Operating Instructions
High Definition Video Camera
Model No.
AG-HSC1UP
Before connecting, operating or adjusting this product, please read the instructions completely.
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC NOTICE (USA)
Declaration of Conformity
Model Number:
Trade Name:
AG-HSC1UP
PANASONIC
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Panasonic Broadcast & Television Systems Company 1-800-524-1448
Support contact:
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make
any unauthorized modifications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and receiver.
≥Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
≥Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface
cables when connecting to host computer or peripheral devices. Also, any unauthorized changes
or modifications to this equipment could void the user’s authority to operate this device.
NOTIFICATION (Canada)
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numéique de la classe B est conforme à la norme NMB-003 du Canada.
indicates safety information.
AG-HSC1UP
3
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Batteries
1) Battery pack (Lithium ion battery pack)
≥Use the specified unit to recharge the battery pack.
≥Do not use the battery pack with equipment other than the specified unit.
≥Do not get dirt, sand, liquids, or other foreign matter on the terminals.
≥Do not touch the plug terminals (i and j) with metal objects.
≥Do not disassemble, remodel, heat or throw into fire.
2) Button-type battery (Lithium battery)
≥Insert with poles aligned.
≥Do not touch the terminals (i and j) with metal objects.
≥Do not recharge, disassemble, remodel, heat or throw into fire.
≥Keep out of reach of children
If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with
water.
If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes
thoroughly with water, and then consult a doctor.
Warning
Risk of fire, explosion and burns. Do not disassemble.
Do not heat the batteries above the following temperatures or incinerate.
Button-type battery 60 oC (140 oF)
Battery pack
60 oC (140 oF)
AC adaptor
This AC adaptor operates on AC between 110 V and 240 V.
But
≥In the U.S.A. and Canada, the AC adaptor must be connected to a 120V AC power supply only.
≥When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the
AC outlet configuration.
≥When connecting to a supply of greater than AC 125V, ensure the cord you use is suited to the
voltage of the AC supply and the rated current of the AC adaptor.
≥Contact an electrical parts distributor for assistance in selecting a suitable AC plug adaptor or AC
cord set.
Marking sign is located on bottom of the unit.
U.S.A./CANADA CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
<For USA-California only>
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
4
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the
unit and the applicable safety instructions listed below. Keep these operating instructions handy for
future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods
of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
5
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE
Precautions
≥TO CLEAN YOUR CAMERA ... Do not use
strong or abrasive detergents when cleaning
your camera body.
USE & LOCATION
WARNING
≥TO PROTECT THE LENS ... Do not touch the
surface of the lens with your hand. Use a
commercial camera lens solution and lens
paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
≥TO PROTECT THE FINISH OF YOUR
CAMERA ... Before handling your camera,
make sure your hands and face are free from
any chemical products, such as suntan lotion,
as it may damage the finish.
≥TO AVOID SHOCK HAZARD ... Your camera
and power supply should not be exposed to
rain or moisture. Do not connect the power
supply or operate your camera if it gets wet.
Your camera has been designed for outdoor
use, however it is not designed to sustain direct
exposure to water, rain, sleet, snow, sand,
dust, or a direct splashing from a pool or even a
cup of coffee. This action could permanently
damage the internal parts of your camera. Do
not attempt to disassemble this unit. There are
no user serviceable parts inside. Unplug your
camera from the power supply before cleaning.
≥AS WITH ANY SMALL OBJECT, SD CARDS
CAN BE SWALLOWED BY YOUNG
-If you see this symbol-
Information on Disposal in other Countries
outside the European Union
CHILDREN. DO NOT ALLOW CHILDREN TO
HANDLE THE SD CARD.
This symbol is only valid in the
European Union.
If you wish to discard this
product, please contact your
local authorities or dealer and
ask for the correct method of
disposal.
CAUTION
≥DO NOT AIM YOUR CAMERA AT THE SUN
OR OTHER BRIGHT OBJECTS
≥DO NOT LEAVE THE CAMERA WITH THE
EVF AIMED DIRECTLY AT THE SUN AS
THIS MAY CAUSE DAMAGE TO THE
INTERNAL PARTS OF THE EVF
≥DO NOT EXPOSE YOUR CAMERA TO
EXTENDED HIGH TEMPERATURE ... Such
as, in direct sunlight, inside a closed car, next
to a heater, etc... This action could permanently
damage the internal parts of your camera.
≥AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the SD card and inside
the unit.
≥DO NOT LEAVE YOUR CAMERA OR THE
POWER SUPPLY TURNED ON WHEN NOT
IN USE.
≥STORAGE OF YOUR CAMERA ... Store and
handle your camera in a manner that will not
subject it to unnecessary movement (avoid
shaking and striking). Your camera contains a
sensitive pick-up device which could be
damaged by improper handling or storage.
6
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
≥IBM and PC/AT are registered trademarks of
International Business Machines Corporation of
the U.S.
≥Intel , Pentium and Celeron are the
registered trademarks or trademarks of the
Intel Corporation in the United States and other
countries.
ª Indemnity concerning recording
content
The manufacturer shall in no event be liable for
the loss of recordings due to malfunction or
defect of this unit, its accessories or recordable
media.
®
®
®
≥Other names of systems and products
mentioned in these instructions are usually the
registered trademarks or trademarks of the
manufacturers who developed the system or
product concerned.
IMPORTANT
ª Carefully observe copyright laws
Whatever you have recorded and created can
be used for your personal entertainment only.
Under copyright laws, other materials cannot
be used without obtaining permission from
the holders of the copyrights.
This product is licensed under the AVC patent
portfolio license for the personal and non-
commercial use of a consumer to (i) encode
video in compliance with the AVC Standard
(“AVC Video”) and/or (ii) decode AVC Video that
was encoded by a consumer engaged in a
personal and non-commercial activity and/or was
obtained from a video provider licensed to
provide AVC Video. No license is granted or shall
be implied for any other use. Additional
ª Cards that you can use with this
unit
SD Memory Card and SDHC Memory Card
For the purposes of these operating instructions,
the following cards are referred to as “the SD
card”.
SD Memory Card
SDHC Memory Card
information may be obtained from MPEG LA,
LLC. See http://www.mpegla.com.
≥SDHC Logo is a trademark.
≥miniSD Logo is a trademark.
≥“AVCHD” and the “AVCHD” logo are
trademarks of Matsushita Electric Industrial
Co., Ltd. and Sony Corporation.
≥Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
≥HDMI, the HDMI Logo and the High-Definition
Multimedia Interface are the registered
trademarks or trademarks of HDMI Licensing
LLC.
≥HDAVI Control™ is a trademark of Matsushita
Electric Industrial Co., Ltd.
≥LEICA is a registered trademark of Leica
Microsystems IR GmbH and DICOMAR is a
registered trademark of Leica Camera AG.
®
®
®
≥Microsoft , Windows and DirectX are either
registered trademarks or trademarks of the
Microsoft Corporation in the United States and/
or other countries.
≥Microsoft product screen shot(s) reprinted with
permission from Microsoft Corporation.
7
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Auto Ground-Directional Standby
Recording motion pictures .................45
Recording modes/recordable time
Features of the High Definition Video
Camera...............................................13
Accessories..........................................18
Using the LCD monitor........................24
Cards that you can use
Microphone level...................................... 60
Color bar .................................................. 62
Manual recording functions................63
Scene mode............................................. 63
Manual shutter speed/aperture
Selecting a mode
Inserting/removing an SD card...........34
How to use the cursor button .............35
Using the menu screen........................39
Setting date and time...........................41
Switching the language.......................42
Adjusting LCD monitor........................42
Motion picture playback......................68
Playing back motion pictures by date ...... 71
Repeat playback ...................................... 71
Resuming the previous playback............. 72
Still picture (JPEG) playback ..............72
8
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Editing scenes......................................74
Deleting scenes........................................74
Protecting scenes.....................................75
Protecting still pictures .............................77
DPOF setting............................................78
Menu list................................................. 105
Menus related to [ADVANCED] and
Functions that cannot be used
Limited Warranty
Formatting an SD card .............................79
With other products
(For USA Customers) .....................129
LIMITED WARRANTY STATEMENT
(For Canadian Customers).............131
Spanish Quick Use Guide/Guía
With a TV...............................................80
Playback using EZ Sync™
(HDAVI Control™).............................87
Dubbing images onto a connected
Before using with a computer.............92
Contents on provided CD-ROM ...............93
End User License Agreement ..................94
Operating environment.............................95
Installing HD Writer Ver1.0E for SD1 .......97
Reading the operating instructions
Connection and recognition ...............99
Connection and recognition procedures...99
About the computer display....................100
To disconnect USB cable safely.............101
Verifying the unit is correctly
recognized by the computer ...............101
Using HD Writer Ver1.0E for SD1......102
If using Macintosh..............................104
9
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
ª Removing the battery
1) Open the battery cover.
Quick Guide
ª Charging the battery
A
2) Remove the battery.
≥Move A in the direction of the arrow to
unlock it and then remove the battery.
1) Connect the AC cable to the AC adaptor
and the AC outlet.
2) Put the battery on the battery mount by
aligning the mark, and then securely plug
it in.
≥The output plug of the AC cable is not
completely connected to the AC adaptor
jack. As shown in A, there is a gap.
A
ª Inserting the battery
1) Open the battery cover.
3) Close the battery cover.
≥Push A while sliding it.
ª How to turn on the power
While pressing the lock release button, set
PC
the mode dial to
,
or
.
≥Rotate the mode dial while at the same time
pressing in the lock release button A if
changing from OFF to another mode.
≥Align with the status indicator B.
A
B
2) Insert the battery until it clicks paying
attention to the direction of the battery.
B Push the center of the battery until it
locks.
A
ª How to turn off the power
Set the mode dial to OFF.
B
3) Close the battery cover.
10
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
ª Inserting/removing an SD card
1) Set the mode dial to OFF.
2) Open the LCD monitor and then open the
card slot cover.
ª Recording still pictures (JPEG)
1) Rotate the mode dial to select
.
2) Open the LCD monitor.
3) Press the PHOTO SHOT button halfway in
order to adjust focusing. (For auto
focusing only)
3) Insert/remove the SD card into/from the
card slot.
A
≥When inserting an SD card, face the label
side A upwards and press it straight in as
far as it goes.
4) Press the PHOTO SHOT button fully to
take the picture.
4) Securely close the card slot cover.
ª Recording motion pictures
1) Rotate the mode dial to select
.
2) Open the LCD monitor.
3) Press the recording start/stop button to
start recording.
4) Press the recording start/stop button
again to pause recording.
11
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
ª Motion picture playback
1) Rotate the mode dial to select
ª Still picture (JPEG) playback
.
1) Rotate the mode dial to select
.
2) Press the cursor button up and then left
2) Press the cursor button up and then right
to select the
playback) tab.
(motion pict ure
to select the
tab.
(still picture playback)
A
A
A Motion picture playback tab
A Still picture playback tab
3) Select the scene to be played back.
3) Select the file to be played back.
B
C
B
C
D
E
D
B Previous page
C Next page
B Previous page
C Next page
D Scene number
4) Press the cursor button.
D File number display
E Folder/file name
4) Press the cursor button.
5) Move the cursor button to operate.
1/;: Playback/Pause
5) Move the cursor button to operate.
6 (Move and hold): Review playback
5 (Move and hold): Cue playback
1/;: Slide show (playback of the still
pictures on the SD card in numerical
order) start/pause.
∫:
Stops the playback
and shows the
thumbnails.
E:
D:
∫:
Plays back the previous picture.
Plays back the next picture.
Stops the playback and shows the
thumbnails.
12
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Before using
Very clear high definition pictures
This unit is an AVCHD format video camera for recording highly detailed high definition images on an
SD card.
You can watch images in high-resolution HD video if you connect this unit and a high definition TV and
then play back the images. (l 80)
A
B
A High definition images (1440k1080)
Number of available scan lines 1080
B Standard images (720k480)
Number of available scan lines 480
High definition images
≥High definition images have more than approximately 2 times the number of available scan lines and
more than 4 times the number of pixels compared with standard images.
≥The still pictures above are images for explanation purposes.
ª What is the AVCHD?
This is a format for recording and playing back highly detailed high definition images.
Images are recorded based on the MPEG-4 AVC/H.264 codec for compressing images and audio is
recorded in Dolby Digital.
About the SDHC Memory Card supplied with this unit and the compatibility of the
recorded motion pictures
About the SDHC Memory Card (Be careful about the following.)
≥It is not compatible with devices other than those that support SDHC.
≥If you use the SDHC Memory Card in another device, use a device that is SDHC compatible. (l 26)
About the compatibility of the recorded motion pictures
≥They are not compatible with devices other than those that support the AVCHD. Refer to the
operating instructions of the device for details.
≥The recorded motion pictures cannot be played back in a device that is not compatible (does not
support the AVCHD).
≥There are some cases where the recorded motion pictures cannot be played back, even if the device
supports the AVCHD. In such cases, play the recorded motion picture with this unit instead.
Existing DVD recorders and DVD players that do not support the
AVCHD
13
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Watching high definition images
If you connect this unit and a high definition TV with a HDMI cable (optional) and then play back the
pictures, you can enjoy watching them in high definition.
A
B
A High definition TV
B HDMI cable (optional)
≥If you connect this unit to a TV that does not support high definition, the images will be standard
quality.
ª When connecting to a TV that does not have a HDMI terminal
Connecting with the component cable and the AV cable
Connecting with the AV cable
≥The pictures cannot be played in high definition when using the AV cable. They will be played back in
widescreen standard definition.
14
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Using the remote control for the TV for playback
TM
TM
If you connect this unit to a Panasonic TV compatible with EZ Sync (HDAVI Control ) with a HDMI
cable, you can use the remote control for the TV for playback. Refer to the operating instructions of the
TV for details.
A
B
A TV compatible with EZ Sync
B HDMI cable (optional)
ª Other linked operations
Turning the power on and off
If you turn off the power on the TV with the remote control for the TV, the power on this unit also turns
off.
Automatic input switching
If you connect with a HDMI cable and then turn on the power on this unit, the input channel on the TV
automatically switches to this unit’s screen. If the TV’s power is in standby status, it will turn on
automatically (if [Set] has been selected for the TV’s [Power on link] setting).
≥Depending on HDMI terminal of the TV, the input channel may not switch automatically. In this case,
use the remote control for the TV to switch input. (For details on how to switch input, please read the
operating instructions for the TV.)
15
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Listening in 5.1 channel surround sound
This unit has 5 internal microphones and a Dolby Digital 5.1 Creator so you can record sound with
presence that is even closer to the actual sound. The low bass area is sent to the 0.1 channel
subwoofer and you can playback sound with three-dimensional presence if you connect to a device that
Internal microphones
The 5 mounted internal microphones give
better directivity.
≥Far-away sounds can be recorded more
clearly with the zoom microphone function.
(l 53)
A
B
A AV amplifier with HDMI terminal
B HDMI cable (optional)
≥Refer to the operating instructions of the TV, AV amplifier, speakers etc. for details on how to connect.
≥If you record with an external microphone, the recording is in stereo 2 channel sound.
≥Optical digital cables cannot be used for the connection. Connect to an AV amplifier with an HDMI
terminal.
16
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Saving the data on the SD card
When the SD card is full or to prevent the data from being deleted, use the supplied software
(HD Writer Ver1.0E for SD1) to copy the data on the SD card to the hard disk of the computer.
A
A USB cable (supplied)
ª What you can do with HD Writer
[Copy to PC]
You can copy motion picture data and still picture data on an SD card to the hard disk of the computer.
[Write data to media]
You can copy motion picture data from the hard disk of the computer to an SD card or a DVD disc.
[Copy between media]
You can copy motion picture data from an SD card to a DVD disc or from a DVD disc to an SD card.
[Easy editing]
You can easily edit (split, merge, delete etc.) motion picture data that was copied to the hard disk of the
computer.
≥For details on how to use the software application, read the PDF operating instructions.
Important note
Do not insert a disc created with the supplied HD Writer Ver1.0E for SD1 in a device that does
not support the AVCHD format. It may no longer be possible to eject it. Also, the disc cannot
be played back on devices that do not support the AVCHD format.
ª The SD Media Storage
The SD Media Storage (VW-PT2ZP: supplied) is convenient if you are on the
move.
It is an extremely compact, lightweight and easy to carry HDD (hard disk).
≥If you insert an SD card with recorded motion pictures and still pictures in the SD
Media Storage, the data can easily be saved to the SD Media Storage by
pressing the copy button only.
≥You can save all the data from approximately ten 4 GB cards (one 4 GB card is supplied) to its 40 GB
HDD capacity.
17
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Accessories
Check the accessories before using this unit.
SDHC memory card (4 GB)
Battery pack
VW-VBG130
AC adaptor
VW-AD21PP
AC cable
K2CA2CA00029
DC cable
K2GJYYC00001
Remote control
N2QAEC000023
Button-type battery
CR2025
AV cable
K2KZ9CB00002
Component cable
K2KZ9DB00004
USB cable
K2KZ4CB00011
CD-ROM
SD Media Storage
VW-PT2ZP
≥The standard accessories for this unit are
the same as the standard accessories for
the Panasonic High Definition Video
Camera HDC-SD1 except for the SD Media
Storage.
18
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Parts identification and handling
1
5
2
3
1) Lens (LEICA DICOMAR)
2) Built-in flash for still pictures only (l 57)
3) Recording lamp (l 107)
4) White balance sensor/remote control sensor (l 25, 66)
5) Lens cover
6
7
11
12
13
14
8
9
10
6) Status indicator (l 32)
7) Mode dial (l 32)
8) LCD monitor open latch (l 24)
9) Menu button [MENU] (l 39)
10) Battery cable cover (l 22)
11) Cursor button (l 35)
12) Recording start/stop button (l 45)
13) Cooling fan (inlet)
14) Delete button [ ] (l 74, 76)
ª About the cooling fan
≥The cooling fan rotates to prevent the internal temperature rising. Take care not to cover the inlet and
outlet when using this unit.
19
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
15
16
17
15) Internal microphones (5.1 channel support)
16) Zoom lever [W/T] (In recording mode) (l 52)
Volume lever [sVOLr] (In playback mode) (l 70)
17) Photoshot button [
] (l 48)
18
18) Tripod receptacle (l 23)
19) Battery cover (l 29)
20
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
20
21
23
24
22
MIC
A/V COMPONENT
29
30
DC IN 9.3V
25 26 27
20) Power LCD button [POWER LCD] (l 42)
21) Reset button [RESET] (l 118)
22) LCD monitor (l 24)
Due to limitations in LCD production technology, there may be some tiny bright or dark spots on
picture.
23) Mode select switch [AUTO/MANUAL/FOCUS] (l 44, 63)
24) Card access lamp [ACCESS] (l 35)
25) Audio-video output terminal [A/V] (l 84, 86, 89)
≥Use the supplied AV cable only.
27) Microphone terminal [MIC]
≥A compatible plug-in powered microphone can be used as an external microphone.
≥When the unit is connected with the AC adaptor, sometimes noise may be heard depending on
the microphone type. In this case, please switch to the battery for the power supply and the noise
will stop.
28) DC input terminal [DC IN 9.3V] (l 31)
29) Card slot cover (l 34)
30) Card slot (l 34)
21
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
33
31
34
35
31) Speaker
32) Grip belt (l 23)
33) Outlet
34) USB terminal [ ] (l 90, 99)
35) HDMI terminal [HDMI] (l 81, 83, 87)
Battery cable cover
Open the battery cable cover when you use the battery pack holder kit (VW-VH04; optional¢).
1 Open the battery cover.
3 Attach the battery pack holder kit.
≥Read the operating instructions of the battery
pack holder kit for details on how to use it.
4 Close the battery cover.
A
≥The cable of the battery pack holder kit can
pass through the hole.
≥Push A while sliding it.
≥Keep the battery cable cover closed when
using this unit normally.
2 Open the battery cable cover.
¢ The optional accessories are the same as for
the Panasonic High Definition Video Camera
HDC-SD1.
22
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Using grip belt
Lens hood
Adjust the length of the grip belt so that it fits your
hand, and hold it properly.
Rotate the lens hood
counter-clockwise A to remove it. In
order to attach it, place into slot B,
and then rotate it clockwise C.
1 Flip the belt.
A
B
C
2
Put your hand through the grip belt.
Tripod receptacle
The tripod receptacle is a hole used to mount a
tripod for the unit. (For details on mounting the
tripod, refer to the operating instructions for the
tripod.)
≥You cannot use a tripod with a fixed tripod pin.
A Rubber grip
1 Loosen the belt.
2 Put your hand through the belt as far as it
goes.
A Camera base
B Screw for mounting the unit
C Tripod pin
≥Slip your hand through the belt as far as it
goes so that your fingers will grip the
rubber area firmly.
≥You can perform operations easily using the
remote control when the tripod is used. (l 24)
≥The battery cover cannot be opened when the
tripod is used. Insert the battery before
attaching this unit to the tripod. (l 29)
3 Replace the belt.
≥Tighten up the belt so that your hand
remains firmly in place.
23
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Using the LCD monitor
Using the remote control
You can record the image while viewing it on the
LCD monitor.
1
START/
PHOTO
SHOT
EXT
STOP
DISPLAY
1 Place your finger on LCD monitor
open latch and pull the LCD
monitor out in the direction of the
arrow.
7
8
2
3
DATE/
TIME
ZOOM
VOL
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
4
MENU
9
5
6
ENTER
≥It can open up to 90o.
10
2 Adjust the angle of the LCD
monitor as desired.
A
1) Photoshot button [
]*
2) On-screen display button [EXT DISPLAY]
(l 80)
5) Delete button [ ]*
B
6) Direction buttons [3,4,2,1] (l 40)
7) Recording start/stop button [START/
STOP]*
8) Zoom/volume buttons [ZOOM, VOL]*
9) Menu button [MENU]* (l 40)
10) Enter button [ENTER] (l 40)
* means that these buttons function in the
same manner as the corresponding
buttons on the unit.
≥It can be rotated 180° towards the lens A
and 90° towards the opposite direction B.
≥The brightness and color level of the LCD
monitor can be adjusted. (l 42)
≥The unit may be damaged or fail if the LCD
monitor is forcibly opened or rotated.
≥Check that the terminal cover is closed before
closing the LCD monitor.
24
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
ª Install a button-type battery
Install the supplied button-type battery in the
remote control before using it.
ª Remote control usable range
The distance between the remote control and the
unit’s remote control sensor A: Within approx.
5 m (16 feet)
Angle: Approx. 10o up and 15o down, left, and
right
1 While pressing the stopper A,
pull out the battery holder.
A
A
2 Set the button-type battery with
its (i) mark facing upward and
then put the battery holder back
in place.
≥The remote control is intended for indoor
operation. Outdoors or under strong light, the
unit may not operate properly even within the
usable ranges.
Concerning the button-type battery
≥When the button-type battery runs down,
replace it with a new battery (part number:
CR2025). The battery should normally last
about 1 year, however this depends on how
frequently the unit is used.
≥Keep the button-type battery out of the reach of
children.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
Replace battery with Panasonic PART NO.
CR2025 only. Use of another battery may
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away
from children.
Do not recharge, disassemble or dispose of in
fire.
25
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
Cards that you can use with this unit
Card
Card type
Capacity
SD Memory Card
32 MB, 64 MB,
128 MB
256 MB, 512 MB,
1 GB, 2 GB
8 MB, 16 MB
4 GB
Cannot be
guaranteed in
operation.¢
Cannot be
used.
Refer to “About SD cards that you can use
for motion picture recording”.
recording
Still picture
recording
Can be used.
¢The recording may suddenly stop during motion picture recording depending on the SD card you use.
(l 46)
This unit (an SDHC compatible device) is compatible with both SD Memory Cards and SDHC
Memory Cards. You can use SDHC Memory Cards on devices that are compatible with them.
However, you cannot use SDHC Memory Cards on devices that are only compatible with SD
Memory Cards. (When using an SDHC Memory Card on another device, always read the operating
instructions of that device.)
ª About SD cards that you can use for motion picture recording
We recommend using SD Memory cards and SDHC Memory cards conforming to Class 2 or higher of
the SD Speed Class Rating or the following SD cards made by Panasonic for motion picture recording.
Pro High Speed Super High Speed
SD Memory Card SD Memory Card SD Memory Card
High Speed
SDHC Memory
Card
Card type
256 MB
512 MB
—
RP-SDH256
—
—
—
RP-SDK512
RP-SDH512¢
RP-SDR512
RP-SDQ01G¢
RP-SDR01G
1 GB
2 GB
RP-SDK01G
RP-SDH01G¢
—
RP-SDQ02G¢
RP-SDR02G
RP-SDK02G
—
—
—
—
4 GB
—
RP-SDR04G
¢No longer made.
≥Operation in motion picture recording is not guaranteed with an SD card memory from 32 MB to 4 GB
except the cards above. (The recording may suddenly stop during motion picture recording.)
≥For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are
referred to as the “SD card”.
≥This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥If you wish to use Memory Cards that are 4 GB, SDHC Memory Cards only can be used.
26
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using
the SDHC logo are not based on SD Memory
Card Specifications.
≥Use this unit to format SD cards. If an SD card
is formatted on other products (such as a
computer), the time spent for recording may
become longer and you may not be able to use
the SD card. (l 79) (Do not format it on a PC
etc.)
≥When the write-protect switch A on SD Card is
locked, no recording, deletion or editing will be
possible on the card.
A
4
≥Keep the Memory Card out of reach of children
to prevent swallowing.
≥A MultiMediaCard cannot be used on this unit.
ª
(SD Speed Class
Rating Class 2)
This indicates a Class 2 rating in the high speed
standards (SD Speed Class) stipulated by the
SD Card Association for high speed writing
between SD compatible products and SD
Memory cards.
If you use a Class 2 card compatible with the SD
Speed Class in an SD compatible product, you
can obtain stable recording by using an SD card
conformed with Class 2 or more.
ª Handling precautions
≥Do not expose the terminals of the card to
water, garbage or dust.
≥Do not place in the following areas:
– In direct sunlight.
– In very dusty or humid areas.
– Near a heater.
– Locations susceptible to significant
difference in temperature (condensation can
occur).
– Where static electricity or electromagnetic
waves occur.
≥To protect cards, return them to their cases
when you are not using them.
27
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
ª Charging lamp
Lights up: Charging
Setup
Goes off: Charging completed
Flashing: Make sure that the terminals of the
battery or the AC adaptor are not
exposed to dirt, foreign objects or
dust, then reconnect them properly.
Disconnect the AC cable from the AC
outlet when you remove dirt, foreign
battery or the AC adaptor.
Charging the battery
When this unit is purchased, the battery is not
charged. Charge the battery before using this
unit.
≥Connect the battery to an AC adaptor to
recharge it.
The battery cannot be recharged by simply
inserting it into the unit.
≥If the DC cable is connected to the AC
adaptor, then the battery will not charge.
Remove the DC cable from the AC adaptor.
≥The Panasonic battery that can be used
with this unit is VW-VBG130. Other
Panasonic batteries will not work. (l 30)
If the charging lamp is still flashing,
something may be wrong with the
battery or AC adaptor. Contact your
dealer.
≥Battery charging time (l 30)
≥We recommend using Panasonic batteries
(VW-VBG130).
A
≥If you use other batteries, we cannot guarantee
the quality of this product.
1 Connect the AC cable to the AC
adaptor and the AC outlet.
≥Remove the DC cable beforehand.
2 Put the battery on the battery
mount by aligning the mark, and
then securely plug it in.
≥The output plug of the AC cable is not
completely connected to the AC adaptor
jack. As shown in A, there is a gap.
28
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Inserting/removing the battery
Removing the battery
1 Open the battery cover.
Inserting the battery
1 Open the battery cover.
≥Push A while sliding it.
2 Remove the battery.
≥Move A in the direction of the arrow to
unlock it and then remove the battery.
A
2 Insert the battery until it clicks
paying attention to the direction
of the battery.
B Push the center of the battery until it
locks.
A
3 Close the battery cover.
B
3 Close the battery cover.
≥Be sure to set the mode dial to OFF and check
that the status indicator is off before removing
the battery.
≥The battery cover opens up to 180o.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
29
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Charging time and recordable time
ª About batteries that you can use for this unit
The Panasonic battery that can be used with this unit is VW-VBG130.
VW-VBG130 comes with a function to check whether the battery and unit can be safely used together.
≥Batteries made by other companies which have been certified by Panasonic may be used with this
unit, but we offer no guarantee as to the quality, performance or safety of such batteries.
≥In order to safely use the unit, we recommend that you use genuine Panasonic batteries which have
been subject to our quality control process.
≥We cannot accept any liability whatsoever for damages to the unit or accidents caused by
non-genuine Panasonic batteries (including those that have been certified by Panasonic).
≥Exercise care when purchasing batteries. Many fake or imitation batteries have been found among
those sold at unusually low prices and those which customers cannot check for themselves before
purchasing.
ª Charging time
The times shown in the tables below are for when the temperature is 25 oC (77 oF) and the humidity is
60%. If the temperature is higher or lower than 25 oC (77 oF), the charging time will become longer.
Battery model number
Voltage/capacity
Charging time
Supplied battery/
VW-VBG130 (optional)
7.2 V/1320 mAh
2 h 20 min
≥The charging time shown in the table are approximations.
≥“2 h 20 min” indicates 2 hours 20 minutes.
≥When you charge a battery that has not been used for long time, the charging time will become
longer.
ª Recordable time
≥The times shown in the table below are for when the temperature is 25 oC (77 oF) and the humidity is
60%. These times are approximations.
Maximum continuously
Battery model number
Voltage/capacity
recordable time
Supplied battery/
VW-VBG130 (optional)
7.2 V/1320 mAh
1 h 5 min
≥The recordable time shown in the table are approximations.
≥“1 h 5 min” indicates 1 hour 5 minutes.
≥The recordable times will vary depending on the status of use. These times are approximations.
≥The recordable time will become shorter in the following case:
– The recordable time will become shorter when you use this unit with the LCD monitor lit up by
pressing the POWER LCD button.
≥The batteries heat up after use or charging. This unit will also heat up while being used. This is not a
malfunction.
≥Be aware that the operating time of the battery will become shorter in low temperatures. We
recommend charging a spare battery for use when recording.
30
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
ª About the remaining battery
Connecting to the AC outlet
≥Even if the battery is inserted in this unit, it
capacity indication
The remaining battery capacity is displayed in
minutes when using the Panasonic battery that
you can use for this unit. It may take time to
display the remaining battery capacity.
will not charge.
DC IN 9.3V
30min
≥The display changes as the battery capacity
reduces.
#
#
#
#
.
If there is less than 3 minutes remaining, then
will become red. If the battery
discharges, then (
) will flash.
1 Connect the AC cable to the AC
≥The remaining battery capacity may not be
displayed correctly where the temperature is
low or high or if the battery was not used for a
long period of time.
To correctly display the remaining battery
capacity, recharge the battery, discharge it and
then charge it again. (Even if this operation is
performed, it may not be possible to display the
remaining battery capacity correctly if the
battery was used for a long period of time
where the temperature is low or high or if the
battery was repeatedly charged.)
≥The times of remaining battery capacity
indication will vary depending on the status of
use. These times are approximations.
≥When turning the mode dial to switch modes,
the time indication will turn off in order to
recalculate the remaining battery capacity time.
≥When using batteries made by other
companies, the remaining battery capacity will
not be shown.
adaptor.
2 Connect the DC cable to the AC
adaptor.
3 Open the terminal cover on this
unit and connect the DC cable to
the DC input terminal
[DC IN 9.3V].
≥Do not use the AC cable with any other
equipment as it is designed only for this
unit. Do not use the AC cable from other
equipment with this unit.
≥Put the battery on the AC adaptor to charge it.
(l 28)
≥While the DC cable is connected to the AC
adaptor, the battery will not charge.
31
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Selecting a mode
(Turning the unit on/off)
Rotate the mode dial to switch to recording,
playback, PC connection or power OFF.
≥Rotate the mode dial slowly.
How to turn off the power
Set the mode dial to OFF.
How to turn on the power
While pressing the lock release
button, set the mode dial to
,
The status indicator goes off and the power turns
off.
PC
or
.
≥Rotate the mode dial while at the same time
pressing in the lock release button A if
changing from OFF to another mode.
≥Align with the status indicator B.
set to OFF.
Recording mode (l 45, 48)
Use this to record motion pictures and
still pictures on an SD card.
B
Playback mode (l 68, 72)
Use this to play back motion pictures
and still pictures recorded on an SD
card.
A
PC Connection mode (l 99)
Use this to import motion pictures and
The status indicator lights and the power turns
on.
PC
still pictures recorded on an SD card
with a computer by using HD Writer
Ver1.0E for SD1 etc.
≥The lens cover opens in recording mode.
≥When the unit is turned on for the first time, a
message asking you to set the date and time
will appear. Select [YES] and set the date and
time. (l 41)
OFF The power turns off.
≥Do not forcefully rotate the mode dial.
32
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Quick start
When quick start is ON the battery power is still
being consumed, even when the LCD monitor is
closed.
This unit will resume recording/pause mode
about 1.7 seconds after the LCD monitor is
reopened.
Turning the power on and off with
the LCD monitor
The power can be turned on and off with the LCD
monitor when the mode dial is set to
.
ª To turn on the power
Open the LCD monitor.
≥When in quick start standby mode about
70% of the power used in recording pause
mode is being consumed, so the recording
time will be reduced.
≥This is only activated in the following case.
A
– When the mode dial is set to
SD card is inserted.
and an
1 Press the MENU button, then
select [SETUP] # [QUICK START]
# [ON] and press the cursor
button.
The status indicator A lights and the power turns
on.
ª To turn off the power
Close the LCD monitor.
A
2 Close the LCD monitor while the
mode dial is set to
.
The status indicator A goes off and the power
turns off. (If [QUICK START] (l 33) is set to
[ON], the unit goes into quick start standby mode
and the status indicator lights green.)
≥The power will not turn off while recording a
motion picture even if the LCD monitor is
closed.
A
Set the mode dial to OFF when this unit is not
being used.
The status indicator A lights green and the
unit goes into quick start standby mode.
≥The lens cover does not close.
33
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3 Open the LCD monitor.
Inserting/removing an SD
card
A
Be sure to set the mode dial to OFF before
inserting/removing an SD card.
If the SD card is inserted or removed while the
power is on, this unit may malfunction or the
data recorded on the SD card may be lost.
The status indicator A lights red and the unit
is put into recording pause approx.
1.7 seconds after it is turned on.
1 Set the mode dial to OFF.
≥Check that the status indicator has gone
off.
ª To cancel Quick start
2 Open the LCD monitor and then
Press the MENU button, then select [SETUP]
# [QUICK START] # [OFF] and press the
cursor button.
open the card slot cover.
≥The status indicator goes off, the lens cover
closes and the power turns off if the mode dial
is set to OFF while the unit is in quick start
standby mode.
≥The status indicator goes off and the power
turns off if quick start standby mode continues
for approx. 5 minutes.
3 Insert/remove the SD card into/
from the card slot.
≥Quick start standby mode is canceled, the
status indicator goes off and the power turns off
in the following cases.
– the mode dial is switched
– the battery is removed
≥When this unit is quick-started with the white
balance on automatic, it may take some time
until the white balance is adjusted if the scene
being recorded has a light source different from
function is used, however, the white balance of
the scene last recorded is retained.)
≥When this unit is quick-started, the zoom
magnification becomes 1k and the picture size
may differ from what it was before quick start
standby mode.
A
≥When inserting an SD card, face the label
side A upwards and press it straight in as
far as it goes.
≥When removing the SD card, press the
center of the SD card and then pull it
straight out.
4 Securely close the card slot
≥If [POWER SAVE] (l 107) is set to
[5 MINUTES] and the unit automatically goes
into quick start standby mode, close the LCD
monitor and then open it again.
cover.
34
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
ª Concerning the SD card
SD card.
How to use the cursor button
This unit has a cursor button A for selecting
functions, performing operations etc. so it is easy
to operate this unit with one hand.
≥Electrical noise, static electricity or the failure of
this unit or the SD card may damage or erase
the data stored on the SD card. Save important
data recorded on this unit to a PC using the
USB cable (supplied), HD Writer Ver1.0E for
SD1 etc. (l 102) (We recommend using
HD Writer Ver1.0E for SD1 to acquire data
recorded on this unit.)
T
X
E
N
NEXT
3
/
1/3
A
B
≥When using an SD card on which data has
been written many times, the remaining time
left for recording may be reduced. (l 46)
B Operating the operation icons and menu
screens that are displayed
ª Card access lamp
Basic operations
The following describes operations on the menu
screen and selection of files on the thumbnail
view screen etc.
Move the cursor button up, down,
left, or right to select an item or
scene, and then press the cursor
button to set it.
≥When this unit accesses the SD card (reading,
recording, playback, erasing etc.), the access
lamp lights up.
≥If the following operations are performed when
the access lamp is lit, then the SD card or the
recorded data may be damaged or this unit
may malfunction.
1
5
3
4
2
– Opening the card slot cover and removing
the SD card
– Operating the mode dial
– Removing the battery or disconnecting the
AC adaptor
1 Select by moving up.
2 Select by moving down.
3 Select by moving left.
4 Select by moving right.
5 Press the cursor button to set the item.
≥Menu screen operations (l 39)
35
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Operations during recording
Operations during playback
¬ Rotate the mode dial to select
1 Move the cursor button up,
¬ Rotate the mode dial to select
.
.
1 Press the center of the cursor
button, and icons will be
down, left or right to select the
scene to be played back and
press the cursor button.
displayed on the screen.
≥The indication disappears when the center
of the cursor button is pressed again.
≥The indication changes each time the
cursor button is moved down.
2 Move the cursor button up, left or
≥The selected scene is played back on the
full screen.
right to select an item.
≥The operation icon is automatically
displayed on the screen.
2 Move the cursor button up,
down, left or right to operate.
≥The operation icon appears or disappears
each time the center of the cursor button is
pressed.
36
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
About the operation icons displayed in each mode
Recording mode
Icon
Direction
Function
Backlight compensation
Page
3
2
1
3
2
1
3
2
1
54
54
39
55
56
56
57
57
58
(1/3)
(2/3)
(3/3)
Fade
Help mode
MagicPix
Soft skin mode
Tele macro
Self-timer
Flash
Ø
ß
Red eye reduction
Set the AUTO/MANUAL/FOCUS switch to MANUAL.
3
2
1
White balance
65
66
66
In manual mode
[MANUAL] (4/4)
Iris or gain value
Shutter speed
Set the AUTO/MANUAL/FOCUS switch to FOCUS.
In manual focus
mode [FOCUS]
(5/5)
21
Manual focus adjustment
64
≥The shaded operation icons are not displayed while recording.
≥About switching between AUTO and MANUAL (l 44)
37
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Playback mode ( In motion picture playback)
Icon
Direction
Function
Page
68
1/;
∫
3
4
Playback/pause
Stop playback and show thumbnails
Rewind (during playback)
68
6
2;
5
;1
68
2
1
Reverse slow/frame playback (during pause)
Fast forward (during playback)
69
68
Forward slow/frame playback (during pause)
69
Playback mode (
In still picture playback)
Icon
1/;
∫
Direction
Function
Slide show start/pause
Page
73
3
4
2
1
Stop playback and show thumbnails
Playback previous picture (during pause)
Playback next picture (during pause)
73
E
73
D
73
38
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Using the menu screen
Refer to “Menu list” (l 105) for information about
Help mode
The help mode explains the operation icons
displayed when the AUTO/MANUAL/FOCUS
switch is set to AUTO in recording mode.
the menus.
1 While stopped, press the MENU
button.
¬ Rotate the mode dial to select
.
1 Press the cursor button to
display the icon.
≥The menu displayed differs depending on
the position of the mode dial.
≥Do not switch the mode dial when the
menu is displayed.
2 Move the cursor button right to
select [
].
2 Move the cursor button up or
down in order to select the
desired top menu A.
A
3 Move the cursor button up, left or
right to select the desired icon.
3 Move the cursor button right or
press the cursor button.
B
An explanation of the selected icon scrolls at
the bottom of the screen.
≥The indication changes each time the
cursor button is moved down.
To exit the help mode
≥The submenu B is displayed.
Press the MENU button or select [END].
≥When the help mode is used, functions cannot
be set.
≥When the help mode is used, motion pictures
and still pictures cannot be recorded.
39
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
To exit the menu screen
Press the MENU button.
4 Move the cursor button up or
down in order to select the
submenu item.
C
≥The menu screen does not appear during
recording or playing. You cannot start other
operations while the menu screen appears.
Operating with remote control
C Current settings on menus
The menu screen transition is the same as when
the buttons on the main unit are used.
5 Move the cursor button right or
press the cursor button.
1 Press the MENU button.
MENU
ENTER
2 Select a menu item.
MENU
6 Move the cursor button up or
down in order to select the
desired item.
ENTER
≥Use the direction buttons (3,4,2,1) and
ENTER button in place of the cursor button
on the main unit.
3 Press the MENU button to exit
7 Press the cursor button to enter
the menu screen.
the selection.
MENU
ENTER
To get back to the previous screen
Move the cursor button left.
40
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Changing the date and time display style
Press the MENU button, then select [SETUP] #
[DATE/TIME] # desired display style and press
the cursor button.
≥You can also show or change the date and time
display by repeatedly pressing the DATE/TIME
button on the remote control.
Setting date and time
When the unit is turned on for the first time, a
message asking you to set the date and time will
appear.
≥Move the cursor button up or down to select
[YES], press the center of the cursor button and
then perform steps 2 and 3 below to set the
date and time.
[DATE]
[D/T]
If the screen shows the incorrect date and time,
then adjust it.
DEC 15 2007
DEC 15 2007 3:30PM
¬ Rotate the mode dial to select
.
[OFF]
1 Press the MENU button, then
select [BASIC] # [CLOCK SET] #
[YES] and press the cursor
button.
Changing the display style
Press the MENU button, then select [SETUP] #
[DATE FORMAT] # desired display style and
press the cursor button.
Display style
[Y/M/D]
Screen display
2007.12.15
2 Move the cursor button left or
right to select the item to be set.
Then, move the cursor button up
or down to set the desired value.
[M/D/Y]
DEC 15 2007
15.12.2007
[D/M/Y]
≥The date and time function are driven by a
built-in lithium battery.
≥Make sure to check the time before recording.
≥If the time display becomes [- -], the built-in
lithium battery has run down. Use the following
steps to charge the battery. When you turn on
the power for the first time after charging, a
message asking you to set the date and time
will appear. Select [YES] and set the date and
time.
≥The year will change as follows:
2000, 2001, ..., 2039, 2000, ...
≥The 12-hour system is used to display the
time.
3 Press the cursor button to enter
To recharge the built-in lithium battery:
If you connect the AC adaptor or insert the
battery in this unit, the built-in lithium battery will
be recharged. Leave the unit as it is for approx.
24 hours and the battery will save the date and
time for approx. 6 months. (The battery is still
being recharged even if the mode dial is set to
OFF.)
the selection.
≥The clock function starts at [00] seconds
when the cursor button is pressed.
≥After pressing the MENU button to finish
the setting, check the date and time
display.
41
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
≥After adjustments are made if no operations
are performed for about 2 seconds, the bar will
disappear.
≥Press the MENU button to exit the menu
screen.
Switching the language
You can switch the language on the screen
display or the menu screen.
1 Press the MENU button, then
select [LANGUAGE] and press
the center of the cursor button.
[BRIGHTNESS]: Brightness of the LCD monitor
[COLOR]:
Color level of the LCD monitor
≥These settings will not affect the images
actually recorded.
ª In order to increase the
brightness of the entire LCD
monitor
Press the POWER LCD button.
2 Select [English] and press the
center of the cursor button.
POWER LCD
Adjusting LCD monitor
Adjusting the brightness and the
color level of the LCD monitor
The [
monitor.
] indication appears on the LCD
≥Press the POWER LCD button if the
surroundings are bright and the LCD monitor is
difficult to see. The entire LCD monitor will
become approx. twice as bright as usual.
1 Press the MENU button, then
select [SETUP] # [LCD SET] #
[YES] and press the cursor
button.
≥When the POWER LCD button is pressed
again, the [
] indication disappears and the
original brightness is restored.
≥This will not affect the images to be recorded.
≥If you turn on the unit when the AC adaptor is
used, this function will automatically be
activated.
2 Move the cursor button up or
down to select the item to be
adjusted. Then, press the cursor
button and move the cursor
button left or right to make the
adjustment.
≥This function cannot be used in PC Connection
mode.
The bar display moves.
42
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording
Before recording
First, format the SD card if one which has been used on another device is going to be used for the first
time on this unit. (l 79) When the SD card is formatted, all of the recorded data is deleted. Once the
data is deleted, it cannot be restored. Copy valuable data onto a PC or other device before proceeding
with the formatting.
We recommend using HD Writer Ver1.0E for SD1 to import data recorded on this unit. (l 102)
Basic camera positioning
1
3
5
2
B
C
4
D
A
6
E
1 Hold the unit with both hands.
2 Put your hand through the grip belt. Place your fingers on the rubber grip A and grasp the unit
firmly.
3 Do not cover inlet B or outlet C of the cooling fan with your hand as it will prevent heat release.
If heat builds up inside the unit, it could be damaged.
4 Do not cover the microphones D or the sensors E with your hands.
5 Keep your arms near your body.
6 Slightly open your legs.
≥When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will
become dark in the recording.
≥When recording, make sure your footing is stable and there is no danger of colliding with another
person or object.
43
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
ª About auto mode
Auto Ground-Directional
Standby (AGS)
Set the AUTO/MANUAL/FOCUS switch to
AUTO, and color balance (white balance) and
focusing will be adjusted automatically.
This function prevents unnecessary recording
when you forget to pause recording and walk
with the unit tilted upside down while recording
continues.
AUTO
MANUAL
FOCUS
– Automatic white balance (l 123)
– Auto focus (l 124)
Depending on the brightness of the subject etc.,
the aperture and shutter speed are automatically
adjusted for an optimum brightness.
(The shutter speed is adjusted to a maximum of
1/250 in recording mode.)
automatically depending on light sources or
scenes. If so, manually adjust these settings.
– Scene mode setting (l 63)
– White balance setting (l 65)
– Shutter speed setting (l 66)
≥If the unit continues to be tilted upside down
from the normal horizontal position while
recording motion pictures, it is automatically put
into recording pause.
– Iris/gain value setting (l 66)
– Manual focus setting (l 64)
Turning the AGS function on/off
¬ Rotate the mode dial to select
Press the MENU button, then select
[VIDEO] # [AGS] # [ON] or [OFF]
and press the cursor button.
.
≥This function’s default setting is [OFF].
≥The AGS function may activate and cause the
unit to pause the recording if you are recording
a subject right above or right below you. In
these cases, set [AGS] to [OFF] then continue
the recording.
≥Use the recording start/stop button to pause
the recording. The AGS function is only a
backup function for when you forget to pause
the recording.
≥The time it takes the unit to be put into
recording pause after being tilted upside down
varies depending on the operating conditions.
44
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
To end the recording
Press the recording start/stop button again to
pause recording.
Recording motion pictures
Record motion pictures on an SD card.
≥Use an SD card that can be used for motion
picture recording. (l 26)
≥This unit records high definition images that are
compatible with the 16:9 aspect ratio of a
wide-screen TV.
1 Rotate the mode dial to select
≥[¥] and [;] are red during recording. Do not
move this unit until [;] is green.
.
≥The images recorded between pressing the
recording start/stop button to start recording
and pressing it again to pause recording
become one scene.
≥When about 5 minutes have passed without
any operation in recording pause, the unit
automatically turns off to prevent the battery
from running down. When you want to use the
unit, turn it on again.
The lens cover opens automatically.
This setting can also be set to [OFF]. (l 107,
[POWER SAVE])
2 Open the LCD monitor.
3 Press the recording start/stop
button to start recording.
≥While recording is in progress, the
recording will not stop even if the LCD
monitor is closed.
45
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
ª Screen indications in the
ª When recording stops suddenly
recording mode
during motion picture recording
When using an SD card other than one that can
be used for motion picture recording (l 26), the
recording may stop suddenly. At this time, the
following message appears.
When motion pictures are to be recorded, use a
Panasonic SD card or another SD card which
can be used to record motion pictures. (l 26)
A
B
C
A Recording mode
B Remaining time left for recording
(When the remaining time is less than
1 minute, [R0min] flashes red.)
C Recording time elapsed
REC STOPPED.
NOW WRITING.
≥Maximum number of recordable scenes: 999 (It
may not be possible to record 999 scenes even
if there is available memory on the SD card.)
≥Maximum number of recordable scenes with
different dates: 99
(In some cases, scenes shot on the same day
will be recorded with different dates. (l 71))
≥SD cards with more than the maximum scenes
or different dates cannot be used with this unit.
≥Sound is recorded from the internal
INCOMPATIBLE CARD.
PLEASE CHECK CARD.
Even if you use an SD card that can be used
for motion picture recording (l 26), this kind
microphones on the top of this unit. Take care
not to block this microphone.
The data on the card has been written many
times and the data writing speed has reduced.
We recommend formatting the SD card being
used. (l 79) When an SD card is formatted, all
the data recorded on it will be deleted so copy
valuable data to the PC prior to formatting.
(l 102) (When acquiring data recorded on this
unit, we recommend using HD Writer Ver1.0E for
SD1 to acquire it. (l 102))
≥Put the unit in pause mode when connecting or
disconnecting an external microphone with the
MIC terminal. If an external microphone is
connected or disconnected while recording, the
audio will not be recorded properly.
≥Each time the unit is put into recording pause,
the counter display will be reset to “0h00m00s”.
the battery or disconnect the AC adaptor. Also
do not remove the SD card while the card
access lamp is lit. If you do either of the above,
the scene recovery message is displayed and
the recovery operation will begin when the SD
card is next inserted or the power is turned
back on. (l 112)
46
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording modes/recordable time available for the motion
picture
Switch the picture quality of the motion pictures to be recorded.
¬ Rotate the mode dial to select
.
Press the MENU button, then select [VIDEO]
# [REC MODE] # desired item and press the
cursor button.
Approximate recording times of motion pictures per SD card made by Panasonic
SD card
memory
:
HF
HF
HN
HE
Motion pictures can be recorded with the
highest picture quality.
256 MB
512 MB
2 min
5 min
3 min
7 min
5 min
10 min
:
HN
Motion pictures can be recorded with normal
picture quality.
1 GB
10 min
15 min
22 min
2 GB
4 GB
20 min
40 min
30 min
1 h
45 min
:
HE
Motion pictures can be recorded for longer.
1 h 30 min
≥The recordable time shown in the table are approximations.
≥Motion pictures can be recorded with the high definition picture quality.
≥This unit records in CBR in
mode. CBR is an abbreviation for Constant Bit Rate. CBR recording
HF
≥This unit records in VBR in mode. VBR is an abbreviation for Variable Bit Rate.
/
HN HE
VBR recording automatically varies the bit rate (amount of data in a fixed time) depending on the
subject being recorded. This means if a subject with sharp movements is recorded, the recording time
is reduced.
≥Sound is recorded with the Dolby Digital 5.1 Creator. (when recording with the built-in microphone)
≥Recordable time using the battery (l 30)
≥8 MB and 16 MB SD cards cannot be used for motion picture recording.
≥If the write protection switch on the SD card is set to LOCK, it cannot be used for recording. (l 27)
≥If an SD card is recorded on or erased many times, it may no longer be possible to record motion
pictures even if there is available memory on the SD card. In this case, after saving the data on PC,
format the SD card.
Mosaic-pattern noise may appear on a playback image in the following cases.
≥When there is a complicated pattern in the background
≥When the unit is moved too much or too fast
≥When a subject with sharp movements has been recorded
(Particularly if it has been recorded in
mode.)
HE
47
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording still pictures
(JPEG)
Record the still picture on an SD card.
≥This number of recording pixels for still pictures
is compatible with the 16:9 aspect ratio of a
wide-screen TV. They are recorded at
1920k1080.
A
B
A Focus indication
± (The white lamp flashes.):
Focusing
1 Rotate the mode dial to select
¥ (The green lamp lights up.):
When in focus
No mark:
.
When focusing is unsuccessful.
B Focus area
4 Press the PHOTO SHOT button
fully to take the picture.
The lens cover opens automatically.
2 Open the LCD monitor.
3 Press the PHOTO SHOT button
halfway in order to adjust
focusing. (For auto focusing
only)
≥In order to take better still pictures, the
screen will brighten when recording.
To record still pictures clearly
≥When zooming in on the subject with a
magnification of 4k or higher, it is difficult to
reduce the slight shaking from holding this unit
by hand. We recommend decreasing the zoom
magnification and approaching the subject
when recording.
≥When recording still pictures, hold the unit
firmly with your hands and keep your arms
unit.
≥You can record stable pictures without shaking
by using a tripod and the remote control.
The shutter speed and the iris/gain value are
fixed and the unit focuses on the subject
automatically.
≥If you set [O.I.S.] (l 59) to [ON], then the
image stabilizer function will be more
effective. ([
stabilizer) will be displayed.)
] (MEGA optical image
MEGA
≥For information about the number of
recordable still pictures on an SD card
(l 51)
≥The sound cannot be recorded.
≥If the write protection switch on the SD card is
set to LOCK, it cannot be used for recording.
≥The PHOTO SHOT button on the remote
control cannot be pressed halfway.
48
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥If the [PICT. QUALITY] is set to [
],
ª About the focus indication
mosaic-pattern noise may appear on a
playback image depending on the picture
content.
≥The focus indication indicates the status of the
auto focus.
≥The focus indication does not appear in manual
focus mode.
≥While this unit accesses the SD card (
is
displayed/the card access lamp is lit), do not
perform the following operations. The SD card
or the recorded data may be damaged.
– Turn the unit off.
– Open the card slot cover and remove the SD
card.
≥Focus on a subject manually when it is not
easily focused automatically.
≥You can record still pictures on the card even if
the focus indication does not appear, but
pictures may be recorded without being
focused.
≥The focus indication does not appear or has
difficulty displaying in the following cases.
– When the zoom magnification is high.
– When the unit is shaken.
– When the subject is moving.
– When the subject stands in front of a light
source.
– Operate the mode dial.
≥Other products may degrade or not playback
still pictures recorded on this unit.
≥The edges of still pictures recorded on this unit
with a 16:9 aspect ratio may be cut at printing.
Check the printer or photo studio before
printing.
– When close subjects and far subjects are
included in the same scene.
– When the scene is dark.
– When there is a bright part in the scene.
– When the scene is filled with only horizontal
lines.
ª About the screen indications
only when the PHOTO SHOT
button is pressed halfway
– When the scene lacks contrast.
– When recording motion pictures
– When the MagicPix function is used.
2.1Ｍ
MEGA
750
ª Concerning the focusing area
When there is a contrasting object ahead or
behind the subject in the focus area, the subject
may not be focused. If so, move the contrasting
object out of the focus area.
A BC D E F G H
A Flash (l 57)
B Flash level (l 58)
C Red eye reduction (l 58)
D Quality of still pictures
≥Even when it is still difficult to focus, adjust the
focus manually.
E Size of still pictures
F Remaining number of still pictures
(Flashes in red when [0] appears.)
G Card indication (l 108)
≥The focusing area is not displayed when the
digital zoom (more than approx. 12k) is used.
H MEGA optical image stabilizer (l 59)
49
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Switching the shutter effect on/off
About simultaneous recording
(recording still pictures while
recording motion pictures)
You can add a shutter sound when recording still
pictures.
Press the MENU button, then select
[PICTURE] # [SHTR EFFECT] #
[ON] or [OFF] and press the cursor
button.
You can record still pictures even while recording
motion pictures.
While recording motion pictures,
press the PHOTO SHOT button fully
(press to the bottom) to take the
picture.
≥This function’s default setting is [ON].
≥This function does not work during motion
picture recording.
≥This function is not activated if the
PHOTO SHOT button is pressed halfway.
≥The screen indications that appear only when
the PHOTO SHOT button is pressed halfway
will be displayed. (l 49) However, the
remaining number of still pictures will not be
displayed.
≥The picture quality is different from normal still
picture recording because priority is given to
the motion picture recording. We recommend
pausing the motion picture recording to record
a still picture with better picture quality.
50
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Picture Quality/Approximate
Number of Recordable
Pictures on an SD Card
Approximate Number of
Recordable Pictures on an SD
Card
ª Picture quality and number of
Picture quality
recordable pictures
Selecting the picture quality.
Press the MENU button, then select
[PICTURE] # [PICT. QUALITY] #
desired item and press the cursor
button.
2.1Ｍ
(1920t1080)
Picture size
Picture quality
8 MB
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
4
6
10
20
17
32
47
74
94
150
320
640
1290
2630
5160
200
410
820
:
Still pictures with a high picture quality are
recorded.
2 GB
1670
3290
:
Priority is given to the number of still
pictures recorded. Still pictures are
recorded in normal picture quality.
4 GB
≥The number of recordable pictures depends
on whether [ ] and [ ] are used
together and on the subject being recorded.
≥The numbers shown in the table are
approximations.
51
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥If the zoom lever is pushed to the end, you can
zoom from 1k up to 12k in as fast as approx.
1.8 seconds.
Various recording functions
≥When the zoom speed is high, the subject may
not be focused easily.
Zoom in/out function
You can zoom in up to 12k optically.
Digital zoom function
¬ Rotate the mode dial to select
.
Move the zoom lever.
If the zoom magnification exceeds 12k, then the
digital zoom function will be activated. The
maximum magnification provided by the digital
zoom can be switched.
VOL
¬ Rotate the mode dial to select
.
Press the MENU button, then select
[BASIC] # [D.ZOOM] # desired item
and press the cursor button.
W
T
T side: Close-up recording (zoom in)
W side: Wide-angle recording (zoom out)
[OFF]:
Optical zoom only (Up to 12k)
[30k]:
Up to 30k
[700k]: Up to 700k
≥If [30k] or [700k] is selected, the digital zoom
range is displayed in blue while zooming.
≥The larger the digital zoom magnification, the
more the image quality is degraded.
≥If you take your finger off the zoom lever during
zoom operation, the operation sound may be
recorded. When returning the zoom lever to the
original position, move it quietly.
≥When zooming in while holding this unit by
hand, we recommend using the image
stabilizer function. (l 59)
≥When distant subjects are brought closer, they
are focused at about 1.2 m (3.9 feet) or more.
≥When the zoom magnification is 1k, this unit
can focus on a subject approx. 4 cm (1.6q)
away from the lens. (Macro function)
≥The zoom speed varies depending on the
range over which the zoom lever is moved.
(The zoom speed does not vary when
operating with the remote control.)
52
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
About using the zoom
microphone function
Recording yourself
You can record yourself while viewing the LCD
monitor.
The zoom microphone is linked to the zooming
operation and the sound sensitivity direction
(directivity) of the microphone changes as you
zoom. Far away sounds are recorded more
clearly if you zoom in (close-up) and the
surrounding sound is recorded with presence if
you zoom out (wide angle).
¬ Rotate the mode dial to select
.
Rotate the LCD monitor towards the
lens side.
¬ Rotate the mode dial to select
.
Press the MENU button, then select
[VIDEO] # [ZOOM MIC] # [ON] and
press the cursor button.
The image is horizontally flipped as if you see a
mirror image. (However the image recorded is
the same as a normal recording.)
lens side, the icon will not be displayed even if
you press the cursor button.
≥Only some indications will appear on the
screen. When [°] appears, return the
direction of the LCD monitor to normal position
and check the warning/alarm indication.
(l 110)
≥The zoom microphone function does not work
with an external microphone.
≥When zooming in, surrounding sounds are
suppressed and the sound near the front of the
unit is recorded. When recording music recitals
or other events where you wish to record
quality sound and keep a realistic sensation
even when zooming in, we recommend that
you turn the zoom microphone function off.
53
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Backlight compensation
function
This is for preventing a backlit subject
from being darkened.
Fade in/fade out function
Fade in:
The image and audio gradually
appear.
Fade out: The image and audio gradually
disappear.
Use this function when the light is emanating
from behind the subject and the subject appears
dark.
¬ Rotate the mode dial to select
.
1 Press the cursor button. Then
¬ Rotate the mode dial to select
.
move the cursor button down to
display the icon shown in the
illustration.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
2 Move the cursor button left to
select [
].
2 Move the cursor button up to
select [ ].
3 Press the recording start/stop
button.
The image on the screen will become
brighter.
Start recording. (Fade in)
To return to normal recording
Select [
] again.
≥If you turn off the power or operate the mode
dial, the backlight compensation function is
canceled.
When you start recording, the image/audio
gradually appears.
54
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
4 Press the recording start/stop
button.
MagicPix function
This allows recording in dark
locations.
Pause recording. (Fade out)
This function allows you to record color subjects
in dark locations (Minimum required illumination:
approx. 2 lx) to stand out against the background.
Attach this unit to a tripod, and you can record
images free from vibration.
Recorded scene is seen as if frames were
missed.
¬ Rotate the mode dial to select
.
The image/audio gradually disappears. After the
image/audio completely disappears, recording
stops.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
≥After recording, the fade setting is canceled.
To cancel fading
Select [
] again.
To select the color for fade in/out
2 Move the cursor button up to
The color which appears in fading pictures can
be selected.
select [
].
Press the MENU button, then select
[VIDEO] # [FADE COLOR] #
[WHITE] or [BLACK] and press the
cursor button.
To cancel the MagicPix function
≥If you turn off the power, the fade function is
canceled.
Select [
] again.
≥While the fade in/fade out function is selected,
it takes several seconds to display the image
when you start recording. It also takes several
seconds to pause recording.
≥The thumbnails of scenes recorded using fade
in become black (or white).
≥The focus indication does not appear even if
the PHOTO SHOT button is pressed halfway.
≥When using auto focus, it will take some time to
focus in dark areas. If there is difficulty focusing
with auto focus, manually adjust the focus.
≥The flash cannot be used.
≥The MagicPix function makes the signal
charging time of CCD up to approximately 8k
longer than usual, so that dark scenes can be
recorded brightly. For this reason, bright dots
that are usually invisible may be seen, but
this is not a malfunction.
≥If you turn off the power or operate the mode
dial, the MagicPix function is canceled.
≥If set in a bright place, the screen may become
whitish for a while.
55
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Soft skin mode
This makes skin colors appear softer
for a more attractive appearance.
Tele macro function
This is for close-ups bringing only
what you want to record into focus.
This is more effective if you record a subject
more closely from the torso up.
By focusing only on the subject and blurring the
background, the image can be impressive.
The unit can focus on the subject at a distance of
approx. 60 cm (24q).
¬ Rotate the mode dial to select
.
1 Press the cursor button. Then
¬ Rotate the mode dial to select
.
move the cursor button down to
display the icon shown in the
illustration.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
2 Move the cursor button left to
select [
].
2 Move the cursor button right to
select [
].
To cancel the soft skin mode
Select [
] again.
automatically set to 12k.
≥If the background or anything else in the scene
has colors similar to the skin color, they will
also be smoothed.
≥If the brightness is insufficient, the effect may
not be clear.
≥If you record a person in the distance, the face
may not be recorded clearly. In this case,
cancel soft skin mode or zoom in on the face
(close-up) to record.
To cancel the tele macro function
Select [
] again.
≥If a sharper focus cannot be achieved, adjust
the focus manually. (l 64)
≥In the following cases, the tele macro function
is canceled.
– The zoom magnification becomes lower than
12k.
– The power is turned off or the mode dial is
operated.
56
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥The self-timer is canceled if the power is turned
off or the mode dial is operated.
Self-timer recording
≥The self-timer standby mode is canceled when
you press the recording start/stop button to
start motion picture recording.
You can record still pictures on an SD card using
the timer.
¬ Rotate the mode dial to select
.
Even if you press the recording start/stop
button while the self-timer is counting down,
motion picture recording is not possible.
≥Depending on the time taken to bring the
subject into focus, the recording may take
longer than set to start.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
≥Setting the self-timer to [Ø ] is a good way to
2
prevent image shake when the PHOTO SHOT
button is pressed while using a tripod etc.
Built-in flash
Use the built-in flash in order to record still
pictures in dark places.
2 Move the cursor button up to
select [Ø].
¬ Rotate the mode dial to select
.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
Each time the cursor button is pressed up,
the indication changes by one setting in the
following order:
[Ø ] # [Ø ] # setting canceled
10
2
Ø
: Records after 10 seconds
10
Ø : Records after 2 seconds
2
2 Move the cursor button left to
3 Press the PHOTO SHOT button.
select [ß].
A still picture is recorded after the [Ø ] or
10
[Ø ] display and the recording lamp flashes
2
for the time which has been set.
≥After recording, the self-timer is canceled.
≥If you press the PHOTO SHOT button
halfway and then fully in auto focus mode,
the subject is focused when the button is
pressed halfway.
≥When you press the PHOTO SHOT button
fully in auto focus mode, the subject is
focused just before recording.
≥Each time the cursor button is pressed left,
the indication changes by one setting in the
following order: [FLASH ON] >
[FLASH AUTO] > [FLASH OFF]
≥When the PHOTO SHOT button is pressed
halfway, the flash indicator will appear in
the bottom left corner of the screen.
To stop the timer midway through
Press the MENU button. (The self-timer setting is
canceled.)
[FLASH ON]:
ß
[FLASH AUTO]: ßA
[FLASH OFF]:
57
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥When [FLASH AUTO] is set, the ambient
Red eye reduction function
brightness is automatically detected, and
the flash will activate only when necessary.
(If the flash is not necessary, the [ßA]
indicator will not appear when the
PHOTO SHOT button is pressed halfway.)
≥This function’s default setting is
[FLASH AUTO].
Reduces the phenomena where human eyes
become red from flashes.
1 Press the cursor button. Then
move the cursor button down to
display the icon shown in the
illustration.
3 Press the PHOTO SHOT button.
The flash is activated and the picture will be
recorded.
When the flash is not used
Set the flash to [FLASH OFF].
≥Do not block the flash with your hand or by
other means.
2 Move the cursor button right to
select [
].
≥The unit automatically determines if the flash is
necessary even when it has been set to
[FLASH OFF] by detecting the ambient
brightness. (If it determines that the flash is
necessary, the [ ] indication lights up in red
when the PHOTO SHOT button is pressed
halfway.)
≥If the [ß] indication etc. flashes or is not
displayed when the PHOTO SHOT button is
pressed halfway, the flash is not activated.
≥The available range of the flash is approx. 1 m
to 2.5 m (3.3 feet to 8.2 feet) in dark places.
Pictures will appear dark or reddish when they
are recorded by using the flash at distances
greater than 2.5 m (8.2 feet).
≥The flash is activated 2 times. Do not move
until the second flash is finished.
≥Use this when you take pictures of people in
dark places.
≥Red eye phenomenon may appear depending
on the recording conditions.
≥Using the flash fixes the shutter speed of 1/750
or faster to 1/500.
≥The picture may become out of focus in dark
places. If so, adjust the focus manually.
≥The picture may appear dark if the flash is lit in
front of a white background.
To adjust the brightness of the
flash
Press the MENU button, then select
[PICTURE] > [FLASH LEVEL] #
desired item and press the cursor
button.
≥Set the flash to [FLASH OFF] where using a
flash is prohibited.
≥If the flash will be activated a large number of
times, it may take longer to charge it.
[ßj]: If the brightness is too high.
[ßd0]: In normal recording
[ßi]: If the brightness is insufficient.
58
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Image stabilizer function
This is for reducing image shakes
(jitter) during recording.
Guide line function
This is for viewing the slope and the
balance of the image while recording
or playing back.
Reduces the image shaking (jitter) due to hand
movement when recording.
You can check if the image is level while
recording or playing back motion pictures and
still pictures. The function can also be used to
estimate the balance of the composition.
¬ Rotate the mode dial to select
.
Press the MENU button, then select
[BASIC] # [O.I.S.] # [ON] and press
the cursor button.
¬ Rotate the mode dial to select
rotate the mode dial to and then
(motion picture
or
select the
playback) tab. (l 68)
Press the MENU button, then select
[BASIC] or [PLAY SETUP] #
[GUIDE LINES] # desired item and
press the cursor button.
To cancel the image stabilizer function
Press the MENU button, then select [BASIC] #
[O.I.S.] # [OFF] and press the cursor button.
≥This function’s default setting is [ON].
≥In still picture recording mode, pressing the
PHOTO SHOT button halfway increases the
effect of the image stabilizer function. (MEGA
optical image stabilizer)
≥In the following cases, the image stabilizer
function may not work effectively.
– When the digital zoom is used
– When the unit is shaken greatly
– When you record a moving subject while
tracking it
A [HORIZONTAL]
B [GRID1]
C [GRID2]
59
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
To cancel the guide line function
Press the MENU button, then select [BASIC] or
[PLAY SETUP] # [GUIDE LINES] # [OFF] and
press the cursor button.
Microphone level
This is for adjusting the microphone
input level.
When recording, the input level from the built-in
microphones and the external microphone
terminal can be adjusted.
≥The guide lines do not appear on the images
actually recorded.
¬ Rotate the mode dial to select
.
Wind noise reduction function
This is for reducing the wind noise
coming into the microphone when
recording.
1 Press the MENU button, then
select [VIDEO] # [MIC LEVEL] #
[SETrAGC] or [SET] and press
the cursor button.
¬ Rotate the mode dial to select
.
Press the MENU button, then select
[VIDEO] # [WIND CUT] # [ON] and
press the cursor button.
AGC: Auto Gain Control
[AUTO]:
AGC is activated, and the
recording level is adjusted
automatically.
[SETrAGC]: The desired recording level can be
set. AGC will also be activated to
reduce the amount of sound
distortion.
To cancel the wind noise reduction
function
Press the MENU button, then select [VIDEO] #
[WIND CUT] # [OFF] and press the cursor
button.
[SET]:
AGC is not activated and so natural
recording can be performed.
≥This function’s default setting is [ON].
≥The wind noise reduction depends on the wind
strength. (The surround effect may be reduced
if this function is activated in strong winds.
However, the surround effect is automatically
restored when then the wind weakens.)
≥The wind noise reduction function does not
work with an external microphone.
60
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
To return to automatic setting
2 Move the cursor button left or
right to adjust the microphone
input level.
Press the MENU button, then select [VIDEO] #
[MIC LEVEL] # [AUTO], and press the cursor
button.
A
≥Adjust the gain value so that the last 2 bars of
the microphone input level on the center of the
screen are not red. (Otherwise, the sound is
distorted.) Select a lower setting for gain value
or set [MIC LEVEL] to [AUTO].
B
C
D
E
≥The front left and front right gain values only
work when input is from an external
F
A
microphone.
≥The microphone input level meter shows the
largest volume for the microphones.
≥When [ZOOM MIC] is [ON], the volume will be
different depending on the zoom rate. Set
[ZOOM MIC] to [OFF] or set the microphone
input level after adjusting the zoom rate. (l 53)
B
D
E
E
C
A Center
B Front left
C Back left
D Front right
E Back right
F Microphone input level
≥A gain value for each of the 5 built-in
microphones is displayed. (The input level of
the microphones cannot be set individually.)
3 Press the center of the cursor
button to set and then press the
MENU button to finish the
setting.
G
G Microphone input level meter
≥Microphone input level meter is displayed on
the screen.
61
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Zebra display
This is for displaying the parts that
are too bright.
Color bar
This is for displaying a color bar to
check the color tone.
Parts where white saturation (color saturation) is
likely to occur (extremely brightly lit or shiny
parts) are displayed with diagonal lines (zebra
pattern).
This unit displays a 7 color bar which is useful for
adjusting the picture quality of the TV or the
external monitor.
¬ Rotate the mode dial to select
.
¬ Rotate the mode dial to select
.
Press the MENU button, then select
[ADVANCED] # [COLOR BAR]#
[ON] and press the cursor button.
Press the MENU button, then select
[ADVANCED] # [ZEBRA]# [ON] and
press the cursor button.
To cancel the color bar
Press the MENU button, then select
[ADVANCED] # [COLOR BAR] # [OFF] and
press the cursor button.
A
A Zebra pattern
≥You can record an image with little white
saturation if you manually adjust the shutter
speed or brightness (iris/gain) (l 66).
≥This function is canceled when the power is
turned off.
≥The icon will not be displayed even if you press
the cursor button.
To cancel the zebra display
Press the MENU button, then select
[ADVANCED] # [ZEBRA] # [OFF] and press
the cursor button.
≥The zebra pattern does not appear on the
images actually recorded.
62
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
To cancel the scene mode function
Press the MENU button, then select [BASIC] #
[SCENE MODE] # [OFF].
Manual recording functions
≥You can also cancel the scene mode function
by setting the AUTO/MANUAL/FOCUS switch
to AUTO.
Scene mode
This is for recording in various
situations.
Sports mode
When you record images in different situations,
this mode automatically sets optimum shutter
speeds and apertures.
≥For slow-motion playback or playback pause of
recorded pictures, this mode helps diminish
camera shake.
≥During normal playback, the image movement
may not look smooth.
≥Avoid recording under fluorescent light,
mercury light or sodium light because the color
and brightness of the playback image may
change.
≥If you record a subject illuminated with strong
light or a highly reflective subject, vertical lines
of light may appear.
¬ Rotate the mode dial to select
.
1 Set the AUTO/MANUAL/FOCUS
switch to MANUAL.
AUTO
MANUAL
FOCUS
≥If the brightness is insufficient, the sports mode
does not function. The [5] display flashes.
≥If this mode is used indoors, the screen may
flicker.
2 Press the MENU button, then
select [BASIC] # [SCENE MODE]
# desired item and press the
cursor button.
Portrait mode
≥If this mode is used indoors, the screen may
flicker. If so, change the scene mode setting to
[OFF].
Low light mode
≥Extremely dark scenes may not be able to be
recorded finely.
Spotlight mode
[5] Sports
≥If the recording subject is extremely bright, the
recorded image may become whitish and the
periphery of the recorded image extremely
dark.
Surf & snow mode
≥If the subject is extremely bright, the recorded
image may become whitish.
To record sports scenes or scenes where there
are quick motions
[
] Portrait
To make people stand out against the
background
[
] Low light
To make the scene brighter in dark conditions
] Spotlight
[
To make the subject under a spotlight look more
attractive
[
] Surf & snow
To record images in bright places such as ski
slopes and beaches
63
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
4 Move the cursor button left or
right to bring the subject into
focus.
Manual focus adjustment
If auto focusing is difficult due to the conditions,
then manual focusing is available.
¬ Rotate the mode dial to select
.
1
(When MF assist function is used)
Press the MENU button, then
select [ADVANCED] #
[MF ASSIST] # [ON] and press
the cursor button.
The center of the screen is enlarged. The
normal screen returns approximately
2 seconds after you finish bringing the
subject into focus.
≥The center of the screen is not enlarged
when [MF ASSIST] is [OFF].
To restore to the automatic adjustment
Press the AUTO/MANUAL/FOCUS switch down
again to the FOCUS position.
≥The default setting is [ON].
≥You can also restore the auto focusing by
setting the AUTO/MANUAL/FOCUS switch to
AUTO.
2 Set the AUTO/MANUAL/FOCUS
switch to MANUAL.
AUTO
≥The subject may not be in focus when zoomed
in if focusing with a wide angle. First, zoom in
on the subject, and then focus on it.
MANUAL
FOCUS
3 Move the switch down and set it
to FOCUS position.
AUTO
About the MF assist function
MANUAL
FOCUS
The center of the screen is enlarged during
manual focus adjustment. This allows you to
focus on the subject more easily.
The manual focus indication [MF] and the
icon shown in the illustration appear.
≥MF assist does not work if the zoom
magnification is more than 12k.
≥The part of the screen that is enlarged is not
enlarged on the image actually recorded.
≥The zebra pattern does not appear on the part
of the screen that is enlarged when [ZEBRA] is
[ON].
64
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥Lights used for wedding receptions at
hotels, stage spotlights in theatres
≥Sunrise, sunset etc.
White balance
This is for recording in natural colors.
The automatic white balance function may not
reproduce natural colors depending on the
scenes or lighting conditions. If so, you can
adjust the white balance manually.
To restore to the automatic adjustment
Set the white balance mode to [
].
AWB
≥You can also restore the automatic adjustment
by setting the AUTO/MANUAL/FOCUS switch
to AUTO.
¬ Rotate the mode dial to select
.
1 Set the AUTO/MANUAL/FOCUS
To set the white balance manually
switch to MANUAL.
1 Select [ ], fill the screen with a
white subject.
The icon shown in the illustration is displayed
automatically.
2 Move the cursor button up to
2 Move the cursor button up to
select [
].
select [ ].
3 Move the cursor button left or
right to select the white balance
mode.
≥When the [
flashing to on, setting is complete.
≥When the [
the white balance cannot be set because
the place is dark etc. In this case, use the
automatic white balance.
] display changes from
] display continues flashing,
[
[
]: Auto white balance adjustment
AWB
]:
Indoor mode (for recording under
incandescent lamps)
≥Incandescent lights, halogen lamps
[
[
]:
]:
Outdoor mode
≥Outdoors under a clear sky
Manual adjustment mode
≥Mercury-vapor lamps, sodium lamps,
some fluorescent lights
65
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
ª About the white balance sensor
Manual shutter speed/aperture
adjustment
Shutter Speed:
Adjust it when recording fast-moving subjects.
Aperture:
A
Adjust it when the screen is too bright or too
dark.
The white balance sensor A detects the type of
light source during recording.
Do not cover the white balance sensor during
recording, or it may not function properly.
¬ Rotate the mode dial to select
.
1 Set the AUTO/MANUAL/FOCUS
ª About the black balance
switch to MANUAL.
adjustment
This is one of the 3CCD system functions that
automatically adjusts the black when the white
balance is set in the manual adjustment mode.
When the black balance is adjusted, the screen
will temporarily be black. (The black balance
cannot be adjusted manually.)
The icon shown in the illustration is displayed
automatically.
1
2
3
2 Move the cursor button left or
right to select [ ] (aperture) or
[
] (shutter speed).
1 Black balance adjustment in progress.
(Flashes.)
2 White balance adjustment in progress.
(Flashes.)
3 Adjustment completed. (Lights up.)
≥When the [ ] display flashes, the manual
white balance previously adjusted is stored.
Whenever recording conditions change, re-set
the white balance for correct adjustment.
≥When setting both the white balance and the
iris/gain, set the white balance first.
3 Move the cursor button left or
right to make the adjustment.
A Shutter speed:
1/60 to 1/8000
≥The shutter speed closer to 1/8000 is faster.
B Iris/Gain value:
CLOSE # (F16 to F2.0) # OPEN # (0dB to
18dB)
≥Value closer to [CLOSE] darken the image.
≥Value closer to [18dB] brighten the image.
66
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
≥When the iris value is adjusted to brighter than
[OPEN], it changes to the gain value.
To restore to automatic adjustment
Set the AUTO/MANUAL/FOCUS switch to
AUTO.
≥When setting both the shutter speed and the
iris/gain value, set the shutter speed and then
set the iris/gain value.
Manual shutter speed adjustment
≥Avoid recording under fluorescent light,
mercury light or sodium light because the color
and brightness of the playback image may
change.
≥If you increase the shutter speed manually, the
gain value will increase automatically
depending on how much the sensitivity lowers
and the noise on the screen may increase.
≥When recording still pictures, we recommend
setting the shutter speed to 1/500 or less for
even more beautiful pictures.
≥You may see vertical lines of light in the
playback image of a brightly shining subject or
highly reflective subject, but this is not a
malfunction.
≥During normal playback, image movement may
not look smooth.
≥When recording in an extremely bright place,
the screen may change color or flicker. If so
adjust the shutter speed manually to [1/60] or
[1/100].
Manual iris/gain adjustment
≥If the gain value is increased, the noise on the
screen increases.
≥Depending on the zoom magnification, there
are iris values that are not displayed.
67
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
3 Select the scene to be played
Playback
back.
Motion picture playback
Play back motion pictures.
1 Rotate the mode dial to select
B
C
.
D
B Previous page
C Next page
D Scene number
The selected scene will be encircled by a
yellow frame.
≥If 9 or more scenes have been recorded,
the next (or previous) page can be
displayed by moving the cursor button left
and right or moving the cursor button down,
The lens cover closes.
2 Press the cursor button up and
then left to select the
picture playback) tab.
(motion
selecting
/
by moving the
cursor button left and right and then
pressing the center of the cursor button.
≥The scene number display switches to the
page number when the motion picture
A
playback tab or
selected.
/
is
4 Press the cursor button.
A Motion picture playback tab
The motion pictures are displayed as
thumbnails (reduced-size images).
The selected scene is played back on the full
screen.
≥The operation icon is automatically
displayed on the screen.
5 Move the cursor button to
operate.
1/;:
Playback/Pause
6 (Move and hold): Review playback*
5 (Move and hold): Cue playback*
∫:
Stops the playback
and shows the
thumbnails.
* Press the 6 or 5 button on the remote
control.
68
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
ª About motion picture
Skip playback (to the start of a
scene)
(Operation is possible with the remote
control only.)
compatibility
≥This unit is based on the AVCHD format.
≥The video signal that can be played back on
this unit is 1440k1080/60i.
≥This unit may degrade or not playback motion
pictures recorded or created on other products,
and other products may degrade or not
playback motion pictures recorded on this unit,
even if the products support the AVCHD.
Press the : or 9 button on the
remote control during playback.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
≥No sound will be heard except during normal
playback.
≥If pause play is continued for 5 minutes, the
screen returns to the thumbnails.
≥When the amount of time recorded on the
scene is short, playback may not be possible.
≥Scenes which cannot be displayed as
thumbnails (the thumbnails are displayed as
) cannot be played back. An error
message appears and the screen shows the
thumbnails.
≥The power will not turn off even if the LCD
monitor is closed.
≥The date/time displayed may be different from
the recording date/time and it may take time to
display the thumbnail display when playing
back motion pictures not recorded on this unit.
≥The remaining time for playback indication will
be reset to “0h00m00s” each scene.
Slow-motion playback
1 Move the cursor button up during
playback to pause the playback.
2 Move and hold the cursor button
right. (Slow-motion pictures will
be played back in reverse when
you move and hold the cursor
button left.)
≥Normal playback is restored when you
move the cursor button up.
≥When slow-motion pictures are played
back in reverse, they will be shown
continuously at intervals of 0.5 seconds.
ª Operating with the remote
control
Press the E or D button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
69
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Frame-by-frame playback
To adjust the volume
The motion picture is advanced one frame at a
time.
Adjust the speaker volume during playback.
Move the volume lever to change
the volume level.
1 Move the cursor button up during
playback to pause the playback.
2 Move the cursor button right.
(The frames will be advanced one
at a time in the reverse direction
when you move the cursor
button left.)
VOL
15
W
T
Towards “r”: increases the volume
Towards “s”: decreases the volume
≥The further the [ ] indicator moves to the right,
the higher the volume level becomes.
≥When the adjustment is completed, the volume
setting display will disappear.
≥Normal playback is restored when you
move the cursor button up.
≥When the frames are advanced one at a
time in the reverse direction, they will be
shown in intervals of 0.5 seconds.
ª Operating with the remote
control
1) Press the ; button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
2) Press the E or D button.
SEARCH
STILL ADV
SKIP
PLAY
PAUSE
STOP
SEARCH
STILL ADV
SKIP
70
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Playing back motion pictures
by date
Repeat playback
Playback of the first scene starts after playback
of the last scene finishes.
Recorded scenes are grouped by date on this
unit.
Press the MENU button, then select
[PLAY SETUP] # [REPEAT PLAY] #
[ON] and press the cursor button.
Scenes recorded on the same day can be played
back in succession.
1 Press the MENU button, then
select [PLAY SETUP] #
[PLAY MODE] # [BY DATE] and
press the cursor button.
The [
] indication appears on the thumbnail
and full screen views.
≥The following scenes can be played back
repeatedly.
– When [PLAY MODE] is set to [VIEW ALL]:
All the scenes on the SD card
– When [PLAY MODE] is set to [BY DATE]:
All the scenes on the selected date
2 Select the date for playback, then
press the cursor button.
To cancel the repeat playback function
Press the MENU button, then select
[PLAY SETUP] # [REPEAT PLAY] # [OFF] and
press the cursor button.
The scenes recorded on the same day are
displayed as thumbnails.
3 Select the scene to be played
back.
To return to playing back all the scenes
Press the MENU button, then select
[PLAY SETUP] # [PLAY MODE] # [VIEW ALL]
and press the cursor button.
≥When [PLAY MODE] is set to [VIEW ALL], all
recorded motion pictures will be played back in
succession. ([
] is displayed.)
≥Playing back all the scenes returns if the power
is turned off or the mode dial is operated.
≥Even if scenes are recorded on the same day,
they are grouped separately in the following
cases.
– When the number of scenes exceeds 99
– When the card is repaired
71
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Still picture (JPEG) playback
Play back the still pictures recorded on the card.
Resuming the previous
playback
1 Rotate the mode dial to select
If playback of a scene was stopped halfway, the
playback can be resumed from where it was
stopped.
.
Press the MENU button, then select
[PLAY SETUP] # [RESUME PLAY] #
[ON] and press the cursor button.
The lens cover closes.
2 Press the cursor button up and
then right to select the
picture playback) tab.
(still
If playback of a motion picture is stopped, [
appears on the thumbnail view of the stopped
scene.
]
A
To cancel the resume playback function
Press the MENU button, then select
[PLAY SETUP] # [RESUME PLAY] # [OFF]
and press the cursor button.
≥The memorized resume position is cleared if
you turn off the power or operate the mode dial.
(The [RESUME PLAY] setting is kept.)
A Still picture playback tab
The still pictures recorded on the SD card
are displayed as thumbnails (reduced-size
images).
3 Select the file to be played back.
B
C
D
E
B Previous page
C Next page
D File number display
E Folder/file name
The selected file will be encircled by a yellow
frame.
72
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
≥If 9 or more files have been recorded, the
next (or previous) page can be displayed
by moving the cursor button left and right or
moving the cursor button down, selecting
ª About still picture compatibility
≥This unit is compliant with the unified standard
DCF (Design rule for Camera File system)
established by JEITA (Japan Electronics and
Information Technology Industries
Association).
≥The file format supported by this unit is JPEG.
(Not all JPEG formatted files will be played
back.)
/
by moving the cursor
button left and right and then pressing the
center of the cursor button.
≥The file number display switches to the
page number when the still picture
playback tab or
selected.
/
is
≥If a non-standard file is played back, the folder/
file name may not be displayed.
≥This unit may degrade or not play back data
recorded or created on other products and
other products may degrade or not play back
data recorded on this unit.
4 Press the cursor button.
≥While this unit accesses the SD card (the
access lamp is lit), do not remove the SD card.
≥Do not operate the mode dial during the slide
show.
≥It takes time to display the file depending on the
number of pixels of the file.
The selected file is played back on the full
screen.
≥The operation icon is automatically
displayed on the screen.
≥Files which cannot be displayed as thumbnails
(the thumbnails are displayed as
be played back.
) cannot
5 Move the cursor button to
≥If you attempt to play back a file which is a
different format or a damaged file, an error
message appears and the screen shows the
thumbnails.
≥The date/time displayed may be different from
the recording date/time and it may take time to
display the thumbnail display when playing
back still pictures not recorded on this unit.
≥The power will not turn off even if the LCD
monitor is closed.
operate.
1/;: Slide show (playback of the still
pictures on the SD card in numerical
order) start/pause.
E:
D:
∫:
Plays back the previous picture.
Plays back the next picture.
Stops the playback and shows the
thumbnails.
73
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
Editing
Deleting multiple scenes from the
thumbnail display
Editing scenes
¬ Rotate the mode dial to select
and then select the
picture playback) tab.
(motion
Deleting scenes
This is for deleting scenes recorded
on SD cards.
1 Press the
button while the
thumbnail view screen is
displayed.
The deleted scenes cannot be restored.
Deleting scenes one at a time
¬ Rotate the mode dial to select
and then select the
(motion
picture playback) tab.
2 Move the cursor button up or
down to select [ALL SCENES] or
[SELECT] and press the cursor
button.
1 Press the
button during
playback.
2 When the confirmation message
appears, select [YES], then press
the cursor button.
≥When [ALL SCENES] is selected, the
following scenes except the protected
scenes will be deleted. Proceed to step 5.
–When [PLAY MODE] is set to [VIEW ALL]:
All the scenes on the SD card
–When [PLAY MODE] is set to [BY DATE]:
All the scenes selected by date
3
(Only when [SELECT] is selected in step 2)
Select the scene to be deleted,
then press the cursor button.
The selected scene is encircled by a red
frame.
≥When the cursor button is pressed again,
the selected scene will be canceled.
≥Up to 50 scenes can be set in succession.
74
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
4
(Only when [SELECT] is selected in step 2)
Protecting scenes
Press the
button.
This is for preventing scenes from
being deleted by mistake.
5 When the confirmation message
appears, select [YES], then press
the cursor button.
Scenes can be protected so that they are not
deleted by mistake. (Even if you protect some
scenes on an SD card, formatting the SD card
will delete them.)
(Only when [SELECT] is selected in step 2)
To continue deleting other scenes
Repeat steps 3-5.
¬ Rotate the mode dial to select
and then select the
(motion
To complete editing
Press the MENU button.
picture playback) tab.
1 Press the MENU button, then
select [PLAY SETUP] #
≥Scenes which cannot be played back (the
thumbnails are displayed as
deleted.
) cannot be
[SCENE PROTECT] # [YES] and
press the cursor button.
≥Protected scenes cannot be deleted.
≥Do not open the card slot cover while deleting.
The deletion will stop.
≥In case of [ALL SCENES], the deletion may
take time if there are many scenes on the SD
card.
≥Do not turn off this unit while deleting.
≥When you delete scenes, use a battery with
sufficient battery power or use the AC adaptor.
≥If you delete scenes recorded on other
products with this unit, all the data related to
the scenes may be deleted.
2 Select the scene to be protected
and then press the center of the
cursor button.
The [
] indication appears and the scene
is protected.
≥Press the cursor button again to cancel the
setting.
≥2 or more scenes can be set in succession.
To complete the settings
Press the MENU button.
75
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
Editing still pictures
Deleting multiple files from the
thumbnail display
Deleting still pictures
This is for deleting still picture files
recorded on SD cards.
¬ Rotate the mode dial to select
and then select the
playback) tab.
(still picture
The deleted files cannot be restored.
1 Press the
button while the
thumbnail view screen is
displayed.
Deleting files one at a time
¬ Rotate the mode dial to select
and then select the
playback) tab.
(still picture
1 Press the
button during
playback.
2 Move the cursor button up or
down to select [ALL SCENES] or
[SELECT] and press the cursor
button.
2 When the confirmation message
appears, select [YES], then press
the cursor button.
≥When [ALL SCENES] is selected, all files
on the SD card except the protected files
will be erased. Proceed to step 5.
3
(Only when [SELECT] is selected in step 2)
Select the file to be deleted, then
press the cursor button.
The selected file is encircled by a red frame.
≥When the cursor button is pressed again,
the selected file will be canceled.
≥Up to 50 files can be set in succession.
4
(Only when [SELECT] is selected in step 2)
Press the
button.
76
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
5 When the confirmation message
appears, select [YES], then press
the cursor button.
Protecting still pictures
This is for preventing still picture files
from being deleted by mistake.
(Only when [SELECT] is selected in step 2)
To continue deleting other files
Repeat steps 3-5.
Files recorded on an SD card can be protected
so that they are not deleted by mistake. (Even if
you protect some files on an SD card, formatting
the SD card will delete them.)
To complete editing
¬ Rotate the mode dial to select
Press the MENU button.
and then select the
playback) tab.
(still picture
ª Deleting still picture files
recorded on an SD card by other
products
A still picture file (other than JPEG) that cannot
be played back on this unit may be erased.
1 Press the MENU button, then
select [PLAY SETUP] #
[SCENE PROTECT] # [YES] and
press the cursor button.
≥Protected files cannot be deleted.
≥Do not open the card slot cover while deleting.
The deletion will stop.
≥In case of [ALL SCENES], the deletion may
take time if there are many files on the SD card.
≥Do not turn off this unit while deleting.
≥When you delete files, use a battery with
sufficient battery power or use the AC adaptor.
≥If files conforming to DCF standard are deleted,
all the data related to the files will be deleted.
2 Select the file to be protected and
then press the center of the
cursor button.
The [
] indication appears and the file is
protected.
≥Press the cursor button again to cancel the
setting.
≥You can also select multiple files in
succession.
To complete the settings
Press the MENU button.
77
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
To cancel all DPOF settings
Press the MENU button, then select
[PLAY SETUP] # [DPOF SET] #
[CANCEL ALL] and press the cursor button.
≥When the confirmation message appears,
select [YES], then press the cursor button.
DPOF setting
This is for writing the printing data on
an SD card.
You can write the data of the still pictures to be
printed and the number of prints (DPOF data)
onto the SD card.
ª What is DPOF?
¬ Rotate the mode dial to select
and then select the
playback) tab.
DPOF stands for Digital Print Order Format. This
enables picture printing information to be written
onto an SD card so that it can be used on a
system supporting DPOF.
(still picture
1 Press the MENU button, then
select [PLAY SETUP] #
≥The DPOF setting can be established for up to
999 prints.
≥DPOF setting made on other devices may not
be recognized by this unit. Please perform the
DPOF settings on this unit.
[DPOF SET] # [SET] and press
the cursor button.
≥You cannot add the recording date to pictures
to be printed with the DPOF settings.
2 Select the file to be set and then
press the center of the cursor
button.
The number of prints set to be in DPOF is
displayed.
3 Move the cursor button up or
down to select the number of
prints, then press the cursor
button.
≥You can select from 0 to 999. (The selected
number of pictures can be printed with the
printer supporting DPOF.)
≥To cancel the setting, set the number of
prints to [0].
≥You can also select multiple files in
succession.
To complete the settings
Press the MENU button.
78
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Card management
Card management
Formatting
Formatting an SD card
This is for initializing cards.
Please be aware that if an SD card is
formatted, then all the data recorded on the
card will be erased. Store important data on a
computer etc.
¬ Rotate the mode dial to select
or
.
1 Press the MENU button, then
select [SETUP] #
[FORMAT CARD] # [YES] and
press the cursor button.
2 When the confirmation message
appears, select [YES], then press
the cursor button.
≥When formatting is complete, press the
MENU button to exit the message screen.
≥Use this unit to format SD cards. If an SD card
is formatted on other products (such as a
computer), the time spent for recording may
become longer and you may not be able to use
the SD card.
≥Depending on the type of SD card being used,
it may take time to format.
≥During formatting, do not turn this unit off.
≥When you format the SD card, use a battery
with sufficient battery power or the AC adaptor.
≥Do not remove the SD card while formatting.
79
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
≥Use the AC adaptor to free you from worrying
about the battery running down.
With other products
With a TV
ª To display the on-screen
information on the TV
Playback on TV
The information displayed on the screen
(operation icon and time code etc.) can be
displayed on the TV.
The motion pictures and still pictures recorded
on this unit can be played back on a TV screen.
Connect this unit to a TV with one of the
following terminals. When connecting to a
HDMI terminal, a connection cable (optional)
is necessary.
Press the EXT DISPLAY button on the remote
control.
START/
PHOTO
SHOT
EXT
¬ Difference in picture quality
depending on the terminal used for
connection
STOP
DISPLAY
DATE/
TIME
ZOOM
VOL
≥Press the button again to erase the information.
≥The screen on this unit will not change.
A
B
C
D
E
ª To watch images with a 16:9
aspect ratio on a regular TV (4:3)
When playing back motion pictures or still
pictures recorded on this unit with a 16:9 aspect
ratio on a TV with a 4:3 aspect ratio, the images
on the screen may be squeezed horizontally.
In this case, change the menu setting to play
back the pictures in the original aspect ratio.
(Depending on the TV setting, the pictures may
not be displayed correctly. For more information,
please read the operating instructions of your
TV.)
A High quality
B Standard quality
C HDMI terminal
D Component terminal
E Video terminal
TV/Devices you use
Reference items
TV with a HDMI
terminal
1 Connecting with
a HDMI cable
(optional) (l 81)
Press the MENU button, then select
[SETUP] # [TV ASPECT] # [4:3] and
press the cursor button.
Example of images with a 16:9 aspect ratio on a
regular TV (4:3)
TV with a HDMI
terminal and AV
amplifier with a
HDMI terminal
2 Listening in 5.1
channel sound
(l 83)
TV with a
component
terminal
3 Connecting with
the component
cable (supplied)
and the AV cable
(supplied) (l 84)
[TV ASPECT] setting
[16:9]
[4:3]
Other TVs
4 Connecting with
the AV cable
(supplied) (l 86)
≥Do not use any other AV cables except the
supplied one.
≥Do not use any other component cables except
the supplied one.
80
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
What is HDMI?
HDMI is the next-generation interface for digital devices. When this unit is connected to a HDMI
compatible device, the image and audio can be output with a digital signal. If you connect this unit
and a HDMI compatible high definition TV and then play back the recorded high definition images
(l 13), you can enjoy them in high resolution with high quality sound.
TM
TM
If you connect this unit to a Panasonic TV compatible with EZ Sync (HDAVI Control ),
linked operations are possible. (l 87)
1 Connect this unit and a TV with the HDMI cable (optional).
HDMI IN
A
Use a HDMI cable (optional) A with the logo shown above.
2 Set the mode dial to
to turn on the power.
3 Select the input channel on the TV.
Example: Select the [HDMI] channel etc.
(The name of the channel may differ depending on the connected TV.)
4 Start playback on this unit.
The image and audio are output on the TV.
ª If the image or audio from this unit is not output on the TV
≥Check that the plugs are inserted as far as they go.
≥Check the connected terminal.
≥Check the input setting (input switch) and the audio input setting on the TV. (For more
information, please read the operating instructions for the TV.)
≥Check [HDMI RESOLUTION]. (l 82)
81
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
ª About the settings when
1080i
connecting with HDMI
When this unit is connected to another device
with a HDMI cable, the output setting on this unit
can be changed.
This is an interlace scan method which scans
1080 scan lines to display a high definition
image. The 1080 available scan lines are
divided in half and scanned on the screen
th
alternatively every 1/60 of a second. The
HDMI output resolution
You can switch the method to output the images.
number of available scan lines is more than
double the 480 scan lines used to display
standard images until now so the images have
clearer detail and a lot of presence.
480p
This is a progressive scan method which
scans all 480 available scan lines on the
screen at the same time every 1/60 of a
second. This method reduces the flickering as
the scan lines are not scanned on the screen
alternatively like in the interlace method.
480i
Press the MENU button, then select
[SETUP] # [HDMI RESOLUTION] #
desired item and press the cursor
button.
[AUTO]:The output resolution is automatically set
based on the information from the
connected TV.
th
Information from the
Output resolution
connected TV
This is an interlace scan method in which the
480 available scan lines are divided in half
and scanned on the screen alternatively every
720p, 1080i
Others
1080i
480p
th
1/60 of a second.
[1080i]: The interlace method with 1080 available
scan lines is used for output.
[480p]: The progressive method with 480
available scan lines is used for output.
Interlace method/progressive method
Video signals until now (NTSC) are referred to
as 480i (i is short for interlace) whereas a
high-density video signal that doubles the
number of scan lines is called 480p (p is short
for progressive).
The component terminal and the HDMI
terminal on this unit are also compatible with
high definition image output 1080i. It is
necessary to have a compatible TV to enjoy
progressive and high definition images.
≥If the images are not output on the TV when the
setting is [AUTO], switch to the method [1080i]
or [480p] which enables the images to be
displayed on your TV. (Please read the
operating instructions for the TV.)
≥Be sure to connect to an HDMI input terminal.
Do not connect to an HDMI output terminal on
other products.
82
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
2 Listening in 5.1 channel sound
If you connect this unit and an AV amplifier with a HDMI terminal with a HDMI cable and then playback,
you can listen to 5.1 channel sound recorded from the internal microphones.
≥Please read the operating instructions for the AV amplifier, speakers and TV for more information
about how to connect them etc.
C
C
E
B
A
F
HDMI IN
D
D
A
A HDMI cable (optional)
≥Use a HDMI cable (optional) with the logo shown above.
B Center speaker
C Front speaker
D Surround speaker
E Subwoofer
F AV amplifier (optional)
≥If you connect this unit to a Panasonic AV amplifier and Panasonic TV that are compatible with
TM
TM
EZ Sync (HDAVI Control ), linked operations become possible. (l 87)
≥Audio recorded from an external microphone is in stereo (2ch).
83
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
3 Connecting with the component cable (supplied) and the AV cable
(supplied)
1 Connect this unit and a TV with the component cable (supplied) and the
AV cable (supplied).
A
C
A/V
COMPONENT
COMPONENT
VIDEO IN
AUDIO IN
B
A Component cable (supplied)
B AV cable (supplied)
≥Connect to terminals of the same color.
≥The component terminal C is for outputting images only so be sure to also connect the AV cable.
(Insert it in the audio input terminal for the component terminal input. Refer to the operating
instructions of the TV for details.)
2 Set the mode dial to
to turn on the power.
3 Select the input channel on the TV.
Example: Select the [Component] channel etc.
(The name of the channel may differ depending on the connected TV.)
4 Start playback on this unit.
The image and audio are output on the TV.
ª About the setting when connecting the component terminals
When this unit is connected to a TV with the component cable, the output setting on this unit can be
changed. Set it to match the terminal on the TV that you connect to.
Press the MENU button, then select [SETUP] # [COMPONENT OUT] #
desired item and press the cursor button.
[480i]: When connecting to the component terminal on the TV compatible with 480i.
(Playback is in standard quality.)
[1080i]: When connecting to the component terminal on the TV compatible with 1080i.
(Playback is in high definition quality.)
84
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
ª If the image or audio from this
unit is not output on the TV
≥Check that the plugs are inserted as far as they
go.
≥Check the connected terminal.
≥Check the TV’s input setting (input switch).
(For more information, please read the
operating instructions for the TV.)
≥If the images are not displayed correctly on a
wide-screen TV, adjust the aspect setting on
the TV. (Refer to the operating instructions of
the TV for details.) If the pictures are displayed
squeezed horizontally on a regular TV (4:3),
change the setting on this unit. (l 80)
85
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
4 Connecting with the AV cable (supplied)
1 Connect this unit and a TV with the AV cable (supplied).
VIDEO IN
AUDIO IN
A
A AV cable (supplied)
2 Set the mode dial to
to turn on the power.
3 Change the input channel on the TV.
Example: Select the [Video 2] channel etc.
(The name of the channel may differ depending on the connected terminal.)
4 Start playback on this unit.
The image and audio are output on the TV.
ª If the image or audio from this unit is not output on the TV
≥Check that the plugs are inserted as far as they go.
≥Check the connected terminal.
≥Check the TV’s input setting (input switch). (For more information, please read the operating
instructions for the TV.)
≥When a HDMI cable is connected at the same time, priority is given to the output from the HDMI
cable.
≥When the component cable is connected at the same time, priority is given to the component cable for
image output.
≥If the images are not displayed correctly on a wide-screen TV, adjust the aspect setting on the TV.
(Refer to the operating instructions of the TV for details.) If the pictures are displayed squeezed
horizontally on a regular TV (4:3), change the setting on this unit. (l 80)
86
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
Playback using EZ Sync™ (HDAVI Control™)
TM
TM
If you connect this unit to a Panasonic TV compatible with EZ Sync (HDAVI Control ) with a HDMI
cable, the following linked operations become possible.
≥You can use the remote control for the TV to control playback on this unit.
≥If you use the remote control for the TV to turn off the power, the power on this unit also turns off.
(When recording motion pictures, formatting, deleting, recovering or connecting the unit to a
computer with a USB cable, the power will not turn off.)
≥If you connect with a HDMI cable and then turn on the power on this unit, the input channel on the
TV automatically switches to this unit’s screen. If the TV’s power is in standby status, it will turn on
automatically (if [Set] has been selected for the TV’s [Power on link] setting).
– Depending on the HDMI terminal on the TV, the input channel may not switch automatically. In
this case, use the remote control for the TV to switch the input channel. (For details on how to
switch input, please read the operating instructions for the TV.)
≥If EZ Sync does not work properly, refer to page 119.
1 Connect this unit and a Panasonic TV compatible with EZ Sync with a
HDMI cable (optional).
HDMI IN
A
≥Use a HDMI cable (optional) A with the logo shown above.
≥If the TV has two or more HDMI input terminals, it is recommended to connect this unit to HDMI2
or HDMI3.
2 Set so that EZ Sync is activated on the connected TV.
≥Read the operating instructions of the TV for how to set etc.
3 Set the mode dial to
to turn on the power.
4 Press the MENU button, then select [SETUP] # [EZ Sync] # [ON] and
press the cursor button.
≥The default setting is [ON].
87
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
5 Operate with the remote control for the TV.
1)
2)
A
DISPLAY ON/OFF
B
C
D
1) Press the button up, down, left or right to select a scene or file to be played back, and then press
the button in the center to set it.
A
B
C
D
Operation icons
Display operation icons
Cancel operation icons
Display/Cancel operation icons
≥The playback operation is performed the same as on this unit.
– Playing back motion pictures (l 68)
– Playing back still pictures (l 72)
To cancel EZ SyncTM (HDAVI ControlTM
)
Press the MENU button, then select [SETUP] # [EZ Sync] # [OFF] and press the cursor button.
≥If you are unsure whether or not the TV and AV amplifier you are using are compatible with EZ Sync,
read the operating instructions for the devices.
≥Available linked operations between this unit and a Panasonic TV is different depending on the types
of Panasonic TVs even if they are compatible with EZ Sync. Refer to the operating instructions of the
TV for the operations that support on the TV.
≥Operation is not possible with a cable that is not based on the HDMI standard. We recommend
Panasonic cables.
Part numbers: RP-CDHG15 (1.5 m/4.9 feet), RP-CDHG30 (3.0 m/9.8 feet), RP-CDHG50 (5.0 m/
16.4 feet), etc.
88
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
≥If the date and time display and function
indication are unnecessary, cancel them before
dubbing. (l 41, 80)
Dubbing images onto a
connected DVD recorder or
video device
If the dubbed images are played back on a
wide-screen TV, the images may be stretched
vertically.
In this case, refer to the operating instruction
of the device you are connecting to or read the
operating instructions of the wide-screen TV
and set the aspect ratio to 16:9.
This is for dubbing images recorded on this unit
onto a DVD recorder, video device etc.
≥Images are dubbed in standard quality.
≥Use the AC adaptor to free you from worrying
about the battery running down.
1 Connect this unit and a video
device.
A
VIDEO IN
AUDIO IN
A AV cable (supplied)
≥Insert the plugs as far as they will go.
2 Set the mode dial to
to turn
on the power.
3 Change the input channel on the
video device and TV.
≥The channel set will differ depending on the
terminal to which the unit is connected.
4 Start playback on this unit. Then
start recording on the connected
device.
≥See the operating instructions of the video
device for details.
To stop dubbing
1) Stop recording on the connected device.
2) Then stop playback on this unit.
89
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
3 Move the cursor button up or
down to select the desired
With a printer (PictBridge)
To print pictures by directly connecting this unit
to the printer, use a printer compatible with
PictBridge. (Read the operating instructions for
the printer.)
≥Use the AC adaptor to free you from worrying
about the battery running down.
number of prints, then press the
cursor button.
≥You can set up to 9 prints.
≥To cancel the setting, set the number of
prints to [0].
≥Up to 8 files displayed can be set in
succession by repeating steps 2 and 3.
¬ Insert an SD card with recorded
images in this unit and then set the
4 Press the MENU button to
mode dial to
to turn on the power.
display the PictBridge menus.
1 Connect this unit and a printer.
5 Select the date print setting on
[DATE PRINT].
A
A USB cable (supplied)
≥Insert the plugs as far as they will go.
The [PictBridge] indication appears on this unit’s
screen.
≥If the printer is not capable of date printing,
this setting is unavailable.
≥If the [PictBridge] indication does not appear or
continues to flash, disconnect and then
reconnect the USB cable or check the printer,
SD card and settings on this unit.
6 Select the paper size setting on
[PAPER SIZE].
≥Do not use any other USB connection cables
except the supplied one. (Operation is not
guaranteed with any other USB cables.)
2 Select a file to be printed, then
press the cursor button.
[STANDARD]: Size specific to the printer
[4k5 INCH]:
[5k7 INCH]:
[4k6 INCH]:
[A4]:
L size
2L size
Postcard size
A4 size
≥You cannot set paper sizes not supported on
the printer.
The number of pictures set is displayed.
90
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With other products
When you stop printing halfway
Move the cursor button down.
7 Select the layout setting on
[PAGE LAYOUT].
A confirmation message appears. If [YES] is
selected, the number of prints set is canceled
and the screen returns to step 2. If [NO] is
selected, all the settings are kept and the screen
returns to step 3.
≥Avoid the following operations during printing.
These operations disable proper printing.
– Disconnecting the USB cable
– Removing the SD card
– Switching the mode dial
– Turning off the power
≥Check the settings for the paper size, print
quality etc. on the printer.
≥The edges of still pictures recorded on this unit
with a 16:9 aspect ratio may be cut at printing.
When using a printer with a trimming or
borderless printing function, cancel this
function before printing. (Refer to the operating
instructions of the printer for details.)
≥You may not be able to print still pictures
recorded with other products.
[STANDARD]: Layout specific to the printer
[
[
]:
No frame print
Frame print
]:
≥You cannot set page layouts not supported on
the printer.
8 Select [PRINT] # [YES] and press
the cursor button to print the
pictures.
≥When the unit is connected directly to the
printer, the DPOF settings cannot be used.
≥Connect the printer directly to this unit. Do not
use a USB hub.
≥Exit PictBridge by disconnecting the USB cable
(supplied) after the pictures have been printed.
91
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
With a computer
Before using with a computer
What you can do with a computer
Data type
Can do
Software used
[Copy to PC]
[Write data to media]*
[Copy between media]*
[Easy editing]
Motion picture
HD Writer Ver1.0E for SD1
Standard Windows picture viewer or a
commercially available picture viewer
Playing back on a computer
Copying files to a computer
Still picture
Windows Explorer
Refer to P104 if using a Macintosh.
*Compatible media are SD card and discs (DVD-RAM, DVD-RW, DVD-R and DVD-R DL).
≥When you connect this unit and a computer, always insert the battery and connect the AC adaptor. If
you do not insert the battery and connect the AC adaptor, operation will not be possible after
connecting this unit to the computer.
≥We cannot guarantee operation of this unit if you use software other than that supplied to read/write
motion picture data to this unit.
92
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
Contents on provided CD-ROM
The following software applications are contained on the provided CD-ROM.
≥The software is the same as the software on the CD-ROM provided with Panasonic High Definition
Video Camera HDC-SD1.
ª HD Writer Ver1.0E for SD1
You can acquire data of motion pictures and still pictures on an SD card to the hard disk of the
computer, easily edit (split, merge, delete) the motion pictures, then write the data to an SD card or
disc.
[Copy to PC]:
If there is no more available memory on the SD card, copy the data to the hard disk of the computer.
You can then easily edit it (split or delete scenes etc.).
[Write data to media]:
You can copy motion picture data and still picture data from the hard disk of the computer to an SD
card. You can also copy motion picture data to a disc.
[Copy between media]:
You can copy motion picture data from an SD card to a disc or from a disc to an SD card.
[Easy editing]:
You can easily edit (split, merge, delete etc.) motion picture data that was copied to the hard disk of the
computer.
[Format disc]:
Depending on the type of disc that you use, formatting is necessary. Discs are formatted using the UDF
2.5 file system that supports the AVCHD.
ª DirectX
Microsoft DirectX 9.0c must be installed in order to operate the HD Writer Ver1.0E for SD1.
If DirectX is not already installed on your computer, you can install it from the CD-ROM. Click [DirectX]
and follow the on-screen messages to install it. If you install the software on a computer that is not
compatible with DirectX 9.0c, the computer may not work properly. If you are unsure whether or not
your computer is compatible, contact the maker of your computer.
93
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
Article 6 Limitation of Liability
End User License Agreement
The Software is provided “AS-IS” without
warranty of any kind, either expressed or implied,
including, but not limited to, warranties of
non-infringement, merchantability and/or fitness
for a particular purpose. Further, Matsushita
does not warrant that the operation of the
Software will be uninterrupted or error free.
Matsushita or any of its distributors or dealers will
not be liable for any damage suffered by
Licensee arising from or in connection with
Licensee’s use of the Software.
Before opening the CD-ROM package, please
read the following.
You (“Licensee”) are granted a license for the
Software defined in this End User Software
Agreement (“Agreement”) on condition that you
agree to the terms and conditions of this
Agreement. If Licensee does not agree to the
terms and conditions of this Agreement, promptly
return the Software to Matsushita Electric
Industrial Co., Ltd. (“Matsushita”), its distributors
or dealers from which you made the purchase.
Article 7 Export Control
Licensee agrees not to export or re-export to any
country the Software in any form without the
appropriate export licenses under regulations of
the country where Licensee resides, if
necessary.
Article 1 License
Licensee is granted the right to use the software,
including the information recorded or described
on the CD-ROM, instruction manuals, and any
other media provided to Licensee (collectively
“Software”), but all applicable rights to patents,
copyrights, trademarks and trade secrets in the
Software are not transferred to Licensee.
Article 8 Termination of License
The right granted to Licensee hereunder will be
automatically terminated if Licensee violates any
of the terms and conditions of this Agreement.
Upon such automatic termination, Licensee must
destroy the Software and related documentation
together with all the copies thereof at Licensee’s
own expense.
Article 2 Use by a Third Party
Licensee may not use, copy, modify, transfer or
allow any third party, whether free of charge or
not, to use, copy or modify the Software, except
as expressly provided for in this Agreement.
Article 3 Restrictions on Copying the Software
Licensee may make a single copy of the
Software in whole or in part solely for back-up
purposes.
Article 4 Computer
Licensee may only use the Software on a single
computer at a single location.
Article 5 Reverse Engineering, Decompiling or
Disassembly
Licensee may not reverse engineer, decompile,
or disassemble the Software, except to the
extent either of them is permitted under law or
regulation of the country where Licensee resides.
Matsushita, or its distributors or dealers will not
be responsible for any defects in the Software or
damage to Licensee caused by Licensee’s
reverse engineering, decompiling, or
disassembly of the Software.
94
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
Operating environment
≥A CD-ROM drive is necessary to install the supplied software applications. (A compatible drive and
media are necessary for writing to a DVD.)
≥When 2 or more USB devices are connected to a computer, or when devices are connected through
USB hubs or by using extension cables, proper operation is not guaranteed.
≥Use the supplied USB cable when connecting to the computer. (Operation is not guaranteed with any
other USB cables.)
≥Even if the system requirements mentioned in these operating instructions are fulfilled, some
computers cannot be used.
≥This software is not compatible with Microsoft Windows 3.1, Windows 95, Windows 98/98SE,
Windows Me and Windows NT.
≥Operation on an upgraded OS is not guaranteed.
ª Operating environment for HD Writer Ver1.0E for SD1
Personal computer
OS
IBM PC/AT compatible personal computer
Microsoft Windows 2000 Professional Service Pack 4
Microsoft Windows XP Home Edition Service Pack 2
Microsoft Windows XP Professional Service Pack 2
CPU
Intel Pentium III 1.0 GHz or higher (Intel Pentium 4 HyperThread
3.0 GHz or higher when a “Preview function” is used)
(including compatible CPU)
RAM
512 MB or more (1024 MB or more recommended)
Display
High Color (16 bit) or more (32 bit or more recommended)
Desktop resolution of 1024k768 pixels or more (1280k1024 pixels or
more recommended)
Graphics card complying with DirectX 9.0c, and DirectDraw Overlay
64 MB video memory or more
Free hard disk space
Necessary software
Ultra DMA — 100 or more
250 MB or more
≥When writing to a DVD, more than double the amount of free space as
the disc being created is necessary.
DirectX 9.0c
≥If you install the software on a computer that is not compatible with
DirectX 9.0c, the computer may not work properly. If you are unsure
whether or not your computer is compatible, contact the maker of your
computer.
Adobe Acrobat Reader 5.0 or later
Sound
DirectSound Support
Interface
USB port [Hi-Speed USB (USB 2.0)]
Mouse or equivalent pointing device
Other requirements
≥Supplied CD-ROM is available for Windows only.
≥Operation on an OS other than the one pre-installed is not guaranteed.
≥Operation is not guaranteed on computers that are not PC/AT compatible.
≥Input is not supported in languages other than English, French and Spanish.
≥Operation cannot be guaranteed on all DVD drives.
95
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
≥DVD discs authored with this software are not guaranteed to play in all DVD players that do not
support the AVCHD.
≥Operation is not guaranteed on Microsoft Windows XP Media Center Edition, Tablet PC Edition and
not compatible with 64 bit operation systems.
≥This software is not compatible with a multi-boot environment.
≥This software is not compatible with a multi-CPU environment.
≥If your computer does not satisfy the above system requirements, an error may occur when writing
data to disc.
≥Set the display resolution to 1024k768 (16 bits color) or higher.
Select [start] # ([Settings] #) [Control Panel] # ([Appearance and Themes] #) [Display] and select
[Settings] tab, and then adjust [Screen resolution] and [Color quality].
ª Operating environment for the card reader function (mass storage)
Personal computer
OS
IBM PC/AT compatible personal computer
Microsoft Windows 2000 Professional Service Pack 4
Microsoft Windows XP Home Edition
Microsoft Windows XP Professional
CPU
Intel Pentium III 450 MHz or higher/Intel Celeron 400 MHz or higher
128 MB or more (256 MB or more recommended)
USB port
RAM
Interface
Other requirements
Mouse or equivalent pointing device
≥The USB equipment operates with the driver installed as standard in the OS.
96
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
3 Click [Next].
Installation
When installing the software, log on to your
computer as the Administrator or with a user
name with equivalent authorization. (If you do not
have authorization to do this, consult your
manager.)
≥Before starting the installation, close any other
software applications which are running.
≥Do not perform any other operations on your
computer while the software is being installed.
4 Read carefully through the [End
User License Agreement], then
place a check beside [I accept
the terms of the license
Installing HD Writer Ver1.0E for
SD1
1 Insert the CD-ROM into the
agreement] if you agree to them
and click [Next].
computer.
The [Setup Menu] screen will appear.
≥If the [Setup Menu] screen does not
appear, double-click the CD-ROM drive
icon in [My Computer].
≥If you do not agree to the terms and
conditions of the License Agreement,
installation is not possible.
≥Continue to follow the on-screen messages
to install it.
2 Click [HD Writer Ver1.0E for
SD1].
5 After the installation is complete, restrictions
are displayed.
Check the contents, then click [t]
on the top right of the window.
≥The software application may not run
properly if you cancel the installation at any
point e.g. by pressing [Cancel].
≥Microsoft DirectX 9.0c must be installed in
order to operate the HD Writer Ver1.0E for
SD1. (l 93)
If you install the software on a computer
that is not compatible with DirectX 9.0c, the
computer may not work properly. If you are
unsure whether or not your computer is
compatible, contact the maker of your
computer.
97
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
6 Click [Finish].
Software application
uninstallation
Follow the steps below to uninstall any software
applications that you no longer require.
1 Select [start] # ([Settings] #)
[Control Panel] #
[Add or Remove Programs
(Applications)].
The computer must be rebooted for the
application to work.
Reading the operating
instructions of the software
applications
For details on how to use the software
applications, read the PDF operating
instructions.
≥You will need Adobe Acrobat Reader 5.0 or
later to read the PDF operating instructions.
2 Select [HD Writer Ver1.0E for
SD1], then click [Change/
Remove] ([Change or Remove] or
[Add/Remove]).
Select [start] #
[All Programs (Programs)] #
[Panasonic] # [HD Writer Ver1.0E
for SD1] # [Manual (PDF Format)].
≥Proceed with the uninstallation by following
the on-screen instructions.
≥After uninstalling the software, be sure to
reboot the computer.
98
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
3 Connect this unit and a
Connection and recognition
computer.
Connection and recognition
procedures
After the software applications are installed, this
unit must be connected to the computer and be
correctly recognized by the computer.
≥Connect after installing the software
applications.
≥Remove the supplied CD-ROM if it is inserted
in the computer. (If the [Setup Menu] screen is
displayed, wait until it finishes and then remove
the CD-ROM.)
A
A USB cable (supplied)
This unit is automatically recognized by the
computer.
≥Insert the plugs as far as they will go. The unit
and computer will not operate properly if the
plugs are not inserted fully.
≥Do not use any other USB connection cables
guaranteed with any other USB cables.)
≥If the recognition procedure is not
accomplished properly, operation will not be
possible after connecting the unit to the
computer.
≥If the unit fails to operate normally, it may mean
that you have not conducted the installation or
recognition procedure properly.
1 Insert the battery and connect
the AC adaptor.
≥When the unit is connected to a computer,
the operation mode cannot be changed and
its power cannot be turned off.
In this case, disconnect the USB cable
(l 101).
≥If you do not insert the battery and connect
the AC adaptor, operation will not be
possible after connecting this unit to the
computer.
≥When a computer is accessing the SD card in
2 Insert an SD card with recorded
this unit, the card access lamp lights. (When a
images in this unit and then set
card is being accessed,
appears on the
PC
the mode dial to
the power.
to turn on
LCD monitor.) Do not disconnect the USB
cable or AC adaptor while the card is being
accessed as it may damage the data.
≥It may be necessary to reboot the computer
after connecting this unit to it for the first
time.
99
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
ª Copying still pictures recorded
on the SD card to a computer
Card reader function (mass storage)
When an SD card with recorded data on it is
inserted into the unit and the unit is connected to
a computer using a USB cable, the SD card can
be used as an external drive so that still pictures
on the card can be copied to the computer with
Explorer or other programs.
About the computer display
When the unit is connected to a computer, it is
recognized as an external drive.
[Removable Disk] is displayed in [My Computer].
Example folder structure of an SD card:
1 Set the mode dial on the unit to
Removable Disk
PC
and connect the unit to the
DCIM
computer.
[Removable Disk] is displayed in [My
Computer].
100CDPFP
MISC
2 Double click the folder that
contains the files on the
removable disk ([DCIM] #
[100CDPFP]).
PRIVATE
AVCHD
AVCHDTN
BDMV
3 Drag and drop the files onto the
destination folder (on the
computer hard disk).
≥AVCHD format motion picture files
([00000.MTS] etc.) are saved in the [BDMV]
folder.
≥The motion picture thumbnails are recorded in
the [AVCHDTN] folder.
≥JPEG format still pictures ([IMGA0001.JPG]
etc.) are stored in the [100CDPFP] folder.
These can be opened with picture software that
supports JPEG pictures.
≥Up to 999 files can be recorded in the
[100CDPFP] or other such folder.
≥The DPOF setting files are recorded in the
[MISC] folder.
≥Do not use the computer to delete the SD
card’s folders. Otherwise, it may no longer be
possible for this unit to read the SD card.
≥Always use this unit to format SD cards.
≥When data not supported by this unit has been
recorded on a computer, it will not be
recognized by this unit.
We recommend HD Writer Ver1.0E for SD1
for copying motion picture data to and
from the SD card.
Using Windows Explorer or other
programs on the computer to copy, move
or rename files and folders recorded with
this unit will result in them being unusable
with HD Writer Ver1.0E for SD1.
100
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
2 Click the [Hardware] tab, then
To disconnect USB cable safely
1 Double click the icon in task
click [Device Manager].
tray displayed on the computer.
Hardware disconnect dialogue appears.
≥Depending on your computer’s settings,
this icon may not be displayed.
2 Select [USB Mass Storage
Device] and click [Stop].
3
Verify [MATSHITA HDC-SD1 USB
Device] is selected and click [OK].
Click [Close], and you can safely disconnect
the cable.
3 Verify the following items are
displayed.
≥Do not disconnect the USB cable while the card
access lamp is lit ( appears on the LCD
monitor) as it may damage the data.
Verifying the unit is correctly
recognized by the computer
To verify this unit is correctly recognized by the
computer, rotate the mode dial on this unit to
select PC connection mode, then connect the
unit to the computer with a USB cable and follow
the steps below.
ª If the driver has been recognized
properly
[USB Mass Storage Device] is displayed at
≥With some computers including those made by
NEC, the Device Manager may not be
displayed if a mode that places restrictions on
the functions has been established. Consult the
manufacturer or follow the steps in your
computer’s operating instructions to establish a
mode in which all the functions can be used,
then proceed with operation.
[Universal Serial Bus controllers].
ª If the driver has not been
recognized properly
[!] or [Unknown device] appears at [Universal
Serial Bus controllers] or [Other devices] etc.
(Where the display will appear depends on the
type of computer you are using.)
You can use the following methods to enable it to
be recognized.
Method 1: Turn off the unit and your computer
once and try verifying again.
Method 2: Remove the SD card and try verifying
again.
1 Select [start] # ([Settings] #)
[Control Panel] # ([Performance
and Maintenance] #) [System].
Method 3: Try connecting the unit to another
USB port on your computer.
101
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
3 Connect this unit and a
Using HD Writer Ver1.0E for
SD1
computer.
Using HD Writer Ver1.0E for SD1, you can copy
images recorded on this unit to the hard disk of
the computer. When you want to playback
images, write back the images from the hard disk
of the computer to an SD card. You can then
connect this unit to a TV to watch the images.
(l 80)
≥When using HD Writer Ver1.0E for SD1, log on
to your computer as Administrator with a login
name equally authorized. If you log on with a
login name other than Administrator, you
cannot use the applications.
A
A USB cable (supplied)
≥Insert the plugs as far as they will go. The
unit and computer will not operate properly
if the plugs are not inserted fully.
≥Do not use any other USB connection
cables except the supplied one. (Operation
is not guaranteed with any other USB
cables.)
There is no playback function on HD Writer
Ver1.0E for SD1. To play back the disc, use
commercially available playback software
that supports the AVCHD.
ª Copying data on an SD card to
the hard disk of the computer
4 (On the computer)
1 Insert the battery and connect
Select [start] #
the AC adaptor.
[All Programs (Programs)] #
[Panasonic] # [HD Writer Ver1.0E
for SD1] # [HD Writer].
≥If you do not insert the battery and connect
the AC adaptor, operation will not be
possible after connecting this unit to the
computer.
2 Insert an SD card with recorded
images in this unit and then set
PC
the mode dial to
the power.
to turn on
≥The HD Writer Ver1.0E for SD1
introductory screen is displayed. If [OK] is
clicked, the software will start.
5 Click the [Copy to PC] button.
102
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
6 Click the [Start copying] button.
2 Click
on the top right and
select the folder with the image
data you want to copy to the SD
card.
≥A confirmation message appears. Click
[Yes] and copying starts.
appears. If [Yes] is clicked, all the motion
will be deleted.
3 Select [Start writing] to copy the
images from the hard disk of the
computer to the SD card.
ª Writing back to an SD card
≥Insert an SD card in this unit and format the
card. (l 79)
(Use an SD card that can be used for motion
picture recording. (l 26))
Please be aware that if an SD card is
formatted, then all the data recorded on the
card will be erased. Store important data on a
computer etc.
≥Insert the battery and connect the AC
adaptor, then rotate the mode dial to select
≥A confirmation message appears. Click
[Yes] and copying starts.
PC
.
≥Connect this unit to the computer and start
HD Writer Ver1.0E for SD1.
≥Refer to the operating instructions of the
software (PDF file) for details on how to use it.
≥Do not insert a disc created with HD Writer
Ver1.0E for SD1 in a device that does not
support the AVCHD format. It may no longer be
possible to eject it. Also, the disc cannot be
played back on devices that do not support the
AVCHD format.
1 Click the [Write data to media]
button.
≥Some discs created with HD Writer Ver1.0E for
SD1 cannot be played on other devices, even if
they support the AVCHD. In such cases,
rewrite the motion pictures to the SD card and
play them back on this unit instead.
≥The menu screen created with HD Writer
Ver1.0E for SD1 does not appear on this unit.
Use a device that supports the AVCHD for
playback.
103
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
With a computer
If using Macintosh
≥Even if the system requirements mentioned in these operating instructions are fulfilled, some personal
computers cannot be used.
≥Apple, Mac OS is either registered trademarks or trademarks of Apple Computer, Inc. in the United
States and/or other countries.
≥PowerPC is a trademark of International Business Machines Corporation.
®
TM
®
TM
≥Intel Core Solo and Intel Core Duo are either registered trademarks or trademarks of Intel
Corporation in the United States and/or other countries.
ª Operating environment for the card reader function (mass storage)
Personal computer
Macintosh
OS
Mac OS X v10.3 to v10.4
CPU
PowerPC G3 (400 MHz or higher)
PowerPC G4
PowerPC G5
Intel Core Duo
Intel Core Solo
RAM
64 MB or more
USB port
Interface
≥The USB equipment operates with the driver installed as standard in the OS.
≥Supplied CD-ROM is available for Windows only.
ª Copying still pictures on PC
1 Connect this unit to the personal computer via the supplied USB cable.
2 Double-click [NO_NAME] or [Untitled] displayed on the desktop.
≥Files are stored in [100CDPFP] folder etc. in the [DCIM] folder.
3 Using a drag-and-drop operation, move the pictures you want to acquire
or the folder storing those pictures to any different folder on the personal
computer.
ª To disconnect USB cable safely
Drag [NO_NAME] or [Untitled] disk icon to the [Trash], and then disconnect the USB cable.
104
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª [SETUP]
[FORMAT CARD] (l 79)
[DISPLAY] (l 107)
[DATE/TIME] (l 41)
[DATE FORMAT] (l 41)
[POWER SAVE] (l 107)
[QUICK START] (l 33)
[BEEP SOUND] (l 107)
[LCD SET] (l 42)
Others
Menus and Indications
Menu list
Recording menus
[COMPONENT OUT] (l 84)
[HDMI RESOLUTION] (l 82)
[EZ Sync] (l 87)
[TV ASPECT] (l 80)
[INITIAL SET] (l 107)
[DEMO MODE] (l 107)
ª [BASIC]
[SCENE MODE] (l 63)
[D.ZOOM] (l 52)
[O.I.S.] (l 59)
ª [LANGUAGE] (l 42)
[GUIDE LINES] (l 59)
[CLOCK SET] (l 41)
ª [VIDEO]
[REC MODE] (l 47)
[FADE COLOR] (l 55)
[WIND CUT] (l 60)
[ZOOM MIC] (l 53)
[MIC LEVEL] (l 60)
[AGS] (l 44)
ª [PICTURE]
[FLASH LEVEL] (l 58)
[SHTR EFFECT] (l 50)
ª [ADVANCED]
[REC LAMP] (l 107)
[ZEBRA] (l 62)
[COLOR BAR] (l 62)
[MF ASSIST] (l 64)
105
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Playback menus
(motion picture playback)
Playback menus
(still picture playback)
ª [PLAY SETUP]
[PLAY MODE] (l 71)
ª [PLAY SETUP]
[SCENE PROTECT] (l 77)
[REPEAT PLAY] (l 71)
[RESUME PLAY] (l 72)
[SCENE PROTECT] (l 75)
[GUIDE LINES] (l 59)
[DPOF SET] (l 78)
ª [SETUP]
[FORMAT CARD] (l 79)
[DISPLAY] (l 107)
ª [SETUP]
[FORMAT CARD] (l 79)
[DISPLAY] (l 107)
[DATE/TIME] (l 41)
[DATE FORMAT] (l 41)
[POWER SAVE] (l 107)
[BEEP SOUND] (l 107)
[LCD SET] (l 42)
[DATE/TIME] (l 41)
[DATE FORMAT] (l 41)
[POWER SAVE] (l 107)
[BEEP SOUND] (l 107)
[LCD SET] (l 42)
[COMPONENT OUT] (l 84)
[HDMI RESOLUTION] (l 82)
[EZ Sync] (l 87)
[COMPONENT OUT] (l 84)
[HDMI RESOLUTION] (l 82)
[EZ Sync] (l 87)
[TV ASPECT] (l 80)
ª [LANGUAGE] (l 42)
[TV ASPECT] (l 80)
ª [LANGUAGE] (l 42)
106
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª [BEEP SOUND]
Menus related to [ADVANCED]
and [SETUP]
≥[OFF]
≥[ON]
This allows operations such as starting and
ending recording to be signaled by a beep.
When [OFF] is set, no beep is heard when an
operation such as recording is started or ended.
1 Beep
≥Underlined items are the initial shipping
condition.
ª [REC LAMP]
≥[OFF]
≥[ON]
When you start recording
The recording lamp lights during recording and
flashes when the unit receives a signal from the
remote control or when the self-timer is counting
down. When this is set to [OFF], it does not light
during recording.
When you turn on the power
When this unit is recognized by the computer or
the printer etc.
2 Beeps
When you pause recording
When you turn off the power
2 Beeps/4 times
ª [DISPLAY]
≥[OFF]
≥[ON]
When an error occurs e.g. recording not starting.
Check the sentence displayed on the screen.
(l 110)
The screen indications are selected as shown in
the illustration below.
ª [INITIAL SET]
[OFF]
≥[YES]
≥[NO]
When there is a menu that cannot be selected
due another function or mode being activated,
set to [YES] for changing the menu settings back
to the initial shipping condition.
(The language setting cannot be changed back
to the initial shipping condition.)
[ON]
30min
0h00m00s
HN
R30min
AUTO
ª [DEMO MODE]
15.12.2006
≥[OFF]
This item is used to start the unit demonstration.
(Only when the mode dial is at the position)
≥[ON]
ª [POWER SAVE]
≥[OFF]
≥[5 MINUTES]
If you set [DEMO MODE] to [ON] without
inserting an SD card, the demonstration
automatically starts. If any operation takes place,
the demonstration is canceled. However if no
operations take place for approx. 10 minutes, the
demonstration automatically starts again. To
stop the demonstration, set [DEMO MODE] to
[OFF] or insert an SD card. For normal use, set
[DEMO MODE] to [OFF].
[OFF]:
The power saving function is not activated.
[5 MINUTES]:
When about 5 minutes have passed without any
operation, this unit automatically turns off to
prevent the battery from running down. When
you use this unit, turn it on again.
≥In the following cases, the unit may not turn off
even when you set this to [5 MINUTES].
– When using the AC adaptor
– When connecting the unit to a computer or
printer via the USB cable
107
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
,
Fade (White), Fade (Black)
MagicPix function
Zoom microphone
Wind noise reduction
Microphone level
Zebra display
Indications
ª Recording indications
Motion picture recording
30min
0h00m00s
HN
R30min
MNL
MF
AWB
1
/
100
OPEN
0dB
,
,
Motion picture recording mode
Sports mode
HF
HN
HE
DEC 15 2007 3:30PM
5
Still picture recording
(when the PHOTO SHOT button is pressed
halfway)
Portrait mode
Low light mode
Spotlight mode
30min
0h00m00s
HN
R30min
Surf & snow mode
Auto white balance
MNL
MF
AWB
AWB
1
/
100
OPEN
0dB
Indoor mode (recording under
incandescent lamp)
MEGA
2.1Ｍ
100
Outdoor mode
Manual adjustment mode
Flash
Remaining battery power
Remaining battery time
30min
ß/ßA/
R30min
Remaining time for motion
picture recording
ßi/ßj
Flash level
Red eye reduction
Focus indication
0h00m00s
Elapsed recording time
± (White)
¥ (Green)
, Ø
DEC 15 2007 Date indication
3:30 PM
Time indication
Ø
Self-Timer recording
MEGA OIS
10
2
¥/; (Red)
; (Green)
Recording/writing to a card
Recording pause
MEGA
2.1Ｍ
Number of recording pixels for
still pictures
1920k1080
Auto mode
AUTO
MNL
MF
Manual mode
(White)
(Green)
(Red)
Card can be recorded to
Recognizing the card
Manual focus
10t
Zoom magnification indication
Backlight compensation
Recording/accessing the card
Still picture quality
,
Image stabilizer
Power LCD
Shutter speed
F number
100
Remaining number of still
pictures
1/100
OPEN, F2.0
0dB
Gain value
Soft skin mode
Tele macro
108
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª Playback indications
Motion picture playback
Number of recording pixels for
still pictures
2.1Ｍ
1920k1080
The picture size is not displayed for still
pictures recorded with other products that have
different picture sizes from the sizes shown
above.
Still picture playback
ª PC connection indications
Accessing the card (When
connected to a computer)
ª Confirmatory indications
–– (Time
display)
The built-in battery is low. (l 41)
1
Playback
;
Pause
°
The warning/alarm indication
appears when LCD monitor is
rotated towards the lens side.
Return the direction of the LCD
monitor to normal position and
check the warning/alarm
indication.
5/6
7/8
Cue/Review playback
Last/first scene paused
Skip playback
9/:
D/E
Slow motion playback
Frame-by-frame playback
Playback time
;1/2;
0h00m00s
No SD card is inserted/unusable
card.
Play mode
All scenes
Scenes recorded on the
selected date
No.10
Scene number
Volume adjustment
Repeat playback
Resume playback
15
100-0001
PictBridge
1
Still picture folder/file number
display
When a printer compatible
with PictBridge is connected
DPOF already set
(to more than 1)
Protected still pictures
109
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Messages
CANNOT RECORD.
NO DATA.
Data writing to the SD card has failed.
There are no motion pictures or still pictures recorded on the SD
card.
If this message appears although data is recorded on the SD card,
the condition of the card is probably not stable.
Turn off the power and then turn it on again.
CANNOT BE USED DUE
The recording format is different so it cannot be used. Save the data
TO INCOMPATIBLE DATA.
on the SD card to a computer, then use the SD card after formatting
it.
CANNOT RECORD -
INCOMPATIBLE CONTROL
DATA.
CHECK CARD.
This card is not compatible or it cannot be recognized by the unit.
THIS CARD CANNOT
RECORD IN VIDEO MODE.
An 8 MB or 16 MB SD card on which motion pictures cannot be
recorded is inserted.
CARD LOCKED.
NOW ACCESSING.
PLEASE DO NOT REMOVE
CARD.
The data is being processed. Close the card slot cover and wait for
a while.
CARD FULL.
The SD card is full so no further data can be recorded. Delete
unnecessary scenes/files or insert a new SD card. (l 34, 74, 76)
CANNOT RECORD.
THE NUMBER OF SCENES
HAS EXCEEDED THE
MAXIMUM LIMIT.
reached so recording is not possible. Delete unnecessary scenes or
insert a new SD card. (l 34, 74, 76)
CANNOT RECORD - DATE
CAPACITY IS FULL.
The number of scenes grouped together on a date has reached the
maximum number so recording is not possible. Delete unnecessary
scenes or insert a new SD card. (l 34, 74, 76)
CANNOT OPERATE.
TEMPERATURE IS HIGH.
PLEASE TURN OFF AND
WAIT A WHILE.
Turn off the power, wait until the temperature falls and then turn on
the power again.
THIS BATTERY CANNOT
BE USED.
Use a battery that is compatible with this unit. (l 30)
You are attempting to connect an AC adaptor not compatible with
this unit. Use the supplied AC adaptor. (l 31)
If using a Panasonic battery compatible with this unit (l 30),
remove the battery and then insert it again. If the message appears
even after repeating this several times, this unit needs repair.
Detach the power and consult the dealer who you purchased this
unit from. Do not attempt to repair it by yourself.
110
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
CANNOT PROTECT.
Scenes on SD cards for which the top menu has been created with
HD Writer Ver1.0E for SD1 cannot be protected. (l 75)
AGS MODE ON-REC
PAUSED
The AGS function is activated. (l 44)
PUSH THE RESET
SWITCH.
An irregularity in the unit has been detected. Press the RESET
button to restart the unit. (l 118)
CANNOT SET.
The [GUIDE LINES], [ZEBRA], [MF ASSIST] and [MIC LEVEL]
menu settings cannot be set when the color bar is set.
CHANGE MODE TO USE
USB.
The USB cable is connected in recording mode.
DISCONNECT USB
CABLE.
You are attempting to switch the mode dial from PC Connection
mode to another mode with the USB cable connected.
PLEASE CONNECT AC
ADAPTOR AND BATTERY.
You are attempting to connect to a computer in PC Connection
mode when the AC adaptor is not connected or the battery is not
inserted.
RECONNECT USB CABLE. Disconnect the USB cable, then connect the AC adaptor with the
battery inserted in this unit and reconnect the USB cable.
DISCONNECT USB
CABLE.
The unit cannot correctly establish the connection to the computer
or printer. Disconnect and then reconnect the USB cable.
DISCONNECT USB
CABLE.
When the unit is connected to a computer, its power cannot be
turned off.
111
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
About recovery
When the SD card is accessed, you try to playback a scene or faulty control information is read, one of
the messages below may be displayed. (Depending on the error, this may take time.)
CONTROL DATA ERROR HAS BEEN
DETECTED.
When connecting to AC adaptor or the remaining capacity of the battery is enough:
[FINISHED.]
When the remaining capacity of the battery is low:
[PLEASE CONNECT AC ADAPTOR OR CHANGE BATTERY.]
THUMBNAIL DATA ERROR IS
DETECTED.
When connecting to AC adaptor or the remaining capacity of the battery is enough:
[THUMBNAIL DATA HAS BEEN REPAIRED SUCCESSFULLY.]
When the remaining capacity of the battery is low:
[PLEASE CONNECT AC ADAPTOR OR CHANGE BATTERY.]
≥Use a sufficiently charged battery or the AC adaptor.
≥Depending on the condition of the data, it may not be possible to completely repair the data.
≥If the recovery fails, you will no longer be able to playback the scenes recorded before the power went
off.
≥When data recorded on another device is recovered, it may not be possible to play back the data on
this unit or the other device.
≥If the recovery fails, format the SD card on this unit.
≥If the thumbnail information is recovered, displaying the thumbnails may become slower.
112
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Functions that cannot be used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s specifications.
The table below shows examples of functions restricted by various conditions.
Functions
Conditions which disable the functions
Backlight compensation
≥When the MagicPix function is used
≥When the iris/gain is set
MagicPix (Set and cancel)
Soft skin mode (Set and cancel)
Tele macro (Set and cancel)
Help mode
≥While recording
Shutter effect
≥While recording motion pictures
Flash
≥While recording motion pictures
≥When the MagicPix function is used
Zoom
≥When the PHOTO SHOT button is pressed halfway
Zoom microphone
Wind noise reduction
Scene mode
≥An external microphone is used
≥When setting the AUTO/MANUAL/FOCUS switch to
AUTO
≥When the MagicPix function is used
MF assist function
≥When digital zoom (12k or higher) is used
Change of white balance
≥When digital zoom (12k or higher) is used
≥When the MagicPix function is used
Adjusting the shutter speed, iris/gain
≥When the MagicPix function is used
≥When the scene mode is used
113
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
ª Unit operations
Problem
Check points
≥Is the battery fully charged?
# Charge it with the AC adaptor. (l 28)
≥The battery protection circuit may have operated. Attach the battery
to the AC adaptor for 5 to 10 seconds. If the unit still cannot be
used, the battery is faulty.
This unit cannot be
turned on.
≥Is the LCD monitor open?
This unit is turned off
automatically.
≥If you do not use the unit for approximately 5 minutes, the power is
automatically turned off to conserve the battery charge. To resume
recording, turn the power back on.
function (l 107) is set to [OFF].
≥Are you connecting to a TV compatible with EZ Sync with a HDMI
cable?
# If you connect to a TV compatible with EZ Sync with a HDMI
the TV, the power on this unit also turns off. If you are not using
EZ Sync, set [EZ Sync] to [OFF]. (l 88)
This unit does not stay
on long enough.
≥Is the battery low?
# If the remaining battery power indication is flashing or the
down. Charge the battery. (l 28)
A clicking sound is heard ≥This is the sound of the lens moving and is not a defect. This sound
when the unit is shaken.
will no longer be heard when the unit’s power is turned on.
Battery runs down
quickly.
≥Is the battery fully charged?
# Charge it with the AC adaptor. (l 28)
≥Are you using the battery in an extremely cold place?
# The battery is affected by ambient temperature. In cold places,
the operating time of the battery becomes shorter.
≥Has the battery worn out?
# The battery has a limited life. If the operating time is still too short
even after the battery is fully charged, the battery has worn out
and can no longer be used.
The minute display of the
remaining battery power
indication is not
≥The remaining battery capacity indication is an approximation.
If you think the remaining battery capacity indication is not displayed
correctly, fully charge the battery, discharge it and then charge it
again. (Even if this operation is performed, it may not be possible to
display the remaining battery capacity correctly if the battery was
used for a long period of time where the temperature was low or
high or if the battery was repeatedly charged.)
displayed correctly.
114
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Problem
Check points
This unit cannot be
operated though
powered up.
≥The unit cannot be operated if the LCD monitor is not opened.
≥Press the RESET button. (l 118) If normal conditions are not
and then reconnect the battery or AC adaptor. Then about 1 minute
later, turn on the power again. (Conducting the above operation
while the card is being accessed may damage the data on the
SD card.)
This unit does not
operate normally.
The remote control does
not function.
≥Has the button-type battery of the remote control run out?
# Replace it with a new button-type battery. (l 25)
The screen has changed
suddenly.
≥Has the demonstration started?
# If you set [DEMO MODE] to [ON] without inserting an SD card in
recording mode, the demonstration automatically starts.
Normally this should be set to [OFF]. Press the MENU button,
then select [SETUP] # [DEMO MODE] # [OFF] and press the
cursor button.
A function indication
such as the remaining
time indication or the
elapsed time indication is
not shown.
≥If you set [SETUP] > [DISPLAY] > [OFF], indications other than
warnings and date indications disappear.
Recording does not start
although power is
supplied to this unit and
the SD card is correctly
inserted.
≥Has the SD card’s write protect switch been set to LOCK?
# No recording is possible while the write protect switch is set to
LOCK. (l 27)
≥Is the memory of the SD card full?
# If there is no more available memory, free up some memory by
deleting unnecessary scenes or use a new SD card. (l 34, 74,
76)
≥Is the unit set to recording mode?
≥Is the card slot cover open?
.
# If the card slot cover is open, this unit may not operate normally.
The unit arbitrarily stops
recording.
≥Can the SD card be used for motion picture recording?
# Use an SD card that can be used for motion picture recording.
(l 26)
≥Is the AGS function activated?
# Record in the normal horizontal position or set [AGS] to [OFF].
(l 44)
115
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Problem
Check points
≥Is manual focus mode selected?
# Set the AUTO/MANUAL/FOCUS switch to AUTO.
≥Are you trying to record a scene which is hard to bring into focus in
auto focus mode?
Auto focus function does
not work.
# There are some recording subjects and surroundings for which
the auto focus does not operate correctly. (l 124) If so, use the
Recorded still pictures
are not clear.
≥Are you trying to record small or finely detailed objects with
[PICT. QUALITY] set at [
[PICT. QUALITY] set at [ ], the images may break up into a
]?
mosaic-like pattern. Record with [PICT. QUALITY] set at [
]
instead. (l 51)
Sound is not played back
from the built-in speaker
of this unit.
≥Is the volume too low?
# During playback, move the volume lever to display the volume
indication and adjust it. (l 70)
Sound is played back
from one side of
speakers when motion
pictures recorded on this
unit are played back on
another device.
≥The internal microphones of this unit record sound with Dolby Digital
5.1 Creator. When the sound is played back on another device, if
stereo 2 channel speakers on TV are used, the sound may be
played back from one side of the speakers.
When the TV has surround sound effect function, we recommend
using it.
Refer to the operating instructions of the TV for how to operate the
surround sound effect.
Although this unit is
correctly connected to a
TV, images cannot be
seen.
≥Does the input switch on the TV match the connected terminal?
# Please read the operating instructions of your TV and select the
channel that matches the input used for the connection.
≥Is the [TV ASPECT] setting correct?
# Change the setting to match the aspect ratio of the TV.
Press the MENU button, then select [SETUP] # [TV ASPECT]
# [16:9] or [4:3] and press the cursor button.
The images are squeezed
horizontally.
≥Are the HDMI and component cables connected to the unit while in
recording or PC connection mode?
# If both HDMI and component cables are to be connected, set the
unit to playback mode.
116
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Problem
Check points
Scenes cannot be
deleted.
≥Is the scene on the SD card protected?
# Protected scenes cannot be deleted. Release the protect setting.
(l 75)
displayed as
) cannot be deleted. If the scenes are
aware that if a card is formatted then all the data recorded on the
card will be erased.
≥Is the file on the SD card protected?
# Protected files cannot be deleted. Release the protect setting.
(l 77)
≥If the SD card’s write protect switch is set to LOCK, then deletion is
disabled. (l 27)
The images on the SD
card do not look normal.
≥The data may be destroyed. It may have been destroyed by static or
electromagnetic waves. Store important data on a computer or other
products as well.
Even if an SD card is
formatted, it cannot be
used.
dealer. Use an SD card from 8 MB to 4 GB with this unit.
If the SD card is inserted
in this unit, it is not
recognized.
# Use this unit to format SD cards. Please be aware that if an SD
card is formatted, then all the data recorded on the card will be
erased. (l 79)
If the SD card is inserted
in another device, it is not
recognized.
≥Check that the device is compatible with the capacity or type of SD
card (SD Memory Card/SDHC Memory Card) that you inserted.
(l 26)
# Refer to the operating instructions of the device for details.
The indication
disappears.
≥Is this unit connected to a computer?
# No operation can be performed on this unit when it is connected
to a computer.
The screen is frozen.
≥Turn off the power to this unit. If the power cannot be turned off,
press the RESET button, or remove the battery or AC adaptor and
then reattach it. After that, turn on the power again. If normal
operation is still not restored, detach the power connected, and
consult the dealer who you purchased this unit from.
No operation can be
performed.
117
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Problem
Check points
“PUSH THE RESET
SWITCH.” is displayed.
≥The unit has automatically detected an error. Press the RESET
button with the projecting part of the grip belt A. This will restart the
unit.
1A
≥If you do not press the RESET button, the power to this unit is
turned off automatically about 1 minute later.
≥Even after you press the RESET button, the indication may still
appear repeatedly. If so, this unit needs repair. Detach the power
connected, and consult the dealer who you purchased this unit
from. Do not attempt to repair the unit by yourself.
118
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª When connected to another device
Problem
Check points
EZ Sync does not work.
≥Are you connecting with the component cable or the AV cable?
# Connect with a HDMI cable (optional). (l 87)
≥Is the [EZ Sync] setting appropriate?
# Press the MENU button, then select [SETUP] # [EZ Sync] #
[ON] with the cursor button.
≥Depending on HDMI terminal of the TV, the input channel may not
switch automatically. In this case, use the remote control for the TV
to switch input. (For details on how to switch input, please read the
operating instructions for the TV.)
≥Check the EZ Sync setting on the connected device.
≥Turn the power to the unit off and then back on again.
≥Set [Ctrl with HDMI] to [Off] on the TV and then turn it back to [On].
(Refer to the operating instructions of the TV for details.)
With the EZ Sync on, the
power to the unit does
not turn off even if the TV
is turned off.
≥Is the mode dial on the unit set to PC connection mode?
# EZ Sync does not work with the unit in PC connection mode.
ª With a computer
Problem
Check points
Even if connected by the
USB cable, this unit is not
recognized by the
computer.
≥Have you set this unit to the correct mode?
# This unit is not recognized in recording/playback mode. Set it to
PC connection mode.
≥Is the battery inserted and the AC adaptor connected?
# Insert the battery and connect the AC adapter when connecting
this unit on the computer.
≥Select another USB terminal on the computer.
≥Check the operating environment. (l 95)
≥Turn the power to the unit off and then back on again and reconnect
the USB cable.
When the USB cable is
disconnected, an error
message will appear on
the computer.
≥To disconnect the USB cable safely, double-click the
task tray and follow the instructions on the screen.
icon in the
Cannot playback a disc
written to with HD Writer
Ver1.0E for SD1.
≥There is no playback function on HD Writer Ver1.0E for SD1. To
play back the disc, use commercially available playback software
that supports the AVCHD.
Cannot see the PDF
operating instructions for
HD Writer Ver1.0E for
SD1.
≥Is Adobe Acrobat Reader 5.0 or later installed in the computer you
are using?
# You will need Adobe Acrobat Reader 5.0 or later to read the PDF
operating instructions for HD Writer Ver1.0E for SD1.
119
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Do not spray insecticides or volatile
chemicals onto the unit.
Cautions for use
≥If the unit is sprayed with such chemicals, its
body may be marred and the surface finish may
peel off.
About this unit
The unit and the SD card become warm during
use. This is not a malfunction.
≥Do not leave rubber or plastic products in
contact with the unit for a long time.
Keep the High Definition Video Camera as far
away as possible from electromagnetic
equipment (such as microwave ovens, TVs,
video games etc.).
When you use the unit in a sandy or dusty
place such as a beach, do not let sand or fine
dust get into the body and terminals of the
unit.
≥If you use the High Definition Video Camera on
top of or near a TV, the pictures and sound on
the High Definition Video Camera may be
disrupted by electromagnetic wave radiation.
≥Do not use the High Definition Video Camera
near cell phones because doing so may result
in noise adversely affecting the pictures and
sound.
Also, keep the unit away from sea water.
≥Sand or dust may damage the unit. (Care
should be taken when inserting and removing a
card.)
≥If sea water splashes onto the unit, wipe off the
water with a well wrung cloth. Then wipe the
unit again with a dry cloth.
≥Recorded data may be damaged, or pictures
may be distorted, by strong magnetic fields
created by speakers or large motors.
≥Electromagnetic wave radiation generated by
microprocessors may adversely affect the High
Definition Video Camera, disturbing the
pictures and sound.
When carrying the unit, do not drop or bump
it.
≥A strong impact can break the unit’s casing,
causing it to malfunction.
Do not use benzine, paint thinner or alcohol
for cleaning the unit.
≥If the High Definition Video Camera is
adversely affected by electromagnetic
equipment and stops functioning properly, turn
the High Definition Video Camera off and
remove the battery or disconnect AC adaptor.
Then reinsert the battery or reconnect the AC
adaptor and turn the High Definition Video
Camera on.
≥Before cleaning, detach the battery or pull out
the AC cable from the AC outlet.
≥The camera body may be discolored and the
surface finish may peel off.
≥Wipe the unit with a soft dry cloth to remove
dust and fingerprints. To remove stubborn
stains, thoroughly wring a cloth that has been
soaked in a neutral detergent diluted with water
and wipe the unit with it. Afterwards, wipe it
with a dry cloth.
Do not use the High Definition Video Camera
near radio transmitters or high-voltage lines.
≥If you record near radio transmitters or
high-voltage lines, the recorded pictures and
sound may be adversely affected.
≥When you use a chemical dust cloth, follow the
instructions that came with the cloth.
Do not use the unit for surveillance purposes,
etc.
Make sure to use the supplied cords and
cables. If you use optional accessories, use
the cords and the cables supplied with them.
Do not extend the cords and the cables.
≥If you use the unit for a long time, heat will build
up inside it and this may cause a malfunction.
When you are not going to use the unit for an
extended time
≥When storing the unit in a cupboard or cabinet,
it is recommended that you place a desiccant
(silica gel) in with it.
120
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
If you drop the battery accidentally, check to
see if the terminals are damaged.
≥Attaching a battery with damaged terminals can
damage the unit or AC adaptor.
About the battery
The battery used in this unit is a rechargeable
lithium-ion battery. It is susceptible to humidity
and temperature and the effect increases the
more the temperature rises or falls. In cold areas,
the full charge indication may not appear or the
low battery indication may appear about
Do not throw old battery into fire.
≥Heating a battery or throwing it into a fire may
result in an explosion.
5 minutes after starting use. At high
temperatures, the protection function may be
triggered, making it impossible to use the unit.
If the operating time is very short even after
the battery has been recharged, the battery
has worn out. Please purchase a new battery.
Be sure to detach the battery after use.
≥If the battery is left attached, a minute amount
of current continues to flow even if the unit’s
power is off. Keeping the unit in this state may
result in over discharge of the battery. This may
result in you not being able to use the battery
even after it is charged.
≥The battery should be stored in the vinyl bag so
metal does not come into contact with the
terminals.
About the AC adaptor
≥If the temperature of the battery is extremely
high or extremely low, charging may take time
or the battery may not be charged.
≥If the charging lamp keeps flashing, make sure
that the terminals of the battery or the AC
adaptor are not exposed to dirt, foreign objects
or dust, then reconnect them properly.
Disconnect the AC cable from the AC outlet
when you remove dirt, foreign objects or dust
on the terminals of the battery or the AC
adaptor.
If the charging lamp is still flashing, something
may be wrong with the battery or AC adaptor.
Contact your dealer.
≥If you use the AC adaptor near a radio, radio
reception may be disturbed. Keep the AC
adaptor 1 m (3.3 feet) or more away from the
radio.
≥The battery should be stored in a cool place
free from humidity, with as constant
temperature as possible. (Recommended
temperature: 15 °C to 25 °C (59 °F to 77 °F),
Recommended humidity: 40% to 60%)
≥Extremely high temperatures or low
temperatures will shorten the life of the battery.
≥If the battery is kept in high-temperature,
high-humidity, or oily-smoky places, the
terminals may rust and cause malfunctions.
≥To store the battery for a long period of time,
we recommend you charge it once every year
and store it again after you have completely
used up the charged capacity.
≥When using the AC adaptor, it may generate
whirring sounds. However, this is normal.
≥After use, be sure to disconnect the AC
adaptor. (If it is left connected, a minute amount
of current is consumed.)
≥Dust and other matter attached to the battery
terminals should be removed.
≥Always keep the electrodes of the AC adaptor
and battery clean.
Prepare spare batteries when going out for
recording.
Put this unit near the outlet to make it easy
for the interrupting device (plug) to reach it.
≥Prepare batteries enough to last for 3 to 4 times
the period during you want to record pictures in.
In cold places such as a ski resort, the period
during which you can record pictures is
shortened.
≥When you travel, do not forget to bring an AC
adaptor so that you can recharge the batteries
at your destination.
121
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
About the SD card
LCD monitor
≥The memory capacity indicated on the label of
an SD card is the total of the capacity for
copyright protection and management and the
capacity which can be used on the unit, a
computer etc.
≥When the LCD monitor gets dirty, wipe it with a
dry soft cloth.
≥In a place with drastic temperature changes,
condensation may form on the LCD monitor.
Wipe it with soft dry cloth.
≥During prolonged use, the unit’s surfaces and
the SD card will heat up slightly. This is normal.
≥When the unit has become very cold, for
example due to storage in a cold area, its LCD
monitor will be slightly darker than usual
immediately after the power is turned on. The
normal brightness will be restored when the
unit’s internal temperature rises.
Always set the mode dial to OFF when
inserting or removing an SD card.
While this unit accesses the SD card (while
or
is being displayed/the access
Extremely high precision technology is
employed to produce the LCD Monitor screen
featuring a total of approximately 251,000
pixels. The result is more than 99.99%
effective pixels with a mere 0.01% of the
pixels inactive or always lit. However, this is
not a malfunction and does not affect the
recorded picture.
lamp is lit), do not remove the SD card,
operate the mode dial, turn off the power or
shake or impact the unit.
About the miniSD Card
≥Be sure to insert miniSD Cards in the dedicated
card adaptor before use. Inserting a card in this
unit without the adaptor may damage the unit
or the card.
≥Do not insert an empty card adaptor in this unit.
Do not leave the adaptor in this unit while
inserting or removing miniSD Cards. This may
cause the unit to malfunction.
122
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Explanation of terms
About condensation
Automatic white balance
When condensation forms on the unit, the lens
will cloud up and the unit may not work properly.
Make every effort to ensure that condensation
does not form. If it does form, take the actions
described below.
White balance adjustment recognizes the color
of light and adjusts so the white color will
become a purer white. The unit determines the
hue of light that comes through the lens and
white balance sensor, thereby judging the
recording condition, and selects the closest hue
setting.
This is called automatic white balance
adjustment.
However, since the unit only stores white color
information under several light sources,
automatic white balance adjustment does not
function normally under other light sources.
Causes of condensation
Condensation takes place when the ambient
temperature or humidity is changed as
follows.
≥When this unit is brought inside from the cold
(e.g. a ski slope) to a warm room.
≥When this unit is moved from an
air-conditioned car to outside.
≥When a cold room has been warmed up
quickly.
2)
10 000K
9
8
000K
000K
3)
7
6
000K
000K
≥When cool wind from an air conditioner is
directly blown onto this unit.
4)
5)
5
4
000K
000K
≥After summer afternoon showers of rain.
≥When this unit is in a very humid place where
the air is thick with steam. (e.g. a heated
swimming pool)
6)
1)
7)
3
000K
8)
When this unit is taken to a location with a
significant temperature difference such as
from a cold place to a hot place.
9)
2
1
000K
000K
10)
If, for example, you have used this unit for
recording on a ski slope and are taking it into a
heated room, place the unit inside a plastic bag,
remove as much of the air from inside the bag as
possible, then seal the bag. Leave the unit for
about an hour in the room so the temperature of
the unit is close to the ambient temperature of
the room, then use it.
The illustration above shows the range over
which the auto white balance functions.
1) The effective range of automatic white
balance adjustment on this unit
2) Blue sky
3) Cloudy sky (rain)
4) TV screen
5) Sunlight
6) White fluorescent lamp
7) Halogen light bulb
8) Incandescent light bulb
9) Sunrise or sunset
10) Candlelight
What to do with the lens is fogged
up.
Remove the battery or AC adaptor and leave the
unit for about 1 hour. When the unit becomes
close to the ambient temperature, the fog
disappears naturally.
123
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Outside of the effective range of automatic white
balance adjustment, the image will become
reddish or bluish. Even within the effective range
of automatic white balance adjustment, the
automatic white balance adjustment may not
function properly if there is more than one light
source. For light outside the functional automatic
white balance adjustment range, use the manual
white balance adjustment mode.
Recording a subject behind dirty or dusty
window
The subject behind the window will not be
focused because the focus is on the dirty
window.
Similarly, when recording something on the
opposite side of a road with heavy traffic, a
vehicle that happens to pass by may be brought
into focus.
Recording a subject that is surrounded by
objects with glossy surfaces or by highly
reflective objects
Since whatever is shiny or glistens is brought into
focus, it is hard to focus on the subject to be
recorded. The focus may become blurry when
recording subjects at the beach, in night views or
in scenes involving fireworks or special lights.
White balance
The images recorded by the unit may become
bluish or reddish under the influence of certain
light sources. To avoid such phenomena, adjust
the white balance.
White balance adjustment determines the white
color under different light sources. By
recognizing which is the white color under
sunlight and which is the white color under a
fluorescent light, the unit can adjust the balance
among the other colors.
Recording a subject in dark surroundings
The unit cannot focus correctly because the light
information that comes through the lens
decreases considerably.
Since the white color is the reference for all the
colors (that make up light), the unit can record
pictures in a natural hue if it can recognize the
reference color white.
Recording a fast-moving subject
As the focus lens-inside moves mechanically, it
cannot keep up with a fast-moving subject.
When, for example, recording a sports event with
fast moving subjects, the focus may lose its
sharpness.
Auto focus
The lens is moved forward or backward
automatically to bring the subject into focus.
Auto focus has the following characteristics.
≥Adjusts so that the vertical lines of a subject are
seen more clearly.
≥Attempts to bring an object with higher contrast
into focus.
Recording a subject with little contrast
It is easy to bring subjects with a sharp contrast
or vertical lines or stripes into focus. This means
that a subject with little contrast, such as a white
wall, may become blurry because the unit
achieves focus based upon the vertical lines of
an image.
≥Focuses on the screen center only.
Due to these characteristics, auto focus does not
work correctly in the following situations. Record
pictures in the manual focus mode.
Recording distant and close-up objects at the
same time
Since the unit focuses on whatever is at the
center of the screen, it is difficult to bring the
background into focus when close-up objects are
placed in focus. When recording people with
distant mountains in the background, you cannot
focus on both the subject which is close-up and
the objects which are in the distance.
124
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Specifications
High Definition Video Camera
Information for your safety
Power source:
DC 9.3 V (When using AC adaptor)
DC 7.2 V (When using battery)
Recording: 8.0 W
Power consumption:
Signal system
Recording format
Image sensor
1080/60i
AVCHD format compliant
1/4z 3CCD image sensor
Total: 560 Kk3
Effective pixels:
Motion picture: 520 Kk3
Still picture: 520 Kk3
Lens
Auto Iris, F1.8 to F2.8
Focal length:
4.0 mm to 48.0 mm
Macro (Full range AF)
Filter diameter
Zoom
43 mm
12k optical zoom, 30k/700k digital zoom
3z wide LCD monitor (approx. 251 K pixels)
5.1 channel surround microphone (with a zoom function)
1 round speaker ‰ 20 mm
Monitor
Microphone
Speaker
White balance
adjustment
Auto tracking white balance system
Standard illumination
1,400 lx
Minimum required
illumination
Approx. 6 lx (1/60 in Low light mode)
Approx. 2 lx with the MagicPix function
Video output level
1.0 Vp-p, 75 h
125
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Component terminal
output level
Y: 1.0 Vp-p, 75 h
Pb: 0.7 Vp-p, 75 h
Pr: 0.7 Vp-p, 75 h
HDMI terminal output
level
HDMI Ver. 1.2a [1125i (1080i)/525p (480p)]
Audio output level (Line)
Mic input
316 mV, 600 h
Mic sensitivity j50 dB (0 dB=1 V/Pa, 1 kHz)
(‰ 3.5 mm stereo mini jack)
USB
Card reader/writer function (No copyright protection support)
Hi-Speed USB (USB 2.0), USB terminal Type miniB
PictBridge-compliant
Flash
Available range: Approx. 1.0 m to 2.5 m (3.3 feet to 8.2 feet)
Dimensions
74.1 mm (W)k67.0 mm (H)k137 mm (D)
[2.9 q (W)k2.6 q (H)k5.4 q (D)]
(excluding projecting parts)
Mass
Approx. 430 g (Approx. 0.95 lbs.)
(without supplied battery and an SD card)
Mass in operation
Operating temperature
(with supplied battery and an SD card)
0 °C to 40 °C (32 °F to 104 °F)
(0 °C to 30 °C (32 °F to 86 °F) when connected to the computer)
Operating humidity
10% to 80%
See page 30
Battery operation time
Motion pictures
Recording media
SD Memory Card:
256 MB, 512 MB, 1 GB, 2 GB (FAT12 and FAT16 system compliant)
SDHC Memory Card:
4 GB (FAT32 system compliant)
Compression
MPEG-4 AVC/H.264
Recording mode and
transfer rate
: Approx. 13 Mbps (CBR)
: Approx. 9 Mbps (VBR)
: Approx. 6 Mbps (VBR)
HF
HN
HE
Audio compression
Dolby Digital (Dolby AC3), 5.1 ch
126
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Still pictures
Recording media
SD Memory Card:
8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB
(FAT12 and FAT16 system corresponding)
SDHC Memory Card:
4 GB (FAT32 system corresponding)
Compression
Picture size
JPEG (Design rule for Camera File system, based on Exif 2.2
standard), DPOF corresponding
1920k1080
AC adaptor
Information for your safety
Power source:
Power consumption:
DC output:
AC 110 V to 240 V, 50/60 Hz
19 W
DC 9.3 V, 1.2 A (Unit operation)
DC 8.4 V, 0.75 A (Battery charging)
Dimensions
Mass
92 mm (W)k33 mm (H)k61 mm (D)
[3.6 q (W)k1.3 q (H)k2.4 q (D)]
Approx. 115 g (Approx. 0.25 lbs.)
Battery pack
Information for your safety
Maximum voltage:
Nominal voltage:
Rated capacitance:
DC 8.4 V
DC 7.2 V
1320 mAh
Specifications may change without prior notice.
127
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Others
Optional accessories
The optional accessories are the same as for the Panasonic High Definition Video Camera
HDC-SD1.
Accessory No.
Figure
Description
VW-AD21PP-K
AC adaptor with AC Cable and DC Cables
VW-VBG130*
1320 mAh/Rechargeable Lithium Ion Battery Pack
RP-SDR01GU1A
RP-SDR512U1A
Class 2 1 GB SD Memory Card
Class 2 512 MB SD Memory Card
RP-SDM04GU1K
RP-SDM02GU1A
Class 4 4 GB SDHC Memory Card
Class 4 2 GB SD Memory Card
RP-SDV04GU1K
RP-SDV02GU1A
RP-SDV01GU1A
Class 6 4 GB SDHC Memory Card
Class 6 2 GB SD Memory Card
Class 6 1 GB SD Memory Card
*Please refer to page 30, concerning the battery charging time and available recording time.
NOTE: Accessories and/or model numbers may vary by country. Please consult your local
dealer.
128
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Limited Warranty (For USA Customers)
PANASONIC BROADCAST &
TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC
CORPORATION OF NORTH
AMERICA
PANASONIC PUERTO RICO INC.
Ave. 65de Infanteria, Km.9.5 San Gabriel
Industrial Park
Carolina, Puerto Rico 00985
One Panasonic Way 2A-4 Secaucus, NJ 07094
Limited Warranty
Panasonic Broadcast & Television Systems Company or Panasonic Sales Company (collectively
referred to as “the Warrantor”) will repair this product and all included accessories with new or
refurbished parts, free of charge in the USA or Puerto Rico, from the original date purchase in the event
of a defect in materials or workmanship as follow:
Warranty
Part Warranty
Labor Warranty
All Monitors, VCRs, Cameras,
Camcorders, P2 Product, DVDs,
Plasma Displays, switchers and
Plug-in Computers.
1 Year
1 Year
Exceptions
90 days or
500 Hours
90 days or
500 Hours
D3 & D5 Video Heads
Camera CCD
Monitor CRT
2 Years
2 Years
1 Year
1 Year
All Accessories Including batteries,
cables, and tapes.
10 Days
None
Carry-in or mail-in service in the USA may be obtained during the warranty period by contacting a
Panasonic Broadcast & Television Systems Company Authorized Service Center either by using the
website
http://www.panasonic.com/support/
or by calling toll free 1-800-526-6610 to locate the nearest authorized Service Center.
Carry-in or mail-in service in Puerto Rico can be obtained during the warranty period by calling
787-750-5135.
This warranty is extended only to the original purchaser and is non
transferable. A purchase receipt or other proof of date of original purchase will be required before
warranty service is rendered.
This warranty only covers failures due to defects in materials or workmanship, which occur during
normal use. The warranty does not cover damage which occur in shipping or failures which are caused
by products not supplied by the warrantor, or failures which result from faulty installation, set-up
adjustments, improper antenna, inadequate signal pickup, maladjustment of user controls, improper
operation, power line surge, improper voltage supply, lighting damage, or service by anyone other than
an authorized repair facility, or damage that is attributable to acts of God.
129
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITATION, DAMAGE TO MEDIA) RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above exclusions or limitations may nor apply
to you. This warranty gives you specific legal rights and you may also have other rights, which vary
from state to state.
If you have a problem with this product that is not handled to your satisfaction, then write the Consumer
Affairs Department at the Company address indicated above.
IN THE USA
FOR THE NEAREST SERVICE CENTER
CALL 1-800-526-6610
FOR TECHNICAL SUPPORT
CALL 1-800-524-1448
OR
OR
Website: http://www.panasonic.com/support/
Email: [email protected]
REGISTER YOUR PRODUCT
WWW.PANASONIC.COM/REGISTER
IN PUERTO RICO
FOR SERVICE CALL 787-750-5135
130
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
LIMITED WARRANTY STATEMENT (For Canadian Customers)
Panasonic Canada Inc. (also known as PCI) warrants this product to be free of defects in material and
workmanship under normal use during the applicable warranty coverage period described below. PCI
agrees to repair, or at its option, exchange, any part that becomes defective. However, the product
must be purchased and serviced in Canada. The product or part that shows evidence of defect must be
delivered prepaid or carried in to an authorized Panasonic Broadcast Service Center. This warranty
does not cover shipping costs.
The warranty coverage period is one year for both parts and labour beginning with the date of original
end user purchase, subject to the exceptions as stated below. Repaired or replacement parts supplied
during the warranty coverage period carry the unexpired portion of the original warranty coverage
period. Proof of product purchase is a condition of warranty service. The owner must produce the
product purchase receipt or other satisfactory evidence of date of original purchase.
This warranty does not apply to external appearance items, such as handles, knobs, safety windows,
etc. This warranty does not apply to any part, or parts, of the product, installed, altered, repaired or
misused in any way that, in the opinion of PCI, affects the reliability of or detracts from the performance
of the product.
For products requiring routine preventive maintenance, that maintenance must be performed in order to
maintain warranty coverage.
Serial numbers that have been altered, defaced or removed void this warranty. This warranty does not
cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the
control of PCI.
Marking or retained images (sometimes called “burn-in”) resulting from the display of fixed images on
video display products are not defects and are not covered under this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions
may not be applicable.
Warranty Service
If the product needs to be shipped for service, carefully pack (preferably in the original carton) and
enclose a letter, detailing the complaint. Send prepaid and adequately insured to the local authorized
Panasonic Service Centre in your area or to Panasonic Technical Support and Product Services
Department, 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location
requires a return authorization before shipment. No liability is assumed for loss or damage to the
product while in transit.
WARRANTY COVERAGE PERIOD EXCEPTIONS
Item
Colour Camera CCD Imaging Block 2 years
SD Cards (Content not covered)
Parts
Labour
1 year
N/A
≥Dust, smoke, rental/staging environment and twenty-four/seven operation, dramatically decreases the
interval between performances of routine preventive maintenance required to maintain this warranty
coverage.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, ON L4W 2T3
131
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Others
Index
ª Numerics
ª A
Lens hood ...................................................... 23
Menu list ...................................................... 105
Microphone terminal ...................................... 21
Mode dial ....................................................... 32
Motion picture playback ................................. 68
Motion picture recording ................................ 45
A/V terminal .......................................21, 84, 86
Aperture .........................................................66
Auto focus ....................................................124
Auto Ground-Directional Standby (AGS) .......44
AVCHD ..........................................................13
ª B
Backlight compensation .................................54
Battery cable cover ........................................22
Beep sound ..................................................107
ª C
Color bar ........................................................62
Component ....................................................84
Cooling fan .....................................................19
Cursor button .................................................35
ª D
Date and time setting .....................................41
Delete
Number of Recordable Pictures
ª O
Scene ....................................................74
Demo mode .................................................107
Digital zoom ...................................................52
Display .........................................................107
Dubbing .........................................................89
ª E
ª F
Fade ...............................................................54
Flash ..............................................................57
Format
ª P
PictBridge ...................................................... 90
POWER LCD ................................................. 42
Power save .................................................. 107
Protecting scenes .......................................... 75
Protecting still pictures .................................. 77
Card .......................................................79
Frame-by-frame playback ..............................70
ª G
Gain ...............................................................66
Grip belt .........................................................23
Guide line function .........................................59
132
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª R
Recording lamp ............................................107
Recording modes ...........................................47
Recording time elapsed .................................46
Red eye reduction ..........................................58
Remaining battery capacity indication ...........31
Remaining number of still pictures .................49
Remaining time left for recording ...................46
Repair ..........................................................112
Repeat playback ............................................71
ª S
Scene mode ...................................................63
SD Memory Card ...........................................26
SDHC Memory Card ......................................26
Self-recording ................................................53
Simultaneous recording .................................50
Skip playback .................................................69
Slow-motion playback ....................................69
Soft skin mode ...............................................56
Still picture (JPEG) playback .........................72
Still picture compatibility ................................73
ª T
Tele macro .....................................................56
Tripod receptacle ...........................................23
TV aspect .......................................................80
ª V
Volume adjustment ........................................70
ª W
White balance ........................................65, 124
Wind noise reduction function ........................60
ª Z
Zebra display .................................................62
Zoom ..............................................................52
Zoom microphone ..........................................53
133
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Others
ª Extracción de la batería
1) Abra la tapa de la batería.
Spanish Quick Use Guide/Guía
española para el uso rápido
ª Carga de la batería
A
2) Extraiga la batería.
≥Deslice A en la dirección de la flecha para
desbloquearlo y luego extraiga la batería.
1) Conecte el cable de CA al adaptador de
CA y a la toma de CA.
2) Instale la batería en el compartimiento
alineando la marca y, a continuación,
conéctela de forma segura.
A
≥La clavija de salida del cable de CA no
queda completamente conectada al
conector del adaptador de CA. Como se
muestra en A, queda un espacio.
3) Cierre la tapa de la batería.
ª Inserción de la batería
1) Abra la tapa de la batería.
≥Empuje A mientras lo desliza.
ª Cómo encender la unidad
Mientras pulsa el botón de desbloqueo,
PC
ajuste el selector de modo en
,
o
.
≥Gire el selector de modo mientras pulsa el
botón de desbloqueo A si cambia de OFF a
otro modo.
≥Alinee con el indicador de estado B.
A
B
2) Inserte la batería hasta escuchar un clic
prestando atención al sentido de la
batería.
A
ª Cómo apagar la unidad
B Empuje la batería hasta que queda
bloqueada.
Coloque el selector de modo en OFF.
B
3) Cierre la tapa de la batería.
134
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
4) Vuelva a pulsar el botón de inicio/parada
de grabación para hacer una pausa en la
grabación.
ª Insertar/extraer una tarjeta SD
1) Ajuste el selector de modo en la posición
OFF.
2) Abra la pantalla LCD y luego abra la tapa
de la ranura de la tarjeta.
ª Grabación de fotografías (JPEG)
1) Gire el selector de modo para seleccionar
.
3) Inserte/extraiga la tarjeta SD de la ranura
de la tarjeta.
2) Abra la pantalla LCD.
3) Pulse el botón PHOTO SHOT hasta la
mitad para ajustar el enfoque. (Solo para
enfoque automático)
A
≥Para insertar una tarjeta SD, colóquela con
el lado de la etiqueta A hacia arriba e
insértela derecho hacia dentro, hasta que
tope.
4) Cierre la tapa de la ranura de la tarjeta de
forma segura.
ª Grabación de películas
1) Gire el selector de modo para seleccionar
.
4) Pulse el botón PHOTO SHOT
completamente para sacar la foto.
2) Abra la pantalla LCD.
3) Pulse el botón de inicio/parada de
grabación para iniciar la grabación.
135
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
ª Reproducción de películas
ª Reproducción de fotografías
1) Gire el selector de modo para seleccionar
.
(JPEG)
1) Gire el selector de modo para seleccionar
.
2) Pulse el cursor hacia arriba y luego hacia
la izquierda para seleccionar la ficha
(reproducción de películas).
2) Pulse el cursor hacia arriba y luego hacia
la derecha para seleccionar la ficha
(reproducción de fotografías).
A
A
A Ficha reproducción de películas
3) Seleccione la escena que desea
reproducir.
A Ficha de reproducción de fotografías
3) Select the file to be played back.
B
C
B
C
D
D
E
B Página anterior
B Página anterior
C Página siguiente
D Número de escena
4) Pulse el cursor.
C Página siguiente
D Indicación de número de archivo
E Nombre carpeta/archivo
4) Pulse el cursor.
5) Mueva el cursor para realizar una de las
siguientes operaciones.
5) Mueva el cursor para realizar una de las
siguientes operaciones.
1/;:
Reproducción/
Pausa
1/;: Iniciar o hacer una pausa en la
presentación de diapositivas
(reproducción de las fotografías
contenidas en la tarjeta SD en orden
numérico).
6 (Mover y sostener): Revisión
5 (Mover y sostener): Localización
∫:
Detener la
reproducción y
visualizar las
miniaturas.
E:
D:
∫:
Reproducir la imagen anterior.
Reproducir la imagen siguiente.
Detener la reproducción y visualizar
las miniaturas.
136
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
137
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
138
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
139
VQT1F36
Download from Www.Somanuals.com. All Manuals Search And Download.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7196
Southeast Region: (201) 348-7162
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:
One Panasonic Way 2E-10, Secaucus, NJ 07094 (201) 348-7587
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
P
VQT1F36
S0207Tj0
C
© 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|