INSTALLATION AND OPERATION MANUAL
Free-Standing
EPA Certified
Wood-Burning Stoves
Save These Instructions
For Future Reference
P/N 775,216M, Rev. E, 02/2010
Wood Stoves
Model Legacy™ S260 T-Top
A French manual is available upon request. Order P/N 775,216CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 775,216CF.
Theseappliancesmustbeproperlyinstalledandoperatedinordertopreventthe
possibility of a house fire. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow
these instructions could result in property damage, bodily injury or
Portland
evendeath.Contactyourlocalbuildingorfireofficialstoobtain
US
apermitandinformationonanyinstallationrequirements
and inspection requirements in your area.
Report # 050-S-02b-2
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Inspect your chimney at least once a month during the burn-
ing season to check for soot and creosote accumulations.
Any accumulations over 1/4” thick should be removed by a
professionalchimneysweep.Donotattempttoburnoutheavy
creosoteaccumulationswithahotfire. Iflargeaccumulations
are occurring, review your burning procedures.
14. If a creosote fire should develop, the fire department should
be called immediately and then attempts should be made to
control the fire until assistance arrives. If a “runaway” fire
should develop causing over-heating of the stove, the door
and draft regulators should be closed immediately. The fire
should die down once deprived of oxygen. After a severe
chimneyfire,thecompletechimneysystemshouldbechecked
before further use.
15. Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly
On Hearth (firebrick). Do not use andirons or other methods
of supporting the fuel.
16. Please read this entire manual before you install and use your
new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
17. Check all local building and safety codes before installation.
The installation instructions and appropriate code require-
ments must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
18. In the U.S.A, install in accordance with the National Fire
Protection Association’s Code, NFPA 211, Standards for
Chimneys, Fireplaces, Vents and Solid-Fuel-Burning Appli-
ances, or similar regulations, may apply to the installation of
a Solid-Fuel-Burning appliance in your area. In Canada, the
guidelineisestablishedbytheCSAStandard,CAN/CSA-B365-
M93,InstallationCodeforSolid-Fuel-BurningAppliancesand
Equipment.
19. Do not connect to any air distribution duct or system.
20. WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH
MAY LEAD TO DEATH!
21. Carbon Monoxide Poisoning – Early signs of carbon monox-
ide poisoning resemble the flu with headaches, dizziness, or
nausea. If you have these signs, get fresh air at once! Have
the heater inspected by a qualified service technician. Some
people are more affected by carbon monoxide than others.
These include pregnant women, people with heart or lung
disease or anemia, those under the influence of alcohol, and
those at high altitudes.
IMPORTANT SAFETY AND WARNIING
INFORMATION
READ THIS MANUAL IN ITS ENTIRETY AND UNDER-
STAND THESE RULES TO FOLLOW FOR SAFETY.
1. When this room heater is not properly installed, a house fire
may result. To reduce the risk of fire, follow the installation
instructions. Contact local building or fire officials about
restrictions and installation inspection requirements in your
area.
2. Wear gloves during installation to avoid injury from sharp
edges on the stove and/or its parts.
3. This unit is designed and engineered to burn only dry, well-
seasoned wood. Burning wet wood will greatly reduce your
stoves efficiency, produce excessive amounts of smoke and
can cause dangerous chimney fires due to creosote build-
up.
4. Before opening the door, the draft control must be fully open
to avoid possible combustion flash (ignition of hot volatile
gases as the door is opened).
5. Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or ’freshenup’
a fire in this heater. Keep all such liquids well away from the
heater while it is in use.
6. While burning, fuel utilizes oxygen from the air in the room.
Be sure to allow an adequate amount of fresh air into the
room where the stove is burning.
7. The outside surface of the stove will be hot while burning
properly and can set items like clothing and curtains on fire.
Keep furnishings and other combustible materials away from
the stove. Using the heat from the stove to dry wet clothing
can be hazardous if clothes are placed too near the surface
of the stove.
8. Hot while in operation. Keep children, clothing furnishings
and combustible material a considerable distance away.
Contact may cause skin burns. Do not allow children to play
near the stove without close supervision. Do not touch the
stove while it is burning. Use extreme caution while the unit
is in use. Surface temperatures become dangerously hot and
can cause serious burns.
9. Do not allow anyone to operate the stove who is not familiar
with the operating instructions.
10. Attemptstoachieveheatoutputratesthatexceedstovedesign
specifications can result in permanent damage to the stove.
Never leave your stove unattended on high burn rates. This
may cause overfiring. Overfiring the stove may cause a house
fire. If the stove glows, you are overfiring.
22. Failure to use manufacturer provided parts, variations in tech-
niquesandconstructionmaterialsorpracticesotherthanthose
described in this manual may create a fire hazard and void the
limited warranty.
23. Donotmakeanymake-shiftcompromisesduringinstallation.
Any modification or alteration may result in damage to the
appliance or dwelling and will void the warranty, certification
and listings of this unit.
24. These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate heat source
when installed in a dwelling.
25. Do Not Overfire – If Heater or Chimney Connector Glows,
You Are Overfiring.
11. Keep a water hose or hand-operated fire extinguisher close
for safety.
12. Smoke Detectors - Since there are always several potential
sources of fire in any home, we recommend installing smoke
detectors. If possible, install the smoke detector in a hallway
adjacent to the room (to reduce the possibility of occasional
false activation from the heat produced by the stove). If your
local code requires a smoke detector be installed within the
same room, you must follow the requirements of your local
code. Check with your local building department for require-
ments in your area.
26. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERV-
ING ANOTHER APPLIANCE.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
W.C. As per NFPA-211 standard (see paragraph below), the installer
must take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements of the
appliance. See Chimney Guidelines below to assist you in selecting the
proper venting system for your installation.
TESTING INFORMATION
ThismanualdescribestheinstallationandoperationoftheLegacy™S260
non-catalytic wood heaters. These heaters meet the U.S. Environmental
Protection Agency’s emissions limits for wood heaters sold on or after
July 1, 1990. This heater has been developed, tested and constructed
in accordance with the requirements of UL 1482, ULC S627 and HUD
standards and is listed by OMNI Test Laboratories, Portland, OR. It has
been approved for residential, mobile home and alcove installations.
American National Standards Institute ANSI/NFPA ꢀ11, Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
- See Draft Section: A chimney or vent shall be so designed and con-
structed to develop a flow sufficient to completely remove all flue and
vent gases to the outside atmosphere. The venting system shall satisfy
the draft requirements of the connected appliance in accordance with the
manufacturer’s instructions.
DRAFT REqUIREMENTS
Chimney Guidelines:
Your wood stove is dependent upon a properly functioning chimney for
optimum performance. It is a high efficiency appliance that loses much
less heat up the chimney than older appliances and fireplaces. For this
reason it is important to match the stove to the chimney. The chimney
has two functions:
• This appliance requires approximately 12 feet minimum of “effective
draw” provided by the venting system. As a rule of thumb, every 90
degree total direction change in the venting will result in a loss of
approximately 5 feet of “effective draw.” Example: If two 45 degree
offsets are used, subtract 5 feet from the actual vertical vent height
to determine your “effective draw.” In this case if you had 14 feet of
vertical vent, the effective draw would only be approximately 9 feet
(14 ft. - 5 ft. = 9 ft.), therefore it may be necessary to add additional
height to the venting system.
1. It draws combustion air into the appliance (without air, no fuel will
burn) and
2. It exhausts combustion by-products. Your new Country™ Collection
stove is what is known as a “natural draft” appliance.
• Do not install an offset within the first two feet above the flue outlet
on the appliance.
• If the venting system is all vertical and the total vent length above the
flue outlet exceeds 14 feet, it is recommended that the 8” to 6” pipe
reducer is used (cat. no. 71134) and a 6” venting system be installed.
At higher elevations, this may not be necessary.
• Inwellinsulatedandweathertighthomes,itmaybedifficulttoestablish
a good draft up your chimney. The poor draft is caused by a shortage
of air in the house. In this situation an Outside Air Kit may need to
be installed (See Negative Pressure Warning on Page 5 and Outside
Combustion Air on Page 8).
The appliance depends solely on the natural draft of the chimney system
to draw combustion air into the unit. Draft is the force that moves air from
the appliance up into the chimney. The amount of draft in your chimney
dependsonthelengthofthechimney,localgeography,nearbyobstructions
andotherfactors.Toomuchdraftmaycauseexcessivetemperaturesinthe
appliance (overfiring). Slow or inadequate draft equals poor combustion
and possible smoking problems. The following are some conditions that
may contribute to poor chimney draft:
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate draft.
3. A chimney with excessive height (this may allow exhaust to cool too
much before exiting, which will stall the rate the exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney Guide-
lines).
Chimney Height Requirements
The chimney must extend 3’ (.92m) above the level of roof penetration
and a minimum of 2’ (.61m) higher than any roof surface within 10’
(3m) (see below). Check with your local building officials for additional
requirements for your area.
Inadequate draft will cause the appliance to leak smoke into the room
through the stove and the chimney connector joints.
Excessive draft may cause an uncontrollable burn or a glowing red stove
or chimney part.
Less than
10' (3 m)
Overfiring Damage - If the heater or chimney connector glows, you are
overfiring. Other symptoms may include: Cracking, warping or burning
out of components, plated doors may turn color, stove glass may develop
a haze, which will not come off with cleaning.
2’ (610 mm) Min.
3' (914 mm)
3'
Min.
10'
(3 m)
Overfiring of a stove is a condition where excessive temperatures are
reached, beyond the design capabilities of the appliance. The damage
that occurs from overfiring is not covered under the manufacturer’s
limited warranty.
(914 mm)
Min.
Also see Troubleshooting on Page 17.
Figure 1 - Chimney Height Requirements
SELECTING THE PROPER VENTING SYSTEM
To pass inspection in nearly any jurisdiction, the chimney must meet both
safety and exhaust flow requirements. The (3’ by) 2’ by 10’ rule applies
to both masonry and factory-built chimneys.
The appliance is merely one component of a larger system. The other
equally important component is the venting system. This is necessary for
achieving the required flow of combustion air to the fire chamber and for
safely removing unwanted combustion byproducts from the appliance.
If the venting system’s design does not promote these ends, the system
maynotfunctionproperly.Poorlyfunctioningventingsystemsmaycreate
performance problems as well as be a safety hazard. A draft test should
read greater than .0ꢂ’ W.C. (inches water column) and less than .08”
* Ref. USA - National Standard, NFPA 211-latest edition and Canada
National Standard CSA B365-01-latest edition. Vents installed with a
listed cap shall terminate in accordance with the terms of the cap’s
listings.
ꢂ
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dry, seasoned wood is that which has been cut, split and allowed to dry
under a covered area where air is free to flow and circulate under and
around the wood (not under a tarp or plastic). Make sure wood is not
stackeddirectlyontheground,itmayabsorbmoisturefromtheground.It
shouldbeallowedtodryintheseconditionsforaminimumofsixmonths,
preferablyoneyearormore.ITMUSTBEUNDERSTOODTHATWOOD
CANNOT BE LEFT IN ANY KIND OF WET OR DAMP AREA OR IT
WILL NEVER BECOME COMPLETELY SEASONED.
NEGATIVE PRESSURE WARNING
This appliance is not designed to be operated in a negative pressure.
In very airtight homes with large kitchen exhaust fans, furnace cold air
returns, fresh air exchange systems and any other air system in close
proximity to the heating appliance may create a negative pressure in the
same room as the heating appliance. This can create dangerous back
draftingofthestoveandchimneyjoints,drawingcombustionby-products
into the home. Be sure your home has adequate makeup air to eliminate
negative pressures caused by the above-mentioned sources. Outside air
connected to the appliance probably will not resolve such a problem as
the stove or fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from negative
pressures described here.
Your stove will not operate at the level that it is meant to unless you use
seasoned, dry wood. Do not burn driftwood or wood that has been in salt
water, doing so will void your warranty. Do not burn treated wood, coal,
garbage, cardboard, solvents, or colored paper. Burning treated wood,
garbage, solvents, or colored paper may result in the release of toxic
fumes. This type of burning will also void your warranty.
Ventilation Requirements - Provide adequate air for combustion. The
fresh air requirements of this appliance must be met within the space
where it will be installed. Ventilation is essential when using a Solid-Fuel-
Burning heater. In well insulated and weather tight homes, it may be
difficult to establish a good draft up the chimney (caused by a shortage
of air in the home). The lack of air is caused by many common household
appliances which exhaust air from the home (such as a furnace, heat
pump, air conditioner, clothes dryer, exhaust fans, fireplaces, and other
fuel burning appliances). Also, the combustion process of this heater
uses oxygen from inside the dwelling. If the available fresh air delivery
in the dwelling is insufficient to support the demands of these appliances,
problems can result (i.e. excessive negative pressure can develop in the
dwelling which will affect the rate at which this appliance can draft thus
resulting in performance problems. To correct this problem it may help
to open a window (preferably on the windward side of the house) or
install an optional outside air kit.
PAINT CURING
If your stove has a Gold or Nickel-Plated Door, be sure to clean it
with a household type glass cleaner and a very soft cloth to remove
any fingerprints and residues prior to the first fire and before any fire
if the gold has been handled or soiled. Do not close the door tightly
during the “Burn-In Period.” Also, open the door frequently (every
ꢃ-10 minutes) to keep the gasket from adhering to the curing paint.
Ventilate the house well during these first firings as the paint gives off
carbon dioxide and unpleasant odors. It is recommended that persons
sensitive to an imbalance in the indoor air quality avoid the stove during
the curing process.
Your new Legacy™ 260 stove is painted with a High Temperature Paint
that cures during the first few firings. We recommend that you put your
stove through a regimen of three burns. The first two should last for
20 minutes each at 250 degrees ( the stove should be allowed to cool
completely between each burn). The third should be a burn of at least 450
degreesF. for45-60minutes. Thepaintwillbecomesoft, gummyandemit
non-toxic smoke during these burns. After the stove cools down for the
third time, the paint will harden. DO NOT BUILD A LARGE ROARING
FIRE UNTIL THIS CURING EFFECT IS COMPLETE OR YOU MAY
DAMAGETHEFINISHOFYOURSTOVE. Spraycantouch-upsshould
be done only with a high temperature stove paint (cat. no. 70K99), avail-
able from all Lennox Hearth Products dealers.
CREOSOTE FORMATION AND NEED FOR REMOVAL
When wood is burned slowly, it produces tar and other organic vapors,
which combine with expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire. The chimney and
chimney connector should be inspected at least once monthly during
the heating season to determine if a creosote buildup has occurred. If
creosote has accumulated, it should be removed to reduce the risk of
a chimney fire.
BURN-IN PERIOD
ASH DISPOSAL
Pleasebepatientwiththeheatoutputofyourstoveforthefirstfewweeks.
The steel will go through a curing processthat eliminates moisture, which
is deep in the steel and firebrick. This moisture will reduce initial heat
output of your stove and may make it difficult to start. After you have
broken in the paint on the stove it will be necessary to build hot fires to
thoroughly remove the moisture from the appliance. Running the stove
with the draft fully open for 1 to 1-1/2 hours after starting and adding
generous amounts of fuel during the first week or two should complete
the curing process. We recommend the use of a thermometer attached
to the stove top or chimney. Temperatures on the connector pipe should
run in the 250-600 degree range. (DO NOT OVERFIRE THE STOVE
DURING THIS PROCESS. IF THE STOVE OR CHIMNEY BECOMES
RED, REDUCE THE AMOUNT OF AIR ENTERING THE STOVE
IMMEDIATELY).
Ashes should be scooped out of a cool stove with a small metal shovel.
Ashes should be placed in a metal container with a tight fitting lid. The
closed container of ashes should be placed on a non-combustible floor
or on the ground, well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed container until
all the cinders have thoroughly cooled. Ashes can ignite up to 72 hours
after removal from the stove.
FUEL
This unit is designed and engineered to burn, dry, well-seasoned wood
only.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Approved Chimney* - Your stove is approved for use with Class A, UL
103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type and Building
Heating Appliance Chimney (HT chimney - 2100° Fahrenheit) and double
wall connector pipe from Security™ Chimneys.
CLEARANCES TO COMBUSTIBLES
WARNING: BE ABSOLUTELY SURE THE DISTANCE BETWEEN
THE HEATER AND THE SURFACE OF ANY COMBUSTIBLE CON-
STRUCTION IS NOT LESS THAN SHOWN IN THE DIAGRAMS
ON PAGE 7.
Clearancestoconnectorshallbemeasuredfrom8"fluecollar.Restrictions
apply! Read instructions before installing.
Floor Protection
Chimney and Connector
USA - The floor in front and under the heater must be protected with a
minimumof3/8”thicknoncombustiblematerial.Thecoveringmustextend
16” in front of the door opening of the heater and 8” to either side of the
door opening and 5-1/2” to the rear or to the wall, whichever is smaller.
In all installations a 16” minimum hearth extension (in front of the stove)
is required as measured from the door opening of the unit.
Minimum 6" or 8” diameter, minimum 24 MSG black steel connector
pipe with listed factory-built chimney suitable for use with solid fuels or
masonrychimney.Horizontalconnectionnottested,refertolocalbuilding
codes for installation. May be installed with 6” connector pipe and Class
“A” chimney utilizing a 8” to 6” reducer. See installation instructions for
details. Read instructions before installing.
Canada - The floor in front and under the heater must be protected with
a minimum of 3/8” thick noncombustible material. The covering must
extend 457 mm in front of the door opening of the heater and 200 mm
to either side of the stove body and 200 mm to the rear or to the wall,
whichever is smaller. In all installations a 457mm minimum hearth
extension (in front of the stove) is required as measured from the door
opening of the unit.
The Legacy™ S260 may be installed using 6” chimney in vertical instal-
lations utilizing a 8” to 6” reducer (cat. # 71134) at the flue collar. If the
venting system is all vertical and the total vent length above the flue outlet
exceeds 14 feet, it is recommended that the 8” to 6” pipe reducer is used
and a 6” venting system be installed.
All of the stove connector pipe used must be of the same brand. The
chimney that the stove pipe transitions into may be a different brand.
Other than the transition of the stove pipe into the chimney, do Not mix
different brand vent components. Install all vent components per vent
manufacturer’s instructions.
Reduced Clearances
Clearances to combustible surfaces can be reduced with the use of listed
double wall connector pipe. See the clearances with double wall pipe on
the following page.
The chimney connector shall not pass through an attic or roof space,
closet or similar concealed space, or a floor, or ceiling. Where passage
through a wall, or partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365.
Alcove Clearances
Theremustbeaneffectivevaporbarrieratthelocationwherethechimney
or other component penetrates to the exterior of the structure. Follow the
vent manufacturer's detailed instructions.
Double Wall 8”/ꢀ0ꢁ mm Diameter - Minimum 64” (1626 mm) width,
maximum 48” (1219 mm) depth. Minimum 84” (2134 mm) height.
Double Wall ꢄ”/1ꢃꢀmm Diameter - Minimum 54” (1372 mm) width,
maximum 48” (1219 mm) depth. Minimum 84” (2134 mm) height.
IMPORTANT NOTE: See Draft Requirements and Selecting a Proper
Venting System on Page 4 to assist you in choosing the proper venting
system for your installation.
Mobile Home Installations
This appliance is approved for installation into a mobile home
in the USA ONLY!
Components Required For Installations
Pedestal Base or Legs.
Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title ꢀꢂ CFR, Part ꢁꢀ80 (in
Canada CAN/CSA Zꢀꢂ0 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
Aꢀꢀꢃ.1.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive rear
wall temperatures will result if the stove is burned without the
cover plate. Note: The cover plate is not necessary if a blower
has never been installed because a knock-out will be in place
to act as the cover.
All mobile home installations require an outside air kit (Cat. No. 71111 for
unitswithlegsorCat. No. 71112forunitswithapedestal). Thestovemust
be bolted to the floor and grounded to the chassis of the mobile home.
* Other approved chimney brands are Projet, Jakes Evans/GSW, Dura-
vent, Metal Fab, Ameri-Tec, Metalbestos and Industrial Chimney (ICC).
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A MOBILE
HOME.
CAUTION: THESTRUCTURALINTEGRITYOFTHEMOBILEHOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION CLEARANCES - REFER TO DIAGRAMS A, B AND C
PIPE
INSTALLATION
A
18”
(ꢂꢃ0mm)
B (1)
1ꢃ-1/ꢀ”
(ꢁ9ꢂmm)
C
ꢀꢄ”
(ꢄꢄ0mm)
D (1)
1ꢄ”
(ꢂ0ꢄmm)
E†
8”
ꢀ00mm
F (1,ꢂ)
11”
(ꢀ79mm)
G (ꢂ)
ꢀ1”
(ꢃꢁꢁmm)
H (ꢀ)
USA-ꢁ7-1/ꢂ”
CAN-1ꢀ00mm
ꢄ” Single Wall Residential
ꢄ” Double Wall Residential or Alcove
1ꢀ”
(ꢁ0ꢃmm)
9-1/ꢀ"
(ꢀꢂ1mm)
ꢀꢁ”
(ꢃ8ꢂmm)
1ꢁ”
(ꢁꢁ0mm)
8”
ꢀ00mm
11”
(ꢀ79mm)
ꢀ1”
(ꢃꢁꢁmm)
USA-ꢁ7-1/ꢂ”
CAN-1ꢀ00mm
or Mobile Home
*
8” Single Wall Residential
ꢀꢁ”
(ꢃ8ꢂmm)
ꢀ0-1/ꢀ”
(ꢃꢀ1mm)
ꢀ8”
(711mm)
18”
(ꢂꢃ0mm)
8”
ꢀ00mm
1ꢁ”
(ꢁꢁ0mm)
ꢀꢁ”
(ꢃ8ꢂmm)
USA-ꢁ7-1/ꢂ”
CAN-1ꢀ00mm
8” Double Wall Residential or
Mobile Home*
1ꢄ”
(ꢂ0ꢄmm)
1ꢁ-1/ꢀ”
(ꢁꢂꢁmm)
ꢀꢃ”
(ꢄꢁꢃmm)
1ꢃ”
(ꢁ81mm)
8”
ꢀ00mm
1ꢀ”
(ꢁ0ꢃmm)
ꢀꢀ”
(ꢃꢃ9mm)
USA-ꢁ7-1/ꢂ”
CAN-1ꢀ00mm
8” Double Wall Alcove - Residential
1ꢄ”
(ꢂ0ꢄmm)
ꢀ8”
(711mm)
ꢀ8”
(711mm)
18”
(ꢂꢃ0mm)
8”
ꢀ00mm
N/A
N/A
USA-ꢁ7-1/ꢂ”
CAN-1ꢀ00mm
or Mobile Home
*
PIPE
ꢄ” Single Wall
INSTALLATION
Residential
I
(ꢄ)
J (ꢀ)
USA-ꢁ7-1/ꢀ”
CAN-1118mm
K
L (ꢃ)
USA-0”
CAN-ꢀ00mm
M
N/A
T
(ꢄ)
USA-ꢃꢀ-ꢁ/ꢂ”
CAN-1ꢁ91mm
USA-1ꢄ”
CAN-ꢂꢃ0mm
USA-ꢄꢄ”
CAN-17ꢀ7mm
ꢄ” Double Wall
8” Single Wall
8” Double Wall
Residential or Alcove
USA-ꢂꢄ-ꢁ/ꢂ”
CAN-1ꢀꢁ8mm
USA-ꢁ7-1/ꢀ”
CAN-1118mm
USA-1ꢄ”
CAN-ꢂꢃ0mm
USA-0”
CAN-ꢀ00mm
8ꢂ” ꢀ1ꢁꢂMM
USA-ꢄꢄ”
CAN-17ꢀ7mm
or Mobile Home
*
Residential
USA-ꢃ7-ꢁ/ꢂ”
CAN-1ꢃ18mm
USA-ꢁ7-1/ꢀ”
CAN-1118mm
USA-1ꢄ”
CAN-ꢂꢃ0mm
USA-0”
CAN-ꢀ00mm
N/A
N/A
USA-ꢄ8-ꢁ/ꢂ”
CAN-1797mm
Residential or
Mobile Home*
USA-ꢃ0-ꢁ/ꢂ”
CAN-1ꢁꢂ0mm
USA-ꢁ7-1/ꢀ”
CAN-1118mm
USA-1ꢄ”
CAN-ꢂꢃ0mm
USA-0”
CAN-ꢀ00mm
USA-ꢄ7-1/ꢂ”
CAN-17ꢃ9mm
8” Double Wall
Alcove - Residential
or Mobile Home
*
USA-ꢃ0-ꢁ/ꢂ”
CAN-1ꢁꢂ0mm
USA-ꢁ7-1/ꢀ”
CAN-1118mm
USA-1ꢄ”
CAN-ꢂꢃ0mm
USA-0”
CAN-ꢀ00mm
8ꢂ” ꢀ1ꢁꢂMM
USA-ꢄ7-1/ꢂ”
CAN-17ꢃ9mm
† USA=8" (ꢀ00mm) from door opening, Canada=8" (ꢀ00 mm) from sides and back of unit
u
Dimensions to Stove Body
* Mobile Home - USA only
Diagram A: Top View-Parallel Installation
Diagram B: Side View-Alcove and Parallel Installations
ꢂ8”
B
A
L
Footnotes:
Max.
C
D
Depth
1- These dimensions to the stove body are for
reference only. Actual distances should be
measured from the stove’s flue collar.
2- Minimumnoncombustiblehearthpaddimen-
sions.
8” Ø
Flue Collar
I
H
96” Min.
M
3- Shield shall be attached to the rear of the
stove pipe with a 1” air space and must run
from the top of the stove to the ceiling.
4- Not applicable to alcove installations.
5- In corner applications, when installed at
minimumbackwallclearances,therequired
floor protection is dimensioned off the
back plane of the stove, therefore the floor
protection required off the back corners (at
a 45 degree angle) only needs to extend to
the wall. This situation will only occur in
CANADA installations.
†E
†E
Floor Protector
K
J
Floor Protection
I
G
G
F
F
T
6- Reference dimension only, to assist in plan-
ning the installation.
H
Diagram C: Top View
Corner Clearance,
Stove and Flue to Wall
Clearances to connector pipe shall be mea-
sured from the flue collar of the stove.
Floor
Protection
K
J
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. First, screw the threaded rods into the holes at the four corners on the
bottom of the stove. Screw the threaded rods into the firebox three
full rotations or 3/16” to 1/4” (if the rear rods are screwed in too far
they will lift the bricks off the bottom of the stove). Use a washer
and nut to secure the leg. Be sure the legs are mounted squarely on
the firebox bottom. Tighten nuts securely.
LEG AND HEATSHIELD INSTALLATION
Residential and Mobile Homes - Bolting down and grounding of stove
are required only in mobile homes.
4. Use the two bolts and washers provided with the heatshield kit to
mount the heatshield as shown in Figure 3.
5. Do not over tighten the heatshield mounting bolts as it may bend the
heatshield.
Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
Leg Installation
OUTSIDE AIR KIT INSTALLATION
1. Carefully place stove on its back. Be careful not to scratch the stove,
use a piece of cardboard or carpet to protect the back of the stove.
2. Mount all four legs as shown in Figure 2.
To install the “Outside Air Kit”, position the clip so that the nut is directly
above the hole punched in the back of the heatshield (see Figure 4).
Install the outside air adapter box on the stove by sliding it into the air
channellocatedbetweenthebottomheatshieldandthestovebottomuntil
the oblong ring is approximately 1/4” from the rear edge of the lower
heatshield. Make sure the ring is facing down. Thread the bolt up through
the nut in the clip until snug against the adapter box.
Threaded Rod
Expanded View
of Clip
Washer
Nut
Line up the hole in the clip with the hole in the
rear center of the bottom heatshield
Figure 2
Clip
1/ꢂ” Bolt
Figure 4
BACK
To locate the hole in the hearth for outside air, mark a 4” circle on the
hearth. The circle’s center should be 2-3/4” directly back from the center
of the flue outlet and 5/8” to the left side.
Heat Shield
Mounting Holes
FRONT
Air Channel
Figure 3
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Download from Www.Somanuals.com. All Manuals Search And Download.
14. All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot.
The connector pipe must meet minimum clearances in any direction
to walls or other combustible materials. It must attach to a listed
double wall metal chimney at least 6” in diameter or to a masonry
chimney with a flue passage of at least 48 square inches.
15. It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use. Install connector at
no less than the minimum clearances from the ceiling when using
a 90-degree elbow to pass through combustible constructions.
16. Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufactures
directions. NFPA No. 211 gives approved methods for passing a
flue pipe through combustible constructions.
STOVE INSTALLATION
1. If not previously installed, install floor protection and move the
heater into the desired location.
2. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances are
met.
3. If you are installing outside air on your stove, mark a 4” circle on
the floor protection just below the oblong ring. When cut out, this
hole will accommodate the flexible outside air tube.
4. If the stove is to be fastened to the floor, locate the hold down
brackets inside the leg box and mark the floor protection below the
holes in the brackets.
5. If you are installing outside air on your stove, remove the stove and
cut the floor protection and the floor where the 4” air tube circle had
been previously drawn. If the stove is to be fastened to the floor,
drill 1/2” holes through the floor protection only, at the marks that
were for fastening the stove to the floor if so desired. Slip the flexible
outside air tube through the hole in the floor, leaving 1” of tube above
the floor protector surface, using tape to hold it in place.
6. Place the stove on the floor protection so that the previously cut or
drilled holes line up. Attach the stove to the floor with the lag bolts
if so desired.
7. If you are installing outside air on your stove place the hose clamp
over the flexible air tube and slide the tube up over the 4” ring on
the outside air adaptor box and tighten the hose clamp. Push the
outside air adaptor forward 1/4” until full contact is made with the
lower heatshield. Tighten the 1/4” bolt until the adaptor box is held
firmly in place. Use silicone sealant to create a seal between the
flexible air tube and your floor protection.
8. If it is necessary to level, secure, or ground your stove, use the holes
in the bottom of the leg for those applications. To level the stove
on Olympic cast legs, locate the front leg that is not touching the
hearth pad. Insert the allen head screw through the slotted washer
(supplied with the legs) and into the threaded hole in the bottom of
the leg. See the drawing to the right. Push the slotted washer down
until it touches the hearth pad and then tighten the screw into the
leg. Should any other leg not be resting on the hearth pad, install a
washer and screw in that leg as well.
9. Install bricks and baffle as per instructions on Page 12. It is highly
recommended that the baffle be assembled before the chimney is
installed so that the baffle blanket can be adjusted into place through
the flue collar.
Insert the allen
head screw
through the
slotted washer
10. If installed into a mobile home, the stove shall be grounded to the
mobile home chassis with a #8 AGW copper wire or equivalent.
11. For residential installations, install the first section of stove pipe
with the crimped end going down inside the flue collar on the heater.
Continue with your stove pipe, installing each section-crimped
end down. Make the final connection to your chimney. Your dealer
carries the necessary pipe and fittings to connect to the various
listed factory-built chimneys. YOUR CHIMNEY INSTALLATION MUST
COMPLY WITH LOCAL BUILDING AND FIRE CODES.
Figure 5
12. Be sure to fasten each stove pipe connection with at least 3 sheet
metal screws.
13. Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If required, install the Outside Air Kit (cat. no. 71112) as per the
following instructions. To locate the hole in the hearth for outside
PEDESTAL INSTALLATION
air mark and cut a 4” (102 mm) hole in the hearth. The hole’s center
(For ash drawer pedestal see instructions included with pedestal)
Residential and Mobile Homes
should be 3” (76 mm) directly forward from the center of the flue
outlet or locate as per the instructions below.
6. Position the stove on your floor protection in the exact location where
it is to be located, making sure all minimum clearances are met. Mark
the floor protection where the pedestal will be located, then remove
the stove.
(Bolting down and grounding are required only in mobile homes)
CAUTION: Wear gloves during installation in case of sharp edges on
the stove.
7. Make four 1-1/2” (38 mm) cuts in one end of the corrugated tube and
fold the flaps back. Cut a 4” (102 mm) hole through the floor protec-
tion and the floor and insert the corrugated tube into the hole. Cover
it with the supplied screen and fasten it to the floor protector.
1. Remove the heater from the carton, if packaged, upon receipt and
check for any damaged or missing parts.
2. Carefully put the stove on pedestal with the open end of the pedestal
facingtherear.DONOTLEAVETHESTOVEUNATTENDEDUNTIL
IT IS BOLTED SECURELY TO THE PEDESTAL.
8. Locate the 1-1/2” x 14” (292 mm x 356 mm) metal plate and paint to
match the stove if necessary. Position this piece so that the 14” (356
mm) dimension evenly overlaps the lips on the back of the pedestal
(see drawing below). Attach this plate to the back of the pedestal with
the self-tapping screws supplied.
3. Line up the holes in the brackets on the pedestal with the threaded
holes in the bottom of the stove and use the two 1/2” long bolts AND
3/8” standard washers to bolt the stove to the pedestal. Be sure to
see that the stove is mounted squarely on the pedestal before
tightening the two bolts securely.
4. When installing a pedestal on this stove you MUST plug the four leg
mounting bolt holes, located on the bottom of the stove in the four
corners, with the bolts that were used to mount the shipping legs. The
two rear bolts should not be installed more that two full rotations
to prevent lifting the bricks off the bottom of the stove. FAILURE
TO INSTALL THESE FOUR BOLTS PROPERLY WILL RESULT
IN REDUCED CONTROL OF THE STOVE’S COMBUSTION
SYSTEM!
9. If the stove is to be fastened to the floor, attach the stove with the
supplied lag bolts, through the pedestal base on opposite sides,
attaching them into the floor beneath the floor protection. Seal any
irregularities with silicone sealer.
10. If installed in a mobile home, the heater shall be grounded to the
chassis with a #8 AGW copper wire or equivalent.
11. InstallbricksasperinstructionsonPage12.Itishighlyrecommended
that the baffle be assembled before the chimney is installed so that
the baffle blanket can be adjusted into place from the flue outlet.
12. Install chimney as per manufacturer’s instructions.
Block Off Plate is
Required When
Installing Outside
Air Into Unit (Plate
is Included With
Kit # 7111ꢀ)
Figure 6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR OWN PROTECTION AND INSURANCE PURPOSES,
HAVE YOUR CHIMNEY AND CONNECTOR PIPE INSTALLATION
INSPECTED BY YOUR LOCAL BUILDING CODE AUTHORITY OR
FIRE MARSHAL BEFORE STARTING A FIRE IN YOUR STOVE.
NOTIFY YOUR INSURANCE COMPANY.
POST INSTALLATION CHECKS
1. Check that all chimney pipe joints are securely fastened.
2. Check that the heater is securely fastened to the floor (if
applicable).
3. Make sure the intake vent has clear access to outside air (if
applicable).
4. Make sure the outside air vent has been sealed properly to keep
rodents out (if applicable).
5. Be sure all roof flashings are watertight.
6. Be sure the stove is properly grounded (if applicable).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: IF THE BRICKS ARE NOT INSTALLED EXACTLY AS
SHOWN, THEY COULD FALL OUT OF PLACE DURING RE-
FUELING OR BURNING OF THE STOVE, CAUSING SERIOUS
INJURY.
BRICK INSTALLATION
CAUTION: Wear gloves during brick installation in case of
sharp edges inside the stove.
Note: Installation of the baffle boards and insulating blanket is easier
when you can still access the flue outlet (before connecting flue vent).
Be sure the baffle blanket is placed flat on the baffle boards so as
not to block exhaust flow to the flue. Use a ruler or piece of kindling
to reach over the baffle blanket to be sure it is completely flat on top of
the baffle bricks.
Legacy™ Sꢀꢄ0 Brick Sizes
(see Figures on this page)
A = ꢂ-1/ꢂ” x 9”
D = ꢀ-1/8” x ꢄ-1/ꢂ”
E - 1-ꢁ/ꢂ” x 9”
F = ꢂ-1/ꢀ” x 9”
G = ꢀ-1/8” x ꢂ-1/ꢂ”
H = ꢂ-1/ꢂ” x ꢂ-1/ꢀ”
S = ꢀ-1/8” x 9”
1. Install bricks #1-28 in the numbered sequence shown in Figure 7.
2. Next, you will install the rear baffle boards which are the smaller two
of the four baffle boards. The boards will be installed with the 5-1/2”
dimension from the front to the rear of the firebox. These boards
will be placed on the top side of the rear baffle just to the rear of the
middle secondary tube, you will push the baffle boards towards the
rear of the firebox until they fall in place at the rear side of the middle
secondary tube. You will place one board to the far left side of the
firebox and one board to far right side of the firebox. Confirm that
both boards are laying flat on the rear baffle and that they are not
overlapping each other.
3. Next, you will install the baffle blanket. It will be installed with the
15-1/2” dimension from the front to rear of the firebox. Install by
lifting it into place between the front and rear baffle. Place the blanket
over the rear baffle and rear baffle boards that you have just installed.
Next you will place the baffle blanket that is protruding beyond the
front side rear baffle on the top side of the front baffle.
Baffle
Insulation
Parts
ꢀꢀ-1/ꢀ”
1” Thickness
Baffle Blanket
1ꢃ-1/ꢀ”
4. The final step of the baffle board & baffle blanket installation will be
installing the front baffle boards. The front baffle boards will be the
two remaining baffle boards which are the larger two baffle boards
of the four baffle board kit. They will be installed with the 9-5/8”
dimension from the front to rear of the firebox. Start by setting the
back side of the board on the rear baffle making sure that it is placed
far enough back to lift up and onto the front baffle. Next you will place
the front edge of the front baffle boards on the top side of the front
baffle and slide them towards the firebox front until it stops against
the front baffle edge. You will do this with each front baffle board
with one to the right side of the firebox and one to the left side of
the firebox. Confirm that the baffle blanket is directly on top of the
baffle boards and that it does not protrude beyond the front baffle
or front baffle boards as shown in Figure 9.
11-1/ꢂ”
1/ꢀ” Thickness
Front Baffle Boards
(ꢀ included)
9-ꢃ/8”
11-1/ꢂ”
1/ꢀ” Thickness
Rear Baffle Boards
(ꢀ included)
ꢃ-1/ꢀ”
Figure 8
Firebrick Diagram
22
S
23
G
24
S
Side Cut-A-Way View of Firebox
S*
29
25
S*
D
5
F
3
4
F
2
F
1
F
28
A
Front Baffle
Boards
Baffle Blanket
6
10
F*
F*
7
F
11
F
8
F
12
F
18
F
14
F
17
15
16
A
9
E
F
F
13
E
0
.
0
2
4
6
8
0
.
0
.
0
.
.
1
.
0
19
F
21
20
H
F
Rear Baffle
Boards
Front View
See the following for brick sizes
Firebox
Brick
*Fits against the back of the firebox.
Note: These bricks may be slightly smaller to adjust for steel and
firebrick tolerances beyond our control. Be sure to measure and
mark bricks with their numbers when removing.
Figure 9
Figure 7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING HINTS
STARTING AND MAINTAINING A FIRE
Be sure to clean the Nickel or Gold Plated door with a house-
hold type glass cleaner and a very soft cloth to remove any
fingerprints and residues prior to the first fire.
1. Burn only dry, well-seasoned wood for maximum heat output. In some
states it is illegal to burn wet wood or anything other than clean, dry
wood products.
2. Your stove is designed to operate with the door closed! Operate only
with the door shut tightly at all times except when loading wood and
possibly on start up to establish a draft. Never leave the unit unat-
tended while the front door is slightly opened.
1. NEVER USE FLAMMABLE LIqUIDS TO START OR REKINDLE
A SOLID FUEL FIRE!!
3. DO NOT hit or move the baffle board while loading wood. Occasionally
check the baffle. Make sure the baffle blanket is always flush with the
front of the baffle boards. Loading oversized logs may dislodge the
baffle boards.
4. CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN BE-
FOREOPENINGTHEDOORTOAVOIDPOSSIBLECOMBUSTION
FLASH!! (Ignition of hot volatile gases as the door is opened).
5. Feeding excessive amounts of fuel to the stove should be avoided.
It is important to supply it with sufficient draft and fuel to maintain a
moderatelyhotfire.If,duringovernightburns,heavycreosotedeposits
develop inside your stove and on the door, the draft is set too low
- review your burning habits!
2. Fully open the primary draft control by pulling the 1” plastic knob
out on the left side (lower front corner) until it stops (away from the
stove). This control determines the amount of air entering the stove.
Pushing it toward the stove reduces the burn rate in the firebox. For
yourconvenience, therodonthiscontrolismarkedwithfourgrooves
to assist you in obtaining repeatable burn rates.
3. Place a small amount of crumpled paper in front of the firebox and
cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling to become
fully engulfed in flames. You will now close the wood units front door.
(Your wood units front door may or may not need to be left slightly
open during this start up process, this depends on the stove model
and the amount of draft present. Do not leave the unit unattended
while the front door is slightly open) Once kindling is burning well,
larger pieces of wood may be added, then the door should be fully
closed if there was the need to keep it slightly open during start
up.
CAUTION
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replace-
ment parts.
Donotoperatethestovewiththedooropenorajarotherthan
possibly during start up to create a draft (Do not leave the
unit unattended while the front door is slightly open during
start up). Operating the stove with the door open other then
in initial start up if needed will produce extreme tempera-
tures within the stove. Damage caused from over-firing is
not covered under the manufacturers limited warranty.
OK
5. For best results, use smaller pieces of wood to get the insert tem-
perature very high before loading larger wood for sustained burns.
If necessary, crack the door to allow ignition of the fuel charge. Do
not leave the unit unattended while the front door is slightly open.
Now you can add larger pieces of wood and after several minutes of
high burn, set the left control for the desired heat output. Check the
exhaust in about 15 to 20 minutes. Large amounts of smoke indicate
an improper burn setting (either too high or too low). Adjust and
recheck in 5 to 10 minutes.
Figure 10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER OPERATION
Blower Operation
The blower can be operated manually or automatically (blower will
turn on when the stove is hot and turn off when the stove is cool).
The rocker switch on the control panel allows you to select between
manual operation or automatic operation as follows (see Figure 12):
MANUAL OPERATION: Turn rocker switch to the “MANU-
AL” position and adjust rheostat knob to the desired speed. The blower
will have to be manually turned “OFF” by rotating the rheostat knob
clockwise until it clicks.
Blower Speed Control
Knob (rheostat)
Manual / Auto
Rocker Switch
Figure 12 - Blower Controls
AUTO OPERATION: Turn rocker switch to the “AUTO” posi-
tion and the rheostat to the ON position (rotate rheostat knob coun-
terclockwise until it clicks). When the stove warms up, the blower will
automatically turn on (adjust rheostat knob to the desired speed set-
ting). When the stove cools down, the blower will automatically turn
off.
WARNINGS
The blower must be plugged directly into a properly
groundedthree-prongreceptacle,1ꢀ0VAC,ꢄ0Hz,single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Rheostat Operation - The highest blower speed is obtained by turn-
ing the rheostat knob counterclockwise until it clicks “ON”, then rotate
towards “HIGH” to increase blower speed. Rotate the knob clockwise
for a lower speed. To turn off, continue to rotate the knob clockwise
until it clicks “OFF.”
Installation must be in accordance with National Elec-
trical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA Cꢀꢀ-1 Canadian Electrical Code - latest
edition.
Blower Operation Guidelines
While in auto operation mode, the blower will turn off and on based on the
temperature of the stove. Auto operation ensures there is sufficient heat
build-up to warm the air being moved by the blower before the blower is
turned on. Likewise, when the stove cools off, the blower is turned off
to prevent circulating cool air. Depending on the size and intensity of the
fire it may be necessary to adjust the fan speed accordingly to ensure un-
interrupted fan operation. For example a small fire may require a slower
fan speed to keep the heat output by the fan consistent. If the blower is
operated in manual mode, it may be necessary to adjust the blower speed
as the fire begins to burn down and the stove is no longer hot enough to
effectively heat the air moved by the blower. If the air coming from the
blower feels cool, one should either decrease the blower speed or stoke
the fire to build up more heat.
DANGER: Disconnect power before servicing blower.
In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox Hearth
Products)isinstalledbeforeusingtheheater.Excessive
rear wall temperatures will result if the stove is burned
withoutthecoverplate. Thecoverplateisnotnecessary
ifablowerhasneverbeeninstalledbecauseaknock-out
will be in place to act as the cover.
AUTO-RESET
TEMPERATURE
ROOM AIR
SWITCH N/O
BLOWER
TWO POSITION
SWITCH
MANUAL/TEMPERATURE
NOTE: SWITCH CONDITIONS
GIVEN AT ROOM TEMPERATURE
N/C = NORMALLY CLOSED
N/O = NORMALLY OPEN
3-RED
1-BRN
3-RED
YLW
= FEMALE DISCONNECT
= MALE DISCONNECT
= STUD CONNECTION
3-RED
1-BRN
WHT
SPEED
CONTROL/OFF
POWER CORD
4-GRN
4-GRN
BLK
Figure 11 - Blower Wiring Schematic
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING TECHNIqUES AND HINTS
ACHIEVING CLEAN, LONG BURNS
Recentdevelopmentsinwoodburningtechnologyhavemadewoodburning
a cleaner and more convenient way to heat your home. Overall efficiency
in a wood burning appliance is a combination of combustion efficiency
and heat transfer efficiency. Whether heating your entire home, or just a
room or two, your understanding of how to best operate your stove or
insert will enhance its overall efficiency and performance. What this can
mean to you is longer, cleaner burns, less wood use and more heat.
To achieve long burn times, after having thoroughly preheated the
stove, let the stove top cool down to ꢀ7ꢃ to ꢂ00 degrees (on Elites,
locate thermometer on the face of the insert just above the door). Now
load the firebox and set the draft control. At this point, you may need to
burn the stove with the draft open for a few minutes to ignite the wood.
All Country Collection stoves are EPA tested for emissions at low burn
with the air control completely closed. Whether or not you should burn
your stove with the air control completely closed will depend on the
following factors.
GETTING THE MOST OUT OF YOUR STOVE
The following sections will outline techniques you can use to “get the
most out of your stove.” Please read them carefully.
* How you load your wood
* Your chimney type, height and draft
* Your wood type and its moisture content
* The temperature of the stove
* Which model stove or insert you have
MAXIMIZING YOUR STOVE’S OVERALL EFFICIENCY
Experiment with different loading configurations to achieve longer
burns. Try loading the wood from side to side and nesting it in the ashes
to prevent airflow under and around the wood. Fresh wood should be
loaded to the back of the firebox or to the sides. Hot coals or half burned
wood should be brought towards the front of the firebox. The way you
load your wood can seriously affect burn times. If the new load does not
ignitewithinafewminutes,trycrisscrossingtheloadtoallowmoreairflow
around the fire, or try a slightly hotter stove temperature.
It is important to know that for high, combustion efficient, clean burns,
you will need to have sufficient temperatures inside the firebox for
thorough combustion. The best method for determining if you have
sufficient temperatures is to watch the brick lining in your firebox. When
you first light your stove, the bricks will turn a dark brown or black.
After 20 to 30 minutes of a hot fire, most of the bricks should return
to near their original light brown or yellow color. This means the bricks
have reached a high enough temperature for your stove to achieve high
combustion efficiency.
Determining the lowest setting for efficient low burns. This will require
some experimentation on your part. Try closing the air control all the
way with the stove temperature at 325 to 350 degrees. If the flames are
completely extinguished, open the air control halfway and then slowly
close it until there is only a small amount of flame. It is important to check
the stove about 20 minutes after setting the draft control as it takes this
long for the stove temperature to stabilize. There should still be some
small flames on or above the wood load.
Second and just as important, is achieving a high level of heat transfer
efficiency. Slowing the rate of flow through the stove or insert enhances
heat transfer, thus allowing more time for heat to be transferred into
your home. To do this, be sure to thoroughly preheat your stove and
then reduce the amount of primary air by closing the draft control (lower
left) to about 1/2 to 3/4 open. This will decrease the excess oxygen in
your flue, which carries heat up your chimney, but should still be enough
air to allow the stove to produce its maximum heat output. (More air
may produce a slightly greater amount of heat, but will greatly increase
wood consumption). When the area being heated reaches a comfortable
temperature, slow the burn rate by closing the control to further improve
heat transfer.
Use ꢁꢀꢃ degrees as a starting point. You can try starting temperatures
25degreeshigherorlowertoachievedesiredburntimes, start25degrees
lower if the stove burns the wood too quickly or 25 degrees higher if there
are no flames in the firebox for more than a few minutes after loading the
wood. You may or may not need to burn the stove with the air control
open for a few minutes prior to setting the draft for a low burn, this will
depend on the factors mentioned above. Be sure not to smolder a fire
overnight. Check your chimney for large amounts of smoke as this
indicates very poor combustion.
To get the most out of your Country™ Collection stove, you will need to
combine good combustion efficiency with good heat transfer practices.
The following are some tips on how to operate your stove to achieve the
highest overall efficiency:
It is important to realize that stove technology has changed. Stoves
have changed a great deal in the last few years. This has led to substantial
changes in the methods of operation in new stoves as compared to older
stoves. In old stoves without full brick linings and ceramic insulation,
the rule was “get the stove as hot as possible before setting the draft on
low for overnight burns.” On newer, high technology stoves, this is not
necessary. Although it is still important to have the stove hot enough to
burn efficiently, it will require less preheating. Once you have determined
your optimum operating temperatures for various burn rates, we believe
you will find your stove an extremely convenient way to achieve your
heating needs.
1. Thoroughlypreheatyourstovebeforeslowingtheburnratebyclosing
the draft control.
2. Measure the stove temperature at the hottest point on the stove top
or face. Use this information to repeat burn rates.
3. Once preheated, add wood (if needed) and partially close the draft
control (lower left).
4. Operate your stove as much as possible in the low to medium burn
ranges.
5. Do not lower the draft setting so low as to completely extinguish the
flames in the firebox. Check for at least some small flames twenty
minutes after setting the draft control.
6. Do not continually operate your stove in the high (wide open) setting.
This wastes wood by carrying a great deal of heat up the chimney
and can damage your stove and chimney.
7. Go outside and check your chimney. More than a very small amount
of smoke indicates wasted heat, creosote build-up and pollution.
Do not reload the stove for long burns when the stainless secondary
tubes or baffles are glowing red, or when the stove is uncomfortably
hot to load. This indicates the stove is too hot to load for a long burn.
Also, do not load wood for a long burn on a deep bed of hot coals. Try
stirring the coals a few minutes before loading the stove for a low burn
to allow some of the unburned coals time to burn.
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEANING GLASS
DOORHINGES: Ifdoorhingesneedlubricating,useananti-seizecompound
(never use oil) available from your Lennox Hearth Products dealer.
SEE MAINTENANCE FOR GLASS CLEANING TIPS
The operator plays an important part in keeping the glass clean and free
of build-ups. The first and most important part the operator plays is mak-
ing sure to burn only well-seasoned firewood. Wet wood = Dirty glass.
Keeping your glass door clean is partly accomplished by the air wash
system of the stove, which sends clean, fresh air for combustion, over
the window before it enters the fire. The high temperatures inside the
fireboxalsokeeptheglassclean.Nostovedoorstaysperfectlyclean.The
following are methods for keeping build-up on your glass to a minimum.
When properly installed and operated by a knowledgeable operator, your
glass door should require very little maintenance. Do not expect to get
extremely long burn times and keep the window perfectly clean. Cool
temperatures cause condensation of unburned volatiles on the glass. If
your glass gets very dirty during overnight burning, try preheating the
stove a little longer before damping it down for an overnight burn. Also,
don’t damper your stove down as low because you’ll get more heat for
your money by burning a little hotter for a slightly shorter time.
DOOR LATCH: If your door latch fails to latch tightly and the gasket is
in good condition, place a length of pipe (cheater bar) over the inside
portion of the door handle and bend slightly toward the door until the
proper adjustment is obtained. If the door handle does not close easily,
apply high temperature anti-seize to the striker.
DOOR GASKET: Periodically check gasket to make sure it is not over-
compressed. If compressed, replace with a special woven door rope.
(Don’t try substituting rope, only use special Lennox Hearth Products
door rope).
GOLD OR NICKEL PLATED DOOR: Clean only with a household type
glass cleaner and a very soft cotton cloth. Other products may damage
brass, paint and gaskets.
BAFFLE BLANKET: Your baffle blanket should be inspected during every
chimney cleaning. If the baffle blanket is compressed or heavily stained,
it should be replaced. Heavy creosote stains or matting is an indication
of improper use and your burning habits should be reviewed.
The air wash system will perform at its best at medium burn rates. Some
stove models will self clean by burning very hot fires but be sure not to
over-fire the stove. If it glows red it is over-fired. Over-firing a stove also
causes the window to soot up. Extremely hot fires with fresh wood may
cause the flow rate to exceed one foot per second, which is as fast as a
flame can burn. This is why a candle goes out when you blow on it. Blow
on it gently and it burns brightly. Blow on it hard and it goes out. This will
cause excessive exhaust emissions and your window to soot up, as the
stove is unable to burn the gases emitted from the wood. Try slowing the
stove down a little by closing the damper somewhat as it warms up.
GLASS CLEANING: Only clean glass with products specifically made to
use on wood stoves. Other products could damage gaskets and paint.
Never scrape glass with a razor blade. This can pit the glass and make it
impossible to clean in the future.
WINDOW GASKET: The window gasket can be checked by running the
flame of a match near the gasket and around the door. If the flame is
drawn in around the window, the gasket should be replaced.
Keeping freshly loaded wood away from the window will also help. Load
freshlogsintherearofthefirebox.Build-uptendstooccurfirstontheright
side of the window. This is caused by the swirling motion of the exhaust
gases similar to water running down a drain. Keep fresh logs further back
on the right side of the firebox to help prevent this problem.
DOOR HANDLE: Door handle may become tight as you use the stove.
Free the handle up by using dry graphite supplied with the stove. The
directions are included with the graphite.
Understanding how your Country™ Collection stove works should help
you keep your glass door very clean, but as stated: no glass door stays
perfectly clean. We hope this information is helpful in keeping your
glass door clean so that you may enjoy many hours viewing your high
efficiency stove. For more information, contact your Lennox Hearth
Products dealer.
WARNINGS
Inspectandcleanchimneyandconnectorfrequently.
Under certain conditions of use, creosote buildup
may occur rapidly.
CAUTION
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasivecleaners.Donotcleanwithanymaterials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.
1ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Solution
POOR DRAFT:
Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have
poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See Drafting section on
Page 4). If your stove is not drafting properly, your chimney is the problem. All stoves are thoroughly tested to ensure
proper draft with the correct size chimney flue.
EXCESSIVE DRAFT:
DIRTY GLASS:
With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by slowing the
burn rate of the stove once it has reached proper operating temperature (See Maximizing Your Stove’s Overall Efficiency
on Page 15).
1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft control.
2) Make sure your wood is well seasoned and dry (not open to rain - see Creosote and Fuel sections on Page 5).
3) See Poor Draft section (above) and Cleaning Glass on Page 16.
SMOKES WHEN
DOOR IS OPEN:
1) If smoke is entering the room, check to make sure your baffle boards are properly installed
and that the baffle blanket is pushed back flush with the front of the baffle boards.
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 5 and 6).
3) Check draft (See POOR DRAFT section above).
WOOD BURNS
TOO FAST:
1) The draft control must be closed further.
2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”
POOR HEAT
OUTPUT:
1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire. It normally
takes from one to three weeks of burning to season your stove (See Burn-In Procedures on Page 5).
3) See Excessive Draft section above.
PAINT GIVES OFF
ODOR (smoke):
Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See Burn-In
Procedures on Page 5).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DO’S AND DON’TS
DO NOT: Install or operate this stove before reading this manual.
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT: Open the stove door without fully opening the draft first.
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in salt water
on the way to the mill. (This will void your warranty).
DO NOT: Handle the Nickel or Gold faceplate unnecessarily. Use the door handle only.
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.
DO NOT: Close the door tightly during Burn-In Period.
DO:
Be sure to clean any fingerprints from the Gold or Nickel faceplate before burning the stove. Clean the Gold or Nickel door only with a
household type glass cleaner and a very soft cloth.
DO:
DO:
Consult local building department if other than recommended clearances are desired.
Read instructions for the baffle boards and baffle blanket occasionally to ensure you have not bumped or moved them out of place
when loading wood.
DO:
DO:
DO:
DO:
Check the chimney and baffle monthly to make sure they are clean.
Burn seasoned, dry wood only! (RAIN = WET WOOD)
Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.
Enjoy the warm feeling of your new Country™ Collection stove.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FSB BLOWER PARTS
Description
REPLACEMENT PARTS - MODEL Sꢀꢄ0
Item #
ꢀꢃ
Cat. No
H80ꢄꢀ FSB700 Blower Only Assembly w/ blower wiring
harness
Contact an Authorized Lennox Hearth Products dealer to obtain
any of these parts. Never use substitute materials. Use of
non-approved parts can result in poor performance and safety
hazards.
ꢀꢄ
ꢀ7
ꢀ8
ꢀ9
ꢁ0
ꢁ1
Hꢃꢄꢃ8 Fan Blade (FSB700)
Hꢃꢄꢃ7 Fan Cage (FSB700)
H80ꢄꢁ FSB700 Blower Only Wire Harness
H80ꢄꢂ Snap Switch w/gasket and screws
Hꢃ7ꢂꢀ Speed Control - High Temperature (FSB700)
FRONT DOOR PARTS LIST
Item #
Cat. No
Description
1
ꢀ
ꢁ
ꢂ
ꢄ
7
Hꢃꢄꢁ9 Door Rope Kit, 7/8” Dia. (ꢄ’ ꢀ”)
Hꢃꢄꢀ9 Upper Hinge Pin
H80ꢄꢃ Control Panel Assembly w/ Snap Switch Housing
Assembly
ꢁꢀ
H80ꢄꢄ Control Switch (Manual, Off, Automatic)
Sꢀꢄ0 STOVE PARTS
Hꢃꢄꢀꢄ Upper Hinge Pin E-Clip
Hꢃꢄꢀ8 Lower Hinge Pin
ꢁꢁ
ꢁꢂ
Hꢃꢄꢀꢄ Removable Inner Flue Collar Ring
H8079 Nameplate Kit w/ Hardware - Silver
H8080 Nameplate Kit w/ Hardware - Gold
Hꢃꢄꢃ0 Draft Rod Knob
Hꢃꢄꢂ0 Glass Gasket Kit (8’ ꢂ”)
Hꢃꢃ77 Set of ꢄ screws and ꢄ washers for door assembly
Hꢃꢄꢃꢂ Spring Handle / Nickel
Hꢃꢄꢃꢁ Spring Handle / Gold
8
ꢁꢃ
ꢁꢄ
ꢁ7
ꢁ8
ꢁ9
ꢂ0
ꢂ1
ꢂꢀ
ꢂꢁ
ꢂꢂ
ꢂꢃ
ꢂꢄ
ꢂ7
ꢂ8
H8081 Ash Block Off - Hearthplate
71099
71100
7109ꢃ
71097
71098
7108ꢀ
7108ꢁ
7108ꢂ
711ꢂ9
711ꢂꢄ
Traditional Door Glass / Plain
Hꢃꢄꢄ1 Cast Iron Ash Plug
Traditional Door Glass / Sailboat
Traditional Door Glass / Cattail
Hꢃꢃ8ꢀ 1/ꢀ Cut Brick for Ash Removal
Hꢃꢄ1ꢀ Firebrick ꢂ-1/ꢀ” x 9” (1ꢄ per stove)
Hꢃꢃ7ꢄ Firebrick ꢂ-1/ꢂ” x 9” (ꢀ per stove)
Hꢁ097 Firebrick ꢂ-1/ꢂ” x ꢂ-1/ꢀ” (1 per stove)
Hꢃꢄ11 Firebrick ꢀ-1/8” x 9” (ꢂ per stove)
Hꢃꢃ9ꢃ Firebrick ꢀ-1/8” x ꢄ-1/ꢂ” (ꢀ per stove)
Hꢁ09ꢂ Firebrick ꢀ-1/8” x ꢂ-1/ꢂ” (1 per stove)
Hꢃꢄ1ꢁ Firebrick 1-ꢁ/ꢂ” x 9” (ꢀ per stove)
Hꢃꢃꢄ8 Front Baffle/Secondary Burn Tube Assembly
Hꢃꢃꢄ7 Middle/Rear Baffle/Secondary Burn Tube Assembly
9
Traditional Door Glass / Evergreen
Traditional Door Glass / Floral
Traditional Door Faceplate / Black
Traditional Door Faceplate / Gold
Traditional Door Faceplate / Nickel
Traditional Door Faceplate / Brushed Gold
Traditional Door Faceplate / Brushed Nickel
10
11
Hꢃꢃꢄꢀ Traditional Door Back w/ Handle (door gasket
included)
ASH DRAWER PEDESTAL & PEDESTAL
Hꢃꢃ1ꢂ Small & Large Pedestal Rear Block Off Plate w/ Hole
Hꢃꢃꢃꢄ Ash Drawer for Large Pedestal
Hꢃꢃꢄꢂ Ash Plug Remover and Rake
Hꢃꢃꢄ9 Complete Baffle/Secondary Burn Tube Assembly
(includes tubes and all mounting hardware)
1ꢃ
1ꢄ
17
18
19
ꢂ9
ꢃ0
H80ꢀ0 Baffle Blanket ꢀꢀ-1/ꢀ” x 1ꢃ-1/ꢀ” x 1”
H80ꢀ1 Baffle Board Kit w/ Baffle Blanket
MISCELLANEOUS PARTS
Hꢃꢃ1ꢄ Aluminum Flex Tubing Kit w/ clamp (1ꢃ” of ꢂ” dia.)
Hꢃꢃꢄꢃ ꢄ” x ꢄ-1/ꢀ” Rodent Screen
----
----
----
710ꢃꢀ
Hꢃꢄꢁꢁ Anti Seize ꢀ gram pouch
711ꢁꢂ Stainless Steel Pipe Reducer from 8” to ꢄ”
Dry Graphite (Apply to door handle and door hinges)
LEGS AND LEG PARTS
18
ꢀ0
Hꢃꢃ1ꢄ Aluminum Flex Tubing Kit w/ clamp (1ꢃ” of ꢂ” dia.)
Hꢃꢃꢃ8 Single Black Cascade Leg
Hꢃꢄꢄ9 Single Black Olympic Leg
Hꢃꢄꢀꢀ Single Gold Olympic Leg
ꢀ1
Hꢃꢄꢀ1 Single Nickel Olympic Leg
Hꢃꢄꢀ0 Single Brushed Gold Olympic Leg
Hꢃꢄ19 Single Brushed Nickel Olympic Leg
Hꢃꢄꢂ9 Heatshield / Leg Fastener Kit
ꢀꢀ
ꢀꢁ
ꢀꢂ
7111ꢄ
Bottom Heatshield / Sꢀꢄ0
Hꢃꢄꢄꢀ Cascade / Olympic Leg Kit Outside Air Plenum Box
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - MODEL Sꢀꢄ0
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - MODEL Sꢀꢄ0
Door Parts
1
2
3
11
8
4
4
5
9
6
7
10
Blower Parts
25
27
28
26
29
31
30
32
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - MODEL Sꢀꢄ0
Leg and Leg Parts
23
20
22
24
18
21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - MODEL Sꢀꢄ0
Ash Drawer Pedestal and Pedestal
18
19
15
17
18
16
19
15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES - MODEL Sꢀꢄ0
PEDESTALS (REqUIRED)
Cat. No.
7111ꢁ
Model
WL-PED
Description
Pedestal (ref. form #506033-16)
Ash Drawer Pedestal (ref. form #506033-15)
7111ꢂ
WL-PED-ASHD
OR LEGS (REqUIRED) (ref. form #506033-14)
70000
70001
7000ꢀ
70007
LEG-OLY-B
LEG-OLY-G
LEG-OLY-N
LEG-OLY-BRG
Olympic Sculptured Blacks (ꢂ per pkg.)
Olympic Sculptured Golds (ꢂ per pkg.)
Olympic Sculptured Nickels (ꢂ per pkg.)
Olympic Sculptured Brushed Golds (ꢂ
per pkg.)
70008
7000ꢁ
LEG-OLY-BRN
Olympic Sculptured Brushed Nickels (ꢂ
per pkg.)
LEG-CAS-B
Cascade Steel Blacks (ꢂ per pkg.)
HEAT SHIELD (REqUIRED WITH LEGS)
WSHS-ꢀꢄ0
7111ꢄ
Heat Shield (ref. form #506033-14)
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)
H790ꢁ
TRAD-FPK-BG-LG
Large Traditional Faceplate Kit,
Brushed Gold
H790ꢄ
TRAD-FPK-G-LG
Large Traditional Faceplate Kit, Gold
BLOWER
H7917
BLWR-FSB700-SS
Blower Kit, FS Woodstoves
OUTSIDE AIR KIT
71111
7111ꢀ
OUTAIRK-L
OUTAIRK-P
Outside Air Kit / Leg (ref. form #506033-18)
Outside Air Kit/Pedestal (ref. form #506033-
17)
MISC.
Paint Gold (1/ꢀ Pint) Paint Gold (1/ꢀ pint)
710ꢃꢁ
710ꢃꢂ
70K99
PaintNickel(1/ꢀPint)
TSPK-B
Paint Nickel (1/ꢀ pint)
Touch-Up Paint , Metallic Black, 1ꢀ oz.
Aerosol
711ꢁꢂ
Hꢃꢁ08
Reducer ꢄ-8”
Pipe Reducer from 8” to ꢄ” Stainless
W-LEGF-LBRKT
Leg Fasetening L - Brackets (ꢂ per pkg.)
(Tie down kit to be used in mobile or
modular homes) (ref. form #506033-18)
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY / LISTING LABEL - ENGLISH
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY / LISTING LABEL - FRENCH
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ. The part number.
ꢂ. The description of the part.
ꢃ. The quantity required.
WARRANTY
Your wood appliance is covered by a limited warranty (provided with the
appliance). Please read the warranty to be familiar with its coverage.
ꢄ. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
Retain this manual. File it with your other documents for future refer-
ence.
LENNOX HEARTH PRODUCTS
1ꢃ08 Elm Hill Pike, Suite 108
Nashville, TN ꢁ7ꢀ10
1-800-9-LENNOX
REPLACEMENT PARTS
See Pages 19 and 20 for a complete replacement parts list. Use only
parts supplied from the manufacturer.
Normally, all parts should be ordered through your Lennox distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
PRODUCT REFERENCE INFORMATION
Werecommendthatyourecordthefollowingimportantinformationabout
your appliance. If you did not purchase your appliance directly from a
Lennox Hearth Products dealer, then please call 1-800-9-LENNOX for the
name and phone number of your nearest Lennox Hearth Products dealer
who will answer your questions or address your concerns.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
ꢀ. The serial number of the appliance.
Your Appliance’s Model Number _______________________________________
Your Appliance’s Serial Number________________________________________
The Date On Which Your Appliance Was Installed __________________________
Your Dealer's Name _________________________________________________
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by Lennox Hearth Products
P/N 77ꢃ,ꢀ1ꢄM Rev. E 0ꢀ/ꢀ010
1ꢃ08 Elm Hill Pike, Suite 108 • Nashville, TN ꢁ7ꢀ10
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
|