LINN KUDOS
A M / F M T U N E R
O W N E R S M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY INSTRUCTIONS
1. Read instructions. Read the safety and operating instructions before
operating the appliance.
2. Retain the instructions. Retain the safety and operating instructions for
future reference.
3. Heed warnings. Observe all warnings on the appliance and in the operating
instructions.
4. Follow instructions. Follow all operating and use instructions.
5. Water and moisture. Do not use the appliance near water, for example near
a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near
a swimming pool and the like.
6. Carts and stands. Use only with a cart or stand that is recommended by the
manufacturer.
6a. An appliance and cart combination should be used with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart to
overturn.
7. Wall or ceiling mounting. Mount to a wall or ceiling only as recommended
by the manufacturer.
8. Ventilation. Site the appliance so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not
be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings, or placed in a built-in installation such as a bookcase
or cabinet that may impede the flow of air through the ventilation
openings.
9. Heat. Site the appliance away from heat sources such as radiators, heaters,
stoves, or other appliances (including amplifiers) that produce heat.
10. Power sources. Connect the appliance to a power supply only of the type
described in the operating instructions or marked on the appliance.
11. Grounding or polarization. Do not defeat the precautions taken to ground
or polarize the supply to the appliance.
12. Power cord protection. Route power cords so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, power sockets, and at the point
where they exit from the appliance.
13. Protective attachment plug. As a safety feature the product is equipped
with an attachment plug containing overload protection. Should the plug
need replacing ensure that a replacement is used which has the same
overload protection as the original.
14. Cleaning. The product should be cleaned only as recommended by the
manufacturer.
15. Power lines. An outdoor antenna should be located away from power lines.
16. Outdoor antenna grounding. If an outdoor antenna is connected to the
tuner/receiver ensure that the antenna system is grounded to provide
some protection against voltage surges and static build up.
In the USA see article 810 of the National Electrical Code ANSI/NFPA 70
concerning installation requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Non-use periods. Unplug the power cord from the outlet if the product will
be unused for a long period of time.
18. Objects and liquid entry. Take care not to let objects or liquids fall into the
product.
19. Damage requiring service. The product should be serviced by qualified
personnel if:
a) The power cord or plug has been damaged.
b) Objects or liquid have fallen into the product.
c) The product has been exposed to rain.
d) The product does not appear to operate normally or exhibits a marked
change in operation.
e) The product has been dropped or the enclosure damaged.
20. Servicing. Don’t attempt to service the product beyond that described in
the operating instructions. All other servicing should be referred to qualified
service personnel.
UK USERS PLEASE READ THIS IMPORTANT SAFETY INFORMATION
Fuse replacement
This appliance is fitted with a non-wireable 13 Amp mains plug. The plug
contains a 5 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the
carrier back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use
the plug. Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this
proceed as follows. If you are in doubt contact your Linn retailer or a
competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points
of most quality plugs.
Attach the wires securely to their respective points. The Brown wire must
go to the Live pin, the Blue wire must go the Neutral pin, and the Green/
Yellow wire must go to the Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding
the outer sheath of the cable firmly and that the wires are correctly
connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright and acknowledgements
Copyright © Linn Products Limited.
Linn Products Limited, Floors Road, Waterfoot, Glasgow, G76 0EP,
Scotland, United Kingdom.
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of the publisher.
Printed in the United Kingdom.
KEILIDH, KUDOS, MAJIK, WAKONDA, and Sneaky are trademarks
of Linn Products Limited.
The information in this manual is furnished for informational use
only, is subject to change without notice, and should not be
construed as a commitment by Linn Products Limited. Linn Products
Limited assumes no responsibility or liability for any errors or
inaccuracies that may appear in this manual.
Part no: PACK 179
This manual was produced by Human-Computer Interface Ltd,
Cambridge, England.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction ........................................ 1
Your Linn system ........................................ 2
KUDOS and music ........................................ 3
Setting up KUDOS ........................................ 5
Unpacking ........................................ 5
Positioning the KUDOS Tuner ........................................ 7
Connecting the KUDOS Tuner ........................................ 8
Choosing an aerial ........................................ 10
FM reception ........................................ 10
AM reception ........................................ 11
Using KUDOS ........................................ 13
Using the front panel ........................................ 13
Switching on and off ........................................ 15
Choosing a station ........................................ 16
Tuning ........................................ 18
Tuning directly to a station ........................................ 20
Setting presets ........................................ 21
Displaying the signal strength ........................................ 23
Setting the muting threshold ........................................ 24
Getting the best reception ........................................ 27
Getting good reception on FM ........................................ 27
Getting good reception on AM ........................................ 29
Guarantee and service ........................................ 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical information ........................................ 33
Tuning ........................................ 33
Specifications ........................................ 35
Index ........................................ 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
We believe that good music is not a luxury, but a necessity, and we
at Linn have dedicated the better part of two decades to making
sure that our customers are given the best possible experience of
the music they love. In other words, we take music seriously, which
is why we dedicate ourselves to building hi-fi which sets the highest
possible standards in bringing music to life within your home.
Listening to your new
KUDOS Tuner should be
the nearest you can get to
being at a superb live
performance.
Listening to your new KUDOS Tuner should be the nearest you can
get to being at a superb live performance. It combines superb
quality, approaching that of CD on the FM waveband, with
unusually high sensitivity, to allow you to reach even quite distant
radio stations. With KUDOS you can now hear radio broadcasts as
they originally sounded, and we want to make sure that you get
the maximum enjoyment possible.
To do that, you need to know exactly how to get the best out of
your KUDOS Tuner and that is what this manual is all about. In the
next few pages you will find out everything you need to know
about how to set up the KUDOS Tuner, and how to use it to get
the best possible results.
We hope that you will spend a few minutes getting to know the
KUDOS Tuner well, and will keep on experimenting and, above all,
enjoying it!
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Linn system
Every hi-fi system has three sections: source, control, and playback.
With Linn hi-fi you have a range of choices for these three sections,
and you have the freedom to extend or improve sections at a later
date.
The ideal starter system incorporating a KUDOS Tuner consists of a
MAJIK control amplifier with on-board stereo power amplifiers, and
a pair of KEILIDH loudspeakers.
The KUDOS Tuner is also an ideal addition to the top Linn
components, to provide superb quality radio reception to an
existing system.
Download from Www.Somanuals.com. All Manuals Search And Download.
KUDOS and music
The KUDOS Tuner is a very flexible radio tuner, giving you
access to both the FM and AM wavebands. It provides
extremely high quality stereo reception on the FM
waveband, combined with very good sensitivity to
allow even distant FM radio stations to be
received with low distortion.
The AM waveband provides good selectivity to
avoid interference between closely spaced
LINN KUDOS
stations.
To select a station you can either enter the frequency directly, or
scan through the wavebands stopping at each station. You can also
define up to 50 numbered presets to make finding your favourite
stations as simple as possible.
NARROW
STEREO
TUNING
BAND
You can control the KUDOS Tuner from the front panel keys, or
using the remote control handset supplied with it. This has a
numeric keypad to allow you to enter frequencies or preset
numbers directly.
KUDOS as a Sneaky module
If you have a MAJIK or WAKONDA amplifier you can choose to
have the KUDOS Tuner fitted as a Sneaky module inside the
amplifier, to make a very compact integrated unit.
The KUDOS Tuner automatically appears as an extra input, leaving
your existing tuner input available for a second tuner, or TV input.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up KUDOS
This chapter explains how to unpack your KUDOS Tuner, and how
to install it with your other hi-fi components.
It also gives advice on choosing and positioning the aerial to get
best possible reception with your KUDOS Tuner.
Unpacking
The KUDOS Tuner comes in a box with the following accessories:
• a remote control handset
• a mains lead
• two single phono to phono leads
• one spare fuse
• this manual.
We recommend you retain the packaging in case you need to
transport the KUDOS Tuner at a later date.
WARNING: Do not connect the mains supply until you have
verified that the KUDOS Tuner is set to the correct voltage for your
mains supply.
Voltage selection
The KUDOS is factory-set for a 240 volts mains supply and must
not be connected to a mains supply before it is adjusted for your
local voltage, and fitted with the appropriate fuse. To set the
voltage, rotate the voltage selector on the underside of the unit
until the appropriate voltage is aligned with the white marker.
Download from Www.Somanuals.com. All Manuals Search And Download.
To fit the fuse, first identify the correct fuse for your local voltage –
400mA anti-surge for 220V and 240V, and 800mA anti-surge for
100V and 120V. Pull open the fuse drawer at the left-hand side of
the mains inlet, insert the fuse in the rear compartment, and close
the drawer.
WARNING: This appliance must be earthed. Use the earthed
moulded mains lead supplied. Never use an unearthed plug or
adaptor.
Important note for UK use
The wires in this mains lead use the following colour code:
• Green and yellow Earth
• Blue
Neutral
Live
• Brown
As the colours of the wires in the mains lead of this appliance may
not correspond with the coloured marking identifying the terminals
in your plug, proceed as follows:
Connect this wire
Green and yellow
To the terminal
Marked with the letter E, or by the earth
symbol, or coloured green or green and yellow.
Blue
Marked with the letter N or coloured black.
Marked with the letter L or coloured red.
Brown
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the KUDOS Tuner
You can position your KUDOS Tuner almost anywhere you find
convenient, but the following considerations may be useful.
The Linn remote control system is exceptionally sensitive. You
should have no problems operating the KUDOS Tuner with the
remote control wherever it is placed in a room, provided you keep
it out of direct sunlight and you do not obscure the control
window. It can even be operated when placed behind smoked-
glass cupboard doors.
The KUDOS Tuner can be placed on top of other Linn products,
provided you allow plenty of air circulation around components
that generate heat, such as the Linn MAJIK amplifier.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the KUDOS Tuner
The following diagrams show the connections for the rear panel of
the stand-alone KUDOS Tuner, and the Sneaky KUDOS Tuner:
Stand-alone KUDOS
FM
AM
REMOTE
CONTROL
ROOM
CONTROL UNIT
ANTENNA ANTENNA
IN
OUT
RCU/ACCESSORY
INFRA
RED
FM AERIAL
GND
AM
REMOTE
AUDIO
OUT
L
R
A
B
MAINS INPUT
MAIN
SPARE
AUDIO OUTTPUTS
Sneaky KUDOS
FM
AM
REMOTE
CONTROL
ROOM
CONTROL UNIT
ANTENNA ANTENNA
IN
OUT
RCU/ACCESSORY
INFRA
RED
FM AERIAL
GND
AM
REMOTE
LINE OUTPUTS
OUT TAPE2
IN
OUT TAPE1 IN
AUX1
L
CD
TUNER
AUX2
L
L
L
L
R
R
R
R
R
MAINS INPUT
SPARE
TUNER INPUT
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the mains supply
Connect the KUDOS Tuner to a mains supply using the mains cord
supplied with it.
Note that the KUDOS Tuner should be switched off before
connecting or disconnecting any of the plugs on the rear panel, or
you may generate surges which could damage other components
in your hi-fi system.
Connecting the stand-alone KUDOS Tuner audio output
The stand-alone KUDOS Tuner provides two pairs of phono audio
outputs. Connect one pair of outputs to the radio or line input of
your preamplifier using the phono cables provided. The other pair
of outputs are provided to allow you to connect to a second
preamplifier or a multi-room system.
Connecting the Sneaky KUDOS Tuner
The Sneaky KUDOS Tuner is connected internally to the MAJIK
amplifier or WAKONDA preamplifier, and you do not need to make
any further audio connections.
Connecting the aerial
The KUDOS Tuner requires external FM and AM aerials to receive
stations on the corresponding wavebands. For more information
about choosing and positioning each type of aerial refer to the
next section, Choosing an aerial.
Download from Www.Somanuals.com. All Manuals Search And Download.
Choosing an aerial
The KUDOS Tuner is capable of providing an extremely high-quality
signal, with low distortion and very good sensitivity. However, its
performance is determined by the quality of the signal you provide
to it, and this is dependent on the type of aerial you are using.
The type of aerial you will need depends on the quality of reception
in your area, and so it is difficult to give specific recommendations.
However this section describes the range of options available, with
recommendations to help you choose the best one.
Your Linn dealer can offer advice relevant to your area, and help
you install a suitable antenna.
FM reception
For best results, the FM antenna should provide a signal strength of
at least 70dBµV for strong stations, which corresponds to a reading
of S70 on the KUDOS display.
Ribbon antenna
If you are in an area of high signal strength, you may find that a
ribbon antenna, also referred to as a split-flex dipole, gives
acceptable results. However, they are prone to fading, and the
signal can be affected when you walk around the room. They are
also prone to interference from computers or televisions in the
same room, so it is best to install them away from electrical
equipment, such as near a window. A balun transformer is often
recommended at the antenna end of the cable, but in practice this
may make little difference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Whip antenna
A whip antenna can work well, and is not directional.
Three element antenna
For best reception use a three-element antenna. This can add up to
10dBµV to the received signal strength, and mounting the antenna
higher, such as in a loft, can add a further 10dBµV. A three-element
antenna is highly directional and so should be oriented for best
results.
AM reception
For best results use a large loop of wire, six feet across or more.
This will pick up strong signals with a minimum of interference. The
loop antenna is directional and it should be mounted vertically,
facing the stations you want to receive. Keep it away from
computers, televisions, and mains wiring to minimise interference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using KUDOS
This chapter explains everything you need to know to use KUDOS,
from switching it on and off to setting up presets for your favourite
stations.
Using the front panel
We designed the KUDOS Tuner to be as simple as possible to
operate. The front panel display gives clear information about what
you are doing and, although there are many sophisticated features,
all the most commonly-used ones require only one key press.
Remote control
The KUDOS Tuner is supplied with a remote control, and this
provides access to all of the functions available from the front
panel, in addition to being able to let you enter preset numbers
and station frequencies directly from a numeric keypad.
The illustrations on the next page explain the function of each of
the control keys, and the meaning of the different parts of the
display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Stand-alone KUDOS
FREQUENCY/PRESET
NUMBER
FM
AM
PRESET
SCAN
WAVEBAND
TUNING MODE
103
.4
STEREO/MONO
NARROW/WIDE
BANDWIDTH
STEREO
NARROW
TUNE, SCAN, OR
SELECT PRESET
SWITCH BETWEEN
STEREO/MONO
BAND
TUNING
STEREO
NARROW
SELECT
WAVEBAND
SELECT TUNING
MODE
SWITCH BETWEEN
NARROW/WIDE
Sneaky KUDOS
FREQUENCY/PRESET
NUMBER
FM
AM
PRESET
WAVEBAND
TUNING MODE
SCAN
103
.
STEREO/MONO
NARROW/WIDE
BANDWIDTH
STEREO
NARROW
TUNE, SCAN, OR
SELECT PRESET
T
U
N
M
AM
FM
O
D
MUTE
VOL –
VOL +
INPUT
INPUT
LISTEN
SELECT
WAVEBAND
SELECT TUNING
MODE
SWITCH BETWEEN
NARROW/WIDE
AND STEREO/MONO
Download from Www.Somanuals.com. All Manuals Search And Download.
The function of each key is explained in the following table:
Press this key
BAND
To do this
Switch between AM and FM. In Europe the AM
band includes both medium wave and long
wave.
TUNING
Change the tuning mode between direct tuning,
signal strength display, preset mode, and scan
mode.
< and >
Change the frequency or preset, or scan,
depending on the tuning mode.
STEREO
Switch between Mono and Stereo operation.
The STEREO display will show whether the
station can be received in stereo.
NARROW
MOD
Switch between wide and narrow bandwidths.
NARROW is displayed in narrow mode.
Sneaky KUDOS only. Steps between the
different combinations of stereo and narrow.
Switching on and off
Switching on
To switch KUDOS on press the power button. The tuner will select
preset 0 and the display shows:
FM
PRESET
P 00
You can store your favourite station as preset 0 so that it is selected
whenever you switch on; for information about doing this see
Setting presets, page 21.
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching off
To switch off press the power button again.
To select the KUDOS Tuner
The stand-alone KUDOS will normally be connected to the tuner
input on your amplifier. Select it in the normal way; for example, by
pressing the TUNER key on the remote control.
To select the Sneaky KUDOS Tuner
The Sneaky KUDOS appears as an additional input on the amplifier,
leaving the original tuner input free for a second tuner.
When you first switch on the amplifier the KUDOS Tuner is
automatically selected as the input, with preset 0 chosen.
Remote: Press the WHERE key. On other remote controls this is
marked ZONE or MATRIX.
Choosing a station
The KUDOS Tuner allows you to store up to 50 stations as presets,
so that you can tune to them directly simply by entering the
number of the preset. The presets can be freely mixed between
AM and FM and, in addition to the station frequency, the preset
also stores the options selected for best reception of that station:
mono/stereo and narrow/wide.
Download from Www.Somanuals.com. All Manuals Search And Download.
To select a preset
92
.3
Press the TUNING key (TUN on the Sneaky KUDOS) until the
PRESET light illuminates on the front panel.
TUNING
Then press < or > until the display shows the preset you want to
select; for example P 03 .
FM
PRESET
P 00
STEREO
Hold down the < or > button to step quickly between presets.
Remote: Press PRESET to select preset mode, and then press
+ or - to select a preset. Hold down + or - to step
between presets.
FM
PRESET
P 03
STEREO
To enter a preset number directly
Using the remote control you can type a preset number directly as
follows.
If you have been controlling another source, such as a CD player,
first select the tuner by pressing TUN on the remote control (or
WHERE for a Sneaky KUDOS).
Then press PRESET to select preset mode.
To select a preset from 0 to 9 press the corresponding number on
the remote control.
To select a preset above 9 press and hold the first digit until it
appears as the left-hand digit of the preset number; for example:
FM
PRESET
P 1-
STEREO
Then press the second digit.
Download from Www.Somanuals.com. All Manuals Search And Download.
To display the preset frequency
FM
PRESET
P 03
STEREO
Once you have selected a preset you can display the frequency of
the preset you have selected by pressing the TUNING key (TUN on
the Sneaky KUDOS).
TUNING
FM
91.1
STEREO
Tuning
The KUDOS Tuner lets you find a frequency by tuning manually, or
you can scan automatically to find the next station. When you are
scanning the tuner will only stop on stations above the muting
threshold; for more information see Setting the muting threshold,
page 24.
To select the band
Press the BAND key (AM/FM on the Sneaky KUDOS) to change
between FM and AM. The display shows the current band; for
example:
AM
5 2 2
NARROW
Download from Www.Somanuals.com. All Manuals Search And Download.
To scan for a station
FM
8 8
.9
STEREO
Press the TUNING key (TUN on the Sneaky KUDOS) until the
display shows SCAN.
TUNING
Then press < or > to scan up or down in frequency to the next
station. The KUDOS Tuner will stop scanning when it finds a
station.
FM
SCAN
8 8
.9
STEREO
To cancel scanning before a station is found press the TUNING
button again (TUN on the Sneaky KUDOS).
FM
SCAN
91.1
STEREO
Press and hold the < or > key to scan quickly through the
frequencies, without stopping on any stations. Normal scanning
resumes when you release the button.
To tune more accurately when scanning, KUDOS automatically
selects narrow tuning mode. After cancelling scanning you may
wish to select wide tuning mode again for best reception.
Remote: Press SCAN to select scan mode, and then use the + or -
keys to scan up or down in frequency.
To use the long waveband (Europe only)
The long waveband is joined to the medium wave (AM) band, and
scanning beyond the medium waveband scans into the long
waveband, and vice-versa.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning directly to a station
If you know the frequency of the station you want to listen to you
can select it from the front panel, or enter it directly from the
remote control.
To tune directly to a station
FM
91
91
.1
STEREO
Press the TUNING button on the front panel (TUN on the Sneaky
KUDOS) until the scan and preset lights disappear and the current
frequency is displayed.
Use the < and > keys to tune to the frequency you want to select.
FM
.2
STEREO
Press and hold down the < or > key to tune quickly through the
frequencies.
Tuning is performed in steps of 100kHz (Europe) or 50kHz (USA).
Remote: Press the TUNE button to select tuning mode and then
use the + or - keys to move up or down in frequency.
To enter a frequency directly
You can use the remote control to tune by entering a frequency
directly.
If you have been controlling another source, such as a CD player,
first select the tuner by pressing TUN on the remote control (or
WHERE for a Sneaky KUDOS).
Press the TUNE key to select tuning mode.
Then type the frequency in 50kHz steps. For example, to enter
101.7MHz key 10170, or to enter 99.95MHz key 9995.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting presets
The KUDOS Tuner allows you to store up to 50 stations as presets
so that you can select them by entering the number of the preset.
The preset remembers not only the frequency, but also the other
settings you have selected for best reception of that station:
narrow or wide, and mono or stereo.
The simplest way to define presets is to use the remote control.
You can also define them using the front panel, but this requires
more key presses.
To store a preset using the remote control
First tune the KUDOS Tuner to the station you want to store. You
can also choose narrow or wide, and stereo or mono for best
reception.
FM
98
.7
STEREO
STORE
FM
Then press the STORE key on the remote control.
S t10
Press the + or - keys to select the number of the preset you want
–
+
to use; for example, S t12 .
FM
S t12
Then press and hold down the STORE key on the remote control to
store the preset until the display changes to PRESET mode; for
example P12 .
STORE
FM
PRESET
P 12
Alternatively, if you decide not to store the preset press one of the
other keys to return to normal operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
To store a preset using the front panel
FM
98
.7
STEREO
If the KUDOS Tuner is not in direct tuning mode, press the
TUNING key (TUN on the Sneaky KUDOS Tuner) so that the SCAN
and PRESET lights disappear and the current frequency is
displayed.
TUNING
FM
S 3 7
th 2
Press and hold the TUNING key until the display shows the current
threshold setting; for example, th 2 .
FM
Then press the TUNING key again to display the preset to be
stored; for example S t10.
TUNING
Choose the number of the preset you want to use, using the
FM
FM
FM
> or < keys.
S t10
Then press and hold the TUNING key until the display returns to
preset mode and displays the preset you defined; for example,
P 12 .
S t12
The preset is now stored.
TUNING
PRESET
P 12
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear a preset
FM
S t14
Enter store mode and select the preset, as if you were going to
store into it.
TUNING
The display should show the number of the preset you want to
clear; for example S t14.
FM
PRESET
P 14
Now press and hold the TUNING key on the front panel (TUN on
the Sneaky KUDOS) until the display shows, for example C14. The
preset will then revert to the factory-stored default.
FM
PRESET
C 14
Displaying the signal strength
The KUDOS Tuner allows you to display the signal strength of any
station, to help you to choose the best frequency for a station, or
to enable you to set up an antenna for best reception.
The signal strength is displayed as a number between 0 and 99 in
dBµV. For good AM reception the signal strength should be
between 30 and 50dBµV. For good FM reception the signal
strength should be at least 70dBµV on strong stations.
To display the signal strength
FM
98
.7
STEREO
Press the TUNING key (TUN on the Sneaky KUDOS) until the
display shows the current signal strength. For example S 75 .
TUNING
FM
S 75
STEREO
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the muting threshold
The KUDOS Tuner allows you to set a muting threshold, to reject
weak signals while you are tuning or scanning.
Signals below the muting threshold will be muted, and signals near
the muting threshold will be set to mono to eliminate noise. When
scanning the KUDOS Tuner will not stop on signals below the
muting threshold.
By default the muting threshold is set to 2. You can set it to a value
between 0 and 4 to determine the approximate threshold, as
shown in the following table:
Threshold setting
Description
0
Accept all signals. In FM you will hear a loud
hiss between stations.
1
2
3
4
Reject signals below signal strength 10µV.
Reject signals below signal strength 20µV.
Reject signals below signal strength 30µV.
Reject signals below signal strength 40µV.
You can set the muting threshold independently for the AM and
FM bands so, for example, if you have strong FM signals you can
set a different threshold.
Download from Www.Somanuals.com. All Manuals Search And Download.
To alter the muting threshold
FM
98
.7
STEREO
Press the TUNING key (TUN on the Sneaky KUDOS) until the
SCAN and PRESET lights disappear.
TUNING
Then press and hold the TUNING key until the display shows the
signal strength, followed by the current muting threshold; for
example th 2 .
FM
S 3 7
th 2
FM
Then use > and < keys to set the threshold to the value you want to
use.
You can change band using the BAND key (FM/AM on the Sneaky
KUDOS) to view and adjust the threshold for the other band if you
wish.
FM
FM
FM
th 4
Finally, to store the new muting threshold press the TUNING key
TUNING
again (TUN on the Sneaky KUDOS) until the display shows PRESET.
S t14
TUNING
PRESET
P 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting the best
reception
The KUDOS Tuner is capable of giving superb results even with
relatively poor signals. However, to hear it at its best you need to
provide a good quality input signal. The signal affects the reception
in two ways:
• If the signal is not strong enough you will hear noise as a hiss in
the background on weak stations.
• If interference is being received you will hear buzzing or
whistling noises in the background.
This chapter provides guidelines to help you get the best possible
reception on FM and AM with your KUDOS tuner.
Getting good reception on FM
Minimising noise
For the best signal-to-noise ratio your aerial should provide a signal
strength of at least 70dBµV, corresponding to a reading of S70 on
the KUDOS display, for the majority of stations you listen to
regularly. If the received signal is not strong enough noise will be
heard as a hiss in the background on weak stations.
There is no disadvantage in having a higher signal strength,
although if the signal strength is greater than 99dBµV on the
strongest stations you may need an RF attenuator or a smaller
antenna.
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimising interference
Interference from nearby stations, or from electrical noise sources
such as computers, can be heard as faint rustling or whistling
noises in the background of the signal. The KUDOS tuner is
designed to provide excellent rejection of interference, but the
following guidelines can help if this proves to be a problem.
Select the narrow bandwidth, for the best rejection of adjacent FM
stations.
If the interference is from strong interfering radio stations try
orienting the antenna away from them. You can even install an
antenna rotator to remotely control the antenna direction. Ask your
dealer for assistance.
If the interference is from electronic equipment move the antenna
to another position.
Install a better, more selective, antenna which will pick up the
stronger wanted signals and reject unwanted ones.
If all else fails, try mono. A signal which is unusable in stereo will
often sound better in mono.
Minimising distortion
Unless interference is a problem you can achieve the lowest
possible distortion by selecting the wide bandwidth option.
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting good reception on AM
Although the quality available with AM is obviously lower than with
FM, the KUDOS Tuner is capable of excellent results on AM with a
well set-up aerial.
Minimising noise
Signal strength on AM is less important than on FM. If there is little
interference a signal strength of 30dBµV is usable, and there is not
much advantage of signal strengths greater than 50dBµV. With
signals weaker than this you can benefit from improving the
antenna.
If you have signals stronger than 99dBµV you may need an RF
attenuator or a smaller antenna to avoid overloading the AM front
end. This will not damage the KUDOS tuner, but may prevent
reception of weaker signals nearby.
Minimising interference
As on FM, interference can be caused by other stations, or by
electrical equipment or wiring.
The best way to avoid interference is to move the antenna away
from interfering electrical equipment, or rotate it to reduce the
strength of interfering stations.
Interference can also be reduced by selecting the narrow
bandwidth, at the expense of high frequency response. Sometimes
the remaining interference can be eliminated by deliberately tuning
up to 4kHz off the correct frequency, away from the interference
above or below the station. This will also increase the high
frequency response again.
Download from Www.Somanuals.com. All Manuals Search And Download.
At night the reception conditions can change dramatically, and
stations you can receive clearly in the daytime may suffer from
interference at night.
Maximising the frequency response
Unless interference is a problem, selecting the wide bandwidth will
give the best possible frequency response. This provides a 7kHz
frequency response which gives much better sound quality than
narrow, which provides a frequency response of only 3.5kHz.
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee and service
This product is guaranteed under the conditions which apply in the
country of purchase.
In addition to any statutory rights the customer may have, we
undertake to replace any parts which have failed due to faulty
manufacture. To help us, please ask your Linn retailer about the
Linn warranty scheme in operation in your country.
In the UK and other markets, extended warranty is offered to
customers who register their purchase with Linn. A registration card
can be obtained from your Linn retailer and should be stamped by
them. This will also enable you to receive the Linn RECORD
newsletter and details of hi-fi and music available from Linn.
Warning
Refer all enquiries to authorised Linn retailers only. Unauthorised
servicing or dismantling of the product invalidates the
manufacturer’s warranty.
If you are in any doubt, please contact your nearest Linn retailer.
For information on your nearest Linn retailer, contact the Linn
factory in Scotland or your national distributor.
Important
1 Please keep a copy of the sales receipt to establish the purchase
date of the product.
2 Please ensure that your equipment is insured by you during any
transit or shipment for repair.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical information
Tuning
Tuning range – USA
FM
87.5 to 108.5MHz
530 to 1730kHz
AM
Tuning range – Europe
FM
87.5 to 108.5MHz
AM
144 to 297kHz and 522 to 1611kHz
Tuning range – Japan
FM
75.5 to 90.5MHz
530 to 1730kHz
AM
A KUDOS Tuner can be converted between USA operation and
European operation by a Linn dealer. The Japanese version is
specific to Japan and cannot be re-configured.
Tuning resolution
AM, TUNE mode
AM, SCAN mode
1kHz
10kHz USA and Japan, 9kHz Europe
AM, direct frequency entry 1kHz
FM, TUNE or SCAN mode 100kHz
FM, direct frequency entry 50kHz
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset tuning
50 presets can be defined, and each stores:
• the wave band
• the frequency
• the STEREO and NARROW options.
The tuner is reset to preset 0 when first switched on.
Signal strength meter
Shows the signal strength in the range 0 to 99dBµV.
Mute/Scan threshold
Adjustable in five steps from fully off, to 30 to 40dBµV muting
sensitivity.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Antenna inputs
Outputs
FM: 75Ω coaxial connector.
AM: Screw terminals
Two pairs RCA phono connectors.
Output impedance 200Ω
Minimum load: 1kΩ total
Output levels
Mains fuse
FM: 775mV rms into 1kΩ at 75kHz peak
deviation.
AM: 775mV rms into 1kΩ at 100% modulation.
220V and 240V: T400mA 50/60Hz
100V and 120V: T800mA 50/60Hz.
Power consumption
Size
20VA approx.
320mm x 326mm x 80mm
(12.6" x 12.8" x 3.2") (W x D x H)
Weight
3.3Kg (7.3lb)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Keys
C
< key 17
> key 17
clearing presets 25
connections 8
aerial 9
audio output 9
mains supply 9
Sneaky KUDOS 8
stand-alone KUDOS 8
copyright iv
A
acknowledgements iv
aerials
choosing 10
connecting 9
loop antenna 11
ribbon antenna 10
three element antenna 11
whip antenna 11
AM reception
D
defining presets 23
distortion
minimising on FM 6
aerials 11
maximising the frequency
response 8
F
FM reception
minimising interference 7
minimising noise 7
AM/FM key 20
antennae. See aerials
aerial 10
minimising distortion 6
minimising interference 6
minimising noise 5
frequency, entering
directly 22
B
band
frequency response,
maximising on AM 8
front panel 15
selecting 20
BAND key 17, 20
Sneaky KUDOS 16
stand-alone KUDOS 16
fuse replacement iii
Download from Www.Somanuals.com. All Manuals Search And Download.
muting threshold
displaying 27
setting 26
G
guarantee 29
specification 32
I
interference 5
minimising on AM 7
minimising on FM 6
introduction 1
N
Narrow key 17
noise 5
minimising on AM 7
minimising on FM 5
K
KEILIDH loudspeakers 2
key functions 17
KUDOS and music 3
P
positioning 7
PRESET display 19
presets
L
clearing 25
long waveband (Europe
only) 21
displaying frequency 20
entering number 19
selecting 19
loop antenna 11
storing using the front panel 24
storing using the remote
control 23
M
mains lead wiring 6
mains plugs i
mains supply
R
connecting 9
reception, getting best 5
remote control 15
replacing the fuse iii
ribbon antenna 10
MAJIK control amplifier 2
MATRIX key 18
MOD key 17
Download from Www.Somanuals.com. All Manuals Search And Download.
tuning 20, 22
S
entering a frequency
directly 22
safety instructions i, ii
SCAN display 21
scanning 21
frequency steps 22
specification 31
using the remote control 21
service 29
with the remote control 22
TUNING key 17
tuning range 31
tuning resolution 31
setting up 5
signal strength
displaying 25
specification 32
Sneaky KUDOS 3
front panel 16
U
unpacking 5
selecting 18
V
specifications 33
stand-alone KUDOS
front panel 16
voltage selection 5
stations, choosing 18
Stereo key 17
storing presets 23
switching off 18
switching on 17
W
waveband
selecting 20
WHERE key 18
whip antenna 11
T
Z
technical information 31
three element antenna 11
ZONE key 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|