Remote Interactive Dock
Contents
DS-A2X
Instruction Manual
Thank you for purchasing an Onkyo product.
Please read this manual carefully before making
any connections or using this product.By follow-
ing these instructions, you’ll get the best audio
performance and the most listening pleasure
from your Onkyo product. Keep this manual for
future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is ille-
gal without the permission of the copyright
holder.
For Canadian Models
NOTE:THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
Modèle canadien
2. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a
soft cloth dampened with a weak solution of
mild detergent and water. Dry the unit immedi-
ately afterwards with a clean cloth. Don’t use
abrasive cloths, thinners, alcohol, or other chem-
ical solvents, because they may damage the fin-
ish or remove the panel lettering.
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003 DU
CANADA.
For some models
Before use,connect the appropriate AC plug adapter
to the AC adapter.
3. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your
hands are wet or damp. If water or any other liq-
uid gets inside this unit, have it checked by your
Onkyo dealer.
The type of plug adapter depends on the place of
purchase.
Disconnect
Connect
For U.S. models
FCC Information for User
CAUTION:
Notch
The user changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the equip-
ment.
NOTE:
For European Models
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
This equipment generates,uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions,may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the fol-
lowing measures:
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
•
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV
technician for help.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
About the RI Dock
Package Contents
With the Onkyo RI Dock,you can easily play the
Make sure you have the following items:
*
*
music stored on your Apple iPod through
your Onkyo audio system and enjoy great
sound, and watch iPod slideshows and videos
on your TV. In addition, the onscreen display
(OSD) allows you to view, navigate, and select
your iPod’s playlists (artists, albums, songs,
genres, composers) on your TV, and with the
supplied remote controller, you can control
your iPod from the comfort of your sofa.
• AC adapter (1.4 m,
4.59 feet)
• DS-A2X Remote
Interactive Dock
Adapter varies from
country to country.
, which stands for Remote Interactive, is an
exclusive Onkyo control system that allows all
-capable Onkyo audio components to be
turned on or off together,and your amp to turn
on automatically and select the appropriate
input source when playback is started on a
source component.It also allows you to control
your iPod with your amp’s remote controller.
• AV cable (1.8 m,
5.90 feet)
•
cable (1.7 m,
5.57 feet)
In this manual, the DS-A2X Remote Interactive
Dock is referred to as the“RI Dock.”
• Remote controller
with button-type
battery (CR 2025)
• Instruction manual
Features
❑ Play your iPod music through your Onkyo
audio system and enjoy great sound
❑ View, navigate, and select your iPod’s
playlists (artists, albums, songs, genres,
composers) on your TV
Compatible iPods
■ Made for:
❑ Control your iPod from the comfort of
your sofa with the supplied remote con-
troller
•
•
•
5th Generation iPod (iPod with video)
iPod photo (iPod with color display)
4th Generation iPod
❑ Watch iPod videos and slideshows on your
TV
•
•
2nd Generation iPod nano
1st Generation iPod nano
❑ Supports all iPods with an iPod connector,
except 3rd generation iPods
•
iPod mini
❑ Charges your iPod’s battery while you
enjoy your music
Note:
•
3rd generation iPods are not sup-
ported.
•
Before using the RI Dock, update your
iPod with the latest software, available
from the Apple Web site at:
For the latest information on the RI Dock, see
*
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started—Continued
Getting to Know the RI Dock
iPod adapter
RI MODE switch
Set it to match your amp’s
input display (see below).
Remote control
sensor
iPod connector
HDD
iPod slot
TAPE
MD
CDR
or
DOCK
Amp input
display
VIDEO OUT jack
jack
MD
TAPE
CD-R
HDD/DOCK
MD
TAPE
CD-R
HDD/DOCK
MD
TAPE
CD-R
HDD/DOCK
MD
TAPE
CD-R
HDD/DOCK
TAPE
MD
CDR
HDD/DOCK
RI MODE switch
See your amp’s instruction manual for details on changing the
input display. On some amps, you press and hold the [TAPE]
button to change the input display from TAPE to MD, CDR, HDD
or DOCK.
AUDIO OUT L/R jacks
DC IN 5V 1A jack
To control your iPod with your amp’s
remote controller, select the matching
remote control mode.
Amp remote
controller’s mode
■ Adjusting the iPod Adapter
The iPod adapter needs to be adjusted to
match your particular iPod. Insert your
iPod into the RI Dock. If there’s a gap
between the back of your iPod and the
adapter, turn the adapter counterclock-
wise to close the gap.Turning the adapter
counterclockwise moves it forward.Turn-
ing it clockwise moves it backward.
Forward
Backward
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started—Continued
Remote Controller
D Play/Pause [
/
] button
Starts or pauses playback of the selected
song.
E Previous and Next [
]/[
] buttons
The Previous [ ] button selects the previ-
ous track. During playback it selects the
beginning of the current track.The Next
1
2
9
[
] button selects the next track.
3
4
J
K
Press and hold the Previous [
rewind. Press and hold the Next [
ton to fast forward.
] button to
] but-
F SHUFFLE button
5
6
Sets the Shuffle function to Songs, Albums,
or Off.
L
M
G PLAYLIST/PAGE MODE [ ]/[ ] buttons
Used to select the page modes.During play-
back or when the OSD mode is set to Off,
they select playlists.
7
8
H ALBUM/PAGE [ ]/[ ] buttons
Used to page through the playlists (artists,
albums, songs, genres, composers) dis-
played on your TV.During playback or when
the OSD mode is set to Off, they select
albums.
I RESUME button
Used to resume playback. It has no function
when the OSD mode is set to Off.
J SELECT button
Used to select songs and menus on the
onscreen display and iPod.
K Up and Down arrow [ ]/[ ] buttons
Used to navigate songs and menus on the
onscreen display and iPod.
Remove the plastic film before using
the remote controller.
L REPEAT button
Sets the Repeat function to One, All, or Off.
A SETUP button
M VOLUME [ ]/[ ] buttons
Adjust the volume on the Onkyo amp or AV
receiver.They don’t affect the iPod’s volume
setting.
Used to set the TV system (PAL/NTSC) and
the remote controller’s ID.
B MODE button
Sets the OSD mode to On or Off.
C MENU button
Used to select the previous menu on the
onscreen display and iPod.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started—Continued
Replacing the Battery
Aiming the Remote Controller
Use only a battery of the same type (CR 2025).
When using the remote controller, point it
toward the RI Dock’s remote control sensor, as
shown below.
1. To open the battery compartment, press
the small hollow and slide open the cover.
Remote control sensor
2. While pressing the tab as shown, slide out
RI Dock
the old battery.
Slide the new battery into the battery com-
partment with the positive side facing up.
Notes:
•
If the RI Dock is placed on top of another
component, the remote controller’s sig-
nal may be obstructed and the remote
controller may not work reliably.
3. Slide the cover shut.
•
The remote controller may not work reli-
ably if the RI Dock is subjected to bright
light, such as direct sunlight or inverter-
type fluorescent lights. Keep this in mind
when installing.
•
If another remote controller of the same
type is used in the same room, or the RI
Dock is installed close to equipment that
uses infrared rays, the remote controller
may not work reliably.
Notes:
•
If the remote controller doesn’t work reli-
ably, try replacing the battery.
•
If you intend not to use the remote con-
troller for a long time,remove the battery
to prevent damage from leakage or cor-
rosion.
•
•
•
Don’t put anything on top of the remote
controller, such as a book or magazine,
because a button may be pressed contin-
uously, thereby draining the batteries.
The remote controller may not work reli-
ably if the RI Dock is installed in a rack
behind colored glass doors. Keep this in
mind when installing.
•
An expired battery should be removed as
soon as possible to prevent damage from
leakage or corrosion.
Caution: Replacing the battery incorrectly
may cause an explosion. Use only a battery
of the same type or an equivalent.
The remote controller will not work if
there’s an obstacle between it and the RI
Dock’s remote control sensor.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started—Continued
Hooking Up the RI Dock
Depending on the Onkyo amp that you’re
using, choose connection method A or B.
Note: When the AC adapter is unplugged or
not connected to the RI Dock, the RI Dock
A: Connect the RI Dock’s AUDIO OUT L/R jacks
and VIDEO OUT jack to an RI Dock-compati-
ble input on your Onkyo amp. (You might
need to change the input display to“HDD”
or“DOCK.”)
will output no sound or video,
functions
will not work,and your iPod’s battery will not
be charged.
B: Connect the RI Dock’s AUDIO OUT L/R jacks
to the TAPE (MD, CDR) IN jacks on your
Onkyo amp. And connect the RI Dock’s
VIDEO OUT jack directly to your TV.
Caution: Connect the supplied
cable to
only
jacks. Do not connect headphones
jack, as it will damage your equip-
to the
ment.
See your amp’s instruction manual for details.
■ If you’ve connected the RI Dock’s AUDIO
OUT L/R jacks to your amp’s TAPE (MD,
CDR) IN jacks and also want to connect
the RI Dock’s VIDEO OUT jack to your amp
AC adapter
5
Connect the RI Dock’s VIDEO OUT jack to an
unused video input on your amp.
Wall outlet
When you want to watch an iPod slideshow or
video, select the video input source first, and
then select the TAPE (MD, CDR) input source.
Your AV receiver will output the audio being
fed to the TAPE (MD, CDR) input, and because
the video source doesn’t change when the
TAPE input source is selected, it’ll continue to
output the video being fed to the video input.
Supplied
Supplied AV cable
cable
White
AUDIO
INPUT
Red
L
R
VIDEO
INPUT
VIDEO
INPUT
■ What to do if you already have a compo-
nent connected to your amp’s RI Dock-
compatible input
Yellow
Yellow
TV
-capable amp
or
Connect the RI Dock to an unused AV input on
your amp. However, you will not be able to use
1. Using the supplied AV cable, connect the RI
Dock’s AUDIO OUT L/R jacks to a suitable
audio input on your amp. And connect the
RI Dock’s VIDEO OUT jack to a video input
on your Onkyo AV receiver (A) or TV (B).
The input you use depends on the type of
Onkyo amp you have. See your amp’s
instruction manual for details.
any of the
functions.
2. Using the supplied
RI Dock’s jack to an
cable, connect the
jack on one of
the Onkyo components in your system.
3. Connect the supplied AC adapter to the RI
Dock’s DC IN jack.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RI Dock
Setting the OSD Mode
Controlling Your iPod without the OSD
Set the OSD (onscreen display) mode before
you start using the RI Dock.
To control your iPod without the OSD, set the
OSD mode to Off,and use the remote controller
1. Plug in the AC adapter.
2. Turn on your TV and amp, and select the
Controlling Your iPod with the OSD
appropriate inputs on your TV and amp.
3. Insert your iPod into the RI Dock.
When the OSD mode is set to On and your iPod
is inserted in the RI Dock, playlists (artists,
albums, songs, genres, composers) will be dis-
played on your TV.
Remove your
iPod’s case
■ Playing Songs
4. Use the remote controller’s
[MODE] button to set the
OSD mode.
1. Use the Up and Down arrow [ ]/[ ] but-
tons to select Playlists, Artists, Albums,
Genres, Songs or Composers, and then
press the [SELECT] button.
On: Playlists (artists, albums, songs, genres,
composers) are displayed on your TV,
and you can navigate and select your
music while looking at your TV.While
this mode is selected, your iPod dis-
plays the Onkyo logo.
Off: Nothing is displayed on your TV and
you navigate and select your music by
using your iPod’s display.
Notes:
•
•
•
To prevent iPod connector damage,don’t
twist your iPod when inserting or remov-
ing it, and be careful not to knock over
the RI Dock while your iPod is inserted.
Don’t use the RI Dock with any other iPod
accessories, such as FM transmitters and
microphones, because they may cause a
malfunction.
Top Menu
2. Use the Up and Down arrow [ ]/[ ] but-
tons and [SELECT] button to select a song,
and press the Play/Pause [
start playback.
/
] button to
When selecting songs, use the [MENU] but-
ton to go back to the previous menu.
You can’t change the OSD mode while
watching an iPod slideshow or video.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RI Dock—Continued
■ Using the Page Modes
Repeat mode
Shuffle mode
With the page modes, you can quickly locate
your favorite songs even when your song lists,
artist lists, and so on are very long.There are
four page modes:L, M, S, and P. These stand for
Large, Medium, Small, and Page.In P mode, you
can page through the list consecutively. In the
S, M, and L modes, you can page through the
list in progressively larger steps.
Playback status
1. Use the PAGE MODE Up and Down [ ]/[
]
buttons to select a page mode.
Depending on the size of the list, it may not
be possible to change the page mode.
2. Use the PAGE Up and Down [ ]/[ ] but-
tons to page up or down the list.
Playback time
Total time
Shuffle modes
Repeat modes
Song shuffle
All repeat
First song on First song on the Page mode
Album shuffle
One-track repeat
the next page
previous page
Note:
■ Resume Function
•
While playing a playlist, you can use the
PLAYLIST Up and Down [ ]/[ ] buttons
to select other playlists.While playing an
album, you can use the ALBUM Up and
Down [ ]/[ ] buttons to select other
albums.
With the Resume function, you can resume
playback of the song that was playing when
you removed your iPod from the RI Dock or
changed the OSD mode to Off.
1. Select and play a song displayed on your TV.
2. During playback or while playback is
paused, remove your iPod from the RI Dock
or change the OSD mode to Off.The current
song is remembered.
■ Song Shuffle
You can play all of the songs in your iPod in ran-
dom order.
3. When you reinsert your iPod into the RI
Dock (set the OSD mode to On), press the
[RESUME] button to resume playback of the
remembered song.
•
Press the [MENU] button repeatedly to
select the top menu, and use the Up and
Down arrow [ ]/[ ] buttons to select
“Shuffle Songs,”and then press the [SELECT]
button.
Notes:
•
•
•
The Resume function can be used only
when the OSD mode is set to On.
If the AC adapter is disconnected, the
remembered song will be forgotten.
If the Resume function is used during
shuffle playback, when the iPod is rein-
serted in the RI Dock, playback will
resume with any song.
■ Now Playing
During playback, you can display information
about the current song.
•
Press the [MENU] button repeatedly to
select the top menu, and use the Up and
Down arrow [ ]/[ ] buttons to select“Now
Playing,”and then press the [SELECT] but-
ton.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RI Dock—Continued
TV Display Settings
Other Functions
When the OSD mode is set to On, you can
change the background color and set the
screen saver.
■
Functions
Depending on your amp, you may also be able
to use the following functions.
1. Press the [MENU] button repeatedly to
Note:
select the top menu.
•
Your amp may take several seconds to
startup, so you might not hear the first
few seconds of the first song.
2. Use the Up and Down arrow [ ]/[ ] but-
tons to select“Settings,”and then press the
[SELECT] button.
3. Use the Up and Down arrow [ ]/[ ] but-
tons to select Background Color or Screen
Saver, and then press the [SELECT] button.
• System On Function
When you turn on your amp, the iPod turns on
as well.With some amps, you may need to
press the [ON] button on your amp’s remote
controller’s twice to turn on the other compo-
nents in your system.
4. Use the Up and Down arrow [ ]/[ ] but-
tons to select an option, and then press the
[SELECT] button.
■ Background Color
• System Off Function
When you turn off your amp, the iPod turns off
as well.
You can change the background color of the
onscreen display on your TV to any one of the
following eight colors: None (black), Blue1,
Blue2, Green1, Green2, Magenta, Red1, or
Red2.
*
• Auto Power On Function
If you start iPod playback while your amp is on
Standby, your amp will automatically turn on
and select your iPod as the input source.Then,
your iPod will start playback.
■ Screen Saver
You can set the time at which the screen saver is
activated to any one of the following four
options:1 minute, 5 minutes, 10 minutes, or Off
(screen saver off).
*
• Direct Change Function
If you start iPod playback while listening to
another input source, your amp will automati-
cally select your iPod as the input source.
When the screen saver activates, the onscreen
display on yourTV disappears.Press any button
on the remote controller to cancel the screen
saver and resume the onscreen display.
• Timer Play
You can use your amp’s Timer function to turn
on your amp and iPod and start playback at a
specified time.
• Linked Dimmer Operation
Setting the TV System
When you use your amp’s Dimmer function to
change its display’s brightness, the brightness
of the RI Dock’s Power indicator will change as
well.
While the OSD mode is set to On, you can set
the RI Dock’s video output to PAL or NTSC.
If the onscreen display looks distorted on your
TV, try changing the TV system.
• Using Your Amp’s Remote Controller
You can use your amp’s remote controller to
control basic iPod functions (see page 13).
•
While pressing and holding down the
[SETUP] button, press the VOLUME Up [
button for more than 3 seconds to select
]
NTSC, or press the VOLUME Down [ ] but-
ton for more than 3 seconds to select PAL.
*
If you use your iPod’s controls to start an iPod slideshow or
video, these functions will not work, so use the remote con-
troller instead.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RI Dock—Continued
■ Charging Your iPod’s Battery
Operating Notes:
The RI Dock charges your iPod’s battery while
your iPod is in the RI Dock.
•
The RI Dock must be connected to your
amp with both an
cable to use the
cable and an audio
functions.
Notes:
•
To charge your iPod battery, the AC
adapter must be plugged into a suitable
wall outlet and connected to the RI
Dock’s DC IN jack.
•
If your amp doesn’t support the System
On, System Off, Auto Power On, and
Direct Change functions, you’ll need to
turn your amp on and off and select the
input source manually.
•
See your iPod’s instruction manual for
more information on battery charging.
•
Before you select another input source,
stop iPod playback to prevent your amp
from selecting the iPod input source by
mistake.
•
•
If any accessories are connected to your
iPod, your amp may not be able to select
the input source properly.
Setting the Remote Controller’s ID
If you cannot adjust the volume of your Onkyo
component with the DS-A2X’s remote control-
ler, try changing its remote control ID.The
default setting is #1.
While your iPod is in the RI Dock, its vol-
ume control has no effect. If you adjust
your iPod’s volume control while it’s in the
RI Dock, make sure it’s not set too high
before you reconnect your headphones.
Some Onkyo components are set to ID #2 or #3.
•
While pressing and holding down the
[SETUP] button, press one of the following
buttons for more than 3 seconds to set the
ID:
■ Using Your iPod’s Alarm Clock
ID #1: PLAYLIST Up [ ] button
ID #2: ALBUM Up [ ] button
ID #3: PLAYLIST Down [ ] button
ID #4: ALBUM Down [ ] button
You can use your iPod’s Alarm Clock function to
automatically turn on your iPod and amp at a
specified time.Your amp’s input source will
automatically be set to the input to which your
iPod is connected.
Notes:
•
This function only works when the OSD
mode is set to Off.
•
To use this function, your iPod must be in
the RI Dock, and the RI Dock must be con-
nected to your amp with both an
cable and an audio cable.
•
•
When you use this function,be sure to set
your amp’s volume control to a suitable
level.
Your amp may take several seconds to
startup, so you might not hear the first
few seconds of the first song.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RI Dock—Continued
Using Your Amp’s Remote Controller
The following table shows which buttons on your amp’s remote controller you can use to control
your iPod while it’s in the RI Dock. Be sure to select the appropriate remote mode first, and point
your remote controller at your amp. Note that some buttons may be labelled differently, and some
remote controllers may not have certain buttons.
Remote controller button to use
iPod function
Turn on/off
Play
Description
iPod is turned on and off.
TAPE mode MD mode CDR mode HDD mode
[STANDBY], [ON]
—
Starts playback on the iPod. If the iPod is not
already on, it’s turned on automatically.
Play [
]
Pause
Pause [ ], Stop [
]
Pause [
]
Pauses iPod playback.
[
[
],
]
Next song
Next [
]
Selects the next iPod song.
Restarts the current iPod song. Press it twice to
select the previous song.
[
[
],
]
Previous song
Previous [
]
—
Fast forward
Rewind
Fast Forward [
Rewind [
]
Press and hold to fast forward the iPod.
Press and hold to rewind the iPod.
—
]
* To select the next or previous photo in an iPod photo slideshow, use the controls on your iPod photo.
The following functions can be used with some Onkyo amps.
Remote controller button to use
iPod function
Shuffle
Description
TAPE mode MD mode CDR mode HDD mode
[DOLBY
Sets the iPod’s Shuffle function to: Songs,
Albums, or Off.
[RANDOM], [PLAYMODE], [SHUFFLE]
MODE]
[REVERSE
[REPEAT]
MODE]
Sets the iPod’s Repeat function to: One, All, or
Off.
Repeat
Backlight
REC [
]
[DISPLAY], [SCROLL]
The iPod’s backlight comes on for 30 seconds.
To use the next four functions with modes
other than HDD, first select Playlist/Album
mode by using one of these buttons, and then
press the listed button while“Playlist/Album
mode”is displayed on your TV (about 5 sec-
onds).
Playlist/Album
mode
Reverse
Play [
[ENTER], [PROGRAM],
[MEMORY]
—
]
[PLAYLIST Selects the next playlist on the iPod.
UP] Select Playlist/Album mode first (see above).
Next playlist
Fast Forward [
]
Previous
playlist
[PLAYLIST Selects the previous playlist on the iPod.
DOWN] Select Playlist/Album mode first (see above).
Rewind [
Next [
]
[ALBUM Selects the next album on the iPod.
Next album
]
UP]
Select Playlist/Album mode first (see above).
Previous
album
[ALBUM Selects the previous album on the iPod.
DOWN] Select Playlist/Album mode first (see above).
Previous [
]
* Depending on your amp, some buttons may not work as expected.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
•
The TAPE IN on some amps can be set to TAPE,MD,
or CDR. Make sure the RI Dock’s RI MODE switch
setting and the remote control mode match this
setting. See your amp’s manual for more informa-
tion.
If you still can’t control your iPod,start playback by
pressing your iPod’s Play button. Remote opera-
tion should then be possible.
■ There’s no sound
•
•
Make sure your iPod is actually playing.
Make sure your iPod is inserted properly in the RI
Dock.
•
•
Make sure the RI Dock is connected to the correct
input jacks on your amp. Do not connect it to any
output jacks.
Make sure your amp is turned on,the correct input
source is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way.
Make sure the AC adapter is connected to a suit-
able wall outlet and connected to the RI Dock.
Try resetting your iPod.
•
Make sure your amp’s remote controller is set to
the correct remote control ID.
•
•
■ The onscreen display doesn’t appear on
your TV
•
•
•
Set the OSD mode to On (see page 9).
Try setting the TV system to PAL or NTSC (see
■ The RI Dock’s remote controller doesn’t
control your iPod
•
If the RI Dock is placed on top of another compo-
nent, the remote controller’s signal may be
obstructed and the remote controller may not
work reliably. In this case, try repositioning the RI
■ To watch an iPod slideshow or video on
TV:
•
Set the OSD mode to Off, and use your iPod’s con-
trols or remote controller to select and start the
slideshow or video.
•
•
•
Make sure your iPod is properly inserted in the RI
Dock.
•
•
•
Make sure that your iPod’s TV OUT setting is set to
On.
Make sure the correct input is selected on your TV
or amp.
When you use the RI Dock’s remote controller,
point it toward the RI Dock (see page 7).
Some of the remote controllers buttons work dif-
ferently depending on the OSD mode: On or Off
Some versions of the iPod do not output video.
■ Your amp unexpectedly selects your iPod
as the input source
■ Your amp’s remote controller doesn’t con-
trol your iPod
•
Always pause iPod playback when listening to
another component that’s connected to your amp.
If playback is not paused, the Direct Change func-
tion may select your iPod as the input source by
mistake when one track ends and another starts
playing.
•
•
3rd generation iPods are not supported.
Make sure your iPod is properly inserted in the RI
Dock. If your iPod is in a case, it may not connect
properly to the RI Dock. Always remove your iPod
from the case before inserting it into the RI Dock.
The iPod cannot be operated while it’s displaying
the Apple logo.
If your amp’s remote controller has remote mode
buttons, make sure you’ve selected the right
mode.
•
•
Caution: If you use this product under
direct sunlight, fluorescent light, or germi-
cidal lamp,ultraviolet or another elements in
the light may change the product exterior
color.
•
•
•
Check the RI Dock’s RI MODE switch setting (see
When you use your amp’s remote controller, point
it toward your amp.
The RI Dock must be connected to your amp with
both an
cable and an audio cable.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply:
Power consumption
(iPod not inserted):
Weight:
AC adapter (5 V DC)
0.5 W
0.51 lbs. (230 g)
Dimensions (W x H x D): 4-7/16 x 2-3/8 x 4-7/16 inches
112 x 60 x 112 mm
Connectors:
VIDEO OUT,AUDIO OUT L/R,
jack
Specifications and features are subject to change
without notice.
In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications
and operation are the same regardless of color.
•
•
The operating instructions in this manual apply
to the iPod as of May 2007,and may change with
future upgrades to the iPod software.
The AC adapter supplied with the DS-A2X is
designed exclusively for use with the DS-A2X.Do
not use it with another device. Likewise, do not
use any other AC adapter with the DS-A2X,
including those supplied with other RI Dock
models. Doing so may damage the RI Dock.
If there’s any noise when listening to an FM or AM
radio station on your tuner or receiver, try mov-
ing its antenna away from the RI Dock, iPod, and
AC adapter’s cable. In addition, don’t wrap the
AC adapter’s cable around any other cables.
•
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
HOMEPAGE
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
Printed in Japan
I0705-1
SN 29344526
(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 5 2 6 *
Download from Www.Somanuals.com. All Manuals Search And Download.
|