ELX8-60
Installation Guide
(v 1.0a)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notice
1. Do not p lace heavy objects on the top of the ELX8-60.
2. ELX8-60 is not weatherproof. In case of outdoor use, equip a weatherproof case to protect ELX8-60
from water, moisture, or temperature (higher or lower than specificat ions). To clean the ELX8 -60, gently
wipe the outside with a clean dry cloth.
3. Be sure to use a DC adapter that is provided by Rugged CCTV Connecting ELX8-60 directly to an AC
current will cause electric damages to ELX8-60.
4. Be careful not to drop the ELX8-60. Physical shocks may harm the product. In addition, be sure the
ELX8-60 is secured after installation.
5. ELX8-60 is made of metal. Therefore you can hurt human beings if yu throw it to them or hit on them.
When installing ELX8-60, be cautious to locate on safe places where children are unreachable.
6. If ELX8-60 does not operate properly, please contact the closest RUGGED CCTV distributor for after
sales service. Tampering or disassembling the product will void the warranty.
7. Security surveillance laws may differ for each country. Therefore, please contact the local region first
to avoid any surveillance law violations .
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
TABLE OF CONTENTS
OVERVIEW ..................................................................................................................................................................7
1. What is ELX8-60?.........................................................................................................................................7
2. Supplied Accessories ..................................................................................................................................8
3. Description & Function ................................................................................................................................9
INSTALLATION AND CONNECTION..............................................................................................................11
4. Connecting & Running ELX8-60............................................................................................................11
4.1. Connecting camera ...........................................................................................................................11
4.2. Connecting Monitor .......................................................................................................................... 12
4.3. Connecting Audio..............................................................................................................................12
4.4. Supplying Power ............................................................................................................................... 13
5. Running OSD menu .................................................................................................................................. 14
5.1. Using menu .........................................................................................................................................14
5.2. Dialogue Box to Edit a Word .........................................................................................................15
6. Setting remote controller .........................................................................................................................17
6.1. Setting remote control DIP switch ............................................................................................... 17
6.2. Setting ID of ELX8-60...................................................................................................................... 17
6.3. Selecting ELX8-60............................................................................................................................ 18
6.4. Operable range of remote controller .......................................................................................... 18
6.5. Loading the batteries into remote controller ............................................................................ 19
7. ELX8-60 Configuration .............................................................................................................................20
7.1. Basic Configuration .......................................................................................................................... 20
7.2. Advanced Configuration ................................................................................................................. 20
7.3. External Storage & Backup Configuration ................................................................................ 21
7.4. Internet/Intranet Configuration ...................................................................................................... 21
8.
ELX8-60 Basic Setting ........................................................................................................................... 22
8.1. Viewing Image .................................................................................................................................... 22
8.2. Setting Date & Time.........................................................................................................................23
8.2.1.
8.2.2.
8.2.3.
8.2.4.
8.2.5.
8.2.6.
8.2.7.
Time Zone...................................................................................................................................23
Daylight Saving.........................................................................................................................23
Sync with NTP........................................................................................................................... 23
Time Format............................................................................................................................... 24
Date............................................................................................................................................... 24
Time..............................................................................................................................................24
Apply Date/Time ....................................................................................................................... 24
4
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ELX8 -60
8.3. Setting Recording Condition .........................................................................................................24
8.3.1.
8.3.2.
8.3.3.
8.3.4.
8.3.5.
8.3.6.
8.3.7.
Configuration Status................................................................................................................ 25
Channel Status.......................................................................................................................... 25
Recording Speed/Quality....................................................................................................... 26
Speed(ips).................................................................................................................................. 26
Quality.......................................................................................................................................... 26
Audio Recording....................................................................................................................... 26
Apply.............................................................................................................................................26
9. Connecting and Configuring Sensor ...................................................................................................27
9.1. Connecting Sensor Input................................................................................................................ 27
9.2. Setting Sensor at OSD menu ....................................................................................................... 28
10.
10.1.
10.2.
Connecting & Configuring Relay Out..............................................................................................29
Connecting Relay Out................................................................................................................. 29
Configuring Relay Out................................................................................................................. 30
11.
Connecting External Device with Serial Port ............................................................................... 31
11.1.
Connecting Text Input Device (ATM / POS / Access Control)....................................... 31
12.
Connecting & Configuring Serial Ports for Pan/Tilt/Zoom ....................................................... 32
12.1.
Connecting Serial Port ................................................................................................................ 32
12.1.1.
Connecting RS232..............................................................................................................32
Connecting RS485..............................................................................................................32
Connecting RS422..............................................................................................................32
12.1.2.
12.1.3.
12.2.
Configuring Serial Port................................................................................................................ 33
Connecting USB Device...................................................................................................................... 34
Connecting External Storage............................................................................................................ 36
13.
14.
14.1.
14.2.
IEEE1394 Port ............................................................................................................................... 36
Connecting IEEE1394 Device.................................................................................................. 36
Available HDD ............................................................................................................................... 37
Registering & Formatting HDD ................................................................................................ 37
14.3.
14.4.
15.
15.1.
15.2.
Network Monitoring & Managing...................................................................................................... 38
Connecting Ethernet.................................................................................................................... 38
Configuring ELX8-60’s Network Information ....................................................................... 40
16.
16.1.
16.2.
Using DVR Manager.............................................................................................................................41
PC System Requirements for running DVR Manager ..................................................... 41
Installing DVR Manager .............................................................................................................41
Rugged CCTV
2003. 08. 13 (v 1.0)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
TABLE OF CONTENTS
16.3.
16.4.
16.5.
16.6.
Uninstalling DVR Manager ........................................................................................................43
Configstation.................................................................................................................................. 43
Monitor..............................................................................................................................................44
Playback .......................................................................................................................................... 44
APPENDIX ..............................................................................................................................................................45
#1.
#1.1.
#1.2.
HDD............................................................................................................................................................ 46
Fundamental Notions & Terms................................................................................................. 46
Installing HDD ................................................................................................................................ 48
Replacing HDD..............................................................................................................................60
Keeping Data ................................................................................................................................. 61
Caution in using HDD.................................................................................................................. 62
#1.3.
#1.4.
#1.5.
#2.
#3.
Using CD-ROM...................................................................................................................................... 63
Specification............................................................................................................................................ 64
6
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
ELX8 -60
OVERVIEW
1. What is ELX8-60?
The ELX8-60 is an 8-analog channels network digital video recorder. Video, Audio, and Text Event-Logs
are digitized and stored on two internal hard-drives.
Key features
q
q
q
q
q
8 analog video channels
1 channel audio recording &playback
Max. 60 / 50 ips (NTSC / PAL) recording speed
Realtime (30 / 25 ips for each channel) monitoring
Built-in software multiplexer for all 8 live monitoring channels (1 / 4 / 9 Ch Mode on CCTV Monitor
as well as PC)
q
q
q
q
q
q
q
q
q
q
Maximum 4TB storage capacity (IEEE 1394 for external HDD)
ATM/POS transaction information text recording and search with corresponding video
4 pairs of sensor inputs and alarm outputs
Built-in hardware motion detection with search function (64-division comparison)
Various efficient back-up methods (IEEE 1394(FiWi), Ethernet)
PTZ Control (Preset support) via RS 232 and RS 485/RS422
User-friendly 32bit True-colored Graphic OSD Menu
Dynamic IP (DHCP, Floating IP) support (when xDSL and Cable Modem are used)
IR remote controller (User controls PTZ with remote controller)
Remote Management Software (DVR Manager)
Rugged CCTV
2003. 08. 13 (v 1.0)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
OVERVIEW
2. Supplied Accessories
Unpack and check all the items as below.
1. ELX8-60 (1)
2. DC Power Supply (1)
(110V~220V)
3. AC Power Cord (1)
4. CD-ROM (Including DVR Manager) (1)
5. Remote Controller (1)
6. Guide (2)
7. Plug Bracket (1)
8. HDD Fixing Screw (8)
8
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
ELX8 -60
3. Description & Function
ELX8-60 Front
(1) LED
(2) IEEE1394 connecter
(3) Remote controller receiver
(4) USB connecter
(5) Function buttons
(6) Bracket fixing hole for rack mount
Rugged CCTV
2003. 08. 13 (v 1.0)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
OVERVIEW
ELX8-60 Rear
(7) Power switch
(8) Ethernet connector
(9) BNC connector for Video input
(10) Audio input / output connector
(11) RS232 connecter (9Pin D-Sub)
(12) Terminal block for RS232 & 422/485
(13) Terminal block for Sensor input
(14) Terminal block for Relay output
(15) Video output for MONITOR or VCR
(16) Video input type/impedance select & remote controller switch
(17) IEEE1394 connecter
(18) USB connecter
(19) Power connector (DC12V)
(20) GND
10
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
INSTALLATION AND CONNECTION
4. Connecting & Running ELX8-60
4.1. Connecting camera
(1) Set video type (NTSC/PAL) by rear panel ’s switch.
(2) Connect CCTV camera to ELX8-60 with BNC cable as shown below.
<Note>
The video type for all channels should be either NTSC or PAL. NTSC is the standard used in North
America.
Rugged CCTV
2003. 08. 13 (v 1.0)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
4.2. Connecting Monitor
(1) Connect CCTV monitor to ELX8-60 with BNC cable as shown below.
<Note>
ELX8-60 has two video output ports ; for Monitor and VCR. The output signals from the two ports are
same and either port may be used.
4.3. Connecting Audio
(1) Connect audio signal to ELX8 -60.
12
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
4.4. Supplying Power
(1) Connect power cable to ELX8 -60.
(2) Turn on the power switch located on the ELX8-60 rear panel.
<Note>
Use the plug bracket to secure the power cable if needed.
<Note>
To connect EARTH, refer to the following picture.
Rugged CCTV
2003. 08. 13 (v 1.0)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
5. Running OSD menu
5.1. Using menu
Press the [MENU] button to open the OSD Configuration Menu.
(1) Main Menu
(2) Sub-menu
(3) Setting Page
(4) Help message
(1) Main Menu Tabs: The select ed tab is shown in blue and the related sub-menus will be shown below
the tab. To move to the previous/next Main Menu Tab, use the [
sub-menu, press the [ENTER] or [ ] buttons.
/
] arrow buttons. To move to a
(2) Sub-menu: The select ed sub -menu is shown in blue and the related setting page will be shown to the
right of the sub-menu. Use the [ / ] arrow button s to move within the sub-menu list. To move to the
setting page press the [ENTER] button. To exit the setting page, press the [EXIT] button.
(3) Setting Page : The select ed item is shown in gray. To move within each page, use the [
/
] or
[ / ] arrow buttons. Press the [ENTER] button to change the value of a setting. When the setting value is
a word, a dialogue box to edit the word will open. When setting value is a number, it should be set with
using the [
/
] or [ / ] arrow buttons. After the value is set, press the [EXIT] button. To exit the
Setting Page, press the [EXIT] button.
(4) Help message : Related information for each menu/setting will be displayed here.
14
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
5.2. Dialogue Box to Edit a Word
There are two methods to set word.
(1) Using number button
“ ”
Enter the related numbers in order of horizontal/vertical . (For example, in order to select C , press [3]
and [2] buttons.)
(2) Using arrow button
Select a value using the [
/
] or [ / ] buttons. The intersection of the horizontal and vertical bar
is select ed value. Press the [ ] button to confirm the selected value.
Rugged CCTV
2003. 08. 13 (v 1.0)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
(3) Function word
The following symbols are for executing specific functions:
ü
1#2.1 : Enter
: Back Space & delete
: Space
: Move to left
: Move to right
: Previous Code Page
: Next Code Page
16
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
6. Setting remote controller
6.1. Setting remote control DIP switch
Set the remote control DIP switch t o “ON .”
6.2. Setting ID of ELX8-60
When controlling sever al ELX8-60s with one remote controller, set Remote Control ID as follows.
(1) Press the [MENU] button.
(2) Select “System” with using [
(3) Select “Miscellaneous” from the sub-menu list using the [ ] button and press the [ENETR] button.
] button and press the [ENETR] or [ ] button.
Rugged CCTV
2003. 08. 13 (v 1.0)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
(4) Select “Remote Control ID,” and press the [ENETR] button.
(5) Select a value using the [ ] buttons and pressthe [EXIT] button.
/
(6) Press the [EXIT] button toexit the Settings Page and return to Monitor mode.
<Note> Remote Control ID
Up to 16 ELX8-60s can be controlled with a single remote controller.
6.3. Selecting ELX8-60
If several ELX8-60s are set with unique ID numbers, they can be controlled with one remote controller.
To select a specific ELX8-60, press the ID button of remote controller until the 8 LEDs on the front of the
ELX8-60 light up and a buzzer sounds.
<Note>
Because remote controller ID is sixteen, ELX8-60 will correspond.
6.4. Operable range of remote controller
18
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
6.5. Loading the batteries into remote controller
Remote controller requires two AAA-type batteries.
2. Taking care that the poles(+/-)
1. Remove the battery cover.
3. Replace the battery cover.
are correctly positioned
<Note>
Batteries are not included as a packing accessory.
Rugged CCTV
2003. 08. 13 (v 1.0)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
7. ELX8-60 Configuration
7.1. Basic Configuration
7.2. Advanced Configuration
20
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
7.3. External Storage & Backup Configuration
7.4. Internet/Intranet Configuration
Rugged CCTV
2003. 08. 13 (v 1.0)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
8. ELX8-60 Basic Setting
8.1. Viewing Image
After initial start-up, images from Ch.1~4 are displayed in a quad-split screen.
<Note>
If user password is set, a prompt for entering the password will appear.
22
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
8.2. Setting Date & Time
(1) Press [MENU] button, and select “Quick Setup ” tab.
(2) Select “Date/Time” and enter the Settings Page by pressing [ENTER].
8.2.1. Time Zone
(1) Select “Time Zone” and press [ENETR] button to configure.
(2) Select a value using the [
/
] button and press the [EXIT] button when finished.
8.2.2. Daylight Saving
(1) “Daylight Saving Time” is only activated for time zones that use Daylight Savings. If activated, press
[ENTER] to enter a new value.
(2) Select “On/Off” using the [
/
] button and press the [EXIT] button when finished.
8.2.3. Sync with NTP
In order to synchronize time with NTP (Network Time Protocol) server, select “On”.
(1) Select “Sync with NTP ” using the [ ] or the [ / ] buttons and press [ENTER] button.
/
(2) Select “On/Off” using the [
/
] button and press the [EXIT] button.
Rugged CCTV
2003. 08. 13 (v 1.0)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
8.2.4. Time Format
(1) Select “Time Format” using the [
/
] or the [ / ] buttons and press [ENTER].
(2) Two Time Formats are available; ‘MM/DD/YYYY’ and ‘YYYY/MM/DD’. Select a value using [ / ]
buttons, and press the [EXIT] button when finished. (Default value is ‘MM/DD/YYYY’.)
8.2.5. Date
(1) Select “Date” using the [
/
] or the [ / ] buttons and press [ENTER].
] buttons, and select t he value using the [ / ]
(2) Select ‘MM’/‘DD’/‘YYYY’ using the [
buttons.
/
(3) Press the [EXIT] button when finished.
8.2.6. Time
(1) Select “Time” using the [
/
] or the [ / ] buttons and press [ENTER].
(2) Select ‘HH’/‘MM’ using the [
/
] buttons, and select t he value usingthe [ / ] buttons.
(3) Press the [EXIT] button when finished.
8.2.7. Apply Date/Time
Most setting values are applied automatically, when exiting from the related menu page. But “Date”
& “Time” settings are not applied automatically because theymay critically affect the file system of
the recorded HDD. To apply Date/Time setting s confirm settings with [Apply Date/Time] button.
(1) Select “Apply Date/time” using the [
message will appear.
/
] or the [ / ] buttons and press [ENTER]. A warning
(2) Select “OK” using the [
[EXIT] button.
/
] or the [ / ] buttons and press [ENTER]. To cancel, press the
8.3. Setting Recording Condition
Recording conditions under the “Quick Setup ” menu tab apply the same values to all analog channels 1~8.
All settings are applied for 24 hours /day regardless of the values set for “Time Schedule” or “Alarm Rec. ”
24
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
(1) Press [MENU] button, and select “Quick Setup .”
(2) Move to sub-menu by pressing [ENTER] orthe [ ] button.
(3) Select “Recording” using the [ / ] buttons and pressthe [ENTER] button.
8.3.1. Configuration Status
Displays the recording configuration status. When setting up through the “Quick Setup ” menu, “Quick
Setup” will be shown. When setting up through “Normal Rec. ” or “Alarm Rec.,” “Custom Setup” will be
shown.
<Note>
Only when all the 16 channels' normal recording conditions are set through M' acro Setup' and
maintained, it is marked as 'Macro Setup'. Otherwise, it will be marked as 'Custom Setup '.
8.3.2. Channel Status
(1) Select “Channel Status ” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
Rugged CCTV
2003. 08. 13 (v 1.0)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
8.3.3. Recording Speed/Quality
(1) Select “Recording Speed/Quality” using [ / ] buttons and pressthe [ENTER] button.
(2) Select a value using the [ ] button. Press the [EXIT] button when finished.
/
<Note> Recording Speed/Quality means
Low : Speed=1ips and Quality=Q5
Std. : Speed=5ips and Quality=Q5
High : Speed=15ips and Quality=Q5
Custom : Speed and Quality = Manually defined by User.
8.3.4. Speed(ips)
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Speed ” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.5. Quality
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Quality” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.6. Audio Recording
(1) Select “Audio Recording” using [ / ] buttons and pressthe [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.7. Apply
(1) Select “Apply ” using [ / ] buttons and press the [ENTER] button.
(2) Setting values are applied and the previous menu will be displayed.
26
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
9. Connecting and Configuring Sensor
9.1. Connecting Sensor Input
To connect a sensor to S1, fix the wire to “S1” and “G“.
<Note>
Devices connected to the sensor input should have “Dry contact .” The following diagram is of an
electric circuit with approximately 12mA flows.
Rugged CCTV
2003. 08. 13 (v 1.0)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
9.2. Setting Sensor at OSD menu
(1) After a sensor is connect ed, it can be activated through the OSD Configuration menu.
(2) Select the sensor number (S1, S2, etc.) and press the [Enter] button to configure. Use the [
] buttons to select “On” or “Off.” Press [EXIT] when finished.
/
(3) When activated, the “Pre / Post Alarm” function will cause the ELX8-60 to record images at the
specified Speed and Quality for a length of time before and/or after the sensor is triggered.
28
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
10. Connecting & Configuring Relay Out
10.1. Connecting Relay Out
ELX8-60 has total four ports of Relay Out.
To connect a device to “O1 ,” connect the wires to two “O1”s.
<Note>
The rated voltage and current of Relay Out are as follows. Do not exceed the rated values.
24V DC, 1.25A, 30W
Maximum Switching Capacity
125V DC, 0.24A, 30W
125V AC, 0.5A, 62.5VA
Rugged CCTV
2003. 08. 13 (v 1.0)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
10.2. Configuring Relay Out
Each relay can be synchronized with a sensor input or with motion detection for each of the four time
schedules (Weekday (Day), Weekday (Night), Weekend (Day), Weekend (Night)). Relays can also be
controlled locally by pressing the [SEARCH/RELAY] button followed by the relay number (1-4). Relays
can also be controlled remotely through the “DVR Manager software.”
30
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
11. Connecting External Device with Serial Port
11.1. Connecting Text Input Device (ATM / POS / Access Control)
In addition to images, the ELX8 -60 can record text data received from POS/ATM through the RS232
serial port.
Connect RS232 to 9pin D-sub of ELX8 -60, and configure the “Text ” sub-menu under the “System” tab.
Set “Serial Setup ” under the “System” menu tab to “RS232” and “Device” to “Text.” The baud rate may
differ for each device; consult the device manual for more information.
<Note>
Befor e installingany external device, consult with the local RUGGED CCTV distributor. Some external
devices may not be compatible with the ELX8-60.
Rugged CCTV
2003. 08. 13 (v 1.0)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom
12.1. Connecting Serial Port
The ELX8 -60 has most major PTZ protocols already pre-programmed. Makes and models not supported
can still be controlled using the Transparent Protocol. For a list of supported protocols, refer to the list on
the OSD Configuration menu.
12.1.1. Connecting RS232
Fix the wire to 1~3 pins (RX, TX, GND).
12.1.2. Connecting RS485
Fix the wire to 4~5 pins and 8 pin (R+, R-,GND).
12.1.3. Connecting RS422
Fix the wire to 4~8 pins (R+, R-, T+, T-, GND).
32
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
12.2. Configuring Serial Port
Configure PTZ serial ports and available modes at “System / Serial Setup ”.
After completing serial setup, configure base address and port for each channel under the “Camera” menu
tab . When connecting PTZ devices to several cameras, be sure the base address matches the address for
the camera.
Rugged CCTV
2003. 08. 13 (v 1.0)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
<Note> Wire Handling
Trimming Wire
When connect ing awire to a terminal block, follow the instructions below. Note the different types of
wire that can be used.
Stranded Wire: Peel off the wiring cover
8~10mm and solder it. Wire gage should be
AWG 22 ~ 26.
Solid Wire: Peel off the wiring cover 8~10mm
and solder it. Wire gage should be AWG 20 ~
26.
Inserting & removing wire
To insert the wire, use a screwdriver as
shown in the diagr am to the right.
13. Connecting USB Device
USB port can be used to copy up to 1 minute of images to aUSB Flash memory disk. When connecting
USB device, do not exceed the rated values of USB device.
USB Spec.
Available Device
Output Voltage/Current
Ver 1.1 (Max 12M bps)
USB M emory Stick,
Max. 200mA per DC 5V / Port
<Note>
The disk should be formatted with FAT32 type.
34
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
If properly connected, the disk is recognized automatically as in the following picture. To copy images,
the process is as follows: Set copy range (up to 1 minute) à Select drive à Copy (press “Start”) .
<Note>
USB Flash products that require a Windows program to operate may not be recognized by the ELX8 -
60.
Rugged CCTV
2003. 08. 13 (v 1.0)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
14. Connecting External Storage
14.1. IEEE1394 Port
ELX8-60 has two IEEE1394 ports for external storage device interface. With them, ELX8-60 can expand
storage capacity up to 4TB.
<Note>
Some IEEE1394 Bay may not be recognized by the ELX8 -60. Before purchasing, consult the local
RUGGED CCTV distributor.
14.2. Connecting IEEE1394 Device
When using FireWire supported external HDD, hard drive bays can be connected to 1 port in the front
panel or 1 port in the rear panel. The ELX8 -60 does not supply power to the hard drive bay; therefore
only bays that use external power can be used.
<Note>
ELX8-60 detects external HDD, even though ELX8 -60 runs. If not, it is recommended to connect as
follows.
1. Power off ELX8-60.
2. Connect external HDD to IEEE1394 port.
3. Power on external device.
4. Power on ELX8-60.
36
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
14.3. Available HDD
It is recommended to use the following HDD models with the ELX8 -60. If a non-recommended HDD is
used, Rugged CCTVwill not guarantee the warranty.
Manufacturer : MAXTOR
Series
Model No
6Y060L0
Size
60GB
Series
Model No
Size
60GB
4R060L0
4R080L0
4R120L0
6Y080L(P)0
6Y120L(P)0
80GB
80GB
DiamondMax
Plus 9
DiamondMax
16
120GB
120GB
6Y160L(P)0
6Y200P0
160GB
200GB
250GB
4R160L0
160GB
(7200rpm)
(5400rpm)
6Y2 50P0
<Note>
Buffer for DiamondMax Plus 9 ’s model “L” is 3MB; for model “P” the buffer is 8MB.
14.4. Registering & Formatting HDD
“Disk Manager” will automatically run on start-up after installing a HDD.
If “Disk Manager” does not automatically run on start-up, make sure the HDD is properly installed.
Rugged CCTV
2003. 08. 13 (v 1.0)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
(1) Press [ENTER] button at “Select Disk”.
(2) Select new added HDD (indicated as “[F] ”) using [ / ] button and press [EXIT] button
(3) Select “Action” using [ / ] buttonand press [EXIT] button.
(4) Select “Add” using [
/
] button and press [EXIT] button.
(5) Select “Apply ” using [ / ] button and press [EXIT] button. The HDD status is changed to “[*] ”.
(6) Select “Action” using [ / ] button and press [EXIT] button.
(7) Select “Format ” using [
/
] button and press [EXIT] button.
(8) Select “Apply ” using [ / ] button and press [EXIT] button. The HDD status is changed to “[R]”
after formatting.
(9) Shut down “Disk Manager” by pressing [EXIT] button.
15. Network Monitoring & Managing
ELX8-60 can be accessed, controlled, and managed from remote site via Internet/Intranet.
15.1. Connecting Ethernet
(1) Turn off ELX8-60’s power switch.
(2) Connect ELX8 -60 to hub with Ethernet cable.
(3) Turn on ELX8-60’s power switch.
38
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
<Note>
ELX8 -60
1. Supply power to ELX8-60 after connecting Ethernet cable to protect against electrical damage to
ELX8-60.
2. Check cable connection status.
3. Check LED on ELX8 -60’s rear panel after supplying power.
Rugged CCTV
2003. 08. 13 (v 1.0)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
15.2. Configuring ELX8-60 Network Information
The following description is on based on Ethernet connection. For more detailed information on the
Network Settings Page, please refer to “ELX8 -60 OSD User’s Guide”.
(1) Press [MENU] button.
(2) Select “System” using the [
/
] buttons and press [ENTER].
(3) Select “Network” using the [ / ] buttons and press [ENTER].
(4) Select “IP Addr” using the [ / ] buttons and press [ENTER].
(5) Press [EXIT] button after entering IP address in the dialogue box.
(6) Select “Net Mask” using the [ / ] buttons and press [ENTER].
(7) Press [EXIT] button after entering Net Mask in the dialogue box.
(8) Select “Gateway ” using the [ / ] buttons and press [ENTER].
(9) Press [EXIT] button after entering Gateway in the dialogue box.
(10) Select “DNS” using the [ / ] buttons and press [ENTER].
(11) Press [EXIT] button after entering DNS in the dialogue box.
(12) Press [EXIT] button to exit the page.
40
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
16. Using DVR Manager
16.1. PC System Requirements for running DVR Manager
Minimal Requirements
P- 600MHz or above
128 MB or above
Recommended Requirements
CPU
P- 1GHz or above
256 MB or above
RAM
VGA
16 MB or above
32 MB or above
OS
Windows 2000/XP
Windows 2000/XP
Resolution
Network
1024 X 768 pixels or above
100 Base TX Fast Ethernet
1024 X 768 pixels or above
100 Base TX Fast Ethernet
16.2. Installing DVR Manager
(1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC
(2) Doubleclick the DVR Manager setup file. Install Shield Wizard will be automatically installed.
(3) Click the “I Agree” button to accept the license agreement
Rugged CCTV
2003. 08. 13 (v 1.0)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
(4) Select which component s to install and press the “Next ” button.
(5) Browse and choose a directory if the default directory is not preferred. Click the “Install” button,
after selecting a directory to install.
(6) Click the “Close” button after DVR Manager program is installed successfully.
42
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX8 -60
16.3. Uninstalling DVR Manager
(1) Click Windows “Start” Button.
(2) Select and Click‘Uninstall’ icon to run Uninstall Shield.
(3) DVR Manager program will be automatically deleted.
16.4. Configstation
Click icon on desktop to run “DVR Manager Configstation” program.
Rugged CCTV
2003. 08. 13 (v 1.0)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
INSTALLATION AND CONNECTION
16.5. Monitor
Click the related icon and run the “DVR ManagerMonitor” program.
16.6. Playback
Click the related icon and run the “DVR Manager Playback ” program.
44
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
APPENDIX
APPENDIX
Rugged CCTV
2003. 08. 13 (v 1.0)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
#1. HDD
#1.1. Fundamental Notions & Terms
ELX8-60 Storing Constructure
(1) It is possible to connect 2 sets of HDD internally (Internal, ATA Interface) and 63 sets of HDD
externally (External, 2 ports of IEEE1394).
(2) All of the connected HDDs is recognized as one virtual disk, and ELX8-60 supports upto 4TB.
(3) Hdds are divided into primary disk (connected firstly) and auxillary disk.
<Note>
ATA(or EIDE) supports two channel interfaces (Primary/Secondary). Each channel can be connected to
two devices (Mas ter/Slave, HDD/CD-ROM). However ELX8-60 supports 1 channel interface internally
and total two HDDs. In order to prevent confusing VFS2’s Primary Disk, we will not use the terms
(Primary/Secondary).
(4) Primary disk is composed of log partition, normal partition, and alarm partition, and auxillary disk is
composed of only no rmal partition. So if primary disk has some problem, all of the recorded data will
be lost.
<Note>
Log Partition
To store the information of recorded data
Normal Partition
Alarm Partition
To store the data as normal recording schedule
To store the data as alarm recording condition (MD or Sensor)
46
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Backup
(1) Backup is possible only through IEEE1394 port, and HDD for backup should be formatted as FAT32
type. (Its type is indicated as [F] in Disk Manager.)
Disk Manager
(1) When HDD is added or deleted physically, Disk Manager runs automatically after rebooting. If not,
you can run “Disk Manager” manually with moving “MenuàUtilityàDisk Manager”.
(2) HDD Type at Disk Manager
[R]
[V]
Available of recording
Connected and formatted as ELX8 -60’s file system. If using ‘Add used ’ command, it
will be changed to [R]. There is no need to reformat.
Connected but not available file system. After using ‘Add’, need to format for making as
[R].
[F]
[*]
[X]
Connected and added using the ‘ADD’ command. If formatting, it will be [R].
If there is a disk of [*], DVR will record nothing.
HDD cable is not connected or has some problem. In case of that, HDD should be
removed with using ‘Confirm Removed’ menu.
IntA
IntB
Internal Master HDD
Internal Slave HDD
Ext
External HDD
Rugged CCTV
2003. 08. 13 (v 1.0)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
(3) HDD Managing Command
Format
Add
Format as ELX8-60’s file system. Not availableto PC file system.
Add HDD for recording. Need to format.
Add Used
Add a HDD that has been used and formatted. There is no need to reformat. It is
possble only when HDD is added as Primary Disk.
Remove
Remove current HDD. HDD can be reused without data loss by the ‘Add Used ’
command.
Confirm Removed
Used when a removed HDD is still listed. ALL DATA WILL BE LOST!
#1.2. Installing HDD
Compatible HDD
It is recommended to use the following HDD models with the ELX8 -60. If a non-recommended HDD is
used, Rugged CCTVwill not guarantee the warranty.
Manufacturer : MAXTOR
Series
Model No.
6Y060L0
Size
Series
Model No.
4R060L0
4R080L0
4R120L0
4R160L0
Size
60GB
80GB
120GB
160GB
60GB
80GB
120GB
160GB
6Y080L(P)0
6Y120L(P)0
6Y160L(P)0
DiamondMax
Plus 9
DiamondMax
16
(7200rpm)
(5400rpm)
6Y200P0
6Y2 50P0
200GB
250GB
L series of DiamondMax Plus 9 has 2MB buffer memory, while P model has 8MB
48
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Installing & Expanding Internal HDD
Adding or replacing HDD should follow below process.
(1) Turn off the power of ELX8-60.
(2) Check whether the dip switches are set as illustrated below
(3) Remove the 6 screws as illustrated below and pull up the cover from the rear part to open.
(4) Take out power and data cable of HDD from Main PCB ASS’Y. Remove 4 HDD Bracket screws and
take out HDD ASS’Y.
Rugged CCTV
2003. 08. 13 (v 1.0)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
(5) Fix the HDD with provided screws. Connect power and data cables to HDD.
Installing single HDD
Installing 2 HDDs
Caution for HDD Management
1. Replacing ‘SLAVE’ HDD of internal 2 HDDs causes permanent data loss in the SLAVE HDD.
2. MASTER HDD has all the index of stored data including ‘SLAVE’ HDD. Corruption on
‘MASTER’ HDD may cause total data loss. Be careful when h andling the main HDD.
3. It is strongly recommended that all data within HDDs should be backed up before replacing.
50
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
(6) Connect HDD power cable to main PCB ASS’Y. Secure the HDD with screws.
(7) Connect HDD cable ’s connector to HDD as in the following picture.
(8) Assemble the top cover.
Rugged CCTV
2003. 08. 13 (v 1.0)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
When installing one primary disk
(1) When power is supplied to ELX8 -60, “Disk Manager” runs automatically after rebooting. If not, run it
manually in “MenuàUtilityàDisk Manager”.
(2) There is a HDD that is indicated as “[F] IntA”. Select it.
(3) Press the “Apply ” button after selecting action as “Add”. Then [F] is changed to [*].
(4) Press the “Apply ” button after selecting action as “Format ” and setting the size of alarm partition.
Then [*] is changed to [R].
<Note>
Alarm partition can be set from 10% to 90% within the size of primary disk.
(5) Press the [EXIT] button to shut down “Disk Manager”. (If recording schedule is set, ELX8-60 will
start recording.)
52
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
When installing one primary disk and auxiliary disk
(1) When power is supplied to ELX8 -60, “Disk Manager” runs automatically after rebooting. If not, run it
manually in “MenuàUtilityàDisk Manager”.
(2) There is a HDD that is indicated as “[F] IntA”.
(3) Select a HDD for installing as primary disk. (IntA or IntB)
(3) Press the “Apply ” button after selecting action as “Add”. Then [F] is changed to [*]. If IntB is added
as primary disk, it will be placed at upper list.
(5) Select a HDD for installing as auxiliary disk.
(6) Press the “Apply ” button after selecting action as “Add”. Then [F] is changed to [*].
(7) Select a primary disk, and press the “Apply ” button after selecting action as “Format” and setting the
size of alarm partition. Then [*] is changed to [R].
(8) Select an auxiliary disk, and press the “Apply ” button after selecting action as “Format” and setting
the size of alarm partition. Then [*] is changed to [R].
<Note>
Alarm partition can be set at only primary disk. So it is indicated as “Disable” in case of formatting.
(9) Press the [EXIT] button to shut down “Disk Manager”. (If recording schedule is set, ELX8-60 will
start recording.)
Rugged CCTV
2003. 08. 13 (v 1.0)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
Expending External HDD (When using internal HDD as primary disk)
ELX8-60 use IEEE1394 as external storage device interface, and has two ports of IEEE1394. ELX8 -60
supports upto 4TB storage.
<Note>
1. Some IEEE1394 ports may not be recognized by the ELX8-60. Before purchasing, consult the local
RUGGED CCTV distributor.
2. External storage should use external power.
3. For connection and setup of IEEE1394, please refer to the manual of related device.
Connect IEEE1394 interface cable as follows.
54
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
When using Disk Farm
The following description is when ELX8-60 has internal primary disk and 3 sets of IEEE1394 HDD.
(1) When external HDD farm is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
<Note>
If connecting the device that is used in ELX8-60, type will be indicated as [V].
(3) Select a third HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4) Select a fourth HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(5) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(6) Select a third HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*] is
changed to [R].
(7) Select a fourth HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*]
is changed to [R].
(8) Press t he [EXIT] button to shut down “Disk Manager”.
Rugged CCTV
2003. 08. 13 (v 1.0)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
When using RAID
The following description is when ELX8-60 has internal primary disk and 1 set of IEEE1394 HDD.
<Note RAID>
Even though several HDDs are connected to RAID, ELX8 -60 will recognize them as only one HDD.
For connection and setup of RAID, please refer to the manual of related device.
(1) When external HDD RAID is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
à
à
run it manually in “Menu Utility Disk Manager”.
(2) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
<Note>
If connecting the device that is used in ELX8-60, type will be indicated as [V].
(3) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(4) Press the [EXIT] button to shut down “Disk Manager”.
56
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Installing & Expending External HDD (When using external HDD as
primary disk)
When using Disk Farm
The following description is when ELX8-60 does n’t have internal primary disk and 4 sets of IEEE1394
HDD.
(1) When external HDD farm is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a first HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
<Note>
It is when ExtA is added as primary disk.
If connecting the device that is used in ELX8-60, type will be indicated as [V].
(3) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4) Select a third HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(5) Select a fourth HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(6) Select a first HDD of [*] Ext . Press the “Apply ” button after selecting action as “Format ”. Then [*] is
changed to [R].
(7) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
Rugged CCTV
2003. 08. 13 (v 1.0)
57
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
is changed to [R].
(8) Select a third HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*] is
changed to [R].
(9) Select a fourth HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*]
is changed to [R].
(10) Press the [EXIT] button to shut down “Disk Manager”.
When using RAID
The following description is when ELX8-60 does’t have internal primary disk and 2 sets of IEEE1394
HDD.
(1) When external HDD RAID is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a first HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
<Note>
It is when ExtA is added as primary disk.
If connecting the device that is used in ELX8-60, type will be indicated as [V].
(2) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4)
Select a first HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(5)
Select a second HDD of [*] Ext . Press the “Apply ” button after selecting action as “Format ”. Then
[*] is changed to [R].
58
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
(6) Press the [EXIT] button to shut down “Disk Manager”.
Rugged CCTV
2003. 08. 13 (v 1.0)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
#1.3. Replacing HDD
Checking HDD
ELX8-60 file system (VFS2) sensors bad sector automatically, and the sensored bad sector is not used.
The following means when HDD is broken or has some problem in connection.
(1) When replaying is stopped or ELX8-60 is rebooted in specific playback range.
(2) When image searching per event is impossible.
(3) When recording is stopped and “Disk Manager” shows HDD type as [X]
When primary disk is broken
When primary disk is broken, all of the connected HDD data can’t be used. So the broken HDD should be
replaced and all connected HDDs should be reinstalled in “Disk Manager”. (“Remove” -> “Add” ->
“Format ”).
When auxiliary disk is broken
The broken auxiliary disk should be replaced and reinstalled in “Disk Manager”. (“Add” -> “Format ”).
60
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
#1.4. Keeping Data
To keep the stored data, you should back up or reserve as HDD itself.
Backup
(1) Connect backup HDD to IEEE1394 port.
(2) Go to playback mode with pressing the [Playback] button.
(3) Press the [SELECT] button and then [MENU] button.
(4) Run “Backup Manager” with selecting the “Backup Data” menu.
(5) Set backup range and press the “Start ” button after selecting backup HDD.
<Note>
1. Backup HDD should be formatted as FAT32 type.
2. Backup data can be replayed with specific S/W, DVR Manager or MiniPlayer.
3. Backup data is made as “*.re3” file. If file size is over 2GB, it may not be recognized normally.
4. In course of backup, “Auto Delete” function doesn’t run. If HDD is full, recording ma be stopped
instantly.
5. For more detailed information of DVR Manager’s backup, please refer to the “DVR Manager User’s
Guide”.
Rugged CCTV
2003. 08. 13 (v 1.0)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
How to preserve as HDD itself
To keep HDD itself, it is possible only when HDD is installed and used in ELX8-60 (including primary
disk and RAID).
And it is recommended to use external HDD instead of internal HDD. Namely, connect only one external
HDD, and then keep it after data is full.
<Note>
The preserved HDD’s data is possible to replaying only when it is connected to ELX8-60.
#1.5. Caution in using HDD
For handling or guaranteeing HDD, RUGGED CCTV follows HDD guaranty condition. RUGGED
CCTV doesn’t bear the responsibility about data loss by user’s mistake in operating.
62
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
#2. Using CD-ROM
Components of CD- ROM disc
Installation Guide
User’s Guide
:
:
ELX8 -60 Installation Guide
ELX8 -60 User’s Guide
: DVR Manager User’s Guide
(ELX8-60 Remote Management Program)
: Version 5.1
DVR Manager
Acrobat Reader
Preparation
To read manual of CD-ROM disc, Adobe Acrobat 5.0 should be installed in client’s PC.
<Note>
If Adobe Acrobat Reader is not installed within client’s PC, use the Acrobat Reader program of CD-
ROM.
Reading manual of CD-ROM
Follow the steps to read user’s guide.
(1) Insert the supplied CD-ROM into CD-ROM drive of PC.
Open the user’s guide, PDF file.
Rugged CCTV
2003. 08. 13 (v 1.0)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
#3. Specification
General
CPU
32bit RISC Processor (200MIPS)
8MB
Flash Memory
Main Memory
OS
64MB
Embedded LINUX
Video Channel
Storage Device
8 Analog Channel (NTSC or PAL)
Internal 3.5” IDE HDD 2EA (default 1EA)
External 2EA for IEEE1394 Interface
Support Max. 4Tbytes
Intelligent File System
Data-loss protection against power failure
Image Compression
Technology
Differential Wavelet
Average File Size
1~5KB (Standard Quality)
Image Quality Level
Image Compression Rate
Recording Speed
5 Level
20:1~500:1
60 ips/50 ips(NTSC/PAL) 7.5 ips/8ch or 30 ips/2ch
Network
Browser
DVR Manager
Protocol
TCP/IP, ARP, ICMP, DHCP, FTP, PPPoE
10/100Mbps Ethernet (RJ-45)
Firmware upgrade via Network
Monitoring : Max. 5 Users
Connector
S/W Upgrade
Simultaneous Users
Playback : Max. 5 Users
Security
Password (User or Administrator Authenticantion)
Watermarking (Against image forging)
64
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Display
Monitoring
Max. 240/200ips (NTSC/PAL)
Viewer
1ch, 4ch, 9ch, Auto Sequential
Max. 60 ips for local channel : max 7.5 ips/channel
720x243(NTSC), 720x288(PAL)
Max. 60ips
Recording Performance
Recording Resolution
Playback Performance
Playback Speed
Function
1x, 2x, 4x, 8x, 16x (Forward & Reverse Play)
Step-Forward, Step-Reverse
Environment
Operation Temperature
Storage Temperature
Operation Humidity
Storage Humidity
5~45 C
-10~55 C
30~80%, free of condensation
93% below, free of condensation
Data Backup/Expansion/Copy
HDD Expandable Data Backup
Analogue VCR
IEEE1394
VHS Video output for VCR
Daily / Weekly / Monthly
USB Flash memory disk
Backup Reminder
Data Copy
Input/Output
Video
1 Monitor output via BNC
1 Video output via BNC
Audio
1 I nput : Line-in, 1 Vpp (20dB off : 0.1 Vpp)
1 Output : Line-out, 1Vpp
Level : -7~8(16 Step) Recording level
AMP : 20dB amplifier for low level audio
Monitoring : Local and remote
4 Relay outputs (Max DC 30W, AC 62.5VA)
Daily : Day / Night
Digital Output
Digital Output Schedule
Weekly : Weekdays / Weekends
Conditions : MD, Sensor inputs
4 Sensor inputs (Support Dry contact)
Sensor Input
Rugged CCTV
2003. 08. 13 (v 1.0)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
PTZ Control
Serial Port
RS232(1), RS485(1)/ RS422(1)
Front panel button & IR remote controller
(control IP video channel as well)
On -the-screen PTZ control on PC
8 points preset per channel
Control Method (Local)
Control Method (Remote)
Preset Mode
Group Mode
1 group per channel
Others
Digital Zoom
2x (Live & PlayBack Mode)
Motion Detection or Sensor input
Alarm triggered Video Data Preservation
Log search
Alarm Trigger
Alarm Data Preservation
Alarm Log
Log monitoring via OSD & Network
Pre : 1~10 seconds
Pre/Post Alarm
Post : 1~60 seconds
Schedule Recording
Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : Normal / Event
Text Data Recording
Multilingual Menu
POS/ATM transaction information archived along with
corresponding video data
English, German, French, Spanish, Japanese
Electricity
Power (Applied Adaptor)
DC 12V
Consumption Current
Max 4.5A (Internal 2 HDD)
Typical 2.9A (Internal 2 HDD)
Max. 54W
Consumption Voltage
Typical 35W
66
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Mechanical
Dimension (W D H)
Weight
306 x 280 x 67(mm)
3.5Kg (With one HDD)
Rugged CCTV
2003. 08. 13 (v 1.0)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX8 -60
APPENDIX
68
2003. 08. 13 (v 1.0)
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX8 -60
Rugged CCTV
5327 Cedar Creek Dr.
Kemp, Texas 75143
Tel : (866) 301-2288
Fax : (903) 498-8989
Technical Support: 1-866 -301-CCTV
E-mail: [email protected]
Rugged CCTV
2003. 08. 13 (v 1.0)
69
Download from Www.Somanuals.com. All Manuals Search And Download.
|