NV-MPS4 Music Port Server
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTENNA
LEAD-IN
WIRE
GROUND
CLAMPS
ANTENNA
DISCHARGE UNIT
NEC SECTION
810-20
GROUNDING
CONDUCTORS
ELECTRIC
SERVICE
ENTRANCE
GROUND CLAMPS
POWER SERVICE
GROUPING ELECTRODE
SYSTEM NEC ART 250
PART H
NEC NATIONAL ELECTRICAL CODE
SAFETY NOTE:
Where the MAINS plug or appliance
coupler is used as the disconnect
device, the disconnect device shall
remain readily operable
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Danger
1. Read all safety and operating instructions before using this
Exposure to extremely high noise levels may cause a permanent
hearing loss. Individuals vary considerably to noise induced hearing
loss but nearly everyone will lose some hearing if exposed to sufficiently
intense noise for a sufficient time. The U.S. Government's
Occupational Safety and Health Administration (OSHA) has specified
the following permissible noise level exposures:
product.
2. All safety and operating instructions should be kept for future
reference.
3. Read and understand all warnings listed on the operating
instructions.
4 . Follow all operating instructions to operate this product.
5. This product should not be used near water, i.e. bathtub, sink,
swimming pool, wet basement, etc.
6. Only use dry cloth to clean this product.
7. Do not block any ventilation openings, It should not be placed flat
DURATION PER DAY (HOURS)
SOUND LEVEL (dB)
8
6
4
3
2
1
against a wall or placed in a built-in enclosure that will impede the
90 93 95 97 100 103
flow of cooling air.
8. Do not install this product near any heat sources ; such as,
radiators, heat registers, stove or other apparatus (including heat
According to OSHA, any exposure in the above permissible limits could
result in some hearing loss. Ear plugs or protectors in the ear canal or over
the ears must be worn when operating this amplification system in order to
prevent a permanent hearing loss. If exposure in excess of the limits as
put forth above, to insure against potentially harmful exposure to high
sound pressure levels, it is recommended that all persons exposed to
equipment capable of inducing high sound pressure levels, such as this
amplification system, be protected by hearing protectors while this unit is in
operation.
producing amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord being walked on or pinched, particularly at
plugs, convenience receptacles and the point where they exit
from the apparatus. Do not break the ground pin of the power
supply cord.
11 . Only use attachments specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
the manufacturer or sold with the apparatus. When a cart is used,
use caution when moving cart/apparatus combination to avoid
injury from tip-over.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE CHASSIS. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Care should be taken so that objects do not fall and liquids are
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF NON-INSULATED "DANGEROUS VOLTAGE" WITHIN THE
PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
not spilled into the unit through the ventilation ports or any other
openings.
15. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way;
such as, power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
or has been dropped.
16. WARNING: To reduce the risk of fire or electric shock, do not
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.
expose this apparatus to rain or moisture.
Download from Www.Somanuals.com. All Manuals Search And Download.
FRENCH
IMPORTANTES INSTRUCTIONS DE SECURITE
1. Lire avec attention toutes les recommandations et précautions
d'emploi avant d'utiliser ce produit.
Danger
2. Toutes les recommandations et précautions d'emploi doivent être
conservées afin de pouvoir s'y reporter si nécessaire.
3. Lire et comprendre tous les avertissements énumérés dans les
précautions d'emploi.
L‘exposition a des niveaux eleves de bruit peut provoquer une perte
permanente de l’audition, Chaque organisme humain reagit
differemment quant a la perte de l’audition, mais quasiment tout le
monde subit une diminution de I’acuite auditive lors d’une exposition
suffisamment longue au bruit intense. Les autorites competentes en
reglementation de bruit ont defini les expositions tolerees aux niveaux
de bruits:
4. Suivre toutes les précautions d'emploi pour utiliser ce produit.
5. Ce produit ne doit pas être utilisé près d'eau, comme par exemple
baignoires, éviers, piscine, sous-sol humides ... Etc.
6. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.
7. Ne bloquér aucune ouverture de ventilation. Ne pas placer le
produit tout contre un mur ou dans une enceinte fernée, cela
gênerait le flux d'air nécessaire au refroidissement.
DURE EN HEURES PAR JOUR
8
6
4
3
2
1
INIVEAU SONORE CONTINU EN dB
90 93 95 97 100 103
8. Ne pas placer le produit près de toute source de chaeur telle que
radiateurs, arrivées d'air chaud, fourneaux ou autres appareils
générant de la chaleur (incluant les amplificateurs producteurs
de chaleur) .
Selon les autorites, toute exposition dans les limites citees ci-dessus,
peuvent provoquer certaines pertes d’audition. Des bouchons ou
protections dans l’appareil auditif ou sur l’oreille doivent etre portes lors
de l’utilisation de ce systeme d’amplification afin de prevenir le risque
de perte permanente de l’audition, Dans le cas d’expositions
superieures aux limites precitees il est recommande, afin de se
premunir contre les expositions aux pressions acoustiquese I evees
potentielIement dangeure u ses, aux personnes exposees aux
equipements capables de delivrer de telles puissances, tels ce
systeme d’amplification en fonctionnement, de proteger l’appareil
auditif.
9. Ne pas négliger la sécurité que procure un branchement polarisé
ou avec raccordement à la terre, Un branchement polarisé
comprend deux fiches dont l'une est plus large que l'autre. Un
branchement à la terre comprend deux fiches plus une troisième
reliée à la terre. Si la fiche secteur fournie ne s'insert pas dans
votre prise de courant. consulter un 'électricien afin de remplacer
votre prise obsolète.
10. Protéger le cordon d'alimentation de tout écrasement ou
pincement, particulièrement au niveau des fiches, des
réceptacles utilisés et à l'endroit de sortie de l'appareil. Ne pas
casser la fiche de terre du cordon d'alimentation.
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR.
11. Utiliser uniquement les accessoires spécifiés par le constructeur.
12. Utiliser uniquement avec le chariot de transport, le support, le
trépied, la console ou la table spécifiés par le constructeur ou
vendus avec l'appareil. Lors de l'utilisation d'un chariot, bouger
avec précaution l'ensemble chariotlappareil afin d'éviter les
dommages d'un renversement.
ATTENTION: AFIN DE LlMlTER LE RISQUE DE CHO ELECTR/QUE, NE
PAS ENLEVER LE CHASSIS. NE CONTIENT PAS DE
PIECES POUVANT ETRE REPAREE PAR L’UTILISATEUR.
CONFER LE SERVICE APRES-VENTE AUX
REPARATEURS
13 Débrancher cet appareil lors d'orages ou s'il n'est pas utilisé
pendant une longue période.
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE
DE VOLTAGE DANGEREUX NON-ISOLE A L'INTERIEUR DE CE PRODUIT
QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT IMPORTANTE POUR
PROVOQUER UN CHOC ELECTRIQUE AUX PERSONNES.
14. Des précautions doivent être prises afin qu'aucun objet ne tombe
et qu'aucun liquide ne se répande à l'intérieur de l'appareil par
les orifics de ventilation ou n'importe quelle autre ouverture.
15. Pour toutes interventions techniques s'adresser à un technicien
qualifié.L'intervention technique est nécessaire lorsque l'appareil
a été endommagé de n'importe quelle façon, comme par
exemple si le cordon secteur ou sa fiche sont détériorés,si du
liquide a coulé ou si des objets sont tombés à l'intérieur de
l'apparei1,si l'appareil a été exposé à la pluie ou à l'humidité, s'il
ne fonctionne pas normalement ou s'il est tombé.
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE
D'INSTRUCTIONS D'UTILISATION ET DE MAINTENANCE DANS LES
DOCUMENTS FOURNIS AVEC CE PRODUIT.
AFIN DE REDUIRE LES RISQUÉ D'INCENDIE ET DE DECHARGE
ELECTRIQUE, NE PAS EXPOSER CET APPAREILA LA PLUIE OU A
L'HUMIDITE.
16. ATTENTI0N:Pour réduire le risque d'incendie ou de choc
electrique ne pas exposer l'appareil à la pluie ou à l'humidité.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Music Port Server Front Panel Features
Music Port Server Back Panel Features
Page 3
Page 4
Page 5
I. Installing the NV-NV-MPS4 as part of a NuVo Distributed Audio System
Page 6
Page 6
Audio Outputs
NuVoNet Connection
II. Accessing the Remote Configuration Tool
Accessing the Remote Configuration Tool from the Local Area
Network
Page 8
Page 8
Finding the IP Address for the NV-MPS4
III. Setting Up the NV-MPS4 through the Remote Configuration Tool
Machine Settings
Source Settings
Online Credentials
Firmware
Page 10
Page 11
Page 12
Page 13
IV. Loading and Using the Music Port Sync Tool
Loading the Music Port Sync Tool
Summary
iTunes
Windows Media
Other Content
Online Services
Page 14
Page 15
Page 15
Page 15
Page 16
Page 16
NV-MPS4 Specifications
Page 17
NV-NV-MPS4 Package Contents
·
NV-NV-MPS4 Music Port Server
1 pr. NV-REM1U single rack space Rack Ear Mounts
4 NV-RCA1 Stereo RCA audio cables
1 pr. NV-REM Rack Ear Mounts
1 NV-RS232 6 ft. 9 pin serial cable
1 NV-NC1 10 ft. black network cable
1 NV-NC10W 10 ft. white network cable
1 NV-PC2-NA Power Cable, 2 wire, North America
·
·
·
·
·
·
·
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The NV-NV-MPS4, or Music Port Server is designed to fully communicate with the NuVo Essentia, Grand Concerto and
Renovia Distributed Audio Systems through its NuVoNet communication protocol. Properly installing the Music Port Server
as a source component will provide full browsing to all of your personal music (both through iTunes and Media Player) as
well as online Internet radio.
Whether across the Web or from its internal 320 GB hard drive, the Music Port Server gives you full metadata feedback from
any of the NuVo Control Pads, and when it is controlled through the new NV-CTP36 Touch Pad controller, you will even
enjoy full color album art.
Through the Music Port Server, a world of music is at your fingertips.
NV-NV-MPS4 Music Port Server Wiring Diagram
AM/FM
3:09 pm
Modern Rock
Drift-Follow Th
Living For
MENU
OK
Concerto EZ Port
Model NV-I8GEZP
Device
1
Device
2
Device 3
Device
4
Device
5
Device 6
Connect to
NV-I8GM
NuVo Technologies LLC Hebron, Kentucky USA
www.nuvotechnologies.com
A
B
C
D
MODEL NV-NV-MPS4
Music Port Server
L
L
USB
USB
ETHERNET
Passthrough
RS232
To NuVo
RS232
NuVoNet
R
R
SYSTEM
AUDIO
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE 7&8
ZONE 1
2
ZONE 2
5
ZONE 3
ZONE 4
3
ZONE 5
3
ZONE 6
PROGRAM
1
2
1
4
SUM1
SYS ON
6
2
1
2
3
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
CONFORMS TO
4
5
6
SUM2
5
6
7
8
4
5
6
EXT. MUTE
UL STD.6500
1
2
3
4
5
6
C
US
CERTIFIED TO
CAN/CSA STD.E60065
3033118
SOURCE STATUS INPUTS
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM
NuVoNet
DIGITAL LINK
Diagram Shown with the NV-NV-MPS4 Music Port Server
connected to the Grand Concerto System.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232
POWER
1
2
3
4
5
6
7
8
NV-NV-MPS4 Music Port Server Front Panel Features
1. Power: This button supplies power to the Music Port Server when the unit is plugged into an AC power source and the
button is pushed.The associated blue LED will light.
2. USB Port: This USB port allow the Music Port Server to see and stream audio content from attached drives.This feature will
be available on a future release.
3. NuVoNet Error LED: The Music Port Server is designed to communicate via a CAT5 cable to the NuVo Essentia, Grand
Concerto, and Renovia Distributed Audio Systems.This red LED is designed to light indicating a lack of communication.With
normal communication, it will remain unlit.
4. LAN Error LED : This red LED will light when there is no Local Area Network signal present at the RJ45 Ethernet port on
the Music Port back panel, or when there is an interruption in the LAN signal. See page 8, Understanding the LAN Error
LED, for a detailed description of the different error states. In normal operation it will remain unlit.
5. RS232 Error LED: This red LED will light when the Music Port Server does not detect a serial connection at its DB9
output on the back panel.When a serial connection is present and active, the LED will remain unlit.
6. HDD Status LED: This green LED will light when the Music Port Server’s hard drive is active.
7. Source Address LED’s: These green LED’s 1 - 6 will light indicating the assigned source inputs on the
associated NuVo Distributed Audio System.
8. Reset Button: This recessed button will reset the Music Port Server’s operating system when it is pushed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
MODEL NV-NV-MPS4
Music Port Server
L
L
USB
USB
ETHERNET
To NuVo
RS232
NuVoNet
Passthrough
RS232
R
R
SYSTEM
AUDIO
1
2
3
4
5
6
7
NV-NV-MPS4 Music Port Server Back Panel Features
1. USB Ports: Three USB ports allow the Music Port server to see and stream audio content from attached drives.This feature
will be available in a future release.
2. Ethernet: This RJ45 port allows the Music Port Server to connect to the home’s network.This enables the music files on the
home’s network to be shared on the Music Port Server’s hard drive and the streaming of online Pandora, RadioTime™, SIRIUS
and XM Internet radio stations.
3. Passthrough RS232: The NuVo distributed audio systems are capable of being controlled serially by a third party home
automation system.This DB9 input is designed to pass incoming serial commands through to the adjacent RS232 output.This
allows both Client interface control from network computers of the attached NuVo audio system, and third party serial control
of the same NuVo system.
4. NuVo RS232 : This DB9 port connects to the attached NuVo distributed audio system.This allows any computer on the
home’s network to operate the Client interface for control of audio zones, source selection, and access to the music library. It
also works with the adjacent Passthrough RS232 port to send control commands from a third party home automation system
to the attached NuVo audio system.
5. NuVoNet: This RJ45 port connects to the attached NuVo distributed audio system and allows full source metadata display
and control from the NuVo system Control Pads.
6. Audio Outputs: The Music Port Server has four independent stereo RCA audio outputs that allow its audio streaming
content and stored music file audio signal to be sent to any audio distribution system or amplifier.
7. AC Power: A standard detachable IEC power cord supplies power to the NV-NV-MPS4. A switching power supply allows the
Music Port Server to operate world wide at any voltage.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Installing the NV-MPS4 as Part of a NuVo Distributed Audio System
The NV-MPS4 will fully communicate as a NuVoNet audio component with a few simple connections. Locate the NV-MPS4
component with the main component of the NuVo Distributed Audio System. Make all the connections first and plug it into
an AC power source and press the Power button on the front panel.The NV-MPS4 operating system will automatically boot
up.You will see considerable activity on the“HDD”hard drive status LED on the front panel during this process.This will take
approximately 60 seconds.
Audio Outputs
There are four independent audio outputs available to the NuVo System.These will be addressed through the Remote
Configuration tool, see II. Setting Up the NV-MPS4 Through the Remote Configuration Tool, page, 10 .
Connect the audio outputs from the NV-MPS4 to the desired audio inputs on the Essentia, Grand Concerto or Renovia
System using standard stereo RCA cables (four are supplied with the NV-MPS4 package) or if you are connecting to the
Renovia System, use stereo RCA to stereo mini 3.5 mm cables, Fig. 1.
Fig. 1
A
B
C
D
A
B
C
D
L
L
L
L
NV-MPS4 Audio
Outputs
NV-MPS4 Audio
Outputs
R
R
R
R
AUDIO
AUDIO
ZONE 1
ZONE 2
6
1
2
3
4
5
Essentia or Grand Concerto
Audio Inputs
1
2
3
4
5
6
SOURCE INPUTS
Renovia Audio
Inputs
NuVoNet Connection
Full communication with the NuVo Distributed Audio Systems is provided through a single CAT5 connection.This requires a
standard network CAT5 cable (one is provided in the NV-MPS4 package).
To make this connection to the Essentia or Grand Concerto Systems, plug the CAT5 into the“NuVoNet” RJ45 output on the
NV-MPS4 back panel and into one of the“Device”inputs on the Essentia Allport or the Grand Concerto EZ Port. Connect
another CAT5 from the Allport or EZ Port“NuVoNet”output to the input on the NuVo Distributed Audio System, Fig. 2.
Fig. 2
USB
USB
ETHERNET
To NuVo
RS232
NuVoNet
Passthrough
RS232
Concerto EZ Port
Model NV-I8GEZP
Device
1
Device
2
Device 3
SYSTEM
Device
4
Device
5
Device 6
Connect to
NV-I8GM
NuVo Technologies LLC Hebron, Kentucky USA
uvotechnologies.com
6
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are installing the Music Port Server with a Renovia System, plug the CAT5 directly into one of the three“NuVoNet”
inputs on the back panel of the Renovia Source Hub, Fig. 3.
Fig. 3
USB
USB
ETHERNET
To NuVo
RS232
NuVoNet
Passthrough
RS232
SYSTEM
II. Accessing the Remote Configuration Tool
The Remote Configuration Tool is a quick, easy setup for the operation of the Music Port Server. Once configured, it will be
fully operational with any of the NuVoNet Audio Distribution Systems.
Make sure the NV-MPS4 is plugged in, powered on, and connected to the home’s router through its“Ethernet”port. A live
Internet connection will cause the port LED’s to light green, Fig. 4. It is suggested that you use the white CAT5 cable for this
purpose to avoid confusing it with the NuVoNet cables.
Fig. 4
Green LED’s indicate a
live Ethernet connection
USB
USB
ETHERNET
ToNuVo
RS232
NuVoNet
Passthrough
RS232
SYSTEM
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding the LAN Error LED
The front panel of the NV-MPS4 has a red LED designed to alert you to communication issues across its network, Fig. 5.The
state of the LED indicates the nature of the problem.
LED not lit: This indicates good communication. No problem is found.
LED solid red: A cable connection at the“Ethernet”port on the back panel is not detected.
LED blinking twice: There is no WAN,Wide Area Network detected or no Internet connectivity.
LED blinking three times: This is no LAN, Local Area Network detected.
Fig. 5
RS232
LAN Error LED
Accessing the Remote Configuration Tool from the Local Area Network
Go to your computer and make sure it is connected to the same network as the NV-MPS4 (this is usually a wireless
connection). Open an Internet browser window and type the default name, music-port/config in the address bar, Fig. 5.
Fig. 5
This should open the Remote Configuration Tool, Fig. 6.
Fig. 6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding the IP Address for the NV-MPS4
If the“music-port”name does not connect, you can look up the IP address assigned to the Music Port Server and type that
into the browser address bar, i.e.. 192.168.0.124/config, Fig. 7.
Fig. 7
To find the address, go to the Menu of a Control Pad in the System. Choose one of the Music Port Server outputs from a
Control Pad. In the Menu, go to“Source Options”and then select“Source Info”. You will then see the selection“IP Address”.
Highlight is an press the“OK”button. This will display the Music Port Server’s IP address, Fig. 8.
Fig. 8
ain Menu
Albums
Genres
Version
IP Address
192.168.0.124
IP Address
Songs
Playlists
Source Options
Adv. Zone Control
OK
Setup
Another alternative is to open the Music Port Sync Tool to discover the NV-NV-MPS4.The IP address will appear in the
“Summary”Tab (note that the Sync Tool must be loaded on your computer), Fig. 9, see section IV. Loading and Using the
Music Port Sync Tool.
Fig. 9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Setting Up the NV-NV-MPS4 through the Remote Configuration Tool
Once you have opened the Remote Configuration Tool, setup of the Music Port Server is easy.
Machine Settings
The first tab of the setup utility is Machine Settings.The choices to note here are the Name Identification, time zone settings,
for monitoring the correct time from the web, and a choice of automatically configuring the NV-MPS4 on the home’s
network or assigning a static IP address.
Machine Identification: This is an option of renaming the Music Port Server from its default,“music-port”. This
is the name that will be used to access the server on the network and with the Music Port Client and Music Port
Sync Tool, see section IV. Loading and Using the Music Port Sync Tool, page 14, Fig. 10.
Fig. 10
Date and Time: This section allows you to specifiy a time zone and online server for monitoring the current time
from the Web. If you check the box,“Syncronize NuVo amplifier’s clock”it will automatically update the time on the
attached NuVo Distributed Audio System, Fig. 11.
Fig. 11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Wired Ethernet: The default is to let the network automatically supply an address to the Music Port Server
when is connected through the“Ethernet”port. If you choose, you can assign a static address using this drop-down
menu, Fig. 12.
Logging: This section is for technical support. If instructed to do so by a technical support person, you can upload
log files to NuVo Technical support for troubleshooting purposes.
When the“Machine Settings”choices are made, click “Save Changes”
Fig. 12
Source Settings: This tab simply sets a source address for the way in which you choose to connect the NV-MPS4 to the
NuVo System, Fig. 13. When these choices are made, click “Save Changes”. Make sure to select the appropriate number of
outputs you intend to use in the“Active Outputs”drop-down menu.
Fig. 13
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Content: Here is where you set the streaming capabilities of the Music Port Server. Supply the user account information in
each of the provider sections that apply to the intended use of the NV-MPS4, Fig. 14. Once this information is entered, click
“Save Changes”.
Fig. 14
Pandora Radio: Pandora is a free Internet music streaming service. Once you have created a Pandora account from your
computer, you simply enter your account information into the Pandora Radio section of the Content page. If you do not have
an account, you can establish one using the embedded link,“Click here to sign up for Pandora Radio”.
Radio Time: This is another free service. It is not necessary to have an account to access the available radio stations.The
account is necessary if you want the NV-MPS4 to be able to access presets created on Radiotime.com.
XM and SIRIUS Satellite Radio: These are subscription services with specialized programming. Note that you must
have four separate SIRIUS accounts to allow for four separate simultaneous streams from different stations.This is not true for
XM.
Contributing Computers: Listed here are all computers synced to the Music Port Server. To remove a contributing
computer click the ‘X’ listed to the left of the computer name. This will remove all content contributed by this computer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Firmware: This tab allows you to update the firmware, load the computer based Music Port Client control, and setup
music sharing with the Music Port Server, Fig. 15.
Fig. 15
Firmware Update: This download utility will prompt you when a new version is available.When you click on the supplied
link, the newest version will automatically update the NV-MPS4. If“No firmware update is currently available”appears, no
further action is necessary. It is important to note that the NV-NV-MPS4 is not updated over NuVoNet.
Other Software: There are two links here under the title“Music Port Client”, and a third application called the Music Port
Sync Tool are contained in this section.
Music Port Client: The Client is a network computer application that provides full control of the content both personal
and online streaming from any computer on the same LAN.When the RS232 serial connection is made to the NuVo Distributed
Audio System, the Client will also allow access to all of the System zones, and sources with basic source and zone control, see
section I. Installing the NV-NV-MPS4 as Part of a NuVo Distributed Audio System, page 6.
Start Music Port Client in this browser window: This link will open the Music Port Client
interface in an internet browser window.When the Client is open, it is easily saved as a“favorite”for future access.
This application is recommended for Mac users.
Install the Music Port Client stand alone application: This link opens an install wizard that installs the
Client as a standalone program on the PC. Once loaded the Client interface is easily accessed from a desktop icon. It
is important to load the Client on any user PC’s as part of the installation process of the Music Port
Server. For a detailed description of the Client interface see the Music Port Server User Guide.
Install the Music Port Sync tool stand alone application: This link will open an install wizard that loads
the Music Port Sync Tool on any networked PC.This is the application that allows content from your computer to be
shared with the Music Port Server and the associated NuVo Distributed Audio System.This tool wil be covered in the
next section, IV. Loading and Using the Music Port Sync Tool, page 14.
Support: The Remote Support section allows NuVo Technical Support to provide a security code to enable external access to
the Remote Configuration Tool.This is only used for troubleshooting purposes.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. Loading and Using the Music Port Sync Tool
The Music Port Sync Tool is a powerful application that allows any user network PC to contribute music to the Music Port
Server hard drive.
Loading the Music Port Sync Tool: You will find a link to the Music Port Sync Tool executable file in the Firmware
tab of the Remote Configuration Tool. Click on the link and open the file, Fig. 16.You will be prompted to save the .exe file
to a folder or run it from its current location.
Fig. 16
The executable will launch an installer program that loads the application on the user’s computer hard drive, Fig. 17.
Fig. 17
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Summary: The Summary tab provides overview of the Music Port Server. Here you will see the current operating version
and IP address, Fig. 18.The Summary tab will provide a progress report of any music sync activity.
Fig. 18
iTunes: This tab points to the actual library on the user’s hard drive, and syncs the chosen content with the Music Port
Server. Under“Sync Settings”, you have the choice to“Automatically update iTunes music”. This choice will allow you to
“Update all music”or “Update selected playlists”. Any selection made here will automatically sync with the NV-MPS4, Fig. 19.
The Music Port Server will not play M4P protected content purchased and downloaded from iTunes. As of
April of 2009 all content from iTunes is unprotected and compatible with the NV-MPS4.
Fig. 19
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Media: The Windows Media tab works like the iTunes tab.The choices and actions taken by the Music Port
Server are identical.The difference is that the Sync Tool is looking at the content in Windows Media Player. It is possible to
share content both from iTunes and Media Player, Fig. 20.
Fig. 20
Advanced: Rather than sharing music from a specific iTunes or Media Player library, you can point directly to a music
folder or directory on the network.This allows any music content to be placed in a shared directory for access by the Music
Port Server. Any music files copied to the shared folder will be seen by the Music Port Server and will automatically sync.
Click on“Add...”and this will open a window that allows you to browse folders on the network, Fig. 21.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 21
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Port Server
Specifications
Analog Audio Outputs
4
Power Requirements
Power Supply
Power Consumption
85-265VAC 50/60Hz
16W
Supported Audio Formats
Hard Drive Content
MP3
WMA
M4A
WAV
Physical Specifications
Unit Size Millimeters
Unit Size Inches
44 H x 430 W x 250 D
1 3/4 H x 17 W x 9 7/8 D
205 H x 515 W x 343 D
8 H x 20 1/4 W x 13 1/2
Shipping Size Millimeters
Shipping Size Inches
Internet Radio
Pandora
Sirius
XM
Unit Weight Kilograms
Unit Weight Pounds
Shipping Weight Kilograms
Shipping Weight Pounds
2.6
5.75
5.44
12.00
RadioTime
System Information
Hard Drive Capacity
320GB
Network Connection
Mbits/sec
NuVoNet Connection (RJ45)
NuVo reserves the right to change specifications without
notice.
10/100/1000
1
USB Connections (Type A)
Front Panel
Rear Panel
1
3
RS-232 Serial Connection
NuVo System
RS-232
Male DB-9
57,600 Baud
8 Data Bits
No parity
1 Stop Bit
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
NuVo Technologies LLC, Hebron, Kentucky USA
NV-MPS4
0952
Download from Www.Somanuals.com. All Manuals Search And Download.
|