Important Information
Warranty
The National Instruments 7340 is warranted against defects in materials and workmanship for a period of one year from the date of shipment,
as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective
during the warranty period. This warranty includes parts and labor.
The media on which you receive National Instruments software are warranted not to fail to execute programming instructions, due to defects
in materials and workmanship, for a period of 90 days from date of shipment, as evidenced by receipts or other documentation. National
Instruments will, at its option, repair or replace software media that do not execute programming instructions if National Instruments receives
notice of such defects during the warranty period. National Instruments does not warrant that the operation of the software shall be
uninterrupted or error free.
A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside of the package before
any equipment will be accepted for warranty work. National Instruments will pay the shipping costs of returning to the owner parts which are
covered by warranty.
National Instruments believes that the information in this document is accurate. The document has been carefully reviewed for technical
accuracy. In the event that technical or typographical errors exist, National Instruments reserves the right to make changes to subsequent
editions of this document without prior notice to holders of this edition. The reader should consult National Instruments if errors are suspected.
In no event shall National Instruments be liable for any damages arising out of or related to this document or the information contained in it.
EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CUSTOMER’S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF
NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR
DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF. This limitation of the liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including
negligence. Any action against National Instruments must be brought within one year after the cause of action accrues. National Instruments
shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover
damages, defects, malfunctions, or service failures caused by owner’s failure to follow the National Instruments installation, operation, or
maintenance instructions; owner’s modification of the product; owner’s abuse, misuse, or negligent acts; and power failure or surges, fire,
flood, accident, actions of third parties, or other events outside reasonable control.
Copyright
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying,
recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National
Instruments Corporation.
Trademarks
CVI™, IMAQ™, LabVIEW™, Measurement Studio™, National Instruments™, NI™, ni.com™, NI-Motion™, and RTSI™ are trademarks of
National Instruments Corporation.
Product and company names mentioned herein are trademarks or trade names of their respective companies.
Patents
For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txtfile
on your CD, or ni.com/patents.
WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS
(1) NATIONAL INSTRUMENTS PRODUCTS ARE NOT DESIGNED WITH COMPONENTS AND TESTING FOR A LEVEL OF
RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN
ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE EXPECTED TO CAUSE SIGNIFICANT
INJURY TO A HUMAN.
(2) IN ANY APPLICATION, INCLUDING THE ABOVE, RELIABILITY OF OPERATION OF THE SOFTWARE PRODUCTS CAN BE
IMPAIRED BY ADVERSE FACTORS, INCLUDING BUT NOT LIMITED TO FLUCTUATIONS IN ELECTRICAL POWER SUPPLY,
COMPUTER HARDWARE MALFUNCTIONS, COMPUTER OPERATING SYSTEM SOFTWARE FITNESS, FITNESS OF COMPILERS
AND DEVELOPMENT SOFTWARE USED TO DEVELOP AN APPLICATION, INSTALLATION ERRORS, SOFTWARE AND
HARDWARE COMPATIBILITY PROBLEMS, MALFUNCTIONS OR FAILURES OF ELECTRONIC MONITORING OR CONTROL
DEVICES, TRANSIENT FAILURES OF ELECTRONIC SYSTEMS (HARDWARE AND/OR SOFTWARE), UNANTICIPATED USES OR
MISUSES, OR ERRORS ON THE PART OF THE USER OR APPLICATIONS DESIGNER (ADVERSE FACTORS SUCH AS THESE ARE
HEREAFTER COLLECTIVELY TERMED “SYSTEM FAILURES”). ANY APPLICATION WHERE A SYSTEM FAILURE WOULD
CREATE A RISK OF HARM TO PROPERTY OR PERSONS (INCLUDING THE RISK OF BODILY INJURY AND DEATH) SHOULD
NOT BE RELIANT SOLELY UPON ONE FORM OF ELECTRONIC SYSTEM DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID
DAMAGE, INJURY, OR DEATH, THE USER OR APPLICATION DESIGNER MUST TAKE REASONABLY PRUDENT STEPS TO
PROTECT AGAINST SYSTEM FAILURES, INCLUDING BUT NOT LIMITED TO BACK-UP OR SHUT DOWN MECHANISMS.
BECAUSE EACH END-USER SYSTEM IS CUSTOMIZED AND DIFFERS FROM NATIONAL INSTRUMENTS' TESTING
PLATFORMS AND BECAUSE A USER OR APPLICATION DESIGNER MAY USE NATIONAL INSTRUMENTS PRODUCTS IN
COMBINATION WITH OTHER PRODUCTS IN A MANNER NOT EVALUATED OR CONTEMPLATED BY NATIONAL
INSTRUMENTS, THE USER OR APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING
THE SUITABILITY OF NATIONAL INSTRUMENTS PRODUCTS WHENEVER NATIONAL INSTRUMENTS PRODUCTS ARE
INCORPORATED IN A SYSTEM OR APPLICATION, INCLUDING, WITHOUT LIMITATION, THE APPROPRIATE DESIGN,
PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
FCC/Canada Radio Frequency Interference Compliance
Determining FCC Class
The Federal Communications Commission (FCC) has rules to protect wireless communications from interference. The FCC
places digital electronics into two classes. These classes are known as Class A (for use in industrial-commercial locations only)
or Class B (for use in residential or commercial locations). All National Instruments (NI) products are FCC Class A products.
Depending on where it is operated, this Class A product could be subject to restrictions in the FCC rules. (In Canada, the
Department of Communications (DOC), of Industry Canada, regulates wireless interference in much the same way.) Digital
electronics emit weak signals during normal operation that can affect radio, television, or other wireless products.
All Class A products display a simple warning statement of one paragraph in length regarding interference and undesired
operation. The FCC rules have restrictions regarding the locations where FCC Class A products can be operated.
FCC/DOC Warnings
This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the instructions
in this manual and the CE marking Declaration of Conformity*, may cause interference to radio and television reception.
Classification requirements are the same for the Federal Communications Commission (FCC) and the Canadian Department of
Communications (DOC).
Changes or modifications not expressly approved by NI could void the user's authority to operate the equipment under the FCC
Rules.
Class A
Federal Communications Commission
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference
at their own expense.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Compliance to EU Directives
Users in the European Union (EU) should refer to the Declaration of Conformity (DoC) for information pertaining to the CE
marking. Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information.
To obtain the DoC for this product, visit ni.com/hardref.nsf, search by model number or product line, and click the appropriate
link in the Certification column.
*
The CE marking Declaration of Conformity contains important supplementary information and instructions for the user or
installer.
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Chapter 1
RTSI ................................................................................................................1-2
What You Need to Get Started ......................................................................................1-2
National Instruments Application Software ..................................................................1-3
Optional Equipment.......................................................................................................1-3
Chapter 2
Configuration and Installation
Software Installation......................................................................................................2-1
Controller Configuration................................................................................................2-1
Hardware Installation.....................................................................................................2-4
Chapter 3
Chapter 4
Trajectory Generators......................................................................................4-2
Analog Feedback.............................................................................................4-2
Flash Memory..................................................................................................4-3
Axes and Motion Resources ..........................................................................................4-3
Axes.................................................................................................................4-3
Motion Resources............................................................................................4-4
© National Instruments Corporation
v
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Onboard Programs and Buffers..................................................................................... 4-5
Chapter 5
Analog Inputs.................................................................................................. 5-12
Wiring Concerns............................................................................... 5-13
Other Motion I/O Connection......................................................................... 5-14
Digital I/O Connector.................................................................................................... 5-15
PWM Features................................................................................................. 5-16
RTSI Connector............................................................................................................. 5-16
RTSI Signal Considerations............................................................................ 5-17
Appendix A
Specifications
Appendix B
Technical Support and Professional Services
Glossary
Index
NI 7340 User Manual
vi
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
This manual describes the electrical and mechanical aspects of the
PXI/PCI-7340 and contains information about how to operate and program
the device.
The 7340 is designed for PXI, Compact PCI, and PCI bus computers
Conventions
The following conventions appear in this manual:
<>
Angle brackets that contain numbers separated by an ellipsis represent a
range of values associated with a bit or signal name—for example,
DIO<3..0>.
»
The » symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
♦
The ♦ symbol indicates that the following text applies only to a specific
product, a specific operating system, or a specific software version.
This icon denotes a note, which alerts you to important information.
This icon denotes a caution, which advises you of precautions to take to
avoid injury, data loss, or a system crash.
bold
Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names.
italic
Italic text denotes variables, emphasis, a cross reference, or an introduction
to a key concept. This font also denotes text that is a placeholder for a word
or value that you must supply.
monospace
Text in this font denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames and extensions, and code excerpts.
© National Instruments Corporation
vii
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Related Documentation
The following documents contain information you might find helpful as
you read this manual:
•
•
•
NI-Motion User Manual
NI-Motion C Reference Help
NI-Motion VI Reference Help
NI 7340 User Manual
viii
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
This chapter includes information about the features of the PXI/PCI-7340
controller and information about operating the device.
About the 7340 Controller
The 7340 controller features advanced motion control with easy-to-use
software tools and add-on motion VI libraries for use with LabVIEW.
Features
The 7340 is a combination servo and stepper motor controller for PXI,
Compact PCI, and PCI bus computers. The 7340 provides fully
programmable motion control for up to four independent or coordinated
axes of motion, with dedicated motion I/O for limit and home switches and
additional I/O for general-purpose functions.
You can use the 7340 to perform arbitrary and complex motion trajectories
using stepper motors or servo devices.
Servo axes can control servo motors, servo hydraulics, servo valves, and
other servo devices. Servo axes always operate in closed-loop mode. These
axes use quadrature encoders or analog inputs for position and velocity
feedback and provide analog command outputs with an industry-standard
range of 10 V.
Stepper axes can operate in open or closed-loop mode. In closed-loop
mode, they use quadrature encoders or analog inputs for position and
velocity feedback (closed-loop only), and provide step/direction or
clockwise (CW) /counter-clockwise (CCW) digital command outputs.
All stepper axes support full, half, and microstepping applications.
Hardware
The 7340 uses an advanced dual-processor architecture that uses a 32-bit
CPU, combined with a digital signal processor (DSP) and custom field
programmable gate arrays (FPGAs), making the controller a
high-performance device. The first-in-first-out (FIFO) bus interface and
© National Instruments Corporation
1-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
powerful function set provide high-speed communications while
off-loading complex motion functions from the host PC for optimum
10 simultaneous motion programs.
The 7340 features motion profiles that are controlled with enhanced
PID/PIVff servo updates. Each axis has motion I/O for end-of-travel limit
and home switch inputs, breakpoint output, trigger input, and encoder
feedback. Refer to Appendix A, Specifications, for information about the
feedback rates. The 7340 also has non-dedicated user I/O including 32 bits
of digital I/O and four analog inputs for 10 V signals, joystick inputs, or
monitoring of analog sensors. Additionally, the 7340 analog inputs can
provide feedback for loop closure.
RTSI
The 7340 supports the National Instruments Real-Time System Integration
(RTSI) bus. The RTSI bus provides high-speed connectivity between
National Instruments products, including image acquisition (IMAQ) and
data acquisition (DAQ) products. Using the RTSI bus, you can easily
synchronize several functions to a common trigger or timing event across
multiple motion, IMAQ, or DAQ devices.
What You Need to Get Started
To set up and use the 7340 controller, you must have the following items:
❑ NI PXI-7340 or PCI-7340 motion controller
❑ This manual
❑ NI-Motion 6.1 or later driver software and documentation
❑ One of the following software packages and documentation:
–
–
–
–
–
LabVIEW 6.0 or later
LabWindows™/CVI™
Measurement Studio
C/C++
Microsoft Visual Basic
❑ A computer with an available PXI or PCI slot
NI 7340 User Manual
1-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Software Programming Choices
NI-Motion is a simple but powerful high-level application programming
interface (API) that makes programming the 7340 easy. All setup and
motion control functions are easily executed by calling into a
dynamically-linked library (DLL). You can call these libraries from C,
Microsoft Visual Basic, and other high-level languages. Full function sets
are available for LabVIEW, LabWindows/CVI, and other
industry-standard software programs.
National Instruments Application Software
LabVIEW is based on the graphical programming language, G, and
features interactive graphics and a state-of-the-art user interface. In
LabVIEW, you can create 32-bit compiled programs and stand-alone
executables for custom automation, data acquisition, test, measurement,
and control solutions. National Instruments offers the NI-Motion driver
software support for LabVIEW, which includes a series of virtual
instruments (VIs) for using LabVIEW with National Instruments motion
control hardware. The NI-Motion VI library implements the NI-Motion
API and a powerful set of demo functions; example programs; and fully
operational, high-level application routines.
ANSI C-based LabWindows/CVI also features interactive graphics and a
state-of-the-art user interface. Using LabWindows/CVI, you can generate
C code for custom data acquisition, test, and measurement and automation
solutions. NI-Motion includes a series of sample programs for using
LabWindows/CVI with National Instruments motion control hardware.
Optional Equipment
National Instruments offers a variety of products for use with the
7340 controller, including the following accessories:
•
•
Cables and cable assemblies for motion and digital I/O
Universal Motion Interface (UMI) wiring connectivity blocks with
integrated motion signal conditioning and motion inhibit functionality
•
•
Stepper and servo motor compatible drive amplifier units with
integrated power supply and wiring connectivity
Connector blocks and shielded and unshielded 68-pin screw terminal
wiring aids
© National Instruments Corporation
1-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
For more specific information about these products, refer to the
National Instruments catalog, the National Instruments Web site at
ni.com, or call your National Instruments sales representative.
Motion I/O Connections
The external motion and digital I/O connectors on the 7340 are
high-density, 68-pin female VHDCI connectors.
For custom cables, use the AMP mating connector (part number
787801-1).
NI 7340 User Manual
1-4
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Configuration and Installation
This chapter describes how to configure and install the PXI/PCI-7340.
Software Installation
Before installing the 7340, install the NI-Motion driver software. Refer to
the Getting Started with NI Motion Control manual, which is included with
the controller, for specific installation instructions.
Note If you do not install the NI-Motion driver software before attempting to use the
7340, the system does not recognize the 7340 and you are unable to configure or use the
device.
Controller Configuration
Because motion I/O-related configuration of the 7340 is performed entirely
with software, it is not necessary to set jumpers for motion I/O
configuration.
The PXI-7340 and PCI-7340 controllers are fully compatible with the
industry standard PXI Specification, Revision 2.0 and the PCI Local Bus
Specification, Revision 2.2, respectively. This compatibility allows the PXI
or PCI system to automatically perform all bus-related configuration and
requires no user interaction. It is not necessary to configure jumpers for
bus-related configuration, including setting the device base memory and
interrupt channel.
Safety Information
Caution The following paragraphs contain important safety information you must follow
when installing and operating the 7340 and all devices connecting to the 7340.
Do not operate the device in a manner not specified in the documentation.
Misuse of the device may result in a hazard and may compromise the safety
protection built into the device. If the device is damaged, turn it off and do
© National Instruments Corporation
2-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Configuration and Installation
not use it until service-trained personnel can check its safety. If necessary,
return the device to National Instruments for repair.
Keep away from live circuits. Do not remove equipment covers or shields
unless you are trained to do so. If signal wires are connected to the device,
hazardous voltages can exist even when the equipment is turned off. To
avoid a shock hazard, do not perform procedures involving cover or shield
removal unless you are qualified to do so. Disconnect all field power prior
to removing covers or shields.
If the device is rated for use with hazardous voltages (>30 Vrms, 42.4 Vpk,
or 60 Vdc), it may require a safety earth-ground connection wire. Refer to
the device specifications for maximum voltage ratings.
Because of the danger of introducing additional hazards, do not install
unauthorized parts or modify the device. Use the device only with the
chassis, modules, accessories, and cables specified in the installation
instructions. All covers and filler panels must be installed while operating
the device.
Do not operate the device in an explosive atmosphere or where flammable
gases or fumes may be present. Operate the device only at or below the
pollution degree stated in the specifications. Pollution consists of any
foreign matter—solid, liquid, or gas—that may reduce dielectric strength
or surface resistivity. Pollution degrees are listed below.
•
Pollution Degree 1—No pollution or only dry, nonconductive
pollution occurs. The pollution has no effect.
•
Pollution Degree 2—Normally only nonconductive pollution occurs.
Occasionally, nonconductive pollution becomes conductive because of
condensation.
•
Pollution Degree 3—Conductive pollution or dry, nonconductive
pollution occurs. Nonconductive pollution becomes conductive
because of condensation.
Note The 7340 is intended for indoor use only.
Clean the device and accessories by brushing off light dust with a soft,
nonmetallic brush. Remove other contaminants with a stiff, nonmetallic
brush. The unit must be completely dry and free from contaminants before
returning it to service.
You must insulate signal connections for the maximum voltage for which
the device is rated. Do not exceed the maximum ratings for the device.
NI 7340 User Manual
2-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Configuration and Installation
Remove power from signal lines before connection to or disconnection
from the device.
Caution National Instruments measurement products may be classified as either
Installation Category I or II. Operate products at or below the Installation Category level
specified in the hardware specifications.
Installation Category1: Measurement circuits are subjected to working
voltages2 and transient stresses (overvoltage) from the circuit to which they
are connected during measurement or test. Installation Category establishes
standardized impulse withstand voltage levels that commonly occur in
electrical distribution systems. The following is a description of Installation
(Measurement3) Categories:
•
Installation Category I is for measurements performed on circuits not
directly connected to the electrical distribution system referred to as
MAINS4 voltage. This category is for measurements of voltages from
specially protected secondary circuits. Such voltage measurements
include signal levels, special equipment, limited-energy parts of
equipment, circuits powered by regulated low-voltage sources, and
electronics.
•
•
Installation Category II is for measurements performed on circuits
directly connected to the electrical distribution system. This category
refers to local-level electrical distribution, such as that provided by a
standard wall outlet (e.g., 115 V for U.S. or 230 V for Europe).
Examples of Installation Category II are measurements performed on
household appliances, portable tools, and similar products.
Installation Category III is for measurements performed in the building
installation at the distribution level. This category refers to
measurements on hard-wired equipment such as equipment in fixed
installations, distribution boards, and circuit breakers. Other examples
are wiring, including cables, bus-bars, junction boxes, switches,
socket-outlets in the fixed installation, and stationary motors with
permanent connections to fixed installations.
•
Installation Category IV is for measurements performed at the primary
electrical supply installation (<1,000 V). Examples include electricity
1
2
3
4
Installation Categories as defined in electrical safety standard IEC 61010-1.
Working voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.
Installation Category is also referred to as Measurement Category.
MAINS is defined as the (hazardous live) electrical supply system to which equipment is designed to be connected for the
purpose of powering the equipment. Suitably rated measuring circuits may be connected to the MAINS for measuring
purposes.
© National Instruments Corporation
2-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Configuration and Installation
meters and measurements on primary overcurrent protection devices
and on ripple control units.
Hardware Installation
Install the 7340 in any open compatible expansion slot in the PXI or PCI
system. Appendix A, Specifications, lists the typical power required for
each controller.
The following instructions are for general installation. Consult the
computer user manual or technical reference manual for specific
instructions and warnings.
Caution The 7340 is a sensitive electronic device shipped in an antistatic bag. Open only
at an approved workstation and observe precautions for handling electrostatic-sensitive
devices.
Note When adding or removing a controller from a Windows 2000/NT/XP system, you
must be logged on with administrator-level access. After you have restarted the system, you
may need to refresh Measurement & Automation Explorer (MAX) to view the new
controller.
♦
PXI-7340
1. Power off and unplug the chassis.
Caution To protect yourself and the computer from electrical hazards, the computer must
remain unplugged until the installation is complete.
2. Choose an unused +3.3 V or +5 V peripheral slot and remove the filler
panel.
3. Touch a metal part on the chassis to discharge any static electricity that
might be on your clothes or body. Static electricity can damage the
controller.
4. Insert the PXI controller into the chosen slot. Use the injector/ejector
handle to fully inject the device into place.
5. Screw the front panel of the PXI controller to the front panel mounting
rails of the chassis.
6. Visually verify the installation.
7. Plug in and power on the chassis.
NI 7340 User Manual
2-4
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Configuration and Installation
♦
PCI-7340
1. Power off and unplug the computer.
Caution To protect yourself and the computer from electrical hazards, the computer must
remain unplugged until the installation is complete.
2. Remove the cover to expose access to the PCI expansion slots.
3. Choose an unused 5 V PCI slot, and remove the corresponding
expansion slot cover on the back panel of the computer.
4. Touch a metal part on the computer case to discharge any static
electricity that might be on your clothes or body before handling the
controller. Static electricity can damage the controller.
5. Gently rock the controller into the slot. The connection may be tight,
but do not force the controller into place.
6. If required, screw the mounting bracket of the controller to the back
panel rail of the computer.
7. Replace the cover.
8. Plug in and power on the computer.
© National Instruments Corporation
2-5
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Hardware Overview
This chapter presents an overview of the PXI/PCI-7340 hardware
functionality.
Figures 3-1 and 3-3 show the PXI-7340 and PCI-7340 parts locator
diagrams, respectively.
1
5
4
3
2
1
2
3
Serial Number Label
DSP
CPU
4
5
68-Pin Digital I/O Connector
68-Pin Motion I/O Connector
Figure 3-1. PXI-7340 Parts Locator Diagram
Note The PXI-7340 assembly number is located on the back of the PXI module.
© National Instruments Corporation
3-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
1
2
3
1
2
Identification Number Used in Australia
Symbol Indicating FFC Compliance
3
Symbol to Alert User to Read the Manual
Figure 3-2. Symbols on the Back of the PXI-7340
9
10
1
2
3
8
7
4
5
ASSY186307D-01
6
1
2
3
4
5
RTSI Connector
Serial Number Label
Symbol to Alert User to Read the Manual
Symbol Indicating FFC Compliance
Identification Number Used in Australia
6
7
8
9
Assembly Number Label
68-Pin Digital I/O Connector
68-Pin Motion I/O Connector
CPU
10 DSP
Figure 3-3. PCI-7340 Parts Locator Diagram
NI 7340 User Manual
3-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Overview
The 68-pin motion I/O connector provides all the signals for four axes of
inputs, breakpoint outputs, trigger inputs, digital-to-analog (DAC), and
analog-to-digital (ADC) converter signals. Refer to Chapter 5, Signal
Connections, for details about the signals in the motion I/O connector.
The 68-pin digital I/O connector provides 32 bits of user-configurable
digital I/O. Refer to Chapter 5, Signal Connections, for details about the
signals in the digital I/O connector.
The PCI-7340 RTSI connector provides up to eight triggers to facilitate
synchronization between multiple National Instruments products. The
PXI-7340 RTSI-enabled connection provides up to eight triggers and one
PXI star trigger to facilitate synchronization between multiple National
Instruments PXI-enabled products. Typical applications of the RTSI bus
include triggering an image acquisition or DAQ measurement based on
motion events, or capturing current motion positions based on events
external to the motion controller. You also can use the RTSI bus for general
hardware-based communication between RTSI devices.
The RTSI bus also can be used for general-purpose I/O. Refer to Chapter 5,
Signal Connections, for details about RTSI connector signals.
© National Instruments Corporation
3-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Functional Overview
This chapter provides an overview of motion control algorithms and the
PXI/PCI-7340 controller.
Dual Processor Architecture
With the 7340, you can perform up to four axes of simultaneous,
coordinated motion control in a preemptive, multitasking, real-time
environment.
An advanced dual-processor architecture that uses a 32-bit CPU combined
with a digital signal processor (DSP) and custom FPGAs give the 7340
high-performance capabilities. The FIFO bus interface and powerful
function set provide high-speed communications while off-loading
complex motion functions from the host PC for optimized system
performance.
The 7340 uses the DSP for all closed-loop control, including position
tracking, PID control closed-loop computation, and motion trajectory
generation. The DSP chip is supported by custom FPGAs that perform the
high-speed encoder interfacing, position capture and breakpoint functions,
motion I/O processing, and stepper pulse generation for hard real-time
functionality.
The embedded, multitasking real-time CPU handles host communications,
command processing, multi-axis interpolation, onboard program
execution, error handling, general-purpose digital I/O, and overall motion
system integration functions.
© National Instruments Corporation
4-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Functional Overview
Embedded Real-Time Operating System (RTOS)
The embedded firmware is based on an embedded RTOS kernel and
provides optimum system performance in varying motion applications.
Motion tasks are prioritized. Task execution order depends on the priority
of each task, the state of the entire motion system, I/O or other system
events, and the real-time clock.
The DSP chip is a separate processor that operates independently from
the CPU but is closely synchronized. The 7340 is a true multiprocessing
and multitasking embedded controller.
The advanced architecture of the 7340 enables advanced motion features,
such as enhanced PID functions. Refer to the NI-Motion User Manual for
more information about the features available on the 7340.
Trajectory Generators
The 7340 trajectory generators calculate the instantaneous position
command that controls acceleration and velocity while it moves the axis to
its target position. Depending on how you configure the axis, this command
is then sent to the PID servo loop or stepper pulse generator.
To implement infinite trajectory control, the 7340 has eight trajectory
generators implemented in the DSP chip (two per axis). Each generator
calculates an instantaneous position for each PID update period. While
simple point-to-point moves require only one trajectory generator,
two simultaneous generators are required for blended moves and infinite
trajectory control processing.
Analog Feedback
The 7340 has an 8-channel multiplexed, 12-bit ADC. The converted analog
values are broadcast to both the DSP and CPU through a dedicated internal
high-speed serial bus. The multiplexer provides the high sampling rates
required for feedback loop closure, joystick inputs, or monitoring analog
sensors. Refer to Appendix A, Specifications, for the multiplexer scan rate.
Four of these channels are intended for calibration, leaving the other four
available for analog feedback.
NI 7340 User Manual
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Chapter 4
Functional Overview
Flash Memory
Nonvolatile memory on the 7340 is implemented with flash ROM, which
means that the controllers can electrically erase and reprogram their own
ROM. Because all the 7340 embedded firmware, including the RTOS and
DSP code, is stored in flash memory, you can upgrade the onboard
firmware contents in the field for support and new feature enhancement.
Flash memory also allows objects such as programs and data arrays to be
stored in non-volatile memory. It is possible to save the entire parameter
state of the controller to the flash memory. On the next power cycle, the
controller automatically loads and returns the configuration to these new
saved default values.
The FPGA configuration programs also are stored in the flash ROM.
At power-up, the FPGAs are booted with these programs, which means
that updates to the FPGA programs can be performed in the field.
A flash memory download utility is included with the NI-Motion software
that ships with the controller.
Axes and Motion Resources
The 7340 can control up to four axes of motion. The axes can be completely
independent, simultaneously coordinated, or mapped in multidimensional
groups called coordinate spaces. You also can synchronize coordinate
spaces for multi-vector space coordinated motion control.
Axes
At a minimum, an axis consists of a trajectory generator, a PID (for servo
axes) or stepper control block, and at least one output resource—either
a DAC output (for servo axes) or a stepper pulse generator output. Servo
axes must have either an encoder or ADC channel feedback resource.
Closed-loop stepper axes also require a feedback resource, while open-loop
stepper axes do not. Figures 4-1 and 4-2 show these axis configurations.
With the 7340, you can map one or two feedback resources and one or two
output resources to the axis. An axis with its primary output resource
mapped to a stepper output is by definition a stepper axis. An axis with its
primary output resource mapped to a DAC is by definition a servo axis.
© National Instruments Corporation
4-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Functional Overview
101100111
øA
32-Bit
Encoder
Interface
16-Bit
D/A
Converter
PID
Servo 11101101100
Loop
0101011101101
øB
10 V
101100111
Index
Figure 4-1. Servo Axis Resources
Trajectory
Generator
101100111
øA
Stepper
Pulse
Generator
Stepper
Control
Loop
32-Bit
Encoder
Interface
010010110
01011010
Optional
101100111
Index
Figure 4-2. Stepper Axis Resources
The 7340 supports axes with secondary output resources, such as DACs for
servo axes or stepper outputs. Defining two output resources is useful when
controlling axes with multiple motors, such as gantry systems in which
two DAC outputs can be configured with different torque limits and/or
offsets.
The 7340 controller also supports secondary feedback resources, called
encoders, for axes defined as servo. Two feedback resources are used when
implementing dual-loop control, such as in backlash compensation,
which reduces the number of encoders available for other axes.
Note Refer to the NI-Motion User Manual for information about configuring axes.
Motion Resources
Encoder, DAC, ADC, and motion I/O resources that are not used by an axis
are available for non-axis or nonmotion-specific applications. You can
directly control an unmapped DAC as a general-purpose analog output
( 10 V). Similarly, you can use any ADC channel to measure
potentiometers or other analog sensors.
NI 7340 User Manual
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Chapter 4
Functional Overview
If an encoder resource is not needed for axis control, you can use it for any
number of other functions, including position or velocity monitoring, as a
digital potentiometer encoder input, or as a master encoder input for
master/slave (electronic gearing) applications.
Each axis also has an associated forward and reverse limit input, a home
input, a high-speed capture trigger input, a breakpoint output, and an inhibit
output. These signals can be used for general-purpose digital I/O when not
being used for their motion-specific purpose.
Onboard Programs and Buffers
The 7340 controller has full onboard programmability capable of executing
up to 10 simultaneous motion programs.
You can execute the NI-Motion function set from onboard programs.
In addition, the onboard programs support basic math and data operation
functions for up to 120 general-purpose variables.
You can store and run onboard programs and buffers from RAM or save
them to flash ROM. The 7340 controller has 64 KB of RAM and 128 KB
of ROM that is divided into two 64 KB sectors for program and buffer
storage. You can store and run programs and buffers from either RAM or
ROM, but you cannot split programs between the two, and you cannot split
programs or buffers between the two 64 KB ROM sectors.
Note Refer to the NI-Motion User Manual for detailed information about all of these
onboard programming and buffer features.
Host Communications
The host computer communicates with the controller through a number of
memory port addresses on the host bus. The host bus can be either PXI or
PCI.
The primary bidirectional data transfer port supports FIFO data passing
in both send and readback directions. The 7340 controller has both a
command buffer for incoming commands and a return data buffer (RDB)
for returning data.
© National Instruments Corporation
4-5
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Functional Overview
The communications status register (CSR) provides bits for
communications handshaking as well as real-time error reporting and
general status feedback to the host PC. The move complete status (MCS)
register provides instantaneous motion status of all axes.
NI 7340 User Manual
4-6
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Signal Connections
This chapter describes how to make input and output signal connections
directly to the PXI/PCI-7340 as well as general information about the
associated I/O circuitry.
The 7340 has three connectors that handle all signals to and from the
external motion system.
•
•
•
68-pin motion I/O connector
68-pin digital I/O connector
RTSI connector
You can connect to your motion system with cables and accessories,
varying from simple screw terminal blocks to enhanced Universal Motion
Interface (UMI) units and drives.
Note The 7340 does not provide isolation between circuits.
Caution Turn off power to all devices when connecting or disconnecting the
7340 controller motion I/O and auxiliary digital I/O cables. Failure to do so may damage
the controller.
Motion I/O Connector
The motion I/O connector contains all of the signals required to control up
to four axes of servo and stepper motion, including the following features:
•
•
•
•
•
•
Motor command analog and stepper outputs
Encoder feedback inputs
Forward, home, and reverse limit inputs
Breakpoint outputs
Trigger inputs
Inhibit outputs
The motion I/O connector also contains four channels of 12-bit A/D inputs
for analog feedback or general-purpose analog input.
© National Instruments Corporation
5-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Figure 5-1 shows the pin assignments for the 68-pin motion I/O connector
on the 7340. Table 5-1 includes descriptions for each of the signals. A line
above a signal name indicates that the signal is active-low.
1
2
3
4
5
6
7
8
9
35
36
37
38
39
40
41
42
43
Axis 1 Dir (CCW)
Digital Ground
Digital Ground
Axis 1 Home Switch
Trigger 1
Axis 1 Step (CW)
Axis 1 Encoder Phase A
Axis 1 Encoder Phase B
Axis 1 Encoder Index
Axis 1 Forward Limit Switch
Axis 1 Reverse Limit Switch
Axis 2 Step (CW)
Axis 1 Inhibit
Axis 2 Dir (CCW)
Digital Ground
Digital Ground
Axis 2 Home Switch
Trigger 2
Axis 2 Encoder Phase A
Axis 2 Encoder Phase B
Axis 2 Encoder Index
10 44
11 45
12 46
13 47
Axis 2 Forward Limit Switch
Axis 2 Reverse Limit Switch
Axis 3 Step (CW)
Axis 2 Inhibit
Axis 3 Dir (CCW)
Digital Ground 14 48
Digital Ground 15 49
Axis 3 Encoder Phase A
Axis 3 Encoder Phase B
Axis 3 Encoder Index
Axis 3 Home Switch
16 50
17 51
18 52
19 53
20 54
Trigger 3
Axis 3 Inhibit
Axis 3 Forward Limit Switch
Axis 3 Reverse Limit Switch
Axis 4 Step (CW)
Axis 4 Encoder Phase A
Axis 4 Encoder Phase B
Axis 4 Encoder Index
Axis 4 Forward Limit Switch
Axis 4 Reverse Limit Switch
Host +5 V
Axis 4 Dir (CCW)
Digital Ground
Digital Ground 21 55
Axis 4 Home Switch 22 56
Trigger 4 23 57
Axis 4 Inhibit
24 58
25 59
Digital Ground
Breakpoint 1 26 60
Breakpoint 3
Digital Ground 28 62
Breakpoint 2
27 61
Breakpoint 4
Shutdown
Analog Output
Analog Output
29 63
30 64
31 65
Analog Output
Analog Output
Analog Output Ground
Reserved
Analog Input 1 32 66
Analog Input 3 33 67
Analog Input 2
Analog Input 4
Analog Reference (Output) 34 68
Analog Input Ground
Figure 5-1. 68-Pin Motion I/O Connector Pin Assignment
NI 7340 User Manual
5-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Table 5-1 describes the signals on the motion I/O connector.
Table 5-1. Motion I/O Signal Connections
Signal Name
Reference
Direction
Description
Motor direction or
Axis <1..4> Dir (CCW)
Digital Ground
Output
counter-clockwise control
Axis <1..4> Step (CW)
Digital Ground
Digital Ground
Output
Input
Motor step or clockwise control
Axis <1..4> Encoder Phase A
Closed-loop only—phase A encoder
input
Axis <1..4> Encoder Phase B
Axis<1..4> Encoder Index
Digital Ground
Digital Ground
Input
Input
Closed-loop only—phase B encoder
input
Closed-loop only—index encoder
input
Axis <1..4> Home Switch
Digital Ground
Digital Ground
Digital Ground
Input
Input
Input
Home switch
Axis <1..4> Forward Limit Switch
Axis <1..4> Reverse Limit Switch
Forward/clockwise limit switch
Reverse/counter-clockwise limit
switch
Axis <1..4> Inhibit
Trigger <1..4>
Digital Ground
Digital Ground
Output
Input
Drive inhibit
High-speed position capture trigger
input <1..4>
Breakpoint <1..4>
Host +5 V
Digital Ground
Digital Ground
—
Output
Output
—
Breakpoint output <1..4>
+5 V—host computer +5 V supply
Reference for analog inputs
12-bit analog input
Analog Input Ground
Analog Input <1..4>
Analog Output <1..4>
Analog Output Ground
Shutdown
Analog Input Ground
Analog Output Ground
—
Input
Output
—
16-bit analog output
Reference for analog outputs
Controlled device shutdown
+7.5 V—analog reference level
Reference for digital I/O
Digital Ground
Analog Input Ground
—
Input
Output
—
Analog Reference (output)
Digital Ground
© National Instruments Corporation
5-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Motion Axis Signals
The following signals control the servo amplifier or stepper driver.
•
Analog Output <1..4>—These 16-bit DAC outputs are typically
the servo command outputs for each axis. They can drive the
industry-standard 10 V output, and can be software limited to
any positive or negative voltage range. They also feature
a software-programmable voltage offset.
Although typically used as the command output of an axis control
loop, unused DACs also can function as independent analog outputs
for general-purpose control.
•
•
Analog Output Ground—To help keep digital noise separate from the
analog DAC outputs, there is a separate return connection. Use this
analog ground connection and not Digital Ground (digital I/O
reference) as the reference for the DAC outputs when connecting to
servo amplifiers.
Axis <1..4> Step (CW) and Dir (CCW)—These open-collector signals
are the stepper command outputs for each axis. The 7340 supports both
major industry standards for stepper command signals: step and
direction, or independent CW and CCW pulse outputs.
The output configuration and signal polarity is software programmable
for compatibility with various third-party drives, as follows:
–
When step and direction mode is configured, each commanded
step (or microstep) produces a pulse on the step output. The
direction output signal level indicates the command direction of
motion, either forward or reverse.
–
CW and CCW mode produces pulses (steps) on the CW output for
forward-commanded motion and pulses on the CCW output for
reverse-commanded motion.
In either case, you can set the active polarity of both outputs to
active-low (inverting) or active-high (non-inverting). For example,
with step and direction, you can make a logic high correspond to either
forward or reverse direction.
The Step (CW) and Dir (CCW) outputs are driven by high-speed
open-collector TTL buffers that feature 64 mA sink current capability
and built-in 3.3 kΩ pull-up resistors to +5 V.
buffers will fail if subjected to voltages in excess of +5.5 V.
NI 7340 User Manual
5-4
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
•
Axis <1..4> Inhibit—Use the inhibit output signals to control the
enable/inhibit function of a servo amplifier or stepper driver. When
properly connected and configured, the inhibit function causes the
connected motor to be de-energized and its shaft turns freely. These
open-collector inhibit signals feature 64 mA current sink capability
with built-in 3.3 kΩ pull-up resistors to +5 V, and can directly drive
most driver/amplifier inhibit input circuits.
While the industry standard for inhibits is active-low (inverting), these
outputs have programmable polarity and can be set to active-high
(non-inverting) for increased flexibility and unique drive
compatibility.
Inhibit output signals can be activated automatically upon a shutdown
condition, a Kill Motion command, or any motion error that causes a
kill motion condition, such as following error trip. You also can
directly control the inhibit output signals to enable or disable a driver
or amplifier.
Limit and Home Inputs
The following signals control limit and home inputs.
•
•
•
Axis <1..4> Forward Limit Input
Axis <1..4> Home Input
Axis <1..4> Reverse Limit Input
These inputs are typically connected to limit switches located at physical
ends of travel and/or at a specific home position. Limit and home inputs can
be software enabled or disabled at any time. When enabled, an active
transition on a limit or home input causes a full torque halt stop of the
associated motor axis. In addition, an active forward or reverse limit input
impedes future commanded motion in that direction for as long as the
signal is active.
Note By default, limit and home inputs are digitally filtered and must remain active for at
least 1 ms to be recognized. You can use MAX to disable digital filtering for limit and home
inputs. Active signals should remain active to prevent motion from proceeding further into
the limit. Pulsed limit signals stop motion, but they do not prevent further motion in that
direction if another move is started.
The input polarity of these signals is software programmable for active-low
(inverting) or active-high (non-inverting).
© National Instruments Corporation
5-5
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
You can use software disabled limit and home inputs as general-purpose
inputs. You can read the status of these inputs at any time and set and
change their polarity as required.
Limit and home inputs are a per axis enhancement on the 7340 and are not
required for basic motion control. These inputs are part of a system solution
for complete motion control.
Caution National Instruments recommends using limits for personal safety, as well as to
protect the motion system.
Wiring Concerns
For the end of travel limits to function correctly, the forward limit must be
located at the forward or positive end of travel, and the reverse limit at the
negative end of travel.
Caution Failure to follow these guidelines may result in motion that stops at, but then
travels through, a limit, potentially damaging the motion system. Miswired limits may
prevent motion from occurring at all.
Keep limit and home switch signals and their ground connections wired
separately from the motor driver/amplifier signal and encoder signal
connections.
Caution Wiring these signals near each other can cause faulty motion system operation
due to signal noise and crosstalk.
Limit and Home Input Circuit
By default, all limit and home inputs are digitally filtered and must be
active for at least 1 ms. You can use MAX to disable digital filtering for
limit and home inputs. Figure 5-2 shows a simplified schematic diagram of
the circuit used by the limit and home switch inputs for input signal
buffering and detection.
NI 7340 User Manual
5-6
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Vcc
3.3 kΩ
To the limit and home
switch circuits
74FCT244
1 kΩ
1/8 W
From the external
connector limit
and home switch pins
DGND
Figure 5-2. Limit and Home Input Circuit
Caution Excessive input voltages can cause erroneous operation and/or component
failure. Verify that the input voltage is within the specification range.
Encoder Signals
The 7340 offers four channels of single-ended quadrature encoder inputs.
All National Instruments power drives and UMI accessories provide
built-in circuitry that converts differential encoder signals to single-ended
encoder signals. Each channel consists of a Phase A, Phase B, and Index
input, as described in the following sections.
Encoder <1..4> Phase A/Phase B
The encoder inputs provide position and velocity feedback for absolute
and relative positioning of axes in any motion system configuration.
If an encoder resource is not needed for axis control, it is available for other
functions including position or velocity monitoring, digital potentiometer
encoder inputs, or as a master encoder input for master/slave (electronic
gearing) applications.
The encoder channels (Encoder <1..4>) are implemented in an FPGA
and are high performance with extended input frequency response and
advanced features, such as high-speed position capture inputs and
breakpoint outputs.
An encoder input channel converts quadrature signals on Phase A and
Phase B into 32-bit up/down counter values. Quadrature signals are
generated by optical, magnetic, laser, or electronic devices that provide
two signals, Phase A and Phase B, that are 90° out of phase. The leading
phase, A or B, determines the direction of motion. The four transition states
© National Instruments Corporation
5-7
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
of the relative signal phases provide distinct pulse edges that cause count
up or count down pulses in the direction determined by the leading phase.
A typical encoder with a specification of N (N = number) lines per unit
of measure (revolutions or linear distance) produces 4 × N quadrature
counts per unit of measure. The count is the basic increment of position
in NI-Motion systems.
Tip Determine quadrature counts by multiplying the encoder resolution in encoder lines
by four. The encoder resolution is the number of encoder lines between consecutive
encoder marker or Z-bit indexes. If the encoder does not have an index output, the
resolution is referred to as lines per revolution, or lines per unit of measure, such as inch,
centimeter, millimeter, and so on.
Encoder <1..4> Index
The Index input is primarily used to establish a reference position. This
function uses the number of counts per revolution or the linear distance to
initiate a search move that locates the index position. When a valid Index
signal transition occurs during a Find Reference routine, the position of the
Index signal is captured accurately. Use this captured position to establish
system position reference required.
The default MAX settings guarantee that the Find Index routine completes
successfully if the encoder generates a high index pulse when phases A
and B are low and the encoder is connected through an NI UMI or drive
accessory. Figure 5-3 shows the default encoder phasing diagram at the
inputs to the controller.
Phase A
Phase B
Index
Figure 5-3. Quadrature Encoder Phasing Diagram
You can set the index reference criteria in MAX to change the pattern of
phases A and B for the index search. You also can set the encoder polarity
for phases A, B, and I in MAX.
NI 7340 User Manual
5-8
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Wiring Concerns
The encoder inputs are connected to quadrature decoder/counter circuits.
It is very important to minimize noise at this interface. Excessive noise on
these encoder input signals may result in loss of counts or extra counts and
erroneous closed-loop motion operation. Verify the encoder connections
before powering up the system.
Caution Wire encoder signals and their ground connections separately from all other
connections. Wiring these signals near the motor drive/amplifier or other signals can cause
positioning errors and faulty operation.
Encoders with differential line driver outputs are strongly recommended
for all applications and must be used if the encoder cable length is longer
than 3.05 m (10 ft). Shielded, 24 AWG wire is the minimum recommended
size for the encoder cable. Cables with twisted pairs and an overall shield
are recommended for optimized noise immunity.
All National Instruments power drives and UMI accessories provide
built-in circuitry that converts differential encoder signals to single-ended
encoder signals.
Caution Unshielded cable can cause noise to corrupt the encoder signals, resulting in lost
counts and reduced motion system accuracy.
Encoder Input Circuit
Figure 5-4 shows a simplified schematic diagram of the circuit used for
the Phase A, Phase B, and Index encoder inputs. Both phases A and B are
required for proper encoder counter operation, and the signals must support
the 90° phase difference within system tolerance. The encoder and Index
signals are conditioned by a software-programmable digital filter inside
the FPGA. The Index signal is optional but highly recommended and
required for initialization functionality with the Find Index function.
© National Instruments Corporation
5-9
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Vcc
To the quadrature
decoder circuit
3.3 kΩ
74FCT244
1 kΩ
1/8 W
From the external
connector
encoder input
pins
DGND
Figure 5-4. Encoder Input Circuit
Trigger Inputs, Shutdown Input, and Breakpoint Outputs
The 7340 offers additional high-performance features in the encoder
FPGA. The encoder channels have high-speed position capture trigger
inputs and breakpoint outputs. These signals are useful for high-speed
synchronization of motion with actuators, sensors, and other parts of the
complete motion system:
•
Trigger Input <1..4>—When enabled, an active transition on a
high-speed position capture input causes instantaneous position
capture of the corresponding encoder count value. You can use this
high-speed position capture functionality for applications ranging
from simple position tagging of sensor data to complex camming
systems with advance/retard positioning and registration. An available
7340 position mode is to move an axis Relative to Captured Position.
The polarity of the trigger input is programmable in software as
active-low (inverting) or active-high (non-inverting), rising or falling
edge. You also can use a trigger input as a latching general-purpose
digital input by simply ignoring the captured position.
•
•
Shutdown Input—When enabled in software, the shutdown input
signal can be used to kill all motion by asserting the controller inhibits,
setting the analog outputs to 0 V, and stopping any stepper pulse
generation. To activate shutdown, the signal must transition from a low
to a high state, or rising edge.
Breakpoint Output <1..4>—A breakpoint output can be programmed
to transition when the associated encoder value equals the breakpoint
position. You can use a breakpoint output to directly control actuators
or as a trigger to synchronize data acquisition or other functions in the
motion control system.
NI 7340 User Manual
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Chapter 5
Signal Connections
You can program breakpoints as absolute, modulo, or relative
positions. Breakpoint outputs can be preset to a known state so that the
transition when the breakpoint occurs can be low to high, high to low,
or toggle.
The breakpoint outputs are driven by open-collector TTL buffers that
feature 64 mA sink current capability and built-in 3.3 kΩ pull-up
resistors to +5 V.
You can directly set and reset breakpoint outputs to use them as
general-purpose digital outputs.
Wiring Concerns
Caution Keep trigger input, shutdown input, and breakpoint output signals and their
ground connections wired separately from the motor driver/amplifier signal and encoder
signal connections. Wiring these signals near each other can cause faulty operation.
failure.
Trigger Input, Shutdown Input, and Breakpoint
Output Circuits
Figures 5-5, 5-6, and 5-7 show a simplified schematic diagram of the
circuits used by the trigger inputs, shutdown inputs, and breakpoint outputs
for signal buffering.
Vcc
To the trigger
circuits
3.3 kΩ
74FCT244
1 kΩ
1/8 W
From the external
connector
trigger pins
DGND
Figure 5-5. Trigger Input Circuit
© National Instruments Corporation
5-11
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Vcc
To the shutdown
circuits
3.3 kΩ
74FCT244
1 kΩ
1/8 W
From the external
connector
shutdown pin
DGND
Figure 5-6. Shutdown Input Circuit
Vcc
3.3 kΩ
74AS760
To the external
connector
breakpoint pins
From the
breakpoint
circuits
Figure 5-7. Breakpoint Output Circuit
Analog Inputs
The 7340 has the following ADC input signals:
Analog Input <1..4>—The 7340 includes an eight-channel
•
multiplexed, 12-bit ADC capable of measuring 10 V, 5 V, 0–10 V,
and 0–5 V inputs. ADC channels 1 through 4 are brought out
externally on the 68-pin motion I/O connector. ADC channels 5
through 8 are connected internally, as shown in Table 5-2. These
signals can be used for ADC test and system diagnostics.
Table 5-2. Internal ADC Channels
ADC Input
Signal
5
6
7
8
Filtered +5 V
Floating (NC)
Analog Reference (7.5 V)
Analog Input Ground
NI 7340 User Manual
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Chapter 5
Signal Connections
You can configure each ADC channel for motion feedback, simple
A/D conversion, or both.
You can read the digital value of analog voltage on any of the eight
ADC channels of the controller. Table 5-3 shows the range of values
read back and the voltage resolution for each setting. The voltage
resolution is in volts per least significant bit (V/LSB).
Table 5-3. Analog Input Voltage Ranges
Input Range
10 V
Binary Values
–2,048 to 2,047
–2,048 to 2,047
0 to 4,095
Resolution
0.0049 V/LSB
0.0024 V/LSB
0.0024 V/LSB
0.0012 V/LSB
5 V
0–10 V
0–5 V
0 to 4,095
As indicated in Figure 5-3, when configured as analog feedback, an
analog sensor acts like a limited range absolute position device with a
full-scale position range. You can map any ADC channel as feedback
to any axis.
You can enable and disable individual ADC channels in software.
Disable unused ADC channels for the highest multiplexer scan rate
performance. Properly enabled, the scan rate is high enough to support
analog feedback at the highest PID sample rate.
•
•
Analog Reference—For convenience, 7.5 V (nominal) analog
reference voltage is available. You can use this output as a low-current
supply to sensors that require a stable reference. Refer to Appendix A,
Specifications, for analog reference voltage specifications.
Analog Input Ground—To help keep digital noise out of the analog
input, a separate return connection is available. Use this reference
ground connection and not Digital Ground (digital I/O reference) or
Analog Output Ground as the reference for the analog inputs.
Wiring Concerns
For proper use of each ADC input channel, the analog signal to be
measured should be connected to the channel input and its ground reference
connected to the Analog Input Ground.
external reference voltage. Connect the common of the external reference to the Analog
Input Ground pin for proper A/D reference and improved voltage measurement.
© National Instruments Corporation
5-13
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Other Motion I/O Connection
The 7340 provides Host +5 V, which is the internal +5 V supply of the host
computer. It is typically used to detect when the host computer is powered
and to shut down external motion system components when the host
computer is turned off or disconnected from the motion accessory.
Caution The host +5 V signal is limited to <100 mA and should not be used to power any
external devices, except those intended in the host bus monitor circuits on the UMI and
drive products.
NI 7340 User Manual
5-14
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
Digital I/O Connector
All the general-purpose digital I/O lines on the 7340 are available on a
separate 68-pin digital I/O connector. Figure 5-8 shows the pin
assignments for this connector.
1
2
3
4
5
6
7
8
9
35
36
37
38
39
40
41
42
43
+5 V
PCLK
Digital Ground
Digital Ground
Digital Ground
DPull
Reserved
Reserved
PWM1
Digital Ground
Reserved
Reserved
Reserved
Reserved
PWM2
Digital Ground
Digital Ground
Digital Ground
Port 1:bit 1
Port 1:bit 0
10 44
Digital Ground 11 45
Port 1:bit 3 12 46
Port 1:bit 2
Digital Ground
Port 1:bit 5
13 47
14 48
15 49
16 50
17 51
18 52
19 53
20 54
Port 1:bit 4
Port 1:bit 6
Digital Ground
Port 1:bit 7
Digital Ground
Digital Ground
Port 2:bit 2
Port 2:bit 0
Port 2:bit 1
Digital Ground
Digital Ground
Digital Ground
Port 2:bit 3
Port 2:bit 4
Port 2:bit 5
Port 2:bit 6 21 55
Port 2:bit 7 22 56
Port 3:bit 0 23 57
Digital Ground
Digital Ground
Port 3:bit 1
Digital Ground
Port 3:bit 3
24 58
25 59
Port 3:bit 2
Digital Ground
Port 3:bit 5
Port 3:bit 4 26 60
Digital Ground
Port 3:bit 7 28 62
Port 4:bit 0
Digital Ground 30 64
Port 4:bit 3
27 61
Port 3:bit 6
Digital Ground
Port 4:bit 1
29 63
Port 4:bit 2
31 65
Digital Ground
Port 4:bit 5
Port 4:bit 4 32 66
Digital Ground 33 67
Port 4:bit 7 34 68
Port 4:bit 6
Digital Ground
Figure 5-8. 68-Pin Digital I/O Connector Pin Assignments
© National Instruments Corporation
5-15
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
The 32-bit digital I/O port is configured in hardware as four 8-bit digital I/O
ports. The bits in a port are typically controlled and read with byte-wide
bitmapped commands.
All digital I/O lines have programmable direction and polarity. Each output
circuit can sink and source 24 mA.
The DPull pin controls the state of the input pins at power-up. Connecting
DPull to +5 V or leaving it unconnected configures all pins in all ports for
100 kΩ pull-ups. Connecting DPull to ground configures the ports for
100 kΩ pull-downs.
PWM Features
The 7340 provides two pulse width modulation (PWM) outputs on the
digital I/O connector. The PWM outputs generate periodic waveforms
whose period and duty cycles can be independently controlled through
software commands. The PWM is comparable to a digital representation of
an analog value because the duty cycle is directly proportional to the
expected output value. PWM outputs are typically used for transmitting an
analog value through an optocoupler. A simple lowpass filter turns a PWM
signal back into its corresponding analog value. You have the option to use
the PCLK input instead of the internal source as the clock for the PWM
generators.
Note These signals are configured in software and are in no way associated with the
PID servo control loop. Refer to the NI-Motion User Manual for more information.
RTSI Connector
The physical RTSI bus interface varies depending on the type of 7340
controller.
The PXI-7340 uses the PXI chassis backplane to connect to other
RTSI-capable devices.
The PCI-7340 uses a ribbon cable to connect to other RTSI-capable PCI
devices.
NI 7340 User Manual
5-16
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Signal Connections
RTSI Signal Considerations
The 7340 motion controller allows you to use up to eight RTSI trigger lines
as sources for trigger inputs, or as destinations for breakpoint outputs and
encoder signals. The RTSI trigger lines also can serve as a generic digital
I/O port. The RTSI star trigger line can be used only for a trigger input.
Breakpoint outputs are output-only signals that generate an active-high
pulse of 200 ns duration, as shown in Figure 5-9.
200 ns
Figure 5-9. Breakpoint across RTSI
Encoder and Index signals are output-only signals across RTSI that are
the digitally-filtered versions of the raw signals coming into the controller.
If you are using the RTSI bus for trigger inputs or generic digital I/O,
all signals are passed through unaltered.
© National Instruments Corporation
5-17
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
This appendix lists the hardware and software performance specifications
for the PXI/PCI-7340. Hardware specifications are typical at 25 °C, unless
otherwise stated.
Servo Performance
PID update rate range............................. 62.5 µs to 5 ms/sample
Maximum PID update rate.............. 62.5 µs/axis
4-axis PID update rate..................... 250 µs total
Multi-axis synchronization .................... <1 update sample
Position accuracy
Encoder feedback............................ 1 quadrature count
Analog feedback ............................. 1 LSB
Double-buffered trajectory parameters
Absolute position range .................. 231 counts
Maximum relative move size.......... 231 counts
Velocity range................................. 1 to 20,000,000 counts/s
Acceleration/deceleration1 .............. 512,000,000 counts/s2
S-Curve time range ......................... 1 to 32,767 samples
Following error range ..................... 1 to 32,767 counts and disabled
Gear ratio ........................................ 32,767:1 to 1:32,767
Servo control loop modes ...................... PID, PIVff, S-Curve, Dual Loop
PID (Kp, Ki, and Kd) gains ............ 0 to 32,767
Integration limit (Ilim).................... 0 to 32,767
Derivative sample period (Td)........ 1 to 63 samples
Feedforward (Aff, Vff) gains.......... 0 to 32,767
Velocity feedback (Kv) gain........... 0 to 32,767
1
Assumes a PID update rate of 250 µs and a 2,000-count encoder.
© National Instruments Corporation
A-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Servo command analog outputs
Voltage range................................... 10 V
Resolution........................................16 bits (0.000305 V/LSB)
Programmable torque (velocity) limits
Positive limit ............................ 10 V (–32,768 to +32,767)
Negative limit........................... 10 V (–32,768 to +32,767)
Programmable offset ....................... 10 V (–32,768 to +32,767)
Stepper Performance
Trajectory update rate range...................62.5 to 500 µs/sample
Maximum update rate......................62.5 µs/axis
4-axis update rate.............................250 µs total
Multi-axis synchronization.....................<1 update sample
Position accuracy
Open-loop stepper ...........................1 full, half, or microstep
Encoder feedback ............................ 1 quadrature count
Analog feedback.............................. 1 LSB
Double-buffered trajectory parameters
Position range.................................. 231 steps
Maximum relative move size .......... 231 steps
Velocity range .................................1 to 4,000,000 steps/s
Acceleration/deceleration1............... 512,000,000 counts/s2
S-Curve time range..........................1 to 32,767 samples
Following error range......................0 to 32,767 counts
Gear ratio......................................... 32,767:1 to 1:32,767
Stepper outputs
Maximum pulse rate........................4 MHz (full, half, and microstep)
Minimum pulse width......................120 ns at 4 MHz
Step output mode.............................Step and direction or CW/CCW
1
Assumes a PID update rate of 250 µs and a 2,000-count encoder.
NI 7340 User Manual
A-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Voltage range.................................. 0 to 5 V
Output low voltage .................. <0.6 V at 64 mA sink
Output high voltage ................. Open collector with built-in
3.3 kΩ pull-up to +5 V
Polarity............................................ Programmable, active-high
or active-low
System Safety
Watchdog timer function ....................... Resets board to startup state
Watchdog timeout........................... 63 ms
Shutdown input
Voltage range.................................. 0 to 5 V
Input low voltage..................... 0.8 V
Input high voltage.................... 2 V
Polarity..................................... Rising edge
Control ............................................ Disable all axes and
command outputs
Motion I/O
Encoder inputs........................................ Quadrature, incremental,
single-ended
Maximum count rate....................... 20 MHz
Minimum pulse width..................... Programmable; depends
on digital filter settings
Voltage range.................................. 0 to 5 V
Input low voltage..................... 0.8 V
Input high voltage.................... 2 V
Minimum index pulse width........... Programmable; depends
on digital filter settings
Forward, reverse, and home inputs
Number of inputs ............................ 12 (3 per axis)
Voltage range.................................. 0 to 5 V
Input low voltage..................... 0.8 V
Input high voltage.................... 2 V
Polarity............................................ Programmable, active-high
or active-low
© National Instruments Corporation
A-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Minimum pulse width......................1 ms with filter enabled;
60 ns without filter enabled
Control.............................................Individual enable/disable, stop on
input, prevent motion, Find Home
Trigger inputs
Number of inputs.............................4 (Encoders 1 through 4)
Voltage range...................................0 to 5 V
Input low voltage......................0.8 V
Input high voltage.....................2 V
Polarity ............................................Programmable, active-high
or active-low
Minimum pulse width......................100 ns
Capture latency................................<100 ns
Capture accuracy .............................1 count
Maximum repetitive capture rate.....100 Hz
Breakpoint outputs
Number of outputs...........................4 (Encoders 1 through 4)
Voltage range...................................0 to 5 V
Output low voltage...................<0.6 V at 64 mA sink
Output high voltage..................Open collector with built-in
3.3 kΩ pull-up to +5 V
Polarity ............................................Programmable, active-high
or active-low
Maximum repetitive
breakpoint rate.................................100 Hz
Inhibit/enable output
Number of outputs...........................4 (1 per-axis)
Voltage range...................................0 to 5 V
Output low voltage...................<0.6 V at 64 mA sink
Output high voltage..................Open collector with built-in
3.3 kΩ pull-up to +5 V
Polarity ............................................Programmable, active-high
or active-low
Control.............................................MustOn/MustOff or
automatic when axis off
NI 7340 User Manual
A-4
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Analog inputs
Number of inputs ............................ 8, multiplexed, single ended
Number for user signals........... 4
Number for system diagnostics... 4
Voltage range (programmable)....... 10 V, 5 V, 0–10 V, 0–5 V
Input coupling................................. DC
Input resistance ............................... 10 kΩ min
Resolution ....................................... 12 bits, no missing codes
Monotonic....................................... Guaranteed
Multiplexor scan rate ...................... 25 µs/enabled channel
Analog outputs
Number of outputs .......................... 4, single ended
Output coupling .............................. DC
Voltage range.................................. 10 V
Output current................................. 5 mA
Resolution ....................................... 16 bits, no missing codes
Monotonic....................................... Guaranteed
Analog reference output.................. 7.5 V (nominal) @ 5 mA
Digital I/O
Ports ....................................................... 4, 8-bit ports
Line direction.................................. Individual bit programmable
Inputs
Voltage range.................................. 0 to 5 V
Input low voltage..................... 0.8 V
Input high voltage.................... 2.0 V
Polarity............................................ Programmable, active-high
or active-low
Outputs
Voltage range.................................. 0 to 5 V
Output low voltage .................. <0.45 V at 24 mA sink
Output high voltage ................. >2.4 V at 24 mA source
Polarity............................................ Programmable, active-high
or active-low
© National Instruments Corporation
A-5
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
PWM outputs
Number of PWM outputs.........2
Maximum PWM frequency......50 kHz
Resolution.................................8-bit
Duty cycle range.......................0 to (255/256)%
Clock sources ...........................Internal or external
RTSI
Trigger lines............................................8
Maximum Power Requirements
+5 V ( 3%).............................................1 A
+12 V ( 3%)...........................................30 mA
–12 V ( 3%) ...........................................30 mA
Power consumption ................................5.7 W
Physical
Dimensions (Not Including Connectors)
PXI-7340 ................................................16 × 10 cm (6.3 × 3.9 in.)
PCI-7340.................................................17.5 × 9.9 cm (6.9 × 3.9 in.)
Connectors
Motion I/O connector .............................68-pin female high-density
VHDCI type
32-bit digital I/O connector ....................68-pin female high-density
VHDCI type
Weight
PXI-7340 ................................................170 g (6 oz)
PCI-7340.................................................113 g (4 oz)
NI 7340 User Manual
A-6
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Maximum Working Voltage
Channel-to-earth..................................... 12 V, Installation Category I
(signal voltage plus
common-mode voltage)
Channel-to-channel ................................ 22 V, Installation Category I
(signal voltage plus
common-mode voltage)
Caution These values represent the maximum allowable voltage between any accessible
signals on the controller. To determine the acceptable voltage range for a particular signal,
refer to the individual signal specifications.
Environment
Operating temperature............................ 0 to 55 °C
Storage temperature ............................... –20 to 70 °C
Humidity ................................................ 10 to 90% RH, noncondensing
Maximum altitude.................................. 2,000 m
Pollution Degree .................................... 2
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
•
•
•
IEC 61010-1, EN 61010-1
UL 3111-1, UL 61010B-1
CAN/CSA C22.2 No. 1010.1
Note For UL and other safety certifications, refer to the product label, or visit
ni.com/hardref.nsf, search by model number or product line, and click the
appropriate link in the Certification column.
© National Instruments Corporation
A-7
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
Electromagnetic Compatibility
Emissions................................................EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Immunity ................................................EN 61326:1997 + A2:2001,
Table 1
EMC/EMI ...............................................CE, C-Tick, and FCC Part 15
(Class A) Compliant
Note For EMC compliance, you must operate this device with shielded cabling.
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:
Low-Voltage Directive (safety)..............73/23/EEC
Electromagnetic Compatibility
Directive (EMC).....................................89/336/EEC
Note Refer to the Declaration of Conformity (DoC) for this product for any additional
regulatory compliance information. To obtain the DoC for this product, visit
ni.com/hardref.nsf, search by model number or product line, and click the
appropriate link in the Certification column.
NI 7340 User Manual
A-8
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
B
This appendix describes the connector pinout for the cables that connect
to the PXI/PCI-7340.
Figures B-1 and B-2 show the pin assignments for the stepper and servo
50-pin motion connectors. These connectors are available when you use
the SH68-C68-S shielded cable assembly and the 68M-50F step/servo
bulkhead cable adapter.
1
3
5
7
9
2
4
Axis 1 Dir (CCW)
Digital Ground
Digital Ground
Axis 1 Step (CW)
Axis 1 Encoder Phase A
Axis 1 Encoder Phase B
Axis 1 Encoder Index
Axis 1 Forward Limit Switch
Axis 1 Reverse Limit Switch
Axis 2 Step (CW)
6
8
Axis 1 Home Switch
Trigger/Breakpoint 1
Axis 1 Inhibit
10
11 12
13 14
15 16
Axis 2 Dir (CCW)
Digital Ground
Axis 2 Encoder Phase A
17 18 Axis 2 Encoder Phase B
Digital Ground
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
Axis 2 Encoder Index
Axis 2 Forward Limit Switch
Axis 2 Reverse Limit Switch
Axis 3 Step (CW)
Axis 2 Home Switch
Trigger/Breakpoint 2
Axis 2 Inhibit
Axis 3 Dir (CCW)
Digital Ground
Axis 3 Encoder Phase A
Axis 3 Encoder Phase B
Axis 3 Encoder Index
Axis 3 Forward Limit Switch
Axis 3 Reverse Limit Switch
Axis 4 Step (CW)
Digital Ground
Axis 3 Home Switch
Trigger/Breakpoint 3
Axis 3 Inhibit 35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
Axis 4 Dir (CCW)
Digital Ground
Axis 4 Encoder Phase A
Axis 4 Encoder Phase B
Axis 4 Encoder Index
Axis 4 Forward Limit Switch
Axis 4 Reverse Limit Switch
Host +5 V
Digital Ground
Axis 4 Home Switch
Trigger/Breakpoint 4
Axis 4 Inhibit
Digital Ground
Figure B-1. 50-Pin Stepper Connector Pin Assignment
© National Instruments Corporation
B-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Cable Connector Descriptions
1
3
5
7
9
2
4
Analog Output Ground
Digital Ground
Analog Output 1
Axis 1 Encoder Phase A
Axis 1 Encoder Phase B
Axis 1 Encoder Index
Axis 1 Forward Limit Switch
Axis 1 Reverse Limit Switch
Analog Output 2
6
Digital Ground
8
Axis 1 Home Switch
Trigger/Breakpoint 1
Axis 1 Inhibit
10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
Analog Output Ground
Digital Ground
Axis 2 Encoder Phase A
Axis 2 Encoder Phase B
Axis 2 Encoder Index
Axis 2 Forward Limit Switch
Axis 2 Reverse Limit Switch
Analog Output 3
Digital Ground
Axis 2 Home Switch
Trigger/Breakpoint 2
Axis 2 Inhibit
Analog Output Ground
Digital Ground
Axis 3 Encoder Phase A
Axis 3 Encoder Phase B
Axis 3 Encoder Index
Axis 3 Forward Limit Switch
Axis 3 Reverse Limit Switch
Analog Output 4
Digital Ground
Axis 3 Home Switch
Trigger/Breakpoint 3
Axis 3 Inhibit
Analog Output Ground
Digital Ground
Axis 4 Encoder Phase A
Axis 4 Encoder Phase B
Axis 4 Encoder Index
Axis 4 Forward Limit Switch
Axis 4 Reverse Limit Switch
Host +5 V
Digital Ground
Axis 4 Home Switch
Trigger/Breakpoint 4
Axis 4 Inhibit
Digital Ground
Figure B-2. 50-Pin Servo Connector Pin Assignment
NI 7340 User Manual
B-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
C
Technical Support and
Professional Services
Visit the following sections of the National Instruments Web site at
ni.comfor technical support and professional services:
•
Support—Online technical support resources include the following:
–
Self-Help Resources—For immediate answers and solutions,
visit our extensive library of technical support resources available
in English, Japanese, and Spanish at ni.com/support. These
resources are available for most products at no cost to registered
users and include software drivers and updates, a KnowledgeBase,
product manuals, step-by-step troubleshooting wizards,
conformity documentation, example code, tutorials and
application notes, instrument drivers, discussion forums,
a measurement glossary, and so on.
–
Assisted Support Options—Contact NI engineers and other
measurement and automation professionals by visiting
ni.com/support. Our online system helps you define your
question and connects you to the experts by phone, discussion
forum, or email.
•
•
Training—Visit ni.com/trainingfor self-paced tutorials, videos,
and interactive CDs. You also can register for instructor-led, hands-on
courses at locations around the world.
System Integration—If you have time constraints, limited in-house
technical resources, or other project challenges, NI Alliance Program
members can help. To learn more, call your local NI office or visit
ni.com/alliance.
•
Declaration of Conformity (DoC)—A DoC is our claim of
compliance with the Council of the European Communities using
the manufacturer’s declaration of conformity. This system affords
the user protection for electronic compatibility (EMC) and product
safety. You can obtain the DoC for your product by visiting
ni.com/hardref.nsf.
© National Instruments Corporation
C-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Technical Support and Professional Services
If you searched ni.comand could not find the answers you need, contact
your local office or NI corporate headquarters. Phone numbers for our
worldwide offices are listed at the front of this manual. You also can visit
the Worldwide Offices section of ni.com/niglobalto access the branch
office Web sites, which provide up-to-date contact information, support
phone numbers, email addresses, and current events.
NI 7340 User Manual
C-2
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Symbol
Prefix
micro
milli
Value
10– 6
10–3
106
µ
m
M
mega
Numbers/Symbols
/
per
plus or minus
+
positive of, or plus
negative of, or minus
–
+5 V
+5 VDC source signal
A
A
amperes
A/D
analog-to-digital
absolute mode
treat the target position loaded as position relative to zero (0) while making
a move
absolute position
position relative to zero
acceleration/
deceleration
measurement of the change in velocity as a function of time. Acceleration
and deceleration describes the period when velocity is changing from one
value to another.
active-high
active-low
ADC
signal is active when its value goes high (1)
signal is active when its value goes low (0)
analog-to-digital converter
© National Instruments Corporation
G-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
address
character code that identifies a specific location (or series of locations)
in memory or on a host PC bus system
amplifier
drive that delivers power to operate the motor in response to low level
control signals. In general, the amplifier is designed to operate with a
particular motor type—for example, you cannot use a stepper drive to
operate a DC brush motor
Analog Input <1..4>
12-bit analog ADC input
Analog Output <1..4>
16-bit DAC voltage output
API
axis
application programming interface
unit that controls a motor or any similar motion or control device
axis 1 through 4 forward/clockwise limit switch
Axis <1..4> Forward
Limit Input
Axis <1..4> Home
Input
axis 1 through 4 home input
Axis <1..4> Inhibit
axis 1 through 4 inhibit output
Axis <1..4> Reverse
Limit Input
axis 1 through 4 reverse/counter-clockwise limit input
B
b
bit—one binary digit, either 0 or 1
base address
memory address that serves as the starting address for programmable or
I/O bus registers. All other addresses are located by adding to the base
address.
binary
buffer
bus
number system with a base of 2
temporary storage for acquired or generated data (software)
group of conductors that interconnect individual circuitry in a computer.
Typically, a bus is the expansion vehicle to which I/O or other devices are
NI 7340 User Manual
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Glossary
byte
eight related bits of data, an eight-bit binary number. Also used to denote
the amount of memory required to store one byte of data.
C
CCW
counter-clockwise—implies direction of rotation of the motor
closed-loop
motion system that uses a feedback device to provide position and velocity
data for status reporting and accurately controlling position and velocity
common
CPU
reference signal for digital I/O
central processing unit
crosstalk
CSR
unwanted signal on one channel due to an input on a different channel
Communications Status Register
CW
clockwise—implies direction of motor rotation
D
D/A
digital-to-analog
DAC
Digital-to-Analog Converter
direct current
DC
dedicated
DGND
digital I/O port
DIP
assigned to a particular function
digital ground signal
group of digital input/output signals
dual inline package
DLL
dynamic link library—provides the API for the motion control boards
drivers
software that communicates commands to control a specific motion control
board
DSP
Digital Signal Processor
© National Instruments Corporation
G-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
E
encoder
device that translates mechanical motion into electrical signals; used for
monitoring position or velocity in a closed-loop system
encoder resolution
number of encoder lines between consecutive encoder indexes (marker or
Z-bit). If the encoder does not have an index output, the encoder resolution
can be referred to as lines per revolution.
F
f
farad
FIFO
first in, first out—data buffering technique that functions like a shift register
where the oldest values (first in) come out first
filter parameters
filtering
indicates the control loop parameter gains (PID gains) for a given axis
type of signal conditioning that filters unwanted signals from the signal
being measured
flash ROM
type of electrically reprogrammable read-only memory
following error
trip point
difference between the instantaneous commanded trajectory position and
the feedback position
FPGA
Field Programmable Gate Array
freewheel
condition of a motor when power is de-energized and the motor shaft is free
to turn with only frictional forces to impede it
full-step
full-step mode of a stepper motor—for a two phase motor this is done by
energizing both windings or phases simultaneously
G
Gnd
ground
ground
GND
NI 7340 User Manual
G-4
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
H
half-step
mode of a stepper motor—for a two phase motor this is done by alternately
energizing two windings and then only one. In half step mode, alternate
steps are strong and weak but there is significant improvement in low-speed
smoothness over the full-step mode.
hex
hexadecimal
home switch (input)
physical position determined by the mechanical system or designer as the
reference location for system initialization. Frequently, the home position is
also regarded as the zero position in an absolute position frame of reference.
host computer
computer into which the motion control board is plugged
I
I/O
input/output—the transfer of data to and from a computer system involving
communications channels, operator interface devices, and/or motion
control interfaces
ID
identification
in.
inches
index
inverting
marker between consecutive encoder revolutions
polarity of a switch (limit switch, home switch, and so on) in active state.
If these switches are active-low they are said to have inverting polarity.
IRQ
interrupt request
K
k
kilo—the standard metric prefix for 1,000, or 103, used with units of
measure such as volts, hertz, and meters
K
kilo—the prefix for 1,024, or 210, used with B in quantifying data or
computer memory
© National Instruments Corporation
G-5
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
L
LIFO
last in, last out—data buffering technique where the newest values (last in)
come out first
limit switch/
end-of-travel position
(input)
sensors that alert the control electronics that physical end of travel is being
approached and that the motion should stop
M
m
meters
MCS
microstep
Move Complete Status
proportional control of energy in the coils of a Stepper Motor that
allows the motor to move to or stop at locations other than the fixed
magnetic/mechanical pole positions determined by the motor
specifications. This capability facilitates the subdivision of full mechanical
steps on a stepper motor into finer microstep locations that greatly smooth
motor running operation and increase the resolution or number of discrete
positions that a stepper motor can attain in each revolution.
modulo position
treat the position as within the range of total quadrature counts per
revolution for an axis
N
noise
undesirable electrical signal—noise comes from external sources such as
the AC power line, motors, generators, transformers, fluorescent lights,
soldering irons, CRT displays, computers, electrical storms, welders, radio
transmitters, and internal sources such as semiconductors, resistors, and
capacitors. Noise corrupts signals you are trying to send or receive.
noninverting
polarity of a switch (limit switch, home switch, and so on) in active state.
If these switches are active-high, they are said to have non-inverting
polarity.
NI 7340 User Manual
G-6
ni.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
O
open-loop
refers to a motion control system where no external sensors (feedback
devices) are used to provide position or velocity correction signals
P
PCI
Peripheral Component Interconnect—a high-performance expansion bus
architecture originally developed by Intel to replace ISA and EISA. It is
achieving widespread acceptance as a standard for PCs and workstations;
it offers a theoretical maximum transfer rate of 132 MB/s.
PID
proportional-integral-derivative control loop
proportional-integral-velocity feed forward
PIVff
port
(1) a communications connection on a computer or a remote controller;
(2) a digital port, which consists of eight lines of digital input and/or output
position breakpoint
position breakpoint for an encoder can be set in absolute or relative
quadrature counts. When the encoder reaches a position breakpoint,
the associated breakpoint output immediately transitions.
power cycling
PWM
turning the host computer off and then back on, which causes a reset of
the motion control board
Pulse Width Modulation—a method of controlling the average current in
a motor phase winding by varying the on-time (duty cycle) of transistor
switches
PXI
PCI eXtensions for Instrumentation
Q
quadrature counts
encoder line resolution times four
R
RAM
random-access memory
relative breakpoint
sets the position breakpoint for an encoder in relative quadrature counts
© National Instruments Corporation
G-7
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
relative position
destination or target position for motion specified with respect to the
current location regardless of its value
relative position mode
ribbon cable
RPM
position relative to current position
flat cable in which the conductors are side by side
revolutions per minute—units for velocity
revolutions per second squared—units for acceleration and deceleration
Ready to Receive
RPSPS or RPS/S
RTR
S
s
seconds
servo
stepper
specifies an axis that controls a servo motor
specifies an axis that controls a stepper motor
direction output or counter-clockwise direction control
stepper <1..4>
Dir (CCW)
stepper <1..4>
Step (CW)
stepper pulse output or clockwise direction control
T
toggle
changing state from high to low, back to high, and so on
force tending to produce rotation
torque
trapezoidal profile
typical motion trajectory, where a motor accelerates up to the programmed
velocity using the programmed acceleration, traverses at the programmed
velocity, then decelerates at the programmed acceleration to the target
position
trigger
TTL
any event that causes or starts some form of data capture
transistor-transistor logic
NI 7340 User Manual
G-8
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Glossary
V
V
volts
VCC
positive voltage supply
velocity mode
move the axis continuously at the specified velocity
W
watchdog
timer task that shuts down (resets) the motion control board if any serious
error occurs
word
standard number of bits that a processor or memory manipulates at
one time, typically 8-, 16-, or 32-bit
© National Instruments Corporation
G-9
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
68-pin
Analog Input <1..4>, 5-12
Analog Input Ground, 5-13
Analog Output <1..4>, 5-4
Analog Output Ground, 5-4
Analog Reference, 5-13
analog signals, wiring, 5-13
axes, 4-3
digital I/O connector, 3-3
motion I/O connector, 3-3
7340
analog feedback, 4-2
axes, 4-3
breakpoint outputs, 5-10
configuring, 2-1
secondary
embedded operating system, 4-2
encoder signals, 5-7
features, 1-1
feedback resources, 4-4
output resources, 4-4
Axis <1..4>
flash memory, 4-3
general-purpose digital I/O lines, 5-15
hardware, 1-1
Forward Limit Input, 5-5
Home Input, 5-5
Inhibit, 5-5
architecture, 4-1
home inputs, 5-5
Reverse Limit Input, 5-5
input and output signal connections, 5-1
installing software, 2-1
introduction, 1-1
limit inputs, 5-5
concepts, 4-5
motion
examples, 5-17
breakpoint output
circuit, 5-12
I/O connections, 1-4
signals, wiring, 5-11
Breakpoint Output <1..4>, 5-10
buffers, 4-5
National Instruments application
software, 1-3
pulse width modulation (PWM)
outputs, 5-16
shutdown input, 5-10
software programming choices, 1-3
trajectory generators, 4-2
trigger inputs, 5-10
user connectors, 3-3
using RTSI, 1-2
command buffer, 4-5
communications status register (CSR), 4-5
communications, host, 4-5
connectors
68-pin
digital I/O, 3-3, 5-1
© National Instruments Corporation
I-1
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
motion I/O, 3-3, 5-1
motion I/O, 5-1
H
help, technical support, C-1
high-speed capture, 4-5
home inputs
conventions used in the manual, vii
circuit, 5-7
ground connections, 5-6
D
Declaration of Conformity (NI resources), C-1
diagnostic tools (NI resources), C-1
documentation
conventions used in manual, vii
NI resources, C-1
drivers (NI resources), C-1
I
installing
hardware, 2-4
installation category descriptions, 2-3
software, 2-1
instrument drivers (NI resources), C-1
E
Encoder <1..4>
Index, 5-8
Phase A/Phase B, 5-7
encoder signals
K
KnowledgeBase, C-1
ground connections, 5-9
examples (NI resources), C-1
limit input circuit, 5-7
limit inputs, ground connections, 5-6
F
functional overview
buffers, 4-5
M
host communications, 4-5
onboard programs, 4-5
memory, buffer storage, 4-5
motion I/O
connector
G
ground connections
encoder signals, 5-9
wiring
N
breakpoint outputs, 5-11
shutdown input, 5-11
National Instruments support and
services, C-1
NI support and services, C-1
NI 7340 User Manual
I-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ni.com
Index
O
onboard programs, 4-5
training (NI resources), C-1
Trigger Input <1..4>, 5-10
trigger input circuit, 5-11
troubleshooting (NI resources), C-1
P
pin assignments
68-pin digital I/O connector, 5-15
programming examples (NI resources), C-1
R
Web resources, C-1
related documentation, viii
return data buffer (RDB), 4-5
RTSI
wiring, analog signals, 5-13
breakpoint across RTSI (figure), 5-17
connector, 3-3, 5-16
signal considerations, 5-17
S
safety information, 2-1
Shutdown Input, 5-10
software (NI resources), C-1
software, onboard programs, 4-5
support, technical, C-1
© National Instruments Corporation
I-3
NI 7340 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|