A/C power adapter:
Plug enclosed 6-volt a/c power adapter into a wall outlet, then into the weather
station.
Batteries:
308-805 Color Wireless
Atomic Weather Station
Remove battery: Slide tab to the left and pull out to remove battery
cover.
Install three fresh AAA alkaline batteries according to the polarity
markings.
Introduction
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, or Rechargeable Batteries
The Wireless Color Atomic Weather Station offers radio-controlled time, weather
forecast, indoor and outdoor temperature/humidity and heat index with dew point,
on one easy to read display.
If the weather station does not display indoor temperature after 60 seconds,
remove adapter and batteries, and wait for at least 60 seconds before powering up
the weather station again.
Forecast Icons
Time
Alarm Icon
Function
Buttons
INSTALL BATTERIES IN THE TRANSMITTER:
Date display alternates
with Heat Index and
Dew Point display
Remove screws and the battery
cover from the back of the
transmitter with a small screwdriver.
Insert two fresh AAA alkaline
batteries into the transmitter,
observing the correct polarity (see
marking inside battery
TX
Button
Channel
Button
Battery
Compartment
Battery
Cover
compartment).
Keep transmitter 5-10 ft. from the
weather station.
WWVB Reception
FUNCTION BUTTONS
LIGHT/SNOOZE TEMP. SEARCH
IN/OUT
HEAT/DEW MIN/MAX ALARM
SET
Low Battery
Temperature/humidity (indoor or outdoor)
RCC SEARCH
UP
COLOR WEATHER STATION:
C/F
DOWN
FEATURES:
LIGHT ON/OFF
AUTO ROTATE
IN / OUT
• Color animated forecast from changing barometric pressure:
sunny, partly sunny, cloudy, rainy and stormy
• AUTO or MANUAL option toggles IN / OUT data
• IN / OUT temperature (°F / °C) and humidity (%RH)
• MIN / MAX temperature readings.
• ATOMIC time and date (auto sets)
• 12/24-hour time with snooze alarm and alarm icon
• Calendar display: month, day, date
Button
Press and Release Functions
Hold 3-5 seconds
Activates backlight when using
only batteries.
LIGHT/SNOOZE
Trigger snooze when time alarm
is sounding.
• Heat index and dew point
• Light up display with press of button using battery adapter
OR continuous light using AC adapter with ON /OFF option
• Low battery icon for weather station and sensor
• Sits on desktop or tabletop
• Transmits outdoor temperature and humidity
• Over 200 FT. wireless transmission range
Switch between indoor and
outdoor temperature/humidity
readings
TEMP. SEARCH
IN/OUT
Search for remote sensor
Shows Heat Index and Dew
Point
HEAT/DEW
MIN / MAX
ALARM
Shows MIN and MAX values
View Alarm
Resets MIN / MAX values
Alarm set
INITIAL SET UP:
Adapter on the main unit with batteries or a/c adapter and set the time zone &
weather icon:
Enter program menu, set
time, date, forecast icon etc.
SET
Confirm setting.
The Time Zone will flash EST. Press and release the UP or DOWN button to
select the Time Zone. Press and release the SET button.
Search for WWVB signal
RCC SEARCH
UP
Fast advance when setting
Fast backward when setting
The Weather Forecast Icons will flash. Press and release the UP or DOWN
button to select the forecast Icon that represents your current local weather.
Press and release the SET button to confirm.
1 step forward when setting
Select temperature in C/ F
C/F
DOWN
The Temperature area will flash as the display searches for a signal from
the outdoor transmitter.
Insert fresh alkaline batteries into the transmitter, observing the correct
polarity Press the TX button to send a signal after the display is powered up.
Keep the transmitter 5-10 feet from the weather station.
1 step backward when setting
LIGHT ON/OFF
AUTO ROTATE IN / OUT
Turn On or Off Auto-switch
between indoor/outdoor data.
Turn On or Off continuous
backlight on a/c adapter
Within 3 minutes the station will beep and the outdoor temperature should be
displayed on the Weather station. If the outdoor temperature is not displayed
after 3 minutes hold the SEARCH button on the main unit to search for
outdoor sensor. Then press the TX button again on the sensor to send
signal. If that doesn’t work, remove power from both units and start again
from the beginning.
To ensure sufficient 434 MHz transmission, the outdoor transmitter should be
placed a distance of no more than 200 feet (60 meters, open air) from the
Color Weather station.
WWVB RADIO CONTROLLED TIME
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits
the exact time signal continuously throughout the United States at 60 kHz. The
signal can be received up to 2,000 miles away through the internal antenna in the
atomic weather station. However, due to the nature of the Earth’s Ionosphere,
reception is very limited during daylight hours. The atomic weather station will
search for a signal every night when reception is best. The WWVB radio station
derives its signal from the NIST atomic weather station in Boulder, Colorado. A
team of atomic physicists continually measures every second of every day to an
accuracy of ten billionths of a second a day. These physicists have created an
international standard, measuring a second as 9,192,631,770 vibrations of a
Cesium 133 atom in a vacuum. This atomic weather station regulates the WWVB
transmitter.
INSTALL BATTERIES OR A/C POWER ADAPTER INTO THE WEATHER
STATION:
Function Buttons
WWVB RECEPTION icon with full signal strength will appear on screen if the
reception of atomic time is successful. The atomic weather station will have a daily
synchronization at 02:03 and 03:03 everyday. Each reception cycle is minimum
2.5 minutes and maximum 10 minutes.
A/C Adapter
access
Battery
compartment
In normal mode, press the RCC button until the reception icon appears to enforce
searching of radio-controlled clock signal. If this icon disappears afterwards, radio
time signal is not available at the moment.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
covers only actual defects within the product itself, and does not cover the cost of
installation or removal from a fixed installation, normal set-up or adjustments,
claims based on misrepresentation by the seller or performance variations
resulting from installation-related circumstances.
POSITIONING THE OUTDOOR TEMPERATURE SENSOR
The remote temperature sensor should be mounted vertically to avoid damage.
WALL MOUNT
.
Install one mounting screw (not included) into a wall within
transmission
range of the weather station, leaving approximately 3/16 of
an inch (5mm) extended from the wall.
Place the transmitter onto the screw, using the hanging
hole on the backside.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
.
.
Gently pull the transmitter down to lock the screw into
place.
This warranty gives you specific legal rights. You may also have other rights
specific to the State. Some States do not allow the exclusion of consequential or
incidental damages therefore the above exclusion of limitation may not apply to
you.
NOTE: Always ensure that the transmitter locks onto the screw
before releasing.
TABLE STAND
Set the transmitter upright on a table or desk.
For warranty work, technical support, or information contact:
NOTE: This is not recommended as the transmitter may blow over
and be damaged.
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, WI 54601
To achieve a true temperature reading, avoid mounting where direct sunlight can
reach the outdoor temperature sensor. It is recommended to mount the outdoor
temperature sensor on a North-facing wall or in any well shaded area. The
maximum transmitting range in open air is 200-feet (60 meters) obstacles such as
walls, concrete, and large metal objects can reduce the range.
The complete instruction manual is available at:
Le manuel d'instruction complet est disponible sur:
El manual de instrucciones completo está disponible en:
Place both units in their desired location, and wait approximately 10 minutes before
permanently mounting the sensor to ensure that there is proper reception. The
outdoor temperature sensor is not waterproof and should not be placed anywhere
it will become submerged in water or subject to standing water or snow.
SPECIFICATIONS:
Indoor:
Contact Support: 1-608-782-1610
Temperature Range: 32° F to 122° F (0° C to + 50° C)
Humidity Range:
Interval:
20%-99% (RH)
Every 10 seconds
Product Registration:
Outdoor:
Temperature Range: -20°F to 140°F (-29°C to 60°C)
This Device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) the device must accept any interference received, including interference that
may cause undesired operation.
Humidity Range:
Distance:
20%-99% (RH)
200 ft (60 meters) RF 434MHz (open air)
Every 35 seconds
Interval:
Adapter:
Receiver:
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY
TO OPERATE THE EQUIPMENT
6-volt a/c power adapter (included)
Optional 3-AAA, IEC, LR3 alkaline batteries (not included).
2-AAA, IEC, LR3 alkaline batteries (not included).
Transmitter:
Dimensions:
Receiver:
Transmitter:
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
6.29 ” L x 2.6” W x 4.17 ” H (160 x 66 x 106mm)
2.55” L x 1.18” W x 3.5” H (65 x 30 x 90mm)
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We accept
no liability for technical mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
Printed in China
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original purchaser
of this product. To receive warranty service, the purchaser must contact La
Crosse Technology, Ltd for problem determination and service procedures.
Warranty service can only be performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to La Crosse Technology, Ltd or La Crosse
Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at
no charge as stipulated herein, with new or reconditioned parts or products if found
to be defective during the limited warranty period specified above. All replaced
parts and products become the property of La Crosse Technology, Ltd and must
be returned to La Crosse Technology, Ltd. Replacement parts and products
assume the remaining original warranty, or ninety (90) days, whichever is longer.
La Crosse Technology, Ltd will pay all expenses for labor and materials for all
repairs covered by this warranty. If necessary repairs are not covered by this
warranty, or if a product is examined which is not in need or repair, you will be
charged for the repairs or examination. The owner must pay any shipping charges
incurred in getting the La Crosse Technology, Ltd product to a La Crosse
Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay
ground return shipping charges to the owner of the product to a USA address only.
The La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must be
presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions
contained in the owner’s manual; (5) damage resulting from the performance of
repairs or alterations by someone other than an authorized La Crosse Technology,
Ltd authorized service center; (6) units used for other than home use (7)
applications and uses that this product was not intended or (8) the products
inability to receive a signal due to any source of interference.. This warranty
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|