Video Projector
MDLP1
Owner’s Manual
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
ADDITIONAL SAFETY INSTRUCTIONS!
CAUTION:
the projector’s lamp life timing system. The mercury
vapor gas inside the lamp bulb may be emitted from
the projector’s vent.
Before use, carefully read the projector Owner’s
Manual and the lamp replacement instructions. Re-
member to handle the lamp with care. In the event of
serious trouble, call a McIntosh Authorized Dealer.
1a. Do not directly expose skin to the light of the lamp
as it can cause inflamation.
The MDLP1 Video Projector weight is 40 pounds
(18.14 kilograms). When mounting the projector to a
building structure it is important to follow all of the
local building/constuction codes. Not evaluated for
Wall or Ceiling Mounting.
WARNINGS:
A. Do not remove the cover from the equipment.
B. Do not insert anything into the equipment through
the ventilation holes.
2b. Do not drop, impact, subject to excessive force or
otherwise damage the lamp.
C. Do not handle the mains lead with wet hands.
D. No naked flame sources, such as lighted candles,
should be placed on the equipment.
E. When disposing of used batteries and the projector
lamp, please comply with governmental regula-
tions or environmental public instructions rules
that apply in your country or area.
3c. Replacing the lamp runs the risk of burns, cuts
and electric shock, unplug the AC power cord
from the AC power outlet and wait at least 60
minutes for the lamp to cool down before attempt-
ing to replace it.
4d. If the lamp breaks and the projector is hung from
a ceiling or installed in a high place, unplug the
AC power cord from the AC power outlet and call
a McIntosh Authorized Dealer for assitance.
5e. It is recommended to replace the lamp when near
the end of its designed life. Do not use the lamp
beyond the maximum lighting time.
F. Do not look into the lens when the projector is
turned on. It could damage your eyesight.
LAMP HANDING PRECAUTIONS:
6f. Replace the defective lamp with a genuine Mc-
Intosh Lamp, matching the information in this
Owner’s Manual.
7g. Before replacing the lamp, carefully read the
Lamp Replacement Instructions in this Owner’s
Manual and the instructions supplied with the
replacement lamp.
8h. If the lamp breaks, leave the area immediately
and stay away for at least 30 minutes. Ventilate the
room, so as not to inhale the mercury vapor. If you
inhale the mercury vapor, see a physician immedi-
ately.
DANGER
This projector uses a high voltage glass mercury vapor
lamp. The lamp can break or fail to light when im-
properly handled, operating at abnormal temperatures
or after extended use.
Lamp life also varies, and operating the lamp be-
yond its intended service life may cause it to break or
fail to light properly, with risk of resulting damage to
the projector or surrounding property or persons. Do
not exceed the stated lamp life, nor attempt to override
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You
Table of Contents
Your decision to own this McIntosh MDLP1 Video Projec-
tor ranks you at the very top among discriminating video
viewers. You now have “The Best.” The McIntosh dedica-
tion to “Quality,” is assurance that you will receive many
years of viewing enjoyment from this unit.
Please take a short time to read the information in this
manual. We want you to be as familiar as possible with all
the features and functions of your new McIntosh.
Safety Instructions............................................................2
Thank You and Please Take a Moment.............................4
Technical Assistance and Customer Service....................4
Table of Contents ..............................................................4
General Information .........................................................5
Connector and Cable Information ....................................6
Introduction.......................................................................7
Performance Features .......................................................7
Dimensions .......................................................................8
Installation:
Please Take A Moment
Overview...........................................................................9
Ventilation......................................................................... 9
Projector and 16:9 Screen Mounting Location................10
Projector and 4:3 Screen Mounting Location................. 12
Initial Setup......................................................................14
Connections:
Rear Panel Connections.................................................. 16
How to Connect the MDLP1 .......................................... 17
Connection Diagrams (Separate Sheet)........ Mc2A,Mc2B
Remote Control:
The serial number, purchase date and McIntosh Dealer
name are important to you for possible insurance claim or
future service. The spaces below have been provided for
you to record that information:
Serial Number: __________________________________
Purchase Date: __________________________________
Dealer Name: ___________________________________
Remote Control Push-buttons......................................... 18
How to Operate by Remote Control ............................... 19
Operation:
Front Panel Push-buttons, Indicators and Control..........20
Default Settings ...............................................................21
How to Operate the MDLP1........................................... 22
Additional Information:
Technical Assistance
If at any time you have questions about your McIntosh
product, contact your McIntosh Dealer who is familiar
with your McIntosh equipment and any other brands that
may be part of your system. If you or your Dealer wish
additional help concerning a suspected problem, you can
receive technical assistance for all McIntosh products at:
Specifications..................................................................30
Packing Instruction.........................................................31
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-1545
Fax: 607-724-0549
Customer Service
If it is determined that your McIntosh product is in need of
repair, you can return it to your Dealer. You can also return
it to the McIntosh Laboratory Service Department. For
assistance on factory repair return procedure, contact the
McIntosh Service Department at:
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-3515
Fax: 607-723-1917
Copyright 2007 © by McIntosh Laboratory, Inc.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
General Information
CAUTION: To prevent possible damage to the Projec-
tor Lens Assembly, DO NOT at any time
attempt to LIFT, CARRY or RE-ORI-
select the desired Video Input and Picture Mode before
attempting to change the settings.
8. The MDLP1 has two Component Video Inputs for
analog video signals and two HDMI Inputs for Digital
video signals. The On-Screen Menu System has selec-
tions for Composite Video, S-Video and RGB Inputs.
Those inputs have no functionality when selected on the
MDLP1.
9. When the symbol illustrated here is located on the prod-
uct or on its packaging indicates that this product must
not be disposed of with your other house-
ENT the Projector using the Lens.
1. The Main AC Power going to the MDLP1 and any other
McIntosh Component(s) should not be applied until all
the system components are connected together. Failure
to do so could result in malfunctioning of some or all of
the system’s normal operations. When the MDLP1 and
other McIntosh Components are in their Standby Power
Off Mode, the Microprocessor’s Circuitry inside each
component is active and communication is occurring
between them.
hold waste. Instead, it is your responsibil-
ity to dispose of your waste equipment by
2. For additional connection information, refer to the
owner’s manual(s) for any component(s) connected to
the MDLP1 Video Projector.
handing it over to a designated collection
point for the recycling of waste electrical
and electronic equipment. The separate
3. To protect the Projector Lens from possible damage it is
advisable to keep the Lens Cover on the Projector dur-
ing the following:
collection and recycling of your waste
equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a
manner that protects human health and the environ-
ment. For more information about where you can drop
off your waste equipment for recycling, please contact
your local city office, your household waste disposal
service or the McIntosh Dealer where you purchased
the product.
a. Transporting of the projector.
b. Installation and connection of the projector.
c. During the installation of other items and/or
remodeling of the room where the projector is
located.
4. The Projector Lens is a precision optical device with
special coatings just like you would find on Profes-
sional Cameras. In the event the Lens requires cleaning
to remove airborne particles such as dust and dirt from
the Lens, use a safe cleaning product such as a clean
and dry 3MTM Scotch-Brite® Microfiber Lens Cleaning
Cloth. At no time should ordinary household cleaning
products be used to clean the Lens, as damage will oc-
cur.
5. A McIntosh Power Controller may be added to the
MDLP1 to provide AC Power Switching to components
without Power Control Connections, such as a motor-
ized projection screen. See your McIntosh Dealer for
additional information.
6. The IR Input, with 1/8 inch mini phone jack, is config-
ured for non-McIntosh IR sensors such as a Xantech
Model 291-80 or equivalent. To avoid possible interac-
tion, the MDLP1 Sensors may be disabled by activat-
ing the On-Screen Menu, then select from the menu
Config→Remote Control→Wired. Then deactivate the
On-Screen Menu. Refer to the “How to Operate the
MDLP1” starting on page 23.
7. The On-Screen Menu System for adjustment of settings
is interactive and Video Input type based, make sure to
3MTM is a trademark of the 3M Company and Scotch-Brite® is a registered trademark of the 3M Company.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector and Cable Information
Power Control Connectors
The MDLP1 Power Control Output Jacks send and Power
Control Input Jacks receive Power On/Off Signals when
connected to McIntosh and other non-
McIntosh Components. A 1/8 inch
stereo mini phone plug is used for con-
Power
Control
N/C
nection to the Power Control Input and
Outputs on the MDLP1.
Ground
Note: The Data and Power Control Connecting Cable is avail-
able from the McIntosh Parts Department:
Data and Power Control Cable Part No. 170-202
Six foot, shielded 2 conductor, with 1/8 inch stereo mini
phone plugs on each end.
Data Port Connectors
The MDLP1 Data In Port receives
Data
Signal
N/C
Remote Control Signals from other
Data
Ground
McIntosh Components. A 1/8 inch
stereo mini phone plug is used for
connection. The IR Ports also use a
1/8 inch stereo mini phone plug and
allow the connection of other brand
IR Data
Control
N/C
IR Receivers to the MDLP1.
Ground
RS232 DB9 Connector Pin Layout
1. N/C
6. N/C
7. N/C
8. N/C
9. N/C
2. Data Out (TXD)
3. Data In (RXD)
4. N/C
5. Gnd.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors and Cable Information, Introduction and Performance Features
Introduction
video source, from 480i to 1080p. There is a special 1080p
direct pixel pass through mode when the MDLP1 Projector
is used with the McIntosh VP1000 Video Processor.
The McIntosh MDLP1 Video Projector is one of the finest
projectors ever created. It utilizes the latest Digital Micro-
mirror DeviceTM containing over 2 million individual pixels
(1080p) and produces images of such high quality, it’s just
like being there.
• Video Adjustments
The MDPL1 allows for complete adjustment of all the im-
portant image quality effecting parameters, such as Color
Temperature, Gamma and Black Level. There are also user
adjustments with the ability to store the settings for future
recall, along with three preset modes (Theater, Standard
and Dynamic).
Performance Features
•DLP Chip
The McIntosh MDLP1 Video Projector incorporates the
latest and largest available Digital Light Processing (DLP)
Dark Chip for use in a Home Theater Projector. The large
chip size is 0.95 inch and produces a High Definition Im-
age of 1920 x 1080 pixels.
• HDMI Connectivity
The MDLP1 has two HDMI (High-Definition Multimedia
Interface) inputs and accepts 1080p signals.
• Advanced Optical System
The light source for the projector is the industry’s only 200
Watt DC Super High Pressure lamp assembly. This assures
an image with even illumination, focused from edge to
edge and accurate fully saturated colors. The light is fil-
tered by a large 98mm 7-segment color wheel incorporat-
ing a Neutral Density Filter Segment which enhances the
black level during dark scenes. After the light is reflected
by the DLP Chip, it is then precisely focused by a Konica-
Minolta custom designed zoom lens. This lens is fully
sealed and consists of 13 all-glass elements. The optics al-
low screen sizes ranging from 70 inches to 250 inches with
a 16:9 wide aspect ratio for the Medium Throw Lens or 80
inches to 300 inches with a 16:9 wide aspect ratio for the
Long Throw Lens.
• Total Component Integration
The MDLP1 is designed to work seamless with the McIn-
tosh VP1000 Video Processor and the McIntosh AP1000
Audio Processor.
• On-Screen Information Displays
The On-Screen Display indicates the Source Selection and
Information about the source signal. The Menu Selections
and Adjustments are also displayed on screen.
• Die Cast Internal Chassis
The MDLP1 die cast aluminum internal chassis assures
the precise mechanical alignment of the entire hermetically
sealed optical light path, which is necessary for a sharp,
highly detailed and accurate color image. The die cast
chassis also assures low operating noise and also helps to
dissipate heat away from the sensitive internal components.
• Advanced Filter Wheel Design
The color filter wheel spins at 10,800 RPM, making color
breakup (rainbow effect) a thing of the past. The quiet
filter wheel motor uses a Fluid Dynamic Bearing for silent
and reliable operation.
• Machined Top and Bottom Panels
The MDLP1 Top and Bottom Panels are machined from
thick aluminum with a smooth black anodized finish.
• Placement Compensation
The MDLP1 Projector incorporates numerous adjustments,
compensating for less then ideal projector/screen position-
ing. These adjustments include a Lens shift feature for
vertically positioning the projection point, digital correc-
tion of vertical keystone distortion and projection modes for
functional, hanging and rear projection.
• Special Power Supply
Fully regulated Power Supplies ensure stable noise free
operation even though the power line varies.
• Fiber Optic Solid State Front Panel Illumination
The even illumination of the Top Panel is accomplished by
the combination of a custom designed Fiber Optic Light
Diffuser and a extra long life Light Emitting Diode (LED).
The glass Top Panel ensures the pristine beauty of the
MDLP1 will be retained for many years.
• Enhanced Video Processing
The Video Circuitry uses the very latest in processing
algorithms to produce an excellent image regardless of the
Digital Micromirror Device, Digital Light Processing, DLP, DLP logo, and DLP
Medallion logo are registered trademarks of Texas Instruments.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Dimensions
The following dimensions can assist in determining the
best location for your MDLP1. There is additional informa-
tion on the next page pertaining to installing the MDLP1
into cabinets.
20-1/4"
51.44cm
6-1/4"
15.88cm
6-3/4"
17.15cm
Front View of the MDLP1
9-1/2"
24.13cm
Adjustable Height
Front Feet
20-1/4"
51.44cm
6-3/4"
17.15cm
Rear View of the MDLP1
13"
33.02cm
1-1/8"
17-11/16"
44.93cm
3.18cm
(See Note 1)
Side View of the MDLP1
Note 1: The Long Throw Lens
deminsion is 1- 3/8 (3.49cm)
3-1/4"
8.26cm
13-3/4"
34.93cm
14-1/8"
35.88cm
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Overview
For the best possible image reproduction by the McIntosh
MDLP1 Video Projector, it is important to observe the fol-
lowing:
CAUTION: The MDLP1 Video Projector weight
is 40 pounds (18.14 kilograms). When
mounting the projector to a building
structure it is important to follow all of
the local building/constuction codes.
1. Decide on a viewing area with either subdued and/
or controlled ambient lighting.
Primary
Warm Air
Exit
2. Choose a projector screen designed specifically to
work with images from a DLP Projector.
3. Locate the position of the MDLP1 Projector rela-
tive to the projector screen to maximize image
quality and minimize optical distortions.
4. Provide adequate ventilation.
MDLP1 Bottom View
The information below and on the following pages will as-
sist in the location of the Projector. It is recommended that
the Professionals at your McIntosh Dealer, who are skilled
in all aspects of installation and operation, install the
MDLP1 Video Projector and any associated audio/video
equipment.
Secondary Cool Air
Input No. 2
Secondary Cool Air
Input No. 3
Ventilation
Primary
Cool Air
Input No. 2
Always provide adequate ventilation for your MDLP1.
Cool operation ensures the longest possible operating life
for any electronic instrument. Do not install the MDLP1
directly above a heat generating component. Refer to fig-
ures 1 and 2.
Figure 1
Primary
The MDLP1 is designed to be placed upright on a solid
flat surface, resting on its three feet with unrestricted air
flow around it. Allow at least 1 foot (30.48 cm) of space
between the Primary Warm Air Exit ventilation holes and
the nearest wall or obstruction. There should be at least
3 inches (7.62 cm) between the Primary Cool Air Input
ventilation holes and the nearest wall or obstruction. The
ambient air temperature should not exceed 95°F (35°C).
The projector uses two primary and three secondary
cool air input vents together with one primary warm air
exit vent. Refer to the illustration on this page. The air flow
in or out of these vents needs to be unrestricted at all times
during operation.
Cool Air
Input No. 1
Secondary Cool Air
Input No. 1
MDLP1 Rear View
Figure 2
In the event the MDLP1 is to be placed into an enclo-
sure restricting air flow around the projector, some type of
ducted forced air venting system would need to be imple-
mented for the primary input 1 and 2 vents along with the
primary exit vent.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector and 16:9 Screen Mounting Location
The illustrations below together with the charts on the adjacent page, will help to assure the correct mounting locations
for both the projector and the screen.
Projector mounted from the ceiling
Ceiling
Top of Screen
Acceptable
Projector
Mounting
Height
Vertical
Screen
Height
Vertical Center of Screen
CAUTION:
The MDLP1 Video Projector
weight is 40 pounds (18.14 ki-
lograms). When mounting the
projector to a building struc-
ture it is important to follow
all of the local building/con-
stuction codes. Not evaluated
for Wall or Ceiling Mounting.
Bottom of Screen
Distance (Minimum-Maximum) between
the Screen and the Projector Lens
Projector placed above the floor
Distance (Minimum-Maximum) between
the Screen and the Projector Lens
Top of Screen
Vertical Center of Screen
Vertical
Screen
Height
Acceptable
Projector
Mounting
Height
Bottom of Screen
Floor
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, con’t
MDLP1M (with Medium Throw Lens) - 16:9 Screen Size (1.77:1 Aspect Ratio)
Screen Diagonal
Screen Width
Screen Height
Minimum Distance
Maximum Distance
Inches Centimeters
Inches
61
Centimeters
155.0
Inches
Centimeters
Inches
88-6/16
90-15/16
101-5/16
103-14/16
106-7/16
114-3/16
116-13/16
127-2/16
134-14/16
140-1/16
153
Centimeters
224.3
230.8
257.1
Inches
129-1/16
132-13/16
147-13/16
151-9/16
155-5/16
166-8/16
170-4/16
185-4/16
196-7/16
203-15/16
222-11/16
228-4/16
247
Centimeters
327.6
70
72
177.8
182.9
203.2
208.3
213.4
228.6
233.7
254.0
269.2
279.4
304.8
312.42
337.8
342.9
381.0
431.8
508.0
635.0
34-5/16
35-5/16
39-4/16
40-3/16
41-3/16
44-2/16
45-2/16
49
87.2
89.7
62-12/16
69-12/16
71-8/16
159.4
177.1
181.5
186.0
199.2
203.7
221.4
234.7
243.5
265.7
272.3
294.4
298.9
332.1
376.3
442.8
553.5
337.1
80
99.0
375.1
82
102.1
104.6
112.1
114.6
124.5
132.0
137.0
149.4
153.2
165.6
168.1
186.8
211.7
249.1
311.3
263.6
270.2
289.9
296.4
322.7
342.3
355.5
388.3
398.1
430.9
437.5
486.7
552.3
650.7
814.7
384.6
394.1
422.6
432.1
470.1
498.6
517.6
84
73-3/16
90
78-7/16
92
80-3/16
100
106
110
120
123
133
135
150
170
200
250
87-3/16
92-6/16
51-15-16
53-15/16
58-13/16
60-5/16
65-3/16
66-3/16
73-9/16
83-6/16
98-1/16
122-9/16
95-14/16
104-9/16
107-3/16
115-15/16
117-11/16
130-12/16
148-3/16
174-5/16
217-14/16
565.1
579.4
626.9
636.4
707.6
802.6
945.1
1,182.6
156-14/16
169-12/16
172-6/16
191-12/16
217-9/16
256-6/16
321
250-12/16
278-13/16
316-4/16
372-6/16
465-15/16
MDLP1L (with Long Throw Lens) - 16:9 Screen Size (1.77:1 Aspect Ratio)
Screen Diagonal
Screen Width
Screen Height
Minimum Distance
Maximum Distance
Inches Centimeters
Inches
Centimeters
Inches
Centimeters
Inches
147-3/16
150-15/16
154-10/16
165-14/16
169-10/16
184-10/16
195-13/16
203-5/16
222
Centimeters
373.5
383.0
Inches
222-3/16
227-13/16
233-7/16
250-5/16
255-15/16
278-6/16
295-4/16
306-8/16
334-9/16
343
Centimeters
564.0
80
82
203.2
208.3
213.4
228.6
233.7
254.0
269.2
279.4
304.8
312.42
337.8
342.9
381.0
431.8
508.0
635.0
762.0
69-12/16
71-8/16
177.1
181.5
186.0
199.2
203.7
221.4
234.7
243.5
265.7
272.3
294.4
298.9
332.1
376.3
442.8
553.5
664.1
39-4/16
40-3/16
41-3/16
44-2/16
45-2/16
49
99.6
102.1
104.6
112.1
114.6
124.5
132.0
137.0
149.4
153.2
165.6
168.1
186.8
211.7
249.1
311.3
373.6
578.2
84
73-3/16
392.5
421.0
592.5
90
78-7/16
635.3
92
80-3/16
430.5
468.5
497.0
649.5
100
106
110
120
123
133
135
150
170
200
250
300
87-3/16
706.6
92-6/16
51-15/16
53-15/16
58-13/16
60-5/16
65-3/16
66-3/16
73-9/16
83-6/16
98-1/16
122-9/16
147-1/16
749.3
95-14/16
104-9/16
107-3/16
115-15/16
117-11/16
130-12/16
148-3/16
174-5/16
217-14/16
261-8/16
516.0
777.9
563.5
577.8
849.2
227-10/16
246-6/16
250-2/16
278-3/16
315-10/16
371-12/16
465-5/16
558-14/16
870.6
625.3
634.8
706.0
801.0
371-1/16
376-11/16
418-14/16
475
941.9
956.1
1,063.1
1,205.7
1,419.6
1,776.1
2,132.6
943.5
1,181.0
1,418.5
559-5/16
699-12/16
840-4/16
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector and 4:3 Screen Mounting Location
The illustrations below together with the charts on the adjacent page, will help to assure the correct mounting locations
for both the projector and the screen.
Projector mounted from the ceiling
Ceiling
Top of Screen
Acceptable
Projector
Mounting
Height
Vertical
Screen
Height
Vertical Center of Screen
CAUTION:
The MDLP1 Video Projector
weight is 40 pounds (18.14 ki-
lograms). When mounting the
projector to a building struc-
ture it is important to follow
all of the local building/con-
stuction codes. Not evaluated
for Wall or Ceiling Mounting.
Bottom of Screen
Distance (Minimum-Maximum) between
the Screen and the Projector Lens
Projector placed above the floor
Distance (Minimum-Maximum) between
the Screen and the Projector Lens
Top of Screen
Vertical Center of Screen
Vertical
Screen
Height
Acceptable
Projector
Mounting
Height
Bottom of Screen
Floor
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, con’t
MDLP1M (with Medium Throw Lens) - 4:3 Screen Size (1.33:1 Aspect Ratio)
Screen Diagonal
Screen Width
Screen Height
Minimum Distance
Maximum Distance
Inches Centimeters
Inches
56
Centimeters
142.2
Inches
42
Centimeters
106.7
Inches
108-8/16
111-10/16
124-5/16
127-7/16
130-10/16
140-1/16
143-4/16
155-14/16
165-6/16
171-11/16
187-8/16
192-4/16
208
Centimeters
275.4
283.4
315.5
323.5
331.5
355.6
363.6
395.7
419.7
Inches
158-5/16
162-14/16
181-3/16
185-13/16
190-6/16
204-2/16
208-11/16
227
Centimeters
401.8
413.4
70
72
177.8
182.9
203.2
208.3
213.4
228.6
233.7
254.0
269.2
279.4
304.8
312.42
337.8
342.9
381.0
431.8
508.0
635.0
57-10/16
64
146.3
162.6
166.6
170.7
182.9
186.9
203.2
215.4
223.5
243.8
249.9
270.3
274.3
304.8
345.4
406.4
508.0
43-3/16
48
109.7
121.9
125.0
128.0
137.2
140.2
152.4
161.5
167.6
182.9
187.5
202.7
205.7
228.6
259.1
304.8
381.0
80
459.9
82
65-10/16
67-3/16
72
49-3-16
50-6/16
54
471.5
84
483.2
518.0
90
92
73-10/16
80
55-3/16
60
529.6
100
106
110
120
123
133
135
150
170
200
250
576.1
84-13/16
88
63-10/16
66
240-12/16
249-14/16
272-12/16
279-10/16
302-9/16
307-2/16
341-7/16
387-4/16
455-14/16
570-6/16
611.0
435.8
475.9
487.9
528.0
536.0
596.2
676.4
796.7
997.2
634.2
692.3
709.8
767.9
96
72
98-6-16
106-6/16
108
73-13/16
79-13-16
81
211-3/16
234-14/16
266-8/16
313-14/16
392-14/16
779.5
866.6
982.8
1,157.1
1,447.6
120
90
136
102
160
120
200
150
MDLP1L (with Long Throw Lens) - 4:3 Screen Size (1.33:1 Aspect Ratio)
Screen Diagonal
Screen Width
Screen Height
Minimum Distance
Maximum Distance
Inches Centimeters
Inches
48
Centimeters
121.9
Inches
36
Centimeters
91.4
Inches
203-13/16
157-11/16
162-4/16
180-9/16
185-3/16
189-12/16
203-8/16
208-1/16
226-6/16
240-2/16
249-4/16
272-2/16
279
Centimeters
517.4
Inches
203-13/16
238-4/16
245-2/16
272-10/16
279-8/16
286-6/16
307
Centimeters
517.4
60
70
152.4
177.8
182.9
203.2
208.3
213.4
228.6
233.7
254.0
269.2
279.4
304.8
312.42
337.8
342.9
381.0
431.8
508.0
635.0
762.0
56
57-10/16
64
142.2
146.3
162.6
166.6
170.7
182.9
186.9
203.2
215.4
223.5
243.8
249.9
270.3
274.3
304.8
345.4
406.4
508.0
609.6
42
43-3/16
48
106.7
109.7
121.9
125.0
128.0
137.2
140.2
152.4
161.5
167.6
182.9
187.5
202.7
205.7
228.6
259.1
304.8
381.0
457.2
400.2
411.8
604.7
72
622.1
80
458.3
469.9
692.0
82
65-10/16
67-3/16
72
49-3/16
50-6/16
54
709.4
84
481.6
726.9
90
516.4
779.3
92
73-10/16
80
55-3/16
60
528.0
574.5
313-15/16
341-7/16
362-1/16
375-13/16
410-3/16
420-9/16
454-15/16
461-13/16
513-6/16
582-3/16
685-6/16
857-6/16
1,029-6/16
796.7
100
106
110
120
123
133
135
150
170
200
250
300
866.6
84-13/16
88
63-10/16
66
609.4
632.6
690.7
918.9
953.9
96
72
1,041.2
1,067.4
1,154.7
1,172.1
1,303.1
1,477.7
1,739.6
2,176.1
2,612.6
98-6/16
106-6/16
108
73-13/16
79-13/16
81
708.2
766.3
777.9
301-14/16
306-8/16
340-13/16
386-10/16
455-4/16
569-12/16
684-3/16
120
90
865.0
981.2
136
102
160
120
1,155.5
1,446.0
1,736.5
200
150
240
180
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
The Initial Setup Section is to assist with minimizing
the possible geometric distortions in the projected image
caused by the physical orientation of the MDLP1 Video
Projector relative to the screen. While there are electronic
adjustments to correct for some of these geometric dis-
tortions, the best images will be achieved when minimal
electronic adjustments are used.
After the projector and
5. Rotate clockwise or
counterclockwise the
Knurled Ring surface
on the front section of
the projector lens to
perform an initial fo-
cus adjustment. Refer
to figures 5 and 6.
Note: Figure 6 is an
example of an
Figure 5
screen locations have been
established (refer to the four
previous pages), the next step
is to perform the basic optical
and mechanical orientation
out of focus im-
age. Do not be
concerned at this
time if the image
doesn’t fill the
screen, is not
adjustments as follows:
Note: Some installations
Figure 6
might require location
positional adjustments
in addition to and/or in
place of the projector’s
centered and/or has geometric distortion.
The next several adjustments will be performed to achieve
the following:
A. Fill the screen with the image.
B. Center the image both horizontally and verti-
cally on the screen.
C. Minimize any horizontal keystone distortion
of the image.
built-in adjustments.
1. Connect the projector to a
live AC Outlet.
2. Remove the protective
cover from the projector
D. Orient the image to be parallel with the top,
bottom and sides of the screen.
6. Rotate clockwise or counterclockwise the Knurled
Ring surface on
the rear section
of the projector
lens to fill the
screen with the
Crosshatch Test
Pattern. Refer to
lens.
3. The Red LED to the left
of the STANDBY/ON
Push-button lights to
Figure 3
indicate the MDLP1 is in Standby
mode. To Switch ON the MDLP1,
press the STANDBY/ON Push-button
on the Projector Control Panel or the
PROJector ON Push-button using the
Remote Control. The Green LED to
the right of the STANDBY/ON Push-
button lights to indicate the MDLP1
is ON. Refer to figures 3 and 4.
Note: It is normal for the projector
lamp warm up period to last
figures 5 and 7.
7. Move the entire
IMAGE SIZE
LARGER
projector slightly
to the left or
IMAGE FOCUS
right to center
the image hori-
zontally on the
about a minute before an image
appears on the screen.
SMALLER
Figure 7
4. Press the PATTERN Push-button on
the Control Panel or the Remote Con-
trol. Refer to figures 3 and 4.
The Crosshatch Test Pattern (Horizon-
tal and Vertical White Lines on a Black
Background) will appear on the screen
and will be used during the following
steps. Refer to figures 5 and 6.
screen.
8. Using the LENS
SHIFT Control, located on the Top Control Panel, cen-
ter the image vertically on the screen. Refer to figures
3, 8 and 9.
Note: If the Crosshatch Test Pattern lines change in color
from white to green, the current vertical height of
the projector relative to the screen will not produce
an acceptable image. Reposition either the projec-
tor or the screen vertically so when the image is
Figure 4
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
11. Using the Knurled Ring surfaces on the projector lens
adjust the size and focus of the image. Refer to figure 7.
12. Rotate the projector clockwise or counterclockwise
about the center horizontal axis to minimize any
horizontal keystone distortion. The top and bottom
horizontal lines of the Crosshatch Test Pattern should
be parallel with the top and bottom edges of the screen.
Refer to figures 5, 12 and 13.
Screen
Figure 8
13. Using the knurled
ring surfaces on
the projector lens
Screen
to adjust the size
and focus of the
image. Refer to
figure 7.
14. Repeat steps 6 thru
������
13 until no further
improvements can
be made.
Figure 9
Note: Correction
centered vertically on the screen the Crosshatch
Test Pattern lines are again white in color.
for any
vertical
keystone
9. Using the Knurled Ring surfaces on the projector lens
adjust the size and focus of the image. Refer to figure
7.
10. Rotate one or both of the projector feet to line up the
top and bottom horizontal lines of the Crosshatch Test
Pattern to be parallel with the top and bottom edges of
the screen. Refer to figures 5 and 10.
Figure 12
distortion
of the im-
age will be
performed
later during
the elec-
tronic setup
������
adjustments
on page 23.
15. Press the STAND-
BY/ON Push-
button on the
Projector Control
Panel or the PROJ
ON Push-button
using the Remote
Control.
Figure 13
Figure 10
Note: If more than several turns are needed there is a
release lever located next to the foot for rapid and
large changes in height. Refer to figure 11.
16. Temporarily place the previously removed protective
cover onto the projector lens.
17. Remove the AC Power Cord from the projector.
18. Proceed to the “How to connect the MDLP1”
on page 17.
Figure 11
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Connections and Switch
DATA IN Port receives
signals from McIntosh
A/V Control Center for
Remote Control Operation
TRIGGER 1 Output
sends a Turn-On signal
to other components
when the MDLP1 is
switched On
COMPONENT INPUTS receive Com-
ponent Video (Y, PR and PB) Signals
from Component Video Sources
POWER CONTROL IN
TRIGGER 2 Output
sends Turn-On
receives turn-on signals
from a McIntosh compo-
nent and POWER CON-
TROL OUT sends turn-on
signals on to another
signals to other com-
ponents and may be
assigned to activate
when a specific as-
pect ratio is selected.
McIntosh Component
RS232 connector for
connection to a com-
puter or other control
device
Connect the MDLP1
power cord to a live AC
outlet. Refer to informa-
tion on the back panel
to determine the correct
voltage
Switches Off
the illumina-
tion to the Top
Control Panel
McIntosh Logo
IR INput for
connecting an
IR Receiver
HDMI Inputs receive
digital video signals
from a McIntosh A/V
Control Center and/or
other source compo-
nents
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect the MDLP1
How to Connect the MDLP1
The MDLP1 has the ability to automatically switch power
On/Off to McIntosh Components via the Power Control
If the MDLP1 is connected to a McIntosh Audio/Video
Control Center MX136, MX135, MX120, MX119, or
and Trigger Connections. The Data Port Connections allow MX134 (MX Series) add the following connection:
for the remote operation of the MDLP1 from other McIn-
tosh Components. With an external sensor connected to
the MDLP1, remote control operation is possible when the
MDLP1 is located in an enclosure.
The connection instructions below, together with the
AP1000/MDLP1/VP1000 Input and Control Connection
Diagrams located on the separate folded sheet “Mc2A and
Mc2B”, are an example of a typical audio/video system.
Your system may vary from this; however, the actual com-
ponents would be connected in a similar manner.
For additional information refer to “Connector and
Cable Information” on page 6.
6. Connect a Video Cable from the MDLP1 Y1, PB1 and
PR1 COMPONENT VIDEO Input Jacks to the McIn-
tosh MX Series Component Video MON A Jacks.
7. Connect a Video Cable from the MDLP1 HDMI 1
Input Jack to the McIntosh MX Series HDMI MON A
Output Jack.
Note: Only the MX136 and MX120 Audio/Video Con-
trol Centers will have a HDMI MON A Jack.
AC Power Cord Connections:
8. Connect the MDLP1 AC Power Cord to a live AC
outlet.
9. Connect the remaining components’ AC Power Cords.
Note: With the addition of a McIntosh Power Controller
connected to the MDLP1, AC Power Switching can
be provided to components such as a motorized
projection screen. Contact your McIntosh Dealer for
additional information.
Power Control Connections:
1. Connect a Control Cable from the MDLP1 POWER
CONTROL IN Jack to the Power Control Out A Jack
on the McIntosh VP1000 Video Processor.
If the MDLP1 is connected to a McIntosh Audio/Video
Control Center MX136, MX135, MX120, MX119, MX134
or MX132 (MX Series) add the following connection:
2. Connect a Control Cable from the MDLP1 POWER
CONTROL IN A Jack to the McIntosh MX Series
Power Control Zone A Out Jack.
Data Control Connections:
When the MDLP1 is connected to the McIntosh VP1000
Video Processor no Data Port connection is necessary.
If the MDLP1 is connected to a McIntosh Audio/Video
Control Center MX136, MX135, MX120, MX119, MX134
or MX132 (MX Series) add the following connection:
3. Connect a Control Cable from the MDLP1 DATA IN
Jack to the McIntosh MX Series SUM A Data Port
Jack.
Video Connections:
When the MDLP1 is connected to the McIntosh VP1000
Video Processor add the following connections. If there is
no VP1000 proceed to step 6.
4. Connect a Video Cable from the MDLP1 Y1, PB1 and
PR1 COMPONENT VIDEO Input Jacks to the McIn-
tosh VP1000 Component Video MON A Jacks.
5. Connect a Video Cable from the MDLP1 HDMI 1
Input Jack to the McIntosh VP1000 HDMI MON A
Output Jack.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Push-Buttons
LED illuminates during the time
a remote command is sent to the
MDLP1
Selects which component, either the
VP1000 Processor or the MDLP1
Projector, the remote control com-
mands are sent to
Used to change the Color
Temperature settings
Press to adjust the
selected function
Used to change the Lens Iris
opening size
Used to change the
Gamma settings
Press to activate the various On-
Screen Menus, press a second time
to deactivate the Menus
Press to recall various
On-Screen Information,
press a second time to
deactivate the Menus
Used to navigate up, down, to
the left and to the right through
the various menus. Also used
to select the desired function or
option
Press to change the Aspect
Ratio of the video image
Press to select one of three
predefined picture settings
or select one of nine user
defined picture settings
Press to select the desired Screen
Blanking Setting from Memory
Locations 1-3 or switch Off the
Blanking Function
Changes the film frame pro-
cessing from Auto to Off
Press to Power ON or
OFF the MDLP1
Activates the OnScreen
Crosshatch Test Pattern
Press to select the desired video
source, Component 1, Compo-
nent 2, HDMI 1 or HDMI 2
Note: Push-buttons whose function is not identified above
are for use with other McIntosh Components
18
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Remote Control
How to use the Remote Control
The supplied Remote Control is capable of directly control-
ling the functions of the McIntosh MDLP1 Video Projector
and VP1000 Video Processor. For additional information
on the various video adjustments and their purpose, please
refer to the “How to Operate the MDLP1” section of this
manual starting on page 22.
Color Temperature
Allows for changing on the fly1 the color neutrality of the
image from warm thru cool (six different settings).
Iris
Allows for changing on the fly1 the overall Image Bright-
ness by varying the opening size of the Lens Iris (two
different settings).
Note: At times it might appear the selected function is not re-
sponding when using the Remote Control. This can be
due to the Input selected, the presence of a video signal
for that input and the Picture Mode selected. Please
refer to page 22 for additional information.
Gamma
Allows for changing on the fly1 selected narrow segments
of the gray scale, where the selected segment range of
brightness/contrast is expanded (eight different segments).
Note: The term “Gray Scale” refers to the image intensity
range from Black to White with shades of gray in-be-
tween.
Device Selection
This Remote Control is used to operate the McIntosh
MDLP1 Video Projector and the VP1000 Video Processor.
When using the Remote Control with the MDLP1, first
press the DEVICE PROJector push-button and then press
the push-button for the desired function. It is only required
to press the DEVICE PROJector push-button once, un-
less the Remote Control is also being used to control the
VP1000 Video Processor.
When the Remote Control is being used to control both
McIntosh Components, either the DEVICE PROCessor
or the DEVICE PROJector push-button would need to
be pressed first, before sending
Aspect Ratio
Allows for presenting the image with different height to
width sizes. The choices available vary according to the
original source material type, projector settings and input
used.
Picture Modes
There are three preset modes THTR (Theater), STD (Stan-
dard) and DYN (Dynamic) along with three user group
set selections, G1, G2 or G3. With every press of the G1
push-button a different User Setting will be selected (U1,
U2 or U3). The G2 push-button will select (U4, U5 or U6)
and the G3 push-button selects (U7, U8 or U9). Refer to
“How to Operate the MDLP1” for additional information
on using the User defined image settings.
Note: Changing the Picture Mode using the Remote Control
Picture Mode Push-buttons will not occur if the On-
Screen Menu is active. If the Menu is active, the Picture
Mode may be changed using the Picture Mode Menu
functions.
commands to the desired compo-
nent.
Note: When any of the Push-but-
tons in the adjacent illustra-
tion are pressed, the Remote Control automatically
switches to sending VP1000 Video Processor IR Codes.
Power On
Press PROJector ON to switch the power On to the
MDLP1.
Power Off
Press PROJector OFF to switch the power Off to the
MDLP1.
Adjust Functions
After menu functions displaying a horizontal adjust-
ment bar on the screen have been selected, such as Image
Brightness, the ADJUST+ or ADJUST- push-buttons may
be used to vary the brightness of the image.
1When some Picture Modes are selected, “the changing on the
fly” feature is not available.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Push-buttons, Indicators and Control
Allows the Projec-
tor Lens assembly to
be raised or lowered
vertically for center-
ing the image on the
screen
Used to navigate up,
down, to the left and
to the right through
the various menus.
Also used to select the
desired function or
option
Indicates when
the projector
lamp has failed
or if one of the
safety functions
has been acivated
Activates the On-
Screen Cross-
Hatch Video Test
Pattern
IR Sensor
receives
commands
from a
Remote
Control
Activates the
On-Screen
Menus for
changing the
settings
Selects one
of four Video
Sources available
and indicates the
selected video
input
Power ON
Indicator
Standby Power
On Indicator
STANDBY/ON
Push-button
switches the
MDLP1 ON or
OFF (Standby)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Default Settings
Default Settings
The Default Settings Charts indicate the On-Screen Menu
Name, Function, Default Settings and the page number for
additional information.
MENU
FUNCTION
SETTING PAGE
MENU
FUNCTION
SETTING PAGE
Picture Mode Theater
Standard (Default)
Default
24
24
24
24
24
24
24
24
24
24
25
25
25
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
27
27
27
27
27
27
RGB/HD Adjust Mode
Readjust
Auto
27
27
27
27
27
27
27
27
27
23
27
27
27
27
27
23
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
23
29
29
Default
----
Dynamic
Default
Resolution H
Resolution V
Position H
Position V
Phase
0
User
Picture Adjust Gamma
Contrast
1
0
Standard
0
0
0
Brightness
Color
0
0
0
Clamp Position
Clamp Width
Keystone
0
Tint
0
0
Color Temp.
Lamp Mode
Iris
3
Display
0
0
Normal
F6.0
Full
0
Scale
Width
0
Aspect
Position H
Position V
Overscan
Installation
0
Fine Menu 1
Fine Menu 2
Input Signal
Sharpness
Noise Reduction
R Gain
0
0
Enable
Front
Top-L
English
Enable
Disable
Off
0
G Gain
0
OSD/Blanking Menu Position
Language
B Gain
0
R Bias
0
Status Info
G Bias
0
Power-Off Confirm
B Bias
0
Blanking Memory
Blanking Top
Cinema
Auto
Off
Expand
Auto
Off
0
0
VCR Mode
Black Level
FRC
Blanking Bottom
Blanking Left
0
0
Blanking Right
Auto Power Off
Trigger 2 Full
0
CEC
Config.
Disable
On
Picture Shift V
Luminance Gain
Chroma Delay
Component 1
Component 2
HDMI 1
0
Trigger 2 Normal
Trigger 2 Zoom
Trigger 2 V-stretch
Trigger 2 Through
Remote Control
Reset Lamp Life
Reset All
On
0
On
Auto
Auto
Auto
Auto
Auto
Auto
On
On
Wireless
No
HDMI 2
CSC-HDMI 1
CSC-HDMI 2
No
21
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate the MDLP1
Power
Source Selection
The Red LED to the left of the STANDBY/ON Push-but-
ton lights to indicate the MDLP1 is in Standby mode. To
Switch ON the MDLP1, press the STANDBY/ON Push-
button on the Projector Control Panel or the Projector ON
Push-button using the Remote Control. The Green LED to
the right of the STANDBY/ON Push-button lights to indi-
cate the MDLP1 is ON. Refer to figures 14 and 15.
Notes: 1. It is normal for the projector lamp warm up period
to last about a minute before an image appears on
the screen.
The default Source Select for the MDLP1 Projector is the
COMPonent 1 Input. There is an additional Component
Video Input (COMP 2) along with two HDMI Inputs.
Select the desired source using the push-buttons located on
the Projector Control Panel or on the PROJ INPUT Push-
buttons located on the Remote Control. Refer to figures 14
and 15.
Note: Whenever possible use HDMI connections between
the source device output to the MDLP1 Input. This
will yield better image quality, as the video signal
will go through one less analog to digital conver-
sion process and possibly one less digital to analog
conversion process as well.
2. If the Initial Setup for the MDLP1 has not yet been
performed refer to page 14 at this time.
Image Adjustments and Setting changes
All of the electronic based image adjustments and pro-
cessing settings are performed by using the extensive
On-Screen Menuing System. The
On-Screen Menuing System is in-
teractive and the ability to change
a given setting is dependent on
the Input selected, the presence
of a video signal for that input,
the Picture Mode selected and are
automatically saved for the cur-
rently selected video input. When
a menu item is “grayed out” it
can not be changed until either
another Input is selected, a signal
is present or a different Picture
mode is selected.
The selection of a menu item
and the available choices/adjust-
ments are performed by using the
Navigation (◄LEFT, ►RIGHT,
▲UP or ▼DOWN) Push-buttons
along with the ENTER/SELECT
Push-buttons located on the Pro-
jector Control Panel and/or using
the Remote Control Push-buttons.
The following examples
will illustrate how to use the
On-Screen Menuing System by
performing the Display Installa-
tion Orientation, Display Vertical
Keystone Adjustment and Remote
Control Configuration. All of the
remaining menu options are per-
Figure 14
formed in a similar manner.
Figure 15
22
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate the MDLP1
Display Installation Orientation:
4. Press the Navigation ►RIGHT push-button and the
On-Screen Display changes to show the video image
selected plus a horizontal adjustment bar located near
the bottom of the screen. Refer to figure 18.
1. Press the MENU Push-button on either the Projec-
tor Control Panel or on the Remote Control. Refer to
figures 14 and 15.
2. Using the Navigation ▲UP or ▼DOWN Push-button,
select DISPLAY from the Main Menu choices. Refer to
figure 16.
Keystone
0
Figure 18
5. Press the ◄LEFT or ►RIGHT Navigation push-button
to adjust the image so the left and right vertical sides of
the image are parallel to the sides of the screen. Refer
to figures 19 and 20.
Standard 1
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Keystone
Scale
0
0
0
0
0
Width
Position H
Position V
Overscan
Installation
Note: The ADJUST + and - Push-buttons on the Remote
Control may also used.
OSD/Blanking
Config.
Front
Rear
Enable
Front
F+Ceiling
R+Ceiling
Figure 16
3. Using the Navigation ►RIGHT push-button plus the
▲UP or ▼DOWN Push-button, select INSTALLA-
TION from the Display Menu choices.
4. Press the Navigation ►RIGHT push-button plus the
▲UP or ▼DOWN Push-button select the correct
orientation of the projector relative to the screen. Refer
to figure 17.
Figure 19
Standard 1
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Keystone
Scale
0
0
0
0
0
Width
Position H
Position V
Overscan
Installation
OSD/Blanking
Config.
Enable
Front
Figure 17
Figure 20
In order to see the sides of the projected image it might be
necessary to temporarily reduce the size of the image by
using the Lens Mechanical Size Adjustment, refer to page
14. After the Vertical Keystone correction has been per-
formed, the projected image might not fill up the screen.
If necessary, use the Lens Mechanical Size Adjustment to
correct.
Vertical Keystone Adjustment:
1. Press the MENU Push-button on either the Projec-
tor Control Panel or on the Remote Control. Refer to
figures 14 and 15.
2. Using the Navigation ▲UP or ▼DOWN Push-button,
select DISPLAY from the Main Menu choices. Refer to
figure 17.
3. Using the Navigation ►RIGHT push-button plus the
▲UP or ▼DOWN Push-button, select KEYSTONE
from the Display Menu choices.
Remote Control Configuration:
The MDLP1 has two built-in sensors, one on the front of
the projector and the other sensor located on the Control
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel. In certain installations it might be desirable to use
an external sensor connected to the IR Jack. If an external
sensor is used, it is advisable to switch Off the built-in sen-
sors to prevent possible interference. To switch Off these
sensors perform the following steps:
1. Press the MENU Push-button on either the Projec-
tor Control Panel or on the Remote Control. Refer to
figures 14 and 15.
Standard 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Theater
Standard
Dynamic
User
Default
1
Default
Default
1
1
2
3
OSD/Blanking
Config.
2. Using the Navigation ▲UP or ▼DOWN Push-button,
select CONFIG. from the Main Menu choices. Refer to
figure 21.
Figure 23
Standard 1
Remote Control. To have the MDLP1 memorize the current
setting perform the following:
1. Select a memory location (U1 thru U9) and then press
the SELECT/ENTER Push-button.
2. Make the changes to the image using the menu sys-
tem.
3. Reselect the memory location from step one and then
press the SELECT/ENTER Push-button.
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Auto Power Off
Trigger 2 Full
Enable
On
Trigger 2 Normal
Trigger 2 Zoom
On
On
Trigger 2 V-stretch On
Trigger 2 Through
Remote Control
Reset Lamp Life
Reset All
On
OSD/Blanking
Config.
Figure 21
Picture Adjust Menu
There are various image adjustments available as follows:
Refer to figure 24.
3. Using the Navigation ►RIGHT push-button plus the
▲UP or ▼DOWN Push-button, select REMOTE
CONTROL from the Config. Menu choices.
4. Press the Navigation ►RIGHT push-button and the
On-Screen Display changes to show a window. Refer
to figure 22.
User 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Gamma
Contrast
Brightness
Color
A
A
B
C
0
0
0
0
D
E
5. Press the ◄LEFT or
►RIGHT Navigation
push-button to select
Wireless ?
Tint
Color Temp.
Lamp Mode
Iris
3
���
��
Theater
Standard
Dynamic
OSD/Blanking
Config.
Normal
F6.0
Full
YES to disable the
Figure 22
enternal sensors or NO
to activate the internal sensors.
Aspect
Figure 24
6. In order to activate the sensor choice, it is necessary to
press the ENTER Push-button on the Control Panel.
Note: The SELECT Push-button on the Remote Control
will not activate the choice.
Gamma - There are eight different settings changing a
narrow range of the gray scale.
Color Temp. - The Color Temperature effects to what de-
gree of neutrality the gray scale is.
Picture Mode Selection
The MDLP1 has three predefined Picture Modes; Theater,
Standard, Dynamic. There are also nine User definable
Picture Modes. Refer to figure 23. A Picture Mode is a
Memory Location that remembers the current image set-
tings which are adjustable for the currently selected input.
There are two ways to select the Picture mode: select-
ing a mode from the On-Screen MENU or pressing the
Picture Mode push-buttons (THTR, STD, DYN) on the
Setting - Color Temperature (° Kelvin)
1
2
3
4
5
5250° K (overall reddish tint)
5800° K (slightly overall reddish tint)
6500° K (most neutral, default setting)
7500° K (slightly overall bluish tint
9300° K (overall bluish tint)
HB
High Bright (Display brightest image)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate the MDLP1, con’t
Lamp Mode - The Normal setting provides a brightly il-
luminated image with reasonable projector
lamp life. The Economy setting has slightly
reduced illumination with an increase in
lamp life.
Iris - The Lens “F-Stop” setting effects the overall image
brightness and contast. The F6.0 setting will in-
crease the contrast range of the image. The F3.0 set-
ting will increase the brightness range of the image.
Aspect - Allows for changing the projected image size
height to width ratio to compensate for the differ-
ent image sizes from various sources materials
such as film and TV video. Refer to figure 25 and
the chart below.
User 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Gamma
Contrast
Brightness
Color
A
0
0
0
0
Tint
Full
Color Temp.
Lamp Mode
Iris
3
Normal
OSD/Blanking
Config.
Normal
F6.0
Full
Zoom
V-Stretch
Through
Aspect
Figure 25
ASPECT RATIO OPTIONS
16:9 VIDEO SOURCE
4:3 VIDEO SOURCE
MODE
INPUT
IMAGE
DECRIPTION
IMAGE
DECRIPTION
The Image Source Aspect
Ratio is 1.78:1
The Image Source Aspect
Ratio is 1.33:1
SIGNAL
(HDMI, 1080p signal)
The 16:9 image is displayed
with the correct aspect
The 4:3 image is enlarged
horizontally
FULL
NORMAL
ZOOM
The picture in normal ratio
16:9 is displayed
The picture in normal ratio
4:3 is displayed
Both the ver tical and
horizontal components are
enlarged
Both the ver tical and
horizontal components are
enlarged
The vertical component of the
aspect ratio is enlongated
The vertical component of the
aspect ratio is enlongated
V-STRETCH
THROUGH
Images are actual pixel size
Images are actual pixel size
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine Menu 1 Adjust
VCR Mode - On: A projector is forced into the intra-field
only deinterlacing mode.
In the Fine Menu 1 there are two user type adjustments,
image sharpness and noise reduction. The remaining
adjustments are best performed by a professional with the
necessary video signal generators and optical measurement
equipment. Refer to figure 26.
Off: A projector is used with external field
memories and operates in the full set of
deinterlacing modes, i.e., motion adaptive
video deinterlacing and full frame film
source deinterlacing using 3:2 pulldown
detection (2:2 pulldown for 625/50
Standard 1
0
0
0
0
0
0
0
�
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Sharpness
Noise Reduction
R Gain
sources).
Black level - Select the black level by a video source.
FRC - Auto: Frame Rate Conversion function is basically
off. However FRC turns on automatically de-
pending on vertical frequency of input signal.
On: Frame Rate Conversion function is On (60Hz
fixed).
G Gain
B Gain
R Bias
OSD/Blanking
Config.
G Bias
B Bias
CEC - On: Chroma Error Correction reduces CUE (Chro-
ma Up-sampling Error) of 1080i signals.
Off : Normally, use this mode.
Figure 26
Sharpness - Effects how soft or sharp the image is.
Noise Reduction - Reduces the amount of electronic noise
present in the video signal.
Picture Shift V - When Aspect on the Picture Adjust menu
is set to Zoom, this setting allows the
user to move the projected image verti-
cally in order to see parts on the image
not appearing on the screen.
Luminance Gain - This menu allows the users to set the
luminance gain.
Chroma Delay - This menu allows the users to set the chro-
minance delay.
R Gain - This menu allows setting the gain for red.
G Gain - This menu allows setting the gain for green.
B Gain - This menu allows setting the gain for blue.
R Bias - This menu allows setting the bias for red.
G Bias - This menu allows setting the bias for green.
B Bias - This menu allows setting the bias for blue.
Note : The settings made in Fine Menu 1 are saved in the cur-
rently selected Picture Mode (Default excluded).
Input Signal Resolution Selection
There are several SD (Standard Definition) and HD (High
Definition) types of video signals the MDLP1 is capable of
displaying. The default setting for the Component Video
and HDMI Inputs of the MDLP1 is AUTO. In the AUTO
Mode, the MDLP1 will automatically switch to the highest
resolution possible for each of the video signals it receives.
Refer to figure 28.
Fine Menu 2 Adjust
The following adjustment are intended to be use by a pro-
fessional installer to compensate for differences in video
signals from various sources. Refer to figure 27.
Standard 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Cinema
Auto
On
Note: The S-Video,Video and RGB Inputs are not used on the
VCR Mode
Black Level
FRC
MDLP1.
0 IRE
Auto
Off
Standard 1
CEC
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Component 1
Component 2
S-Video
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Picture Shift V
Luminance Gain
Chroma Delay
0
0
0
OSD/Blanking
Config.
Video
RGB
HDMI1
Figure 27
OSD/Blanking
Config.
HDMI2
CSC HDMI1
CSC HDMI2
Cinema - Auto: Automatically selects the cinema mode
when a video signal is input. NTSC: 3-2
pull down, PAL: 2-2 pull down.
Figure 28
Off: Pull-down processing is not performed.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate the MDLP1, con’t
Display Menu Adjust
Item
Resolution Selection
The Display Menu allows for electronic adjustments to be
made to the image to compensate for orientation of the pro-
jector relative to the screen. Refer to figure 30.
Note: Before using the electronic adjustments, make sure all
of the Initial Setup Mechanical Adjustments have been
made first. Refer to pages 14 and 15.
Component
1 and 2
HDMI
1 and 2
CSC HDMI
Auto, 480i/576i, 480p, 540p, 576p, 720p
1035i, 1080i, 1080p
Auto, 480i/576i, 480p, 576p, 720p, 1035i,
1080i, 1080p
Auto, RGB, YPBPR 4:4:4, YPBPR 4:2:2,
YCBCR 4:4:4, YCBCR 4:2:2,
1 and 2
Notes: CSC (Color Space Conversion) selection is for HDMI
inputs only. YPBPR mode is suitable for HD TV sig-
nals such a 720p, 1080i. YCBCR mode is suitable for
SD TV signals such a 480i, 480p.
Standard 1
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Keystone
Scale
0
0
0
0
0
Width
Position H
Position V
Overscan
Installation
RGB/HD Adjust
The RGB/HD allow for fine adjustments to be made to HD
(High Resolution) Video Signals. Refer to figure 29.
OSD/Blanking
Config.
Enable
Front
Standard 1
�
�
�
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Mode
Memory 1
Figure 30
Readjust
0
0
0
0
0
0
0
Resolution H
Resolution V
Position H
Position V
Phase
Keystone - Refer to “Vertical Keystone Adjustment” on
page 23.
Scale - Reduces the image size without changing the aspect
ratio. The image can be reduced to about 70% of
the original size.
OSD/Blanking
Config.
Clamp Position
Clamp Width
Width - Reduces the image width without changing the
image height. The width can be reduced to about
75% of the original size.
Position H, V - Adjust the position of the input signal. H
adjusts the horizontal position of the input
signal. V adjusts the vertical position of the
input signal.
Overscan - Selects whether to show or hide picture borders
with SD (Standard Definition) video signals.
Enable: Default mode.
Disable: Reduces the size of the image so the
edges of the video signal can be seen.
Installation - Refer to “Display Installation Orientation” on
page 23.
Figure 29
Mode - Auto: Automatically adjusts each of the RGB/HD
Menu items.
Memory: Allows for manual adjustments of the
(1-3) RGB/HD Menu items and the adjust-
ments can be stored in one of three
memory locations.
Resolution H, V - Adjusts the horizontal and vertical reso-
lution of the RGB/HD input signals.
Position H, V - Adjust the position of the input signal. H
adjusts the horizontal position of the input
signal. V adjusts the vertical position of the
input signal. The remaining adjustments
are for RGB signals and are thus “grayed
out”.
OSD/Blanking
The OSD (On-Screen Display) and Blanking Adjustments
default settings may be changed for personal preferences.
Refer to figure 31 on the next page.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Off: Switches Off the blank-
ing mode Off. No mask-
ing occurs.
Standard 1
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Menu Position
Language
Top-L
English
Enable
Status Info.
Config. Settings
Power-OFF Confirm. Enable
The items in the configuration menu determine how the
MDLP1 Projector interfaces with other equipment, such
as motorized projection screens. There are also settings
dealing with the MDLP1 Projection Lamp. Refer to figure
32 and your McIntosh Dealer for additional information
and/or assistance.
Blanking Memory
Blanking Top
Memory 1
0
0
0
0
OSD/Blanking
Config.
Blanking Bottom
Blanking Left
Blanking Right
Figure 31
Standard 1
Menu Position - There are nine different positions On-
Screen to display the menus.
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
Auto Power Off
Trigger 2 Full
Enable
On
Status Info. - Displays On-Screen information about the
status of the video input signal and when
other operational modes are selected. This
occurs when the INFO push-button or other
push-buttons are pressed on the Remote
Control.
Trigger 2 Normal
Trigger 2 Zoom
On
On
Trigger 2 V-stretch On
Trigger 2 Through
Remote Control
Reset Lamp Life
Reset All
On
OSD/Blanking
Config.
Enable: Displays the current status for a set
amount of time in the upper right-
hand corner of the screen.
Figure 32
Disable: The information is not displayed.
Power-OFF Confirm - Displays an On-Screen message
requesting confirmation after press-
ing either the PROJ OFF Push-but-
ton on the Remote Control or the
STANDBY/ON push-button on
the Projector Control Panel (as the
push-button may have been pressed
by mistake).
Auto Power Off - This feature allows for the MDLP1 to be
switched Off automatically 10 minutes
after there is a loss of a video signal on
the currently selected input, thus con-
serving the projectors lamp life.
Enable: This setting will activate the
feature. Approximately nine
minutes after there is a loss
of the video signal, an
Disable: Switches Off power to
the projector without the
option provided by the
confirmation message.
Enable: The confirmation message
will appear after press-
On-Screen message will
appear. If the MDLP1
doesn’t receive a video
Auto Power Off
It will be standby mode soon.
signal on the currently
selected input or a new
command is not issued via
Figure 33
ing either push-button to
switch power Off to the
projector.
the Control Panel or Remote
Control, the MDLP1 will
switch Off about one minute
later. Refer to figure 33.
Blanking Memory - There are three memory locations
capable of storing how much projected
image (top/bottom/sides) will be cut
off by black bands (masking) to pre-
vent viewing the undesirable parts of
the image.
Disable: The Auto Power Off Feature is
switched Off.
Tigger 2 - Is activated by changing the Aspect Ratio (Full,
Normal, Zoom, V-stretch and Through). This
allows for changing the size of the reflective
area of the projection screen (via motorized
masking) and/or the addition of an external lens
in the light path. With a given Trigger 2 (Full,
Memory 1-3: Each of the three mem-
ory locations will store
and retrieve the desired
masking settings.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate the MDLP1, con’t
Normal, Zoom, V-stretch and Through) set to
ON a 12VDC output will appear at the Trigger
2 Output Jack; when set to OFF, 0V appears at
Trigger 2 Output Jack.
mately 5 hours remaining.
Refer to figure 36. Finally,
Warning
the last warning message
will appear On-Screen,
the MDLP1 Projector will
shut Off and the Control
Panel WARNING/LAMP
LED will illuminate red.
Refer to figure 37.
Lamp Life 5 Hours
Remote Control - Selection includes the two built in sen-
sors along with any external sensor(s)
connected via the external IR Input Jack
or just external sensor(s). Refer to page
5, General Information Note 6.
Figure 36
Warning
Lamp Life 0 Hours
Figure 37
Wireless: Selects external sensor(s)
only.
Wired: Selects the two internal sensors
and any external sensor(s) connected to
the MDLP1.
Note: When making a change to the cur-
rent menu setting, the ENTER Push-
button on the MDLP1 Control Panel
must be used to effect the desired
After your McIntosh
Dealer has replaced the
Projector Lamp, check to
make sure the Lamp Life
has been reset by pressing
the INFO Push-button on
the Remote Control. The
On-Screen Display should
indicate 2,000 hours. If it
was not reset please do it
Reset Lamp Life ?
Yes
No
Figure 38
change.
Reset Lamp Life - The projection lamp used in the MDLP1
has a maximun life expectancy of 2,000
hours.
at this time by selecting the Reset Lamp
Life from the On-Screen Menu and then
select YES and press the ENTER Push-
button. Refer to figure 38.
If at any time you would like to know
how many hours of use are left for the
lamp, press the INFO Push-button on
the Remote Control and the On-Screen
Display will appear indicating the
number of hours remaining. Refer to
figure 34. When there is aproximately
Reset All - If it becomes necessary to reset all the menu
settings back to factory defaults (except for
the Lamp Life Setting),
select the Reset All from
the On-Screen Menu and
then select YES and press
the ENTER Push-button.
Refer to figure 39.
Reset All ?
Yes
No
Figure 39
Information
Video Input
Picture Mode
Gamma
HDMI 1 - 1080p
User 1
Reset of Microprocessors
A
In the unlikely event the controls of the MDLP1 stop func-
tioning, the microprocessors can be reset by disconnecting
the AC Power Cord from the MDLP1, waiting for 5 min-
utes and then reconnecting the AC Power Cord.
Aspect
Normal
Lamp Mode
Iris
Economy
F6.0
Lamp Life
Total Time
921 Hours
3653 Hours
Figure 34
100 hours of lamp life remaining, an
On-Screen Warning Message will ap-
pear briefly. Refer to figure 35. If you
have chosen not to replace
the lamp at this time, a
Warning
second warning message
will appear with approxi-
Lamp Life 100 Hours
Figure 35
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Optical Specifications
Power Requirements
Digital Micromirror Device
0.95 inch (16:9)
1920 x 1080 pixels
100 Volts, 50/60Hz at 350 watts
110 Volts, 50/60Hz at 350 watts
120 Volts, 50/60Hz at 350 watts
220 Volts, 50/60Hz at 350 watts
230 Volts, 50/60Hz at 350 watts
240 Volts, 50/60Hz at 350 watts
Lamp
Super High Pressure 200W DC
Lens
Note: Refer to the rear panel of the MDLP1 for the correct
voltage.
f: 30.7 – 44.5mm (medium throw lens)
f: 44.5 – 66.75mm (long throw lens)
F: F3.0/F6.0
Projected Image Size
General Specifications
70 to 250 inches (medium throw lens, 1.77:1 aspect ratio)
80 to 300 inches (long throw lens, 1.77:1 aspect ratio)
70 to 250 inches (medium throw lens, 1.33:1 aspect ratio)
60 to 300 inches (long throw lens, 1.33:1 aspect ratio)
Operating Temperature
41 to 95oF
5 to 35oC
Light Output
Operating Humidity
600/700 ANSI Lumen typical (F6.0/F3.0)
30 to 85%
Overall Dimensions
Width is 20-1/4 inches (51.44cm)
Electrical Specifications
Height is 6- 3/4 inches (17.15cm) feet retracted
Height is 9- 1/2 inches (24.13cm) feet extended
Depth is 18- 13/16 inches (47.78cm) medium throw lens
Depth is 19- 1/16 inches (48.41cm) long throw lens
Video Inputs
2 - Component Analog Video (Y, Pb, Pr)
2 - HDMI Digital Video (1.1 Compliant)
McIntosh Data Control Input
1- 1/8 inch Stereo Mini Jack
Weight
40 pounds (18.14 kg) net, 54 pounds (24.5 kg) in shipping
carton
Power Control In
1 - 1/8” Stereo Mini Jack
Input voltage range 5V – 12V
Shipping Carton Dimensions
Width is 32 inches (81.28cm)
Depth is 28 inches (71.12cm)
Height is 13 inches (33.02cm)
Power Control Out
1- 1/8” Stereo Mini Jack
Output voltage 5V
Trigger Outputs
2- 1/8” Stereo Mini Jacks
Output Voltage 0V or 12VDC
Data Communications
Standard RS-232C
9pin D-Subminature female receptacle
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing Instructions
Packing Instructions
In the event it is necessary to repack the equipment for
shipment, the equipment must be packed exactly as shown
on this page, with the protective cover installed on the
projector lens. Failure to do this will result in shipping
damage.
Quantity Part Number Description
1
034374
Shipping carton complete
Use the original shipping carton and interior parts only
if they are all in good serviceable condition. If a shipping
carton or any of the interior part(s) are needed, please call
or write the Customer Service Department of McIntosh
Laboratory. Refer to page 4. Please see the Part List for the
correct part numbers.
CAUTION: To prevent possible damage to the Projec-
tor Lens Assembly, DO NOT at any time
attempt to LIFT, CARRY or RE-ORI-
ENT the Projector using the Lens.
Shipping
Carton
Top
Foam
Pad
Top
Protective
Lens Cover
Foam
Pad
Bottom
Shipping
Carton
Bottom
31
Download from Www.Somanuals.com. All Manuals Search And Download.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, NY 13903
The continuous improvement of its products is the
policy of McIntosh Laboratory Incorporated who
reserve the right to improve design without notice.
Printed in the U.S.A.
McIntosh Part No. 04101000
Download from Www.Somanuals.com. All Manuals Search And Download.
|