Instruction Manual
SV 1716
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
The Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Getting started
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety Precautions
-
This product should only be used with the AC power adapters
included or a type that complies with safety standard EN60065 and that has the following specification:
9 Volt DC / 300mA.
-
-
-
-
-
This product should not be exposed to high temperatures.
This product should not be used in damp places or close to water.
The AC power adapters should only be connected to a power supply of 220-240 VAC / 50Hz.
This product should not be covered.
Inadequately protected or sensitive electronic equipment may be affected by the use of this product.
This interference can lead to damage to either equipment. Before you start, please check whether or not this
product can affect surrounding equipment.
WWW.ONEFORALL.COM
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Product
The Audio Video Sender (SV-1716) is a solution for distributing audio and video signals to every place in the house
without the need of wires. The AV Sender gives you the possibility to view any video source (satellite receiver, video
recorder, camcorder, DVD player, digital or analogue Set-Top Box or Pay-TV decoder box) on your second TV in your
home.
The One For All AV Sender (SV-1716) package contains:
-
-
-
-
-
TRANSMITTER unit
RECEIVER unit
Remote Control Extender Eye
Infra-red (IR) Eye
Two Power adapters
The TRANSMITTER sends the audio and video signals from the source device (VCR, DVD, SATELLITE/ CABLE BOX, CAM-
CORDER, etc) by 2.4 GHz to the RECEIVER that is connected to the destination device. The Remote Control Extender
sends the IR signal in the opposite direction (from RECEIVER unit to TRANSMITTER unit) at a frequency of 433.92 MHz.
TRANSMITTER unit
The TRANSMITTER operates on 9 Volts DC 300mA that is supplied by the AC/DC Adapter (included in package).
The Audio and/or video signals are transformed to a 2.4GHz frequency that will be sent via the built-in antenna.
Furthermore the TRANSMITTER transforms the Remote Control Extender signal (at 433.92 MHz) back to an IR
command.
RECEIVER unit
The RECEIVER operates on 9 Volts DC 300mA that is supplied by the AC/DC Adapter (included in package). The high
frequency signal (2.4GHz) received by this unit are captured by the built-in antenna of the RECEIVER unit and will be
transformed into the original audio and video signals.
Secondly a Remote Control Extender can be controlled too. When an infra red signal is Received by the Remote
Control Extender, it will transform the IR command to 433.92 MHz and can be sent through walls and ceilings.
Please note that this feature is only accessable for devices that are controlled via IR (infra-red) signals at a frequency of
30 - 60 kHz This feature does not support the 2-way IRDA waveform. If you are unsure of the details of the remote
control (IR) output, please refer to the manual of the original device or contact your cable supplier.
4
WWW.ONEFORALL.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 2
Installation
Put both "RECEIVER" and "TRANSMITTER" on the same channel by using the slide switch on the back side of
the units
1
2
Connecting the TRANSMITTER unit
Make sure that the SCART is connected to the correct Output of the device, normally called “Line Out”.
If you wish to remotely control the source device (satellite receiver, video recorder, camcorder, DVD player,
digital or analogue Set-Top Box or Pay-TV decoder box) from another room, for example to change channels
on your satellite receiver, you will need to:
Connect the IR eye to the TRANSMITTER. Place the IR eye directly on the IR receiver window on the front-side
of the source device OR place the IR eye in front of the source device (make sure there is no interference
of the IR Eye signal going to the IR receiver of the source device).
Insert the adapter plug into the connector on the backside.
Now that the unit is connected you can switch ON the Unit using the ON/OFF key.
The red LED on the front should light up.
Connecting the RECEIVER unit
Make sure that the SCART is connected to the correct Input of the device, normally called “Line In”.
3
Insert the adapter plug into the connector on the backside.
If you want to control the source device, place the Remote Control Extender on top or beside the destination device
where it is able to catch the IR command from your remote control.
Now that the unit is connected you can switch ON the Unit using the ON/OFF key.
The red LED on the front should light up.
WWW.ONEFORALL.COM
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
The following paragraphs contain a few examples.
EXAMPLE 1:
Play video on the VCR (source) in the living room and watch
the picture on the TV (destination) in the bedroom.
Connect the TRANSMITTER to the VCR and the RECEIVER to the TV in the bedroom. Switch on the video and insert a
tape. Place the IR eye on / in front of the IR receiver of the VCR. Switch on the TV in the bedroom.
Select the mode on the TV for “Line In” (AV, EXT or channel 0). Aim the VCR remote control to the IR eye and press
play. The video should start playing and picture and sound should appear on your bedroom TV screen.
EXAMPLE 2:
If you do not have coax cable connection with the TV in the bedroom
you can tune in the channels on your VCR (source) in the living room
and watch the picture on the TV (destination) in the bedroom.
You may need the manual of your VCR to tune in the TV channels.
Once all channels are tuned in, you are able to watch your TV channels through your AV channel.
Connect the TRANSMITTER to the VCR and the RECEIVER to the TV in the bedroom. Switch on the video.
Place the IR eye on / in front of the IR receiver of the VCR. Switch on the TV in the bedroom. Select the mode
on the TV for “Line In” (AV, EXT or channel 0). You can take the remote of your VCR to your bedroom to control
your TV channels tuned in your VCR.
EXAMPLE 3:
Also, if you do not have coax cable connection with the TV in the bedroom,
the AV Sender gives the possibility to view your Satellite Receiver (source) programs
also on the TV (destination) in the bedroom.
You probably already tuned in the channels on your Satellite Receiver. If not, you may need the manual of your Satellite
Receiver to tune in the TV channels. Once all channels are tuned in, you are able to watch your TV channels through
your AV channel (or other output channel). Connect the TRANSMITTER to the Satellite Receiver and the RECEIVER
to the TV in the bedroom. Switch on the Satellite Receiver. Place the IR eye on / in front of the IR receiver of the
Satellite Receiver. Switch on the TV in the bedroom. Select the mode on the TV for “Line In” (AV, EXT or channel 0).
You can take the remote of your Satellite Receiver to your bedroom to control your TV channels tuned in your Satellite
Receiver.
6
WWW.ONEFORALL.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Problem & Solution
If your house has a heavy metal construction or is equipped with a PC network, it can disturb the radio
signal. Even moving the units a few inches can improve the performance. If this doesn’t work try to move
the TRANSMITTER and RECEIVER to another place in the house. If you experience problems, try placing the
units away from electrical appliances.
• No picture on second TV.
- Make sure that the TRANSMITTER and RECEIVER are switched ON.
- Make sure that both TRANSMITTER UNIT and RECEIVER UNIT are set to the same channel.
- Select “EXT” or “AV” on second TV.
- Make sure that all cables are connected correctly.
- Make sure that the video source (satellite receiver, video recorder, camcorder, DVD player,
digital or analogue Set-Top Box or Pay-TV decoder box) is switched on.
- Make sure to use the correct SCART connector (e.g. EXT1 or EXT2) of the video source
(check manual of video source).
• Bad picture/ sound quality on second TV.
- Try to find out if the way the cables are placed cause interference.
- Make sure that the distance between the TRANSMITTER and RECEIVER unit is less than 100 ft (30 m).
• Picture of selected TV channel disappears (snow-picture).
- Disable the auto standby mode of the VCR (check the manual of the VCR how to do this).
• The picture on your second TV is not correct.
- Select “EXT” or “AV” on second TV.
- Make sure that the video source is switched on.
• Using a remote control, you cannot control the video source from your second TV.
- Aim the remote control directly at the Remote Control Extender Eye and ensure that there are no obstacles in
between.
- Ensure that there is no other wireless device (wireless headphones, speakers, RF control signals)
interfering with the remote control.
- Make sure that TRANSMITTER and RECEIVER are more than 16 ft (5 m) apart.
- Make sure to use the remote control of the video source.
- Reposition the IR Eye on the video source OR place the IR Eye 2 - 4 inch (5 - 10 cm) in front of the video source.
• Buzzing sound when using the remote control
- With some types of TV you will not be able to solve this problem.
• S-VHS video shows no colour pictures (only black and white).
- Select CVBS video output format for your S-VHS VCR
• DVD player gives no pictures on either main- or second TV.
- Select CVBS video output format for your DVD player (check the DVD player’s user manual.
WWW.ONEFORALL.COM
7
Download from Www.Somanuals.com. All Manuals Search And Download.
0678
Declaration of Conformity
We, Universal Electronics Inc., 6101 Gateway Drive, Cypress, CA 90630, U.S.A., and its subsidiaries
Universal Electronics BV, Institutenweg 21, 7521 PH Enschede, Netherlands,
ONE FOR ALL GmbH, Fabrikstra_e 3, 48599 Gronau, Germany,
ONE FOR ALL UK Ltd, Institutenweg 21, 7521 PH Enschede, Netherlands,
ONE FOR ALL FRANCE S.A.S., Rue Paul Séramy 17, 77300 Fontainebleau, France,
ONE FOR ALL IBERIA S.L., Ctra. Hospitalet, 147-149, 08940 Cornellá de Llobregat, Barcelona, España,
ONE FOR ALL ARGENTINA S.R.L., AV. Las Heras 2126, 5th Floor (Suite “C”) ZC 1111, Recoleta, Buenos Aires, Argentina
Declare under sole responsibility that the ONE FOR ALL Wireless Audio/Video Sender (SV-1716)
is in conformity with the essential requirements as described in Directive 1999/5/EC and satisfies all the technical
regulations to the product within this directive.
EN 300 440-1 (V1.3.1)
EN 300 440-2 (V1.1.2)
EN 301 489-1 (V1.6.1)
EN 301 489-2 (V1.4.1)
EN 50371 (2002)
IEC 60065 (2002)
Enschede, 02 October 2007
Paul J. Bennett
As Managing Director of Universal Electronics BV
Guarantee English UNIVERSAL ELECTRONICS / ONE FOR ALL warrants to the original purchaser that this product will be free from defects in materials and workmanship under normal and correct use for a period of one (1) year
from the date of original purchase. This product will be repaired or if necessary replaced free of charge if it has been proven to be defective within the one (1) year warranty period. The forwarding costs are on the account of the
owner; the costs of returning the product are on the account of UNIVERSAL ELECTRONICS / ONE FOR ALL. This warranty does not cover damage or failures caused by products or services not supplied by UNIVERSAL ELECTRONICS /
ONE FOR ALL, or which result from not mounting the product according to manual instructions. This also applies when the product has been modified / repaired by others than UNIVERSAL ELECTRONICS / ONE FOR ALL or if a fault is
the result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, improper maintenance, alteration, modifications, fire, water, lightning, natural disasters, wrong use or carelessness. To obtain warranty
service during the warranty period, please notice that we need your original purchase receipt so that we may establish your eligibility for service. If you have bought this product for purposes which are not related to your trade,
business or profession, please remind that you may have legal rights under your national legislation governing the sale of consumer goods. This guarantee does not affect those rights.
Universal Electronics BV
Europe & International
P.O. Box 3332
7500 DH, Enschede
The Netherlands
SV 1716
706682
RDN 1051107
Download from Www.Somanuals.com. All Manuals Search And Download.
|