Navman
8120/8084
Fuel, AIS, & Radar
Addendum 06/07
Download from Www.Somanuals.com. All Mwanuawls Swearc.hnAndaDovwnmloada. n . c o m
Fuel functions and display
What the fuel computer does
!
WARNING
To ensure the fuel data is accurate:
When you add or remove fuel from a tank, tell the 8120/8084.
If the boat has petrol/gasoline sensors, calibrate them during installation or if the fuel
readings seem inaccurate.
Choose an appropriate type of boat speed sensor or GPS source to calculate economy,
range and the fuel consumption curve.
If the boat uses a paddlewheel sensor to measure speed, calibrate it during installation or
if the speed readings seem inaccurate.
Low fuel alarm
To set a low fuel alarm for a tank:
When a low fuel alarm is set, the alarm’s fuel
level is shown on the fuel display tank levels
as a red bar. The alarm can also be set using
the Alarms setup menu.
1
2
3
Press
Setup tanks.
twice, select Fuel,then select
On a multi-tank boat, select the tank to set
the alarm for.
Select Tank alarmand enter a fuel level
to trigger the low fuel alarm; or enter zero
to disable the alarm.
Boat speed sensors
To select an optional speed sensor
Selecting a boat speed sensor
1
Press
twice, select Fuel,then select
The fuel calculations can use boat speeds
from the GPS, or from a paddlewheel sensor
or pitot sensor if these optional sensors are
installed:
Speed source.
2
To use a paddlewheel or pitot sensor,
select Water speed, otherwise select
Ground speedto use GPS speed.
Paddlewheel and pitot sensors measure
the speed through the water; GPS speed is
speed over ground; these sensors can give
different values for Range, Economy and
the fuel consumption curves.
3
i
If you selected Water speed and you have
both a paddlewheel sensor and a pitot
sensor:
Press
, select SmartCraftand
A pitot sensor is more accurate than a
paddlewheel sensor at high speeds but is
not accurate at low speeds. A paddlewheel
sensor is more accurate than a pitot sensor
at low speeds.
select Speed type
ii Select Paddlewheelor Pitot.
Tip: You can select a different speed
sensor during a trip.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Water speed is better for measuring the
boat’s potential performance, Ground speed
is better for going to a destination because it
takes currents into account.
Water speed and ground speed
A paddlewheel sensor and a pitot sensor
measure water speed, the boat speed
through the water. A GPS measures ground
speed, the boat speed over the bottom of
the water. If there is a current, then these
speeds will be different, and the log, trip
log, economy and range will be different, as
shown below.
When the current is from ahead, ground speed is less than water speed
Water speed 10 knots Water speed 10 knots
Current 4 knots
Gives a ground speed of 6 knots
Gives a ground speed
of about 8 knots
Current 4 knots at 45º
For this example:
If the boat travels for one hour, uses 3 gallons of fuel per hour and has 50
gallons of fuel left:
Speed
Using water speed: 10 knots 10 nm
Using ground speed: 6 knots 6 nm
Log
Economy
Range
3.3 nm / gal 165 nm
2.0 nm / gal 100 nm
When the current is from behind, ground speed is more than water speed
Water speed 10 knots
Current 4
knots at 45º
Current
4 knots
Water speed 10 knots
Gives a ground speed of 14 knots
For this example:
Gives a ground speed of about 13 knots
If the boat travels for one hour, uses 3 gallons of fuel and has 50 gallons of fuel left:
Speed Log Economy Range
Using water speed: 10 knots 10 nm
Using ground speed: 14 knots 14 nm
3.3 nm / gal 165 nm
4.7 nm / gal 235 nm
4
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibration
Calibrate petrol/gasoline fuel flow
To calibrate the sensor(s):
sensors during installation, or if the fuel
readings seem inaccurate and the other
troubleshooting suggestions do not help.
1
2
Record the level of the fuel in the tank(s).
Connect the portable tank(s) to the engine
through the fuel sensor(s).
Note
3
4
Run the engine at normal cruising speed
until at least 4 gallons (15 litres) of fuel has
been used per engine.
SmartCraft fuel sensors and NAVMAN
diesel sensors are factory calibrated and
should never need recalibrating.
Check the actual amount of fuel used per
engine by refilling the portable tank(s) to
the original level and noting the reading(s)
of the fuel dispenser’s gauge.
On a multi engine boat, calibrate each
engine’s sensor. This can be done at the
same time with a portable tank for each
engine or at different times using one
portable tank.
5
6
Press
twice, select Fuel,then select
Setup engines.
Calibrating a sensor requires accurate
measurement of the fuel consumption.
This is best done using a small portable
tank. At least 4 gallons (15 litres) of fuel
should be used to ensure an accurate
calibration.
On a single engine boat, select
Calibrateand change the displayed
value to be equal to the reading of the fuel
dispenser’s gauge, then press
.
On a multi-engine boat select the engine.
Select Calibrateand change the
displayed value to be equal to the reading
of the fuel dispenser’s gauge, then press
. Repeat for the other engines.
It is often very difficult to fill underfloor
tanks to the same level twice due to air
pockets, so the more fuel used, the more
accurate the calibration.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AIS
AIS is short for Automatic Identification
System. The International Convention
for Safety of Life At Sea (SOLAS) requires
all vessels greater than 300 tons and all
passenger vessels to be equipped with AIS
Transponders. All vessels equipped with
AIS permanently broadcast via one or more
of the two dedicated VHF channels. This
transmission may include information about
the vessels MMSI-number, its call sign, name,
position, course, heading, speed, rate of turn
and type of vessel.
the local area are shown on the chart when
this feature is enabled.
The following AIS receivers are supported by
this unit:
•
•
Comar SLR200 (external GPS).
Weatherdock Two Channel AIS Receiver
“EASY AIS”, Part No. 5-A-013 (external GPS).
•
NASA Marine AIS Engine 2 channel
MultiPlex Receiver (external GPS).
Other AIS receivers may work but have not
been tested with this unit.
This unit can receive and display AIS
information when connected to an AIS
receiver. Available AIS vessels transmitting in
To enable AIS from the system menu check
the AIS box.
Viewing AIS Vessels
A typical AIS window shows:
E
B
A
C
A AIS Vessel
B Dangerous Vessel
C Projected Course
D Data Box
E
Range Rings
6
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
When the cursor is placed over an AIS
vessel for at least two seconds, a data box
appears at the bottom of the window with
information about the AIS vessel.
For complete AIS information of the AIS
vessel place the cursor over an AIS vessel for
at least two seconds and press
.
Press either
information.
or
to clear the
Dangerous Vessels
The 8120/8084 calculates the time of closest
point of approach (TCPA) and closest point of
approach (CPA) for each AIS vessel.
TCPA 15 min
This is used to determine potential dangerous
vessels. If the TCPA and the CPA is below
the trigger values then it will be considered
dangerous.
CPA 0.5 nm
A dangerous vessel is indicated on the chart
by a red circle around the icon.
AIS Windows
Vessels
To go to the AIS windows, press
, select
More, select AIS, then press or to select
one of the two windows: Vessels or Safety
msgs (rx).
This is a sorted list of vessels currently being
received by the AIS receiver. The maximum
number of vessels that the system will
support is 250. Once maximum is reached,
vessels furthest away from the current
location will be replaced. A vessel will be
removed from the list if no information is
received within 6 minutes from the last
message.
If there are more items than will fit on the
window, press or to see the others.
Displaying an AIS vessel on the chart
1
Press or to select a vessel.
2
Press and select Display. The
Instrument switches to chart window, with
the selected vessel position in the middle.
Displaying Full AIS Details
1
Press or to select a vessel.
2
Press
press
and select More Infoor
.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Full AIS Details
Filter by Type
1
Press or to select a vessel.
Vessel types that are not selected will be
filtered off the chart. Default is set to all types
enabled allowing all vessels to be displayed
on the chart.
2
Press
press
and select More Infoor
.
This window displays all information for
the selected AIS vessel provided by the AIS
receiver.
Filter by distance
Vessels outside the radius selected from our
current position are filtered off the chart.
Default value is set to 300 nm allowing all
vessels to be displayed on the chart within
that distance.
Sorting Vessels
Press
, select Sortand select one of
the options.
This sorts the list based on the chosen
category.
Filter by speed
Vessels with speed below the value selected
are filtered off the charts. Default is set to 0
nm allowing all vessels to be displayed onto
the chart.
Safety msgs (rx)
Safety msgs (rx) are broadcasted messages
received by the AIS receiver. This window
displays the date and time of message
received, MMSI of AIS vessel that broadcasted
the message, and the message itself. Safety
msgs (rx) list will store up to 10 messages.
The oldest message is replaced when the list
is full.
Show Dangerous Only
Show only vessels that have a TCPA/CPA
below the trigger values. This filter will
override any other filter option.
Dangerous Vessel Alarm
When enabled an alarm will activate when
both the TCPA and CPA are less than the
trigger values.
Note: Even when this setting is disabled the
dangerous vessels will still be indicated on
the chart.
TCPA Limit
Set the Time of Closet Point of Approach
limit.
CPA Limit
Set the Closet Point of Approach limit.
Note: This feature requires an AIS receiver.
Projected Course
Show the estimated course of all vessels
based on their current SOG and COG.
There are multiple methods to filter AIS
vessels that are displayed onto the charts.
Range Rings
Show a selectable number of range rings
around the boat. The rings are drawn in
multiples of the current chart scale.
Proximity Alarm
When enabled an alarm will activate when
any AIS vessel is within the proximity alarm
radius.
8
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Radar is the Radio Detection And Ranging
system. Radar functions require an optional
NAVMAN radar system to be installed. Three
radar systems are available; 2 kW, 4 kW, or
6 kW.
The scanner rotates through 360° so the
radar window shows all of the area around
your boat within the range of the scanner,
producing a map-like display called the PPI
(Plan Position Indicator).
When the radar is operating, the scanner
transmits powerful microwave radio pulses
which are reflected back from any solid
objects such as land masses or other boats.
These objects are called targets and are
shown on the radar window.
Typically, your boat is in the centre of the
radar window with concentric range rings
surrounding it. The range rings help you
to quickly estimate the distance to various
targets.
You can also view the radar overlaid on the
chart screen.
Radar window
A
B
C
K
L
I
J
M
D
H
G
E
F
The radar window shows:
G Compass ring
A Distance between each range ring (in this
H Range ring
example, 1/8 nautical mile)
I
North line (blue)
B Range of radar (in this example, shown in
J
Heading line (white)
large digits)
K The bearing (in Relative, True, or Magnetic
C Radar rotation (in this example, North Up)
mode)
D Radar motion mode (in this example,
L
Echo Expansion setting
Relative Mode)
M Interference Rejection setting
E
F
Cursor
Distance and bearing to the cursor from
the vessel position
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar modes
There are four radar modes:
•
•
Standby. The radar is on and is warmed
up. It is ready to start transmitting
immediately.
•
Disabled. This saves on power
consumption and magnetron usage. If the
radar is disabled, it has to warm up and
enter standby mode before it can start
transmitting.
Transmitting. The radar is actively sending
and receiving microwave radio pulses. An
open array will be rotating.
•
Warming. The radar on and is warming up.
This can take up to 90 seconds, depending
on your scanner type.
If you want to save on power but be able to
start transmitting immediately, use standby
mode.
Enabling the radar functionality
When the radar is enabled, it will turn on,
warm up, and enter standby mode.
3
4
The radar immediately turns on and enters
warm-up mode. A message shows how
long this will take.
To enable the radar functionality:
When the warm-up period is complete,
the radar enters standby mode and is
ready to transmit.
1
Press
menu, then select System.
Set Radar to
twice to display the Setup
2
.
Selecting standby mode or transmit mode
You can quickly change between these two
modes.
set the Transmit option to (transmit
mode) or (standby mode).
1. From the radar window, press
and
Disabling the radar functionality
sure that you want to disable the radar
functionality, select Yes.
The radar enters disabled mode
immediately.
1
Press
menu, then select System.
Set Radar to
A warning message appears. If you are
twice to display the Setup
4
2
3
.
Radar Chart Overlay
If you have a radar installed, you can overlay
the radar screen on your chart screen. This is
extremely useful because it can help you to:
To turn the radar overlay on or off:
From the chart window, press
and set
Radar Overlay option to or
.
•
interpret the radar image by matching the
radar targets with charted objects
An extra menu item will them be displayed to
control the radar and overlay.
•
quickly identify objects that are not on the
chart, such as other boats
Overlay Palette
The color of the radar overlay can be
changed, to improve chart/ radar data
The radar overlay is also very useful in
conditions of reduced visibility, at night, or in
busy or hazardous waters.
10
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
separation or take into account viewing
conditions.
2
Select Radar overlay. If the box is
ENTER
unchecked, press
. A Radar menu
option appears below.
MENU
1
2
3
4
Press
twice.
3
4
5
Select Radar.
Select Transparency.
Adjust the slider to suit. Changes are seen
on the chart in real time.
Select Radar.
Select Overlay palette.
Select your color preference.
Overlay Transparency
The transparency of the radar overlay can be
adjusted, in case it obscures important chart
Also available on the Radar overlay
menu are shortcuts to enable/disable radar
transmission (Transmit, see Manual,
18-4) and to access the radar setup options
(Adjust radar, see manual, 18-6).
features.
MENU
1
From the chart screen or pane, press
once.
Adjusting the quality of the radar window
Common problems that can degrade the
quality of the radar window include:
Changing the gain mode
•
•
•
sea clutter
rain clutter
false echoes (sometimes called ghost
echoes) and background noise
•
side lobe patterns (false echoes that appear
as an arc or a broken arc)
•
•
•
shadows (blind spots)
multiple echoes off the same object
incorrect threshold setting
Use the radar gain mode to specify whether
you want to adjust the radar gain yourself or
have it adjusted automatically.
If the radar is installed at a suitable height and
in a suitable location on your boat, side lobe
patterns and shadows (blind spots) caused
by obstructions such as funnels or masts will
be minimized. If you are having problems
with these, you may need to relocate the
scanner. Consult the Installation Guide for
your NAVMAN scanner or talk to your dealer or
installer.
To change the radar gain mode:
1
From the radar window, press
then
select Adjust Radar.
2
Select Gain Mode. There are three
choices:
•
Manual. Adjust the radar gain yourself
to suit your local conditions and
preferences.
Multiple echoes off the same object are
most likely to occur when you are close to a
large target and are usually only a temporary
nuisance.
•
•
Auto. The radar gain is adjusted
automatically.
Range rider. Select this to adjust the
radar gain yourself for a particular radar
range, then have these settings stored
and automatically re-used whenever
you operate at that range again.
You can adjust the radar to reduce the effects
of sea clutter, rain clutter, and interference
from other radars. You can also change the
gain mode setting and the gain level setting to
help reduce false echoes.
From the radar window, press
then
select Adjust Radarand press
.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the gain level
Changing the sea clutter level
Use the radar gain level to adjust the sensitivity
of the radar receiver. Ideally, the radar gain
level should be set so that background noise is
just visible on the radar window.
If the sea clutter level is set too low, a lot of
sea clutter will be displayed. If the sea clutter
level is set too high, small targets may not be
shown in the radar window.
If the radar gain level is too low, weak echoes
won’t be shown. If the radar gain level is too
high, strong echoes will be difficult to see
amongst the large amount of background
noise.
If the sea clutter mode is set to Harbour or
Offshore, and you adjust the sea clutter level
manually, the sea clutter mode changes to
Manual.
To change the sea clutter level:
(If the radar Gain Mode is set to Auto and you
adjust the gain level manually, the Gain Mode
is changed to Manual.)
1
From the radar window, press
select Adjust Radar.
Select Sea Clutter Level then
then
2
To change the radar gain level:
use and
to decrease or increase the
1
From the radar window, press
then
setting.
select Adjust Radar.
Select Gain Levelthen use and
to decrease or increase the setting.
Changing the rain clutter
2
Rain clutter consists of random dots that can
merge into badly-defined echoes on your
radar screen.
Changing the sea clutter mode (Manual
mode)
Sea clutter usually appears as confusing,
random signals close to your boat on the
radar window.
The random signals are returned from
rain, hail, sleet, or snow and can result in a
confusing display.
If the rain clutter is set too low, there will be
excessive rain clutter displayed whenever it’s
raining. If the rain clutter is set too high, very
large targets such as the coastline will appear
to be hollow.
High waves that can reflect the radar signal
will produce the maximum amount of sea
clutter.
You can change the sea clutter mode
yourself or have it changed automatically to
compensate for the sea conditions.
To change the rain clutter setting:
1
From the radar window, press
then
select Adjust Radar.
To change the sea clutter mode:
2
Select Rain clutterthen use and
to decrease or increase the setting.
1
From the radar window, press
select Adjust Radar.
then
2
Select Sea ClutterMode. There are
three choices:
Changing the threshold level
Use this to define the threshold level of the
weakest echo that you want to show on the
radar screen. The threshold level is shown as
a percentage.
•
•
Manual. Adjust the sea clutter setting
yourself.
Harbour. The sea clutter setting is
adjusted automatically to suit a harbour
environment.
100% is the maximum threshold level,
meaning that only the strongest echoes are
shown. 0% is the minimum threshold level,
meaning that all echoes are shown.
•
Offshore. The sea clutter setting is
adjusted automatically to suit an
offshore environment.
To change the threshold level:
1
From the radar window, press
select Thresholdthen use
then
and
to decrease or increase the setting.
12
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the echo expansion setting
If you have several small targets in view
and want to make them easier to see, use
the echo expansion option. Note that the
resolution decreases as the target size
increases, so use this option only when target
detection and visibility is more important
that the quality of the display.
To change the echo expansion setting:
From the radar window, press
then
select Echo Expansion. There are
three choices:
•
•
•
Off. No echo expansion.
1. Targets expanded x 2.
2. Targets expanded x 3.
Turning the target trails on or off
target that is moving relative to your boat will
leave a trail.
If you turn the target trails on, each target
leaves a 30 second trail on the radar screen.
You cannot change the length of the target
trail.
To change the target trails setting:
From the radar window, press
then
If you turn the target trails off, the targets do
not leave trails.
set the Target trailsoption to
(target trails are on) or (target trails are
off).
Note that if the radar motion mode is set to
true, stationary targets won’t leave a trail.
If the radar motion mode is relative, any
Using the VRM/EBL
Use one, or both of the VRM/EBL (Variable
Range Markers/Electronic Bearing Lines) to
quickly find the precise range and bearing of
a target.
The EBL is shown as a thin, dashed line
extending from the centre of the VRM to the
edge of the radar window. Use the EBL to find
the bearing of the target.
A VRM can be fixed or floating. Use the VRM
to find the range (distance) to the target.
1
From the radar window, press
select VRM/EBL.
then
•
A fixed VRM is shown as a thin, dashed,
circle centred around your boat. Use this
to find the distance of a target from your
boat.
•
You can move the centre of the VRM away
from your boat; for example, to measure
the distance between two islands. This is
called a floating VRM.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding range and bearing with a fixed
VRM/EBL
1
2
3
4
From the radar window, press
select VRM/EBL.
Select VRM/EBLthen 1 (VRM/EBL 1) or 2
(VRM/EBL 1).
then
1
From the radar window, press
then
select VRM/EBL.
Set Enable to to show the VRM and EBL
on the radar window (or to hide them).
2
3
4
Select VRM/EBLthen 1 (VRM/EBL 1) or 2
(VRM/EBL 2).
Select EBL referenceif you want to
change the EBL bearing reference. There
are two choices:
Set Enable to to show the VRM and EBL
on the radar window (or to hide them).
Select EBL reference if you want to change
the EBL bearing reference. There are two
choices:
•
°R shows the EBL bearing relative to
your boat’s head.
•
°M/°T shows the EBL bearing relative to
magnetic North or true North.
•
°R shows the EBL bearing relative to
your boat’s head.
5
Select Set centreto move the VRM
and EBL centre away from your boat. Use
the arrow keys to move the centre so that
it is aligned over the first location.
•
°M/°T shows the EBL bearing relative to
magnetic North or true North.
5
Select Adjustto adjust the VRM and the
EBL so that you can align them with the
target. Use:
6
7
Press
to save the new centre
position, then press
VRM/EBL.
and reselect the
•
and to decrease and increase the
radius of the VRM until it touches the
target to measure the range.
Select Adjustto adjust the VRM and the
EBL so that you can align them with the
second location. Use:
•
and to move the EBL until it
touches the target to measure the
bearing.
•
and to decrease and increase the
radius of the VRM until it touches the
second location to measure the range.
6
7
The range and bearing of the target is
shown at the bottom of the screen.
•
and to move the EBL until it
touches the second location to
measure the bearing.
If you want to hide (or change the settings
for) the range rings, North line, and/or
heading line, press
then select
8
9
The range and bearing of the target is
shown at the bottom of the screen.
Radar.
8
To clear the VRM/EBL display, press
and repeat steps 1 and 2. Then set Enable
If you want to hide (or change the settings
for) the range rings, North line, and/or
to
.
heading line, press
then select Radar.
If you want to find the range and bearing
of another target, repeat the sequence
using the other VRM/EBL. This is shown in a
different pattern.
10 To clear the VRM/EBL display, press
and repeat steps 1 and 2. Then set Enable
to
.
If you want to find the range and bearing
between two other locations, repeat the
sequence using the other VRM/EBL. This
is shown in a different pattern in the radar
window.
Finding range and bearing with a floating
VRM/EBL
If you move the centre of a VRM away from
your boat it is called a floating VRM. Use this
to measure the range and bearing between
two locations on the radar window, such as a
headland and a buoy.
14
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the PPI position
You can move the PPI (Plan Position Indicator)
centre to a different location if you are in
Relative motion mode. (If you are in True
motion mode, the radar automatically
positions the PPI centre.)
•
•
Look Ahead. The PPI centre is
positioned so that the radar window is
offset from the centre to give you the
maximum view ahead.
Set. Offset the PPI centre in the radar
window. (This works only when you are
using relative motion (RM) mode). Use
the arrow keys to move the PPI centre
To change the PPI position:
1
From the radar window, press
then
select Position.
to the new position then press
to
2
There are three choices:
confirm. The new position must allow
most of the radar sweep to appear
on the radar window; if it doesn’t, the
PPI centre will be moved as close as
possible to the desired position.
•
Centre. The PPI centre is in the centre
of the radar window so that all other
objects move relative to your boat.
Using the radar guard zones
You can set one or two radar guard zones
to notify you when a target enters or exits a
specified area around your boat.
Displaying the area covered by a radar
guard zone
1
From the radar window, press
then
You can customize the size and shape of the
radar guard zones and set up alarms.
select Guard Zone.
2
3
Select Zonethen radar guard
zone 1or radar guard zone 2.
Set Enable to (show the radar guard
zone) or (hide the radar guard zone).
1. From the radar window, press
then
select Guard zone.
Turning a radar guard zone on or off
Change the setting for a radar guard zone
alarm
When a radar guard zone is on, the guard
zone alarm is set automatically but you can
change the setting to suit your preferences.
1
2
3
From the radar window, press
select Guard Zone.
Select Zonethen radar guard
zone 1or radar guard zone 2.
Select Alarm preference. There are three
choices:
then
Two radar guard zones are available. You can
turn either or both on or off.
To turn a radar guard zone on or off:
1
From the radar window, press
select Guard zone.
Select Zone. There are two choices:
then
•
•
•
Enter sounds the alarm only when a
target enters the radar guard zone.
2
Exit sounds the alarm only when a
target leaves the radar guard zone.
•
•
1 selects radar guard zone 1.
2 selects radar guard zone 2.
Both sounds the alarm when a target
enters or leaves the radar guard zone.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Use and
change.
to select the parameter to
Adjusting the boundaries of a radar guard
zone
To adjust the boundaries and change the area
that is covered by a radar guard zone:
Then use and
parameter.
to change the
1
2
3
From the radar window, press
select Guard Zone.
Select Zonethen 1(radar guard zone 1)
or 2(radar guard zone 2).
Select Adjust to display the current
boundaries of that radar guard zone. The
following information is also shown in the
top left corner:
then
Adjusting the sensitivity of the alarm
You can set the sensitivity of the alarm for the
radar guard zones, to define the size of the
target that will trigger the alarm. The size of
target is shown as a percentage.
100% is maximum sensitivity, meaning that
very small targets will trigger the guard zone
alarm. 0% is minimum sensitivity, meaning
that only very large targets will trigger the
alarm.
•
•
•
•
•
•
Guard Zone: The number shows the
radar guard zone that is selected.
The same sensitivity setting is applied to
both of the radar guard zones if both are
turned on.
Sector or Circular: The shape of the
radar guard zone.
INR: The distance between the inner
boundary and your boat.
To set the alarm:
1
2
3
From the radar window, press
select Guard Zone.
Select Zonethen select 1(radar guard
zone 1) or 2(radar guard zone 2).
Select Alarm sensitivity then use and
to decrease or increase the setting.
then
OUR: The distance between the outer
boundary and your boat.
WDT: The angular width of the radar
guard zone (in degrees).
BRG: The bearing of a line drawn from
your boat through the centre of the
radar guard zone (in degrees).
Radar setup
Note: This option is shown only when the
radar is enabled (see Manual, 18-3)
Rotation
The current radar rotation is shown in the top
left corner of the radar screen. If COG data or
heading data is not available from a compass,
the radar rotation is automatically set to Head
up.
1
Press
twice to display the Setup
menu, then select Radar:
However, you are strongly recommended
to use a good quality product (such as a
NAVMAN HS02, HS03 or Autopilot) to provide
heading data.
If heading data is available from a compass,
the options are:
•
North up works only when COG data or
heading data from a heading sensor is
available. North is always at the top of the
radar screen.
You can easily compare the radar screen to
a chart in North up.
16
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Head up means that the radar image
rotates underneath your boat, so the
direction in which you are heading is
pointing to the top of the radar screen.
a spiral pattern. Generally, the stronger the
interference, the wider the interference lines.
Use the interference rejection option to
reduce both the interference patterns and
the width of the interference lines.
You can easily compare the visual view in
front of your boat with the radar screen.
There are four choices:
•
Course up works only when COG data or
heading data from a heading sensor is
available and there is an active route. It
means that your desired heading is always
pointing to the top of the radar screen
so that you can compare the leg bearing
of the active route with the radar screen.
(If you’re in Course up rotation but don’t
have an active route, the radar uses Head
up rotation until a route is made active.)
•
•
Off. Interference rejection is off.
Low operates the interference rejection at
minimum strength.
•
•
Medium operates the interference
rejection at medium strength.
High operates the interference rejection at
maximum strength. This setting can make
it more difficult to detect some targets
and radar beacons. Use this setting only
when necessary.
Motion mode
Palette
True motion mode is not available if there
is no position data, and no heading or
COG data. However, you are strongly
recommended to use a good quality product
(such as a NAVMAN HS02, HS03 or Autopilot)
to provide heading data.
Select the color scheme for the radar window.
Digit size
The range of the radar is shown on the radar
window; for example 1/16. You can show this
information in small, medium or large digits.
There are two choices:
Range ring
The range rings help you to quickly estimate
the range of a target from your boat.
•
Relative (RM). Your boat remains in a fixed
location on the radar screen and all other
objects move relative to your position.
(You can choose the position of the fixed
location, see Section 18-10). RM is the
default.
The range rings are shown. The number of
range rings and the spacing interval between
them is set automatically according to the
range setting. The current spacing interval
is shown in the top left corner of the radar
window.
•
True (TM). Your boat, and moving targets,
move across the radar screen as you travel.
All stationary objects remain in a fixed
position. You must have position data, and
heading or COG data for this option to be
Compass
The compass ring is displayed.
available.
North line
Interference filter
Whatever the radar windorotation, you can
always show the blue North line.
If the radar on another boat is operating
at the same frequency as your radar, it can
cause interference patterns on the radar
window.
If the bearing mode is set to:
•
magnetic, the North line always points to
magnetic North.
Interference patterns always appear in a
different place with each sweep. They can
be randomly scattered bright dots or dotted
lines that extend from the centre to the
edge of the radar window, often producing
•
true, the North line always points to true
North.
Show the North line.
Hide the North line.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust this on a chart window with the radar
overlay on.
Heading line
The heading line is a white line that extends
from your boat to the edge of the radar
window.
1
Select Zero bearingthen use the
arrow keys to enter the new bearing angle.
Show the heading line.
Hide the heading line.
Zero range
The zero range is also known as the radar
range offset and as the trigger delay.
Setup > Radar > Installation
If your radar window shows a blank, black
circle around the centre or a solid circle of
color at the centre, you need to adjust the
zero range setting until this circle disappears
or almost disappears. Ideally, the radar sweep
should start at your boat (a radar range of
zero).
Note: This option is shown only when the
radar is enabled (see Manual, 18-3)
1
2
Press
twice to display the Setup
menu, then select Radar.
Select Installation:
To adjust the zero range setting:
1
Position your boat about 45 to 90 m (50
to 100 yards) away from and parallel to a
straight-walled jetty or similar feature.
2
Adjust the gain setting if necessary, so
that a reasonably good image of the jetty
echo is displayed on the radar window. At
this stage, the jetty echo may appear to be
bent.
Park position
If your radar has an open array and you
take it out of enabled mode, the open array
continues to rotate for a short distance before
it finally stops. The stop position is known as
the park position. You can adjust the angle of
the parking position so that the open array
will always stop at your preferred position; for
example, facing the bow.
3
Select Zero range then use the arrow keys
to adjust the zero range setting until the
jetty echo appears as a straight line on the
radar window.
1
Select Park positionthen enter the
angle of the new park position.
Note: You may need to try a few different
park positions to find the correct one. The
strength of the wind will also affect the park
position.
Antenna height
Zero bearing
The Installation Manual for your NAVMAN
radar explains how to find the optimum
height for your radar scanner (antenna).
Use the zero bearing alignment to rotate the
radar image, one degree at a time, so that a
known object dead ahead is directly under
the boat’s heading marker.
Select Antenna height then enter the height of
the antenna above sea level.
This means that the radar image is aligned
with the displayed chart and the compass.
An accurate bearing alignment is particularly
important when the radar image is overlaid
onto the chart.
18
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar problems
Radar overlay doesn’t appear on the chart
screen
Radar shows false echoes and/or
background noise
a
Ensure that your boat is shown on the
radar window. If it is, but the radar overlay
still isn’t shown, try zooming in on the
charted area. (The charted area may be
outside the maximum range of the radar).
False echoes and/or background noise can
be produced if the radar sensitivity is too
high.
a
Try using the Auto setting for the radar
gain mode. If this doesn’t work, or if the
radar gain mode is already set to Auto, use
the radar gain setting to reduce the radar
sensitivity.
b
The threshold or transparency settings for
the radar overlay are not correct.
Radar shows arcs and/or shadows
Side lobe patterns often appear as an arc
or a broken arc. Shadows are blind spots.
Radar shows multiple echoes off the same
object
If the radar is installed at a suitable height
and in a suitable location on your boat,
side lobe patterns and shadows caused by
obstructions such as funnels or masts will
be minimized.
Multiple echoes off the same object are
most likely to occur when you are close
to a large target, and are usually only a
temporary nuisance.
Radar shows random or grouped dots
If you are having problems with these,
you may need to relocate your scanner.
Consult the Installation Guide for your
radar model for advice.
Rain clutter often appears as random dots
that can merge into badly-defined echoes
on the radar window. The random signals
are returned from rain, hail, sleet, or snow
and can result in a confusing display
Radar shows different patterns on
each sweep
Radar shows random signals in centre
Interference patterns always appear in
a different place with each sweep. They
can be randomly scattered bright dots or
dotted lines that extend from the centre
to the edge of the radar window, often
producing a spiral effect. Generally, the
stronger the interference, the wider the
interference lines.
Sea clutter usually appears as confusing,
random signals around your boat. High
waves will produce the maximum amount
of sea clutter.
You can optimize your radar window to
reduce the effects of sea clutter.
a
Use the interference rejection feature
to reduce interference patterns, and the
width of the interference lines.
NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical Dimensions
NAVMAN 8120
NAVMAN 8084
Download from Www.Somanuals.com. All Manuals Search And Download.
Lat 36° 48.404’S
Made in New Zealand
MN000753B-G
N av m a n 8D1o2w0n/lo8ad0f8ro4m FWuwew.lS,omAaInSu,al&s.coRma.dAlal Mr aAnudadlseSneadrcuhmAnd Download.
|