Lift 42
Motorized Flat Panel Lift System with
Universal Adapter.
ULN # 10235
PN # Lift 42 = L1-10235-PRO-101008vE
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMAGES MAY DIFFER FROM ACTUAL PRODUCT.
Contents
Contents
1
2
3
4
5
6
7
8
9
1 Base Mount
1 Lift Column
1 Bayonet Bracket
1 Screen Support
1 Top Plate
1
1 Control Box
1 Remote Control
1 IR Receiver/Control switch
2 Corner brackets
2
10 1 Universal Adapter
11 2 Vertical Extension Rails and covers
12 1 Screen Adapter
13 1 Motor cable
14 1 Power cable
5
3
4
6
7
9
8
10
11
12
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Contents
Monitor Kit: Parts M-A through M-N are used to connect the TV to the universal
adapter. Spacers may be necessary for a proper fit with recessed mounting holes or to
allow access to TV inputs.
Monitor Kit L-U-vA
Pouch # Part # Qty
Description
M-A
M-B
M-C
M-A
M-B
M-A
M-B
M-C
M-D
M-E
M-F
M-G
M-H
M-I
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Philips screws M4 x 15mm
Philips screws M4 x 35mm
Philips screws M4 x 50mm
Philips screws M5 x 15mm
Philips screws M5 x 35mm
Philips screws M5 x 50mm
Philips screws M6 x 15mm
Philips screws M6 x 35mm
Philips screws M6 x 50mm
Philips screws M8 x 15mm
Philips screws M8 x 35mm
Philips screws M8 x 50mm
5/8" spacer
M-C
M-D
M-E
M-F
M-G
M-H
M-I
M-D
M-E
M-J
M-K
M-L
M-M
M-N
10235vB
M-J
M-K
M-L
M-M
M-N
3/4" spacer
M-F
O
P
Q
R
S
T
U
V
W
X
Y
4
4
4
4
4
2
4
4
4
1
1
Hex screws M6 x 20mm
Hex screws M6 x 30mm
Philips screws #10 x 3/4"
Philips screws #8 x 3/4"
Hex screws 3/8-16 x 3/4"
2" x 1/4" Steel guide pins
Square washers
Felt corner cushions
Hex screws 1/4-20 x 1/2"
Allen wrench 7/32”
M-G
M-H
Allen wrench 5/32”
M-I
P
T
M-J
M-K
V
X
M-L
U
Y
S
M-M
M-N
W
O
Q
R
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Before Installation
ƒ Prior to enclosure construction and lift assembly,
please read through the below warnings and
recommendations to ensure a successful
installation!
ƒ PINCH POINT WARNING!
• Improper construction of lift enclosure can create dangerous pinch points. It is
the responsibility of the installer to ensure the intended use of this product does
not create hazardous pinch zones. Installation design should prevent users from
inserting objects between moving parts and fixed objects! Failure to do so may
result in serious injury or property damage.
ƒ LIFT STABILITY:
• The Lift System should be installed into material at least ¾” thick on both the
back and bottom surfaces. The Lift Column is ONLY authorized and tested in a
vertical, upright orientation. For enclosures not secured structurally, be sure that
enclosure does not create a tip hazard when the lift is in the open position. DO
NOT MOUNT THE LIFT SYSTEM UPSIDE DOWN (AS IN A CEILING MOUNT),
OR SIDEWAYS (AS IN A LATERAL MOUNT)!
ƒ ENCLOSURE DIMESIONS:
• Before constructing the enclosure carefully consider the dimensions of the TV to
be used and the lift mechanism. If possible “dry fit” (see next page) the TV to the
lift mechanism prior to building the enclosure to ensure proper fit and function.
ƒ LARGE TV’S:
• With larger televisions the lift unit or lid may need extended to properly fit into
the enclosure. The most common application will be to use a spacer block (not
included) and corner brackets (part #12) to elevate the lift mechanism to allow
for greater TV height.
ƒ FLOATING TOP:
• With floating top installations, it is important to center the lift within the enclosure
and center the cabinet top on the lift. With included hardware, the cabinet lid is
NOT designated as a weight bearing surface. For safety reasons the cabinet top
should be constructed in a “floating” configuration using the guide pins provided
to prevent pinch points. See guide pin template in appendix for recommendation.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Before Enclosure Construction!
ƒ Assemble lift mechanism and connect the TV to be used in the
install to determine dimensions for the lift enclosure prior to
construction. Be sure to leave room for adjustments If
necessary. An out of cabinet assembly of the mechanism can
be done using steps 1,4,6,8,9 and 10 in order.
(D)
(D + 2”)
(W + 2”)
(H)
(H + 2”)
Minimum INTERIOR Dimensions
(H) Minimum Height
Height of lift in closed
position or Height of TV + 2”
NOTE: For use with the
longer rails spacers will be
needed above and below the
lift mechanism
(D) Minimum Depth
Depth of TV + Depth of
Mount + 2”
(W) Minimum Width
Be very careful not to build
the enclosure too shallow.
The mount may not function
or damage to the TV could
Width of TV + 2”
This will allow 1 “ of clearance on either
side of the television.
Download from Www.Somanuals.com. All Manuals Search And oDcowcnulroad.
6
Measurements Required For Cabinetry Dimensions
ƒ Use previous page to find the minimum INTERIOR dimensions
for custom enclosures.
Width
Height
Depth
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Step 1
ƒ Attach the Base Bracket (1) to the Lift Column (2):
• Using the small Hex wrench and 6mm x 20mm screws (O), connect the base
bracket to the lift column. Note that one side is counter sunk to ensure flush
installation of screws. Hand tighten all four screws before proceeding. If the
height of the TV to be used is greater than 22” a spacer block will be needed
under the base bracket and lift column.
2
1
O
x4
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Step 2
ƒ Attach the Bayonet Bracket (3) to the enclosure:
• Using the #10 x ¾” screws (Q), attach the bracket so that the top edge of the
brackets back plate is 20” above the bottom mounting surface (the bottom of the
cabinet or top of the spacer block if used).
3
x4
Q
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Step 3
ƒ Secure Lift Column and Base Bracket in enclosure:
• Gently glide the lift column into place on the bayonet bracket so that the tapered
slots on the column are secured to the extrusions on the bracket. Gently push
down until the base bracket is touching the bottom of the enclosure. DO NOT
ATTACH THE BASE BRACKET TO THE MOUNTING SUREFACE AT THIS
TIME!
• For floating top installations it is recommended that the top of the lift column sits
below the lip of the enclosure by 10mm (7/16”) to allow room for the top plate so
that the lid sits flush and the guide pins function properly.
Figure A
2
Figure B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Step 4
ƒ Connect Screen Adapter (12) to the Screen Support (4):
• Use the large hex wrench to secure the screen adapter to the screen support
using four 3/8-16 x ¾” screws (S). Depending on TV size and mounting hole
pattern the screen adapter can be vertically adjusted for optimal fit.
TOP
12
4
12
4
S
x4
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Step 5
ƒ Initialize the lift system:
• Connect the motor cable to the control box and “pigtail” on the lift column as shown in
figures A and B.
• Connect the IR receiver/control switch and control box power as shown in figures C and
D.
• Once all the cables are properly connected, the lift must be initialized by pressing and
holding the down button on the IR receiver until the column is at its lowest limit (see
figure E for IR receiver orientation). There will be slight raising and lowering of the lift.
• Release the down button momentarily before depressing it again for 2 seconds. There
will again be a slight movement of the lift, this means the lift is initialized and all previous
settings erased.
ƒ Set the upper limit
• Press and hold the up button until the desired top limit is reached, release the up button
and depress the down button to stop the lift and set the upper limit. If you want maximum
extension, hold the up key until the lift is fully extended and stops before releasing.
• The settings will now function when the mechanism is opperated by remote control.
ƒ In order to reset the programming, disconnect power to the unit and repeat the
above steps.
Figure A
6
Figure C
Figure D
6
6
Figure E
IR
Download from Www.Somanuals.com. All ManDuaWls NSearch And Download.
UP
12
Step 6
ƒ Attach the Screen Support(4) and Top Plate(5) to the Lift
Column(2):
• Before attaching the top plate ensure that the rubber guide on the “pigtail” is
secured in the square cutout on what will be the front of the lift column (fig. A).
Failure to do so may result in damage to the wire.
• Once the pigtail is secure, line up the holes on top of the screen support with the
holes in the lift column. Make sure the plate is on the same side as the pigtail,
the pigtail will be protected by the screen support (fig. B). Finally line up the
holes on the top plate with the holes on the screen support and secure the
assembly with four 6mm x 30mm screws (P). Note that top plate is also counter
sunk for flush mounting (fig. C).
Before
After
Figure A
Figure C
Figure B
5
x4
5
4
4
2
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Step 7
ƒ Attach lift assembly to enclosure base:
• Using a level on the top plate ensure that the lift column and assembly are
level within the enclosure. Gently tap the base of the column left or right to
bring the top plate level.
• Using four #10 x ¾” (Q) screws attach the base bracket and lift assembly to
the enclosure.
2
1
Q
x4
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Step 8
ƒ Attach the Universal Adapter to the TV:
• Place the TV face down on a protected surface.
• For larger TV’s, the vertical rails may need swapped out for the longer included
rails. Rails are swapped by removing 2 Phillips screws per rail.
• Use the self center function of the adapter to line up the TV’s mounting holes
with the slots in the vertical rails. Connect the TV to the adapter using the
correct screws (M-A – M-L) and square washers (U). Spacers (M-M and M-N)
may be needed if the TV has recessed mounting holes or if inputs are
obstructed by the mount. IF SPACERS ARE REQUIRED, THE INSIDE
DIMENISIONS OF THE ENCLOSURE MUST ACCOMMODATE THIS NEED!
• DO NOT OVERTIGHTEN HARDWARE, DAMAGE TO THE TV MAY RESULT.
10
M-A – M-L
M-A – M-L
11
10
Note: IF MONITOR SCREWS “BOTTOM OUT”, THEN USE ADDITIONAL WASHERS
(not included) TO TAKE UP THE SLACK.
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Step 9
ƒ Connect the TV and universal adapter to the lift column:
• Partially install two ¼-20 x ½” (W) hex screws into the top rear of the universal
adapter (fig. A).
• Lift and lock TV into position on screen adapter (fig. B).
• Install two remaining hex screws through the screen adapter into the universal
adapter. Hand tighten all 4 hex screws to secure TV to the lift column (fig. C).
Figure A
Figure B
Figure C
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Step 10
ƒ Install universal adapter rail covers:
• Carefully attach the correct plastic covers to the universal adapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Appendix
ƒ Using guide pins for a floating top:
• The guide pins are recommended for use as a safety measure to prevent pinch
points. A template has been included to assist with guide pin use.
• If the guide pins are to be used, make sure the top surface of the enclosure will
not be used as a load bearing surface.
• Carefully consider the location of the top plate and guide pins in relation to the
center of the enclosure lid before construction of the enclosure. The top plate
and guide pins should be directly centered to maximize lid stability.
• Improper use of guide pins may result in property damage or injury. If you are
unsure or are having difficulty using the guide pins with a floating top, contact a
professional installer or OmniMount customer service.
Enclosure lid
Guide pins
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Guide Pin/Top Plate Template
Download from Www.Somanuals.com. All Manuals Search And Download.
19
OmniMount Systems, Inc.
8201 South 48th Street
Phoenix, AZ 85044-5355
1-800-MOUNT-IT
1-800-668-6848
Thank you for purchasing an OmniMount product.
Download from Www.Somanuals.com. All Manuals Search And Download.
|