Maxtor DVR 4 Channel Digital Video Recorder User Manual

Thank you for purchasing our product.

Please read this User’s Manual before

using the product. Change without Notice

4 Channel Digital Video Recorder

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

About this document

Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users

Manual. Pay particular attention to the parts that are marked NOTICE.

Also, when connecting with external application, first turn the power OFF and follow manual

instruction for appropriate installation.

Before reading this document

1. This document is intended for both the administrator and users of stand alone DVR Model.

2. This manual contains information for configuring, managing and using stand alone DVR Model.

3. To prevent fire or electrical shock, do not expose the product to heat or moisture

4. Be sure to read this manual before using stand alone DVR Model.

5. For questions and technical assistance of this product, contact your local dealer.

►Strong recommendation on installation of the DVR unit

1. Check electricity at the place you want to install the DVR unit is stable and meets our electricity

requirements.

Unstable electricity will cause malfunction of the unit or give critical damage to the unit.

2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat,

and it must be properly discharged.

Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close up an

opening (fresh air in-take) on the right side of the unit..

3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit.

When it is installed inside 19 inch mounting rack together with other devices, please check built-in

ventilation fan of the rack is properly running.

Download from Www.Somanuals.com. All Manuals Search And Download.

Content

Safety Precautions………………………………………………………………………………………………… 2

About this document………………………………………………………………………………………………. 3

Before reading this document……………………………………………………………………………………. 3

Unite Description of Front Panel………………………………………………………………………………… 5

Unit Description of Rear Panel……………………………………………………………………………………6

Installation………………………………………………………………………………………………………….. 7

Function Setup…………………………………………………………………………………………………….. 15

Basic Operation…………………………………………………………………………………………….. 4

USB Data Read and Networking………………………………………………………………………………... 39

Record Time Table: 80 GB HD………………………………………………………………………………….. 49

VGA Description (Optional) ……………………………………………………………………………………… 50

Additional…………………………………………………………………………………………………………….51

Download from Www.Somanuals.com. All Manuals Search And Download.

Unit Description of Front Panel

4 split screen

1 ~ 4 full screen / password

Sequence / Freezer / Zoom / Water Mark(PTZ mode) / Information

MENU button / PLAY button / REC. record button LOCK key lock button

BACKUP data back up button / T-SRH time search playback button

ESC function exit button

Value change button

Direction UP / Down,

Direction Left / Right

Record and play stop,

Playback pause / steps.

Playback forward or reverse.

ENTER / Audio ON or OFF

Function LED light display

Playback forward / reverse

Function item change shuttle.

Remote controller IR

USB. Data backup or firmware update

Download from Www.Somanuals.com. All Manuals Search And Download.

Unit Description of Rear Panel

Power cord in 12V/5A, power switcher (ON / OFF)

Camera 1 ~ 4 in and

looping out

75 Ohm ON/OFF (high/low adjust)

VGA output. PC monitor connector.

(Optional)

VG A

Audio channel

input x 1 and output x 1

Main Monitor

S-Video (Y/C) monitor

RS-485

LAN. Network connector

Control keyboard connector

RS-232 connector (ISP. For RD control)

Alarm connector

Notice: Reboot DVR after installing any device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Procedure

1) Camera Connection

Connect the camera to the CAMERA INPUT

on the Rear Panel of the 4 CH DVR.

CH4

CH1

CH2

CH3

MONITOR

NOTICE: Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND, and it is

recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit.

Internal Circuit

Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V.

5) Network Connection

DVR connects to LAN

ETHERNET

rks

TERATRAY CONNECTION

◆To view video image on the computer through internet with DVR view software.

Download from Www.Somanuals.com. All Manuals Search And Download.

5) HDD connection

How to connect single HDD

How to connect 2 HDD

I/O BOARD

MASTER

HDD1

tie

MASTER

HDD

MAIN BOARD

SLAVE

HDD2

Set the drive jumpers as specified by hard disk drive manufacturer.

1. Make sure the HDD is MASTER.

2. Make sure the cable connector is

correct.

1. Make sure the HDD is MASTER and

SLAVE.

2. Make sure the cable connector is

correct.

3. Please check the HDD panel for

Master set up.

Please check the HDD panel for

Master and Slave set up.

Notice:

-Hard Disk Master and Slave jumper pin must right, otherwise it makes DVR work fault.

Hard Disk testing table:

Brand

Seagate

IBM

Model

Barracuda

DeskStar

Caviar

Capacity

80 GB

Notice

80 GB

WD2000

Hitachi

Maxtor

200 GB

80 GB

DeskStar

MaxLineII

300 GB

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture

Full screen or split screen display

Press

button, to display 4 split screen.

Press numeric buttons

to display the desired camera image in full screen.

1.) FREEZE Mode

1. In live mode press

(FREEZE) button to freeze image.

2. Press

again to cancel freeze mode.

2.) Zoom Mode(Display Enlargement.)

Go to full screen mode with numeric buttons at live or playback

mode, then press ZOOM button to display screen Enlargement.

Use

button to move position.

3.) Auto Mode

Press

(AUTO) button to start screen auto sequencing, and press it again to cancel auto mode.

4.) W.MARK. Water Mark mode.

Water Mark on to check if the data has modify.

5.) INFO (System Information). Auto disappear after 2 minutes if no any button operating.

** SYSTEM INFORMATION **

1. Network IP address

1.IP ADDR:

2. Network IP gateway

2.GATEWAY:

3. Network IP netmask

3.NETMASK:

4. Network user amount

4.NET USER:

5. Hard disk capacity

5.HDD SIZE:

6. Hard disk used percentage

6.HDD USED:

7. First hard disk status

7.STATUS1

8. Video format

8.STATUS2

9. System running time

9.UPTIME

10. System version

10.VERSION:

Download from Www.Somanuals.com. All Manuals Search And Download.

6.) BACKUP. Image backup mode.(Image back up must be done on playback mode only.)

Locate the playback point of which you want. Press BACKUP, back up menu shows:

CDRW / USB

CDRW

BACKUP MENU

USB

BACKUP MENU

CDR WRITE SPEED

START BACKUP TO CDR

FORMAT USB

CDR WRITE SPEED x1,x2,x3

START BACKUP TO CDR

FORMAT USB

START BACKUP TO USB

USB:

The BACKUP CAUTION window pop-up. Press ENTER to begin data back up. Capacity of USB device is not

limit.

On playback mode, presses BACKUP:

Lower-Right corner of the screen:

** BACKUP CAUTION **

THE ORIGINAL BACKUP FILE

WILL BE KILLED.

PRESS [ENTER] TO BACKUP.

PRESS [BACKUP] TO CANCEL.

xxx K

xxx K (Presently back up progress)

Important:

If DVR cannot detect USB device, please format it to FAT or FAT 32 on PC OS.

When the file is opened from a CF card, only DVR images will appear, but without sounds.

Additional:

During playback, USB device is full or user press BACKUP button screen display a “PAUSE” caption, User

takes out the USB device to computer USB slot then save data to hard disk. After re-insert USB device to

DVR slot, user press BACKUP again. Press ENTER to continue backup or backup button to cancel.

** BACKUP CAUTION **

PAUSE

THE ORIGINAL BACKUP FILE

WILL BE KILLED.

PRESS [ENTER] TO BACKUP.

PRESS [BACKUP] TO CANCEL.

PS: NetViewer software auto copied to USB device when data backup. See the USB Data Read and

Networking pages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Compatible USB: Transcend 256 MB, 1 GB / A-DATA, 512MB / USB Flash Drive 128 MB /

Intelligent Stick 256 MB / SOLOMON 128 MB / ISTEC 1GB.

CD-RW:

xxx K (Presently back up progress)

Press BACKUP to stop saving. Or wait for CD is full done.

Data only read in Netviewer.

xxx K

7.) Key Lock function

>On the Live mode, press

(lock), Only, numeric, freeze, auto, and zoom buttons could work.

Press lock key again to enter the login-in window. Enter admin or user password to unlock.

Key lock function only accept password correct log in even re-boot DVR power.

8.) AUDIO function ))))

))))

xxxxxxxxx

ENTER / AUDIO button

Audio playback: AUDIO ,

))))))displays on the Upper-left of screen. At that time, audio

will playback. Press it again to turn it off.

Notice

Audio playback only on normal( x 1 ) playback.

9. NETWORK Playing

NETWORK PLAYING

PASSWORD : (*****)

ENTER PASSWORD TO TERMINATE

1. When the admin do playback mode on AP (Net Viewer), user can terminate it after into password of DVR.

On AP client, admin needs to connect again.

2. When AP on playback mode, DVR is on playback mode also.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

1. Playback Mode

PLAY

1) Press

button to begin playback. (System playback the images backward)

MAIN PLAY PAGE

2. T-SRH button

1) T-SRH: Playback by time search.

1.MASTER TIME LIST

2.SLAVE TIME LIST

3.MASTER EVENT LIST

4.SLAVE EVENT LIST

5.GOTO DATE: 2004/12/31

6.GOTO TIME: 12:12

7.GOTO PLAY

Press T-SRH button to active playback function.

Press direction button

UP/DOWN to choose

items.

1) TIME LIST (Playback image by Time-Search): Recorded images list (by hours)

TIME LIST

Y / M / D H : M

Y / M / D H : M (Beginning of recording time)

Every playback data list displays by an hour.

Y / M / D H : M (End of recording time)

No page display limit. 10 items display on each page.

Press direction button UP/DOWN to choose items.

Press values change button to change to previous / next page.

Notice:

Every playback data list displays by an hour, but if user finds out like:

1. 10:00 ~ 10:12

2. 10:12 ~ 11:00

Reason: 1. Hard disk is full. 2. User change record mode setup.

Download from Www.Somanuals.com. All Manuals Search And Download.

2) EVENT LIST (Alarm List): Event source- Video loss / Alarm trigger / Motion / Record

EVENT LIST +10

NO Y / M / D H : M CH EVENT

10 items display on each page / Total 5000 items display for 500 pages. When event list is out of compass,

the total items are less then 5000.

NO Y / M / D H : M CH EVENT

>Event happens time and list.

CH: Event Channel Display.

>1 CH ~ 4 CH

+10 : Display pages by 10 units / +100 : Display pages by 100 units / +1000 : Display pages by 1000 units.

- Press direction button left and right to change +10 / +100 / +1000

Event type.

>Includes Motion / Alarm / V-Loss / Record / Power On / Event Full / Network (Network total users,

include log in and log out.)

Press direction button UP/DOWN to choose items.

Press

values change button to change page. Press ENTER to start

playback.

>Special time search playback:

Go TO DATE：２００２／１２／１２

-Choose year / month / day

>Press direction button Left / Right to choose items, press values change button

GOTO TIME：１２：１２

to change value.

-Choose hour and minute

>Press direction button Left / Right to choose items, press values change button

GOTO PLAY

-Press ENTER button to start playback.

Notice: Playback speed change by

or shuttle. Speed is x 1, x 2, x 4, x 8, x 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Setup

1) Press

button to enter into menu. You could do the system function setup in MENU.

2) Password enter window pop-up:

CHECK PASSWORD MENU

PASSWORD (*****)

Default password (Account-Admin) : 44444

Default password (Account-User) : 11111

3) Press numeric (1 ~ 10 )button or remote controller ( 1 ~ 10 )to choose password.

4) Remote controller function buttons are same as DVR panel function buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operation

Press MENU button to enter MAIN SETUP PAGE.

MAIN SETUP PAGE

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

5. BUZZER

6. RELAY

SETUP

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC: EXIT, ENTER: RUN

1) Use direction button up/down

button to select setup item.

2) Press

button to enter into sub-menu function setup.

3) Press sub-menu item with direction button up/down

or left/right button.

And change the value with

values change button or turn inner-shuttle.

4) Press ESC to go back to main / sub menu or exit menu.

Notice:

1. ADMIN level can setup all DVR menu functions.

2. USER level cannot setup ADVANCED page of DVR main menu function.

3. Auto disappear after 4 minutes if no any button operating.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. HDD INFORMATION

MAIN SETUP PAGE

POSITION SIZE USED BRAND

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

MASTER

LAST TIME

SLAVE

5. BUZZER

6. RELAY

SETUP

LAST TIME

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC: EXIT,

:PAGE

MENU, ESC: EXIT, ENTER: RUN

- 2 hard disk information display.

Information display: POSITION SIZE USED BRAND

>POSITON: Master / Slave

>SIZE: Hard Disk capacity. xxGB. Maximum display is 999MB

>USED: 00 ~ 100 %. Hard disk overwrites 100 ~ 199 %.

>BRAND: DVR auto detect hard disk brand.

>LAST TIME: The last record time display.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. DATE-TIME SETUP

MAIN SETUP PAGE

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

DATE-TIME SETUP PAGE

1. DATE 2000 / 00 / 00

2. TIME

3. FORMAT

5. BUZZER

6. RELAY

SETUP

3. DISPLAY AT xx LINE(S)

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC:EXIT,

:MODIFY

MENU, ESC: EXIT, ENTER: RUN

1. DATE

2. TIME: > Use direction button up/down choose position, values change button to change date and time

values. Do not need to stop hard disk working (Play or record).

3. FORMAT:

YY/MM/DD, MM/DD/YY, DD/MM/YY, YY/ENG/DD, ENG/DD/YY, DD/ENG/YY, YYYY/MM/DD,

MM/DD/YYYY, DD/MM/YYYY, YYYY/ENG/DD, ENG/DD/YYYY, DD/ENG/YYYY.

Y=Year. M=Month. D=Day. ENG=Month display in English.

4. DISPLAY AT xx LINE(S)

-Date and Time position on screen xx line(s). 00 ~ 23.

-. Day and time change

Press direction button up/down/left/right to choose items or move date-time position.

Press

values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. DISPLAY SETUP

MAIN SETUP PAGE

DISPLAY SETUP PAGE

1. DATE-TIME

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

2. CAMERA TITLE

3. PB DATE-TIME

4. PB CAMERA TITLE

5. BUZZER

6. RELAY

SETUP

5. PB DUMMY CAMERA ON

6. DVR STATUS

7. SYSTEM SETUP

8. ADVANCED SETUP

7. BORDER COLOR

WHITE

MENU, ESC:EXIT,

:MODIFY

MENU, ESC: EXIT, ENTER: RUN

1. DATE-TIME: Date and Time caption display mode on or off setup.

>ON / OFF

2. CAMERA TITLE: Camera Title caption display mode on or off setup.

>ON / OFF

3. PB DATE-TIME: Play back date and time caption display mode on or off setup.

>ON / OFF

4. PB CAMERA TITLE: Play back camera title caption display mode on or off setup.

>ON / OFF

5. PB DUMMY CAMERA: To clear dummy image if channel input not up to 4.

>ON / OFF

6. DVR STATUS: DVR system, record, playback, audio caption display mode on or off setup.

>ON / OFF

7. BORDER COLOR: Border color WHITE / DARK / BLACK / GRAY.

Press direction button up/down to choose the desired item.

Press

values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. CAMERA SETUP

MAIN SETUP PAGE

CAMERA SETUP PAGE

1. COLOR SETUP

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

2. TITLE SETUP

3. SCREEN POSITION SETUP

4. V-LOSS DISPLAY SETUP

5. VIDEO MASK SETUP

5. BUZZER

6. RELAY

SETUP

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC: EXIT, ENTER: RUN

>>DEFAULT RESET<<

MENU,ESC:EXIT,

71.66068 Tm(EXIT)Tj0 10.02 33

(2.) TITLE SETUP: Input TITLE of each camera. 9 characters can be input.

TITLE SETUP PAGE

CAMERA SETUP

CH 01 (01

CH 02 (02

CH 03 (03

CH 04 (04

)

1. COLOR SETUP

2. TITLE SETUP

3. SCREEN POSITION SETUP

4. V-LOSS DISPLAY SETUP

5. VIDEO MASK SETUP

MENU, ESC: EXIT:

: MODIFY

Press direction button up/down/left/right to choose items and position.

Press

values change button to change values.

Characters choose:

Space:

Numeric: 0 / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9

Capital letter: A / B / C / D / E / F / G / H / I / J / K / L / M / N / O / P / Q / R / S / T / U / V / W / X / Y / Z

Download from Www.Somanuals.com. All Manuals Search And Download.

(3.) SCREEN POSITION SETUP

**** SCREEN POSITION****

CAMERA SETUP

1. COLOR SETUP

LEFT

RIGHT

2. TITLE SETUP

3. SCREEN POSITION SETUP

4. V-LOSS DISPLAY SETUP

5. VIDEO MASK SETUP

DOWN

ENTER : DEFAULT

ESC

: QUIT

Press direction buttons up/down/left/right to move screen position.

2. Press ENTER button for default.

3. Press ESC button to quit.

Download from Www.Somanuals.com. All Manuals Search And Download.

(4.) V-LOSS DISPLAY SETUP

VLOSS SETUP PAGE

**V-LOSS FUNCTION:

CAMERA SETUP

1. COLOR SETUP

2. TITLE SETUP

CH 01 : ON

CH 02 : ON

CH 03 : ON

CH 04 : ON

3. SCREEN POSITION SETUP

4. V-LOSS DISPLAY SETUP

5. VIDEO MASK SETUP

MENU, ESC: EXIT:

: MODIFY

** V-LOSS FUNCTION: ON / OFF

CH 01 : ON / OFF

CH 02 : ON / OFF

CH 03 : ON / OFF

CH 04 : ON / OFF

PS. If choose on, X icon displays beside camera title.

Press direction buttons up/down/left/right to choose items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

(5.) VIDEO MASK SETUP

VIDEO MASK SETUP PAGE

**VIDEO MASK FUNCTION:

CAMERA SETUP

1. COLOR SETUP

2. TITLE SETUP

CH 01

CH 02

CH 03

CH 04

3. SCREEN POSITION SETUP

4. V-LOSS DISPLAY SETUP

5. VIDEO MASK SETUP

MENU, ESC: EXIT:

: MODIFY

**VIDEO MASK FUNCTION: ON / OFF

CH 01 : ON / OFF

CH 02 : ON / OFF

CH 03 : ON / OFF

CH 04 : ON / OFF

MASK means the channel would not display on the live screen, but still can set it on recording.

Press direction buttons up/down/left/right to choose items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. BUZZER SETUP

MAIN SETUP PAGE

BUZZER SETUP PAGE

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

**BUZZER FUNCTION ON

BUTTON BUZZER

ALARM BUZZER

MOTION BUZZER

V-LOSS BUZZER

HDD-FULL BUZZER

CRASH BUZZER

5. BUZZER

SETUP

6. RELAY

SETUP

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC: EXIT:

: MODIFY

MENU, ESC: EXIT, ENTER: RUN

**BUZZER FUNCTION: All buzzer function

>ON / OFF

1. BUTTON BUZZER?

> ON / OFF

2. ALARM BUZZER?

> ON / OFF

3. MOTION BUZZER?

> ON / OFF

4. VLOSS BUZZER?

> ON / OFF

5. HDD-FULL?

> ON / OFF (Buzzer on if hard disk record only once(Record setupÆ HDD FULLÆSTOP REC.)

6. CRASH?

> ON / OFF (Buzzer on if DVR system or hard disk crash.)

Press direction buttons up/down to BUZZER SETUP items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. RELAY SETUP

MAIN SETUP PAGE

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

RELAY SETUP PAGE

**RELAY FUNCTION: ON

1. ALARM

2. MOTION

3. V-LOSS

RELAY: ON

5. BUZZER

SETUP

4. HDD-FULL RELAY: ON

5. CRASH RELAY: ON

6. RELAY

SETUP

7. SYSTEM SETUP

8. ADVANCED SETUP

MENU, ESC: EXIT, ENTER: RUN

**RELAY FUNCTION: ON

1. ALARM

2. MOTION

3. VLOSS

RELAY: ON

4. HDD FULL RELAY: ON (Relay on if hard disk record only once.)

Record setupÆ HDD FULLÆSTOP REC.

5. CRASH

RELAY: ON (Relay on if DVR system or hard disk crash.)

Press direction buttons up/down to each item.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. SYSTEM SETUP

MAIN SETUP PAGE

SYSTEM SETUP

1. DWELL INTERVAL

2. LANGUAGE

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

3. VIDEO INPUT

4. RS-485 ID

5. BUZZER

6. RELAY

SETUP

5. RS-485 PROTOCOL

6. RS-485 BAUD RATE

7. SYSTEM SETUP

UPTIME: xx HRS

MENU, ESC: EXIT: : MODIFY

8. ADVANCED SETUP

MENU, ESC: EXIT, ENTER: RUN

SYSTEM SETUP

1. DWELL INTERVAL:

- 0 ~ 999SEC. Full channel and call monitor auto sequence time.

2. LANGUAGE:

ENGLISH / CHINESE / JAPANESE / FRENCH

After change language, user needs to exit menu. Language would change next time back to menu.

3. VIDEO INPUT: NTSC / PAL system detection.

AUTO / NTSC / PAL

User needs to re power on after change.

4. RS-485 ID:

- 01 ~ 4

5. RS-485 PROTOCOL

- KEYB / LILIN / PELCO-P / PELCO-D / NICECAM / DENTEC-D / DENTEC-P

6. RS-485 BAUD RATE

- 1200 / 2400 / 4800 / 9600

-UPTIME: xx HRS. This means the total system working time after DVR first power on.

RS-485 ID and protocol is the command for system control keyboard. If user has no keyboard to

control then does not have to care.

Press direction buttons up/down to choose items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

8. ADVANCED SETUP

MAIN SETUP PAGE

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

1. HDD INFORMATION

2. DATE-TIME SETUP

3. DISPLAY SETUP

4. CAMERA SETUP

5. BUZZER

6. RELAY

SETUP

7. SYSTEM SETUP

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

8. ADVANCED SETUP

MENU, ESC: EXIT, ENTER: RUN

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

ALARM SETUP PAGE

1. ALARM FUNCTION

2. ALARM DURATION

3. ALARM RELAY SETUP

4. ALARM POLARITY SETUP

MENU, ESC: EXIT:

: MODIFY

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

1. Alarm function: ON / OFF. Alarm function on or off depends on alarm device includes in DVR system.

2. Alarm duration: 10 ~ 999. Alarm buzzer and record duration time.

ALARM RELAY SETUP

>ALARM 01 ~ ALARM 04: ON / OFF

Even choose on, but RELAY SETUPÆAlarm relay or relay function off, this function is still closed.

ALARM POLARITY SETUP

>ALARM 01 ~ ALARM 4: N.O. / N.C. / OFF

Press direction buttons up/down to choose items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. MOTION SETUP

MOTION SETUP PAGE

**MOTION FUNCTION ON

**MOTION DURATION

**CHANNEL NUMBER

1. SENSITIVITY

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

2. VELOCITY

3. ACTIVATION

4. RELAY

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

5. MOTION AREA SETUP

MENU, ESC: EXIT:

: MODIFY

MOTION SETUP

**MOTION FUNCTION (For all channels)

-ON / OFF

**MOTION DURATION

-10 ~ 999. Motion buzzer and record duration time.

**CHANNEL NUMBER

-CH 01 ~ 04

1. SENSITIVITY Adjusts motion Detection Sensitivity.

-1 ~ 32 (low Æhigh)

2. VELOCITY Adjusts motion object slow /fast speed detection

-1 ~ 10 (slow speedÆfast speed)

3. ACTIVATION (For each channel)

-ON / OFF. The function only for channel motion detect active, not for motion record per each.

4. RELAY

-ON / OFF

Even choose on, but RELAY SETUPÆMotion relay or relay function off, this function is still closed.

5. >MOTION AREA SETUP<

Press direction buttons up/down to choose items.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

> MOTION AREA SETUP <

All area detect with factory default. Press ENTER button to change mode and then increase or reduce.

For example:

Clear lattices

Press value change button to reduce.

Press value change button

3. RECORD SETUP

ADVANCED SETUP PAGE

RECORD SETUP

1. HDD FULL

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

2. RECORD SPEED

3. RECORD MODE

4. RECORD AUDIO

5. QUALITY

6. SCHEDULE SETUP

7. CHANNEL SETUP

MENU, ESC: EXIT:

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

: MODIFY

RECORD SETUP

HDD FULL: When hard disk is full, DVR next step is kept overwrite record or stop record?

-OVERWRITE / STOP REC

Notice: STOP REC：One hard disk record full, stop record. Two hard disk, both of them record full,

stop record.

Record process

OVERWRITE

STOP REC

M(99%), S(0%) Æ M(100%), S(0%)

To second and record To second and record

M(99%), S(100%) Æ M(100%), S(100%) To second and record To second and record

M(0%), S(99%) Æ M(0%), S(100%)

To first and record

Stop record

M(100%), S(99%) Æ M(100%), S(100%) To first and record

Notice:

When hard disk is full, system buzzer on, and then presses ENTER to stop. Next to press REC, over write

message window popup.

"** OVERWRITE CAUTION **"

"THE HDD ARE BOTH FULL,"

"RECORDING WILL DELETE"

"THE OLD IMAGE."

Press ENTER to continue record.

Over write from the first data area.

Press MENU to exit.

"PRESS [ENTER] TO OVERWRITE."

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORD SPEED: Record FPS setup

-1/30(1/30), 1/15(1/15), 1/10(1/10), 1/5 (1/5), 1/3 (1/3), 1/2 (1/2), 1(1), 2(2), 3(3.13), 5(5), 10 (8.33),

15(12.5), 30(25), 60(50), 120(100). NTSC / (PAL)

RECORD MODE: Record mode setup.

-ALWAYS / SCHEDULE / EVENT / EVENT ON SCHEDULE / EVENT + SCHEDULE

RECORD AUDIO: Audio record setup

-ON / OFF. (Suggest not fewer than 5 fps.)

QUALITY: Record image quality setup

- SUPER / HIGH / FINE / NORMAL / LOW

SCHEDULE SETUP

CHANNEL SETUP: CH01 ~ CH04 record on or off.

Press direction buttons up/down to choose item.

Press values change button to change values.

Additional:

2. RECORD SPEED. 1/30(1/30), 1/15(1/15), 1/10(1/10), 1/5 (1/5), 1/3 (1/3), 1/2 (1/2), 1(1), 2(2), 3(3.13), 5(5),

10 (8.33), 15(12.5), 30(25), 60(50), 120(100).

- 120 is the maximum fps. Full screen playback with 120 frames per each.

- Split screen playback with 60 frames.

3. RECORD MODE. ALWAYS / SCHEDULE / EVENT / EVENT ON SCHEDULE / EVENT + SCHEDULE.

- Always: 24 hours recording.

- Schedule: Date and time schedule recording mode.

- Event: Alarm / Motion / V-Loss event mode recording. (Whatever which channel event, all channel record.)

- Event on schedule: Event record only on schedule time.

- Event + Schedule: Except event on schedule recording, it would still do record if event happens not on

schedule time.

Notice:

After record mode setup, user needs to press REC button to start. Set on Always mode, DVR do record if user

presses REC. Other record mode would ready on DVR idle status.

4. RECORD AUDIO: ON / OFF.

-Choose on, DVR would do audio recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

>SCHEDULE SETUP<

RECORD SETUP

1. HDD FULL

Press direction buttons up/down to

SCHEDULE items.

2. RECORD SPEED

3. RECORD MODE

4. RECORD AUDIO

5. QUALITY

Press values change button to change values.

6. SCHEDULE SETUP

7. CHANNEL SETUP

Factory default is everyday all schedules time on

recording.

SCHEDULE SETUP

CURSOR STEP

SUN

30MIN / 6MIN

MON

TUE

WED

THU

FRI

SAT

Press direction buttons up/down/left/right to see

date and time difference.

Press values change left/right button to change 30MIN or 6 MIN

++ / - - : Increase / Reduce. Every day record with factory default.

On , use up/down button to choose date, press button to change on

+ + or - -. After, use direction left / right button to start increase or reduce time area.

Mode function button

+ + increase

- - reduce

Download from Www.Somanuals.com. All Manuals Search And Download.

30MIN

SCHEDULE SETUP

CURSOR STEP

SUN

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

MON

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

TUE

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

WED

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

THU

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

FRI

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

SAT

00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00

00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30

For example:

TUE ~ SAT, all day schedule time recording, but SUN 07:00 ~ 22:00 and MON 01:30 ~ 11:30

do schedule recording. User can press ENTER to see the schedule time area difference.

Download from Www.Somanuals.com. All Manuals Search And Download.

7) RECORD CHANNEL SETUP PAGE

RECORD SETUP

1. HDD FULL

RECORD CHANNEL SETUP PAGE

2. RECORD SPEED

3. RECORD MODE

4. RECORD AUDIO

5. QUALITY

CH 01

CH 02

CH 03

CH 04

6. SCHEDULE SETUP

7. CHANNEL SETUP

MENU, ESC: EXIT:

: MODIFY

CH 01 : ON / OFF

CH 02 : ON / OFF

CH 03 : ON / OFF

CH 04 : ON / OFF

PS. Choose off if no video input channel or which channel would not do record.

According to channel record, record time would different.

Press direction buttons up/down to choose item.

Press values change button to change values.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. PASSWORD SETUP

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

PASSWORD SETUP PAGE

1. LEVEL:(

2. ADMIN:(

3. USER :(

)

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

Press direction buttons up/down/left/right to

Choose items position.

LEVEL (Log In level ID type setup)

>NONE / ADMIN / USER

-ADMIN

-USER

Press values change button to change values.

-NONE, user does not need to insert password before enter in MENU.

ADMIN password

>44444 (Factory Default)

Notice:

Password always 5 character input, cannot < 5 characters

USER password

>11111 (Factory Default)

Press direction buttons up/down/left/right to choose items position.

Press numeric (1 ~ 10 )button or remote controller ( 1 ~ 10 )to choose

Notice:

1. ADMIN level can setup all DVR menu functions.

2. USER level cannot setup ADVANCED page of DVR main menu function.

3. Auto disappear after 4 minutes if no any manual operate.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. NETWORK SETUP

ADVANCED SETUP PAGE

TCP-IP SETUP PAGE

1. SPEED:>512K

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

2. DVR NAME:[dvr16]

3. NET TYPE: OFF

4. STATIC IP SETUP

5. PPPOE ID SETUP

6. DNS/DDNS SETUP

7. SERVER PORT SETUP

MAC ADDR: xx.xx.xx.xx.xx.xx

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

1. SPEED : >512K / 512K / 256K / 128K / 64K

> Upload speed. Choose the close speed by applied.

2. DVR NAME: [ x 15 space ]

3. NET TYPE: STATIC / DHCP / PPPOE / OFF

4. STATIC IP SETUP

Press direction buttons up/down/left/right to

TCP-IP items position.

5. PPPOE ID SETUP

6. DNS/DDNS SETUP

7. SERVER PORT SETUP

Press values change button to change values.

-MAC ADDR

XX.XX.XX. Machine number, user cannot change.

2. DVR NAME: see DDNS apply.

3. NET TYPE:

> choose network connecting type as user.

4. STATIC IP SETUP:

> Depends on LAN or WAN. Input value witch get from network technician or ISP company.

> Advice user apply network speed Upload 512K / Download 512K, to avoid image data too big influence the

remote quality. The network traffic jam always make data transfer slow, it is normal.

STATIC IP SETUP

1. IP ADDR: 192.168.192.250

2. GATEWAY: 192.168.192.254

3. NETMASK: 255.255.255.000

4. INTERNAL MAPPING: OFF

Internal Mapping:

LAN IP corresponding

Download from Www.Somanuals.com. All Manuals Search And Download.

5. PPPOE ID SETUP

If users apply the dynamic IP from ISP, then should input ID and password that from ISP information

list. And then go to set DNS/DDNS SETUP

For example:

Address name is [email protected]

Password is 654321

PPPOE ID SETUP

1. LOGIN ID: [ x 20 space]

1. LOGIN ID: [ [email protected]]

:[ x 20 space]

]

3. PASSWORD: [ x 20 space]

4. CLEAR PPPOE SETUP

3. PASSWORD: [ 654321]

4. CLEAR PPPOE SETUP

Notice:

PPPOE ID SETUP

1. Please “CLEAR PPPOE SETUP”

if data is changed.

1. LOGIN ID: [ 123456

]

:[ @hinet.net.tw]

2. PASSWORD shows “*” icon.

3. PASSWORD: [ 654321]

4. CLEAR PPPOE SETUP

7. SERVER PORT SETUP

SERVER PORT SETUP

1. W.W.W: 0080

For IE. (feature)

1. W.W.W: 0080

2. VIDEO : 0021

For AP(Net Viewer)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. DNS/DDNS SETUP

Whatever user apply a free or pay DDNS, user needs to input every thing below.

DDNS apply: User can get a free hostname or pay from website below.

1. http://www.3322.net/ (China)

2. http://www.changeip.org/

3. http://www.dyndns.com/

4. http://www.no-ip.com/

5. http://www.dhs.org/

6. http://www.dtdns.com/index.cfm?fuseaction=info.hosts

For example:

Go to: http://www.dtdns.com/index.cfm?fuseaction=info.hosts

Click sign up to create an account.

Download from Www.Somanuals.com. All Manuals Search And Download.

Fill your information to sign up paper.

After, go to email account to get activate ID and code.

Click here to active

Download from Www.Somanuals.com. All Manuals Search And Download.

Fill ID and code.

Click hostnames

Download from Www.Somanuals.com. All Manuals Search And Download.

Type Hostname and choose a domain name, and then click Add Hostname.

EX: Hostname = Myhostname, Domain = 4irc.com

After click Add Hostname>>

Download from Www.Somanuals.com. All Manuals Search And Download.

Data confirm done, then you can go to DVR advanced setupÆ Network setup now.

Advanced setup Æ TCP-IP SETUP

TCP-IP SETUP PAGE

1. SPEED:>512K

TCP-IP SETUP PAGE

1. SPEED:>512K

DTDNS hostname

2. DVR NAME:[dvr16]

3. NET TYPE: OFF

2. DVR NAME:[Myhostname

3. NET TYPE: OFF

]

4. STATIC IP SETUP

5. PPPOE ID SETUP

6. DNS/DDNS SETUP

7. SERVER PORT SETUP

MAC ADDR: xx.xx.xx.xx.xx.xx

4. STATIC IP SETUP

5. PPPOE ID SETUP

6. DNS/DDNS SETUP

7. SERVER PORT SETUP

MAC ADDR: xx.xx.xx.xx.xx.xx

Download from Www.Somanuals.com. All Manuals Search And Download.

6. DNS/DDNS SETUP

DNS/DDNS SETUP

1. D.N.S 1: 000.000.000.000

2. D.N.S 2: 000.000.000.000

3. SERVER : DHS

9. D.N.S 1: 000.000.000.000

10. D.N.S 2: 000.000.000.000

11. SERVER : DTDNS

4. DOMAIN: [ x 20 space]

5. LOGIN ID:[ x 20 space]

12. DOMAIN: [ 4irc.com

]

13. LOGIN ID:[ your DTNS long in name

]

:[ x 20 space]

14.

]

7. PASSWORD: [ x 20 space]

8. CLEAR DDNS SETUP

15. PASSWORD: [your DTNS long in password

16. CLEAR DDNS SETUP

]

Important:

PASSWORD: This is your DTDNS apply login password, not Activation Code!

Download from Www.Somanuals.com. All Manuals Search And Download.

6. HDD FORMAT

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

Press direction buttons up/down to

HDD FORMAT items position.

Press ENTER to format all HDD.

Caution: User can format HDD only when

all HDD stop record or playback.

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

Æ HDD FORMAT CAUTION!! :

** HDD FORMAT CAUTION!!**

ALL DATA IN HDD WILL BE

DESTROYED!!

Press ENTER button to format hard disk.

PRESS [ENTER] TO FORMAT.

PRESS [ESC] TO CANCEL.

Press ESC button to cancel hard disk format.

Notice:

New hard disk detect: When DVR power, system would detect new hard disk install. If the hard disk is in

different format, then the message popup. User needs to press ENTER to format, if press MENU, and then

this hard disk would not be detected.

** NEW HDD CAUTION **"

"THE NEW HDD IS DETECTED."

Press FORMAT to format.

"FORMAT THE NEW HDD??"

Press MENU to exit.

"PRESS [ENTER] TO FORMAT."

"PRESS [MENU] TO CANCEL."

Download from Www.Somanuals.com. All Manuals Search And Download.

7. FACTORY DEFAULT

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

Press direction buttons up/down to

FACTORY DEFAULT items position.

Press ENTER to restore.

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

** CAUTION!! **

Press ENTER button to restore.

Press ESC button to cancel.

ALL SETUP VALUE WILL BE CLEAR,

AND RESTORE FACTORY DEFAULT!!

PRESS [ENTER] TO RESTORE.

PRESS [ESC] TO CANCEL.

8. SOFTWARE UPDATE

ADVANCED SETUP PAGE

1. ALARM SETUP

2. MOTION SETUP

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

6. HDD FORMAT

SOFTWARE UPDATE

UPDATE METHOD:

START UPDATE

7. FACTORY DEFAULT

8. SOFTWARE UPDATE

UPDATE METHOD: USB / HTTP / UNIX

USB: Copy firmware to USB device, and then plug in DVR USB interface. Choose START UPDATE and then

press ENTER to start. Or save the update version to USB device, DVR system would do data update

automatically. USB ERROR displays if no any USB device plug.

NETWORK: Press START UPDATE to link. 80 Port must open in your network server.

UNIX: For R&D testing.

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Data Read and Networking

1. Windows 2000 / XP, select small character display.

2. Resolution 1024 x 768.

3. RAM up to 128 MB, system up to PIII-800.

4. Double click SETUP.EXE of CD, and then start to install.

5. User can go to company server to download AP software.

6. Browse install path and then click Next.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Advice resolution 1024 x 768. According computer equipment, please choose suitable resolution

8. Select Start Menu Folder, and then click Next.

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Click create a desktop icon or not, select DVR type, and then click Next.

4 CH and 16 CH DVR Net viewer is suitable. Only some split screen can not display.

10. Click INSTALL to start install.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Click Launch NetViewer and click Finish to done.

Download from Www.Somanuals.com. All Manuals Search And Download.

12. Click Setting.

Name: Name the IP address position.(Each name and IP saves every different input)

1 ~ 16 full screen select.

IP Addr: Input DVR IP address.

Full / Quad / 9 split / 16 split

6 split / 8 split / 10 split / 13 split

AVI codec: Different computer equipment; different AVI format.

Microsoft Windows Media video 9 is better.

Or Cinepak Codec by Radius(Slow transmission, better quality) /

Microsoft Video 1(Fast transmission, bad quality).

Video: Fullsize, Halfsize: screen size choose.

NTSC, PAL. Frame/Sec: Video system choose. Record frame choose.

Click OK to confirm.

On Live / PlayBack , click DVR to save action pictures, *.DVR file. It needs this software to play.

Browser, Local record path could change. The path user changes is for .DVR save, *JPG file is always

C:\DVR

- Press DVR to start record .DVR file(DVR LED green on.), press again to stop.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click DDNS Host Name:

Type DVR DDNS host name: Myhostname.4irc.com

CMD Port: command port 21 or 1025 ~ 5999.

It is same as DVR network setup.

Which is same DVR MENU Æ ADVANCED SETUP Æ NETWORK SETUP Æ DVR NAME:

DNS/DDNS SETUP

TCP-IP SETUP PAGE

1. SPEED:>512K

1. D.N.S 1: 000.000.000.000

2. DVR NAME:[Myhostname

3. NET TYPE: OFF

]

2. D.N.S 2: 000.000.000.000

3. SERVER : DTDNS

4. STATIC IP SETUP

4. DOMAIN: [ 4irc.com

]

5. PPPOE ID SETUP

5. LOGIN ID:[ your DTNS long in name

]

6. DNS/DDNS SETUP

7. SERVER PORT SETUP

MAC ADDR: xx.xx.xx.xx.xx.xx

]

7. PASSWORD: [your DTNS long in password

8. CLEAR DDNS SETUP

]

DDNS host name:

Myhostname.4irc.com

Download from Www.Somanuals.com. All Manuals Search And Download.

13. Click Login, depends on limits of authority. (ID / password is same as DVR)

Factory ID is user login. Input admin if you are an administer. Must input on little character.

Factory: Password, admin : 44444, user : 11111. Password displays when log in, user just needs to input ID.

User log in, no PlayBack function authority. Total 6 people log in. Admin x 1, user x 5.

Click OK, after about 5 seconds, admin login!! Message popup. And then click Connect to start.

PASSWORD is correct.

Download from Www.Somanuals.com. All Manuals Search And Download.

14. Click Connect, after about 2 ~ 3 seconds to start connect LAN or WAN. Click Disconnect to stop.

If the NETWORK is connecting success, the blue light would keep glisten

Else, blue is always on light or not display, the connecting is failed.

Click live / PlayBack / BackPlay mode.

Live: DVR live watching.

PlayBack: Change to playback mode. After 2 ~3 seconds to change.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAY: Click RUN around 2 ~ 30 seconds to start play first record. If over 30 seconds, cannot find any file or

network disconnect, Time out message popup. Please try again play or connect again. Click STOP to end

playback.

TIME LIST: Click RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to

start play first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup.

Please try again play or connect again. Click STOP to end playback.

TIME SEARCH: Chose date and time, click RUN, around 2 ~ 30 seconds to start play first record. If over 30

seconds, cannot find any file or network disconnect, Time out message popup. Please try again play or

connect again. Click STOP to end playback.

Notice: PLAY / TIME LIST / TIME SEARCH change, needs to stop play first.

Download from Www.Somanuals.com. All Manuals Search And Download.

-Master HDD Event Lists:

-Slave HDD Event Lists:

Click RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to start play

first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup. Please

try again play or connect again. Click STOP to end playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

15. Backup Play:

- Click Open to choose file path.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click Play to start backup data play. Click Stop to end. Click Pause to temporary stop playback. Click Resume

to restart.

Choose camera, click mouse right button. Camera 1 ~ 4 switches or reset all. Click Save “CamNo xx image . /

save image all to save current image. Save path is C:\DVR.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. AVI transfer: Click Backup Play

AVI : On live or playback mode, save files to .DVR file. And then OPEN file, press play to start playback.

Press AVI button to start record AVI file. Press again to stop.

Only 2 cameras selectable. A warning message appears if user selects over 3 cameras,

Download from Www.Somanuals.com. All Manuals Search And Download.

Record Time Table: 80GB HD

Record Quality: Low. KB Range: Lowest: 13, Highest: 20. Average: 17.

REC FPS

REC Hour

REC FPS

REC Hour

REC FPS

REC Hour

120

137

1/2

274

1/3

4112

456

1/5

6853

685

1/10

13706

1370

1/15

20565

2741

1/30

41140

Record Quality: Normal. KB Range: Lowest: 14, Highest: 25. Average: 20.

REC FPS

REC Hour

REC FPS

REC Hour

REC FPS

REC Hour

120

1/2

233

1/3

3495

388

1/5

5825

582

1/10

1450

145

1/15

17479

2330

1/30

34967

Record Quality: Fine. KB Range: Lowest: 15, Highest: 28. Average: 22.

REC FPS

REC Hour

REC FPS

REC Hour

REC FPS

REC Hour

120

105

1/2

211

1/3

3177

353

1/5

5295

529

1/10

10591

1059

1/15

15890

2118

1/30

31787

Record Quality: High. KB Range: Lowest: 17, Highest: 30. Average: 24.

REC FPS

REC Hour

REC FPS

REC Hour

REC FPS

REC Hour

120

1/2

194

1/3

2912

323

1/5

4854

485

1/10

9709

970

1/15

14563

1941

1/30

29127

Record Quality: Super. KB Range: Lowest: 19, Highest: 45. Average: 32.

REC FPS

REC Hour

REC FPS

REC Hour

REC FPS

REC Hour

120

1/2

145

1/3

2184

242

1/5

3640

364

1/10

7281

728

1/15

10922

1456

1/30

21845

Actual recording time is base on live environment. This table only for reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

VGA Description (Optional)

Accessories:

1. 20 PIN Male to Female D-SUB pin cable X 1

2. VGA PCB bracket X1

3. Screws X4

1. VGA board introduction.

VGA connector

Socket

2. Resolution switcher table

Pin 4

Resolution

Pin 1

Pin 2

Pin 3

640X480 60HZ

800X600 60HZ

1024X768 60HZ

640X480 75HZ

800X600 75HZ

1024X768 75HZ

OFF

Resolution and switcher description.

Step. 1

Step. 2

Step. 3

DVR Power on. NTSC / PAL auto detects.

Pin 4 no used

Pin 1 ~ 3 switcher resolution. Do not need to power off DVR.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional

Hard Disk x 2 can be installed on DVR base. Both are 2-iron slices immobile type.

2 Iron slices are in the accessories box, please tell supplier if slices are not exist

2-iron slices immobile type:

Slices immobile type: 4 screws hole on each slice. 2 for DVR base fixed. Another 2 for hard disk fixed.

Hard disk install.: Locking hard disk screws, then locking DVR base screws to fixed on.

Download from Www.Somanuals.com. All Manuals Search And Download.

P / T / Z Dome mode.

6. ADVNACED SETUP PAGE Æ P.T.Z SETUP

ADVANCED SETUP PAGE

PTZ SETUP PAGE

CHANNEL NUMBER

1. ID

1. ALARM

SETUP

2. MOTION

3. RECORD SETUP

4. PASSWORD SETUP

5. NETWORK SETUP

2. PROTOCOL

3. BAUDRATE

4. AUTO TOUR

5. LINE SCAN

6. AUTO FOCUS

7. AUTO IRIS

6. P.T.Z

SETUP

7. HDD FORMAT

8. FACTORY DEFAULT

9. SOFTWARE UPDATE

PTZ SETUP PAGE

CHANNEL NUMBER: CH01 ~ CH4

1. ID: 01 ~ 4

2. PROTOCOL: PELCO-P / PELCO-D / LILIN / ABC / ELITAR / DENTEC-D / DENTEC-P / OFF

3. BAUDRATE: 1200 / 2400 / 4800 / 9600

4. AUTO TOUR: ON / OFF

5. LINE SCAN: ON / OFF

6. AUTO FOCUS: ON / OFF

7. AUTO IRIS:

ON / OFF

After PTZ setup done, go back to live mode. Press W.M. button to PTZ mode.

Icon displays beside date and time caption. To use direction button left/right/up/down

to move PTZ Dome. PTZ Dome can not be control on split screen.

PS. Because the P / T / Z Dome setup is independent by channel and ID, user does not worry about the

different ID / Protocol / Baud Rate would affect DVR controls P / T / Z dome error. Just make sure channel and

ID / Protocol / Baud Rate corresponding is correct.

Download from Www.Somanuals.com. All Manuals Search And Download.

Front Panel Button Comparison:

W.M.: To P / T / Z mode

PLAY / REC = IRIS off / IRIS open

= FOCUS near / FOCUS far

BACKUP / T-SRH = ZOOM IN / ZOOM OUT

MENU = P / T / Z Dome Menu

FRE. : To Preset mode. PRESET: 000 glisten on left-up corner. Moves P / T / Z dome to the position user

wants.

When “PRESET: glistening”, press number button.

EX: 1 ~ 9. 10 = 1 + 10, 11 = 1 + 1, 12 = 1 + 2, 21 = 2 + 1, 132 = 1 + 3 + 2.

ZOOM : After press ZOOM button to save the presets.

INFO : Press FRE. button into preset mode. When “PRESET: glistening”, press number button, and then

press INFO to call preset.

AUTO : Press FRE. button into preset mode. When “PRESET: glistening”, press number button, and then

press AUTO to clear preset.

Download from Www.Somanuals.com. All Manuals Search And Download.

IE Networking Software

1. This web is for preliminary IE browser.

2. User can download the network viewer from this web page or view the DVR video image in the future.

3. The AP software is already saved to DVR system IC. User needs to do is:

a.) Go to Advanced SetupÆ Network SetupÆSets LAN or WAN IP address of DVR.

b.) Open IE browser, and then into your IP on the IE address bar.

c.) If LAN or WAN connects ok, the 4 Channel Digital Video Recorder web page displays like under:

Download from Www.Somanuals.com. All Manuals Search And Download.

Lasko Fan 2515 User Manual
Lenovo Computer Monitor 4434HE1 User Manual
LG Electronics Cell Phone VX3450 User Manual
LG Electronics Computer Drive GGW H20N User Manual
Lightolier Indoor Furnishings 1001FEM Series User Manual
Lincoln Electric Welding System SVM173 A User Manual
Logitech Computer Keyboard Tab4 101 User Manual
LOREX Technology Home Security System ACC HDB120 User Manual
Maxtor Computer Drive 3000DV User Manual
Melissa Indoor Furnishings 637 005 User Manual