double or triple tracks as indicated in MODEL IDENTIFICATION.
Built-in keyboard wedge interface or RS232 interface or USB interface as
indicated in MODEL IDENTIFICATION.
Built-in decoder
Dual directional operation
Interface cable included
l
l
l
l
Heavy duty die-cast case
SOME IMPORTANT NOTES:
FCC NOTES
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the
instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard
caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind.
Mustek Corp. further disclaims all implied warranties including without limitation any implied warranties of merchantability
or of fitness for a particular purpose. The entire risk arising out of the use or performance of the software and documentation
remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the stand-alone magnetic stripe
reader MR2000 series of Posiflex POS products. This series of products provide excellent flexibility and reliability in
application. This manual covers both operational and technical aspects of these units.
The manufacturer of the MR2000 series heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology. The
user may always obtain the most up to date information through our web site: http://www.posiflex.com.tw .
© Copyright Mustek Corp. 2002
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written
consent of Mustek Corp. the publisher of this documentation.
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service marks of their
respective owners.
MANUFACTURED BY: MUSTEK CORP.
AN ISO-9001 AND ISO-14001 CERTIFIED MANUFACTURER
p. - 1
P/N: 19030900020
Download from Www.Somanuals.com. All Manuals Search And Download.
l
Card data format
Data standard
IATA
Track 1 Track 2 Track 3 (Track 2)
MR2000-2/3 MR2000-3
ABA
THRIFT
JIS I
JIS II
Rear
side
Track used
Applicable to
models
MR2000-JIS
MR2000S-2/3 MR2000S-3
MR2000U-2/3 MR2000U-3
F2F (FM)
MR2000U-JIS
Recording method
Recording density 210 BPI 75 BPI
Recording capacity
characters / bits
210 BPI
75 BPI 210 BPI
79 / 7
40 / 5
107 / 5
40 / 5
72 / 7
Note: Data format for track 3 of ISO cards includes those specific in
AAMVA and CA DMV standards
l
Adjustable parameters:
ü
For MR2000-2/3 and MR2000S-2/3:
Changing the status of each selector in the 2 dotted areas that are the
enlarged images of the shaded areas on the control PCB determines parameters
illustrated in following 2 tables. (S1 ~ S6 apply to MR2000S-2/3 only) (T3
applies to MR2000-3 and MR2000S-3 only) (for MR2000–2/3, software control
is applicable and available)
J2 J4
U3
U4
U2
U1
X1
S8 S7 S6 S5 S4 S3 S2 S1
OP4
SH10
SH1
LOCATIONS OF SELECTORS
on PCB inside die cast case
R6
C17
R5
T3
S9
TRACK 1 TRACK 2
T1 T2
T2
T1
Table 1
SELECTION & PARITY
DATA ALT + LEADING &
PARITY
TRACK 3
T3
FUNCTION CHECK
BITS
NUM STOP CODE
S4
S5
S6
S7
S9
STATUS
OFF
ON
EVEN
ODD
7
8
NO
YES
OFF
ON
ENABLED ENABLED ENABLED
DISABLED DISABLED DISABLED
SHORT
OPEN
SHORT OPEN
OPEN SHORT
OPEN
SHORT
SHORT
SHORT
DEFAULT
Table 2
BPS
DEFAULT
19200
9600
4800
2400
1200
600
300
150
SELECT
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
S1
S2
S3
p. - 3
MR2000 Series User’ s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ü
For MR2000U-2/3
Changing the jumper status indicated on the control PCB inside die cast
case determines parameters illustrated in the table below. (for MR2000U-JIS,
only J3 is applicable) (for MR2000U-2, T3 is not applicable)
T1
T2
T3
J1
J2
J3
CN2
U3
CN1
U1
JUMPER
FUNCTION
T1
TRACK 1
T2
TRACK 2
T3
TRACK 3
J1
J2
J3
LEADING /
STOP CODE
RESERVED CARD TYPE
STATUS
ENABLED ENABLED ENABLED DISABLED
DISABLED DISABLED DISABLED ENABLED
N.A.
N.A.
JIS II
ISO
SHORT
OPEN
SHORT
SHORT
SHORT
OPEN
OPEN
OPEN
DEFAULT
Note 1: To use the USB interface MSR in operating system without USB
support, please set USB keyboard enabled in BIOS (CMOS) setup.
Note 2: Since this USB interface MSR works as a USB keyboard which is
a normal HID (Human Interface Devices) in USB classification, no
special driver shall be required.
MR2000 Series User’ s Manual
p. - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|