Operating Instructions
TM
DLP Based Projector Commercial Use
Model No.
PT-D5600E
PT-D5600EL
PT-DW5000E
PT-DW5000EL
Read these instructions completely before operating this unit.
TQBJ 0201
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the
replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362.
Check for the ASTA mark
or the BSl mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is
replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is
obtained. A replacement fuse cover can be purchased from an Authorized Service Centre.
If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse
should be removed and the plug cut off and disposed of safely. There is a danger of
severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: –THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: –The wires in this mains lead are coloured in accordance with the following code: –
Green-and-Yellow: Earth
Blue:
Neutral
Live
Brown:
As the colours of the wire in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol
GREEN-AND-YELLOW.
or coloured GREEN or
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is
marked with the letter L or coloured RED.
FUSE
How to replace the fuse. Open the fuse compartment with
a screwdriver and replace the fuse.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
RASTER POSITION........................................................32
XGA MODE.....................................................................32
SXGA MODE...................................................................32
Changing the display language..............................32
OPTION1 settings.....................................................33
COLOR CORRECTION ..................................................33
CONTRAST MODE.........................................................33
AUTO SIGNAL ................................................................33
BACK COLOR.................................................................33
SUB MEMORY LIST .......................................................33
DVI EDID.........................................................................33
OPTION2 settings.....................................................34
ID.....................................................................................34
FRONT/REAR.................................................................34
DESK/CEILING ...............................................................34
LAMP SELECT................................................................34
LAMP POWER................................................................34
RS232C...........................................................................35
SYSTEM INFORMATION ...............................................35
FAN CONTROL1.............................................................35
FAN CONTROL2.............................................................35
FUNC1 ............................................................................35
AUTO POW.OFF.............................................................35
PASSWORD ...................................................................35
Displaying the internal test pattern........................36
Cycle of displayed internal test patterns..........................36
Setting the security..................................................36
Setting the password.......................................................36
Changing the password...................................................36
Setting the text ................................................................36
Changing the text ............................................................36
Setting the network..................................................37
Connecting the PC...................................................37
System requirements ......................................................37
Connection example........................................................37
Using the serial terminals .......................................38
Examples of connection .................................................38
Pin assignments and signal names.................................38
Communication conditions (Factory setting) ...................38
Basic format ....................................................................38
Control commands ..........................................................39
Cable specifications ........................................................39
Using the Remote 2 terminal...................................39
Indication of lamp monitor......................................40
Cleaning and replacement of air filter....................41
Procedure of cleaning .....................................................41
Replacing of lamp unit.............................................42
Timing of lamp unit replacement .....................................42
Lamp unit replacement steps ..........................................43
Using Web Browser Control ...................................45
Accessing from the Web browser....................................45
Password change page...................................................45
Basic control page...........................................................46
Detail control page ..........................................................47
Monitor information page.................................................47
Error information page.....................................................48
E-mail setup page ...........................................................49
DNS server setup page...................................................50
POP server setup page...................................................51
Ping test page .................................................................51
Contents of mail sent.......................................................52
Adjust clock page ............................................................52
Network config page........................................................53
Network status page........................................................53
Using the PJLink™ protocol...................................54
Supported commands .....................................................54
PJLink™ security authentication .....................................54
Before asking for service ........................................55
Specifications...........................................................56
Compatible Signal List ............................................58
Dimensions...............................................................59
Installation dimensions diagram ............................59
IMPORTANT SAFETY NOTICE..................................2
Precautions with regard to safety ............................5
Accessories................................................................7
Precautions on handling ...........................................8
Name and function of parts.......................................9
Remote control..................................................................9
Front and side of the projector ........................................11
Rear view of the main unit/Controls on rear panel ..........12
Side-mounted connection terminals................................13
Using the remote control unit.................................14
Loading dry cells .............................................................14
Effective range of remote control operation ....................14
Setting projector ID number to remote control ................15
Using the remote control as a PC mouse........................15
Using a wired remote control...........................................16
Installation ................................................................16
Projection schemes.........................................................16
Installation geometry .......................................................16
Projection distances by projection lens ...........................17
Calculation formulas for projection distance by lens types.......19
Connection ...............................................................20
Setup precautions ...........................................................20
Example of connecting with AV products........................21
Example of connecting with PCs.....................................21
Projection..................................................................22
Powering up the projector ...............................................22
Making adjustment and selection....................................22
Powering off the projector ...............................................23
Direct power off function..................................................23
How to install and remove the projection lens
(optional)...................................................................24
How to install the projection lens.....................................24
How to remove the projection lens..................................24
How to adjust the lens.............................................24
How to adjust the lens focus, lens zoom and lens
up/down position movement (optical shift) ......................24
How to adjust the lens position to the left or right............24
Automatic adjustment (AUTO SETUP)...................25
Using the FREEZE function ....................................25
Using the SHUTTER function..................................25
Using the digital zoom (– D.ZOOM +) function......25
On-screen menus.....................................................26
Structure of menu screens ..............................................26
Basic menu operations....................................................27
Returning to the previous page .......................................27
Menu items shown in transparent characters..................27
Menu items setting ..........................................................27
Resetting to the factory default........................................27
Adjusting the picture ...............................................28
PICTURE MODE.............................................................28
BRIGHT...........................................................................28
CONTRAST.....................................................................28
COLOR............................................................................28
TINT ................................................................................28
COLOR TEMP. ...............................................................28
WHITE GAIN...................................................................28
SHARPNESS ..................................................................28
NR ...................................................................................28
AI.....................................................................................29
TV-SYSTEM....................................................................29
SYSTEM..........................................................................29
Adjusting the position .............................................29
POSITION .......................................................................29
ASPECT..........................................................................29
ZOOM..............................................................................30
CLOCK PHASE...............................................................30
KEYSTONE.....................................................................30
How to use ADVANCED MENU...............................31
DIGITAL CINEMA REALITY ...........................................31
BLANKING ......................................................................31
INPUT RESOLUTION .....................................................31
CLAMP POS. ..................................................................31
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions with regard to safety
WARNING
If a problem occurs (such as no image) or if you notice smoke or a strange smell coming
from the projector, turn off the power and disconnect the power cord from the wall outlet.
• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
• Check that no more smoke is coming out, and then contact an Authorized Service Centre for repairs.
• Do not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to take the full weight
of the projector.
• If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could
result.
• Installation work (such as ceiling suspension) should only be carried out by a qualified technician.
• If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is dropped or the
cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.
• Continued use of the projector in this condition may result in fire or electric shocks.
• Contact an Authorized Service Centre for repairs.
Do not cover the air filter, the air inlet and exhaust vents.
• Doing so may cause the projector to overheat, which can cause fire or damage to the projector.
Do not overload the wall outlet.
• If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire
may result.
Do not remove the cover or modify it in any way.
• High voltages which can cause fire or electric shocks are present inside the projector.
• For any inspection, adjustment and repair work, please contact an Authorized Service Centre.
Use only the power cord supplied with the projector.
• Use only the supplied cord with three-pin plug and insert it only into a wall outlet that is connected to earth.
Otherwise, electric shock could result.
Clean the power cord plug regularly to prevent it from becoming covered in dust.
• If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in
fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth.
• If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.
Do not do anything that might damage the power cord or the power cord plug.
• Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively,
twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
• If the power cord is used while damaged, electric shocks, short-circuits or fire may result.
• Ask an Authorized Service Centre to carry out any repairs to the power cord that might be necessary.
Do not handle the power cord plug with wet hands.
• Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
• If the plug is not inserted correctly, electric shocks or overheating could result.
• Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not place the projector on top of surfaces which are unstable.
• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or
damage could result.
Do not place the projector into water or let it become wet.
• Failure to observe this may result in fire or electric shocks.
Do not disassemble the lamp unit.
• If the lamp section breaks, it may cause injury.
• The lamp unit has high internal pressure. If improperly handled, explosion might result.
• The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions
may result.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions with regard to safety
Do not place liquid containers on top of the projector.
• If water spills onto the projector or gets inside it, fire or electric shocks could result.
• If any water gets inside the projector, contact an Authorized Service Centre.
Do not insert any foreign objects into the projector.
• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing
so can result in fire or electric shocks.
After removing the battery from remote control unit, keep it away from the reach of
children.
• The battery can cause death by suffocation if swallowed.
• If the battery is swallowed, seek medical advice immediately.
Do not allow the + and - terminals of the battery to come into contact with metallic
objects such as necklaces or hairpins.
• Failure to observe this may cause the battery to leak, overheat, explode or catch fire.
• Store the battery in a plastic bag and keep it away from metallic objects.
Before replacing the lamp unit, be absolutely sure to disconnect the power plug from the
power outlet.
• Otherwise, electric shocks and/or damage may result.
When replacing the lamp, allow it to cool for at least one hour before handling it.
Do not bring your hands or other objects close to the air outlet port.
• Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand
heat close to this port [allow at least 50 cm of space], otherwise burns or damage could result.
Do not suspend the projector using only the hole used for the anti-theft clasp.
• The projector may fall or sustain damage, and possibly result in injury.
Caution
Do not set up the projector in humid or dusty places or in places where the projector may
come into contact with smoke or steam.
• Using the projector under such conditions may result in fire or electric shocks.
When disconnecting the power cord, hold the plug, not the cord.
• If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks
may result.
Always disconnect all cables before moving the projector.
• Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks
to occur.
Do not place objects or other projectors on top of this unit.
• The objects or projectors may lose their balance or fall off, causing possible injury. Further, stacking one
projector directly on top of another may cause the projectors to become deformed, resulting in possible
malfunctioning.
Do not short-circuit, heat or disassemble the battery or place it into water or fire.
• Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other injury
may result.
When inserting the battery, make sure the polarities (+ and -) are correct.
• If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the battery
compartment and surrounding area may result.
• Do not use a new battery together with an old battery.
• Remove the batteries if you are not going to use the projector for a prolonged period of time.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Use only the specified battery.
• If incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery
compartment and surrounding area may result.
Do not look into the lens while the projector is being used.
• Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
Do not place your skin into the light beam while the projector is being used.
• Strong light is emitted from the projector’s lens. If you place directly into this light, it can hurt or damage your skin.
Do not use the old lamp unit.
• The lamp section may break.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face
close to the broken pieces.
• Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces may cause
injury.
• If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical
advice immediately.
• Ask your dealer to replace the lamp unit and check the inside of the projector.
Disconnect the power cord plug from the wall outlet as a safety precaution before
carrying out any cleaning.
• Electric shocks can result if this is not done.
Ask an Authorized Service Centre to clean inside the projector at least once a year.
• If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.
• It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your
nearest Authorized Service Centre to clean the projector when required. Please discuss with the Authorized
Service Centre regarding cleaning costs.
Do not reach for the openings beside the optical lens, during horizontal or vertical
movements of the lens there is a injury hazard.
Indication based on the German law “Geräte - und Produktsicherheitsgesetz’
• Directive 2001/95/EC (Article5); Panasonic Marketing Europe Gmbh Hagenauer Str.43 65203 Wiesbaden
F.R.GERMANY
Accessories
Check that all of the accessories shown below have been included with your projector.
Remote control unit
Power cord
Battery for remote control unit
Lens cover
[N2QAYA000005 x 1]
for U.K.
[R03NW/2ST x 1]
[TKKL5244-1 x 1]
[K2CT3FZ00003 x 1]
for Continental
[K2CM3FZ00003 x 1]
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions on handling
Precautions on transport
Disposal
Make absolutely sure that the lens cap is in place
when transporting the projector or carrying it
around. Both the projector and the projection lens
are precision-made and, as such, are susceptible to
vibration and impacts. When transporting the
projector and lens or carrying them around, place
them in the boxes in which they were housed at the
time of purchase, and take care to keep them away
from vibration and impacts.
To discard the product, call the dealer or a
specialized dealer.
Precautions on use
To view clear images:
• The audience cannot enjoy high-contrast and
clear images if outside light or the illumination
interferes the screen surface. Draw window
curtains or blinds, turn off the lightings near the
screen or take other proper measures.
• In rare cases, wafture can occur on the screen
affected by the warm air from the exhaust port
depending on the environment.
Precautions on installation
Be sure to observe the following precautions when
installing the product.
Avoid installing the product in a place
Do not touch the surface of the
exposed to vibrations or impacts.
If the projector is installed in a place where
vibrations are transmitted from a source of
driving power and others or mounted in a car or
a vessel, vibrations or impacts may be
projection lens with bare hand.
If fingerprints or stains are left on the projection
lens surface, they are magnified and projected
on the screen. Keep your hands away from the
lens. Cover the lens with the supplied lens cap
when the projector is not used.
transmitted to the product to damage the internal
parts, causing failure. Install the product in a
place free from vibrations and impacts.
Lamp
A mercury lamp with high internal pressure is used
for the light source of this product. A high-pressure
mercury lamp has the following characteristics:
Do not move the projector while it is
operating or subject it to vibration or
impact.
The service life of its internal motors may be
shortened.
•
It may burst with a loud sound or end its life cycle
by not illuminating because of given impacts,
flaws, or deterioration due to used hours.
The life cycle of a mercury lamp varies according
to the individual difference or conditions of use.
In particular, turning the power on and off
frequently and/or repeatedly will greatly affect the
life cycle.
•
Do not install the projector near high-
voltage power lines or power sources.
The product may be exposed to interference if it
is installed in the vicinity of high-voltage electrical
power lines or power sources.
• In rare cases, it may burst shortly after the first
lighting.
Do not place the projector on a vinyl
sheet or carpet.
If a vinyl sheet sucked up and blocks the air filter
intake port, the internal temperature of the
projector may increase, which triggers the
protection circuit, turning off the power.
• The possibility of burst increases when the
lamp is used beyond the replacement time.
• If the projector is to be operated
continuously round the clock, consult your
dealer concerning the alternating lamp
operation function (lamp changer function).
Be sure to ask a specialized technician
when to install the product to a ceiling.
If the product is to be installed hanging from the
ceiling, purchase an optional hanging attachment
(for high ceiling: Model No. ET-PKD55) (for low
ceiling: Model No. ET-PKD55S) and call a
specialized technician for installation.
Cleaning and maintenance
Be sure to remove the power cord plug from the
receptacle before cleaning.
Use soft and dry cloth to clean the cabinet
If stains are hard to remove, use a cloth
dampened with a kitchen detergent solution
(neutral) and squeezed to wipe the cabinet and
finish with a dry cloth. If a chemical wipe is used,
follow its instructions.
Install the projector so that it will be
supported only by its bottom panel and
by none of its other parts or surfaces.
Do not place the projector over 2 700
m above sea level. When using it over
1 400 m above sea level, set the “Fan
Control1”, described on page 35, to
“HIGHLAND”.
Otherwise the life of the product may be
shortened. When using it over 2 700 m above
sea level, consult your dealer.
Do not clean the lens surface with fuzzy
or dusty cloth.
If dust adheres to the lens, it will be magnified
and projected on the screen.
Use a soft and clean cloth to wipe off dust.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Name and function of parts
Remote control
Function 1 (FUNC1) button (page 35)
< When the operation mode selector
set to Projector >
is
This button can control the functions set in
“FUNC1” of the “OPTION2” screen from Main
Menu.
Remote control operation indicator lamp
The lamp flashes when any remote control button
is pressed.
Digital Zoom (- D.ZOOM +) buttons (page 25)
Any portion of the picture can be zoomed in.
POWER ON ( I ) button (page 22)
LENS button (page 24)
Switches to the mode of projection lens
adjustment.
Turns on the power if the MAIN POWER has been
put to the “l” position.
POWER OFF ( ) button (page 23)
ON SCREEN button
This button turns on and off the on-screen
indication function.
Turns off the power if the MAIN POWER has been
put to the “l” position.
Input selector (RGB1, RGB2, DVI, VIDEO,
SYSTEM SELECTOR button
S-VIDEO) button
Use to toggle through the RGB1, RGB2, DVI-D,
VIDEO and S-VIDEO input ports.
Signal system switching (TV system/System) can
be done.
MENU button (page 27)
AUTO SETUP button (page 25)
Displays and clears the Main Menu. It can also
return to the previous screen when the menu is
displayed.
Pressing this button while projecting an image
automatically corrects the picture positioning on
the screen. While the auto setup feature is active,
a message “AUTO SETUP...” appears on the
screen.
Arrow
buttons (page 27)
Use these buttons to select an item on the menu
screen, change setting and adjust the level.
Also use them to enter the “SECURITY” password.
ID ALL button (page 15)
When two or more main units are used in the
system, this button switches to the mode to control
them simultaneously with a single remote control.
ENTER button (page 27)
Press this button to enter your menu selection or to
run function.
ID SET button (page 15)
When two or more main units are used in the
system, this button specifies the ID of the remote
control.
FREEZE button (page 25)
Press this button to freeze the image temporarily.
Standard (STD) button (page 27)
Press this button to restore the default factory
setting.
Operation mode selector (Computer/Numeric,
Projector) switch (page 15)
Put this selector to the right position to control the
projector and to the left position to control the PC
or use numeric buttons.
SHUTTER button (page 25)
Press this button to black out the image
temporarily.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Name and function of parts
Remote control wired terminal (page 16)
<When the operation mode selector
set to Computer>
is
To use the wired output terminal, connect the
remote control and the main unit with the M3
stereo mini jack cable available in the market.
PAGE UP/PAGE DOWN buttons
These buttons correspond to the PAGE UP/PAGE
DOWN buttons on PC’s keyboard.
Remote control transmitter window
Operate the remote control aiming at the remote
control receiver window on the main unit.
(
) buttons
These buttons correspond to the left and right
mouse buttons.
ENTER button
Moves the mouse cursor.
Numeric (0-9) buttons
In a system that uses a multiple number of
projectors, these buttons serve to specify a
particular projector.
They are also used to enter the password when
the password for service personnel needs to be
entered.
Click button (page 15)
This button corresponds to the left mouse button
when the operation mode is switched to the
Computer position.
• To use the remote control as a mouse,
please purchase an optional wireless
mouse receiver (model No.: ET-RMRC2).
Note
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Front and side of the projector
Status LED lights
(Refer to the figure
on the right.)
Side-mounted
connection terminals
(page 13)
Status LED lights
AC IN terminal (page 22)
Focus ring (page 24)
Connect the supplied line power cord into this
receptacle.
For focus adjustment.
Powered focus adjustment is also available.
Do not connect any other cable to this socket.
Temperature monitor (TEMP) (page 40)
Lighting or blinking of this lamp indicates an
abnormal condition of the internal temperature.
Air filter (page 41)
Burglar lock
Attach a commercial burglar prevention cable (e.g.,
from Kensington) to this lock port. It is compatible
with the Microsaver Security System from
Kensington. Contact details for this company are
given below.
Kensington Technology Group ACCO Brands Inc.
2885 Campus Drive San Mateo, CA94403
Tel (650)572-2700
LAMP1 monitor (page 40)
This lamp lights up when the time to replace lamp
unit 1 is reached. It also blinks if something
unusual occurs in the lamp circuit.
LAMP2 monitor (page 40)
This lamp lights up when the time to replace lamp
unit 2 is reached. It also blinks if something
unusual occurs in the lamp circuit.
Fax (650)572-9675
Power indicator (page 22)
The lamp lights in red when the MAIN POWER
switch is turned to “ | ” (on). It turns to green when
the POWER ON button of the remote control or the
main unit is pressed.
Clasp for attaching anti-theft chain
Attach a chain or other fastening device available
from a hardware store through this clamp.
Lens cap
Level-adjusting feet (page 22)
Cap the lens whenever the projector is left unused.
Use these feet to adjust the tilt of the projector.
(The leveling feet at the front left and right can be
adjusted.)
Ventilation holes
• Do not remove the upper cover (white top
panel).
Attention
Lens lock button (page 24)
Press this to remove the projection lens.
Projection lens
Lens for projecting images on the screen.
Lens left/right adjusting dial (page 24)
Turn this clockwise to move the screen to the left;
conversely, turn it counterclockwise to move it to
the right.
Remote control receiver window (front) (page 14)
This window receives the signal beam emitted from
the remote control.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Name and function of parts
Rear view of the main unit
Controls on rear panel
Controls on rear panel
Ventilation holes
DVI button (page 22)
Switches to DVI-D input.
Lamp unit cover
SHUTTER button (page 25)
The lamp unit is housed.
Press this button to black out the image
temporarily.
MAIN POWER switch (page 22)
Use this switch to turn on “I” and off “O” the main
power applied to the projector.
ENTER button (page 27)
Press this button to enter your menu selection or to
run function.
Remote control receiver window (rear) (page 14)
This also receives the signal beam coming from
the remote control.
LENS button (page 24)
Switches to the adjustment mode for lens focus,
zoom and shift (position).
POWER ON ( I ) button (page 22)
Turns on the power.
Arrow (
) buttons (page 27)
POWER OFF ( ) button (page 23)
Turns off the power.
Use to select an item on the menu screen, change
setting and adjust the level.
RGB1 button (page 22)
Also use them to enter the “SECURITY” password.
Switches to RGB1 input.
RGB2 button (page 22)
Switches to RGB2 input.
VIDEO button (page 22)
Switches to video input.
S-VIDEO button (page 22)
Switches to S-VIDEO input.
MENU button (page 27)
Displays and clears the Main Menu. It can also
return to the previous screen when the menu is
displayed.
The on-screen display (OSD) selection menu can
be displayed by holding down the menu key for at
least three seconds.
AUTO SETUP button (page 25)
Pressing this button while projecting an image
automatically corrects the picture positioning on
the screen.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Side-mounted
connection terminals
R/PR
G/Y
B/PB
SYNC/HD
VD
S-VIDEO IN
REMOTE 1
RGB 2 IN
OUT
DVI-D IN
LAN
VIDEO IN
RGB 1 IN
REMOTE 2
IN
SERIAL
IN
OUT
VIDEO IN terminal (page 21)
REMOTE1 lN/OUT terminal (page 16)
An input terminal for video signals. (BNC)
When two or more main units are used in the
system, they can be connected and controlled with
M3 stereo mini jack cable available in the market.
S-VIDEO IN terminal (page 21)
An input terminal for S-video signals.
(MIN4-pin DIN)
REMOTE2 IN terminal
This terminal complies with S1 signals and
automatically toggles between 16:9 and 4:3
according to the size of input signals.
The user can remotely control the main unit by
using an external control circuit to this terminal.
(D-SUB 9-pin female)
RGB 1 input (RGB 1 IN) terminal (page 21)
SERIAL IN terminal (pages 21, 38)
A terminal to input RGB or YPBPR signals. (BNC)
Use the RS232C serial terminal as an alternative
interface for controlling the projector from your PC.
(D-SUB 9-pin female)
RGB 2 input (RGB 2 IN) terminal (page 21)
A terminal to input RGB or YPBPR signals. (D-SUB
15-pin female)
SERIAL OUT terminal (pages 21, 38)
The signal applied to the serial input terminal
appears at this terminal. (D-SUB 9-pin male)
DVI-D IN terminal (page 21)
DVI-D signals are applied to this terminal. (24-pin
DVI connector)
LAN terminal (page 37)
This terminal is used to control the projector from
the PC. (10Base-T/100Base-TX compliant)
LAN terminal (10Base-T/100Base-TX)
Connect LAN cable.
LAN 10/100 lamp (Yellow)
Lights up when 100Base-TX
connected.
LAN LINK/ACT lamp (Green)
Lights up when connected.
Flashes when receiving/sending
signals.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control unit
Loading dry cells
Effective range of remote
When loading batteries into the battery
compartment of the remote control, make sure that
their polarities are correct.
control operation
The remote control should normally be aimed at either
the front or rear remote control receiver window on
the projector (figure 1). Otherwise, it may also be
aimed at the screen, which will reflect commands
back to the projector’s front receiver window as
illustrated in figure 2.
1.Open battery compartment lid.
Open the lid in the order of steps
and
.
The effective control range is approx. 7 metres from
the beam receiver on the front or rear.
Remote
control
Remote
control
30˚
30˚
30˚
30˚
(Front)
(Rear)
2.Insert the dry cells.
Into battery compartment, with their polarities
[Top view]
orientated as indicated (
,
) in the
compartment.
Remote
control
15˚
Remote
control
15˚
Accessory type-AAA dry
batteries (insert the negative
side first).
15˚
15˚
[Side view]
Figure 1
Screen
3.Close the battery compartment lid.
Replace the battery compartment lid over the
compartment and slide until it clicks.
Projector
Remote control
receiver window
(front)
Remote control
receiver window
(rear)
Remote control
Figure 2
• Do not drop the remote control unit.
• Do not expose remote control unit to
any liquid.
Attention
• When the remote control is aimed at
the screen, the effective control range
may be reduced due to the optical loss
by screen reflection.
Note
• Do not use NiCd batteries.
• The remote control may not function
properly if an object is in the light path.
• The remote control receiver may not
function properly in intense ambient
light such as fluorescent lamps.
Carefully site the projector so its
remote control receiver windows will
not be directly exposed to intense
light.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting projector ID number to remote control
Every projector has its ID number and the ID number of the controlling projector must be set to the remote
control in advance so that the user can operate the remote control. The ID number of the projector is set to
“ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.
Procedure of ID setting
Change the position of the operation mode selector switch to “Computer”.
Press the ID SET button, and within five seconds use the number (0 to 9) buttons to
enter the 2-digit ID number set by the projector.
Change the position of the operation mode selector switch to “Projector”.
However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the
projector (simultaneous control mode).
• Do not press the ID SET button accidentally or carelessly because the ID number on the remote
control can be set even when no projector is around.
Attention
If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID
SET button unless a numeric button is pressed within five seconds after the ID SET button is
pressed.
• Your specified ID number is stored in the remote control unit unless another one is specified later.
However, the stored ID will be erased if the batteries of the remote control are left exhausted.
When the dry cells are replaced, set the same ID number again.
• When specifying the ID number, enter a 2-digit number even if the ID has only one digit.
(Example: set “02” if the ID number is “2.”)
Using the remote control as a PC mouse
PAGE UP button
Operation mode selector switch
Put the knob to the Computer position.
ENTER button
• ENTER button
Pressing the front, rear, left and right edges of the
button moves the mouse cursor up, down, left and
right.
Right click ( ) button
Left click
( ) button
PAGE DOWN button
• Right click ( ) button
This button can be used as the right mouse button.
• Left click ( ) button
This button can be used as the left mouse button.
• PAGE UP button
Operation mode
selector switch
This button can be used as the Page Up button on
the PC keyboard.
• PAGE DOWN button
This button can be used as the Page Down button on
the PC keyboard.
• Click button
This button can be used as the left mouse button.
Click button
• To use the remote control as a mouse, please purchase an optional wireless mouse receiver
(model No.: ET-RMRC2).
Note
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Using the remote control unit
Using a wired remote control
Projection schemes
When multiple main units are connected in the
system, connect the units with the M3 stereo mini
jack cable available in the market to simultaneously
control the multiple main units with a single remote
control unit through the REMOTE1 IN/OUT
terminal. It is effective to use the wired remote
control in the environment in which an obstacle
stands in the light path or where devices are
susceptible to outside light.
Any of the following four projection schemes can be used
depending on user’s needs or viewing conditions.
Use “OPTION2” menu (chosen from the MAIN
MENU) to choose the appropriate projection
scheme (see page 34).
Projection Scheme 2
Table standing
Ceiling mount
R/PR
G/Y
B/PB
S
(Default position)
S-VIDEO IN
REMOTE 1
VIDEO IN
RGB 1 IN
REMOTE 2
IN
OUT
Installation geometry
After the projector is roughly positioned, picture size
and vertical picture positioning can be finely
adjusted with the powered zoom lens and lens tilt
mechanism.
Connect to the
secondary projector
M3 stereo mini
jack cable
Side view
(available in the
market)
With optional ceiling mount
bracket (ET-PKD55)
H
L
180
261
L
H
Screen
L
: Projection distance
SH : Image height
SW : Image width
H
: Distance from centre of lens to bottom edge
of projected image.
• Use two-core shielded cable of
length smaller than 15 m. If the
Attention
Top view
cable length exceeds 15 m, or if the
shielding of the cable is inadequate,
the operation may be unsatisfactory.
L
87.5
175
Screen
• Do not place or use one projector on
top of another projection unit.
Attention
• Leave a clearance of at least 50 cm so
that the ventilation opening on the rear
panel will not be blocked.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection distance by projection lens
Listed in the table below are the lens projection distances for the PT-D5600E (lens included), PT-D5600EL (lens
sold separately), PT-DW5000E (lens included) and PT-DW5000EL (lens sold separately).
• PT-D5600E, PT-D5600EL
Screen aspect ratio 4:3
Unit : m, (SD : inch)
Optional lens
Wide-angle Intermediatefocus Long-focus Ultra-long-focus
Standard
zoom lens
Wide-angle
fixed-focus
lens
zoom lens
Model No. : Model No. :
ET-DLE050 ET-DLE100
zoom lens
Model No. :
ET-DLE200
(2.5 - 4.0)
zoom lens
Model No. :
ET-DLE300
(3.7 - 5.7)
zoom lens
Model No. :
ET-DLE400
(5.7 - 8.0)
Projected screen size
(4:3 aspect ratio)
Height
position
: H
(1.8–2.5)
(1.33 - 1.78)
Diagonal
length
(SD)
Height Width
(SH) (SW)
(0.8)
(L)
Minimum Maximum
Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum
(LW)
1.79
2.16
2.53
2.90
3.27
3.64
4.38
5.49
7.34
(LT)
(LW)
1.33
1.61
1.89
2.16
2.44
2.71
3.27
4.09
5.47
6.85
(LT)
1.81
2.18
2.56
2.93
3.30
3.67
4.42
5.53
(LW)
2.45
2.96
3.46
3.97
4.47
4.97
5.98
(LT)
(LW)
3.84
4.63
5.43
6.22
(LT)
6.03
7.26
8.49
9.73
(LW)
5.90
7.08
(LT)
50
60
0.76
0.91
1.07
1.22
1.37
1.52
1.83
2.29
3.05
3.81
4.57
5.33
6.10
1.02
1.22
1.42
1.63
1.83
2.03
2.44
3.05
4.06
5.08
2.38 0.79
2.86 0.96
3.35 1.13
3.84 1.29
4.33 1.46
4.82 1.62
5.79 1.96
7.26 2.45
9.70 3.28
4.04
8.30 0 - 0.38
9.94 0 - 0.46
4.87
5.69
6.52
7.34
8.16
9.81
70
8.26 11.59 0 - 0.53
9.43 13.23 0 - 0.61
80
90
7.02 10.96 10.61 14.88 0 - 0.69
7.81 12.19 11.78 16.53 0 - 0.76
9.40 14.65 14.14 19.82 0 - 0.91
100
120
150
200
250
300
350
400
500
600
7.49 12.28 11.79 18.35 17.66 24.76 0 - 1.14
7.39 10.01 16.40 15.76 24.51 23.54 32.99 0 - 1.52
9.25 12.53 20.52 19.74 30.67 29.42 41.22 0 - 1.91
9.19 12.14
—
—
—
—
—
—
6.10 11.04 14.58
7.11 12.89 17.02
8.13 14.74 19.46
8.23 11.11 15.05 24.64 23.71 36.83 35.30 49.45 0 - 2.29
9.61 12.97 17.57 28.76 27.69 42.99 41.18 57.68 0 - 2.67
10.99 14.83 20.09 32.88 31.66 49.15 47.06 65.91 0 - 3.05
13.75 18.55 25.13 41.12 39.61 61.47 58.82 82.37 0 - 3.81
16.51 22.27 30.17 49.36 47.56 73.79 70.58 98.83 0 - 4.57
7.62 10.16 18.44 24.34
9.14 12.19 22.14 29.22
Screen aspect ratio 16:9
Unit : m, (SD : inch)
Optional lens
Wide-angle Intermediatefocus Long-focus Ultra-long-focus
Standard
zoom lens
Wide-angle
fixed-focus
lens
Model No. : Model No. :
ET-DLE050 ET-DLE100
zoom lens
zoom lens
Model No. :
ET-DLE200
(2.5 - 4.0)
zoom lens
Model No. :
ET-DLE300
(3.7 - 5.7)
zoom lens
Model No. :
ET-DLE400
(5.7 - 8.0)
Projected screen size
(16:9 aspect ratio)
Height
position
: H
(1.8–2.5)
(1.33 - 1.78)
Diagonal
Height Width
(SH) (SW)
(0.8)
(L)
Minimum Maximum
Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum
length
(SD)
(LW)
1.95
2.35
2.76
3.16
3.56
3.97
4.77
5.98
(LT)
(LW)
1.46
1.76
2.06
2.36
2.66
2.96
3.57
4.47
5.97
(LT)
1.98
2.38
2.79
3.19
3.60
4.00
4.81
6.03
(LW)
2.68
3.23
3.78
4.33
4.88
5.42
(LT)
4.41
5.31
6.21
7.11
8.01
8.90
(LW)
4.19
5.06
5.92
(LT)
6.58
7.92
9.26
(LW)
(LT)
50
60
0.62
0.75
0.87
1.00
1.12
1.25
1.49
1.87
2.49
3.11
3.74
4.36
4.98
1.11
1.33
1.55
1.77
1.99
2.21
2.66
3.32
4.43
2.60 0.87
3.13 1.05
3.66 1.23
4.19 1.41
4.72 1.59
5.26 1.77
6.32 2.14
7.92 2.68
6.43
9.03 0 - 0.38
7.71 10.82 0 - 0.46
8.99 12.62 0 - 0.53
70
80
6.79 10.61 10.27 14.41 0 - 0.61
7.66 11.95 11.55 16.20 0 - 0.69
8.52 13.29 12.83 18.00 0 - 0.76
90
100
120
150
200
250
300
350
400
500
600
6.52 10.70 10.25 15.97 15.40 21.58 0 - 0.91
8.17 13.39 12.85 20.00 19.24 26.96 0 - 1.14
8.00 10.58 3.58
8.05 10.91 17.88 17.18 26.71 25.64 35.93 0 - 1.52
5.53 10.01 13.24
6.64 12.03 15.90
7.75 14.04 18.56
8.86 16.06 21.22
—
—
—
—
—
—
7.48 10.08 13.66 22.37 21.51 33.42 32.05 44.89 0 - 1.91
8.98 12.10 16.40 26.86 25.84 40.13 38.45 53.86 0 - 2.29
10.49 14.13 19.15 31.35 30.17 46.84 44.86 62.82 0 - 2.67
11.99 16.15 21.89 35.84 34.50 53.55 51.26 71.79 0 - 3.05
15.00 20.20 27.38 44.82 43.16 66.97 64.07 89.72 0 - 3.81
18.01 24.25 32.87 53.80 51.82 80.39 76.88 107.65 0 - 4.57
6.23 11.07 20.09 26.54
7.47 13.28 24.12 31.86
The height position (H) of the ET-DLE050 is SH/2.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
• PT-DW5000E, PT-DW5000EL
Screen aspect ratio 16:9
Unit : m, (SD : inch)
Optional lens
Wide-angle Intermediatefocus Long-focus Ultra-long-focus
Standard
zoom lens
Wide-angle
fixed-focus
lens
zoom lens
Model No. : Model No. :
ET-DLE050 ET-DLE100
zoom lens
Model No. :
ET-DLE200
(2.5 - 4.0)
zoom lens
Model No. :
ET-DLE310
(3.4 - 4.5)
zoom lens
Model No. :
ET-DLE410
(4.5 - 8.4)
Projected screen size
(16:9 aspect ratio)
(1.8–2.5)
Height
position
: H
(1.33 - 1.78)
Diagonal
Height Width
(SH) (SW)
(0.8)
(L)
Minimum Maximum
Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum
length
(SD)
(LW)
1.98
2.39
2.80
3.21
3.62
4.03
4.84
6.07
(LT)
(LW)
1.48
1.78
2.09
2.39
2.70
3.00
3.61
4.53
6.05
(LT)
2.01
2.42
2.83
3.24
3.65
4.06
4.88
6.12
(LW)
2.71
3.27
3.83
4.38
4.94
5.49
(LT)
4.47
5.38
6.29
7.20
8.11
9.02
(LW)
3.89
4.69
5.49
6.29
7.08
(LT)
5.11
6.15
7.20
8.24
9.28
(LW)
(LT)
50 0.62
60 0.75
1.11
1.33
1.55
1.77
1.99
2.21
2.66
3.32
4.43
2.63 0.88
3.17 1.06
3.71 1.24
4.25 1.43
4.79 1.61
5.33 1.79
6.40 2.16
8.02 2.71
5.17
9.78 0 - 0.38
6.23 11.76 0 - 0.46
7.29 13.75 0 - 0.53
8.35 15.73 0 - 0.61
9.41 17.71 0 - 0.69
70 0.87
80 1.00
90 1.12
100 1.25
120 1.49
150 1.87
200 2.49
250 3.11
300 3.74
350 4.36
400 4.98
7.88 10.32 10.47 19.69 0 - 0.76
9.48 12.41 12.59 23.66 0 - 0.91
6.61 10.84
8.27 13.57 11.88 15.54 15.78 29.61 0 - 1.14
8.12 10.72 3.62
8.17 11.05 18.12 15.87 20.75 21.08 39.52 0 - 1.52
5.53 10.16 13.41
6.64 12.21 16.11
7.75 14.25 18.80
8.86 16.30 21.50
—
—
—
—
—
—
7.58 10.23 13.83 22.67 19.87 25.97 26.39 49.44 0 - 1.91
9.10 12.28 16.61 27.22 23.86 31.18 31.69 59.35 0 - 2.29
10.63 14.34 19.39 31.77 27.86 36.40 37.00 69.27 0 - 2.67
12.15 16.39 22.17 36.32 31.85 41.61 42.30 79.18 0 - 3.05
15.20 20.50 27.73 45.42 39.84 52.04 52.91 99.01 0 - 3.81
18.25 24.61 33.29 54.52 47.83 62.47 63.52 118.84 0 - 4.57
500 6.23 11.07 20.39 26.89
600 7.47 13.28 24.48 32.28
The height position (H) of the ET-DLE050 is SH/2.
Note • Black bands will appear at the top and bottom of the screen.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Calculation formulas for projection distance by lens types
• PT-D5600E, PT-D5600EL
Screen aspect ratio 4:3
(L, LW, LT : m SD : inch)
Standard
zoom lens
Minimum (LW)
Maximum (LT)
L=0.0370 x SD-0.0650
L=0.0488 x SD-0.0638
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Model No. :
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE300
Model No. :
ET-DLE400
L=0.0166 x SD-0.0361
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
L=0.0276 x SD-0.0452
L=0.0372 x SD-0.0478
L=0.0504 x SD-0.0657
L=0.0824 x SD-0.0758
L=0.0795 x SD-0.1380
L=0.1232 x SD-0.1310
L=0.1176 x SD+0.0244
L=0.1646 x SD+0.0651
Ultra-long-focus
zoom lens
Screen aspect ratio 16:9
(L, LW, LT : m SD : inch)
Standard
zoom lens
Minimum (LW)
Maximum (LT)
L=0.0403 x SD-0.0650
L=0.0532 x SD-0.0638
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Model No. :
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE300
Model No. :
ET-DLE400
L=0.0181 x SD-0.0361
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
L=0.0301 x SD-0.0452
L=0.0405 x SD-0.0478
L=0.0549 x SD-0.0657
L=0.0898 x SD-0.0758
L=0.0866 x SD-0.1380
L=0.1342 x SD-0.1310
L=0.1281 x SD+0.0244
L=0.1793 x SD+0.0651
Ultra-long-focus
zoom lens
• PT-DW5000E, PT-DW5000EL
Screen aspect 16:9
(L, LW, LT : m SD : inch)
Standard
zoom lens
Minimum (LW)
Maximum (LT)
L=0.0409 x SD-0.0650
L=0.0539 x SD-0.0638
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Ultra-long-focus
zoom lens
Model No. :
L=0.0183 x SD-0.0361
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE310
Model No. :
ET-DLE410
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
L=0.0305 x SD-0.0452
L=0.0411 x SD-0.0478
L=0.0556 x SD-0.0657
L=0.0910 x SD-0.0758
L=0.0799 x SD-0.1062
L=0.1043 x SD-0.1056
L=0.1061 x SD-0.1374
L=0.1983 x SD-0.1352
• The dimensions in the table in pages 17-18 and the values obtained from the above formulas may
contain slight errors.
Note
• When an SXGA signal is input and projected, the right and left ends of the picture will be blanked
and the aspect ratio will be 5:4.
• The brightness is different between the wide lens position settings and telephoto lens position
settings.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Setup precautions
• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual
supplied with the equipment once again.
• All cable connections should be made with the entire system devices, including the projector, first turned off.
• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect
cables.
• Video signals containing too much jitter may cause the images on the screen to randomly wobble or shake.
Inserting a time base corrector (TBC) in the projector’s video line will relieve this problem.
• The projector only accepts composite-video, S-video, analogue-RGB (with TTL sync. level), and digital signal.
• Some PC models are not compatible with PT-D5600E/PT-D5600EL/PT-DW5000E/PT-DW5000EL projectors.
• The pin assignments on the S-VIDEO IN terminal are
as follows:
• The pin assignments on the DVI-D input terminal
are as follows (interface with DVI-D output
terminal on PC):
Pin No.
Signal
Ground (luminance)
Ground (colour)
Luminance signal
Colour signal
Viewed from mating side
Viewed from mating side
Pin No.
Signal
T. M. D. S data 2-
T. M. D. S data 2+
T. M. D. S data 2
shield
Pin No.
Signal
+5 V
Ground
• The pin assignments on the RGB2 input terminal are
as follows:
Hot plug sense
T. M. D. S data 0-
T. M. D. S data 0+
T. M. D. S data 0
shield
Pin No.
Signal
DDC clock
DDC data
R/PR
G/G · SYNC/Y
B/PB
T. M. D. S data 1-
T. M. D. S data 1+
T. M. D. S data 1
shield
HD/SYNC
VD
T. M. D. S clock
shield
Viewed from mating side
T. M. D. S clock+
T. M. D. S clock-
Pin
Pins
: Not used.
and
• The DVI-D input terminal supports single link only.
• EDID settings should be performed to suit the DVI
equipment being connected. (Page 33)
-
,
: Ground.
• The DVI-D input terminal can be used to connect to a
DVI equipment, but note that images may not appear
or the projector may not work properly when
connected to certain DVI equipment.
• This projector supports HDCP.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of connecting with AV products
DVD player
Digital Hi-vision video deck
with DVI/HDMI terminal
DVD player
Video deck
DVI-D Cable or HDMI-DVI
conversion cable
(available in the market)
R/PR
G/Y
B/PB
SYNC/HD
VD
S-VIDEO IN
IN
RGB
OUT
2
IN
DVI-D IN
LAN
VIDEO IN
RGB
REMOTE
1
IN
REMOTE
1
2
IN
SERIAL
Control PC
OUT
D-SUB 9-pin straight cable
Digital Hi-vision video deck
Red (Connect PR
Blue (Connect PB
Green(Connect Y)
)
)
• When connecting with a video deck, be sure to use the one with a built-in time base corrector
(TBC) or use a TBC between the projector and the video deck.
Attention
• If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect
a TBC between the projector and the video deck.
• The EDID settings suited to the equipment connected must be performed when DVI-D signals are
input. (Refer to page 33.)
Example of connecting with PCs
PC with
DVI-D terminal
PC
PC
Control PC
DVI-D Cable (available in the market)
R/PR
G/Y
B/PB
SYNC/HD
VD
R/PR
G/Y
B/PB
SYNC/HD
VD
S-VIDEO IN
IN
RGB
OUT
2
IN
DVI-D IN
LAN
S-VIDEO IN
RGB
OUT
2
IN
DVI-D IN
LAN
VIDEO IN
RGB
REMOTE
1
IN
VIDEO IN
RGB
REMOTE
1
IN
REMOTE
1
2
IN
SERIAL
REMOTE
1
2
IN
SERIAL
OUT
IN
OUT
• For the specifications of the RGB signals that can be applied from the PC, see the data sheet on
page 58.
Note
• If your PC has the resume feature (last memory), the computer may not function properly until the
resume capability is disabled.
• When the SYNC ON GREEN signal is input, do not input sync signals to the SYNC/HD and VD
terminals. Doing so may disrupt the images since, rather than using synchronization initiated by
the GREEN signal, the sync signals of the SYNC/HD and VD terminals will be used instead. Even
if the images are not disrupted, the white balance may be lost. If this is the case, select “USER” as
the “COLOR TEMP.” setting (see page 28), and adjust “W-BAL LOW”.
• The white balance may be lost when the SYNC ON RGB signal is input. If this is the case, select
“USER” as the “COLOR TEMP.” setting (see page 28), and adjust “W-BAL LOW”.
• The EDID settings suited to the equipment connected must be performed when DVI-D signals are
input. (Refer to page 33.)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection
R/PR
G/Y
B/PB
SYNC/HD
VD
VIDEO IN
S-VIDEO IN
REMOTE
RGB
REMOTE
1
IN
1
2
IN
SE
IN
OUT
Press the LENS button three times to
adjust the lens shift. (Refer to page 24.)
Powering up the projector
When using an optional lens, install a projection
lens before powering up the projector. (Refer to
page 24.)
Press the AUTO SETUP button if the
input signal is RGB/DVI signal. (Refer to
page 25.) [on the main unit or the
remote control]
Remove the lens cover beforehand.
Connect the supplied power cable.
(220-240 V AC, 50 Hz/60 Hz)
Fit the image size to the screen size.
Press the LENS button twice and adjust the zoom
of the lens on the lens zoom adjustment menu.
Press the “ I ” marked side of the MAIN
POWER switch to turn on the power.
The power indicator lights up red, and the projector is
placed in the standby mode.
Press the LENS button and adjust the
focus of the lens on the lens focus
adjustment menu.
Press the “ I ” button. [on the main unit
or the remote control]
The power indicator illuminates in green and soon
the image is projected on the screen.
Display the zoom adjustment menu
again and adjust the zoom of the lens to
fit the image size to the screen size.
(Refer to page 24.)
Making adjustment and
selection
Roughly adjust the focus of the lens.
(Refer to page 24.)
Press the LENS button on the main unit or the
remote control unit to display a focus adjustment
• If the projector is powered up at about 0 ˚C,
a warm-up period of approximately five
minutes may be necessary to start
projection.
The temperature monitor (TEMP) lights
during the warm-up period.
Note
screen. Pressing
image into focus.
buttons to adjust the
When the warm-up is completed, the
temperature monitor (TEMP) turns off and
the image is projected on the screen.
• If the surrounding temperature is very low
and the warm-up period exceeds five
minutes, the control determines it as an
abnormal condition and turns off the
power automatically. If this happens, raise
the surrounding temperature to 0 °C or
higher and then turn the main power “on”
and turn the power “on” ( | ).
Select and set the projection scheme.
(Refer to page 34.)
Select the input signal by pressing the
input selector button to toggle through
RGB1, RGB2, VIDEO, S-VIDEO and DVI.
[on the main unit or the remote control]
Turn the feet, and adjust the tilt of the
main unit in the front and rear or left
and right.
• It is recommended that the projector be
allowed to warm up for at least 30 minutes
before any adjustments are made to the
focus.
Use the lens left/right adjustment dial to
adjust the direction of the lens. (page 24)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering off the projector
Direct power off function
The power supplied internally causes the cooling
fan to continue operating and cool off in the event
that the power has failed or even after the power
cord is accidentally disconnected immediately after
the power has been turned off.
Press the POWER OFF “ ” button.
Select “OK” with
or
button and
press the ENTER button.
(or press the POWER OFF “ ” button
again.)
• When the lamp has been cooled by the
direct power OFF function, it sometimes
takes longer than usual for the lamp to
light up again.
Note
The projection of the image stops, and the power
indicator of the main unit lights up orange. (The
cooling fan keeps running.)
• While the cooling fan is operating, do not
place the projector inside a box or bag.
• The operation time of the cooling fan will
be less if fewer than 4 minutes have
elapsed since the power was turned on.
Wait until the power indicator of the
main unit turns to red (i.e., until the
cooling fan stops).
Press the “ ” marked side of the MAIN
POWER switch to remove all power
from the projector.
• Do not turn the power supply off and
then immediately back on again.
Turning on the power supply will not light
up the light source lamp if the lamp is in
the process of cooling down after turning
off the power supply. To light up the lamp,
turn on the power supply again when the
lamp has been cooled sufficiently.
Turning on the power supply with the lamp
in the hot condition may shorten the lamp
life.
Attention
• The projector consumes approximately 15
watts of power even in standby mode after
the cooling fan stops. (Power indicator lit
in red)
Note
• If you re-power the projector after shutting
off the main power inadvertently, the
projection lamp may remain unlit. Please
turn the power on again after a while.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
How to install and remove the How to adjust the lens
projection lens (optional)
How to adjust the lens
focus, lens zoom and lens
How to install the
up/down position
projection lens
movement (optical shift)
Align the guide of the projection lens
The focus, zoom and up/down position of the
with the guide groove in the main unit.
images projected on the screen can be adjusted
Turn the lens clockwise until it clicks
into place.
while the projector is positioned appropriately in
relation to the screen.
Press the LENS button on the remote control
or on the control panel of the main unit.
Guide
Guide groove
Pressing the button changes the setup screen
in the order of “LENS FOCUS”, “LENS ZOOM”
and “LENS SHIFT”.
Choose an item and adjust it using
buttons.
Caution
Be careful not to catch your fingers between the
lens and shroud when shifting the lens.
Guide groove
Lens signal contact
Guide
Projection lens
• Turn the lens counterclockwise and
confirm that the lens does not come
off.
Attention
Note
• When a lens without zoom functions is used, the
lens zoom adjustment menu will still displayed,
but no operations can be performed using the
items on this menu.
• By shifting the lens up/down position, it is possible
to make adjustments upward or downward from
the standard position in the direction of the upper
50 % of the projected screen height.
How to remove the
projection lens
Turn the lens counterclockwise as
far as it will go.
•
Operations can be performed faster by holding down
the buttons for about 3 or more seconds.
While holding down the lens lock
button, turn the lens further
counterclockwise.
How to adjust the lens
position to the left or right
Remove the lens.
When the lens left/right adjustment dial is turned
clockwise, the screen moves toward the left;
conversely, when it is turned counterclockwise, it
moves toward the right. The maximum travel
distance toward the left or right is 10 % of the
projection screen width.
The screen
moves toward
the right
The screen
moves toward
the left
Lens lock button
• Before replacing the lens, turn off the
projector’s power.
• Do not touch the lens signal contact.
Dust or dirt may cause defective
contact.
• Do not touch the surface of the
projection lens with your bare hands.
• Store the replaced lens where it will
be free from vibration and impact.
Note
Lens left/right
adjustment dial
Maximum
adjustment
position
• Move the lens left/right adjustment dial
to any position up to the maximum
adjustment position to make the
Attention
adjustment. Turning the dial with undue
force may cause malfunctioning.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic adjustment (AUTO SETUP)
Automatic adjustment function adjust the resolution, clock phase and image position automatically when dots-
structured analogue RGB signals such as computer signal are supplied. (Automatic adjustment is not available if
moving picture input signals or signals having a dot clock frequency of more than 108 MHz are supplied.) When
DVI signals are input, the image position is adjusted automatically.
It is recommended to supply images with a bright white frame at the outermost periphery containing characters etc.
that are clear in white and black contrast when the system is in automatic adjustment mode. Avoid supplying
images that involve halftones or gradation such as photographs and computer graphics.
• “CLOCK PHASE” may have been shifted even when the adjustment ended normally.
In this case, manually adjust the “CLOCK PHASE”.
Note
• Automatic adjustments cannot be performed when images with blurred edges or dark images are input.
With Composite sync and G-SYNC sync signals and some types of PCs, it may not be possible to
perform these automatic adjustments.
In this case, manually adjust the items of “INPUT RESOLUTION”, “CLOCK PHASE” and “POSITION”.
• Image may be disturbed for about 4 seconds during automatic adjustment, which is not an abnormal
error.
Using the FREEZE function
The image on the screen displayed when you press the FREEZE button on the remote control is displayed as a still
image until you press the FREEZE button again.
Using the SHUTTER function
If the projector is not going to be used for a certain period of time such as while a meeting is on a break or
preparations are being made, the mechanical shutter can be used to hide the images temporarily.
Press the “SHUTTER” button of the remote control or the main unit.
The image is turned off.
Press the “SHUTTER” button again.
The image comes back.
Using the digital zoom (– D.ZOOM +) function
A portion of the picture on the screen can be zoomed in with “– D.ZOOM +” buttons of the remote control. It is
useful for highlighting a specific object during the presentation.
Press the “– D.ZOOM +” button of the remote control.
Product
1999
2000
%
The image is zoomed in.
A
B
C
D
110
%
110
131
64
122
106
76
E
18
5%
81
%
%
%
%
Change the magnification with the “– D.ZOOM +”
button.
D
A
47 13%
119
112
69
122
C
32%
76
42
47
29%
21%
The magnification can be adjusted from 1.0 to 3.0 times.
E
26
18
-1
B
106
ADJ
-
5
Use
buttons to move the magnified
TOTAL
100%
368
368
image.
To restore the original image, press the “MENU”
button.
B
C
D
131
64
• The digital zoomed state cannot be stored in memory.
Note
2
• If the input signal format is changed while in digital
zoom mode, the projector will exit digital zoom
function.
32%
42
• The combined magnification of “POSITION” zoom and
digital zoom is 9.99 times maximum.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen menus
Structure of menu screens
Menus are extensively used for configuring, adjusting or reconfiguring the projector.
The menus structure is as follows:
MENU
MENU
PICTURE
POSITION
PICTURE (page 29)
For RGB signals
For DVI signals
ADVANCED MENU
LANGUAGE
OPTION1
PICTURE
PICTURE
PICTURE MODE
BRIGHT
GRAPHIC
32
32
DEFAULT
10
06
PICTURE MODE
BRIGHT
GRAPHIC
32
32
DEFAULT
10
06
OPTI0N2
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
TEST PATTERN
SECURITY
NETWORK
OFF
ON
OFF
ON
SELECT
ENTER
EXIT
AI
AI
SYSTEM
RGB
SELECT
ADJ
RETRN
NETWORK
(page 38)
SELECT
ADJ
RETRN
For S-Video/Video signals
For YPBPR signals
NETWORK
PICTURE
PICTURE
HOST NAME
DHCP
PICTURE MODE
BRIGHT
CONTRAST
COLOR
STANDARD
PICTURE MODE
BRIGHT
CONTRAST
COLOR
STANDARD
32
32
32
OFF
32
32
32
32
IP ADDRESS
SUBNET MASK
GATEWAY
MAC ADDRESS
STORE
TINT
TINT
32
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
DEFAULT
05
DEFAULT
05
06
ON
ON
SELECT
ENTER
RETRN
06
ON
ON
AUTO1
SECURITY (page 37)
AI
AI
TV-SYSTEM
SYSTEM
AUTO
SELECT
ADJ
RETRN
SELECT
ADJ
RETRN
TEST PATTERN
(page 37)
POSITION (page 30)
POSITION
POSITION
ASPECT
ZOOM
CLOCK PHASE
KEYSTONE
ADVANCED MENU
(page 32)
OPTION2 (page 35)
4
:
3
OPTION2
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
ID
ALL
FRONT
DESK
DUAL
HIGH
16
FRONT/REAR
DESK/CEILING
LAMP SELECT
LAMP POWER
RS232C
INPUT RESOLUTION
SELECT
ENTER
RETRN
CLAMP POS.
RASTER POSITION
XGA MODE
1
XGA
SYSTEM INFORMATION
FAN CONTROL1
FAN CONTROL2
FUNC1
SXGA MODE
SXGA
NORMAL
HORIZ.
SELSCT
ENTER
RETRN
DISABLE
AUTO POW. OFF
PASSWORD
LANGUAGE (page 33)
SELECT
ADJ
RETRN
LANGUAGE
ENGLISH
OPTION1 (page 34)
OPTION1
COLOR CORRECTION
CONTRAST MODE
AUTO SIGNAL
BACK COLOR
SUB MEMORY LIST
DVI EDID
OFF
BLACK
EDID2:PC
SELECT
ENTER
RETRN
SELECT
ENTER
RETRN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic menu operations
Returning to the previous
page
Press the “MENU” button.
• Pressing the “MENU” button returns the screen to
The MENU appears on the screen.
the previous menu page.
MENU
PICTURE
POSITION
•
When the MENU is on the screen, pressing the
“MENU” button clears all menus from the screen.
ADVANCED MENU
LANGUAGE
OPTION1
Menu items shown in
transparent characters
OPTI0N2
• Some menu items may not be valid for certain
signal formats applied to the projector.
TEST PATTERN
SECURITY
NETWORK
The menu items that cannot be adjusted or used are
shown in transparent characters, and they cannot be
selected even by pressing the ENTER button.
SELECT
ENTER
EXIT
Menu items setting
• The bottom prompt line differs on each menu
Select (highlight) the desired item with
the or buttons.
Selected items are displayed in blue.
depending on the selected menu option:
• A prompt “
the setting.
• A prompt “
bar graph.
ADJ” appears when changing
MENU
PICTURE
POSITION
ENTER” appears for a separate
ADVANCED MENU
LANGUAGE
OPTION1
Resetting to the factory
default
OPTI0N2
TEST PATTERN
SECURITY
NETWORK
STD (standard) button is used to reset all of the
projector adjustment values to the default levels
which were set at the time of shipment from the
factory.
SELECT
ENTER
EXIT
PICTURE
Press the “ENTER” button to enter your
selection.
The submenu for the selected option will now open.
(e.g. : PICTURE Menu)
PICTURE MODE
BRIGHT
GRAPHIC
32
32
DEFAULT
10
06
OFF
ON
RGB
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
PICTURE
PICTURE MODE
BRIGHT
GRAPHIC
32
AI
SYSTEM
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
32
SELECT
ADJ
RETRN
DEFAULT
10
06
• If the parameter value on a bar graph is reset to
the factory default, the bar turns to white.
OFF
ON
AI
SYSTEM
RGB
•
The upper and lower triangular markings on
a bar graph indicate the default setting for the
parameter. If no such triangular markings are
shown on the bar graph, the parameter
cannot be reset to the factory default.
Note
SELECT
ADJ
RETRN
Highlight the desired adjustment item
with the or buttons, then change
the parameter value with the
buttons.
(Example of separate adjustment screen)
or
Indicates the current
parameter value.
Indicates the
factory default.
• If no button is operated for approx. 5 seconds
while a bar graph is displayed, the screen will
return to the previous page.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
• For RGB signals
• For DVI signals
COLOR
PICTURE
PICTURE
(For S-Video/Video/YPBPR signals only)
PICTURE MODE
BRIGHT
GRAPHIC
32
32
DEFAULT
10
06
OFF
ON
RGB
PICTURE MODE
BRIGHT
GRAPHIC
32
32
DEFAULT
10
06
: Deepens colours.
: Weakens colours.
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
CONTRAST
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
TINT
OFF
ON
AI
AI
(For S-Video/Video/YPBPR signals only)
“TINT” is used to adjust human skin.
SYSTEM
SELECT
ADJ
RETRN
SELECT
ADJ
RETRN
: Adjusts skin tone toward greenish colour.
: Adjusts skin tone toward reddish-purple.
•
For S-Video/Video signals
•
For YPBPR signals
PICTURE
PICTURE
PICTURE MODE
BRIGHT
CONTRAST
COLOR
STANDARD
32
32
32
PICTURE MODE
BRIGHT
CONTRAST
COLOR
STANDARD
32
32
32
COLOR TEMP.
The colour temperature is adjusted when the white
areas of images take on a reddish or bluish hue.
DEFAULT: Standard setting
TINT
32
TINT
32
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
COLOR TEMP.
WHITE GAIN
SHARPNESS
NR
DEFAULT
05
06
ON
ON
DEFAULT
05
06
ON
ON
HIGH
: The white areas take on a more
bluish-white hue.
MIDDLE : The white areas take on a slightly
reddish hue.
AI
AI
USER
: The RGB values of the white balance
are set separately.
TV-SYSTEM
SYSTEM
AUTO1
AUTO
SELECT
ADJ
RETRN
SELECT
ADJ
RETRN
Press the ENTER button, select “W-
BAL HIGH” or “W-BAL LOW”, and
proceed with the detailed settings.
: The colours of the selected
PICTURE MODE
item are darkened.
The picture mode can be selected from the
: The colours of the selected
item are lightened.
following depending on viewing conditions and the
video signal source in use:
DYNAMIC : Picture brightness/contrast ratio is
increased to suit brighter viewing
environments.
GRAPHIC : The picture becomes suitable for
input from to the personal
WHITE GAIN
The brightness of white parts of the image can be
adjusted.
computer.
: The intensity of white colour increases.
: Reverts to natural image.
STANDARD : The picture becomes suitable for
moving images in general.
CINEMA
: The picture becomes suitable for
movie sources.
SHARPNESS
NATURAL : The picture becomes suitable for
use in a dark room.
“SHARPNESS” is used to adjust the crispness of
the image.
: Sharpens the edge of the image.
: Softens the edge of the image.
BRIGHT
“BRIGHT” is used to adjust the black level
(brightness).
: Raises the picture brightness.
: Lowers the picture brightness.
NR
In this mode, the video noise is reduced.
(For S-Video/Video/YPBPR signals)
OFF : No correction
CONTRAST
ON : Noise reduction is set to ON.
(For RGB/DVI signals)
“CONTRAST” is used to adjust the contrast ratio.
: Raises the contrast ratio.
OFF : No correction
1
2
3
: Low
: Middle
: High
: Lowers the contrast ratio.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the position
POSITION
POSITION
ASPECT
ZOOM
CLOCK PHASE
KEYSTONE
AI
Gray scale control is exercised to suit the images,
and optimal images with a clear contrast are
projected.
4
:
3
16
ON : AI compensation is enabled.
OFF : AI compensation is disabled.
SELECT
ENTER
RETRN
TV-SYSTEM
POSITION
(For S-Video/Video signals)
The position where the images are displayed can
be moved here.
The setting that corresponds to the TV system is
selected here.
: The position is moved horizontally.
AUTO1 : Standard setting
: The position is moved vertically.
Automatically selects the TV standard
that matches the input video signal, out
of NTSC, PAL, NTSC4.43, SECAM and
PAL60.
ASPECT
AUTO : (For S-Video/Video signals only)
At this setting, when S1 video signals
are identified as being input to the S-
AUTO2 : Automatically selects the TV standard
that matches the input video signal, out
of NTSC, PAL-M, and PAL-N.
• Normally “AUTO1” or “AUTO2” should be
chosen for this option.
1
Video connector or video ID signals are
identified as being input to the video
connector, the images are displayed
after automatically being converted to
the 16:9 aspect ratio.
• If the video signals are not displayed properly
due to signal deterioration, choose the TV
system that matches the input video signals.
Automatically selected by detecting the
horizontal/vertical scan frequencies and colour sub-
carrier listed in the table below:
2
16:9 : At this setting, when standard signals
are input, the images are converted to
the 16:9 aspect ratio and displayed.
When wide-screen signals 3 are input,
the images are displayed with their
inherent aspect ratio intact.
H. Scan
V. Scan
Colour
Subcarrier
(MHz)
Signal
Frequency Frequency
2
4:3
: At this setting, when standard signals
System
(kHz)
15.75
15.75
15.63
15.75
15.63
15.63
15.75
(Hz)
are input, the images are displayed with
their inherent aspect ratio intact. When
wide-screen signals 3 are input, they are
converted by the PT-D5600E to the 4:3
aspect ratio and displayed. With the PT-
DW5000E, the images are reduced in
size and displayed without converting
their aspect ratio so that they will fit onto
a screen with a 4:3 aspect ratio.
NTSC
NTSC4.43
PAL
60.00
60.00
50.00
60.00
50.00
50.00
60.00
3.58
4.43
PAL-M
PAL-N
3.58
SECAM
PLA60
4.25 or 4.41
4.43
S4:3 : Select this setting when using a 16:9
screen.
HV FIT : At this setting, the images are displayed
to fill the entire screen.
SYSTEM
(For RGB/YPBPR signals)
If the aspect ratios of the input signals
and screen differ, the images are
converted into the screen’s aspect ratio
(4:3 for the PT-D5600E or 15:9 for the
PT-DW5000E) and displayed.
This enables the RGB system or YPBPR system to
be selected.
For the signals which are supported, refer to page
58.
1 S1 video signals are 16:9 video signals to
which is added the detection signal output from
the video deck or other unit which supports the
wide-screen format.
2 Here, the standard signal means 4:3 or 5:4
input signals.
3 Here, the wide-screen signals means 16:9,
15:9 or 15:10 input signals.
(Continued on next page)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the position
• If you choose an aspect ratio that does
Attention
ZOOM
not match the source video’s aspect
ratio, you will see a picture with an
aspect ratio not the same as that of
the original picture. Choose the
appropriate aspect ratio carefully to
match that of the original picture.
This enables the enlargement ratio to be changed
and the resulting enlarged image displayed.
: The enlargement ratio in the horizontal
direction is changed.
: The enlargement ratio in the vertical
direction is changed.
• If the picture size is compressed or
enlarged by using the 16:9 aspect ratio
when the projector is used for
profitable purpose or in the presence
of an audience (for example, in a
coffee shop or at a hotel etc.), it may
infringe the rights of the copyright
owner of the original picture.
• If a picture with the standard (4:3)
aspect ratio is projected at a wide
aspect ratio, parts of the picture may
run over the screen bounds or the
overall picture may be distorted. To
view the picture at its original aspect
ratio, choose the standard 4:3 aspect
ratio.
Note
CLOCK PHASE
(For RGB/YPBPR signals only)
Clock phase adjustment allows the user to minimize
visible noise with the
or
button.
• When projecting signals whose dot
clock frequency is 108 MHz or higher,
the noise may not be disappear even
when the clock phase is adjusted.
• Clock phase adjustment is not
Note
available for digital RGB signals.
KEYSTONE
KEYSTONE : Keystone distortion can be corrected
only along either horizontal bound of
the picture.
button:
button:
•
Keystone distortion can be corrected to
30 ° of the angle of tilt for the projector.
However, the greater the correction
amount, the more the picture quality will
deteriorate, and the harder it will become
to achieve a good level of focus. To
obtain the best picture quality, set up the
projector and screen in such a way that
the amount of keystone correction
Note
required is as minimal as possible.
• The picture size will also change when
correction of keystone distortion is
carried out.
LINEARITY : After you are finished with keystone
adjustment, adjust vertical linearity
with the
or
button.
Linearity is not adjustable if no
correction was made to keystone
distortion.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use ADVANCED MENU
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
CLAMP POS.
INPUT RESOLUTION
Input resolution adjustment achieves the best
image when the screen flickers or halo is observed
around the contour.
1
RASTER POSITION
XGA MODE
SXGA MODE
: These select the items listed below.
XGA
SXGA
: These select the value.
“TOTAL DOTS”, “DISPLAY DOTS”, “TOTAL
LINES” and “DISPLAY LINES”
SELSCT
ENTER
RETRN
Each item automatically displays a value in
response to the type of the input signal. If vertical
stripes appear on the screen or the image is partly
missing, increase or decrease the displayed value
while observing the screen to achieve the optimal
value.
DIGITAL CINEMA REALITY
B
R
(Only for input of S-Video/ Video/ YP P [480i,
576i] signals.)
ON: Set at ON when you need to faithfully
capture images shot at 24 frames per
second as in movies.
• The abovementioned vertical stripes
will not appear on the screen when all
white signals are input.
Note
OFF: Set at OFF when unnatural images are
obtained in the ON status.
•
The picture may be distorted during the
adjusting operation, but this is not a fault.
• The input resolution can be adjusted
only when RGB signal input is applied
with RGB1 and RGB2 IN.
• Automatic adjustment is not available
if signals having a dot clock frequency
of more than 108 MHz are supplied.
BLANKING
You can perform fine adjustments for blanking if
noise appears at the ends of the screen or the
image protrudes out of the screen during image
projection using a video deck and so on.
: Select the UPPER, LOWER, LEFT or
RIGHT adjustment.
: Adjust the blanking width.
CLAMP POS.
B
R
(For RGB/ YP P signals only)
For upper adjustment
For lower adjustment
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
Adjust with the
buttons.
The value changes from 0 to 255.
The optimal value for the clamp position adjustment
• If dark areas are crushed:
The optimal value is the point where the dark
area is best improved.
For left adjustment
For right adjustment
• If the dark areas are displayed in green:
The optimal value is the point where the
green area becomes dark and clear.
• The clamp position can be adjusted
only when the RGB signal input is
applied with RGB1 and RGB2 IN.
Note
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the display language
How to use ADVANCED MENU
Currently chosen
language is displayed
here.
LANGUAGE
ENGLISH
RASTER POSITION
When the whole area where the input picture can
be displayed is not used, the picture can be moved
to any position inside the display area.
: These adjust the value in the horizontal
direction.
: These adjust the value in the vertical
direction.
SELECT
ENTER
RETRN
XGA MODE
Menus, setting items, adjustment screens, and
control button names will be displayed in the
language the user chooses.
The available languages are:
ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL,
This mode takes effect only when XGA (RGB)
signals are input.
XGA : Standard setting
WXGA : Select this mode when WXGA signals
are input.
ITALIANO,
,
,
,
.
• The projector’s on-screen display is
set to the English language by default.
Note
SXGA MODE
This mode takes effect only when SXGA (RGB)
signals are input.
SXGA : Standard setting
SXGA+: Select this when the screen is cut off.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION1 settings
OPTION1
COLOR CORRECTION
CONTRAST MODE
SUB MEMORY LIST
Multiple sets of image adjustment data (PICTURE,
POSITION, ADVANCED MENU adjustment values)
for the same kind of signal can be registered.
AUTO SIGNAL
BACK COLOR
SUB MEMORY LIST
DVI EDID
OFF
BLACK
SUB MEMORY LIST
— : RGB1–XGA60
EDID2:PC
SELECT
ENTER
RETRN
1
2
3
4
5
6
7
8
:
:
:
:
:
:
:
:
COLOR CORRECTION
OFF : Standard setting
USER : The six colours of red, green, blue, cyan,
magenta and yellow can be adjusted
and registered for each of four signal
systems: Video, S-Video, RGB and
YPBPR.
SELECT
STORE
Press the ENTER button to make the
detailed settings.
Registering in sub memory
Select the sub memory number to be registered
using the
buttons.
COLOR CORRECTION
RGB
The current signal
system is displayed.
Press the ENTER button.
R
G
B
Cy
Mg
Ye
0
0
0
0
0
0
• Sub memories range from 1 to 8.
Note
How to select sub memory
Select sub memory number (1 to 8) using the
buttons. Select “–” if you do not wish to
use the sub memory.
SELECT
ADJ
RETRN
Press the ENTER button.
CONTRAST MODE
There are two modes for adjusting to the operating
environment.
• You cannot select sub memory of a
different signal system.
Note
NORMAL : The contrast is set to normal and the
brightness to maximum.
How to erase sub memory
HIGH
: The contrast is set to maximum and
the brightness to normal.
Select sub memory number (1 to 8) corresponding
to sub memory to be erased using
buttons.
AUTO SIGNAL
Press the STD button.
The position where the screen is displayed can be
adjusted automatically without pressing the AUTO
SETUP button on the remote control each time
signals are input when signals are input frequently
such as when the projector is used at a conference.
ON : Auto setup is performed automatically
when the video signals of the images
When the indicator of sub memory to be erased
flashes, press the ENTER button.
DVI EDID
Set EDID to match the device connected.
being projected have changed.
OFF : The input auto setup function is set to
OFF.
Mode
Matching Signal
480p, 576p, 720/60p, 720/50p,
1080/60i, 1080/50i
EDID1
VGA60, SVGA60, XGA50, XGA60,
XGA70, XGA85, WXGA768/50,
WXGA768/60, SXGA60
BACK COLOR
EDID2:PC
You can set the colours of the screen when no
signal is input to the projector.
BLUE: Set screen colour to blue.
BLACK: Set screen colour to black.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION2 settings
OPTION2
LAMP SELECT
ID
ALL
FRONT
DESK
DUAL
HIGH
“LAMP SELECT” is used to choose from Single Lamp
and Dual Lamp modes depending on user’s needs or
viewing conditions. In Single Lamp mode, the
projector may automatically select either lamp from
the 2 lamps, or the particular lamp can be specified.
DUAL : Two lamps are used simultaneously.
SINGLE : One of either lamps is used (lamp with
shorter operating hours is
FRONT/REAR
DESK/CEILING
LAMP SELECT
LAMP POWER
RS232C
SYSTEM INFORMATION
FAN CONTROL1
FAN CONTROL2
FUNC1
NORMAL
HORIZ.
automatically selected).
DISABLE
AUTO POW. OFF
PASSWORD
LAMP1 : Lamp Unit 1 is always used.
LAMP2 : Lamp Unit 2 is always used.
When one of the above settings is selected, it will
take effect after ENTER is pressed.
SELECT
ADJ
RETRN
ID
• If, in the “SINGLE”, “LAMP1” or
“LAMP2” mode, one lamp remains off
or the currently active lamp exceeds
1 500 hours of cumulative operating
time (when “HIGH” is selected as the
lamp power setting), the other lamp
will light. If, in the “DUAL” mode, one
lamp remains off or the currently active
lamp exceeds 1 500 hours of
Note
The projector has an ID number setting function
that helps the user to control two or more projectors
either simultaneously or separately with a single
remote control. The ID number is set to “ALL” by
default. Hence the ID number need not be set
when only one projector is used.
1–64 : The ID number is set in this range.
cumulative operating time (when
“HIGH” is selected as the lamp power
setting), the other lamp alone will light.
However, if both lamps remain off or
the 1 500 hours of cumulative
operating time are exceeded, the
projector will enter the standby mode.
• If only one lamp is installed in the
projector, set lamp mode to either
“LAMP1” or “LAMP2”. “LAMP1” or
“LAMP2” is selected. If the
• The ID number can be set to “ALL”, or
selected from “1” to “64”.
Note
• If the projectors are given ID numbers,
their remote controls must be assigned
the same ID numbers, respectively.
• If the ID number of a projector is set to
“ALL”, it can be controlled by the
remote control or the PC with any ID
number.
If multiple projectors are used and
some of them have their IDs set to
“ALL”, they cannot be controlled
separately from the projectors with
other ID numbers.
corresponding lamp is not installed,
the other lamp will turn on.
The colours of the items indicate the status.
•
Green Current setting
Cyan
Now changing from one
status to another
For details on remote control ID
setting, see page 15.
Red
White
Lamp that has failed to light
Any other status
• If the projector is repeatedly used for
short periods of time, the lamps will
need to be replaced more frequently.
FRONT/REAR
“FRONT/REAR” is used to choose the appropriate
projection scheme from Front and Rear:
FRONT : Choose this option if pictures are
projected from the front of a reflective
screen.
This time period is 4 000 hours when
long life lamp units (page 42) are used.
LAMP POWER
REAR : Choose this if pictures are projected
from the back of a translucent screen.
The luminance of the projection lamp can be
changed depending on user’s needs or the viewing
conditions.
DESK/CEILING
HIGH : Set when high brightness is necessary.
LOW : Set when high brightness is not
necessary.
“DESK/CEILING” is used to choose the appropriate
projection scheme from Desk and Ceiling:
DESK
: Choose this option if the projector is
installed on a floor-standing base.
• When set to “LOW”, it is possible to
reduce power consumption, reduce
operating noise and extend lamp
service life.
• “LOW” is set automatically when long
life lamp units are used.
Note
CEILING : Choose if the projector is installed on
the ceiling using the optional ceiling
mount bracket.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232C
FAN CONTROL2
This sets the communication parameters at the
serial terminals.
The fan can be controlled in accordance with the
direction in which the images are to be projected.
For details on the serial terminals, refer to “Using
the serial terminals” (pages 38).
IN BAUDRATE : 9 600, 19 200 or 38 400 is
selected.
HORIZ.
: Standard setting
VERTICAL : This is selected when projecting
images at a significant angle toward
the vertical (more than 30 degrees
from the horizontal).
IN PARITY
: NONE, EVEN or ODD is
selected.
V
OUT BAUDRATE: 9 600, 19 200 or 38 400 is
selected.
H
30°
30°
30°
30°
H
OUT PARITY
VPS SYSTEM
GROUP
: NONE, EVEN or ODD is
selected.
: MASTER or SLAVE is
selected.
: A to Z is selected. MASTER
or SLAVE is also selected.
H: HORIZ.
V: VERTICAL
V
• Select the correct FAN CONTROL2
setting in accordance with the direction
in which the images are to be projected.
Using the projector at the wrong FAN
CONTROL2 setting will shorten the
service life of the lamps.
Attention
SYSTEM INFORMATION
The projector’s system information can be viewed.
SYSTEM INFORMATION
ROM VERSION
SET RUNTIME
LAMP1 LOW
HIGH
TOTAL
LAMP2 LOW
HIGH
1. 00. 00
300h
100h
200h
300h
100h
200h
300h
20
FUNC1
The user can set the function for the remote
control’s FUNC1 button.
LAMP POWER:
The button functions in the same way as
“LAMP POWER” of “OPTION2”.
ASPECT:
This button has the same functions as
“ASPECT” of “POSITION”.
SUB MEMORY LIST:
This button has the same functions as “SUB
MEMORY LIST” of “OPTION1.”
TOTAL
LAMP1 ON
LAMP2 ON
LAMP1 TYPE
LAMP2 TYPE
20
LAD55
LAD55
RETRN
FAN CONTROL1
The fan can be controlled in accordance with the
operating conditions.
AUTO POW.OFF
The projector can be automatically set to the
standby mode if no signals are input for the set
duration.
NORMAL : Standard setting
HIGHLAND : This is selected when using the
projector at an altitude of over
1 400 metres.
DISABLE:
Standard setting. This function is set to OFF.
45MIN.–90MIN.:
The duration can be set in 15-minute
increments from 45 to 90 minutes.
• The auto power OFF function does not
work while the freeze function is used.
Note
PASSWORD
This function is used by a service person.
Input the password with the numeric buttons (0 to
9) of the remote control and press ENTER button to
confirm the entry.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the internal test pattern Setting the security
The projector has eight types of internal test patterns
to check the condition of the set.
To display test patterns, follow the steps below.
The projector’s security function enables the password
input screen to be displayed or a company’s URL
address to be set and displayed underneath the
projected images.
• Results of adjustment on the image,
picture quality, position, size and other
factors will not be reflected in test
patterns. Be sure to display the input
signal before performing various kinds
of setting.
Note
PASSWORD
OK
RETURN
(When using the projector for the first time)
Press the and
,
,
,
,
,
,
buttons in this order, and press the ENTER button.
: Search through the various types of test
patterns
(When the password has been changed)
Input the new password, and press the ENTER button.
Cycle of displayed internal
test patterns
Setting the password
It is possible to display the password input screen
each time the power is turned on. If this option is
used, no operations except for the POWER button
can be performed without inputting the correct
password.
MENU screen
+
All white
Entry screen
ON : Password input is enabled.
OFF : Password input is disabled.
Changing the password
The password can be changed. Press the ENTER
button.
Focus
All black
Set the password using the
,
,
,
buttons (up to 8 buttons can be set).
Press the ENTER button.
Confirm the password by inputting it again.
Press the ENTER button.
(This completes the settings.)
Note • Asterisks ( ) will appear on the
screen in the place of the actual
Colour bars
Flag
password when the password is input.
•
If the wrong password is input, the letters
for “Password”, “New”, etc. appear in red.
Input the correct password.
Setting the text
The text which has been set can be displayed
underneath the projected images all the time.
ON : The text display is enabled.
Window (inversion)
16:9 frame
OFF : The text display is disabled.
Black on
white ground
Changing the text
The text which is to be displayed when ON has
been selected for the text setting can be changed.
Press the ENTER button.
Window
Select the text using the
,
,
,
buttons, and press the ENTER button. (Up to
22 alphanumerics can be input in succession.)
White on
black ground
Select “OK” using the
,
,
,
buttons, and press the ENTER button.
To cancel the change at any time, select CANCEL.
The PT-DW5000E and PT-DW5000EL support the
4:3 frame format.
•
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the network Connecting the PC
The settings required for the network must be
established in order to use the web browser (page 45)
functions that the PC uses to control the projector.
System requirements
The following system specifications are required in
order to use the networking functions.
NETWORK
• PC
HOST NAME
DHCP
OS
: Windows XP/2000/Me (Millennium
Edition)/98SE (Second Edition)
OFF
IP ADDRESS
SUBNET MASK
GATEWAY
MAC ADDRESS
STORE
CPU : Pentium
RAM : 64 MB or more (128 MB or more for
Windows XP/2000)
Web browser: Internet Explorer 6.0 or newer,
Netscape Communicator 7.0 or
newer
processor or faster
SELECT
ENTER
RETRN
HOST NAME
DHCP
: Make alteration if necessary
when to use the DHCP server.
: Set the DHCP item to ON when
to acquire an IP address
automatically using the DHCP
server.
• LAN cable
Type : Category 5 compatible straight cable
Length: 100 metres or less
• If you want to use the e-mail function,
make sure the system can handle e-
mail.
Attention
Set to OFF if DHCP server is not
used.
IP ADDRESS
: Enter the IP address if DHCP
server is not used.
SUBNET MASK : Enter the subnet mask if DHCP
server is not used.
Operation is not guaranteed for all
computers that meet the above
conditions.
GATEWAY
: Enter the gateway address if
DHCP server is not used.
MAC ADDRESS : Displays the MAC address
(Media Access Control Address),
which is proper to the network
device.
This function may be needed
when to use the DHCP server.
: The settings are stored in the
memory.
Connection example
STORE
Projector
• Before using the DHCP server, make
sure the DHCP server is already
functioning.
• For details of IP address, subnet
mask, and gateway, ask the network
administrator.
Attention
Personal
computer
R/PR
G/Y
B/PB
SYNC/HD
VD
S-VIDEO IN
IN
RGB
REMOTE
1
IN
RGB 2
OUT
IN
DVI-D IN
N
VIDEO IN
REMOTE
1
2
IN
SERIAL
OUT
10 BASE-T or 100 BASE-TX
LAN cable
(straight)
LAN cable
(straight)
Hub
• Touching the LAN terminal with your
hand (or body) when you are carrying
a static charge may damage the
equipment due to a discharge of static
electricity. Therefore, be careful not to
touch the LAN terminal or metal parts
of the LAN cable.
Attention
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the serial terminals
The main unit is equipped with SERIAL terminals located in its terminal section on the side, and this terminal is
compliant with RS232C. Also a serial output terminal is provided to enable plural projector control.
Examples of connection
Single projector
Plural projectors
<Terminal section on projector side>
<Terminal section on Projector 1> <Terminal section on Projector 2>
D-Sub 9-pin D-Sub 9-pin D-Sub 9-pin D-Sub 9-pin
PC
D-Sub 9-pin (female)
(female)
(male)
(female)
(male)
PC
D-Sub 9-pin (male)
Communication cable
D-Sub 9-pin
(male)
D-Sub 9-pin
(female)
D-Sub 9-pin
(male)
Communication cable
Communication cable
Pin assignments and signal names
Description
NC
Receive data
Send data
NC
Pin No.
Signal name
Description
NC
Signal name
Pin No.
D-Sub 9-pin (female),
external appearance
D-Sub 9-pin (male),
external appearance
TXD
RXD
Send data
Receive data
Connected internally
Ground
RXD
TXD
Ground
NC
GND
GND
NC
CTS
RTS
RTS
CTS
Connected internally
NC
Connected internally
NC
Serial output terminal
Serial input terminal
Communication conditions (Factory setting)
Signal level
Synchronization method
Baud rate
RS232C compliant
Start-stop synchronization
9 600bps
None
8 bits
1 bit
Parity
Character length
Stop bit
X parameter
S parameter
None
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
STX
A D
I 1 I 2
;
C1 C2 C3
:
P1 P2
Pn
ETX
(2 bytes)
Two ID
characters
(2 bytes)
Colon
(1 byte)
End
(1 byte)
Semicolon
(1 byte)
Start
(1 byte)
ZZ, 1 to 64 and 0A to 0Z
ID designate
3 command
characters (3 bytes)
Parameter
(undefined length)
• No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending
any command after that period has elapsed.
• When sending several commands, be sure to wait for more than 0.5 seconds after receiving a
response from the projector, and then send the next command. When sending commands without
parameters, a colon (:) is not necessary.
Attention
Note
• If an unworkable command is received, the projector will send an “ER401” response to the computer.
• If an invalid command is received, the projector will send an “ER402” response to the computer.
• Projector ID supported on the RS232C interface is ZZ (ALL) and a group of 1 to 64 and 0A to 0Z.
•
If a command is sent with a projector ID specified, the projector will return answer back only in the following cases:
If it coincides with the projector ID,
ID specification is ALL and VPS-SYSTEM is the master, or
ID specification is group and Group is the master.
• In the hexadecimal format, STX has the character code 02 and ETX the character code 03.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the REMOTE 2 terminal
Using the REMOTE 2 terminal provided on the side of the
main unit, it is possible to operate the projector from a
control panel etc. furnished in a distant location where
infrared remote control signal cannot be received.
Control commands
When controlling the projector from a computer, the
following commands are available:
Example of a control panel layout
Function of
command
Remarks
Command
External
control
Remote
terminal
PON Power “ON”
To confirm that the power is
ON, use a “Power query”
Remote terminal
/External control
Power
POF
“STANDBY” command.
ON
STANDBY
Parameter
QPW Power query 000 = STANDBY
001 = Power “ON”
LAMP
RGB1
RGB2
DVI
VIDEO
Parameter
I I S
Switch input
modes
VID = VIDEO SVD = S-VIDEO
RG1 = RGB1 RG2 = RGB2
DVI=DVI
S-VIDEO
Projector set up in a meeting room
Parameter
Query for
QSL active
lamp mode
0 = DUAL
1 = SINGLE
2 = LAMP 1
3 = LAMP 2
Parameter
0 = DUAL
Control panel located
in a different room
“SINGLE” will use
the lamp (LAMP 1
or LAMP 2) with
shorter operating
hours.
Pin assignments and control
Be sure to short-circuit Pins
when controlling.
and
Active lamp
mode
LPM
OLP
1 = SINGLE
2 = Only LAMP 1 is on
3 = Only LAMP 2 is on
Parameter
D-Sub 9-pin (female)
external appearance
Names of terminals
GND
Open (H)
Short (L)
GND
Lamp power
setting
0 = HIGH, 1= LOW
POWER
RGB1
RGB2
VIDEO
S-VIDEO
DVI
OFF
Other
Other
Other
Other
Other
OFF
ON
RGB1
RGB2
VIDEO
S-VIDEO
DVI
• If you need a detailed command list,
please contact your dealer.
Note
Cable specifications
<Connecting to a PC>
SHUTTER
ON
Controlled by
Controlled by
RST / SET
Computer
(DTE specifications)
remote control external contact
Projector
•
The following buttons on the remote
control and the operation area of the
projector can no longer be operated when
Note
1
2
3
4
5
6
7
8
9
NC
NC
1
2
3
4
5
6
7
8
9
pins
and
are shorted: POWER
button and SHUTTER button.
NC
NC
NC
NC
Neither will it be possible to use the
RS232C commands or network functions
corresponding to these functions.
•
If you short pin
short one of the pins from
pin , then the following buttons on the
and pin
, and also
to and
NC
NC
projector operating area and the remote
control can no longer be operated:
POWER, RGB1, RGB2, DVI, VIDEO, S-
VIDEO and SHUTTER buttons.
• To connect the computer to the
SERIAL terminal, prepare an
Attention
adequate communication cable that
fits to your personal computer.
Neither will it be possible to use the
RS232C commands or network functions
corresponding to these functions.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Indication of lamp monitor
This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal
internal temperature. These lamps flash or light up to indicate a problem.
Turn the power off and follow the steps below.
Power indicator
Lamp 2 monitor (LAMP 2)
Lamp 1 monitor (LAMP 1)
Temperature monitor
(TEMP) indicator
Name of monitor
lamp
Lamp
indication
Information
Checkpoint
Remedial measure
• Did you turn on the
• Wait about five minutes in the
power when the
current status.
Warm-up status
ambient temperature • Install the unit in a location
Lighting in
red
(lamp unit
ON)
was low
having an ambient
(approx. 0 °C)?
temperature from 0 to 45 °C.
High temperature
inside. (WARNING)
• Remove the object that is
blocking the ventilation port.
• Move the projector to a
temperature of 0 to 45 ˚C and
the humidity of 20 to 80 % (no
condensation).
• Turn off the MAIN POWER
switch using the procedure on
page 23 and clean the air filter
(refer to page 41).
Temperature
monitor
• Check if the
ventilation port is
blocked.
• Is the room air
temperature too high?
• Is the air filter clogged
with dust?
TEMP
Blinking in
red
(1 time)
The filter is clogged.
High temperature
inside
(Standby condition)
Blinking in
red
(2 times)
• Turn off the main power supply
(MAIN POWER) switch in the
procedure shown on page 23
and consult the distributor.
Blinking in
red
(3 times)
Cooling fan has
been stopped.
• This lamp monitor lights up
when the lamp unit used hours
have reached 1 300 hours
(3 800 hours when long life
lamp units are used). Request
the dealer to replace the lamp
unit.
• Did you notice a
“REPLACE LAMP”
message on the
screen when turning
on the projector
power supply?
Indicates the time
for replacing the
lamp unit.
Lighting in
red
Lamp monitor
• Did you turn the power • Wait until the lamp has cooled
LAMP1
LAMP2
back on immediately
after turning it off?
• Some error has
arisen in the lamp
circuit.
off, and then turn on the
power.
Blinking in Error is detected in
red the lamp or lamp
(3 times) power.
• Turn off the MAIN POWER
switch using the procedure on
page 23 and consult the
• Check for fluctuation
(or drop) in the source dealer.
voltage.
• To solve any problems that the TEMP and LAMP monitor show, first turn the power off by
following the steps on pages 22, 23.
Attention
• If the power indicator blinks in red (3 times), the projector has malfunctioned. Please consult your
dealer.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and replacement of air filter
If too much dust accumulates on the air filter, [AIR FILTER] appears at the lower left of the screen, and the
temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature inside the
main unit will rise, the temperature monitor (TEMP) will blink twice, and the power is turned off.
Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector
operation.
It appears only for 30 seconds within 3 minutes after the power is turned on. It disappears if any of the buttons
on the rear side of the main unit or on the remote control is pressed.
Procedure of cleaning
Turn off the main power and remove the power plug from the receptacle.
Turn off the main power supply observing the procedure (Powering off the projector) on page 23 and then
remove the power plug.
Dismantle the air filter.
There are two air filters, one at the left and one at the right.
Use your finger to pull the air filter tab toward you, and remove it from the main unit.
Clean the air filter.
Suck off deposited dust with a vacuum cleaner.
Air filter
• Do not to suck in the air filter itself.
Attention
• Do not rinse off the air filter with water. Doing so will impair the filter’s ability to provide
protection from dust.
Set the air filter.
Set the air filter in the reverse order to step
.
• Fit the air filters into place with the filter material facing the back.
(The left and right filters have the same shape.)
Attention
• The air filter must be fitted in place when using the projector.
Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector,
causing failure.
• If cleaning cannot remove the dust completely, then it is a sign to replace the air filter. Consult the
dealer. In addition, when the lamp unit is replaced, also replace the air filter.
Note
• Be absolutely sure to use the air filter specifically designed for use with the projector.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp unit
WARNING!
When replacing the lamp, allow it to
cool for at least one hour before
handling it.
Precautions on lamp unit replacement
Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled,
explosion might result.
A used lamp unit may burst if it is handled violently.
For disposition of used lamps, request an industrial waste disposal contractor.
Do not reset the cumulative time, except when the lamp unit has been replaced with a new unit.
If you continue to use a lamp after the replacement time, the lamp may break.
Phillips screwdriver is necessary when replacing a lamp unit.
Take care not to slip your hand when using a screwdriver.
• A lamp unit is an optional part. Contact the dealer.
Replacement lamp unit model No.: ET-LAD55 (single bulb), ET-LAD55W (double bulbs)
Rating: 300W
Attention
Long life lamp unit model No.: ET-LAD55L (single bulb), ET-LAD55LW (double bulbs)
Rating: 160W
• Other lamps than specified above cannot be used. Be sure to use the specified lamp.
Timing of lamp unit replacement
The lamp used for the light source has its due life. The life of light source lamp used in the main unit is 1 500
hours 1 (when “LAMP POWER” is “HIGH” and “LAMP SELECT” is “DUAL”). However, it may happen that the
lamp becomes dead (will not light) by the time of 1 500 hours 1 depending on the characteristics of individual
lamps and working conditions (lamps may reduce their life affected by the times of lighting and the intervals
between previous lighting and next lighting). Therefore, it is strongly recommended for the user to keep a spare
bulb.
If your lamp unit is not replaced after 1 300 hours 2 (with “LAMP POWER” set at “HIGH”), power supply will be
turned off automatically at the time of 1 500 hours 1, entering a standby state. After 1 500 hours 1 of initial
lighting, power supply is turned off automatically about 10 minutes later, entering a standby state even if it is
turned on again.
2
Indication after 1 300 hours (with “LAMP POWER” set at “HIGH”)
When lamp unit used hours have reached 1 300 hours 2, lamp monitor
(LAMP1 or LAMP2) light up including standby state.
Further, an on-screen indication will appear for about 30 seconds as
shown in the diagram on the left, recommending replacement of lamp unit.
(The indication on the left diagram will disappear after about 30 seconds or
REPLACE LAMP
when either control button on the rear of main unit or remote control button
is operated.)
After the time of 1 500 hours 1, the on-screen indication will not disappear
unless the menu (MENU) button is operated.
1 This time period is 4 000 hours when long life lamp units are used.
2 This time period is 3 800 hours when long life lamp units are used.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp unit replacement steps
• After 1 500 hours (4 000 hours when long life lamp units are used) of operating the same lamp, it
Attention
is only possible to operate the unit for approximately 10 minutes. Steps
completed within 10 minutes.
to
must be
Turn the power off by following the steps on page 23, remove the power plug and
confirm that the surroundings of the lamp unit have cooled off.
Check that the fan has stopped running.
Have a Phillips screwdriver ready ahead of time.
Remove the screw securing the lamp unit
cover, and then slide the lamp unit cover
a little toward the left, and remove it.
Remove the two screws securing the
fan unit.
• The lamp units are constructed in such
Note
a way that the screws in steps
and
Lamp unit cover
will not fall through completely.
Lamp unit 2
Open the fan unit as shown in the
figure.
Lamp unit
Fixing screws
Remove the screws securing the lamp
units (two for each unit), take hold of
the handles, and remove the lamp units.
Handle
Lamp unit 1
Install the new lamp unit.
Caution
The lamp unit will be hot after it has
been used.
You might get burned if you touch it while it is
still hot.
Use a Phillips screwdriver to securely
tighten the 2 lamp unit fixing screws
(two for each unit).
Secure the two screws for securing the
fan unit tightly.
Slide the cover a little toward the right,
and secure it using the screw for
securing the lamp unit cover tightly.
• Firmly install the lamp unit and lamp
unit cover. If not installed firmly, a
protection circuit will function and the
power will not be turned on.
Attention
(Continued on next page)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp unit
Insert the power cord plug into the wall outlet and then
press the MAIN POWER switch.
• If the power does not turn on even after turning the MAIN
POWER switch “I”, turn the MAIN POWER “O”, confirm that
the lamp unit and door are installed correctly, and turn on
again.
Attention
Press the “ I ” button so that a picture is projected onto
the screen.
MENU
PICTURE
POSITION
Press the “MENU” button to display the MAIN MENU
screen, and then press the
and
buttons to move
ADVANCED MENU
LANGUAGE
OPTION1
OPTI0N2
the cursor to select “OPTION2”.
Press the “ENTER” button to display the “OPTION2”
screen, and select “SYSTEM INFORMATION” with the
and
buttons.
SYSTEM INFORMATION
ROM VERSION
SET RUNTIME
LAMP1 LOW
HIGH
1. 00. 00
300h
100h
Press the “ENTER” button.
The SYSTEM INFORMATION screen will be displayed.
200h
TOTAL
300h
LAMP2 LOW
100h
Press and hold the “ENTER” button on the projector or
the remote control for approximately 3 seconds.
An item “LAMP TIME RESET” will be added.
LAMP TIME RESET
LAMP1
LAD55
LAD55L
LAMP2
LAD55
LAD55L
1433h
0h
Select the lamp which has been replaced with the
buttons.
and
1100h
0h
LAMP1: Replace the LAMP UNIT 1
LAMP2: Replace the LAMP UNIT 2
Press the ENTER button, and when the “LAMP TIME
RESET” display flashes, press the ENTER button again.
The used hours of the specified lamp unit will be reset to zero.
When more than one lamp has been replaced, repeat the procedure from
step
.
• When the “LAMP TIME RESET” display flashes, the lamp
time reset can be canceled by pressing the MENU button.
• The used hours of the lamp units can also be reset to zero
Note
by taking the following action instead of steps
to
.
When lamp unit 1 has been replaced:
In the standby mode, press the number buttons in the
sequence of 737381, and then press the ENTER button.
When lamp unit 2 has been replaced:
In the standby mode, press the number buttons in the
sequence of 737382, and then press the ENTER button.
When the used hours have been reset, the lamp monitor
(LAMP1/LAMP2) will flash for 3 seconds.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Web Browser Control
This projector has networking functions which allow it to be controlled through a web browser on a PC.
The controlled items are:
• Projector’s settings and adjustment
• Projector’s status display
• Transmission of a E-mail message when the projector has a problem
Accessing from the Web browser
Start the web browser on your PC, then
enter the IP address which was set in
the projector.
Enter “user1” in the user name field,
then enter the password in the
password field.
The default setting is “panasonic” (all lower case). If
you have changed the password, enter the new
password here.
The host name set in the projector is displayed in
the “Realm” field.
Click [OK].
The Basic Control page is displayed.
• Avoid activating two or more Web browser
simultaneously to work out setting or
control actions.
Note
• Change the password first of all.
Password change page
Click [Change password].
Old password input field
New password input field
New password input field
(re-enter for confirmation)
Button for executing password change
Button for erasing all entered characters
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Web Browser Control
Basic control page
This page is the first page displayed when the projector is accessed through a web browser.
To move from another page, click [Projector control], then [Basic control].
Control button
Click this item, and a
projector control page
appears.
E-mail set up button
Click this item, and an E-
mail setting page appears.
Monitor information
button
Click this item, and the
status of the projector is
displayed.
Network set up button
Click this item, and a network set up page for IP address and other items appear.
Change password button
Power On/Off control Shutter control
OSD
(On-screen Display)
display/non-display
Use these to select
the input signals.
Signal System
Switching
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
On-screen status is
displayed, even if the on-
screen of projector is set
to off.
Temporary stop of video
Lens adjustment
Test pattern display
This button updates the
on-screen description on
the right of the control
page with the latest
information.
Pressing these buttons controls the projector and updates the on-screen
description on the right of the control page when control is finished.
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays the input
switching status.
Displays temperature of
projector’s intake air.
Displays temperature
inside the projector.
Displays temperature
around the lamp.
Displays the lamp1 lit
hours.
Displays the lamp2 lit
hours.
Displays used hours of the
projector.
Displays self-diagnosis
information.
Displays the type
of projector.
Displays the firmware version
of the projector main unit.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Web Browser Control
Error information page
When
is displayed on the status information screen, click it to display the error details.
OK: Normal operation
FAILED: Occurrence of trouble
• Depending on the nature of the error, the projector may be placed in the standby mode for its own
protection.
Note
When [FAILED] has appeared for an item
Parameter
Description
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. It may be that the projector is
being used where the ambient temperature is high such as near a heating
appliance.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being
used where the ambient temperature is high such as near a heating
appliance.
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
The temperature near the lamp has risen very high.
Something may be blocking the exhaust vent.
The lamp runtime has exceeded the prescribed cumulative time, and it is
now time to replace the lamp.
LAMP STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
Trouble has occurred in the shutter circuitry. Consult your dealer.
Too much dust accumulates on the air filter.
SHUTTER
AIR FILTER
Turn off the MAIN POWER switch using the procedure on page 23 and
clean the air filter (refer to page 41).
Trouble has occurred in the temperature detection sensor inside the
projector. Consult your dealer.
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
AROUND LAMP
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
Trouble has occurred in the temperature detection sensor around lamps.
Consult your dealer.
The backup battery has been run out. Consult your dealer.
Trouble has occurred in the air volume sensor. Consult your dealer.
Trouble has occurred in the colour wheel or the colour wheel drive circuit.
Consult your dealer.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail setup page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be
sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail
set up] to display the E-mail setup page.
Select “Enable” to use
the E-mail function.
Enter the IP address or server name of the E-mail server (SMTP).
The DNS server must be set if the server name is entered.
Enter the E-mail address of the
projector.
(maximum 63 characters)
The user can enter the location
of, for example, the installed
projector so that the recipient
may easily identify the
originator of the E-mail.
(maximum 63 characters)
The user can modify the
minimum time interval of
temperature warning mail. The
default value is 60 minutes. In
this case, the user cannot send
another mail for 60 minutes
after sending previous
temperature warning mail even
the set warning temperature is
reached again.
The user can modify the threshold temperature for sending
temperature warning mail. If the temperature rises above the set value,
control sends temperature warning mail.
Enter the E-mail address of
your desired recipient.
Select the conditions for
sending E-mail.
ERROR:
an error is detected by self-
diagnosis.
LAMP RUNTIME: remaining
lamp service time has reached
the value set in the field.
INPUT AIR TEMPERATURE:
intake air temperature has
reached the value set in the field.
Periodic warning interval setting
(e-mail is sent on the checked
days of the week/times)
(Continued on next page)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Web Browser Control
E-mail setup page (continuing)
Enter the E-mail address to
which the E-mail is to be sent
when two E-mail addresses
are going to be used. Do not
enter it when the second E-
mail address is not going to
be used.
Check these boxes when E-
mail is to be sent periodically
to two E-mail addresses. E-
mail will be sent at the times
and on the days checked.
Button to update settings
Select the conditions for sending the second E-mail.
ERROR: an error is detected by self-diagnosis.
LAMP RUNTIME: remaining lamp service time has reached the value set in the field.
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field.
Note
• Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an e-mail address.
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
Primary DNS server
address
Available input characters:
Numbers (0 - 9), period (.)
(ex. 192.168.0.253)
Secondary DNS server
address
Available input characters:
Numbers (0 - 9), period (.)
(ex. 192.168.0.254)
Button to update settings
50
Download from Www.Somanuals.com. All Manuals Search And Download.
POP server setup page
The POP server is set on this page when POP authentication is required for mail transmissions.
Click [Network set up], then [POP server set up] to display the POP server setup page.
Select “Enable” for this setting
only when authentication is
required for sending mail.
POP server name field
Available input characters:
Alphanumeric characters
(A–Z, a–z, 0–9), hyphen (-),
period (.)
POP server user name field
POP server password field
Button to update settings
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS
server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Enter the IP address of the
server to be tested.
Button for conducting the
test.
Display which appears
when the connection was
successful.
Display which appears
when the connection failed.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Web Browser Control
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
• Mail with the contents shown below is sent
settings have been established.
when an error has occurred.
=== Panasonic projector report(CONFIGURE) ===
=== Panasonic projector report(ERROR) ===
Projector Type
: D5600
Projector Type
: D5600
––––– check system –––––
MAIN CPU BUS
----- E-mail setup data -----
[
[
[
[
[
[
[
[
[
OK
OK
OK
OK
OK
OK
OK
OK
OK
]
]
]
]
]
]
]
]
]
TEMPERATURE WARNING SETUP
FAN
MINIMUM TIME
at [ 60] minutes interval
OPTICS MODULE TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP TEMPERATURE
LAMP2 REMAIN TIME
LAMP1 REMAIN TIME
LAMP2 STATUS
INPUT AIR TEMPERATURE Over [ 45C / 113F ]
ERROR
[ ON ]
LAMP1 RUNTIME
LAMP1 RUNTIME
LAMP2 RUNTIME
LAMP2 RUNTIME
[ ON ] at REMAIN [ 100] H
[ ON ] at REMAIN [ 200] H
[ ON ] at REMAIN [ 300] H
[ ON ] at REMAIN [ 400] H
LAMP1 STATUS
SHUTTER
[ FAILED ]
INPUT AIR TEMPERATURE [ OFF ]
AIR FILTER
[
[
[
[
[
[
[
OK
OK
OK
OK
OK
OK
OK
]
]
]
]
]
]
]
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP TEMP.SENSOR
BATTERY
PERIODIC REPORT
Sunday [ ON ] Monday [ OFF ] Tuesday [ ON ] Wednesday [ OFF ]
Thursday [ ON ] Friday [ OFF ] Saturday [ ON ]
AIRFLOW SENSOR
COLOR WHEEL
00:00 [ ON ] 01:00 [ OFF ] 02:00 [ ON ] 03:00 [ OFF ]
04:00 [ OFF ] 05:00 [ ON ] 06:00 [ OFF ] 07:00 [ ON ]
08:00 [ ON ] 09:00 [ OFF ] 10:00 [ ON ] 11:00 [ OFF ]
12:00 [ OFF ] 13:00 [ ON ] 14:00 [ OFF ] 15:00 [ ON ]
16:00 [ ON ] 17:00 [ OFF ] 18:00 [ ON ] 19:00 [ OFF ]
20:00 [ OFF ] 21:00 [ ON ] 22:00 [ OFF ] 23:00 [ ON ]
(Error code 00 10 00 00 00 00 00 00)
Input air temperature
: 30 degC / 86 degF
Optics module temperature : 30 degC / 86 degF
Around lamp temperature : 37 degC / 98 degF
SET RUNTIME
POWER ON
30 H
33 times
34 times
25 H
----- check system -----
LAMP1 ON
MAIN CPU BUS
[
[
[
[
[
[
[
OK
OK
OK
OK
OK
OK
OK
]
]
]
]
]
]
]
LAMP1 LOW
LAMP1 HIGH
LAMP2 ON
LAMP2 LOW
LAMP2 HIGH
LAMP1 REMAIN
LAMP2 REMAIN
FAN
5 H
OPTICS MODULE TEMPERATURE
24 times
16 H
INPUT AIR TEMPERATURE
AROUND LAMP TEMPERATURE
4 H
LAMP2 REMAIN TIME
LAMP1 REMAIN TIME
•
•
•
1476 H
1484 H
----- Network configuration -----
IP address 192.168.0.8
MAC address 00:00:00:00:00:00
Thu Mar 02 14:11:02 2006
----- Memo -----
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
Time zone selection
Button to update time zone
setting
New date field
Button to update time and
date settings
New time field
• If the time becomes incorrect immediately after setting the correct time, then the battery needs to
be changed. Contact the dealer where you bought the projector to have the battery changed.
Note
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Network config page
Set this to ON to enable the
DHCP client function.
Enter the IP address if DHCP
server is not used.
Enter the subnet mask if
DHCP server is not used.
Enter the gateway address if
DHCP server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance.
Network status page
Click [Network set up], then [Network status] to display the Network status page.
Network software version
display
Set IP address display
Set subnet mask display
MAC address display
Network status display
53
Download from Www.Somanuals.com. All Manuals Search And Download.
™
Using the PJLink protocol
The network functions of the projector are compatible with PJLink™ Class 1. The operations mentioned below
can be performed from a personal computer using the PJLink™ protocol.
• Projector settings
• Projector status inquiry
Supported commands
The commands for controlling the projector using the PJLink™ protocol are as given in the table below.
Remarks
Command
Control Description
Power control
Parameter
0 = Standby
1 = Power “ON”
Parameter
POWR
0 = Standby
1 = Power “ON”
2 = Cooling down
3 = During warm-up
Parameter
POWR ? Power status inquiry
11 = RGB1
INPT
Input selection
12 = RGB2
21 = VIDEO
22 = S-VIDEO
31 = DVI
INPT ?
Input selection inquiry
Parameter
AVMT
Shutter control
30 = Shutter mode OFF (Mute reset of video)
31 = Shutter mode ON (Mute video)
Parameter
AVMT ?
Shutter status inquiry
1st byte: Refers to fan error; one of 0 to 2
2nd byte: Refers to lamp error; one of 0 to 2
3rd byte: Refers to temperature error; one of 0 to 2
4th byte: 0 fixed
ERST ?
Error status inquiry
5th byte: Refers to filter warning; one of 0 to 2
6th byte: Refers to some other error; one of 0 to 2
The meaning of 0 to 2 is as given below.
0 = Error not detected 1 = Warning 2 = Error
Parameter
First number (digits 1 to 5): Lamp cumulative time
Second number: 0 = Lamp OFF; 1 = Lamp ON
Parameter responds with following values:
“11 12 21 22 31”
LAMP ?
INST ?
Lamp status inquiry
Input selection list inquiry
Responds with the name set in “HOST NAME” of “NETWORK”
Responds with “Panasonic”
Responds with “D5600” or “DW5000”
Responds with version number and so on
Responds with “1”
NAME ? Projector name inquiry
INF1 ?
INF2 ?
INFO ?
CLSS ?
Manufacturer's name inquiry
Model name inquiry
Other information inquiry
Class information inquiry
™
PJLink security authentication
The password used in PJLink™ is the same as the password set in the Web Browser Control. To use PJLink™
without authentication, do not set any password in Web Browser Control.
PJLink™ is the applied-for trademark or a registered trademark in Japan, USA, and in other countries and
regions. For specifications of PJLink™, see the website of the Japan Business Machine and Information
System Industries Association.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Before asking for service
---Before asking for service, check the following points.
Symptoms
Checks
• Is the power cord plug correctly plugged in?
• Is the MAIN POWER turned on?
• Is electricity running to the power outlet?
• Is the temperature monitor (TEMP) indicator on the front of the unit flashing or
turned on? (See page 40)
• Is the lamp monitor (LAMP) indicator on the front of the unit flashing or turned on?
(See page 40)
Power does
not turn on
• Is the lamp unit door installed correctly?
• A wrong ID is set. (See pages 15 and 34)
• Is the lens cap still on the lens?
• Is the image input correctly connected?
• Is the input mode set correctly? (See page 22)
• Is the black level adjustment set at the minimum level? (See page 28)
• Is the equipment connected to the projector operating correctly?
• Is the shutter function turned on? (See page 25)
No image
• Is the lens focused properly? (See page 24)
• Is the projection distance correct? (See pages 17 to 18)
• Is the lens dirty?
Image is blurred
• Is the projector positioned directly in front of the screen? (See page 16)
Light colour/
• Is the colour density and colour tone setting correct? (See page 28)
• Is the equipment connected to the projector correctly adjusted?
bad colour tone
• Are the batteries exhausted?
• Are the battery polarities set correctly? (See page 14)
• Are there any obstacles between the remote control and the remote control
sensor? (See page 14)
• Are you trying to operate the remote control beyond its operable range?
(See page 14)
• Are you controlling from external equipment using the REMOTE2 terminal?
(See page 39)
Remote control
does not operate
• Is there any external light interfering with remote control operation?
• A wrong ID is set. (See pages 15 and 34)
• Is the on-screen display function at “OFF”? (See page 9)
• Is the input mode properly set? (See page 22)
• Is the correct signal system (TV system) selected? (See page 29)
• Are there any malfunctions on the source side, such as bad video tapes?
• Are you inputting a signal that is not compatible with this projector? (See page 57)
Abnormal image
• Is the cable too long?
• Is the video output signal setting of the computer correctly set?
(Read the operating instructions of the your PC.)
Does not display
images from PCs
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model No.
PT-D5600E
PT-D5600EL PT-DW5000E PT-DW5000EL
Power supply
AC 220-240 V, 50 Hz/60 Hz
Power consumption
750 W (about 15 W in standby without fan running)
TM
DLP panel
0.7 inch (aspect ratio 4:3)
0.65 inch (aspect ratio 15:9)
Panel size
Display system
Number of pixels
TM
TM
DMD element, DLP type
786 432 pixels (1 024 x 768 dots)
983 040 pixels (1 280 x 768 dots)
1 to 1.32
Lens
Powered zoom
Powered focus control
1 to 1.32
F=1.7 to 2.0
f=25.6 mm to
33.8 mm
F=1.7 to 2.0
f=25.6 mm to
33.8 mm
Option
Option
Projection lamp
Optical output
2 bulbs x 300 W UHM lamp
1
1
5 000 lm
4 500 lm
Applicable scanning frequency
For video signal (S-video included)
For RGB signal
Horizontally 15.73 kHz/15.63 kHz, vertically 59.94 Hz/50 Hz
Horizontally 15 kHz–91 kHz, vertically 50 Hz–85 Hz,
Panasonic Intelligent Auto Scanning (PIAS) system
Dot clock frequency Less than 108 MHz
2
For DVI-D signal
For YPBPR signal
Compliant with HDCP
EDID1:480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i
EDID2:VGA60, SVGA60, XGA50, XGA60, XGA70, XGA85,
WXGA768/50, WXGA768/60, SXGA60
[480i], horizontally 15.73 kHz, vertically 59.94 Hz
[480p], horizontally 31.5 kHz, vertically 59.94 Hz
[576i], horizontally 15.63 kHz, vertically 50 Hz
[576p], horizontally 31.25 kHz, vertically 50 Hz
[720/60p], horizontally 45 kHz, vertically 60 Hz
[720/50p], horizontally 37.5 kHz, vertically 50 Hz
[1035/60i], horizontally 33.75 kHz, vertically 60 Hz
[1080/60i], horizontally 33.75 kHz, vertically 60 Hz
[1080/50i], horizontally 28.13 kHz, vertically 50 Hz
• HD/SYNC, VD terminals are not compliant with 3 value composite
SYNC.
Colour system
Screen size
7 standards (NTSC/NTSC4.43/PAL/PAN-N/PAL-M/SECAM/PAL60)
50 inch–600 inch
Screen aspect ratio
Projection scheme
Contrast ratio
4:3
15:9
Menu-selectable from front/rear/ceiling mount, and floor standing
2 000:1 (when “HIGH” is selected as the “CONTRAST MODE” setting)
Interface ports
RGB1 input terminal
1 set, BNC x 5
[For YPBPR input]
Y: 1.0 V[p-p] synchronization signal included, PBPR: 0.7 V[p-p] 75 Ω
[For RGB input] 0.7 V[p-p] 75 Ω For G-SYNC: 1.0 V[p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity
automatically adjusted
VD: TTL, high-impedance, positive/negative polarity automatically
adjusted
• However, HD/SYNC, and VD terminals are not compliant with 3-value
direct SYNC.
1 These values are for the lens provided with the PT-D5600E/PT-DW5000E. Note that these values change
according to the lens used.
2 HDCP (High-bandwidth Digital Content Protection)
HDCP is a digital video signal encryption system developed with the aim of protecting digital content.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Model No.
PT-D5600E
PT-D5600EL PT-DW5000E PT-DW5000EL
Interface ports
RGB2 input terminal
1 set of high-density, D-sub 15p (female)
[For YPBPR input]
Y: 1.0 V [p-p] synchronization signal included, PBPR: 0.7 V[p-p] 75 Ω
[For RGB input] 0.7 V[p-p] 75 Ω For G-SYNC: 1.0 V[p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity
automatically adjusted
VD: TTL, high-impedance, positive/negative polarity automatically adjusted
• However, HD/SYNC, and VD terminals are not compliant with 3-value
direct SYNC.
Video input terminal
1 set BNC
1.0 V[p-p] 75 Ω
S-video input terminal
Serial input/output terminal
Remote1 input/output terminal
Remote2 terminal
1 set Mini DIN 4p
Y 1.0 V[p-p] C 0.286 V[p-p] 75 Ω Compliant with S1 signals
D-sub 9-pin (male/female), RS232C compliant
Used for personal computer control
1 set each for M3 stereo mini jack
Wired remote control, used for link control
D-sub 9-pin (female)
Used for external control
DVI-D terminal
LAN terminal
DVI-D 24-pin Single link, compatible with HDCP
RJ-45 Compliant with PJLink
TM
Length of power supply cord
Cabinet
3.0 m
Molded resin
Outside dimensions
Mass
Width: 530 mm; Height : 167 mm; Depth: 425 mm
14.5 k
14.0 k
14.5 k
14.0 k
3 Ambient temperature: 0 °C to 45 °C
Working environment condition
Ambient humidity: 20 % to 80 % (no condensation)
Remote control
Power source
Operation range
Mass
3 V DC (two AAA dry cells)
approx. 7 m (in front of beam receiver)
95 (including dry cells)
Outside dimensions
Width: 45 mm, Thickness: 23 mm, Depth: 145 mm
Option
Hanging attachment
(For high ceiling)
Hanging attachment
(For low ceiling)
Projection lens
ET-PKD55
ET-PKD55S
PT-D5600E/PT-D5600EL
ET-DLE100, ET-DLE200, ET-DLE300, ET-DLE400, ET-DLE050
PT-DW5000E/PT-DW5000EL
ET-DLE100, ET-DLE200, ET-DLE310, ET-DLE410, ET-DLE050
ET-RMRC2
ET-LAD55 (single bulb), ET-LAD55W (double bulbs)
ET-LAD55L (single bulb), ET-LAD55LW (double bulbs)
Wireless mouse receiver
Replacement lamp unit
Long life lamp unit
• The outside dimensions do not include the lens and other protruding parts. See page 59 for further details.
3 When using the projector at high altitudes (1 400 to 2 700 m), the upper limit for the ambient temperature drops
by 5 °C.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatible Signal List
Resolution
(as a number
of dots)
Scanning frequency Dot clock
Horizontal Vertical frequency
Image
quality
Display mode
Format
(kHz)
(Hz)
(MHz)
NTSC/NTSC4.43/
PAL-M/PAL60
PAL/PAL-N/SECAM
480i
720 x 480i
15.7
59.9
A
Video/S-Video
Video/S-Video
720 x 576i
720 x 480i
720 x 576i
720 x 483
15.6
15.7
15.6
31.5
31.3
33.8
28.1
45.0
37.5
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
68.7
35.5
64.0
67.5
76.7
41.3
49.7
39.6
47.7
68.7
60.0
64.0
80.0
91.1
64.0
75.0
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.1
75.0
85.1
74.6
50.0
60.0
70.1
75.0
85.0
87.0
71.2
74.9
85.0
50.0
59.8
50.0
60.0
75.1
60.0
60.0
75.0
85.0
60.0
60.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
94.5
44.9
94.2
108.0
121.5
68.6
83.5
65.2
80.1
100.0
108.0
108.0
135.0
157.5
108.0
162.0
YPBP
YPBP
R/RGB
R/RGB
576i
480p
576p
1080/60i
1080/50i
720/60p
720/50p
VGA400
YPB
YPB
YPB
YPB
YPB
YPB
P
P
P
P
P
P
R/RGB/DVI
R/RGB/DVI
R/RGB/DVI
R/RGB/DVI
R/RGB/DVI
R/RGB/DVI
RGB
720 x 576
1 920 x 1 080i
1 920 x 1 080i
1 280 x 720
1 280 x 720
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768
1 024 x 768i
1 152 x 864
1 152 x 864
1 152 x 864
1 280 x 800
1 280 x 800
1 280 x 768
1 280 x 768
1 152 x 870
1 280 x 960
1 280 x 1 024
1 280 x 1 024
1 280 x 1 024
1 400 x 1 050
1 600 x 1 280
RGB
VGA480
SVGA
RGB/DVI
RGB
RGB
RGB
RGB
RGB
RGB/DVI
RGB
RGB
RGB
RGB
RGB/DVI
RGB/DVI
RGB/DVI
RGB/DVI
RGB/DVI
RGB
RGB
RGB
RGB
RGB
RGB
A
A
A
A
MAC16
XGA
A
AA
AA
AA
AA
AA
AA
A
A
B
A
A
AA
AA
A
A
A
B
B
A
B
MXGA
WXGA
RGB/DVI
RGB/DVI
RGB
MAC21
MSXGA
SXGA
RGB
RGB/DVI
RGB
RGB
RGB/DVI
RGB
UXGA
1 Character “i” that follows the number of displayed dots stands for interlace signal.
2 The symbols used to denote the image quality have the following significance:
AA = the images are projected at the highest quality (With XGA for the PT-D5600E/PT-D5600EL; with
XGA/WXGA 1 280 x 768 for the PT-DW5000E/PT-DW5000EL); A = the images are converted by the image
processing circuit and projected; B = the amount of data is scaled down and simplified images are projected.
3 These signals support the frame lock function.
• The number of display dots are 1 024 x 768 for PT-D5600E/PT-D5600EL, and 1 280 x 768 for PT-
DW5000E/PT-DW5000EL. If signals with a number of display dots differing from the data listed
above are supplied, they will be converted into signals with 1 024 x 768 dots and displayed for PT-
D5600E/PT-D5600EL, and 1 280 x 768 for PT-DW5000E/PT-DW5000EL.
Note
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
unit : mm
478.5
R/PR
G/Y
B/PB
SYNC/HD
VD
VIDEO IN
S-VIDEO IN
IN
RGB
REMOTE
1
IN
RGB
OUT
2
IN
DVI-D IN
LAN
REMOTE
1
2
IN
SERIAL
OUT
>PC<
TBMU448
436
530
Installation dimensions diagram
(Figure 1 :
(Figure 2 :
Dimensions applying when one unit is used)
Dimensions applying when two units are used)
50 cm or more
Exhaust
50 cm or more
Exhaust
50 cm or more
50 cm or more
Exhaust
10 cm or more
• Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be
blocked.
Attenzione
• Be careful not to retain exhausted air on the back side of the main unit. Also take steps to ensure
that the hot air blown out from the air exhaust outlet will not be sucked into the air intake.
• Install with clearances of at least 30 cm provided for the side panels to enable the air filter to be
removed and re-installed.
• When the projector is to be placed inside a box and used, leave the clearances shown in Fig. 2
and ensure that the temperature during operation remains within the 0 to 35 °C range.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection
points, where they will be accepted on a free of charge basis. Alternatively, in some countries you
may be able to return your products to your local retailer upon the purchase of an equivalent new
product.
Disposing of this product correctly will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling. Please contact your local authority for further details of your nearest designated
collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of
disposal.
Note:
Purchase of this equipment includes the rights to use this software (the built-in microcomputer and information
recorded on ROMs) but does not grant copyrights. Do not reverse engineer, change or modify the software.
The guarantee will not be valid for any malfunctions caused by such actions.
Trademark Acknowledgement
• Digital Light Processing, DLP, and Digital Micromirror Device, DMD are registered trademarks of the Texas
Instruments.
• VGA and XGA are trademarks of International Business Machines Corporation.
• S-VGA is a registered trademark of the Video Electronics Standards Association.
• “Microsoft Windows” is a registered trademark of the Microsoft Corporation (U.S.A.) in the U.S. and other
countries.
• “Netscape” and “Netscape Navigator” are registered trademarks of the Netscape Communications Corporation
in the U.S. and other countries.
• PJLink is the applied-for trademark or a registered trademark in Japan, USA, and in other countries and
regions.
• HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI
Licensing LLC.
All other trademarks are the property of the various trademark owners.
Matsushita Electric Industrial Co., Ltd
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
M0506-0
Download from Www.Somanuals.com. All Manuals Search And Download.
|