Plasma-TV-Set 42“ PIP 42TM92
Bedienungsanleitung
Operating Instructions
605 47 0024.A1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Aufstellhinweise
Das Plasma-TV-Set wird mit Plasma-Bildschirm, Standfuß, Wandhalterung, 2 Laut-
sprecher mit Fuß und Tuner-Box ausgeliefert.
Montage Standfuß
Der Standfuß ist mit zwei Blenden ausgestattet. Die hintere hohe Blende, mit dem
Ausschnitt für die Kabeldurchführung, ist mit vier Schrauben am Standfuß befestigt.
Diese Blende vor der Montage des Plasmabildschirms am Standfuß entfernen.
Standfuß in die entsprechende Führung einschieben und mit vier Schrauben
(M5 x 20 mm) vorsichtig festschrauben.
Netzanschlusskabel und Verbindungskabel zur Tuner-Box einstecken, die Kabel
durch den Ausschnitt führen und danach die Blende wieder anschrauben.
Blende vorne, fest
Kabeldurchführung
Blende hoch, hinten, abgeschraubt
Lautsprecher links
Plasmabildschirm
4 Schrauben
M5 x 12mm
Lautsprecher rechts
Lautsprecherhalterung
Standfuß
4 Schrauben
M5 x 20mm
ቢ
Montageschema
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Wandmontage
Nichtbeachtung dieser Hinweise kann zu ernsthaften Verletzungen von Per-
sonen und/oder irreparablen Schäden am Gerät führen.
Der Plasma-Bildschirm darf nur an senkrechten Wänden mit Hilfe der
Wandmontageeinheit befestigt werden.
Führen Sie die Montage der Wandhalterung und das Einhängen des Gerätes
nicht ohne die Hilfe einer zweiten Person durch.
• Gehen Sie bei der Befestigung der Wandhalterung sehr sorgfältig vor. Sie muss
das TV-Gerät nicht nur dauerhaft halten, sondern dem Gerät auch bei Erschütte-
rung, Stößen etc. sicheren Halt ermöglichen.
• Vor der Montage ist die Beschaffenheit der Wand (Stabilität und Wandstärke) zu
untersuchen. Fragen Sie im Eisenwaren-Fachhandel nach entsprechend geeigneten
Metallschrauben und Dübeln.
• Die Wand muss fest und statisch tragfähig sein (z.B. Mauerwerk aus Ziegel, Kalk-
sandstein oder Beton).
• Für abweichende Wandaufbauten wie z.B. Holz-, Hohlraumwände oder andere
Materialien ist unbedingt ein erfahrener Fachmann mit der Montage der Wand-
halterung zu betrauen.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Wandmontage
Wandmontage des Plasma-Bildschirm
1. Um den Plasmabildschirm an der Wand zu montieren, entfernen Sie zuerst den
Standfuß (Abb. 1). Drehen Sie die vier Schrauben (M5 x 20) heraus, mit denen
der Fuß am Bildschirm befestigt ist, und entfernen Sie den Standfuß.
Das Plasma-Fernsehgerät kann mit oder ohne Lautsprecher an der Wand befestigt werden.
2. Montieren Sie den Wandträger mit vier Wanddübeln (Ø10 x 50) und vier
Schrauben (Ø7 x 60) gemäß Abbildung 2 an der Wand.
Wählen Sie zunächst den Platz aus, an dem der Bildschirm befestigt werden soll. Rich-
ten Sie den Wandträger waagerecht an der Wand aus, und markieren Sie die beiden
Montagepunkte mit einem Bleistift. Bohren Sie die Löcher für die Kunststoffdübel, und
befestigen Sie den Wandträger mit vier Schrauben (Ø7 x 60) an der Wand.
3. Heben Sie den Plasmabildschirm an, und hängen Sie ihn mit den beiden Aufhänge-
schrauben auf der Rückseite des Bildschirms in den Löchern am Wandträger ein.
1.2 Lautsprecher
Montage der Lautsprecher (optional)
Wenden Sie den Plasmabildschirm auf die Rückseite, und stellen Sie ihn auf eine feste
Oberfläche, z.B. auf einen Tisch (Abb. 3). Stellen Sie die Lautsprecher rechts und links
neben dem Bildschirm ab.
Richten Sie die Lautsprecherhalterungen (je zwei am linken und zwei am rechten Laut-
sprecher) mit den Bohrungen am Plasmabildschirm aus, und befestigen Sie jede Hal-
terung mit vier Schrauben (M5 x 12) an Lautsprecher und Bildschirm. Schließen Sie
die Lautsprecher mit den Lautsprecherkabeln an der Plasmabox an.
ቤ
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Sonstiges
• Achten Sie darauf, daß kein helles Licht oder Sonnenschein direkt auf den Bild-
schirm fällt. Es können Spiegelungen entstehen, die die Brillanz des Bildes beein-
trächtigen.
• Der günstigste Betrachtungsabstand ist die 5–fache Bildschirmdiagonale, bei Gerä-
ten mit 107 cm Bildschirm also ca. 5,35 m.
• Antennenanschlusskabel und sonstige Bauteile zwischen der fest eingebauten
Antennen- / Breitbandsteckdose und dem Rundfunkempfänger (z. B. TV–Gerät,
Videorecorder) müssen der Euro-Norm EN 60966-2-4 entsprechen.
• In unmittelbarer Nähe des TV-Gerätes darf sich kein Magnetfeld befinden.
• Das verwendete Antennenanschlusskabel sollte ein Schirmungsmaß von mindestens
75 dB besitzen.
• Bei Verwendung nicht zugelassener Kabel und Bauteile erlischt die Betriebserlaub-
nis des Rundfunkempfängers.
1.4 Bedienelemente Plasma-Bildschirm
Vorderansicht
Rückansicht
Verbindung Plasma-
Bildschirm mit der
Tuner-Box (LVDS)
Netzkabel-Eingang
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Bedienelemente und Anschlüsse Tuner-Box
Vorderansicht
ቢ Ein- / Aus - Schalter
ባ Audioeingang Links/Rechts
ቤ Videoeingang
ቧ Lautstärke einstellen
ቨ Programmwahl P+ / P–
ቩ Menü aufrufen
ብ Kopfhörer
ቪ AV-Taste / Signalauswahl
ቦ S-VHS-Eingang
Rückansicht
A Subwoover - Ausgang
B Lautsprecher - Ausgang Links/Rechts
C Antenne
H SCART 3
I
SCART 4
J LVDS (Ausgang, z. Plasmabildschirm)
K Audio In (vom PC kommend)
D Video Out
E Video In
F SCART 1
G SCART 2
L DVI - Eingang (vom PC kommend)
M VGA - Eingang (vom PC kommend)
N Netzkabel-Eingang
voll bestückt
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Sicherheitshinweise
Bei Plasma-Displays besteht prinzi-
- brennenden Kerzen
- Gefäße mit Flüssigkeit.
Heißes Wachs und Flüssigkeiten, die ins
Geräteinnere gelangen, zerstören die elek-
trischen Bauteile Ihres TV–Gerätes. Die
elektrische Sicherheit des Gerätes ist in sol-
chen Fällen nicht mehr gewährleistet.
piell die Gefahr von Einbrenneffek-
ten. Wird über einen längeren Zeit-
raum ein stehendes Bild dargestellt
(z. B. Standbilder von TV, DVD,
Videotext oder PC), so ergeben sich
zwischen leuchtenden und nicht
leuchtenden Bildpunkten Helligkeits-
unterschiede, die sichtbar werden
können, sobald eine andere
• Gewitter sind eine Gefahr für elektrische
Geräte. Bei einem Blitzschlag in die Netz-
leitung oder die Antenne kann das Gerät
beschädigt werden, auch dann, wenn es
ausgeschaltet ist. Ziehen Sie bei Gewitter
Netzstecker und Antennenstecker aus der
Steckdose bzw. aus dem Fernsehgerät.
Darstellung erfolgt.
Um eine dauerhafte Schädigung auszuschlie-
ßen, sollten Sie unbedingt darauf achten,
dass stehende Bilder nicht dauerhaft darge-
stellt werden. Nutzen Sie nach Möglichkeit
auch Bildschirm-Schutzfunktionen bei den
angeschlossenen Geräten (z. B. PC, DVD,
Videorecorder).
• Öffnen des Gerätes und Durchführen von
Reparaturen sind dem Fachmann vorbehal-
ten.
ACHTUNG ! LEBENSGEFAHR.
Wenden Sie sich bitte bei erforderlicher
Reparatur an Ihren Fachhändler.
• Ein kaltes Gerät darf in einem warmen
Raum erst in Betrieb genommen werden,
wenn ein eventuell vorhandener
Feuchtigkeitsbeschlag verdunstet ist.
• Ihr Gerät ist für den Betrieb in trockenen
Räumen bestimmt. Sollten Sie ausnahms-
weise das Gerät im Freien betreiben, so
sorgen Sie bitte dafür, daß es vor Feuchtig-
keit (Regen, Wasserspritzer, Betauung)
geschützt ist.
• Vor dem Reinigen das Gerät mit dem Netz-
schalter ausschalten !
• Fernbedienung nicht direkt vor die Augen
halten und eine Taste drücken ! Infrarot-
Licht!
• In das Batteriefach der Fernbedienung dür-
fen keine Akkus eingelegt werden.
Es dürfen nur 2 Stück Batterien
LR03/AM4/AAA 1,5V Micro verwendet
werden.
• Fernsehgeräte benötigen eine ausreichende
Kühlung. Die Öffnungen in der Rückwand
dürfen nicht durch Gardinen, Deckchen,
Zeitungen o. ä. verdeckt werden. Die Lüf-
tungsschlitze an der Geräteunterseite müs-
sen frei zugänglich bleiben, denn darüber
saugt das Gerät die Kühlluft an.
• Der Plasma-Bildschirm ist ausschließlich für
den Empfang und die Wiedergabe von
Bild- und Tonsignalen bestimmt.
• Plasma-Bildschirm darf nur mit einer Netz-
spannung von 230 V ~ 50Hz Wechsel-
strom betrieben werden.
• Sorgen Sie für einen ausreichenden Kühl-
luftstrom, wenn Sie Ihr Gerät in einen Ein-
bauschrank stellen.
• Netzkabel so verlegen, dass keine Gegen-
stände darauf stehen oder Personen darü-
ber stolpern können!
• Stellen Sie Ihr Gerät nicht direkt neben
einer Heizung auf; die Gerätekühlung
könnte beeinträchtigt werden.
• Eingriffe dürfen nur durch Fachpersonal
durchgeführt werden.
• Auf oder über den Plasma-Bildschirm
gehören keine
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Allgemeines
Vor dem Einschalten
• Verbinden Sie den Plasma-Bildschirm und die
Tuner-Box mit dem beiliegenden LVDS-Kabel.
• Schließen Sie die Netzkabel des Plasma-Bild-
schirms und der Tuner-Box an die Steckdose an.
• Drücken Sie am Plasma-Bildschirm und der
Tuner-Box den Ein/Aus-Schalter. Die Geräte
schalten in Bereitschaft, wobei die LED’s an
beiden Geräten rot leuchten.
Einschalten
• Warten Sie ca. 5 Sek. bevor Sie den
P+
P–
Plasma-Bildschirm mit der Taste
der Fernbe-
dienung oder den P+/P– Tasten an der Tuner-
Box einschalten. Es wird immer das zuletzt
gesehene Programm eingestellt. Die LED’s an
beiden Geräten leuchten grün.
Ausschalten
Mit der Taste
der Fernbedienung in den Stand-
by Zustand schalten oder den Netzschalter am
Plasma-Bildschirm drücken.
Programmwahl
Die Programme können mit den Zifferntasten, den
„P+/P–“ Tasten auf der Fernbedienung oder der
Tuner-Box oder über die Programmtabelle ausge-
wählt werden.
P+
P–
Die Programmtabelle mit der Taste „INFO“ aufru-
fen. Mit den Cursorsteuertasten ꢀ ꢁ ꢂ ̈ den
gewünschten Sender auswählen. Programmtabelle
mit der Taste „INFO“ ausblenden.
Lautstärke einstellen
+
Mit der
werden.
Taste kann die Lautstärke verstellt
–
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
Mit der Metz Fernbedienung RL 18 können
der Plasma-Bildschirm sowie zusätzlich
Videorecorder VCR1 und VCR 2, DVD-
Player und HiFi–Geräte (z.B. Radio, Kas-
settendeck, CD-Player, Verstärker etc.) von
Metz oder verschiedenen anderen Herstel-
lern in ihren Grundfunktionen ferngesteu-
ert werden.
Die Fernbedienung übermittelt die Steuer-
befehle per Infrarotlicht zum TV–Gerät.
Die Fernbedienung muss immer zum
TV–Gerät gerichtet sein. Andere infrarot-
gesteuerte Geräte oder Systeme (z.B.
Infrarot-Kopfhörer) im Wirkungsbereich
können u.U. gestört werden.
23
ቢ
22
21
ባ
ቤ
ቶ
ት
ብ
Direkte Sonneneinstrahlung auf das
TV–Gerät kann u.U. zu Störungen
führen, weil das TV–Gerät die Infra-
rotsignale der Fernbedienung nicht
erkennt.
Um das TV–Gerät mit der Fernbedie-
nung steuern zu können, darf es nicht
mit der Netztaste ausgeschaltet sein.
ꢀ
ቴ
ታ
ቦ
ቧ
ቨ
ቲ
ቱ
ተ
Die Fernbedienung ist in den Bedienebe-
nen werkseitig wie folgt vorprogrammiert:
•TV
Metz Plasma-Bildschirm
ቯ
ቮ
ቭ
•VCR1 Metz Videorecorder mit Fernbed. RH51
•VCR2 Metz Videorecorder mit Fernbed. RF52
•DVD Metz DVD-Player mit Fernbed. RG/RH37
•HiFi Metz HiFi CD-Receiver HE 11 mit Fernbed. F11
ቩ
ቪ
ቫ
In das Batteriefach der Fernbedienung
dürfen keine Akkus eingelegt werden.
Es dürfen nur 2 Batterien vom Typ
LR03/ AM4/AAA 1,5V Micro
verwendet werden.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
zurück zum TV-Betrieb
21
Die Tastenfunktionen im
Überblick
22
Video Eingangssignal umschalten
ቢ EIN
23
Select Taste - Umschalten der Bedien-
ebene auf AV-Geräte
auf den Programmplatz vor dem Aus-
schalten
AUS (Stand-by Stellung)
ባ Bildformat auswählen
ቤ zurück zum letzten Programm
ብ Zifferntasten (direkte Programmwahl)
ቦ Cursorsteuertaste im Menü
ቧ OK Bestätigungstaste / Standbild
+
ቨ Lautstärke
–
ቩ Tonstopp
ቪ TV-Menü aufrufen
ቫ Programm –
ቭ Videotext aufrufen
ቮ Programmtabelle ein- /ausblenden
ቯ Programm +
ተ Bild im Bild (PIP) ein- /ausblenden
ቱ PIP-Bildlage verändern
ቲ Bildinhalte von PIP und Hauptbild
vertauschen
ታ PIP-Bild in Größe verändern
ቴ Split screen
(2fach Bild ein- /ausblenden)
ት Uhrzeit einblenden
ቶ Umschaltung Mono - Stereo - Zwei-
ton.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
1. Programmieren der Fernbe-
dienung zum Steuern der ein-
zelnen Geräte
Damit Ihre Unterhaltungselektronik-
Geräte ferngesteuert werden können,
muss die Fernbedienung in den einzel-
nen Bedienebenen mit einer 3stelligen
Codenummer programmiert werden.
b) Gleichzeitig die Tasten
und l–ll der
Fernbedienung so lange drücken, bis
die LED zweimal blinkt.
c) Mit den Zifferntasten den gewünsch-
ten Code (siehe Codetabelle) einge-
ben. Wird der Code angenommen, so
blinkt die LED wieder zweimal. Ist der
Code nicht vorhanden, leuchtet die
LED einmal für ca. 2 sek.
• TV (Plasma-Bildschirm)
Die TV-Bedienebene ist für den Metz
42“ Plasma-TV PIP programmiert. Eine
andere Code-Belegung ist nicht mög-
lich.
• VCR 1 (Videorecorder 1)
VCR 2 (Videorecorder 2)
1.2 Code programmieren für
CD-Player, Tuner und Tape
Nach Anwahl der Bedienschritte
a) . . . c) bleibt ein Zeitfenster von
ca. 15 sek. erhalten, danach wird
automatisch auf die TV–Bedien-
ebene zurückgeschaltet. Innerhalb
dieses Zeitfensters muss die Einga-
be erfolgen.
ꢀ
DVD-Player
HiFi (z.B. Verstärker, Tuner, Tape etc.)
Die Fernbedienung muss entsprechend
der Codeliste mit einem Code pro-
grammiert werden.
a) Wählen Sie mit der Select Taste die
Bedienebene HiFi aus. Die farbige
HiFi LED leuchtet.
Beachten Sie die werkseitigen Ein-
stellungen (S. 10) und die Code-
Liste am Ende der Bedienungsan-
leitung.
ꢀ
b) Taste
anschliessend die Taste ...
...l–ll für CD-Player (CD-Spieler)
drücken, loslassen und
1.1 Code programmieren für
VCR und DVD
...
...
für Tuner (Radio)
für Tape (Cassetten-Bandgeräte)
Ȅ
Nach Anwahl der Bedienschritte
a) . . . c) bleibt ein Zeitfenster von
ca. 15 sek. erhalten, danach wird
automatisch auf die TV–Bedien-
ebene zurückgeschaltet. Innerhalb
dieses Zeitfensters muss die Einga-
be erfolgen.
ꢀ
der Fernbedienung drücken, bis die LED
einmal blinkt.
c) Mit den Zifferntasten den gewünsch-
ten Code (siehe Codetabelle) einge-
ben. Wird der Code angenommen, so
blinkt die LED wieder zweimal. Ist der
Code nicht vorhanden, leuchtet die
LED einmal für ca. 2 sek.
a) Wählen Sie mit der Select Taste die
gewünschte Bedienebene aus. Die far-
bige LED leuchtet entsprechend der
getroffenen Auswahl.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
Wenn der Suchlauf beendet ist bzw. alle
Codenummern abgefragt wurden, blinkt
die entsprechende LED 5 mal.
1.3 Code programmieren für
HiFi–Verstärker (Amplifier)
Nach Anwahl der Bedienschritte
a) . .c) bleibt ein Zeitfenster von ca.
15 sek. erhalten, danach wird
automatisch auf die TV–Bedien-
ebene zurückgeschaltet. Innerhalb
dieses Zeitfensters muss die Einga-
be erfolgen.
ꢀ
2. Feststellen eines bereits pro-
grammierten Codes
(Auslesemodus)
Nach Anwahl der Bedienschritte
a) . . . e) bleibt ein Zeitfenster von
ca. 5 sek. erhalten, danach wird
der Auslesemodus verlassen.
Innerhalb dieses Zeitfensters muss
die Eingabe erfolgen.
ꢀ
a) Wählen Sie mit der Select Taste die
Bedienebene HiFi aus. Die farbige
HiFi LED leuchtet.
b) Taste
drücken, loslassen und
drücken
a) Um zu erfahren, welcher Code auf
einer Bedienebene programmiert ist,
verfahren Sie wie unter 1.1 a) bis b)
beschrieben ist.
anschliessend die Taste
und gedrückt halten, bis die LED zwei-
mal blinkt.
c) Taste l–ll drücken. Die LED blinkt ein-
mal
b) Geben Sie mit den Zifferntasten
ᕌᕌᕄ
ein. Die Eingabe wird mit
d) Mit den Zifferntasten den gewünsch-
ten Code (siehe Codetabelle) einge-
ben. Wird der Code angenommen, so
blinkt die LED wieder zweimal. Ist der
Code nicht vorhanden, leuchtet die
LED einmal für ca. 2 sek.
zweimaligem Blinken quittiert.
ᕃ
c) Zifferntaste
(für die erste Ziffer der
Codenummer) drücken. Die Anzahl
der Blinkimpulse steht für die pro-
grammierte Zahl (z.B. LED blinkt 3 mal
- Ziffer 3 ist programmiert).
ᕄ
1.4 Suchlauf
d) Zifferntaste
(für die zweite Ziffer
der Codenummer) drücken. Die
Anzahl der Blinkimpulse steht für die
programmierte Zahl (z.B. LED blinkt
nicht - Ziffer 0 ist programmiert).
ᕅ
Nach Anleitung Code programmieren
für ... VCR, DVD, CD, Tuner, Tape vorge-
hen bis zur Eingabe der Codenummer.
Als 3stellige Codenummer "001" für
Suchlauf eingeben. Die Eingabe wird mit
2 x LED-Blinken quittiert. Suchlauftaste
(je nach Bedienebene, siehe Tabelle Seite
14 und 15) gedrückt halten bis externes
Gerät stoppt bzw. abschaltet (alle 1,5
sec wird automatisch ein AUS bzw.
STOP-Befehl gesendet).
e) Zifferntaste
(für die dritte Ziffer der
Codenummer) drücken. Die Anzahl
der Blinkimpulse steht für die pro-
grammierte Zahl (z.B. LED blinkt 7
mal - Ziffer 7 ist programmiert).
Der ausgelesene Code wäre
ᕅ ᕌ ꢀ
somit
Suchlauftaste loslassen, mit Select-Taste
bestätigen (gefundener Code wird
gespeichert).
Sollten Sie sich beim Auslesen verzählt
haben, so beginnen Sie wieder mit Pkt.
2c).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
Taste
V C R 1 / 2
23
ቢ
ቢ
Ein
Ein / Stand-by
22
21
ባ
ቤ
ብ
Aufnahme
Zeitanzeige im Display
ባ
ቤ
0...9 Zifferntasten: Programmwahl
ꢀ ꢁ
ቶ
ት
Programm +/–
ቦ
ꢂ ̈
OK
Vorlauf / Rücklauf
OK
ቧ
ቨ
ቩ
ቪ
ቫ
ቭ
ቮ
ቯ
ተ
ቱ
ቲ
ታ
ቴ
ት
ቶ
Vol.+/–
Mute
Menu
P-
Lautstärke +/– TV
Stummschaltung TV
MENU
ብ
Schaltspannung Ein/Aus
Text
Info
Programmtabelle aufrufen
P+
Pause
STOP / Suchlauf
PLAY
ቴ
ታ
ቦ
ቧ
ቨ
rot
grün
weiß
gelb
blau
Zeitlupe
ቲ
ቱ
ተ
Ȅ
I-II
k
21
TV
AV
k
22
AV - Eingang
ቯ
ቮ
ቭ
k
23
Select
Auswahl Bedienebene
ቩ
ቪ
Hinweis:
ቫ
Die Zuordnung der Fernbedienungstasten zu den
Gerätefunktionen gilt für die werkseitig eingestell-
ten AV-Geräte. Bei Verwendung anderer
AV–Geräte gemäß Code-Tabelle, können sich
Abweichungen bzw. Einschränkungen ergeben.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Die Fernbedienung
H i F i
Taste
D V D
C D ( I-II )
T U N E R ( Ȅ )
T A P E (
)
EIN: Display Time/Track EIN: Radiotext ein/aus
EIN & AV, EIN:ein/standby Ein & AV, Ein: ein/standby
ቢ
Ein
Ein / Stand-by
ባ
ቤ
ብ
Return
Angle
I-II & EIN: CD
I-II & EIN: CD
0...9
ꢀ ꢁ
ꢂ ̈
Zifferntasten: Titelwahl
Cursor auf/ab
Cursor links/rechts
OK / Enter
Zifferntasten: Titelwahl Zifferntasten: Progr.wahl
Titel +/–
Programm +/–
Frequenz +/–
ቦ
ቧ
ቨ
ቩ
ቪ
ቫ
ቭ
ቮ
ቯ
ተ
ቱ
ቲ
ታ
ቴ
ት
ቶ
OK
Vol.+/–
Mute
Menu
P-
Lautstärke +/– TV
Stummschaltung TV
MENU
Lautstärke +/– AMP
Lautstärke +/– AMP
Lautstärke +/– AMP
Title
Text
Display
Info
P+
Pause
STOP / Suchlauf
PLAY
Pause
rot
STOP / OPEN-CLOSE / Suchlauf Zifferntaste ባ=Suchlauf
Suchlauf
grün
weiß
gelb
blau
PLAY
EJECT
Skip +
Skip –
Audio
Ȅ & EIN: Tuner
Ȅ & EIN: Tuner
Ȅ
I-II
Subtitle
& EIN: Tape-Eingang
& EIN: Tape-Eingang
AUX Eingang
k
21
TV
AV
k
22
Repeat
AUX Eingang
AUX Eingang
k
23
Select
Auswahl Bedienebene
Auswahl Bedienebene Auswahl Bedienebene Auswahl Bedienebene
Suchlauf:
Nach Anleitung Code programmieren für ... VCR, DVD, CD, Tuner, Tape vorgehen bis zur Eingabe
der Codenummer. Als 3stellige Codenummer "001" für Suchlauf eingeben. Die Eingabe wird mit
2 x LED-Blinken quittiert. Suchlauftaste (je nach Bedienebene, siehe Tabelle) gedrückt halten bis
Gerät stoppt bzw. abschaltet (alle 1,5 sec wird automatisch ein AUS bzw. STOP-Befehl gesendet).
Suchlauftaste loslassen, mit Select-Taste betätigen (gefundener Code wird gespeichert).
Reset:
Nach Anleitung Code programmiern für ... VCR, DVD, CD, Tuner, Tape und vorgehen bis zur
Eingabe der Codenummer. Als 3-stellige Codenummer "000" für Reset eingeben. Die Eingabe wird
mit 2 x LED-Blinken quittiert. Jetzt sind wieder alle werkseitig eingestellten Codes (Auslieferzustand)
eingestellt.
Reset wird für alle Bedienebenen gleichzeitig durchgeführt, unabhängig in welcher Bedienebene der
Reset-Befehl ausgelöst wurde.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Betrieb ohne Fernbedienung
Diese Betriebsart ist nur als Notbedienung
gedacht, wenn die Batterien Ihrer Fernbedienung
leer sind oder die Fernbedienung nicht zur Hand
sein sollte.
Die Ortsbedienung finden Sie an der
Vorderseite der Tuner-Box.
ꢀ
Einschalten
ቢ
Netztaste
der Tuner-Box drücken - der Stand-
by Betrieb ist eingeschaltet. Schalten Sie auch den
Plasma-Bildschirm mit der Netztaste ein. Die LED’s
leuchten rot. Drücken Sie dann die „P+“ oder „P–“
ቤ
Tasten
zum Einschalten. Die LED’s leuchten grün.
Lautstärke:
ባ
Drücken Sie die Taste
Programmwahl:
ቤ
„z +“ oder „z –“
Tasten
„
P+“ oder „P–“drücken.
Menü:
ብ
Drücken Sie die Taste
die Tasten „P+“ , „P–“ ,
verwenden.
„M“. Zur Menüsteuerung
z
„
+“ und „Volume –“
TV/AV:
ቦ
Die Taste „AV“
dient zum Umschalten von
TV–Betrieb auf AV-Betrieb.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Land einstellen
Menü aufrufen
Land einstellen
Nach dem Aufstellen muss der Aufstellort bzw.
das Land (z.B. Deutschland) eingegeben werden.
Damit wird dem Gerät eine Grundeinstellung (z.B.
Kanalraster etc.) zugewiesen.
• TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das Menü „Einstel-
lungen“ anwählen.
MENU
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„TV-Tuner“ anwählen und mit Taste „OK“ öff-
nen.
• Mit der Cursorsteuertaste ꢂ ̈ das Untermenü
„APS“ anwählen.
OK
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„Land“ anwählen.
• Mit der Cursorsteuertaste ꢂ ̈ das
gewünschte Land, entsprechend der
Auswahl, einstellen.
APS
• TV-Menü mit der Taste „TV“ aus-
blenden.
Land
Deutschland
Die Einstellung wird mit dem
Verlassen des TV-Menüs auto-
matisch gespeichert.
ꢀ
Mit <Rechts / Links> Land ändern
TV
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
5.1 Sprache einstellen
Sprachwahl im TV-Menü
Dem TV-Menü kann eine Sprache entsprechend
der angebotenen Auswahl zugeteilt werden. Alle
Texte im Menü und in der Bedienhilfe (Informa-
tion) werden in der gewählten Sprache angezeigt.
Sprache einstellen:
• TV-Menü mit der Taste „MENU“ aufrufen.
MENU
OK
• Mit der Cursorsteuertaste ̈ das Menü „Optio-
nen“ anwählen.
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„Sprache“ anwählen.
• Mit der Cursorsteuertaste ꢂ ̈ die gewünschte
Sprache, entsprechend der Auswahl, einstellen.
• TV-Menü mit der Taste „TV“ aus-
blenden.
Optionen
Die Einstellung wird mit dem
Verlassen des TV-Menüs auto-
matisch gespeichert.
ꢀ
Sprache
deutsch
Bildschirmanzeige Zeitli.
Menühintergrund
Scart 2-Ausgang
Scart 4-Ausgang
Sleeptimer
verbleibende Zeit
Mit <Rechts / Links> Sprache ändern
TV
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Sender einstellen
Menü aufrufen
Fernsehsender können auf drei verschiedene
Arten eingestellt werden:
a) Automatische Sendersuche (APS)
Bei der Automatischen Sendersuche wird der gesamte
Empfangsbereich automatisch durchsucht. Die gefunde-
nen Sender werden in einer Sendertabelle abgelegt, die
am Ende des Suchvorgangs präsentiert wird. Wenn Sie
mit der Reihenfolge der gefundenen Sender nicht zufrie-
den sind, können die Sender noch verschoben oder
gelöscht werden, siehe Kapitel „6.2. Sender sortieren“.
Automatische Sendersuche durchführen
MENU
•
TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das Menü „Einstel-
lungen“ anwählen.
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„TV-Tuner“ anwählen.
OK
• Taste „OK“ drücken.
• Mit der Cursorsteuertaste ̈ das Untermenü
„APS“ öffnen.
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „Auto. Einstellen“
anwählen.
APS
• Taste „OK“ drücken. Die Einblend-
box fragt nun, ob Sie den Suchlauf
wirklich starten möchten.
Auto. Einstellungen
Mit <OK> aktivieren
• Nochmals Taste „OK“ drücken und
den Suchlauf starten.
• Eine Sendertabelle wird, entspre-
chend der gefundenen Sender,
angezeigt.
Mit <OK> APS starten
• In der Sendertabelle können nicht gewünschte
Sender mit der Cursorsteuertaste angesteuert
und mit der roten Taste gelöscht werden.
Die Einstellung wird mit dem Verlassen des
TV-Menüs automatisch gespeichert.
ꢀ
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
6. Sender einstellen
b) Manuelle Suche
Mit dem manuellen Suchlauf können einzelne Sen-
der mit unbekanntem Kanal bzw. unbekannter
Frequenz gesucht werden.
Manuelle Suche durchführen
•
TV-Menü mit der Taste „MENU“ aufrufen.
MENU
OK
• Mit der Cursorsteuertaste ̈ das Menü
„Einstellung“ anwählen.
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„TV-Tuner“ anwählen.
• Taste „OK“ drücken und Untermenü „Program-
mieren“ öffnen.
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„Manuelle Suche“ anwählen.
• Mit der Cursorsteuertaste ̈ den
Suchlauf Starten.
Programmieren
• Wenn ein Sender gefunden wird,
bleibt der Suchlauf stehen.
•
Wenn der gefundene Sender gespei-
chert werden soll, dann wählen Sie
mit der Cursorsteuertaste ꢀ den
Menüpunkt „Programm speichern“.
Manuelle Suche
• Mit der Cursorsteuertaste ꢂ ̈ das
gefundene Programm speichern.
Mit <Rechts / Links> Kanalsuche starten
• TV-Menü mit der Taste „TV“ ausblenden.
TV
Das Senderlogo kann geändert werden,
siehe Kap. 6.1.
ꢀ
20
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Sender einstellen
Menü aufrufen
c) Direkte Kanaleingabe
Die direkte Kanaleingabe bietet die Möglichkeit,
einen Sender direkt zu programmieren. Bei dieser
Art der Sendereinstellung muss die Kanalnummer
des Senders bekannt sein.
MENU
Direkte Kanaleingabe durchführen
•
TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das Menü „Einstel-
lungen“ anwählen.
OK
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„TV-Tuner“ anwählen.
• Taste „OK“ drücken und Unterme-
nü „Programmieren“ öffnen.
Programmieren
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „Kanaltyp“ anwählen.
• Mit der Cursorsteuertaste ̈ den
gewünschten Kanaltyp (C = Nor-
malkanal / S = Sonderkanal) ein-
stellen.
Kanal
Kanaltyp
C
S
• Mit der Cursorsteuertaste ꢀ den
Menüpunkt „Kanal“ anwählen und
mit den Zifferntasten die Kanal-
nummer eingeben.
<Rechts / Links> Kanal ändern
• Wenn der gefundene Sender gespeichert wer-
den soll, dann wählen Sie mit der Cursorsteuer-
taste ꢁ den Menüpunkt „Programm speichern“.
• Mit den Cursorsteuertasten ꢂ ̈ das gefundene
Programm speichern.
TV
• TV-Menü mit der Taste „TV“ ausblenden.
Das Senderlogo kann geändert werden,
siehe Kap. 6.1.
ꢀ
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
6. Sender einstellen
Feinabstimmung (Frequenz)
Bei der Sendereinstellung werden die einzelnen
Sender auf Kanalmitte abgestimmt. In der Regel
reicht diese Abstimmung aus. Sollte diese Automa-
tik zu keinem befriedigenden Ergebnis führen,
kann eine Feinabstimmung durchgeführt werden.
MENU
Feinabstimmung durchführen
• Den Programmplatz einstellen, der abgestimmt
werden soll.
OK
•
TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das
Menü „Einstellungen“ anwählen.
Programmieren
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „TV-Tuner“ anwählen.
Feinabstimmung
• Taste „OK“ drücken und Untermenü
„Programmieren“ öffnen.
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „Feinabstimmung“
anwählen.
• Mit den Cursorsteuertasten ꢂ ̈
eine Feinabstimmung vornehmen.
<Rechts / Links> Feinabstimmung
• Wenn die Feinabstimmung gespeichert werden
soll, dann wählen Sie mit der Cursorsteuertaste
ꢁ den Menüpunkt „Programm speichern“.
TV
• Mit den Cursorsteuertasten ꢂ ̈ die Feinabstim-
mung speichern.
• TV-Menü mit der Taste „TV“ ausblenden.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 Sender-Logo
Menü aufrufen
Jedem Sender wird über das VPS-Signal ein Sen-
derlogo mit max. 4 Stellen automatisch zugewie-
sen. Wenn diese Automatik nicht funktioniert oder
Sie ein anderes Logo möchten, kann es manuell
geschrieben werden.
Sender-Logo einstellen
INFO
• Den gewünschten Programmplatz einstellen.
• Taste „INFO“ drücken.
• Gelbe Taste drücken und den Änderungsmode
aufrufen.
• Das Senderlogo kann mit der Taste „AV“ kom-
plett gelöscht werden.
• Mit den Cursorsteuertasten ꢂ ̈ können Sie die
einzelnen Stellen anwählen und mit den Cursor-
steuertasten ꢁ ꢀ die Buchstaben bzw. Ziffern
ändern.
OK
• TV-Menü mit der Taste „TV“ ausblenden.
Die Einstellung wird mit dem Verlassen des
TV-Menüs automatisch gespeichert.
ꢀ
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
6.2 Sender sortieren
In der Sendertabelle können einzelne Sender ver-
schoben oder gelöscht werden.
Sender verschieben, löschen
•
Mit der Taste „INFO“ die Programmtabelle aufru-
fen.
INFO
• Mit den Cursorsteuertasten ꢂ ̈ ꢀ ꢁ den Sen-
der ansteuern, der verschoben oder gelöscht
werden soll.
• Zum Löschen die rote Taste drücken und im
Menü die Sicherheitsabfrage mit „OK“ bestäti-
gen.
OK
• Zum Verschieben die grüne Taste
drücken, das vorher rot umrahmte
Senderlogo wird gelb umrahmt und
quasi zum „ausschneiden“ bereitge-
stellt.
Programmtabelle
• Mit den Cursorsteuertasten ꢂ ̈ ꢀ
ꢁ das gelb umrahmte Senderlogo
an den neuen Platz verschieben
• Die grüne Taste drücken und der
Sender wird am markierten Platz
eingefügt.
Löschen
Einfügen
Name
Alle anderen Programmplätze werden ent-
sprechend verschoben !
• „Programmtabelle“ mit der Taste „TV“ ausblen-
den.
ꢀ
TV
24
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Programmwahl
Programmwahl u. Programmplatzver-
waltung
Der Plasma-Bildschirm kann max. 100 Programm-
plätze (0-99) in der Sendertabelle verwalten. Die-
se Programmplätze können Sie mit den Ziffernta-
sten, den „P+/P–“ Tasten oder über die
Programmtabelle anwählen.
Nach dem Drücken einer Zifferntaste haben Sie
ein Zeitfenster von 3 Sek. um weitere Zifferntasten
zu drücken.
P+
P–
Programmwahl über die
Programmtabelle
Im normalen Fernsehbetrieb kann die Programm-
tabelle mit der Taste „INFO“ aufgerufen werden.
In der eingeblendeten Tabelle können die Pro-
gramme mit den Cursorsteuertasten ꢂ ̈ ꢀ ꢁ
angesteuert werden. Das angesteuerte Programm
wird eingeblendet.
INFO
OK
Zurück zum letzten Programm
Mit der Taste
kann zwischen den zwei zuletzt
gewählten Programmplätzen hin- und hergeschal-
ten werden.
Beispiel:
Sie sehen das Programm RTL. Während der Wer-
bung schalten Sie mit den Zifferntasten auf das
Programm ARD.
Mit der Taste
kann nun zwischen diesen beiden
Programmen hin- und hergeschalten werden.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
8. Bildeinstellungen
Die Bildeinstellungen (Helligkeit, Kontrast, Schärfe
etc.) können generell für alle Programme eingestellt
werden.
Bildeinstellungen aufrufen:
•
TV-Menü mit der Taste „MENU“ aufrufen.
MENU
• Mit der Cursorsteuertaste ̈ das Menü „Bild“
anwählen.
• Mit der Cursorsteuertaste ꢁ den gewünschten
Menüpunkt „Helligkeit“, „Kontrast“, „Schärfe“
oder „Farbe“ anwählen.
• Mit den Cursorsteuertasten ꢂ ̈ können die ein-
zelnen Bildeinstellungen verändert werden.
OK
• TV-Menü mit der Taste „TV“ ausblenden.
Die Einstellung wird mit dem
Verlassen des TV-Menüs auto-
matisch gespeichert.
ꢀ
Bild
Helligkeit
<Rechts / Links> Helligkeit einstellen
TV
26
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Audio / Toneinstellungen
Menü aufrufen
Die Toneinstellungen (Lautstärke, Kopfhörer-Laut-
stärke, Balance usw.) können im Menü „Audio“
eingestellt werden.
Audioeinstellungen aufrufen:
• TV-Menü mit der Taste „MENU“ aufrufen.
MENU
• Mit der Cursorsteuertaste ̈ das Menü „Audio“
anwählen.
• Mit der Cursorsteuertaste ꢁ den gewünschten
Menüpunkt „Lautstärke“, „Kopfhörer-Lautstärke“,
„Kopfhörer-Tonmodus“, „Balance“, „Subwoofer“
oder „Equalizer“ anwählen.
OK
• Mit den Cursorsteuertasten ꢂ ̈ können die ein-
zelnen Audioeinstellungen verän-
dert werden.
• TV-Menü mit der Taste „MENU“
ausblenden.
Audio
Die Einstellung wird mit dem
Verlassen des TV-Menüs auto-
matisch gespeichert.
ꢀ
Subwoofer
AUS
Subwoofer
An der Rückseite der Tuner-Box kön-
nen Sie einen aktiven Subwoofer zur
Optimierung der Basswiedergabe
anschliesen. Schalten Sie nach
<Abwärts> für Audioeinstellungen
Anschluss eines Subwoofers den Menüpunkt EIN.
Equalizer (Tonmodus) Einstellungen:
Für den Equalizer gibt es die Standardeinstellun-
gen „Normal“, „POP“, „Rock“, „Jazz“ und
„Klassik“.
Wenn Sie mit den Standardeinstellungen nicht
zufrieden sind, können Sie unter „Benutzer“ Ihre
persönliche Einstellung konfigurieren.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Sonderfunktionen
Bild im Bild (PIP)
Menü aufrufen
Das PIP-Bild kann für ein anderes TV-Programm
oder die Einblendung eines AV-Gerätes genutzt
werden.
Bild im Bild (PIP) ein- / ausblenden:
• Drücken Sie die rote Taste. Das PIP-Bild wird
eingeblendet.
• Mit den Cursorsteuertasten ꢀ ꢁ können die
Bildinhalte selektiert werden. Der selektierte Bild-
inhalt ist mit einem grünen Rahmen gekenn-
zeichnet.
OK
• Mit den Zifferntasten oder den „P+/P–“ Tasten
kann im selektierten Bild ein anderer Programm-
platz eingestellt werden.
• Durch mehrmaliges Drücken der
Taste „AV“ kann im selektierten
Bild ein AV-Programm (z.B. Video-
rec. oder Camera usw.) eingestellt
werden.
•
Das eingeblendete PIP-Bild kann in
8 Stufen gezoomt werden, dazu
die gelbe Taste drücken und
anschließend mit den Cursorsteuer-
tasten ꢂ ̈ das PIP-Bild vergrößern
oder verkleinern.
•
Das eingeblendete PIP-Bild kann in
seiner Position verändert werden,
dazu die grüne Taste drücken und
danach mit den Cursorsteuertasten
ꢂ ̈ das PIP-Bild verschieben.
• Mit der weißen Taste können die Bildinhalte ver-
tauscht werden.
• Rote Taste drücken und das PIP-Bild wird ausge-
blendet.
Die Einstellungen werden mit dem Ausblen-
den des PIP-Bildes automatisch gespeichert.
ꢀ
28
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Sonderfunktionen
Bildgröße
Funktion aufrufen
Mit der Funktion „Bildgröße“ können Sendungen
der verschiedenen Formate an das Breitbildformat
des Bildschirms angepasst werden. Das Bild wird je
nach Einstellung linear oder nicht linear gezoomt.
Bildformat aufrufen:
• Die Taste
drücken, am unteren Bildschirm-
OK
rand erscheint die Einblendung für das einge-
stellte Bildformat.
• Mit den Cursorsteuertasten ꢂ ̈ kann nun die
Einstellung ausgewählt werden.
oder über das Menü „Fenster“
Auswahlmöglichkeiten Bildformat:
Normal:
Die Sendungen werden im Standardformat 4:3
wiedergegeben.
Auto: (bevorzugte Einstellung)
Der Bildinhalt wird entsprechend des Eingangssignales (4:3 oder 16:9) formatrichtig
wiedergegeben. Bei TV wird das WSS-Signal ausgewertet, wird vom Sender kein
WSS-Signal gesendet wird das Bild wie in der Einstellung "Ausfüllen" dargestellt.
Ausfüllen:
Bildschirmfläche wird formatunabhängig immer horizontal ausgefüllt.
16:9
Bildsignale im 16:9 Format werden soweit vergrößert, dass der Bildschirm vertikal
vollständig ausgeschrieben wird, an den Seiten bleiben dann nur noch schmale
schwarze Streifen.
Tipp: Sendungen im 4:3 Format können mit dieser Einstellung vergrößert dargestellt
werden, es wird lediglich am oberen und unteren Bildrand ein geringer Teil des Bil-
dinhaltes abgeschnitten.
Letterbox:
Wenn eine Sendung oben und unten einen schwarzen Streifen hat, können diese aus-
geblendet werden.
Untertitel:
Das Bild wird gezoomt und nach oben geschoben, damit der Untertitel gut lesbar
erscheint.
Die Einstellung wird mit dem Verlassen des TV-Menüs automatisch gespeichert.
ꢀ
29
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Sonderfunktionen
Split Screen
Bei der „Split Screen“ Darstellung wird der Bild-
schirm in zwei gleichgroße Hälften geteilt.
Der geteilte Bildschirm kann mit der Taste
und ausgeschaltet werden.
ein-
Der Ton wird nach dem Aufrufen der
Funktion prinzipiell von der Sendung auf
der linken Seite wiedergegeben.
Mit den Cursorsteuertasten ꢀ ꢁ können
die Bilder selektiert werden. Ein selektier-
tes Bild wird kurzzeitig mit einem grünen
Rahmen versehen. Nun kann das Pro-
gramm mit den Zifferntasten, den
„P+/P–“ Tasten oder der „AV“ Taste
umgeschaltet werden. Ebenso können Sie
Bildeinstellungen (siehe Kap. 8) vorneh-
men.
Der Ton wird vom selektierten Bild wiedergegeben.
Wird die Funktion mit der Taste
ausgeschaltet,
so schaltet der Plasma-Bildschirm immer auf die
Sendung, die in der linken Bildhälfte dargestellt
wird um.
Die Einstellung wird mit dem Verlassen der
Funktion automatisch gespeichert.
ꢀ
10. Sonderfunktionen
Standbild
Nach Drücken der Taste „OK“ wird das Bild sofort
eingefroren und am Bildschirm angezeigt. Die Sen-
dung (oder Videofilm) läuft jedoch im Hintergrund
weiter.
OK
Nach dem wiederholten Drücken der Taste wird
wieder auf die laufende Sendung (oder Videofilm)
umgeschaltet.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Sonderfunktionen
Sleep Timer
Menü aufrufen
Mit der Programmierung des Sleeptimers können
Sie festlegen, wann der Plasma-Bildschirm automa-
tisch ausschaltet.
MENU
Der Sleeptimer kann auf Aus, 30, 60, 90 oder
120 Minuten eingestellt werden.
OK
Sleeptimer einstellen:
•
TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das
Menü „Optionen“ anwählen.
Optionen
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „Sleeptimer“ anwählen.
Sprache
Bildschirmanzeige Zeitli.
Menühintergrund
Scart 2-Ausgang
• Mit den Cursorsteuertasten ꢂ ̈ die
gewünschte Zeit einstellen, nach der
das TV–Gerät automatisch ausge-
schaltet wird.
Scart 3
FAV
Schlafzeit einstellen
30 minuten
Scart 4-Ausgang
Sleeptimer
verbleibende Zeit
• TV-Menü mit der Taste „TV“ aus-
blenden.
Sleeptimer einstellen
Die Einstellung wird mit dem
Verlassen des TV-Menüs automatisch gespei-
chert.
ꢀ
TV
10. Sonderfunktionen
Uhrzeit einblenden
Die Uhrzeit kann mit der Taste
werden, wenn Sie einen Sender eingestellt haben,
der Videotext ausstrahlt.
eingeblendet
Ȅ
Ȅ
Auf Programmplätzen, die keinen Videotext aus-
strahlen, kann keine Uhrzeit eingeblendet werden.
Die Uhrzeit wird nach ca. 4 Sekunden automatisch
ausgeblendet.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
11. Videotext
Der Videotext ist ein zusätzlicher, kostenloser
Infoservice der Sendeanstalten. In dieser
elektronischen Zeitung kann auf verschiedene
Arten geblättert werden.
i
Videotext aufrufen:
• Taste „TEXT“ drücken.
Am Bildschirm erscheint die Seite 100 (Inhalts-
verzeichnis) des Videotextes.
TEXT
Videotext steuern bei angezeigten Seiten:
• Mit der blauen Taste kann im Videotext die The-
menauswahl durchgeblättert werden.
• Mit der gelben Taste kann im Videotext die
Kapitelauswahl durchgeblättert werden.
• Mit der roten Taste können die Videotextseiten
rückwärts geblättert werden.
• Mit der grünen Taste können die Videotextseiten
vorwärts geblättert werden.
Wenn bestimmte Seiten angesteuert werden sol-
len, geben Sie die Seitennummer mit den Ziffern-
tasten ein.
Unterseiten werden automatisch weitergeblättert.
Videotext ausblenden:
• Taste „TV“ oder „TEXT“ drücken.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Kopfhörer anschließen
Der Kopfhöreranschluss befindet sich an der
Vorderseite der Tuner-Box.
Wir empfehlen Kopfhörer mit einer Impedanz von
nicht weniger als 32 Ω. Bei Kopfhörer mit kleine-
rer Impedanz (ca. 8 Ω), verringert sich der Aus-
steuerbereich.
Bei 2-Ton-Sendungen kann, unabhängig von den
Gerätelautsprechern, Ton 1 oder Ton 2 über den
Kopfhörer wiedergegeben werden.
Kopfhörertoneinstellungen können im Audio-Menü
(siehe Kap. 9 ) vorgenommen werden.
Kopfhöreranschluss
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Menü aufrufen
13. AV Geräte
AV-Geräte (Audio/Video) sind Zusatzgeräte, die Bild-
oder/und Tonsignale ausgeben (z.B. Videorecorder,
DVD-Player, Decoder, Videokamera etc.) und an ein
TV–Gerät angeschlossen werden können.
AV
Videorecorder, DVD-Player usw. können an der
Scart 1- oder Scart 2-Buchse angeschlossen wer-
den. Decoder müssen an der Scart 1-Buchse ange-
schlossen werden.
oder
MENU
Wenn die AV-Geräte an den Scart-Buchsen auf
Wiedergabe (FBAS-Signal) geschaltet werden, so
schaltet der Plasma-Bildschirm automatisch in den
AV–Modus, wenn das AV-Gerät eine Schaltspan-
nung ausgibt.
OK
Wenn AV-Geräte an den Front-Buchsen ange-
schlossen sind, muss bei Wiedergabe im TV–Gerät
manuell in den AV–Modus geschaltet
werden.
Einstellungen
AV-Modus manuell einstellen
• Die Taste „AV“ mehrmals drücken
Quelle Auswahl
und die AV-Programmplätze wer-
Scart 1
den der Reihe nach durchgeschaltet
Scart 1 RGB
Scart 2
Scart 2 RGB
Scart 3
Scart 4
BAV
- oder -
•
TV-Menü mit der Taste „MENU“ aufru-
fen.
PC
<OK> aktiviert Auswahl der Signalquelle
• Mit der Cursorsteuertaste ̈ das
Menü „Einstellungen“ anwählen.
• Mit der Cursorsteuertaste ꢁ den Menüpunkt
„Quelle Auswahl“ anwählen.
• Taste „OK“ drücken und Untermenü „Quelle Aus-
wahl“ öffnen.
• Mit den Cursorsteuertasten ꢁ ꢀ die Quelle bzw.
Anschlussbuchse anwählen, die für das
gewünschte AV-Gerät notwendig ist.
• Mit der Cursorsteuertaste ̈ die Einstellung der
Quelle bzw. Anschlussbuchse aktivieren.
• AV-Gerät im entsprechenden Modus starten.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV Geräte
Auswahlmöglichkeiten
• Tuner
Der vom Plasma-Bildschirm empfangene Sender
wird am Bildschirm gezeigt.
• Scart 1/2/3/4
Das Bild vom AV-Gerät, welches an der jeweili-
gen Scart–Buchse angeschlossen ist, wird im For-
mat FBAS gezeigt.
• Scart 1/2 RGB
Das Bild vom AV-Gerät, welches an
der jeweiligen Scart–Buchse
angeschlossen ist, wird im Format
RGB gezeigt.
Fenster
• PC und DVI
Hinweis: Dieses Menü erscheint nur
Das Bild vom angeschlossenen PC
wird angezeigt.
bei Anschluss über PC oder DVI.
Im Menü „Fenster“ können Bildgrö-
ße und Bildlage eingestellt werden.
<Abwärts> Größeneinstellungen
Im Menü „Bild“ können Helligkeit,
Kontrast und Phase (Bildabgleich für
die Bildschärfe, wird bei Anschluss
an den PC automatisch vorgenom-
men) eingestellt werden.
Bild
• BAV (Back-AV-Buchse, In/Out) an
der Rückseite der Tuner-Box
Hinweis: Dieses Menü erscheint nur
• FAV (Front-AV-Buchse)
bei Anschluss über PC oder DVI.
Das Bild vom AV-Gerät, welches an
der Front–Buchse angeschlossen ist,
wird im FBAS–Bildsignal gezeigt.
<Abwärts> Bildeinstellungen für aktuel. Fenster
• S-Video
Das Bild vom AV-Gerät, welches an der
Front–Buchse angeschlossen ist, wird im
S–Video–Bildsignal (YC) gezeigt.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV Geräte Überspielen
Menü aufrufen
Der Plasma-Bildschirm hat einen Überspiel- oder
Kopiermodus, d.h., das an der Scart 2-Buchse
angeschlossene Aufnahmegerät kann das Bild auf-
zeichnen, welches vom Abspielgerät an der „FAV“
(Front-AV-Buchse), von der Scart 1-Buchse oder
dem Tuner geliefert wird.
MENU
Scart 2-Ausgang einstellen:
OK
•
TV-Menü mit der Taste „MENU“ aufrufen.
• Mit der Cursorsteuertaste ̈ das Menü „Optio-
nen“ anwählen.
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „Scart 2-Ausgang“
anwählen.
Optionen
• Mit den Cursorsteuertasten ꢂ ̈ die
Buchse auswählen, an der das
gewünschte Abspielgerät ange-
Sprache
Bildschirmanzeige Zeitli.
Menühintergrund
Scart 2-Ausgang
Scart 4-Ausgang
Scart 3
schlossen ist.
FAV
• Am Aufnahmegerät eine Aufnahme
Sleeptimer
starten und am Abspielgerät auf
„Play“ drücken.
<Rechts / Links> Scart 2-Ausgang auswählen
• TV-Menü mit der Taste „TV“ aus-
blenden.
TV
Die Einstellung wird mit dem Verlassen des
TV-Menüs automatisch gespeichert.
ꢀ
36
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV Geräte
Menü aufrufen
Bildqualität bei Bildeinspielung von
Bandgeräten
MENU
Die VCR-Funktion sorgt bei Bildeinspielungen von
Bandgeräten z.B. Camcorder oder Videorecordern
für eine optimale Bildqualität.
Die VCR-Funktion im Menü „Optionen“ ist
nur anwählbar, wenn z. B. der angeschlosse-
ne Videorecorder ein Signal liefert.
ꢀ
OK
VCR-Funktion einstellen
• Wiedergabe am AV-Gerät starten.
•
TV-Menü mit der Taste „MENU“ aufru-
fen.
Optionen
• Mit der Cursorsteuertaste ̈ das
Menü „Optionen“ anwählen.
Sprache
vcr
EIN
Bildschirmanzeige Zeitli.
Menühintergrund
Scart 2-Ausgang
Scart 4-Ausgang
Sleeptimer
• Mit der Cursorsteuertaste ꢁ den
Menüpunkt „vcr“ anwählen
Scart 3
FAV
• Mit den Cursorsteuertasten ꢂ ̈
kann die Funktion ein- und ausge-
schaltet werden.
• TV-Menü mit der Taste „MENU“
ausblenden.
30 minuten
verbleibende Zeit
Mit <Rechts / Links> VCR ein- und ausschalten
Die Einstellung wird mit dem Verlassen des
TV-Menüs automatisch gespeichert.
ꢀ
37
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV Geräte - PC
Anschluss des PC über den VGA-Eingang
Schalten Sie Computer und TV-Gerät aus, bevor
Sie die Anschlüsse vornehmen.
Schließen Sie das VGA-Kabel an den VGA-Ein-
gang Ihres TV-Geräts und an die 15-polige Buchse
an der Rückseite Ihres Computers an.
Ziehen Sie die Schrauben an den Steckern fest, bis
die Anschlüsse fest verbunden sind.
Wenn Sie ein Windows-Betriebssystem auf einem
PC mit einer Microsoft Plug&Play-kompatiblen Gra-
fikkarte verwenden, wählt Ihr System automatisch
die beste Bildwiederholrate für Ihren Monitor aus.
Anschluss des PC über den DVI-Eingang
(Digital Video Interface)
Um die bestmögliche Bildqualität zu erzielen, müs-
sen Sie die DVI-Buchsen am TV-Gerät und an
Ihrem PC verwenden. Dadurch kann der PC ein
rein digitales Signal von der Grafikkarte direkt an
das TFT-TV-Gerät senden. Da an dem TFT-TV-Gerät
eine DVI-I-Buchse vorhanden ist, sollten Sie ein
DVI-D- oder DVI-I-Kabel für den Anschluss verwen-
den.
Es werden DDC (Display Data Channel) und EDID
(Extended Display Identification Data), die für die
Plug & Play-Kompatibilität verwendet werden,
unterstützt.
Hot-Plug-Detektion wird nicht unterstützt.
Niedrige Bildwiederholraten wie 60Hz oder 72Hz
sollten verwendet werden. Auch sollte die native
Auflösung vorgezogen werden.
Die DVI-Schnittstelle unterstützt kein HDCP (High
Bandwidth Digital Content Protection), daher kann
kein HDCP-tauglicher DVD-Player verwendet wer-
den.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV Geräte - PC
PC Eingang typische Bildschirmmodi
Der Bildschirm hat eine maximale Auflösung von
1280 x 768, einen vertikalen sync. Frequenzbe-
reich von 50-75Hz und einen horizontalen sync.
Frequenzbereich von 30-69 KHz. Die folgende
Tabelle beinhaltet einige typische Video Bildschirm-
modi.
Die Standardauflösung des TFT-LCD Bildschirm ist
1280 x 768.
Deshalb ist es ratsam, als Modus 14 für die beste
PC Eingang Bildschirmqualität zu wählen.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Reinigung und Pflege
Vor dem Reinigen ist das Gerät mit dem
Netzschalter auszuschalten !
ꢀ
ꢀ
Unsachgemäße Behandlung und Reinigung
können den Bildschirm irreparabel beschä-
digen. Beachten Sie daher die Vorschriften
zur Behandlung und Pflege des Gerätes.
Behandlung:
Behandeln Sie die Bildschirmoberfläche sehr sorg-
sam und pfleglich.
Vermeiden Sie jegliche mechanische Beanspru-
chung der Bildschirmoberfläche durch Schlag,
Stoß, Druck, Kratzen, Schaben etc., da dies eine
Beschädigung verursachen kann.
Verhindern Sie den Kontakt mit spitzen, scharf-
kantigen oder harten Gegenständen.
Die Bildschirmoberfläche ist vor Verschmutzung zu
bewahren.
Pflege und Reinigung:
Vor dem Reinigen das Gerät abschalten und den
Netzstecker ziehen.
Die Reinigung der Bildschirmoberfläche muß mit
einem trockenen, weichen Reinigungstuch (z.B.
Microfasertuch) erfolgen. Sollten dennoch stärkere
Verschmutzungen entstanden sein, kann die Reini-
gung der Bildschirmoberfläche mit einem nur
leicht angefeuchteten, weichen Tuch erfolgen.
Achten Sie darauf, dass niemals Wasser oder
andere Flüssigkeiten in das Gerät eindringen, da
diese eine Beschädigung des Gerätes verursa-
chen.
Ziehen Sie sofort den Netzstecker, falls Fremdkör-
per wie Wasser, sonstige Flüssigkeiten, Metallteile
usw. in den Bildschirm gelangt sind. Versuchen Sie
niemals mit irgendwelchen Gegenständen oder
mit den Händen in das Gerät zu fassen.
Es besteht die Gefahr eines elektrischen Schocks
oder Unfalls.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Technische Daten
Netzspannung:
220 - 240 V
50 Hz
˜
Antenneneingang:
75 Ohm asymmetrisch
DIN 45325
Empfangsbereich:
Standardkanäle 2 - 12, 21 - 69
Sonderkanäle S1 - S20, S21 - S41,
S42 ... S46 (Belgien Kanäle OIR)
Leistungs-
aufnahme:
Plasma-Bildschirm
und Tuner-Box
2 x 14 W
(2 x 8 W)
ca. 355 W
Energieverbrauch pro Stunde (Wh):
siehe Leistungsaufnahme in W x 1 Stunde
Stand-by:
Plasma-Bildschirm: ca. 3 Wh
Tuner-Box:
ca. 7 Wh
Abmessungen:
Plasma-Bildschirm mit Standfuß (H x T x B)
717 mm x 340 mm x 1049 mm
Breite mit angebauten Lautsprechern: 1295 mm
Technische Änderungen und Irrtümer vorbehalten !
41
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Batterie-Entsorgung
Batterien/Akkus gehören nicht in den Hausmüll!
Bitte bedienen Sie sich bei der Rückgabe ver-
brauchter Batterien/Akkus eines vorhandenen
Rücknahmesystems.
Bitte geben Sie nur entladene Batterien/Akkus ab.
Batterien/Akkus sind in der Regel dann entladen,
wenn das damit betriebene Gerät
- abschaltet und signalisiert „Batterien leer“
- nach längerem Gebrauch der Batterien nicht
mehr einwandfrei funktioniert.
Zur Kurzschlußsicherheit sollten die Batteriepole
mit einem Klebestreifen überdeckt werden.
Deutschland: Als Verbraucher sind Sie gesetzlich
verpflichtet, gebrauchte Batterien zurückzugeben.
Sie können Ihre alten Batterien überall dort unent-
geltlich abgeben, wo die Batterien gekauft wur-
den. Ebenso bei den öffentlichen Sammelstellen in
Ihrer Stadt oder Gemeinde.
Diese Zeichen finden Sie auf schadstoffhaltigen
Batterien:
Pb = Batterie enthält Blei
Cd = Batterie enthält Cadmium
Hg = Batterie enthält Quecksilber
Li = Batterie enthält Lithium
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Plasma-Bildschirm
reagiert nicht auf
Fernbedienung
Mögliche Ursache
• Kein Sichtkontakt zwischen
Fernbedienung und Plasma-
Bildschirm.
Abhilfe
• Sichtkontakt herstellen.
• Sonnenlichteinstrahlung
vermeiden.
• Direktes Sonnenlicht scheint
auf des Infrarotfenster des Plas-
ma-Bildschirmes.
• Batterien erneuern.
• Batterien der Fernbedienung
leer.
• Plasma-Bildschirm und/
oder Tuner-Box mit der
Netztaste einschalten.
• Plasma-Bildschirm oder
Tuner-Box sind mit der
Netztaste ausgeschaltet.
• Plasma-Bildschirm mit
der Netztaste aus- und
wieder einschalten.
• Störung am Prozessor
• LVDS-Kabel (Verbindung
Plasma-Bildschirm - Tuner-Box)
ist nicht korrekt angeschlossen
• Verbindung überprüfen.
Ihr Metz-Produkt wurde mit hochwertigen
Materialien und Komponenten entworfen
und hergestellt, die recycelbar sind und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische
und elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden müssen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder
im Recycling Centre.
Bitte helfen Sie mit, die Umwelt in der wir
leben, zu erhalten.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
BLACK PANTHER
616
491
508
607
614
466
505
Codes Video
BLAUPUNKT
496
527
609
621
487
502
530
610
507
532
612
Metz VG61
532
VF21, VF44, VF46
VF61, VE21, VE43
VE44, VE45, VD21
VD43, VD44, VD45
VC21, VC43, VC44
VC62, 21VB11
BONDSTEC
BONDSTECBRANDT
BRANDT ELECTRONIQUE 503
574
504
505
524
BRAUN
570
450
481
466
588
BRIONVEGA
BROKSONIC
BRUNS
575
42VB12, 21VA12
21VA13, 42VA11
64VA14, 9836,9837
9847, 9874, 9875
9876, 9877
487
590
490
593
BUSH
CALIN
481
481
481
547
527
505
487
487
606
481
466
547
487
466
CALIX
CANDLE
CARRERA
CARVER
CGE
Metz VF22, VF47
VF48, 9843, 9844
9849
568
573
CIE
CIMLINE
CLARIVOX
CLASSIC
CLATRONIC
COLORTYME
COLT
481
487
547
Metz VH22, VH47
VH48
ACTION
ADMIRAL
ADVANTZ
ADVENTURA
ADYSON
AGHA
468
481
481
468
487
547
481
477
481
505
575
487
487
466
547
529
529
487
575
478
575
481
481
527
528
505
575
466
481
487
481
487
547
547
562
CONDOR
616
504
487
507
481
CONTINENTAL EDISON 503
505
547
527
CRAIG
481
481
487
490
575
466
505
547
CROSLEY
CROWN
CROWN
CRYSTAL
CTC
547
616
AIWA
505
572
575
616
AKAI
482
508
609
483
546
612
484
554
CURTIS MATHES
CYBEREX
547
468
AKIBA
AKURA
505
588
DAEWOO
DANSAI
DAWA
DAYTRON
DE GRAAF
DECCA
DECCAVIDEO
DENON
DIGITAL
DORIC
466
487
575
466
529
528
528
527
477
601
547
503
530
505
468
487
553
ALBA
593
ALLORGAN
ALLSTAR
AMWAY
ANITECH
ART TECH
ASA
490
481
529
528
ASBERG
ASTRA
481
504
481
505
505
487
547
487
ASUKA
DTS
DUAL
ASUKA
527
527
ASWO
AUDIO DYNAMICS
AUDIOSONIC
AUDIOTON
AUDIOVOX
AVIS
DUEL
DUMONT
DYNATECH
616
547
583
ECONOMIC
510
487
616
487
481
481
547
487
481
EDISON
BAIRD
505
503
487
513
607
547
468
466
ELBE
BANG & OLUFSEN
BASIC LINE
BAUR
ELCATECH
ELECTROHOME
ELECTROPHONIC
ELIN
547
616
547
609
565
612
599
BEAUMARK
BELL & HOWELL
BESTAR
ELTA
EMERSON
616
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
EPC
505
466
487
586
604
586
510
598
616
JENSEN
JETPOINT
JVC
505
575
503
520
515
ESC
ETZUKO
EUROPHON
EXPERT
504
545
521
505
603
519
JVC_LCD
FERGUSON
501
555
487
468
477
468
481
505
574
523
595
524
596
KAISER
KAISUI
KAPSCH
KARCHER
KENDO
KENWOOD
KLH
575
487
600
575
483
468
481
487
481
487
473
FIDELITY
FINLUX
FIRST LINE
FISHER
601
477
481
473
487
478
487
528
575
505
487
FUNAI
571
KLIT
GAB
487
466
547
528
466
575
487
468
556
466
617
468
468
542
601
481
451
457
461
491
496
530
585
610
602
KODAK
KORPEL
KUBA
GBC
GE
504
505
547
510
517
GEC
601
603
604
GELOSO
GITEM
GOLDHAND
GOLDSTAR
LEYCO
487
578
575
481
601
481
481
487
468
518
468
LG
490
481
575
487
621
505
474
557
605
487
452
458
462
492
497
531
600
611
LIESENKOTTER
LLOYD
565
487
606
491
491
509
478
601
477
547
610
530
552
616
LLOYD’S
LOEWE
LOEWE OPTA
LOGIK
GOODMANS
575
527
547
483
GRAETZ
GRANADA
600
477
565
606
604
453
459
463
493
507
563
606
612
603
532
575
616
LUXOR
LXI
481
GRANDIN
GRUNDIG
MAGNADYNE
M ELECTRONICS
MAGNASONIC
MAGNAVOX
MAGNIN
MAGNUM
MANESTH
MARANTZ
MARQUANT
MARTA
575
547
470
481
481
581
487
491
487
481
481
486
562
527
527
468
487
547
547
606
477
477
542
487
481
466
601
454
460
464
495
527
584
609
613
481
507
547
582
487
527
547
547
GRUNDIG
528
490
565
566
GUTTRONIC
HANSEATIC
HANTAREX
HARLEY DAVIDSON
HARVARD
HCM
HEADQUARTER
HINARI
481
575
481
481
466
468
487
475
481
530
604
487
575
MATRIX
MATSUI
509
586
560
601
561
610
487
487
MATSUSHITA
MEDIATOR
MEMOREX
MEMPHIS
MGA
490
481
547
509
476
485
535
HINARIHITACHI
HITACHI
477
503
601
478
505
603
MGN
MINERVA
MINOLTA
MITSUBISHI
609
610
612
527
477
575
HYPSON
505
609
547
519
612
468
IMPERIAL
510
509
510
616
481
575
468
600
466
487
481
450
466
575
547
487
INGERSOL
INNO HIT
575
MULTITECH
MURPHY
481
487
INNO HIT
INTERBUY
INTERDISCOUNT
INTERFUNK
NAD
547
507
504
450
491
509
519
527
601
565
603
575
604
NATIONAL
NEC
505
469
493
510
528
576
470
496
512
541
INTERVIDEO
INTERVISION
IRRADIO
ITT
NECKERMANN
477
505
513
565
487
468
481
575
483
606
505
ITV
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
575
575
487
466
481
606
450
488
505
518
554
601
500
515
602
575
610
611
616
QUELLE
478
496
505
512
529
599
610
616
466
484
497
508
513
541
604
611
621
487
503
509
519
565
606
612
491
504
510
528
575
609
614
NEI
NESCO
NIKKAI
NIKKO
NOBLIKO
NOKIA
468
489
510
547
557
603
503
521
470
503
516
551
567
604
504
524
483
504
517
553
600
QUESTAR
RADIALVA
RADIOLA
RADIONETTE
RADIX
RANDEX
RANDIU
481
527
601
497
481
481
601
477
468
601
503
481
481
466
487
575
604
527
505
574
NOVATRONIC
RANK/BUSH/MURPHY
RCA
OCEANIC
OKANO
OLYMPIC
OLYMPUS
ORION
483
487
466
507
481
537
560
527
508
544
609
616
489
601
604
481
481
483
547
547
617
REALISTIC
REDIFFUSION
REX
505
509
538
561
474
512
565
610
620
531
558
589
493
513
575
611
621
536
559
591
496
541
599
612
RICOH
ROADSTAR
ROYAL
487
487
547
OTTO VERSAND
SABA
499
515
574
486
467
516
606
547
510
597
487
487
509
468
551
527
450
477
510
563
573
582
481
468
487
509
503
466
466
468
487
481
547
509
609
459
468
479
491
503
521
601
509
468
517
504
524
603
575
470
505
540
SABA
SABA
SAISHO
SALORA
SALORA
SAMBERS
SAMEX
SAMSUNG
483
575
PAEL
606
481
507
533
623
503
547
477
477
606
481
481
529
550
568
624
491
527
481
477
505
487
547
477
487
481
468
565
PALLADIUM
PANASONIC
487
508
549
491
527
600
505
532
601
547
575
575
PATHE MARCONI
PAXSONIX
PENNEY
PENTAX
PERSHIN
PHILCO
505
481
SANKY
SANSUI
SANWA
SANYO
505
527
547
469
577
470
586
471
507
491
530
563
575
625
565
527
507
547
564
620
547
528
548
565
621
SBR
PHILIPS
SCHAUB LORENZ
SCHNEIDER
468
478
527
564
575
604
483
481
529
569
578
505
487
530
571
581
PHILIPS
PHILIPS
PHILIPS
PHILIPS
PHILIPS (F)
PHONOLA
PILOT
575
SCOTT
SEARS
477
490
528
504
481
510
PIONEER
PRIMA
527
547
490
539
529
483
575
547
SEG
547
545
SEI-SINUDYNE
SELECO
SENTRA
SETRON
SHARP
PROFEX
PROFILE
PROSCAN
PROTEC
PULSAR
PULSER
505
481
487
544
547
481
575
SHINTOM
SHIVAKI
SHOGUN
SHORAI
SICE
547
575
PYE
QTY1
592
468
481
507
450
470
612
461
469
480
492
QUARTER
QUARTZ
QUASAR
QUELLE
SIEMENS
462
470
481
493
464
472
486
494
547
527
459
471
461
474
464
477
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
SIEMENS
495
511
607
612
575
481
487
509
599
466
575
601
481
506
541
547
477
487
527
481
496
525
609
614
497
530
610
498
584
611
TRIAD
TRIX
575
481
466
TVA
UHER
466
505
450
565
606
547
560
481
530
606
604
477
510
616
575
609
481
543
503
SILMA
SILVA
SINGER
SINUDYNE
ULTRAVOX
UMA
UMA
547
513
575
527
616
575
601
612
604
614
UNITECH
UNITED
UNIVERSUM
SOLAVOX
SONOKO
SONOLOR
SONTEC
SONY
604
483
547
609
491
571
612
527
575
621
512
599
513
623
514
UNIVOX
VICTOR
505
466
554
547
481
481
545
562
SR1000
STS
SUNWOOD
SYLVANIA
SYMPHONIC
VIDEOMASTER
VIDEOPLUS
VIDEOSONIC
VIEWMARK
VIEWMAX
589
547
487
612
527
TAISHO
509
609
623
468
528
505
505
466
487
527
575
563
575
481
503
505
500
515
579
547
505
609
487
487
481
575
547
499
505
60
474
505
586
612
501
575
609
481
474
547
481
487
487
WARDS
477
575
481
487
565
TALENT
WEGAVOX
WELTBLICK
TANDBERG
TANDY
WHITE WESTINGHOUSE 450
TASHIKO
TATUNG
TEAC
529
527
WINSTON
WIZJA
WORLDVIEW
575
528
575
TEC
TECHLINE
TECHNICS
TECHNILAND
TECHNISAT
TEKNANT
TEKNIKA
TELEAVIA
TELEAVIA
TELEFUNKEN
XR1000
487
547
532
YAMISHI
YOKAN
YOKO
487
487
466
510
481
547
487
490
ZENITH
481
503
521
594
504
524
505
574
Codes DVD-Player
TELEORDER
TELERENT
TELESERVICE
TELETECH
TENOSAL
TENSAI
METZ
204
214
239
230
AKAI
612
BLUEsky
254
256
Boxford
487
593
490
509
CYBER HOME
223
247
Cytron
THOMAS
THOMSON
DENON
216
243
248
500
524
6226
482
542
604
503
574
504
594
D-i-K
DUAL
THORN
501
565
606
503
575
609
EMERSON
263
GAME
253
262
255
222
GOLDSTAR
GRAND PRIX
GRUNDIG
THORN-FERGUSON
503
601
612
487
481
504
604
505
606
232
210
238
260
HARMAN/KARDON
206
205
HITACHI
261
263
TOKAI
TOSHIBA
505
527
JVC
212
KENWOOD
208
270
246
231
TOTEVISION
TOWADA
TOWIKA
547
490
KISS
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
DIORA
DUAL
949
822
LABWAVE
LG
200
263
215
219
201
832
831
859
920
994
953
LINN
FISCHER
830
LOEWE
MARANTZ
218
271
241
221
240
256
269
219
272
236
258
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
885
872
888
908
MbyN
MEDIENCOM
MEDION
MEGATON
MUSTEK
228
257
911
931
912
934
913
935
HARMAN KARDON
905
853
MYRYAD
HITACHI
NAD
207
228
INTERSOUND
960
937
NONAME
ITT
ONKYO
209
266
225
267
226
274
ORION
JVC
844
903
848
904
849
992
902
PANASONIC
216
276
219
234
278
203
251
228
275
PHILIPS
220
235
227
236
233
237
KENWOOD
820
877
948
908
847
878
963
858
879
859
925
PIONEER
PROLINE
204
249
250
KRELL
273
268
LINN
908
924
964
946
LUXMAN
967
SAMSUNG
SCHAUB LORENZ
SCHNEIDER
SEG
210
255
244
201
224
243
211
242
METZ HE11
MARANTZ
MATSUI
882
833
908
955
908
908
908
972
908
955
248
263
229
263
264
908
909
SHERWOOD
SILVA SCHNEIDER
SONY
MEDION
MERIDIAN
MAGNAVOX
MICROMEGA
MINOWA
MISSION
MTC
265
SUNKAI
TECHNICS
216
228
213
202
217
259
277
245
TEVION
THOMSON
TOSHIBA
246
266
234
UNITED
252
216
255
278
NAD
947
908
930
938
888
802
806
NAIM
YAMAHA
NAKAMICHI
NOKIA
NONAME
NSM
Codes HIFI - CD
803
807
804
861
805
AIWA
815
856
856
957
929
908
909
816
857
817
872
884
921
AKAI
AKKAI
OKANO
869
819
871
827
AMSTARD
AMSTRAD
ARCAM
ASWO
ONKYO
881
870
911
940
976
942
956
PALLADIUM
PANASONIC
PHILIPS
810
834
833
965
824
862
923
906
908
851
915
908
866
918
909
BANG & OLUFSEN
BRAUN
BUSH
808
975
888
PIONEER
825
863
826
864
850
922
CAMBRIDGE
CAMBRIDGE AUDIO
CARVER
945
945
908
PMG
PROTON
QUAD
908
965
DAEWOO
876
801
853
961
DENON
812
899
962
845
900
846
901
RADIOTONE
958
911
RADMOR
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
REVOX
REVOX/STUDER
ROTEL
829
910
818
DENON
834
891
972
899
837
936
840
892
841
970
879
971
908
951
DIORA
DUAL
900
850
SABA
926
908
939
908
852
821
869
888
928
960
978
982
986
851
985
935
998
SAE
SAMSUNG
SANSUI
SANYO
SCHNEIDER
966
968
FISCHER
893
894
860
840
870
892
929
972
979
983
987
919
841
873
911
955
973
980
984
988
868
885
927
959
977
981
985
989
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
964
833
867
976
979
980
HARMAN KARDON
926
915
984
931
HITACHI
ITT
918
919
SHARP
SHERWOOD
SIEMENS
799
936
833
872
876
886
891
892
800
943
867
873
880
887
969
813
944
868
874
883
889
970
847
JVC
862
994
863
995
974
996
975
997
869
875
885
890
971
KENWOOD
848
957
917
958
935
990
936
993
SINOTEC
LINN
888
876
889
877
SINOTEC (PEPSI-DOSE) 892
LUXMAN
884
989
SONY
842
896
990
888
908
843
897
991
945
893
898
895
932
METZ HE11
961
887
MARANTZ
922
904
999
905
SUPERTECH
SYLVANIA
NAD
903
927
920
948
846
902
959
906
901
NAKAMICHI
NOKIA
T+A
882
974
T+A ELECTROAKUSTIK 882
OKANO
949
847
TECHNICS
809
950
954
823
916
993
917
918
ONKYO
856
TENSAI
THOMSON
ONKYO
960
PALLADIUM
PANASONIC
PHILIPS
944
928
921
853
938
943
UHER
814
869
966
995
929
976
854
939
988
982
980
855
941
UNIVERSUM
872
979
908
855
952
933
999
912
942
PIONEER
UNKNOWN
YAMAHA
828
941
854
RADMOR
978
860
977
REVOX
861
885
REVOX/STUDER
Codes HIFI - Tape
SAMSUNG
883
897
985
930
866
872
918
976
839
890
911
886
896
AIWA
AKAI
842
963
845
934
916
976
843
844
962
SANY
SANYO
SCHNEIDER
849
945
913
951
933
987
937
867
873
919
986
868
874
947
869
878
964
AMSTRAD
ASWO
BANG & OLUFSEN
BRAUN
BUSH
836
870
835
SHARP
SHERWOOD
864
908
923
993
909
910
DAEWOO
907
SIEMENS
880
881
882
946
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
947
953
964
865
967
992
950
954
976
925
968
951
955
952
956
NAD
459
419
748
NAKAMICHI
NONAME
SONY
965
969
966
991
OKANO
733
379
736
440
ONKYO
460
451
742
T+A
871
961
898
PALLADIUM
PANASONIC
PHILIPS
731
371
427
383
996
735
432
450
384
997
T+A ELEKTROAKUSTIK 961
TECHNICS
THOMSON
838
852
981
886
859
983
895
914
PIONEER
436
998
437
999
UNIVERSUM
868
947
875
950
REVOX
386
427
428
378
REVOX/STUDER
RADMOR
ROTEL
YAMAHA
857
924
858
932
Codes HIFI - Tuner
SAMSUNG
411
475
433
374
391
395
399
403
409
443
733
749
373
413
426
479
737
747
749
463
476
990
380
392
396
400
404
412
469
735
465
473
AIWA
376
734
452
469
744
427
377
737
455
745
993
464
SANYO
SCHNEIDER
995
388
393
397
401
407
441
470
746
AKAI
390
394
398
402
408
442
732
748
AMSTRAD
468
424
ASH
ASWO
BANG & OLUFSEN
369
748
BUSH
DAEWOO
458
371
445
461
370
739
372
471
SHARP
SHERWOOD
SIEMENS
446
456
427
480
738
DENON
423
991
457
477
732
739
478
733
746
DIORA
DUAL
381
449
994
FISCHER
434
SINOTEC
SINOTEC (PEPSI-DOSE) 749
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
746
737
748
427
SONY
389
422
466
416
420
431
421
462
SUPERTECH
T+A
429
450
405
743
430
HARMAN KARDON
418
453
730
991
T+A ELEKTROAKUSTIK 743
HITACHI
TECHNICS
TENSAI
THOMSON
387
406
382
ITT
412
JVC
414
448
425
444
446
447
740
UHER
375
403
737
UNIVERSUM
467
415
473
435
733
454
KENWOOD
417
741
439
994
YAMAHA
385
992
LINN
472
438
LUXMAN
474
Codes HIFI - Amp
METZ HE11
MARANTZ
MINOWA
MISSION
743
450
409
426
AIWA
777
753
785
840
776
793
985
754
813
986
766
829
AKAI
AMSTRAD
831
ASH
ASWO
NOKIA
410
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Codeliste
SAMSUNG
SANYO
828
750
763
782
786
814
842
961
965
969
973
818
825
762
768
779
785
948
786
837
756
764
783
794
815
951
962
966
970
978
990
832
763
769
780
794
950
844
846
BANG & OLUFSEN
BRAUN
BUSH
996
960
748
SCHNEIDER
768
784
812
827
953
963
967
971
779
785
813
840
956
964
968
972
782
DAEWOO
770
751
817
835
952
DENON
789
988
790
791
DIORA
DUAL
981
820
995
839
FISCHER
750
SHARP
SHERWOOD
SIEMENS
833
766
770
781
800
GRUNDIG
794
749
779
795
766
804
782
767
775
784
947
GOODMANNS
GOLDSTAR
HARMAN KARDON
760
751
823
HITACHI
SINOTEC
SINOTEC (PEPSI-DOSE) 786
ITT
827
SONY
SUPERTECH
787
782
788
974
836
991
976
JBL
821
792
975
816
JVC
819
818
T+A
774
959
806
T+A ELEKTROAKUSTIK 774
KENWOOD
755
771
TECHNICS
805
993
958
980
LINN
794
810
795
845
TENSAI
THOMSON
LUXMAN
954
798
955
METZ HE11
MARANTZ
MEDION
MERIDIAN
MINOWA
MISSION
774
794
785
795
978
799
UHER
987
763
963
795
UNIVERSUM
766
838
824
844
830
YAMAHA
752
809
979
NOKIA
NAD
NAKAMICHI
NIAM
NONAME
826
834
822
795
782
OKANO
763
772
765
982
ONKYO
PALLADIUM
761
783
991
PALLADIUM/OKANO 764
PANASONIC
PHILIPS
805
793
797
757
957
808
794
798
758
994
795
803
795
796
992
PIONEER
PRO-LOGIC
QUAD
795
RADIOTONE
841
801
843
796
983
RADMOR
802
977
797
984
803
798
REVOX
REVOX/STUDER
ROTEL
SABA
811
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Geräte-Pass
Bundesrepublik Deutschland
Nur gültig, wenn ordnungsgemäß und vollständig ausgefüllt. Durch Änderungen verliert der
Geräte-Pass seine Gültigkeit. Sorgfältig aufbewahren. Verlorene Urkunden werden nicht ersetzt.
Typ:
Verkaufsdatum:
Gerätecode:
Anschrift des Käufers:
Unterschrift des Käufers
Stempel und Unterschrift des Fachhändlers
1. Die nachfolgenden Bestimmungen haben nur für den privaten Gebrauch Gültigkeit.
2. Die Garantiezeit - 24 Monate - beginnt mit dem Abschluß des Kaufvertrages bzw. mit dem Tag der
Auslieferung des Gerätes an den Käufer (Endverbraucher).
3. Garantieanspüche können nur unter Nachweis des Kaufdatums durch Vorlage der durch den
Fachhändler vollständig ausgefüllten Garantieurkunde und des maschinell erstellten Kaufbeleges gel-
tend gemacht werden.
4. Beanstandete Geräte bitten wir zusammen mit dieser Garantieurkunde und dem Kaufbeleg entweder
über den Fachhändler oder direkt an die
Firma Metz-Werke GmbH & Co KG - Zentralkundendienst - Ohmstrasse 55, 90513 Zirndorf,
transportsicher verpackt unter genauer Schilderung der Beanstandung einzusenden. Sie können unter
den gleichen Bedingungen auch an die autorisierten Kundendienststellen der Firma Metz-Werke
GmbH & Co KG eingesandt werden.
Hin- und Rücksendung erfolgen auf Gefahr des Käufers.
5. Die Garantie besteht darin, daß Geräte, die infolge eines anerkannten Fabrikations- oder
Materialfehlers defekt geworden sind, kostenlos repariert oder, soweit eine Reparatur unverhältnismä-
ßig ist, ausgetauscht werden.
Eine weitergehende Haftung, insbesondere für Schäden, die nicht am Gerät selbst entstanden sind, ist
ausgeschlossen. Dies gilt nicht, soweit im Falle des Vorsatzes oder der groben Fahrlässigkeit zwingend
gehaftet wird.
Garantieleistungen bewirken weder eine Verlängerung der Garantiezeit, noch wird für die ersetzten
oder nachgebesserten Teile eine neue Garantiezeit begründet.
6. Unsachgemäße Behandlung und Eingriffe durch den Käufer oder Dritte schließen die Garantiever-
pflichtungen sowie alle weiteren Ansprüche aus. Ausgenommen von der Garantie sind ferner Schäden
oder Fehler, die durch Nichtbeachtung der Gebrauchsanleitung, mechanische Beschädigung, ausge-
laufene Batterien oder durch höhere Gewalt, Wasser, Blitz etc. entstanden sind. Ferner sind Verschleiß,
Verbrauch sowie übermäßige Nutzung von der Garantie ausgenommen.
7. Der Garantieanspruch besteht nur in Deutschland und ist ab 01.01.2002 gültig.
8. Durch diese Garantieurkunde werden die Gewährleistungsansprüche des Käufers gegenüber dem
Verkäufer nicht berührt.
190 90 0391
Download from Www.Somanuals.com. All Manuals Search And Download.
Plasma TV Set 42“ PIP 42TM92
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you
Contents
Dear Customer,
1.
Setting up . . . . . . . . . . . . . . . . . . . . . . .55
1.1 Wall mounting . . . . . . . . . . . . . . . . . . . .56
1.2 Loudspeaker . . . . . . . . . . . . . . . . . . . . .57
1.3 Installation . . . . . . . . . . . . . . . . . . . . . . .58
1.4 Controls on the plasma monitor . . . . . . . .58
1.5 Controls and connectors on the tuner box 59
thank you for selecting this Metz
product.
In this TV set, we have provided
a menu guidance system which,
we believe, will permit you to
operate the set easily.
2.
Safety notes . . . . . . . . . . . . . . . . . . . . . .60
2.1 General information . . . . . . . . . . . . . . . .61
3.
4.
5.
The remote control . . . . . . . . . . . . . . . . .62
Operation without the remote control . . . .68
Selecting your country . . . . . . . . . . . . . .69
However, before using the set for
the first time, you should at least
read Sections 1 to 7 of these
Operating Instructions.
5.1 Selecting a language . . . . . . . . . . . . . . .70
6. Tuning to TV stations . . . . . . . . . . . . . . . .71
6.1 Station logos . . . . . . . . . . . . . . . . . . . . .75
6.2 Sorting the stations . . . . . . . . . . . . . . . . .76
Your METZ-WERKE
7.
8.
9.
Selecting a station . . . . . . . . . . . . . . . . .77
Picture settings . . . . . . . . . . . . . . . . . . . .78
Sound settings . . . . . . . . . . . . . . . . . . . .79
10. Special functions
Picture in picture (PIP) . . . . . . . . . . . . . . .80
Picture size . . . . . . . . . . . . . . . . . . . . . .81
Split screen . . . . . . . . . . . . . . . . . . . . . .82
Freeze frame . . . . . . . . . . . . . . . . . . . . .82
Sleep timer . . . . . . . . . . . . . . . . . . . . . .83
Displaying the time . . . . . . . . . . . . . . . . .83
11. Teletext . . . . . . . . . . . . . . . . . . . . . . . . .84
12. Connecting headphones . . . . . . . . . . . . .85
13. AV devices . . . . . . . . . . . . . . . . . . . . . . .86
Selecting AV devices . . . . . . . . . . . . . . . .87
Copying . . . . . . . . . . . . . . . . . . . . . . . .88
VCR function . . . . . . . . . . . . . . . . . . . . .89
Connecting the PC via VGA / DVI input . .90
PC input typical display modes . . . . . . . .91
14. Cleaning the set . . . . . . . . . . . . . . . . . . .92
15. Technical data . . . . . . . . . . . . . . . . . . . .93
16. Disposal of exhausted batteries . . . . . . . .94
Troubleshooting . . . . . . . . . . . . . . . . . . .95
Code list . . . . . . . . . . . . . . . . . . . . . . . .96
The plasma monitor is a product
which employs the latest techno-
logy.
Occasionally, some inactive
pixels may appear on the screen
as fixed blue, green or red dots.
Please note that these do not
affect the performance of the TV
set.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Setting up
The Plasma TV Set consists of the components: plasma monitor, stand, wall mounting
bracket, two loudspeakers with bases and the tuner box.
Fitting the base
The stand has two vertical panels at the front and back. The (higher) rear panel, with
a slot for the cables, is secured with four screws and must be removed before the
plasma TV set is mounted on the stand.
Slide the stand into the guides on the rear of the TV set and secure it carefully with
four screws (M5 x 20 mm).
Plug in the power cable and the cable to the tuner box, lay them through the slot in
the rear panel and secure the panel to the rear of the stand.
Front panel, fixed
Cable slot
Rear panel, removed
Left loudspeaker
Plasma monitor
4 screws
M5 x 12mm
Right loudspeaker
Loudspeaker bracket
Stand
4 screws
M5 x 20mm
ቢ
55
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Wall mounting
Wall mounting
Non-compliance with these instructions can result in serious injuries to
persons and/or major damage to the TV set.
The plasma monitor may be mounted only on vertical walls, using the
wall bracket.
Never attempt to mount the wall bracket and the monitor on your own;
always obtain the assistance of a second person.
• Take great care when securing the wall bracket to the wall. The bracket must not
only support the monitor under normal circumstances, but must also withstand any
shocks, vibration, etc. which may occur.
• Before starting work, check the stability and thickness of the wall. Ask your local
DIY store for suitable metal screws and wall plugs.
• The wall must be solid and capable of handling the load (i.e. it must be made of
bricks, limestone blocks, concrete or similar materials).
• If the wall is made of other materials (such as wood, plasterboard, etc.) have the
wall bracket mounted by an experienced tradesman.
MOUNTING BRACKET
SUSPENSION SCREWS
PLASMA MONITOR
PLASTIC WALL PLUG
(M10 x 50)
WALL MOUNTING
SCREW
BRACKET
(M7 x 60)
MOUNTING HOLE
ባ
WALL
56
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Wall mounting
Mounting the plasma monitor on a wall
1. To mount the plasma monitor on a wall, first remove the stand (Fig. 1) by unscre-
wing the four screws (M5 x 20) which hold it to the monitor and pulling the stand
off.
The plasma monitor can be mounted on a wall with or without the loudspeakers
attached to it.
2. The wall mounting bracket is secured to the wall with four wall plugs (Ø10 x 50)
and four screws (Ø7 x 60) as shown in Fig. 2.
First select the position for the monitor. Hold the mounting bracket in a horizontal
position against the wall and mark the positions of the four mounting holes on the
wall. Drill four holes for the plastic wall plugs, insert the plugs and secure the
mounting bracket to the wall with four screws (Ø7 x 60).
3. Lift the plasma monitor and engage the two suspension screws on the rear of the
monitor with the matching holes in the wall mounting bracket.
1.2 Loudspeakers
Mounting the loudspeakers on the monitor
Place the plasma monitor face-down on a smooth, flat surface such as a table
(Fig. 3). Place the loudspeakers on the left and right sides of the monitor.
Align the loudspeaker brackets (two for each loudspeaker) with the holes in the plas-
ma monitor and secure each bracket with four screws (M5 x 12) to the loudspeaker
and the monitor. Connect the loudspeaker cables to the monitor.
PLASMA MONITOR
ቤ
LOUDSPEAKER BRACKET
RIGHT
LOUDSPEAKER
LEFT
LOUDSPEAKER
RED
SCREW
(M5 x 12)
LOUDSPEAKER SOCKETS
BLACK
57
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Installation
• Take care that no bright lights (including sunshine) shine directly on the screen, sin-
ce this can cause reflections and reduce the apparent brilliance of the picture.
• The best viewing distance is about five times the diagonal dimension of the screen.
For a TV set with a 107 cm screen, it is thus about 5.35 m.
• All cables and components connected between the antenna/broadband socket in
the wall and the TV set must comply with European Standard EN 60966-2-4.
• There may be no magnetic fields in the immediate vicinity of the TV set. External
loudspeakers should thus be positioned at a suitable distance from the set.
• The antenna connection cable used for the set should have a screening attenuation
of at least 75 dB.
• The use of unapproved cables and components will invalidate the type approval of
the TV set.
1.4 Controls on the plasma monitor
Front view
ON/OFF SWITCH
PILOT LAMP
Rear view
Connector for LVDS
cable to tuner box
Socket for mains cable
58
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Controls and connectors on the tuner box
Front view
ቢ On/off switch
ባ Audio input left/right
ቤ Video input
ቧ Volume control
ቨ Programme selector P+ / P-
ቩ Menu key
ብ Headphone socket
ቦ S-VHS input
ቪ AV key/signal selection
Rear view
A Subwoofer output
B Loudspeaker output left/right
C Antenna
H SCART 3
I
SCART 4
J LVDS (output to plasma monitor)
D Video Out
E Video In
F SCART 1
G SCART 2
K Audio In
L DVI - input
M VGA - input
(from PC)
(from PC)
(from PC)
all pins connected
N Socket for mains cable
59
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Safety notes
With plasma displays, there is always
the risk that an image may be
- vases, etc. containing liquids
on or above the TV set. Hot wax or other
liquids which enter the set will destroy its
electronic components. In such cases, safe
operation of the set is no longer guaran-
teed.
"burnt" into the screen if, for exam-
ple, a static picture (such as a freeze-
frame display of a TV picture, a Tele-
text page, a PC image or a signal
from a DVD player) is displayed for a
long period. This results in differences
in the brightness between illuminated
and inactive pixels which can become
visible as soon as a different picture is
displayed.
• Thunderstorms can damage electrical devi-
ces. Lightning hitting overhead power
cables or the antenna can cause considera-
ble damage to the set, even if it is switched
off. If there is a risk of a thunderstorm, you
should remove the power cable from the
wall outlet and disconnect the antenna
cable from the outlet or from the TV set.
In order to prevent permanent damage to the
display, you should thus always take care
that static pictures are not displayed for long
periods. Wherever possible, make use of any
screen-saver functions offered by the connec-
ted devices (such as DVD player, video recor-
der or PC).
• Only suitably trained persons may open
the set and/or carry out repairs.
CAUTION: RISK OF ELECTRIC SHOCKS!
If repairs should be necessary, please consult
your local dealer.
• Place the TV set on a solid surface which is
capable of bearing the weight!
• Always switch off the TV set with the mains
switch before cleaning it!
• If you bring a cold TV set into a warm
room, wait until any condensation has eva-
porated before switching it on.
• Do not point the remote control into your
eyes and press any keys. The infrared radi-
ation can damage your eyes!
• The TV set is intended for use in dry rooms.
If, in exceptional cases, you want to use it
outdoors, take care that it is not exposed to
moisture (rain, splashwater, dew).
• Do not use rechargeable batteries in the
remote control. Use only two dry batteries
of the type LR03/AM4/AAA 1.5V Micro.
• The TV set is intended only for the reception
and display of picture and sound signals.
• TV sets need sufficient cooling to prevent
them from overheating. Ensure that the slots
in the rear cover are not blocked by cur-
tains, doily, newspapers, etc. Also keep the
slots on the bottom of the set free so that
cool air can enter the set.
• The TV set may be operated only from a
mains voltage of 220 – 240VAC , 50Hz.
˜
• Lay the mains cable so that no-one can trip
over it and so that no objects (furniture,
etc.) stand on it!
• If you install the TV set in a wall cabinet,
ensure that there is sufficient space around
it to permit the circulation of cooling air.
• Repairs may be carried out only by suitably
qualified persons.
• Do not position the TV set in the immediate
vicinity of a radiator or other heater, since
this could cause it to overheat.
• Do not place
- burning candles
60
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 General information
Before switching on
• Connect the plasma monitor to the tuner box
with the enclosed LVDS cable.
• Connect the mains cables of the plasma monitor
and the tuner box to a mains outlet socket.
• Press the on/off switch on the plasma monitor
and the tuner box to switch the two units to
standby mode. The LEDs on both units light red.
Switching on
After connecting the cables, wait for about five
seconds before switching on the plasma monitor
with the
key on the remote control or with the
P+
P–
P+/P- keys on the tuner box. The LEDs on both
units switch to green. The TV set is tuned to the
last station you were watching before it was swit-
ched off.
Switching off
Press the
key on the remote control to switch to
standby mode or press the on/off switch on the
plasma monitor.
Selecting stations
You can select the desired station with the numeric
keys, with the P+/P- keys on the remote control
or tuner box or with the aid of the station list.
Open the station list by pressing the INFO key and
use the cursor keys ꢂ ̈ ꢀ ꢁ to select the desired
station. Then close the station list by pressing the
INFO key again.
P+
P–
Adjusting the volume
The volume can be adjusted with the – + key.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
The Metz Remote Control RL 18 can be
used to control the TV set and the basic
functions of video recorders VCR1 and
VCR 2, a DVD player and HiFi units (such
as radio, cassette player, CD player,
amplifier, etc.) made by Metz or various
other manufacturers.
The remote control sends the commands to
the Tuner box with the aid of infrared radi-
ation. Always point the remote control at
the Tuner box when using it. The remote
control may occasionally interfere with the
operation of other infrared-controlled devi-
ces or systems (such as infrared headpho-
nes) within its range.
23
ቢ
22
21
ባ
ቤ
ቶ
ት
ብ
Ensure that no sunlight falls directly
on the TV set, since this may result in
malfunctions because the set cannot
detect the infrared signals from the
remote control.
ꢀ
ቴ
ታ
ቦ
ቧ
ቨ
Note that the TV set must be switched on
with the mains switch before it can be con-
trolled with the remote control.
The various operating levels of the remote
control are programmed as follows in the
factory:
ቲ
ቱ
ተ
•TV
Metz TV sets
ቯ
ቮ
ቭ
•VCR1 Metz VCR with remote control RH51
ቩ
ቪ
•VCR2 Metz VCR with remote control RF52
•DVD Metz DVD player with remote control
RG/RH37
•HiFi Metz HiFi CD receiver HE 11 with remote control
ቫ
F11
Do not use rechargeable batteries in
the remote control.
Use only two dry batteries of the type
LR03/ AM4/AAA 1.5V Micro.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
Back to TV mode
21
Overview of the key functions
ቢ ON
at the programme position selected
22
23
Select video input signal
Select key – Switches to the operating
level for AV devices
when the set was switched off
OFF (standby)
ባ Select aspect ratio (picture format)
ቤ Back to previous programme position
ብ Numeric keys
(direct programme selection)
ቦ Cursor key for menus
ቧ OK (confirm) / Freeze frame
ቨ Volume - +
ቩ Mute
ቪ Open TV menu
ቫ Programme -
ቭ Open Teletext
ቮ Display/hide programme list
ቯ Programme +
ተ Display/hide picture in picture (PIP)
ቱ Change PIP position
ቲ Exchange contents of PIP and main
picture
ታ Change size of PIP picture
ቴ Split screen
(display/hide double picture)
ት Display the time
ቶ Select Mono - Stereo + Dual tone.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
1. Programming the remote con- 1.2 Entering the codes for CD
trol for the individual devices
player, tuner and tape
In order to control your various devices
with the remote control, you must first
programme it with a three-digit number
for each operating level.
After executing steps a) to c), you
have about 15 seconds to make
further entries. If you do not do so,
the remote control returns automa-
tically to the TV operating level.
ꢀ
• TV (Plasma monitor)
The TV operating level is programmed
in the factory for the Metz 42“ Plasma
monitor. You cannot enter any other
code.
• VCR 1 (video recorder 1)
VCR 2 (video recorder 2)
DVD player
HiFi (e.g. amplifier, tuner, tape, etc.)
The remote control must be programm-
ed with suitable codes from the code
list.
a) Use the Select key to select the opera-
ting level HiFi. The coloured HiFi LED
lights.
b) Press the
key, release it and then
press the key:
...l–ll for CD player,
...
...
for tuner (radio) or
Ȅ
for tape (cassette recorder)
on the remote control until the LED blinks
once.
Note the factory settings (page 6)
and see the code list at the end of
this manual.
ꢀ
c) Enter the appropriate code (see the
code list) with the numeric keys.
If the code is accepted, the LED again
blinks twice. If you enter a non-exi-
stent code, the LED lights once for
about two seconds.
1.1 Entering the codes for VCR
and DVD
After executing steps a) to c), you
have about 15 seconds to make
further entries. If you do not do so,
the remote control returns automa-
tically to the TV operating level.
ꢀ
a) Use the Select key to select the desired
operating level. The coloured LED for
the selected level lights.
b) Press and hold the keys
until the LED blinks twice.
and l–ll
c) Enter the appropriate code (see the
code list) with the numeric keys.
If the code is accepted, the LED again
blinks twice. If you enter a non-exi-
stent code, the LED lights once for
about two seconds.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
1.3 Entering the code for a
2. Reading out a programmed
code
HiFi amplifier
After executing steps a) to d), you
have about 15 seconds to make
further entries. If you do not do so,
the remote control returns automa-
tically to the TV operating level.
After executing steps a) to e), you
ꢀ
ꢀ
have about 15 seconds to make
further entries. If you do not do so,
the remote control returns automa-
tically to the TV operating level.
a) Use the Select key to select the opera-
ting level HiFi. The coloured HiFi LED
lights.
a) In order to see which code is pro-
grammed for an operating level, first
proceed as described in 1.1 a) to b).
b) Press the
press the
twice.
key, release it and then
key until the LED blinks
b) Use the numeric keys to enter
ᕌ ᕌ ᕄ
. The LED blinks twice to
acknowledge the input.
ᕃ
c) Press the l–ll key. The LED blinks once. c) Press numeric key
to display the
first digit of the code. The LED now
blinks several times to show the value
(e.g. the LED blinks three times: the
digit 3 is programmed).
d) Enter the appropriate code (see the
code list) with the numeric keys.
If the code is accepted, the LED again
blinks twice. If you enter a non-exi-
stent code, the LED lights once for
about two seconds.
ᕄ
d) Press numeric key
to display the
second digit of the code. The LED now
blinks several times to show the value
(e.g. the LED does not blink: the digit
0 is programmed).
1.4 Search function
Proceed as described above for input of
the code for VCR, DVD, CD, tuner or
tape until you reach the step where the
code number is entered. Now enter the
code "001" to select the search function.
The LED blinks twice. Then press the
search key (the actual key depends on
the operating level; see the table on
pages 10 and 11) and hold it until the
device stops or switches off (an Off or
STOP command is transmitted automati-
cally every 1.5 seconds).
ᕅ
e) Press numeric key
to display the
third digit of the code. The LED now
blinks several times to show the value
(e.g. the LED blinks seven times: the
digit 7 is programmed).
In this example the programmed code is
ᕅ ᕌ ꢀ
thus
.
If you lose track during this operation,
simply start again at step 2c).
Now release the Search key and press
the Select key to save the code which
was found.
At the end of the search, when all exi-
sting codes have been interrogated, the
corresponding LED blinks five times.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
Key
V C R 1 / 2
23
ቢ
ቢ
On
On / Standby
22
21
ባ
ቤ
ብ
Record
Time in display
ባ
ቤ
0...9 Numeric keys: progr. selection
ꢀ ꢁ
ቶ
ት
Programme +/–
ቦ
ꢂ ̈
OK
Fast forward / Rewind
OK
ቧ
ቨ
ቩ
ቪ
ቫ
ቭ
ቮ
ቯ
ተ
ቱ
ቲ
ታ
ቴ
ት
ቶ
Vol.+/–
Mute
Menu
P-
Lautstärke +/– TV
TV mute
MENU
ብ
Switching voltage on/off
Text
Info Disp./hide programme list
P+
red
Pause
STOP / Search
PLAY
ቴ
ታ
ቦ
ቧ
ቨ
green
white
yellow
blue
Slow-motion
ቲ
ቱ
ተ
Ȅ
I-II
k
21
TV
AV
k
22
AV - Eingang
ቯ
ቮ
ቭ
k
23
Select
Auswahl Bedienebene
ቩ
ቪ
Note:
ቫ
The above key assignments are true for the
AV devices programmed in the factory. If
other AV devices shown in the code list are
used, the assignments may be different and
some may not be available.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The remote control
H i F i
Key
D V D
C D ( I-II )
T U N E R ( Ȅ )
T A P E (
)
ON: Display time/track
ON&AV, ON:On/Standby ON&AV, ON: On/Standby
ON:Radio-text on/off
ቢ
On
On / Standby
ባ
ቤ
ብ
Return
Angle
I-II & ON: CD
I-II & ON: CD
0...9 Numeric keys: title selection Num.keys: title select. Num.keys: progr.select.
ꢀ ꢁ
ꢂ ̈
OK
Cursor up/down
Cursor left/right
OK / Enter
TV volume +/-
TV mute
Title +/–
Programme +/–
Frequency +/–
ቦ
ቧ
ቨ
ቩ
ቪ
ቫ
ቭ
ቮ
ቯ
ተ
ቱ
ቲ
ታ
ቴ
ት
ቶ
Vol.+/–
Mute
Menu
P-
AMP volume +/-
AMP volume +/-
AMP volume +/-
MENU
Title
Text
Display
Info
P+
Pause
STOP/Search
PLAY
Pause
red
STOP/OPEN-CLOSE/Search Num.key ባ=Search
Search
green
white
yellow
blue
PLAY
EJECT
Skip +
Skip –
Audio
Ȅ & ON: Tuner
Ȅ & ON: Tuner
Ȅ
I-II
Subtitle
& ON: Tape input
& ON: Tape input
AUX input
k
21
TV
AV
k
22
Repeat
AUX input
AUX input
k
23
Select
Select operating level
Select operating level Select operating level Select operating level
Search:
Proceed as described above for entering the codes for VCR, DVD, CD, tuner, tape as far as the step
where the code number is entered. Then enter "001" for the search function. The LED blinks 2x to
acknowledge the input. Then press and hold the search key (which depends on the operating level;
see the table) until the device stops or switches off (a STOP or OFF command is automatically trans-
mitted every 1.5 seconds).
Then release the search key and press the Select key to save the code which was found.
Reset:
Proceed as described above for entering the codes for VCR, DVD, CD, tuner, tape as far as the step
where the code number is entered. Then enter "000" for the reset function. The LED blinks 2x to
acknowledge the input. All codes are now reset to the factory default settings.
The reset is executed for all operating levels, regardless of the level from which it is initiated.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation without the remote control
This operating mode is provided only for situa-
tions where, for example, the batteries in your
remote control are flat or you cannot find the
remote control.
The local controls are located on the front of
the tuner box.
ꢀ
Switching on
Press the power switch ቢ on the tuner box to
switch to standby mode. Switch on the plasma
monitor with the power switch. The LEDs on both
units light red. The press the "P+" or "P–" key ቤ
to switch the TV set on. Both LEDs change to
green.
Adjusting the volume:
Press key ባ, „z +“ or „z –“
.
Selecting stations:
Press key ቤ, "P+" or "P–".
Opening the menu:
Press key ብ "M". Then use the keys "P+" , "P–" ,
„z +“ and "Volume –" to navigate in the menu.
TV/AV:
The key "AV" ብ is used to switch between TV
mode and AV mode.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Selecting your country
Open the menu
Once you have installed the TV set, you must spe-
cify the country in which it is located (e.g. UK) to
assign certain basic settings (such as the TV chan-
nel frequencies).
Selecting your country:
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu "Set-
tings".
MENU
• Use the cursor key ꢁ to select the menu item
"TV tuner" and press the "OK" key to open it.
• Use the cursor key ꢂ ̈ to select the sub-menu
"APS".
• Use the cursor key ̈ to select the menu item
"Country".
OK
• Use the cursor keyꢂ ̈ to select the desired
country from the list.
• Press the "TV" key to close the TV
menu.
aps
The setting is saved automati-
cally when you close the menu.
ꢀ
country
England
right / left to change country
TV
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
5.1 Selecting a language
Language selection for the TV menu
You can select any of the available languages for
the TV menu. All text in the menu and the help
screens (Information) are displayed in the selected
language.
Selecting the language:
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu
"Options".
• Use the cursor key ꢁ to select the menu item
"Language".
• Use the cursor key ꢂ ̈ to select one of the
languages from the list.
MENU
OK
• Press the "TV" key to close the TV menu.
The setting is saved automati-
cally when you close the TV
menu.
ꢀ
options
language
english
osd timeout
menu backround
scart 2 out
FAV
scart 4 out
Scart 3
sleep timer
<ok> to set sleep time
sleep time remaining
right / left to change language
TV
70
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Tuning to TV stations
Open the menu
You can tune your TV set to TV stations in three
different ways:
a) Automatic Programme Search (APS)
The automatic programme search searches the
entire range of channels for TV stations. All sta-
tions which are found are placed in a station table
which is displayed at the end of the search. If you
do not like the order in which the stations appear
in this table, you can move stations to other posi-
tions and/or delete unwanted stations. For further
details, see Section 9, "Sorting the stations".
MENU
Executing an automatic programme search
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu
"Settings".
• Use the cursor key ꢁ to select the menu item
"TV tuner".
OK
• Press the "OK" key and open the sub-menu
"Programming".
• Use the cursor key ̈ to open the
sub-menu "APS".
• Use the cursor key ꢁ to select the
menu item "Auto setting".
aps
• Press the "OK" key. You are then
asked if you really want to start the
programme search.
autoset
<ok> to enable
• Press the "OK" key again to start
the search..
• A station table containing the
results of the search is displayed.
<ok> to start aps function
• You can delete any unwanted sta-
tions from the table by selecting them with the
cursor key and pressing the red key.
The settings are saved automatically when
you close the TV menu.
ꢀ
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
6. Tuning to TV stations
b) Manual search
You can use the manual search function to search
for individual stations whose channel number or
frequency you do not know.
Executing a manual search
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu "Set-
tings".
• Use the cursor key ꢁ to select the menu item
"TV tuner".
• Press the "OK" key and open the sub-menu
"Programming".
MENU
OK
• Use the cursor key ꢁ to select the menu item
"Manual search".
• Use the cursor key ̈ to start the
search.
• The search halts when a station is
found.
programming
• If you wish to save this station, use
the cursor key ꢀ to select the menu
item "Save programme".
• Use the cursor key ꢂ ̈ to save the
station which was found.
manual search
• Press the "TV" key to close the TV
menu.
right / left to search
You can change the station
logo: see Section 6.1.
ꢀ
TV
72
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Tuning to TV stations
Open the menu
c) Direct channel input
If you know the channel number of a station you
want to save, you can enter this number directly.
Executing direct channel input
• Press the "MENU" key to open the TV menu.
MENU
• Use the cursor key ̈ to select the menu "Set-
tings".
• Use the cursor key ꢁ to select the menu item
"TV tuner".
OK
• Press the "OK" key and open the sub-menu
"Programming".
• Use the cursor key ꢁ to select the
menu item "Channel type".
• Use the cursor key ̈ to set the
desired channel type (C = normal
channel / S = special channel).
programming
• Use the cursor key ꢀ to select the
menu item "Channel" and enter
the channel number with the
numeric keys.
channel
channel type
C
S
• Use the cursor key ꢁ to select the
menu item "Save programme".
• Use the cursor key ꢂ ̈ to save the
entered station.
right / left to change channel
• Press the "TV" key to close the TV menu.
You can change the station logo:
see Section 6.1.
ꢀ
TV
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
6. Tuning to TV stations
Fine tuning
The TV set is normally tuned to the centre frequency
of each of the TV channels. This is usually satisfac-
tory. If you are not satisfied, you can carry out fine
tuning of the frequency.
MENU
Executing fine tuning
• Switch to the programme position you wish to
adjust.
• Press the "MENU" key to open the TV menu.
OK
• Use the cursor key ̈ to select the menu item
"Settings".
• Use the cursor key ꢁ to select the
menu item "TV tuner".
• Press the "OK" key and open the
sub-menu "Programming".
• Use the cursor key ꢁ to select the
menu item "Fine tuning".
programming
fine tune
• Use the cursor key ꢂ ̈ to carry
out fine tuning.
• If you want to save the fine-tuning
setting, use the cursor key ꢁ to
select the menu item "Store pro-
gram".
right / left to adjust fine tuning
TV
• Then press the cursor keys ꢂ ̈ to save the set-
ting.
• Press the "TV" key to close the TV menu.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 Station logo
Open the menu
Each station which transmits VPS signals automati-
cally receives a station logo with up to four cha-
racters. If this automatic assignment does not
work, or if you want a different logo, you can
enter the logo manually.
Setting the station logo
INFO
• Switch to the programme position for which you
want to set the logo.
• Press the "INFO" key.
• Press the yellow key and switch to edit mode.
• You can either delete the entire station logo with
the "AV" key or use the cursor key ꢂ ̈ to select
the individual characters of the logo and then
use the cursor key ꢀ ꢁ to change these charac-
ters.
OK
• Press the "TV" key to close the TV menu.
The setting is saved automatically when you
close the TV menu.
ꢀ
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
6.2 Sorting the stations
In the station table, you can shift or delete indivi-
dual stations.
Shifting and deleting stations
• Press the "INFO" key to open the station table.
INFO
• Use the cursor key ꢂ ̈ ꢀ ꢁ to select the station
you want to shift or delete.
• To delete this station, press the red key and, in
the menu, press the "OK" key to confirm that
you want to delete it.
• To move the selected station, press the green
key. The frame around the selected station chan-
ges from red to yellow, indicating
OK
program table
that it can be moved.
• Use the cursor key ꢂ ̈ ꢀ ꢁ to
move the station logo in the yel-
low frame to the new position.
• Press the green key to insert the
station at this position.
All other programme posi-
tions are shifted as necessary
to make space for the inser-
ted station!
ꢀ
Delete
Insert
Name
• Press the "TV" key to close the
station table.
TV
76
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Programme selection
Programme selection and programme-
position management
Your TV set can manage a maximum of 100 pro-
gramme positions (0-99) in the station table. You
can select these programme positions with the
numeric keys, the "P+/P-" keys or from the sta-
tion table.
When you press a numeric key, you have three
seconds to enter any further digits.
P+
P–
Programme selection from the station
table
In normal TV mode, you can open the station
table by pressing the "INFO" key. In the table
which is then displayed, you can use the cursor
key ꢂ ̈ ꢀ ꢁ to select a programme. The selected
programme is then displayed on the screen.
INFO
Back to the previous programme
You can switch back and forth between the last
two selected programme positions with the
key.
OK
Example:
You are currently watching ITV. During the com-
mercials, you switch to BBC with the numeric keys.
You can now switch back and forth between BBC
and ITV with the
key.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
8. Picture settings
The picture settings (brightness, contrast, sharp-
ness, etc.) can be set globally for all programme
positions.
Adjusting the picture settings:
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu
"Picture".
MENU
• Use the cursor key ꢁ to select the desired menu
item "Brightness", "Contrast", "Sharpness" or
"Colour".
• Use the cursor key ꢂ ̈ to adjust the selected
picture setting.
OK
• Press the "TV" key to close the TV menu.
The settings are saved automatically when
you close the TV menu.
ꢀ
picture
brightness
right / left to adjust brightness
TV
78
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Sound settings
Open the menu
The sound settings (volume, headphone volume,
balance, etc.) can be adjusted in the menu
"Audio".
Adjusting the sound settings:
• Press the "MENU" key to open the TV menu.
MENU
• Use the cursor key ̈ to select the menu
"Audio".
• Use the cursor key ꢁ to select the desired sound
setting Volume, Headphone volume, Headphone
sound mode, Balance, Equalizer or Subwoofer.
OK
• Use the cursor key ꢂ ̈ to adjust the selected
setting.
• Press the "TV" key to close the TV
menu.
audio
The settings are saved automa-
tically when you close the TV
menu.
ꢀ
Subwoofer
subwoofer
You can connect an active subwoofer
to the socket on the rear of the tuner
box for better bass reproduction.
After connecting the subwoofer, set
the corresponding menu item to
"ON".
down for audio adjustments
Equalizer settings:
The equalizer offers the standard settings "Nor-
mal", "Pop", "Rock", "Jazz" and "Classical".
If you are not satisfied with these standard set-
tings, you can configure your own personal set-
ting under "User".
79
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Special functions
Picture in Picture (PIP)
Open the menu
The PIP picture can be used to display the pro-
gramme of a second TV station or a signal from
an AV device.
Displaying/hiding PIP:
• Press the red key to display the PIP picture.
• You can use the cursor key ꢀ ꢁ to select the
content of the picture + the selected part of the
picture is surrounded by a green frame.
• You can use the numeric keys or the "P+/P-"
keys to switch to another programme position in
the PIP picture.
OK
• You can display a signal from an AV device
(such as video recorder or camera)
in the PIP picture by pressing the
"AV" key several times.
• You can zoom the PIP picture in
eight steps. To do this, press the
yellow key and then use the cur-
sor key ꢂ ̈ to increase or decre-
ase the size of the PIP picture.
• You can move the PIP picture to a
different position on the screen.
To do this, press the green key
and then use the cursor key ꢂ ̈
to move the PIP picture.
• You can exchange the contents of the PIP picture
and the main picture by pressing the white key..
• To hide the PIP picture, press the red key again.
Any changes you have made to the PIP set-
tings are saved automatically when you
hide the PIP picture.
ꢀ
80
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Special functions
Picture size
Open the menu
You can use the function "Picture size " to adjust
programmes transmitted in various formats to
match the wide-screen format of the TV screen.
Adjusting the picture-size:
• Press the
key. The current aspect ratio is
displayed at the bottom of the screen.
• Use the cursor key ꢂ ̈ to select the desired set-
ting. The available options are:
OK
or use the menu "Window"
Possible picture-size settings:
Normal:
Programmes are displayed in the standard format 4:3.
Auto: (preferred setting)
The picture is always displayed with the correct aspect ratio (4:3 or 16:9), depending
on the input signal. In TV mode, the "Wide Screen Signal" (WSS) is evaluated: if the
station does not transmit the WSS signal, the picture is displayed as if the option "Fill
screen" were selected.
Fill screen:
Regardless of the transmitted aspect ratio, the picture always fills the full width of the
screen.
16:9:
Picture signals in the 16:9 aspect ratio are expanded to fill the full height of the
screen, leaving only narrow black stripes at the sides.
Tip: You can use this setting to magnify pictures received in the aspect ratio 4:3. Only
a small part of the picture is lost at the top and bottom of the screen.
Letterbox:
This option can be used to expand the picture vertically so that programmes with a
black stripe at the top and bottom fill the screen.
Subtitles:
The picture is zoomed and moved slightly upwards so that the subtitles are easier to
read.
The setting is saved automatically when you close the TV menu.
ꢀ
81
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Special functions
Split screen
In "split screen" mode, the screen is divided verti-
cally into two halves.
You can activate and deactivate this mode with the
key.
When this mode is activated, you hear
the sound belonging to the picture on the
left.
You can use the cursor keys ꢀ ꢁ to select
the pictures. The selected picture then has
a green frame for a short time. You can
now change the source of this picture
with the numeric keys, with the "P+/P-"
keys or the "AV" key. You can also per-
form picture settings (see Section 8).
You then hear the sound of the selected
picture.
When you deactivate this mode with the
key,
the TV set is always switched to the station display-
ed on the left.
The settings are saved automatically when
you deactivate this function.
ꢀ
10. Special functions
Freeze frame
Pressing the "OK" key immediately freezes the pic-
ture on the screen. The programme (or video film)
continues to run in the background.
OK
Press the "OK" key again to switch back to the cur-
rent programme (or video film).
82
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Special functions
Sleep timer
Open the menu
By programming the sleep timer, you can determi-
ne when the TV set is to switch itself off automati-
cally.
MENU
The sleep timer can be set to Off, 30, 60, 90 or
120 minutes.
Setting the sleep timer:
• Press the "MENU" key to open the TV menu.
OK
• Use the cursor key ̈ to select the
menu "Options".
• Use the cursor key ꢁ to select the
options
menu item "Sleep timer".
language
• Use the cursor key ꢂ ̈ to set the
osd timeout
desired time after which the TV set is
menu backround
to switch itself off.
FAV
Scart 3
<ok> to set sleep time
scart 2 out
scart 4 out
sleeptimer
sleep time remaining
• Press the "TV" key to close the TV
menu.
30 minutes
The setting is saved automatical-
ly when you close the TV menu.
ꢀ
adjust sleeptimer
TV
10. Special functions
Display the time
If you are watching a station which transmits Tele-
text, you can display the current time by pressing
the
key.
Ȅ
Ȅ
The time cannot be displayed when you are wat-
ching a station which does not transmit Teletext.
The time display disappears automatically after
about four seconds.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
11. Teletext
Teletext is an additional, free information servi-
ce which is provided by many TV stations. You
can scroll through the pages of this "electronic
newspaper" in various ways.
i
Displaying Teletext:
• Press the "TEXT" key.
Page 100 (Contents page) of the Teletext is
displayed on the screen.
TEXT
Navigating through Teletext with
pages displayed:
• You can step through the subjects by pressing
the blue key.
• You can step through the sections of a subject by
pressing the yellow key.
• You can step backwards through the Teletext
pages by pressing the red key.
• You can step forwards through the Teletext
pages by pressing the green key.
To select a specific page, enter the page number
with the numeric keys.
Sub-pages are automatically scrolled.
Hiding Teletext:
• Press the "TV" key or the "TEXT" key.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Connecting headphones
The headphone socket is located on the front of
the tuner box.
We recommend that you use headphones with an
impedance of at least 32 Ω. If you use headpho-
nes with a lower impedance (approx. 8 Ω), the
dynamic range will be lower.
In the case of dual-language programmes, you
can listen to sound channel 1 or 2 on the head-
phones, regardless of which is selected for the
internal loudspeakers.
You can adjust the headphone sound settings in
the "Audio" menu (see Section 9).
Headphone socket
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the menu
13. AV devices
AV (Audio/Video) devices are external devices
(such as video recorders, DVD players, decoders,
video cameras, etc.) which generate picture and/or
sound signals and can be connected to a TV set.
AV
Video recorders, DVD players and similar devices
can be connected to the Scart 1 or Scart 2 socket.
Decoders must always be connected to the Scart 1
socket.
or
MENU
If an AV device connected to one of the Scart sok-
kets generates a suitable switching voltage, the TV
set automatically switches to AV mode when the
device is switched to playback mode (composite-
video signal).
OK
For AV devices connected to the front sockets, you
must switch the TV set to AV mode manually in
order to display their signals.
For AV devices connected to the front
sockets, you must switch the TV set to
AV mode manually in order to
display their signals.
settings
tuner
source select
Scart 1
Scart 1 RGB
Scart 2
Scart 2 RGB
Scart 3
Scart 4
BAV
Selecting AV mode manually
• Press the "AV" key several times to
step through the AV programme posi-
tions to the desired position
PC
- or -
right to select source
Ļ
• Press the "MENU" key to open the
TV menu.
• Use the cursor key ̈ to select the menu
"Settings".
• Use the cursor key ꢁ to select the menu item
"Select source".
• Press the "OK" key and open the sub-menu
"Select source".
• Use the cursor key ꢀ ꢁ to select the source (the
socket to which the desired AV device is connec-
ted).
• Use the cursor key ̈ to activate this source.
• Start the AV device in the desired mode.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV devices
Possible selections
• Tuner
The signal from the TV station to which the TV set
is tuned is displayed.
• Scart 1/2/3/4
The composite-colour signal (FBAS) from the AV
device connected to the corresponding Scart
socket is displayed.
• Scart 1/2 RGB
The RGB signal from the AV devi-
ce connected to the corresponding
Scart socket is displayed.
window
• PC und DVI
The picture from the connected PC
is displayed.
The picture size and position can
be adjusted in the menu
"Window".
down for size setting
The brightness, contrast and phase
(adjustment for picture sharpness,
executed automatically when a PC
is connected) can be adjusted in
the menu "Picture".
picture
• BAV (Back AV socket, in/out) on
the rear of the tuner box.
• FAV (front AV socket)
The picture from the AV device con-
nected to the front AV socket is
down for picture settings for current window
displayed in the composite-colour picture signal.
• S-Video
The picture from the AV device connected to the
front AV socket is displayed in the S-Video (YC)
picture signal.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Copying AV recordings
Open the menu
Your TV set has a copy mode in which an AV devi-
ce connected to the Scart 2 socket can record the
picture and sound coming from an AV device con-
nected to the "FAV" (Front AV socket) or to the
Scart 1 socket.
Selecting the Scart 2 socket as the output:
• Press the "MENU" key to open the TV menu.
• Use the cursor key ̈ to select the menu
"Options".
MENU
• Use the cursor key ꢁ to select the menu item
"Scart 2 output".
• Use the cursor key ꢂ ̈ to select the socket to
which the device being used for playback is con-
nected.
OK
• Switch the recording device to
record mode and then press "Play"
on the playback device.
• Press the "TV" key to close the TV
menu.
options
osd timeout
menu backround
scart 2 out
scart 4 out
The settings are saved automa-
tically when you close the TV
menu.
ꢀ
FAV
Scart 3
<ok> to set sleep time
sleep timer
sleep time remaining
right / left to select scart 2 out
TV
88
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV devices
Open the menu
Picture quality when playing back pictu-
res from tape
MENU
The VCR function ensures an optimal picture quali-
ty when playing back recordings from tape devices
such as camcorders or video recorders.
The VCR function in the menu "Options" can
be selected only if, for example, the connec-
ted video recorder is delivering a signal.
ꢀ
OK
Activating the VCR function
• Start the playback function on the
AV device.
• Press the "MENU" key to open the
TV menu.
options
• Use the cursor key ̈ to select the
vcr
on
menu "Options".
osd timeout
menu backround
scart 2 out
• Use the cursor key ꢁ to select the
menu item "vcr".
FAV
Scart 3
scart 4 out
sleep timer
sleep time remaining
<ok> to set sleep time
• Use the cursor key ꢂ ̈ to switch
the function on or off.
right / left to change vcr status
• Press the "TV" key to close the TV
menu.
The setting is saved automatically when you
close the TV menu.
ꢀ
89
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV devices - PC
Connecting the PC via VGA input
Power off both computer and TV before making
any connections.
Connect the VGA cable to the VGA input of your
TV and to the 15-pin connector on the rear of your
computer.
Tighten the screws on the plugs until the connectors
are fastened securely.
If you are using Windows operating system run-
ning on a PC with a Microsoft Plug & Play compati-
ble video card, your system will select the appro-
priate timing for your monitor.
Connecting the PC via DVI
(Digital Video Interface) input
To get the best possible picture quality you’ll need
to use the DVI sockets on both the TV and your PC.
This allows the PC to send a pure digital signal
straight from the graphics card to the TFT TV. As
DVI-I type socket exists on the TFT TV, use a DVI-D
or DVI-I cable for connection.
DDC (Display Date Channel) and EDID (Extended
Display Identification Data), which are used for
Plug & Play compatibility, are supported.
Hot Plug Detection is not supported.
Low refresh rates like 60Hz and 72Hz should be
used and native resolution should be preferred.
The DVI interface does not support HDCP (High
bandwidth Digital Content Protection), therefore a
HDCP DVD player could not be used.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
13. AV devices - PC
PC input typical display modes
The display has a maximum resolution of 1280 x
768, vertical sync. frequency range of 50-75Hz
and a horizontal sync. frequency range of 30-
69Hz.
The following table is an illustration of some of the
typical video display modes.
The native resolution of the TFT-LCD Panel is 1280
x 768. Therefore using Mode 14’ is advised to get
the best PC input display quality.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Cleaning the set
Before cleaning the set, always switch it off
with the mains switch!
ꢀ
ꢀ
Incorrect treatment and cleaning of the
screen surface can cause irreparable dama-
ge to it. You should therefore always obser-
ve the following instructions for treatment
and cleaning of the set.
Treatment:
Always treat the screen surface very carefully.
Take care not to damage it mechanically by
shocks, impact, scratching or scraping.
Keep sharp, pointed and hard objects away from
the surface of the screen.
Keep the surface of the screen clean.
For cleaning the case and the screen, use only a
soft, dry cloth. For removing stubborn marks, you
may moisten the cloth slightly.
Cleaning and care:
Always switch off the TV set and remove the
mains plug from the wall outlet before cleaning.
The surface of the screen may be cleaned only
with a soft, dry cloth (such as a microfleece
duster). If any marks cannot be removed with this
dry cloth, you may moisten the cloth slightly.
Take care that no water or other liquid can enter
the TV set, since this can cause serious damage to
the set.
If any liquid or other foreign object (pieces of
metal, etc.) enters the set, immediately disconnect
the mains plug from the wall outlet.
Never insert your hands or tools into the set, since
this may result in electric shocks.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Technical data
Mains voltage:
220 - 240 V
50 Hz
˜
Antenna input:
75 Ohms asymmetrical
DIN 45325
Tuning range:
Standard channels 2 - 12, 21 - 69
Special channels S1 - S20, S21 - S41
S42 ... S46 (Belgium: channels OIR)
Power
consumption:
Plasma monitor
and tuner box
2 x 14 W
(2 x 8 W)
ca. 355 W
Energy consumption per hour (Wh):
See power consumption in W multiplied by 1 hour
Standby
Plasma monitor:
Tuner box:
approx. 3 Wh
approx. 7 Wh
Dimensions:
Plasma monitor with stand (H x D x W)
717 mm x 340 mm x 1049 mm
Width with loudspeakers attached: 1295 mm
Errors excepted. Subject to changes !
93
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Disposal of batteries
Dry or rechargeable batteries should never be
discarded as normal garbage!
Please use the local facilities for the disposal of
exhausted batteries.
Make sure the batteries are fully discharged befo-
re disposal.
The batteries are generally fully discharged when
the unit in which they are used
- switches itself off or indicates "Battery flat"
or
- no longer operates correctly when the batteries
have been in use for a long time.
In order to avoid short-circuits, the poles of the
batteries should be covered with a piece of adhe-
sive tape.
Batteries which contain dangerous substances are
marked as follows:
Pb = battery contains lead
Cd = battery contains cadmium
Hg = battery contains mercury
Li = battery contains lithium
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible cause
Remedies
• Remove the obstacle.
The plasma monitor • There is an obstacle between
does not react to
commands from the
remote control.
the remote control and the
plasma monitor.
• Sunlight is shining directly on
the infrared sensor in the plas-
ma monitor.
• Ensure that the sun does
not shine on the set.
• The batteries in the remote
control are flat.
• Install new batteries.
• Switch on the plasma
monitor set with the
main switch.
• The plasma monitor is not swit-
ched on with the main switch.
• Switch the plasma moni-
tor set off with the main
switch, wait a few
• Fault in the internal processor.
seconds and then switch
it on again.
• The LVDS cable between the
plasma monitor and the tuner
box is not connected correctly.
• Check the connection.
Your Metz product was developed and
manufactured with high-quality materials
and components which can be recycled
and/or re-used.
This symbol indicates that electrical and
electronic equipment must be disposed of
separately from normal garbage at the
end of its operational lifetime.
Please dispose of this product by bringing
it to your local collection point or recy-
cling centre for such equipment.
This will help to protect the environment in
which we all live.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
BLACK PANTHER
616
491
508
607
614
466
505
Codes Video
BLAUPUNKT
496
527
609
621
487
502
530
610
507
532
612
Metz VG61
532
VF21, VF44, VF46
VF61, VE21, VE43
VE44, VE45, VD21
VD43, VD44, VD45
VC21, VC43, VC44
VC62, 21VB11
BONDSTEC
BONDSTECBRANDT
BRANDT ELECTRONIQUE 503
574
504
505
524
BRAUN
570
450
481
466
588
BRIONVEGA
BROKSONIC
BRUNS
575
42VB12, 21VA12
21VA13, 42VA11
64VA14, 9836,9837
9847, 9874, 9875
9876, 9877
487
590
490
593
BUSH
CALIN
481
481
481
547
527
505
487
487
606
481
466
547
487
466
CALIX
CANDLE
CARRERA
CARVER
CGE
Metz VF22, VF47
VF48, 9843, 9844
9849
568
573
CIE
CIMLINE
CLARIVOX
CLASSIC
CLATRONIC
COLORTYME
COLT
481
487
547
Metz VH22, VH47
VH48
ACTION
ADMIRAL
ADVANTZ
ADVENTURA
ADYSON
AGHA
468
481
481
468
487
547
481
477
481
505
575
487
487
466
547
529
529
487
575
478
575
481
481
527
528
505
575
466
481
487
481
487
547
547
562
CONDOR
616
504
487
507
481
CONTINENTAL EDISON 503
505
547
527
CRAIG
481
481
487
490
575
466
505
547
CROSLEY
CROWN
CROWN
CRYSTAL
CTC
547
616
AIWA
505
572
575
616
AKAI
482
508
609
483
546
612
484
554
CURTIS MATHES
CYBEREX
547
468
AKIBA
AKURA
505
588
DAEWOO
DANSAI
DAWA
DAYTRON
DE GRAAF
DECCA
DECCAVIDEO
DENON
DIGITAL
DORIC
466
487
575
466
529
528
528
527
477
601
547
503
530
505
468
487
553
ALBA
593
ALLORGAN
ALLSTAR
AMWAY
ANITECH
ART TECH
ASA
490
481
529
528
ASBERG
ASTRA
481
504
481
505
505
487
547
487
ASUKA
DTS
DUAL
ASUKA
527
527
ASWO
AUDIO DYNAMICS
AUDIOSONIC
AUDIOTON
AUDIOVOX
AVIS
DUEL
DUMONT
DYNATECH
616
547
583
ECONOMIC
510
487
616
487
481
481
547
487
481
EDISON
BAIRD
505
503
487
513
607
547
468
466
ELBE
BANG & OLUFSEN
BASIC LINE
BAUR
ELCATECH
ELECTROHOME
ELECTROPHONIC
ELIN
547
616
547
609
565
612
599
BEAUMARK
BELL & HOWELL
BESTAR
ELTA
EMERSON
616
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
EPC
505
466
487
586
604
586
510
598
616
JENSEN
JETPOINT
JVC
505
575
503
520
515
ESC
ETZUKO
EUROPHON
EXPERT
504
545
521
505
603
519
JVC_LCD
FERGUSON
501
555
487
468
477
468
481
505
574
523
595
524
596
KAISER
KAISUI
KAPSCH
KARCHER
KENDO
KENWOOD
KLH
575
487
600
575
483
468
481
487
481
487
473
FIDELITY
FINLUX
FIRST LINE
FISHER
601
477
481
473
487
478
487
528
575
505
487
FUNAI
571
KLIT
GAB
487
466
547
528
466
575
487
468
556
466
617
468
468
542
601
481
451
457
461
491
496
530
585
610
602
KODAK
KORPEL
KUBA
GBC
GE
504
505
547
510
517
GEC
601
603
604
GELOSO
GITEM
GOLDHAND
GOLDSTAR
LEYCO
487
578
575
481
601
481
481
487
468
518
468
LG
490
481
575
487
621
505
474
557
605
487
452
458
462
492
497
531
600
611
LIESENKOTTER
LLOYD
565
487
606
491
491
509
478
601
477
547
610
530
552
616
LLOYD’S
LOEWE
LOEWE OPTA
LOGIK
GOODMANS
575
527
547
483
GRAETZ
GRANADA
600
477
565
606
604
453
459
463
493
507
563
606
612
603
532
575
616
LUXOR
LXI
481
GRANDIN
GRUNDIG
MAGNADYNE
M ELECTRONICS
MAGNASONIC
MAGNAVOX
MAGNIN
MAGNUM
MANESTH
MARANTZ
MARQUANT
MARTA
575
547
470
481
481
581
487
491
487
481
481
486
562
527
527
468
487
547
547
606
477
477
542
487
481
466
601
454
460
464
495
527
584
609
613
481
507
547
582
487
527
547
547
GRUNDIG
528
490
565
566
GUTTRONIC
HANSEATIC
HANTAREX
HARLEY DAVIDSON
HARVARD
HCM
HEADQUARTER
HINARI
481
575
481
481
466
468
487
475
481
530
604
487
575
MATRIX
MATSUI
509
586
560
601
561
610
487
487
MATSUSHITA
MEDIATOR
MEMOREX
MEMPHIS
MGA
490
481
547
509
476
485
535
HINARIHITACHI
HITACHI
477
503
601
478
505
603
MGN
MINERVA
MINOLTA
MITSUBISHI
609
610
612
527
477
575
HYPSON
505
609
547
519
612
468
IMPERIAL
510
509
510
616
481
575
468
600
466
487
481
450
466
575
547
487
INGERSOL
INNO HIT
575
MULTITECH
MURPHY
481
487
INNO HIT
INTERBUY
INTERDISCOUNT
INTERFUNK
NAD
547
507
504
450
491
509
519
527
601
565
603
575
604
NATIONAL
NEC
505
469
493
510
528
576
470
496
512
541
INTERVIDEO
INTERVISION
IRRADIO
ITT
NECKERMANN
477
505
513
565
487
468
481
575
483
606
505
ITV
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
575
575
487
466
481
606
450
488
505
518
554
601
500
515
602
575
610
611
616
QUELLE
478
496
505
512
529
599
610
616
466
484
497
508
513
541
604
611
621
487
503
509
519
565
606
612
491
504
510
528
575
609
614
NEI
NESCO
NIKKAI
NIKKO
NOBLIKO
NOKIA
468
489
510
547
557
603
503
521
470
503
516
551
567
604
504
524
483
504
517
553
600
QUESTAR
RADIALVA
RADIOLA
RADIONETTE
RADIX
RANDEX
RANDIU
481
527
601
497
481
481
601
477
468
601
503
481
481
466
487
575
604
527
505
574
NOVATRONIC
RANK/BUSH/MURPHY
RCA
OCEANIC
OKANO
OLYMPIC
OLYMPUS
ORION
483
487
466
507
481
537
560
527
508
544
609
616
489
601
604
481
481
483
547
547
617
REALISTIC
REDIFFUSION
REX
505
509
538
561
474
512
565
610
620
531
558
589
493
513
575
611
621
536
559
591
496
541
599
612
RICOH
ROADSTAR
ROYAL
487
487
547
OTTO VERSAND
SABA
499
515
574
486
467
516
606
547
510
597
487
487
509
468
551
527
450
477
510
563
573
582
481
468
487
509
503
466
466
468
487
481
547
509
609
459
468
479
491
503
521
601
509
468
517
504
524
603
575
470
505
540
SABA
SABA
SAISHO
SALORA
SALORA
SAMBERS
SAMEX
SAMSUNG
483
575
PAEL
606
481
507
533
623
503
547
477
477
606
481
481
529
550
568
624
491
527
481
477
505
487
547
477
487
481
468
565
PALLADIUM
PANASONIC
487
508
549
491
527
600
505
532
601
547
575
575
PATHE MARCONI
PAXSONIX
PENNEY
PENTAX
PERSHIN
PHILCO
505
481
SANKY
SANSUI
SANWA
SANYO
505
527
547
469
577
470
586
471
507
491
530
563
575
625
565
527
507
547
564
620
547
528
548
565
621
SBR
PHILIPS
SCHAUB LORENZ
SCHNEIDER
468
478
527
564
575
604
483
481
529
569
578
505
487
530
571
581
PHILIPS
PHILIPS
PHILIPS
PHILIPS
PHILIPS (F)
PHONOLA
PILOT
575
SCOTT
SEARS
477
490
528
504
481
510
PIONEER
PRIMA
527
547
490
539
529
483
575
547
SEG
547
545
SEI-SINUDYNE
SELECO
SENTRA
SETRON
SHARP
PROFEX
PROFILE
PROSCAN
PROTEC
PULSAR
PULSER
505
481
487
544
547
481
575
SHINTOM
SHIVAKI
SHOGUN
SHORAI
SICE
547
575
PYE
QTY1
592
468
481
507
450
470
612
461
469
480
492
QUARTER
QUARTZ
QUASAR
QUELLE
SIEMENS
462
470
481
493
464
472
486
494
547
527
459
471
461
474
464
477
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
SIEMENS
495
511
607
612
575
481
487
509
599
466
575
601
481
506
541
547
477
487
527
481
496
525
609
614
497
530
610
498
584
611
TRIAD
TRIX
575
481
466
TVA
UHER
466
505
450
565
606
547
560
481
530
606
604
477
510
616
575
609
481
543
503
SILMA
SILVA
SINGER
SINUDYNE
ULTRAVOX
UMA
UMA
547
513
575
527
616
575
601
612
604
614
UNITECH
UNITED
UNIVERSUM
SOLAVOX
SONOKO
SONOLOR
SONTEC
SONY
604
483
547
609
491
571
612
527
575
621
512
599
513
623
514
UNIVOX
VICTOR
505
466
554
547
481
481
545
562
SR1000
STS
SUNWOOD
SYLVANIA
SYMPHONIC
VIDEOMASTER
VIDEOPLUS
VIDEOSONIC
VIEWMARK
VIEWMAX
589
547
487
612
527
TAISHO
509
609
623
468
528
505
505
466
487
527
575
563
575
481
503
505
500
515
579
547
505
609
487
487
481
575
547
499
505
60
474
505
586
612
501
575
609
481
474
547
481
487
487
WARDS
477
575
481
487
565
TALENT
WEGAVOX
WELTBLICK
TANDBERG
TANDY
WHITE WESTINGHOUSE 450
TASHIKO
TATUNG
TEAC
529
527
WINSTON
WIZJA
WORLDVIEW
575
528
575
TEC
TECHLINE
TECHNICS
TECHNILAND
TECHNISAT
TEKNANT
TEKNIKA
TELEAVIA
TELEAVIA
TELEFUNKEN
XR1000
487
547
532
YAMISHI
YOKAN
YOKO
487
487
466
510
481
547
487
490
ZENITH
481
503
521
594
504
524
505
574
Codes DVD-Player
TELEORDER
TELERENT
TELESERVICE
TELETECH
TENOSAL
TENSAI
METZ
204
214
239
230
AKAI
612
BLUEsky
254
256
Boxford
487
593
490
509
CYBER HOME
223
247
Cytron
THOMAS
THOMSON
DENON
216
243
248
500
524
6226
482
542
604
503
574
504
594
D-i-K
DUAL
THORN
501
565
606
503
575
609
EMERSON
263
GAME
253
262
255
222
GOLDSTAR
GRAND PRIX
GRUNDIG
THORN-FERGUSON
503
601
612
487
481
504
604
505
606
232
210
238
260
HARMAN/KARDON
206
205
HITACHI
261
263
TOKAI
TOSHIBA
505
527
JVC
212
KENWOOD
208
270
246
231
TOTEVISION
TOWADA
TOWIKA
547
490
KISS
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
DIORA
DUAL
949
822
LABWAVE
LG
200
263
215
219
201
832
831
859
920
994
953
LINN
FISCHER
830
LOEWE
MARANTZ
218
271
241
221
240
256
269
219
272
236
258
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
885
872
888
908
MbyN
MEDIENCOM
MEDION
MEGATON
MUSTEK
228
257
911
931
912
934
913
935
HARMAN KARDON
905
853
MYRYAD
HITACHI
NAD
207
228
INTERSOUND
960
937
NONAME
ITT
ONKYO
209
266
225
267
226
274
ORION
JVC
844
903
848
904
849
992
902
PANASONIC
216
276
219
234
278
203
251
228
275
PHILIPS
220
235
227
236
233
237
KENWOOD
820
877
948
908
847
878
963
858
879
859
925
PIONEER
PROLINE
204
249
250
KRELL
273
268
LINN
908
924
964
946
LUXMAN
967
SAMSUNG
SCHAUB LORENZ
SCHNEIDER
SEG
210
255
244
201
224
243
211
242
METZ HE11
MARANTZ
MATSUI
882
833
908
955
908
908
908
972
908
955
248
263
229
263
264
908
909
SHERWOOD
SILVA SCHNEIDER
SONY
MEDION
MERIDIAN
MAGNAVOX
MICROMEGA
MINOWA
MISSION
MTC
265
SUNKAI
TECHNICS
216
228
213
202
217
259
277
245
TEVION
THOMSON
TOSHIBA
246
266
234
UNITED
252
216
255
278
NAD
947
908
930
938
888
802
806
NAIM
YAMAHA
NAKAMICHI
NOKIA
NONAME
NSM
Codes HIFI - CD
803
807
804
861
805
AIWA
815
856
856
957
929
908
909
816
857
817
872
884
921
AKAI
AKKAI
OKANO
869
819
871
827
AMSTARD
AMSTRAD
ARCAM
ASWO
ONKYO
881
870
911
940
976
942
956
PALLADIUM
PANASONIC
PHILIPS
810
834
833
965
824
862
923
906
908
851
915
908
866
918
909
BANG & OLUFSEN
BRAUN
BUSH
808
975
888
PIONEER
825
863
826
864
850
922
CAMBRIDGE
CAMBRIDGE AUDIO
CARVER
945
945
908
PMG
PROTON
QUAD
908
965
DAEWOO
876
801
853
961
DENON
812
899
962
845
900
846
901
RADIOTONE
958
911
RADMOR
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
REVOX
REVOX/STUDER
ROTEL
829
910
818
DENON
834
891
972
899
837
936
840
892
841
970
879
971
908
951
DIORA
DUAL
900
850
SABA
926
908
939
908
852
821
869
888
928
960
978
982
986
851
985
935
998
SAE
SAMSUNG
SANSUI
SANYO
SCHNEIDER
966
968
FISCHER
893
894
860
840
870
892
929
972
979
983
987
919
841
873
911
955
973
980
984
988
868
885
927
959
977
981
985
989
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
964
833
867
976
979
980
HARMAN KARDON
926
915
984
931
HITACHI
ITT
918
919
SHARP
SHERWOOD
SIEMENS
799
936
833
872
876
886
891
892
800
943
867
873
880
887
969
813
944
868
874
883
889
970
847
JVC
862
994
863
995
974
996
975
997
869
875
885
890
971
KENWOOD
848
957
917
958
935
990
936
993
SINOTEC
LINN
888
876
889
877
SINOTEC (PEPSI-DOSE) 892
LUXMAN
884
989
SONY
842
896
990
888
908
843
897
991
945
893
898
895
932
METZ HE11
961
887
MARANTZ
922
904
999
905
SUPERTECH
SYLVANIA
NAD
903
927
920
948
846
902
959
906
901
NAKAMICHI
NOKIA
T+A
882
974
T+A ELECTROAKUSTIK 882
OKANO
949
847
TECHNICS
809
950
954
823
916
993
917
918
ONKYO
856
TENSAI
THOMSON
ONKYO
960
PALLADIUM
PANASONIC
PHILIPS
944
928
921
853
938
943
UHER
814
869
966
995
929
976
854
939
988
982
980
855
941
UNIVERSUM
872
979
908
855
952
933
999
912
942
PIONEER
UNKNOWN
YAMAHA
828
941
854
RADMOR
978
860
977
REVOX
861
885
REVOX/STUDER
Codes HIFI - Tape
SAMSUNG
883
897
985
930
866
872
918
976
839
890
911
886
896
AIWA
AKAI
842
963
845
934
916
976
843
844
962
SANY
SANYO
SCHNEIDER
849
945
913
951
933
987
937
867
873
919
986
868
874
947
869
878
964
AMSTRAD
ASWO
BANG & OLUFSEN
BRAUN
BUSH
836
870
835
SHARP
SHERWOOD
864
908
923
993
909
910
DAEWOO
907
SIEMENS
880
881
882
946
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
947
953
964
865
967
992
950
954
976
925
968
951
955
952
956
NAD
459
419
748
NAKAMICHI
NONAME
SONY
965
969
966
991
OKANO
733
379
736
440
ONKYO
460
451
742
T+A
871
961
898
PALLADIUM
PANASONIC
PHILIPS
731
371
427
383
996
735
432
450
384
997
T+A ELEKTROAKUSTIK 961
TECHNICS
THOMSON
838
852
981
886
859
983
895
914
PIONEER
436
998
437
999
UNIVERSUM
868
947
875
950
REVOX
386
427
428
378
REVOX/STUDER
RADMOR
ROTEL
YAMAHA
857
924
858
932
Codes HIFI - Tuner
SAMSUNG
411
475
433
374
391
395
399
403
409
443
733
749
373
413
426
479
737
747
749
463
476
990
380
392
396
400
404
412
469
735
465
473
AIWA
376
734
452
469
744
427
377
737
455
745
993
464
SANYO
SCHNEIDER
995
388
393
397
401
407
441
470
746
AKAI
390
394
398
402
408
442
732
748
AMSTRAD
468
424
ASH
ASWO
BANG & OLUFSEN
369
748
BUSH
DAEWOO
458
371
445
461
370
739
372
471
SHARP
SHERWOOD
SIEMENS
446
456
427
480
738
DENON
423
991
457
477
732
739
478
733
746
DIORA
DUAL
381
449
994
FISCHER
434
SINOTEC
SINOTEC (PEPSI-DOSE) 749
GOLDSTAR
GOODMANNS
GOODMANS
GRUNDIG
746
737
748
427
SONY
389
422
466
416
420
431
421
462
SUPERTECH
T+A
429
450
405
743
430
HARMAN KARDON
418
453
730
991
T+A ELEKTROAKUSTIK 743
HITACHI
TECHNICS
TENSAI
THOMSON
387
406
382
ITT
412
JVC
414
448
425
444
446
447
740
UHER
375
403
737
UNIVERSUM
467
415
473
435
733
454
KENWOOD
417
741
439
994
YAMAHA
385
992
LINN
472
438
LUXMAN
474
Codes HIFI - Amp
METZ HE11
MARANTZ
MINOWA
MISSION
743
450
409
426
AIWA
777
753
785
840
776
793
985
754
813
986
766
829
AKAI
AMSTRAD
831
ASH
ASWO
NOKIA
410
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Code list
SAMSUNG
828
750
763
782
786
814
842
961
965
969
973
818
825
762
768
779
785
948
786
837
756
764
783
794
815
951
962
966
970
978
990
832
763
769
780
794
950
844
846
BANG & OLUFSEN
BRAUN
BUSH
996
960
748
SANYO
SCHNEIDER
768
784
812
827
953
963
967
971
779
785
813
840
956
964
968
972
782
DAEWOO
770
751
817
835
952
DENON
789
988
790
791
DIORA
DUAL
981
820
995
839
FISCHER
750
SHARP
SHERWOOD
SIEMENS
833
766
770
781
800
GRUNDIG
794
749
779
795
766
804
782
767
775
784
947
GOODMANNS
GOLDSTAR
HARMAN KARDON
760
751
823
HITACHI
SINOTEC
SINOTEC (PEPSI-DOSE) 786
ITT
827
SONY
SUPERTECH
787
782
788
974
836
991
976
JBL
821
792
975
816
JVC
819
818
T+A
774
959
806
T+A ELEKTROAKUSTIK 774
KENWOOD
755
771
TECHNICS
805
993
958
980
LINN
794
810
795
845
TENSAI
THOMSON
LUXMAN
954
798
955
METZ HE11
MARANTZ
MEDION
MERIDIAN
MINOWA
MISSION
774
794
785
795
978
799
UHER
987
763
963
795
UNIVERSUM
766
838
824
844
830
YAMAHA
752
809
979
NOKIA
NAD
NAKAMICHI
NIAM
NONAME
826
834
822
795
782
OKANO
763
772
765
982
ONKYO
PALLADIUM
761
783
991
PALLADIUM/OKANO 764
PANASONIC
PHILIPS
805
793
797
757
957
808
794
798
758
994
795
803
795
796
992
PIONEER
PRO-LOGIC
QUAD
795
RADIOTONE
841
801
843
796
983
RADMOR
802
977
797
984
803
798
REVOX
REVOX/STUDER
ROTEL
SABA
811
103
Download from Www.Somanuals.com. All Manuals Search And Download.
³
ᕢ
ᕣ
ᕤ
³
ᕢ
ᕣ
ᕤ
ᕥ
ᕦ
ᕧ
Service Center
Trainings Center
Verwaltung und Entwicklung
Lager/Versand
Mecablitz Produktion
TV Produktion
ᕥ
ᕧ
ᕦ
Kunststofftechnik
Metz - Werke GmbH & Co. KG - Zirndorf bei Nürnberg
Kernkompetenzen in den Bereichen Elektronik sowie Kunst-
stofftechnik bilden den Ursprung für den ausgezeichneten
Ruf der Metz-Werke. Er hat sich im Laufe vieler Jahrzehnte
weltweit aufgebaut.
Metz bietet Qualität Made in Germany:
Consumer Electronics, Photo Electronics, Kunststofftechnik.
Metz-Werke GmbH & Co. KG
Postfach 1267, D-90506 Zirndorf
Fon: +49 911 - 9706 0
Fax: +49 911 - 9706 340
www.metz.de
Technische Änderungen und Irrtümer
vorbehalten.
Errors excepted. Subject to changes.
Ķ ķ
Printed in Germany
Metz - allways first class.
Download from Www.Somanuals.com. All Manuals Search And Download.
|