OWNER’S MANUAL
™
Gourmet Series Marine Gas Grill
Model A10-918L
For questions regarding performance, assembly,
operation, parts, or returns, contact the experts
at MAGMA by calling (562) 627-0500
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru
Friday or e-mail us at [email protected]
Read these instructions carefully before use. Familiarize yourself with the appliance before
connecting it to its gas container. Keep these instructions for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNT HARDWARE
Fasteners are supplied for both Single Mount and Dual Mount grill mounting
options. See Magma Catalog or Website for best mount selection.
Single mount through-bolt applications
Dual mount applications
4 Carriage bolts & lock nuts.
4 Carriage bolts & lock nuts. Only 4 bolts
required for grill mounting. Place bolts (2 per
side) diagonally from each other as shown.
Single mount non-through-bolt
applications, including Style 1 “Levelock”
4 Hex head bolts & lock washers.
Carriage bolt
& lock nut
Hex head bolt
& lock washer
See Magma website for
replacement part numbers
and valve applications.
Thermometer
Lid Lock
Grill Grates
Radiant Plate
Burner
Liner
Outer Shell
Valve Chamber
Match Light
Hole
Control Valve
Regulator
Type 1 Low-
Output Shown
Mount Support
Pad with
Folding Legs
Slide Out
Piezo Igniter
Grease Tray
3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING PROCEDURES
OPERATE ONLY ON “LOW” WHEN LID IS CLOSED.
ALWAYS OPERATE WITH GREASE TRAY IN PLACE.
WARNING: Do not overheat grill. Magma Grills do not require pre-heating. Stainless Steel loses
anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low
temperature with the lid closed. If medium or high heat is required, grill with lid open.
LIGHTING INSTRUCTIONS
• Open lid during lighting.
• Depress knob and rotate counter-clockwise to the “HIGH” flame
position.
• Push Piezo Igniter. • Visually confirm ignition. • Turn knob to adjust flame.
• If grill does not light, adjust electrode until proper spark appears (see page 5).
•
If the piezo ignition continues to fail to ignite the gas, see MATCH LIGHTING INSTRUCTIONS.
NOTE: Before lighting, lid lock must be positioned not to engage. Open lid and turn lock to
locked position.
MATCH LIGHTING INSTRUCTIONS
(Back up system allows use of grill until piezo ignition system is repaired.)
• Open lid during lighting. • Place flame up to burner through the match light hole.
• Depress valve and turn counter-clockwise to the “HIGH” flame
• Visually confirm ignition.
position.
TO REDUCE FLARE-UP
• Empty and clean grease tray prior to each use.
• Trim excess fats from meat.
• Reduce heat.
• Use non-oil based marinades.
• Use water spray directly on flare-ups.
FOLDING LEGS
For storage, transport or while using other mounting options. Fold up back legs first, then front
legs (as shown). If legs become loose they can be tightened with a 5/32” Hex Key Wrench.
PRACTICAL HINTS:
Before lighting your grill, be sure that …
•
•
•
•
•
•
Grill is secure and properly mounted.
Internal components and grease tray are clean and correctly positioned.
You have plenty of gas in the canister.
Gas canister is attached properly and there are no gas leaks.
Lid lock has been set not to engage.
You have a water spray bottle handy to cool a hot grill or stop any flare-ups.
STOWING TIPS
• Always disconnect the fuel canister from the valve prior to stowing.
• Stow the valve in a clean, dry area to protect from corrosion to valve.
•
Always store propane in a sealed propane storage locker that allows leakage to vent overboard
or use Magma Propane Storage/Locker Tote Bag. Never stow below decks
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRODE SPARK ADJUSTMENT
CAUTION: Spark can cause small shock. Do not leave
fingers on or near electrode wire while engaging igniter.
• Electrode wire should be approximately 1/8” from gas
exit hole in burner. Carefully adjust wire if required.
A
DISASSEMBLY & RE-ASSEMBLY
Lift radiant plate up & out of left slot (see B) and remove by sliding it out of
right slot (see C).
•
•
Remove burner screw (see B) and remove burner. Check burner for grease
residue or spider webs that may obstruct gas flow. CAUTION: WHEN
REPLACING BURNER, CUT SLOT IN BURNER MUST FACE DOWN.
To remove liner from outer shell you must disconnect the electrode wire
(see D). First remove the two screws on valve chamber (see D) and remove
the cover plate. Gently pull wire off connector (see D). It is not necessary to
remove electrode from liner.
Remove Lid and liner by removing hinge screws and lock nuts with 3/16”
hex key wrench (supplied) and 1/2” wrench or pliers. CAUTION: LOCK NUTS
MUST BE INSTALLED WITH LOCKING INDENT MARKS SHOWING (see E).
IMPROPER INSTALLATION WILL DAMAGE THE HINGE SCREW AND LOCK NUT.
Lift liner out of outer shell by lifting up on liner lip on back side of liner
(see F). When replacing liner, be sure top lip of liner installs over top edge
of outer shell (start with corners of lip and work in).
•
•
•
• Inspect burner, remove any obstructions.
• Clean as indicated in Maintenance (page 6).
• To re-assemble, reverse the procedure above.
Disconnect wire
B
D
C
Right
side
slot
Left
side
slot
Electrode
Screws
Burner screw
F
E
Liner Lip
Liner
Outer Shell
Locking
Indents
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture.
It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a
protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface
rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry.
Avoid using stainless steel polishes on grill exterior as most leave a residue that may discolor when grill is heated.
Additionally, stainless steel that is exposed to high heat will change color and texture over time. The “amber” color of
grill exterior and internal components is not a failure of the stainless steel and will not affect products operation. When this
happens, we recommend using “Magma Magic” Grill Restorer to remove the “amber” color and return grill to its
original luster. However, prolonged exposure to extreme high heat will cause chromium and nickel to “burn out” of stainless
steel. At this point stainless steel will become more susceptible to corrosion and will start to deteriorate. We recommended
replacement of internal components as they become seriously deteriorated.
We recommend thoroughly cleaning grill and internal components after each outing. Disassemble interior components
and remove all food residue. Use a “Scotch Brite” pad or similar product and “Easy-Off” oven cleaner for cleaning grills
interior components, followed by thoroughly washing with soap and water, rinse with fresh water & dry. AVOID CONTACT
OF OVEN CLEANER WITH SKIN, CONTROL VALVE, IGNITOR ELECTRODE & WIRE, AND BOAT SURFACE. CAUTION: DO NOT
USE ANY TYPE OF ABRASIVE PAD ON EXTERIOR MIRROR FINISH AS IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH.
We recommend covering grill between uses. Grill covers are available at Magma retailers or directly from Magma. See our
website, www.magmaproducts.com
Grill Grates - Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with
soapy water and dry prior to storage.
Ceramic Electrode - Located just beside the burner, it should be kept clean of grease and debris. Be careful not to
damage the ceramic insulation or the wire. See page 5 for electrode spark adjustment.
Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way.
Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the orifice.
Repair/Replacement Parts - All replacement parts are readily available at your Magma Retailers or directly from Magma.
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
• Magma On-Board LPG (Propane) Valves &
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
Hose Kits allow Magma Grills to be installed
within a boats existing on-board, pre-regulated
low pressure LPG (Propane) system.
Align valve stem key
to valve chamber
lock detent and rotate
• Use only Magma Type 3 Low Pressure
LPG (Propane) Valves. See our Valve
Application Guide at www.
MagmaProducts.com for correct valve.
• In North America use Magma A10-225
LPG 10' Gas Grill Connection Kit in
conjunction with Type 3 Valve. Outside
North America check your local dealer for
proper hose and fittings.
Gourmet
Gas Grill
Type 3
Valve
Typical Marine &
R.V. Application
Cylinder Valve
Gauge
Solenoid
• A primary shutoff valve (supplied with
Gas Grill Connection Kit) must be used
with this control valve at point of connection
into your system. This allows shut off of gas
supply to hose leading to grill.
Shut off
valve
To other LPG
appliance
or use cap
Gas Regulator
Propane (LPG)
A10-225 LPG (Propane)
10' Gas Grill Connection Kit
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!! • DO NOT CONNECT A HIGH-PRESSURE SUPPLY HOSE
FROM A NON-REGULATED TANK DIRECTLY TO GRILL.
Magma's grills are designed for use with small disposable propane canisters or with pre-regulated
low-pressure propane and optional low-pressure valves. Running high-pressure propane fuel supply
lines on a boat is in violation of American Boat & Yacht Council (ABYC) guidelines and is not
considered a safe application. Additionally, impurities found in larger refillable propane tanks may
clog the small orifices in the high-pressure control valve/ regulator causing it to lose performance
capabilities and eventually fail. Regulating these tanks to 1/2 PSI and using this pre-regulated
propane with the correct low-pressure valve will insure safe, efficient performance of the grill.
USING GRILL WITH ON-BOARD CNG (NATURAL GAS) SYSTEMS
• Magma on-board CNG (natural gas) valves allow Magma grills to be installed to an existing on-board,
pre-regulated low pressure CNG (natural gas) system.
• Use only Magma Type 4 Low Pressure CNG (natural gas) control valves. Visit out website at
www.MagmaProducts.com to view valve application guide. See your local dealer for proper hose and fittings.
TROUBLE SHOOTING GUIDE
Problem
Possible Cause
Possible Solution
Electrode covered with grease or residue
Igniter/electrode too far from burner
Clean electrode
Adjust electrode until proper spark
appears (see page 5)
Electrode wire loose,
disconnected, or corroded
Clean, adjust & reconnect wire between
igniter & electrode, see Complete
Disassembly (page 5)
Burner will
not light
with igniter
Wire is shorted causing spark from wire
before electrode
No spark being generated
Replace Igniter, Electrode & Wire.
See website for part number
Replace Igniter, Electrode & Wire.
See website for part number
Check fuel level, replace canister or
refill cylinder
No gas flow
Burner will
not light
even with
match
Obstructed gas flow
Excessive cooking temperature
Clean burner and valve orifice.
Remove debris/spider webs
Operate only on low when lid is closed
Reduce flame level
Leave lid open
Flare-up
Use water spray to cool
Grease and/or residue build-up
Excessive fat in meats
Excessive oils in marinades
Obstructed gas flow
Clean components
Trim fat from cuts of meat before grilling
Use non-oil based marinades
Clean burner and valve orifice.
Remove debris/spider webs
Increase flame
Yellow sooty
flame
Flame too low
Wind directly on burner
Obstructed gas flow
Block wind when opening lid
Clean burner and valve orifice.
Remove debris/spider webs
Level Grill
Blow-out
Grill not level
Grease or residue build-up
Excessive fat in meats
Excessive oil in marinades
Clean components
Trim fat from cuts of meat before grilling
Use non-oil based marinades
Hot Spots
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
A
x 4
x 4
x 4
B
A) (1) 3/16” Hex key wrench for lid removel.
B) Pack of (4) 1/4”-20 x 5/8” hex head screws
and internal lock washers for “Levelock”
single mount application.
C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and
lock nuts for dual mount and single mount
applications and table legs.
C
x 4
LIMITED WARRANTY
Magma Products, Inc. guarantees this product to be free from defects in materials or workmanship to the original consumer. This guarantee is for the
periods herein specified when used under normal and reasonable conditions, one (l) year from the date of original purchase. This warranty does not include the
cost of property damage or any inconvenience due to the failure of the product. Nor does it cover damage due to misuse, abuse, accident, or damage resulting
from transportation of the product. Nor does it include damage resulting from the commercial use of this product. Nor does it include, on stainless steel
products, "Surface Rust'; Excessive Corrosion due to exposure to salt water; or Discoloration or Corrosion caused by exposure to excessive heat or failure to
properly clean and care for the stainless steel surfaces. If the product fails to operate due to a defect in materials or workmanship during the warranty period,
the defective part will be repaired or replaced at Magma's option. If you wish to obtain performance under this limited warranty, you should contact Magma's
Customer Service Department via telephone at (562) 627-0500, or via e-mail at [email protected], or via U.S. Postal Service mail at "Magma Products,
Inc., Attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712". The defective part, along with proof of purchase, must be returned postage prepaid to
Magma Products, Inc. We suggest that you keep your purchase receipt as we may require reasonable proof of purchase.
In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling the product, or Magma
Products, Inc., will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer prior to the discovery of
the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment from which it was purchased or to any retail
establishment selling this product in order to obtain performance under this warranty. All implied warranties, including the implied warranties of merchantability
and fitness for a particular purpose, are limited in duration to the express warranty periods specified herein for the parts described herein. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Magma dealers, nor the retail establishment
selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above. Magma's maximum
liability shall not exceed the purchase price of the product paid by the original consumer. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation orexclusions may not apply to you. The warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
MAGMA and the Magma logo are registered trademarks of Magma Products, Inc.
Newport is a trademark of Magma Products, Inc.
Patent pending.
CALIFORNIA PROPOSITION 65 – WARNING – The burning of gas cooking fuel generates some by-products, which are on the list of substances,
which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of
potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care
manual, ensuring you provide good ventilation when cooking with gas.
Magma Products, Inc.
3940 Pixie Avenue, Lakewood, CA 90712 • USA
Phone (562) 627-0500 • e-mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|