This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device does not cause harmful interference,
and (2) this radio must accept any interference received, including
interference that may cause undesired operation.
Owner’s Manual
For Models G-225 & G-227
GMRS/FRS Radio
To maintain compliance with FCC’s RF exposure guidelines, this transmitter
and its antenna must maintain a separation distance of at least 2 inches from
your body. To transmit, hold the radio with the antenna pointed up and away
from your face, with the radio at least 2 inches from your face. Speak in a
normal voice into the microphone.
FEATURING
•
•
•
•
•
•
•
•
•
22 Channels
38 CTCSS codes
VOX
Monitor function
Call Alert
Back-Lit LCD
Vibrate Alert (G-227 Only)
Scan
Use and Care
1. Do not use alcohol or cleaning solutions to clean the radio.
2. Do not immerse the radio in water.
3. Use a soft damp cloth to clean the radio
4. Dry the radio with dry lint-free cloth should it get wet.
5. Turn off the radio and remove the batteries during long-term storage.
Roger Beep Tone
- 2 -
in the form on the following page and mail it to our address.
Index
Accessories
Accessories order form
Introduction
4
5
6
AVP- 1
AVP-2
FCC Licensing Information
Controls and Buttons
LCD Display
6
7
8
Installing Batteries
Charging the Batteries
Operation
Problems & Solution
Frequency and CTCSS Charts
Technical Specification
Warranty Information
MIDLAND Family Products
9
10
11-18
19-20
21
22
23
24
-
-
2 Over the ear Mic.
Headsets w/ PTT.
-
-
-
One Dual Desk Charger
2 Rechargeable battery packs
1 AC Adapter
-
$39.95
-
$19.95
- 3 -
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the batteries
Installing Batteries
Your G-225/227 is equipped to allow using a rechargeable NiMH battery pack (not included)
which can be recharged by an A/C Charger/Adaptor (not included) through the MIC Jack of the
radio, or using a Desktop Charger (not included). Batteries must be charged when the low
battery icon flashes on the display.
Your G-225/227 radio operates with either 4 AAA Alkaline Batteries or optional NiMH
battery Pack. The belt clip should be removed (Page 18) to ease installation or
removal. To install the batteries:
1. With the back of the radio facing you, remove the Battery Cover by sliding it down
from the unit.
2. Insert 4 AAA batteries observing the polarity as shown. Installing the batteries
incorrectly will prevent the unit from operating or can damage the unit.
3. Return the Battery Cover by sliding it up from the unit.
To charge through the MIC Jack :
- Connect the AC Adaptor/Charger into an A/C Wall Outlet
- Insert the Adaptor/Charger jack into the MIC Jack of the radio found at the side of the unit.
To charge through a Desktop Charger:
- Connect the AC Adaptor into an A/C Wall outlet
- Insert the Adaptor Jack into the Desktop charger jack
- Place the units into the Desktop Charger slot and note that the LED indicator of the Desktop
Charger will light up to indicate charging function.
Note: Batteries are not included
Note :
1. Only use batteries indicated in the manual, or our NiMH battery pack. (see page 4)
2. Do not attempt to charge Alkaline batteries or any batteries or battery packs other than the
one indicated in the manual. This may cause leakage and damage the unit.
3. For long term storage of the radio, turn the unit OFF and remove the batteries from the
radio.
- 9 -
- 10 -
Call Tone : Your G-225/227 can transmit a call tone for a fixed length of time. To
send a call tone, press the PTT twice rapidly. The TX icon will appear during
transmitting a call tone and tone can be heard on the speaker for confirmation.
Operation
Power On/Off : Press the button for more than 1 second to turn the radio
on. Press the button for over 3 seconds to turn the radio off.
Scan : Your G-225/227 can scan all of the 22 channel to observe for any activity. To
enter the scan mode, press the
exit the scan mode.
Your radio will rapidly scan each of the 22 channels and stop on any active channel.
When you press the PTT button to transmit on an active channel, the scanning function
button for one second. Press
button again to
Volume : Press the
to decrease the volume during normal operation.
button to increase the volume, and press the
button
Talking and Listening : To communicate, all radios in your group must be set to the
same channel and CTCSS Code.
will stop. To resume scanning Press and hold the
button for one second.
•
•
For maximum clarity, hold the radio 2 to 3 inches from your mouth.
Press and hold PTT button and speak in a normal voice into the microphone.
The TX icon will appear continuously on the LCD Display when transmitting.
To receive messages, release the PTT button. The RX icon will appear on the
display when your radio is receiving a transmission.
Keypad Lock : To avoid accidentally changing the radio operation, press the
button for 5 seconds . The icon will appear on the display. When the is on the
menu function the and button will be disabled. When locked, you will be
able to turn the radio off and on, monitor, transmit/receive, and send a call tone. To
unlock, press the for 5 seconds.
•
Monitor button : Pressing and holding the
hear noise so you can adjust the volume level of the radio when not receiving a
signal. The should be used to check activity on current channel before
button for 2 seconds will let you
Backlit LCD : Your G-225/227 comes with a backlit LCD Display to enable you to
view the setting in a dark environment. The backlighting can be turned on/off by
transmitting. Press and hold the
for 2 seconds to return to normal operation.
pressing the
button. The backlighting will turn on for 5 seconds.
- 11 -
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
User Interface
To access the advanced features of your G-225/227, your radio has the following
menu functions:
CTCSS Selection : Your G-225/227 has 38 CTCSS codes available. The selected
CTCSS code may be different for each channel. To select a CTCSS code for the
current channel:
G-227 only
•
With the desired channel selected, repeatedly press
current CTCSS Code number flashes.
until the
Vibrate
Mode
Channel
1~22
CTCSS
0~38
Power
Hi/Lo
VOX
Roger
On/Off
•
•
Use the
or
button to change the CTCSS code number.
On/Off
On/Off
Press the PTT button to save the new CTCSS Code or press the
repeatedly until you exit the menu.
Note : The unit will automatically go to normal mode after 5 seconds of no button activity
during menu setting.
Note : Selecting a CTCSS code of “oF” will disable the the CTCSS feature. To
communicate between two , both the channel and CTCSS code selections must be
the same. To communicate with other models and brands of radios the actual radio
frequency and CTCSS frequency must be matched. The frequency chart at the back
of this book are included to help with this selection. In general, the first fourteen
channel selections may be used to communicate with most FRS radios.
Channel Selection : Your G-225/227 has 22 channels available. To change
channels:
•
With the radio on, press
flashes.
until the current channel segment
buttons to change the channel.
•
•
Use the
or
Press the PTT button to save the new channel.
- 13 -
- 14 -
Power Selection : Your G-225/227 has two transmit power levels. To select the
power level on channels 1~7 and 15~22:
Vibrate Alert (G-227 only): Your G-227 is equipped with a Vibrate alert for silent
operation of the radio. The radio will vibrate when receiving a call tone transmission
instead of emitting a call tone sound. To set the unit at Vibrate alert mode:
•
•
Press
Press
until the “Pr” appears on the display.
or to select between high and low power levels. The
•
•
•
Press the
display.
Press the
button repeatedly until the Vibrate icon flashes on the
Hi/Lo icon will alternately appear during setting.
•
Press the PTT button to save and exit.
or button to set the Vibrate alert on or off, an
The HI or LO icon will appear on the display depending on your setting.
“on” or “oF” will appear on the display during setting.
Press the PTT button to save and exit.
Note : On channel 8~14 no power level selection is possible
The Vibrate alert icon will appear on the display when unit is in vibrate mode.
VOX : VOX (voice operated transmit) operation allows you to transmit without using
the PTT button when using a headset. To enable VOX operation:
Roger Beep Tone : Whenever you release the PTT button, a “Roger Beep” tone
may be transmitted to let your friends know you are finished talking. To enable the
•
•
Insert the headset plug(s) into the SPK/MIC jacks.
Set the radio into VOX mode.
Roger Beep, press the
Press the and
button repeatedly until the “rb” appears on the display.
to set the Roger Beep tone on or off. An “on” or “oF”
To set the radio to VOX Mode, repeatedly press the
flashes on the LCD display. Press the or
button until the VOX icon
button to turn the VOX on or off,
will appear on the display during setting.
an “on” or “oF” will appear on the display during setting. The VOX icon will appear
on the LCD display if the radio is set into VOX mode.
- 15 -
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
External Speaker/Microphone Jack : Your G-225/227 can be used with an optional
external speaker/microphone or headset, freeing your hands for other tasks. To use
an optional / speaker / microphone or headset:
Belt Clip :
To install the belt clip:
•
Slide the clip up into the slot on the back of the radio until the latching
mechanism clicks.
•
Insert the plug(s) into the SPK/MIC
jacks
•
Place the earbud into your ear, and
adjust the mic into your desired
position.
To remove the belt clip:
Pull the latching tab outward, then
•
gently slide the belt clip down
toward the bottom of the radio.
- 17 -
- 18 -
PROBLEM
SOLUTION
Technical Specification
A. Specification
No Power
- Check battery installation and/or replace batteries
Channels
22 Channels
UHF 462.5500 ~ 467.7125 MHz
4 AAA Alkaline or rechargeable Ni-MH Batteries
Typically 2 Watts HI, 0.5 Watts LO
Cannot Receive
Messages
- Confirm the radios have the same channel settings.
Operating Frequency
Power Source
Output Power
- Make sure the you are with in range of the other transceivers.
- Buildings and other may interfere with your communication.
B. Current Drain :
Radio is not
- Make sure key lock is not on. See “Keypad Lock” (Page 12).
- Radio might need to be reset. Turn radio off then on.
- Ensure accessory microphone is set properly
•
•
•
Receive : 150mA max
Transmit : 900mA max
Standby : Average 14mA max
responding to
button presses
Display is dim
- Reposition or replace batteries.
C. Operating Time : Based on 900mAH (Alkaline battery) capacity
- Contacts on the bottom of the radio they may require cleaning.
- Ensure the outlet the charger is plugged into is functioning properly.
- Check that the batteries are installed in the radio properly.
•
•
•
•
Talk Time : 1~1.5 hours
Receive Time : 12 hours
Standby Time : 60 hours
Combined (5-5-90 duty) Time : 15 hours
Charger not
functioning
If you have a problem which you believe requires service, please call first and speak
with a service technician. Many problems can be remedied over the phone without
returning the unit for service.
- 19 -
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Channel Frequency Chart
Midland Radio Corporation will repair or replace, at its option without charge, any Midland FRS/GMRS
transceiver which fails due to a defect in material or workmanship within One Year following the initial
consumer purchase. This warranty does not apply to water damage, battery leak or abuse.
CH. No
CH. Freq.
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
CH. No
9
10
11
12
13
14
15
16
CH. Freq.
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
CH. No
17
18
19
20
CH. Freq.
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
1
2
3
4
5
6
7
8
This warranty does not include any carrying cases, earphones, or antennas, which may be a part of or
included with the warranted product, or the cost of labor for removal or re-installation of the product in a
vehicle or other mounting.
Performance of any obligation under this warranty may be obtained by returning the warranted product,
21
22
freight prepaid, along with proof of purchase to:
Midland Radio Corporation
Warranty Service Department
1120 Clay Street
North Kansas City, Missouri 64116
CTCSS Code Chart
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to
state.
Note : The above warranty applies only to merchandise purchased in the United States of America or any of
the territories or possessions thereof, or from a U.S. Military exchange.
Midland Radio Corporation
1120 Clay Street
North Kansas City, MO 64116
Tel: (816) 241-8500
Code
Freq. (Hz)
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
Code
9
Freq. (Hz)
91.5
94.8
Code
Freq. (Hz)
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
Code
25
26
27
28
29
30
31
32
Freq. (Hz)
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
Code
33
34
35
36
Freq. (Hz)
210.7
218.1
225.7
233.6
1
2
3
4
5
6
7
8
17
18
19
20
21
22
23
24
10
11
12
13
14
15
16
97.4
100.0
103.5
107.2
110.9
114.8
37
38
241.8
250.3
E-mail: [email protected]
URL: www.midlandradio.com
- 21 -
- 22 -
Midland Radio Corporation
1120 Clay St.
N. Kansas City MO 64116
Call 816.241.8500
S.A.M.E. Weather
Alert Radios
CB Radios w/ESP
2-Way Radios
Note: Features & Specifications are subject to Change without notice. MIDLAND is not
responsible for unintentional errors or omissions on its packaging.
- 23 -
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|