N8406-019/N8406-020
FC スイッチモジュール
ユーザーズガイド
N8406-019/N8406-020
FC Switch Module
User’s Guide
856-083456-010-A
2007年 3月 5版
March 2007, 5th Edition
注意
製品のご使用前に、必ず本書をお読みの上で注意をお守りください。本書は、必要な時にすぐ
見られるように保管してください。
Caution
Read this book without fail before using the product and guard attention.
Keep this book so that it is show soon when it is necessary.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Congratulations on your purchase of FC Switch Modules N8406-019/N8406-020.
The guide is intended to allow you to install and use FC Switch Modules N8406-019/N8406-020 correctly
and safely. Read the guide carefully before treating the FC Switch Modules. Refer to the guide when
you find something unknown on the FC Switch Module or a malfunction occurs. Always keep the guide
so that you can see it immediately if necessary.
For the Blade Enclosure (SIGMABLADE) in which the FC Switch Modules are installed, refer to the User’s
Guideattachedtothe Blade Enclosure(SIGMABLADE). Inaddition, before handingtheFC Switch Modules,
always read "Notes on Safety" and "Notes on Use" in the guide.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
商標について
Microsoft とそのロゴおよび Microsoft Windows, Windows, Windows Server 2003 は米国 Microsoft
Corporationの米国およびその他の国における登録商標です。
記載の会社名および商品名は各社の商標または登録商標です。
Brocadeとそのロゴは米国Brocade Communications Systems, Inc.の米国およびその他の国における登録商
標です。
記載の会社名および商品名は各社の商標または登録商標です。
ご注意
(1) 本書の内容の一部または全部を無断転載することは禁止されています。
(2) 本書の内容に関しては将来予告なしに変更することがあります。
(3) NECの許可なく複製・改変などを行うことはできません。
(4) 本書は内容について万全を期して作成いたしましたが、万一ご不審な点や誤り、記載もれなどお気づきのことが
ありましたら、お買い求めの販売店にご連絡ください。
(5) 運用した結果の影響については(4)項にかかわらず責任を負いかねますのでご了承ください。
このユーザーズガイドは、必要なときすぐに参照できるように必ずお手元に保管してください。
「安全上のご注意」および「使用上のご注意」を必ずお読みください。
電波障害自主規制について
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基づくクラスA情報技術装置で
す。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切
な対策を講ずるよう要求されることがあります。
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Microsoft, its logo, Microsoft Windows, Windows, and Windows Server 2003 are worldwide registered
trademarks of Microsoft Corporation of the U.S.A.
Brocade and its logo are worldwide registered trademarks of Brocade Communications Systems, Inc. of the
U.S.A.
All company names and product names mentioned herein are trademarks or registered trademarks of their
respective companies.
Notes:
(1) No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation.
(2) The contents of this manual may be revised without prior notice.
(3) The contents of this manual shall not be copied or altered without the prior written permission of NEC Corporation.
(4) All efforts have been made to ensure the accuracy of all information in this manual. If you notice any part unclear,
incorrect, or omitted in this manual, contact your service representative.
(5) NEC assumes no liability arising from the use of this product, nor any liability for incidental or consequential
damages arising from the use of this manual regardless of Item (4).
(6) If you find any missing pages or pages out of order in this manual, please contact your service representative for a
replacement.
(7) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Keep this User's Guide at hand for quick reference at anytime necessary.
Be sure to read this section carefully.
CE Statement
Warning: This is a Class A product. In domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures (EN55022).
CANADIAN NOTICE
This Class A digital appatature meets all requirements of the Canadian interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
安全上のご注意 ~ 必ずお読みください ~
本製品を安全に正しくご使用になるために必要な情報が記載されています。
安全にかかわる表示
本書では危険の程度を表す言葉として、「警告」と「注意」という用語を使用しています。それぞれの
用語は次のような意味を持つものとして定義されています。
人が死亡する、または重傷を負うおそれがあることを示します。
警告
火傷や怪我などを負うおそれや物的損害を負うおそれがあることを示します。
注意
表示は次の3種類の記号を使って表します。それぞれの記号は次のような意味を持つものものとし
て定義されています。
(例)
この記号は危険が発生するおそれがあることを表します。記号
注意の喚起
の中の絵表示は危険の内容を図案化したものです。
(感電注意)
(例)
この記号は行為の禁止を表します。記号の中や近くの絵表示
行為の禁止
は、してはならない行為の内容を図案化したものです。
(分解禁止)
(例)
この記号は行為の強制を表します。記号の中の絵表示は、しな
ければならない行為の内容を図案化したものです。危険を避け
るためにはこの行為が必要です。
行為の強制
(コードを抜け)
注意の喚起
特定しない一般的な注意・警告を示しま
す。
高温による傷害を負うおそれがあること
を示します。
発煙または発火のおそれがあることを示
します。
感電のおそれがあることを示します。
行為の禁止
行為の強制
本製品を分解・修理・改造しないでくだ
さい。感電や火災のおそれがあります。
特定しない一般的な禁止を示します。
特定しない一般的な使用者の行為を指示
します。説明に従った操作をしてくださ
い。
本製品の電源コードをコンセントから
抜いてください。火災や感電のおそれが
あります。
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES ON SAFETY - Always read the Notes -
The following includes information necessary for proper and safe operation of the product.
SAFETY INDICATIONS
In the User’s Guide, "WARNING" or "CAUTION" is used to indicate a degree of danger. These terms are
defined as follows:
Indicates the presence of a hazard that may result in death or serious personal
injury.
WARNING
Indicates the presence of a hazard that may cause minor personal injury,
including burns, or property damage.
CAUTION
Precautions against hazards are presented with the following symbols. The individual symbols are defined as
follows:
(Example)
This symbol indicates the presence of a hazard.
Attention
An image in the symbol illustrates the hazard type.
Precaution against electric
shock
(Example)
Prohibited
Action
This symbol indicates prohibited actions. An image in
the symbol illustrates a particular prohibited action.
Prohibition of disassembly
(Example)
This symbol indicates mandatory actions. An image
in the symbol illustrates a mandatory action to avoid
a particular hazard.
Mandatory
Action
Unplug the power cord!
Symbols Used in This Manual
Attentions
Indicates a general notice or warning that cannot be specifically identified.
Indicates that improper use may cause an electric shock.
Indicates that improper use may cause personal injury due to high temperature.
Indicates that improper use may cause fumes or fire.
Prohibited Actions
Indicates a general prohibited action that cannot be specifically identified.
Do not disassemble, repair, or modify the product. Otherwise, an electric shock or fire may be
caused.
Mandatory Action
Indicates a mandatory action that cannot be specifically identified. Make sure to follow the
instruction.
Unplug the power cord of the server. Otherwise, an electric shock or fire may be caused.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
安全上のご注意
本製品を安全にお使いいただくために、ここで説明する注意事項をよく読んでご理解し、安全にご
活用ください、記号の説明については巻頭の「安全にかかわる表示」の説明をご参照ください。
警告
人命に関わる業務や高度な信頼性を必要とする業務には使用しない
本製品は、医療機器、原子力設備や機器、航空宇宙機器、輸送設備や機器など、人命に関わる設
備や機器および高度な信頼性を必要とする設備や機器などへの組み込みやこれら機器の制御な
どを目的とした使用は意図されておりません。これら設備や機器、制御システムなどに本製品を
使用した結果、人身事故、財産損傷などが生じても当社はいかなる責任も負いかねます。
ご自分で分解、修理、改造はしない
本書に記載されている場合を除き、絶対に分解したり、修理・改造を行ったりしないでください。
装置が正常に動作しなくなるばかりでなく、感電や火災の危険があります。故障の際はお買い求
めの販売店または保守サービス会社にご連絡ください。
煙や異臭・異音がしたまま使用しない
万一、煙・異臭・異音などが生じた場合は、ただちに電源をOFFにして電源コードをコンセント
から抜いてください。その後、お買い求めの販売店または保守サービス会社にご連絡ください。
そのまま使用すると火災の原因となります。
針金や金属片を差し込まない
本製品に金属片や針金などの異物を差し込まないでください。感電の危険があります。
光線を直視しない
NF9330-SF02SFPモジュールは、レーザー安全基準クラス1に適合していますが、、近距離(20cm
以内)での直視は瞳孔に悪影響を与える恐れがあります。動作中はSFPモジュールのポートをの
ぞきこまないでください。また、光ファイバーケーブルを接続していない場合は必ず付属の防塵
カバー(ゴムキャップ)をはめ、コネクタ端子を保護してください。
<次頁に続く>
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
注意
確実に接続する
本製品をブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロットに実装すると
きは、確実に差し込んでイジェクトレバーをストッパで固定してください。完全に差し込まなか
ったり、イジェクトレバーをストッパで固定しなかった場合、発煙や発火のおそれがあります。
指定以外のインターフェースケーブルを使用しない
インターフェースケーブルは、指定するものを使用し、接続する装置やコネクタを確認した上で
接続してください。指定以外のケーブルを使用したり、接続先を誤ったりすると、ショートによ
り感電や火災を起こすことがあります。
インターフェースケーブルの取り扱いや接続について次の注意をお守りください。
・破損したケーブルを使用しない。
・ケーブルを踏まない
・ケーブルの上にものを載せない
・ケーブルを改造・加工・修復しない
携帯電話などを近くで使用しない
携帯電話やPHS、ポケットベルなどを近くで使用しないでください。電波による誤動作の原因
となります。
腐食性ガスの存在する環境で使用または保管しない
腐食性ガス(二酸化硫黄、硫化水素、二酸化窒素、塩素、アンモニア、オゾンなど)の存在する
環境に設置し、使用しないでください。また、ほこりや空気中に腐食を促進する成分(塩化ナト
リウムや硫黄など)や導電性の金属などが含まれている環境へも設置しないでください。装置内
部のプリント板が腐食し、故障および発煙・発火の原因となるおそれがあります。もしご使用の
環境で上記の疑いがある場合は、販売店または保守サービス会社にご相談ください。
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Indications
This section provides notes on using your product safely. Read this section carefully to ensure
proper and safe use of the product. For symbols, see "SAFETY INDICATIONS" provided earlier.
WARNING
Do not use this product for services where critical high availability may directly affect
human lives.
This product is not intended for use or control in the facilities or devices concerning human
lives, including medical devices, nuclear facilities and devices, aeronautics and space
devices, transportation facilities and devices; and facilities and devices requiring high
reliability. NEC assumes no liability for any accident resulting in personal injury, death, or
property damage if this product has been used in the above conditions.
Do not disassemble, repair, or modify this product.
Never attempt to disassemble, repair, or modify this product on any occasion other than
described in this manual. Failure to follow this instruction may cause an electric shock or fire
as well as malfunctions of this product.
Do not use this product if any smoke, odor, or noise is present.
If smoke, odor, or noise is present, immediately turn off the POWER/SLEEP switch and
disconnect the power plug from the outlet, then contact your service representative. Using
this product in such conditions may cause a fire.
Do not insert foreign substances into this product.
Do not insert foreign substances including wires and metal pieces into this product. Failure to
follow this instruction may cause an electric shock.
Do not view laser directly.
The NF9330-SF02 SFP module confirms to laser safety standard class 1. However, do not
view the laser within a short distance of up to 20 cm. Failure to follow this instruction may
have bad influence on your pupils. Do not look in the port of each SFP module during
operation. If an SFP module is not connected with an optical fiber cable, always put the
attached dust-proof cover (rubber cap) on the connector terminal of the SFP module to
protect it.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Connect firmly.
Insert this product into a Blade Enclosure (SIGMABLADE) securely and fix the eject lever
with the stopper when installed. If this product is inserted incompletely or the eject lever is not
fixed with the stopper, smoke and/or fire may occur.
Do not use any unauthorized interface cable.
Use interface cables authorized by NEC only. Check the devices and connectors to which the
interface cables are connected. Using an unauthorized cable or connecting an interface cable
to an incorrect device or connector may cause an electric shock and/or fire to occur. Observe
the following notes on the uses and connections of interface cables.
Do not use any damaged cable.
Do not step on the cable.
Do not place any object on the cable.
Do not alter, modify, or repair the cable.
Do not use a cellular phone or pager around this product.
Turn off the cellular phone or pager. Radio interference may cause malfunctions of this
product.
Do not use or store this product in corrosive environment.
Avoid the usage or storage of this product in an environment which may be exposed to
corrosive gases, such as those including but not limited to: sulfur dioxide, hydrogen sulfide,
nitrogen dioxide, chlorine, ammonia and/or ozone. Avoid installing this product in a dusty
environment or one that may be exposed to corrosive materials such as sodium chloride
and/or sulfur. Failure to follow this instruction may corrode printed circuit boards in this
product, resulting in damage to this product and even smoke and/or fire. If there are any
concerns regarding the environment at the planned site of installation or storage, please
contact your service representative.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
使用上のご注意 ~本製品を正しく動作させるために~
本製品を使用するときに注意していただきたいことを次に示します。これらの注意を無視して、本
製品を使用した場合、資産(データやその他の装置)が破壊されるおそれがありますので必ずお守り
ください。
本製品は大変静電気に弱い電子部品です。ブレード収納ユニット(SIGMABLADE)の金属フレーム
部分などに触れて身体の静電気を逃がしてから取り扱ってください。また、本製品の端子部分
や部品を素手で触ったり、直接机の上に置いたりしないでください。
本製品を落としたり物にぶつけたりしないでください、誤動作や故障するおそれがあります。
本書及びブレード収納ユニット(SIGMABLADE)のユーザーズガイドに記載されている説明をよく
お読みになり、正しく取り扱ってください。
ブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロットにうまく本製品を取り付け
られないときは、いったん本製品を取り外してから取り付けなおしてください。過度の力を加
えると破損するおそれがありますので注意してください。
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Use - For Proper Operation -
Note the following when you use the product. If you ignore the notes, your assets (including important
data and/or other devices) may be damaged.
The product is extremely sensitive to static electricity. Make sure to touch the metal frame of the
Blade Enclosure (SIGMABLADE) to discharge static electricity from your body before handling the
product. Do not touch the terminals or component of the product by a bare hand and place the
product directly on the desk.
Do not drop the product. Do not make the product hit against other objects. Failure to follow these
instructions may cause the product to operate incorrectly or to be damaged.
Read carefully this Guide and the User's Guide of the Blade Enclosure (SIGMABLADE) to use the
product correctly.
If the product cannot be installed in switch module slot of the Blade Enclosure (SIGMABLADE)
securely, remove the product once and then install it again. Adding excess force to the product may
cause the product to be damaged.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
本書について
本書は、N8406-019/N8406-020 FCスイッチモジュールを正しくセットアップし、使用できるようにするため
の手引きです。本製品を使用される前に本書をよくお読みになり、いつでも取り出せる場所に大切に保管し
てください。本製品の移設の際は必ず本書も一緒に移設してください。
本書は、Windowsなどのオペレーティングシステムやキーボード、マウスといった一般的な入
出力装置などの基本的な取り扱いについて十分な知識を持ったユーザを対象として記載され
ています。
本文中の記号
本文中では次の3つの記号を使用しています。それぞれの意味を示します。(「安全にかかわる表示」
については6ページをご参照ください)
本製品を取り扱う上で守らなけれ
本製品を取り扱う上で確認してお
ばならない事柄や特に注意すべき
点を示します。
チェック
く必要がある点を示します。
重要
知っておくと役に立つ情報や、便
利なことなどを示します。
ヒント
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
This guide describes how to setup and use the N8406-019/020 FC switch module. Read thoroughly
this guide before using the product, and store it in a place that you are able to access it easily for
future reference. When transferring the product, always attach this guide to the product.
The guide is intended for persons who are familiar with operating systems including Windows and
fundamental operations of general-purpose I/O devices including the keyboard and mouse.
Text Conventions
The following conventions are used throughout this User's Guide. For safety symbols, see
"SAFETY INDICATIONS" provided earlier.
Items to be observed or points to
be noted when handling the
product
Information useful or convenient
for you
Items to be checked when
handling the product
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
梱包箱の中身について
梱包箱の中には本製品以外に色々な部品が入っています。「第2章 構成品」を参照し、全ての添付品がそろ
っていることを確認してください。万一、足りないものや破損しているものがあった場合には、本製品をご
購入された販売店にご連絡ください。
保証について
本製品には「保証書」が添付されています。「保証書」は販売店で所定事項を記入しお渡ししますので、記載
内容をご確認の上、大切に保管してください。保証期間中に故障した場合には、「保証書」の記載内容に基づ
き無償修理致します。保証後の修理については、ご購入された販売店もしくはご契約されている保守サービ
ス会社にご相談ください。
製品寿命について
本製品の製品寿命は5年です。本製品の交換については、本製品をご購入された販売店もしくはご契約され
ている保守サービス会社へご相談ください。
第三者への譲渡について
本製品を第三者に譲渡(または売却)する時には、必ず本書を含む全ての添付品をあわせて譲渡(または売
却)してください。
ソフトウェアに関しては、譲渡した側は一切の複製物を所有しないでください。また、インストールした装
置から削除した後、譲渡してください。
輸送について
本製品を輸送する際は、「第2章 構成品」を参考にブレード収納ユニット(SIGMABLADE)から本製品を取り外
し、本製品とすべての添付品を購入時の梱包箱に入れてください。
データの保管について
オペレータの操作ミス、衝撃や温度変化等による装置の故障によってデータが失われる可能性があります。
万一に備えて、ハードディスクドライブに保存されている大切なデータは、定期的にバックアップを行って
ください。
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
In the Package
The shipping carton contains various accessories, as well as the product itself. See "2. Components" to
make sure that you have everything and that individual components are not damaged. If you find any
component missing or damaged, contact your service representative.
Service Life
The service life of this product is five years. Ask your service representative for replacement of the product.
Transfer to Third Party
Make sure to provide this guide and all the accessories along with the product to a third party.
To transfer or sell any software application that comes with the product to a third party, the following
requirements must be satisfied:
All provided software applications must be transferred and no backup copies must be retained.
Software applications must be uninstalled before transferring the product.
Transportation
To transport the product, remove the product from the Blade Enclosure (SIGMABLADE) and put it in the
shipping carton along with accessories according to "2. Components" described later.
Data Backup
The device failure due to shock or thermal changes, as well as operator's misconduct, may cause loss of
data. To avoid loss of data, NEC recommends that you should make a back-up copy of your valuable data on
a regular basis.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
廃棄について
本製品の廃棄については、各自治体の廃棄ルールに従って分別廃棄してください。詳しくは、各自治体にお
問い合わせください。
分別廃棄のためにリチウム電池を取り外す場合は、保守サービス会社にお問い合わせ下さい。
リチウム電池
警告
リチウム電池を取り外さない
本製品内部にはリチウム電池が取り付けられています。電池を取り外さないでくださ
い。電池を火に近づけたり、水に浸したりすると爆発のおそれがあります。
分別廃棄のために電池を取り外す場合には、保守サービス会社に問い合わせて下さい。
フロッピーディスク、その他書き込み可能なメディア(CD-R/CD-RWなど)に保存
されているデータは、第三者によって復元や再生、再利用されないようお客様の責任にお
いて確実に処分してから廃棄してください。個人のプライバシーや企業の機密情報を保護
するために十分な配慮が必要です。
重要
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal
Dispose of the product according to all national laws and regulations. Contact your service representative on
removal of lithium batteries for segregation disposal.
Lithium battery
WARNING
Do not remove the lithium battery.
The switch module contains the lithium battery. Do not remove the battery. Placing the
lithium battery close to a fire or in the water may cause an explosion. Contact your service
representative on removal of lithium batteries for disposal.
It is the user's responsibility to completely erase or modify all the data stored in
storage device such as hard disk drive, backup data cartridge, floppy disk, or any
other media (CD-R/CD-RW) so that the data cannot be restored.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
目次
まえがき ................................................................. - 2 -
安全にかかわる表示................................................................ - 6 -
安全上のご注意 ................................................................... - 8 -
本文中の記号 .................................................................... - 14 -
梱包箱の中身について............................................................. - 16 -
保証について .................................................................... - 16 -
製品寿命について ................................................................ - 16 -
第三者への譲渡について........................................................... - 16 -
輸送について .................................................................... - 16 -
データの保管について............................................................. - 16 -
廃棄について .................................................................... - 18 -
目次 ............................................................................ - 20 -
1.本製品について......................................................... - 22 -
1-1.仕様 ........................................................................ - 22 -
1-2.本製品の特徴 ................................................................ - 22 -
2.構成品 ................................................................ - 23 -
3.各部の名称と機能 ...................................................... - 23 -
4.セットアップ手順 ...................................................... - 27 -
4-1.本製品の取り付け/取り外し.................................................... - 28 -
4-2.SFPモジュール取り付け/取り外し .............................................. - 33 -
4-3.FCスイッチモジュールの設定 .................................................. - 35 -
4-4.周辺機器接続 ................................................................ - 36 -
4-5.周辺機器接続確認............................................................. - 37 -
5.注意事項/困ったときの処理 ............................................. - 38 -
5-1.困ったときの処理............................................................. - 38 -
付録 シリアルポート接続 ................................................. - 58 -
付録 周辺機器接続確認 ................................................... - 59 -
付録 カスケード接続 ..................................................... - 62 -
付録 装置設定機能 ....................................................... - 69 -
PASSWORD設定変更................................................................ - 69 -
ネットワーク設定変更............................................................. - 70 -
スイッチネーム設定変更........................................................... - 72 -
ポートデータレート設定変更....................................................... - 73 -
ポートトポロジー設定変更......................................................... - 75 -
Domain ID設定変更............................................................... - 77 -
Principal Selection Mode確認/設定 .............................................. - 79 -
ゾーニング設定 .................................................................. - 81 -
時刻設定/タイムサーバー設定...................................................... - 97 -
各種設定の保存/再設定.......................................................... - 100 -
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface .......................................................................... - 3 -
NOTES ON SAFETY - Always read the Notes -.......................... - 7 -
Symbols Used in This Manual....................................................... - 7 -
Safety Indications .............................................................. - 10 -
Notes on Use - For Proper Operation -............................................ - 13 -
About This Guide ................................................................ - 15 -
Text Conventions ................................................................ - 15 -
In the Package .................................................................. - 17 -
Service Life .................................................................... - 17 -
Transfer to Third Party.......................................................... - 17 -
Transportation .................................................................. - 17 -
Data Backup ..................................................................... - 17 -
Disposal ........................................................................ - 19 -
Contents ........................................................................ - 21 -
1. Overview ............................................................. - 40 -
1-1. Specification .............................................................. - 40 -
1-2. Features ................................................................... - 40 -
2. Components ........................................................... - 41 -
3. Names and Features of Sections ....................................... - 41 -
4. Setup Procedure of FC Switch Module .................................. - 45 -
4-1. Installing/Removing the FC Switch Module.................................... - 46 -
4-2. Installing/Removing SFP Module.............................................. - 51 -
4-3. Setting FC Switch Module.................................................... - 53 -
4-4. Connecting Peripherals...................................................... - 54 -
4-5. Checking Connections of Peripherals......................................... - 55 -
5. Troubleshooting ...................................................... - 56 -
Appendix: Connecting Serial Port ....................................... - 103 -
Appendix: Checking Connections of Peripherals........................... - 104 -
Appendix: Cascade Connection ........................................... - 107 -
Appendix: FC Switch Module Setting Features ............................ - 114 -
Changing Password .............................................................. - 114 -
Changing Network Setting........................................................ - 115 -
Changing Switch Names........................................................... - 117 -
Changing Port Data Rate......................................................... - 118 -
Changing Port Topology.......................................................... - 120 -
Changing Domain ID ............................................................. - 122 -
Checking / Setting Principal Selection Mode..................................... - 124 -
Setting Zoning ................................................................. - 126 -
Setting Time and Time Server.................................................... - 141 -
Saving/Restoring Setting Values................................................. - 144 -
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1.本製品について
1-1.仕様
仕様
項目
備考
N8406-019
N8406-020
Fibre Channel機器の接続に
は SFP モジュールが必要に
なります。
外部×4
内部x8
外部x8
内部x16
Fibre Channelインターフェース
Fibre Channel速度
ポート数
2Gbps/4Gbps
-
12
24
-
SIGMABLADE-M/SIGMABLADE-H
のスイッチモジュールスロ
ットへ実装可能
形態
ブレード
208mm(幅)×29.3 mm(高さ)
280mm(奥行)
外形寸法
-
重量
1.3kg 以下
-
-
-
動作電圧
消費電力
12.0V
35W
温度 0 ~ 43℃
湿度 5 ~ 90%
温度 -40 ~ 70℃
湿度 5 ~ 95%
動作時
保管時
動作環境
結露しないこと
1-2.本製品の特徴
N8406-019/N8406-020 FC スイッチモジュールは、Express5800/BladeServer シリーズ専用の Fibre
Channel Switch Moduleです。本製品によってFibre Channel機器を接続することができます。
本製品は以下の機能を有します。
● Fabricによるデバイス接続
● ポートデータレート固定機能
● ポートTopology固定機能
● ポートゾーニング機能/WWNゾーニング機能
● SIGMABLADE-M/SIGMABLADE-Hに実装が可能
● カスケード接続機能
弊社が指定するブレード収納ユニット(SIGMABLADE)以外への実装及び Fibre
Channel 機器の接続はしないでください。指定以外のブレード収納ユニットへの実
装及び Fibre Channel 機器の接続ができたとしても本製品及び接続した Fibre
Channel機器が正常に動作しないばかりか、故障するおそれがあります。
実装可能な装置本体及び接続可能なFibre Channel機器については、本製品を購入
された販売店または保守サービス会社にお問い合わせください。
Fibre Channel機器を本製品の外部ポートに接続するには別途SFPモジュールが必
要になります。
重要
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.構成品
梱包箱にはFCスイッチモジュール以外に付属品が入っています。添付の構成品表を参照し全てそろっ
ていることを確認してください。万一、足りないものや破損しているものがありましたら、販売店に
ご連絡ください。
・ FCスイッチモジュール
・ ユーザーズガイド
3.各部の名称と機能
② ① ⑤ ⑥
17
18
19
20
21
22
23
0
ID
!
ACT
RST
外部ポート※
(SFPスロット)
ポート番号:21/22/23/0
装置シリアルNoラベル
内部ポート側コネクタ
外部ポート
(SFPスロット)
ポート番号:17/18/19/20
④ ③
①IDランプ
④RSTボタン
②Statusランプ
③ACTランプ
⑤ポートStatusランプ
⑥ポートSpeedランプ
イジェクタ
ストッパ
外部ポート
※ N8406-019では外部ポート
ポート番号:21/22/23/0は利用不可となります。
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) ランプ表示
本製品のランプの点灯条件は以下となります。
ランプの点灯状態をご確認いただき必要な処置を実施ねがいます。
① IDランプ
ランプの状態
状態
必要な対処
-
ブルー点灯 or消灯
正常状態
ID ランプが本製品の電源投入後 3 分以上してブルー点灯または消灯以外の状
態の場合は本製品に障害が発生している可能性があります。お買い求めの販売
店または保守会社にご連絡をおねがいします。
重要
② Statusランプ
ランプの状態
状態
必要な対処
-
グリーン点灯
正常状態
Status ランプが本製品の電源投入後 3 分以上して点灯しない場合は本製品に
障害が発生している可能性があります。お買い求めの販売店または保守会社に
ご連絡をおねがいします。
重要
③ ACTランプ
ランプの状態
状態
必要な対処
-
グリーン点灯
正常状態
スイッチモジュール起動が終了して スイッチモジュールの電源が入
消灯
いない、またはスイッチモジュール っているか、正常起動している
の起動障害が発生
温度異常等の装置異常が発生してい お買い求めの販売店または保守
る可能性があります 会社にご連絡願います。
1 つ以上のポートがオフライン状態 ポートStatusランプを確認して
となっている ください。
か確認してください
グリーンの低速点滅
(1秒間隔)
アンバー点灯
装置起動時に本ランプが一時的にアンバー点灯になります。
グリーン点灯以外の状態では本製品に障害が発生しています、必要な処置を実
施しても障害が解決しない場合はお買い求めの販売店または保守会社にご連
絡をおねがいします。
重要
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
④ ポート Statusランプ (ポート番号の左側のLED)
LEDの状態
詳細内容
SFPモジュールに対し信号がないかSFPモジュールにケーブルが接続さ
れていない、またはFibre Channel機器が接続されていない状態
オンライン(デバイスが接続済み)でトラフィックが流れていない
ポートがオンラインでかつポートにトラフィックが流れている状態
消灯
グリーン点灯
グリーンの点滅
(不定期な点滅)
ポートが光または信号を受信しているが、まだオンラインにはなってい
ない状態
アンバー点灯
アンバーの低速点滅 自己診断の結果本製品のポートに不具合がありポートが Disable 状態
(1秒間隔) となっている。 ※
アンバーの高速点滅 ポートがフォルト状態になっている ※
(0.25秒間隔)
アンバーとグリーン ポートがバイパスモードになっている ※
が交互に点滅
表中、詳細内容の項目に“※”印が記載されている状態では装置障害が発生し
ています。お買い求めの販売店または保守会社にご連絡をおねがいします。
重要
⑤ ポート Speedランプ (ポート番号の右側のLED)
LEDの状態
消灯
詳細内容
1Gbps モード
2Gbps モード
4Gbps モード
グリーン点灯
アンバー点灯
本製品においてはポートデータレート1Gbps製品の接続は未サポートです。
重要
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) 外部ポート
Fibre Channel 機器を接続可能なSFP ポート。
本製品上には 8 個の SFP ポートが実装されていますが利用可能なポート番号は製品毎に異なります。
利用可能なポートは下記表を参照願います。
利用の可否
ポートNo
N8406-019
N8406-020
ポート17
ポート18
ポート19
ポート20
ポート21
ポート22
ポート23
ポート0
○
○
○
○
×
×
×
×
○
○
○
○
○
○
○
○
利用不可のSFPスロットに関してもSFPモジュールは実装は可能ですが、Fibre
Channel 機器接続はできません。
重要
(3) 内部ポート
ブレード収納ユニット(SIGMABLADE)内で CPU ブレード内部のメザニン拡張スロットに搭載された
Fibre Channel コントローラと接続するポート。
本製品上には 16 個の内部ポートが実装されていますが利用可能なポート番号は製品毎に異なります。
利用可能なポートは下記表を参照願います。
利用の可否
接続される
CPU ブレード
スロット1
スロット2
スロット3
スロット4
スロット5
スロット6
スロット7
スロット8
スロット9
スロット10
スロット11
スロット12
スロット13
スロット14
スロット15
スロット16
ポートNo
N8406-019
N8406-020
ポート1
ポート2
ポート3
ポート4
ポート5
ポート6
ポート7
ポート8
ポート9
ポート10
ポート11
ポート12
ポート13
ポート14
ポート15
ポート16
○
○
○
○
○
○
○
○
×
×
×
×
×
×
×
×
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
各内部ポートが接続されるCPUブレードのスロット番号は固定です。変更はで
きません。詳細に関してはご利用になるブレード収納ユニット(SIGMABLADE)
のユーザーズガイドを参照してください。
重要
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4.セットアップ手順
次の手順に従って本製品のセットアップを行います。
「ユーザーズガイド(本書)」
の説明範囲
本製品の取り付け/取り外し
→28ページ
→33ページ
→35ページ
→36ページ
ブレード収納ユニット(SIGMABLADE)に本製品を取り付けます。
SFPモジュールの取り付け/取り外し
FCスイッチモジュールにSFPモジュールを取り付けます。
FCスイッチモジュールの設定
FCスイッチ内の各種設定を実施する。
周辺機器接続
FCスイッチ外部ポートへ周辺機器を接続する。
FC スイッチモジュール間のカスケード接続を実施する場合は、「周辺機器接
続」の前に「付録 カスケード接続」を実施してください。
重要
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1.本製品の取り付け/取り外し
取り付け手順
次に示す手順に従って本製品をブレード収納ユニット(SIGMABLADE)に取り付けます。
ブレード収納ユニット(SIGMABLADE)への本製品の実装時には以下の点に注意
願います。
重要
・本製品を一枚づつ実装し、先に実装した製品が起動した後、次の装置を実装
してください。本製品の同時実装を行った場合、内部ポートの Linkup 不具
合が発生する場合があります。
注意
確実に接続する
FC スイッチモジュールをブレード収納ユニット(SIGMABLADE)に取り付ける際は確実に取り付け
てください。中途半端に取り付けると接触不良を起こし、発煙や発火の原因となるおそれがあり
ます。
1. 本製品を取り付けるブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロット番号
を確認します。
各ブレード収納ユニット(SIGMABLADE)におけける本製品実装可能スイッチモジュールスロッ
ト番号
SIGMABLADE-M
SIGMABLADE-H
-H
スロット1
スロット2
スロット6
スロット3
スロット5
スロット7
スロット4
スロット6
スロット8
スロット5
スロット3
スロット4
スロット2
スロット1
FCスイッチモジュール搭載可能スロット
(スロット番号3~6)
実装可能なスイッチモジュールスロット番号に関する詳細情報に関してはご
利用になるブレード収納ユニット(SIGMABLADE)のユーザーズガイドを参照願
います。
重要
本製品の実装に関してはブレード収納ユニット(SIGMABLADE)起動状態での実
装が可能です。なお、実装実施時の注意事項に関してはブレード収納ユニット
(SIGMABLADE)のユーザーズガイドを参照願います。
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. ブレード収納ユニット(SIGMABLADE)のユーザーズガイドに従ってブレード収納ユニット
(SIGMABLADE)から本製品を取り付けるスイッチモジュールスロットのダミーモジュールまた
はブランクカバーを取りはずします。
ブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロット、ダミー
モジュールまたはブランクカバーの取り外し方法に関してはブレード収納
ユニット(SIGMABLADE)のユーザーズガイドを参照願います。
ヒント
3. 本製品のイジェクタのストッパをはずしイジェクタを開きます。
ストッパを右方向に軽く押す事によりストッパが外れイジェクタが開きま
す。
ヒント
4. ブレード収納ユニット(SIGMABLADE)のユーザーズガイドに従って本製品をブレード収納ユニ
ット(SIGMABLADE)に取り付けます。
本製品を軽く押し込みブレード収納ユニット(SIGMABLADE)のコネクタに本
製品のコネクタを軽く押し込みます。
ヒント
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. イジェクタをストッパがロックされるまで押し込み固定します。
本製品の取り付け・取り外し方法はブレード収納ユニット(SIGMABLADE)により
異なりますので必ずブレード収納ユニット(SIGMABLADE)のユーザーズガイドを
お読みください。
チェック
ブレード収納ユニット(SIGMABLADE)に本製品を取り付けられないときは、いっ
たん本製品を取り外してから取り付けなおしてください。過度の力を加えると
破損するおそれがありますので注意してください。
また、本製品の取り外し後、10秒以上間隔をあけ再取り付けしてください。
Fibre Channel コントローラの実装箇所に対応したブレード収納ユニット
(SIGMABLADE)のスイッチモジュールスロットに本製品を実装してください。そ
れぞれの実装箇所が対応していないと、周辺機器を接続することが出来ません。
詳細についてはブレード収納ユニット(SIGMABLADE)、CPU ブレードもしくは
Fibre Channelコントローラのユーザーズガイドをお読みください。
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
取り外し手順
次に示す手順に従って本製品をブレード収納ユニット(SIGMABLADE)より取り外します。
1. 本製品に接続しているFCケーブルを取り外します。
FCケーブルの取り外し作業実施時には細心の注意を払い作業を実施願います。
無理な力でFCケーブルの取り外しを行った場合、FCケーブルのコネクタ破損、
ケーブル断線が発生する場合があります。
重要
取り外した FC ケーブルのコネクタ部には必ずキャップの装着をお願いしま
す。キャップ未装着で FC ケーブルを放置した場合、再使用時に埃の付着等に
よる障害発生の原因となる場合があります。
2. 本製品に実装しているSFPモジュール取りはずします。
SFPモジュールの取り外し方法に関しては4-2項を参照願います。
ヒント
取り外したSFPモジュールには必ず防塵カバーの装着をお願いいたします。防
塵カバー未装着でSFPモジュールを放置した場合、再使用時に埃の付着等によ
る障害発生の原因となる場合があります。
重要
3. 取り外す製品のストッパをはずしイジェクタを開きます。
ストッパを右横方向に軽く押す事によりストッパが外れイジェクタが開き
ます。
ヒント
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. イジェクタを手前に軽く引いてください。
イジェクタを手前に引くことにより装置が手前に引き出され、ブレード収納
ヒント
ユニット(SIGMABLADE)コネクタから本製品のコネクタを抜くことができま
す。
5. ブレード収納ユニット(SIGMABLADE)より本製品を取り出してください。
6. 本製品を取り外したブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロットにダ
ミーモジュールまたはブランクカバーを取りつけてください。
ブレード収納ユニット(SIGMABLADE)のダミーモジュールまたはブランクカ
ヒント
バーの取り付け方法はブレード収納ユニット(SIGMABLADE)のユーザーズガ
イドを参照願います。
注意
高温に注意する
FC スイッチモジュール異常により取り外しを実施する場合は、装置本体が高温になっているた
め4項の作業を実施したあと、本製品が十分に冷めたことを確認してから装置の取り出しを行っ
てください。
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2.SFPモジュール取り付け/取り外し
本製品を実装後、Fibre Channel 周辺機器を接続するために外部ポートに SFP モジュールを実装し
ます。なお、ご利用可能なSFPモジュールは「NF9330-SF02」のみとなります。
N8406-019において利用可能な外部ポートは ポート17/ポート18/ポート19/
ポート20の4ポートとなります。ポート21/ポート22/ポート23/ポート0は
ご利用になれません。
重要
N8406-020において利用可能な外部ポートは ポート17/ポート18/ポート19/
ポート20/ポート21/ポート22/ポート23/ポート0の8ポートとなります。
SFPモージュールを本製品に取り付けた状態で保管又は運送する場合、ホコリ
等からFCコネクタ接続部を保護するため、必ずSFPモジュールに添付されて
いる「防塵カバー」を取り付けてください。
注意
光線を直視しない
NF9330-SF02SFPモジュールは、レーザー安全基準クラス1に適合していますが、、近距離(20cm
以内)での直視は瞳孔に悪影響を与える恐れがあります。動作中はSFPモジュールのポートをの
ぞきこまないでください。また、光ファイバーケーブルを接続していない場合は必ず付属の防塵
カバー(ゴムキャップ)をはめ、コネクタ端子を保護してください。
取り付け手順
SFPモジュールの本製品への実装時はSFPスロットの奥まで差し込んでください。
N8406-***
FCスイッチモジュール
NF9330-SF02
SFPモジュール
SFPポート
指定製品以外のSFPモジュールはご利用になれません。
重要
- 33 -
Download from Www.Somanuals.com. All Manuals Search And Download.
取り外し手順
SFPモジュールのレバー(引き抜き金具)を下ろしてください。
N8406-***
FCスイッチモジュール
NF9330-SF02
SFPモジュール
レバーをつまんで図中の矢印方向に引き抜いてください。
N8406-***
FCスイッチモジュール
SFPモジュール取外し時は必ずレバーを下ろし作業を実施してください。レバ
ーを下げずに SFP モジュールを引き抜いた場合、SFP モジュールの破損、SFP
スロットの破損等が発生する場合があります。
重要
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3.FCスイッチモジュールの設定
本製品をご利用になる場合、以下の設定を実施する必要があります。
PASSWORD 設定
ネットワーク設定(必須)
ポートデータレート設定(必須)
ポートトポロジー設定(必須)
Domain ID設定
Principal Selection Mode確認/設定
ゾーニング設定(必須)
時刻設定/タイムサーバー設定
※ それぞれの機能の利用方法に関しては「付録 装置設定機能」を参照願います。
注意
設定における注意
FC スイッチモジュールで設定していただく各項目は設定ミスをした場合システム障害を引き起
こす項目があります。実施する作業内容に関してはその機能及び影響を十分ご理解いただき実施
をお願いいたします。
- 35 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4.周辺機器接続
以下の手順に従って、本製品とFibre Channel周辺機器を Fibre Channelケーブルで接続します。
1. Fibre Channel機器を取り付けるFCスイッチモジュール及びポート番号を確認します。
2. SFPの光コネクタ接続部及び接続するFibre Channel ケーブルのコネクタ部を圧縮エアースプ
レーや専用クリーナーで清掃します。
3. FibreChannelケーブルの一方の端を本製品の SFPモジュールにしっかりと挿入し、接続しま
す。
4. Fibre Channel機器コネクタ接続部及び接続するFibre Channelケーブルのコネクタ部を圧縮
エアースプレーや専用クリーナーで清掃します。
5. Fibre Channel ケーブルのもう一方の端をFibre Channel 機器に接続します。
ご使用できる光ケーブルの型番とケーブル長は以下になります。
NF9320-SJ01 (5m) , NF9320-SJ11 (5m 被覆強化品)
NF9320-SJ02 (10m) , NF9320-SJ12 (10m 被覆強化品)
NF9320-SJ03 (20m) , NF9320-SJ13 (20m 被覆強化品)
NF9320-SJ04 (50m) , NF9320-SJ14 (50m 被覆強化品)
光ケーブルにつきましては以下のような専門知識が必要ですので、取り付けにつきましては以下の点
に関しご注意願います。
・
コンタクト部分にほこり/指紋等が付くと光出力/光感度が低下し、使用不能となる場合があります。
そのためFibre Channelケーブル接続時は接続前に圧縮エアースプレーや専用クリーナーでの清掃を
行い付着物の除去を行う必要があります。
・
・
Fibre Channelケーブルは曲げ半径50mm以上としてケーブルフォーミングしてください。
Fibre Channelケーブルにラベルを貼る際はコネクタ根元付近には張らないでください。光コネクタ
先端部分が開き接続不良の原因になります。
・
Fibre Channelケーブルの芯線は石英ガラスで出来ているため、コネクタの先は機械的ショック/固い
ものとの衝突に非常に弱く傷がつきやすく破損するおそれがあります。
指定以外のインタフェースケーブルを使用しない。
インタフェースケーブルはNECが指定するものを使用してください。指定以
外のケーブルを使用すると、ショートによる火災のおそれがあります。また、
インタフェースケーブルの取り扱いについては次の注意をお守りください。
・破損したケーブル及びコネクタを使用しない。
重要
・ケーブルを踏まない。
・ケーブルの上に物を載せない。
・ケーブルの接続がゆるんだまま使用しない。
・コネクタ-部付近に急激な引張力、曲げ、捻り等を加えない。
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5.周辺機器接続確認
以下の手順に従って、本製品上でFibre Channel機器が正常に認識していることを確認してください。
1. コンソール上で“switchshow”を入力してください。
→ Fibre Channel機器が正常にLinkupしていることを確認してください。
接続実施済みのFibreChannel機器が“switchshow”コマンドの表示結果中に
表示されない場合以下の確認を実施してください。
重要
・接続しているFibre Channel機器が正常に動作していますか。
・接続しているFCケーブルはきちんと接続されていますか。
2. コンソール上で“nsshow”を入力してください。
→ Fibre Channel機器のName Serverへの情報登録が正常に実施されていることを確認し
てください。
接続実施済みのFibreChannel機器の情報が“nsshow”コマンドの表示結果に
表示されていない場合以下の確認を実施してください。
・接続しているFibre Channel機器が正常に動作していますか。
・接続しているFCケーブルはきちんと接続されていますか。
“switchshow”の結果にFibreChannel機器の登録がされているポートにおい
て、“nsshow”の同一ポートの情報表示結果に Fibrefi Channel 機器の情報が
表示されない場合接続機器の接続に問題が発生している可能性があります。ご
使用になっているFibreChannel機器のユーザーズガイドを参照し処置の実施
してください。
重要
※ それぞれの確認方法に関しては「付録 周辺機器接続確認」を参照願います。
- 37 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5.注意事項/困ったときの処理
本製品をご使用される際の注意事項及び困ったときの処理について、下記に記します。
該当する項目がある場合は、説明に従って正しく対処してください。
5-1.困ったときの処理
本製品が正常に起動しない
本ユーザーズガイドの「3項 各部の名称称と機能」 (1)ランプ表示を参照し装置の状態を確認してく
ださい。
本製品が取り付けられているスロットに原因があると思われるときは、次の点について確認および対処
をしてください。
● 本製品のLEDが点灯していない場合
→ ブレード収納ユニット(SIGMABLADE)に添付のマニュアルを参照して、ブレード収納ユニット
(SIGMABLADE)の電源が投入されているかを確認してください。
● 本製品を取り付けたスイッチモジュールスロットで異常が発生している場合
→ もう一度しっかりと本製品を実装し直してください。
ブレード収納ユニット(SIGMABLADE)への本製品の実装確認を行う場合、本製品取り外し後の再
取り付けは10秒以上間隔をあけ実施してください。
以上の確認を行ってもブレード収納ユニット(SIGMABLADE)起動中にエラーメッセ
ージが表示される場合は、いったん本製品を別のスイッチモジュールスロットに取
り付け、ブレード収納ユニット(SIGMABLADE)を起動して本製品の起動に問題がない
ことを確認してください。装置起動が正常に行われた場合、ブレード収納ユニット
(SIGMABLADE)が故障していることが考えられます。ブレード収納ユニット
(SIGMABLADE)を購入された販売店または保守サービス会社にご連絡ねがいます。
重要
本製品が正常に動作しないとき
本製品をブレード収納ユニット(SIGMABLADE)に取り付けた後、本製品が正常に認識しなかったときは、
次の点について確認および対処してください。また、ブレード収納ユニット(SIGMABLADE)に添付のユー
ザーズガイドもあわせて参照してください。
● 本製品を実装したスイッチモジュールスロットの番号、CPU ブレードを実装したスロットの番号が
正しく対応が取れていますか?
→ CPUブレード、ブレード収納ユニット(SIGMABLADE)のユーザーズガイドを参照してください。
● 本製品のLEDは点灯していますか?
→ 本ユーザーズガイド「3項 各部の名称と機能」、(1) ランプ表示を参照してください。
● ブレード収納ユニット(SIGMABLADE)は正常に起動していますか?
→ ブレード収納ユニット(SIGMABLADE)のユーザーズガイドを参照してください。
● ブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロット位置を変え本製品の動作を確
認して下さい。
→ 実装可能なブレード収納ユニット(SIGMABLADE)のスイッチモジュールスロット番号はブレー
ド収納ユニット(SIGMABLADE)のユーザーズガイドを参照してください。
以上の確認を行っても本製品が正常に動作しない場合、本製品が故障していること
が考えられます。本製品を購入された販売店または保守サービス会社にご連絡ねが
います。
重要
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Fibre Channel 機器が認識できなくなったとき
本製品に接続してご使用になっていたFibreChannel機器が、ブレード収納ユニット(SIGMABLADE)の起
動後、OS から正常に認識されなくなった、またはアクセスできなくなった場合は、次の点について確
認および対処してください。また、ブレード収納ユニット(SIGMABLADE)及びFibreChannel機器に添付
のマニュアルやご使用になっているアプリケーションのマニュアルもあわせて参照してください。
● 接続されたFibre Channel機器のポートデータレートと本製品のポートデータレートは正しく設定
されていますか?
→ 接続したFibre Channel機器のに添付のマニュアルを参照してください。
● 接続されたFibre Channel機器のポートトポロジーと本製品のポートトポロジー設定は合っていま
すか?
→ 接続したFibre Channel機器のに添付のマニュアルを参照してください。
● SFPモジュール、FCケーブルはしっかり接続されていますか?
→ もう一度しっかりと接続し直してください。
● 本製品上で正しく接続機器を認識していますか?
→ 本ユーザーズガイドの「付録 周辺機器接続確認」を参照してください。
● 接続するFibre Channel機器は正常に動作・起動していますか?
→ 各機器に添付されたユーザーズガイドを参照の上、正常に動作・起動している事を確認してく
ださい。
● ゾーニング設定は正しく行われていますか?
→ ゾーニング設定を参照し正しいゾーニング設定が行われていることを確認してください。
● CPUブレード上でFibre Channelコントローラは正しく動作していますか?
→ CPUブレード及びFibre Channelコントローラのユーザーズガイドを参照し確認してください。
以上の確認を行ってもFibre Channel機器が認識できない場合は、本製品を購入さ
れた販売店または保守サービス会社にご連絡ねがいます。
重要
- 39 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Overview
1-1. Specification
Item
Rating
Remarks
N8406-019
N8406-020
SFP modules are required to
connect with fibre channel
devices.
External ports: 4
Internal ports: 8
External ports: 8
Internal ports: 16
Fibre channel interfaces
Fibre Channel speed
Number of ports
2G bps/4G bps:
–
–
12
24
Installable on a switch module
slot of SIGMABLADE-M or
SIGMABLADE-H
Type
Blade
External dimension
Weight
208 (width) × 29.3 (height) × 280 (depth) mm
1.3 kg max.
–
–
Operating voltage
Power consumption
12.0 VDC
35 W
–
–
Temperature: 0 to 43ºC
Humidity: 5 to 90%
Temperature: -40 to 70ºC
Humidity: 5 to 95%
Without condensation
Operating
Temperature
and humidity
Storage
1-2. Features
FC Switch Modules N8406-019/N8406-020 are designed to be used for NEC
Express5800/BladeServer series machines exclusively. The FC Switch Modules can connect with
fibre channel devices.
The FC Switch Modules have the following features:
Connecting with devices by fabric
Port data rate fixing
Port topology fixing
Port zoning/WWN zoning
Installable in SIGMABLADE-M/SIGMABLADE-H
Cascade connection
Do not install the FC Switch Modules in any Blade Enclosure
(SIGMABLADE) unauthorized by NEC. Do not connect the FC Switch
Modules with any fibre channel devices unauthorized by NEC. If an FC
Switch Module can be installed in an unauthorized Blade Enclosure
(SIGMABLADE) and connect with unauthorized fibre channel devices, the
FC Switch Module and/or the fibre channel devices may not operate
normally or further may be defected.
For Blade Enclosures (SIGMABLADE) in which the FC Switch Modules can
be installed and fibre channel devices which can be connected to the FC
Switch Modules, contact your service representative.
To connect fibre channel devices to external ports of the FC Switch Module,
SFP modules are required additionally.
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Components
The shipping carton contains the following items. Make sure that both components are packaged. If
either or both components are missed or damaged, contact your service representative.
FC Switch Module
User’s Guide
3. Names and Features of Sections
② ① ⑤ ⑥
17
18
19
20
21
22
23
0
ID
!
ACT
RST
Serial device number label
External ports (SFP slots)
Port numbers: 17, 18, 19,
and 20
External ports (SFP slots)*
Port numbers: 21, 22, 23,
and 0
④ ③
① ID LED
② Status LED
③ ACT LED
④ RST button
⑤ Port status LED
⑥ Port speed LED
Internal port connector
Ejector
Stopper
External
ports
* For N8406-019, external ports 21, 22, 23 and 0 are
unavailable.
- 41 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) ON/OFF Conditions of LEDs
The following describes the ON/OFF conditions of LEDs on the FC Switch Module.
Check the ON/OFF status of each LED to take required action.
1. ID LED
LED status
Condition
Required action
Illuminating in blue or OFF
Normal
–
If the ID LED does not illuminate in blue or is not OFF after passage for
three minutes or longer from power-on, a fault may occur in the FC Switch
Module. Contact your service representative.
2. Status LED
LED status
Condition
Required action
Illuminating in green
Normal
–
If the status LED does not illuminate after passage for three minutes or
longer from power-on, a fault may occur in the FC Switch Module. Contact
your service representative.
3. ACT LED
LED status
Condition
Required action
Illuminating in green
OFF
Normal
–
Starting the FC Switch Module is
not completed yet or an error
occurs in start of the FC Switch
Module.
Check if the power of the FC
Switch Module is set to ON and
the FC Switch Module is started
normally if set to ON.
Blinking in green
slowly (1-sec interval) temperature error may occur.
A device error such as a
Contact your service
representative.
One or more port are in the offline
Check the port status LED.
Illuminating in umber
status.
The ACT LED illuminates in umber temporarily while the FC Switch Module
is started.
If the ACT LED is in any status other than illuminating in green, an error
occurs in the FC Switch Module. If the error cannot be rejected in spite of
required action, contact your service representative.
- 42 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Port status LED (located to the left of each port number)
LED status
OFF
Description
No signals are sent to the SFP module, a proper cable is not
connected to the SFP module or a fibre channel device is not
connected to the SFP module.
Illuminating in green
Blinking in green
(irregular blinking)
No traffics flow in the online status (with a device connected).
The port is in the online status and traffics flow through the port.
The port receives optical signals but does not enter into the
online status yet.
Illuminating in umber
Blinking in umber slowly
(1-sec interval)
As a result of self-diagnosis, a malfunction is found in the port
and the port is in the disable status. *
Blinking in umber fast
(0.25-sec interval)
The port is in the fault status. *
Blinking in umber and green The port is in the bypass mode. *
alternately
A device error occurs in each status with asterisk mark (*) in the table
above. Contact your service representative.
5. Port speed LED (located to the right of each port number)
LED status
OFF
Illuminating in green
Illuminating in umber
Description
1G bps mode
2G bps mode
4G bps mode
The FC Switch Module does not support the connection of a device with port
data rate 1Gbps yet.
- 43 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) External Ports
The SFP ports enable the FC Switch Module to connect with fibre channel devices.
The FC Switch Module is equipped with eight SFP ports. However, available ports vary depending
on the type. See the table below for the available ports.
Available/unavailable
Port
N8406-019
N8406-020
Port 17
Port 18
Port 19
Port 20
Port 21
Port 22
Port 23
Port 0
√
√
√
√
–
–
–
–
√
√
√
√
√
√
√
√
An SFP module can be installed on an unavailable SFP slot. However, the
SFP module cannot connect the FC Switch Module with a fibre channel
device.
(3) Internal Ports
The internal ports allow the FC Switch Module to connect to fibre channel controllers inserted to
Mezzanine slots on the CPU blades in a Blade Enclosure (SIGMABLADE).
The FC Switch Module is equipped with 16 internal ports. However, available ports vary depending
on the type. See the table below for the available ports.
Available/unavailable
Port
Connected CPU blade
N8406-019
N8406-020
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
Port 8
Port 9
Port 10
Port 11
Port 12
Port 13
Port 14
Port 15
Port 16
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 7
Slot 8
Slot 9
Slot 10
Slot 11
Slot 12
Slot 13
Slot 14
Slot 15
Slot 16
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
The slot number of the CPU blade to which a specific internal port is
connected is fixed. Changing the number is not allowed. For details, refer to
the User’s Guide of the Blade Enclosure (SIGMABLADE) you use.
- 44 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Setup Procedure of FC Switch Module
The setup procedure of the FC Switch Module is described below.
Explained in this
User's Guide
Installing FC Switch Module
See Page 46.
See Page 51.
See Page 53.
See Page 54.
Install FC switch module in Blade Enclosure.
Installing SFP Module
Install SFP modules in FC switch module.
Setting Up FC Switch Module
Provide several settings for the FC Switch Modules.
Connecting Peripherals
Connect peripherals to the external ports on the FC Switch
Modules.
If FC Switch Modules are subjected to cascade connection, perform the
procedure described in "Appendix Cascade Connection" before connecting
peripherals to the FC Switch Modules.
- 45 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1. Installing/Removing the FC Switch Module
Installation Procedure
Install the FC Switch Module in a Blade Enclosure (SIGMABLADE) according to the procedure
described below.
Note the following when the FC Switch Modules is installed in a Blade
Enclosure (SIGMABLADE). If more than one FC Switch Module are installed
in a Blade Enclosure (SIGMABLADE), install them one by one. After the
previous FC Switch Module is started, install the next one. Installing more
than one FC Switch Module in a Blade Enclosure (SIGMABLADE)
simultaneously may cause linkup errors to occur at the respective internal
ports.
CAUTION
Install FC Switch Modules in a Blade Enclosure (SIGMABLADE) securely.
Install FC Switch Modules in a Blade Enclosure (SIGMABLADE) securely. Loose
installation may cause poor contact to lead smoke and/or fire.
1. Check the switch module slot on the Blade Enclosure (SIGMABLADE) into which the FC Switch
Module is inserted.
The figure below shows the switch module slots into which the FC Switch Modules can be installed
on each type of Blade Enclosures (SIGMABLADE).
SIGMABLADE-H
SIGMABLADE-M
Slot 1
Slot 3
Slot 5
Slot 7
Slot 2
Slot 4
Slot 6
Slot 8
Slot 5
Slot 3
Slot 1
Slot 6
Slot 4
Slot 2
Slots in which FC Switch Modules can be installed
(slot numbers 3 - 6)
For details of switch module slots into which FC Switch Modules can be
inserted, refer to the User’s Guide attached to the Blade Enclosure
(SIGMABLADE) to be used.
FC Switch Modules can be installed in a Blade Enclosure (SIGMABLADE) if
the Enclosure is operated. For the notes on the installation, refer to the
User’s Guide attached to the Blade Enclosure (SIGMABLADE).
- 46 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. According to the User’s Guide of the Blade Enclosure (SIGMABLADE), remove the dummy module
or blank cover on the switch module slot into which the FC Switch Module will be inserted.
For the procedure of removing a dummy module or blank cover from the
switch module slot of the Blade Enclosure (SIGMABLADE), refer to the
User’s Guide attached to Blade Enclosure (SIGMABLADE).
3. Unlock the stopper of the ejector on the FC Switch Module to unlatch the ejector.
Press the stopper lightly in the right direction to unlock the stopper. Then the
ejector is unlatched.
4. According to the User’s Guide of the Blade Enclosure (SIGMABLADE), install the FC Switch
Module in the Blade Enclosure (SIGMABLADE).
Push the FC Switch Module lightly to insert its connector into a mating
connector on the Blade Enclosure (SIGMABLADE).
- 47 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Push the ejector to lock the stopper. The FC Switch Module is fixed.
The installation/removal procedures of the FC Switch Module in/from a
Blade Enclosure (SIGMABLADE) vary depending on the Blade Enclosure
(SIGMABLADE) you use. For the procedure, always refer to the relevant
Blade Enclosure (SIGMABLADE).
If a FC Switch Module cannot be installed in a Blade Enclosure
(SIGMABLADE) properly, remove the FC Switch Module once and reinstall
it again. Applying excess force to the FC Switch Module may cause it to be
damaged. After the FC Switch Module is removed, wait for more than 10
seconds and then reinstall it.
Insert FC Switch Modules into switch module slots on a Blade Enclosure
(SIGMABLADE) corresponding to the locations on which fibre channel
controllers are installed. Without the correspondences, peripherals cannot
be connected to the FC Switch Modules. Refer to the User’s Guides of the
Blade Enclosure (SIGMABLADE), CPU blade and/or the fibre channel
controller for details.
- 48 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal Procedure
Remove the FC Switch Module from a Blade Enclosure (SIGMABLADE) according to the procedure
described below.
1. Remove the FC cable connected to the FC Switch Module.
Remove the FC cable with close attention. Removing the FC cable with
excess force may cause the mating connector on the FC cable to be
damaged or the cable to be disconnected.
Always put caps on the connectors of the removed FC cable. If a FC cable
is left without caps put on the connectors, a fault may occur in its reuse due
to dust adhering on the connectors.
2. Remove the SFP module installed on the FC Switch Module.
See Section 4-2 for the SFP module removal procedure.
Always put dust-proof cover on the removed SFP module. If an SFP module
is left without dust-proof cover, a fault may occur on its reuse due to dust
adhering on the module.
3. Unlock the stopper on the FC Switch Module to unlatch the ejector.
Press the stopper lightly in the right direction to unlock the stopper. Then the
ejector is unlatched.
- 49 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Pull out the ejector toward you lightly.
Pulling the ejector toward you allows the FC Switch Module to be pulled out
and thus the connector of the FC Switch Module to be removed from the
mating connector of the Blade Enclosure (SIGMABLADE).
5. Take out the FC Switch Module from the Blade Enclosure (SIGMABLADE).
6. Install a dummy module or blank cover in the switch module slot from which the FC Switch Module
was just removed.
For installing a dummy module or blank cover in a Blade Enclosure
(SIGMABLADE), refer to the User’s Guide of the Blade Enclosure
(SIGMABLADE).
CAUTION
Avoid installation in extreme temperature conditions.
If you need to remove the FC Switch Module due to occurrence of an error, wait
until the FC Switch Module is fully cooled down after performing job in step 4.
It is because the module is heated at a high temperature.
- 50 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2. Installing/Removing SFP Module
After the FC Switch Module is installed in the Blade Enclosure (SIGMABLADE), install SFP
modules on external ports to connect with fibre channel peripherals. SFP module NF9330-SF02 is
only available.
For N8406-019, four external ports, or ports 17, 18, 19 and 20 are available.
Ports 21, 22, 23, and 0 are unavailable.
For N8406-020, eight external ports, or ports 17, 18, 19, 20, 21, 22, 23 and
0, are available.
If an FC Switch Module with SFP modules installed are stored or carried,
always put the dust-proof covers attached to the SFP modules on them to
protect the FC connectors from dust.
CAUTION
Do not view laser directly.
The NF9330-SF02 SFP module confirms to laser safety standard class 1.
However, do not view the laser within a short distance of up to 20 cm. Failure to
follow this instruction may have bad influence on your pupils. Do not look in the
port of each SFP module during operation. If an SFP module is not connected
with an optical fiber cable, always put the attached dust-proof cover (rubber cap)
on the connector terminal of the SFP module to protect it.
Installation Procedure
To install an SFP module on the FC Switch Module, insert it to an SFP port to the depth.
N8406-*** FC Switch Module
NF9330-SF02 SFP module
SFP port
Insertion
direction
SFP modules authorized by NEC are only available.
- 51 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal Procedure
Pull down the lever on the SFP module.
N8406-*** FC Switch Module
NF9330-SF02 SFP module
Pull down
the lever
Hold the lever and pull out the module in the arrow direction shown in the figure.
N8406-*** FC Switch Module
Pull-out
direction
Before the SFP module can be removed, the lever should always be
lowered. If the SFP module is pulled out without the lever lowered, the SFP
module and/or slot may be damaged.
- 52 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3. Setting FC Switch Module
To use the FC Switch Module, the following information must be set.
Password,
Network (required),
Port data rate (required),
Port topology (required),
Domain ID,
Checking / Setting Principal Selection Mode
Zoning (required), and
Time and time server
See "Appendix Device Setting Features" for how to use the features.
CAUTION
Notes on settings
If one or more setting items required for the FC Switch Module are set
incorrectly, a system fault may occur. Before executing a job, you should be
familiar with its feature and influence sufficiently.
- 53 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4. Connecting Peripherals
Connect a fibre channel peripheral to the FC Switch Module through a fibre channel cable according to
procedure below:
1. Check the number of the port on the FC Switch Module on which the fibre channel device will be
installed.
2. Clean the optical connector on the SFP module and the mating connector of the fibre channel cable
used for connection with compressed air spray or exclusive cleaner.
3. Insert the connector to the SFP module on the FC Switch Module securely to connect it.
4. Clean the connector on the fibre channel device and the other connector of the fibre channel cable
with compressed air spray or exclusive cleaner.
5. Connect the connector of the cable to the fibre channel device.
The part numbers of available optical cables and their lengths are as follows:
NF9320-SJ01 (5 m), NF9320-SJ11 (5 m, reinforced shield type),
NF9320-SJ02 (10 m), NF9320-SJ12 (10 m, reinforced shield type),
NF9320-SJ03 (20 m), NF9320-SJ13 (20 m, reinforced shield type),
NF9320-SJ04 (50 m), and NF9320-SJ14 (50 m, reinforced shield type)
The following expert knowledge is required for optical cables. Note the following on connections of
optical cables:
If dust and/or fingerprints adhere to contacts on a fibre channel cable, then the optical power and/or
sensitivity of the cable may decrease to make the cable unavailable. Accordingly, before a fibre
channel cable can be connected to an SFP module or fibre channel device, it should be cleaned by
compressed air spray or exclusive cleaner to remove adhesions on the contacts.
Route a fibre channel cable with bending radius of 50 mm or larger.
Do not put labels near the ends of a fibre channel cable if required. The tips of the optical
connectors are opened to cause poor connections.
The cores of fibre channel cables are made of quartz glass. Thus, the tips of a connector are highly
sensitive to be damaged easily by mechanical shock or collision with a hard object.
Do not use any interface cables not authorized by NEC. Always use
interface cables authorized by NEC. Using interface cables other than those
authorized by NEC may cause fire to occur due to short circuit. Note the
following on handing interface cables:
– Do not use damaged cables and connectors.
– Do not step on cables.
– Do not put objects on cables.
– Do not use cables with loose connections.
– Do not apply sudden strain, bending, twisting to portions near the
connectors of cables.
- 54 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5. Checking Connections of Peripherals
Confirm that the FC Switch Module normally recognizes fibre channel devices according to the
following procedure:
1. Type "switchshow" on the console.
→ Confirm that the fibre channel devices are normally linked up.
If a fibre channel device already connected to the FC Switch Module does
not appear in the result of the "switchshow" command, check the following:
– Whether the connected fibre channel device operates normally, and
– Whether the FC cable is connected securely.
2. Type "nsshow" on the console.
→ Confirm that the information on the fibre channel devices is normally registered to the
relevant name server.
Check the following if the information on a fibre channel device already
connected does not appear in the result of the "nsshow" commend:
– Whether the connected fibre channel device operates normally and
– Whether the FC cable is connected securely.
A fibre channel device is registered for a port as a result of "switchshow" but
the information on the fibre channel device may not appear as a result of the
information on the same port by "nsshow". If so, some device connection
error may occur. Take proper action according to the User’s Guide of the
fibre channel device you use.
See "Appendix Checking Connections of Peripherals" for how to check the
connection of each peripheral.
- 55 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Troubleshooting
Read this section when any symptom of trouble occurs.
If the section explains the symptom, take an appropriate action as explained.
FC Switch Module fails to start
Check the status of the switch module according to "(1) ON/OFF conditions of LEDs" in Section 3
"Names and Features of Sections" described earlier in this guide.
If the slot containing the FC switch module is suspected, check the following and take an
appropriate action.
When LEDs on the switch module are unlit:
→ Check if the Blade Enclosure (SIGMABLADE) is powered on according to the User's Guide
of the Blade Enclosure (SIGMABLADE).
When the slot containing the FC switch module is faulty:
→ Securely insert the FC switch module again.
If the error message still appears while starting the Blade Enclosure
(SIGMABLADE), relocate the switch module to another slot. Power on the
Blade Enclosure (SIGMABLADE) and make sure that the switch module can
start normally. If the switch module starts normally, the Blade Enclosure
(SIGMABLADE) may be faulty. Consult with your service representative.
FC Switch Module does not operate properly
If the FC switch module is not detected after installed in the Blade Enclosure (SIGMABLADE), check
the following and take an appropriate action. See also the User's Guide of Blade Enclosure
(SIGMABLADE).
Check if the slot number of the switch module corresponds to that of the CPU blade.
→ Refer to the User’s Guides of the CPU blade and Blade Enclosure (SIGMABLADE).
Check if LEDs on FC switch module are lit.
→ See "(1) ON/OFF conditions of LEDs" in Section 3 "Names and Features of Sections"
described earlier in this guide.
Check if the Blade Enclosure (SIGMABLADE) starts normally.
→ Refer to the User’s Guide of the Blade Enclosure (SIGMABLADE).
Check if the FC switch module operates normally by relocating the installation slot.
→ Refer to the User's Guide of Blade Enclosure (SIGMABLADE) for the slot number available
for the FC switch module.
If the FC switch module is still unable to operate normally, the FC switch
module may be faulty. Consult with your service representative.
- 56 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Fibre channel device cannot be recognized
If a fibre channel device connected to an FC Switch Module is not recognized normally by OS or
cannot be accessed after the Blade Enclosure (SIGMABLADE) is started, check the following and take
an appropriate action. See also the User's Guides of Blade Enclosure (SIGMABLADE), fibre channel
device, and those of applications you are using.
Check if the port data rate of connected fibre channel devices corresponds to that of the FC Switch
Module:
→ Refer to the User’s Guides of the connected fibre channel devices.
Check if the port topology of the connected fibre channel devices corresponds to that of the FC
Switch Module:
→ Refer to the User’s Guides of the connected fibre channel devices.
Check if the SFP modules and FC cables are connected securely:
→ Reconnect them securely.
Check if the FC Switch Modules recognize the connected devices:
→ See "Appendix Checking Connections of Peripherals" in this User’s Guide.
Check if the connected fibre channel devices are started and operated normally:
→ Check that devices are started and operated normally according to the User’s Guide of the
fibre channel devices.
Check if zoning is set normally
→ See "Setting zoning" described later to check that it is set normally.
Check if the fibre channel controllers operate on CPU blades normally.
→ Refer to the User’s Guides of the CPU blade and fibre channel controller to check if they
operate normally.
If fibre channel devices cannot be recognized despite the above checks,
consult with your service representative.
- 57 -
Download from Www.Somanuals.com. All Manuals Search And Download.
付録 シリアルポート接続
本製品はシリアルポート経由で装置コンソールにLoginし装置設定を実施する機能が内蔵されています。シ
リアルコンソールをご使用になるためには、事前に以下の作業の実施が必要になります。
<シリアルコンソール接続>
ブレード収納ユニット(SIGMABLADE)・EMカードのコンソールより本製品のシリアルコンソールにLogin
する必要があります。ブレード収納ユニット(SIGMABLADE)・EMカードのコンソールLogin方法に関しては各
ブレード収納ユニット(SIGMABLADE)およびEMカードのユーザーズガイドを参照願います。
本製品に設けられているシリアルポートに接続する為のパラメータは以下の通りです。
通信速度
データ長
9600 bps
8 bits
無し
パリティ
ストップビット
フロー制御
1 bit
None
本製品コンソールへの初期のLoginユーザー名及びパスワードは以下となります。
管理者権限:装置設定等の表示、設定変更が可能です。
装置Loginユーザー名:admin
装置Loginパスワード:password
ユーザー権限:装置設定等の表示が可能です。
装置Loginユーザー名:user
装置Loginパスワード:password
【注意】
装置Loginユーザー名/装置Loginパスワードは小文字で入力願います。
ブレード収納ユニット(SIGMABLADE)・EMカードのEther経由での本製品へ
ヒント
のシリアルLoginの方法に関してはブレード収納ユニット(SIGMABLADE)およ
びEMカードのユーザーズガイドを参照してください。
- 58 -
Download from Www.Somanuals.com. All Manuals Search And Download.
付録 周辺機器接続確認
本製品のコンソールにLoginし周辺機器の接続状態を確認します。
<Fibre Channel機器Linkup確認>
コンソールに“switchshow”コマンドを入力することにより現在の本製品へのFibre Channel
機器の接続状態を表示することが可能です。
・コンソール上で“switchshow”を入力してください。
“switchshow“表示画面例>
WH040000363:admin> switchshow
switchName:
switchType:
switchState:
switchMode:
switchRole:
switchDomain:
switchId:
WH040000363
43.1
Online
Native
Principal
1
fffc01
switchWwn:
zoning:
10:00:00:05:1e:02:04:09
OFF
OFF
switchBeacon:
Area Port Media Speed State
==============================
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
--
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
id
id
--
--
--
--
--
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
No_Module (No POD License) Disable
Online
F-Port 10:00:00:00:c9:51:fe:55
F-Port 10:00:00:00:c9:51:fg:99
F-Port 10:00:00:00:c9:51:fe:66
F-Port 10:00:00:00:c9:51:ff:28
F-Port 10:00:00:00:c9:51:fe:35
Disabled (Persistent)
Online
Online
Online
Online
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
Online
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
23 23
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
F-Port 20:05:00:30:13:84:04:6c
F-Port 20:06:00:30:13:84:04:6c
Online
No_Module
No_Module
No_Module (No POD License) Disable
No_Module (No POD License) Disable
No_Module (No POD License) Disable
WH040000363:admin>
N8406-019でご利用可能なポートは内部ポート ポート番号1~8、外部ポート ポー
ト番号 17~20 です。他のポートは状態表示は実施されますがご利用いただけませ
ん。N8406-020 に関しては全てのポートがご利用いただけます。
重要
“switchshow”コマンドで本製品に接続した装置の Linkup 情報が表示されること
を確認してください。表示されていないFibre Channel機器があった場合、接続し
ているFibreChannel機器及びSFPモジュール、FCケーブル等に障害が発生してい
る可能性があります。
- 59 -
Download from Www.Somanuals.com. All Manuals Search And Download.
“switchshow“表示内容
表示
状態
装置の各ポート番号に対応
Port
0~23
ポートにSFPモジュールが実装されていない。
(外部ポートのみ表示)
--
Media
Copper タイプのメディアが実装されている。
(内部ポートは固定)
Cu
id
2G
4G
FibreタイプのSFPモジュールが実装されている
ポートデータレートが2Gbps固定
ポートデータレートが4Gbps固定
Speed
No_Module SFPモジュールが実装されていない
Fibre Channel機器が正常にLinkupしている
接続しているFibreChannel機器のポートトポロジー
の状態により正常Linkup時は以下の3種類の表示を
行います。
Online
State
Fabricで接続 :Online F-Port WWN
Loopで接続 :Online L-Port 1Pubric
Cascadeで接続:Online E-Port WWN
SFP モジュールが光信号を受信しているが Fibre
Channel機器が正常にLinkupしていない
SFPモジュールが光信号を受信していない
No_Sync
No_light
“switchshow”により表示した情報と実際の接続情報を比較することによ
り障害箇所を特定することが可能です。
ヒント
N8406-019 でご利用可能できないポートの state 表示は、内部ポートは“No_Sync
Disabled (Persistent)”、外部ポートは“No_Module (No POD License) Disable”
が表示されます。
重要
- 60 -
Download from Www.Somanuals.com. All Manuals Search And Download.
<Fibre Channel機器Name Server登録確認>
コンソールに“nsshow”コマンドを入力することにより現在の本製品のName Serverに登録され
ているFibre Channel機器を確認することが可能です。
・コンソール上で“nsshow”を入力してください。
“nsshow“表示画面例>
WH040000363:admin> nsshow
{
Type Pid
COS
PortName
NodeName
TTL(sec)
N
010500;
2,3;10:00:00:00:c9:51:fe:97;20:00:00:00:c9:51:fe:97; na
FC4s: FCIP FCP
NodeSymb: [39] "Emulex LPe1105-NEC FV2.50A8 DV5-1.20A3 "
Fabric Port Name: 20:05:00:05:1e:02:04:09
Permanent Port Name: 10:00:00:00:c9:51:fe:97
N
011100;
3;20:05:00:30:13:84:04:6c;20:00:00:30:13:84:04:6c; na
iStorage 1000 1400]
FC4s: FCP [NEC
Fabric Port Name: 20:11:00:05:1e:02:04:09
Permanent Port Name: 20:05:00:30:13:84:04:6c
The Local Name Server has 2 entries }
WH040000363:admin>
“nsshow”コマンドで本製品に Linkup した装置の各種情報が表示されることを確
認してください。表示されていないFibre Channel機器があった場合、接続してい
るFibreChannel機器及びSFPモジュール、FCケーブル等に障害が発生している可
能性があります。
重要
表示される情報の詳細な内容に関しては接続しているFibre Channel機器のユーザ
ーズガイドを参照してください。
“nsshow“表示内容
表示
ポートの状態を表示します。
“N”はN_Port、“NL”はNL_Port、Uは不明な状態となります。
24BitのFibre Channel IDを表示しています。
Type
PID
6桁の数字で表されPIDが“xxyyzz”の場合以下の表示となります。
xx = SwitchのDomain ID
yy = ポート番号(16進表示で表示されます)
zz = Loop ID(Fabric 接続時は“00“となります)
接続したFibre Channel機器のWorld Wide Port Nameを表示します
接続したFibre Channel機器のWorld Wide Node Nameを表示します
PortName
NodeName
“nsshow”により本製品に接続した Fibre Channel 機器の WWPn を確認する
ことが可能です。周辺機器の各種設定に利用が可能です。
ヒント
“PID”はご使用になるOS種別によってはOSがDisk Array装置を認識する論理の
ハードウェアパスに影響します。システム運用開始後のPIDが変更になるような作
業を実施される場合はご注意ねがいます。
重要
影響のある作業:
Domain IDの変更/接続機器のポートトポロジーの変更
- 61 -
Download from Www.Somanuals.com. All Manuals Search And Download.
付録 カスケード接続
本製品においては N8406-*** 同士を接続するカスケード機能をサポートしています。
以下に本製品のカスケード機能に関し記載いたします。
<カスケード接続について>
本製品のカスケード機能に関しては以下の特徴があります。
・カスケードを実施したスイッチモジュールそれぞれに接続された外部デバイスを共有することが
可能となります。
・カスケードを実施したスイッチモジュールそれぞれに接続された CPU ブレードを共有することが可
能になります。
・カスケード機能は3Hopまでのサポートとなります。
・カスケードを実施したスイッチモジュール間でのZoningが実施できます。
・カスケードを実施し Fabric を構築した場合、Fabric 中の 1 台のスイッチが Fabric の最上位スイッ
チ(Principalスイッチ)として動作します。(単体スイッチは全てPrincipalスイッチとして動作)
・Fabric 中では Principal スイッチ以外の全てのスイッチは下位スイッチ(Subordinate スイッチ)と
して動作します。
“fabricprincipal”によりFabric中のPrincipalスイッチを任意のスイッ
チに設定することが可能です。
ヒント
スイッチ間を接続するカスケードパスは複数本接続することが可能です。
カスケードパスの冗長化、スイッチ間経路の冗長化を実施する事によりカス
ケードパス単一障害時のFabricへの影響を除去することが可能です。
カスケードを実施したスイッチモジュール間の最大転送レートは1カスケードパ
ス当たり4Gbpsとなります。
重要
4Hop以上のカスケード接続はサポートされません。
本製品がカスケード接続可能な製品はN8406-019/020のみとなります。他の製品と
のカスケード接続はサポートされません。
同一ブレード収納ユニット(SIGMABLADE)内の FC スイッチとのカスケード接続はで
きません。
カスケード接続を実施することによりスイッチモジュールにおけるスイッチの役
割(Principal/Subordinate)が変更(Fabricの再構築)される場合があります。
カスケード実施時には接続したスイッチ内で Fabric の構築処理が実施されます。
Fabricの構築処理(再構築処置を含む)が行われた場合Fabric内で処理されてい
るI/Oに影響が発生する可能性があります。
カスケードパス障害発生により Fabric から Principal スイッチが切り離される場
合、Fabricの再構築が実施されます。
カスケードパス冗長化、スイッチ間経路の冗長化を実施している場合でも
Principalスイッチ本体に障害が発生、FabricよりPrincipalスイッチが切り離さ
れる場合は、他のスイッチでFabricの再構築が行われます。
カスケード接続したスイッチで ZONING 設定を実施する場合、スイッチ間を接続す
るカスケードパスで利用するポートは ZONE 設定する必要はありません。カスケー
ドパスは全てのZONEで有効となります。カスケードパスでご利用のポートをZONE
に含みZONINGを実施した場合デバイス認識障害の発生原因となります。
- 62 -
Download from Www.Somanuals.com. All Manuals Search And Download.
以下の手順に従って、本製品同士をカスケード接続します。
1. カスケードを実施するスイッチの実装位置及び接続するポートにSFPモジュールが実装されて
いることを確認してください。
SFPモジュール未実装である場合は実装してください。
2. 追加接続するスイッチモジュールの内部設定を確認する。
Zoning 設定が実施されていないこと。Zoning 設定が実施されている場合は必ず Zone
Configurationを無効とし、Zone Configurationを全て削除してください。
Zone Configrationを削除した後は“cfgSave“コマンドでZone Configurationの変更を保
存してください。
※ ZONE情報の削除の方法に関しては“付録 装置設定機能中のZONING設定”を参照してください。
稼働中のスイッチモジュールに新規導入のスイッチモジュールをカスケー
ヒント
ド接続する場合、追加接続を実施するスイッチモジュールの ZONE 情報のみ
削除を実施してください。
稼働中のシステムで利用しているスイッチモジュールのZONE情報を削除した場合、
システム障害、データ破壊等の原因となります。運用中のシステムにおいてはスイ
ッチモジュールのZONE情報削除は実施しないでください。
重要
カスケードを実施することにより稼働中のスイッチモジュール内に設定されてい
るZONE情報がカスケード接続されたスイッチモジュールに伝播し有効となります。
3. 接続するスイッチモジュールを“switchdisable”コマンドで無効化してください。
WH040000557:admin>
WH040000557:admin> switchdisable
WH040000557:admin>
4. 接続するスイッチモジュールのDomain IDを変更してください。
※ Domain IDの変更方法に関しては“付録 装置設定機能中のDomain ID設定機能”を参照してく
ださい。
5. 接続するスイッチモジュール間をFCケーブルで接続する。
6. 無効化状態のスイッチモジュールを“switchenable”コマンドで有効化してください。
WH040000557:admin>
WH040000557:admin> switchenable
WH040000557:admin>
7. 接続したスイッチモジュールの有効化が終了した後、それぞれのスイッチで“switchshow“コ
マンドを実施し、スイッチ間のカスケードパスの接続状態を確認してください。
- 63 -
Download from Www.Somanuals.com. All Manuals Search And Download.
WH040000557:admin>switchshow
↓ (省略)
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
23 23
cu
cu
id
id
--
id
--
--
--
4G
4G
4G
4G
4G
4G
4G
4G
4G
No_Sync
Disabled (Persistent)
Disabled (Persistent)
No_Sync
No_Light
No_Light
No_Module
Online
E-Port 10:00:00:05:1e:03:55:f9 "WH040000642" (upstream)
No_Module
No_Module
No_Module
WH040000557:admin>
カスケードパスが正常にLinkできた場合の接続ポートのStatus表示は以下
の状態のいずれかになります。
E-Port WWN "Switch Name" (upstream)
ヒント
E-Port WWN "Switch Name" (downstream)
同一スイッチモジュール間に複数のカスケードパスを接続した場合、2本目
以降のカスケードパスは(upstream)、(downstream)の表示は行われません。
上記以外の Status 表示が実施された場合はカスケード接続時に不具合を検
出しています、作業を最初からやり直してください。
表示例:Domain ID 重複>
Online
E-Port segmented,(domain overlap)
接続を実施する側のスイッチモジュールに関しては Zoning 設定を必ず削除を実施
した後カスケード接続を実施してください。Zoningを実施した状態でのカスケード
作業は障害発生の原因となります。
重要
カスケードするスイッチの Domain ID が重複した ID である場合、カスケード接続
が実施できません。必ずカスケード実施時はスイッチモジュールのDomain IDが重
複しないようDomain IDの変更を実施してください。
カスケードしたスイッチ間の転送速度は1パス辺り4Gbpsとなります。
カスケード構成をご利用になる場合、スイッチモジュール間の転送速度の上限をご
理解の上システム構築を実施願います。
8. スイッチを3台以上カスケード接続した場合“fabricshow“コマンドを実施し、スイッチモジ
ュール間のカスケード接続状態の確認を実施してください。
WH040001124:admin> fabricshow
Switch ID
Worldwide Name
Enet IP Addr
FC IP Addr
Name
-------------------------------------------------------------------------
1: fffc01 10:00:00:05:1e:03:55:d8 192.168.1.32
2: fffc01 10:00:00:05:1e:03:43:25 192.168.1.33
3: fffc03 10:00:00:05:1e:03:32:3a 192.168.1.34
0.0.0.0
0.0.0.0
0.0.0.0
" WH040001100"
" WH040001945"
>"WH040001124"
The Fabric has 3 switches
WH040001124:admin>
正常にスイッチモジュールがカスケード接続できている場合、接続されてい
るスイッチそれぞれのDomainID/WWN/IPAddress/スイッチName情報が表示
されます。(FC IPは本機では利用しません。)
ヒント
- 64 -
Download from Www.Somanuals.com. All Manuals Search And Download.
<カスケード接続例>
ブレード収納ユニット#1 のスイッチのみに Principal スイッチ(最上位スイッチ)
の設定を必ず実施してください。Principal スイッチの設定方法に関しては、付録
装置設定機能中のPrincipal Selection Mode 確認/設定を参照してください。
重要
スイッチ(ブレード収納ユニット)2台をカスケードする場合:
(1) スイッチ間1パス構成
ブレード収納ユニット #1
ブレード収納ユニット #2
スイッチ間をカスケードしているパスに異常が発生した場合、Fabricの再構成が発
生します、カスケードスイッチ間のみでなく各スイッチ(各収納ユニット)に閉じ
て実施中のI/Oに影響が発生する可能性があります。
重要
(2) スイッチ間2パス構成
ブレード収納ユニット #1
ブレード収納ユニット #2
スイッチ間のカスケードパスを2重化することによりカスケードパス1本に異常が
発生した場合でも冗長パスにより継続動作し Fabric の再構成が発生しないため、
実施中のI/Oへの影響はありません。
重要
- 65 -
Download from Www.Somanuals.com. All Manuals Search And Download.
スイッチ(ブレード収納ユニット)3台をカスケードする場合:
(1) カスケードパス最小構成
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
スイッチ間をカスケードしているパスに異常が発生した場合、Fabricの再構成が発
生します、カスケードスイッチ間のみでなく各スイッチ(各収納ユニット)に閉じ
て実施中のI/Oに影響が発生する可能性があります。
重要
(2) カスケードパス2重化構成
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
スイッチ間のカスケードパスを2重化することによりカスケードパス1本に異常が
発生した場合でも冗長パスにより継続動作し Fabric の再構成が発生しないため、
実施中のI/Oへの影響はありません。
重要
- 66 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) 各スイッチ間、代替パスあり
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
3台のスイッチ間にカスケードパスを設定しているため、カスケードパス1本に異
常が発生した場合でも代替パスによるスイッチ間通信が可能であり Fabric の再構
成が発生しないため各収納ユニットで実施中のI/Oへの影響はありません。
重要
スイッチ(ブレード収納ユニット)4台をカスケードする場合:
(1) カスケードパス最小構成
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
ブレード収納ユニット #4
スイッチ間をカスケードしているパスに異常が発生した場合、Fabricの再構成が発
生します、カスケードスイッチ間のみでなく各スイッチ(各収納ユニット)に閉じ
て実施中のI/Oに影響が発生する可能性があります。
重要
- 67 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) カスケードパス2重化構成
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
ブレード収納ユニット #4
スイッチ間のカスケードパスを2重化することによりカスケードパス1本に異常が
発生した場合でも冗長パスにより継続動作し Fabric の再構成が発生しないため、
実施中のI/Oへの影響はありません。
重要
(3) 各スイッチ間、代替パスあり
ブレード収納ユニット #1
ブレード収納ユニット #2
ブレード収納ユニット #3
ブレード収納ユニット #4
4台のスイッチ間全てにパスが冗長構成設定しているため、カスケードパス1本に
異常が発生した場合でも代替パスによるスイッチ間通信が可能であり Fabric の再
構成が発生しないため各収納ユニットで実施中のI/Oへの影響はありません。
重要
- 68 -
Download from Www.Somanuals.com. All Manuals Search And Download.
付録 装置設定機能
本製品をご利用になるにはコンソールにLoginし装置設定を実施する必要があります。本製品のご利用に必
要な設定に関し以下に記載いたします。
内部機能設定に関しては本書を熟読し十分に機能を理解した上で実施をお願いい
たします。
重要
システム運用中の設定変更の実施は稼働中のシステムに影響を与える場合があり
ます。変更内容を十分に検討し作業の実施をしていただくようお願いいたします。
PASSWORD設定変更
本製品のコンソールにLoginが完了しましたら以下の手順に従い、本製品のPASSWORD設定変更を実
施してください。(設定変更は任意となります)
1> コンソール画面上で“passwd”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 下記メッセージが表示されますのでメッセージに従い、「従来のパスワード」、「変更するパスワー
ド」、「変更するパスワード」の再入力を実施してください。
WH040000363:admin> passwd
Changing password for admin
Enter old password:
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Saving password to stable storage.
Password saved to stable storage successfully.
WH040000363:admin>
変更したパスワードは次回Login時より有効になります。
変更するワードは8文字以上、40文字以下の英数字である必要があります。
変更したパスワードの紛失にはご注意ねがいます。パスワード紛失時には保守作業
が必要となります。お買い求めの販売店または保守会社へご連絡をお願いいたしま
す。
重要
- 69 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ネットワーク設定変更
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品のネットワーク設定変更
を実施してください。(設定必須)
ネットワーク未設定の状態で本製品を同一ブレード収納ユニット(SIGMABLADE)で
複数枚ご利用になった場合、IPAddressの重複により思わぬ障害の原因となる可能
性があります。必ずIP Addressの変更を実施して使用願いますようお願いします。
重要
<工場出荷設定>
工場出荷時のネットワーク設定は以下の設定となっています。
Ethernet IP Address
Ethernet Subnet Mask
0.0.0.0
255.255.255.0
Fibre Channel IP Address 0.0.0.0
Fibre Channel Subnetmask 0.0.0.0
Gateway Address
0.0.0.0
ネットワーク設定を実施しネットワーク接続を可能にした後は、本製品のコ
ンソールにネットワーク経由でのLoginが可能になります。
ヒント
1> コンソール画面上で“ipaddrset”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> Ethernet IP Address~Gateway Addressの入力画面が表示されますので設定値を入力し<Enter>キー
を入力してください。
なお、設定値詳細に関してはネットワーク管理者にご確認をお願いいたします。
HW060000955:admin> ipaddrset
Ethernet IP Address [0.0.0.0]:192.168.1.15
Ethernet Subnetmask [255.255.0.0]:255.255.255.0
Fibre Channel IP Address [0.0.0.0]:
Fibre Channel Subnetmask [0.0.0.0]:
Gateway IP Address [0.0.0.0]:192.168.1.254
Issuing gratituous arp...Done.
IP address is being changed...Done.
Committing configuration...Done.
HW060000955:admin>
設定する IP Address に関してはブレード収納ユニット(SIGMABLADE)の IP
ヒント
Addressと同一Subnetmask上となるように設定をおねがいします。
- 70 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ネットワーク設定終了後、本製品ファームウェア中のネットワーク関連のデーモン
プログラムが自動で再起動を実施します。ネットワーク設定は本デーモンの自動再
起動終後すぐに有効となります。
重要
本製品へのネットワーク経由でのアクセスを実施する場合、ブレード収納ユニット
(SIGMABLADE)側の設定作業が必要になる場合があります。設定に関してはブレード
収納ユニット(SIGMABLADE)のユーザーズガイドを参照願います。
Fibre Channel IP Address及びFibre Channel Subnetmaskに関しては利用できま
せんので設定変更は実施しないでください。
システム運用中にネットワーク設定を変更した場合、ネットワーク関連のデーモン
プログラム再起動時に本製品に接続のホストのLog上にErrorメッセージが表示さ
れることがあります。
3> コンソール画面上で“ipaddrshow”を入力してください。
ネットワーク設定が表示されますので設定結果を確認してください。
WH040000363:admin> ipaddrshow
SWITCH
Ethernet IP Address: 192.168.1.15
Ethernet Subnetmask: 255.255.255.0
Fibre Channel IP Address: 0.0.0.0
Fibre Channel Subnetmask: 0.0.0.0
Gateway Address: 192.168.1.254
WH040000363:admin>
設定した内容を確認し間違いがある場合は、再度正しく設定をしなおしてく
ださい。
ヒント
- 71 -
Download from Www.Somanuals.com. All Manuals Search And Download.
スイッチネーム設定変更
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品のスイッチ名の設定変更
を実施してください。(設定任意)
スイッチネームは15文字までの英数字で設定が可能です。
スイッチ名の変更は初期導入時に実施をお願いします。システム運用中の設定変更
はシステムに思わぬ影響が発生する可能性があります。
重要
本製品のスイッチネームは本装置コンソールのプロンプトに表示されます。
ヒント
本製品はブレード収納ユニット(SIGMABLADE)に最大4枚実装可能です。本ス
イッチ名の変更は各種設定実施時の本製品コンソールへLoginした場合の各
スロットのスイッチを識別する場合等に利用可能です。
<工場出荷設定>
工場出荷時のスイッチ名の設定は本製品の製品管理番号を設定しています。
1> コンソール画面上で“switchname”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在設定されているスイッチネームが表示されます。
WH040000363:admin> switchname
WH040000363
WH040000363:admin>
3> コンソール画面上“switchname”コマンドでスイッチ名を変更します。
“switchname name”を入力しスイッチ名を変更します。
“name“は新規設定するスイッチ名を入力します。
WH040000363:admin> switchname slot1
slot1:admin>
スイッチ名の変更実施後はコンソールプロンプトの表示が設定変更したス
イッチ名に変更されます。
ヒント
4> コンソール画面上“switchname”コマンドで実施し、3>で変更したスイッチ名が表示されることを
確認してください。
- 72 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ポートデータレート設定変更
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品の各ポートのポートデー
タレートの設定変更を実施してください。(設定必須)
<工場出荷設定>
工場出荷時のポートデータレート設定は全ポート4Gbps固定設定となっています。
ポートデータレートに関しては接続するFibre Channel機器のポートデータレート
に合わせ本製品のポートデータレートを設定する必要があります。ポートデータレ
ートの設定が異なる場合、接続する Fibre Channel 機器が正常に Linkup できない
状態になります。接続するFibre Channel機器のポートデータレートに関しては接
続するFibre Channel機器のユーザーズガイドを参照願います。
重要
1> コンソール画面上で“portcfgshow”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在のポート設定状態が表示されます。
WH040000350:admin> portcfgshow
Ports of Slot 0
0 1 2 3
4 5 6 7
8 9 10 11
12 13 14 15
-----------------+--+--+--+--+----+--+--+--+----+--+--+--+----+--+--+--
Speed
4G 4G 4G 4G
ON .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. ON ON ON
.. .. .. ..
.. .. .. ..
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
.. ON ON ON
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
ON ON ON ON
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
ON ON ON ON
Trunk Port
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable.. .. ON ON
Ports of Slot 0 16 17 18 19
20 21 22 23
-----------------+--+--+--+--+----+--+--+--
Speed
4G 4G 4G 4G
.. ON ON ON
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. ON ON ON
ON .. .. ..
.. .. .. ..
.. .. .. ..
4G 4G 4G 4G
ON ON ON ON
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
Trunk Port
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent DisableON .. .. ..
where AN:AutoNegotiate, ..:OFF, ??:INVALID.
WH040000350:admin>
ポートの状態表示を実施した場合、N8406-019 においても利用できないポートを含
んだ全てのポートの情報が同時に表示されます。異常ではありません。
重要
- 73 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3> ポートスピードの変更方法に関しては以下の2種類の方法があります。
ご利用目的にあわせ実施方法を選択願います。
・全ポート一括変更
“switchcfgspeed x”を入力しポートデータレート設定を変更します。
“x“は設定するポートデータレートを入力します。
4Gbps = 4 / 2Gbps = 2
WH040000350:admin> switchcfgSpeed 4
WH040000350:admin>
本製品内の全ポート(外部ポート/内部ポート)全てのポートデータレート
を一括で設定変更できます。
ヒント
・ポート単位での変更
“portcfgspeed x y”を入力しポートデータレート設定を変更します。
“x“は設定を変更するポート番号を入力します。
N8406-019:内部ポート 1~8 / 外部ポート 17~20
N8406-020:内部ポート 1~16 / 外部ポート 17~23、0
“y“は設定するポートデータレートを入力します。
4Gbps = 4 / 2Gbps = 2
WH040000350:admin> portcfgspeed 17 2
WH040000350:admin>
本製品内の変更を実施したいポート1個単位での変更が可能となります。
ヒント
4> 設定変更が終了したら、“portcfgshow”を入力してください。
変更内容が反映されているか確認をしてください。変更した各ポートのデータレート表示が設定値
となっていれば終了です。
- 74 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ポートトポロジー設定変更
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品の外部ポート、各ポート
のポートトポロジーの設定変更を実施してください。(設定必須)
<工場出荷設定>
工場出荷時のポートトポロジー(Locked G_Port)設定は以下の設定となっています。
外部ポート:ON(有効:Fabricデバイスのみ接続可能)
内部ポート:・・(無効:トポロジーをAutoで選択)
ポートトポロジー設定に関しては接続するFibre Channel機器のポートトポロジー
設定に合わせ本製品のポートトポロジーを設定する必要があります。ポートトポロ
ジーの設定が異なる場合、接続する Fibre Channel 機器が正常に Linkup できない
状態になります。接続するFibre Channel機器のポートトポロジーに関しては接続
するFibre Channel機器のユーザーズガイドを参照願います。
重要
1> コンソール画面上で“portcfgshow”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在のポート設定状態が表示されます。
WH040000350:admin> portcfgshow
Ports of Slot 0
0 1 2 3
4 5 6 7
8 9 10 11
12 13 14 15
-----------------+--+--+--+--+----+--+--+--+----+--+--+--+----+--+--+--
Speed
4G 4G 4G 4G
ON .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. ON ON ON
.. .. .. ..
.. .. .. ..
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
.. ON ON ON
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
ON ON ON ON
4G 4G 4G 4G
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON ON ON ON
.. .. .. ..
.. .. .. ..
ON ON ON ON
Trunk Port
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable.. .. ON ON
Ports of Slot 0 16 17 18 19
20 21 22 23
-----------------+--+--+--+--+----+--+--+--
Speed
4G 4G 4G 4G
.. ON ON ON
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. ON ON ON
ON .. .. ..
.. .. .. ..
.. .. .. ..
4G 4G 4G 4G
ON ON ON ON
.. .. .. ..
.. .. .. ..
.. .. .. ..
ON .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
.. .. .. ..
Trunk Port
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent DisableON .. .. ..
where AN:AutoNegotiate, ..:OFF, ??:INVALID.
WH040000350:admin>
- 75 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ポートの状態表示を実施した場合、N8406-019 においても利用できないポートを含
んだ全てのポートの情報が同時に表示されます。異常ではありません。
重要
3> ポートトポロジーの変更を実施します。
・ポート単位での変更
“portcfggport x y”を入力しポートトポロジー設定を変更します。
“x“は設定を変更するポート番号を入力します。
N8406-019:外部ポート 17~20
N8406-020:外部ポート 17~23、0
“y“は設定するポートトポロジー固定の有効/無効の指定を入力します。
0 = 無効 / 1 = 有効
WH040000350:admin> portcfggport 17 1
WH040000350:admin>
本製品内の変更を実施したいポート1個単位での変更が可能となります。
ヒント
内部ポートのTopology固定設定は実施できません。
本設定を有効にしたポートはLoopデバイスの接続が実施できません。
接続デバイスのポートモードをFabric(PointtoPoint)で接続する場合、必ず本設
定を“有効”としご利用ねがいます。設定を“無効”状態でご利用になった場合接
続機器が正常に認識できない場合があります。
重要
スイッチモジュール間をカスケード接続しご使用になる場合、カスケードパスで利
用するポートは本設定を“有効”としご利用ねがいます。
4> 設定変更が終了したら、“portcfgshow”を入力してください。
変更が有効となっているか確認を実施します。変更した各ポートの表示が下記表示になっていれば
設定は終了です。
LockdG_Portの表示内容
G_Port固定に変更
G_Port固定を解除
ON
・・
- 76 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Domain ID設定変更
本製品のコンソールに Loginが完了しましたら以下の手順に従い、本製品の Domain IDの設定変更
を実施してください。
カスケード接続未実施時は設定変更は任意となり、カスケード接続実施時は設定変
更は必須となります。
重要
<工場出荷設定>
工場出荷時のDomain ID設定は1となっています。
Domain ID の変更は本製品導入時に実施をおねがいいたします。運用開始後の
Domain IDの変更はシステム障害の原因となります。
1> コンソール画面上で“switchdisable”を入力しスイッチモジュールをDisable状態にします。
HW060000955:admin> switchdisable
スイッチをDisableにすることによりスイッチに接続した全てのFibre Channel機
器の通信が出来ない状態になります。
重要
2> コンソール画面上で“configure”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
3> “configure”を入力しスイッチの設定入力機能を表示します。
「Fabric parameters」の設定実施/未実施を問いかけるメッセージが表示されます、“y”を入力し
てください。
HW060000955:admin> configure
Configure...
Fabric parameters (yes, y, no, n): [no] y
- 77 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4> 「Fabric parameters」の設定メニューで「Domain ID」の項目のみ変更する数値を入力し他のパラ
メータは<Enter>キーを入力してください。
設定変更例> 1(def) → 2
Fabric parameters (yes, y, no, n): [no] y
Domain: (1..239) [1] 2
R_A_TOV: (4000..120000) [10000]
E_D_TOV: (1000..5000) [2000]
WAN_TOV: (0..30000) [0]
MAX_HOPS: (7..19) [7]
Data field size: (256..2112) [2112]
Sequence Level Switching: (0..1) [0]
Disable Device Probing: (0..1) [0]
Suppress Class F Traffic: (0..1) [0]
Switch PID Format: (1..2) [1]
Per-frame Route Priority: (0..1) [0]
Long Distance Fabric: (0..1) [0]
BB credit: (1..27) [16]
5> 「Fabric parameters」の設定変更終了後、「Insistent Domain ID Mode」以降の設定実施/未実施を
問いかけるメッセージは全て“n”または<enter>を入力してください。
Insistent Domain ID Mode (yes, y, no, n): [no]
Virtual Channel parameters (yes, y, no, n): [no]
F-Port login parameters (yes, y, no, n): [no]
Zoning Operation parameters (yes, y, no, n): [no]
RSCN Transmission Mode (yes, y, no, n): [no]
Arbitrated Loop parameters (yes, y, no, n): [no]
System services (yes, y, no, n): [no]
Portlog events enable (yes, y, no, n): [no]
ssl attributes (yes, y, no, n): [no]
http attributes (yes, y, no, n): [no]
snmp attributes (yes, y, no, n): [no]
rpcd attributes (yes, y, no, n): [no]
cfgload attributes (yes, y, no, n): [no]
webtools attributes (yes, y, no, n): [no] WARNING: The domain ID will・・・・・・・
HW060000955:admin>
6> 本製品の機能を有効にするため“switchenable”を入力してください。
HW060000955:admin> switchenable
- 78 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Principal Selection Mode確認/設定
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品の Principla Selection
Modeの確認/設定を実施してください。
スイッチを単体でお使いになる場合は本設定は不要です。
重要
<工場出荷設定>
工場出荷時のPrincipal Selection Mode 設定はDisableとなっています。
Principal Selection Mode の設定変更は本製品導入時に実施をおねがいいたしま
す。運用開始後にPrincipalSelectionModeの変更を実施した場合、実施中のI/O
に影響が発生する場合があります。
状態確認:
1> コンソール画面上で“fabricprincipal”を入力し現在の設定状態を表示します。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
WH040001124:admin> fabricprincipal
カスケードを実施する全てのスイッチの Principal Selection Mode を確認してく
ださい。
重要
2> コンソール画面上に以下のメッセージが表示されます。
Principal Selection Mode 設定“Disable”の場合
WH040001124:admin> fabricprincipal
Principal Selection Mode: Disable
WH040001124:admin>
Principal Selection Mode 設定“Enable”の場合
※ コマンドを実施したスイッチの現在の状態により表示されるメッセージが異なります。
スイッチがPrincipal(最上位スイッチ)として動作している場合
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable (Switch currently principal)
WH040001124:admin>
スイッチが既にSubordinate(下位スイッチ)として動作している場合
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable
WH040001124:admin>
- 79 -
Download from Www.Somanuals.com. All Manuals Search And Download.
設定変更:
1> 設定を変更するスイッチモジュールにLoginしてください。
PrincipalSelectionModeの変更はLoginしているスイッチに対してのみ実施可能
です。
重要
2> コンソール画面上で“fabricprincipal –f 1”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
“fabricprincipal”コマンドに引数“-f”、“1”を付け実施することにより、コマ
ンドを入力したスイッチの Principal Selection Mode を Enable に変更、Fabric
中のPrincipalスイッチに変更するFabric再構築が実施されます。
Fabric中のスイッチにおいてPrincipal Selection Mode Enable設定するスイッチ
は1台のみととしてください。
重要
WH040001124:admin> fabricprincipal -f 1
Principal Selection Mode enabled (Forcing fabric rebuild)
WH040001124:admin>
3> コンソール画面上で“fabricprincipal”を入力しPrincipal Selection ModeがEnbaleになってい
る事を確認してください。
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable (Switch currently principal)
WH040001124:admin>
コマンドの実施結果上記メッセージが表示されない場合は“fabricprincipal–f1”
コマンドを再実行してください。
重要
WH040001124:admin> fabricprincipal -f 1
Principal Selection Mode enabled (Forcing fabric rebuild)
WH040001124:admin>
4> コンソール画面上で“switchshow”を入力し表示結果中のswitchRoleがPrincipalで表示されてい
ることを確認してください。
WH040001124:admin> switchshow
switchName:
WH040001124
43.2
switchType:
switchState:
switchMode:
Online
Native
switchRole:
Principal
3 (unconfirmed)
switchDomain:
switchId: fffc03
switchWwn: 10:00:00:05:1e:03:32:3a
zoning:
OFF
OFF
switchBeacon:
↓以下省略
- 80 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーニング設定
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品のゾーニングの設定を実
施してください。
なお、本製品のゾーニング機能には「WWNモードゾーニング」及び「ポートモードゾーニング」の2
種類の機能があります。
ご利用になるゾーニングの設定機能に関しては「ポートモードゾーニング」機能の
ご利用を強く推奨いたします。「WWNモードゾーニング機能」をご利用になった場合、
接続機器の保守交換実施時等、Fibre Channel 機器の交換毎にゾーニングの変更が
必要となります。「ポートモードゾーニング」機能をご利用の場合は保守交換時の
ゾーニングの再設定は不要となります。(ポート番号を変更しない場合)
ゾーニングの設定変更は十分にゾーニング機能を理解したうえで実施をお願いい
たします。また運用中のゾーニングの変更は思わぬシステム障害の原因となりま
す。ゾーニング変更時は変更の内容、実施方法及び影響の範囲を十分ご確認願い実
施いただきますようお願いたします。
重要
本製品の接続機器をゾーニングを実施し論理的に切り離すことにより、ゾーン外の
デバイスの Login/Logout 等 Fibre Channel 上の内部的な影響を排除することがで
きます。
本製品のコンソールにおけるコマンド入力は通信端末(VT100 エミュレータ)のフ
ァイル入力機能には対応しておりません。通信端末(VT100 エミュレータ)のファ
イル入力をご使用になった場合、装置障害が発生する場合があります。ファイル入
力は使用しないよう注意をお願いいたします。
カスケード機能をご利用の構成において、スイッチ間を接続するカスケードパスで
利用するポートはZONE設定する必要はありません。カスケードパスは全てのZONE
で有効となります。カスケードパスでご利用のポートをZONEに含みZONINGを実施
した場合デバイス認識障害の発生原因となります。
<工場出荷設定>
工場出荷時にはゾーニングの設定は実施されていません。
全ての接続デバイス間での通信が可能です。
<設定の流れ>
・現在のゾーニング設定の確認
・ゾーンエイリアス名の作成
・ゾーンの作成
(83ページ参照)
(84ページ参照)
(85ページ参照)
(89ページ参照)
(90ページ参照)
・コンフィグレーションの作成
・コンフィグレーションの有効化
<その他の設定>
・ゾーンエイリアスの修正・削除
・ゾーンの修正・削除
(92ページ参照)
(93ページ参照)
・コンフィグレーションの修正・削除 (94ページ参照)
・コンフィグレーションの無効化
・その他
(95ページ参照)
(96ページ参照)
- 81 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーニング関連コマンド
コマンド
alicreate
実行内容
指定したポート、WWPnを含んだゾーンエイリアスを作成
指定したゾーンエイリアスにポートまたは WWPn を追加
登録
aliadd
指定したゾーンエイリアスより指定したポートまたは
WWPnを削除
ゾーンエイリアス作成
alidelete
指定したゾーンエイリアスより指定したポートまたは
WWPnを削除
aliremove
alishow
登録済みのゾーンエイリアス情報を表示
指定したポート、WWPnを含んだゾーンを作成
指定したゾーンにポート、ゾーンエイリアス名又はWWPn
を追加登録
zonecreate
zoneadd
指定したゾーンより指定したポート、ゾーンエイリアス
またはWWPnを削除
ゾーン作成
zoneremove
zonedelete
zoneshow
指定したゾーンを削除
ゾーン情報を表示
指定したゾーンを含むゾーンコンフィグレーションを作
成
cfgcreate
cfgdelete
cfgclear
指定したゾーンコンフィグレーションを削除
スイッチ内のゾーニング関連の情報全てを削除
指定したゾーンコンフィグレーションに指定したゾーン
を追加
コンフィグファイル作成
cfgadd
指定したゾーンコンフィグレーションから指定したゾー
ンを削除
cfgremove
cfgenable
cfgdisable
cfgshow
指定したゾーンコンフィグレーションを有効にする。
有効となっているゾーンコンフィグレーションの無効化
コンフィグ情報を表示
コンフィグ操作
有効になっているゾーンコンフィグレーションの情報の
み表示
cfgactvshow
cfgsave
コンフィグレーションの変更内容の保存を実施
作成済みのゾーン名、ソーンコンフィグレーション名、
ゾーンエイリアス名の変更が可能
zoneobjectrename
指定したゾーン、ソーンコンフィグレーション、ゾーン
エイリアス名を抹消
その他
zoneobjectexpunge
zoneobjectcopy
指定したゾーン、ソーンコンフィグレーション、ゾーン
エイリアス情報をコピー
ゾーニング関連のコマンドには引数が必要になります。コマンドの使用方法詳細に
関しては各コマンドの説明を参照願います。
重要
ゾーニング作業の失敗はシステム障害の原因となります。ゾーニング実施に際はコ
マンド影響の範囲をご理解の上作業の実施をお願いいたします。
- 82 -
Download from Www.Somanuals.com. All Manuals Search And Download.
現在のゾーニング設定の確認:
1> コンソール画面上で“cfgshow”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在のゾーニング設定情報が表示されます。
ゾーニング情報がない場合:「ゾーンエイリアス名の作成」以降に進んでください。
ゾーニング情報がある場合:設定変更内容の再確認を実施し作業を実施願います。
ゾーニング情報なし>
WH040000350:admin> cfgshow
Defined configuration:
no configuration defined
Effective configuration:
no configuration in effect
WH040000350:admin>
ゾーニング情報あり>
WH040000350:admin> cfgshow
Defined configuration:
cfg:
zone_cfg
zone1; zone2
1,0; 1,1
zone:
zone:
zone1
zone2
1,4; 1,5
Effective configuration:
cfg:
zone_cfg
zone1
zone:
1,0
1,1
1,4
1,5
zone:
zone2
WH040000350:admin> cfgshow
有効状態のゾーニング情報が表示された場合の、ゾーニング設定変更作業実施時に
はご注意願います。変更後のコンフィグレーションを有効にした時点でゾーニング
設定が変更されます。ゾーニング変更前後で設定ミス等ある場合、システム障害の
原因となります。
重要
- 83 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーンエイリアス名の設定:
本製品に接続してあるFibre Channel機器の情報を任意の名称に変更することが可能です。
なお、一つのゾーンエイリアス名には本製品に接続されたFibreChannel機器のWWPn及び本製品の
ポート番号(Domain IDを含む)を指定することが可能です。
“alicreate”コマンドを使用しゾーンエイリアスを作成します。
“alicreate”コマンドの使用方法
alicreate “aliName”,”member;member”
^^^^^^^ ^^^^^^^^^^^^^
①
②
① – aliName :作成するゾーンエイリアス名を“”で囲んで指定する
② – member :ゾーンエイリアス名に含むメンバーを「,」で区切り指定する。
メンバーにはポート番号指定及びWWPnの指定が可能です。
※ aliNameとmemberの間は「,」で区切る
memberとmemberの間は「;」で区切る
1> コンソール画面上で“alicreate”コマンドを使用しゾーンエイリアスを作成してください。
WH040000350:admin> alicreate "ali1","1,0;1,1"
WH040000350:admin> alicreate "ali2","10:00:00:00:c9:4b:a1:e5;20:01:00:30:13:84:03:d2"
WH040000350:admin>
ゾーンエイリアス情報にはポート番号(DimainID含む)及びWWPnを同時に設定す
ることが可能です。
重要
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
作成したゾーンエイリアスはゾーン作成時の member として利用することが
可能です。
- 84 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーンの作成:
<ポートモードゾーニング>
ポートモードゾーニングではFCスイッチモジュールの「Domain ID」と「ポート番号」を使用し
ゾーニング設定を実施します。
1) Domain IDの確認
1> コンソール画面上で“switchshow”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> FCスイッチモジュールの状態に関する情報が表示されます。
「Domain ID」に関しては「switchDomain」の値を参照します。(出荷時設定 = 1)
WH040000350:admin> switchshow
switchName:
switchType:
switchState:
switchMode:
switchRole:
switchDomain:
switchId:
WH040000350
43.1
Online
Native
Principal
1
fffc01
switchWwn:
zoning:
10:00:00:05:1e:02:08:53
OFF
OFF
switchBeacon:
Area Port Media Speed State
==============================
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
--
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
id
id
id
id
--
--
--
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
No_Module (No POD License) Disabled
No_Sync
No_Sync
No_Sync
Online
Disabled (Persistent)
Disabled (Persistent)
F-Port 10:00:00:00:c9:51:fe:c0
Disabled (Persistent)
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
Online
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
(No POD License) Disabled (Persistent)
F-Port 20:01:00:30:13:84:09:42
F-Port 20:02:00:30:13:84:09:42
F-Port 20:05:00:30:13:84:09:42
F-Port 20:06:00:30:13:84:09:42
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
23 23
Online
Online
Online
No_Module (No POD License) Disabled
No_Module (No POD License) Disabled
No_Module (No POD License) Disabled
WH040000350:admin>
ポートモードゾーニングを実施した後、Domain ID の変更を実施した場合、変更後
のDomain IDでのゾーニングの再設定が必要になります。
重要
- 85 -
Download from Www.Somanuals.com. All Manuals Search And Download.
“switchshow”中の“switchname”の表示を確認しゾーニングを実施する対象装
置であることを確認してください。
チェック
2) Zoneの作成
“zonecreate”コマンドを使用しゾーンを作成します。
“zonecreate”コマンドの使用方法
zonecreate “zonename”,”member;member;member”
^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^
①
②
① – zonename:ゾーン名を“”で囲んで指定する
② – member :Domain IDとポート番号(10進)を「,」で区切り指定する
※ ゾーン名とポート指定の間は「,」で区切る
ポート指定とポート指定の間は「;」で区切る
ゾーン名は64文字以下の英数字が利用可能です。
重要
作成するゾーンの数、本コマンドを実施する必要があります。
1> コンソール画面上で“zonecreate”コマンドを使用しゾーンを作成してください。
WH040000350:admin> zonecreate "zone1","1,0;1,1"
WH040000350:admin> zonecreate "zone2","1,2;1,3"
WH040000350:admin> zonecreate "zone3","1,4;1,5"
WH040000350:admin> zonecreate "zone4","1,6;1,7"
WH040000350:admin>
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> コンソール画面上で“zoneshow”を入力してください。
WH040000350:admin> zoneshow
Defined configuration:
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
no configuration in effect
WH040000350:admin>
- 86 -
Download from Www.Somanuals.com. All Manuals Search And Download.
“zonecreate”コマンドで作成したゾーンが全て表示されることを確認してく
ださい。
チェック
ゾーン名の後にゾーンに含まれるポート指定が表示されます、設定したポート
指定が正しく表示されていることを確認してください。
<WWNモードゾーニング>
WWNモードゾーニングではFCスイッチモジュールに接続しているFibre Channel機器のWWPnを
使用しゾーニング設定を実施します。
1) WWPnの確認
1> ご利用になるFibre Channel機器のWWPnを確認してください。
ご利用になる Fibre Channel 機器の WWPn の確認方法に関しては製品に添付
されているユーザーズガイドを参照してください。
ヒント
2) Zoneの作成
“zonecreate”コマンドを使用しゾーンを作成します。
“zonecreate”コマンドの使用方法
zonecreate "zonename","member;member;member”
^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^
①
②
① - zonename:作成するゾーン名を“”で囲んで指定する
② – member :Fibre Channel機器のWWPn(World Wide Port Name)を指定する
※ ゾーン名とWWPn指定の間は「,」で区切る
WWPn指定とWWPn指定の間は「;」で区切る
1> コンソール画面上で“zonecreate”コマンドを使用しゾーンを作成してください。
WH040000350:admin> zonecreate "zone1","10:00:00:00:c9:4b:a1:e5;20:01:00:30:13:84:03:d2"
WH040000350:admin> zonecreate "zone2","10:00:00:00:c9:4b:a2:05;20:02:00:30:13:84:03:d2"
WH040000350:admin> zonecreate "zone3","10:00:00:00:c9:4b:a1:f6;20:05:00:30:13:84:03:d2"
WH040000350:admin> zonecreate "zone4","10:00:00:00:c9:4b:83:aa;20:06:00:30:13:84:03:d2"
WH040000350:admin>
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
ゾーン名は64文字以下の英数字が利用可能です。
重要
作成するゾーンの数、本コマンドを実施する必要があります。
- 87 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2> コンソール画面上で“zoneshow”を入力してください。
WH040000350:admin> zoneshow
Defined configuration:
zone: zone1 10:00:00:00:c9:4b:a1:e5; 20:01:00:30:13:84:03:d2
zone: zone2 10:00:00:00:c9:4b:a2:05; 20:02:00:30:13:84:03:d2
zone: zone3 10:00:00:00:c9:4b:a1:f6; 20:05:00:30:13:84:03:d2
zone: zone4 10:00:00:00:c9:4b:83:aa; 20:06:00:30:13:84:03:d2
Effective configuration:
no configuration in effect
WH040000350:admin>
“zonecreate”コマンドで作成したゾーンが全て表示されることを確認してく
ださい。
チェック
ゾーン名の後にゾーンに含まれるWWPnが表示されます、設定したWWPnが正し
く表示されていることを確認してください。
- 88 -
Download from Www.Somanuals.com. All Manuals Search And Download.
コンフィグレーションの作成:
ゾーニング設定を実施するため、先に作成したゾーンを含んだコンフィグレーションを作成する必
要があります。コンフィグレーションは複数作成可能です。
1) コンフィグレーションの作成
“cfgcreate”コマンドを使用しコンフィグファイルを作成します。
“cfgcreate”コマンドの使用方法
cfgcreate “cfgName”,”member;member;member”
^^^^^^^ ^^^^^^^^^^^^^^^^^^^^
①
②
① – cfgName:作成するゾーンコンフィグレーション名を“”で囲んで指定する
② – member :作成済みのゾーン名を“”で囲んで指定する
※ コンフィグレーション名とゾーン名の間は「,」で区切る
ゾーン名とゾーン名の間は「;」で区切る
1> コンソール画面上で“zoneshow”を入力してください。
WH040000350:admin> zoneshow
Defined configuration:
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
no configuration in effect
WH040000350:admin>
必要なゾーンが全て作成されていることを確認してください。
ヒント
必要であればゾーンを作成してくさい。
2> “cfgcreate”コマンドを使用しコンフィグレーションを作成してください。
WH040000350:admin>
WH040000350:admin> cfgcreate "cfg1","zone1;zone2;zone3;zone4"
WH040000350:admin>
ゾーン情報に登録されていないゾーン名を指定した場合本コマンドはエラーが発
生し正常にコンフィグレーションが作成されません。作成済みのゾーン名のみ指定
ねがいます。
重要
- 89 -
Download from Www.Somanuals.com. All Manuals Search And Download.
コンフィグレーションの有効化:
作成したコンフィグレーションを有効にします。なお、同時に有効化を実施できるコンフィグレー
ションは1個となります。
1) コンフィグレーションの有効化
“cfgenable”コマンドを使用しコンフィグレーションを有効にします。
“cfgenable”コマンドの使用方法
cfgenable “cfgName”
^^^^^^^
①
① – cfgName:ゾーンコンフィグレーション名を“”で囲んで指定する
“cfgenable”コマンドでコンフィグレーションを有効にする場合。コンフィグレ
ーションを有効にするかを問いかけるメッセージが表示されます。有効とする場合
は“y”を有効にしない場合は“n”を入力します。
重要
メッセージ例:
Do you want to enable 'cfg1' configuration (yes, y, no, n): [no]
1> コンソール画面上で“cfgshow”を入力してください。
WH040000350:admin> cfgshow
Defined configuration:
cfg:
cfg1
zone1; zone2; zone3; zone4
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
no configuration in effect
WH040000350:admin>
“Defined Configuration”内に有効にするコンフィグレーションがあるこ
とを確認してください。
ヒント
必要であればコンフィグレーションを作成してくさい。
- 90 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2> “cfgenable”コマンドを使用しコンフィグレーションを有効にします。
WH040000350:admin> cfgenable "cfg1"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'cfg1' configuration (yes, y, no, n): [no] y
zone config "cfg1" is in effect
Updating flash ...
WH040000350:admin>
ゾーン情報に登録されていないコンフィグレーション名を指定した場合本コマン
ドはエラーが発生しコンフィグレーションが有効にできません。作成済みのコンフ
ィグレーション名のみ指定願います。
重要
3> “cfgactvshow”コマンドを使用しコンフィグレーションが有効になったことを確認します。
「EffectiveConfiguration」表示の下に有効になっている「コンフィグレーション名」と有効にな
っている「ゾーン名」、ゾーンに含まれる「ポート情報、WWPn情報、ゾーンエイリアス名」が表示さ
れます。
WH040000350:admin> cfgactvshow
Effective configuration:
cfg:
cfg1
zone: zone1
zone: zone2
zone: zone3
zone: zone4
1,0
1,1
1,2
1,3
1,4
1,5
1,6
1,7
有効にしたゾーン情報に設定ミス等があった場合はコンフィグレーションを無効
にし、ゾーニング情報の修正を実施してください。
重要
- 91 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーンエイリアス情報の修正・削除:
作成済みのゾーンエイリアス情報の修正及び削除の方法をご説明します。
各コマンドで修正を実施した後は“alishow”コマンドを使用し修正が正常に実施
されていることを確認してください。
重要
1) ゾーンエイリアスに追加情報を登録します。
“aliadd”コマンドを使用します。
“aliadd”コマンドを使用し指定したゾーンエイリアスに追加情報(ポート情報/WWPn)を追加登録
できます。
aliadd “aliname”,”member” <enter>
^^^^^^ ^^^^^^
①
②
① – aliname:ゾーンエイリアス名を“”で囲んで指定する
② – member :ポート指定、WWPnを指定する
※ ゾーン名と追加情報の間は「,」で区切る
各追加情報の間は「;」で区切る
2) ゾーンエイリアスから情報を削除する
“aliremove”コマンドを使用します。
“aliremove”コマンドを使用し指定したゾーンエイリアスより指定した登録済み情報(ポート情報
/WWPn)を削除できます。
aliremove “aliname”,”member” <enter>
^^^^^^^ ^^^^^^
①
②
① -aliname:ゾーンエイリアス名を“”で囲んで指定する
② – member :削除するポート指定、WWPnを指定する
※ ゾーン名と追加情報の間は「,」で区切る
各削除情報の間は「;」で区切る
3) 作成済みのゾーンエイリアスを削除する
“alidelete”コマンドを使用します。
“alidelete”コマンドを使用し登録済みのゾーンエイリアスを削除します。
alidelete “aliname” <enter>
^^^^^
①
① -aliname :ゾーンエイリアス名を“”で囲んで指定する
- 92 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ゾーンの修正・削除:
作成済みのゾーンの修正及び削除の方法をご説明します。
各コマンドで修正を実施した後は“zoneshow”コマンドを使用し、修正が正常に実
施されていることを確認してください。
重要
1) ゾーンへポート情報、WWPn、ゾーンエイリアス名を追加する
“zoneadd”コマンドを使用します。
“zoneadd”コマンドを使用し追加情報(ポート情報/WWPn/ゾーンエイリアス名」をゾーンに追加で
きます。
zoneadd “zonename”,”member” <enter>
^^^^^^^^ ^^^^^^
①
②
① – zonename:ゾーン名を“”で囲んで指定する
② – member :ポート指定、WWPnまたはゾーンエイリアスを指定する
※ ゾーン名と追加情報の間は「,」で区切る
各追加情報の間は「;」で区切る
2) ゾーンからポート情報、WWPn、ゾーンエイリアス名を削除する
“zoneremove”コマンドを使用します。
“zoneremove”コマンドを使用しポート情報、WWPn、ゾーンエイリアス名をゾーンから削除します。
zoneremove “zonename”,”member” <enter>
^^^^^^^^ ^^^^^^
①
②
① -zonename:ゾーン名を“”で囲んで指定する
② – member :ポート指定、WWPnまたはゾーンエイリアスを指定する
※ ゾーン名と追加情報の間は「,」で区切る
各削除情報の間は「;」で区切る
3) 作成済みのゾーンを削除する
“zonedelete”コマンドを使用します。
“zonedelete”コマンドを使用しゾーンを削除します。
zonedelete “zonename” <enter>
^^^^^^^^
①
① -zonemame :ゾーン名を“”で囲んで指定する
- 93 -
Download from Www.Somanuals.com. All Manuals Search And Download.
コンフィグファイルの修正・削除:
作成済みのコンフィグレーションの修正及び削除の方法をご説明します。
各コマンドで修正を実施した後は“zoneshow”コマンドを使用し修正が正常に実施
されていることを確認してください。
重要
1) ゾーンコンフィグレーションへのゾーンの追加
“cfgadd”コマンドを使用します。
“cfgadd”コマンドを使用しゾーンコンフィグレーションへゾーンを追加できます。
“cfgadd”コマンドの使用方法
cfgadd “cfgNeme”,”member” <enter>
^^^^^^^ ^^^^^^
①
②
① – cfgName:ゾーンコンフィグレーション名を“”で囲んで指定する
② – member :追加するゾーン名を“”で囲んで指定する
2) ゾーンコンフィグレーションからゾーンを削除
“cfgremove”コマンドを使用します。
“cfgremove”コマンドを使用しゾーンコンフィグレーションからゾーンを削除します。
“cfgremove”コマンドの使用方法
cfgremove “cfgName”,”member” <enter>
^^^^^^^ ^^^^^^
①
②
① – cfgName:ゾーンコンフィグレーションを“”で囲んで指定する
② – member :削除するゾーン名を“”で囲んで指定する
3) 作成済みのコンフィグファイルを削除
“cfgdelete”コマンドを使用します。
“cfgdelete”コマンドを使用し指定したゾーンコンフィグレーションが削除できます。
“cfgdelete”コマンドの使用方法
cfgremove “cfgName” <enter>
^^^^^^^
①
① – cfgName:ゾーンコンフィグレーションを“”で囲んで指定する
- 94 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4) 全てのゾーニング情報を削除する。
“cfgclear”コマンドを使用し全てのゾーニング情報が削除できます。
“cfgclear”コマンドを使用しゾーンコンフィグレーションを削除します。
“cfgclear”コマンドの使用方法
cfgclear <enter>
“cfgclear”コマンド実施前に“cfgdisable“コマンドを使用し有効となっている
ゾーン情報を無効にする必要があります。“cfgclear”コマンドでゾーニング情報
の削除は実施できますが、“cfgclear”コマンドを実施した時点で有効となってい
るゾーニングは“cfgclear”コマンド実施以降も有効となります。
重要
コンフィグレーションの保存/無効化:
コンフィグレーション変更後の保存方法及び有効になっているコンフィグファイルを無効にする
方法をご説明します。
1) 変更を実施したコンフィグレーションを保存する
“cfgsave”コマンドを使用する
“cfgsave”コマンドを使用し変更したコンフィグレーション情報を保存します。
“cfgsave”コマンドの使用方法
cfgsave <enter>
“cfgsave”コマンド実施することによりコマンド実施時点で変更されているコン
フィグレーション情報を保存します。本コマンドでコンフィグレーションを保存す
ることにより装置リブート後も設定したコンフィグレーションが有効になります。
重要
2) 有効状態のコンフィグファイルを無効にする
“cfgdisable”コマンドを使用する
“cfgdisable”コマンドを使用し有効となっているコンフファイルを無効にします。
“cfgdisable”コマンドの使用方法
cfgdisable <enter>
“cfgdisable”コマンド実施することによりコマンド実施時点で有効になってい
るゾーンコンフィグレーション全てが無効になります。
重要
- 95 -
Download from Www.Somanuals.com. All Manuals Search And Download.
その他:
作成済みの各種ゾーンオブジェクト名の変更、オブジェクトの抹消、オブジェクトのコピー方法を
ご説明します。
各コマンドで修正を実施した後は“cfgshow”コマンドを使用し修正が正常に実施
されていることを確認してください。
重要
各コマンド実施後は設定変更を本製品に登録するため“cfgsave”コマンドを実施
してください。
1) 作成済みオブジェクトの名前の変更
“zoneobjectrename”コマンドを使用します。
“zoneobjectrename”コマンドを使用しゾーンオブジェクト名を変更できます。
“zoneobjectrename”コマンドの使用方法
zoneobjectrename “objectNeme”,”newName” <enter>
^^^^^^^^^^ ^^^^^^^
①
②
① – objectName:変更する既存のオブジェクト名を“”で囲んで指定する
② – newName :変更後のオブジェクト名を“”で囲んで指定する
2) オブジェクトの末梢
“zoneobjectexpunge”コマンドを使用します。
“zoneobjectexpunge”コマンドを使用し指定したオブジェクトを抹消します。
“zoneobjectexpunge”コマンドの使用方法
zoneobjectexpunge “objectName” <enter>
^^^^^^^^^^
①
① – objectName:抹消する既存のオブジェクト名を“”で囲んで指定する
3) 作成済みオブジェクトのコピー
“zoneobjectcopy”コマンドを使用します。
“zoneobjectcopy”コマンドを使用しゾーンオブジェクト名をコピーできます。
“zoneobjectcopy”コマンドの使用方法
zoneobjectcopy “objectNeme”,”newName” <enter>
^^^^^^^^^^ ^^^^^^^
①
②
① – objectName:コピーする既存のオブジェクト名を“”で囲んで指定する
② – newName :コピーのオブジェクト名を“”で囲んで指定する
- 96 -
Download from Www.Somanuals.com. All Manuals Search And Download.
時刻設定/タイムサーバー設定
本製品のコンソールに Login が完了しましたら以下の手順に従い、本製品の内蔵時計の設定を実施
してください。
本製品の内蔵時計の時刻設定を事前に行うことにより障害発生時の調査時、他の機
器のLOGとの時間比較が可能となります。本件ご理解の上設定の実施をお願いしま
す。
重要
本製品をご利用になる環境にタイムサーバーをご利用できる環境がある場
合タイムサーバーをご利用になることが可能です。タイムサーバーをご利用
になる場合は時刻設定を実施せず、タイムサーバの設定のみ実施願います。
ヒント
<時刻設定>
1> コンソール画面上で“date”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在の本製品の時間内部時間が表示されます。
UTC表示例>
WH040000350:admin> date
Wed Jun 27 13:07:46 UTC 2006
WH040000350:admin>
Local表示例>
WH040000350:admin> date
Wed Nov 27 22:07:46 Localtime 2006
WH040000350:admin>
3> 時刻表示が“UTC”表示の場合“tstimezone”コマンドでUTC(世界協定時刻)との時差設定をしま
す。表示が“Localtime”で表示された場合は4>にお進みください。
UTCとの時差は“+9”時間です。
WH040000350:admin> tstimezone 9
Updating Time Zone configuration...done.
System Time Zone change will take effect at next reboot.
WH040000350:admin>
本製品の内蔵時計の基準時刻はUTC時刻を基準とし、UTC時刻との時差を設定する
ことにより“Localtime”表示に切り替わります。
重要
- 97 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4> “date ”コマンドで、内蔵時計の時刻をあわせます。
時刻設定例:
WH040000350:admin> date "0627220706"
Wed Junv 27 22:07:00 Localtime 2006
WH040000350:admin>
コマンドパラメータ:
date “mmddhhmmyy”
パラメータ :mm = 月
dd = 日
hh = 時間
00-12
00-31
00-23
00-59
mm = 分
yy = 西暦下2桁 00-99
<タイムサーバー設定>
1> コンソール画面上で“tsclockserver”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在のタイムサーバーの設定を確認します。
タイムサーバ設定確認>
WH040000350:admin> tsclockserver
LOCL
WH040000350:admin>
タイムサーバーが設定されていない場合“LOCL”が表示されます。
ヒント
3> コンソール画面上で“tsclockserver”コマンドを使用しタイムサーバーを設定します。
“tsclockserver xxx.xxx.xxx.xxx”を入力しタイムサーバーを設定します。
“xxx.xxx.xxx.xxx“は設定するタイムサーバーのIP Addressを入力します。
タイムサーバ設定>
WH040000350:admin> tsclockserver 192.168.1.1
Updating Clock Server configuration...done.
WH040000350:admin>
利用可能なタイムサーバーの IP Address に関してはシステム管理者にお問
い合わせ願います。
ヒント
- 98 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4> コンソール画面上で“tsclockserver”を入力し設定後の確認をしてください。
タイムサーバー設定確認>
WH040000350:admin> tsclockserver
192.168.1.1
WH040000350:admin>
設定を実施したタイムサーバーのIP Addressが表示されます。
ヒント
<タイムサーバー設定削除>
1> コンソール画面上で“tsclockserver”を入力してください。
スイッチコンソールで使用するコマンドは全て小文字で入力をお願いしま
す。
ヒント
2> 現在のタイムサーバーの設定を確認します。
タイムサーバー設定確認>
WH040000350:admin> tsclockserver
192.168.1.1
WH040000350:admin>
設定されているタイムサーバーのIP Addressが表示されます。
ヒント
3> コンソール画面上で“tsclockserver LOCL”を入力してください。
“LOCL”は大文字で入力してください。
重要
設定変更>
WH040000350:admin> tsclockserver LOCL
Updating Clock Server configuration...done.
WH040000350:admin>
4> コンソール画面上で“tsclockserver”を入力し“LOCL”が表示されることを確認してください。
設定変更>
WH040000350:admin> tsclockserver
LOCL
WH040000350:admin>
タイムサーバーの設定が削除された場合“LOCL”が表示されます。
ヒント
- 99 -
Download from Www.Somanuals.com. All Manuals Search And Download.
各種設定の保存/再設定
本製品の設定情報に関しては configupload/configdownload コマンドを利用することにより保存・
再設定が可能です。
本製品の設定を保存するコマンドを実施する場合別途FTPサーバーが必要となりま
す。作業実施前にFTPサーバーの準備をお願いします。
重要
configupload/configdownloadコマンドではスイッチ名、IPアドレスの情報は変更
されません。configdownload実施後に個別コマンドで設定変更してください。
装置設定の保存に関しては装置障害時における装置交換等のシステム復旧
ヒント
時に必要となります、新規装置設置時及び装置設定変更時に設定保存をお願
いします。
1) 設定ファイルのFTPサーバへの転送
“configupload”コマンドを使用し設定ファイルをFTPサーバに転送します。
“configupload ”コマンドの使用方法
configupload
← コマンド入力
← 転送方法
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]:
User Name [user]:
← FTPサーバIPアドレス
← FTPサーバユーザー名
← ファイル名
File Name [config.txt]:
Password:
← FTPサーバパスワード
※ [ ]内の表示はDefault設定値
2) 設定ファイルのスイッチへの転送
“configdownload”コマンドを使用し設定ファイルをスイッチに転送します。
“configdownload ”コマンドの使用方法
configdownload
← コマンド入力
← 転送方法
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]:
User Name [user]:
← FTPサーバIPアドレス
← FTPサーバユーザー名
← ファイル名
File Name [config.txt]:
Password:
*** CAUTION ***
← FTPサーバパスワード
This command is used to download a backed-up configuration
for a specific switch. If using a file from a different
switch, this file's configuration settings will override
any current switch settings. Downloading a configuration
file, which was uploaded from a different type of switch,
may cause this switch to fail. A switch reboot might be
required for some parameter changes to take effect.
Do you want to continue [y/n]:
※ [ ]内の表示はDefault設定値
← 転送実施の可否
- 100 -
Download from Www.Somanuals.com. All Manuals Search And Download.
<設定の保存>
1> 本製品がネットワークに接続されていることを確認してください。
設定情報の保存方法としてスイッチモジュール内の各種設定をテキストフ
ヒント
ァイルでFTPサーバーへ転送するためネットワークに接続する必要がありま
す。
2> FTPサーバーがアクセス可能であることを確認してください。
設定情報の保存方法としてスイッチモジュール内の各種設定をテキストフ
ァイルでFTPサーバーへ転送します。
ヒント
3> スイッチモジュールのコンソールにLoginします。
4> コンソール画面上で“configupload”を入力してください。
WH040000350:admin> configupload
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]: 192.168.1.90
User Name [user]: switch
File Name [config.txt]:
Password:
Upload complete
WH040000350:admin>
設定ファイルを転送する FTP サーバ IP アドレス及びユーザーID、パスワードに関
重要
する情報に関してはご利用になるFTPサーバーの管理者へお問い合わせ願います。
FTPサーバーのrootフォルダに設定ファイル“config.txt”が転送されます。
設定ファイルのファイル名を変更する場合、File Nameの項目で変更するフ
ァイル名を入力します。
ヒント
5> FTPサーバーのrootフォルダに“config.txt”またはconfiguploadコマンドで指定した名前のテキ
ストファイルが転送されていることを確認してください。
<設定内容の復元>
1> 本製品がネットワークに接続されていることを確認してください。
設定情報の復元方法としてFTPサーバーからスイッチモジュール内の各種設
ヒント
定をテキストファイルでスイッチモジュールへ転送するためネットワーク
に接続する必要があります。
2> FTPサーバーがアクセス可能であることを確認してください。
設定情報の復元方法としてFTPサーバーからスイッチモジュール内の各種設
定をテキストファイルでスイッチモジュールへ転送します。
ヒント
- 101 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3> スイッチモジュールのコンソールにLoginします。
4> コンソール画面上で“switchdisable”を入力してください。
システム運用中における設定ファイルの再設定は実施できません。
重要
本コマンドを実施することによりスイッチモジュールが無効状態となります。
5> コンソール画面上で“configdownload”を入力してください。
WH040000350:admin> configdownload
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]: 192.168.1.90
User Name [user]: switch
File Name [config.txt]:
Password:
*** CAUTION ***
This command is used to download a backed-up configuration
for a specific switch. If using a file from a different
switch, this file's configuration settings will override
any current switch settings.
Downloading a configuration
file, which was uploaded from a different type of switch,
may cause this switch to fail. A switch reboot might be
required for some parameter changes to take effect.
Do you want to continue [y/n]: y
fwConfigReload: Fabric Watch configuration reloaded.
download completed.
WH040000350:admin>
6> コンソール画面上で“switchenable”を入力してください。
本コマンドを実施することによりスイッチモジュールが有効状態となります。
重要
7> スイッチモジュールの設定を確認してください。
・Domain IDの確認
・ゾーニング設定の確認
・ポート設定の確認
・その他設定実施項目
8> コンソール画面上で“reboot”を入力してください。
configdownload で設定した一部の設定情報はスイッチリブート後に有効になりま
重要
す。装置設定を全て有効とするためスイッチのリブートを必ず実施してください。
9> スイッチが正常起動していることを確認してください。
- 102 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: Connecting Serial Port
The FC Switch Module includes the feature of logging in to the console of the FC Switch Module via a
serial port to provide setting for the FC Switch Module.
To use a serial console, the following jobs are previously required.
Connecting Serial Console
You should login to the serial console of the FC Switch Module from the console of the Enclosure
Manager (EM) card in the Blade Enclosure (SIGMABLADE). For the login from the console of the
EM card in the Blade Enclosure (SIGMABLADE), refer to the User’s Guides of the Blade Enclosure
(SIGMABLADE) and EM card.
The parameters required to connect to the serial port installed on the FC Switch Module should be
set as shown in the table below:
Transmission speed
Data length
Parity
9600 bps
8 bits
None
Stop bit
1 bit
Flow control
None
The user name and password for the initial login to the console on the FC Switch Module are as
follows:
Administrator authority: Display of FC Switch Module setting information and setting change
User name for FC Switch Module login:admin
Password for FC Switch Module login:password
User authority: Display of FC Switch Module setting information
User name for FC Switch Module login:user
Password for FC Switch Module login:password
Type the user names and passwords for FC Switch Module login with
lowercase letters.
For the serial login to the FC Switch Module from the EM card in a Blade
Enclosure (SIGMABLADE) through Ethernet, refer to the User's Guides of
the Blade Enclosure (SIGMABLADE) and EM card.
- 103 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: Checking Connections of Peripherals
To check the connections of the FC Switch Module with peripherals, you should login to the console of
the FC Switch Module.
Checking Linkup of Fibre Channel Devices
Entering the "switchshow" command on the console allows the current connections of the FC
Switch Module with fibre channel devices to be displayed.
Type "switchshow" on the console.
Sample screen displayed by "switchshow"
WH040000363:admin> switchshow
switchName:
switchType:
switchState:
switchMode:
switchRole:
switchDomain:
switchId:
switchWwn:
zoning:
switchBeacon:
WH040000363
43.1
Online
Native
Principal
1
fffc01
10:00:00:05:1e:02:04:09
OFF
OFF
Area Port Media Speed State
==============================
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
--
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
id
id
--
--
--
--
--
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
4G
No_Module (No POD License) Disable
Online
Online
Online
Online
Online
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
No_Sync
Online
F-Port 10:00:00:00:c9:51:fe:55
F-Port 10:00:00:00:c9:51:fg:99
F-Port 10:00:00:00:c9:51:fe:66
F-Port 10:00:00:00:c9:51:ff:28
F-Port 10:00:00:00:c9:51:fe:35
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
Disabled (Persistent)
F-Port 20:05:00:30:13:84:04:6c
F-Port 20:06:00:30:13:84:04:6c
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
23 23
Online
No_Module
No_Module
No_Module (No POD License) Disable
No_Module (No POD License) Disable
No_Module (No POD License) Disable
WH040000363:admin>
For N8406-019, internal ports 1 - 8 and external ports 17 - 20 are available.
Other ports are unavailable while their states are displayed.
For N8406-020, all internal and external ports are available.
Check that the linkup information on devices connected to FC Switch
Modules appears by using the "switchshow" command.
If the linkup information on a fibre channel device does not appear, the
device, SFP module or FC cable may be defected.
- 104 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Information displayed by "switchshow"
Description
Item
Displayed data
Port
Media
0 - 23
--
Cu
id
2G
4G
No_Module
Online
Correspond to the port numbers of the FC Switch Module.
No SFP module is installed on ports (for external ports only).
Media of copper type is installed. (The value is fixed for internal ports).
An SFP module of fibre type is installed.
The port data rate is fixed to 2G bps.
The port data rate is fixed to 4G bps.
No SFP module is installed.
The Fibre channel device is linked up normally.
Speed
State
Either of the following two messages appears in normal linkup status
depending on the port topology of the connected fibre channel device:
"Online F-Port WWN" in fabric connection or
"Online L-Port 1Pubric" in loop connection.
No_Sync
No_light
The SFP module receives optical signals but the fibre channel device is
not linked up normally.
The SFP module does not receive optical signals.
You can identify the fault location by comparing the information shown by
"switchshow" with the actual connection.
The state messages for the internal and external ports unavailable to
N8406-019 are "No_Sync Disabled (Persistent)" and "No_Module (No POD
License) Disable," respectively.
- 105 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Registration of Fibre Channel Devices in
Name Server
Entering the "nsshow" command on the console allows current fibre channel devices registered in
the name server for FC Switch Modules to be known.
Type "nsshow" on the console.
Sample screen displayed by "nsshow"
WH040000363:admin> nsshow
{
Type Pid
COS
PortName
NodeName
TTL(se
c)
N
N
010500;
FC4s: FCIP FCP
2,3;10:00:00:00:c9:51:fe:97;20:00:00:00:c9:51:fe:97; na
NodeSymb: [39] "Emulex LPe1105-NEC FV2.50A8 DV5-1.20A3 "
Fabric Port Name: 20:05:00:05:1e:02:04:09
Permanent Port Name: 10:00:00:00:c9:51:fe:97
011100;
FC4s: FCP [NEC
3;20:05:00:30:13:84:04:6c;20:00:00:30:13:84:04:6c; na
iStorage 1000 1400]
Fabric Port Name: 20:11:00:05:1e:02:04:09
Permanent Port Name: 20:05:00:30:13:84:04:6c
The Local Name Server has 2 entries }
WH040000363:admin>
Check that the "nsshow" command can show various information on fibre channel
devices linked up to FC Switch Modules.
If the information on a connected device does not appear, the device, SFP module or
FC cable may be defected.
For details of the displayed information, refer to the User’s Guides of the connected
fibre channel devices.
Information displayed by "nsshow"
Item
Display
Type
Indicates port status.
" N," "NL", and "U" mean N_Port, NL_Port and unknown status, respectively.
PID
Indicates the 24-bit ID of each fibre channel device.
Consists of a 6-digit value in the format of "xxyyzz" as follows:
xx: Domain ID of switch
yy: Port number (hexadecimal notation)
zz: Loop ID ("00" in fabric connection)
PortName
NodeName
Indicates the world wide port name (WWPn) of each connected fibre channel device.
Indicates the world wide node name (WWNn) of each connected fibre channel device.
"nsshow" allows you to know WWPn’s of fibre channel devices connected to FC Switch
Modules. WWPn’s can be used for various settings of peripherals.
Depending on the type of the OS you use, "PID" has some influence on the hardware
path of the logic with which the OS recognizes disk array units. Take sufficient note on
the PID if a job is done to change the PID after system operation is started.
Related jobs:
Change of domain ID and change of port topology of connected device
- 106 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: Cascade Connection
FC Switch Modules N8406-*** can be subjected to cascade connection with each other.
The following describes the cascade feature of the FC Switch Module.
Cascade Connection
The cascade feature of the FC Switch Module is characterized as follows:
The FC Switch Modules subjected to cascade connection can share the external devices connected
to them.
The FC Switch Modules subjected to cascade connection can share the CPU blade connected to
each of the FC Switch Modules.
Cascade connection of up to three hops is supported.
Zoning can be provided among FC Switch Modules subjected to cascade connection.
When a Fabric is constructed by cascading the FC Switch Modules, one of the FC Switch Modules
in the Fabric operates as a Principal switch. A single FC Switch Module without cascading always
operates a Principal switch.
All FC Switch Modules except the Principal switch operate as Subordinate switches.
Any FC Switch Module in the Fabric can be set to be a Principal switch by
“fabricprincipal” command.
Cascading path between FC Switch Modules can be connected by multiple
connections.
Influence to the Fabric when a single cascading path failure occurred can be
avoided by making cascading path redundant or routing path between FC
Switch Modules redundant.
The maximum transmission rate among FC Switch Modules subjected to
cascade connection is 4G bps per one cascade path.
Any cascade connections of more than three hops are not supported.
The FC Switch Module can make cascade connection with only
N8406-019/020. Cascade connection with any other FC switch is not supported.
The FC Switch Modules in the same Blade Enclosure (SIGMABLADE) cannot
make cascade connection with each other.
The role of the FC Switch Module (Principal or Subordinate) may be changed
by the Fabric reconstruction.
When cascade connection is made, a Fabric construction process is done in the
FC Switch Modules connected. Influence to I/O operation in the Fabric may
occur during the Fabric construction process (including reconstruction process).
A Fabric reconstruction process occurs if the Principal switch is removed from
the Fabric by the cascading path failure.
Even if the cascading path or routing path between FC Switch Modules is
redundant, A Fabric reconstruction occurs at other switches if the Principal
switch is removed from the Fabric when a failure occurs at the Principal switch.
When setting of Zoning is done in the FC Switch Modules with cascading
connection, the ports used for cascading path between FC Switch Modules
must not be set zone. The cascading path is used by all zones. It may become
a cause of failure of device recognition if setting of Zoning is done with the zone
including the ports used for cascading path.
- 107 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Provide cascade connection for FC Switch Modules according to the following procedure:
1. Check the locations of FC Switch Modules subjected to cascade connection and confirm that SFP
modules are installed on the ports for the connection.
Install SFP modules if not installed.
2. Check the internal settings of the additional FC Switch Modules to connect.
Zoning should not be set.
If set, always disable all zoning configurations to delete them completely.
After deleting the zone configurations, save the new zone configurations by using the "cfgSave"
command.
For how to delete zone information, see "Setting zoning" in "Appendix FC
Switch Module Setting Features".
If an additional introduced FC Switch Module is made cascade connection to
the FC Switch Modules in operation, delete the zone information only in the
additional FC Switch Module to connect.
If the Zone information of the FC Switch Module used in the system operated,
system failure or data destruction may occur. The Zone information of the FC
Switch Module in the system operated must not be deleted.
The Zone information set in the FC Switch Module operated is transmitted to
the FC Switch Module subjected to cascade connection and becomes
effective.
3. Disable FC Switch Modules to be connected by using the "switchDisable" command.
WH040000557:admin>
WH040000557:admin> switchdisable
WH040000557:admin>
4.
Change the domain IDs of FC Switch Modules to be connected.
For how to change domain IDs, see the domain ID setting feature in
"Appendix FC Switch Module Setting Features".
5. Connect FC Switch Modules with each other through an FC cable.
6. Make disabled FC Switch Modules effective by using the "switchEnable" command.
WH040000557:admin>
WH040000557:admin> switchenable
WH040000557:admin>
- 108 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. After making connected FC Switch Modules effective, execute the "switchShow" command for each
FC Switch Module to check connections among the FC Switch Modules.
WH040000557:admin>switchshow
↓ (Omitted)
15 15
16 16
17 17
18 18
19 19
20 20
cu
cu
id
id
--
id
4G
4G
4G
4G
4G
4G
No_Sync
No_Sync
No_Light
No_Light
No_Module
Online
Disabled (Persistent)
Disabled (Persistent)
E-Port 10:00:00:05:1e:03:55:f9 "WH040000642" (upstre
am)
21 21
22 22
23 23
--
--
--
4G
4G
4G
No_Module
No_Module
No_Module
WH040000557:admin>
If the cascade path can be linked normally, the status message on each
connected port is either of the following ones:
E-Port WWN "Switch Name" (upstream)
E-Port WWN "Switch Name" (downstream)
If more than one cascade path are connected between specific FC Switch
Modules, "(upstream)" and "(downstream)" do not appear for the second and
following cascade paths.
If a status message other than above appears, a malfunction is detected in
the cascade connection. Retry the job from the beginning.
Sample display: Domain ID overlap
Online E-Port segmented,(domain overlap)
Before cascade connection can be provided for FC Switch Modules, the
zoning setting of the FC Switch Modules should always be deleted. Cascade
connection under zoning status may cause an error to occur.
Any FC Switch Modules with a duplicate domain ID cannot be subjected to
cascade connection. Always change the domain IDs of FC Switch Modules
subjected to cascade connection to be unique.
The data transmission speed between FC Switch Modules subjected to
cascade connection is 4G bps per path.
For cascade connection, first check the upper limit of the data transmission
speed between FC Switch Modules.
8. When more than two FC Switch Modules are made cascade connection, execute “fabricshow”
command to check status of the cascade connections between the FC Switch Modules.
WH040001124:admin> fabricshow
Switch ID Worldwide Name
Enet IP Addr
FC IP Addr
Name
-------------------------------------------------------------------------
1: fffc01 10:00:00:05:1e:03:55:d8 192.168.1.32
2: fffc01 10:00:00:05:1e:03:43:25 192.168.1.33
3: fffc03 10:00:00:05:1e:03:32:3a 192.168.1.34
0.0.0.0
0.0.0.0
0.0.0.0
" WH040001100"
" WH040001945"
>"WH040001124"
The Fabric has 3 switches
WH040001124:admin>
If the FC Switch Modules are properly made cascade connection, information
of Domain ID, WWN, IP Address and Switch Name of each FC Switch Module
connected are displayed (FC IP is not used in the FC Switch Module).
- 109 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample cascade connection
Setting Principal switch only for the FC Switch Module in Blade Enclosure
(SIGMABLADE) must be done. For how to set Principal switch, see "Checking
/ Setting Principal Selection Mode" in "Appendix FC Switch Module Setting
Features".
Cascading two FC Switch Modules (Blade Enclosure)
1. One path configuration between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
If a failure occurs on the cascading path between the FC Switch Modules, a
Fabric reconstruction occurs. Influence to I/O operations may occur not only
between the cascading FC Switch Modules but within each FC Switch Module
(each Blade Enclosure).
2. Two paths configuration between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
By making cascade connection between FC Switch Modules to two paths,
even if a failure occurs on one cascade path, no influence to I/O operation
occur because I/O operation is succeeded by redundant path and no Fabric
reconstruction occurs.
- 110 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Cascading three FC Switch Modules (Blade Enclosure)
1. Configuration with minimum number of cascading paths
Blade Enclosure #1
Blade Enclosure #2
Blade Enclosure #3
If a failure occurs on the cascading path between the FC Switch Modules, a
Fabric reconstruction occurs. Influence to I/O operations may occur not only
between the cascading FC Switch Modules but within each FC Switch Module
(each Blade Enclosure).
2. Two paths configuration between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
Blade Enclosure #3
By making cascade connection between FC Switch Modules to two paths,
even if a failure occurs on one cascade path, no influence to I/O operation
occur because I/O operation is succeeded by redundant path and no Fabric
reconstruction occurs.
- 111 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Alternate path between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
Blade Enclosure #3
By making cascade connection among all three FC Switch Modules, even if a
failure occurs on one cascade path, no influence to I/O operation occur
because communication between FC Switch Modules can be succeeded by
the alternate path and no Fabric reconstruction occur.
Cascading four FC Switch Modules (Blade Enclosure)
1. Configuration with minimum number of cascading paths
Blade Enclosure #1
Blade Enclosure #4
Blade Enclosure #2
Blade Enclosure #3
If a failure occurs on the cascading path between the FC Switch Modules, a
Fabric reconstruction occurs. Influence to I/O operations may occur not only
between the cascading FC Switch Modules but within each FC Switch Module
(each Blade Enclosure).
- 112 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Two paths configuration between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
Blade Enclosure #3
Blade Enclosure #4
By making cascade connection between FC Switch Modules to two paths,
even if a failure occurs on one cascade path, no influence to I/O operation
occur because I/O operation is succeeded by redundant path and no Fabric
reconstruction occurs.
3. Alternate path between the FC Switch Modules
Blade Enclosure #1
Blade Enclosure #2
Blade Enclosure #3
Blade Enclosure #4
By making cascade connection among all four FC Switch Modules, even if a
failure occurs on one cascade path, no influence to I/O operation occur
because communication between FC Switch Modules can be succeeded by
the alternate path and no Fabric reconstruction occur.
- 113 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: FC Switch Module Setting Features
To use FC Switch Modules, you should login to the console to provide proper setting for the FC Switch
Modules. The appendix describes the settings required to use the FC Switch Modules.
Set the internal features of the FC Switch Module after reading this guide
carefully to be familiar with the features.
Some setting change for the FC Switch Module may have bad influences on
the system being operated. Examine changing information sufficiently before
setting change.
Changing Password
After completing login to the console of the FC Switch Module, change the password of the FC Switch
Module according to the procedure below. (You may or may not change the password.)
1. Type "passwd" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. Messages such as those shown below appear. According to the messages, enter the old and new
passwords. Reenter the new password.
WH040000363:admin> passwd
Changing password for admin
Enter old password:
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Saving password to stable storage.
Password saved to stable storage successfully.
WH040000363:admin>
The new password is made effective at the next login.
The password should consist of 8 - 40 alphanumeric characters.
Be careful not to forget the new password. If you forget, proper maintenance
is required. Contact your service representative.
- 114 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Network Setting
After completing login to the console of the FC Switch Module, change the network setting of the
FC Switch Module according to the procedure below. (The network setting is always required.)
Installing more than one FC Switch Module in a specific Blade Enclosure
(SIGMABLADE) without network setting may cause an unintentional error to
occur due to a duplicate IP address. Always set the IP address of each FC
Switch Module uniquely.
Setting at shipment from factory
The network setting is provided for an FC Switch Module as follows when it is shipped from the
factory.
Ethernet IP Address
0.0.0.0
Ethernet Subnet Mask
Fibre Channel IP Address
Fibre Channel Subnetmask
Gateway Address
255.255.255.0
0.0.0.0
0.0.0.0
0.0.0.0
After proper network setting enabling connection to a network, you can login
to the console of FC Switch Modules via the network.
1. Type "ipaddrset" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The following entry screen appears which asks you to enter the network information in the area
from the Ethernet IP address to the gateway IP addresses. Type setting values and press the
[Enter] key.
Contact your network administrator for details of the setting values.
HW060000955:admin> ipaddrset
Ethernet IP Address [0.0.0.0]:192.168.1.15
Ethernet Subnetmask [255.255.0.0]:255.255.255.0
Fibre Channel IP Address [0.0.0.0]:
Fibre Channel Subnetmask [0.0.0.0]:
Gateway IP Address [0.0.0.0]:192.168.1.254
Issuing gratituous arp...Done.
IP address is being changed...Done.
Committing configuration...Done.
HW060000955:admin>
IP addresses set for FC Switch Modules should be located on the same
subnet for the IP address of the Blade Enclosure (SIGMABLADE) in which
the FC Switch Modules are installed.
After the network setting is completed, the network-related daemon program
in the firmware of the FC Switch Module automatically restarts. The network
setting is made effective just after the auto restart of the daemon program.
To access to an FC Switch Module via the network, some settings may be
required for the Blade Enclosure (SIGMABLADE). For the settings, refer to
the User’s Guide of the Blade Enclosure (SIGMABLADE).
Do not change "Fibre Channel IP Address" and "Fibre Channel
Subnetmask" because they are unavailable.
If some network setting is changed during system operation, an error
message may appear on a log of the host connected to the FC Switch
Module at restart of the network-related daemon program.
- 115 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Type "ipaddrshow" on the console screen.
The network setting appears. Check the setting.
WH040000363:admin> ipaddrshow
SWITCH
Ethernet IP Address: 192.168.1.15
Ethernet Subnetmask: 255.255.255.0
Fibre Channel IP Address: 0.0.0.0
Fibre Channel Subnetmask: 0.0.0.0
Gateway Address: 192.168.1.254
WH040000363:admin>
If one or more errors are found in the setting, reset the data appropriately.
- 116 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Switch Names
After completing login to the console of FC Switch Modules, change the names of the FC Switch
Modules according to the procedure below. (The names may or may not be changed.)
A switch name can consist of up to 15 alphanumeric characters.
Change the names of FC Switch Modules in their initial installations. Some
setting change during system operation may have unintentional influences
on the system.
The names of FC Switch Modules appear at the prompt in the console
screen.
Up to four FC Switch Modules can be installed in a single Blade Enclosure
(SIGMABLADE).
The new names of FC Switch Modules resulting from changes can be used
to identify the FC Switch Module on each slot in login to the console for
several settings.
Setting at shipment from factory
The switch name of an FC Switch Module is set to the product management number when the FC
Switch Module is shipped from the factory.
1. Type "switchname" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The switch name set now appears.
WH040000363:admin> switchname
WH040000363
WH040000363:admin>
3. On the console screen, change the switch name by using the "switchname" command.
Type "switchname name" to change the switch name.
"name" should be the switch name to be set newly.
WH040000363:admin> switchname slot1
slot1:admin>
After the switch name of the FC Switch Module is changed, the new switch
name appears at the console prompt.
4. Run the "switchname" command on the console screen to confirm that the switch name specified
on step 3 appears.
- 117 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Port Data Rate
After completing login to the console of the FC Switch Module, change the port data rate of each
port on the FC Switch Module according to the procedure below. (The setting is always required.)
Setting at shipment from factory
The port data rate is fixed to 4G bps for every port when an FC Switch Module is shipped from the f
actory.
The port data rate of an FC Switch Module must be set to be the same as
that of fibre channel devices connected to the FC Switch Module. If the port
data rates are different, the connected fibre channel devices cannot link up
to the FC Switch Module. For the port data rate of each fibre channel device
to be connected to the FC Switch Module, refer to the User’s Guide of the
fibre channel device.
1. Type "portcfgshow" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The current port settings appear.
WH040000350:admin> portcfgshow
Ports of Slot 0
------------------+--+--+--+--+----+--+--+--+----+--+--+--+----+--+--+--
0 1 2 3
4 5 6 7
8 9 10 11 12 13 14 15
Speed
Trunk Port
4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G
ON .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable .. .. ON ON .. ON ON ON ON ON ON ON ON ON ON ON
Ports of Slot 0 16 17 18 19 20 21 22 23
------------------+--+--+--+--+----+--+--+--
Speed
Trunk Port
4G 4G 4G 4G 4G 4G 4G 4G
.. ON ON ON ON ON ON ON
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. ON ON ON ON .. .. ..
ON .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable ON .. .. .. .. .. .. ..
where AN:AutoNegotiate, ..:OFF, ??:INVALID.
WH040000350:admin>
The port status display also includes the information on the ports
unavailable to N8406-019. However, this is not an error.
- 118 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The port data rate can be changed in the following two ways.
Select either of the ways depending on the use of the FC Switch Module.
Changing the rates of all ports at a time
Type "switchcfgspeed x" to change the port data rate.
Value "x" is a new port data rate.
4 for 4G bps or 2 for 2G bps
WH040000350:admin> switchcfgSpeed 4
WH040000350:admin>
The port data rates of all external and internal ports of an FC Switch
Module can be changed at a time.
Changing data rates in ports
Type "portcfgspeed x y" to change the data rate of a specific port.
Value "x" is the number of the port whose data rate is to be changed.
N8406-019: internal ports 1 - 8 / external ports 17 - 20
N8406-020: internal ports 1 - 16 / external ports 17 - 23 and 0
Value "y" is a new port data rate.
4 for 4G bps or 2 for 2G bps
WH040000350:admin> portcfgspeed 17 2
WH040000350:admin>
The information on each port on the FC Switch Module can be
changed individually.
4. After the settings are changed completely, type "portcfgshow".
Make sure that the new data is reflected on the screen display. The processing is completed if the
data rate of each port is changed to the new data.
- 119 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Port Topology
After completing login to the console of the FC Switch Module, change the topology of external
ports on the FC Switch Module according to the procedure below. (The port topology must always
be set.)
Setting at shipment from factory
The port topology (Locked G_Port) is set as follows when an FC Switch Module is shipped from the
factory.
External ports:
Internal ports:
ON (Valid: only fabric devices connectable)
·· (Invalid: Select Auto as the topology.)
The port topology of an FC Switch Module must be set to be the same as
the port topology of fibre channel devices connected to the FC Switch
Module. If the port topologies are different, the connected fibre channel
devices cannot link up to the FC Switch Module. For the port topology of
each fibre channel device to be connected to an FC Switch Module, refer to
the User’s Guide of the fibre channel device.
1. Type "portcfgshow" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The current port settings appear.
WH040000350:admin> portcfgshow
Ports of Slot 0 0 1 2 3
------------------+--+--+--+--+----+--+--+--+----+--+--+--+----+--+--+--
4 5 6 7
8 9 10 11 12 13 14 15
Speed
Trunk Port
4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G
ON .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable .. .. ON ON .. ON ON ON ON ON ON ON ON ON ON ON
Ports of Slot 0 16 17 18 19 20 21 22 23
------------------+--+--+--+--+----+--+--+--
Speed
Trunk Port
4G 4G 4G 4G 4G 4G 4G 4G
.. ON ON ON ON ON ON ON
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. ON ON ON ON .. .. ..
ON .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. .. .. ..
Long Distance
VC Link Init
Locked L_Port
Locked G_Port
Disabled E_Port
ISL R_RDY Mode
RSCN Suppressed
Persistent Disable ON .. .. .. .. .. .. ..
where AN:AutoNegotiate, ..:OFF, ??:INVALID.
WH040000350:admin>
The port status display also includes the information on the ports
unavailable to N8406-019. However, this is not an error.
- 120 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Change the port topologies.
Change of port topology in ports
Type "portcfggport x y" to change the topology of a port.
Value "x" is the number of the port whose topology is to be changed.
External ports available to N8406-019: 17 - 20
External ports available to N8406-020: 17 - 23 and 0
Value "y" shows whether fixing the port topology to be set is enabled or disabled.
0 = Disable or 1 = Enable
WH040000350:admin> portcfggport 17 1
WH040000350:admin>
The topology of a specific port in an FC Switch Module can be changed
individually.
The topologies of internal ports cannot be fixed.
Any port for which the setting is made enabled cannot accept the connection
of a loop device.
Always specify "Enable" if devices are connected with which port mode is
fabric (point-to-point). If "disable" is selected, some connected devices may
not be recognized.
When cascading connection is made between the FC Switch Modules, the
ports used for cascading path must be set “Enabled”.
4. After the setting is changed completely, type "portcfgshow".
Check if the new setting resulting from the change is made effective. The setting is completed if the
information on each changed port appears as shown below.
Information on Lockd G_Port
Changing to G_Port fixing
Releasing G_Port fixing
ON
··
- 121 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Domain ID
After completing login to the console of the FC Switch Module, change the domain ID of the FC
Switch Module according to the procedure below.
The setting may or may not be changed in no cascade connection. The
setting must be changed in cascade connection.
Setting at shipment from factory
The domain ID is set to 1 when an FC Switch Module is shipped from the factory.
Change the domain ID when the FC Switch Module is installed.
Changing the domain ID after starting the operation may cause a
system fault to occur.
1. Type "switchdisable" on the console screen to disable the FC Switch Module.
HW060000955:admin> switchdisable
Disabling the FC Switch Module makes it impossible for the FC Switch
Module to communicate with all fibre channel devices connected to it.
2. Type "configure" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
3. Type "configure" to display the setting input feature of the FC Switch Module.
Message "Fabric parameters (yes, y, no, n):" appears to ask whether the setting is already provided
or not. Type "y."
HW060000955:admin> configure
Configure...
Fabric parameters (yes, y, no, n): [no] y
4. On the menu for setting fabric parameters, enter a new value only for parameter "Domain ID" and
press [Enter] for other parameters.
Example of setting change> 1(def) → 2
Fabric parameters (yes, y, no, n): [no] y
Domain: (1..239) [1] 2
R_A_TOV: (4000..120000) [10000]
E_D_TOV: (1000..5000) [2000]
WAN_TOV: (0..30000) [0]
MAX_HOPS: (7..19) [7]
Data field size: (256..2112) [2112]
Sequence Level Switching: (0..1) [0]
Disable Device Probing: (0..1) [0]
Suppress Class F Traffic: (0..1) [0]
Switch PID Format: (1..2) [1]
Per-frame Route Priority: (0..1) [0]
Long Distance Fabric: (0..1) [0]
BB credit: (1..27) [16]
- 122 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. After the settings of fabric parameters are changed completely, type "n" or press [Enter] for any
message following "Insistent Domain ID Mode" asking whether setting is done or not.
Insistent Domain ID Mode (yes, y, no, n): [no]
Virtual Channel parameters (yes, y, no, n): [no]
F-Port login parameters (yes, y, no, n): [no]
Zoning Operation parameters (yes, y, no, n): [no]
RSCN Transmission Mode (yes, y, no, n): [no]
Arbitrated Loop parameters (yes, y, no, n): [no]
System services (yes, y, no, n): [no]
Portlog events enable (yes, y, no, n): [no]
ssl attributes (yes, y, no, n): [no]
http attributes (yes, y, no, n): [no]
snmp attributes (yes, y, no, n): [no]
rpcd attributes (yes, y, no, n): [no]
cfgload attributes (yes, y, no, n): [no]
webtools attributes (yes, y, no, n): [no] WARNING: The domain ID will ·······
HW060000955:admin>
6. To make the features of the FC Switch Module effective, type "switchenable".
HW060000955:admin> switchenable
- 123 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking / Setting Principal Selection Mode
After completing login to the console of the FC Switch Module, check and set Principal
Selection Mode of the FC Switch Module according to the procedure below.
The Setting is not necessary for a single use of the FC Switch Module.
Setting at shipment from factory
The Principal Selection Mode is set to “Disable” when an FC Switch Module is shipped from the
factory.
Change the Principal Selection Mode when the FC Switch Module is
installed. Changing the Principal Selection Mode after starting the
operation may cause disruption to the I/O operation.
Typ Checking current status
1. Type " fabricprincipal " on the console screen to display current setting status.
Any commands used on the switch console should be specified with
lowercase letters.
WH040001124:admin> fabricprincipal
Check Principal Selection Mode of all FC Switch Modules subjected to
cascade connection.
2. The message below is displayed on the console screen.
If Principal Selection Mode is set “Disable”.
WH040001124:admin> fabricprincipal
Principal Selection Mode: Disable
WH040001124:admin>
If Principal Selection Mode is set “Enable”.
The message displayed is different by the current status of the FC Switch
Module that the command is executed.
If the FC Switch Module is operating as a Principal switch.
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable (Switch currently principal)
WH040001124:admin>
If the FC Switch Module is operating as a Subordinate switch.
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable
WH040001124:admin>
- 124 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the setting
3. Login to the console of the FC Switch Module to change the setting.
Changing the Principal Selection Mode can be performed only on the FC
Switch Module logged in.
4. Type " fabricprincipal –f 1" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
Type “fabricprincipal” command with option “-f” and “1”, then the Principal
Selection Mode of the FC Switch Module that the command is executed is
changed to “Enable” and a Fabric reconstruction to change the FC Switch
Module to the Principal switch is performed.
The number of the FC Switch Module to set Principal Selection Mode “Enable”
in the Fabric must be only one.
WH040001124:admin> fabricprincipal -f 1
Principal Selection Mode enabled (Forcing fabric rebuild)
WH040001124:admin>
5. Type “fabricprincipal” on the console screen to check that the Principal Selection Mode is “Enable”.
WH040001124:admin> fabricprincipal
Principal Selection Mode: Enable (Switch currently principal)
WH040001124:admin>
If above message is not displayed as a result of the command, execute
“fabricprincipal –f 1” command again.
WH040001124:admin> fabricprincipal -f 1
Principal Selection Mode enabled (Forcing fabric rebuild)
WH040001124:admin>
6. Type “switchshow” on the console screen to check that the switchRole is displayed “Principal” in the
message of result.
WH040001124:admin> switchshow
switchName:
switchType:
switchState: Online
WH040001124
43.2
switchMode:
switchRole:
Native
Principal
switchDomain: 3 (unconfirmed)
switchId:
switchWwn:
zoning:
fffc03
10:00:00:05:1e:03:32:3a
OFF
switchBeacon: OFF
(Omitted)
- 125 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Zoning
After completing login to the console of the FC Switch Module, provide proper setting for the zoning
of the FC Switch Module according to the procedure below.
The FC Switch Module has two zoning features, or WWN mode zoning and port mode zoning.
NEC intensely recommends that the port mode zoning is used. If the WWN
mode zoning is used, zoning must be changed every replacement of a fibre
channel device in such cases as maintenance replacement of connected
devices. The port mode zoning does not require zoning resetting in
maintenance replacement (as long as port numbers are not changed).
Before changing zoning, you should be fully familiar with the zoning feature.
Some zoning change during system operation may cause a system fault to
occur unintentionally. While zoning is changed, check the changing
information and procedure and the influences of the change on others
sufficiently.
Disconnecting devices connected to the FC Switch Module logically by
zoning allows internal influences on fibre channels including login/logout of
devices out of the relevant zone to be rejected.
The command input on the console of the FC Switch Module does not
correspond to the file input feature of a communication terminal (VT100
emulator). Using file input of a communication terminal (VT100 emulator)
may cause a device error to occur. Note that the file input may not be used.
When setting of Zoning is done in the FC Switch Modules with cascading
connection, the ports used for cascading path between FC Switch Modules
must not be set zone. The cascading path is used by all zones. It may
become a cause of failure of device recognition if setting of Zoning is done
with the zone including the ports used for cascading path.
Setting at shipment from factory
Any zoning is not set when an FC Switch Module is shipped from the factory.
Every connected device can communicate with any other devices.
Flow of setting zoning
Checking current zoning (See page 128.)
Creating zone alias name (See page 129.)
Creating zone (See page 130.)
Creating configuration (See page 133.)
Enabling Configuration (See page 134.)
Other Settings
Modifying or deleting zone alias information (See page 136.)
Modifying or deleting zone (See page 137.)
Modifying or deleting configuration file (See page 138.)
Saving/Disabling configuration (See page 139.)
Miscellaneous (See page 140.)
- 126 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands Associated with Zoning
Item
Command
Description
Creating zone
aliases
Alicreate
Aliadd
Alidelete
Aliremove
Alishow
Zonecreate
Zoneadd
Zoneremove
Creates zone aliases including specified ports and WWPn’s.
Registers a port or WWPn to specified zone alias additionally.
Deletes specified port or WWPn from specified zone alias.
Removes specified port or WWPn from specified zone alias.
Displays zone alias information already registered.
Creates a zone including specified ports and WWPn’s.
Registers a port, zone alias name or WWPn additionally.
Deletes a port, zone alias name or WWPn from specified zone.
Creating zone
Zonedelete
Zoneshow
Deletes specified zone.
Shows zone information.
Creating
configuration file
Cfgcreate
Cfgdelete
Cfgclear
Creates zone configuration including specified zone.
Deletes specified zone configuration.
Deletes all information associated with zoning in FC Switch
Module.
Cfgadd
Adds specified zone to specified zone configuration.
Deletes specified zone from specified zone configuration.
Enables specified zone configuration.
Disables zone configuration enabled.
Shows configuration information.
Cfgremove
Cfgenable
Cfgdisable
Cfgshow
Operating
configuration
Cfgactvshow
Shows the information on zone configuration enabled only.
Cfgsave
Saves new configuration resulting from change.
Miscellaneous
zoneobjectrename
Allows created zone, zone configuration and zone alias names
already created to be changed.
zoneobjectexpunge
Zoneobjectcopy
Expunges specified zone, zone configuration and/or zone alias
name.
Copies specified zone, zone configuration and/or zone alias
information.
Commands associated with zoning require some arguments. See the
description on each command for details of how to use the command.
Failure in zoning may cause a system fault to occur. Before the zoning can
be provided, you must be fully familiar with the influences of related
commands on the system.
- 127 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Current Zoning
1. Type "cfgshow" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The current zoning information appears.
Without zoning information, skip to "Creating zone alias name" and following.
With some zoning information, recheck setting change to take proper action.
<No existence of zoning information>
HW060000955:admin> cfgshow
Defined configuration:
Effective configuration:
Effective configuration:
no configuration in effect
HW060000955:admin>
<Existence of zoning information>
HW060000955:admin> cfgshow
Defined configuration:
cfg: zone_cfg
zone1; zone2
1,0; 1,1
1,4; 1,5
zone: zone1
zone: zone2
Effective configuration:
cfg: zone_cfg
zone: zone1
1,0
1,1
1,4
1,5
zone: zone2
If enabled zoning information appears, take note on change of zoning
information. Zoning information is actually changed when configuration is
enabled after the change. Some setting errors before and/or after zoning
change may cause a system fault to occur.
- 128 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating Zone Alias Name
The information on fibre channel devices connected to an FC Switch Module can be changed to any
names.
A single zone alias name can include WWPn’s of fibre channel devices and port numbers (including
domain IDs) of FC Switch Modules.
Use the "alicreate" command to create a zone alias.
Format of "alicreate" command
alicreate "aliName" , "member;member"
(1)
(2)
(1) aliName:
Specify the alias name of a zone to be created with it enclosed with double quotation marks (").
(2) member:
Specify members to be included in the zone alias name with them delimited by commas (,). A
member can consist of a port number and a WWPn.
Delimit aliName and the first member with a comma (,).
Delimit adjacent members with a semicolon (;).
3. Create zone aliases by using the "alicreate" command on the console screen.
HW060000955:admin> alicreate "ali1","1,0;1,1"
HW060000955:admin> alicreate
"ali2","10:00:00:00:c9:4b:a1:e5;20:01:00:30:13:84:03:d2"
HW060000955:admin>
Zone alias information can include both port numbers (including domain IDs)
and WWPn’s concurrently.
Any commands used on the switch console should be specified with
lowercase letters.
Created zone aliases can be used as members when a zone is created.
- 129 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating Zone
Port mode zoning
For port mode zoning, use the domain ID and port number of the FC Switch Module to set zoning.
1) Checking domain ID
1. Type "switchshow" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The information on the status of FC Switch Modules appears.
See values of "switchDomain" for the domain ID (the value is set to 1 at shipment).
WH040000350:admin> switchshow
switchName:
switchType:
switchState:
switchMode:
switchRole:
switchDomain:
switchId:
WH040000350
43.1
Online
Native
Principal
1
fffc01
switchWwn:
zoning:
switchBeacon:
10:00:00:05:1e:02:08:53
OFF
OFF
Area Port Media Speed State
==============================
0 0 --
1 1 cu
2 2 cu
3 3 cu
4 4 cu
5 5 cu
6 6 cu
7 7 cu
8 8 cu
9 9 cu
10 10 cu
11 11 cu
12 12 cu
13 13 cu
14 14 cu
15 15 cu
16 16 cu
17 17 id
18 18 id
19 19 id
20 20 id
21 21 --
22 22 --
23 23 --
4G No_Module (No POD License) Disabled
4G No_Sync
4G No_Sync Disabled (Persistent)
4G No_Sync Disabled (Persistent)
4G Online
F-Port 10:00:00:00:c9:51:fe:c0
4G No_Sync Disabled (Persistent)
4G No_Sync Disabled (Persistent)
4G No_Sync Disabled (Persistent)
4G No_Sync Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G No_Sync (No POD License) Disabled (Persistent)
4G Online
4G Online
4G Online
4G Online
F-Port 20:01:00:30:13:84:09:42
F-Port 20:02:00:30:13:84:09:42
F-Port 20:05:00:30:13:84:09:42
F-Port 20:06:00:30:13:84:09:42
4G No_Module (No POD License) Disabled
4G No_Module (No POD License) Disabled
4G No_Module (No POD License) Disabled
WH040000350:admin>
If the domain ID is changed after port mode zoning, the zoning for the new
domain ID must be set.
Check the value of "switchname" in "switchshow" to check that the FC
Switch Module is subject to zoning.
- 130 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Creating zone
Use the "zonecreate" command to create a zone.
Format of "zonecreate" command
zonecreate "zonename"
(1)
,
"member;member;member"
(2)
(1) zonename:
Specify a zone name with it enclosed by double quotation marks (").
(2) member:
Specify a domain ID and a port number (decimal) with them delimited by a comma (,).
Delimit the zone name and the first port with a comma (,).
Delimit adjacent port specifications with a semicolon (;).
A zone name can be up to 64 alphanumeric characters.
This command must be done by the number of zones to be created.
3. Use the "zonecreate" command on the console screen to create zones.
HW060000955:admin> zonecreate "zone1","1,0;1,1"
HW060000955:admin> zonecreate "zone2","1,2;1,3"
HW060000955:admin> zonecreate "zone3","1,4;1,5"
HW060000955:admin> zonecreate "zone4","1,6;1,7"
HW060000955:admin>
Any commands used on the switch console should be specified with
lowercase letters.
4. Type "zoneshow" on the console screen.
HW060000955:admin> zoneshow
Defined configuration:
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
no configuration in effect
HW060000955:admin>
Confirm that all created zones appear by using the "zonecreate" command.
After a zone name, ports contained in the zone appear. Confirm that the
specified ports appear normally.
- 131 -
Download from Www.Somanuals.com. All Manuals Search And Download.
WWN mode zoning
For WWN mode zoning, use WWPn’s of the fibre channel devices connected to the FC Switch
Module to set the zoning.
1) Checking WWPn
1. Check WWPn’s of the fibre channel devices to be used.
For how to check WWPn’s of fibre channel devices to be used, refer to the
User’s Guides attached to the devices.
2) Creating zone
Use the "zonecreate" command to create a zone.
Use of "zonecreate" command
zonecreate "zonename"
(1)
,
"member;member;member"
(2)
(1) zonename:
Specify the created zone name with it enclosed by double quotation marks (").
(2) member:
Specify WWPn of a fibre channel device.
Delimit the zone name and the first WWPn with a comma (,).
Delimit adjacent WWPn specifications with a semicolon (;).
2. Use the "zonecreate" command on the console screen to create zones.
HW060000955:admin> zonecreate
"zone1","10:00:00:00:c9:4b:a1:e5;20:01:00:30:13:84:03:d2"
HW060000955:admin> zonecreate
"zone2","10:00:00:00:c9:4b:a2:05;20:02:00:30:13:84:03:d2"
HW060000955:admin> zonecreate
"zone3","10:00:00:00:c9:4b:a1:f6;20:05:00:30:13:84:03:d2"
HW060000955:admin> zonecreate
"zone4","10:00:00:00:c9:4b:83:aa;20:06:00:30:13:84:03:d2"
HW060000955:admin>
Any commands used on the switch console should be specified with
lowercase letters.
A zone name can be up to 64 alphanumeric characters.
This command must be done by the number of zones to be created.
3. Type "zoneshow" on the console screen.
HW060000955:admin> zoneshow
Defined configuration:
zone: zone1 10:00:00:00:c9:4b:a1:e5; 20:01:00:30:13:84:03:d2
zone: zone2 10:00:00:00:c9:4b:a2:05; 20:02:00:30:13:84:03:d2
zone: zone3 10:00:00:00:c9:4b:a1:f6; 20:05:00:30:13:84:03:d2
zone: zone4 10:00:00:00:c9:4b:83:aa; 20:06:00:30:13:84:03:d2
Effective configuration:
no configuration in effect
HW060000955:admin>
Confirm that all created zones appear by using the "zonecreate" command.
After a zone name, WWPn’s contained in the zone appear. Confirm that the
specified WWPn’s appear normally.
- 132 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating Configuration
Before zoning can be set, proper configuration including zones created previously must be
generated. More than one configuration can be created.
1) Creating configuration
Use the "cfgcreate" command to create a configuration file.
Use of "cfgcreate" command
cfgcreate
"cfgName"
(1)
,
"member;member;member"
(2)
(1) cfgName:
Specify the name of a zone configuration to be created with it enclosed by double quotation
marks (").
(2) member:
Specify a zone name already created with it enclosed by double quotation marks (").
Delimit the configuration name and the first zone name with a comma (,).
Delimit adjacent zone names with a semicolon (;).
1. Type "zoneshow" on the console screen.
HW060000955:admin> zoneshow
Defined configuration:
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
no configuration in effect
HW060000955:admin>
Confirm that all required zones are created.
Create one or more zones if necessary.
2. Use the "cfgcreate" command to create configuration.
HW060000955:admin>
HW060000955:admin> cfgcreate "cfg1","zone1;zone2;zone3;zone4"
HW060000955:admin>
If a zone name not registered in the zone information is specified, the
command causes an error to occur. The configuration is not created
normally. Always specify zone names already created.
- 133 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Enabling Configuration
Enable created configuration. Only a single configuration can be enabled at a time.
1) Validating configuration
Use the "cfgenable" command to enable a configuration.
Format of "cfgenable" command
cfgenable
"cfgName"
(1)
(1) cfgName:
Specify a zone configuration name with it enclosed by double quotation marks (").
If you try to enable configuration by using the "cfgenable" command, the
message asking whether the configuration is enabled appears. Type "y" if
the configuration is enabled. Type "n" if not.
Message sample:
Do you want to enable 'cfg1' configuration (yes, y, no, n): [no]
1. Type "cfgshow" on the console screen.
HW060000955:admin> cfgshow
Defined configuration:
cfg: cfg1
zone1; zone2; zone3; zone4
zone: zone1 1,0;1,1
zone: zone2 1,2;1,3
zone: zone3 1,4;1,5
zone: zone4 1,6;1,7
Effective configuration:
Effective configuration:
no configuration in effect
HW060000955:admin>
Confirm that the configuration to be enabled appears in "Defined
Configuration".
Create configuration if necessary.
2. Use the "cfgenable" command to enable the configuration.
HW040000955:admin> cfgenable "cfg1"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'cfg1' configuration (yes, y, no, n): [no] y
zone config "cfg1" is in effect
Updating flash ...
HW040000955:admin>
If a configuration name not registered in the zone information is specified,
the command causes an error to occur without the configuration enabled.
Always specify a configuration name created already.
- 134 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Use the "cfgactvshow" command to confirm that the configuration is enabled.
Enabled configuration names, enabled zone names and the information on ports and WWPn’s and
zone alias names contained in zones appear below "Effective Configuration."
HW060000955:admin> cfgactvshow
Effective configuration:
cfg: cfg1
zone: zone1 1,0
1,1
zone: zone2 1,2
1,3
zone: zone3 1,4
1,5
zone: zone4 1,6
1,7
If enabled zoning information includes one or more setting errors, disable
the configuration and correct the zoning information.
- 135 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying or Deleting Zone Alias Information
The following describes modification or deletion of created zone alias information.
After modification by using a relevant command, confirm that the
modification is done normally by using the "alishow" command.
1. Register additional information to a zone alias.
Use the "aliadd" command.
Using the "aliadd" command allows additional information (including port information and WWPn) to
be registered in the specified zone alias additionally.
aliadd
"aliname" , "member" <enter>
(1) (2)
(1) aliname:
Specify a zone alias name with it enclosed with double quotation marks (").
(2) member:
Specify a port and WWPn.
Delimit the zone name and the first additional information with a comma (,).
Delimit adjacent additional information with a semicolon (;).
2. Delete information from a zone alias.
Use the "aliremove" command.
Using the "aliremove" command allows registered information (including port information and
WWPn) specified from a zone alias specified to be deleted.
aliremove
"aliname" , "member" <enter>
(1) (2)
(1) aliname:
Specify a zone alias name with it enclosed with double quotation marks (").
(2) member:
Specify the port and WWPn to be deleted.
Delimit the zone name and additional information with a comma (,).
Delimit adjacent information to be deleted with a semicolon (;).
3. Delete a zone alias created already.
Use the "alidelete" command.
Using the "alidelete" command allows a zone alias registered already to be deleted.
alidelete
"aliname" <enter>
(1)
(1) aliname:
Specify a zone alias name with it enclosed with double quotation marks (").
- 136 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying or Deleting Zone
The following describes modification or deletion of a zone already created.
After modification by using a relevant command, confirm that the
modification is done normally by using the "zoneshow" command.
1. Add port information, WWPn and zone alias name to a zone.
Use the "zoneadd" command.
Using the "zoneadd" command allows additional information (including port information, WWPn and
zone alias name) to be added to a zone.
zoneadd "zonename" , "member" <enter>
(1)
(2)
(1) zonename:
Specify a zone name with it enclosed with double quotation marks (").
(2) member:
Specify port information, WWPn or zone alias.
Delimit the zone name and additional information with a comma (,).
Delimit adjacent additional information with a semicolon (;).
2. Delete port information, WWPn and/or zone alias name from a zone.
Use the "zoneremove" command.
Using the "zoneremove" command allows port information, WWPn and/or zone alias name to be
deleted from a zone.
zoneremove "zonename" , "member" <enter>
(1)
(2)
(1) zonename:
Specify a zone name with it enclosed with double quotation marks (").
(2) member:
Specify port information, WWPn or zone alias.
Delimit the zone name and additional information with a comma (,).
Delimit adjacent information to be deleted with a semicolon (;).
3. Delete a zone created already.
Use the "zonedelete" command.
Using the "zonedelete" command allows a zone to be deleted.
zonedelete "zonename" <enter>
(1)
(1) zonemame:
Specify a zone name with it enclosed with double quotation marks (").
- 137 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifying or Deleting Configuration File
The following describes modification or deletion of configuration already created..
After modification by using a relevant command, confirm that the
modification is done normally by using the "zoneshow" command.
1. Add a zone to zone configuration
Use the "cfgadd" command.
Using the "cfgadd" command allows a zone to be added to zone configuration.
Format of "cfgadd" command
cfgadd
"cfgName" , "member" <enter>
(1) (2)
(1) cfgName:
Specify a zone configuration name with it enclosed with double quotation marks (").
(2) member:
Specify a zone name to be added with it enclosed with double quotation marks (").
2. Delete a zone from zone configuration
Use the "cfgremove" command.
Using the "cfgremove" command allows a zone to be deleted from zone configuration.
Format of "cfgremove" command
cfgremove "cfgName" , "member" <enter>
(1)
(2)
(1) cfgName:
Specify a zone configuration with it enclosed with double quotation marks (").
(2) member:
Specify the zone name to be deleted with it enclosed with double quotation marks (").
3. Delete a configuration file created already
Use the "cfgdelete" command.
Using the "cfgdelete" command allows specified zone configuration to be deleted.
Format of "cfgdelete" command
cfgdelete
"cfgName" <enter>
(1)
(1) cfgName:
Specify a zone configuration with it enclosed with double quotation marks (").
4. Delete all zoning information
Using the "cfgclear" command allows all zoning information to be deleted.
Using the "cfgclear" command allows zone configuration to be deleted.
Format of "cfgclear" command
cfgclear
<enter>
Before the "cfgclear" command can be executed, the zoning information
being enabled must be disabled by using the "cfgdisable" command. Zoning
information can be deleted by using the "cfgclear" command. However, the
zoning being enabled at execution of the "cfgclear" command is still effective
after the execution.
- 138 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving/Disabling Configuration
The following describes the method of saving configuration after modification or disabling the
configuration files being enabled.
1. Save configuration subjected to modification.
Use the "cfgsave" command.
Using the "cfgsave" command allows modified configuration to be saved.
Format of "cfgsave" command
cfgsave
<enter>
Executing the "cfgsave" command allows new information resulting from
modification at the execution to be saved.
If configurations are saved by this command, the configurations set after
system rebooting are enabled.
2. Disable configuration files being enabled.
Use the "cfgdisable" command.
Using the "cfgdisable" command allows enabled configuration files to be disabled.
Format of "cfgdisable" command
cfgdisable
<enter>
Executing the "cfgdisable" command allows all zone configurations enabled
at the execution to be disabled.
- 139 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous
The following describes the method of changing the names of several zone objects created or
expunging or copying objects.
After modification by using a relevant command, confirm that the
modification is done normally by using the "cfgshow" command.
After a command is executed, run the cfgsave command to register the new
settings resulting from the change to be registered.
1. Change the name of an object created already
Use the "zoneobjectrename" command.
Using the "zoneobjectrename" command allows a zone object name to be changed.
Format of "zoneobjectrename" command
zoneobjectrename "objectName" , "newName" <enter>
(1)
(2)
(1) objectName:
Specify an existing object name to be changed with it enclosed with double quotation marks (").
(2) newName:
Specify the object name after the modification with it enclosed with double quotation marks (").
2. Expunge an object.
Use the "zoneobjectexpunge" command.
Using the "zoneobjectexpunge" command allows a specified object to be expunged.
Format of "zoneobjectexpunge" command
zoneobjectexpunge "objectName" <enter>
(1)
(1) objectName:
Specify an existing object name to be expunged with it enclosed with double quotation marks
(").
3. Copy an object already created
Use the "zoneobjectcopy" command.
Using the "zoneobjectcopy" command allows a zone object to be copied.
Format of "zoneobjectcopy" command
zoneobjectcopy "objectName" , "newName" <enter>
(1)
(2)
(1) objectName:
Specify an existing object name to be copied with it enclosed with double quotation marks (").
(2) newName:
Specify the name of the copied object with it enclosed with double quotation marks (").
- 140 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Time and Time Server
After completing login to the console of the FC Switch Module, set the clock built in the FC Switch
Module according to the following procedure.
Previous setting of the time of the clock built in the FC Switch Module allows
the time to be compared with logs of other devices in review of an error
occurred. Set the time after being familiar with the setting.
If a time server is available in environment where FC Switch Modules are
used, using the time server is enabled. If a time server is used, provide
proper setting for the time server without time setting.
Setting Time
1. Type "date" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. The current internal time of the FC Switch Module appears.
<Example of UTC display>
HW060000955:admin> date
Wed Jun 27 13:07:46 UTC 2006
HW060000955:admin>
<Example of local time display>
HW040000955:admin> date
Wed Nov 27 22:07:46 Localtime 2006
HW040000955:admin>
3. When the time is indicated by UTC (Universal Time Coordinated), set the time difference from the
UTC by using the "tstimezone" command. When the time is indicated by the local time, go to step 4.
Type “tstimezone h” or “tstimezone h, m” to change time zone.
Value “h” is the number of hour difference from the UTC. Valid values are -12 through 12.
Value “m” is the number of minute difference from the hour offset “h”. This value is an option and
valid values are -30, 0, or 30.
If the time difference from the UTC is "-3.5" hours.
HW060000955:admin> tstimezone -3, -30
Updating Time Zone configuration...done.
System Time Zone change will take effect at next reboot.
HW060000955:admin>
The time of the clock built in the FC Switch Module is based on the UTC.
Setting the difference of the time from the UTC allows the local time to be
displayed instead.
- 141 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Set the time of the built-in clock by using the "date" command.
<Example of time setting>
HW060000955:admin> date "0627220706"
Wed Junv 27 22:07:00 Localtime 2006
HW060000955:admin>
Command parameters:
date "mmddhhmmyy"
Parameters:mm = Month (00 – 12)
dd = Date (00 – 31)
hh = Hour (00 – 23)
mm = Minute (00 – 59)
yy = Lower two digits of dominical year (00 - 99)
Setting Time Server
1. Type "tsclockserver" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. Check the current setting of the time server.
<Checking time server setting>
HW060000955:admin> tsclockserver
LOCL
HW060000955:admin>
"LOCL" appears if the time server is not set.
3. Set the time server by using the "tsclockserver" command on the console screen.
Type "tsclockserver xxx.xxx.xxx.xxx" to set the time server.
Value "xxx.xxx.xxx.xxx" is the IP address of the time server to be set.
<Time server setting>
HW060000951:admin> tsclockserver 192.168.1.1
Updating Clock Server configuration...done.
HW060000951:admin>
For the IP address of an available time server, contact your system
administrator.
4. After setting, type "tsclockserver" on the console screen to check the setting.
<Checking time server setting>
HW060000951:admin> tsclockserver
192.168.1.1
HW060000951:admin>
The IP address of the time server being set appears.
- 142 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Time Server Setting
1. Type "tsclockserver" on the console screen.
Any commands used on the switch console should be specified with
lowercase letters.
2. Check the setting of the current time server.
<Checking time server setting>
HW060000951:admin> tsclockserver
192.168.1.1
HW060000951:admin>
The IP address of the time server being set appears.
3. Type "tsclockserver LOCL" on the console screen.
"LOCL" should be uppercase letters.
<Change of setting>
HW060000951:admin> tsclockserver LOCL
Updating Clock Server configuration...done.
HW060000951:admin>
4. Type "tsclockserver" on the console screen to confirm that "LOCL" appears.
<Change of setting>
HW060000955:admin> tsclockserver
LOCL
HW060000955:admin>
If the time server setting is deleted, "LOCL" appears.
- 143 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving/Restoring Setting Values
Information set on the FC Switch Module can be saved or reset by using the configupload or
configdownload command.
To run commands saving the setting of the FC Switch Module, an FTP
server is required additionally. Prepare a proper FTP server before saving.
The configupload and configdownload commands do not change the name
and IP address of the FC Switch Module. After executing configdownload,
change them by using respective commands.
Saving of settings on FC Switch Modules is required in system recovery
including device replacement due to a system fault. If a new FC Switch
Module is installed or some setting on an FC Switch Module is changed,
save the settings on the FC Switch Module.
1. Transmit setting file to FTP server.
Using the "configupload" command allows a setting file to be transmitted to the FTP server.
Format of "configupload" command
configupload
Protocol (scp or ftp) [ftp]:
← Command
← Transmission protocol
Server Name or IP Address [host]: ← IP address of FTP server
User Name [user]:
File Name [config.txt]:
Password:
← User name of FTP server
← File name
← Password of FTP server
The values in angle brackets ([ ]) are defaults.
2. Transmit setting file to FC Switch Module
Using the "configdownload" command allows a setting file to be transmitted to the FC Switch
Module.
Format of "configdownload" command
configdownload
← Command
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]:
User Name [user]:
File Name [config.txt]:
Password:
← Transmission protocol
← IP address of FTP server
← User name of FTP server
← File name
← Password of FTP server
*** CAUTION ***
This command is used to download a backed-up configuration
for a specific switch. If using a file from a different
switch, this file's configuration settings will override
any current switch settings. Downloading a configuration
file, which was uploaded from a different type of switch,
may cause this switch to fail. A switch reboot might be
required for some parameter changes to take effect.
Do you want to continue [y/n]:
←
Specify whether transmission is enabled or
disabled.
The values in angle brackets ([ ]) are defaults.
- 144 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving Setting
1. Confirm that the FC Switch Module is connected to the proper network.
To save the setting information, various settings in the FC Switch Module
must be stored in a text file to be transmitted to the FPT server. Accordingly,
the FC Switch Module must be connected to the network.
2. Confirm that the FTP server is accessible.
To save the information set on the FC Switch Module, transmit the text file
containing the setting information to the FTP server.
3. Login to the console on the FC Switch Module.
4. Type "configupload" on the console screen.
WH040000556:admin> configupload
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]: 192.168.1.90
User Name [user]: switch
File Name [config.txt]:
Password:
Upload complete
WH040000556:admin>
For the IP address, user ID and password of the FTP server to which the
setting file is transmitted, contact the administrator of the FTP server you
use.
Setting file "config.txt" is transmitted to the home directory of the FTP server.
To change the name of the setting file, enter the new file name in the File
Name field.
5. Confirm that the text file of the name "config.txt" or specified by the configupload command is
transmitted to the home directory of the FTP server.
- 145 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring Setting Information
1. Confirm that the FC Switch Module is connected to the proper network.
To restore the setting information, various settings in the FC Switch Module
must be stored in a text file to be transmitted to the FPT server. Accordingly,
the FC Switch Module must be connected to the network.
2. Confirm that the FTP server is accessible.
To restore the information set on the FC Switch Module, transmit the text file
containing the setting information to the FTP server.
3. Login to the console on the FC Switch Module.
4. Type "switchdisable" on the console screen.
The setting file cannot be reset during system operation.
Running the command causes the FC Switch Module to be disabled.
5. Type "configdownload" on the console screen.
WH040000556:admin> configdownload
Protocol (scp or ftp) [ftp]:
Server Name or IP Address [host]: 192.168.1.90
User Name [user]: switch
File Name [config.txt]:
Password:
*** CAUTION ***
This command is used to download a backed-up configuration
for a specific switch. If using a file from a different
switch, this file's configuration settings will override
any current switch settings. Downloading a configuration
file, which was uploaded from a different type of switch,
may cause this switch to fail. A switch reboot might be
required for some parameter changes to take effect.
Do you want to continue [y/n]: y
fwConfigReload: Fabric Watch configuration reloaded.
download completed.
WH040000556:admin>
6. Type "switchenable" on the console screen.
Running the command causes the FC Switch Module to be enabled.
7. Check the following settings on the FC Switch Module.
Domain ID
Zoning setting
Port setting
Other setting items
8. Type "reboot" on the console screen.
A part of information set by "configdownload" is enabled after the FC Switch
Module is rebooted. To enable all settings, always reboot the FC Switch
Module.
9. Confirm that the FC Switch Module is started normally.
- 146 -
Download from Www.Somanuals.com. All Manuals Search And Download.
N8406-019/ N8406-020 FC スイッチモジュール
取扱説明書
856-083456-010- A
2007 年 3 月 第 5 版
日 本 電 気 株 式 会 社
東京都港区芝五丁目7番1号
TEL (03) 3454-1111 (大代表)
Fibre Channel Switch Module User’s Guide
856-083456-010- A
March 2007, 5th Edition
NEC Corporation
7-1 Shiba 5-Chome,Minato-Ku
Tokyo 108-8001,Japan
© NEC Corporation 2006,2007
乱丁・落丁の場合は交換いたします。
この取扱説明書は再生紙を使用しています。
This guide is made from recycleed paper.
- 147 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|