NVS 6
PILOT NIGHT VISION
GOGGLES
MAINTENANCE AND OPERATION
MANUAL
In USA: 3310 Prospect Ave. Cleveland, OH 44115
In Canada: 1183 Finch Ave. W., Suite 302, Toronto, ON M3J 2G2 Canada
Tel: (416) 663-6963 Fax: (416) 663-9065
Email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
IMPORTANT INFORMATION
Read prior to activation
You have just purchased a complicated electronic device. To operate it
properly, please read this manual carefully. Here are some common
precautions that must be noted.
•
•
NEVER disassemble the unit. This device contains high voltage, which may
be hazardous to your health!
NEVER expose the opened objective lens of an active unit in daylight. At
daytime objective lens must be covered by caps. There is a tiny hole in the
cap to provide enough light for daytime testing. It is allowed to turn on the
unit at daytime, but caps must cover the lenses.
•
•
NEVER aim active unit at intense light sources
(i.e. lights, headlamp, campfires, the moon, etc.)
NEVER reverse the polarity of a battery
● ALWAYS remove batteries when not in use for a long period
• ALWAYS keep the objective lenses covered when not in use
•
ALWAYS store in a warm dry place when not in use
RECORD OF REVISIONS
Pages 1/2
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
RECORD OF REVISIONS
Page
Rev. Section,
No. Sub-Section,
Subject
Authorizing Transmittal letter
Document Reference No. Signed Date
Revi-
sed
Dele-
ted
Added
No.
and date
by
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
LIST OF EFFECTIVE PAGES
Section,
Sub-Section,
Subject
Section,
Sub-Section,
Subject
Page
Date
Page
Date
Title Page
–
–
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Record of
Revisions
1/2
List of Effective
Pages
1/2
Table of Contents 1/2
General
1
2
Main Data
Standard Set
3
4
5
6
Operation Proce-
dure
Safety Precautions
Design of Unit and
Its Components
7
8
Operational
Status Check
Trouble Shooting
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Maintenance
Practices
Preparation for
Operation
Storage and
Shipment
LIST OF EFFECTIVE PAGES
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages 1/2
NVS 6
MANUAL
TABLE OF CONTENTS
Page
1 General........................................................................................................ 1
2 Main Data .................................................................................................... 3
3 Standard Set................................................................................................ 5
4 Safety Precautions....................................................................................... 7
5 Design of Unit and Its Components............................................................. 8
6 Preparation for Operation .......................................................................... 19
6.1 Preparation of Helmet for Mounting Night-Vision Goggles...................... 19
6.2 Individual Adjustment and Fitting............................................................. 22
6.3 Arrangement of Night-Vision Goggles on Helicopter............................... 32
7 Operation Procedure ................................................................................. 36
8 Operational Status Check.......................................................................... 38
9 Trouble Shooting ....................................................................................... 40
10 Maintenance Practices ............................................................................ 44
11 Storage and Shipment............................................................................. 49
APPENDIX A ................................................................................................. 51
APPENDIX B ................................................................................................. 52
CONTENTS
Pages 1/2
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
1 General
1.1 The NVS 6, helicopter night-vision goggles, have been
designed for use by the helicopter crewmembers during execution of
flights at night.
Note – The helicopter cockpit should be tailored for the use of the
night-vision goggles. Accounting for the spectral content of the light
equipment radiation, color of the cockpit interior surfaces, and the like.
1.2 The NVS 6 provides napping off the earth while piloting the
helicopter at low altitudes, at takeoff, hovering and landing, including
landing on unprepared and non-illuminated landing sites.
1.3 When using the NVS 6, the pilot can take the readings of the
instruments by looking at the instrument panel in the downward direction
or sideways past the eyepieces.
1.4 The NVS 6 operates within the ambient temperature range of
minus 40 to +40oC.
1.5 The power supply to the NVS 6 is powered by the helicopter
electrical system of 27V, via the voltage converter or from the
independent power source (IPS). The IPS is built-in to the goggles and
consisting of two batteries of type size AA R6 1.5V or from rechargeable
batteries of the same type.
Note – The IPS (independent power source) is used when the
aircraft electrical power is lost or the helicopter power supply has failed.
1.6 The NVS 6 shall be used under the following conditions:
– When the natural night illumination intensity is within 5·10-3 to 1 lx
and the meteorological visibility is 1 to 10 km
– At a flight altitude of 20 to 200 m;
– At a flight speed of up to 120 km/h.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 1
NVS 6
MANUAL
1.7 The trouble-free operation of the NVS 6, within the assigned
service life, is ensured through its correct use, careful handling and well-
timed maintenance.
1.8 When operating the unit or placing it in storage, keep it clean
and avoid touching the external optical surfaces of the lenses and
eyepieces with fingers. Protect the unit against impact or dropping which
may cause damage and defects to the unit and render it inoperable.
1.9 Before using the NVS 6, carefully read this Manual.
1.10 In the course of the service of the unit, enter the information
pertaining to its operational status, maintenance, storage and repair in the
Log Book.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
2 MAIN DATA
2.1 Specifications of the NVS 6 are presented in Table 1.
Table 1
Specification
1 Field of view (FOV), minimum
Characteristic
40 deg
2 Magnifying power
1 X
3 Resolving power limit of the image intensifier
tube, as measured in the center of FOV, minimum
50 lines per mm
4 Dioptric setting range of eyepieces, minimum
5 Interpupilary distance range
6 Lens focusing distance range
7 Power supply:
-6/+2 D
52 to 72.7 mm
0.25 m to infinity
– From helicopter DC electrical system via a
voltage converter
24.0 to 29.4 V
– From two batteries of type size AA R6 1.5 V 2.2 to 3.2 V
or rechargeable batteries
8 Current consumed with the unit powered from
helicopter electrical system, maximum
100 mA
9 Power consumed with the unit powered from
helicopter electrical system, maximum
3 W
10 Continuous operation time of the unit powered 3 h
from the built-in independent power source without
changing the batteries (within the entire operating
temperature range), minimum
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Table 1, cont'd
Specification
Characteristic
11 Continuous operation time followed by an
interval of not less than 30 min, minimum
3 h
12 Unit deployment time (getting the unit ready 5 min
for use), maximum
13 Unit stowing time (packing the unit in the
case), maximum
5 min
14 Mass, maximum:
– Night-vision goggles (without mount)
– Voltage converter with cable
0.59 kg
0.3 kg
15 Night-vision goggles overall dimensions,
maximum
108x151.5x122 mm
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
3 STANDARD SET
3.1 The standard set of the NVS 6 shall be consistent with Table 2
and Fig. 3.1.
Table 2
Designation
Nomenclature
Assemblies
Qty
Remarks
201211.010
Night-vision goggles
Voltage converter
Set of Spare Parts
Dehydrator cartridge
1
1
433739.003
279376.002
1
Optional
Set of Tools and Accessories
Watchmaker’s
screwdriver MT-992, size
1.5
1
Optional
754421.001
Test pattern
1
4
Optional
Optional
Batteries of type size
AA R6 1.5 V
304134.001
745159.003
745159.001
305259.001
741112.013
Mount
1
1
1
1
3
Casing
Clamp
Counterweight
Cloth
Optional
Packaging
Soft Padded Case
325371.009
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
NVS 6
MANUAL
8
7
12
1
10
9
2
11
6
3
4
5
7
Mount
Casing
Clamp
1 Night-Vision Goggles
2 Voltage Converter
3 Dehydrator Cartridge
4 Screwdriver
8
9
10 Counterweight
11 Cloth
5 Test Pattern
12 Case
6 Batteries
NVS 6 Standard Set
Figure 3.1
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
4 SAFETY PRECAUTIONS
4.1 The NVS 6 is constructed so as to provide pilot’s safety during
operation.
4.2 In case of emergency the helicopter crewmembers shall take
off (throw off) the NVS 6 night-vision goggles before evacuating the
helicopter.
To ensure successful removal of the unit, the crewmember using
the NVS 6 in flight should be trained to quickly execute the night-vision
goggles. In an emergency evacuation from the helicopter expedient
removal is essential for his/her safety.
4.3 Care should be taken to protect the unit from direct exposure of
its lenses to high-level optical radiation.
CAUTION: NEVER SWITCH ON THE UNIT DURING DAY LIGHT
UNLESS PROTECTIVE CAPS ARE INSTALLED ON THE UNIT
LENSES. DO NOT KEEP THE UNIT IN THE BRIGHT LIGHT SOURCES
FOR LONG PERIODS OF TIME.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
NVS 6
MANUAL
5 DESIGN OF UNIT AND ITS COMPONENTS
5.1 The NVS 6 is essentially a passive-type optoelectronic night-
vision device whose principle of operation is based on the intensification
of image brightness of objects being viewed with the aid of image-
intensifier tubes.
5.2 The NVS 6 design employs a binocular pattern, i.e. it consists
of two identical optoelectronic channels (of monocular type) which afford
stereoscopic vision to create comfortable conditions for napping off the
earth, thus enabling the pilot to evaluate the space depth and ensure
higher night flight safety.
5.3 The general view of the NVS 6 is illustrated in Fig. 5.1.
5.3.1 Lenses (1) may be focused either relative to distant objects
located in the space outside the cockpit, or relative to the objects located
close to the helicopter. The focus is adjusted by rotating the lenses.
5.3.2 The dioptric focusing of eyepieces (2) is carried out
individually for each sight channel of the unit by rotating eyepieces with
the aid of focusing rings (3).
5.3.3 The independent power source (IPS) is arranged inside
guide (4), which is closed with cap-switch (5).
5.3.4 The NVS 6 is installed onto the pilot’s helmet by attachment of
fixing assembly (6) of the unit to mount (7), which is then secured to
helmet casing (8).
The fixing assembly makes it possible to perform individual
adjustment, so as to provide the most comfortable position of the goggles
mounted on the helmet relative to the pilot’s eyes. This feature enables
the pilot to move the goggles away from the eyes, tilt the optical axes of
monocular pair and displace them upwards and downwards.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 8
NVS 6
MANUAL
7
18
20
19
6
4
17
13
8
16
9
1
10
12
14
Lens
2
3
5
15
11
1
2
3
4
5
6
7
8
9
11 Cable
12 Cap
Eyepiece
Ring
13 Dehydrator Cartridge
14 Sight Glass
15 Cable
Guide
Cap-Switch
Fixing Assembly
Mount
16 Screw
17 Visor Guard
18 Slot
Casing
Counterweight
19 Cross-Shaped Knob
20 Screw
10 LVC (Low-Voltage Converter)
NVS 6
Figure 5.1
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
For balancing out the overturning momentum produced by the unit
in the operating position, use is made of counterweight (9) secured on the
rear portion of the helmet.
The helmet should be tailored for employment of the night-vision
goggles. For this purpose, the standard casing should be replaced and
the strip of the sticking fastener should be bonded to the helmet rear
surface for attachment of the counterweight (the necessary appliances
are included in the set of spare parts).
Note: other helmets may require different mounting mechanisms
5.3.5 Caps (12) are intended to safeguard the image intensifier
tubes against exposure to light and protect the optical components of
the lenses from mechanical damage.
The caps are provided with holes for checking the night-vision
goggles for serviceability at an illumination intensity of more than 1 lx (in
conditions of day light and dusk), as well as with retainers (two spring-
loaded projections located on the cap sides) used for reliable locking of
the cap in the mount of lens (1).
Small projections in the sides of the cap are provided, with holes for
joining the caps, in pairs by means of a fishing line. This will minimize
their inadvertent loss in service.
5.3.6 The moisture-resistance of the unit is ensured with the use of
annular rubber seals and dehydrator cartridges (13). These are intended
to absorb moisture in case it gets into the interior space of the monocular
pair. The dehydrator cartridge is filled with silica gel that is bluish in color
when it is not saturated. As the silica gel gets saturated, it turns rose-pale
or off-white. The external condition of the silica gel is monitored through
sight glass (14).
5.4 The NVS 6 standard set comprises the night-vision goggles, the
voltage converter and the single set of spare parts. (Optional)
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 10
NVS 6
MANUAL
16
13
14
22
17
15
21
18
9
3
1 10
4
В
В
Б
Б
А
А
2
5
7 8
6 10 12 19
20
9
10
1
1 Guide
2 Guide
3 RH Side Monocular
4 LH Side Monocular
5 Lens
6 Eyepiece
7 Image-Intensifier Tube
8 Barrel
9
Screw
16 Cable
17 Lever
18 Knob
19 Screw
20 Plate
10 Button
11 Batteries
12 Cap-switch
13 Fixing Assembly
14 Retainer
15 Button
21 Retainer
22 Retainer
Night-Vision Goggles
Figure 5.2
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Physically, the night-vision goggles are made in the form of two
identical electro-optical channels – monocular (3) and monocular (4) –
which are mechanically linked with each other with the aid of guide (1)
and guide (2). Each of the monocular pair incorporates lens (5), eyepiece
(6), image-intensifier tube (7) and barrel (8).
RH side monocular (3) that allows the pilot to carry out observation
with the right eye is rigidly fastened to guide (2), while LH side monocular (4)
that permits observation with the left eye is of a movable design and may
be displaced to adjust the eyepieces of the night-vision goggles to suit the
pilot’s eyes.
To adjust the night-vision goggles interpupilary distance, depress
button (10) and displace monocular (4) along guide (2) to set it to the
desired position. These done, release the button to fix monocular (4) in
the selected position.
Batteries (11) are installed inside guide (2) and closed with cap-
switch (12).
The night-vision goggles are attached to the helmet with the aid of
the guides of fixing assembly (13) and those of the helmet mount. The
fixing assembly is retained in the fixed position in the helmet mount by
means of retainer (14).
The transfer of the night-vision goggles from the stowed position to
the operating one, in which they are fitted on the helmet, is accomplished
by depressing button (15) with the left hand and lowering the goggles until
they are retained in the locked position. The fixing assembly is provided
with a connector, for connecting the mating connector plug of cable (16),
intended to feed power to the night-vision goggles via the voltage
converter.
Upon termination of use, the night-vision goggles are easily
removed complete with cable (16) from the mount of the helmet by
pressing down lever (17).
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 12
NVS 6
MANUAL
Knob (18) provides a means of individual adjustment of the
monocular position (eye relief, tilt of the monocular pair optical axes, and
displacement of the monocular pair in the upward and downward
directions).
The monocular pair is locked in the selected position by moving the
knob down as far as it will go. This securely locks the monocular pair in
this position. The force applied for tightening the knob is adjustable. This
adjustment is performed after releasing the hinged joint by turning screw
(19) about its axis. To carry out the adjustment, pull out plate (20) that
retains the screw in position and turn it complete with the screw to the
next fixed position. In so doing, remember that the knob retaining force
becomes greater as the plate is turned clockwise and vice versa.
The night-vision goggles can be promptly removed from the pilot’s
field of view and transferred to the stowed position.
To do so, take hold of the monocular pair and, while overcoming
the force of retainer (21), move it fully upwards to the stowed position. As
the monocular pair is brought to a stop, the retainer will operate to hold it
up in the stowed position.
The electrical circuits, in this case, will become automatically de-
energized through activation of the microswitch.
5.4.2 Voltage converter (2) is illustrated in Fig. 3.1.
The voltage converter is designed to supply power to the NVS 6 from
the helicopter electrical system.
The voltage converter consists of two separate components: low-
voltage converter (LVC) (10) and cable (11) as shown in Fig. 5.1.
The LVC is a stabilized DC power source used to convert the
helicopter electrical power of 27V DC to 2.6V DC to power the unit.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
The design of the LVC is illustrated in Fig. 5.3. Structurally, the LVC
consists of casing (1), which accommodates voltage converter (2)
attached to it by means of screws (3). Cover (4) is fastened to the casing
with screws (5). Connector plug (6) serves to connect the LVC to the
helicopter electrical system of 27 V with the aid of the cable arranged on
board the aircraft.
Connector receptacle (7) is intended to connect cable (11), shown
in Fig. 5.1, to the LVC.
Connector plug (6) and connector receptacle (7) are secured to the
casing by means of screws (8) as shown in Fig. 5.3.
Gaskets (9) installed between the casing, the connector plug and
the receptacle serve to protect the LVC interior against direct entry of
moisture, whereas LVC cover (4) is filled with sealing compound for the
same purpose. Cable (11) attached to the voltage converter is connected
to cable (15) to make an electric power supply circuit of the night-vision
goggles as shown in Fig. 5.1.
The use of cables with quick-disconnect connectors makes it
possible to promptly remove the night-vision goggles from the helmet in
case of emergency.
5.5 Apart from spare dehydrator cartridge, the single set of spare
parts includes the following: test pattern, mount, casing, clamp,
counterweight, screwdriver, cloth, spare batteries or rechargeable
batteries. Spare parts availability is optional, to be specified in each
individual supply contract.
5.5.1 Test pattern (5), shown in Fig. 3.1, is designed for checking
the quality of the image of the NVS 6 (resolving power). The check
procedure is presented in 6.2.21 of this Manual.
5.5.2 The mount, shown in Fig. 5.4, is intended to secure the
NVS 6 on the helmet of the pilot or a helmet of a similar type.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 14
NVS 6
MANUAL
4
1
3
8
7
5
2
А1
XS1
XP1
9
6
1 Casing
4 Cover
5 Screw
6 Connector Plug
7 Connector Receptacle
8 Screw
2 Voltage Converter
3 Screw
9 Gasket
Low-Voltage Converter
Figure 5.3
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
3
5
6
1
7
1 Screw
2 Screw
3 Screw
4 Guides
5 Spring
6 Carriage
7 Carriage
8 Screw
2
9
Screw
8
4
9
Mount
Figure 5.4
The mount is attached to the front portion of the helmet with the aid
of three screws (1), (2), (3).
The night-vision goggles are secured to the mount by means of a
night-vision goggle plate, which is passed into the slots of guides (4) of
the mount.
The purpose of spring (5) is to reliably retain the NVS 6 on the
mount.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 16
NVS 6
MANUAL
Carriages (6) and (7) can be moved upwards/downwards by
rotating adjustment screw (8), as well as left/right with the aid of screw (9)
to adjust the position of the night-vision goggles relative to the pilot’s eyes.
The adjustment is performed with the use of the screwdriver, part of the
single set of spare parts.
5.5.3 Casing (8), shown in Fig. 3.1, is intended for replacing the
helmet standard casing, which makes it possible to fasten the night-vision
goggles. Three holes provided at the casing center are used for installation
of mount (7) as shown in Fig. 5.1. After attaching the casing on the
external surface of the helmet front portion with four screws (16), it
protects visor guard (17) against any possible damage. Slots (18) are
used as guides when lowering and lifting the visor guard. They help to
hold the visor guard in the required position with the use of retainer cross-
shaped knob (19) moving along the slot of the casing, together with the
visor guard. While replacing the casing, the retainer cross-shaped knob
can be installed for using by the right or left hand of the pilot.
5.5.4 Clamp (9), shown in Fig. 3.1, is meant for fastening the visor
guard when replacing the standard casing for the casing found in the set
of spare parts. The clamp together with the visor guard fastened in it is
attached to the casing with the help of the retainer shown in Fig. 6.1.
5.5.5 Counterweight (10), shown in Fig. 3.1, is intended to
compensate for the tilting momentum produced by the unit.
The counterweight is essentially an individual assembly consisting
of a canvas cover with a weight contained therein. As shown in Fig. 5.1,
counterweight (9) can be quickly installed on the rear portion of the helmet
through the use of the sticking fastener. The mass of the counterweight is
620 g.
The counter weight also has a strap with a sticking fastener used
for securing night-vision goggles power cable (15).
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 17
NVS 6
MANUAL
5.5.6 Screwdriver (4), shown in Fig. 3.1, is meant for performing
necessary readjustments of mount (7) and also used when the helmet
standard casing is replaced.
5.5.7 For removing dust, moisture and dirt from the external
surfaces of the unit, use is made of cloth (11) shown in Fig. 3.1.
5.5.8 The rechargeable batteries included in the single set of spare
parts, serve for replacement of failed or exhausted batteries of the
independent power source. The rechargeable batteries are charged by
the use of a standard battery charging unit designed for charging the AA
type rechargeable batteries in accordance with the Manual furnished with
the charging unit.
5.6 The packaging components of the NVS 6 include the case and
the set of maintenance documents (the Manual and the Log Book).
5.6.1 The case, shown in Fig. 3.1, is used for storing and carrying
the NVS 6 set. The case is provided with side pockets, which are
fastened with a zipper. One pocket holds the LVC (low-voltage converter)
and the cables, and the other one is used for holding the mount,
counterweight and screwdriver. The inner pocket is intended for
accommodating the test pattern, cloths, spare dehydrator cartridge and
batteries or rechargeable batteries. The night-vision goggles and its
accessories are delivered sealed in a polyethylene film envelope, which is
packed in the case together with the casing and clamp. The case is
closed with a flap fastened with a zipper and a sticking fastener. The case
comes complete with a carrying strap.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
6 PREPARATION FOR OPERATION
6.1 Preparation of Helmet for Mounting Night-Vision Goggles
6.1.1 Replacement of Visor Guard/Mount Assembly
6.1.1.1 Remove the standard mount assembly of visor guard (17)
(Ref. Fig. 5.1). To do this, remove four screws (16) attaching the casing to
the helmet using the screwdriver found in the set of spare parts.
6.1.1.2 To disconnect the visor guard from the standard casing:
(a) Remove screw (20) with the screwdriver by turning it clockwise.
(b) Remove cross-shaped knob (19) by hand.
(c) Remove retainer (1) (Ref. Fig. 6.1) together with the visor guard
from the standard casing slot.
(d) Remove the visor guard from the retainer by first turning
retainer tail end (2) along the visor guard slot.
6.1.1.3 Take clamp (9) shown in Fig. 3.1 from the set of spare parts.
6.1.1.4 Remove screw (3) with the screwdriver as shown in Fig. 6.2
and remove bushing (4) from the clamp hole.
6.1.1.5 insert the visor guard into clamp slot (5) accurately without
turning askew and applying much force, and fasten it using a bushing and
a screw.
6.1.1.6 Take casing (8) out of the set of spare parts. Connect the
clamp, together with the visor guard secured in it, to the casing. To do
this, insert retainer tail end (2) along recess (6) of the clamp (left-hand or
right-hand at the option of the pilot) and turn it crosswise the recess as
shown in Fig. 6.2.
6.1.1.7
Pass the retainer threaded portion through the
respective (left-hand or right-hand) slot of casing (8)
and proceed as in Steps 6.1.1.2 (b), 6.1.1.2 (a) and
6.1.1.1 observing the mentioned order.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
20
19
18
7
9
3
17
5
+
4
8
2
1
1 Retainer
6 Recess
17 Visor Guard
18 Slot
2 Tail End
3 Screw
7 Washer
8 Casing
9 Clamp
19 Cross-shaped Knob
20 Screw
4 Bushing
5 Recess
Replacement of Casing on Helmet
Figure 6.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 20
NVS 6
MANUAL
1
2
1 Retainer
2 Tail End
6 Recess
9 Clamp
9
6
Assembly of Clamp with Retainer
Figure 6.2
6.1.2 Installation of Counterweight
6.1.2.1 Take counterweight (10) (Ref. Fig. 3.1) from the set of spare
parts, remove the backing of the sticking fastener meant for fastening to
the helmet.
6.1.2.2 Bond the removed
fastener to the rear potion of the
helmet external surface so that the
hole made at the center of the
fastener coincides with screw head
(1) (Fig. 6.3), the lower edge of the
fastener therewith should join to the
helmet rubber edging. Before bonding
with adhesive trace the outline of the
fastener on the helmet and
thoroughly remove the paint from the
helmet within the outline.
Figure 6.3
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 21
NVS 6
MANUAL
6.1.2.3 The adhesive recommended for usage is acrylate cyanide,
type LOCTITE 454, or the like providing an adequate bonding of
fiberglass laminate with polyvinyl chloride (the adhesive sets in 2 to 3 min
and the unit may be used after a lapse of 24 h). For the bonding
procedure, refer to the Instructions for Cement Usage.
6.1.2.4 While bonding the fastener press its smooth side to the
helmet surface evenly without applying an excessive force. Apply
pressure to the fastener total area and use a screw clamp for locking the
parts to be bonded (Uniformly press the sticking fastener against the
helmet until its strip is bonded to the helmet, use should be made of the
suitable device).
6.2 Individual Adjustment and Fitting (Figs 6.4 thru 6.6)
CAUTION: EACH PILOT SHOULD CARRY OUT INDIVIDUAL
FITTING AND ADJUSTMENT OF THE NIGHT-VISION GOGGLES.
Before starting the adjustment check to see that the lenses are
closed with safety caps.
6.2.1 Remove the night-vision goggles from the case.
6.2.2 Depress button (1) (Ref. Fig. 6.4) and, while holding the fixing
assembly in one hand, take monoculars (28) and (29) in the other hand,
transfer the goggles to the operating position so that the fixing assembly
is straightened. In doing so, see that only a slight force is applied to
securely lock (latch) the monocular pair in the operating position,
indicated by a click of retainer (21) (Ref. Fig. 5.2).
CAUTION: IN THE EVENT OF FAILURE OF THE RETAINER TO
LATCH THE MONOCULAR PAIR IN THE OPERATING POSITION, THE
NIGHT-VISION GOGGLES WILL NOT BE ENERGIZED AND THE
INDIVIDUAL ADJUSTMENT WILL NOT BE POSSIBLE.
6.2.3 To ensure proper latching, essential for retaining the
monocular pair in the operating position, check to see that the hinged joint
linking the monocular pair to the unit fixing assembly is reliably locked.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 22
NVS 6
MANUAL
Should the monocular pair fail to be locked relative to the unit fixing
assembly, proceed as follows:
– Move knob (2) (Ref. Fig. 6.4) to the top position (the hinged joint,
in this case, will be fully released).
– Pull out plate (3), which retains screw (4) in the locked position,
with your thumb and forefinger, turn it to the next locking position in the
clockwise direction and release the plate. The plate shall be set to a new
locking position (Ref. Step 6.2.2).
– This done, lock the hinged joint linking the monocular pair to
the unit fixing assembly again by applying an effort to knob (2) so as to
bring it down as far as it will go.
If the monocular locking continues to fail, carry out the above
procedure one more time.
6.2.4 Take power supply components (two batteries of type size AA
R6 1.5V or rechargeable batteries) out of the case. When using the
rechargeable batteries, first charge them in accordance with the Manual
furnished with the battery-charging unit.
6.2.5 Insert two batteries into the recess of guide (8) with the positive
contact directed inwards by first unscrewing and removing cap-switch (5),
and then screw it in fully in the clockwise direction.
6.2.6 Release knob (2) and set the top portion of the fixing assembly
perpendicular to the axes of monocular (28) and monocular (29). While
holding the fixing assembly in one hand, displace the monocular pair with
the other hand forward and downward until they are butted up against the
cruciform guides of the fixing assembly. Once completed, tighten the
knob to lock the monocular pair in the desired position.
WARNING: NEGLECT OF THE REQUIREMENTS DESCRIBED IN
THE ABOVE STEP MAY RESULT IN EYE INJURY DURING THE
COMPLETION OF FURTHER PREPARATORY OPERATIONS.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
14
16 26 12 27 13 16 27
1
11
18
9
2
10
29
3
4
25
28
8
7
6 5
1 Button
2 Knob
9
Counterweight
16 Screw
18 Lever
10 Strap
3 Plate
11 Cross-head Knob
12 Guide
13 Retainer
14 Cable
15 Visor Guard
25 Connector
26 Mount
27 Screw
28 LH Side Monocular
29 RH Side Monocular
4 Screw
5 Cap-switch
6 Cap
7 Button
8 Guide
Installation of Night-Vision Goggles on Helmet in Operating Position
Figure 6.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 24
NVS 6
MANUAL
2
12 13
16
14
27
26
27
17
5
4
3
1
18
9
10
25
1 Button
10 Strap
12 Guide
17 Ring
2 Knob
18 Lever
3 Plate
13 Retainer
14 Cable
16 Screw
25 Connector
26 Mount
27 Screw
4 Screw
5 Cap-switch
9 Counterweight
Night-Vision Goggles Installed on Helmet in Stowed Position
Figure 6.5
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 25
NVS 6
MANUAL
2 6
1 2
1 6
1 3
2 7
1
1 8
3
4
7
2
1 Button
2 Knob
3 Plate
4 Screw
7
Button
18 Lever
26 Mount
27 Screw
12 Guide
13 Retainer
16 Screw
Installation of Night-Vision Goggles on Helmet and Their Adjustment
Relative to Pilot’s Eyes
Figure 6.6
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 26
NVS 6
MANUAL
14
12
13
1
22 23 19
15
2
21
20
24
15
1
Button
19 LVC (Low-Voltage Converter)
20 Cable
21 LVC Power Cable Running from
Helicopter Electrical System
22 Receptacle
23 Plug
24 Spring Clamp
25 Connector
12 Guide
13 Retainer
14 Cable
Connection of Night-Vision Goggles to Helicopter Electrical System Via
Voltage Converter
Figure 6.7
6.2.7 Position the eyepieces of the goggles at eye level, turn on the
night-vision goggles by turning cap (6) of cap-switch (5) in the
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
counterclockwise direction until it is retained in the ON position and check
to see that the unit operates properly. In so doing, see to it that the
image-intensifier tube screens start glow steadily in amber-green
(without flashes and twinkling) in the monocular pair of the night-vision
goggles.
CAUTION: TO SAFEGUARD THE UNIT AGAINST DAMAGE, MAKE
ABSOLUTELY SURE THAT THE SAFETY CAPS ARE FITTED ON THE
LENSES WHEN THE NIGHT-VISION GOGGLES ARE TURNED ON IN
THE PRESENCE OF LIGHT.
6.2.8 Depress button (7) and displace LH side monocular (28) with
respect to the immobile RH side monocular, along guide (8) to
preliminarily select the optimum distance between the eye pupils in
accordance with the interpupilary distance of the operator. Release button
(7) and the LH side monocular will be locked in the selected position.
6.2.9 Turn cap (6) of cap-switch (5) in the clockwise direction as far
as it will go to de-energize the night-vision goggles.
6.2.10 Take hold of the monocular pair with one hand and the fixing
assembly with the other hand, and transfer the night-vision goggles to the
stowed position as shown in Fig. 6.5 (i.e. fold up the fixing assembly by
overcoming the retainer force that locks the goggles in the operating
position).
6.2.11 Remove mount (26), part of the single set of spare parts,
designed for attaching the night-vision goggles, from the outer pocket of
the case and install it on the front portion of the helmet. To do so, insert
three screws (27) into the threaded holes in the helmet casing and tighten
them.
6.2.12 Remove counterweight (9) (Ref. Fig. 6.4) from the outer
pocket of the case, install it on the rear portion of the helmet and secure it
by means of the sticking fastener.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
6.2.13 Carry out preparatory operations on the pilot’s helmet in
compliance with the Manual. Loosen cross-shaped knob (11) and use it to
move visor guard (15) fully so that the visor guard is retracted under the
casing. These done, fix the visor guard in this position by tightening the
cross-shaped knob.
6.2.14 Install the night-vision goggles, which are currently placed in
the stowed position, onto the helmet (with the helmet removed from the
head), by joining the fixing assembly of the night-vision goggles to the
helmet mount. To do so, insert the plate of the fixing assembly of the
night-vision goggles into the slots of guide (12) (Ref. Fig. 6.4) of helmet
mount (26). Exercise due care to avoid misalignment, then, turn the plate
upwards until retainers (13) become latched.
6.2.15 Attach cable (14) to the helmet by first passing it under
unfastened strap (10) on counterweight (9) and then fasten the strap
using the sticking fastener.
6.2.16 Secure the helmet, complete with the goggles placed in the
stowed position, on the pilot’s head.
6.2.17 Transfer the goggles to the operating position (Ref. Step 6.2.2
of this Manual) and turn them on (Ref. Step 6.2.7 of this Manual).
6.2.18 Set RH side monocular (29) precisely opposite the right eye
of the pilot. To do so, ease up knob (2) and displace the monocular pair of
the night-vision goggles in the cruciform guides of the fixing assembly
upward or downward, forward or backward. Simultaneously turn them
about the axis of knob (2) to find the optimum position at which the NVS 6
monocular pair is properly set away from the eyes and their optical axes
have the required tilt.
By an optimum position of the monocular pair relative to the pilot’s
eyes, is meant, a position that provides adequate conditions for carrying
out observation of the full field of view of the RH side monocular with the
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
right eye, as well as clear view of the surrounding space by shifting gaze
downwards under the eyepieces of the night-vision goggles.
Note – If the RH side monocular of the night-vision goggles fails to
be set to the position at which the sighting line of the pilot’s eye passes
through its center, the position of the RH side monocular shall be
corrected by moving the night-vision goggles upwards or downwards,
right or left relative to the helmet. To do so, the carriages of helmet mount
(26) should be shifted by the adjustment of screws (16) utilizing the
screwdriver provided (Ref. Fig. 6.6). On completion of the corrective
actions, perform the operations described in this step once again.
6.2.19 Carry out the operations prescribed by Step 6.2.8 of this
Manual to finally adjust the interpupilary distance.
Make sure that the full field of view of the night-vision goggles is
provided for both eyes.
6.2.20 Adjust the eyepieces to the appropriate dioptric sighting by
turning rings (17) (Ref. Fig. 6.5) of the eyepieces until a sharp structural
image of the screens on the image-intensifier tubes is attained.
6.2.21 Evaluate the operational status of the night-vision goggles
by checking the image quality (resolving power). For this purpose, take a
test pattern, from the single set of spare parts and arrange it at a distance
of an outstretched hand away from the lenses ((750 16) mm). The
settings of the night-vision goggles are considered to be normal if the test
pattern lines are clearly visible and the check text is readable. Both
monoculars should operate without flashes and twinkling.
CAUTION: THE SERVICEABILITY CHECK OF THE NIGHT-
VISION GOGGLES SHALL BE ACCOMPLISHED IN THE PRESENCE
OF LIGHT WITH THE LENSES COVERED BY THE SAFETY CAPS.
6.2.22 De-energize the night-vision goggles (Ref. Step 6.2.9 of this
Manual).
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 30
NVS 6
MANUAL
6.2.23 Check the operation of the mechanism permitting
emergency removal of the night-vision goggles from the helmet. To test,
depress levers (18) (Ref. Fig. 6.4) of the fixing assembly with the thumb
and forefinger and simultaneously pull the night-vision goggles promptly
downwards. As the night-vision goggles become released from the guide
on the helmet, keep on moving your hand to the left and right side to
disengage the power cable from the helmet. The night-vision goggles shall
easily separate from the mount of the helmet and remain in the pilot’s
hands.
Regardless of the position, operating or stowed, the night-vision
goggles will be easily removed.
WARNING: THE NIGHT-VISION GOGGLE REMOVAL TO BE
PERFORMED IN THE EVENT OF AN EMERGECY ESCAPE FROM THE
HELICOPTER MUST BE THOROUGHLY PRACTICED BY THE PILOT
ON THE GROUND TO ENHANCE HIS SAFETY IF EMERGENCY
ESCAPE FROM THE COCKPIT SHOULD BE NECESSARY.
6.2.24 Transfer the night-vision goggles to the stowed position as
instructed in Step 6.2.10 of this Manual.
6.2.25 Take out the used batteries from the night-vision goggles.
6.2.26 Take off the helmet and detach counterweight (9).
6.2.27 Place the night-vision goggles into the case and put the
counterweight into the outer pocket.
6.2.28 Discharge the rechargeable batteries, if any, and recharge
them, using a standard charging unit designed for charging the
rechargeable batteries of type size AA 1.5 V in accordance with the
Manual furnished with the unit.
6.2.29 Place the batteries (including rechargeable batteries) into
the inner pocket of the case.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 31
NVS 6
MANUAL
6.3 Arrangement of Night-Vision Goggles on Helicopter (Figs
6.4 thru 6.7)
6.3.1 Remove the following components from the case (Ref. Fig.
3.1): night-vision goggles (1), batteries (6) (2 pcs), mount (7), counterweight
(10), voltage converter (2) complete with LVC (low-voltage converter) (10)
(Ref. Fig. 5.1), and cable (11).
6.3.2 Secure LVC (19) (Ref. Fig. 6.7) in the place allotted for it in
the cockpit and connects it to the helicopter electrical system by making
use of airborne power cable (21) (engage receptacle (22) with LVC
plug (23)).
6.3.3 Attach cable (20) with the aid of spring clamps (24) in the
cockpit.
6.3.4 Install mount (26) found in the single set of spare parts (Ref.
Fig. 6.6, Step 6.2.11) onto the front portion of the helmet.
6.3.5 Install counterweight (9) (Ref. Fig. 6.5, Step 6.2.12) onto the
rear portion of the helmet.
6.3.6 Insert batteries into the special recess on the night-vision
goggles (Ref. Step 6.2.5 of this Manual) to ensure independent power
supply of the goggles.
6.3.7 Install the night-vision goggles on the helmet (with the helmet
removed from the head) in the stowed position (Ref. Fig. 6.5), for this
purpose; join the fixing assembly of the night-vision goggles to mount (26)
of the helmet (Ref. Fig. 6.6). Using extreme care, insert the fixing
assembly plate of the night-vision goggles into the slots of guide (12) of
helmet mount (26) avoiding misalignment and shift the plate upwards until
retainers (13) become latched.
Prior to installation, the night-vision goggles shall be adjusted to fit
the eyes of a pilot as instructed in Section 6.2 of this Manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 32
NVS 6
MANUAL
6.3.8 Fasten cable (14) on counterweight (9) using strap (10) (Ref.
Fig. 6.5, Step 6.2.15).
6.3.9 With the goggles placed in the stowed position secure helmet
soundly on the pilot’s head.
6.3.10 Connect cable (14) to cable (20) with the use of the connector
(25) (Ref. Fig. 6.7).
6.3.11 Turn on the switch to apply the helicopter electrical power to
the night-vision goggles.
6.3.12 Depress button (1) (Ref. Figs 6.4, 6.5) and, while holding the
fixing assembly with one hand and taking hold of the monocular pair with
the other hand, transfer the goggles to the operating position so that the
fixing assembly becomes straightened. In doing so, see to it that only
slight effort is applied for ensuring proper locking (latching) of the
monocular pair in the operating position. Only an effort sufficient to cause
operation of retainer (21) is necessary. (Ref. Fig. 5.2). The goggles will
get energized.
This done, the pilot shall see amber-green illumination free from
flashes and twinkling on the screens of both channels of the night-vision
goggles, which is indicative of normal operation of the goggles powered
from the helicopter electrical system.
Note – When the night-vision goggles are powered from the
helicopter electrical system, they are energized and de-energized
automatically in response to their transfer from the stowed to the
operating position and vice versa irrespective of the position of cap (6) (Ref.
Fig. 6.4) of cap-switch (5).
CAUTION: 1 WHEN THE NIGHT-VISION GOGGLES ARE
SWITCHED ON IN THE PRESENCE OF LIGHT OR WITH THE WHITE
FLOOD LIGHT TURNED ON, MAKE ABSOLUTELY SURE THAT THE
SAFETY CAPS ARE FITTED ON THE LENSES TO PREVENT DAMAGE
OF THE UNIT.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 33
NVS 6
MANUAL
2 IF THE POWER SUPPLY OF THE GOGGLES FROM THE
HELICOPTER ELECTRICAL SYSTEM IS NOT AVAILABLE, THEIR
OPERATION MAY BE PROVIDED FROM THE INDEPENDENT BUILT-IN
POWER SOURCE (TWO BATTERIES AA R6 1.5 V OR
RECHARGEABLE BATTERIES OF A SIMILAR TYPE).
6.3.13 If the alignment of the monoculars of the night-vision
goggles with respect to the eyes of the pilot is not accurate enough and
the monocular pair is not adjusted to suit individual features of his
eyesight, perform the adjustment operations as prescribed by Steps 6.2.19,
6.2.20 of this Manual.
Now the goggles are ready for work.
Upon completion of work with the goggles, carry out the following
operations:
6.3.14 Take hold of the monocular pair with one hand and the fixing
assembly with the other hand and transfer the night-vision goggles to the
stowed position (i.e. "fold up" the fixing assembly by overcoming the force of
the retainer which locks the goggles in the operating position).
6.3.15 Turn off the switch used for supplying power from the
helicopter electrical system to the night-vision goggles.
6.3.16 Disconnect cable (14) (Ref. Fig. 6.7) from cable (20) by
disengaging the connector (25).
6.3.17 Take off the helmet complete with the night-vision goggles
installed and detach the counterweight from the helmet.
6.3.18 Remove the night-vision goggles from the helmet by pulling
them down by hand, having pressed levers (18) (Ref. Fig. 6.4) to disengage
the goggles fixing assembly plate from the guides of mount (26) of the helmet.
6.3.19 Remove screws (27) and remove mount (26) from the helmet.
6.3.20 Remove the used batteries from the night-vision goggles.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 34
NVS 6
MANUAL
6.3.21 Disconnect power cable (21) (Ref. Fig. 6.7) of the helicopter
electrical system from the LVC (low-voltage converter), and disengage
cable receptacle (22) from plug (23) of the LVC.
6.3.22 Remove the LVC (complete with cable (20)).
6.3.23 Put the night-vision goggles into the case. Do not put the
rechargeable batteries into the case.
6.3.24 Discharge and recharge the rechargeable batteries in
conformity with the Instructions presented in the Manual furnished with
the standard battery-charging unit.
6.3.25 Pack the batteries and the rechargeable batteries after being
charged into the case.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 35
NVS 6
MANUAL
7 OPERATION PROCEDURE
7.1 The conditions in which the night-vision goggles are operated
have their own idiosyncrasy, which requires certain skills on the part of
the pilot as the image of the terrain and objects visible through the night-
vision goggles is monochromic and not very soft.
7.2 The night-vision goggles enable the pilot not only to nap off the
earth but also view the instrument panel by taking a look downwards or
sideways past the eyepieces.
CAUTION: WHEN THE NVS 6 IS USED AT NIGHT TIME, THE
SAFETY CAPS SHALL BE REMOVED FROM THE LENSES.
7.3 For removing the safety caps, press simultaneously on both
retainers and, while holding them depressed, take the cap off of the lens
mount. Put the removed caps into the case pocket.
7.4 After removing the safety caps, focus the lenses of each
monocular by rotating the lens about its optical axis so as to attain the
sharp image of the viewed objects in the space outside the cockpit (for
convenience of rotation each lens is provided with knurling).
7.5 In case that the airborne power supply is not available, turn on
the independent power source to feed power to the night-vision goggles
by turning cap (6) of cap-switch (5) (Ref. Fig. 6.4).
7.6 If the night-vision goggles become exposed to bright light, turn
your head to divert the lenses sideways so as to bring the image of bright
light sources outside the field of view.
7.7 In the event of fogging of the eyepieces of the night-vision
goggles (low temperature), pull the goggles out of the operating position
and wipe dry the external surfaces of the eyepieces with a cloth included
in the single set of spare parts.
7.8 After long usage of the night-vision goggles on the pilot’s head
(more than 2.5 h), the pilot may feel a light fatigue in the neck muscles.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 36
NVS 6
MANUAL
7.9 Upon completion of work with the night-vision goggles and after
the helicopter landing, perform the operations prescribed by Steps 6.2.14
thru 6.2.25. If need be, clean the night-vision goggles and their
accessories from dust, dirt and traces of moisture with the cloth included
in the single set of spare parts.
7.10 The preparation of the night-vision goggles for the next flight
consists in replacement of the rechargeable batteries used in flight with
newly charged ones and accomplishment of operations in accordance with
Table 5.
7.11 Prior to an emergency evacuation of the helicopter, depress
levers (18) (Ref. Fig. 6.4) of the fixing assembly with the left (right) hand
thumb and forefinger and promptly pull the night-vision goggles down. As
the goggles become disengaged from the guide on the helmet, keep on
moving your hand to the left or right side until the power cable gets
disconnected from the helmet.
The subsequent operations shall be carried out in compliance with
the "Helicopter Crew Instructions" that specify the procedures for the night-
vision goggles usage during flights.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 37
NVS 6
MANUAL
8 OPERATIONAL STATUS CHECK
8.1 In the course of the NVS 6 service, it is essential to continually
carry out its inspection. The inspection shall be accomplished during all
kinds of maintenance checks with the aim of determining the unit
operational status, and detecting in due time its defects and their
correction. The operational status of the unit is exemplified by its
serviceability, completeness of its standard set, and readiness for use.
8.2 The list of the basic checks of the NVS 6 and its accessories
for operational status (inspection procedures) is presented in Table 3.
Table 3
Procedure
Inspection method
Technical requirements
1 Unit standard
set inspection for
full complement
Check the standard
delivery set against
The unit standard set
shall comply with the
the list of the unit com- standard delivery set
ponents in the Log
Book.
specified in the NVS 6 Log
Book.
2 External
inspection of
the unit and its
accessories
Inspect the unit for
The external surfaces of
external condition (vi- the unit and its accessories
sually).
shall not be affected by
cracks, dents, traces of cor-
rosion and other defects.
The lenses and
eyepieces shall be free
from cracks, spots of
grease and dirt.
3 Serviceability
The procedure for
With the unit energized
test of the unit and serviceability test is
its accessories
(either from the helicopter
described in Section 6 electrical system via the
of this Manual. voltage converter, or from
Table 3, cont'd
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 38
NVS 6
MANUAL
Procedure
Inspection method
Technical requirements
IPS), the image-intensifier
tube screens shall
illuminate and, after dioptric
adjustment of
the eyepieces (Ref. Step
6.2.20) and focusing of the
lenses (Ref. Step 7.4),
nearby objects shall be
clearly seen in the unit field
of view.
4 Quality of
image viewed by
unit
The check is
The unit shall provide for
conducted by the pilot distinct identification of the
in the course of test pattern lines in all four
individual adjustment directions and easy reading
of the night-vision
goggles (Ref. Step
6.2.21)
of the check text, which is
indicative of the fact that
the unit is ready for use.
9 TROUBLE SHOOTING
9.1 Normal operation of the NVS 6 is substantiated by the following
indications:
(a) Feasibility of observing the illumination of the screens (without
flashes and twinkling) of each of the two image-intensifier tubes through
the eyepieces.
(b) Clear visibility of nearby objects and the test pattern lines in
the course of preflight preparation.
9.2 All these signs are indicative of the adequate operational status
of the NVS 6 for ensuring its normal functioning.
9.3 The list of the most frequent and probable troubles of the NVS
6 is given in Table 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 39
NVS 6
MANUAL
Table 4
Trouble
and
symptoms
Probable
cause
Correction
Remarks
1 NVS 6 failure
to operate
1 Polarity of
connected
1 Remove
Can be
rechargeable
performed in
(image-intensifier rechargeable batteries and then the field
tube screens are batteries is not fit them in so that
not illuminated)
observed
the positive lead
marked with "+" is
directed inwards
into guide (2) (Ref.
Fig. 5.2)
2
1 Charge
Can be
Rechargeable rechargeable
performed in
batteries
batteries on the bat- the field
(batteries) are tery charging unit
discharged or as instructed in the
unserviceable Manual furnished
with
Trouble
and
symptoms
Probable
Remedy
cause
Remarks
The unit, or replace
failed rechargeable
batteries or batteries
with serviceable
ones included in
the single set of
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 40
NVS 6
MANUAL
Trouble
and
symptoms
Probable
cause
Remedy
spare parts
Remarks
3 Presence
of moisture
1 Replace dehyd-
rator cartridge (13)
Can be
performed in
the field
inside the unit (Ref. Fig. 5.1), by
first inspecting the
color of silica gel
indicator through
sight glass (14).
Replace the silica
gel, when its color is
turned lilac or rosy
4 LVC or
1 Forward the unit
To be
cable are out for repair
of order
performed at a
repair shop or
at Manu-
facturer’s
facilities
5 Image-
1 Forward the unit
To be
intensifier tube for repair
is out of order
performed at a
repair shop or
at Manu-
facturer’s
facilities
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Trouble
and
symptoms
Probable
cause
Remedy
Remarks
Can be
2 Image of
1 Dirt on
1 Wipe clean
viewed objects is external
external surfaces of performed in
lens (1) (Ref. Fig. 5.1) the field
not sufficiently
sharp
surfaces of
the unit lens, and eyepiece (2)
eyepiece
with cloth (11) (Ref.
Fig. 3.1) included in
the single set of
spare parts
2 Unit is out
1 Adjust properly
Can be
of focus
(dioptric
setting of
sharpness of image performed in
by rotating eyepiece the field
(2) (Ref. Fig. 5.1)
eyepieces has with the aid of
not been
adjustment ring (3).
performed,
lenses have
not been
2 Bring the image
viewed in lenses (1)
(Ref. Fig. 5.1) into
sharp focus as
instructed in Step
7.4
focused)
3 Lens or
1 Forward
the unit for
repair
To be
eyepiece is af-
fected by phy-
performed at a
repair shop or
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 42
NVS 6
MANUAL
Trouble
and
symptoms
Probable
cause
Remedy
Remarks
at Manu-
sical damage
repair
facturer’s
facilities
1 The
1 Forward the unit
To be
image-
for repair
performed at a
repair shop or
at Manu-
3 One of the
intensifier tube
is unser-
image-intensifier
tube screens is
not illuminated.
viceable
facturer’s
facilities
Visible on the
screen are black
dots that tend to
grow to a
dimension of a
segment
4 With the unit
1 Moisture
1 Replace
Can be
energized, drops has got inside dehydrator cartridge performed in
of moisture are the unit (failure (13) (Ref. Fig. 5.1), the field
visible on optical of the eye- by first inspecting
surfaces in the
field of vision of
the eyepiece
piece sealing) the color of silica gel
indicator through
the sight glass (14).
Replace silica gel
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Trouble
and
symptoms
Probable
cause
Remedy
Remarks
when its color has
changed to lilac or
rosy
5 Night-vision
1 Fixing
1 Forward the unit
for repair
To be
goggles are not assembly of
properly secured the night-visi-
on the mount of on goggles is
performed at a
repair shop or
at Manu-
the helmet
out of order
facturer’s
facilities
Page 44
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
10 MAINTENANCE PRACTICES
10.1 The maintenance operations to be carried out on the NVS 6
constitute the essential part of the unit operation and their correct
performance can significantly prolong the unit service life and keep it
always ready for use.
10.2 For maintaining the NVS 6 at constant readiness for service,
provision is made for the following line maintenance procedures (preflight
checks):
(1) Preliminary preparation.
(2) Preflight preparation.
(3) Preparation for the next flight.
(4) Post flight procedures.
10.3 The maintenance operations and checks stipulated by the
above maintenance practices are presented in Table 5.
Table 5
Line maintenance procedures
(preflight checks)
Subject of maintenance
and operations
Prelimi-
nary
preparat
ion
Prepara- Post-
Preflight
prepara-
tion
tion for
next
flight
proced
ures
flight
1 Storage battery charging in
accordance with the Manual
furnished with the battery charging
unit (in using rechargeable
batteries) or replacement of
batteries
+
–
–
–
2 Cleaning external surfaces of
the lens and eyepiece in
+
–
–
–
compliance with the procedure
prescribed by this Manual
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Table 5, cont'd
Line maintenance procedures
(preflight checks)
Subject of maintenance
and operations
Prelimi-
nary
preparat
ion
Prepara- Post-
Preflight
prepara-
tion
tion for
next
flight
proced
ures
flight
3 Inspection:
Inspection of the night-vision
goggles and their accessories for
external condition as instructed in
Section 8:
+
+
+
+
Checking the unit set for
completeness
+
+
–
+
–
+
+
+
Checking the night-vision
goggles and their accessories for
external condition
Testing the night-vision goggles
for serviceability
+
+
+
–
+
–
+
–
Checking the night-vision
goggles for image quality
4 Preparation of the unit for
use in compliance with Section 6:
Individual adjustment and fitting
of the unit
+
–
–
+
–
–
–
–
Arrangement of the night-vision
goggles on the helicopter
5 Concluding operations on
the unit as per Sections 6, 7
+
–
–
+
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 46
NVS 6
MANUAL
10.3.1 For cleaning the outer surfaces of the lenses and eyepieces,
wipe them with a clean cloth included in the single set of spare parts, by
first blowing off grains of sand and dust from the surfaces.
In case of severe contamination of the optical parts, do their
cleaning as follows:
– Obtain a Q-tip (used for ears cleaning). If not available, wind
a small amount of cotton wool around the end of a wooden stick, after
having sharpened the stick end
– Moisten the cotton wool (or Q-tip) with alcohol or ether, or their
mixture and then shake the stick to remove excess of liquid;
– Wipe the glass with the cotton wool (or Q-tip) several times
without touching the eyepieces with hands
– Replace the cotton wool (or Q-tip) with a dry one and perform
circular strokes with the cotton wool moving it from the center to the edge to
finish the cleaning.
It should be remembered that the unit should be de-energized
during the process of optical surfaces cleaning. Perform cleaning of the
monocular pair, fixing assembly and unit accessories to remove dust, dirt,
etc. (if any).
10.4 In the course of service and storage of the NVS 6, it is
necessary to ensure replacement of the independent power source.
10.4.1 The rechargeable batteries shall be replaced on expiration
of the guarantee period of their service life, whereas the batteries shall be
replaced as they are run down.
10.5 The periodic maintenance checks (scheduled maintenance
procedures) meant for maintaining the unit in the serviceable condition
throughout the entire service life shall be conducted within the single time
intervals as determined by the total flying time (Ref. Table 6).
Note – Information on the service time limits and man-hours to per-
form the maintenance checks is presented in the helicopter Manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 47
NVS 6
MANUAL
Table 6
Maintenance check intervals, hours (months)
Procedure
and parameter under
check
50
100
200
(6 months)
(12 months) (24 months)
1 Cleaning lens and
eyepiece external
surfaces
+
+
+
+
+
2 Inspection:
Inspecting the night-
vision goggles and their
accessories for external
condition
+
Checking the unit set
for completeness
+
+
+
+
+
+
Testing the night-vision
goggles and their
accessories for
serviceability
Checking the night-
vision goggles for image
quality (resolving power)
+
+
+
+
+
+
3 Periodic inspection:
Checking screws for
proper tightness and
inadvertent loosening
Adjustment of retainers
force for locking in
operating position (if
required)
+
+
+
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 48
NVS 6
MANUAL
required)
10.6 The inspection procedure shall be performed as specified in
Table 3.
10.7 The image quality shall be tested in compliance with Step 6.2.21.
10.8 The screws shall be checked for proper tightness, slipping and
inadvertent loosening with the aid of the screwdriver, included in the set of
spare parts.
When carrying out this check, make sure that the screws
completely secure the joints between parts and assemblies. Screw
slippage and loosening are inadvisable.
10.9 The adjustment of force of retainer (21) (Ref. Fig. 5.2) shall be
accomplished by turning the retainer attachment screw.
When the screw is turned, the retaining force changes (retainer
spring pressing force).
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 49
NVS 6
MANUAL
11 STORAGE AND SHIPMENT
11.1 The NVS 6 units should be stored in heated premises at
a temperature of +5 to +40 oC and a relative air humidity of not in excess
of 80 %.
11.2 Maintenance of the units, while at store, shall be performed as
instructed in Section 10 of this Manual.
11.3 Perform preservation of the unit before placing it for prolonged
storage. The preservation is done by the use of lamination method
(the units are sealed in a polyethylene bags).
On the expiry of three years since preservation, the unit shall be
subject to repeated preservation.
11.4 The NVS 6 can be shipped by any type of transport and over
varied distances, provided proper packaging is in place.
During transportation the package that contains the case with
the unit shall be securely protected against shocks and dropping.
The case shall be placed in the package with the top cover directed
upwards and carefully fastened.
CAUTION: AVOID DROPPING THE PACKAGE WITH THE UNIT
DURING LOADING AND UNLOADING OPERATIONS.
Page 50
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
APPENDIX A
List of Illustrations
(reference)
Fig.
Title
Page
3.1 NVS 6 Standard Set
5.1 NVS 6
6
9
5.2 Night-Vision Goggles
5.3 Low-Voltage Converter
5.4 Mount
11
15
17
20
21
21
24
6.1 Replacement of Casing on Helmet
6.2 Assembly of Clamp with Retainer
6.3
6.4 Installation of Night-Vision Goggles on Helmet in
Operating Position
6.5 Night-Vision Goggles Installed on Helmet in Stowed
Position
25
26
27
6.6 Installation of Night-Vision Goggles on Helmet and Their
Adjustment Relative to Pilot’s Eyes
6.7 Connection of Night-Vision Goggles to Helicopter
Electrical System Via Voltage Converter
Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
List of Abbreviations
(reference)
FOV – Field of view
IPS – Independent power source
LVC – Low-voltage converter
Page 52
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
WARRANTY:
NEWCON OPTIK warrants this product against defects in material and
workmanship for one year from the date of the original date of consumer's
purchase, but no more than 18 months from the date of manufacturing. Should
your Newcon product prove defective during this period, please bring the product
securely packaged in its original container or an equivalent, along with proof of
the date of original purchase, to your Newcon Dealer. Newcon will, replace or
repair (or at its option replace), the product or part thereof, which, on inspection
by Newcon, is found to be defective in materials or workmanship.
What This Warranty Does Not Cover:
NEWCON is not responsible for warranty service should the product fail to be
properly maintained or fail to function properly as a result of misuse, abuse,
improper installation, neglect, damage caused by disasters such as fire, flood,
lightning, improper electrical current, or service other than by a NEWCON
Authorized Service. Postage, insurance, or shipping costs incurred in presenting
your NEWCON product for warranty service are your responsibility. Please
include a cheque or money order made out to NEWCON OPTIK for the amount
of $15.00 to cover shipping and handling within Canada or the U.S.A. Shipping
to other destinations will be done at the customer’s expense.
8. Customer Support
Should you experience any difficulties with your Newcon OPTIK product, consult
the enclosed manual. If the problem remains unresolved, contact our customer
support department at (416) 663-6963 or Toll free at 1-877-398-6666. Our
operating hours are 9am-5pm, Monday - Friday, standard East time. At no time
should equipment be sent back to Newcon without following the instructions of
our technical support department.
Newcon accepts no responsibility for unauthorized returns.
To locate the NEWCON Authorized Dealer call:
Tel: (416) 663-6963 Fax: (416) 663-9065
Email: [email protected]
INTERNET: http://WWW.NEWCON-OPTIK.COM
The defective products should be shipped to:
In USA: 3310 Prospect Ave. Cleveland, OH 44115
From other countries : 1183 Finch Ave. W., Suite 302, Toronto, ON M3J 2G2
Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
NVS 6
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 54
|