INSTALLATION INSTRUCTIONS FOR PART 99-8214
APPLICATIONS
Toyota Tacoma 2005-2011
99-8214TB
99-8214TG
KIT FEATURES
• DIN Head Unit Provision With Pocket
• ISO DIN Head Unit Provision With Pocket
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
• Painted And Textured To Match Factory Dash
• Available In Two Colors:
99-8214TB = BLACK, 99-8214TG = GRAY
• Both kits are factory “golf ball” style
textured.
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets
• C) Radio Housing Trim Panel • D) ISO Brackets
• E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws
• G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket
E
B
A
I
G
F
C
D
H
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp interface harness 2003-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8214
TOYOTA TACOMA 2005-2011
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
TEXT
PWR VOL
2
3
4
Unclip and remove A/C control panel.
(Figure A)
SCAN
Remove (4) 10 MM bolts securing
radio. (Figure B)
Unclip and remove entire panel
including hazard switch and clock.
(Figure C)
5
6
Remove the left and right radio
brackets from the radio chassis.
(Figure D)
B
Unclip and remove the clock/hazard
switch assembly from the factory
radio housing trim panel. (Figure E)
Continue to Kit Preparation.
E
C
TEXT
PWR VOL
D
SCAN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT PREPARATION
99-8214
TACOMA 2005-2011
(SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO)
A
Attach the clock/hazard switch
bracket to the radio housing using
the (4) #6 x 3/8” Phillips pan head
screws.
WARNING:
DO NOT OVERTIGHTEN SCREWS.
1
2
Clip the clock/hazard switch
assembly into the 99-8214 Radio
Housing Trim Panel. (Figure A,B)
Continue to Kit Assembly.
PASSENGER
PASSENGER
H
M
INSERT CLOCK/HAZARD S
WITCH ASSEMBLY
FROM REAR OF 99-8214 R
ADIO HOUSING TRIM PAN
EL
B
PAS
P
ASSEN
H
SENGE
R
GER
M
2
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8214
TOYOTA TACOMA 2005-2011
DIN HEAD UNIT PROVISION
A
1
2
Attach the corresponding radio
housing bracket to the radio housing
using the included (4) #8 x 3/8”
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
3
4
Slide the aftermarket head unit into
the cage and secure. (Figure C)
B
Secure the Radio Housing into the
dash using the factory hardware.
Continue to Final Assembly.
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8214
TOYOTA TACOMA 2005-2011
ISO DIN HEAD UNIT PROVISION
A
1
Attach the corresponding radio
housing bracket to the radio housing
using the included (4) #8 x 3/8”
Phillips truss head screws.(Figure A)
2
3
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure B)
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
B
4
5
Snap the ISO Trim Plate into the
Radio Housing. (Figure C)
Secure the radio housing into the
dash using the factory hardware.
Continue to Final Assembly.
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8214
DOUBLE DIN HEAD UNIT PROVISION
A
1
Slide the aftermarket radio unit into
the factory brackets and secure the
unit to the brackets using the
screws supplied with the head unit.
(Figure A)
Secure the aftermarket radio unit
and factory bracket assembly into
the sub dash. (Figure B)
2
3
Place the Double DIN trim plate into
the back of the radio housing, then
B
attach the clock/hazard switch brack-
et assembly using the (4) #6 x 3/8”
Phillips pan head screws. (Figure C)
WARNING:
DO NOT OVERTIGHTEN SCREWS.
4
Clip the clock/hazard switch
assembly into the 99-8214 Radio
Housing Trim Panel. (Figure D)
Continue to Final Assembly.
D
C
REAR VIEW OF
RADIO HOUSING
REAR VIEW OF RADIO HOUSING
DOUBLE DIN TRIM PLATE
REMOVE
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
RESTORE
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
5
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8214
STACKED ISO DIN HEAD UNIT PROVISION
A
1
2
Slide the aftermarket radio units into
the factory brackets and secure the
unit to the brackets using the
screws supplied with the head unit.
(Figure A)
Secure the aftermarket radio units
and factory bracket assembly into
the sub dash. (Figure B)
3
Remove the (4) screws securing the
clock/hazard switch bracket to the
radio housing and remove the
clock/hazard switch bracket
assembly. (Figure C)
B
4
Place the Double DIN trim plate into
the radio housing and replace the
clock/hazard switch/bracket assem-
bly using the (4) #6 x 3/8” Phillips
pan head screws. (Figure D)
Continue to Final Assembly.
C
D
REAR VIEW OF
RADIO HOUSING
REAR VIEW OF RADIO HOUSING
DOUBLE DIN TRIM PLATE
REMOVE
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
RESTORE
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ASSEMBLY
99-8214
FINAL ASSEMBLY
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
A
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
B
C
D
Tape
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8214
NOTES
8
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8214
NOTES
9
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8214 INSTRUCTIONS
1-800-221-0932
REV. 11/22/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8214
Download from Www.Somanuals.com. All Manuals Search And Download.
|