Q Model
QuietQube® Ice Machines
with CVD® Technology
Models Q1400C
Installation
and
Owner/Operator
Use and Care Manual
Thank you for selecting a Manitowoc Ice Machine, the dependability leader in ice making equipment and related products.
With proper installation, care and maintenance, your new Manitowoc Ice Machine will provide you with many years of
reliable and economical performance.
Part Number 000001528
8/2006
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1
General Information
Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Read a Model Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Condensing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Cube Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD1476 Water Cooled Condensing Unit . . . . . . . . . . . . . . . . . . . . . . . . .
Bin Caster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Filter System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manitowoc Cleaner and Sanitizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aucs® Automatic Cleaning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GSI200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model/Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner Warranty Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Labor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorized Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-3
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-4
Section 2
Installation Instructions
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-1
2-1
2-2
2-2
2-2
Ice Machine Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD1476 Condenser Water Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q1400C Head Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q1400C Ice Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensing Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD1475
Air-Cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD1476
2-2
Water-Cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Storage Bin Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Head Section Clearance Requirements . . . . . . . . . . . . . . . . . . .
Stacking Two Ice Machines on a Single Storage Bin . . . . . . . . . . . . . . . . . . .
Location of CVD Condensing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensing Unit Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensing Unit Heat of Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling the Ice Storage Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air-Cooled Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-3
2-4
2-4
2-4
2-4
2-4
2-5
2-5
Part Number 000001528
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (continued)
Electrical Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse/Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum Circuit Ampacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QuietQube® Ice Machine Head Section Electrical Wiring Connections . . . .
QuietQube® Ice Machine Head Section
2-6
2-6
2-6
2-6
2-6
2-7
2-8
115/1/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QuietQube® Ice Machine Head Section
2-8
230/1/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For United Kingdom Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Electrical Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD Condensing Unit 208-230/1/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD Condensing Unit 208-230/3/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD Condensing Unit 230/1/50 (CVD1475 Only) . . . . . . . . . . . . . . . . . . . .
Ice Machine Head Section Water Supply and Drains . . . . . . . . . . . . . . . . . . .
Potable Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Potable Water Inlet Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drain Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Cooled Condenser Water Supply and Drains . . . . . . . . . . . . . . . . . . . .
Condenser Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Cooled Condenser Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensing Unit Drain Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Supply and Drain Line Sizing/Connections . . . . . . . . . . . . . . . . . . . .
Refrigeration System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Usage With Non-Manitowoc
2-8
2-8
2-9
2-9
2-9
2-9
2-10
2-10
2-10
2-10
2-10
2-10
2-10
2-10
2-11
2-12
Condensing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigeration Line Set Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Line Set Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Line Set Rise or Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. Suction Line Oil Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Starting the Ice Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AuCS® Automatic Cleaning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-12
2-13
2-13
2-13
2-13
2-14
2-20
2-21
2-21
Section 3
Ice Machine Operation
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Head Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD Condensing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Making Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Start-Up or Start-Up After Automatic Shut-Off . . . . . . . . . . . . . . . . . .
Freeze Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Harvest Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Shut-Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operational Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water float valve check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Thickness Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-1
3-2
3-3
3-3
3-3
3-3
3-3
3-4
3-4
3-4
3-4
3-4
2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (continued)
Section 4
Maintenance
Interior Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning and Sanitizing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ice Machine Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water-Cooled Condenser and Water Regulating Valve . . . . . . . . . . . . . . .
Removal from Service/Winterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVD 1476 Water Cooled Condensing Unit . . . . . . . . . . . . . . . . . . . . . . . . .
AuCS Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-8
4-8
4-8
4-8
4-9
4-10
4-10
4-10
4-10
Section 5
Before Calling For Service
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Limit Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-2
Part Number 000001528
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (continued)
4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
General Information
Model Numbers
How to Read a Model Number
This manual covers the following models:
#
CUBE SIZE CONDENSER TYPE
Ice Machine Head Section
CVD® Condensing Unit*
9 REMOTE
AIR-COOLED
2
3
4
5
DICE
DICE
AIR-COOLED
CVD1375
CVD1475
CVD1476
WATER-COOLED
QD1472C
QY1474C
HALF-DICE AIR-COOLED
HALF-DICE WATER-COOLED
For 3 phase electrical option: add the number “3” to the
end of model number (CVD14753).
Q Y 0674 C
ICE MACHINE
MODEL
ICE MACHINE
SERIES
!
Warning
PERSONAL INJURY POTENTIAL
ICE CUBE SIZE
CONDENSER TYPE
D
Y
DICE
HALF DICE
A
SELF-CONTAINEDAIR-COOLED
Do not operate equipment that has been misused,
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
W SELF-CONTAINEDWATER-COOLED
N
C
REMOTE AIR-COOLED
CVD REMOTEAIR-COOLED
SV3106
Remote Condensing Unit
!
Warning
CVD 0675 3
When installing with non-Manitowoc ice storage
systems or Manitowoc F & B style bins. Manitowoc
QuietQube® ice machines require the ice storage
bin, to incorporate an ice deflector.
CONDENSING
CONDENSING
UNIT MODEL
UNIT SERIES
Prior to using a non-Manitowoc ice storage system
with Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
3 PHASE
SV3107
Ice Cube Sizes
SV3105
Dice
Half Dice
7/8" x 7/8" x 7/8"
3/8" x 1-1/8" x 7/8"
2.22 x 2.22 x 2.22 cm 0.95 x 2.86 x 2.22 cm
Important
The ice machine sequence of operation for QuietQube®
ice machines will differ. Verify the correct sequence of
operation is followed for the model you are working on.
Part Number 000001528
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Section 1
Accessories
Contact your Manitowoc distributor for these optional accessories:
CVD1476 WATER COOLED CONDENSING UNIT
(With High Pressure Water Regulating Valve)
WATER FILTER SYSTEM
Engineered specifically for Manitowoc ice machines,
This water filter is an efficient, dependable, and
affordable method of inhibiting scale formation, filtering
sediment, and removing chlorine taste and odor.
A special order condensing unit is available that allows
condenser water inlet pressure up to 350 psig
(2413 kPA).
MANITOWOC CLEANER AND SANITIZER
BIN CASTER
Manitowoc Ice Machine Cleaner and Sanitizer are
available in convenient 16 oz. (473 ml) and 1 gal (3.78 l)
bottles. These are the only cleaner and sanitizer
approved for use with Manitowoc products.
Replaces standard legs.
ICE BAGGER
Maximize profits from bagged ice sales with this
convenient accessory. This sturdy unit rests on the bin
door frame, and adapts for left or right side filling.
Cleaner Part Number
16 oz. 94-0456-3 16 oz.
94-0580-3 1 Gallon
Sanitizer Part Number
94-0565-3
94-0581-3
ICE DEFLECTOR
1 Gallon
Q1400C ice machines mounted on an ice dispenser do
not require an ice deflector.
DISPENSER
A counter-top dispenser is ideal for cafeterias and many
types of self-service facilities. Manitowoc auto-fill, floor-
standing ice dispensers meet the strict sanitary
requirements of the food service, lodging and health
care industries.
Q1400C ice machines mounted on an ice storage bin
(Manitowoc or non-Manitowoc) require the use of an ice
deflector.
Two Q1400C ice machines can be mounted side by side
on a Manitowoc 60” F & B Style bin.
AUCS® AUTOMATIC CLEANING SYSTEM
!
Warning
This accessory reduces equipment cleaning expense.
The AuCS® accessory monitors ice making cycles and
initiates cleaning procedures automatically.
Manitowoc Q1400C ice machines require the ice
storage bin to incorporate an ice deflector.
The deflector kit is not included with the ice machine
and must be ordered separately.
GSI200
This accessory releases chlorine dioxide on a controlled
basis to inhibit the growth of bacteria and slime.
Prior to using a non-Manitowoc ice storage system
with Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
Contact your sales representative or the factory sales
department to determine the proper kit for bin
applications.
1-2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
General Information
The model and serial number are listed on the OWNER
WARRANTY REGISTRATION CARD. They are also
listed on the MODEL/SERIAL NUMBER DECAL affixed
to the ice machine head section and condensing unit.
Both model/serial numbers must be referenced to obtain
warranty or service information.
Model/Serial Number Location
Record the model and serial number of your ice machine
and bin or dispenser in the space provided below.
These numbers are required when requesting
information from your local Manitowoc distributor,
service representative, or Manitowoc Ice, Inc.
Back of Ice Machine
Condensing Unit
MODEL /
SERIAL
NUMBERS
DECAL
(ICE
MACHINE)
SV1746
MODEL /
SERIAL
NUMBERS
DECAL
MODEL / SERIAL NUMBERS DECAL
(CVD CONDENSING UNIT)
(BIN)
SV1768A
Q1400C
CVD1476 Condensing Unit
MODEL / SERIAL
NUMBERS DECAL
(RIGHT SIDE OF
ICE MACHINE
ELECTRICAL
CONTROL BOX)
MODEL / SERIAL
NUMBERS DECAL
(CVD CONDENSING
UNIT)
SV3077
SV1770A
Model/Serial Number Location
Bin or Dispenser CVD Condensing Unit
Ice Machine
AuCS Accessory
Model Number
Serial Number
Part Number 000001528
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Section 1
EXCLUSIONS
Owner Warranty Registration Card
The following items are not included in the ice machine’s
warranty coverage:
GENERAL
The packet containing this manual also includes
warranty information. Warranty coverage begins the day
the ice machine is installed.
1. Normal maintenance, adjustments and cleaning as
outlined in this manual.
2. Repairs due to unauthorized modifications to the ice
machine or use of non-standard parts without prior
written approval from Manitowoc Ice, Inc.
Important
Complete and mail the OWNER WARRANTY
REGISTRATION CARD as soon as possible to
validate the installation date.
3. Damage caused by improper installation of the ice
machine, electrical supply, water supply or drainage,
or damage caused by floods, storms, or other acts of
God.
If the OWNER WARRANTY REGISTRATION CARD is
not returned, Manitowoc will use the date of sale to the
Manitowoc Distributor as the first day of warranty
coverage for your new ice machine.
4. Premium labor rates due to holidays, overtime,
etc.; travel time; flat rate service call charges;
mileage and miscellaneous tools and material
charges not listed on the payment schedule.
Additional labor charges resulting from the
inaccessibility of equipment are also excluded.
Warranty Coverage
GENERAL
The following Warranty outline is provided for your
convenience. For a detailed explanation, read the
warranty bond shipped with each product.
5. Parts or assemblies subjected to misuse, abuse,
neglect or accidents.
6. Damage or problems caused by installation,
cleaning and/or maintenance procedures
inconsistent with the technical instructions provided
in this manual.
Contact your local Manitowoc Distributor or Manitowoc
Ice, Inc. if you need further warranty information.
Important
7. This product is intended exclusively for commercial
application. No warranty is extended for personal,
family, or household purposes.
This product is intended exclusively for commercial
application. No warranty is extended for personal,
family, or household purposes.
AUTHORIZED WARRANTY SERVICE
PARTS
To comply with the provisions of the warranty, a
refrigeration service company qualified and authorized
by a Manitowoc distributor, or a Contracted Service
Representative must perform the warranty repair.
1. Manitowoc warrants the ice machine against defects
in materials and workmanship, under normal use
and service for three (3) years from the date of
original installation.
NOTE: If the dealer you purchased the ice machine from
is not authorized to perform warranty service; contact
your Manitowoc distributor or Manitowoc Ice, Inc. for the
name of the nearest authorized service representative.
2. The evaporator and compressor are covered by an
additional two (2) year (five years total) warranty
beginning on the date of the original installation.
SERVICE CALLS
LABOR
Normal maintenance, adjustments and cleaning as
outlined in this manual are not covered by the warranty.
If you have followed the procedures listed in this manual,
and the ice machine still does not perform properly, call
your Local Distributor or the Service Department at
Manitowoc Ice, Inc.
1. Labor required to repair or replace defective
components is covered for three (3) years from the
date of original installation.
2. The evaporator is covered by an additional two (2)
year (five years total) labor warranty beginning on
the date of the original installation.
1-4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
General
These instructions are provided to assist the qualified
installer. Check your local Yellow Pages for the name of
the nearest Manitowoc distributor, or call Manitowoc Ice,
Inc. for information regarding installation and start-up
services.
Important
Failure to follow these installation guidelines may
affect warranty coverage.
Ice Machine Installation Options
CVD1476 CONDENSER WATER PRESSURE
Water pressure at the condenser cannot exceed 150
psig (1034 kPA) with the standard water-regulating
valve. Contact your distributor if your water pressure is
greater than 150 psig (1034 kPA). A special order
condensing unit is available that allows water pressure
up to 350 psig (2413 kPA).
TRIM TOP COVER
IN THIS AREA
SV1768B
Q1400C HEAD SECTION
Cut the top cover for top routing of electrical inlet, water
supply inlet or refrigeration lines.
The ice machine head can be installed with the electrical
inlet, water supply inlet and refrigeration tubing entering
from the back or top of the ice machine.
1. Prior to cutting, mount top cover onto ice machine.
The ice machine water drain must exit the back of the
ice machine.
2. Locate the area that will need to be cut and mark the
top cover.
3. Using a tin snips, cut top cover as needed:
TUBING CAN BE
ROUTED OUT
A. Do not cut out entire area! Cut up to 1/8 inch to
marked line.
BACK OF THE ICE
TUBING CAN BE
ROUTED OUT TOP
MACHINE WITH
PROVIDED 90°
ELL’S
B. Cut out only what is needed. (If routing only
refrigeration lines out the top, cut just enough to
route these lines.)
Do not cut out the entire corner area.
SV1769A
Part Number 000001528
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Ice Machine Dimensions
Q1400C ICE MACHINES
24.5”
(62.23 cm)
30”
(76.2 cm)
Important
Failure to follow these installation guidelines may
affect warranty coverage.
6.87”
(17.45 cm)
5.37”
(13.64 cm)
3.24”
(8.23 cm)
24”
(60.96 cm)
14.77”
(37.52 cm)
20.96”
(53.24 cm)
21.5”
2.02”
SV1766
(54.6 cm)
(5.13 cm)
Condensing Unit Dimensions
CVD1476
Water-Cooled
CVD1475
Air-Cooled
24.13”
(53.7 CM)
34”
(86.4 CM)
21.87”
(55.5 CM)
24.53”
(62.3 CM)
25.75”
(65.4 CM)
20.64”
(52.4 CM)
14.5”
(36.8 CM)
FRONT VIEW
14.5”
(36.8 CM)
4.26”
(10.8 CM)
9.5”
(24.1 CM)
12.6”
(32 CM)
8.54”
(21.6 CM)
8.70”
(22.1 CM)
10.75”
(27.3 CM)
SV1758
SV3076
2-2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Ice Storage Bin Dimensions
Large Capacity Ice Storage Bin Dimensions
30 INCH (76 CM)
S970 ICE STORAGE BIN
A
34” (86.4 cm)
B
25.25”
(64.1 cm)
43.6”
(110.81 cm)
6”
(15.2 cm)
SV1610
Dimension B
Bin Model Dimension A (Width)
(Height)
!
Warning
All Manitowoc ice machines require the ice storage
system (bin, dispenser, etc.) to incorporate an ice
deflector.
The Manitowoc Q1400C ice machines require
adding Manitowoc Ice Deflector Kit when installing
with non-Manitowoc ice storage systems or 60”
Manitowoc F & B style bins.
Prior to using a non-Manitowoc ice storage system
with other Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
B750
30 in. (76.2 cm.)
30 in. (76.2 cm.)
58 in. (147.3 cm.)
78 in. (198.1 cm.)
B1050
The bin drain is exactly in the center of the bin.
48 INCH (122 CM) & 60 INCH (152 CM)
A
34” (86.4 cm)
B
Caution
!
25.25”
(64.1 cm)
30” large capacity ice storage bins must be
attached to the wall with the bracket provided with
the bin.
43.6”
(110.81 cm)
6”
(15.2 cm)
Dimension A
(Width)
Dimension B
(Height)
Bin Model
B1100
B1400
48 in. (121.9 cm.)
60 in. (152.4 cm.)
55.0 in. (139.7 cm.)
55.0 in. (139.7 cm.)
The bin drain is exactly in the center of the bin.
Part Number 000001528
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Location of Ice Machine
Section 2
Location of CVD Condensing Unit
The location selected for the ice machine must meet the
following criteria. If any of these criteria are not met,
select another location.
The location selected for the CVD Condensing Unit must
meet the following criteria. If any of these criteria are not
met, select another location.
•
•
•
•
The location must be free of airborne and other
contaminants.
•
•
•
•
CVD1475 - The air temperature must be at least -
20°F (-28.9°C) but must not exceed 130°F (54.4°C).
The air temperature must be at least 35°F (1.6°C),
but must not exceed 110°F (43.4°C).
CVD1476 - The air temperature must be at least
50°F (10°C) but must not exceed 110°F (43°C).
The location must not be near heat-generating
equipment or in direct sunlight.
The location must not allow exhaust fan heat and/or
grease to enter the condenser.
The location must not obstruct airflow through or
around the ice machine. Refer to the chart below for
clearance requirements.
The location must not obstruct airflow through or
around the condensing unit. Refer to the chart below
for clearance requirements.
Ice Machine Head Section Clearance
Requirements
Condensing Unit Clearance Requirements
Top/Sides
Q1400C:
There is no minimum clearance required, although 6”
(152 mm) is recommended for efficient operation and
servicing only.,
Top/Sides 5” (127 mm) is recommended for efficient
operation and servicing. There is no minimum clearance
required.
Front/Back
Back 1” (25.4 mm) required when routing electrical inlet,
water inlet and refrigeration tubing out of the top of the
unit.
48” (122 cm)
CVD1476 ONLY
Top - 5” (127 mm) is recommended for efficient
operation and servicing only.
5” (127 mm) required when routing all connections out
the back.
Front/Back/Sides - 12” (305 mm)
Condensing Unit Heat of Rejection
Caution
!
The ice machine head section must be protected if it
will be subjected to temperatures below 32°F (0°C).
Failure caused by exposure to freezing
temperatures is not covered by the warranty. See
“Removal from Service/Winterization”.
Heat of Rejection*
Series
Condensing Unit
AirConditioning**
Peak
CVD1475
CVD1476
24,000
35,500
B.T.U./Hour
Because the heat of rejection varies during the ice making cycle,
the figure shown is an average.
Stacking Two Ice Machines on a Single
Storage Bin
Ice machines, like other refrigeration equipment, reject
heat through the condenser. It is helpful to know the
amount of heat rejected by the ice machine when sizing
air conditioning equipment where self-contained air-
cooled ice machines are installed.
Q1400C:
Q1400C ice machines cannot be stacked. However an
adapter is available that allows two Q1400C ice
machines to be placed side by side on 60” Manitowoc
F & B style bins.
This information is also necessary when evaluating the
benefits of using water-cooled or CVD® Condensing
Units to reduce air conditioning loads. The amount of
heat added to an air-conditioned environment by a
QuietQube® ice machine head section is negligible.
2-4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Leveling the Ice Storage Bin
Air-Cooled Baffle
1. Screw the leveling legs onto the bottom of the bin.
2. Screw the foot of each leg in as far as possible.
The air-cooled baffle prevents condenser air from
recirculating. To install:
1. Remove the back panel screws next to the
condenser.
Caution
!
2. Align the mounting holes in the air baffle with the
screw holes and reinstall the screws.
The legs must be screwed in tightly to prevent them
from bending.
3. Move the bin into its final position.
4. Level the bin to assure that the bin door closes and
seals properly. Use a level on top of the bin. Turn
each foot as necessary to level the bin.
NOTE: An optional caster assembly is available for use
in place of the legs. Installation instructions are supplied
with the casters.
AIR
BAFFLE
SCREWS
THREAD LEVELING
LEG INTO BASE OF
CABINET
SV1607
Air Baffle
THREAD ‘FOOT’ IN AS
FAR AS POSSIBLE
SV1606
Leveling Leg and Foot
Part Number 000001528
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
FUSE/CIRCUIT BREAKER
Electrical Service
The ice machine head section and condensing unit are
wired independently from each other.
GENERAL
Ice Machine Head Section
!
Warning
All wiring must conform to local, state and national
codes.
The ice machine head section does not require a
dedicated circuit breaker.
CVD® Condensing Unit
VOLTAGE
A separate fuse/circuit breaker must be provided for
each condensing unit. Circuit breakers must be H.A.C.R.
rated (does not apply in Canada).
For both the Ice Machine Head Section and the CVD®
Condensing Unit, the maximum allowable voltage
variation is ±10% of the rated voltage at ice machine
start-up (when the electrical load is highest).
MINIMUM CIRCUIT AMPACITY
The minimum circuit ampacity is used to help select the
wire size of the electrical supply. (Minimum circuit
ampacity is not the ice machine’s running amp load.)
The wire size (or gauge) is also dependent upon
location, materials used, length of run, etc., so it must be
determined by a qualified electrician.
!
Warning
The ice machine and condensing unit must be
grounded in accordance with national and local
electrical codes.
GROUND FAULT CIRCUIT INTERUPTER
Ground Fault Circuit Interupter (GFCI/GFI) protection is
a system that shuts down the electric circuit (opens it)
when it senses an unexpected loss of power,
presumably to ground. Manitowoc Ice, Inc. does not
recommend the use of a GFCI/GFI circuit protection with
our equipment. If code requires the use of a GFCI/GFI
then you must follow the local code. The circuit must be
dedicated, sized properly and there must be a panel
GFCI/GFI breaker. We do not recommend GFCI/GFI
outlets as they are known for more intermittent nuisance
trips than panel breakers.
2-6
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Electrical Requirements
QuietQube® Ice Machine Head Section
Voltage
Phase
Cycle
Maximum Fuse/
Circuit Breaker
Ice Machine
Q1400C
Total Amps
115/1/60
208-230/1/60
230/1/50
15 amp
15 amp
15 amp
1.1
0.6
0.6
Important
The QuietQube® Ice Machine Head Section and
CVD Condensing Unit are wired independently from
each other.
CVD® Condensing Unit
Condensing Unit
Voltage Phase
Cycle
Maximum Fuse/Circuit
Breaker
Minimum Circuit Amps
208-230/1/60
208-230/3/60
230/1/50
35
25
35
30
20
19.6
14.1
19.8
15.3
10.8
CVD1475
CVD1476
208-230/1/60
208-230/3/60
Part Number 000001528
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
QuietQube® Ice Machine Head Section Electrical Wiring Connections
QUIETQUBE® ICE MACHINE HEAD SECTION
230/1/50
!
Warning
These diagrams are not intended to show proper
wire routing, wire sizing, disconnects, etc., only the
correct wire connections.
All electrical work, including wire routing and
grounding, must conform to local, state and national
electrical codes.
L
L
1
1
Though wire nuts are shown in the drawings, the ice
machine field wiring connections may use either
wire nuts or screw terminals.
N
N
QUIETQUBE® ICE MACHINE HEAD SECTION
115/1/60
GROUND
GROUND
L
L
1
1
ICE MACHINE
CONNECTIONS
TO SEPARATE
FUSE/BREAKER.
DISCONNECT ALL
POLES.
N=115V
OR
L2=208-230V
SV1191
GROUND
GROUND
ICE MACHINE
CONNECTIONS
SV1258
For United Kingdom Only
As the colours of the wires in the mains lead of the appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
•
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with
the letter E or by the earth ground symbol or coloured green or green and yellow.
•
•
The wire coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
2-8
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
CVD CONDENSING UNIT
208-230/3/60
Remote Electrical Wiring Connections
!
Warning
These diagrams are not intended to show proper
wire routing, wire sizing, disconnects, etc., only the
correct wire connections.
L
L
1
2
L
1
All electrical work, including wire routing and
grounding, must conform to local, state and national
electrical codes.
L
L
2
3
Though wire nuts are shown in the drawings, the ice
machine field wiring connections may use either
wire nuts or screw terminals.
L
3
GROUND
GROUND
CVD CONDENSING UNIT
208-230/1/60
TO SEPARATE
FUSE/BREAKER
CONDENSING
UNIT
CONNECTIONS
SV1190
L
L
1
1
CVD CONDENSING UNIT
230/1/50 (CVD1475 ONLY)
L2
L
1
L
1
GROUND
GROUND
N
N
TO SEPARATE
FUSE/BREAKER
CONDENSING UNIT
CONNECTIONS
SV1258
GROUND
GROUND
TO SEPARATE
FUSE/BREAKER.
DISCONNECT ALL
POLES.
CONDENSING UNIT
CONNECTIONS
SV1191
Part Number 000001528
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Ice Machine Head Section Water Supply
and Drains
Water Cooled Condenser Water Supply and
Drains
POTABLE WATER SUPPLY
CONDENSER WATER SUPPLY
Local water conditions may require treatment of the
water to inhibit scale formation, filter sediment, and
remove chlorine odor and taste.
Local water conditions may require treatment of the
water to inhibit scale formation, filter sediment, and
remove chlorine odor and taste.
WATER COOLED CONDENSER LINES
Important
Follow these guidelines to install water lines:
If you are installing a Manitowoc water filter system,
refer to the Installation Instructions supplied with the
filter system for ice making water inlet connections.
•
•
Contact your distributor if your water pressure is
greater than 150 psig (1034 kPA). A special order
condensing unit is available that allows water
pressure up to 350 psig (2413 kPA).
POTABLE WATER INLET LINES
Follow these guidelines to install water inlet lines:
Install a shutoff valve (inlet and outlet on cooling
tower or closed loop circuits) to allow isolation of the
water system.
•
Do not connect the ice machine to a hot water
supply. Be sure all hot water restrictors installed for
other equipment are working. (Check valves on sink
faucets, dishwashers, etc.)
•
•
•
•
Water entering the condenser must not exceed 90°F
(32.2°C).
•
If water pressure exceeds the maximum
recommended pressure, obtain a water pressure
regulator from your Manitowoc distributor.
Float Valve - 80 psig (551.5 kPA)
Water flow through the condenser must not exceed 5
gallons (19 liters) per minute.
Allow for a pressure drop of 8 psig (55 kPA) between
the condenser water inlet and outlet.
•
•
Install a water shut-off valve for ice making potable
water.
Water exiting the condenser must no exceed 110°F
(43.3°C).
Insulate water inlet lines to prevent condensation.
CONDENSING UNIT DRAIN CONNECTIONS
DRAIN CONNECTIONS
The condensing unit drain is provided to remove any
condensate produced by the suction accumulator.
Condensate amounts will vary depending on
temperature and humidity.
Follow these guidelines when installing drain lines to
prevent drain water from flowing back into the ice
machine and storage bin:
•
•
•
•
Drain lines must have a 1.5 inch drop per 5 feet of
run (2.5 cm per meter), and must not create traps.
•
•
•
The condensing unit must be level front to back and
side to side to allow the condensate to drain.
The floor drain must be large enough to
accommodate drainage from all drains.
Drain lines must have a 1.5-inch drop per 5 feet of
run (2.5 cm per meter), and must not create traps.
Run separate bin and ice machine drain lines.
Insulate them to prevent condensation.
Drain termination must meet applicable costs.
Vent the bin and ice machine drain to the
atmosphere. The ice machine drain requires an 18”
vent.
2-10
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
WATER SUPPLY AND DRAIN LINE SIZING/CONNECTIONS
Caution
!
Plumbing must conform to state and local codes.
Tubing Size Up to Ice
Machine Fitting
Location
Water Temperature
Water Pressure
Ice Machine Fitting
33°F (0.6°C) Min.
90°F (32.2°C) Max.
20 psi (137.9 kPA) Min.
80 psi (551.5 kPA) Max.
20 psi (137.9 kPA) Min.
80 psi (551.5 kPA) Max.
CVD1476
3/8” Female Pipe
Thread
3/8” (9.5 mm) min. inside
diameter
Ice Making
Water Inlet
33°F (0.6°C) Min.
90°F (32.2°C) Max.
Water Cooled
Condenser
1/2” Female Pipe
Thread
1/2” (12.7 mm) min. inside
diameter
20 psi (137.9 kPA) Min.
350 psi (2413 kPA) Max.
---
Ice Making
Water Drain
---
---
---
1/2” Female Pipe
Thread
1/2” (12.7 mm) min. inside
diameter
---
---
3/4” Female Pipe
Thread
3/4” (19.1 mm) min. inside
diameter
Bin Drain
Large Capacity
Bin Drain
1” (25.4 mm) min. inside
1” Female Pipe Thread
diameter
ICE MAKING WATER
INLET FITTING
3/8” F.P.T. (0.95 cm)
18.00” VENT
(45.70 cm)
ICE MAKING WATER
DRAIN FITTING
1/2” F.P.T. (1.27 cm)
VENT
ICE MAKING WATER
DRAIN TUBING
1/2” MIN. I.D. (1.27 cm)
BIN DRAIN FITTING
3/4” F.P.T. (1.91 cm)
BIN DRAIN TUBING
3/4”MIN. I.D. (1.91 cm)
DO NOT
TRAP
MUST HAVE
AIR-GAP
INCORRECT
AIR GAP
OPEN, TRAPPED OR
VENTED DRAIN
Typical Water Supply and Drain Installation
Part Number 000001528
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Factory Equipment Refrigeration Amounts
Refrigeration System Installation
ICE MACHINE HEAD SECTION
Remote Single
QuietQube®
Circuit
Line Set*
Each ice machine head section ships from the factory
with a R-404A refrigerant charge appropriate for the
entire system operation. The serial tag on the ice
machine indicates the refrigerant charge. The refrigerant
charge is sufficient to operate the ice machine in
ambient temperatures between -20°F (-28.9°C) and
130°F (54.4°C)*. With line set lengths of up to 100 feet
(30.5 m).
Ice Machine
Condenser
RC-20
RC-30
RC-50
CVD1475
Q1400C
CVD1476
Insulation
Thickness
Line Set
Suction Line Liquid Line
*CVD1476 - 50°F to 110°F (10°C to 43°C)
1/2”(13mm)
Suction Line
3/4 inch
1/2 inch
RC 20/30/50
(19.1 mm)
(12.7 mm)
1/4” (7mm)
Liquid Line
!
Warning
The ice machine head section contains the refrigerant
charge. Installation and brazing of the line sets must be
performed by a properly trained and EPA certified
refrigeration technician aware of the dangers of dealing
with refrigerant charged equipment.
USAGE WITH NON-MANITOWOC
CONDENSING UNITS
Manitowoc CVD® Condensing Units are specifically
designed for usage with a QuietQube® Ice Machine
Head Section. Standard condensing units and Non-
Manitowoc condensing units will not operate a
QuietQube® Ice Machine Head Section.
Caution
!
Never add more than nameplate charge to the
refrigeration system for any application.
CVD® CONDENSING UNIT
Caution
!
Each condensing unit ships from the factory pressurized
with 50/50 nitrogen helium mixture that must be
removed during the installation process (approximately
20 psig).
The 60-month compressor warranty (including the
36-month labor replacement warranty) will not apply if
the Manitowoc Ice Machine and Manitowoc CVD
Condensing Unit are not installed according to
specifications. This warranty also will not apply if the
refrigeration system is modified with a condenser,
heat reclaim device, or other parts or assemblies not
manufactured by Manitowoc Ice, Inc.
REFRIGERATION LINE SETS/TRAP KIT
Refrigeration Rated Tubing and Trap Kits are shipped
capped with atmospheric pressure.
!
Warning
Installation of a QuietQube® Condensing Unit may require
the use of special equipment for placement. Trained and
qualified personnel are required for proper rigging and
lifting.
2-12
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
A. LINE SET LENGTH
Refrigeration Line Set Installation
100 feet (30.5 m) Length: The maximum measured
length the line set can be.
GENERAL
Refrigeration line set installations consist of vertical and
horizontal line set distances between the ice machine
and the condensing unit. The following guidelines,
drawings and calculation methods must be followed to
assure proper oil return and CVD® condensing unit/ice
machine operation.
The receiver is designed to hold a charge sufficient to
operate the ice machine in ambient temperatures
between -20°F (-28.9°C) and 130°F (54.4°C), with line
set lengths of up to 100 feet (30.5 m). CVD1476 - 50°F
to 110°F (10°C to 43°C)
The refrigeration line set installer must be USA
Government-Environmental Protection Agency (EPA)
certified in proper refrigerant handling and servicing
procedures.
Important
QuietQube® ice machines will not function with line
sets greater than 100 feet (30.5 m). Do not attempt to
go beyond this distance and add refrigerant charge to
compensate!
!
Warning
The ice machine head section contains refrigerant
charge. The ice machine head section contains three
(3) refrigeration valves that must remain closed until
proper installation of the line sets is completed.
B. LINE SET RISE OR DROP
!
Warning
35’ (10.7 M)
MAX.
DISTANCE
Disconnect electrical power to the ice machine head
section and CVD® condensing unit before
proceeding.
Step 1 Verify Ice Machine and CVD® Condensing
Unit Locations Are Within Guidelines.
Prior to installation of the ice machine head section and
CVD® condensing unit be sure that the distance
between then is within the line set routing guidelines
outlined in this manual.
SV1751
35 feet (10.7 m) Rise: The maximum distance the
CVD® condensing unit can be above the ice machine.
Roof/Wall Penetration
If required, cut a 3-inch (76.2 mm) circular hole in the
wall or roof for routing of refrigeration tubing. A qualified
person must perform all roof penetrations.
Step 2 Route Refrigeration Tubing
Properly route refrigeration tubing between the ice
machine head section and the CVD® condensing unit.
15’ (4.5 M)
MAX.
DISTANCE
SV1750
15 feet (4.5 m) Drop: The maximum distance the CVD®
condensing unit can be below the ice machine.
Part Number 000001528
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
C. SUCTION LINE OIL TRAPS
Service Loop
A service loop in the line set permits easy access to the
ice machine for cleaning and service.
Caution
!
Do not form unwanted traps in refrigeration lines.
Never coil excess refrigeration tubing.
•
The supplied service loop is an installation
requirement. Excess tubing length must be
sufficient to allow 180° rotation of the ice
machine.
0 to 20 feet (0 to 6.1 m) Rise: The ice machine head
section has one oil trap built in which allows for a
maximum condenser rise of 20 feet (6.1 m) without
additional traps in the suction line.
•
•
A service loop is not considered an oil trap.
The service loop is not included when calculating
length, rise or drop of the tubing run.
21 to 35 feet (6.4 to 10.7 m) Rise: The suction line
requires an additional Oil Trap (“S” type) to be installed.
Install the trap as close as possible to midpoint between
the ice machine head section and CVD condensing unit.
S-Trap Kits are available from Manitowoc (refer to chart).
•
Do not use hard rigid copper for the service loop.
Caution
!
If a line set has a rise followed by a drop, another rise
cannot be made. Likewise, if a line set has a drop
followed by a rise, another drop cannot be made.
Step 3 Lengthening or Reducing Line Set Lengths
21’ OR MORE
RISE
ADDITIONAL
TRAP KIT
REQUIRED
Caution
!
Do not form unwanted traps in refrigeration lines.
Never coil excess refrigeration tubing.
When the line set required shortening or lengthening, do
so before connecting the line set to the ice machine
head section or the CVD condensing unit.
SV1751
SV1760
Manitowoc S-Trap Kit
Model
S-Trap Kit
Tubing Size
Number
3/4 inch
Q1400C
K00166
(19.1 mm)
2-14
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Step 4 Connecting the line set.
Connect The Line Set To The CVD Condensing Unit
To prevent oxidation of the copper, purge line set and
condensing unit with dry nitrogen while brazing.
!
Warning
The condensing unit ships from the factory
pressurized with a 50/50 mixture of nitrogen/helium.
Bleed off pressure from both suction and liquid line
access ports prior to cutting into refrigeration lines.
Connect The Line Set To The Ice Machine Head
Section
!
Warning
The ice machine head section contains refrigerant
charge. The ice machine head section contains three
(3) refrigeration valves that must remain closed until
proper installation of the line sets is completed.
The compressor oil rapidly absorbs moisture. Be
prepared to complete line set installation and start your
evacuation process in order to minimize the time the
compressor is exposed to the atmosphere. (Maximum
amount of time the system can be exposed to the
atmosphere is 15 minutes).
The line set can be routed for entry through the top or
rear of the ice machine head section.
CVD1475
•
•
Top routing requires the cover to be trimmed.
The line set can be routed for entry through the rear or
left side of the condensing unit.
Rear routing requires the use of the supplies 90°
elbows.
•
•
Remove knockout for preferred location.
The line set shut off valves at the back of the ice
machine must remain closed and be protected from heat
during the brazing process. Wrap the valves in a wet rag
or other type of heat sink prior to brazing. Cool braze
joint with water immediately after brazing to prevent heat
migration to the valve.
Insert supplied plastic bushings in knockout holes to
prevent tubing from contacting sheet metal.
•
Use the supplied 90° elbows to route tubing.
CVD1475 and CVD1476
•
Cut the tubing ends of the suction and liquid lines
and braze the line sets to the condensing unit.
SUCTION
FILTER
VALVES MUST REMAIN
CLOSED AND BE
PROTECTED FROM
HEAT WHEN BRAZING
(WRAP WITH WET RAG)
SUCTION
LINE
MINIMIZE THE TIME THE REFRIGERATION
SYSTEM IS EXPOSED TO THE ATMOSPHERE
(15 MINUTES MAXIMUM)
SV2085
SV1757
!
Warning
The condensing unit ships from the factory
pressurized with a 50/50 mixture of nitrogen/helium.
Bleed off pressure from both suction and liquid line
access ports prior to cutting into refrigeration lines.
LIQUID
LINE
SUCTION
LINE
SV3077
Part Number 000001528
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Step 5 Pressure Test and Evacuate The Line Set
and CVD Condensing Unit
If required, the line set and condensing unit can be
evacuated from the schrader valves located in the CVD
condensing unit. Schrader valve core removal tools (that
allow for putting the cores back in without removing
vacuum pump hoses) must be used if evacuating from
the condensing unit side.
Schrader valve core removal tools that allow for removal
and installation of the valve cores without removing
manifold gauge set hoses are recommended to
decrease the evacuation time.
Pressure test the condensing unit and line set with 150
psig of dry nitrogen. Add nitrogen at the condensing unit
Schrader valves. Complete the pressure test, verify no
leaks are present and remove the nitrogen from the
system before connecting a vacuum pump. Connect the
vacuum pump to both the Schrader valves and evacuate
to 500 microns minimum.
Leave the line set shut off valves closed (front seated).
Pressure test the line sets and CVD condensing unit
with 150 psig of dry nitrogen. Add nitrogen at the line set
shut off valves located at the back of the ice machine.
Complete the pressure test, verify no leaks are present
and remove the nitrogen from the system before
connecting the vacuum pump. Connect a vacuum pump
to both of the line set shut off valves located at the back
of the ice machine head section. Evacuate to 500
microns minimum. To completely evacuate the CVD
condensing unit, continue the evacuation for 30 minutes
after reaching the 500 micron point.
Disconnect the vacuum pump from the condensing unit
access ports prior to proceeding. Open refrigeration
system shut off valves.
The suction line, liquid line and receiver service valves
are closed during shipment and installation.
CVD1475 CONDENSING UNIT SCHRADER
VALVES
CONNECT
VACUUM PUMP TO
LINE SET SHUT
OFF VALVES
SV1757
SV1769b
CVD1476
CONDENSING UNIT
SCHRADER VALVES
SV3081
2-16
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Important
Step 6 Open The Valves Prior To Starting The Ice
Machine.
The suction line, liquid line and receiver service valves
are closed during shipment and installation. Open the
valves prior to starting the ice machine.
All refrigeration valve caps must be reinstalled to
prevent future refrigeration leaks.
A. Slowly backseat (open-turn counterclockwise)
the suction line shut off valve.
Verify O-ring in schrader valve caps are intact and
reinstall on shut off valves to prevent refrigerant leakage.
Replace shut off valve access caps and torque to the
following specifications.
B. Slowly backseat (open-turn counterclockwise)
the liquid line shut off valve.
Torque Value’s
C. Slowly backseat (open-turn counterclockwise)
the receiver service valve.
Stem
18-20 ft. lbs.
12-15 ft. lbs.
1.5-3 in. lbs.
Caps
NOTE: You will not hear refrigerant flow when the valves
are opened. Refrigerant will not flow until the toggle
switch is placed in the ice position and the liquid line
solenoid valve opens.
Schrader Core
Replace cap on receiver service valve and tighten.
TURN
COUNTERCLOCKWISE
USE ALLEN WRENCH TO OPEN
(TURN COUNTERCLOCKWISE)
LIQUID AND SUCTION LINE SHUT
OFF VALVES
RECEIVER SERVICE VALVE CAP
(TURN COUNTERCLOCKWISE
SV1769C
TO REMOVE)
SV1756
OPEN SUCTION AND LIQUID LINE SHUT OFF VALVES
Open Receiver Service Valve
There is a liquid line solenoid valve at the outlet of the
receiver; refrigerant will not flow to the condensing unit
until the ice machine head section is started. Connect
power to both the ice machine head section and the
CVD condensing unit. Place the ICE/OFF/CLEAN toggle
switch into the ICE position, this will allow refrigerant to
enter the line set and condensing unit.
Caution
!
After opening suction, discharge and receiver service
valves, refrigerant pressure will not be detected until
the toggle switch is placed in the ice position and the
harvest solenoid valve energizes.
Part Number 000001528
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Step 7 Leak Check The Refrigeration System
Leak check the new line set connections at the ice
machine head section, condensing unit and S trap as
well as all factory joints throughout the entire system.
Disconnect power to the CVD condensing unit. Place the
ICE/OFF/CLEAN toggle switch into the ICE position.
This allows the low side and high side pressures to
equalize. Place the ICE/OFF/CLEAN toggle switch in the
OFF position. Connect power to the CVD condensing
unit and allow system to pump down.
Step 8 Insulation Requirements
To prevent condensation the entire suction line including
the shut-off valve must be insulated. All insulation must
be airtight and sealed at both ends. Insulate shut-off
valves with the supplied preformed insulation.
The following insulation requirements prevent
condensation at 90°F (32.2°C) ambient 90% Relative
Humidity. If higher humidity is expected, increase
insulation thickness.
The entire suction line set, including the suction service
valve located on the back of the ice machine requires:
Suction Line
Liquid Line
Min. Insulation
Thickness
1/2”(13mm)
Suction Line
3/4 inch
1/2 inch
(19.1 mm)
(12.7 mm)
1/4” (7mm)
Liquid Line
Important
To prevent condensation the entire suction line
including the shut off valve must be insulated. All
insulation must be airtight and sealed at both ends.
The minimum requirements are for conditions at or
below 90% humidity and 90°F (32.2°C) ambient.
When higher humidity will be experienced, insulation
wall thickness will need to be increased.
2-18
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
CVD CONDENSING
UNIT
ELECTRICAL
DISCONNECT
SUCTION
LINE
LIQUID
LINE
SUCTION
REFRIGERANT
SHUT-OFF VALVE
LIQUID
REFRIGERANT
SHUT-OFF VALVE
ICE MACHINE
HEAD SECTION
ELECTRICAL
SUPPLY
ELECTRICAL
DISCONNECT
BIN
SV1768c
Typical QuietQube System Installation
Part Number 000001528
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Installation Checklist
Has the ice machine receiver service valve been
opened?
Is the Ice Machine level?
Has all of the internal packing been removed?
Does the condenser fan motor(s) operate
properly after start-up?
Have all of the electrical and water connections
been made?
Have all the refrigeration fittings and joints been
leak checked?
Has the supply voltage been tested and checked
against the rating on the nameplate?
Is the line set routed properly?
Is there proper clearance around the ice machine
for air circulation?
Is a refrigeration oil trap (S-trap) installed if the
condenser is installed 21 to 35 feet (6.1 to 10.7m)
above the ice machine head?
Has the ice machine been installed where
ambient temperatures will remain in the range of
35° - 110°F (1.7° - 43.3°C)?
Has the CVD® condensing unit been installed to
prevent any roofing damage?
Has the ice machine been installed where the
incoming water temperature will remain in the
range of 33° - 90°F (0.6° - 32.2°C)?
Have the refrigeration lines been insulated and
secured properly to prevent vibration?
Has the remote condensing unit been located
where ambient temperatures will remain in the
range of -20° to 130°F (-28.9° to 54.4°C)?
Are the ice machine and bin drains separately
vented?
CVD1476 - Is the condensing unit level?
Is the float valve in the OPEN position?
Is the toggle switch set to ice?
Are all electrical leads free from contact with
refrigeration lines and moving equipment?
Is the ice thickness control set correctly?
Has the owner/operator been instructed regarding
maintenance and the use of Manitowoc Cleaner
and Sanitizer?
CVD1476 Only - Is the drain installed on the
condensing unit?
Has the warranty registration card been sent to
the factory?
Has the ice machine and bin been sanitized?
2-20
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
AuCS® Automatic Cleaning System
Before Starting the Ice Machine
All Manitowoc ice machines are factory-operated and
adjusted before shipment. Normally, new installations do
not require any adjustment.
This optional accessory monitors ice making cycles and
initiates cleaning procedures automatically. The AuCS®
accessory can be set to automatically clean or sanitize
the ice machine every 2, 4 or 12 weeks. Refer to the
AuCS® Installation and Owner/Operator Use and Care
Guide for details.
To ensure proper operation, follow the Operational
Checks in Section 3 of this manual. Starting the ice
machine and completing the Operational Checks are the
responsibilities of the owner/operator.
Adjustments and maintenance procedures outlined in
this manual are not covered by the warranty.
!
Warning
Do not operate equipment that has been misused.
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
SV1601
Part Number 000001528
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
THIS PAGE INTENTIONALLY LEFT BLANK
2-22
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Ice Machine Operation
Component Identification
ICE MACHINE HEAD SECTION
Q1400C
EVAPORATOR
DISTRIBUTION
TUBE
WATER
PUMP
SUCTION LINE
SHUT-OFF
VALVE
LIQUID LINE
SHUT-OFF
VALVE
HARVEST
VALVE
WATER
DUMP VALVE
RECEIVER
SERVICE
VALVE
SV1780
SV1770RH
LIQUID LINE
SOLENOID
VALVE
WATER
CURTAIN
WATER
TROUGH
RECEIVER
ICE
THICKNESS
PROBE
ICE/OFF/CLEAN
TOGGLE
WITCH
FLOAT VALVE
(WATER INLET)
HARVEST
VALVE
SV1770LH
Part Number 000001528
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice Machine Operation
Section 3
CVD CONDENSING UNIT
CVD1475
CVD1476
LIQUID LINE
AND
SUCTION LINE
CONNECTION
POINTS
ACCESS
VALVES
CONDENSER
FAN MOTOR
HEAD PRESSURE
CONTROL VALVE
AIR
CONDENSER
ELECTRICAL
COMPARTMENT
LOW
ELECTRICAL
COMPARTMENT
PRESSURE
CONTROL
VALVE
HEAD
PRESSURE
CONTROL
VALVE
WATER
REGULATING
VALVE
LIQUID LINE AND
SUCTION LINE
CONNECTION
POINTS
WATER
COOLED
CONDENSER
SUCTION
ACCUMULATOR
COMPRESSOR
SUCTION
ACCUMULATOR
COMPRESSOR
PT1382
SV2085
3-2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Ice Machine Operation
Ice Making Sequence of Operation
INITIAL START-UP OR START-UP AFTER
AUTOMATIC SHUT-OFF
HARVEST SEQUENCE
4. Water Purge
1. Water Purge
The water pump continues to run, and the water dump
valve energizes for 45 seconds to purge the water in the
sump trough. After the 45 second water purge, the water
pump and dump valve de-energizes.
Before the refrigeration system starts, the water pump
and water dump solenoid are energized for 45 seconds,
to completely purge the ice machine of old water. This
feature ensures that the ice making cycle starts with
fresh water.
Both harvest solenoid valves also open at the beginning
of the water purge to divert refrigerant gas into the
evaporator.
FREEZE SEQUENCE
2. Prechill
5. Harvest
Ice Machine Head Section: The liquid line solenoid
valve energize after the 45 second water purge and
remains on throughout the entire ice making Freeze and
Harvest Sequences. The liquid line solenoid is
energized for 30 seconds prior to water flow. This allows
the refrigeration system to start-up and prechills the
evaporator.
The harvest solenoid valves remain open and the
refrigerant gas warms each evaporator causing the
cubes to slide as a sheet, off the evaporator and into the
storage bin. The ice may fall first from either the right or
the left evaporator, or both at the same time. The sliding
sheet of cubes swings the water curtain out, opening the
corresponding bin switch.
CVD Condensing Unit: When the refrigerant pressure
is high enough to close the low pressure switch, the
contactor coil is energized and the compressor and
condenser fan motor (CVD1475 only) start. They are
supplied with power throughout the entire Freeze and
Harvest Sequences. The fan motor (CVD1475 only) is
wired through a fan cycle pressure control, therefore it
may cycle on and off.
The momentary opening and closing of the bin switch
de-energizes relay#2 (right) or #3 (left). Opening relay
#2 or #3 de-energizes the corresponding harvest
solenoid valve for the remainder of the Harvest
Sequence. The momentary opening and closing of both
bin switches terminates the Harvest Sequence and
returns the ice machine to the Freeze Sequence (steps
2-3).
3. Freeze
AUTOMATIC SHUT-OFF
6. Automatic Shut-Off
The water pump restarts after the 30 second Prechill. An
even flow of water is directed across the evaporator and
into each cube cell, where it freezes.
Ice Machine Head Section: When the storage bin is full
at the end of a harvest sequence, the sheet of cubes
fails to clear either one or both water curtains. After one
or both water curtains are held open for 7 seconds, all
five relays are held open the ice machine shuts off.
When sufficient ice has formed, the water flow (not the
ice) contacts the ice thickness probe. After
approximately 7 seconds of continual water contact, the
Harvest Sequence is initiated. The ice machine cannot
initiate a Harvest Sequence until a 6-minute freeze lock
has been surpassed.
CVD Condensing Unit: When the refrigerant pressure
is low enough to open the low-pressure switch, the
contactor coil is de-energized and the compressor and
condenser fan motor (CVD1475 Only) stop.
The ice machine remains off until enough ice has been
removed from the storage bin to allow the ice to fall clear
of the water curtain(s). As the water curtain(s) swing
back to the operating position, the bin switch re-closes
and the ice machine restarts (steps 1 - 2).Both curtains
must be closed to start an ice making sequence.
Part Number 000001528
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice Machine Operation
Section 3
WATER FLOAT VALVE CHECK
Operational Checks
Before water will flow into the water trough the float
valve shut-off must be in the OPEN position.
GENERAL
Manitowoc ice machines are factory-operated and
adjusted before shipment. Normally, a newly installed ice
machine does not require any adjustment.
To ensure proper operation, always follow the
Operational Checks:
PRESS TO OPEN
PRESS TO CLOSE
•
•
•
when starting the ice machine for the first time
after a prolonged out of service period
after cleaning and sanitizing
NOTE: Routine adjustments and maintenance
procedures outlined in this manual are not covered by
the warranty.
ICE THICKNESS CHECK
After a harvest cycle, inspect the ice cubes in the ice
storage bin. The ice thickness probe is factory-set to
maintain the ice bridge thickness at 1/8" (3.2 mm).
WATER LEVEL
1. Check the water level while the ice machine is in the
freeze mode and the water pump is running. The
correct water level is 1/8” - 1/2” (3-12.5 mm)
NOTE: Make sure the water curtain is in place when
performing this check. It prevents water from splashing
out of the water trough.
2. The float valve is factory set for the proper water
level. If adjustments are necessary:
1. Inspect the bridge connecting the cubes. It should
be about 1/8" (3.2 mm) thick.
A. Loosen the two screws on the float valve
bracket.
2. If adjustment is necessary, turn the ice thickness
probe adjustment screw clockwise to increase
bridge thickness, counterclockwise to decrease
bridge thickness.
B. Raise or lower the float valve assembly as
necessary then tighten the screws.
C. If further adjustment is required, carefully bend
the float arm to achieve the correct water level.
NOTE: Turning the adjustment 1/3 of a turn will change
the ice thickness about 1/16" (1.5 mm).
WATER PUMP
IMPELLER
HOUSING
ADJUSTING SCREW
1/8” ICE BRIDGE THICKNESS
SV1616
SV1208
Ice Thickness Check
3. Make sure the ice thickness probe wire and the
bracket do not restrict movement of the probe.
3-4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
Section 4
Maintenance
Interior Cleaning and Sanitizing
GENERAL
Step 3 Remove all ice from the bin.
Clean and sanitize the ice machine every six months for
efficient operation. If the ice machine requires more
frequent cleaning and sanitizing, consult a qualified
service company to test the water quality and
recommend appropriate water treatment. The ice
machine must be taken apart for cleaning and sanitizing.
Step 4 Place the toggle switch in the CLEAN position.
The water will flow through the water dump valve and
down the drain. Wait until the water trough refills and
water flows over the evaporator, then add the proper
amount of ice machine cleaner.
Model
Amount of Cleaner
Caution
!
Q1400C
5 ounces (150 ml)
Use only Manitowoc approved Ice Machine Cleaner
and Sanitizer for this application (Manitowoc
Cleaner part number 94-0546-3 and Manitowoc
Sanitizer part number 94-0565-3). It is a violation of
Federal law to use these solutions in a manner
inconsistent with their labeling. Read and
understand all labels printed on bottles before use.
Step 5 Wait until the clean cycle is complete
(approximately 30 minutes) then place the toggle switch
in the OFF position and disconnect power to the ice
machine (and dispenser when used).
!
Warning
Disconnect the electric power to the ice machine at
the electric service switch box.
CLEANING PROCEDURE
Caution
!
Do not mix Cleaner and Sanitizer solutions together.
It is a violation of Federal law to use these solutions
in a manner inconsistent with their labeling.
!
Warning
Wear rubber gloves and safety goggles (and/or face
shield) when handling ice machine Cleaner or
Sanitizer.
Ice machine cleaner is used to remove lime scale and
mineral deposits. Ice machine sanitizer disinfects and
removes algae and slime.
Step 1 Set the toggle switch to the OFF position after
ice falls from the evaporator at the end of a Harvest
cycle. Or, set the switch to the OFF position and allow
the ice to melt off the evaporator.
Caution
!
Never use anything to force ice from the evaporator.
Damage may result.
Step 2 Remove front cover.
Part Number 000001528
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
Step 6 Remove parts for cleaning.
B. Remove the water curtain
•
•
Gently flex the curtain in the center and remove it
from the right side.
!
Warning
Slide the left pin out.
Disconnect the electric power to the ice machine at
the electric service switch box..
A. Remove the splash shield
•
•
Pull forward on left and right nylatch connectors until
disengaged from ice machine (connectors remain
attached to splash shield).
Remove panel from front of ice machine by lifting
forward and up.
Water Curtain Removal
C. Remove the ice thickness probe
•
Compress the hinge pin on the top of the ice
thickness probe.
COMPRESS
HINGE PIN TO
REMOVE
NYLATCH CONNECTORS
PULL FORWARD TO
SV1771A
DISENGAGE
Important
Splash Shield must be reinstalled to prevent water
leakage.
SV3135
Ice Thickness Probe Removal
•
Pivot the ice thickness probe to disengage one pin
then the other. The ice thickness probe can be
cleaned at this point without complete removal. If
complete removal is desired, disconnect the ice
thickness control wiring from the control board.
4-2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
D. Remove the water distribution tube
E. Remove the float valve
•
Remove the clamp from the vinyl water hose on the
right side of the distribution tube.
•
•
Turn off the water supply to the ice machine at the
water service valve.
Turn the splash shield counterclockwise one or two
turns.
2
3
1. LIFT UP
WATER INLET
2. SLIDE BACK
1
COMPRESSION
TUBE
3. SLIDE TO RIGHT
FITTING
DISTRIBUTION
TUBE
ON/OFF SLIDE
SWITCH
THUMBSCREW
FILTER
SCREEN
AND CAP
LOCATING
PIN
SPLASH
SHIELD
SV1217
THUMBSCREW
Float Valve Removal
SV1620
•
•
•
Pull the float valve forward and off the mounting
bracket.
Water Distribution Tube Removal
•
•
Loosen the two thumbscrews which secure the
distribution tube.
SU1024YC - Loosen the three thumbscrews, which
secure the distribution tube.
Disconnect the water inlet tube from the float valve at
the compression fitting.
Remove the filter screen and cap for cleaning.
Lift the right side of the distribution tube up, and then
rotate it backward and to the right until the left side of
the distribution tube disengages the thumbscrew.
Caution
!
Do not force this removal. Be sure the locating tab is
clear before rotating the distribution tube back.
•
Pull the vinyl hose off the distribution tube.
Disassemble for cleaning:
•
Twist both of the inner tube ends until the tabs line up
with the keyways.
•
Pull the inner tube ends outward.
Part Number 000001528
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
F. Remove the water pump.
Disconnect the water pump power cord.
G. Remove the water trough
•
•
•
•
Remove the quarter turn fasteners (turn
counterclockwise) securing the trough in place.
LOOSEN
SCREWS
Lift up and forward on the front of the water trough
while allowing the rear of the water trough to drop.
Remove the water trough from the ice machine.
POWER
CORD
WATER
PUMP
PUMP
OUTLET
SV1456B
REMOVE THE TWO
1/4 TURN FASTENERS
BY TURNING
•
•
Disconnect the hose from the pump outlet.
COUNTERCLOCKWISE
Loosen the screws securing the pump mounting
bracket to the bulkhead.
SV1771B
•
•
Lift the pump and bracket assembly off the screws.
Remove water pump assembly from ice machine.Do
not soak the water pump motor in cleaner or sanitizer
solution
DO NOT SOAK
WATER PUMP
MOTOR IN
CLEANER OR
SANITIZER
SOLUTIONS
4-4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
Step 7 Mix a solution of cleaner and warm water.
Depending upon the amount of mineral buildup, a larger
quantity of solution may be required. Use the ratio in the
table below to mix enough solution to thoroughly clean
all parts.
Step 10 Mix a solution of sanitizer and warm water.
Solution Type
Water
Mixed With
Sanitizer
6 gal. (23 l)
4 oz (120 ml) sanitizer
Step 11 Use 1/2 of the sanitizer/water solution to
sanitize all removed components. Use a cloth or sponge
to liberally apply the solution to all surfaces of the
removed parts or soak the removed parts in the
sanitizer/water solution. Do not rinse parts after
sanitizing.
Solution Type
Water
Mixed With
Cleaner
1 gal. (4 l)
16 oz (500 ml) cleaner
Step 8 Use 1/2 of the cleaner/water mixture to clean all
components. The cleaner solution will foam when it
contacts lime scale and mineral deposits; once the
foaming stops use a soft-bristle nylon brush, sponge or
cloth (NOT a wire brush) to carefully clean the parts.
Soak parts for 5 minutes (15 - 20 minutes for heavily
scaled parts). Rinse all components with clean water.
Step 12 Use 1/2 of the sanitizer/water solution to
sanitize all foodzone surfaces of the ice machine and bin
(or dispenser). Use a cloth or sponge to liberally apply
the solution. When sanitizing, pay particular attention to
the following areas:
Step 9 While components are soaking, use 1/2 of the
cleaner/water solution to clean all foodzone surfaces of
the ice machine and bin (or dispenser). Use a nylon
brush or cloth to thoroughly clean the following ice
machine areas:
•
•
Side walls
Evaporator plastic parts - including top, bottom and
sides
•
Bin or dispenser
•
•
Side walls
Do not rinse the sanitized areas.
Evaporator plastic parts - including top, bottom, and
sides
Step 13 Replace all removed components.
•
Bin or dispenser
Step 14 Reapply power to the ice machine and place
Rinse all areas thoroughly with clean water.
the toggle switch in the CLEAN position.
Step 15 Wait about two minutes or until water starts to
flow over the evaporator. Add the proper amount of
Manitowoc Ice Machine Sanitizer to the water trough by
pouring between the water curtain and evaporator.
Model
Amount of Sanitizer
Q1400C
5 ounces (150 ml)
Part Number 000001528
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
Step 16 The ice machine will stop after the sanitize
cycle (approximately 30 minutes). Place the toggle
switch in the OFF position and disconnect power to the
ice machine.
!
Warning
Disconnect the electric power to the ice machine at
the electric service switch box..
Step 17 Repeat step 6.
Step 18 Mix a solution of sanitizer and warm water.
Solution Type
Water
Mixed With
Sanitizer
6 gal. (23 l)
4 oz (120 ml) sanitizer
Step 19 Use 1/2 of the sanitizer/water solution to
sanitize all removed components. Use a cloth or sponge
to liberally apply the solution to all surfaces of the
removed parts or soak the removed parts in the
sanitizer/water solution. Do not rinse parts after
sanitizing.
Step 20 Use 1/2 of the sanitizer/water solution to
sanitize all foodzone surfaces of the ice machine and bin
(or dispenser). Use a cloth or sponge to liberally apply
the solution. When sanitizing, pay particular attention to
the following areas:
•
•
Side walls
Evaporator plastic parts - including top, bottom and
sides
•
Bin or dispenser
Do not rinse the sanitized areas.
Step 21 Install the removed parts, restore power and
place the toggle switch in the ICE position.
4-6
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
ADDITIONAL COMPONENT REMOVAL
The following components may be removed for easier
access in some installations or they may need to be
removed and cleaned to correct an operational problem.
!
Warning
Disconnect the electric power to the ice machine at
the electric service switch box and turn off the water
supply before proceeding.
Water Dump Valve
The water dump valve normally does not require
removal for cleaning. To determine if removal is
necessary:
1. Leaving the wires attached, twist coil and rotate it
counter-clockwise1/4 turn.
1. Set the toggle switch to ICE.
2. Lift the coil assembly off the valve body.
2. Verify the water trough fills with water at the
beginning of the freeze cycle.
3. Remove the spring, plunger, and nylon gasket from
the valve body.
3. While the ice machine is in the freeze mode, check
the drain to determine if the dump valve is leaking. If
there is water exiting the ice machine through the
drain during the freeze cycle the dump valve is
leaking.
NOTE: At this point, the water dump valve can easily be
cleaned. If complete removal is desired, continue with
step 4.
NOTE: During cleaning, do not stretch or damage the
spring.
A. If the dump valve is leaking, remove,
disassemble and clean it.
4. Remove the tubing from the dump valve by twisting
the clamps off.
B. If the dump valve is not leaking, do not remove
it. Instead, follow the “Ice Machine Cleaning
Procedure”.
5. Twist the valve body to remove from mounting
bracket.
Follow this procedure to remove the dump valve.
COIL
SPRING
NYLON GASKET
PLUNGER
DO NOT
DISCONNECT
WIRES AT COIL
DIAPHRAM
COIL
DRAIN
HOSE
MOUNTING BRACKET
SV1772
VALVE BODY
Dump Valve Disassembly
Part Number 000001528
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
Ice Machine Inspection
Cleaning the Condenser
Check all water fittings and lines for leaks. Also, make
sure the refrigeration tubing is not rubbing or vibrating
against other tubing, panels, etc.
GENERAL
!
Warning
Disconnect electric power to the ice machine head
section and the remote condensing unit at the
electric service switches before cleaning the
condenser.
Do not put anything (boxes, etc.) on the sides or back of
the ice machine. There must be adequate airflow
through and around the ice machine to maximize ice
production and ensure long component life.
Exterior Cleaning
A dirty condenser restricts airflow, resulting in
excessively high operating temperatures. This reduces
ice production and shortens component life. Clean the
condenser at least every six months.
Clean the area around the ice machine as often as
necessary to maintain cleanliness and efficient
operation. Use cleaners designed for use with stainless
steel products.
!
Warning
Sponge any dust and dirt off the outside of the ice
machine with mild soap and water. Wipe dry with a
clean, soft cloth.
The condenser fins are sharp. Use care when
cleaning them.
Heavy stains should be removed with stainless steel
wool. Never use plain steel wool or abrasive pads. They
will scratch the panels.
Shine a flashlight through the condenser to check for dirt
between the fins. To remove dirt:
A. Blow compressed air or rinse with water from
the inside out (opposite direction of airflow). Be
careful not to bend the fan blades.
B. Use a commercial condenser coil cleaner if
required to remove dirt/grease. Follow the
directions and cautions supplied with the
cleaner.
C. Straighten any bent condenser fins with a fin
comb.
“COMB” DOWN
ONLY
CONDENSER
FIN
COMBS
SV1515
Straighten Bent Condenser Fins
4-8
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
Water-Cooled Condenser
and Water Regulating Valve CVD1476 Only
Symptoms of restrictions in the condenser water circuit
include:
•
•
•
•
Low ice production
High water consumption
High operating temperatures
High operating pressures
If the ice machine is experiencing any of these symptoms,
the water-cooled condenser and water regulating valve
may require cleaning due to scale build-up.
Because the cleaning procedures require special pumps
and cleaning solutions, qualified maintenance or service
personnel must perform them.
Part Number 000001528
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
CVD 1476 WATER COOLED CONDENSING UNIT
Removal from Service/Winterization
1. Place the ice machine toggle switch into the OFF
position.
GENERAL
Special precautions must be taken if the ice machine is
to be removed from service for an extended period of
time or exposed to ambient temperatures of 32°F (0°C)
or below.
2. “Front seat” (shut off) the receiver service valve.
Hang a tag on the switch as a reminder to open the
valve before restarting.
3. Perform steps 1-6 in previous column.
Caution
!
4. Disconnect the incoming water and drain lines from
the water-cooled condenser.
If water is allowed to remain in the ice machine in
freezing temperatures, severe damage to some
components could result. Damage of this nature is
not covered by the warranty.
5. Insert a large screwdriver between the bottom spring
coils of the water regulating valve. Pry upward to
open the valve.
Follow the applicable procedure below.
1. Move the ICE/OFF/CLEAN switch to OFF.
2. Disconnect the electric power at the circuit breaker
or the electric service switch.
3. Turn off the water supply.
4. Remove the water from the water trough.
5. Disconnect and drain the incoming ice-making water
line at the rear of the ice machine.
6. Energize the ice machine and wait one minute for
the water inlet valve to open.
7. Blow compressed air in both the incoming water and
the drain openings in the rear of the ice machine
until no more water comes out of the inlet water lines
or the drain.
8. Make sure water is not trapped in any of the water
lines, drain lines, distribution tubes, etc.
9. “Frontseat” (shut off) the receiver service valves.
Hang a tag on the switch as a reminder to open the
valves before restarting.
SV1624
Pry Open the Water Regulating Valve
6. Hold the valve open and blow compressed air
through the condenser until no water remains.
4-10
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
Checklist
Before Calling For Service
Section 5
Before Calling For Service
If a problem arises during operation of your ice machine, follow the checklist below before calling service. Routine
adjustments and maintenance procedures are not covered by the warranty.
Problem
Possible Cause
To Correct
Ice machine does not operate.
No electrical power to the ice machine
and/or condensing unit.
Replace the fuse/reset the breaker/turn
on the main switch.
High pressure cutout tripping.
Clean condenser coil. (See Section 4)
ICE/OFF/CLEAN toggle switch set
improperly.
Move the toggle switch to the ICE
position.
Water curtain stuck open.
Water curtain must be installed and
swinging freely. (See Section 4)
Remote receiver service valve and/or
Liquid/suction line shut off valves are
closed.
Open the valve(s). (See Section 2)
Ice machine stops, and can be restarted Safety limit feature stopping the ice
Refer to “Safety Limit Feature” on the
next page.
by moving the toggle switch to OFF and
back to ICE.
machine.
Ice machine does not release ice or is
slow to harvest.
Ice machine is dirty.
Ice machine is not level.
Clean and sanitize the ice machine.
(See Section 4)
Level the ice machine. (See Section 2)
Low air temperature around ice machine Air temperature must be at least 35°F
head section.
(1.6°C).
CVD1476 - Water regulating valve
incorrectly adjusted or will not close.
Check for water at condenser water drain
outlet. Contact a qualified service
company to adjust/replace valve.
CVD1475 - Fan cycling control does not Verify pressure is below cut-out setpoint,
de-energize condenser fan motor.
replace fan cycling control.
Ice machine does not cycle into harvest
mode.
The six-minute freeze time lock-in has
not expired yet.
Wait for the freeze lock-in to expire.
Ice thickness probe is dirty.
Clean and sanitize the ice machine.
(See Section 4)
Ice thickness probe is disconnected.
Connect the wire.
Ice thickness probe is out of adjustment. Adjust the ice thickness probe.
(See Section 3)
Uneven ice fill (thin at the top of
evaporator).
Verify sufficient water level in sump
trough. Contact a qualified service
company to check refrigeration system.
Ice quality is poor (soft or not clear).
Poor incoming water quality.
Contact a qualified service company to
test the quality of the incoming water and
make appropriate filter
recommendations.
Water filtration is poor.
Ice machine is dirty.
Replace the filter.
Clean and sanitize the ice machine.
(See Section 4)
Water dump valve is not working.
Disassemble and clean the water dump
valve. (See Section 4)
Water softener is working improperly (if
applicable).
Repair the water softener.
Part Number 000001528
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling For Service
Section 5
Problem
Possible Cause
To Correct
Ice machine produces shallow or
incomplete cubes, or the ice fill pattern on
the evaporator is incomplete.
Ice thickness probe is out of adjustment. Adjust the ice thickness probe.
(See Section 4)
Water trough level is too high or too low. Check the water level probe for damage.
(See Section 3)
Water inlet valve filter screen is dirty.
Remove the water inlet valve and clean
the filter screen. (See Section 4)
Water filtration is poor.
Hot incoming water.
Replace is filter.
Connect the ice machine to a cold water
supply. (See Section 2)
Incorrect incoming water pressure.
Ice machine head section is not level.
Water pressure must be 20-80 psi
(137.9 - 551.5 kPA)
Level the ice machine head section.
(See Section 2)
Low ice capacity.
Water float valve filter screen is dirty.
Incoming water supply is shut off.
Water float valve stuck open or leaking.
Clean the filter screen. (See Section 4)
Open the water service valve.
Clean or replace the water float
valve.(See Section 4)
The condenser is dirty.
Clean the condenser. (See Section 4)
High air temperature around condenser
unit.
Air temperature must not exceed
CVD1475 - 130°F (54.4°C)
CVD1476 - 110°F (43.3°C)
1. Move the ICE/OFF/CLEAN switch to OFF and then
back to ICE.
Safety Limit Feature
In addition to the standard safety controls, such as the
high pressure cutout, your Manitowoc ice machine
features built-in safety limits which will stop the ice
machine if conditions arise which could cause a major
component failure.
A. If the safety limit feature has stopped the ice
machine, it will restart after a short delay.
Proceed to step 2.
B. If the ice machine does not restart, see “Ice
machine does not operate” on the previous
page.
Before calling for service, re-start the ice machine using
the following procedure:
2. Allow the ice machine to run to determine if the
condition is recurring.
A. If the ice machine stops again, the condition has
recurred. Call for service.
B. If the ice machine continues to run, the condition
has corrected itself. Allow the ice machine to
continue running.
5-2
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
Before Calling For Service
THIS PAGE INTENTIONALLY LEFT BLANK
Part Number 000001528
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling For Service
Section 5
THIS PAGE INTENTIONALLY LEFT BLANK
5-4
Part Number 000001528
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manitowoc Ice, Inc.
Manitowoc Foodservice International Manitowoc (China) International Refrigeration
2110 South 26th Street
P.O. Box 1720
Manitowoc, WI 54221-1720
Phone: (920) 682-0161
Service Fax: (920) 683-7585
S.A.S.
Company, LTD
18 Chemin de Charbonnières
F-69132 Ecully Cedex
Téléphone : +33 (0)4 72 18 22 50
Fax : +33 (0)4 72 18 22 60
Telephone: 86-571-86888688
No. 151 Jiam Ye Road
Hangzhou Hi-Tech Industry Development Zone
(Bin Jiang)
Hangzhou, Zhejiang 310052
Service Fax: 86-571-86622707
MANITOWOC ICE, INC.
© 2006 Manitowoc Ice, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|