Instant Broadband® Series
®
EtherFast Cable/DSL Firewall
Router with 4-Port
Switch/VPN Endpoint
Use this guide to install:
BEFSX41
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Table of Contents
VPN
Password
Status
DHCP
Log
Help
Advanced
Filters
Forwarding
Dynamic Routing
Static Routing
DMZ Host
MAC Address Clone
DDNS
38
51
53
55
57
59
60
61
65
70
71
73
75
76
Chapter 1: Introduction
1
The Linksys EtherFast Cable/DSL Firewall Router with
4-Port Switch/VPN Endpoint
Features
1
1
2
2
4
An Introduction to LANs and WANs
IP Addresses
Network Setup Overview
Chapter 2: Your Virtual Private Network (VPN)
Why Do I Need a VPN?
What is a Virtual Private Network?
5
5
6
Chapter 3: Getting to Know the EtherFast
Cable/DSL Firewall Router
The Router’s Back Panel
9
9
The Router’s Front Panel LEDs
10
Appendix A: Troubleshooting
Common Problems and Solutions
Frequently Asked Questions
79
79
92
Chapter 4: Connect the Router
Overview
12
12
Connecting Your Hardware Together and Booting Up
12
Appendix B: Maximizing VPN Security
96
Chapter 5: Configure the PCs
Overview
Configuring Windows 95, 98, and Millennium PCs
Configuring Windows 2000 PCs
Configuring Windows XP PCs
14
14
15
17
19
Appendix C: Configuring IPSec between a
Windows 2000 or XP PC and the Firewall Router 98
Introduction
Environment
98
98
Step One: Create an IPSec Policy
Step Two: Build Filter Lists
Step Three: Configure Individual Tunnel Rules
Step Four: Assign New IPSec Policy
Step Five: Create a Tunnel Through the Web-based Utility
99
100
105
113
114
Chapter 6: Configure the Router
21
Chapter 7: The Cable/DSL Firewall Router’s
Web-based Utility
27
27
27
28
35
Appendix D: SNMP Functions
116
117
Overview
Quick and Easy Router Administration
Setup
Firewall
Appendix E: How to Ping Your ISP’s E-mail &
Web Addresses
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Chapter 1: Introduction
The Linksys EtherFast Cable/DSL Firewall Router with
Appendix F: Installing the TCP/IP Protocol
120
4-Port Switch/VPN Endpoint
The Linksys Instant Broadband EtherFast Cable/DSL Firewall Router with 4-
Port Switch/VPN Endpoint is the perfect solution for connecting a small group
of PCs to a high-speed broadband Internet connection or a 10/100 Ethernet
backbone. The Router can be configured to limit internal users’ Internet access
based on URLs and/or time periods—URL filtering and time filtering. For
enhanced protection against intruders from the Internet, the Router features an
advanced Stateful Packet Inspection firewall.
Appendix G: Finding the MAC Address and IP
Address for Your Ethernet Adapter
122
126
Appendix H: Glossary
Appendix I: Specifications
Environmental
139
139
Use the Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint to cre-
ate up to two IPSec VPN tunnels, so you can securely connect to the corporate
server from your home office—or any location when you’re on the road. The
Router provides a dedicated port for DMZ hosting and acts as the only exter-
nally recognized Internet gateway on your local area network (LAN). With the
performance and security features of the Cable/DSL Firewall Router with 4-
Port Switch/VPN Endpoint, your network will take advantage of the Internet
while keeping its data secure.
Appendix J: Warranty Information
Appendix K: Contact Information
140
141
Features
•
•
Supports Universal Plug-and-Play
Protects PCs from Ping of Death, SYN Flood, Land Attacks, IP Spoofing,
and Other DoS (Denial of Service) Attacks
Supports Up to Two IPSec Virtual Private Network (VPN) Tunnels
Supports URL Filtering and Time Filtering
Blocks Proxy, Java, ActiveX, and Cookies
Easily Configurable through a Web Browser from Any Networked PC
Supports IPSec and PPTP Pass-Through
Administer and Upgrade Your Router Remotely over the Internet
Supports Traffic and Event Logging
•
•
•
•
•
•
•
•
•
Configurable as a DHCP Server on Your Network
Administers Can Block Specific Internal Users’ Internet Access with
Filtering
•
•
Supports SNMP ver. 2.0 and SNMP MIB I and II
Supports NTP (Network Time Protocol) for Synchronization with Real-
Time Server
•
•
Support for PPPoE Connection
Dedicated Port for DMZ
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Note: Since the Router is a device that connects two networks, it
needs two IP addresses—one for the LAN side, and one for the WAN
side. In this User Guide, you’ll see references to the “WAN IP
address” and the “LAN IP address.”
An Introduction to LANs and WANs
Simply put, a router is a network device that connects two networks together.
In this instance, the Router connects your Local Area Network (LAN), or the
group of PCs in your home or office, to the Wide Area Network (WAN), that
is, the Internet. The Router processes and regulates the data that travels
between these two networks.
Since the Router has firewall security, the only IP address that can be
seen from the Internet for your network is the Router’s WAN IP address.
However, even this WAN IP address for the Router can be blocked, so
that the Router and network seem invisible to the Internet—see the
Blocking WAN Requests description under Filters in “Chapter 7: The
Cable/DSL Firewall Router’s Web-based Utility.”
Think of the Router as a network device with two sides: the first side is made up
of your private LocalArea Network (LAN) of PCs. The other, public side is the
Internet, or the Wide Area Network (WAN), outside of your home or office.
The Router’s firewall (NAT) protects your network of PCs so users on the pub-
lic, Internet side cannot “see” your PCs. This is how your LAN, or network,
remains private. The Router protects your network by inspecting the first pack-
et coming in through the WAN port before delivery to the final destination on
the LAN port. The Router inspects Internet port services like the web server,
ftp server, or other Internet applications, and, if allowed, it will forward the
packet to the appropriate PC on the LAN side.
Dynamic IP Addresses
A dynamic IP address is automatically assigned to a device on the network,
such as PCs and print servers. These IP addresses are called “dynamic”
because they are only temporarily assigned to the PC or device. After a certain
time period, they expire and may change. If a PC logs onto the network (or the
Internet) and its dynamic IP address has expired, the DHCP server will assign
it a new dynamic IP address.
Remember that the Router’s ports connect to two sides: your 10/100 LAN ports
and the Internet WAN port. The WAN and LAN ports transmit data at 10 Mbps
or 100 Mbps.
For DSL users, many ISPs may require you to log on with a user name and
password to gain access to the Internet. This is a dedicated, high-speed con-
nection type called Point to Point Protocol over Ethernet (PPPoE). PPPoE is
similar to a dial-up connection, but PPPoE does not dial a phone number when
establishing a connection. PPPoE also will provide the Router with a dynamic
IP address to establish a connection to the Internet.
IP Addresses
What’s an IP Address?
IP stands for Internet Protocol. Every device on an IP-based network, including
PCs, print servers, and routers, requires an IP address to identify its “location,”
or address, on the network. This applies to both the WAN and LAN connections.
There are two ways of assigning an IP address to your network devices.
DHCP (Dynamic Host Configuration Protocol) Servers
PCs and other network devices using dynamic IP addressing are assigned a new
IP address by a DHCP server. The PC or network device obtaining an IP
address is called the DHCP client. DHCP frees you from having to assign IP
addresses manually every time a new user is added to your network.
Static IP Addresses
A static IP address is a fixed IP address that you assign manually to a PC or
other device on the network. Since a static IP address remains valid until you
disable it, static IP addressing ensures that the device assigned it will always
have that same IP address until you change it. Static IP addresses are com-
monly used with network devices such as server PCs or print servers.
A DHCP server can either be a designated PC on the network or another net-
work device, such as the Router. By default, the Router’s WAN setting is DHCP
client.
If you use the Router to share your cable or DSL Internet connection, contact
your ISP to find out if they have assigned a static IP address to your account.
If so, you will need that static IP address when configuring the Router. You can
get the information from your ISP.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
By default, a DHCP server (LAN side) is enabled on the Router. If you already
have a DHCP server running on your network, you must disable one of the two
DHCP servers. If you run more than one DHCP server on your network, you
will experience network errors, such as conflicting IP addresses. To disable
DHCP on the Router, see the DHCP section in “Chapter 7: The Cable/DSL
Firewall Router’s Web-based Utility.”
Chapter 2: Your Virtual Private
Network (VPN)
Why Do I Need a VPN?
Computer networking provides a flexibility not available when using an archa-
ic, paper-based system. With this flexibility, however, comes an increased risk
in security. This is why firewalls were first introduced. Firewalls help to protect
data inside of a local network. But what do you do once information is sent out-
side of your local network, when emails are sent to their destination, or when
you have to connect to your company's network when you are out on the road?
How is your data protected?
Note: Even if you assign a static IP address to a PC, other PCs can
still use DHCP’s dynamic IP addressing, as long as the static IP
address is not within the DHCP range of the LAN IP Address.
If the dynamic IP addressing fails to provide a dynamic IP address, refer
to “Appendix A: Troubleshooting.”
That is when a VPN can help. VPNs are called Virtual Private Networks
because they secure data moving outside of your network as if it were still with-
in that network.
Network Setup Overview
This user guide covers the basic steps for setting up a network with a router.
After going through “Chapter 3: Getting to Know the EtherFast Cable/DSL
Firewall Router,” most users will only need to use the following chapters:
When data is sent out across the Internet from your computer, it is always open
to attacks. You may already have a firewall, which will help protect data mov-
ing around or held within your network from being corrupted or intercepted by
entities outside of your network, but once data moves outside of your network
—when you send data to someone via email or communicate with an individ-
ual over the Internet—the firewall will no longer protect that data.
•
•
•
Chapter 4: Connect the Router
This chapter instructs you on how to connect the cable or DSL modem to
the Router and connect the PC(s) to the Router.
Chapter 5: Configure the PCs
This chapter instructs you on how to configure your PC(s) for a DHCP con-
nection, if the network settings are not already set to DHCP.
At this point, your data becomes open to hackers using a variety of methods to
steal not only the data you are transmitting but also your network login and
security data. Some of the most common methods are as follows:
Chapter 6: Configure the Router
1) MAC Address Spoofing
This chapter explains how to configure the Router using your web browser
and the Router’s web-based utility. You will configure the Router using the
settings provided by your ISP.
Packets transmitted over a network, either your local network or the Internet,
are preceded by a packet header. These packet headers contain both the source
and destination information for that packet to transmit efficiently. A hacker can
use this information to spoof (or fake) a MAC address allowed on the network.
With this spoofed MAC address, the hacker can also intercept information
meant for another user.
When you’re finished with the basic steps, then you are ready to connect to the
Internet. After the PC(s) can access the Internet through the Router, you can
alter the Router’s settings further; for example, you can adjust security features
and other settings to enable online gaming.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
2) Data Sniffing
There are two basic ways to create a VPN connection:
•
•
Firewall Router to Firewall Router
Computer (using VPN client software that supports IPSec) to Firewall
Router
Data “sniffing” is a method used by hackers to obtain network data as it trav-
els through unsecured networks, such as the Internet. Tools for just this kind of
activity, such as protocol analyzers and network diagnostic tools, are often built
into operating systems and allow the data to be viewed in clear text.
The Firewall Router creates a “tunnel” or channel between two endpoints, so
that data transmissions between them are secure. A computer with VPN client
software that supports IPSec can be one of the two endpoints. Any computer
with the built-in IPSec Security Manager (Microsoft 2000 and XP ) allows the
Firewall Router to create a VPN tunnel using IPSec (refer to “Appendix C:
Configuring IPSec between a Microsoft Windows 2000 or XP PC and the
Firewall Router”). Other versions of Microsoft operating systems require addi-
tional, third-party VPN client software applications that support IPSec to be
installed.
3) Man in the middle attacks
Once the hacker has either sniffed or spoofed enough information, he can now
perform a “man in the middle” attack. This attack is performed, when data is
being transmitted from one network to another, by rerouting the data to a new
destination. Even though the data is not received by its intended recipient, it
appears that way to the person sending the data.
These are only a few of the methods hackers use and they are always develop-
ing more. Without the security of your VPN, your data is constantly open to
such attacks as it travels over the Internet. Data travelling over the Internet will
often pass through many different servers around the world before reaching its
final destination. That's a long way to go for unsecured data and this is when a
VPN serves its purpose.
Firewall Router to Firewall Router
An example of a Firewall Router-to-Firewall Router VPN would be as follows.
(See Figure 2-1.) At home, a telecommuter uses his Firewall Router for his
always-on Internet connection. His router is configured with his office's VPN
settings. When he connects to his office's router, the two routers create a VPN
tunnel, encrypting and decrypting data. As VPNs utilize the Internet, distance
is not a factor. Using the VPN, the telecommuter now has a secure connection
to the central office's network, as if he were physically connected.
What is a Virtual Private Network?
A VPN, or Virtual Private Network, is a connection between two endpoints - a
VPN Router, for instance - in different networks that allows private data to be
sent securely over a shared or public network, such as the Internet. This estab-
lishes a private network that can send data securely between these two locations
or networks.
This is done by creating a “tunnel”. A VPN tunnel connects the two PCs or net-
works and allows data to be transmitted over the Internet as if it were still with-
in those networks. Not a literal tunnel, it is a connection secured by encrypting
the data sent between the two networks.
VPN was created as a cost-effective alternative to using a private, dedicated,
leased line for a private network. Using industry standard encryption and
authentication techniques—IPSec, short for IP Security—the VPN creates a
secure connection that, in effect, operates as if you were directly connected to
your local network. Virtual Private Networking can be used to create secure
networks linking a central office with branch offices, telecommuters, and/or
professionals on the road (travelers can connect to a VPN Router using any
computer with VPN client software that supports IPSec, such as SSH Sentinel).
Figure 2-1
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Important: You must have at least one Firewall Router on one end of
the VPN tunnel. At the other end of the VPN tunnel, you must have a
second Firewall Router or a computer with VPN client software that
supports IPSec.
Chapter 3: Getting to Know the
EtherFast Cable/DSL Firewall Router
The Router’s Back Panel
Computer (using VPN client software that supports IPSec) to Firewall
Router
The Router’s ports, shown in Figure 3-1, are where network cables are con-
nected
The following is an example of a computer-to-Firewall Router VPN. (See
Figure 2-2.) In her hotel room, a traveling businesswoman dials up her ISP. Her
notebook computer has VPN client software that is configured with her office's
VPN settings. She accesses the VPN client software that supports IPSec and
connects to the Firewall Router at the central office. As VPNs utilize the
Internet, distance is not a factor. Using the VPN, the businesswoman now has
a secure connection to the central office's network, as if she were physically
connected.
Figure 3-1
WAN
The WAN (Wide Area Network) port is where you connect
your cable or DSL modem through an Ethernet cable. Your
modem connection will not work from any other port.
Ports 1-3
These three LAN (Local Area Network) ports are where you
will connect networked devices, such as PCs, print servers,
switches, and anything else you want to put on your network.
(These ports auto-detect crossover and straight-through
cables.)
Port 4/DMZ Port 4/DMZ operates like a regular LAN port to connect with
network devices, unless DMZ is enabled through the
Cable/DSL Firewall Router’s web-based utility. Once DMZ is
enabled, this port will be accessible with NO PROTECTION
from the firewall. Be sure to disable the DMZ function through
the web-based utility if you want this port shielded by the
Cable/DSL Firewall Router’s firewall. (This port auto-detects
crossover and straight-through cables.)
Figure 2-2
For additional information and instructions about creating your own VPN,
Configuring IPSec between a Microsoft Windows 2000 or XP PC and the
Firewall Router.”
Power
The Power port is where you will connect the power adapter.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
*
The Reset Button
WAN and LAN LEDs
Briefly pressing the Reset Button will refresh the Cable/DSL Firewall Router’s
connections, potentially clearing any jammed links.
Link/Act Green. The Link/Act LED serves two purposes. If the LED is con-
tinuously lit, the Router is successfully connected to a device
through the corresponding port (1, 2, 3 or 4/DMZ). If the LED is
flickering, the Router is actively sending or receiving data over
that port.
Pressing the Reset Button and holding it in for a few seconds will clear all of
the Cable/DSL Firewall Router’s data. This should be done only if you are
experiencing heavy routing problems, and only after you have exhausted all of
the other troubleshooting options. By resetting the Cable/DSL Firewall Router,
you run the risk of creating conflicts between your PCs’ actual IP Addresses
and what the Cable/DSL Firewall Router thinks their IP Addresses should be.
You may be forced to reboot the entire system(s).
Full/Col
Green. The Full/Col LED also serves two purposes. If this LED is
lit up continuously, the connection made through the correspon-
ding port is running in Full Duplex mode. If the LED flickers, the
connection is experiencing collisions. Infrequent collisions are
normal.
If the Cable/DSL Firewall Router locks up, simply power it down for three to
five seconds by removing the power cable from the Cable/DSL Firewall
Router’s Power Port. Leaving the power off for too long could result in the loss
of network connections.
If this LED flickers too often, there may be a problem with your
connection. See “Appendix A: Troubleshooting” if you encounter
this problem.
100
Orange. The 100 LED lights up when a successful 100Mbps con-
nection is made through the corresponding port.
The Router’s Front Panel LEDs
The Router’s LEDs, shown in Figure 3-2, provide a graphic display of activity.
If this LED does not light up, then your connection speed is 10
Mbps.
Proceed to “Chapter 4: Connect the Router.”
Figure 3-2
Diag
Red. The Diag LED lights up when the Router goes through its self-
diagnosis mode during every boot-up. It will turn off upon successful
completion of the diagnosis.
If this LED stays on for an abnormally long period of time, see
“Appendix A: Troubleshooting.”
DMZ Green. The DMZ LED lights up when the Cable/DSL Firewall
Router’s DMZ function is enabled. Enabling this function will remove
firewall protection from Port 4/DMZ.
Power Green. The Power LED lights up when the Router is powered on.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Repeat the above step to connect
more PCs or network devices to
the Router.
Chapter 4: Connect the Router
Overview
Unlike a hub or a switch, the Router’s setup consists of more than simply plug-
ging hardware together. You will have to configure your networked PCs to
accept the IP addresses that the Router assigns them (if applicable), and you
will also have to configure the Router with setting(s) provided by your Internet
Service Provider (ISP).
Figure 4-2
3. Connect the Ethernet cable from your cable or
DSL modem to the WAN port on the Router’s
back panel, as shown in Figure 4-3. This is the
only port that will work for your modem con-
nection.
The installation technician from your ISP should have left the setup informa-
tion with you after installing your broadband connection. If not, you can call
your ISP to request the data.
Once you have the setup information you need for your specific type of Internet
connection, you can begin installation and setup of the Router.
Figure 4-3
4. As shown in Figure 4-4, connect the power
adapter to the Power port on the back panel of
the Router, and then plug the power adapter
into a power outlet.
The diagram in Figure 4-1 shows a typical configuration.
Notebook with Ethernet Adapter
WAN
Cable or DSL
Modem
LAN
Figure 4-4
The Power LED on the front panel will light up green as soon as the power
•
•
adapter is connected properly. (The LEDs are shown in Figure 4-5.)
Cable/DSL Firewall Router
PC with Ethernet Adapter
The Diag LED will light up red for a few
seconds when the Router goes through its
self-diagnostic test. This LED will turn
off when the self-test is complete.
Figure 4-1
Figure 4-5
Connecting Your Hardware Together and Booting Up
1. Before you begin, make sure that all of your hardware is powered off,
including the Router, PCs, hubs, switches, and cable or DSL modem.
5. Turn on the cable or DSL modem and PCs.
2. Connect one end of an Ethernet cable to one of the LAN ports (labeled 1,
2, 3, or 4/DMZ) on the back of the Router, and the other end to a standard
port on a network device, e.g., a PC, print server, hub, or switch (see Figure
4-2).
The Router’s hardware installation is now complete.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Configuring Windows 95, 98, and Millennium PCs
Chapter 5: Configure the PCs
1. Go to the Network screen by clicking the Start button. Click Settings and
Overview
then Control Panel. From there, double-click the Network icon.
The instructions in this chapter will help you configure each of your comput-
ers to be able to communicate with the Router.
2. On the Configuration tab, shown in Figure 5-1, select the TCP/IP line for
the applicable Ethernet adapter. Do not choose a TCP/IP entry whose name
mentions DUN, PPPoE, VPN, or AOL. If the word TCP/IP appears by
itself, select that line. (If there is no TCP/IP line listed, refer to “Appendix
F: Installing the TCP/IP Protocol” or your Ethernet adapter’s user guide to
install TCP/IP now.) Click the Properties button.
To do this, you need to configure your PC’s network settings to obtain an IP (or
TCP/IP) address automatically (called DHCP). Computers use IP addresses to
communicate with each other across a network or the Internet.
Find out which operating system your computer is running, such as Windows
95, 98, Millennium, NT 4.0, 2000, or XP. You will need to know which oper-
ating system your computer is running. You can find out by clicking the Start
button and then going to the Settings option. Then click Control Panel, and
then double-click the System icon. If your Start menu doesn’t have a Settings
option, you’re running Windows XP. Click the Cancel button when done.
You may need to do this for each computer you are connecting to the Router.
Important: These instructions apply only to Windows 95,
Windows 98, Windows Millennium, Windows 2000, or Windows
XP machines. For TCP/IP setup under Windows NT, see your
Windows manual. By default Windows 98, 2000, Me, and XP has
TCP/IP installed and set to obtain an IP address automatically.
The next few pages tell you, step by step, how to configure your network set-
tings based on the type of Windows operating system you are using. Make sure
that an Ethernet card or adapter has been successfully installed in each PC you
will configure. Once you’ve configured your computers, continue to “Chapter
6: Configure the Router.”
Figure 5-1
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. Click the IP Address tab and select Obtain an IP address automatically,
Configuring Windows 2000 PCs
as shown in Figure 5-2.
1. Go to the Network screen by clicking the Start button. Click Settings and
then Control Panel. From there, double-click the Network and Dial-up
Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Double-click the Local
Area Connection. (See Figure 5-3.) Click the Properties button.
Figure 5-2
4. Now click the Gateway tab to ensure that the Installed Gateway field is left
blank. Click the OK button.
5. Click the OK button again. Windows may ask you for the original
Windows installation disk or additional files. Supply them by pointing to
the
correct
file
location,
e.g.,
D:\win98,
D:\win9x,
Figure 5-3
c:\windows\options\cabs, etc. (if “D” is the letter of your CD-ROM drive).
6. Windows may ask you to restart your PC. Click the Yes button. If Windows
does not ask you to restart, restart your computer anyway.
Go to “Chapter 6: Configure the Router.”
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. Select Internet Protocol (TCP/IP), shown in Figure 5-4, and click the
Configuring Windows XP PCs
Properties button.
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions for
Windows 2000.
1. Click to the Network screen by clicking the Start button and then Control
Panel. From there, click the Network and Internet Connections icon and
then the Network Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Double-click the Local
Area Connection. (See Figure 5-6.) Click the Properties button.
Figure 5-4
4. Select Obtain an IP address automatically in both places, as shown in
Figure 5-5, and click the OK button. Click the OK button again to complete
the PC configuration.
Figure 5-6
Figure 5-5
5. Restart your computer.
Go to “Chapter 6: Configure the Router.”
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. Select Internet Protocol (TCP/IP), as shown in Figure 5-7, and click the
Chapter 6: Configure the Router
Properties button.
This chapter will show you how to configure the Router to function in your net-
work and gain access to the Internet through your Internet Service Provider
(ISP). Detailed description of the Router’s Web-based Utility can be found in
“Chapter 7: The Cable/DSL Firewall Router’s Web-based Utility.” Your ISP
may require the use of a Host Name and Domain Name. Further, you will set
the WAN Connection Type on the Router’s Setup tab based on the information
provided by your ISP. You will need the setup information from your ISP. If you
do not have this information, please contact your ISP before proceeding.
The instructions from your ISP will tell you how to set up your PC for Internet
access. Because you are now using the Router to share Internet access among
several computers, you will use the setup information to configure the Router
instead of your PC. You only need to configure the Router once using the first
computer you set up.
Figure 5-7
4. Select Obtain an IP address automatically. Once the new window Select
Obtain an IP address automatically in both places, as shown in Figure 5-
8, and click the OK button. Click the OK button again to complete the PC
configuration.
1. Open your web browser. (It
is all right if you get an error
message at this point.
Figure 6-1
Continue following these
shown in Figure 6-1. Press the Enter key.
2. An Enter Network Password window, shown in Figure 6-2, will appear
(Windows XP users will see a Connect to 192.168.1.1 window, shown in
Figure 6-3). Windows XP, the screen may look different.) Leave the User
Name field empty, and enter admin in lowercase letters in the Password
field (admin is the default password). Then, click the OK button.
Figure 5-8
5. Restart your computer.
Go to “Chapter 6: Configure the Router.”
Figure 6-2
Figure 6-3
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. The Router configuration screen will appear with the Setup tab selected.
Based on the setup instructions from your ISP, you may need to provide the
following information.
Obtain an IP Address Automatically
If your ISP says that you are
connecting through DHCP or a
dynamic IP address from your
ISP, perform these steps:
Host Name and Domain Name: These fields allow you to provide a host
name and domain name for the Router. These fields are usually left blank.
If requested by your ISP (usually cable ISPs), complete these two fields.
A. S e l e c t O b t a i n a n I P
Automatically as the WAN
Connection Type. (Shown in
Figure 6-4.)
Device IP Address and Subnet Mask: The values for the Router’s IP
Address and Subnet Mask are shown on the Setup screen. The default value
is 192.168.1.1 for the IP Address and 255.255.255.0 for the Subnet Mask.
Leave these settings alone.
B. Click the Apply and Continue
Figure 6-4
4. The Router supports six connection types: Obtain an IP Address
Automatically, Static IP Address, PPPoE, RAS, PPTP, and HBS. These
types are listed in the drop-down menu for the WAN Connection Type set-
ting. Each Setup screen and available features will differ depending on what
kind of connection type you select. Proceed to the instructions for the con-
nection type you are using. When you are finished with the Setup tab, pro-
ceed to step 5.
buttons to save the setting, or
click the Cancel button to clear the setting and start over. When you are finished,
then proceed to step 5.
Static IP Address
If your ISP says that you are
connecting through a static or
fixed IP address from your ISP,
perform these steps:
IMPORTANT: If you have previously enabled any Internet-sharing
proxy server software on any of your PCs, you must disable it now.
Some examples of Internet-sharing software are Internet LanBridge,
Wingate, ICS, and Sygate. To disable your Internet-sharing software:
A. Select Static IP as the WAN
Connection Type. (Shown in
Figure 6-5.)
•
•
If you are running Netscape Navigator, click Edit >> Preferences
>> Advanced >> Proxies. Click Direct Connection to the
Internet.
If you are running Internet Explorer 5.x or higher, click Start >>
Settings >> Control Panel >> Internet Options >> Connections
>> LAN Settings. Remove checkmarks from all three boxes.
Click the OK button to continue.
B. Enter the IP Address.
C. Enter the Subnet Mask.
D. Enter the Gateway Address.
Figure 6-5
Also, you must disable any Internet log-on software (such as Ivasion
Winpoet or Enternet 300) and any firewall software (such as
ZoneAlarm and Watchdog) on all of your PCs.
E. Enter the DNS in the 1, 2,
and/or 3 fields. You need to enter at least one DNS address.
F. Click the Apply and Continue buttons to save the settings, or click the Cancel
button to clear the settings and start over. When you are finished, then proceed
to step 5.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
PPPoE
PPTP
If your DSL provider says that
you are connecting through
PPPoE or if you normally enter
a user name and password to
access the Internet, perform
these steps:
PPTP is a service used in Europe
only. (Shown in Figure 6-8.) If
you are using a PPTP connec-
tion, check with your ISP for the
necessary setup information.
When you are finished with the
Setup tab, proceed to step 5.
A. Select PPPoE as the WAN
Connection Type. (Shown in
Figure 6-6.)
B. Enter the User Name.
Figure 6-6
C. Enter the Password.
Figure 6-8
D. Click the Apply and Continue buttons to save the settings, or click the Cancel
button to clear the settings and start over.
E. When you are finished, click the Status tab, and then click the Connect
button to start the connection. Proceed to step 5.
HBS
RAS
HBS is a service used in
Australia only. (Shown in Figure
6-9.) If you are using a HBS
connection, check with your ISP
for the necessary setup informa-
tion.
RAS is a service used in
Singapore only. (Shown in
Figure 6-7.) If you are using a
RAS connection, check with
your ISP for the necessary setup
information.
When you are finished with the
Setup tab, proceed to step 5.
When you are finished with the
Setup tab, proceed to step 5.
Figure 6-9
Figure 6-7
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Chapter 7: The Cable/DSL Firewall
Router’s Web-based Utility
Overview
5. If you haven’t already done so, click the Apply button and then the
Continue button to save your Setup settings. Close the web browser.
6. Reset the power on your cable or DSL modem.
7. Restart your computers so that they can obtain the Router’s new settings.
If you need advanced setting information, please refer to “Chapter 7: The
Cable/DSL Firewall Router’s Web-based Utility” or the Linksys support
website at support.linksys.com.
For your convenience, use the Router’s web-based utility to administer it. This
chapter will explain all of the functions in this utility. The utility can be
accessed via Microsoft Internet Explorer or Netscape Navigator through use of
a computer connected with an Ethernet cable to the Router.
Congratulations! You’ve suc-
cessfully configured the
For a basic Router setup, most users only have to use the following screens of
the utility:
Router. Test the setup by
opening your web browser
Figure 6-10
Figure 6-10.
• Setup Enter the settings provided by your ISP.
• Password The Router’s default password is admin. To secure the Router,
change the Password from its default.
If you are unable to reach our website, you may want to review what you
did in this section or refer to “Appendix A: Troubleshooting.”
The Status, Firewall, VPN, Password, Status, DHCP, Log, and Help tabs are
also available for basic setup of the Router. For advanced setup of the Router,
click the Advanced tab to access these screens: Filters, Forwarding, Dynamic
Routing, Static Routing, DMZ Host, and MAC Address Clone.
Proceed to “Chapter 7: The Cable/DSL Firewall Router’s Web-based
Utility” for more details and advanced settings information.
Quick and Easy Router Administration
To access the web-based utility of the Router, launch Internet Explorer or
Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in
the Address field, as shown in Figure 7-1. Then, press Enter.
Figure 7-1
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
An Enter Network Password window, shown in Figure 7-2, will appear
(Windows XP users will see a Connect to 192.168.1.1 window, shown in Figure
7-3). Leave the User Name field blank, and enter admin in the Password field.
Then click the OK button. Router
• Device IP Address and Subnet Mask The values for the Router’s IP
Address and Subnet Mask are shown here. The default values are
192.168.1.1 for the Device IP Address and 255.255.255.0 for the Subnet
Mask.
• WAN Connection Type The Router supports six connection types:
DHCP, PPPoE, Static IP, PPTP, RAS, and HBS. Each Setup screen and
available features will differ depending on what kind of connection type
you select.
Note: You can test and see if the settings are correct by successfully
connecting to the Internet.
Figure 7-2
Figure 7-3
In this section, you’ll find brief descriptions of each web page in the Utility and
each page’s key functions.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
Setup
The Setup screen is the first screen you see when you access the web-based
utility. If you have already installed and set up the Router, you have already
seen this screen and properly configured all of the screen’s values.
• Host Name & Domain Name These fields allow you to supply a host
and domain name for the Router. Some ISPs require these names as iden-
tification. You may have to check with your ISP to see if your broadband
Internet service has been configured with a host and domain name. In
most cases, leaving these fields blank will work.
Figure 7-4
Obtain an IP Address Automatically
By default, the Router’s WAN Connection Type is set to obtain an IP address
automatically, shown in Figure 7-4, and it should be used only if your ISP sup-
ports DHCP.
• Firmware Version This entry shows the version and date of the firmware
you are using. Future versions of the Router’s firmware will be posted and
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
• Time Zone Set your local time zone here.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Static IP
PPPoE
If you are
required to use
a permanent IP
address, then
select Static
IP, as shown in
Figure 7-5.
Some
ISPs use PPPoE
( Po i n t - t o - Po i n t
DSL-based
Protocol
over
Ethernet) to establish
Internet connections
for end-users. If you
are connected to the
Internet through a
DSL line, check with
your ISP to see if
they use PPPoE. If
they do, select the
PPPoE connection
type, as shown in
Figure 7-6.
Figure 7-6
Figure 7-5
User Name and Password Enter the User Name and Password provided by
your ISP.
Specify WAN IP Address This is the IP address that the Router has, when seen
from the WAN, or the Internet. Your ISP will provide you with the IP Address
you need to specify here.
Connect on Demand and Max Idle Time You can configure the Router to cut
your connection with your ISP after a specified period of time (Max Idle Time).
If you have been disconnected due to inactivity, Connect on Demand enables
the Router to automatically re-establish your connection as soon as you attempt
to access the Internet again. If you wish to activate Connect on Demand, click
the radio button. In the Max Idle Time field, enter the number of minutes you
want to have elapsed before your Internet access disconnects.
Subnet Mask This is the Router’s Subnet Mask, as seen by external users on
the Internet (including your ISP). Your ISP will provide you with the Subnet
Mask.
Default Gateway Address Your ISP will provide you with the Default Gateway
Address.
Keep Alive Option and Redial Period If you select this option, the Router will
periodically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option,
click the radio button next to Keep Alive. The default Redial Period is 30 sec-
onds.
DNS (Required) Your ISP will provide you with at least one DNS (Domain
Name System) Server IP Address.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
Important: For DSL users, if you need to enable PPPoE support,
choose PPPoE. If you do enable PPPoE, remember to remove any
PPPoE applications that are already installed on any of your PCs.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
RAS
PPTP
Point
to
Point
Remote
Access
Tunneling Protocol
(PPTP) is a service
that applies to connec-
tions in Europe only.
Figure 7-8 shows a
PPTP setup.
Service (RAS) is a
service that applies to
connections
Singapore
in
only
(shown in Figure 7-
7). For users in
Singapore,
check
with Singtel for
information on RAS.
Specify
WAN IP
Address This is the IP
address that the
Router has, when seen
from the WAN, or the
Internet. Your ISP will
provide you with the
IP Address you need
to specify here.
Figure 7-7
Figure 7-8
User Name and Password Enter the User Name and Password supplied by
Singtel.
Subnet Mask This is the Router’s Subnet Mask, as seen by external users on the
Internet (including your ISP). Your ISP will provide you with the Subnet Mask.
RAS Plan Select the type of plan you have.
Connect on Demand and Max Idle Time You can configure the Router to cut
your connection with your ISP after a specified period of time (Max Idle Time).
If you have been disconnected due to inactivity, Connect on Demand enables
the Router to automatically re-establish your connection as soon as you attempt
to access the Internet again. If you wish to activate Connect on Demand, click
the radio button. In the Max Idle Time field, enter the number of minutes you
want to have elapsed before your Internet access disconnects.
Default Gateway Address Your ISP will provide you with the Default Gateway
Address.
Connect on Demand and Max Idle Time You can configure the Router to cut
your connection with your ISP after a specified period of time (Max Idle Time).
If you have been disconnected due to inactivity, Connect on Demand enables the
Router to automatically re-establish your connection as soon as you attempt to
access the Internet again. If you wish to activate Connect on Demand, click the
radio button. In the Max Idle Time field, enter the number of minutes you want
to have elapsed before your Internet access disconnects.
Keep Alive Option and Redial Period If you select this option, the Router will
periodically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option,
click the radio button next to Keep Alive. The default Redial Period is 30 sec-
onds.
Keep Alive Option and Redial Period If you select this option, the Router will
periodically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option, click
the radio button next to Keep Alive. The default Redial Period is 30 seconds.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any page,
click the Cancel button.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
HBS
Firewall
The
HeartBeat
Signal (HBS) is
service that
a
applies to connec-
tions in Australia
only. (Shown in
Figure 7-9.) For
users in Australia,
check with your ISP
for setup informa-
tion.
Figure 7-9
User Name and Password Enter the User Name and Password supplied by
your ISP.
Heart Beat Server Enter the IP address of the Heart Beat Server. This is sup-
plied by your ISP.
Connect on Demand and Max Idle Time You can configure the Router to cut
your connection with your ISP after a specified period of time (Max Idle Time).
If you have been disconnected due to inactivity, Connect on Demand enables
the Router to automatically re-establish your connection as soon as you attempt
to access the Internet again. If you wish to activate Connect on Demand, click
the radio button. In the Max Idle Time field, enter the number of minutes you
want to have elapsed before your Internet access disconnects.
Figure 7-10
The Firewall Tab, shown in Figure 7-10, allows you to set the Cable/DSL
Firewall Router’s level of security. Some environments require greater security
while some Internet applications work better with fewer restrictions. This tab
allows you to customize these settings.
Keep Alive Option and Redial Period If you select this option, the Router will
periodically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option,
click the radio button next to Keep Alive. The default Redial Period is 30 sec-
onds.
Advanced Firewall Protection Enable this option to employ SPI (Stateful
Packet Inspection) and DoS (Denial of Service). These functions allow for
more detailed review of data packets entering your network environment and
prevention of Denial of Service attacks.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Web Filter You can either enable or disable these four filtering methods by
PPTP Pass Through
selecting Allow or Deny.
•
Point-to-Point Tunneling Protocol Pass Through is the method used to
enable VPN sessions to a Windows NT 4.0 or 2000 server. PPTP Pass
Through is enabled by default. To disable this feature, click on Disable next
to PPTP Pass Through, and then the Apply button. Click the Continue
button.
• Proxy If local users have access to WAN proxy servers, they may be able
to circumvent the Router’s content filters and access Internet sites
blocked by the Router. Denying Proxy will block access to any WAN
proxy servers.
PPPoE Pass Through
• Java Java is a programming language for websites. If you deny Java, you
run the risk of not having access to Internet sites created using this pro-
gramming language.
•
PPPoE Pass Through allows your PC(s) to use the PPPoE client software
provided by your ISP. Some ISPs may request that you use this feature on
the Router. PPPoE Pass Through is enabled by default. To disable PPPoE
Pass Through, click on Disable and then the Apply button. Click the
Continue button.
• ActiveX ActiveX is a programming language for websites. If you deny
ActiveX, you run the risk of not having access to Internet sites created
using this programming language.
Remote Management
•
This feature allows you to manage the Router from a remote location, via
the Internet. To enable this feature, click on Enable, and enter the port
number you want to use when accessing the Router remotely. Click the
Apply button and then the Continue button. Remote Management must be
activated before you can manage the Router from a remote location. If you
wish to use this feature on the browser, enter http:\\<WAN IP Address>:
port. (Enter your specific WAN IP Address in place of <WAN IP
Address>, and enter the port number in place of the word port.)
To disable Remote Management, click on Disable, and click the Apply but-
ton. Then click the Continue button.
• Cookie A cookie is data stored on your PC and used by Internet sites
when you interact with them, so you may not want to deny cookies.
Block WAN Request
•
By enabling the Block WAN Request feature, you can prevent your network
from being “pinged,” or detected, by other Internet users. The Block WAN
Request feature also reinforces your network security by hiding your net-
work ports. Both functions of the Block WAN Request feature make it more
difficult for outside users to access your network. This feature is enabled by
default. Select Disable to disable this feature. Then click the Apply button
and then the Continue button to save your changes.
•
Remote Upgrade
•
This feature allows you to upgrade the Router’s firmware from a remote
location. To enable Remote Upgrade, click on Enable, and then click the
Apply button. Then click the Continue button. Remote Management must
be activated before you can manage the Router from a remote location.
Multicast Pass Through
•
IP Multicasting occurs when a single data transmission is sent to multiple
recipients at the same time. Using this feature, the Router allows IP multi-
cast packets to be forwarded to the appropriate computers. Select Enable to
support the feature, or Disable to disable it.
MTU (Maximum Transmission Unit)
•
This feature specifies the largest packet size permitted for network trans-
mission. Select Auto to leave the MTU at its factory default value. Select
Manual to enable the MTU value you enter in the Size field. It is recom-
mended that you keep this value in the 1200 to 1500 range. For most DSL
users, it is recommended to use the value 1492.
IPSec Pass Through
•
Internet Protocol Security (IPSec) is a suite of protocols used to implement
secure exchange of packets at the IP layer. To allow IPSec tunnels to pass
through the Router, IPSec Pass Through is enabled by default. To disable
IPSec Pass Through, click on Disable and then the Apply button. Click the
Continue button.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any page,
click the Cancel button. For further help on this tab, click the Help button.
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Virtual Private Networking (VPN) is a security measure that basically creates
a secure connection between two remote locations. This connection is very
specific as far as its settings are concerned; this is what creates the security.
The VPN screen, shown in Figure 7-11, allows you to configure your VPN set-
tings to make your network more secure.
VPN
Note: Network security, while a desirable and often necessary
aspect of networking, is complex and requires a thorough under-
standing of networking principles.
Establishing a Tunnel
The Firewall Router creates a tunnel or channel between two endpoints, so that
the data or information between these endpoints is secure. To establish this tun-
nel, select the tunnel you wish to create in the (Select Tunnel Entry) drop-
down box. It is possible to create up to two simultaneous tunnels.
Then check the box next to Enable to enable the tunnel.
Once the tunnel is enabled, enter the name of the tunnel in the Tunnel Name
field. This is to allow you to identify multiple tunnels and does not have to
match the name used at the other end of the tunnel.
Click the Delete This Tunnel button to delete any tunnel entry. Click the
Summary button to view information about the selected tunnel, after the tun-
nel has been connected.
Figure 7-11
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Local Secure Group and Remote Secure Group
• IP Address - If you select IP Address, only the computer with the spe-
cific IP Address that you enter will be able to access the tunnel. In the
example shown in Figure 7-13, only the computer with IP Address
192.168.1.10 can access the tunnel from this end. Only the computer with
IP Address 192.168.2.12 can access the tunnel from the remote end (in
your settings, use the IP Addresses appropriate for your VPN).
The Local Secure Group is the computer(s) on your LAN that can access the
tunnel. The Remote Secure Group is the computer (s) on the remote end of the
tunnel that can access the tunnel. Under Local Secure Group and Remote
Secure Group, you may choose one of three options: Subnet, IP Address, and
IP Range. Under Remote Secure Group, you have two additional options: Host
and Any.
Note: The IP Addresses and Subnet Mask values used here are for
example only. Do not try to use them for your actual setup. Obtain
the relevant information from your own network to accurately config-
ure your Firewall Router.
• Subnet - If you select Subnet (which is the default), this will allow all
computers on the local subnet to access the tunnel. In the example shown
in Figure 7-12, all Local Secure Group computers with IP Addresses
192.168.1.xxx will be able to access the tunnel. All Remote Secure Group
computers with IP Addresses 192.168.2.xxx will be able to access the tun-
nel (in your settings, use the IP Addresses appropriate for your VPN).
When using the Subnet setting, the default values of 0 should remain in
the last fields of the IP and Mask settings.
Figure 7-13
• IP Range - If you select IP Range, it will be a combination of Subnet and
IP Address. You can specify a range of IP Addresses within the Subnet
which will have access to the tunnel. In the example shown in Figure 7-
14, all computers on this end of the tunnel with IP Addresses between
192.168.1.1 and 192.168.1.20 can access the tunnel from the local end.
Only computers assigned an IP Address between 192.168.2.1 and
192.168.2.100 can access the tunnel from the remote end (in your set-
tings, use the IP Ranges appropriate for your VPN).
Figure 7-12
Note: It is possible to set up your Firewall Router using any combi-
nation of the three settings under Local Secure Group and the five set-
tings under Remote Secure Group. For instance, when Subnet is cho-
sen on the local end of the tunnel, Subnet does not have to be chosen
at the remote end. So a single IP Address could be chosen to access
the tunnel on the local end and a range of IP Addresses could be set at
the remote end of the tunnel.
Figure 7-14
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Under Remote Secure Group, you have two additional options: Host and Any.
Remote Security Gateway
• Host - If you select Host for the Remote Secure Group, then the Remote
Secure Group will be the same as the Remote Security Gateway setting:
IP Address, FQDN (Fully Qualified Domain Name), or Any. (Remote
Security Gateway settings are explained on the following page.) In the
example shown in Figure 7-15, the Remote Secure Group is the same as
the Remote Security Gateway, set to a specific IP Address.
The Remote Security Gateway is the VPN device, such as a second Firewall
Router, on the remote end of the VPN tunnel. Under Remote Security
Gateway, you have three options: IP Address, FQDN, and Any.
• IP Address - If you select IP Address, as shown in Figure 7-17, enter the
IP Address of the VPN device at the other end of the tunnel. The remote
VPN device can be another Firewall Router, a VPN Server, or a comput-
er with VPN client software that supports IPSec. The IP Address may
either be static (permanent) or dynamic (changing), depending on the set-
tings of the remote VPN device. Make sure that you have entered the IP
Address correctly, or the connection cannot be made. Remember, this is
NOT the IP Address of the local Firewall Router, but the IP Address of the
remote Firewall Router or device with which you wish to communicate.
Figure 7-15
• Any - If you select Any for the Remote Security Group, as shown in
Figure 7-16, the local Firewall Router will accept a request from any IP
address. This setting should be chosen when the other endpoint is using
DHCP or PPPoE on the WAN side.
Figure 7-17
• FQDN (Fully Qualified Domain Name) - If you select FQDN, as shown
in Figure 7-18, enter the FQDN of the VPN device at the other end of the
tunnel. The remote VPN device can be another Firewall Router, a VPN
Server, or a computer with VPN client software that supports IPSec. The
FQDN is the host name and domain name for a specific computer on the
Internet, for example, vpn.myvpnserver.com.
Figure 7-16
Figure 7-18
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
• Any - If you select Any for the Remote Security Gateway, as shown in
Figure 7-19, the VPN device at the other end of the tunnel will accept a
request from any IP address. The remote VPN device can be another
Firewall Router, a VPN Server, or a computer with VPN client software
that supports IPSec. If the remote user has an unknown or dynamic IP
address (such as a professional on the road or a telecommuter using
DHCP or PPPoE), then Any should be selected.
Key Management
In order for any encryption to occur, the two ends of the tunnel must agree on
the type of encryption and the way the data will be decrypted. This is done by
sharing a “key” to the encryption code. Under Key Management, you may
choose automatic or manual key management.
Automatic Key Management
Select Auto (IKE) and enter a series of numbers or letters in the Pre-shared Key
field. Check the box next to PFS (Perfect Forward Secrecy) to ensure that the
initial key exchange and IKE proposals are secure. In the example shown in
Figure 7-20, the word MyTest is used. Based on this word, which MUST be
entered at both ends of the tunnel if this method is used, a key is generated to
scramble (encrypt) the data being transmitted over the tunnel, where it is
unscrambled (decrypted). You may use any combination of up to 24 numbers or
letters in this field. No special characters or spaces are allowed. In the Key
Lifetime field, you may optionally select to have the key expire at the end of a
time period of your choosing. Enter the number of seconds you’d like the key to
be useful, or leave it blank for the key to last indefinitely.
Figure 7-19
Encryption
Using Encryption also helps make your connection more secure. There are
two different types of encryption: DES or 3DES (3DES is recommended
because it is more secure). You may choose either of these, but it must be the
same type of encryption that is being used by the VPN device at the other end
of the tunnel. Or, you may choose not to encrypt by selecting Disable.
Authentication
Figure 7-20
Authentication acts as another level of security. There are two types of authen-
tication: MD5 and SHA (SHA is recommended because it is more secure). As
with encryption, either of these may be selected, provided that the VPN device
at the other end of the tunnel is using the same type of authentication. Or, both
ends of the tunnel may choose to Disable authentication.
Manual Key Management
Similarly, you may choose Manual keying, which allows you to generate the
key yourself. Enter your key into the Encryption KEY field. Then enter an
Authentication KEY into that field. These fields must both match the infor-
mation that is being entered in the fields at the other end of the tunnel. The
example in Figure 7-21 shows some sample entries for both the Encryption and
Authentication Key fields. Up to 24 alphanumeric characters are allowed to
create the Encryption Key. Up to 20 alphanumeric characters are allowed to
create the Authentication Key.
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
The Inbound SPI and Outbound SPI fields are different, however. The
Inbound SPI value set here must match the Outbound SPI value at the other end
of the tunnel. The Outbound SPI here must match the Inbound SPI value at the
other end of the tunnel. In the example (see Figure7-21), the Inbound SPI and
Outbound SPI values shown would be opposite on the other end of the tunnel.
Only numbers can be used in these fields. After you click the Apply button,
hexadecimal characters (series of letters and numbers) are displayed in the
Inbound SPI and Outbound SPI fields.
Figure 7-21
Once you are satisfied with all your settings, click the Apply button. If you
make any mistakes, clicking the Cancel button will exit the screen without sav-
ing any changes, provided that you have not already clicked the Apply button.
After the VPN device is set up at the other end of the tunnel, you may click the
Connect button to use the tunnel. This assumes that both ends of the tunnel
have a physical connection to each other (e.g., over the Internet, physical
wiring, etc.). After clicking the Connect button, click the Summary button. If
the connection is made, the screen shown in Figure 7-22 will appear:
Figure 7-23
On the VPN screen, the word Connected should appear beside Status if the
connection is successful. The other fields reflect the information that you
entered on the VPN screen to make the connection.
If Disconnected appears under Status, as shown in Figure 7-23, some problem
exists that prevents the creation of the tunnel. Make sure that all of your wiring
is securely connected. Double-check all the values you entered on the VPN
screen to make sure they are correct. If the other end of the tunnel is some dis-
tance from you (e.g., in another city, etc.), call to make sure that the settings on
that end of the tunnel are correct as well.
Figure 7-22
If, for any reason, you experience a temporary disconnection, the connection will
be re-established as long as the settings on both ends of the tunnel stay the same.
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
To get more details concerning your tunnel connection, click the View Logs
button. The screen in Figure 7-24 will appear:
Figure 7-24
Select the log you wish to view: All (to view all logs), System Log, Access Log,
Firewall Log, or VPN Log. The System Log screen displays a list of cold and
warm starts, web login successes and failures, and packet filtering policies. The
Access Log shows all incoming and outgoing traffic. The Firewall Log lists
activities performed by the firewall to prevent DoS attacks, including URL fil-
tering and time filtering. The VPN Log screen displays successful connections,
transmissions and receptions, and the types of encryption used.
Once you no longer have need of the tunnel, simply click the Disconnect but-
ton on the bottom of the VPN page.
To change advanced settings, select the tunnel whose advanced settings you
wish to change. Then, click the Advanced Setting button to change the
Advanced Settings for a specific VPN tunnel.
Figure 7-25
Encryption
Advanced Settings for Selected IPSec Tunnel
Select the length of the key used to encrypt/decrypt ESP packets. There are two
choices: DES and 3DES. 3DES is recommended because it is more secure.
From the Advanced Settings screen, shown in Figure 7-25, you can adjust the
settings for specific VPN tunnels.
Authentication
Select the method used to authenticate ESP packets. There are two choices:
MD5 and SHA. SHA is recommended because it is more secure.
Phase 1
Phase 1 is used to create a security association (SA), often called the IKE SA.
After Phase 1 is completed, Phase 2 is used to create one or more IPSec SAs,
which are then used to key IPSec sessions.
Group
There are two Diffie-Hellman Groups to choose from: 768-bit and 1024-bit.
Diffie-Hellman refers to a cryptographic technique that uses public and private
keys for encryption and decryption.
Operation Mode
There are two modes: Main and Aggressive, and they exchange the same IKE
payloads in different sequences. Main mode is more common; however, some
people prefer Aggressive mode because it is faster. Main mode is for normal
usage and includes more authentication requirements than Aggressive mode.
Main mode is recommended because it is more secure. No matter which mode
is selected, the VPN Router will accept both Main and Aggressive requests
from the remote VPN device.
Key Lifetime
In the Key Lifetime field, you may optionally select to have the key expire at the
end of a time period of your choosing. Enter the number of seconds you’d like
the key to be used until a re-key negotiation between each endpoint is completed.
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Phase 2
Password
Group
There are two Diffie-Hellman Groups to choose from: 768-bit and 1024-bit.
Diffie-Hellman refers to a cryptographic technique that uses public and private
keys for encryption and decryption.
Key Lifetime
In the Key Lifetime field, you may optionally select to have the key expire at the
end of a time period of your choosing. Enter the number of seconds you’d like
the key to be used until a re-key negotiation between each endpoint is completed.
Other Settings
NetBIOS broadcast
Check the box next to NetBIOS broadcast to enable NetBIOS traffic to pass
through the VPN tunnel.
Anti-replay
Check the box next to Anti-replay to enable the Anti-replay protection. This
feature keeps track of sequence numbers as packets arrive, ensuring security at
the IP packet-level.
Figure 7-26
Keep-Alive
The Password screen, shown in Figure 7-26, allows you to change the password,
set SNMP Community names, enable UPnP Services, and restore default set-
tings on the Router.
Check the box next to Keep-Alive to re-establish the VPN tunnel connection
whenever it is dropped. Once the tunnel is initialized, this feature will keep the
tunnel connected for the specified amount of idle time.
Router Password It is strongly recommended that you set a password for the
Router. The default password is admin. If you don’t change the password, all
users on your network will be able to access the Router using the default pass-
word admin.
Unauthorized IP Blocking
Check this box to block unauthorized IP addresses. Complete the on-screen
sentence to specify how many times IKE must fail before blocking that unau-
thorized IP address for a length of time that you specify (in seconds).
SNMP Community Each SNMP Community field allows a name to be
assigned to any SNMP community that has been set up in the network. Four
different communities can be defined, including the two default communities,
public and private. For each SNMP Community name, you can configure each
community’s accessibility, making it either Read-Only or Read-Write.
Restore Factory Defaults If you select the Restore Factory Defaults option
and click the Apply button, you will clear all of the Router’s settings.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Do not restore the factory defaults unless you are having difficulties with the
Router and have exhausted all other troubleshooting measures. Once the Router
is reset, you will have to re-enter all of your configuration data.
Status
UPnP Function Universal Plug and Play (UPnP) allows Windows XP to auto-
matically configure the Router for various Internet applications, such as gam-
ing and videoconferencing. To enable the use of UPnP, click the Yes radio but-
ton next to UPnP Function, or click the No radio button to disable the use of
UPnP.
UPnP Control This feature allows Windows XP to read and write UPnP
Forwarding using UPnP. To enable this feature, click the Yes radio button next
to UPnP Control, or click the No radio button to disable this feature. If dis-
abled, UPnP Forwarding can only be read.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
Figure 7-27
The Status screen, shown in Figure 7-27, displays the Router’s current status
and reflects the data and selections you’ve entered using the Setup screen.
Note: The information provided and buttons available may
vary depending on the Router’s settings.
All of the information provided on this screen is read-only. To make changes,
select the Setup tab.
Host Name This field shows the name of the Router. This entry is necessary
for some ISPs.
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Firmware Version This field shows the installed version and date of the
firmware. Version dates are slightly more accurate than version numbers.
DHCP
Current Time Based upon the time zone selection made on the Setup tab, this
field will display the current time.
Login This indicates if you are using a dial-up style connection like PPPoE,
RAS, PPTP, or HBS. For PPPoE, RAS, PPTP, or HBS only, there is a Connect
button to click if you are disconnected and want to re-establish a connection.
LAN These fields display the current IP Address and Subnet Mask of the
Router, as seen by users on your local area network. The DHCP Server field
shows the status of the Router’s DHCP server function, which is either enabled
or disabled.
WAN These fields display the WAN IP Address, WAN Subnet Mask, and
WAN Default Gateway IP Address of the Router, as seen by external users on
the Internet. The DNS (Domain Name System) IP Address fields show the IP
address(es) of the DNS currently used by the Router. Multiple DNS IP settings
are common. In most cases, the first available DNS entry is used.
DHCP Release Click the DHCP Release button to release the current IP
address of the device connected to the Router’s WAN port.
Figure 7-28
DHCP Renew Click the DHCP Renew button to replace the current IP
address—of the device connected to the Router’s WAN port—with a new IP
address.
From the DHCP screen, shown in Figure 7-28, you can configure the Router as
a DHCP Server.
DHCP Clients Table Click the DHCP Clients Table button to view the list of
PCs that were given IP addresses by the Router.
A Dynamic Host Configuration Protocol (DHCP) server automatically assigns
an IP address to each PC on your network for you. Unless you already have one,
it is highly recommended that you leave the Router enabled as a DHCP server.
DHCP Server DHCP is already enabled by factory default. If you already
have a DHCP server on your network, set the Router’s DHCP option to
Disable. Click the Apply button and then the Continue button. If you disable
DHCP, remember to assign a static IP address to the Router.
Starting IP Address Enter a value for the DHCP server to start with when
issuing IP addresses. This value must be 192.168.1.2 or greater, because the
default IP address for the Router is 192.168.1.1.
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Number of DHCP Users (Optional) Enter the maximum number of PCs that
you want the DHCP server to assign IP addresses to. This number cannot be
greater than 253. In order to determine the DHCP IP Address range, add the
starting IP address (e.g., 100) to the number of DHCP users. By default, as
shown in Figure 7-28, add 100 to 50, and the range is 192.168.1.100 to
192.168.1.149.
Log
Client Lease Time The Client Lease Time is the amount of time a network
user will be allowed connection to the Router with their current dynamic IP
address. Enter the amount of time, in minutes, that the user will be “leased” this
dynamic IP address.
DNS The Domain Name System (DNS) is how the Internet translates domain
or website names into Internet addresses or URLs. Your ISP will provide you
with at least one DNS Server IP Address. If you wish to use another, type that
IP Address in one of these fields. You can type up to three DNS Server IP
Addresses here. The Router will use these for quicker access to functioning
DNS servers. Otherwise, leave this blank.
Figure 7-29
WINS The Windows Internet Naming Service (WINS) manages each PC’s
interaction with the Internet. If you use a WINS server, enter that server’s IP
Address here. Otherwise, leave this blank.
The Log tab, shown in Figure 7-29, provides you with a log of all incoming and
outgoing URLs or IP addresses for your Internet connection.
DHCP Clients Table Click the DHCP Clients Table button to show the cur-
rent DHCP Client data. (This data is stored in temporary memory and changes
periodically.)
To access activity logs, select the Enable option next to Log. This function can
be disabled by clicking the Disable radio button.
With logging enabled, you can choose to view temporary logs or have a per-
manent record, using the Logviewer software. Temporary logs can be accessed
from the Log screen by clicking either the Incoming Access Log or Outgoing
Access Log button. The Incoming Access Log gives you a log of all the incom-
ing Internet traffic while the Outgoing Access Log lists all the URLs and IP
addresses of Internet sites that users on your network have accessed.
To apply any of the settings you change on a page, click the Apply button, and
then click the Continue button. To cancel any values you’ve entered on any
page, click the Cancel button.
For a permanent record of these logs, Logviewer software must be used. This
Logviewer saves all incoming and outgoing activity as a permanent file on your
PC’s hard drive. In the Send Log to field, enter the fixed IP address of the PC
running the Logviewer software. The Router will now send updated logs to that
PC.
Click the View Logs button for a selection of logs to view (see Figure 7-30).
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Help
Figure 7-30
From the drop-down menu, select the log you wish to view: All (to view all
logs), System Log, Access Log, Firewall Log, or VPN Log.
• System Log The System Log screen displays a list of cold and warm
starts, web login successes and failures, and packet filtering policies.
• Access Log The Access Log screen shows all incoming and outgoing
traffic.
Figure 7-31
• Firewall Log The Firewall Log screen lists activities performed by the
firewall to prevent DoS attacks, including URL filtering and time filtering.
Under the Help tab, shown in Figure 7-31, you’ll find links to all of the Utility’s
internal support documentation, including the application that upgrades the
Router’s firmware.
• VPN Log The VPN Log screen displays successful connections, trans-
missions and receptions, and the types of encryption used.
Clicking on any of the topics in the bar on the left will give you help informa-
tion about that topic.
To clear a log, click the Clear button. To refresh a log, click the Refresh but-
ton. To return to the Log screen, close this window.
Clicking the Linksys Website link will take you to Linksys’s website,
www.linksys.com, provided you are connected to the Internet.
To clear any values you’ve entered on any page, click Cancel and re-enter
information. To apply any settings you’ve altered on any page, click the Apply
button. Once all settings are correct, click Continue.
Clicking the Online manual in PDF format link will take you to the latest ver-
sion of the user guide for this Router. The guide will be in Adobe Acrobat
Portable Document File (.pdf) format. You will need the Adobe Acrobat Reader
to view this pdf. If you do not have the Acrobat Reader, click the Adobe
Website link to download it.
for free. If the Router can access the Internet already, there’s no need to down-
load a newer firmware version, unless that version has a new feature that you
want to use. Loading new firmware onto the Router does not always enhance
the speed or the quality of your connection.
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
To upgrade the Router’s firmware:
Filters
Note: By upgrading the Router’s firmware, you may lose the Router’s
configuration settings.
1. Select the Help tab (see Figure 7-31).
2. Click Upgrade Firmware to display the window shown in Figure 7-32.
3. Click the Browse but-
ton to find the
firmware upgrade file
that you downloaded
from the Linksys
website and then
extracted.
Figure 7-32
4. Double-click the firmware file you downloaded and extracted. Click the
Upgrade button, and follow the instructions there.
Advanced
The following tabs are for advanced users or users whose setup needs require
special configuration. When you click the Advanced tab, you will be able to set
up these features. There are six additional tabs available.
•
•
•
Filters - Allows you to block or allow specific kinds of Internet usage.
Forwarding - Sets up public services on your network.
Dynamic Routing - Sets up the Router so it will automatically adjust to
physical changes in the network’s layout.
Figure 7-33
•
•
•
Static Routing - Sets up static routes as needed when network information
must travel to a specific host or network.
DMZ Host - Allows one local user to be exposed to the Internet for use of
special-purpose services such as online gaming or videoconferencing.
MAC Address Cloning - Allows you to “clone” your Ethernet adapter’s
MAC address onto the Router.
The Filters screen, shown in Figure 7-33, allows you to block or allow specific
kinds of Internet usage.You can set up Internet access policies for specific PCs.
Internet Access Policy Multiple filters can be saved as Internet Access
Policies. To create or edit a Policy, select the number of the Policy from the
drop-down menu. The screen will change to reflect the settings of this Policy.
If you want to delete this Policy, click the Delete button.
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
To see a summary of all Policies, click the Summary button.
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Figure 7-35
5. To block websites with specific URL addresses, enter each URL address in
a Website Blocking by URL Address field. You can enter up to four URL
addresses.
Figure 7-34
The Policies are listed on this screen with their names and settings (see Figure
7-34). To update the Internet Policy Summary screen with the most recent infor-
mation, click the refresh button. To delete any Policy from this screen, check
the empty box beneath the Delete button, and then click the Delete button. To
return to the Filters screen, click the Close button.
6. To block websites that use specific keywords as part of their URL address-
es, enter each keyword in a Website Blocking by Keyword field. You can
enter up to six keywords.
7. Select the service(s) you want to block. The default setting is Disable.
Default services include FTP, Telnet, SMTP, DNS, TFTP, HTTP, POP3,
NNTP, SNMP, and Ping. To add a service or edit a service’s settings, follow
these instructions:
Enter Policy Name Policies are created using the settings on the Filters
screen. To create a policy:
1. Enter a Policy Name in the field provided.
a. Click the Add Service
button (see Figure 7-
36). You can have up to
60 services, including
default services such as
FTP and Telnet.
2. Select whether you want to Allow or Deny Internet access for the PCs you
will list on the List of PCs screen, during the days and hours you will select.
3. Select the appropriate Days and Time during which you want Internet
access to be filtered.
4. Click the Edit List of PCs button. The List of PCs screen will appear (see
Figure 7-35). All PCs is selected by default. Enter the IP address or MAC
address of any PC to which this Policy will apply. You can enter a range of
IP addresses to select multiple PCs. Click the Apply button to save your
settings. Click the Cancel button to undo any changes. Click the Close but-
ton to return to the Filters screen.
Figure 7-36
62
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
b. To create a new service, enter the name of the service in the Service Name
field. To edit a service’s settings, select the service from the box on the
right of the screen.
Forwarding
c. From the Protocol drop-down menu, select the protocol type for this serv-
ice, such as TCP, UDP, or ICMP.
d. In the Port Range fields, enter the range of ports for this service.
e. To add a service, click the Add button. To edit the settings for a service,
click the Modify button.
f. To delete a service, select the service from the box on the right of the
screen. Click the Delete button.
g. Click the Apply button to save your changes. Click the Cancel button to
undo your changes. Click the X in the upper righthand corner of the
screen to close the Add Service window.
8. To save your settings for an Internet Access Policy, click the Apply button
on the Filters screen. To undo your changes, click the Cancel button on the
Filters screen.
Figure 7-37
From the Forwarding tab, shown in Figure 7-37, you can set up public services
on your network, such as web servers, ftp servers, e-mail servers, or other spe-
cialized Internet applications. (Specialized Internet applications are any appli-
cations that use Internet access to perform functions such as videoconferencing
or online gaming. Some Internet applications may not require any forwarding.)
When users send this type of request to your network via the Internet, the
Router will forward those requests to the appropriate PC. Before using
Forwarding, the Router’s DHCP function must be disabled under the DHCP tab
and the computer must be assigned a new static LAN IP address because the IP
address may change when using the DHCP server.
64
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
If you need to forward all ports to one PC, see the “DMZ Host” section.
•
Telnet A terminal
emulation protocol
commonly used on
To add a server using Forwarding:
Internet
and
1. Enter the name of the application in the appropriate Customized
TCP/IP-based net-
works. It allows a
user at a terminal or
computer to log
Applications field.
2. Next to the name of the application, enter the number or range of the exter-
nal port(s) used by the server or Internet application in the Ext. Port col-
umn. Check with the Internet application software documentation for more
information.
onto
a
remote
device and run a
program.
3. On the same line, select the protocol UDP or TCP, or select both protocols.
•
SM T P (Simple
Mail
Transfer
4. Enter the IP address of the server that you want the Internet users to be able
to access. To find the IP address, go to “Appendix G: Finding the MAC
Address and IP Address for Your Ethernet Adapter.”
Protocol) The stan-
dard e-mail proto-
col on the Internet.
It is a TCP/IP pro-
tocol that defines
the message format
5. Check the Enable box to enable the services you have defined. Port Range
Forwarding will not function if the Enable button is left unchecked. This is
disabled (unchecked) by default.
Figure 7-38
and the message transfer agent (MTA), which stores and forwards the mail.
6. Configure as many entries as needed—the Router supports up to ten ranges
•
DNS (Domain Name System) The way that Internet domain names are
located and translated into IP addresses. A domain name is a meaningful
and easy-to-remember “handle” for an Internet address.
of ports. Click the Apply button and Continue button when you are done.
UPnP Forwarding
•
•
TFTP (Trivial File Transfer Protocol) A version of the TCP/IP FTP proto-
col that has no directory or password capability.
The UPnP Forwarding screen, shown in Figure 7-38, displays preset applica-
tion settings as well as options for customization of port services for other
applications.
Finger A UNIX command widely used on the Internet to find out infor-
mation about a particular user, such as a telephone number, whether the
user is currently logged on, and the last time the user was logged on. The
person being “fingered” must have placed his or her profile on the system
in order for the information to be available. Fingering requires entering the
full user@domain address.
The Preset Applications are among the most widely used Internet applications.
They include the following:
•
FTP (File Transfer Protocol) A protocol used to transfer files over a
TCP/IP network (Internet, UNIX, etc.). For example, after developing the
HTML pages for a website on a local machine, they are typically uploaded
to the web server using FTP. FTP includes functions to log onto the net-
work, list directories, and copy files. FTP operations can be performed by
typing commands at a command prompt or via an FTP utility running under
a graphical interface such as Windows. FTP transfers can also be initiated
from within a web browser by entering the URL preceded by ftp://.
66
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
•
•
HTTP (HyperText Transport Protocol) The communications protocol used
to connect to servers on the World Wide Web. Its primary function is to
establish a connection with a web server and transmit HTML pages to the
client web browser.
5. Enter the IP address of the server that you want the Internet users to be able
to access. To find the IP address, go to “Appendix G: Finding the MAC
Address and IP Address for Your Ethernet Adapter.”
6. Check the Enable box to enable the services you have defined. UPnP
Forwarding will not function if the Enable button is left unchecked. This is
disabled (unchecked) by default.
POP3 (Post Office Protocol 3) A standard mail server commonly used on
the Internet. It provides a message store that holds incoming e-mail until
users log on and download it. POP3 is a simple system with little selectivi-
ty. All pending messages and attachments are downloaded at the same time.
POP3 uses the SMTP messaging protocol.
Port Triggering
•
•
NNTP (Network News Transfer Protocol) The protocol used to connect to
Usenet groups on the Internet. Usenet newsreaders support the NNTP pro-
tocol.
SNMP (Simple Network Management Protocol) A widely used network
monitoring and control protocol. Data is passed from SNMP agents, which
are hardware and/or software processes reporting activity in each network
device (hub, router, bridge, etc.) to the workstation console used to oversee
the network. The agents return information contained in a MIB
(Management Information Base), which is a data structure that defines
what is obtainable from the device and what can be controlled (turned off,
on, etc.).
Figure 7-39
You must check the Enable box to enable the applications you have defined.
From the Forwarding screen, click the Port Triggering button to open the Port
Triggering screen, shown in Figure 7-39. From here, you can set the Router to
watch outgoing data on assigned port numbers. The IP address of the comput-
er that sends the matching data is remembered by the Router, so that when the
requested data returns through the Router, the data is pulled back to the proper
computer by way of IP address and port mapping rules.
To add a server using UPnP Forwarding:
1. Enter the name of the application in the appropriate Application Name
field.
2. Next to the name of the application, enter the number of the external port
used by the server in the Ext. Port column. Check with the Internet appli-
cation software documentation for more information.
1. Enter the Application Name of the trigger.
2. Enter the Trigger Port Range used by the application. Check with the
Internet application for the port number needed.
3. On the same line, select the protocol UDP or TCP.
3. Enter the Incoming Port Range used by the application. Check with the
4. Enter the number of the internal port used by the server in the Int. Port col-
umn. Check with the Internet application software documentation for more
information.
Internet application for the port number needed.
4. Click the Apply button and then click the Continue button.
68
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Dynamic Routing
Static Routing
Figure 7-40
From the Dynamic Routing screen, shown on Figure 7-40, you can enable the
Router to automatically adjust to physical changes in the network’s layout. The
Router, using the RIP protocol, determines the network packets’ route based on
the fewest number of hops between the source and the destination. The RIP pro-
tocol regularly broadcasts routing information to other routers on the network.
To set up Dynamic Routing:
Figure 7-41
If the Router is connected to more than one network, it may be necessary to set
up a static route between them. This can be done from the Static Routing
screen, shown in Figure 7-41. A static route is a pre-determined pathway that
network information must travel to reach a specific host or network. From the
Static Routing tab, click the Show Routing Table button to view the current
static routing configuration.
1. Choose the correct Working Mode. Gateway Mode should be used if the
Router is hosting your network’s connection to the Internet. Router Mode
should be selected if the Router exists on a network with other routers. In
Router Mode, any computer connected to the Router will not be able to con-
nect to the Internet unless you have another router function as the Gateway.
To create a static route entry:
2. Choose a Dynamic Routing path protocol for either transmission (TX) or
1. Select a Static Route Entry from the drop-down list. The Router supports
reception (RX) of network data.
up to 20 static route entries.
Click the Show Routing Table button to open a chart displaying how data is
routed through your LAN.
To delete a Static Routing entry, select an entry, and click the Delete this
entry button.
When finished making your changes on this tab, click the Apply button fol-
lowed by the Continue button to save these changes, or click the Cancel but-
ton to undo your changes. For further help on this tab, click the Help button.
70
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
2. Enter the following data to create a new static route.
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
DMZ Host
Destination LAN IP: The Destination LAN IP is the address of the remote
network or host to which you want to assign a static route. Enter the IP
address of the host for which you wish to create a static route here. If you
are building a route to an entire network, be sure that the network portion
of the IP address is set to 0. For example, the Router’s standard IP address
is 192.168.1.1. Based on this address, the address of the routed network is
192.168.1, with the last digit determining the Router’s place on the network.
Therefore you would enter the IP address 192.168.1.0 if you wanted to
route to the Router’s entire network, rather than just to the Router.
Subnet Mask: The Subnet Mask (also known as the Network Mask) deter-
mines which portion of an IP address is the network portion, and which por-
tion is the host portion. Take, for example, a network in which the Subnet
Mask is 255.255.255.0. This determines (by using the values 255) that the
first three numbers of a network IP address identify this particular network,
while the last digit (from 1 to 254) identifies the specific host.
Default Gateway: This IP address should be the IP address of the gateway
device that allows for contact between the Router and the remote network
or host.
Hop Count: This determines the maximum number of steps between net-
work nodes that data packets will travel. A node is any device on the net-
work, such as PCs, print servers, routers, etc.
Figure 7-42
From the DMZ Host tab, shown in Figure 7-42, you can set Port 4/DMZ to
DMZ or LAN connection. Any user on the Internet can access incoming or out-
going data from the DMZ host without the use of firewall protection. This fea-
ture is used for special-purpose services such as Internet gaming and video-
conferencing. Port 4 is the only port used for DMZ, and only one computer can
be in DMZ mode.
interface: Select LAN or WAN, depending on the location of the static
route’s final destination.
3. When finished making your changes on this tab, click the Apply button and
then the Continue button to save these changes, or click the Cancel button
to undo your changes.
DMZ Port
To enable or disable the DMZ port, click the Enable radio button or Disable
radio button.
DMZ Host Address
Assigned by the DMZ Port: The DMZ host is the first PC connected to
Port 4/DMZ of the Router, either directly or through a hub or switch. The
Router will only allow one PC to be the DMZ host.
72
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Specify an IP Address behind the DMZ Port: If you have multiple PCs
connected to Port 4/DMZ via a hub or switch, you can specify which PC is
the DMZ host. To expose a computer with a specific IP address, enter that
computer’s IP address in this field. To get the IP address of a computer,
refer to “Appendix G: Finding the MAC Address and IP Address for Your
Ethernet Adapter.”
MAC Address Clone
Specify a MAC Address behind the DMZ Port: If you have multiple PCs
connected to Port 4/DMZ via a hub or switch, you can specify which PC is
the DMZ host. To expose a PC with a specific MAC address, enter that
computer’s MAC address in this field. To get the MAC address of a com-
puter, refer to “Appendix G: Finding the MAC Address and IP Address for
Your Ethernet Adapter.”
Click the PCs behind DMZ Port button to view all computers connected on
Port 4/DMZ (multiple computers can be connected via a hub or switch).
Current DMZ Host
Figure 7-43
The IP address of the current DMZ host is displayed here.
From the MAC Address Clone screen, shown in Figure 7-43, you can change
the Router’s WAN Mac Address.
When finished, click the Apply button and click the Continue button to save
the settings. Otherwise, click the Cancel button to undo changes made on this
screen.
The Router’s MAC address is a 12-digit code assigned to a unique piece of
hardware for identification, like a social security number. If your ISP requires
MAC address registration, find your adapter’s MAC address by following the
instructions in “Appendix G: Finding the MAC Address and IP Address for
Your Ethernet Adapter.”
To define a MAC address for the WAN port, click the first radio button next to
User Defined WAN MAC Address, and enter the 12 digits of your adapter’s
MAC address in the on-screen fields. This “clones” your network adapter’s
MAC address onto the Router, so you do NOT have to call your ISP to change
the registered MAC address to the Router’s MAC address.
If you want to clone the MAC address of the PC you are CURRENTLY using
to configure the Router, then click the second radio button. The Router will
automatically detect your PC’s MAC address. It is recommended that the PC
registered with the ISP is used to open the MAC Address Clone page.
When finished making your changes on this screen, click the Apply button and
then the Continue button to save these changes, or click the Cancel button to
undo your changes.
74
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
DynDNS.org
DDNS
Figure 7-44
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS
lets you assign a fixed host and domain name to a dynamic Internet IP address.
It is useful when you are hosting your own website, FTP server, or other serv-
er behind the Router.
Figure 7-45
To order DynDNS service, click the appropriate link at the top of the DDNS
screen.
Before you can use this feature, you need to sign up for DDNS service at one
of two DDNS service providers, DynDNS.org or TZO.
Username, Password, and Host Name Enter the Username, Password, and
Host Name of the account you set up with DynDNS.org.
DDNS Service The DDNS feature is disabled by default. To enable this fea-
ture, select your DDNS service provider, DynDNS.org or TZO.com, from the
drop-down menu.
Internet IP Address The Router’s current Internet IP Address is displayed
here. Because it is dynamic, this will change.
Status The status of the DDNS service connection is displayed here.
The features available on the DDNS screen will vary, depending on which
DDNS service provider you use.
When finished making your changes on this screen, click the Apply button and
then the Continue button to save these changes, or click the Cancel button to
undo your changes.
76
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
TZO.com
Appendix A: Troubleshooting
Common Problems and Solutions
This appendix consists of two parts: “Common Problems and Solutions” and
“Frequently Asked Questions.” Provided are possible solutions to problems
regarding the installation and operation of the Router. If your situation is
described here, the problem should be solved by applying the corresponding
solution. If you can’t find an answer here, check the Linksys website at
1. I need to set a static IP address on a PC.
The Router, by default, assigns an IP address range of 192.168.1.100 to
192.168.1.150 using the DHCP server on the Router. To set a static IP address,
you can only use the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to
192.168.1.254. Each PC or network device that uses TCP/IP must have a
unique address to identify itself in a network. If the IP address is not unique to
a network, Windows will generate an IP conflict error message. You can assign
a static IP address to a PC by performing the following steps:
Figure 7-46
For Windows 95, 98, and Me:
To sign up for a free, 30-day trial of TZO service, order TZO service, or man-
age your TZO service, click the appropriate link at the top of the DDNS screen.
A. Click Start, Settings, and Control Panel. Double-click Network.
B. In The following network components are installed box, select the TCP/IP->
associated with your Ethernet adapter. If you only have one Ethernet adapter
installed, you will only see one TCP/IP line with no association to an Ethernet
adapter. Highlight it and click the Properties button.
C. In the TCP/IP properties window, select the IP address tab, and select
Specify an IP address. Enter a unique IP address that is not used by any
other computer on the network connected to the Router. You can only use
an IP address in the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151
to 192.168.1.254. Make sure that each IP address is unique for each PC or
network device.
Domain Name, Email Address, and TZO Password Key Enter the Domain
Name, Email Address, and TZO Password Key of the service you set up with
TZO.
Internet IP Address The Router’s current Internet IP Address is displayed
here. Because it is dynamic, this will change.
Status The status of the DDNS service connection is displayed here.
D. Click the Gateway tab, and in the New Gateway prompt, enter 192.168.1.1,
which is the default IP address of the Router. Click the Add button to accept
the entry.
E. Click the DNS tab, and make sure the DNS Enabled option is selected.
Enter the Host and Domain names (e.g., John for Host and home for
Domain). Enter the DNS entry provided by your ISP. If your ISP has not
provided the DNS IP address, contact your ISP to get that information or go
to its website for the information.
When finished making your changes on this screen, click the Apply button and
then the Continue button to save these changes, or click the Cancel button to
undo your changes.
F. Click the OK button in the TCP/IP properties window, and click Close or
the OK button for the Network window.
G. Restart the computer when asked.
78
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
For Windows 2000:
For Windows XP:
A. Click Start, Settings, and Control Panel. Double-click Network and
Dial-Up Connections.
B. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions for
Windows 2000.
C. In the Components checked are used by this connection box, highlight
Internet Protocol (TCP/IP), and click the Properties button. Select Use
the following IP address option.
D. Enter a unique IP address that is not used by any other computer on the
network connected to the Router. You can only use an IP address in the
ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254.
E. Enter the Subnet Mask, 255.255.255.0.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS
server (provided by your ISP). Contact your ISP or go on its website to find
the information.
A. Click Start and Control Panel.
B. Click the Network and Internet Connections icon and then the Network
Connections icon.
C. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
D. In the This connection uses the following items box, highlight Internet
Protocol (TCP/IP). Click the Properties button.
E. Click the use the following IP address radio button. Enter a unique IP
address that is not used by any other computer on the network connected
to the Router. You can only use an IP address in the ranges 192.168.1.2 to
192.168.1.99 and 192.168.1.151 to 192.168.1.254.
H. Click the OK button in the Internet Protocol (TCP/IP) Properties window,
and click the OK button in the Local Area Connection Properties window.
I. Restart the computer if asked.
F. Enter the Subnet Mask, 255.255.255.0.
G. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
H. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS
server (provided by your ISP). Contact your ISP or go on its website to find
the information.
For Windows NT 4.0:
A. Click Start, Settings, and Control Panel. Double-click the Network icon.
B. Click the Protocol tab, and double-click TCP/IP Protocol.
C. When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter.
I. Click the OK button in the Internet Protocol (TCP/IP) Properties window.
Click the OK button in the Local Area Connection Properties window.
2. I want to test my Internet connection.
D. Select Specify an IP address, and enter a unique IP address that is not
used by any other computer on the network connected to the Router. You
can only use an IP address in the ranges 192.168.1.2 to 192.168.1.99 and
192.168.1.151 to 192.168.1.254.
A. Check your TCP/IP settings.
For Windows 95, 98, and Me:
• Refer to “Appendix F: Installing the TCP/IP Protocol” and “Chapter 5:
Configure the PCs” for details. Make sure Obtain IP address automati-
cally is selected in the settings.
E. Enter the Subnet Mask, 255.255.255.0.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Click the DNS tab, and enter the Host and Domain names (e.g., John for
Host and home for Domain). Under DNS Service Search Order, click the
Add button. Enter the DNS IP address in the DNS Server field, and click
the Add button. Repeat this action for all DNS IP addresses given by your
ISP.
H. Click the OK button in the TCP/IP Protocol Properties window, and click
the Close button in the Network window.
I. Restart the computer if asked.
For Windows 2000:
• Click Start, Settings, and Control Panel. Double-click Network and
Dial-Up Connections.
• Right-click the Local Area Connection that is associated with the
Ethernet adapter you are using, and select the Properties option.
• In the Components checked are used by this connection box, highlight
Internet Protocol (TCP/IP), and click the Properties button. Make sure
80
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
that Obtain an IP address automatically and Obtain DNS server
address automatically are selected.
• Click the OK button in the Internet Protocol (TCP/IP) Properties win-
dow, and click the OK button in the Local Area Connection Properties
window.
C. In the command prompt, type ping 192.168.1.1 and press the Enter key.
• If you get a reply, the computer is communicating with the Router.
• If you do NOT get a reply, please check the cable, and make sure Obtain
an IP address automatically is selected in the TCP/IP settings for your
Ethernet adapter.
• Restart the computer if asked.
D. In the command prompt, type ping followed by your WAN IP address and
press the Enter key. The WAN IP Address can be found in the web inter-
face of the Router. For example, if your WAN IP address is 1.2.3.4, you
would enter ping 1.2.3.4 and press the Enter key.
For Windows XP:
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons
and menus look like previous Windows versions), please follow the
instructions for Windows 2000.
• If you get a reply, the computer is connected to the Router.
• If you do NOT get a reply, try the ping command from a different comput-
er to verify that your original computer is not the cause of the problem.
• Click Start and Control Panel.
• Click the Network and Internet Connections icon and then the
Network Connections icon.
E. In the command prompt, type ping www.yahoo.com and press the Enter
key.
• Right-click the Local Area Connection that is associated with the
Ethernet adapter you are using, and select the Properties option.
• In the This connection uses the following items box, highlight Internet
Protocol (TCP/IP), and click the Properties button. Make sure that
Obtain an IP address automatically and Obtain DNS server address
automatically are selected.
• If you get a reply, the computer is connected to the Internet. If you cannot
open a webpage, try the ping command from a different computer to ver-
ify that your original computer is not the cause of the problem.
• If you do NOT get a reply, there may be a problem with the connection.
Try the ping command from a different computer to verify that your orig-
inal computer is not the cause of the problem.
• Click the OK button in the Internet Protocol (TCP/IP) Properties win-
dow, and click the OK button in the Local Area Connection Properties
window.
3. I am not getting an IP address on the WAN with my Internet connection.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
you have connectivity.
• Restart the computer if asked.
B. If you need to register the MAC address of your Ethernet adapter with your
ISP, please see “Appendix G: Finding the MAC address and IP Address for
Your Ethernet Adapter.” If you need to clone the MAC address of your
Ethernet adapter onto the Router, see the MAC Address Clone section of
“Chapter 7: The Cable/DSL Firewall Router’s Web-based Utility” for
details.
C. Make sure you are using the right WAN settings. Contact your ISP to see if
your WAN connection type is DHCP, Static IP Address, or PPPoE (com-
monly used by DSL consumers). Please refer to the Setup section of
“Chapter 7: The Cable/DSL Firewall Router’s Web-based Utility” for
details on WAN settings.
For Windows NT 4.0:
• Click Start, Settings, and Control Panel. Double-click the Network
icon.
• Click the Protocol tab, and double-click on TCP/IP Protocol.
• When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter and set it for Obtain an IP address
from a DHCP server.
• Click the OK button in the TCP/IP Protocol Properties window, and click
the Close button in the Network window.
• Restart the computer if asked.
D. Make sure you have the right cable. Check to see if the WAN column has a
solidly lit Link LED.
B. Open a command prompt.
• For Windows 95, 98, and Me, please click Start and Run. In the Open
field, type in command. Press the Enter key or click the OK button.
• For Windows NT, 2000, and XP, please click Start and Run. In the Open
field, type cmd. Press the Enter key or click the OK button.
E. Make sure the cable connecting from your cable or DSL modem is con-
nected to the Router’s WAN port. Verify that the Status page of the Router’s
web interface shows a valid IP address from your ISP.
82
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds,
and then turn on the Router, cable/DSL modem, and computer. Check the
Status tab of the Router’s web-based utility to see if you get an IP address.
Your VPN may require port 500/UDP packets to be passed to the computer that
is connecting to the IPSec server. Refer to “Problem #7, I need to set up online
game hosting or use other Internet applications” for details.
4. I am not able to access the Router’s web interface Setup page.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
your computer is properly connected to the Router.
6. I need to set up a server behind my Router.
B. Refer to “Appendix G: Finding the MAC Address and IP address for Your
Ethernet Adapter” to verify that your computer has an IP Address, Subnet
Mask, Gateway, and DNS.
C. Set a static IP address on your system; refer to “Problem #1: I need to set a
static IP address.”
To use a server like a web, ftp, or mail server, you need to know the respective
port numbers they are using. For example, port 80 (HTTP) is used for web;
port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110
(POP3 incoming) are used for the mail server. You can get more information
by viewing the documentation provided with the server you installed. Follow
these steps to set up port forwarding through the Router’s web-based utility. We
will be setting up web, ftp, and mail servers.
D. Refer to “Problem #10: I need to remove the proxy settings or the dial-up
pop-up window (for PPPoE users).”
5. I can’t get my Virtual Private Network (VPN) Pass-Through working through the
Router (not a VPN tunnel).
address of the Router, and go to the Advanced => Filter tab. Make sure you
have IPsec pass-through and/or PPTP pass-through enabled.
IP address of the Router. Go to the Advanced => Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the Ext. Port range of the service you are using. For example, if you
have a web server, you would enter the range 80 to 80.
D. Check the protocol you will be using, TCP and/or UDP.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix G: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
VPNs that use IPSec with the ESP (Encapsulation Security Payload known as
protocol 50) authentication will work fine. At least one IPSec session will work
through the Router; however, simultaneous IPSec sessions may be possible,
depending on the specifics of your VPNs.
VPNs that use IPSec and AH (Authentication Header known as protocol 51)
are incompatible with the Router. AH has limitations due to occasional incom-
patibility with the NAT standard.
F. Check the Enable option for the port services you want to use. Consider the
example below:
Customized
Application
Web server
FTP server
SMTP (outgoing) 25 to 25
POP3 (incoming) 110 to 110
Ext. Port
TCP
UDP
X
IP Address
Enable
Change the IP address for the Router to another subnet to avoid a conflict
between the VPN IP address and your local IP address. For example, if your
VPN server assigns an IP address 192.168.1.X (X is a number from 1 to 254)
and your local LAN IP address is 192.168.1.X (X is the same number used in
the VPN IP address), the Router will have difficulties routing information to
the right location. If you change the Router’s IP address to 192.168.2.1, that
should solve the problem. Change the Router’s IP address through the Setup tab
of the web interface. If you assigned a static IP address to any computer or net-
work device on the network, you need to change its IP address accordingly to
192.168.2.Y (Y being any number from 1 to 254). Note that each IP address
must be unique within the network.
80 to 80
21 to 21
X
X
X
X
192.168.1.100
192.168.1.101
192.168.1.102
192.168.1.102
X
X
X
X
X
X
When you have completed the configuration, click the Apply button and then
the Continue button.
84
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
7. I need to set up online game hosting or use other Internet applications.
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
8. I can’t get the Internet game, server, or application to work.
If you want to play online games or use Internet applications, most will work
without doing any port forwarding or DMZ hosting. There may be cases when
you want to host an online game or Internet application. This would require
you to set up the Router to deliver incoming packets or data to a specific com-
puter. This also applies to the Internet applications you are using. The best way
to get the information on what port services to use is to go to the website of the
online game or application you want to use. Follow these steps to set up online
game hosting or use a certain Internet application:
If you are having difficulties getting any Internet game, server, or application
to function properly, consider exposing one PC to the Internet using
DeMilitarized Zone (DMZ) hosting. This option is available when an applica-
tion requires too many ports or when you are not sure which port services to
use. Make sure you disable all the forwarding entries if you want to success-
fully use DMZ hosting, since forwarding has priority over DMZ hosting. (In
other words, data that enters the Router will be checked first by the forwarding
settings. If the port number that the data enters from does not have port for-
warding, then the Router will send the data to whichever PC or network device
you set for DMZ hosting.) Follow these steps to set DMZ hosting:
address of the Router. Go to the Advanced => Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the Ext. Port range of the service you are using. For example, if you
want to host Unreal Tournament (UT), you would enter the range 7777 to
27900.
IP address of the Router. Go to the Advanced => Forwarding tab.
B. Disable or remove the entries you have entered for forwarding. Keep this
information in case you want to use it at a later time.
D. Check the protocol you will be using, TCP and/or UDP.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix G: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
C. Click the DMZ Host tab.
D. Enter the Ethernet adapter’s IP address of the computer you want exposed
to the Internet. This will bypass the NAT firewall for that computer. Please
refer to “Appendix G: Finding the MAC Address and IP Address for Your
Ethernet Adapter” for details on getting an IP address.
F. Check the Enable option for the port services you want to use. Consider the
example below:
Once completed with the configuration, click the Apply button and then the
Continue button.
Customized
Application
UT
Halflife
PC Anywhere
VPN IPSEC
Ext. Port
TCP
X
UDP
IP Address
Enable
9. I forgot my password, or the password prompt always appears when saving
settings to the Router.
Reset the Router to factory default by pressing the Reset button for 30 seconds
and then releasing it. If you are still getting prompted for a password when sav-
ing settings, then perform the following steps:
7777 to 27900
X
X
X
X
192.168.1.100
192.168.1.105
192.168.1.102
192.168.1.100
X
X
X
X
27015 to 27015 X
5631 to 5631
500 to 500
address of the Router. Enter the default password admin, and click the
Password tab.
When you have completed the configuration, click the Apply button and then
the Continue button.
B. Enter a different password in the Router Password field, and enter the
same password in the second field to confirm the password.
C. Click the Apply and Continue buttons.
86
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
10. I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-
up window.
13. The firmware upgrade failed, and/or the Diag LED is flashing.
The upgrade could have failed for a number of reasons. Follow these steps to
upgrade the firmware and/or make the Diag LED stop flashing:
If you have proxy settings, you need to disable these on your computer.
Because the Router is the gateway for the Internet connection, the computer
does not need any proxy settings to gain access. Please follow these directions
to verify that you do not have any proxy settings and that the browser you use
is set to connect directly to the LAN.
A. If the firmware upgrade failed, use the TFTP program (it was downloaded
along with the firmware). Open the pdf that was downloaded along with the
firmware and TFTP program, and follow the pdf’s instructions.
B. Set a static IP address on the PC; refer to “Problem #1, I need to set a stat-
ic IP address.” Use the following IP address settings for the computer you
are using:
For Microsoft Internet Explorer 5.0 or higher:
A. Click Start, Settings, and Control Panel. Double-click Internet Options.
B. Click the Connections tab.
IP Address: 192.168.1.50
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
C. Click the LAN settings button and remove anything that is checked.
D. Click the OK button to go back to the previous screen.
E. Click the option Never dial a connection. This will remove any dial-up
pop-ups for PPPoE users.
C. Perform the upgrade using the TFTP program or the Router’s web-based
utility through its Help tab.
For Netscape 4.7 or higher:
A. Start Netscape Navigator, and click Edit, Preferences, Advanced, and
Proxies.
14. My DSL service’s PPPoE is always disconnecting.
PPPoE is not actually a dedicated or always-on connection. The DSL ISP can
disconnect the service after a period of inactivity, just like a normal phone dial-
up connection to the Internet. There is a setup option to “keep alive” the con-
nection. This may not always work, so you may need to re-establish connec-
tion periodically.
B. Make sure you have Direct connection to the Internet selected on this
screen.
C. Close all the windows to finish.
11. To start over, I need to set the Router to factory default.
Hold the Reset button for up to 30 seconds and then release it. This will return
the password, forwarding, and other settings on the Router to the factory
default settings. In other words, the Router will revert to its original factory
configuration.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. In the Setup tab, select the option Keep Alive, and set the Redial Period
option at 20 (seconds).
12. I need to upgrade the firmware.
D. Click the Apply and Continue buttons.
In order to upgrade the firmware with the latest features, you need to go to the
these steps:
E. Click the Status tab, and click the Connect button.
F. You may see the login status display as Connecting. Press the F5 key to
refresh the screen, until you see the login status display as Connected.
G. Click the Apply and Continue buttons to continue.
latest firmware.
If the connection is lost again, follow steps E to G to re-establish connection.
B. To upgrade the firmware, follow the steps in the Help section found in
“Chapter 7: The Cable/DSL Firewall Router’s Web-based Utility.”
88
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
15. I can't access my email, web, or VPN, or I am getting corrupted data from the
Internet.
The Maximum Transmission Unit (MTU) setting may need to be adjusted. By
default, the MTU is set at 1500. For most DSL users, it is strongly recom-
mended to use MTU 1492. If you are having some difficulties, perform the fol-
lowing steps:
17. The Diag LED stays lit continuously.
The Diag LED lights up when the device is first powered up. Meantime, the
system will boot up itself and check for proper operation. After finishing the
checking procedure, the LED turns off to show that the system is working fine.
If the LED remains lit after this time, the device is not working properly. Try to
flash the firmware by assigning a static IP address to the computer, and then
upgrade the firmware. Try using the following settings, IP Address:
192.168.1.50 and Subnet Mask: 255.255.255.0. To set a static IP address, refer
to “Problem #1: I need to set a static IP address.”
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. Click the Advanced => Filter tab.
D. Look for the MTU option, and select Manual. In the Size field, enter 1492.
E. Click the Apply and Continue buttons to continue.
18. When I enter a URL or IP address, I get a time-out error or am prompted to retry.
• Check if other PCs work. If they do, ensure that your workstation’s IP set-
tings are correct (IP Address, Subnet Mask, Default Gateway, and DNS).
Restart the computer that is having a problem.
If your difficulties continue, change the Size to different values. Try this list of
values, one value at a time, in this order, until your problem is solved:
• If the PCs are configured correctly, but still not working, check the
Router. Ensure that it is connected and ON. Connect to it and check its
settings. (If you cannot connect to it, check the LAN and power connec-
tions.)
• If the Router is configured correctly, check your Internet connection
(DSL/cable modem, etc.) to see if it is working correctly. You can remove
the Router to verify a direct connection.
1462
1400
1362
1300
• Manually configure the TCP/IP with a DNS address provided by your
ISP.
16. I need to use port triggering.
Port triggering looks at the outgoing port services used and will trigger the
Router to open a specific port, depending on which port an Internet application
uses. Follow these steps:
• Make sure that your browser is set to connect directly and that any dial-
up is disabled. For Internet Explorer, click Tools, Internet Options, and
then the Connection tab. Make sure that Internet Explorer is set to Never
dial a connection. For Netscape Navigator, click Edit, Preferences,
Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct
connection to the Internet.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. Click theAdvanced => Forwarding tab, and click the Port Triggering but-
ton.
19. The Full/Col LED keeps flickering continuously.
• Check the Category 5 Ethernet cable and its RJ-45 connectors.
• There may be interference with other network devices. Try removing
other PCs or network devices to see if the problem persists. Eliminate
each network device one at a time to determine the cause.
D. Enter any name you want to use for the Application Name.
E. Enter the Triggered Port Range. Check with your Internet application
provider for more information on which outgoing port services it is using.
F. Enter the Incoming Port Range. Check with your Internet Application
provider for more information on which incoming port services are
required by the Internet application.
90
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
I set up an Unreal Tournament Server, but others on the LAN cannot join. What do
I need to do? If you have a dedicated Unreal Tournament server running, you
need to create a static IP for each of the LAN computers and forward ports
7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You
can also use a port forwarding range of 7777 ~ 27900. If you want to use the
UT Server Admin, forward another port (8080 usually works well but is used
for remote admin. You may have to disable this.), and then in the
[UWeb.WebServer] section of the server.ini file, set the ListenPort to 8080 (to
match the mapped port above) and ServerName to the IP assigned to the
Router from your ISP.
Frequently Asked Questions
What is the maximum number of IP addresses that the Router will support? The
Router will support up to 253 IP addresses.
Is IPSec Pass-Through supported by the Router? Yes, it is a built-in feature that
the Router automatically enables.
Where is the Router installed on the network? In a typical environment, the
Router is installed between the cable/DSL modem and the LAN. Plug the
Router into the cable/DSL modem’s Ethernet port.
Can multiple gamers on the LAN get on one game server and play simultaneously
with just one public IP address? It depends on which network game or what
kind of game server you are using. For example, Unreal Tournament supports
multi-login with one public IP.
Does the Router support IPX or AppleTalk? No. TCP/IP is the only protocol stan-
dard for the Internet and has become the global standard for communications.
IPX, a NetWare communications protocol used only to route messages from
one node to another, and AppleTalk, a communications protocol used on
Apple and Macintosh networks, can be used for LAN to LAN connections,
but those protocols cannot connect from WAN to LAN.
How do I get Half-Life: Team Fortress to work with the Router? The default client
port for Half-Life is 27005. The computers on your LAN need to have
“+clientport 2700x” added to the HL shortcut command line; the x would be
6, 7, 8, and on up. This lets multiple computers connect to the same server.
One problem: Version 1.0.1.6 won’t let multiple computers with the same CD
key connect at the same time, even if on the same LAN (not a problem with
1.0.1.3). As far as hosting games, the HL server does not need to be in the
DMZ. Just forward port 27015 to the local IP address of the server comput-
er.
Does the WAN connection of the Router support 100 Mbps Ethernet? Yes, and it
does, of course, support 100 Mbps over the auto-sensing Fast Ethernet 10/100
switch on the LAN side of the Router.
What is Network Address Translation and what is it used for? Network Address
Translation (NAT) translates multiple IP addresses on the private LAN to one
public address that is sent out to the Internet. This adds a level of security
since the address of a PC connected to the private LAN is never transmitted
on the Internet. Furthermore, NAT allows the Router to be used with low cost
Internet accounts, such as DSL or cable modems, when only one TCP/IP
address is provided by the ISP. The user may have many private addresses
behind this single address provided by the ISP.
How can I block corrupted FTP downloads? If you are experiencing corrupted
files when you download a file with your FTP client, try using another FTP
program.
The web page hangs; downloads are corrupt, or nothing but junk characters are
being displayed on the screen. What do I need to do? Force your Ethernet
adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate”
feature of your Ethernet adapter as a temporary measure. (Please look at the
Network Control Panel in your Ethernet adapter’s Advanced Properties tab.)
Make sure that your proxy setting is disabled in the browser. Check our web-
Does the Router support any operating system other than Windows 95, Windows
98, Windows 2000, Windows NT, or Windows XP? Yes, but Linksys does not, at
this time, provide technical support for setup, configuration or troubleshoot-
ing of any non-Windows operating systems.
Does the Router support ICQ send file? Yes, with the following fix: click ICQ
menu -> preference -> connections tab->, and check I am behind a fire-
wall or proxy. Then set the firewall time-out to 80 seconds in the firewall set-
ting. The Internet user can then send a file to a user behind the Router.
If all else fails in the installation, what can I do? Reset the Router by holding
down the reset button until the Diag LED fully turns on and off. Reset your
cable or DSL modem by powering the unit off and then on. Obtain and flash
the latest firmware release that is readily available on the Linksys website,
92
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
How will I be notified of new Router firmware upgrades? All Linksys firmware
can be downloaded for free. The Router’s firmware can be upgraded with
TFTP programs. If the Router’s Internet connection is working well, there is
no need to download a newer firmware version, unless that version contains
new features that you would like to use. Downloading a more current version
of Router firmware will not always enhance the quality or speed of your
Internet connection, and may disrupt your current connection stability.
Does the Router replace a modem? Is there a cable or DSL modem in the Router?
No, this version of the Router must work in conjunction with a cable or DSL
modem.
Which modems are compatible with the Router? The Router is compatible with
virtually any cable or DSL modem that supports Ethernet.
What are the advanced features of the Router? The Router’s advanced features
include Filters, Forwarding, Dynamic Routing, Static Routing, DMZ Hosting,
and MAC Address Cloning.
Will the Router function in a Macintosh environment? Yes, but the Router’s setup
pages are accessible only through Internet Explorer 4.0 or Netscape
Navigator 4.0 or higher for Macintosh.
What is the maximum number of VPN tunnels allowed by the Router?
The Router supports up to two simultaneous IPSec VPN tunnels.
I am not able to get the web configuration screen for the Router. What can I do?
You may have to remove the proxy settings on your Internet browser, e.g.,
Netscape Navigator or Internet Explorer. Or remove the dial-up settings on
your browser. Check with your browser documentation, and make sure that
your browser is set to connect directly and that any dial-up is disabled. Make
sure that your browser is set to connect directly and that any dial-up is dis-
abled. For Internet Explorer, click Tools, Internet Options, and then the
Connection tab. Make sure that Internet Explorer is set to Never dial a con-
nection. For Netscape Navigator, click Edit, Preferences, Advanced, and
Proxy. Make sure that Netscape Navigator is set to Direct connection to the
Internet.
How big is the memory buffer on the Router? 8MB buffer and 2MB flash.
How can I check whether I have static or DHCP IP Addresses? Consult your ISP
to obtain this information.
How do I get mIRC to work with the Router? Under the Port Range Forwarding
tab, set port forwarding to 113 for the PC on which you are using mIRC.
If your questions are not addressed here, refer to the Linksys website,
What is DMZ Hosting? Demilitarized Zone (DMZ) allows one IP address (com-
puter) to be exposed to the Internet. Some applications require multiple
TCP/IP ports to be open. It is recommended that you set your computer with
a static IP if you want to use DMZ Hosting. To get the LAN IP address, see
“Appendix G: Finding the MAC Address and IP Address for Your Ethernet
Adapter,” or use the web-based utility to determine the MAC address of the
computer accessing the Router’s web-based utility.
If DMZ Hosting is used, does the exposed user share the public IP with the Router?
No.
Is the Router cross-platform compatible? Any platform that supports Ethernet
and TCP/IP is compatible with the Router.
How many ports can be simultaneously forwarded? Theoretically, the Router can
establish 520 sessions at the same time, but you can only forward 10 ranges
of ports.
94
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
As secure as the Firewall Router makes your data, there are still more ways to
maximize security. The following are a few suggestions on how to increase data
security beyond the Firewall Router.
Appendix B: Maximizing VPN
Security
1) Maximize security on your other networks. Install firewall routers for your
Internet connections, and use the most up-to-date security measures for
wireless networking.
Just as you maximized your network security with a firewall, you should also
maximize security for your data with the Firewall Router.
2) Narrow the scope of your VPN tunnel as much as possible. Rather than
allowing a range of IP Addresses, use the addresses specific to the end-
points required.
IPSec is compatible with most VPN endpoints and ensures privacy and authen-
tication for data, while authenticating user identification. With IPSec, authen-
tication is based upon the PC's IP Address. This not only confirms the user's
identity but also establishes the secure tunnel at the network layer, protecting
all data that passes through.
3) Do not set the Remote Security Group to Any, as this will open the VPN to
any IP Address. Host a specific IP address.
By operating at the network layer, IPSec is independent of any applications
running on the network. This way, it doesn't harm your PC's performance and
still allows you to do more with greater security. Still, it is important to note
that IPSec encryption does create a slight slowdown in network throughput, due
to encrypting and decrypting data.
4) Maximize encryption and authentication. Use 3DES encryption and SHA
authentication whenever possible.
5) Manage your pre-shared keys. Change pre-shared keys regularly.
Data transmission over the Internet is a hole in network security that is often
overlooked. With VPN maximized, along with the use of a firewall router and
wireless security, you can secure your data even when it leaves your network.
A method of securing data transmission is by using key exchange with a VPN
tunnel. Securing the key exchange without compromising earlier sessions is by
using PFS (Perfect Forward Secrecy). PFS protects by authenticating the key
exchange between two VPN endpoints. This is done by sending one key to the
other endpoint and then then creating a new key to be passed back to the the
original sender of the data exchange.
All of this protection actually comes at a lower cost than most VPN endpoint
software packages. The Firewall Router will allow the users on your network to
secure their data over the Internet without having to purchase the extra client
licenses that other VPN hardware manufacturers and software packages will
require. With VPN functions handled by the router, rather than your PC (which
software packages would require), this frees up your PCs to perform more
functions, more efficiently. An additional benefit is that you aren't required to
reconfigure any of your network PCs.
96
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Note: Keep a record of any changes you make. Those changes will be
identical in the Windows “secpol” application and the Router’s Web-
Based Utility.
Appendix C: Configuring IPSec
between a Windows 2000 or XP PC
Step One: Create an IPSec Policy
and the Firewall Router
1. Click the Start button, select Run, and type secpol.msc in the Open field.
The Local Security Setting screen will appear as shown in Figure C-1.
Introduction
This document demonstrates how to establish a secure IPSec tunnel using pre-
shared keys to join a private network inside the Firewall Router and a Microsoft
Windows 2000 or XP PC. You can find detailed information on configuring the
Microsoft Windows 2000 server at the Microsoft website:
Microsoft KB Q252735 - How to Configure IPSec Tunneling in Windows 2000
Microsoft KB Q257225 - Basic IPSec Troubleshooting in Windows 2000
Environment
The IP addresses and other specifics mentioned in this appendix are for illus-
tration purposes only.
Figure C-1
2. Right-click IP Security Policies on Local Computer, and click Create IP
Security Policy.
Windows 2000 or Windows XP
IP Address: 140.111.1.2 <= User ISP provides IP Address; this is only an
example.
3. Click the Next button, and then enter a name for your policy (for example,
to_router). Then, click Next.
Subnet Mask: 255.255.255.0
4. Deselect the Activate the default response rule check box, and then click
the Next button.
BEFSX41
WAN IP Address: 140.111.1.1 <= User ISP provides IP Address; this is only an
example.
5. Click the Finish button, making sure the Edit check box is checked.
Subnet Mask: 255.255.255.0
LAN IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
98
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. The IP Filter List screen should appear, as shown in Figure C-4. Enter an
appropriate name, such as win->router, for the filter list, and de-select the
Use Add Wizard check box. Then, click the Add button.
Step Two: Build Filter Lists
Filter List 1: win->router
Note: The references
in this section to
“win” are references
to Windows 2000
and XP.
1. In the new policy’s prop-
erties screen, verify that
the Rules tab is selected,
as shown in Figure C-2.
Deselect the Use Add
Wizard check box, and
click the Add button to
create a new rule.
Figure C-4
Figure C-2
4. The Filters Properties
screen will appear, as
shown in Figure C-5.
Select the Addressing
tab. In the Source
address field, select My
IP Address. In the
2. Make sure the IP Filter
List tab is selected, and
click the Add button.
Destination
address
field, select A specific
IP Subnet, and fill in the
IP Address: 192.168.1.0
and
Subnet
mask:
255.255.255.0. (These
are the Router’s default
settings. If you have
changed these settings,
enter your new values.)
Figure C-5
Figure C-3
100
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
5. If you want to enter a description for your filter, click the Description tab
8. The IP Filter List screen should appear, as shown in Figure C-7. Enter an
and enter the description there.
appropriate name, such as router->win for the filter list, and de-select the
Use Add Wizard check box. Click the Add button.
6. Click the OK button. Then, click the OK (for Windows XP) or Close (for
Windows 2000) button on the IP Filter List window.
Filter List 2: router=>win
7. The New Rule Properties screen will appear, as shown in Figure C-6. Select
the IP Filter List tab, and make sure that win -> router is highlighted.
Then, click the Add button.
Figure C-7
9. The Filters Properties
screen will appear, as
shown in Figure C-8.
Select the Addressing
tab. In the Source
address field, select A
specific IP Subnet, and
enter the IP Address:
192.168.1.0 and Subnet
mask: 255.255.255.0.
(Enter your new values if
you have changed the
default settings.) In the
Figure C-6
Destination
address
field, select My IP
Address.
Figure C-8
102
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
10. If you want to enter a description for your filter, click the Description tab
Step Three: Configure Individual Tunnel Rules
and enter the description there.
Tunnel 1: win->router
11. Click the OK button and the New Rule Properties screen should appear
with the IP Filer List tab selected, as shown in Figure C-9. There should
now be a listing for “router -> win” and “win -> router”. Click the OK (for
WinXP) or Close (for Win2000) button on the IP Filter List window.
1. From the IP Filter List
tab, shown in Figure C-
10, click the filter list
win->router.
Figure C-10
2. Click the Filter Action
tab (as in Figure C-11),
and click the filter action
Require Security radio
button. Then, click the
Edit button.
Figure C-9
Figure C-11
104
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. From
the
Security
5. Change the authentica-
tion method to Use this
string to protect the
key exchange (pre-
shared key), as shown
in Figure C-14, and
enter the preshared key
Methods tab, shown in
Figure C-12, verify that
the Negotiate security
option is enabled, and
deselect the Accept
unsecured communica-
tion,
respond using IPSec
check box. Select
but
always
string,
XYZ12345. Click the
OK button.
such
as
Session key Perfect
Forward Secrecy, and
click the OK button.
Figure C-12
Figure C-14
6. This new Preshared
key will be displayed in
Figure C-15. Click the
OK or Close button to
continue.
4. Select the Authentication
Methods tab, shown in
Figure C-13, and click the
Edit button.
Figure C-13
Figure C-15
106
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
7. Select
the
Tunnel
Tunnel 2: router->win
Setting tab, shown in
Figure C-16, and click
The tunnel endpoint is
specified by this IP
Address radio button.
Then, enter the Router’s
WAN IP Address.
9. In the screen, shown in
Figure C-18, make sure
that “win -> router” is
select and deselect the
Use Add Wizard
check box. Then, click
the Add button to cre-
ate the second IP filter.
Figure C-16
Figure C-18
8. Select the Connection
Type tab, as shown in
Figure C-17, and click
All network connec-
tions. Then, click the OK
or Close button to finish
this rule.
10. Go to the IP Filter List
tab, and click the filter
list router->win, as
shown in Figure C-19
Figure C-17
Figure C-19
108
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
11. Click the Filter Action
tab, and select the filter
action Require Security,
as shown in Figure C-20.
Then, click the Edit but-
ton.
13. Change the authenti-
cation method to Use
this string to protect
the key exchange
(preshared key), and
enter the preshared
key string, such as
XYZ12345,
as
shown in Figure C-
22. (This is a sample
key string. Yours
should be a key that
is unique but easy to
remember.)
Then
click the OK button.
Figure C-20
Figure C-22
14. This new Preshared
key will be displayed
in Figure C-23. Click
the OK button to
continue.
12. Click the Authentication
Methods tab, and verify
that the authentication
method Kerberos is
selected, as shown in
Figure C-21. Then, click
the Edit button.
Figure C-21
Figure C-23
110
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
15. From the Tunnel
Setting tab, shown in
Figure C-24, click the
radio button for The
tunnel endpoint is
specified by this IP
Address, and enter
17. From the Rules tab,
shown in Figure C-
26, click the Close
button to return to
the secpol screen.
the
Windows
2000/XP computer’s
IP Address.
Figure C-24
Figure C-26
16. Click the Connection
Type tab, shown in
Figure C-25, and
select All network
connections. Then
click the OK (for
Windows XP) or
Close (for Windows
2000) button to finish.
Step Four: Assign New IPSec Policy
In the IP Security Policies on Local Computer window, shown in Figure C-
27, right-click the policy named to_router, and click Assign. A green arrow
appears in the folder icon.
Figure C-27
Figure C-25
112
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
8. Select IP Addr. from the pull-down menu beside Remote Security
Gateway. This would be the IP Address of your Internet connection as seen
from the Internet. Enter this IP Address here.
Step Five: Create a Tunnel Through the Web-based Utility
Note: Further details on this step can be found in the VPN Tab section
in “Chapter 7: The Cable/DSL Firewall Router’s Web-based Utility”.
9. Select a type of encryption and authentication for the tunnel your are
establishing.
1. Open your web browser, and enter 192.168.1.1 in the Address field. Press
the Enter key.
10. Check PFS (Perfect Forward Secrecy) and enter the Pre-Shared Key and
Key Lifetime.
2. When the User name and Password field appears, skip the user name and
enter the default password admin. Press the Enter key.
11. Click the Apply button followed by the Continue button.
12. Click the Connect button.
3. From the Setup tab,
shown in Figure C-
28, click the VPN
tab.
Your tunnel should now be established.
Figure C-28
4. From the VPN tab, shown in Figure C-29, select Enable beside This
Tunnel.
5. Enter a Tunnel Name. This name should be unique for this particular tun-
nel.
6. Select Subnet from the pull-down menu beside Local Secure Group. Then,
enter the IP Address for this group. This would be the IP Address of the
local endpoint, your endpoint.
7. Select IP Addr. from the pull-down menu beside Remote Secure Group.
Then, enter the IP Address for this group. This would be the IP Address of
the remote endpoint, the endpoint on the other side of the tunnel.
Figure C-29
114
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Appendix E: How to Ping Your ISP’s
E-mail & Web Addresses
Virtually all Internet addresses are configured with words or characters (e.g.,
addresses are assigned to IP addresses, which are the true addresses on the
your web browser and you will wind up at the Linksys home page every time.
There are servers that translate the URL to an IP address; this is called Domain
Name System (DNS).
Appendix D: SNMP Functions
SNMP (Simple Network Management Protocol) is a widely-used network
monitoring and control protocol. Data is passed from a SNMP agent, such as
the EtherFast Cable/DSL Firewall Router with 4-Port 10/100 Switch/VPN
Endpoint to the workstation console used to oversee the network. The Router
then returns information contained in a MIB (Management Information Base),
which is a data structure that defines what is obtainable from the device and
what can be controlled (turned off, on, etc.).
SNMP functions, such as statistics, configuration, and device information, are
not available without third-party Management Software. The EtherFast
Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint is compatible
with all HP Openview compliant software.
IP and web addresses, however, can sometimes be long and hard to remember.
Because of this, certain ISPs will shorten their server addresses to single words
or codes on their users’ web browser or e-mail configurations. If your ISP’s e-
mail and web server addresses are configured with single words (www, e-mail,
home, pop3, etc.) rather than whole Internet addresses or IP addresses, the
Router may have problems sending or receiving mail and accessing the
Internet. This happens because the Router has not been configured by your ISP
to accept their abbreviated server addresses.
The solution is to determine the true web addresses behind your ISPs code
words. You can determine the IP and web addresses of your ISP’s servers by
“pinging” them.
Important: If you don’t have your ISP’s web and e-mail IP
addresses, you must either get them from your ISP or follow these
steps prior to connecting your Router to your network.
116
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Step Two: Pinging for a Web Address
Step One: Pinging an IP Address
The first step to determining your ISP’s web and e-mail server address is to
ping its IP address.
While the IP address returned above would work as your e-mail server address,
it may not be permanent. IP addresses change all the time. Web addresses, how-
ever, usually don’t. Because of this, you’re likely to have fewer problems by
configuring your system with web addresses rather than IP addresses. Follow
the instructions below to find the web address assigned to the IP address you
just pinged.
1. Power on the computer and the cable or DSL modem, and restore the
network configuration set by your ISP if you have since changed it.
2. Click Start, then Run, and type command. This will bring up the DOS
window.
1. At the DOS command prompt, type ping -a 24.53.32.4, where 24.53.32.4
is the IP address you just pinged. Information such as the following data
will be displayed.
3. At the DOS command prompt, type ping mail (assuming that the loca-
tion for which you’re trying to find an IP address is configured as mail).
Press Enter. Information such as the following data, taken from a ping of
Microsoft Network’s e-mail server, will be displayed.
C:\>ping -a 24.53.32.4
Pinging mail.msnv3.occa.home.com [24.53.32.4] with
32 bytes of data:
C:\>ping mail
Pinging mail [24.53.32.4] with 32 bytes of data:
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure E-2
2. Write down the web address returned by the ping command (In the
example in Figure C-2: mail.msnv3.occa.home.com is the web address).
This web address is the web address assigned to the IP address you just
pinged. While the IP address of mail could conceivably change, it is likely
that this web address will not.
Figure E-1
4. Write down the IP address returned by the ping command. (In the
example above: 24.53.32.4.) This IP address is the actual IP address of the
server mail, or any other word or value you have pinged.
3. Replace your ISP’s abbreviated server address with this extended web
address in the corresponding Internet application (web browser, e-mail
application, etc.).
Once you have replaced the brief server address with the true server address,
the Router should have no problem accessing the Internet through that Internet
application.
118
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
6. Find and double-click TCP/IP in the list to the right (see Figure F-2).
Appendix F: Installing the TCP/IP
Protocol
Follow these instructions to install the TCP/IP protocol on one of your PCs only
after a network card has been successfully installed inside the PC. These
instructions are for Windows 95, Windows 98, and Windows Me. For TCP/IP
setup under Windows NT, 2000, and XP, see your Windows documentation or
the Help feature.
1. Click the Start button. Choose Settings and then Control Panel.
Figure F-2
7. After a few seconds, the main Network window will appear. The TCP/IP
Protocol should now be listed.
2. Double-click on the Network icon to bring up your Network window.
Select the Configuration tab.
Figure F-1
Figure F-3
3. Click the Add button.
8. Click the OK button. Windows may ask for original Windows installation
files. Supply them as needed, e.g., c:\windows\options\cabs, D:\win98,
D:\win95, D:\win9x.
4. Double-click on Protocol.
5. Highlight Microsoft under the list of manufacturers.
9. Windows will ask you to restart the PC. Click the Yes button.
The TCP/IP installation is now complete.
120
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
3. Write down the Adapter Address as shown on your computer screen (see
Figure G-3). This is the MAC address for your Ethernet adapter and will
be shown as a series of numbers and letters.
Appendix G: Finding the MAC
Address and IP Address for Your
Ethernet Adapter
The MAC address/Adapter Address is what you will use for MAC Address
Cloning.
This section describes how to find the MAC address for your Ethernet adapter
to do MAC Address Cloning for the Router and ISP. You can also find the IP
address of your computer’s Ethernet adapter. The IP address is used for filter-
ing, forwarding, and DMZ. Follow the steps in this appendix to find the MAC
address or IP address for your adapter in Windows 95, 98, Me, NT, 2000, and
XP.
For Windows 95, 98, and Me:
1. Click on Start and Run. In the Open field, enter winipcfg. Then press the
Enter key or the OK button.
Figure G-3
The example in Figure G-3 shows the IP address of your Ethernet adapter
as 192.168.1.100. Your computer may show something different.
Note: The MAC address is also called the Adapter
Address.
For Windows NT, 2000, and XP:
Figure G-1
The following steps show an alternative way of obtaining the MAC address and
IP address for your Ethernet adapter.
2. When the IP Configuration window appears, select the Ethernet adapter
you are using to connect to the Router via a CAT 5 Ethernet cable.
1. Click on Start and Run. In the Open field, enter cmd. Press the Enter key
or click the OK button.
Figure G-4
Figure G-2
122
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
2. In the command prompt, enter ipconfig /all. Then press the Enter key.
When entering information for MAC Address Cloning, type the 12-digit MAC
address (see Figure G-6).
Figure G-6
Figure G-5
3. Write down the Physical Address as shown on your computer screen; it is
the MAC address for your Ethernet adapter. This will appear as a series of
letters and numbers.
The MAC address/Physical Address is what you will use for MAC Address
Cloning.
Note: The MAC address is also called the Physical
Address.
The example in Figure G-5 shows the IP address of your Ethernet adapter
as 192.168.1.100. Your computer may show something different.
124
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Cable Modem - A device that connects a computer to the cable television net-
work, which in turn connects to the Internet. Once connected, cable modem
users have a continuous connection to the Internet. Cable modems feature
asymmetric transfer rates: around 36 Mbps downstream (from the Internet to
the computer), and from 200 Kbps to 2 Mbps upstream (from the computer to
the Internet).
Appendix H: Glossary
3DES - 3DES is a variation on DES that uses a 168-bit key.
Adapter - Printed circuit board that plugs into a PC to add to capabilities or
connectivity to a PC.
CAT 5 - ANSI/EIA (American National Standards Institute/Electronic
Industries Association) Standard 568 is one of several standards that specify
"categories" (the singular is commonly referred to as "CAT") of twisted pair
cabling systems (wires, junctions, and connectors) in terms of the data rates
that they can sustain. CAT 5 cable has a maximum throughput of 100 Mbps and
is usually utilized for 100BaseTX networks.
AppleTalk - An Apple Computer networking system that supports Apple's pro-
prietary local talk.
Backbone - The part of a network that connects most of the systems and net-
works together and handles the most data.
Cookie - Data created by a Web server that is stored on a user's computer. It
provides a way for the Web site to keep track of a user's patterns and prefer-
ences and, with the cooperation of the Web browser, to store them on the user's
own hard disk.
Bit - A binary digit. The value - 0 or 1-used in the binary numbering system.
Also, the smallest form of data.
Boot - To cause the computer to start executing instructions. Personal comput-
ers contain built-in instructions in a ROM chip that are automatically executed
on startup. These instructions search for the operating system, load it and pass
control to it.
Data Packet - One frame in a packet-switched message. Most data communi-
cations is based on dividing the transmitted message into packets. For example,
an Ethernet packet can be from 64 to 1518 bytes in length.
Bridge - A device that interconnects different networks together.
DDNS (Dynamic Domain Name System) - Allows a network device with a
dynamic Internet IP address to have a fixed host and domain name, such as
myhostname.mydomainname.com. It is useful when you are hosting your own
website, FTP server, or other server behind a router, so people can find your
site no matter how often the Internet IP address changes. Using DDNS requires
registering with a DDNS service provider on the Internet.
Broadband - A data-transmission scheme in which multiple signals share the
bandwidth of a medium. This allows the transmission of voice, data and video
signals over a single medium. Cable television uses broadband techniques to
deliver dozens of channels over one cable.
Browser - A browser is an application program that provides a way to look at
and interact with all the information on the World Wide Web or PC. The word
"browser" seems to have originated prior to the Web as a generic term for user
interfaces that let you browse text files online.
Default Gateway - The routing device used to forward all traffic that is not
addressed to a station within the local subnet.
Denial of Service - A protocol that directs the network to no longer respond to
requests that might arise as the result of a Denial of Service attack.
Buffer - A buffer is a shared or assigned memory area used by hardware
devices or program processes that operate at different speeds or with different
sets of priorities. The buffer allows each device or process to operate without
being held up by the other. In order for a buffer to be effective, the size of the
buffer and the algorithms for moving data into and out of the buffer need to be
considered by the buffer designer. Like a cache, a buffer is a "midpoint holding
place" but exists not so much to accelerate the speed of an activity as to sup-
port the coordination of separate activities.
Denial of Service Attack - An assault on a network that floods it with so many
additional requests that regular traffic is either slowed or completely interrupt-
ed.
DES (Digital Encryption Standard) - Encryption used for data communication
where both the sender and receiver must know the same secret key, used to
126
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
encrypt and decrypt the data, or to generate and verify a message authentica-
tion code. Linksys DES encryption uses a 56-bit key.
employing unused bandwidth, still allows for normal phone usage. DSL pro-
vides "always-on" operation, eliminating the need to dial in to the service.
DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network
administrators manage centrally and automate the assignment of Internet
Protocol (IP) addresses in an organization's network. Using the Internet's set of
protocol (TCP/IP), each machine that can connect to the Internet needs a
unique IP address. When an organization sets up its computer users with a con-
nection to the Internet, an IP address must be assigned to each machine.
Without DHCP, the IP address must be entered manually at each computer and,
if computers move to another location in another part of the network, a new IP
address must be entered. DHCP lets a network administrator supervise and dis-
tribute IP addresses from a central point and automatically sends a new IP
address when a computer is plugged into a different place in the network.
Dynamic IP Address - An IP address that is automatically assigned to a client
station in a TCP/IP network, typically by a DHCP server. Network devices that
serve multiple users, such as servers and printers, are usually assigned static IP
addresses.
Dynamic Routing - The ability for a router to forward data via a different route
based on the current conditions of the communications circuits. For example,
it can adjust for overloaded traffic or failing lines and is much more flexible
than static routing, which uses a fixed forwarding path.
Encryption - A security method that applies a specific algorithm to data in
order to alter the data's appearance and prevent other devices from reading the
information.
DHCP uses the concept of a "lease" or amount of time that a given IP address
will be valid for a computer. The lease time can vary depending on how long a
user is likely to require the Internet connection at a particular location. It's espe-
cially useful in education and other environments where users change fre-
quently. Using very short leases, DHCP can dynamically reconfigure networks
in which there are more computers than there are available IP addresses.
Ethernet - IEEE standard network protocol that specifies how data is placed
on and retrieved from a common transmission medium. Has a transfer rate of
10 Mbps. Forms the underlying transport vehicle used by several upper-level
protocols, including TCP/IP and XNS.
DHCP supports static addresses for computers containing Web servers that
need a permanent IP address.
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet
CSMA/CD network access method.
DMZ (Demilitarized Zone) - Allows one IP address (or computer) to be
exposed to the Internet. Some applications require multiple TCP/IP ports to be
open. It is recommended that you set your computer with a static IP address if
you want to use DMZ Hosting.
Finger - A UNIX command widely used on the Internet to find out informa-
tion about a particular user, such as telephone number, whether currently
logged on or the last time logged on. The person being "fingered" must have
placed his or her profile on the system. Fingering requires entering the full
user@domain address.
DNS - The domain name system (DNS) is the way that Internet domain name
are located and translated into Internet Protocol (IP) addresses. A domain name
is a meaningful and easy-to-remember "handle" for an Internet address.
Firewall - A firewall is a set of related programs, located at a network gateway
server, that protects the resources of a network from users from other networks.
(The term also implies the security policy that is used with the programs.) An
enterprise with an intranet that allows its workers access to the wider Internet
installs a firewall to prevent outsiders from accessing its own private data
resources and for controlling what outside resources to which its own users
have access.
Domain - A subnetwork comprised of a group of clients and servers under the
control of one security database. Dividing LANs into domains improves per-
formance and security.
Download - To receive a file transmitted over a network. In a communications
session, download means receive, upload means transmit.
Basically, a firewall, working closely with a router, examines each network
packet to determine whether to forward it toward its destination.
DSL (Digital Subscriber Line) - A technology that dramatically increases the
digital capacity of ordinary telephone lines into the home or office and, by
128
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Firmware - Code that is written onto read-only memory (ROM) or program-
mable read-only memory (PROM). Once firmware has been written onto the
ROM or PROM, it is retained even when the device is turned off.
Hub - The device that serves as the central location for attaching wires from
workstations. Can be passive, where there is no amplification of the signals; or
active, where the hubs are used like repeaters to provide an extension of the
cable that connects to a workstation.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP
network (Internet, UNIX, etc.). For example, after developing the HTML pages
for a Web site on a local machine, they are typically uploaded to the Web serv-
er using FTP.
ICMP (Internet Control Message Protocol) - Part of the TCP/IP protocol.
Network devices such as routers or servers use ICMP to transmit error mes-
sages and control messages. For example, the PING program uses ICMP.
FTP includes functions to log onto the network, list directories and copy files.
It can also convert between the ASCII and EBCDIC character codes. FTP oper-
ations can be performed by typing commands at a command prompt or via an
FTP utility running under a graphical interface such as Windows. FTP transfers
can also be initiated from within a Web browser by entering the URL preceded
with ftp://.
ICQ - A conferencing program for the Internet that provides interactive chat,
e-mail and file transfer and can alert you when someone on your predefined list
has also come online.
IEEE (The Institute of Electrical and Electronics Engineers) - The IEEE
describes itself as "the world's largest technical professional society, promoting
the development and application of electrotechnology and allied sciences for
the benefit of humanity, the advancement of the profession, and the well-being
of our members."
Unlike e-mail programs in which graphics and program files have to be
"attached," FTP is designed to handle binary files directly and does not add the
overhead of encoding and decoding the data.
The IEEE fosters the development of standards that often become national and
international standards. The organization publishes a number of journals, has
many local chapters, and several large societies in special areas, such as the
IEEE Computer Society.
Full Duplex - The ability of a device or line to transmit data simultaneously in
both directions.
Gateway - A device that interconnects networks with different, incompatible
communications protocols.
IKE (Internet Key Exchange) - A negotiation and key exchange protocol spec-
ified by the Internet Engineering Task Force. An IKE security association (SA)
automatically negotiates encryption and authentication keys. With IKE, an ini-
tial exchange authenticates the VPN session and automatically negotiates keys
that will be used to pass encrypted data over the Internet or any other network.
Half Duplex - Data transmission that can occur in two directions over a single
line, but only one direction at a time.
Hardware - Hardware is the physical aspect of computers, telecommunica-
tions, and other information technology devices. The term arose as a way to dis-
tinguish the "box" and the electronic circuitry and components of a computer
from the program you put in it to make it do things. The program came to be
known as the software.
IP (Internet Protocol) - The method or protocol by which data is sent from one
computer to another on the Internet. It is a standard set of rules, procedures, or
conventions relating to the format and timing of data transmission between two
computers that they must accept and use to be able to understand each other.
Hop - The link between two network nodes.
IP Address - In the most widely installed level of the Internet Protocol (IP)
today, an IP address is a 32-binary digit number that identifies each sender or
receiver of information that is sent in packet across the Internet. When you
request an HTML page or send e-mail, the Internet Protocol part of TCP/IP
includes your IP address in the message (actually, in each of the packets if more
than one is required) and sends it to the IP address that is obtained by looking
up the domain name in the Uniform Resource Locator you requested or in the
HTTP (HyperText Transport Protocol) - The communications protocol used
to connect to servers on the World Wide Web. Its primary function is to estab-
lish a connection with a Web server and transmit HTML pages to the client
browser.
130
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
e-mail address you're sending a note to. At the other end, the recipient can see
the IP address of the Web page requestor or the e-mail sender and can respond
by sending another message using the IP address it received.
Multicasting - Sending data to a group of nodes instead of a single destination.
NAT (Network Address Translation) - The translation of an Internet Protocol
address (IP address) used within one network to a different IP address known
within another network. One network is designated the inside network and the
other is the outside.
IPSec (Internet Protocol Security) - A suite of protocols used to implement
secure exchange of packets at the IP layer. IPSec supports two basic modes:
Transport and Tunnel. Transport encrypts the payload of each packet, leaving
the header untouched, while Tunnel mode encrypts both the header and the pay-
load and is therefore more secure. IPSec must be supported on both transmit-
ter and receiver and must share a public key. Tunnel mode is widely deployed
in VPNs (Virtual Private Networks).
NetBIOS - The native networking protocol in DOS and Windows networks.
Although originally combined with its transport layer protocol (NetBEUI),
NetBIOS today provides a programming interface for applications at the ses-
sion layer (layer 5). NetBIOS can ride over NetBEUI, its native transport,
which is not routable, or over TCP/IP and IPX/SPX, which are routable proto-
cols.
IPX (Internetwork Packet EXchange) - A NetWare communications protocol
used to route messages from one node to another. IPX packets include network
addresses and can be routed from one network to another.
NetBIOS computers are identified by a unique 15-character name, and
Windows machines (NetBIOS machines) periodically broadcast their names
over the network so that Network Neighborhood can catalog them. For TCP/IP
networks, NetBIOS names are turned into IP addresses via manual configura-
tion in an LMHOSTS file or a WINS server.
ISP (Internet Service Provider) - A company that provides individuals and
companies access to the Internet and other related services such as Web site
building and virtual hosting.
LAN (Local Area Network) - A group of computers and associated devices that
share a common communications line and typically share the resources of a
single processor or server within a small geographic area (for example, within
an office building).
There are two NetBIOS modes. The Datagram mode is the fastest mode, but
does not guarantee delivery. It uses a self-contained packet with send and
receive name, usually limited to 512 bytes. If the recipient device is not listen-
ing for messages, the datagram is lost. The Session mode establishes a connec-
tion until broken. It guarantees delivery of messages up to 64KB long.
MAC (Media Access Control) Address - A unique number assigned by the
manufacturer to any Ethernet networking device, such as a network adapter,
that allows the network to identify it at the hardware level.
Network - A system that transmits any combination of voice, video and/or data
between users.
Mbps (Megabits per second) - One million bits per second; unit of measure-
Network Mask - Also known as the "Subnet Mask".
ment for data transmission.
NNTP (Network News Transfer Protocol) - The protocol used to connect to
MD5 - A type of one-way authentication method that uses passwords. MD5
authentication is not as secure as the EAP-TLS or EAP/TTLS authentication
methods.
Usenet groups on the Internet. Usenet newsreaders support the NNTP protocol.
Node - A network junction or connection point, typically a computer or work
station.
MIB (Management Information Base) - A set of database objects. This set con-
tains information about a specific device for utilizing SNMP.
Notebook (PC) - A notebook computer is a battery-powered personal comput-
er generally smaller than a briefcase that can easily be transported and conve-
niently used in temporary spaces such as on airplanes, in libraries, temporary
offices, and at meetings. A notebook computer, sometimes called a laptop com-
puter, typically weighs less than five pounds and is three inches or less in thick-
ness.
mIRC - mIRC runs under Windows and provides a graphical interface for log-
ging onto IRC servers and listing, joining and leaving channels.
132
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Packet - A unit of data routed between an origin and a destination in a network.
RIP (Routing Information Protocol) - A simple routing protocol that is part of
the TCP/IP protocol suite. It determines a route based on the smallest hop count
between source and destination. RIP is a distance vector protocol that routine-
ly broadcasts routing information to its neighboring routers.
Packet Filtering - Discarding unwanted network traffic based on its originat-
ing address or range of addresses or its type (e-mail, file transfer, etc.).
Ping (Packet INternet Groper) - An Internet utility used to determine whether
a particular IP address is online. It is used to test and debug a network by send-
ing out a packet and waiting for a response.
RJ-45 (Registered Jack-45) - A connector similar to a telephone connector that
holds up to eight wires, used for connecting Ethernet devices.
Router - Protocol-dependent device that connects subnetworks together.
Routers are useful in breaking down a very large network into smaller subnet-
works; they introduce longer delays and typically have much lower throughput
rates than bridges.
Plug-and-Play - The ability of a computer system to configure expansion
boards and other devices automatically without requiring the user to turn off
the system during installation.
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the
Internet. It provides a message store that holds incoming e-mail until users log
on and download it. POP3 is a simple system with little selectivity. All pending
messages and attachments are downloaded at the same time. POP3 uses the
SMTP messaging protocol.
Security Association - A group of security settings related to a specific VPN
tunnel.
Server - Any computer whose function in a network is to provide user access
to files, printing, communications, and other services.
Port - A pathway into and out of the computer or a network device such as a
switch or router. For example, the serial and parallel ports on a personal com-
puter are external sockets for plugging in communications lines, modems and
printers.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the
Internet. It is a TCP/IP protocol that defines the message format and the mes-
sage transfer agent (MTA), which stores and forwards the mail.
SNMP (Simple Network Management Protocol) - A widely used network
monitoring and control protocol. Data is passed from SNMP agents, which are
hardware and/or software processes reporting activity in each network device
(hub, router, bridge, etc.) to the workstation console used to oversee the net-
work. The agents return information contained in a MIB (Management
Information Base), which is a data structure that defines what is obtainable
from the device and what can be controlled (turned off, on, etc.).
PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a method for the
encapsulation of PPP packets over Ethernet frames from the user to the ISP
over the Internet. One reason PPPoE is preferred by ISPs is because it provides
authentication (username and password) in addition to data transport. A PPPoE
session can be initiated by either a client application residing on a PC, or by
client firmware residing on a modem or router.
PPTP (Point-to-Point Tunneling Protocol) - A protocol which allows the Point
to Point Protocol (PPP) to be tunneled through an IP network. PPTP does not
specify any changes to the PPP protocol but rather describes a "tunneling serv-
ice" for carrying PPP (a tunneling service is any network service enabled by
tunneling protocols such as PPTP, L2F, L2TP, and IPSEC tunnel mode). One
example of a tunneling service is secure access from a remote small office net-
work to a headquarters corporate intranet via a Virtual Private Network (VPN)
that traverses the Internet. However, tunneling services are not restricted to cor-
porate environments and may also be used for personal (i.e., non-business)
applications.
Software - Instructions for the computer. A series of instructions that performs
a particular task is called a "program." The two major categories of software are
"system software" and "application software." System software is made up of
control programs such as the operating system and database management sys-
tem (DBMS). Application software is any program that processes data for the
user.
SPI (Stateful Packet Inspection) - A firewall technology that monitors the state
of the transaction so that it can verify that the destination of an inbound pack-
et matches the source of a previous outbound request. It examines not just the
headers of the packet, but also the contents, to determine more about the pack-
134
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
et than just its source and destination information. It is called "stateful" because
verifies that the stated destination computer has previously requested the cur-
rent communication. In this way, it verifies that all communications are initiat-
ed by the recipient computer and are taking place only with sources that are
known and trusted from previous interactions. In addition to being a more rig-
orous inspection, stateful packet inspection closes off ports until connection to
the specific port is requested. This allows an added layer of protection from the
threat of port scanning.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol
that has no directory or password capability.
Throughput - The amount of data moved successfully from one place to
another in a given time period.
UDP (User Datagram Protocol) - A method (protocol) used along with the IP
(Internet Protocol) to send data in the form of message units (datagram)
between network devices over a LAN or WAN. While IP takes care of handling
the actual delivery of the data (routing), UDP takes care of keeping track of the
individual units of data (called packets) that a message is divided into for effi-
cient delivery over the network. UDP is known as a "connection-less" protocol
due to NOT requiring the receiver of a packet to return an acknowledgment of
receipt to the sender of the packet (as opposed to TCP).
Static IP Address - A permanent IP address that is assigned to a node in an IP
or a TCP/IP network.
Static Routing - Forwarding data in a network via a fixed path. Static routing
cannot adjust to changing line conditions as can dynamic routing.
Subnet Mask - The method used for splitting IP networks into a series of sub-
groups, or subnets. The mask is a binary pattern that is matched up with the IP
address to turn part of the host ID address field into a field for subnets.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network. In a communications session,
upload means transmit, download means receive.
Switch - 1. A data switch connects computing devices to host computers,
allowing a large number of devices to share a limited number of ports. 2. A
device for making, breaking, or changing the connections in an electrical cir-
cuit.
URL (Uniform Resource Locator) - The address that defines the route to a file
on the Web or any other Internet facility. URLs are typed into the browser to
access Web pages, and URLs are embedded within the pages themselves to pro-
vide the hypertext links to other pages.
TCP (Transmission Control Protocol) - A method (protocol) used along with
the IP (Internet Protocol) to send data in the form of message units (datagram)
between network devices over a LAN or WAN. While IP takes care of handling
the actual delivery of the data (routing), TCP takes care of keeping track of the
individual units of data (called packets) that a message is divided into for effi-
cient delivery over the network. TCP is known as a "connection oriented" pro-
tocol due to requiring the receiver of a packet to return an acknowledgment of
receipt to the sender of the packet resulting in transmission control.
VPN (Virtual Private Network) - A technique that allows two or more LANs to
be extended over public communication channels by creating private commu-
nication subchannels (tunnels). Effectively, these LANs can use a WAN as a
single large "virtually private" LAN. This removes the need to use leased lines
for WAN communications through secure use of a publicly available WAN
(such as the Internet). Examples of VPN technology are: PPTP (Point to Point
Tunneling Protocol), L2TP (Layer 2 Tunneling Protocol), and IPSec (Internet
Protocol Security).
TCP/IP (Transmission Control Protocol/Internet Protocol) - The basic com-
munication language or set of protocols for communications over a network
(developed specifically for the Internet). TCP/IP defines a suite or group of
protocols and not only TCP and IP.
VPN end point - VPN end point capability within a router provides the ability
to initiate a VPN tunnel to some other location that supports either a VPN client
or has VPN end point capability.
Telnet - A terminal emulation protocol commonly used on the Internet and
TCP/IP-based networks. It allows a user at a terminal or computer to log onto
a remote device and run a program.
WAN (Wide Area Network)- A communications network that covers a rela-
tively large geographic area, consisting of two or more LANs. Broadband com-
munication over the WAN is often through public networks such as the tele-
136
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
phone (DSL) or cable systems, or through leased lines or satellites. In its most
basic definition, the Internet could be considered a WAN.
Appendix I: Specifications
WINIPCFG - Configuration utility based on the Win32 API for querying,
defining and managing IP addresses within a network. A commonly used util-
ity for configuring networks with static IP addresses.
Model Number
Standards
Protocol
Ports
BEFSX41
IEEE 802.3, IEEE 802.3u
CSMA/CD
WAN:
LAN:
One 10/100 RJ-45 Port
Four 10/100 RJ-45 Ports (One with DMZ
Functionality)
Cabling Type
Topology
UTP Category 5 or Better
Star
Speed (Mbps)
WAN:
10/100 (Half Duplex)
20/200 (Full Duplex)
10/100 (Half Duplex)
20/200 (Full Duplex)
Power, Diag, DMZ
LAN:
LED Indicators
WAN:
LAN:
Link/Act, Full/Col, 10/100
Link/Act, Full/Col, 10/100
Environmental
Dimensions
7.31" x 1.88" x 6.16"
(186 mm x 48 mm x 154 mm)
13.6 oz. (0.38 kg)
Unit Weight
Power Input
12 V AC, 1000 mA
Certifications
FCC Class B, CE Mark
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
0°C to 40°C (32°F to 104°F)
-20°C to 70°C (-4°F to 158°F)
10% to 85%, Non-Condensing
5% to 90%, Non-Condensing
138
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Broadband® Series
EtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint
Appendix J: Warranty Information
Appendix K: Contact Information
BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE
FROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.
RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF
PURCHASE.
For help with the installation or operation of the EtherFast Cable/DSL Firewall
Router, contact Linksys Technical Support at one of the phone numbers or
Internet addresses below.
Sales Information
Technical Support
RMA (Return Merchandise
Authorization) Issues
Fax
Email
Web
FTP Site
800-546-5797 (LINKSYS)
800-326-7114
IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY
PRODUCT.
949-265-6655
ftp.linksys.com
LINKSYS OFFERS CROSS SHIPMENTS, A FASTER PROCESS FOR PRO-
CESSING AND RECEIVING YOUR REPLACEMENT. LINKSYS PAYS
FOR UPS GROUND ONLY. ALL CUSTOMERS LOCATED OUTSIDE OF
THE UNITED STATES OF AMERICA AND CANADA SHALL BE HELD
RESPONSIBLE FOR SHIPPING AND HANDLING CHARGES. PLEASE
CALL LINKSYS FOR MORE DETAILS.
140
141
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2003 Linksys, All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|