Nilfisk ALTO Vacuum Cleaner S12cc User Manual

S12, S16  
Operating  
Instructions and  
Repair Parts List  
S12cc  
Upright Vacuum  
READ THIS BOOK  
This book has important information for the use and safe operation of this machine. Failure to read  
this book prior to operating or attempting any service or maintenance procedure to your ALTO  
machinecouldresultininjurytoyouortootherpersonnel;damagetothemachineortootherproperty  
could occur as well. You must have training in the operation of this machine before using it. If your  
operator(s)cannotreadthismanual,haveitexplainedfullybeforeattemptingtooperatethismachine.  
All directions given in this book are as seen from the operator’s position at the rear of the machine.  
For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.  
Form No. 70250A 7/01  
Clarke Technology  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in the U.S.A.  
OPERATOR SAFETY INSTRUCTIONS  
WARNING  
AVERTISSEMENT  
For the safe operation of this machine, read and understand all dangers, warnings and  
cautions. Look for these symbols:  
ADVERTENCIA  
DANGER:  
If you do not follow the instructions in a DANGER, severe bodily injury or death can occur to  
theoperatorand/orotherpersonnel.  
WARNING:  
If you do not follow the instructions in a WARNING, injury can occur to you or to other  
personnel.  
CAUTION:  
If you do not follow the instructions in a CAUTION, damage can occur to the machine.  
WARNING:  
To reduce the risk of fire, electric shock, or injury:  
1. You must have training in the operation of this machine before using it. READ THE  
INSTRUCTION BOOK.  
2. Do not use outdoors or on wet surfaces.  
3. Do not leave vacuum cleaner unattended when plugged in. Turn off the switch and unplug  
the electrical cord when not in use and before servicing.  
4. Do not allow to be used as a toy. Close attention is necessary when used by or near  
children.  
5. Use only as described in this manual. Use only manufacturer's recommended attachments.  
6. Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has  
been dropped, damaged, left outdoors, or dropped into water, return it to a service center.  
7. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull a cord  
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away  
from heated surfaces.  
8. Connect to a properly grounded outlet only (refer to Grounding Instructions).  
9. Do not use extension cords or outlets with inadequate current carrying capacity.  
10. Turn off all controls before unplugging.  
11. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.  
12. Do not handle plug or vacuum cleaner with wet hands.  
13. Do not put any objects into openings. Do not use with any opening blocked, keep free of  
dust, lint, hair, and anything that may reduce airflow.  
14. This vacuum cleaner creates suction and contains a revolving brush. Keep hair, loose  
clothing, fingers and all parts of body away from openings and moving parts.  
15. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot  
ashes.  
Page -3-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING:  
To reduce the risk of fire, electric shock, or injury:  
16. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt  
pulley when servicing the drive belt.  
17. Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas  
where they may be present.  
SAVE THESE INSTRUCTIONS  
Page -4-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GROUNDING INSTRUCTIONS  
Grounded  
Outlet Box  
Preparation:  
The following are instructions for connection to the  
power supply and the electrical ground.  
This machine must be connected to the electrical ground to  
protect the operator from electrical shock. The machine has  
an approved power cord with three conductors and a plug  
with three terminals. Connect the plug to a receptacle that  
has three holes and is connected to the electrical ground.  
The green (or green and yellow) conductor in the cord is the  
ground wire. Never connect this wire to any terminal other  
than the ground pin terminal.  
Grounding Blade  
is longest of the  
three blades  
FIGURE A  
DANGER:  
Improper connection of  
the equipment-grounding conductor can result  
in risk of electric shock. Check with a qualified  
electrician or service person if you are in doubt  
as to whether the outlet is properly grounded.  
Do not modify the plug provided with the  
appliance. If it will not fit the outlet, have a  
proper outlet installed by a qualified  
electrician.  
Grounded  
Outlet Box  
This machine is for use on a 110 to 120 Volt AC 60 cycle  
electric circuit. Make sure you have the correct frequency  
and voltage before connecting the power cord to an outlet.  
The machine has a plug as shown in figure A. If a receptacle  
connected to the electrical ground as shown in figure A is not  
available, use an adapter as shown in figure C. This adapter  
must be connected as shown in figure B to an electrical  
ground in the electrical outlet. Make sure you use the plate  
screw and the tab to fasten the adapter.  
Adapter  
Metal  
Screw  
WARNING: Always use this machine with an AC  
three-conductor electrical system connected to  
the electrical ground. Replace any worn, cut or  
damaged cords. Replace any damaged plugs,  
receptacles or connector bodies.  
Grounding  
Tab  
FIGURE C  
FIGURE B  
WARNING: Do not cut, remove, or break the  
ground terminal. Do not try to fit a three-termi-  
nal plug into a receptacle or connector body  
that does not fit the plug, see your Authorized  
ALTO Dealer to get an authorized person to  
make the connection.  
WARNING: Do not move the machine over an  
electrical cord. Always lift the cord over the  
machine.  
EXTENSION CORDS:  
Use only an approved extension cord with three conductors,  
a plug with three terminals and a connector body with three  
holes. This machine has a power cord with wire size 18  
AWG (AWG means American Wire Gauge).  
WARNING: If you use an extension cord, use an  
extension cord with minimum wire size 16 AWG.  
Do not use an extension cord longer than 50  
feet. Do not join two extension cords.  
Page -5-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSIGNES DE SÉCURITÈ DE L'UTILISATEUR  
AVERTISSEMENT  
Pour utiliser cet appareil en toute sécurité, il faut lire et coprendre tous les consignes de danger,  
d'avertissement et d'attention. Soyez attentif aux symboles que voici.  
DANGER:  
Ne pas respecter les consignes d'un avis de DANGER, peut occasionner la mort ou des  
lesionscorporellesgravespourl'utilisateuret/oud'autrespesonnes.  
AVERTISSEMENT: Ne pas respecter les consignes d'un AVERTISSEMENT peut occasionner des lesions  
corporellespourl'utilisateuret/oud'autrespersonnes.  
ATTENTION:  
Ne pas respecter les consignes d'un avis d'ATTENTION peut occasionner des dommage  
à l'appareil.  
AVERTISSEMENT:  
Pour réduire le risque de feu, de choc électrique, ou de blessure:  
1. Vous devez recevoir une formation appropriée avant de vous servir de cet appareil. LISEZ  
LEMANUELDECONSIGNESDUFABRICANT.  
2. Ne pas utiliser à l'extérieur ou sur des surfaces mouillées.  
3. Ne laissez pas l'aspirateur seul quand il est branché. Fermez le commutateur et débranchez  
l'appareil lorsque vous ne l'utilisez pas ou avant le nettoyage ou l'entretien.  
4. Ne permettez pas que l'aspirateur soit utilisé comme un jouet. Une attention particulière est  
nécessarie lorsqu'il est utilisé par ou près d'un enfant.  
5. Suivez strictement les recommandations d'utilisation de ce manuel. Utilisez uniquement les  
accessoires recommandés par le fabriquant.  
6. N'utilisez jamais l'aspirateur si le cordon ou la fiche sont endommagés. Si l'aspirateur ne  
foncitionne pas comme il le devrait, s'il a été échappé, s'il est endommagé, s'il a été laissé à  
l'extérieur ou échappé dans l'eau, retournez-le à un centre de service avant de l'utiliser.  
7. Ne tirez pas l'aspirateur ou le transportez par le cordon. N'utilisez pas le cordon en guise  
de poignée. Ne fermez pas uen porte sur le cordon ou tirez le cordon sur des bordures ou  
des coins pointus. Ne passez pas l'aspirateur sur le cordon. Tenez le cordon à distance  
des surfaces chauffantes.  
8. Branchez toujours l'aspirateur dans une prise à trois (mise à terre).  
9. N'utilisez pas des rallonges ou des prises qui n'ont pas une capacité suffisante pour  
transporter le courant.  
10. Mettez sur arrêt tous les boutons de commande avant de débrancher.  
11. Ne débranchez pas l'aspirateur en tirant sur le cordon. Pour débrancher, tenez la fiche et  
non pas le cordon.  
12. Ne manipulez pas la fiche ou l'aspirateur avec les mains mouillées.  
14. N'insérez rien dans les ouvertures. N'utilisez pas l'aspirateur si des ouvertures sont  
bloquées. Assurez-vous qu'elles soient dégagées de poussière, de mousse, de cheveux  
ou de tout autre chose qui pourrait réduire le passage de l'air.  
15. Cet aspirateur crée de la succion et contient une rouleau-brosse tournant. Tenez les  
parties mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie  
du corps.  
Page -6-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AVERTISSEMENT:  
Pour réduire le risque de feu, de choc électrique, ou de blessure:  
16. Ne remassez pas de objets qui brûient ou fument comme les cigarettes, les allumettes ou  
les cendres chaudes.  
17. Les poulies de la courroie peuvent devenir chaudes pendant l'utilisation normale. Pour  
prévenir des brûlures, évitez de toucher la poulie lors de l'entretien de la courroie.  
CONSERVEZ CES INSTRUCTIONS  
Page -7-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTRUCTIONS VISANT LA MISE A LA TERRE  
PREPARATION:  
Consignes pour brancher l'appareil a la source d'energie  
et pour la mise à la terre.  
Boîte de Prise  
de Terre  
Cet appareil doit être mise à la terre afin d'eviter le risque de  
choc électrique. Cet appareil est pourvu d'un cordon muni de  
trois conducteurs et d'une fiche munie de trois bornes.  
Brancher la fiche à une prise qui a trois tous et est mise à la  
terre. Le conducteur vert (ou vert et jaune) dans le cordon  
est le fil neutre. Ne jamais attacher ce conducteur à une  
borne autre que la borne à terre.  
LALAMEDE  
TERREESTLA  
PLUSLONGUE  
DESTROIS  
LAMES  
DANGER:  
Un conducteur de terre  
mal raccordé peut entraîner un risque de choc  
électrique. Consulter un electricien ou un  
technicien qualifié si vous n'êtes pas certain  
que la prise est correctement mise à la terre. Ne  
pas modifier la fiche fournie avec l'appareil. Si  
elle ne peut être insérée dans la prise, faire  
installer une prise adéquate par un électricien  
qualifié.  
FIGURE A  
Note:AuCanada, l'utilisationd'unadaptateur  
temporaire n'est pas autorisée par le Code  
canadien de l'électricité.  
Cet appareil est destiné à un circuit de 110 à 120 volts et 60  
cycles. S'assurer que l'appareil est branché à une prise de  
courant ayant la même configuration que la fiche. Cet  
appareil est muni d'une fiche de mise à la terre semblable à  
celle illustrée par la Figure A.  
AVERTISSEMENT: Toujours employer cet  
appareil avec un système électrique AC à trois  
conducteurs, raccordé à la mise à la terre.  
Remplacer tout cordon usé, coupé ou  
endommagé. Remplacer toute fiche ou prise  
endommagée.  
AVERTISSEMENT: Ne pas couper, briser, ou  
enlever la prise de terre. Ne pas chercher à  
brancher la fiche à trois bornes, à une prise que  
ne lul correspond pas. Si la prise ne correspond  
pas à la fiche, contacter votre agent de vente  
autorisé des appareils Clarke Technology afin  
qu'une personne qualifiée effectue le  
branchement.  
AVERTISSEMENT: Ne pas faire passer l'appareil  
sur le cordon électrique. Soulever toujours le  
cordon pour faire passer l'appareil en dessous.  
LES RALLONGES:  
Utilise seulement une rallonge approuvée à trois fils  
conducteurs, munie d'une fiche à trois bornes et d'une prise  
à trois trous. Cet appareil est muni d'un cordon électrique  
dont les fils sont de calibre 16 AWG (AWG signifie American  
Wire Gauge).  
AVERTISSEMENT: Si vous utilisez une rallonge,  
celle-ci doit avoir un calibre de fil minimum de  
16 AWG. Ne pas utiliser de rallonge qui dépasse  
50 pieds (15 mètres) de long. Ne pas raccorder  
deux rallonges ensemble.  
Page -8-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO PREPARE THE MACHINE FOR OPERATION  
Assemble the Handle  
Attach upper (A) and lower (B) handle to handle  
socket (C) by aligning holes and securing with 2 part  
screws (D). See figure 1.  
A
D
Install the Bag Assembly  
Position the bag coupling into the left bag support (A)  
and turn the bag knob (B) counterclockwise to secure  
bag to base. Attach bag spring to bag hook (C)  
located on the rear of the top cord hook. See figure  
2.  
B
D
C
On the Collector Cup Model, the lower handle fits  
through the tube on the front of the collector cup  
frame.  
Figure 1  
HOW TO OPERATE THE MACHINE  
With power cord plugged into the proper voltage  
outlet, lower handle to start the vacuum. Lower  
handle by depressing handle release pedal at the  
lower left rear of the vacuum. Depress pedal again  
and lower handle all the way to the floor to clean  
under low furniture.  
C
To stop vacuum, raise handle to upright position.  
For handle positions, see figure 3.  
B
A
Figure 2  
Store  
Operate  
Clean Under  
Figure 3  
Page -9-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
This section describes the procedures that must be  
done by the operator.  
Motor Pulley  
WARNING: To prevent injury, always turn  
off the switch and remove the electrical  
plug from the electrical outlet before  
changing the brush, belt, or filter bag and  
before leaving the machine.  
WARNING: To prevent electrical shock,  
always turn off the switch and remove the  
electrical plug from the electrical outlet  
before doing any repairs or maintenance  
to this machine.  
Figure 4  
WARNING: Belt pulleys can become hot  
during normal use. To prevent burns, do  
not touch the belt pulley when servicing  
the drive belt.  
WARNING: Maintenance and repairs must  
be done by authorized personnel only.  
Belt  
Guide  
The Belt to Drive the Brush  
This machine uses a round rubber belt to drive the  
brush. Check the belt frequently. Replace the belt if  
the belt slips on the brush. Remove hair and threads  
from the brush roll and the motor shaft pulley before  
replacing the belt.  
How to Replace the Belt  
To replace the drive belt, follow this procedure:  
1. Make sure the electrical plug is removed from the  
outlet.  
Figure 5  
2. Put the machine upside down.  
3. To remove the bottom plate, turn the two cam  
latches on the sides of the plate.  
4. Remove the worn belt from the pulley on the motor  
shaft. See figure 4.  
5. To remove the brush, pull the brush out of the slots  
in the frame.  
6. Clean the vacuum opening in the base of the  
machine.  
7. Check the bristles of the brush for wear. If the  
bristles are worn, see the section "What to Do  
about the Wear of the Brush."  
8. Put a new belt around the pulley on the brush.  
Align the brush roll pulley with the belt guide. See  
figure 5.  
Page -10-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE (CONT.)  
9. Place the rubber end cap covers over both end  
caps (flat side against end cap). Align holes and  
secure. Then, slant the brush roll forward so the  
end caps are in line with the slots in the cleaner  
base. Push the brush roll into the base until  
seated. See figure 6.  
10. Place the lower side of the belt into the belt guide  
and around the left side of the motor pulley. See  
figure 7.  
Figure 6  
CAUTION: Improper installation of the  
brush roll or brush roll belt could cause  
carpet or cleaner damage.  
11. To install the chrome bottom plate, put the tab on  
the base in the slot in the plate. Press the center  
of the plate against the base of the machine. Turn  
the cam latches to fasten the plate to the base.  
See figure 8.  
What to Do About the Wear of the Brush  
Figure 7  
1. Make sure the electrical plug is removed from the  
electrical outlet.  
2. Put the machine upside down.  
Cam Latch  
3. To remove the bottom plate, turn the two cam  
latches on the sides of the plate.  
Tab  
Figure 8  
Page -11-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE (CONT.)  
Steel Core Brush  
WARNING: Turn off the switch and disconnect  
unit from electrical supply before replacing  
brush strips.  
F
E
1. New brush strips inserts are supplied in sets. To  
replace, first disconnect the machine from the  
electrical outlet.  
2. Remove the brush roll, see the section "How to  
Replace the Belt."  
A
B
C
D
3. Take the rubber end cab cover (figure 6, itemA) from  
the end of the brush roll and unscrew the locknut  
(figure 9, item B).  
Figure 9  
4. Remove end cap (figure 9, item C) and bearing  
retainer (figure 9, item D).  
5. Push the exposed end of the shaft (figure 9, item E)  
through the opposite end of the brush roll.  
6. Pull out the worn brush strip (figure 9, item F) with  
pliers and slide in a new one of the same length,  
inserting the rounded end first.  
7. Fit the track on either side of the brush strip securely  
into the brush roll slot.  
D
8. Replace the second brush strip from the opposite end  
of the brush roll.  
Figure 10  
9. Return shaft (figure 9, item E) and align the  
indentation of the bearing retainer (figure 10, item D)  
with the brush strip on both ends. Seat firmly.  
10. Position the end cap (figure 9, item C) with the flat  
side of the center hole over the flat side of the  
threaded shaft (figure 9, item E).  
11. Tighten locknut (figure 9, item B).  
12. Add the end cap cover (figure 9, item A) flat side down  
and secured over the four end cap projections.  
13. When properly assembled, the brush roll should rotate  
freely between the two end caps.  
14. Check the condition of the belt; change if necessary.  
Replace the roll belt bottom plate, see the section  
"How to Replace the Belt".  
Lubrication  
Do not oil the motor. The motor in this machine is  
permanently lubricated and sealed. Do not oil the motor at  
any time.  
Electrical Maintenance  
WARNING: Electric repairs and maintenance  
must be done by authorized personnel only.  
Return the machine to a Alto Authorized  
repair location.  
Page -12-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING GUIDE  
PROBLEM  
Motor does not run.  
POSSIBLE CAUSE  
1) Not firmly plugged in.  
2) Bad On-Off switch.  
3) Line open.  
SOLUTION  
1) Check attachment plug.  
2) Replace switch.  
3) Replace cord.  
4) Motor open.  
5) Fan locked by material.  
4) Check motor and wiring.  
5)Removeobstruction.  
Motor runs but cleaner  
does not pick up.  
1) Belt broken.  
2) Blocked air system.  
3) Fan broken.  
4) Worn brush roll.  
5) Motor slow.  
1) Replace belt.  
2)Cleanobstruction.  
3)Replacefan.  
4) Replace brush roll.  
5) Check carbon brushes.  
6) Empty bag (or change paper bag).  
6) Bag full.  
Motor runs erratically.  
Brushrollvibrates.  
1) Worn carbon brushes.  
2)Defectivearmature.  
3) Bad electrical connection.  
4)DefectiveOn-Offswitch.  
1)Replacebrushes.  
2) Check spark, replace armature.  
3) Check wiring.  
4) Replace switch.  
1) Ball bearing worn out.  
1) Replace brush roll.  
2)Ballbearingholderdamaged.  
2)Replaceballbearingholder.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Wiring Diagram 11/00  
Page -13-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Collector Cup Assembly Drawing 7/01  
108  
Page -14-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Collector Cup Assembly Parts List 7/01  
Ref. Part No. Description  
Qty  
2
80065A  
56489A  
Screw (M4 *10)  
Screw (M4 *15)  
E-clip (E6)  
Screw (M4 * 8)  
HandleGrip  
HandleAssembly,Upper  
BagHook  
Bag Retainer  
CordRetainer,Upper  
Screw (M4 *25)  
1
23  
5
3
1
1
1
1
1
3
1
2
2
2
1
1
2
1
1
1
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
2
1
1
26  
31  
35  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
95  
96  
97  
56485A  
30138A  
51240A  
30143A  
30144A  
30142A  
80127A  
51278A  
80129A  
80128A  
51237A  
30139A  
Washer, Upper Cord Retainer  
Spring,UpperCordRetainer  
Nut,Handle  
Screw,Handle  
HandleAssembly,Lower  
CordRetainer, Lower  
Screw (M4 * 45)  
HandleSocketSeatAxle  
HandleSocketTube  
HandleSocketCam  
Power Cord  
Bushing,HandleSocket  
Seat,HandleSocket  
Nut,HandleTube  
Clamp, Handle Socket Cam  
Spring,Bag  
Clip, Bag (Chrome)  
BagCoupling  
BagCouplingGasket  
Dust Bag  
Bag Frame (incl. w/bag asm.)  
Bag Clamp Plate (incl. w/bag asm.) lower  
Bag Clamp Plate (incl. w/bag asm.) upper  
Seal,UpperHose  
Cup Frame  
51243A  
51241A  
51244A  
51357A  
51242A  
30156A  
51358A  
30154A  
51263A  
51262A  
30148A  
30149A  
51359A  
51266A  
51267A  
51268A  
30145A  
30146A  
98  
99  
100 51360A  
101 51265A  
102 51264A  
103  
104 30147A  
105 51269A  
106 619221  
107 30150A  
Gasket, Cup Frame  
Dust Cup  
Side Clip, Cup  
Screw (M4 *9)  
ExhaustHose  
Clamp  
CableTie  
Hose,InletCurved  
108 52362ACollector Cup Assembly  
NOTE: indicates a change has been made since the last publication  
of this manual.  
Page -15-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Base Assembly Drawing 1/01  
Page -16-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Base Assembly Parts List 1/01  
Ref. Part No. Description  
Qty.  
1
2
1
6
4
1
1
2
1
1
2
1
1
1
2
1
4
1
1
1
2
1
3
2
2
4
23  
1
1
2
1
5
1
1
1
3
2
1
Ref. Part No. Description  
Qty.  
1
2
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
4
3
2
1
1
1
2
3
4
5
6
7
8
51229A  
80065A  
51949A  
80066A  
HoodandGraphics  
Screw (M4 *10)  
CableClip  
Screw (M4* 18.5)  
Washer (4.2 *12*1)  
MotorAssembly  
MotorExhaust(LH)  
Exhaust Foam  
Power Switch  
38  
39  
40  
41  
51261A  
Clamp,FrontAxle  
Screw(M3*10)  
DriveBelt  
12" Bristle Strip Set (4 strips)  
16" Bristle Strip Set (4 strips)  
12" Brush Roll  
16" Brush Roll  
Shaft - 12"  
903340  
51253A  
51255A  
51348A  
51230A  
30161A  
40178A  
51245A  
42  
43  
51251A  
51252A  
51353A  
30140A  
30141A  
51354A  
51250A  
51227A  
51228A  
30136A  
30137A  
30158A  
80051A  
51235A  
30159A  
51238A  
51260A  
51239A  
51234A  
51236A  
51355A  
30160A  
51232A  
51356A  
9
Shaft - 16"  
BearingSupport  
Cover, Cap  
End Cap  
Washer, Felt  
Bearing  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
Switch Clip  
44  
45  
46  
47  
48  
49  
Screw (M3 *12)  
StrainReliefBushing  
BushingBracket  
FootPedal  
Spring,PedalReturn  
Knob,Bag  
Screw (M4 *20)  
BagSupport  
12" Base Assembly  
16" Base Assembly  
Nut(M4)  
30157A  
30135A  
51256A  
51259A  
30152A  
57951A  
30151A  
30098A  
30099A  
12" Bottom Plate Assembly  
16" Bottom Plate Assembly  
12"FurnitureGuard  
16"FurnitureGuard  
HeightAdjustmentCam  
Screw(M3*6)  
Clip, HeightAdjustmentCam  
Seat, HeightAdjustmentCam  
Gear,HeightAdjustment  
Spring,HeightAdjustment  
Axle,HeightAdjustment  
CrankGear,HeightAdjustment  
CrankAxle,HeightAdjustment  
Spring,PedalSupport  
Crank,HeightAdjustment  
MotorExhaust(RH)  
HeightIndicator  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
51270A  
RearAxle  
Washer (8.5*16*1)  
Nut,Cap(F-Type)  
Rear Wheel  
Clamp, WheelAxle  
Screw (M4 *15)  
Cam (RH)  
30155A  
51271A  
56489A  
51233A  
51231A  
Cam (LH)  
Washer (4.1*8*1)  
Spring,FrontAxle  
E-Clip (E6)  
Rod,FrontAxleSupport  
FrontAxle  
FrontAxleSeat  
Screw(M4*8)  
Front Wheel  
51257A  
108  
109  
110  
111  
NI*  
NI *  
NI *  
Switch Wire -16#  
Switch Wire -18#  
Washer (4.2*14*1)  
Nut,Cap(M4)  
Carbon Brush  
Impeller  
51272A  
51351A  
56485A  
30153A  
51352A  
51365A  
51366A  
51367A  
Plate,FrontAxleSupport  
MotorPulley  
*NI = Not illustrated  
Page -17-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum\  
Handle and Filter Bag Assembly Drawing 7/01  
Page -18-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKETECHNOLOGY  
Symphony Upright Vacuum  
Handle and Filter Bag Assembly Parts List 7/01  
Ref. Part No. Description  
26 56489A Screw(M4*15)  
Qty.  
23  
5
31  
E-Clip (E6)  
35 56485A Screw(M4*8)  
3
70 30138A HandleGrip  
1
71 51240A Handle Assembly - Upper Chrome  
72 30143A BagHook  
1
1
73 30144A Bag Retainer  
1
74 30142A CordRetainer-Upper  
1
75  
Screw(M4*25)  
3
76 80127A Washer, Upper Cord Retainer  
77 51258A Spring,UpperCordRetainer  
78 80129A Nut,Handle  
1
1
2
79 80128A Screw,Handle  
2
80 51237A Handle Assembly - Lower Chrome  
81 30139A Cord Retainer - Lower  
1
1
82  
Screw(M4*45)  
2
83 51243A Axle, Handle Socket Seat - Plated  
84 51241A Tube, Handle Socket - Plated  
85 51244A Cam, HandleSocket  
86 51357A Power Cord, Symphony  
87 51242A Bushing,HandleSocket  
88 30156A Seat,HandleSocket  
89 51358A Nut,HandleTube(M4)  
90 30154A Clamp, Handle Socket Cam  
91 52363ACloth Filter Bag Assembly  
92 51263A Spring,Bag  
1
1
1
1
3
1
2
1
1
1
93 51262A Clip, Bag (Chrome)  
94 51248A Dust Bag (long)  
1
1
96 30148A BagCoupling  
1
97 30149A Gasket,BagCoupling  
98 10246ABag, Paper Filter Assembly  
99  
1
1
100 660638Bag, Paper Filter 3 pk  
101 52360ABag,Cloth,Zipper  
102 52361ACable,Tie,Reuseable  
103 30147AExhaustHose  
104 619221CableTie  
105 30150AHose,Inlet  
1
1
1
1
2
1
NOTE: indicates a change has been made since the last  
publicationofthismanual.  
Page -19-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
Page -20-  
CLARKE TECHNOLOGY Symphony Upright Vacuum Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ALTO® PRODUCT SUPPORT BRANCHES  
U. S. A. Locations  
European Locations  
HEAD OFFICE  
PRODUCTION FACILITIES  
ALTO U.S.Inc., St. Louis, Missouri  
16253 Swingley Ridge Road, Suite 200  
Chesterfield, Missouri 63017-1725  
ALTO Danmark A/S, Aalborg  
Blytaekkervej 2  
DK-9000 Aalborg  
+45 72 18 21 00  
PRODUCTION FACILITIES  
ALTO Danmark A/S, Hadsund  
Industrikvarteret  
ALTO U.S.Inc., Springdale, Arkansas  
2100 Highway 265  
DK-9560 Hadsund  
+45 72 18 21 00  
Springdale, Arkansas 72764  
(501) 750-1000  
Customer Service - 1-800-253-0367  
Technical Service - 1-800-356-7274  
SALES SUBSIDIARIES  
ALTO Canada Ltd., Rexdale Ontario  
24 Constellation Ct.  
ALTO U.S.Inc., Bowling Green, Ohio 43402  
1100 Haskins  
(416) 675-5830  
ALTO U.S.Inc., Clearwater, Florida 33765  
1500 N. Belcher Road  
ALTO Overseas Inc., Sydney (Australia)  
1B/8 Resolution Drive  
Caringbah NSW 2229  
+61 2 9524 6122  
SERVICE FACILITIES  
ALTO Cleaning Systems Asia Pte Ltd., Singapore  
No.17 Link Road  
ALTO U.S. Inc., Carlstadt, New Jersey 07072  
150 Commerce Road  
Singapore 619034  
(201) 460-4774  
+65 268 1006  
ALTO U.S. Inc., Elk Grove, Illinois 60007  
2280 Elmhurst Road  
ALTO Deutschland GmbH, Frondenberg (Germany)  
Ardeyer Str. 15  
(847) 956-7900  
D-58730 Frondenberg  
+49 2373 754 200  
ALTO U.S.Inc., Denver, Colorado 80204  
1955 West 13th Ave.  
ALTO Cleaning Systems (UK) Ltd., Penrith  
Gilwilly Industrial Estate  
Penrith  
(303) 623-4367  
ALTO U.S.Inc., Houston, Texas 77040  
7215 North Gessner Road  
Cumbria CA11 9BN  
+44 1768 868 995  
ALTO France S.A.Strasbourg  
B.P. 44, 4 Place d’Ostwald  
F-67036 Strasbourg  
Cedex 2  
SALES AND SERVICE FACILITIES  
ALTO U.S.Inc., Madison Heights, Michigan 48071-0158  
+33 3 8828 8400  
29815 John R.  
(810) 544-6300  
ALTO Nederland B.V.Vianen  
Stuartweg 4C  
ALTO U.S.Inc., Marietta, Georgia 30062  
1355 West Oak Common Lane  
(770) 973-5225  
NL-4131 NJVianen  
+31 347 324000  
ALTO Sverige AB, Molndal (Sweden)  
Aminogatan 18  
CLARKE TECHNOLOGY  
AMERICAN SANDERS TECHNOLOGY  
A.L. COOK TECHNOLOGY  
Customer Service Headquarters and Factory  
2100 Highway 265  
Box 4029  
S-431 04 Molndal  
+46 31 706 73 00  
ALTO Norge A/S, Oslo (Norway)  
Bjornerudveien 24  
N-1266  
Springdale, Arkansas 72764  
(501) 750-1000  
+47 2275 1770  
Technical Service  
1-800-356-7274  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLARKE TECHNOLOGY U.S. WARRANTY  
This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and work-  
manship under normal use and service for a period of one year from the date of purchase, when operated  
and maintained in accordance with Clarke's Maintenance and Operations instructions.  
This warranty is extended only to the original purchaser for use of the product. It does not cover normal  
wear parts such as electrical cable, rubber parts, hoses and motor brushes.  
If difficulty develops with the product, you should:  
(a). Contact the nearest authorized Clarke repair location or contact the Clarke Service Operations Depart-  
ment, 2100 Highway 265, Springdale, Arkansas 72764, for the nearest authorized Clarke repair location.  
Only these locations are authorized to make repairs to the product under this warranty.  
(b). Return the product to the nearest Clarke repair location. Transportation charges to and from the repair  
location must be prepaid by the purchaser.  
(c). Clarke will repair the product and or replace any defective parts without charge within a reasonable time  
after receipt of the product.  
Clarke's liability under this warranty is limited to repair of the product and/or replacement of parts and is  
given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUENTIAL DAMAGES.  
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO  
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES,  
INCLUDING BUT NOT LIMITED TO WARRANTY OF MECHANTABILITY, SHALL BE IMPLIED. A warranty  
registration card is provided with your Clarke product. Return the card to assist Clarke in providing the  
performance you expect from your new floor machine.  
ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.  
CLARKE TECHNOLOGY reserves the right to make  
changes or improvements to its machine without notice.  
Always use genuine Clarke Parts for repair.  
CLARKE TECHNOLOGY  
2100 Highway 265  
Springdale, Arkansas, 72764  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop KM89 2 User Manual
NCR Home Theater Screen NCR 5972 User Manual
NordicTrack Home Gym NTL149053 User Manual
Nortel Networks Telephone C4012 User Manual
Oki Printer ES 2024 User Manual
Oreck Vacuum Cleaner XLPRO6 User Manual
Oregon Scientific Thermometer THN122N User Manual
Oregon Weather Radio EMR201A User Manual
Palsonic CRT Television 9219SF User Manual
Panasonic Saw EY3530 User Manual