NuTone Air Conditioner 9965 User Manual

INSTALLATION INSTRUCTIONS  
READ & SAVE THESE INSTRUCTIONS!  
Heat-A-Ventlite®  
934  
"
(with Night Light)  
MODEL: 9965  
734  
"
FOR BEST RESULTS  
In a new construction site, install the housing (complete  
with heater and ventilator) during rough-in construction of the  
building. The light assembly and the grille should be installed  
when the finished ceiling is in place.  
14"  
Installation in an existing, finished building requires an  
accessible area (attic or crawl space) above the planned  
location. See “INSTALLATION IN EXISTING  
CONSTRUCTION.”  
FIGURE 1  
Do not install closer than 12 inches to a vertical surface.  
Do not install over tub or shower enclosure.  
UNIT DIMENSIONS  
Refer to Figure 1 for housing's dimensions.  
NOTE: If there will be a finished second floor above,  
the Model 9965 housing requires a minimum of 2" x 8"  
joist construction for mounting.  
WIRING AND DUCTWORK  
1. Run the required wiring during rough-in stage of  
construction.  
HANGER BARS  
2. Total connected load: 1730 watts.  
3. Plan to run 120vAC, 60 Hz wiring (with ground) on a  
separate 20 Amp circuit from a power source, through  
the provided wall switch, to the housing's junction box.  
See wiring diagram.  
FIGURE 2  
JUNCTION  
BOX  
COVER  
4. Use 4" round duct.  
INSTALLATION IN  
NEW CONSTRUCTION  
PREPARATION  
1. Install hanger bar brackets in slots in housing. (See Fig. 3)  
Do not tighten completely to allow bars to be inserted.  
2. Refer to Figure 2. Insert hanger bars into brackets.  
3. Refer to Figure 3. Slide hanger bar brackets down to end  
of slot closest to outside edge of housing. Tighten brackets  
in this position.  
4. Refer to Figure 4. Remove junction box cover by  
ADJUSTMENT  
SLOT  
removing one screw.  
5. Refer to Figure 4. Remove appropriate wiring knockout(s)  
and install approved box connector(s).  
KNOCKOUTS  
FIGURE 3  
FIGURE 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION IN  
EXISTING CONSTRUCTION  
In an existing, finished building, installation of the Heat-  
Vent-Light Combination requires an accessible area (attic or  
crawl space) above the planned location. If the location that  
has been chosen for installation has a finished floor above it,  
be certain there is sufficient space available to install the  
housing and make the necessary duct connection.  
PLANNING  
Review “INSTALLATION IN NEW CONSTRUCTION” and  
follow all instructions that apply.  
CAUTION: Check the area above the planned location  
to make sure that:  
(1) Ducting can be installed.  
(2) Wiring can be run to the planned location.  
(3) No wiring or other obstructions might interfere with  
the installation.  
INSTALLATION  
1. The housing must be mounted between ceiling joists.  
2. Refer to Figure 10. Mark ceiling for cutout. Cutout  
dimensions: 1418" long x 978" wide. Make cutout in ceiling.  
3. Follow steps under “PREPARATION” page 1.  
4. From above, lower housing into the cutout and secure  
hanger brackets. Install duct collar, connect duct, and run  
wiring through box connectors.  
(LENS DETACHED  
IN DRAWING FOR  
ILLUSTRATIVE  
PURPOSES)  
LENS  
FIGURE 9  
5. From below, adjust housing so that it is flush with the  
finished ceiling.  
6. Form below, make wiring connections as shown in figure 6.  
7. Replace junction box cover.  
8. Insert heater, ventilator, light, and night light plugs into  
proper receptacles.  
9. install grille, reflector and lens.  
1418  
"
978  
"
WHITE  
HEAT  
VENT  
FIGURE 8  
FIGURE 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
One Year Limited Warranty  
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period  
of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED  
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.  
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES  
FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident,  
improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.  
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty  
lasts, so the above limitation may not apply to you.  
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS  
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH  
PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may  
not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.  
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model  
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present  
evidence of the original purchase date.  
Date of Installation  
Builder or Installer  
Model No. and Product Description  
IF YOU NEED ASSISTANCE OR SERVICE:  
For the location of your nearest NuTone Independent Authorized Service Center:  
Residents of the contiguous United States Dial Free 1-800-543-8687  
Please be prepared to provide:  
Product model number • Date and Proof of purchase • The nature of the difficulty  
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.  
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.  
Rev. 03/2001  
Product specifications subject to change without notice.  
Printed in U.S.A., Rev. 03/2001, Part No. 89356  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EFFECTIVE  
DATE  
PRODUCT  
GROUP  
MODEL NUMBER  
PARTS LIST  
MAY  
1999  
9965  
REVISED  
HEATER  
4
10  
11  
5
13a  
9
3
12  
7
6
14  
15  
8
9
2
13  
16  
17  
18  
24  
19  
1
VENT  
HEAT  
21  
20  
NIGHT  
LIGHT  
LIGHT  
22  
23  
NOT A PARTS DEPT.  
STOCK ITEM  
REF.  
NO.  
ORIGINAL  
PART NO.  
*PART DESCRIPTION  
REPLACEMENT  
PART NO.  
1
2
K3132  
K9010  
K3135  
K3136  
K3137  
K3097  
K3160  
K3096  
K3094  
K3143  
BEZEL/LENS ASSEMBLY  
89340-000  
89339-000  
89375-000  
35758-000  
35759-000  
66204-000  
57976-000  
56721-000  
57117-000  
30652-000  
GRILLE  
3
REFLECTOR  
4
SOCKET-LARGE  
5
SOCKET-SMALL W/CLIP  
RECEPTACLE-BLACK  
RECEPTACLE-BLUE WIRE  
RECEPTACLE-WHITE  
MOUNTING BRACKET (1) - 4 Required  
DUCT ADAPTOR  
6
7
8
9
10  
(PLEASE SEE OTHER SIDE)  
NOTE: Always order by  
current part number.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REF.  
NO.  
ORIGINAL  
PART NO.  
*PART DESCRIPTION  
REPLACEMENT  
PART NO.  
11  
12  
13  
13a  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
*
K3010  
K3117  
K3122  
82404  
K3121  
K3118  
K3102  
K3111  
K3110  
K3112  
K3360  
K3107  
K3146  
K3147  
K3148  
K9012  
HANGER ROD ASSEMBLY (1) 2 Required  
"B" UNIT ASSEMBLY-VENT  
BLOWER WHEEL  
85585-000  
86693-000  
82403-000  
82404-000  
89321-000  
2908A-000  
89306-000  
66583-000  
89315-000  
23255-000  
1179A-000  
89312-000  
85918-000  
85920-000  
85921-000  
89323-000  
PUSH NUT  
MOTOR (VENT)  
SCROWL (PLASTIC)  
"B" UNIT ASSEMBLY (HEAT)  
BLOWER WHEEL (HEAT)  
MOTOR (HEAT)  
MOTOR BRACKET  
THERMAL PROTECTOR  
HEATING ELEMENT  
SWITCH ASSEMBLY COMPLETE - HARDWARE BAG ASSEMBLY  
SWITCH PLATE  
SWITCH DOUBLE - (2 Required)  
GRILLE SCREW NOT SHOWN  
NOTE: Always order by  
current part number.  
9965 I.I.  
HEATER  
JUNCTION BOX  
HEATER  
LIGHT  
VENT  
(WHITE)  
BLK  
BLU  
RED  
BLK  
WHT WHT  
WHT WHT  
NIGHT  
LIGHT  
T
VENT  
HEAT  
LIGHT  
NIGHT  
LIGHT  
SWITCH  
BOX  
NOTE:  
WHEN THERMOSTAT  
OR TIMER IS USED,  
CONNECT AT  
T
120vAC  
LINE  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Charcoal Grill CS 1327 User Manual
Nesco Oven 18 Qt User Manual
Network Technologies TV Cables VOPEX C5SV x User Manual
Nike Heart Rate Monitor HRM SDM User Manual
Oce North America Printer OP14 User Manual
Omega Vehicle Security Welding System CCT 05 Series User Manual
Omnitron Systems Technology Network Card T3 E3 User Manual
Onkyo CD Player CDR 205X User Manual
PAC Car Satellite Radio System C2R VW2 User Manual
Patriot Products Blower RT5 CBV User Manual