Omron Stereo Amplifier V600 HA User Manual

IVnte6llig0ent0Fl-agHI/IIA  
Innovative RFID Electronic Flags to  
Replace Mechanical Flag and Kanban  
Systems  
• Doesn't need a program and can be used like a sensor.  
• Advanced line construction at minimal cost.  
• Saves space.  
• Precise installation not required (Transmission distance:  
100 mm max.).  
• A verification function provided on multi-functional type.  
• Addition of 16-bit models to the series responds to applica-  
tions from Kanban to quality control.  
• Equipped with a wiring reduction mode and communications  
parity check function (16-bit models).  
• Both NPN and PNP output available.  
• FCC certified.  
Ordering Information/Specifications  
Amplifier  
Type  
Read-only (8-bit)  
V600-HAR91 V600-HAR81  
24 VDC 10%, ripple (p-p): 10%  
Multi-functional (8-bit)  
V600-HAM91 V600-HAM81  
Read-only (16-bit)  
V600-HAR92  
Item  
Model  
Power supply  
Current consumption 130 mA max.  
Transistor output  
Input  
Transistor output or contact output  
Short-circuit current: 3 mA (typical) (IN terminal and 0-V short-circuit)  
OFF voltage:  
15 to 30 VDC  
Input impedance:  
8.2 k  
OFF voltage:  
ON voltage:  
Input impedance:  
Applied voltage:  
15 to 30 VDC  
0 to 5 VDC  
8.2 k  
Short-circuit current:  
3 mA (typical) (for 0-V short-circuit of  
INHIBIT/TRG)  
30 VDC max.  
ON voltage:  
0 to 5 VDC  
Applied voltage:  
30 VDC max.  
NPN open collector  
PNP open collector NPN open collector  
PNP open collector out- NPN open collector output, 20 mA  
Output  
output, 20 mA max. at output, 20 mA max. output, 20 mA max. at put, 20 mA max. at 30  
max. at 30 VDC, residual voltage: 2 V  
30 VDC, residual volt- at 30 VDC, residual 30 VDC, residual volt- VDC, residual voltage: 2 V max.  
age: 2 V max. voltage: 2 V max. age: 2 V max. max.  
Diagnostic functions Checks for CPU errors and transmission errors  
Insulation resistance 50 Mmax. (at 500 VDC) between cable terminals and case  
Dielectric strength  
500 VAC, 50/60 Hz for 1 min between cable terminals and case (leakage current: 1 mA max.)  
2
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sensor  
Model  
Shape  
V600-HS51  
V600-HS61  
V600-HS63  
V600-HS67  
Item  
Transmission frequency 530 kHz  
Ambient temperature  
Storage temperature  
Ambient humidity  
10 to 60°C  
25 to 75°C  
35% to 95%  
50 M(at 500 VDC) between cable terminal and case  
10 to 70°C  
Insulation resistance  
Dielectric strength  
Degree of protection  
Vibration resistance  
1,000 VAC, 50/60 Hz for 1 min between cable terminal and case (leakage current: 1 mA max.)  
IEC60529: IP67  
Destruction: 10 to 2,000 Hz, 3-mm double amplitude, with Destruction: 10 to 500 Hz, 2-mm double amplitude, with 3  
2 sweeps of 15 min each in 3 directions  
sweeps of 11 min each in 3 directions  
Destruction: 981 m/s2, 3 times each in 3 directions (18  
times total)  
Destruction: 490 m/s2, 3 times each in 3 directions (18  
times total)  
Shock resistance  
Cable length  
2 m (fixed)  
Wireless transmission  
error direction  
16-bit CRC (Cyclic Redundancy Check) in both directions  
Indicator  
Weight  
---  
Power: green  
Approx. 70 g  
Approx. 190 g  
Approx. 540 g  
Transmission Distance Specifications  
Recommended Combinations  
Amplifier  
Sensor  
V600-HAR91/-HAR81/-HAM91/-HAM81/-HAR92  
V600-HS61 V600-HS63  
0.5 to 3.0 mm  
Data Carrier  
V600-HS51  
0.5 to 3.0 mm  
V600-HS67  
Memory  
EEPROM  
(Battery-  
less type)  
V600-D23P53  
---  
---  
---  
V600-D23P54  
V600-D23P55  
V600-D23P61  
V600-D23P66N  
0.5 to 5.0 mm  
0.5 to 7.0 mm  
0.5 to 8.0 mm  
---  
0.5 to 5.5 mm  
---  
0.5 to 7.0 mm  
0.5 to 9.5 mm  
2 to 16 mm  
5 to 30 mm  
5 to 25 mm  
5 to 35 mm  
5 to 35 mm  
5 to 45 mm  
10 to 30 mm  
10 to 65 mm  
2 to 15 mm  
---  
0.5 to 9.0 mm  
---  
---  
5 to 35 mm  
5 to 30 mm  
10 to 70 mm  
10 to 50 mm  
10 to 60 mm  
10 to 40 mm  
10 to 100 mm  
---  
V600-D23P66SP ---  
---  
V600-D23P71  
V600-D23P72  
V600-D8KR12  
V600-D8KR13  
V600-D8KR04  
V600-D2KR16  
---  
---  
---  
0.5 to 18 mm  
Memory  
SRAM  
(Built-in-  
battery  
type)  
5 to 15 mm  
5 to 18 mm  
---  
---  
---  
---  
---  
---  
Note: 1. The specifications take fluctuations in ambient temperature and slight differences between products into account.  
2. The read distance and write distance are the same.  
3. Sensor Installation Conditions  
V600-HS51:When flush-mounted in iron  
Axial offset from the Data Carrier: 2.0 mm  
V600-HS61: When surface-mounted on metal (ferrous)  
Axial offset from the Data Carrier: 2.0 mm  
V600-HS63: When surface-mounted on metal (ferrous)  
Axial offset from the Data Carrier: 10.0 mm  
V600-HS67: When surface-mounted on metal (ferrous)  
Axial offset from the Data Carrier: 10.0 mm  
4. Data Carrier Installation Conditions  
V600-D23P53/-P54: When flush-mounted in iron  
V600-D23P55/-P66N/-P66SP/-P71/-P72: When surface-mounted on resin (no metal on the backside)  
V600-D23P61: When surface-mounted on metal (ferrous)  
V600-D8KR12/-13/-04: When surface-mounted on metal (ferrous)  
V600-D2KR16: When the Data Carrier attached to the holder is mounted on a metal (ferrous) surface  
5. The transmission distance specified in the specifications is also applicable when the Data Carrier is mounted on non-metallic surfaces.  
6. The Data Carrier is stationary.  
4
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
Host  
Sensor  
(Cable length: fixed to 2 m)  
Programmable Controller, I/O terminal, B7A, CompoBus/S, etc.  
Sensor Controller  
Terminal block wiring  
Connector  
connection  
Interface cable  
V600-A6R  
V600-A6M  
Amplifier (Cable length:  
fixed to 0.5 m, with connector)  
interface  
Connector pins: 20  
Cable lengths: 2 m, 5 m,  
10 m  
Connector pins: 26  
Cable lengths: 2 m, 5 m,  
10 m  
Connector  
connection  
Connector  
connection  
Connector  
connection  
Amplifier  
Power  
supply  
24 VDC  
V600  
-HAR91/  
HAR81  
Power  
supply  
24 VDC  
V600  
-HAM91/  
HAM81  
Power  
supply  
24 VDC  
V600  
-HAR92  
Connector  
connection  
Connector connection  
V600-HS61  
Connector connection  
Sensor  
V600-HS51  
V600-HS63  
V600-HS67  
Interface cable available in  
three lengths: 2 m,  
5 m, and 10 m (10 m max.)  
Wireless  
transmission  
Wireless  
transmission  
Data Carrier  
V600  
V600  
V600  
V600  
V600  
V600  
V600  
V600  
V600  
V600  
V600  
-D23P53  
-D23P54 -D23P55 -D23P61 -D23P66N -D23P66SP -D23P71  
-D23P72 -D8KR12 -D8KR04 -D2KR16  
Intelligent Flag I/II V600-HA  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Characteristic Data (Typical)  
Transmission Range  
Combinations with the V600-HS51 Sensor  
V600-HS51 & V600-D23P53  
V600-HS51 & V600-D23P54  
V600-HS51 & V600-D23P55  
Y
Y
Y
Y
Y
Y
15  
X
12  
X
X
8
4
10  
5
8
4
–15  
–10  
–5  
0
5
10  
15  
X
–8  
–4  
0
4
8
X
–12  
–8  
–4  
0
4
8
12  
X
V600-HS51 & V600-D23P61  
V600-HS51 & V600-D23P66N  
V600-HS51 & V600-D8KR12  
Y
Y
Y
Y
Y
Y
30  
15  
30  
X
X
X
20  
10  
10  
5
20  
10  
–15  
–10  
–5  
0
5
10  
15  
X
–30  
–20  
–10  
0
10  
20  
30  
X
–30  
–20  
–10  
0
10  
20  
30  
X
Combinations with the V600-HS61 Sensor  
V600-HS61 & V600-D23P53  
V600-HS61 & V600-D23P54  
V600-HS61 & V600-D23P55  
Y
Y
Y
Y
Y
Y
15  
12  
8
X
8
4
X
X
10  
5
4
–12  
–8  
–4  
0
4
8
12  
X
–8  
–4  
0
4
8
X
–15  
–10  
–5  
0
5
10  
15  
X
V600-HS61 & V600-D23P61  
V600-HS61 & V600-D23P72  
V600-HS61 & V600-D8KR12  
Y
Y
Y
Y
Y
Y
30  
30  
20  
15  
10  
5
X
X
X
20  
10  
20  
10  
–30  
–20  
–10  
0
10  
20  
30  
X
X
–25 –20 –15 –10 –5  
0
5
10 15 20 25  
X
–30  
–20  
–10  
0
10  
20  
30  
6
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Combinations with the V600-HS63 Sensor  
V600-HS63 & V600-D23P55  
V600-HS63 & V600-D23P61  
V600-HS63 & V600-D23P66N  
Y
50  
Y
Y
Y
Y
Y
30  
40  
30  
20  
10  
30  
X
X
X
20  
10  
20  
10  
–50 –40 –30 –20 –10  
0
10  
20  
30  
40  
50 X  
–40  
–30  
–20  
–10  
0
10  
20  
30  
40 X  
–30  
–20  
–10  
0
10  
20  
30  
X
V600-HS63 & V600-D23P66SP  
V600-HS63 & V600-D23P71  
V600-HS63 & V600-D23P72  
Y
Y
Y
Y
Y
Y
50  
40  
30  
20  
10  
60  
60  
X
X
X
40  
20  
40  
20  
–60  
–40  
–20  
0
20  
40  
60  
X
–50 –40 –30 –20 –10  
0
10 20 30 40 50 X  
–60  
–40  
–20  
0
20  
40  
60  
X
V600-HS63 & V600-D8KR12  
V600-HS63 & V600-D8KR04  
V600-HS63 & V600-D2KR16  
Y
Y
Y
Y
Y
Y
80  
60  
40  
20  
60  
60  
X
X
X
40  
20  
40  
20  
–60  
–40  
–20  
0
20  
40  
60  
X
–80 –60 –40 –20  
0
20 40 60 80  
X
–80  
–60  
–40 –20  
0
20  
40  
60  
80X  
Intelligent Flag I/II V600-HA  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Combinations with the V600-HS67 Sensor  
V600-HS67 & V600-D23P66N  
V600-HS67 & V600-D23P66SP  
V600-HS67 & V600-D23P71  
Y
Y
Y
Y
Y
Y
80  
80  
100  
80  
60  
40  
20  
60  
40  
20  
60  
40  
X
X
X
20  
80 60 40 20  
0
20  
40  
60  
80 X  
–80 –60 –40 –20  
0
20  
40  
60  
80 X  
–100 –80 –60 –40 –20  
0
20 40 60 80 100 X  
V600-HS67 & V600-D23P72  
V600-HS67 & V600-D8KR12  
V600-HS67 & V600-D8KR13  
Y
Y
Y
Y
Y
Y
80  
80  
100  
X
80  
60  
40  
20  
X
60  
40  
20  
60  
40  
20  
X
–80 –60 –40 –20  
0
20  
40  
60  
80 X  
–80 –60 –40 –20  
0
20  
40  
60  
80 X  
–100 –80 –60 –40 –20  
0
20 40 60 80 100X  
V600-HS67 & V600-D8KR04  
Y
Y
120  
X
80  
40  
–120  
–80  
–40  
0
40  
80  
120 X  
Transmission Time  
The transmission time refers to the time required for communications between the Sensor and the Data Carrier. It is used for calculating the travel  
speed of the auto command.  
DC speed  
(conveyor  
speed)  
Distance travelled in the transmission range  
Transmission time  
=
Model  
Read  
V600-HAR91/-HAR81/-HAM91/-HAM81  
Write  
V600-HAR92  
Read  
Mode type DATA READ mode,  
VERIFY READ mode  
BYTE mode  
BIT SET mode, BIT  
CLEAR mode  
DATA READ mode  
Data Carrier type  
EEPROM  
SRAM  
75 ms  
60 ms  
138 ms  
95 ms  
150 ms  
107 ms  
77 ms  
62 ms  
Example: Combinations with the V600-HAR91, V600-HS63, and V600-D8KR04 Sensors.  
Note: 1. The DC speed varies depending on transmission distance Y  
and the axial offset. It is recommended that you refer to the  
transmission range graphs and use the product where the  
range is the largest.  
Y
Y
80  
60  
40  
20  
X
2. This calculation is intended as a guideline only. Perform a  
test with the actual product prior to use.  
3. This equation does not include transmission error process-  
ing.  
–80 –60 –40 –20  
0
20 40 60 80  
X
75 × 10-3 (m)  
60 × 10-3 × 1/60 (min)  
DC speed  
(conveyor  
speed)  
75 (mm)  
60 (ms)  
=
=
= 75 (m/min)  
8
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Circuit Configuration  
V600-HAR91  
V600-HAM91  
V600-HAR81  
V600-HAM81  
Input Circuit  
Input Circuit  
+DC  
24 V  
Tr  
IN  
8.2 k  
ON/  
OFF  
Main circuit  
IN  
Main circuit  
8.2 kΩ  
Tr  
0 V  
0 V  
Output Circuit  
Output Circuit  
+DC  
OUT  
OUT  
0 V  
Main circuit  
Main circuit  
0 V  
V600-HAR92  
Input Circuit  
24 V  
8.2 kΩ  
ON/  
OFF  
Main circuit  
IN  
Tr  
0 V  
Output Circuit  
OUT  
0 V  
Main circuit  
Precautions  
The following OMRON products cannot be connected to this product.  
Cautions  
CVM1-OD219, C20H, C28H, C40H, or C60H Programmable  
Controllers  
!Caution  
Sensor Controllers other than from the S3D2 Series  
Be sure to house the V600-HA@91/-HA@81/-HA@92 together with  
their connectors and cable in control boxes when using them and  
do not expose them to water, oil, dust, metal powder, corrosive  
gas, or organic solvent, otherwise they may malfunction, suffer  
damage, or burn.  
When using a contact output, pay careful attention to chattering and  
to the minimum switching current. Also note that the minimum switch-  
ing current may be specified for some solid-state outputs.  
When connecting an inductive load or an electrical device that tends  
to generate noise to the output, connect a diode in parallel with the  
load. Connect the cathode side of the diode to the positive side of the  
power source.  
!Caution  
The connectors of the V600-HA@91/-HA@81/-HA@92 can be  
mounted to metal plates, provided that there is an insulation plate  
with a thickness of 1.5 mm minimum between each of the connec-  
tors and metal plates.  
L
DC  
Open collector output  
Diode  
power supply  
Input/Output  
The Data Input and Data Output lines are set to “1" when the transis-  
tor turns ON and to “0" when it turns OFF.  
Do not use a solid-state output with the following ratings with the  
V600-HAM91/-HAM81, otherwise an external input error may result.  
Diode  
Peak inverse voltage  
Minimum of three times of the load voltage  
Average rectified current: 1 A  
1. Maximum switching current: 1 A min.  
2. Minimum switching current: 10 mA min.  
3. Response time (ON to OFF): 3 ms min.  
Intelligent Flag I/II V600-HA  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power Supply Voltage  
I/O Interface Requirements  
Do not impose any voltage exceeding the rated voltage range. Doing  
so, or applying alternating current (100 VAC) may cause the product  
to explode or burn.  
1. The TRG input must be 10 ms min.  
2. The INHIBIT input must be 20 ms min.  
3. Minimum of 5 ms is required as the transfer time of the Read/  
Write Selection Input (W/R).  
Load Short-circuiting  
Do not short-circuit the load connected to the product or connect to  
the power supply. Doing so may cause the product to explode or  
burn.  
4. The read data output must be read after the Normal End Output is  
set to ON.  
Connecting the Sensor  
Hold the black part of the connector, line up the notch and push it in  
until it clicks.  
Wiring  
Avoid wiring mistakes such as incorrect polarity in the power supply.  
Wiring mistakes may cause the product to explode or burn.  
Correct Use  
Grounding  
The FG line is provided for grounding to the earth. When using the  
Amplifier in an environment where it is exposed to large amounts of  
noise or if the V600-HA@91/-HA@81/-HA@92 Amplifier malfunctions,  
provide a Class-3 ground (ground resistance of 100 or less). Note  
that sharing the grounding wire with other equipment or grounding to  
the beam of a building will adversely affect the grounding effect.  
V600-HA91/81/92  
Other equipment  
Compatibility with the SRAM Memory  
Type Data Carrier  
1. If the Data Carrier is stationary in the transmission area for a long  
time when using the V600-HA@91/81 in the AUTO mode, or when  
using the V600-HAR92, it will drastically reduce the battery life.  
Therefore, stop the oscillation in the sensor either by turning off  
the power of the V600-HA@91/81/92 Amplifier or by setting the  
Inhibit input to ON.  
OK  
FG  
Less than 100 Ω  
V600-HA91/81/92  
Other equipment  
2. Use a Data Carrier that has the oscillation frequency of 530 kHz.  
Note that the following models manufactured before February  
1991 cannot be used.  
NG  
FG  
V600-D2KR01  
V600-D2KR02  
Less than 100 Ω  
Precautions When Using the AUTO  
Mode  
Mounting  
Amplifier Spacing  
If transmitting to the Data Carrier while it is traveling under the AUTO  
mode, conduct tests to make sure that the travel speed and installa-  
tion conditions are fully satisfied.  
When installing V600-HA@91/V600-HA@81/V600-HA@92 Amplifi-  
ers in a row, provide a minimum space of 10 mm between Amplifiers  
in order to prevent them from being affected by the heat produced by  
each Amplifier.  
10 mm min.  
V600-HA91/81/92  
When housing the Amplifiers in a box, provide a fan or ventilation  
opening for radiating the heat.  
When wiring power cables, which carry large current such as motor  
drive cables, near the V600-HA@91/81/92 Amplifiers, conduct neces-  
sary tests to make sure that the installation conditions are fully satis-  
fied.  
10  
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Note: All units are in millimeters unless otherwise indicated.  
Amplifier  
V600-HAR91/-HAR81  
25  
* Enlarged Section of Mounting Hole  
4.4  
30  
Mounting Hole Dimensions  
5.5  
30  
21  
55  
Two, mounting  
holes  
30û  
6
*
2-M4  
17.5  
28.3  
36.3  
61.8  
68.5  
89 0.2  
80  
35.2  
89  
98  
21 0.2  
Vinyl-insulated round cord 5.8-mm dia.,  
13-conductor cable, standard length: 0.5 m  
500 mm  
28.1  
XG4E-2031  
44.7  
8.2  
25  
Intelligent Flag I/II V600-HA  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V600-HAM91/-HAM81  
25  
* Enlarged Section of Mounting Hole  
4.4  
30  
Mounting Hole Dimensions  
5.5  
30  
21  
55  
Two mounting  
holes *  
30˚  
6
2-M4  
17.5  
28.3  
36.3  
44.3  
52.3  
61.8  
68.5  
89 0.2  
75  
80  
35.2  
89  
98  
21 0.2  
Vinyl-insulated round cord 5.8-mm dia.,  
23-conductor cable, standard length: 0.5 m  
500 mm  
28.1  
XG4E-2631  
52.3  
8.2  
25  
12  
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V600-HAR92  
25  
* Enlarged Section of Mounting Hole  
4.4  
30  
Mounting Hole Dimensions  
5.5  
30  
21  
55  
Two, mounting  
holes *  
30˚  
6
2-M4  
17.5  
28.3  
36.3  
44.3  
61.8  
68.5  
89 0.2  
75  
80  
35.2  
89  
98  
21 0.2  
Vinyl-insulated round cord 5.8-mm dia.,  
23-conductor cable, standard length: 0.5 m  
500 mm  
28.1  
XG4E-2631  
52.3  
8.2  
25  
Sensor  
V600-HS51  
2 lock washers  
2 lock nuts  
Vinyl-insulated round cord (4-mm dia.)  
Connector  
M12X1  
Case: Brass  
Transmission window: ABS resin  
Filter: Epoxy resin  
13.7 dia.  
9.6 dia.  
Cable: PVC (oil-resistant)  
7
49.5  
33  
35  
V600-HS61  
30.5  
18  
4.5  
8.5  
12 0.2  
49.5  
Case: ABS resin  
Filter: Epoxy resin  
18  
13.7 dia.  
Cable: PVC (oil-resistant)  
Connector  
Vinyl-insulated round cord (4-mm dia.)  
Detection surface  
2-3.5X5  
(mounting holes)  
10  
6.5  
Intelligent Flag I/II V600-HA  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V600-HS63  
Two, 4.5-dia. mounting holes  
Vinyl-insulated round cord 6-mm dia  
2-R5  
4-R1  
Connector  
(7/0.18-mm dia.), 8-conductor cable,  
standard length: 2 m  
Bushing  
10  
40  
28  
13.8 dia.  
51.5  
5
5
13  
18  
27  
6
5
53  
20  
Power indicator (green)  
23  
11  
Case: ABS resin  
Filter: Epoxy resin  
Cable: PVC (oil-resistant)  
V600-HS67  
Four, 4.5-dia.  
mounting holes  
100  
0.2  
90  
5
5
50  
50  
Connector  
Power indicator  
(green)  
25  
100  
13.8 dia.  
0.2  
90  
51.5  
Bushing  
Vinyl-insulated round cord (6-mm dia.)  
10  
Case: ABS resin  
Filter: Epoxy resin  
Cable: PVC (oil-resistant)  
14  
10  
30  
20  
11  
Interface Cable  
V600-A6@R (for V600-HAR91/-HAR81))  
10.6  
+5  
+100  
7.6  
330  
L
30  
0
0
5
5
5
5
20  
20  
20  
30  
37.6  
Vinyl-insulated round cord 9-mm dia  
(7/0.2-mm dia.), 13-conductor cable,  
standard length: 2 m  
XG5M-2032-N Connector  
14  
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V600-A6@M (for V600-HAM91/-HAM81/-HAR92)  
10.6  
+5  
+100  
7.6  
330  
L
30  
0
0
5
5
5
5
20  
20  
20  
30  
37.6  
Vinyl-insulated round cord 9-mm dia (7/0.2-mm dia.),  
23-conductor cable, standard length: 2 m  
XG5M-2632-N Connector  
Model  
L (m)  
V600-A60R/60M  
V600-A61R/61M  
V600-A62R/62M  
2
5
10  
Intelligent Flag I/II V600-HA  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Terms and Conditions  
of all possible uses of this product, nor is it intended to imply that the  
uses listed may be suitable for this product:  
WARRANTY, LIMITATIONS OF  
LIABILITY  
WARRANTY OMRON’s exclusive warranty is that the products are  
free from defects in materials and workmanship for a period of one  
year (or other period if specified) from date of sale by OMRON.  
• Outdoor use, uses involving potential chemical contamination or  
electrical interference, or conditions or uses not described in this  
catalog.  
• Nuclear energy control systems, combustion systems, railroad sys-  
tems, aviation systems, medical equipment, amusement machines,  
vehicles, safety equipment, and installations subject to separate  
industry or government regulations.  
OMRON MAKES NO WARRANTY OR REPRESENTATION,  
EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,  
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE  
OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES  
THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL  
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED  
USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS  
OR IMPLIED.  
• Systems, machines and equipment that could present a risk to life  
or property.  
Please know and observe all prohibitions of use applicable to this  
product.  
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING  
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING  
THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO  
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS  
PROPERLY RATED AND INSTALLED FOR THE INTENDED USE  
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.  
LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSI-  
BLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES,  
LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CON-  
NECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS  
BASED ON CONTRACT, WARRANTY, NEGLIGENCE OR STRICT  
LIABILITY.  
PROGRAMMABLE PRODUCTS OMRON shall not be responsible  
for the user’s programming of a programmable product, or any con-  
sequence thereof.  
In no event shall responsibility of OMRON for any act exceed the indi-  
vidual price of the product on which liability is asserted.  
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WAR-  
RANTY, REPAIR OR OTHER CLAIMS REGARDING THE PROD-  
UCTS UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE  
PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED  
AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION,  
ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR  
REPAIR.  
DISCLAIMERS  
PERFORMANCE DATA Performance data given in this catalog is  
provided as a guide for the user in determining suitability and does  
not constitute a warranty. It may represent the result of OMRON’s  
test conditions, and the user must correlate it to actual application  
requirements. Actual performance is subject to the OMRON War-  
ranty and Limitations of Liability.  
APPLICATION CONSIDERATIONS  
SUITABILITY FOR USE OMRON shall not be responsible for confor-  
mity with any standards, codes or regulations which apply to the  
combination of the product in the customer's application or use of the  
product.  
CHANGE IN SPECIFICATIONS Product specifications and accesso-  
ries may be changed at any time based on improvements and other  
reasons. It is our practice to change part numbers when published  
ratings or features are changed, or when significant construction  
changes are made. However, some specifications of the product may  
be changed without any notice. When in doubt, special part numbers  
may be assigned to fix or establish key specifications for your appli-  
cation. Please consult with your OMRON representative at any time  
to confirm actual specifications of purchased product.  
At the customer's request, OMRON will provide applicable third party  
certification documents identifying ratings and limitations of use  
which apply to the product. This information by itself is not sufficient  
for a complete determination of the suitability of the product in combi-  
nation with the end product, machine, system, or other application or  
use.  
ERRORS AND OMISSIONS The information in this catalog has  
been carefully checked and is believed to be accurate; however, no  
responsibility is assumed for clerical, typographical or proofreading  
errors, or omissions.  
The following are some examples of applications for which particular  
attention must be given. This is not intended to be an exhaustive list  
Complete terms and conditions for product purchase and use are on Omron’s website at  
www.omron.com/oei under the “About Us” tab, in the Legal Matters section.  
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, divide by 25.4  
OMRON ON-LINE  
OMRON ELECTRONICS LLC  
One Commerce Drive  
Schaumburg, IL 60173  
OMRON CANADA, INC.  
885 Milner Avenue  
Toronto, Ontario M1B 5V8  
847-843-7900  
416-286-6465  
For US technical support or other inquiries:  
800-556-6766  
5/03  
Specifications subject to change without notice  
Printed in USA  
Cat. No. GC RFID 4  
16  
Intelligent Flag I/II V600-HA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Moxa Technologies Computer Hardware W311 User Manual
Murphy Switch PSB User Manual
NordicTrack Treadmill NTTL18990 User Manual
Olympus Camera Lens VT521901 User Manual
Onkyo Stereo System TX SR573 User Manual
Oregon Scientific Clock RAR186 User Manual
Palsonic DVD Player PVP 150 User Manual
Paradyne Network Router Hotwire 7984 User Manual
Paradyne Network Router Routers User Manual
Patton electronic Network Card 2173R User Manual