Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
SDI: 525i/60hz 4x3
Tel.: 800-800-6608 • 310-333-0606
Fax: 310-333-0688
Email: [email protected]
OSD
Use SELECT to enable the On Screen Display
for input and function status
V-R102DP--SD Users Guide
Blue Only
SELECT to adjust SMPTE or split field color bars.
1. Allow monitor to warm up for 5-10 minutes minimum.
2. Display SMPTE color bars on monitor. Turn on off Color with control.
3. Find the PLUGE (superblack, black, and gray bars) at the lower right
of the pattern.
Adjust BRIGHTNESS until there is no difference visible between the super-
black and black bars, but is still visible.
4. Adjust CONTRAST control to achieve a balanced gray scale across
top bars.
5. Turn up CHROMA (color level) control until the two outermost bars
(white and blue appear to match in brightness.
6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third
bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.
Product Overview
Features
1
2
3
10
Warranty
Marshall Electronics warranties to the first consumer, that this V-R102DP-SD Dual 10.4-inch LCD rack mounted monitor set will, under
normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,
labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifica-
tions in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any war-
ranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time
period described above.
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to
effective use of the monitor by our technicians.
Video - Screen Formats and Frame Rates
Electrical Specifications
Mechanical Specifications
Operational Setup
4
5
6
Connectors
7
8
9
Switch Settings, Adjustments and Indicators
Menu Functions
Due to constant effort to improve products and product features, specifications may change without notice.
Warranty
10
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Mechanical Specifications
8
Switch Settings, Adjustments and Indicators
Dimensions
19.12” w x 8.67” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R102DP-SD Weight
V-PS12-5V-1 Power Supply Weight
5.5 lbs (2.4 kg)
1 lbs (0.45kg)
Tally Lamps
Operational Setup
1. Unpack the V-R102DP-SD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have
occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call +1 310-333-0606.
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the V-R102DP-SD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R102DP-SD for all outputs
to be activated. All BNC connectors should be rated for 75Ω.
4. Plug the V-PS12-5V-1 power supply into the A.C. source
5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.
6. Turn on each of the V-R102DP-SD screens by depressing the power switch located on the front of the unit for each screen.
Tally IN
DB-15 Female
Connectors
7
Pin1-M2Yel
Pin9-
* SDI Inputs comply to SMPTE-259M, SDI-270Mbs
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
Pin2-M2Red Pin10-
Pin3-M2Grn
Pin4-
Pin11-M1Yel
Pin12-M2Red
Pin13-M3Grn
Pin14-
Pin5-Gnd
Pin6-
Pin7-
Pin15-Gnd
S-Video Out
S-Video In
4 Pin Din (Female) 4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
12 VDC from
V-PS12-5V-1 power supply
Left Pin - Pos
Right Pin- Neg
Dry Erase
Active Outputs require power to be applied
All input signals appear as output signal
Analog output signals are buffered and amplified
Image Adjustment Controls
Note: Tint only functions when NTSC
Video or S-Video are selected
Screen aspect ratio switch 4:3 or 16:9 selector and indicators
DVI-I Connector
Pin#
Pin#
Signal
Signal
1
2
3
T.M.D.S DATA 2-
T.M.D.S DATA 2+
T.M.D.S DATA 2/4
SHIELD
16
17
18
HOT PLUG DETECT
T.M.D.S DATA 0-
T.M.D.S DATA 0+
4
T.M.D.S DATA 4-
19
T.M.D.S DATA 0/5
SHIELD
5
6
7
T.M.D.S DATA 4+
DDC CLOCK
DDC DATA
20
21
22
T.M.D.S DATA 5-
T.M.D.S DATA 5+
T.M.D.S CLOCK
SHIELD
T.M.D.S CLOCK+
T.M.D.S CLOCK-
VGA/XGA Connector
PIN#
SIGNAL
RED
PIN#
9
SIGNAL
NC
NC
NC
NC
HSYNC
VSYNC
NC
1
2
3
4
5
6
7
8
8
9
10
11
ANALOG VERT. SYNC
T.M.D.S DATA 1-
T.M.D.S DATA 1+
T.M.D.S DATA 1/3
SHIELD
T.M.D.S DATA 3-
T.M.D.S DATA 3+
+5V POWER
23
24
GREEN
BLUE
NC
GND
RED SHIELD
GREEN SHIELD
BLUE SHIELD
10
11
12
13
14
15
C1
ANALOG RED
12
13
14
15
C2
C3
C4
C5
ANALOG GREEN
ANALOG BLUE
ANALOG HORZ SYNC
ANALOG GROUND
4:3 Aspect
16:9 Aspect
GND
MarshallElectronics
V-R102DP-SD Users Guide
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1 / Computer Signals Displayed via DVI and VGA connector
DVI-D
VGA
16x9
Input Signal Type
and aspect
4x3
16x9
4x3
640 x 480 60Hz
640 x 480 75Hz
640 x 480 85Hz
800 x 600 60Hz
800 x 600 75Hz
800 x 600 85Hz
1024 x 768 60Hz
1024 x 768 75Hz
1024 x 768 85Hz
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Table 3 / Video Signals Displayed via SDI
SDI
Input Signal Type and aspect
4:3
Y
16:9
Table 2 / Video Signals Displayed via DVI and YPrPb connections
(x=not available) (HDMI requires adapter to DVI)
NTSC (720x486i 60Hz)
PAL (720 x 576i 50Hz)
Y
Y
Y
Y Pr Pb
DVI
Input Signal Type
and aspect
4x3
16x9
4x3
16x9
720 x 486 60i
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
x
x
x
x
720 x 576 50i
1280 x 720 60P
1280 x 720 50P
1280 x 720 30P
1280 x720 29.97P
1280 x720 25P
1280 x 720 24P
1280 x 720 23.98P
1920 x 1080 60i
1920x1080 59.94i
1920 x 1080 50i
1920 x 1080 30P
1920x1080 29.97P
1920 x 1080 25P
1920 x 1080 24P
1920 x 1080 24Psf
Y
Y
x
Y
Y
x
x
x
x
x
x
x
x
x
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Marshall Electronics
V-R102DP-SD Users Guide
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|