Nady Systems Microphone DKW1HTFSYS User Manual

DKW-1 GT OPERATING INSTRUCTIONS  
Congratulations on your purchase. The Nady DKW-1 GT is the perfect entry level professional wireless, and delivers clear, transparent audio for your instrument. Although  
offered at a breakthrough new low price for a professional wireless, this system is loaded with features:  
• High-band VHF (170-216 MHz) operation for interference-free performance  
• Full frequency response from 40 –20,000 Hz  
• 250 ft. typical, up to 500 ft. line-of-sight operating range  
• DKW-1receiver with unique vertical space-saving mini portable design and jumbo LED indicators for power ON, transmitter ON and audio peak. Special  
added circuitry eliminates transmitter ON/OFF"pop" noise.  
• All the advantages of wireless operation without cumbersome cords  
• Easy to use — simply plug in instead of your cord  
• Excellent high fidelity and dynamic range —perfect for wireless guitar, bass, and other instruments with pickups  
OPERATION  
A. DKW-1 RECEIVER  
1. Plug the AC/DC adapter (provided) into the 12VDC INPUT JACK (3) on the back  
of the receiver. Then plug the power supply into an AC outlet. Slide the POWER  
SWITCH (1) to the ON position. The POWER ON LED (6) will now light and the  
7
receiver is operational.  
DKW-1  
2. Rotate and extend ANTENNA (7) to the full vertical position.  
4
5
3. The 1/4” AUDIO OUTPUT JACK (2) provides a fixed, unbalanced MIC level  
audio output for connection to your mixer with the 3 ft. 1/4” to 1/4” cord  
supplied. As when making any connection, make sure the mixing boards volume is  
at the minimum level before plugging in the receiver to avoid possible sound system  
damage.  
2
3
13  
6
1
B. WGT BODYPACK TRANSMITTER  
12  
1. Snap open the BATTERY COMPARTMENT (8) and insert a fresh alkaline 9V  
BATTERY (9), observing the correct polarity. Close the compartment. The WGT is  
provided with a 3.5 mm LOCKING JACK (13) for connecting the INSTRUMENT  
CABLE (14). To secure the connection, turn the metal slip ring on the plug clockwise  
to thread it on to the jack. To unplug, reverse the process. Slip the transmitter into  
a pocket or clip on to your clothes or instrument strap. (Note: As the cord to the  
instrument also serves as the antenna, be sure to extend it fully for maximum range.  
Rolling up or shortening the cord may reduce the effective operating range.)  
11  
10  
14  
2. Turn on the WGT by sliding the OFF/MUTE/ON SWITCH (10) to the MUTE  
position (transmitter on, audio muted) or the ON position (transmitter and audio  
both on). The BATTERY INDICATOR LED (11) will give a single quick flash,  
indicating usable battery strength. In the case of a dead or low battery, the LED  
either will not go on at all or will stay on continuously, indicating that the battery  
should be replaced with a fresh one.  
8
3. The WGT is now ready to use. The TRANSMITTER SIGNAL RECEIVED LED (5) on  
the DKW-1 receiver should now be lit. When ready to perform, slide the transmitter  
switch to the ON position and adjust the mixing board volume level as needed.  
(Note: Turning down the input gain too much can compromise the signal-to-noise  
ratio and is not recommended. Set for the maximum possible gain and headroom  
without noticeable distortion on the high level peaks).  
9
The AUDIO PEAK LED (4) on the DKW-1 receiver will light up with loud audio.  
Occasional flickering on and off during use of this top red LED indicator display is  
normal, however if the red LED stays on continuously, turn down the instrument  
volume or adjust the INPUT LEVEL CONTROL (12) on the WGT transmitter, or  
noticeable distortion may result.  
Opening Battery  
Compartment  
give you scratchy noises, we suggest these steps to eliminate them:  
1) Make sure all guitar volume and tone pots are clean and all contacts are  
solid this is very important.  
2) Provide extra filtering with a 220 pF capacitor soldered across the hot to  
ground terminals of the guitar's volume and tone pots.)  
(Note: Scratchy noises can sometimes occur when some electric guitars/basses with  
dirty pots or connections are used with any wireless system. For this reason, the  
supplied INSTRUMENT CORD (14) has a factory installed capacitor inside the 1/4"  
plug. This capacitor provides first order filtering of the RF signal from the cord into  
the guitar and eliminates virtually all scratchy noises. Should your equipment still  
SERVICE  
(U.S.) Should your Nady DKW-1 Wireless Microphone System require service, please contact the Nady Customer Service Department via telephone: (510) 652-2411 or  
e-mail: [email protected].  
(INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you purchased this product.  
The warranty card supplied with this system provides valuable warranty and service information. Store it in a safe place for future reference. Do not attempt to  
service this unit yourself as it will void your warranty.  
NADY SYSTEMS, INC.  
6701 Shellmound Street Emeryville, CA 94608 Tel: 510.652.2411 Fax: 510.652.5075 www.nady.com  
© NADY SYSTEMS, INC. 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  

NETGEAR Network Card 24 GHz MA111 User Manual
Niles Audio Speaker CM730DS User Manual
NordicTrack Home Gym 831157180 User Manual
Nortel Networks Switch 8010co User Manual
Optoma Technology Projector HD806 ISF User Manual
Oreck Vacuum Cleaner MODEL AV 701B User Manual
Panasonic Electric Shaver ES2207 User Manual
Panasonic MP3 Player AJ PCS060G User Manual
Panasonic Telephone KX T7720 User Manual
Parrot Automobile Electronics 3100 3300 3500 User Manual