Operating and Installation
Instructions
Refrigerator
K 1801 SF
K 1811 SF
K 1901 SF
K 1911 SF
en - US, CA
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
M.-Nr. 07 682 390
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Side panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Adjusting the door opening angle (optional accessory) . . . . . . . . . . . . . . . . . . . . 38
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
RemoteVision module installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Preparing the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Sliding the appliance into the installation space . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Attaching the appliance to the installation niche. . . . . . . . . . . . . . . . . . . . . . . . . . 49
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
RemoteVision (optional accessory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using the appliance, follow
basic safety precautions, including
the following:
Electrical Safety
Before installation, make sure that
~
the voltage and frequency listed on the
data plate correspond with the
Read all instructions before
installation and use to prevent
accidents and machine damage.
household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.
Before installation or service,
~
This appliance is intended for
disconnect the power supply to the
work area by unplugging the unit,
"tripping" the circuit breaker or
removing the fuse.
residential use only. Use only as
described in this Operating manual.
Only use the appliance for its
intended purpose.
Do not use an extension cord to
~
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance
(e.g., danger of overheating).
This appliance complies with current
safety requirements. Improper use
of the appliance can lead to
personal injury and material
damage.
Be certain your appliance is
~
properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.
Keep these operating instructions in
a safe place and pass them on to
any future user.
Only connect power to the
~
appliance when all installation work is
complete.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Installation
Use
Persons who lack physical, sensory
~
This appliance is top-heavy and
must be secured to prevent the
possibility of tipping forward.
Keep the door closed until the
appliance is completely installed
and secured per the installation
instructions.
or mental abilities, or experience with
the machine should not use it without
supervision or instruction by a
responsible person.
To reduce the risk of injury, do not
~
allow children to play in, on or near the
appliance, especially in the door hinge
area.
This appliance must be installed
~
and connected in compliance with the
installation instructions.
After your refrigerator is in operation,
~
do not touch the cold surfaces in the
refrigerator compartment, particularly
when hands are damp or wet. Skin may
adhere to these extremely cold
surfaces.
Installation and repair work should
~
be performed by a Miele authorized
service technician. Work by unqualified
persons could be dangerous and may
void the warranty.
Do not store or use gasoline or other
~
Installation must comply with local
flammable vapors and liquids in the
vicinity of this or any other appliance.
~
regulations and state laws.
Do not operate any appliance with a
Do not use any oils or grease on the
~
~
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical Ser-
vice Department.
door seal, as these will cause the seal
to deteriorate and become porous with
time.
Do not block the ventilation gaps in
~
This equipment is not designed for
the plinth or the top of the appliance
housing unit, as this can impair the
efficiency of the appliance, increase the
electricity consumption and cause
damage to the appliance.
~
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft.
Do not install the refrigerator in a
~
room with too low an ambient
Never use a steam cleaner to clean
~
temperature, e.g., a garage, as this
may lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
the appliance. Pressurized steam could
damage electrical components and
cause a short circuit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Disposal of your old appliance
Before disposing of an old
~
appliance, first make the door latch or
lock unusable.
Take off the door.
~
Leave the shelves in place so that
~
children may not easily climb inside.
Consult with your municipal policy
~
on recycling.
Be careful not to damage any part of
~
the pipework while awaiting disposal
by:
-
puncturing the refrigerant
channels in the evaporator.
bending any pipework.
-
-
scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
Your old refrigerator may have a
~
cooling system that used CFCs
(chlorofluorocarbons). CFCs are believed
to harm stratospheric ozone.
If you intentionally release this CFC
refrigerant, you can be subject to fines
and imprisonment under provisions of
environmental legislation. Make sure the
CFC refrigerant is removed and disposed
of by a qualified technician.
SAVE THESE
INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the refrigerator
aHinged door shelf
bShelves (height adjustable)
cDoor shelves (height adjustable)
dDeli drawer
eControl panel
fMain switch
gHumidity filters
hSmartFresh drawers
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the refrigerator
Control panel
aAccess button "p"
activates the control panel
fFood type(s) to be stored in the
SmartFresh drawers
bRefrigerator
gOn/Off sensor button for the
SuperCool function
cUpper SmartFresh drawer
dLower SmartFresh drawer
hSensor button for the temperature
and door alarm*
eTemperature display
X colder; Y warmer
Allows you to set the desired
temperature in the refrigerator
* Only visible when the relevant
function is activated
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Before using for the first time
Turning the appliance On/Off
The stainless steel surface of the
appliance is protected with a plastic
film, which protects it during shipping.
^ Open the appliance door.
Do not remove this protective film until
the appliance has been completely
installed.
^ Turn the appliance On/Off with the
main switch.
After removing the protective film clean
the exterior surface with the supplied
stainless steel agent. This will aid in
preventing resoiling.
The main switch is located on the
right-side underneath the control panel.
^ Clean the inside of the appliance and
the accessories with a mild solution
of warm water and liquid dish soap.
Dry with a soft cloth.
All zones are switched on or off
together.
Once on, the appliance begins cooling.
When the door is open, the interior
lights come on.
After installing the appliance, wait at
least 30 minutes before switching on
the appliance. During transport,
fluids in the refrigeration system may
have shifted, and will need some
time to settle.
The access button will light in the
control panel.
The preset temperatures (factory
settings) are reached after a few hours.
Do not put any food in the appliance
until the preset temperatures are
reached.
,Switching the appliance off with
the main switch does not safely
isolate it from the power supply.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Using the settings
Depending on the zone selected, you
can now:
When a sensor button has been
selected with a finger touch, it will
appear yellow.
– adjust the temperature,
– select the SuperCool function or
A de-selected button will appear white.
– select settings for the SmartFresh
drawers by food type.
For additional information, see the
corresponding sections in the manual.
^ Touch the access button "p" so it
turns yellow.
^ To de-select a zone touch the sensor
button for that particular zone so that
it turns white or select another sensor
button.
On the control panel you will now see
the sensor buttons for the three
appliance zones.
^ To change settings (e.g., to set the
temperature, etc.), touch the sensor
button for the appliance zone you
wish to set.
^ To leave the settings menu, touch the
access button "p" so it turns white.
The last settings entered are stored.
If the access button is not pressed
the display will go out after approx.
30 secs.
The selected sensor button appears
yellow and depending on the zone
selected, additional sensor buttons will
appear on the control panel.
The sensor buttons for the three
appliance zones now disappear from
the control panel.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Custom settings
Turning the button sound
On/Off
In the custom settings mode you can
select and change functions. The
function possibilities are described in
the respective chapters of this manual.
If you prefer the buttons to be silent
when touched the button sound can be
turned off.
^ Touch the access button "p" so it
turns yellow.
Function
Display text
Temperature
°C - °F
†
RemoteVision
;
Module settings
(optional accessory)
^ Touch the sensor button for the
refrigerator so it turns yellow.
Button sound on/off
=
^ Note the position of the X button, but
do not touch.
Exit Custom Settings
mode
c
^ Touch the access button "p" again so
it turns white.
Only the access button "p" is visible.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ Tap the X button until = appears in
the display.
^ Touch the access button "p" to
confirm.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
^ By touching the X button, you can
choose between:
Turning off for longer periods
of time
= 0 : Button sound is off
= 1 : Button sound is on
= – : Return to menu.
If the appliance is not going to be used
for an extended time (for example,
during a vacation) some precautions
should be taken.
^ Touch the access button "p" to
confirm the setting.
^ Take all food out of the appliance
^ Tap the X button until you see ; in
the display.
^ Turn the appliance off at the main
switch
^ Touch the access button "p".
^ Unplug the appliance
You have now left the Custom settings
mode.
^ Clean the interior
^ Leave the door open to prevent
odors
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm
The appliance is equipped with an
alarm system, to ensure that the
temperature does not rise unnoticed
because of energy loss or an open
door.
Turning the temperature alarm Off
As soon as the alarm condition is
corrected, the alarm signal turns off
and the affected zone stops flashing in
the display. The "alarm" indicator goes
out.
The alarm system is always
operational, it does not need to be
switched on.
Temperature alarm
^ To turn the alarm off early, press
the "alarm" sensor button.
If the temperature becomes too warm,
an alarm sounds, the "alarm" indicator
turns red and flashes. At the same time
the affected zone flashes in the display.
The alarm signal turns off. The "alarm"
indicator remains red and the
corresponding appliance zone
continues to flash until the alarm
condition is corrected.
The alarm will sound and the display
will flash if:
– too much warm air flows into the
appliance, for example when food is
being loaded, re-arranged, or taken
out.
Door alarm
If the appliance door is left open, an
alarm signal will sound and the "alarm"
indicator will turn red after five minutes.
– large amounts of food are loaded at
once.
Turning the door alarm Off
– the power fails.
Once the door is closed the alarm turns
off and the "alarm" indicator goes out. If
the door has not been closed properly,
the alarm will sound again after five
minutes.
^ To turn the alarm off early, press
the "alarm" sensor button. The "alarm"
indicator and signal will turn off.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the temperature
Setting the temperature in the
refrigerator
Temperature range
The temperature can be selected within
the following ranges:
^ Touch the access button "p" so it
turns yellow.
– Refrigerator :
35 to 46° F (2°C to 8°C)
A temperature of 37°F (4°C) in the
refrigerator section is recommended.
^ Touch the sensor button for the
refrigerator so it turns yellow.
The room temperature and the
installation location can affect the time it
takes for the appliance to get to the
desired temperature. If the room
temperature is too high, it may not be
possible for the appliance to reach the
lowest temperature.
^ Use the X and Y buttons next to the
temperature display to set the
temperature warmer or colder.
Tap the X and Y sensor buttons to
raise/lower the temperature 1°, or hold
it down to move through the
temperature range more quickly.
The temperature display on the
operating panel always shows the
desired temperature.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the temperature
Temperature unit
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
(Fahrenheit/Celsius)
The temperature can be displayed in
degrees Fahrenheit (°F) or Celsius (°C).
^ Touch the access button "p" so it
turns yellow.
^ Tap the X button until † appears in
the display.
^ Touch the access button "p" to
confirm.
^ By touching the X button you can
select either Fahrenheit or Celsius for
the temperature display.
† 0: Fahrenheit
^ Touch the sensor button for the
refrigerator section so it turns yellow.
^ Note the position of the X button, but
do not touch.
† 1: Celsius
† –: return to menu
^ Touch the access button "p" again so
it turns white.
^ Touch the access button "p" to
confirm the setting.
Only the access button "p" is visible.
^ Tap the X button until a ; appears in
the display.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ Touch the access button "p".
You have left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartFresh drawers
The SmartFresh drawers provide the
right combination of temperature and
humidity. The result is freshness up to
three times longer than in the other
zones of the refrigerator.
Using the SmartFresh drawers
^ Use the sensor button to select the
desired drawer.
Storage temperatures
For fresh foods that are not adversely
affected by cold, the best range is
The selected sensor button turns
yellow, and the sensor buttons for the
32° - 37°F (0° - 3°C). This helps to keep food choices appear.
the food fresh considerably longer than
in the rest of the refrigerator, spoiling is
minimal.
The temperature is set to approx. 35°F
The most recently selected food type(s)
(1.5°C).
appear yellow.
Humidity
^ Use the sensor buttons to select the
food type(s).
The closer the humidity in the appliance
matches the moisture content of the
food, the more moisture the food will
retain, and the fresher and crisper it will
stay over a longer period of time.
– Several food types can be selected
at the same time.
– To delete a food type, simply press it
again.
The optimal humidity is determined on
the basis of the food stored in the
appliance.
– Depending on the food types
selected, the optimal humidity is
determined for the SmartFresh
drawers.
Proper humidity is assisted by 2
humidity filters located above the
SmartFresh drawers. These filters allow
air to pass through, yet retain moisture.
– The "deli" and "dairy" settings are the
most energy efficient.
^ Touch the access button to confirm
the settings.
^ Place the food in the drawer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartFresh drawers
For optimal storage conditions, it is
always best to store similar foods
together in one drawer.
The upper SmartFresh drawer is the
best place to store moisture
sensitive foods.
Foods that are best stored under dry
conditions
– fresh fish and shellfish, meats,
poultry, sausage, dairy products and
deli salads.
Foods that are best stored under
moist conditions
– fresh produce, e.g., vegetables,
lettuce, herbs, mushrooms,
cabbage, fruit.
Remember that higher moisture levels
can only be attained when the food is
stored unpacked so air can circulate
freely.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the refrigerator efficiently
Different storage zones
Coldest area
Due to the natural circulation of air in
the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
these different zones when placing
food in the appliance.
The coldest area in the refrigerator is
directly above the SmartFresh drawers.
The temperature in the drawers
themselves is even colder.
Use these cold areas in the refrigerator
for all highly perishable foods, such as:
– fish, meat, poultry,
This appliance uses a dynamic
cooling feature to establish a
constant temperature during
cooling. As a result, the differences
between temperature zones are less
pronounced.
– deli meats, store-bought meals,
– dishes or baked goods containing
eggs or cream,
– fresh bread dough, pastry dough,
cake batters,
Leave some space between items, so
air can circulate freely around them.
Make sure the ventilation slits are not
covered - this is important for the
cooling performance.
– dairy products.
If storing high-proof alcohol, make
sure it is tightly closed and stored
upright.
Warmest area
Do not store cooking oil in the
refrigerator door. Traces of oil can
cause stress cracks to occur in the
plastic components in the door.
The warmest area is in the top section
of the door. Use this area to store items
such as butter and cheese.
Do not allow food to touch the rear
wall of the appliance, it may freeze
to the wall.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SuperCool
When the SuperCool function is
activated, the appliance is cooled as
cold and quickly as possible (to a
factory-preset temperature).
Switching off SuperCool
The SuperCool function automatically
switches off after approx. 6 hours. The
sensor button turns white, and the
appliance continues running at normal
power.
The SuperCool function is ideal for the
rapid cooling of drinks and for
refrigerating large quantities of foods.
To save energy, the SuperCool function
can be switched off early, once the
food and/or drinks are sufficiently
chilled.
Switching on SuperCool
^ Touch the sensor button for the
refrigerator so it turns yellow.
^ Touch the SuperCool sensor button
so that it turns white.
The temperature display for the zone
selected returns to the original
temperature setting.
^ Touch the SuperCool sensor button
so it turns yellow.
The appliance now continues running
at normal power.
In the temperature display for the
refrigerator zone, the new temperature
setting appears, 35°F (2°C).
The temperature in the appliance now
begins to fall, with maximum cooling in
the refrigerator zone.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic defrost
Refrigerator and SmartFresh
drawers
The refrigerator and SmartFresh
drawers defrost automatically.
During normal operation, condensate
and frost can form on the rear wall of
the refrigerator and drawers.
You do not need to remove this
build-up, it will defrost and evaporate
automatically with the heat generated
by the appliance.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
Moving the shelves
Deli drawer
The shelves can be adjusted according This drawer is set on telescopic tracks.
to the height of the food.
It can be pulled in and out for loading
and unloading, or removed for
cleaning.
^ Using both hands, grasp the shelf
from underneath and lift slightly so
that the rear of the shelf is slightly
above the mountings.
^ Open the drawer.
^ Pull the shelf forward.
^ Move the shelf to the desired height,
then insert the (rear) hooks into
place.
^ Make sure the shelf is level.
^ On both sides of the drawer, pull the
latches (see arrow) upward and lift
the drawer out of the refrigerator.
Push the tracks back into the
refrigerator to avoid injury.
Replacing the drawer
^ Completely extend the telescopic
tracks.
^ Lay the drawer onto the tracks so that
it connects in the front and back.
^ Slide the drawer in.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
SmartFresh drawer
Replacing the drawer
These drawers are set on telescopic
tracks. They can be pulled in and out
for loading and unloading, or removed
for cleaning.
^ Completely extend the telescopic
tracks.
^ Lay the drawer onto the tracks so that
it connects in the front and back.
^ Turn the safety lock back to the
vertical position.
^ Slide the drawer in.
^ Open the drawer.
On the hinged side of the door is a
safety lock, which must be turned to a
horizontal position before the drawer
can be removed.
^ Using a suitable object, e.g., coin,
turn the safety lock to a horizontal
position a.
^ On both sides of the drawer, pull the
latches b upward and lift the drawer
out of the refrigerator.
Push the tracks back into the
refrigerator to avoid injury.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
Adjusting the door shelves
Removing a door shelf
For easier loading, unloading, and
cleaning, the door shelves can be
shifted or completely removed.
^ Slide it upward all the way to the top
of the slide-rails, until it can be
removed.
Replacing a door shelf
^ Start at the top of the slide-rails and
slide the shelf down into the desired
position.
Removing the hinged door shelf
^ Pull the stops upward and out of the
shelf, and remove the shelf lid
upward.
^ Now remove the hinged container
upward and out.
Removing the storage shelf
from above the drawer
^ Using both hands, grasp the door
shelf by the frame and tip it slightly
forward.
^ Remove the rear finishing strip, move
the glass plate slightly toward the
rear, and carefully lift it upward and
out.
^ Slide the tipped shelf up or down
along the slide-rails, and click it into
place with the lower hooks.
^ Make sure the shelf is level.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Before cleaning
To reduce the risk of electrical
shock, disconnect the appliance
from the power supply by shutting
off the power main, tripping the
circuit breaker or unplugging the
power cord before maintenance.
^ Use the main switch to turn the
appliance off completely.
Never use cleaning agents
The main switch is located on the
containing abrasive substances
such as sand, soda, acids, chlorides
or chemical solvents.
right-side underneath the control panel.
^ Unplug the power cord.
Non-abrasive cleaning agents are
also unsuitable, as they can cause
matte areas to appear.
^ Remove any food from the appliance
and store it in a cool place.
^ Take out any removable parts,
e.g., shelves.
Stainless steel surfaces can be
cleaned using a non-abrasive
stainless steel cleaner (available
from Miele).
Cleaning the interior and
accessories
Use a mild solution of warm water and
liquid dish soap. Wash all accessories
and drawers by hand. Do not wash in a
dishwasher.
Only use a mild solution of warm
water and liquid dish soap to clean
this appliance.
Do not use a steam cleaner to clean
this appliance. Pressurized steam
could penetrate electrical
components and cause a short
circuit.
^ Clean the appliance as needed.
^ After washing, wipe down the interior
and accessories with a clean wet
cloth, then dry with a soft cloth. Leave
the appliance door open for a short
time, so the moisture can evaporate.
Do not allow water to get into the
electronic unit or lights.
Appliance door
^ Stainless steel surfaces can be
cleaned using a non-abrasive
stainless steel cleaner.
^ To help prevent resoiling, a
conditioner for stainless steel can
also be used. Apply sparingly with
even pressure.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Aluminum frames
The shelf frames are made of
aluminum.
^ Clean the frames with a mild solution
of warm water and liquid dish soap.
Aluminum is susceptible to
scratches and nicks, treat with care.
^ Unhook the filter cover a in each
side of the drawer and remove them
along with the filters downwards
starting from b.
The aluminum frames may become
discolored or otherwise altered if
soiling is not cleaned away
promptly.
Do not use stainless steel cleaners;
lime removers; scouring pads, such
as pot scrubbers; or used sponges
that still contain abrasive cleanser
residue to clean the frames.
Humidity filters
The two humidity filters, located above
the SmartFresh drawers, must be
removed for cleaning.
^ Clean the filters by rinsing them with
lukewarm water.
Do not clean in a dishwasher or
washing machine. This will damage
the filter.
^ Air-dry the filters.
^ Place the filters back in the filter
cover.
^ Remove the SmartFresh drawer.
^ Put the filter cover back in place,
inserting the rear hooks first.
^ Re-insert the SmartFresh drawer.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Ventilation slits
After cleaning
^ Check the ventilation slits in the base ^ Return all shelves and accessories.
panel regularly. Remove any dirt/dust
^ Place food back in the refrigerator
with a vacuum cleaner or brush.
and drawers.
Clean as needed.
^ Close the appliance door.
Door seals
^ Insert the plug in the socket and
switch the appliance on.
Do not use oil or grease on the door
seals. This may cause the seals to
deteriorate and become porous over
time.
^ Clean the door seals with water and
dry thoroughly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Changing the light bulb
Never touch a halogen bulb with
bare fingers.
The lighting automatically switches off
after the door has been open for
When inserting a glass halogen
bulb, always hold with a soft cloth.
approx. 5 minutes. This is not a fault.
After the bulb has cooled for a short
time it will turn on again.
If the light does not come on when the
door is opened briefly, the light bulb
should be changed.
^ Use the main switch to turn the
appliance off.
To reduce the risk of electric shock,
disconnect the appliance from the
power supply by unplugging or tripping
the circuit breaker.
^ Remove the defective light bulb.
^ Place the new bulb in the socket.
Halogen bulb type:
Upper lighting
20 W/12 V/socket GY 6.35.
^ Slip the rear of the light cover back
into position, then pull it forward and
into place.
^ Grasp the front of the light cover with
both hands, and slide it back.
^ Carefully pull the cover forward and
out.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Side lighting
^ Turn the light cover counterclockwise
and pull out.
Never touch a halogen bulb with
bare fingers.
When inserting a glass halogen
bulb, always hold with a soft cloth.
^ Pull the defective light bulb from the
socket.
^ Place the new bulb in the socket.
Halogen bulb type:
5 W/12 V/socket G 4.
^ Put the light cover back on and turn
clockwise into place.
^ Restore power to the appliance.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
With the aid of the following guide minor problems can be corrected without a ser-
vice call.
Repairs should only be carried out by a qualified and trained person in strict
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage and may void the warranty.
Issue
Possible fault
Solution
The refrigerator does The machine is not
Check whether the appliance
is switched on at the main
switch. The temperature
display must be lit up.
not get cold.
turned on.
The machine is not
plugged in.
Check that the plug is
correctly inserted in the power
outlet.
Check that the fuse has Reset the circuit breaker.
not tripped.
The temperature is set
incorrectly.
Check the display.
Issue
Possible fault
Solution
The temperature in
the refrigerator is
too low.
Select a warmer
temperature.
See "Selecting the correct
temperature".
The SuperCool function SuperCool automatically shuts
is still on.
off after 6 hours.
The door is not closed.
Check that the door has been
closed properly.
A large amount of food is This makes the compressor
put in the refrigerator at run longer, causing the
the same time. temperature to fall
automatically.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Issue
Possible fault
Solution
The compressor kicks
on very frequently and
for too long.
The ventilation slits are
covered or dusty.
Clean with a vacuum or
brush.
The door has been
Once the fridge gets
opened too frequently, or down to the set
a large amount of fresh
food has been put in at
once.
temperature the
compressor will turn off.
The door is not closed.
Check that the door has
been closed properly.
Issue
Possible fault
Solution
The alarm is ringing.
The appliance door has
been open for longer than
5 minutes.
Close the door.
Issue
Possible fault
Solution
The alarm is ringing and The door is not closed.
Once the alarm condition
has been corrected, the
alarm will turn off and the
"alarm" indicator will stop
flashing.
the "alarm" indicator is
A large amount of food
flashing.
was loaded at the same
time.
There has been a power
failure.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
The appliance is making noises.
Issue
Possible fault
Solution
Brrrrr...
Humming noise made by the These noises are not a
compressor. This noise can
get louder for brief periods
when the motor is switching
on.
fault.
The noise of the
compressor and the
coolant circulating in the
system is unavoidable.
Blubb, blubb....
Click....
A gurgling noise can be
heard when coolant is
circulating through the pipes.
Clicking sounds are made
when the thermostat switches
the compressor on and off.
Sssrrrrr....
On multi-zone and frost-free
appliances you can
sometimes just hear the
movement of air circulating
inside the appliance.
Rattling, vibrating
The appliance is uneven.
Realign the appliance
using a level, by raising or
lowering the screw feet
underneath the appliance.
The appliance is touching
another appliance or piece of
furniture.
Move it away.
Drawers, baskets or shelves Check all removable
are unstable or sticking.
items and refit them
correctly.
Bottles or containers are
unstable or knocking against
each other.
Separate them.
The transport cable clips are Remove the clips.
hanging loose at the back of
the appliance.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
In the event of a fault which you cannot MieleCare
easily fix yourself, please contact the
(USA only)
Miele Technical Service Department at
the address on the back of this booklet. MieleCare, our Extended Service
Contract program; gives you the
When contacting the Technical Service
assurance of knowing that your
Department, please quote the model
appliance investment is covered by 5
and serial number of your appliance
years of worry-free ownership.
given on the data plate inside the
MieleCare is the only Extended Service
appliance.
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory-trained professionals can
guarantee the safety, reliability and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by the Miele Ser-
vice department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation instructions
To prevent accidents
and machine damage
read these instructions
before
installation or use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of packing materials
Disposal of an old appliance
The cardboard box and packing
materials are biodegradable and
recyclable. Please recycle.
Old appliances contain materials that
can be recycled. Please contact your
local recycling center about the
possibility of recycling these materials.
Ensure that any plastic wrappings,
bags, etc., are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Before discarding an old appliance,
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
Have the appliance installed by a
qualified technician, according to
the enclosed installation instructions.
The appliance should be installed in a
dry, well-ventilated room.
Do not install the appliance:
- outdoors
,WARNING
- in an environment with dripping
water
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
- in rooms that are at risk of frost.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.
The installation location should not be
exposed to direct sunlight, nor near a
heat source, such as an oven,
radiator, etc.
The ambient temperature should not
drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions
may occur.
Empty weight of your machine:
K 18X1 SF. . . . . . . . . . 476 lbs (216 kg)
K 19X1 SF . . . . . . . . . 516 lbs (234 kg)
If installation next to a heat source is
unavoidable, use a suitable insulating
plate or observe the following minimum
distances from the heat source:
– 1 1/4" (3 cm) from an electric cooktop
or oven.
– 12" (30 cm) from a gas cooktop or
oven.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Base
Ventilation
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor
must meet the following requirements:
The air intake and outlet must not be
blocked or covered in any way. They
also need to be dusted/cleaned on a
regular basis.
K 18X1 SF . . . . . . . . 1,056 lbs (479 kg)
K 19X1 SF . . . . . . . . 1,254 lbs (569 kg)
Installation niche
To ensure that the appliance is installed
securely and functions properly, the
base must be flat, level and made of a
hard, rigid material.
To ensure safe, trouble-free installation
and the best possible cosmetic result,
check to be sure that the installation
space complies with the installation
dimensions. See "Niche dimensions".
If in doubt, contact Miele.
The side walls of the installation cavity
must be plumb.
Furniture/fixtures
The new appliance will be mounted
securely to adjacent furniture/fixtures.
For this reason, it is essential that all
attachable furniture/fixtures be
connected securely to the floor or wall
by a suitable means.
The minimum thickness of the side
walls and the top wall must be 5/8"
(16 mm).
The minimum thickness of the toe-kick
cover must be ½" (13 mm). A thickness
of 3/4" (19 mm) is recommended.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation options
Side-by-side
There are many different installation
options. You are limited only by the
design of the kitchen.
This appliance can be installed
"side-by-side" with another
fridge/freezer using a "Merging Kit".
The "Merging Kit" is available from
Miele.
The door hinge cannot be
exchanged.
Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.
Single column
The appliance can be installed at any
preferred location in the kitchen.
However, be sure the door will open
and close properly in the chosen
location.
For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.
Appliances attached together using
the "Merging Kit"
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation with partition using the
"Merging Kit"
Side panels
If one side of the appliance is visible, a
side panel must be used.
The side panel must be firmly secured
to the wall, the floor and the overhead
furniture/fixtures before the appliance is
placed in the cavity.
The dimensions of the side panel are
taken from the opposite wall of the
installation space. During installation,
ensure that the cavity is square and the
measurements are correct.
Adjusting the door opening
angle (optional accessory)
The minimum thickness of the partition
is 5/8" (16 mm).
Depending on the installation site, it
may be necessary to adjust the door
opening angle to 90°.
If there is a partition with a thickness
from 5/8" (16 mm) to 6 5/16" (160 mm)
between the adjacent appliances, then
each appliance should be individually
installed within its own niche using the
mounting accessories included.
^ Open the door.
The "Merging Kit" will also be needed.
The "Merging Kit" is available from
Miele.
Installation with partition without
using the "Merging Kit"
If there is a partition with a thickness of
more than 6 5/16" (160 mm) between
the adjacent appliances, then each
appliance should be individually
installed within its own niche using the
mounting accessories included (the
"Merging Kit" is not necessary).
^ Insert the banking pin through the
holes and drive in with a hammer.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Niche dimensions
A
B
K 18X1 SF
K 19X1 SF
30 ½" (774.6 mm)
36 ½" (927 mm)
30" (762 mm)
36" (915 mm)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Power supply
1. Power supply
A
K 18X1 SF
K 19X1 SF
15" (381 mm)
18" (458 mm)
Door dimensions (open min. 90°)
A
K 18X1 SF
K 19X1 SF
32 5/8" (829 mm)
38 11/16" (982 mm)
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Before you begin
Tools needed for installation
– Cutter with adjustable blade
– Cordless screwdriver T 20
– Torx screwdriver T 20
Read these instructions completely
and carefully.
Have the appliance installed by a
qualified technician, according to
the enclosed installation instructions.
– Hammer drill for drilling holes in wall
or floor
– Wood drills in different sizes
– Hammer
To reduce the risk of injury or
damage to the product, two people
should be used for installation.
– Open-ended wrench ½" (SW 13 mm)
– Box-end wrench
These installation instructions are
intended for use by qualified installers.
In addition to these instructions, the
appliance must be installed in
accordance with all local codes. In the
absence of a local code, the following
should be used:
–
5/16" (8 mm) hex nut driver
– Adhesive tape
– Multi-grip pliers
– Level
– In the USA, the National Electric
Code, ANSI/NFPA 70 - latest
edition/State and Municipal codes
and/or local codes.
– Metal tape measure
– Square
Other
– In Canada, the Canadian Electric
code C22.1 - latest edition/Provincial
and Municipal codes and/or local
codes.
– Stepladder
– Dolly, hand truck
– Wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] as an alternative
tilt protection, length depends on the
width of the installation cavity)
– Wood screws in different sizes
Optional accessories
– "Merging Kit" for side-by-side
installation
– RemoteVision module for wireless
monitoring
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Check the installation niche
Before installation
To ensure a safe, trouble-free
,Caution - the appliance is very
heavy. Use caution when unpacking
and opening the door, danger of
tipping.
installation and the best possible
cosmetic result, check to be sure
that the installation space complies
with the installation requirements.
^ To protect the base from damage
during installation, attach a hard
board, linoleum, etc., to the floor in
front of the intended installation
location.
^ Check the base (see "Installation").
^ Check the dimensions of the cavity.
^ Check that the cavity is square.
^ Check the location of the power
outlet.
^ Take the supplied accessories out of
the protective packaging.
^ Check that all furniture parts in the
vicinity of the appliance are securely
connected to the wall.
There are transportation safety
devices inside the appliance to
protect the shelves and storage
compartments until installation is
complete. Do not remove them, or
parts may be damaged.
^ Check that the adjacent
furniture/fixtures do not collide with
the open door.
^ Check the appliance for damage in
transit.
Do not install the appliance if it is
visibly damaged. If in doubt, contact
your dealer.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Loosen the bracket that holds the
appliance to the pallet.
^ Unscrew the screws a on the cover
b and pull off the sticker c.
,Caution! The appliance is no
longer secured and may be
unstable.
^ Remove the cover b.
^ From the rear of the appliance
carefully lift it from the pallet.
Once the appliance is on the ground it
can be wheeled around.
RemoteVision module
installation
^ Push the module into the slot until it
locks into place.
(optional accessory)
^ Connect the appliance to the power
supply and turn it on. After several
seconds the indicator light will come
on.
Always disconnect the appliance
from the power supply when
performing installation, maintenance
or service work.
Install the RemoteVision module
before placing the appliance in its
installation niche.
The indicator light will display different
colors one after the other; any control
light at the end indicates that the
module was correctly installed.
Once connected the RemoteVision
module will increase the energy
consumption of the appliance.
The slot for the RemoteVision module is
located in the lower area of the back of
your appliance.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
If the indicator light does not come on,
installation of the module was
Preparing the installation
niche
unsuccessful. In that case, repeat the
process. If that does not correct the
problem, contact Miele.
Keep the appliance door closed
until it is securely fastened in the
niche. Tipping hazard.
^ Pull the antenna d straight out.
If the installation niche is deeper than
the appliance, a solid wooden beam a
can be placed behind the anti-tip
brackets b so the appliance can be
securely attached to the base or wall.
^ Guide the cover b over the antenna
d and screw on the cover.
The length of the wooden beam a
should be to the width of the installation
space.
^ Angle the antenna d so that it faces
to the right or left.
^ If necessary, disconnect the power
supply and continue installing the
appliance.
If possible, always screw the
wooden beam into existing studs.
Mounting Accessories
The mounting accessories needed for
installing the appliance into the niche
are included in the packaging. Several
plastic bags are included which are
numbered alphabetically.
The bag needed for each step will be
marked with its respective letter.
^ Use the included Torx screwdriver to
tighten the screws.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Anti-tip brackets
The anti-tip brackets help keep the
appliance safely attached to the
installation space, which helps prevent
tipping.
Two anti-tip brackets are
recommended for each appliance or
appliance combination (side-by-side).
^ Drill pilot holes:
–
1/8" (3 mm) for the 5 x 60 mm wood
screws
–
1/16" (2 mm) for the 4 x 15 mm wood
screws.
The distance "D" between the anti-tip
brackets b is the width of the
appliance.
^ Tightly secure the anti-tip brackets in
the niche.
Be certain the screws penetrate
through the flooring and into the wall
plate a minimum of 3/4" (19 mm).
^ Position the anti-tip brackets b on
the left and right walls of the
appliance niche.
^ Mark the holes through the anti-tip
brackets b on the floor of the
installation niche.
^ Set the brackets aside.
Assure that there are no electrical
wires in the area which the screws
could penetrate - risk of injury and
damage.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Securing an alternative anti-tip
device
The length is equal to the width of the
installation niche.
If the anti-tip brackets cannot be
attached securely, an alternative
anti-tip device can be used.
– If the installation niche is deeper than
the appliance, select a beam with a
larger cross section, or attach two
beams.
Ensure that there is no "give" between
the appliance and the anti-tip device.
– The beam must cover the appliance
by at least 2" (50.8 mm).
If possible, always screw the
wooden beam to existing studs.
^ Mark the installation height (lower
edge of the beam) on the rear wall of
the niche.
^ Select screws according to the
thickness of the wooden beam.
Example: 3 ½" (89 mm) screw for 2x4
beam.
^ Determine the number of screws
based on the cavity width, to ensure
that the beam will be attached
securely.
^ Locate wall studs near the rear wall
of the cavity and mark drill holes in
the beam.
^ Pre-drill the wooden beam.
^ Attach the wooden beam to the rear
wall of the niche.
If a side-by-side installation is
desired, connect the two appliances
together. See the Installation Manual
included with the "Merging Kit".
^ Cut a wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] to the required
length).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Sliding the appliance into the
installation space
The plug of the appliance should be
easily accessible after installation.
If the plug is not accessible after the
appliance has been installed,
disconnection from the power
supply should be completed via the
circuit breaker.
In the case of side-by-side
installations, a separate outlet must
be used for each appliance.
^ To prevent the power cord from
becoming caught:
Tie a piece of string to the middle of
the power cord and feed it forward
under the appliance. When sliding
the appliance in, pull the cable
forward c.
^ Unscrew the plinth.
^ Carefully slide the appliance into the
space until the height-adjustable
wheels interlock with the anti-tip
brackets d.
If resistance is felt when attempting to
slide the appliance into the installation
niche - for example, because the floor
is uneven,
^ Turn the rear adjustable wheels
slightly outward (see "Aligning the
appliance"), then push the appliance
in.
^ To protect the corners of the
installation space, attach the
supplied edge protector a on both
sides with adhesive tape.
Be careful not to damage the power
cord attached to the floor.
^ Plug the appliance into the power
outlet b.
^ Remove the edge protector a.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Aligning the appliance
A mark is located on the appliance
base and is used as a standard gauge
for height adjustment. When adjusting
the height, align this mark at 1 1/4"
(32 mm) above the floor.
^ Align the appliance with the
surrounding cabinets.
^ Unscrew the height-adjustable feet
until the mark on the base has
reached the indicated guide
dimension 1 1/4" (32 mm).
The height-adjustable feet at the front
and rear can all be adjusted from the
front.
– Front: with an open-ended wrench
½" (SW 13).
The feet can be adjusted from the
top and bottom e.
^ Check that the appliance is level with
the surrounding cabinets.
– Rear: with a 5/16" (8 mm) hex nut
driver via flexible shaft f.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Note:
Attaching the appliance to the
installation niche
– Do not twist or jam the appliance
inside the niche. When unscrewing
the height-adjustable feet, proceed
gradually, alternating between left
and right.
– The adjustment of the rear feet is
aided if the appliance is lifted at the
rear (tipped forward slightly).
– If using a wooden beam as an
alternative anti-tip device, rotate the
appliance all the way toward the
wooden beam.
– Do not use a power tool to adjust the
rear feet!
^ Open the appliance doors.
^ Fasten the appliance on the left and
right hand sides with the 3 (supplied)
wood screws.
If there is a fairly large gap above the
appliance, cut a wooden beam to fit
exactly and place it in the gap.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Attaching the toe-kick cover
The maximum height of the toe-kick
cover is 4" (101 mm) from the top of
the floor. Do not cover the ventilation
slits in the plinth. Risk of damage to
the appliance.
^ If required, cut the toe-kick cover to
the required length and height.
^ Remove the foil from the adhesive
strips.
^ Attach the toe-kick cover to the
plinth.
^ Attach the plinth to the appliance.
^ Put the included cover plates in
place.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Mounting the air separator
The air separator keeps the supply and
exhaust air separate. This prevents
warm exhaust air from flowing into the
machine, optimizing the energy
performance of the unit.
^ Position the air separator in the
center of the appliance door.
^ From below, screw the air separator
firmly onto the door with the 2
screws.
^ If necessary, shorten the three parts
of the air separator.
^ Insert the foam pieces back into the
sides.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection
to a 120 V, 60 Hz supply.
, Avoid the risk of electrical
shock
- Plug into a grounded 3-prong
outlet.
The fuse rating is 15 amps.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licensed electrician only.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance. Ideally, the power outlet
should be next to the appliance and
easily accessible. Do not connect the
appliance to the power supply by an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (danger of overheating).
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
U1-800-999-1360
V1-800-565-6435
52
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
Miele's RemoteVision Wi-Fi technology
Be sure your wireless system meets the
following requirements
creates a 'virtual link' between your
appliance and our monitoring center. If
a fault occurs, Miele's client service
center will be notified and contact you,
or another trusted individual identified
on your call roster, in order to gain
access to your appliance to fix the
problem.
– A wireless router that supports an
IEEE 802.11b protocol
– Windows XP® or newer operating
system, Mac® OS X 10.3 or higher
– Cable or DSL modem
– Microsoft® Internet Explorer 6 or
higher, Safari 2.0 or higher, Firefox
1.5 or higher
For information on set-up and
installation of the RemoteVision module
see the "Installation" section of this
manual.
* Please note that each wireless router
manufacturer supplies their own device
drivers and setup programs. Due to the
differences in manufacturers, exact
router setup instructions are not
included in this manual. Wording and
instructions may vary.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
Accessing the RemoteVision
control panel
^ Tap the X button until ; appears in
the display.
^ Touch the access button "p" to
confirm.
^ Touch the access button "p" so it
turns yellow.
See the table on the following page for
a description of each setting in the
display.
^ Use the Y or X buttons to select the
RemoteVision options.
^ Touch the sensor button for the
refrigerator section so it turns yellow.
^ Note the position of the X button, but
do not touch.
The module has been connected to
the network when ; # appears in the
display.
^ Touch the access button "p" again so
it turns white.
If ; # does not appear, refer to the
"Network options" section of the
XKM 2000 Installation Instruction
manual.
Only the access button "p" is visible.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ Press and hold the access button "p"
for 2 seconds to confirm the change.
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ To return to the main menu, tap the X
button until a solid ; - appears in the
display.
^ Press the access button "p" to
confirm.
^ Tap the X button until a ; appears in
the display.
^ Touch the access button "p".
Access to the Custom settings mode is
now active for approximately 10
seconds.
You have left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
MasterCool control panel options for RemoteVision
Status indicators Description of function
Flashing ; ~
Flashing ; ‡
Flashing ; |
Module booting phase
Not connected to network
Connection to network established, no IP address
assigned
Solid
; #
Connected to network
Flashing ; <
In Ad-Hoc Mode, not connected
In Ad-Hoc Mode, connected
Flashing ; =
Selectable
options
Description of function
; -
; 2
; 3
; 4
Back
Reboot the module
Reset to factory settings
Enter Ad-Hoc Mode
Note: If you cannot select any option (other than ; - "Back", the module has not
been installed correctly.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 4209
M.-Nr. 07 682 390 / 02
K 1801 SF, K 1811 SF, K 1901 SF, K 1911 SF
For the most updated manual see the Miele web site.
Download from Www.Somanuals.com. All Manuals Search And Download.
|