OWNER’S MANUAL 2007
990 SUPER DUKE
990 SUPER DUKE R
ART. NR. 3.211.151 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION »
2
INTENDED PURPOSE
The 990 Super Duke is designed to resist the usual wear and tear of paved roads but is not designed for race courses or off-road use.
The 990 Super Duke R is designed to resist the usual wear and tear of paved roads or race courses but is not designed for off-road use.
OWNER'S MANUAL
Carefully read the entire Owner's Manual before you start riding your motorcycle, even if this will take a little time. It contains use-
ful tips and information on the best way to handle the motorcycle and how to protect yourself from injuries. The Manual also con-
tains important information on service and maintenance. In your own interest, pay particular attention to the information marked
as follows:
– Ignoring these instructions, can endanger your body and
your life.
– Ignoring these instructions could cause damage to parts
of your motorcycle or that the motor-cycle is not road-safe
anymore.
The Owner's Manual corresponded to the latest information available for this model series at the time it was printed. Minor devia-
tions resulting from enhancements to the motorcycle design cannot be entirely precluded. The Owner's Manual is an integral part
of the motorcycle and must be handed over to the new owner when the motorcycle is sold.
SERVICE
Observance of the service, maintenance and operating instructions for the engine and chassis specified in the Owner's Manual is
a prerequisite for faultless operation and the avoidance of premature wear. Please observe the prescribed breaking-in periods, inspec-
tion intervals and service intervals. Strict observance will significantly prolong the service life of your motorcycle.
The use of the motorcycle under extreme conditions, e.g. on the race course, can cause above average wear to components such
as the brakes. In this case it may become necessary to service or replace wear parts before the service limit specified in the main-
tenance schedule has been reached.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION »
3
WARRANTY
The service work specified in the „Lubrication and Maintenance Schedule“ must be performed by an authorized KTM workshop.
This is the only place that has the qualified technicians and the special tools required for the 990 Super Duke / R. Be sure to have
the workshop verify all service work carried out in the service manual to avoid losing your right to claim under the warranty.
The warranty or guarantee shall become void for damage and consequential damage caused by manipulations or conversions to the
motorcycle.
AUTOMOTIVE FLUIDS
The fuels, lubricants and liquids specified in the Owner's Manual or automotive fluids with equivalent specifications must be used
in accordance with the maintenance schedule.
SPARE PARTS, ACCESSORIES
For your own safety, only use spare parts and accessories approved by KTM. KTM shall not assume any liability for other products
or consequential damage resulting from the use of such products.
ENVIRONMENT
Motorcycle driving is a wonderful sport and we hope that you will be able to enjoy it to the full. It may, however, involve potential
problems for the environment or lead to conflicts with others. These problems or conflicts can be avoided if the motorcycle is used
responsibly. To safeguard the future of motorcycle sports, make sure that you use the motorcycle in accordance with the law, show
that you are environmentally conscious and respect the rights of others.
Enjoy driving your motorcycle !
KTM SPORTMOTORCYCLE AG
5230 MATTIGHOFEN, AUSTRIA
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX »
4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . .2
SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . .6
Chassis number, Type label . . . . . . . . . . . . . . . . . . . . . . . . .6
Engine number, engine type . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION INSTRUMENTS . . . . . . . . . . . . . . . . . . . . . . . . .7
Clutch lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Hand brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Combined instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Function buttons on combined instrument . . . . . . . . . . . . .8
Combined instrument display . . . . . . . . . . . . . . . . . . . . . .8
Cooling liquid temperature display . . . . . . . . . . . . . . . . . .12
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Combination switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Starter tip switch, Emergency OFF tip switch . . . . . . . . . .15
Filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Seat lock, removing the seat . . . . . . . . . . . . . . . . . . . . . .16
Baggage loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Tool set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Helmet lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Holding strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Shift lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Side stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Foot brake pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Footrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Compression damping of fork . . . . . . . . . . . . . . . . . . . . . .19
Rebound damping of fork . . . . . . . . . . . . . . . . . . . . . . . . .19
Spring preload of the fork . . . . . . . . . . . . . . . . . . . . . . . . .20
Damping action during compression of shock absorber . . . .20
Rebound damping of shock absorber . . . . . . . . . . . . . . . . .21
GENERAL TIPS AND WARNINGS FOR STARTING
THE MOTORCYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Instructions for initial operation . . . . . . . . . . . . . . . . . . . .22
Running in the LC8 engine . . . . . . . . . . . . . . . . . . . . . . . .22
Accessories and payload . . . . . . . . . . . . . . . . . . . . . . . . . .23
DRIVING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .24
Check the following before each start . . . . . . . . . . . . . . . .24
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Starting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Shifting/Riding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Stopping and parking . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
PERIODIC MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . .32
MAINTENANCE WORK ON CHASSIS AND ENGINE . . . . . . . .36
Adjusting the fork and shock absorber . . . . . . . . . . . . . . .37
Adjusting compression damping of fork . . . . . . . . . . . . . . .37
Adjusting rebound damping of fork . . . . . . . . . . . . . . . . . .37
Adjusting the spring preload on the fork . . . . . . . . . . . . . . .38
Compression damping of shock absorber . . . . . . . . . . . . . .38
Rebound damping of shock absorber . . . . . . . . . . . . . . . . .39
Checking the chain tension . . . . . . . . . . . . . . . . . . . . . . .40
Correcting the chain tension . . . . . . . . . . . . . . . . . . . . . .40
Chain maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Checking the chain for wear . . . . . . . . . . . . . . . . . . . . . . .41
General information on KTM disk brakes . . . . . . . . . . . . . .42
Adjusting the basic position of the hand brake lever . . . . . .44
Checking the front brake fluid level . . . . . . . . . . . . . . . . .44
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX »
5
Checking the front brake pads . . . . . . . . . . . . . . . . . . . . .45
Checking the rear brake fluid level . . . . . . . . . . . . . . . . . .46
Checking the rear brake pads . . . . . . . . . . . . . . . . . . . . . .46
Dismounting and remounting the front wheel . . . . . . . . . .48
Dismounting and mounting the rear wheel . . . . . . . . . . . . .50
Tires, air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Removing and remounting the battery . . . . . . . . . . . . . . .53
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Jump start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Fuses for individual power consumers . . . . . . . . . . . . . . . .56
Replacing the headlight lamp . . . . . . . . . . . . . . . . . . . . .57
Adjusting the headlight range . . . . . . . . . . . . . . . . . . . . . .58
Replacing the brake light and taillight bulbs . . . . . . . . . . .59
Replacing the flasher bulbs . . . . . . . . . . . . . . . . . . . . . . .59
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Checking the cooling liquid level in the compensating tank . .61
Checking the cooling liquid level in the radiator . . . . . . . . .62
Bleeding the cooling system . . . . . . . . . . . . . . . . . . . . . .62
Changing the basic position of the clutch lever . . . . . . . . .64
Checking the oil level of the hydraulic clutch . . . . . . . . . . .64
Adjusting the handlebar tilt . . . . . . . . . . . . . . . . . . . . . . .64
How to change the handlebar position (Super Duke R) . . . .65
Adjusting the steering damper (Super Duke R) . . . . . . . . .65
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Checking the engine oil level . . . . . . . . . . . . . . . . . . . . . .66
Refilling engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Changing the engine oil and the oil filter,
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
CONSERVATION FOR WINTER OPERATION . . . . . . . . . . . . . .77
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
STARTING UP AFTER IMMOBILIZATION . . . . . . . . . . . . . . .78
TECHNICAL SPECIFICATIONS – CHASSIS . . . . . . . . . . . . . . .79
TECHNICAL SPECIFICATIONS – ENGINE . . . . . . . . . . . . . . .83
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
HEAD WORD INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
CONSUMER INFORMATION FOR USA ONLY . . . . . . . . . . . . .87
cleaning the oil screen . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL NUMBER LOCATIONS »
6
Chassis number, Type label
The chassis number is stamped on the right side of the steering head tube. Enter this num-
ber in the field on page no 1.
The type label is located on the right frame tube under the seat.
Engine number, engine type
The engine number and the engine type are stamped into the left side of the engine below
the engine sprocket. Enter this number on page 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
7
Clutch lever
The clutch lever [1] is fitted on the left hand side of the handle bar. The adjusting screw [A]
is used to change the original position of the clutch lever (see maintenance work on chas-
sis and engine).
A
The clutch is hydraulically actuated and adjusts itself automatically.
1
Hand brake lever
The hand brake lever [2] is mounted on the handlebar on the right and actuates the front
wheel brake.The adjusting screw [B] is used to change the original position of the hand brake
lever (see maintenance work on chassis and engine).
B
2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
8
Combined instrument
The combined instrument is divided into 4 parts.
Function buttons: to select the display modes and basic settings in the display
Tachometer:
displays the engine speed
Indicator lamps: provide additional information on the motorcycle operating condition
Display:
shows the speed, cooling liquid temperature, time, ambient temperature,
distance traveled (ODO), trip master 1 (TRIP 1), trip master 2 (TRIP 2),
distance traveled since the reserve warning lamp went on (TRIP F)
Function buttons on combined instrument
MODE [1]
Briefly press the MODE button to go to the next display mode. The available display modes
are ambient temperature, distance traveled (ODO), trip master 1 (TRIP 1) and trip master
2 (TRIP 2).
1
2
The speed, cooling liquid temperature and time are always displayed.
SET [2]
Press the SET button to reset trip master 1 or 2 to 0.
The 3rd button is not programmed.
Combined instrument display
TEST
When you switch on the ignition, all of the display elements will light up for 1 second for
the function test.
LENGTH
The display will change for 1 second to display the circumference of the front wheel in mil-
limeters. 1870 mm corresponds to a 17" front wheel.
Then the display will change back to the mode that was activated when the ignition was
switched off.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
9
SPEED [1]
The speed can be displayed in kilometers per hour (km/h) or miles per hour (mph).
CHANGING THE SPEED DISPLAY FROM KM/H - MPH or MPH - KM/H
Switch on the ignition and press the MODE button more than 10 seconds in the ODO mode.
1
CLOCK [2]
The dots between the hours and minutes will blink in the CLOCK display.
The clock must be set if the battery was disconnected or if the fuse 6 was blown.
SETTING THE CLOCK
Switch on the ignition and select the ODO mode. Press and hold the MODE button while
you press the SET button more than 1 second. The time will start to blink.
Use the MODE button to set the hours. Use the SET button to set the minutes.
Then press the MODE and SET buttons simultaneously.
2
AMBIENT TEMPERATURE [3]
The ambient temperature can be displayed in Celsius (°C) or Fahrenheit (°F).
CHANGING THE AMBIENT TEMPERATURE DISPLAY FROM °C - °F or °F - °C
Switch on the ignition and press the MODE button more than 10 seconds in the ambient
temperature mode.
Press the MODE button to go to the next display mode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
10
FROST WARNING [1]
The frost symbol will start to blink regardless of the mode if the ambient temperature drops
below 3°C (37.5°F).
1
ODO [2]
Displays the total kilometers or miles traveled.
This figure will not be cleared if the battery is disconnected.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
11
TRIP 1 [1]
The trip meter 1 is always active and counts up to 999.9. It is used to measure the length
of the trip or the distance between 2 refueling stops.
TO RESET TRIP 1
To reset the trip meter 1 to zero, switch on the ignition, select the TRIP 1 display mode and
press the SET button more than 2 seconds.
1
Press the MODE button to go to the next display mode.
TRIP 2 [2]
The trip meter 2 is always active and counts up to 999.9. It is used just like TRIP 1.
TO RESET TRIP 2
To reset the trip meter 2 to zero, switch on the ignition, select the TRIP 2 display mode and
press the SET button more than 2 seconds.
Press the MODE button to go to the next display mode.
2
TRIP F [3]
When the fuel level reaches the reserve mark, the display will automatically switch to TRIP
F and begin to count (no matter which display mode was active before). At the same time,
the fuel warning lamp will light up. You will still have enough reserve fuel for at least 30
kilometers.
After refueling, it will take approx. 3 minutes for the fuel lamp to go out, TRIP F to auto-
matically reset to 0 and to return to the previous display mode.
3
NOTE:
Press the SET button for 2 seconds to switch off the fuel warning lamp.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
12
Cooling liquid temperature display
The temperature display [1] is shown in 12 bars. The more bars that light up, the hotter the
cooling liquid. When the upper bar lights up 120°C (248°F), all of the bars will start to blink
and the red warning lamp [2] will light up.
heiß/hot/caldo/chaud/caliente
normal
normally
normalemente
normalment
normalmente
1
Possible causes for an increase in temperature, causing the red warning light for the cool-
ing liquid temperature to light up:
– Driving too slowly and driving with a heavy load at high air temperatures
– Not enough cooling liquid in the system
– The ventilator on the left radiator is not running
– Improper use of the clutch when driving slowly
kalt / cold / freddo / froid / frío
2
Tachometer
3
The tachometer [3] shows the engine speed in revolutions per minute. Do not run the engine
beyond the orange mark at 9500 rpm.
The speed limiter will set in at 9600 rpm, drastically reducing the engine power above this
rotational speed.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
13
Indicator lamps
The green indicator lamp will blink in the blinker rhythm when the blinker is
switched on.
NOTE: The indicator lamp will blink slower when a blinker is broken.
The green indicator lamp will light up when the gearbox is in an idling position.
The blue indicator lamp will light up when the high beams are switched on.
The red warning light will light up when the cooling liquid has reached a tempera-
ture of approx. 120°C (248°F).
The orange warning lamp will light up when the fuel level has reached the reserve mark.
At the same time the display will automatically change to TRIP F (see TRIP F).
The red warning lamp lights up when the ignition is switched on but the engine is
not running. When the engine is started, the warning lamp will go out as soon as the
oil pressure is high enough.
The orange warning lamp (fuel injection) briefly lights up when the ignition is switched
on. It will go out when the gasoline pressure is high enough.
If this warning lamp lights up while driving, a component in the injection system is
defective. The error can be identified by means of a blink code (see Trouble shoot-
ing).
The red warning lamp will light up if the voltage in the on-board electrics drops below
10 volts. Immediately drive to the nearest authorized KTM workshop and have the
electrical system checked.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
14
Ignition lock
The ignition lock has 3 switching positions.
Ignition off, (engine can't be started)
Ignition on, (engine can be started)
Ignition off, handlebar blocked
To switch the ignition to position
turn the ignition key to position
and firmly press it
into the lock. Turn the handlebar to the left, then turn the ignition key to the left.
The ignition key can be withdrawn in position
and
.
2
Combination switch
The rocker switch LIGHTS [1] actuates the high beam or low beam.
High-beam light
Low-beam light
The light signal (high beam) is actuated with button [2].
1
The indicator switch [3] returns to central position after actuation. Press flasher
switch towards switch housing to switch off the flasher.
1
The horn is sounded with button [4].
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
15
Starter tip switch, Emergency OFF tip switch
The emergency off switch [1] is provided for emergency situations and should not be used
to switch off the engine.
1
The engine is ready for operation in position
(ignition circuit and starter circuit are switched
(ignition circuit and starter circuit are inter-
on).
The engine cannot be started in position
rupted).
3
Use the starter tip switch [3] to operate the electric starter.
Filler cap
The filler cap [4] can be locked. It is equipped with a tank ventilation system.
To open, insert the ignition key, turn 45° in a clockwise direction and tilt the filler cap back.
After refueling, pull out the ignition key and press down on the filler cap until the lock engages.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
16
Seat lock, removing the seat
1
The seat lock [1] can be locked with the ignition key.
To remove the seat, insert the ignition key and turn 90° in a clockwise direction. Lift the
seat in the back while pressing near the holding strap and pull off towards the back.
To mount the seat, place it on the motorcycle and position the hooks [2] on the bottom of
the seat behind the dollies [3] on the subframe. Press down on the seat near the holding
strap while sliding it forwards. The two tabs [4] must hook onto the tank. Turn the ignition
key in the seat lock 90° in a counterclockwise direction and pull off. Check whether the seat
is mounted correctly.
2
4
3
Baggage loops
5
4 loops [5] are mounted on the bottom of the seat to which small pieces of baggage can be
fastened. Fold the loops towards the outside to make them accessible when the seat is mounted.
Baggage weight: max. 5 kg
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
17
Tool set
The tool set [1] is located in the storage compartment under the seat.
1
Helmet lock
The steel rope [2] in the tool bag can be used to secure a helmet.
3
To secure, remove the seat, run the rope through the helmet, attach both ends to the hook
[3] and mount the seat.
The helmet lock is provided to secure the helmet to the motorcycle when parked. Do not
attach the helmet or other objects to the steel rope while driving. You can easily lose con-
trol of the motorcycle.
2
Holding strap
The passenger should hold on to the holding strap [4] or the driver while riding.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
18
Shift lever
The shift lever is mounted on the left side of the engine. The position of the gears is shown
in the illustration. Neutral, or the idle speed, is located between first and second gear.
The basic position of the shift lever can be adjusted according to your seating position (see
Maintenance work).
2,3,4,5,6
N
1
Side stand
Fold the side stand [1] forward to the stop with your foot and put the weight of the motor-
cycle on the stand. Make sure it is standing securely on a firm surface. The side stand is
linked to the safety start system; follow the driving instructions.
1
Foot brake pedal
The foot brake pedal [2] is located in front of the right footrest. Its basic position can be
adjusted to your seat position.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
19
Footrests
The passenger footrests [1] fold up.
1
Compression damping of fork
The fork's damping action during compression travel (compression damping) can be adjusted.
This allows you adjust the damping behavior to match your driving style and the payload.
The adjusting screws [2] are located on the fork leg axle passage.
2
More information is provided in the chapter „Adjusting the fork and shock absorber“.
Rebound damping of fork
The fork's damping action during rebound travel (rebound damping) can also be adjusted.
This allows you adjust the damping behavior to match your driving style and the payload.
The adjusting screws [3] are located on the upper end of the fork legs.
3
More information is provided in the chapter "Adjusting the fork and shock absorber.“
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
20
Spring preload of the fork
The fork's preload can be adjusted by means of the adjusting screws [1].
More information is provided in the chapter „Adjusting the fork and shock absorber“.
1
Damping action during compression of shock absorber
The shock absorber's damping action during compression travel (compression damping) can
be adjusted. This allows you adjust the shock absorber's damping behavior to match your
driving style and the payload.
The damping rate can be adjusted in the low and high-speed range (Dual Compression Control).
The designation low and high-speed refers to the movement of the shock absorber and not
to the motorcycle's driving speed.
3
2
The adjusting screw [2] for the low-speed range can be adjusted with a screwdriver.
The adjusting screw [3] for the high-speed range can be adjusted with a 17 mm socket wrench.
More information is provided in the chapter „Adjusting the fork and shock absorber“.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUMENTS »
21
Rebound damping of shock absorber
The shock absorber's damping action during rebound travel (rebound damping) can also be
adjusted. This allows you adjust the damping behavior to match your driving style and the
payload.
The adjusting screw [1] is located on the bottom of the shock absorber.
More information is provided in the chapter "Adjusting the fork and shock absorber.“
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL TIPS AND WARNINGS FOR STARTING THE MOTORCYCLE »
km (620 miles). The maximum number of
22
Instructions for initial operation
– Remove your foot from the foot brake
lever when you are not braking. If the foot
brake lever is not released the brake pads
rub continuously and the braking system
is overheated.
– Do not make any alterations to the motor-
cycle and always use ORIGINAL KTM
SPARE PARTS. Spare parts from other
manufacturers can impair the safety of
the motorcycle.
revolutions per minute must not go exceed
6500 rpm. Once you have run your engine
in for 1000 km, you may push it to its 9500
rpm limit , i.e. up to the orange zone indi-
cated in the tachometer. Exceeding the above
listed rotations as well as pushing high rpm
when the engine is cold will have an adverse
effect on the life of your engine.
– Make sure the work for the „pre-delivery
inspection“ was performed by your author-
ized KTM workshop. The DELIVERY CER-
TIFICATE and SERVICE MANUAL will
be handed over when you pick up your
vehicle.
– Read these operating instructions care-
fully before your first ride.
– Enter the chassis, engine and key num-
bers on page 1.
– Familiarize yourself with the operating
elements.
– Adjust the clutch lever, the hand brake
lever, the foot brake lever and the shift
lever in the position that is most conven-
ient for you.
– This motorcycle is equipped with a three-
way catalytic converter. Leaded fuel will
destroy the converter. Always use unleaded
fuel.
– Get used to handling the motorcycle on
an empty parking lot, before starting on
a longer drive. Also try to drive as slowly
as possible and in standing position, to
improve your feeling for the vehicle.
– You may only be accompanied by a pas-
senger if your motorcycle is fitted and reg-
istered for such purposes. The passenger
must hold on to the supporting strap or
the driver and keep his feet on the pas-
senger footrests throughout the ride.
– New tires have a smooth surface, which
means that they must be run in to achieve
full grip. For this purpose, ride the motor-
cycle carefully at moderate speed during
the first 200 kilometers with new tires,
tilting the vehicle at different angles so
that all sections are properly roughened.
Tires will not display their full grip char-
acteristics until they are properly run in.
– Motorcycles are sensitive to changes in
the weight distribution. Read the section
on „Accessories and payload“ when car-
rying luggage.
– Wear suitable clothing when driving a
motorcycle. Clever KTM drivers always
wear a helmet, boots, gloves and a jacket,
regardless of whether driving all day or
just for a short trip. The protective cloth-
ing should be brightly colored so that
other vehicle can see you as early as
possible. Your passenger will also need
suitable protective clothing.
– Do not drive after having consumed
alcohol.
– Always turn on the light to make sure
that other drivers become aware of you
as early as possible.
– Drive at a moderate speed for the first few
kilometers of each trip to allow the tires
to reach the necessary operating temper-
ature. Maximum road grip is assured when
the tires are warm.
– The front and rear wheel are allowed to
be fitted only with tires that have the
same profile type.
– Pay attention to running-in procedure.
Running in the LC8 engine
Even finely machined surfaces of engine
parts have rougher surfaces than parts that
slide on each other for a long time. Therefore,
every engine must be run in. For this reason,
do not demand maximum performance from
the engine for the first 1000 kilometers (620
miles). The vehicle must be run in at low,
changing performance level for the first 1000
–
Hold the handlebars with both hands
and leave your feet on the foot rests while
driving.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL TIPS AND WARNINGS FOR STARTING THE MOTORCYCLE »
23
– You may only be accompanied by a pas-
senger if your motorcycle is fitted and reg-
istered for such purposes.
impair driving safety.
– A high payload will change the motorcy-
cle's handling and considerably increase
the braking distance; adapt your driving
speed accordingly.
– The tires must be designed for a speed
of over 240 KPH (speed symbol ZR) and
must be released by KTM.
– Never leave your motorcycle without super-
vision if the engine is running.
– New tires have a smooth surface, which
means that they must be run in to achieve
full grip. For this purpose, ride the motor-
cycle carefully at moderate speed during
the first 200 kilometers with new tires,
tilting the vehicle at different angles so
that all sections are properly roughened.
Tires will not display their full grip char-
acteristics until they are properly run in.
– Wheels with a different rim diameter or
other rim width may not be mounted oth-
erwise the vehicle handling will no longer
be safe.
– Never exceed the maximum permissible
laden weight and the axle weights. The
maximum permissible laden weight is
made up of the following components:
– Motorcycle ready for operation and tank
full
Accessories and payload
Accessory parts and baggage can signifi-
cantly decrease a motorcycle's driving stabil-
ity. Please observe the following warnings.
– Luggage
– Driver and passenger with protective
clothing and helmet
– Never drive faster than 130 kph (80 mph)
if you have mounted accessory parts on
your motorcycle. Accessory parts can sig-
nificantly impair the motorcycle's han-
dling, especially in the maximum speed
range.
– Observe the traffic regulations, drive
defensively and trying to look ahead as
far as possible so that any hazards can
be recognized as early as possible.
– The faster you drive, the more sensitive
your motorcycle will be to crosswind and
changing road conditions. Your motorcy-
cle can easily go out of control at high
speeds.
– Choose your driving speed according to
the conditions and your driving skills.
– Drive carefully on unknown roads or on
unfamiliar trials.
– Never drive faster than 130 kph (80 mph)
if your motorcycle is loaded with cases
or other baggage. They will impair the
motorcycle's handling at higher speeds and
can easily cause it to go out of control
– If you have cases mounted, do not exceed
the manufacturer's recommended maxi-
mum payload.
– Four loops are provided on the bottom of
the seat to attach your luggage. Make
sure your luggage does not extend beyond
the silencer, otherwise it may become
singed from the heat.
– Renew the vizor on your helmet on time
so as to ensure optimum vision in any sit-
uation. When light shines directly on
scratched visor, the operator will be
blinded.
– Make sure your luggage does not cover
the tail light.
– Baggage must be securely and adequately
fastenend; loose baggage will significantly
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
24
Check the following before each start
When you start, the motorcycle must be in perfect mechanical condition. For safety reasons,
you should make a habit of performing an overall check of your motorcycle before each start.
The following checks should be performed:
1
FUEL
Check the fuel quantity in the tanks.
2
CHAIN
Check the tension and condition of the chain.
A loose chain can fall off the sprockets and a worn-out chain can tear. In both cases this
can damage other motorcycle components and cause the motorcycle to go out of con-
trol. A chain that is too tight or not greased will cause unnecessary wear to the chain
and sprockets.
3
4
TIRES
Check for damaged tires. Tires showing cuts or dents must be replaced. The tread depth
must comply with the legal regulations. Also check the air pressure. Insufficient tread
and incorrect air pressure deteriorate the driving performance.
BRAKES
Check correct functioning of the braking system. Check for sufficient brake fluid in the
reservoir. The reservoirs have been designed in such a way that brake fluid does not need
to be refilled even when the brake pads are worn. If the level of brake fluid falls below
the minimum value, this indicates a leak in the braking system or completely worn out
brake pads. Arrange for the braking system to be checked by a KTM specialist, as com-
plete failure of the braking system can be avoided.
Also check the state of the brake hose and the thickness of the brake linings.
Check free travel at hand brake lever and foot brake lever.
5
CABLES
Check the throttle cable for correct adjustment and smooth operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
25
6
COOLING FLUID
Check the level of cooling fluid when the engine is cold.
7
ELECTRICAL SYSTEM
Start the engine and check the headlight, tail lamp, brake light, turn signals, indicator
lamps, horn and emergency-off switch for proper functioning.
8
9
CHECK OIL LEVEL
Insufficient oil results in premature wear and consequently to engine damage.
BAGGAGE, PAYLOAD
Never exceed the maximum total weight (387 kg, 853 lbs) and the motorcycle's wheel
loads. The maximum total weight is comprised of:
– the motorcycle in a running condition and refueled (199 kg, 439 lbs)
– the baggage and accessories
– the driver and passenger with protective gear and helmet
Adjust the tire inflation pressure as well as the preload and damping properties of the
fork and shock absorber to the total weight.
Make sure your luggage is correctly fastened before you drive off.
10 REAR MIRROR
Sit on the motorcycle and check the adjustment of the rear mirror.
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
26
Starting the engine
1
2
Switch on emergency OFF switch [1].
Switch on ignition (turn ignition key [2] into position ).
NOTE:
1
You will hear the operation of the fuel pump for approx. 2 seconds after switching on
the ignition. The FI indicator lamp will also light up during this time and the engine can-
not be started.
Switch transmission to idle (green indicator lamp N [3] lights up).
Do not accelerate; operate starter button [5].
NOTE:
3
4
If you accelerate during the starting process you will hear a loud, metallic
sound caused by the torque limiter. The torque limiter protects the
components in the starter drive from being damaged.
The oil pressure warning lamp [4] should go out as soon as the engine is running.
Take the load off the side stand and fold the side stand all the way up.
3
4
5
6
– Do not start the engine and allow it to idle in a closed room. Exhaust fumes are poison-
ous and can cause loss of consciousness and death. Always provide adequate ventila-
tion while the engine is running.
– Never operate the motorcycle with a run-down battery or without the battery. This can
damage the electronic components or safety equipment in either caseand the motorcy-
cle will no longer be roadworthy.
2
– If you accelerate while starting, the engine management will not inject any fuel and the
engine will not start. Do not accelerate while starting!
– If the oil pressure warning lamp does not go out as soon as the engine is running, imme-
diately switch off the engine. If the engine is not switched off, engine damage will occur
within a short period of time. Check the engine oil level or contact a ktm workshop.
– Maximum period for continuous starting: 5 seconds. Wait at least 5 seconds before try-
ing again.
– Don’t ride your motorcycle with full load and don’t rev engine when cold. Because the
piston is warming up faster than the water cooled cylinder, it can cause engine damage.
Always let the engine warm up before and refrain from driving with full load until the
engine is warm.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
27
IF THE ENGINE IS DOES NOT CRANK WHEN
YOU ACTUATE THE STARTER TIP SWITCH:
– whether you accelerated while starting
– the transmission is switched to idle
– Check if the emergency OFF switch is on
– Check if the ignition is on
pulled. The engine will stall if a gear is
Let clutch lever go slowely and open throt-
tle or shift down again.
engaged and the clutch lever is released with
the side stand folded down.
If the engine is killed f.ex. at a crossing, sim-
ply pull the clutch lever and start. It is not
necessary to switch the gear to NEUTRAL.
Stop immediately if the FI indicator lamp lights
up while driving. The FI indicator lamp will
start blinking as soon as the transmission is
in neutral. The rhythm of the blinking lamp
will let you determine the two-digit „blink
code“, e.g.:
Blink code 34: FI blinks 3x long, 4x short,
pause,
Blink code 06: FI blinks 6x short, pause
The blink code will indicate which compo-
nent is defective (see Troubleshooting). This
makes it possible to pinpoint the defect if a
diagnostic tool is unavailable.
Starting off
Pull the clutch lever and engage 1st gear.
Slowly release the clutch lever while you gen-
tly accelerate.
– the headlight is on
– If this is not the case, the battery is dis-
charged
– If the lights are on, proceed as described
in the „Trouble-shooting“ section or
contact a KTM dealer.
Do not attach a helmet or other objects to
the helmet lock rope while driving. You can
easily lose control of the motorcycle.
IF THE ENGINE CRANKS BUT DOES NOT
START, WHEN YOU ACTUATE THE STARTER
TIP SWITCH:
– whether you accelerated while starting
– whether the FI indicator lamp is blinking
– if yes, check Troubleshooting - Blink
codes table
– Check if sufficient fuel is in the tank
– If this is not the case, refill the tank
– if sufficient fuel is in the tank, pro-
ceed as described in the „Trouble-
shooting“ section or contact a KTM
dealer.
Shifting/Riding
You are now in first gear, refered to as the
drive or uphill gear. Depending on the con-
ditions (traffic, road gradient, etc.), you can
shift to a higher gear. Close throttle, at the
same time pull clutch lever and shift to the
next higher gear. Let clutch lever go again
and carefully open throttle. Do not shift gears
and accelerate carefully in curves.
– Avoid abrupt load changes while riding
around bends and on wet or slippery
ground. Otherwise you might easily lose
control over your motorcycle.
Only accelerate to the extent that road and
weather conditions allow. Be especially care-
ful when you accelerate in curves. Abrupt
opening of the throttle can cause the motor-
cycle to go out of control and also increases
fuel consumption.
By shifting down, use the brakes if neces-
sary and close throttle at the same time. Pull
clutch lever and shift down to the next gear.
NOTE:
This motorcycle is equipped with a safety start-
ing system. The engine can only be started
if the transmission is in neutral or the clutch
lever is pulled. If the side stand is folded down,
the engine can only be started if the trans-
mission is in neutral or the clutch lever is
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
28
bar on the temperature indicator lights up.
– If the red oil pressure warning lamp lights
up while driving, the oil pressure is too
low to adequately lubricate the engine.
Stop immediately and switch off the
engine. if you continue to drive, engine
damage will occur within a short period
of time. Check the engine oil level or con-
tact an authorized KTM workshop.
–
improper use of the clutch while driving
at low velocities
– While riding your motorcycle, never switch
Let the engine cool down. Meanwhile,
check whether any cooling liquid is leak-
ing out of the motorcycle. Check the cool-
ing liquid level in the radiator (not only
in the compensating tank). - CAUTION
SCALDING HAZARD! Do not drive on,
until there is sufficient liquid in the col-
ing system.
– In the event that, while riding on your
motorcycle, you notice any unusual oper-
ation-related noise, stop immediately,
turn the engine off, and contact an author-
ized KTM dealer.
the ignition lock to positions
and
.
– Do not try to change the settingsof the
combined instrument while driving. Your
attention will be distracted from the traf-
fic and this may cause you to lose con-
trol of your motorcycle.
– The frost symbol * in the combined instru-
ment will start to blink on icy roads. Adapt
your speed to the road and weather con-
ditions.
– The passenger must hold on to the driver
or the holding strap on the seat while rid-
ing and keep his/her feet on the passen-
ger footrests.
– Regularly make sure that the baggage
and cases are tightly fastened.
– After falling with the motorcycle, check
all functions thoroughly before starting up
operations again.
– A bent handlebar must always be replaced.
Never try to straighten the handlebar
because this will cause it to lose its sta-
bility.
– Never have the throttle wide open when
changing down to a lower gear. The engine
will overspeed, damaging the valves. In
addition, the rear wheel blocks so that the
motorcycle can easily get out of control.
– Never use your motorcycle without an air
filter. Otherwise dust and dirt may enter
the engine and cause increased wear.
– Stop immediately if a perceptible power
loss occurs while driving due to a defec-
tive ignition caused by a cylinder misfir-
ing or breaking down. If the unburned
fuel/air mixture reaches the catalytic con-
verter, it will ignite and the resulting heat
will destroy the catalytic converter and the
adjoining components.
Braking
Close throttle and apply the hand and foot
brakes at the same time. Carefully apply the
brakes on sandy, wet or slippery surfaces.
Always brake with feeling, blocking wheels
can cause you to skid or fall. Also change down
to lower gears depending on your speed.
Always finish braking before you enter a
curve.
When driving downhill, use the braking effect
of the engine. Change down one or two gears
but do not overspeed the engine. In this way,
you will not need to brake so much and the
brakes will not overheat.
– The red coolant warning lamp lights up
when the coolant temperature has reached
120°c (248°F).
– High rpm rates when the engine is cold
have an adverse effect on the life of your
engine. We recommend you run the engine
in a moderate rpm range for a few miles
giving it a chance to warm up. After that
no further precautions in this respect
need be taken. The engine has reached
operating temperature as soon as the 4th
Possible causes for the increase in tem-
perature:
– low driving velocity and high load sit-
uation in high air temperatures
– level of coolant in the system is insuf-
ficient
– In the rain, or after the motorcycle has
been washed, braking action may be
delayed due to wet brake discs. First, the
brakes must be braked dry.
– fan at radiator is not running
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
29
– When you brake, the brake discs, brake
pads, brake caliper and brake fluid heat
up. The hotter these parts get, the weaker
the braking effect. In extreme cases, the
entire braking system can fail.
something is wrong with the brake sys-
tem. Don’t ride your motorcycle anymore
without first having the brake system
looked over by a KTM dealer.
– On salt-sprayed or dirty roads brake action
may be delayed as well. First, the brakes
must be braked clean.
– Remember that the stopping distance
will be longer if you are carrying a pas-
senger or baggage.
– If the resistance in the hand brake lever
or foot brake pedal feels „spongy“ (too
much play), this is an indication that
Stopping and parking
Apply the brakes fully and put the engine into neutral. To stop the engine, switch off the
ignition. Fold the side stand forward to the stop with your foot, put the weight of the motor-
cycle on the stand and park the bike on a firm surface. Lock the motorcycle.
– always park your motorbike on a solid and horizontal surface.
–
Never leave your motorcycle without supervision as long as the engine is running.
– Motorcycle engines produce a great amount of heat while running. The engine radiators,
exhaust, exhaust system, brake discs, and shock absorbers can become very hot. Do not
touch any of these parts after operating the motorcycle, and take care to park it where
pedestrians are not likely to touch it and get burned
– Never park your motorcycle in places where there exist fire hazards due to dry grass or
other easily flammable materials.
– Always take out the ignition key when parking your motorcycle so that it cannot be used
by unauthorized persons.
– The side stand is dimensioned for the weight of the motorcycle only. Sitting on the motor-
cycle will increase the weight on the side stand. The side stand or engine case can be
damaged and the motorcycle can tip over.
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING INSTRUCTIONS »
30
Fuel
In the condition at delivery, the LC8 engine requires unleaded fuel with at least RON 95
(USA = Premium PON 91, see technical specifications – engine).
After refueling, it will take approx. 3 minutes for the fuel warning lamp to switch off and for
TRIP F to automatically reset to 0 and return to the previous display mode.
NOTE:
MAX
Press the SET key for 2 seconds to immediately turn off the fuel warning lamp.
This motorcycle is equipped with a catalytic converter that will be destroyed if you use leaded
fuel. Always use unleaded fuel.
Fuel expands when its temperature rises. Therefore do not fill the tank to the top (see fig.).
Gasoline is highly flammable and poisonous. Extreme caution should be used when han-
dling gasoline. Do not refuel the motorcycle near open flames or burning cigarettes. Always
switch off the engine before refuelling. Be careful not to spill gasoline on the engine or exhaust
pipe while the engine is hot. Wipe up spills promptly. If gasoline is swallowed or splashed
in the eyes, seek a doctor’s advice immediately.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE SCHEDULE »
32
1st Service
after
1000 km
every
every
990 SUPER DUKE / R 2007
A clean motorcycle can be checked more quickly which saves money!
7500 km
or
15000 km
or
once a year
every 2 years
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
Change engine oil and oil filter
Clean oil screens of engine and oil tank
Clean magnetic drain plugs of engine and oil tank
Check oil lines for damage and kink-less arrangement
Renew spark plugs
z
z
z
Check and adjust valve clearance
z
z
Check engine fastening bolts for tight fit
Check all engine bolts accessible from the outside for tight fit
Check clutch linings
Check clutch pressure booster system
Clean the oil jet for the clutch lubrication
Check rubber boots for cracks or leaks
Check fault memory with the KTM diagnosis tool
z
z
z
z
z
Perform a status check of neutral, clutch, 2nd/3rd gear and side stand switch
using the KTM diagnosis tool
z
z
Make sure the fuel hose, hoses on the vacuum sensors, SAS hoses and vent
hoses are run correctly and check for damage
z
z
z
z
z
z
z
z
Replace the O-ring on the fuel hose connection and check for leaks
Check the wiring harness on the throttle body for proper installation
and damage
z
z
z
z
z
z
Check cooling system for leaks and antifreeze protection
Check radiator fan for proper operation
Check the exhaust system for leaks and correct suspension and the clamps
for a tight fit
z
z
z
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE SCHEDULE »
33
1st Service
after
1000 km
every
every
990 SUPER DUKE / R 2007
A clean motorcycle can be checked more quickly which saves money!
7500 km
or
15000 km
or
once a year
every 2 years
z
Replace the graphite gasket in the rear exhaust manifold slide
Check actuating cables for damage, smooth operation, and kink-less arrange-
ment,adjust and lubricate
z
z
z
z
z
z
z
z
Check the oil level in the hydraulic clutch reservoir
Check air filter, renew if necessary, clean air filter box
Check cables for damage and kink-less arrangement
Check headlamp adjustment
z
z
z
z
Check electrical system for function (low/high beams, stop light, turn indica-
tors,headlamp, flasher, tell-tale lamps, speedometer illumination, horn, side-
stand switch, clutch switch, emergency-off switch)
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
Make sure all bolts and nuts are tight
Check brake fluid level, lining thickness, and brake discs
Change brake fluid
z
z
z
z
z
z
z
z
z
z
z
z
Check brake lines for damage and leaks
Check/adjust smooth operation, free travel of handbrake/footbrake levers
Check bolts of brake system for tight fit
Check shock absorber and fork for leaks and proper operation
Clean fork dust sleeves
z
z
z
Bleed fork legs
Check swinging-fork pivot
Check/adjust steering-head bearing
Check all chassis bolts for tight fit (fork plates, fork leg, axle nuts/bolts,
swinging-fork pivot, reversing lever, shock absorber)
z
z
z
Download from Www.Somanuals.com. All Manuals Search And Download.
34
PERIODIC MAINTENANCE SCHEDULE »
1st Service
after
1000 km
every
every
990 SUPER DUKE / R 2007
A clean motorcycle can be checked more quickly which saves money!
7500 km
or
15000 km
or
once a year
every 2 years
z
z
z
z
z
z
z
z
z
Check rim joint
Check tire condition and inflation pressure
Check chain, sprockets and chain guides for wear, force fit and tension
Check bolts on pinion and chain sprocket for locking devices
and a tight fit
z
z
z
z
z
z
z
z
Lubricate chain
Check wheel bearings and jerk damper for play
IF MOTORCYCLE IS USED FOR COMPETITION 7500 KM SERVICE SHOULD BE CARRIED OUT AFTER EVERY RACE!
Service intervalls should never be exceeded by more than 500 km.
Maintenance work performed by an authorized KTM workshop is not a substitute for care and maintenance by the driver!
990 SUPER DUKE / R 2007
ADDITIONAL SERVICE WORK TO BE PERFORMED UNDER A SEPARATE ORDER
at least
once a year
every 15000 km
or every 2 years
z
Perform complete fork maintenance
z
Perform complete shock absorber maintenance
Clean and lubricate steering-head bearing and sealing elements
Treat the electrical contacts and switches with contact spray
Treat battery connections with contact grease
Change coolant fluid
z
z
z
z
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE SCHEDULE »
35
990 SUPER DUKE / R 2007
VITAL CHECKS AND CARE PROCEDURES TO CONDUCTED BY THE OWNER OR THE MECHANIC
before
each start
after
every cleaning
every
1000 km
z
Check oil level
z
z
z
z
Check brake fluid level
Check brake pads for wear
Check lighting system for proper operation
Check horn for proper operation
Lubricate actuating cables and nipples
Bleed fork legs
z
z
z
z
z
Clean chain
Lubricate chain
z
z
z
z
z
Check chain tension
Check tire pressure and wear
Check coolant level
Check fuel lines for leaks
Check all control elements for smooth running
Grease the hand brake lever and clutch lever
Check brake performance
z
z
z
Treat exposed metal components (except for the braking and exhaust
system) with wax-based anti-corrosion agents
z
z
Treat ignition/steering lock and light switch with contact spray
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
36
– Do not clean the motorcycle with a power washer otherwise water will get into the bearings, electric socket connectors, etc.
– Use special KTM screws with the correct thread length to fasten the spoiler to the tank. Mounting other screws or longer screws could
puncture the tank and cause fuel to leak out.
– If you disconnect socket connectors with self-locking nuts, replace them before remounting. If no new self-locking nuts are available,
apply Loctite 243 to the thread of the old nuts. If the thread is damaged, replace the screws and nuts.
– Do not use toothed disks or split washers for the engine fastening bolts since they will work their way into the frame components and
become loose. Always use self-locking nuts.
– Let the motorcycle cool down before servicing to avoid being burned.
– Properly dispose of oils grease, filters, fuel, cleansers, etc. Observe the regulations effective in your country.
– Never pour used oil in the sewer or dispose of it outdoors. 1 liter of used oil will pollute 1,000,000 liters of water.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
37
Adjusting the fork and shock absorber
Super Duke
Super Duke R
There are a number of ways to adjust the fork and shock absorber to match the chassis to
your driving style and the payload.
We have provided a table with pragmatical values to help you tune up your motorcycle. These
tune-up specifications are reference values only and should serve as a basis for your per-
sonal chassis and suspension tuning. Do not make arbitrary changes to the settings (maxi-
mum ±40%) since this may impair the handling characteristics (particularly in the high-
speed range).
BASIC SETTING
FORK WP 4860 ROMA
Compression adjuster (clicks) 20 15 10 10 18 18 14 18
Make sure both fork legs are equally adjusted.
A sticker with the basic settings is located under the seat.
Rebound adjuster (clicks) 20 15 10 10 16 16 12 16
Spring preload (turns)
5
5
5
5
5
5
5
5
Adjusting compression damping of fork
Hydraulic compression damping determines the reaction when the fork is compressed.
Turn the adjusting screws [1] clockwise to increase damping, turn it counterclockwise to
reduce damping during compression. Make the same damping rate adjustment to both fork
legs.
STANDARD ADJUSTMENT
1
– Turn adjusting screw clockwise as far as it will go.
– Super Duke: Turn 15 clicks in a counterclockwise direction.
– Super Duke R: Turn 18 clicks in a counterclockwise direction.
Adjusting rebound damping of fork
Hydraulic rebound damping determines the reaction when the fork is rebound. By turning
the adjusting screw [2] (REB), the degree of damping of the rebound can be adjusted. Turn
the knob clockwise to increase damping, turn it counterclockwise to reduce damping dur-
ing rebounding. Make the same damping rate adjustment to both fork legs.
2
STANDARD ADJUSTMENT
– Turn adjusting screw clockwise as far as it will go.
– Super Duke: Turn 15 clicks in a counterclockwise direction.
– Super Duke R: Turn 16 clicks in a counterclockwise direction.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
38
Adjusting the spring preload on the fork
The fork spring preload can be adjusted by turning the adjusting screws [2] (wrench size 24
mm) ± 5 mm (0,2 in).
1
Turning in a clockwise direction will increase the preload, turning in a counterclockwise direc-
tion will decrease the preload. 1 turn will change the preload by 1 mm.
Changing the preload will not affect the rebound damping adjustment, although adjusting
screw [1 will turn at the same time. Make the same spring preload adjustments to both fork
legs.
2
Generally, if the preload is higher, the rebound damping should also be set higher.
STANDARD ADJUSTMENT:
– Turn adjusting screw counterclockwise as far as it will go.
– Turn 5 turns in a clockwise direction.
Super Duke
Super Duke R
BASIC SETTING
SHOCK ABSORBER
WP 4618 BAVP
Compression adj. Low Speed (clicks) 25 20 10 10 20 16 10 16
Compression adj. High Speed (turns)
2
1.5
Rebound adjuster (clicks) 20 12
Spring preload (mm)
1
8
6
1
8
6
2.5 1.5
1
8
5
1,5
12
5
12 12
6
6
5
5
Compression damping of shock absorber
The shock absorber can synchronize the compression damping in the low and high-speed
range separately (Dual Compression Control).
Low and high speed refers to the movement of the shock absorber during compression and
not to the speed of the motorcycle.
The low and high-speed technology overlaps.
The low-speed setting is primarily for slow to normal shock absorber compression rates.
The high-speed setting is effective at fast compression rates.
Turning in a clockwise direction will increase the damping, turning counterclockwise will
decrease the damping.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
39
STANDARD ADJUSTMENT LOW-SPEED:
– Turn adjusting screw [1] clockwise as far as it will go.
– Turn 20 clicks in a counterclockwise direction.
1
STANDARD ADJUSTMENT HIGH-SPEED:
– Turn adjusting screw (wrench size 17 mm) clockwise as far as it will go.
– Super Duke: Turn 1.5 turns in a counterclockwise direction.
– Super Duke R: Turn 2.5 turns in a counterclockwise direction.
The damping unit of the shock absorber is filled with high-compression nitrogen. Never try
to take the shock absorber apart or to do anymaintenance work yourself. Severe injuries could
be the result.
Never unscrew the black screw connection (24mm).
Rebound damping of shock absorber
By using the adjusting screw [2], the degree of damping of the rebound can be adjusted.
Turn the knob in a clockwise direction to increase damping, turn it in a counterclockwise
direction to reduce damping during rebounding.
STANDARD ADJUSTMENT:
– Turn adjusting screw [2] clockwise as far as it will go.
– Turn 12 clicks in a counterclockwise direction.
2
The damping unit of the shock absorber is filled with high-compression nitrogen. Never try
to take the shock absorber apart or to do any maintenance work yourself. Severe injuries
could be the result.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
40
Checking the chain tension
Place the motorcycle on the side stand. Switch the transmission to neutral and push
the chain up. The distance between the chain and the swing arm should be 7 mm when
the upper part of the chain [1] is tensioned (see drawing). Correct the chain tension if
necessary.
1
7 mm
–
If chain tension is too great, parts within the secondary power transmission (chain, chain
sprockets, transmission and rear wheel bearings) will be subjected to unnecessary stress,
resulting in premature wear and even chain breakage.
– Too much slack in the chain, on the other hand, can result in the chain jumping off the
chain wheels. If this happens, the chain could also block the rear wheel or damage the
engine.
– In either case the operator is likely to lose control of the motorcycle.
4
2
3
5
Correcting the chain tension
Loosen the collar nut [2], loosen the counternuts [3] and turn the left and right adjustment
screws [4] the same distance. Tighten the counternuts [3].
5
To make sure the rear wheel is aligned, the marks on the chain tensioners must be in the
same position on the left and right in relation to the reference marks [A]. Before tightening
the wheel spindle make sure the chain tensioner [5] rests against the adjustment screws
and the rear wheel is aligned with the front wheel.
Tighten the collar nut [2] to 90 Nm.
If you don’t happen to have a torque wrench at hand, make sure you have the tightening
torque corrected by a KTM dealer as soon as possible. A loose axle may lead to an unstable
Download from Www.Somanuals.com. All Manuals Search And Download.
A
driving behavior of your motorcycle.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
41
Chain maintenance
Maintenance of the X-ring chain is reduced to a minimum. Rinse off any heavy dirt with
plenty of water. Residual used grease must be removed prior to lubrication (Motorex Chain
Clean 611). After drying, use a chain spray specially designed for X-ring chains (Motorex
Chainlube 622).
– No lubrication is allowed to reach the rear tire or the brake disk, eitherwise the road
adherence and the rear wheel braking effects would be strongly reduced and the motor-
cycle could easily get out of control.
– The chain does not have a chain joint for safety reasons. Always have the chain replaced
in an authorized KTM workshop where the service technicans have the required riveting
tool.
– Never mount a normal chain joint.
Also check sprockets and chain guides for wear, and replace if necessary.
15 KG
Checking the chain for wear
To check the chain for wear proceed as follows:
Switch the transmission to idle and put a load of approx. 15 kilograms
(33 lbs) on the lower part of the chain (see illustration). Now measure the distance between
18 chain rollers on the upper part of the chain. The chain needs to be replaced when the
distance is 272 mm (10.70 in). Since chains do not always wear evenly, repeat the meas-
urement at different parts of the chain.
max. 272 mm
Replace the chain if any X-rings are missing.
1
2
3
16 17 18
NOTE:
If you mount a new chain, the sprockets should also be replaced. New chains wear faster if
used on old used sprockets.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
42
General information on KTM disk brakes
1
BRAKE CALIPERS:
The front brake calipers [1] have 4 brake pistons and are radially bolted to the fork legs.
The front brake disks are designed as „floating“ brake disks, i.e. they are not firmly con-
nected to the front wheel.
2
The lateral balance ensures that the brake pads always have the best possible contact to the brake
disk. Apply Loctite 243 to the screws [2] on the brake caliper support and tighten to 45 Nm.
The rear brake caliper [3] has 1 brake piston and is designed as a „floating brake caliper“,
i.e. it is not firmly connected to the brake caliper support. The lateral balance ensures that
the brake pads always have the best possible contact to the brake disk.
LOCTITE 243
For safety reasons, always have maintenance work and repairs to the brake system performed
by an authorized KTM workshop.
3
BRAKE PADS:
Your motorcycle is equipped with sintered brake pads in the front and rear and homologated
accordingly. They guarantee maximum braking performance.
Front brake pads:
Rear brake pads:
HAWK 7342-49
TOSHIBA TTH 38 GF
Brake pads available in the accessory trade are often not authorized for operation of your
KTM motorcycle in road traffic. The brake pads design and friction factor and therefore the
braking power can deviate significantly from original KTM brake pads. If you use different
brake pads than those provided with the original equipment, it cannot be warranted that
they are authorized for use in road traffic. Your motorcycle will not longer comply with the
regulations authorizing the use of vehicles for road traffic and the warranty will be void.
BRAKE FLUID RESERVOIRS:
The brake fluid reservoirs on the front and rear wheel brakes have been designed in such a
way that even if the brake pads are worn it is not necessary to top up the brake fluid. There
is no reason to remove the reservoir cap under normal conditions. If the brake fluid level
drops below the minimum either the brake system has a leak or the brake pads are com-
pletely worn down. In this case, consult an authorized KTM dealer immediately.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
43
BRAKE FLUID:
We recommend that you use Motorex DOT 5.1 brake fluid when you refill or change the brake
fluid. DOT 5. 1 brake fluid has a wet boiling point of 180°C / 356°F (25°C / 45°F higher
than DOT 4) and is safer for high performance applications. Brake fluid DOT 5.1 is a poly-
ethylene glycol based fluid, amber-colored and can be mixed with DOT 4 brake fluid. Do
not, in any event, use DOT 5 brake fluid. It is based on silicone oil and is dyed purple. KTM
motorcycle gaskets and brake hoses are not designed for DOT 5 brake fluid.
Brake fluid is exposed to a high thermal load and absorbs moisture from the air, which low-
ers the boiling point. The brake fluid should therefore be changed at the prescribed
intervals.
Have the brake fluid for the front and rear brake changed at an authorized KTM workshop
every 2 years.
BRAKE DISCS:
Wear reduces the thickness of the brake disc in the area of contact [4] with the brake pads.
The brake disk should not be thinner than 4 mm (0.16 in) at the weakest point [A]. Check
the wear at several points.
A
Brake disks that are less than 4 mm (0.16 in) thick are a safety hazard. Have worn brake
disks replaced immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
44
Adjusting the basic position of the hand brake lever
The basic position of the hand brake lever can be modified by turning the adjusting screw
[1]. This lets you adapt the position of the pressure point (the resistance you feel on the
hand brake lever when the brake pads are pressed against the brake disk) to fit any hand.
1
min. 3 mm
At the hand brake lever, free travel must at least be 3 mm (0.12 in). Only then may the pis-
ton in the hand brake cylinder be moved (to be recognized by the greater resistance of the
hand brake lever). If this free travel is not provided, pressure will build up in the braking
system, and the front wheel brake may fail due to overheating.
Checking the front brake fluid level
The brake fluid reservoir for the front brake is located on the left side of the handlebar and
has a „MIN“ and a „MAX“ mark. The brake fluid level may not fall below the „MIN“ mark
when the vehicle is parked in a vertical position.
– If the brake fluid level drops below the minimum either the brake system has a leak or
the brake pads are completely worn down. In this case, consult an authorized KTM dealer
immediately.
– Have the brake fluid changed at an authorized KTM workshop every 2 years.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
45
Checking the front brake pads
The brake pads can be inspected from the rear. The linings must be at least 1 mm (0.04
in) thick.
min.
1 mm
At their most worn point brake pad linings should not be thinner than 1 mm, otherwise they
could lead to brake failure. For your own safety don’t put off having your brake pads changed.
If the brake pads are replaced too late when the lining is partly or completely worn off, the
steel parts on the brake pads will grind against the brake disks. This significantly decreases
the braking effect and destroys the brake disks.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
46
Checking the rear brake fluid level
The brake fluid reservoir for the rear brake is located on the rear right of the vehicle and has
a "MIN" and a "MAX" mark. The brake fluid level may not fall below the "MIN" mark when
the vehicle is parked in an upright position.
– If the brake fluid level drops below the minimum either the brake system has a leak or
the brake pads are completely worn down. In this case, consult an authorized KTM dealer
immediately.
– Have the brake fluid changed at an authorized KTM workshop every 2 years.
Checking the rear brake pads
The brake pads can be inspected from the rear. The thickness of the linings may not be less
than 1 mm (0.04 in).
min.
1 mm
At their most worn point brake pad linings should not be thinner than 1 mm, otherwise they
could lead to brake failure. For your own safety don’t put off having your brake pads changed.
If the brake pads are replaced too late so that the lining is partly or entirely worn away, the
steel components of the brake pad will rub against the brake disc, imparing the braking
effect and destroying the brake disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
48
Dismounting and remounting the front wheel
Special stands are required to dismount the wheels to make sure the motorcycle is securely
fixed. The front stand only adequately fixes the motorcycle together with the rear stand. The
stands shown in the illustration can be found in the KTM Power Parts catalog.
First mount the rear, then the front stand. Make sure the stands rest on solid ground and
are correctly mounted. The front wheel should not touch the ground.
NOTE FOR SUPER DUKE R:
First remove the crash pads.
Remove the screws [1] on the left and right brake caliper and carefully pull the brake calipers
and bushings [6] off the brake disks towards the back.
6
1
2
Loosen the collar screw [2] and the clamping screws [3] on both fork leg axle passages.
Unscrew the collar screw approx 8 turns, press on the collar screw with your hand to push
the wheel spindle out of the fork leg axle passage and remove the collar screw. Hold the
front wheel while you pull out the wheel spindle.
2
3
Lift the front wheel off the fork.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
49
Take the left [4] and right distance bushing out of the shaft seal rings.
4
– Do not operate the hand brake when the front wheel has been dismounted.
– Be careful not to damage the brake disks when you lay the front wheel down.
A
Before you remount the front wheel, clean and grease the shaft seal rings [5] and the bear-
ing surface [A] of the distance bushings and mount the distance bushings (wide distance
bushing in the left shaft seal ring). When mounting the distance bushing, be careful not to
press the sealing lips towards the inside. position the front wheel according to the running
direction shown by the arrows [B] on the rim.
5
To mount, lift the front wheel in the fork and mount the wheel spindle and collar screw [2].
Tighten the collar screw to 60 Nm. Position the brake calipers and bushings [6] and make
sure the brake pads are correctly seated. Apply Loctite 243 to the screws [1], mount the
screws and tighten to 45 Nm.
Take the motorcycle off the front stand, actuate the front wheel brake and vigorously com-
press the fork several times to align the fork legs.
B
Before you tighten the clamp screws [3] check whether the right brake disk [C] runs in the
center of the brake caliper. Move the right fork leg to the side if necessary, then tighten the
clamp screws on both fork leg axle passages to 15 Nm. Actuate the hand brake until you
feel the pressure point and check whether the front wheel can easily be turned. Remove the
rear stand.
– If you do not have a torque wrench to mount the wheel, have the torques corrected by
an authorized KTM workshop as soon as possible. A loose wheel spindle can cause the
motorcycle's handling performance to become instable and cause it to crash.
– After mounting the front wheel, keep operating the hand brake until the pressure point
returns.
C
C
– Always keep the brake disks free from oil and grease, otherwise the braking effect will
be significantly reduced.
NOTE FOR SUPER DUKE R: remount the crash pads.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
50
Dismounting and mounting the rear wheel
Special stands are required to dismount the wheels to make sure the motorcycle is securely
fixed. The stands shown in the illustration can be found in the KTM Power Parts catalog.
Mount the rear stand. Make sure the stand rests on solid ground and is correctly mounted.
The rear wheel should not touch the ground
NOTE FOR SUPER DUKE R:
First remove the crash pads.
Unscrew the collar nut [1], remove the chain tensioner [2], hold the rear wheel while you
pull out the wheel spindle [3]. Push the rear wheel forward as far as possible and remove
the chain from the rear sprocket. Carefully take the rear wheel off the swing arm.
1
– Do not operate the rear brake when the rear wheel has been dismounted.
– Always place the wheel on the ground with the brake disc pointing upwards. Otherwise
the brake disc may be damaged.
– If the axle is dismounted, clean the thread of the wheel spindle and collar nut thoroughly
and apply a new coat of grease (Motorex Long Term 2000) to prevent the thread from
jamming.
Before remounting the rear wheel, clean and grease the bearing surface of the bushings [5]
and the shaft seal ring [6].
2
4
The rear wheel is remounted in the reverse order. Make sure the chain tensioners [4] are
mounted in the same way on the left and right. The marks on the chain tensioners must be
in the same position on the left and right in relation to the reference marks [A]. Before you
tighten the collar nut to 90 Nm, press the rear wheel towards the front to allow the chain
tensioner to rest against the clamping screws.
3
A
NOTE FOR SUPER DUKE R: remount the crash pads.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
51
– If you don’t happen to have a torque wrench at hand, make sure you have the tighten-
ing torque corrected by a KTM dealer as soon as possible. A loose wheel spindle may
lead to an unstable driving behavior of your motorcycle.
– After mounting the rear wheel, keep operating the footbrake until the pressure point returns.
– It is very important to keep the brake disk free from oil and grease, otherwise the brak-
ing effect would be strongly reduced.
6
5
Tires, air pressure
Tire type, tire condition, and how much air pressure the tires have in them affect the way
your motorcycle rides, and they must therefore be checked whenever you’re getting ready to
go anywhere on your motorcycle.
For driving safety and maximum handling, only use tires authorized by KTM (tire releases
240 KPH). Other tires can have a negative effect on the motorcycle's handling (e.g. can
cause it to „wobble“ at higher speeds).
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
52
– Tire type and size can be found in the technical specifications and in the homologation
certificate.
TIRES – AIR PRESSURE
990 Super Duke / R front
rear
– Tire condition has to be checked every time you want to ride your motorcycle. Before
leaving check for punctures and nails or other sharp objects that might have become
embedded in the tire.
Road, driver only
2.4 bar 2.4 bar
34 psi 34 psi
Road, with passenger 2.4 bar 2.6 bar
34 psi 37 psi
2.4 bar 2.6 bar
34 psi 37 psi
– Refer to the specific regulations in your country for minimum tire tread requirements.
We recommend replacing tires at the latest when the tread is down to 2 mm (0.08 in).
– Tire pressure should be checked regularly on a „cold“ tire. Adapt the air pressure to the
motorcycle's total weight. Proper pressure ensures optimum driving comfort and extends
the life of your tires.
maximum payload
– Worn tires can have a negative effect on
how your motorcycle performs, especially
on wet surfaces.
– If air pressure is too low, abnormal wear
and overheating of the tire can result.
new tires, tilting the vehicle at different
angles so that all sections are properly
roughened. Tires will not display their full
grip characteristics until they are properly
run in.
– For reasons of safety, it is recommended
to exchange the valve insert whenever a
new tire is mounted.
– Do not mount tires which have not been
approved by KTM. Other tires could have
adverse effects on the way your motorcy-
cle rides.
– Use tires of the same brand and type for
the front and rear wheels.
–
New tires have a smooth surface, which
means that they must be run in to achieve
full grip. For this purpose, ride the motor-
cycle carefully at moderate speed during
the first 200 kilometers (125 miles) with
– For your own safety replace damaged tires
immediately.
Battery
The battery is located in the front spoiler in front of the engine and is maintenance-free. It
is not necessary to check the electrolyte level or to refill water. Simply keep the battery poles
clean and slightly grease them with an acid-free grease if necessary. The charge condition
and type of charge are very important for the battery's service life.
1
Never operate the motorcycle with a run-down battery or without the battery. This can dam-
age the electronic components or safety equipment in either caseand the motorcycle will no
longer be roadworthy.
Never remove the closing cover [1] otherwise the battery will be damaged.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
53
Removing and remounting the battery
The battery only needs to be removed if the motorcycle is being immobilized.
Remove the screws [1] on both sides, loosen the screws [2] 2 turns and remove the front
spoiler towards the front. Push the cables to the side. Remove the screws [3] and fold the
battery cover [4] down.
First disconnect the negative terminal, then the positive terminal from the battery. Make
sure the battery terminals are not bent when they are removed.
Remove the battery cover and take out the battery.
Charge the battery before and after storage. Storage temperature 0 - 35°C (32 - 95°F).
When remounting the battery, position it in the battery compartment and mount the battery
cover. First connect the cables on the positive terminal, then connect the negative terminal
to the battery to avoid a short-circuit. Open the battery cover and fasten with 2 screws. Remount
the front spoiler. Apply Loctite 243 to the screws [1] and tighten to 10 Nm.
1
2
2
– If electrolyte (sulphuric acid) leaks from the battery, proceed with great care. The elec-
trolyte can cause severe burns.
3
– In the case of skin contact rinse thoroughly with water.
– In the case of contact with the eyes, thoroughly rinse eyes with water for at least 15 min-
utes. Immediately consult a doctor.
– The battery is a closed model but can nevertheless emit explosive gases. Avoid sparks
and open fire near the battery.
3
– Defective batteries must be stored out of the reach of children. Ensure proper disposal
of discarded batteries.
– The screws on the underride protection must be secured with loctite 243 to prevent them
from becoming loose.
Never disconnect the battery while the engine is running. This will destroy the rectifier-reg-
ulator.
4
STORAGE:
If the motorcycle is being immobilized for longer periods of time, remove and charge the
battery. Storage temperature 0 - 35°C (32 - 95°F), avoid direct sunlight.
Charge the battery every 3 months.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
54
Charging the battery
The battery discharges every day, even if it is not used.
Always disconnect the battery when charging. Charge the battery as described in the instruc-
tions [1] on the battery housing. Do not exceed the amperage and charging time. Quick charg-
ing at a high amperage has an adverse effect on the service life.
To charge the battery while mounted, always use the KTM battery charger (Item no.
58429074000) to ensure that the electric system is not damaged by excess voltage. Always
remove the battery if using other battery chargers! You can also use this charging device to
test the off-load voltage and startability of the battery and generator. It is impossible to over-
charge the battery with this device.
1
Charge the battery immediately if it is empty when you start the motorcycle. If left to stand
in an uncharged condition for a longer period of time, the battery will run down and sulfa-
tize, destroying the battery.
Recharge the battery every 3 months if it is being stored for a longer period of time.
– Never remove the closure since it will be damaged.
– To avoid damage to the on-board electronic system, always disconnect the minus pole
before you charge the battery.
– To charge, connect the battery to the battery charger before you switch on the battery
charger. When the battery is charged, switch off the battery charger before you discon-
nect the battery.
– Provide adequate ventilation when charging the battery in a closed room; the battery
emits explosive gases when charging.
– Electrolytes will escape through the safety valves if the battery is charged too long or at
an excessive voltage or amperage. This will reduce battery capacity.
– Try to avoid quick charges.
VOLT
Jump start
Jump starts are not recommended since they can damage the motorcycle's electronic
system.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
55
Main fuse
The main fuse protects all of the motorcycle's electric power consumers. The main fuse is
located on the left under the front spoiler.
1
2
Pull the connector [1] out of the bracket, remove the cap [2] and check the main fuse [3].
A spare fuse [4] (30 amperes)is also plugged into the bracket.
Always replace blown fuses with an equivalent fuse. Visit an authorized KTM workshop if a
new fuse blows again after it is inserted.
4
Never use a stronger fuse or a repaired fuse. Improper use can destroy the entire electric
system.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
56
Fuses for individual power consumers
A fuse box is mounted under the seat containing additional fuses that protect the individ-
ual electric power consumers.
The power consumers are listed numerically on the cover of the fuse box [1] and allocated
as described below. Spare fuses [2] with 10 and 15 amperes are also found in the fuse box.
1
2
NO
CONSUMER
AMPERES
1 . . . . . . . . . Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2 . . . . . . . . Light (high beam, low beam, parking light) . . . . . . . . . . . . . . . . . . . . .15
3 . . . . . . . . . Horn, brake light, combined instrument . . . . . . . . . . . . . . . . . . . . . . .10
4 . . . . . . . . . Fuel pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5 . . . . . . . . . Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
6 . . . . . . . . . Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7 . . . . . . . . . Main relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
8 . . . . . . . . . ACC1 for attachments (switched with the ignition) . . . . . . . . . . . . . . . .10
9 . . . . . . . . . ACC2 for attachments (positive supply) . . . . . . . . . . . . . . . . . . . . . . . .10
10 . . . . . . . . –
3
SPARE . . . . . Spare fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 15
Replace a blown fuse only with an equivalent one. If a new fuse that has just been set in
gets blown again, you are strongly advised to have it inspected by a KTM dealer.
Under no circumstances is a stronger fuse allowed to be set in or a fuse allowed to be “repaired”.
An inexpert treatment could damage the whole electrical installation!
The ACC1 and ACC2 fuses [3] are designed for attachments with a maximum power con-
sumption of 10 amperes. The respective connector for this equipment is located in the head-
light mask. Ask your authorized KTM workshop for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
57
Replacing the headlight lamp
Remove the screws [1] on the left and right and tilt the headlight mask down towards the
front.
Never touch the glass of the bulb with your fingers. The glass of the bulb must remain absolutely
free from grease. Heat will otherwise cause the grease to evaporate and settle down on the
reflector.
1
1
BULB FOR HIGH BEAM [A]:
2
A
Remove the rubber cap [2] and pull off the connector [3]. Detach the retaining clip and
4
3
remove the bulb.
5
Insert a new bulb, attach the retaining clip, connect the connector and mount the rubber
cap.
BULB FOR LOW BEAM [B]:
Remove the rubber cap [4] and pull off the connector [5]. Detach the retaining clip and
remove the bulb.
When you insert the new bulb, make sure the tab fits in the corresponding recess in the
socket.
B
Attach the retaining clip, connect the connector to the bulb and mount the rubber cap.
PARKING LIGHT BULB [C]:
Loosen the AH screw SW4 [6] and push the right mask spoiler aside. Pull out the bulb socket
[7] and pull the light bulb out of the socket.
C
Mount the light bulb in the reverse order.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
58
USA design:
The parking light [E] is located in the upper part of the headlight in the USA design. Bulb
[F] (see Technical specifications – Chassis / Lighting) with high and low beams is mounted
in the lower part of the headlight.
F
E
Connect the connectors to the connector support to check all of the bulbs for proper func-
tioning before you remount the headlight.
Adjusting the headlight range
The payload can make it necessary to correct the headlight range.
The headlight range can be adjusted with the adjusting screw [1]. Turning in a clockwise
direction will increase the headlight range, turning in a counterclockwise direction will
reduce the headlight range.
1
CONTROL:
Make a mark on a light colored wall behind a horizontal surface, at the height correspon-
ding to the center of the headlight. Position your motorcycle 5 meters (16.4 ft) from the
wall in a fully loaded condition (baggage, driver, passenger) and switch on the low beam.
The light/dark cut-off should be 5 cm (2 in) under the mark (see drawing).
5 m
5 cm
x
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
59
Replacing the brake light and taillight bulbs
NOTE:
Only mount red light bulbs in a smoked brake tail light.
1
Remove the seat.
BULB FOR BRAKE LIGHT:
Turn the bulb socket [1] approx. 30° in a counterclockwise direction and pull it out of the
taillight housing. Slightly press in the bulb, turn approx. 30° in a counterclockwise direc-
tion and remove it from the socket.
Proceed in the reverse order to mount a new bulb.
BULB FOR THE TAILLIGHT:
Remove the bulb socket [2] from the housing and pull the bulb out of the socket. Insert a
new bulb and press the bulb socket all the way into the taillight housing.
2
Mount the seat.
Replacing the flasher bulbs
Remove the screw on the back of the turn signal, carefully fold the lens [3] towards the
motorcycle and remove.
Slightly depress the bulb, turn it approx. 30° counterclockwise and pull it out of the socket.
To mount the lamp reverse the worksteps indicated above.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
60
Cooling system
The water pump in the engine ensures a forced circulation of the cooling liquid. When the
engine is cold, the cooling liquid only circulates in the cylinders and cylinder heads. The
thermostat will open when the engine reaches approx. 75°C (167°F) and the cooling liquid
will also be pumped through the aluminum radiator.
Cooling is by means of the air stream. The lower the speed, the lower the cooling effect.
Soiled cooling fins also impair the cooling effect.
If, for example, slow urban traffic or waiting at a traffic light cause little or no air to stream
through the radiator, the temperature of the cooling liquid will rise. The radiator fan [1] switches
on when the cooling liquid reaches a temperature of 102°C (216°F). Additional air is blown
through the radiator to prevent the cooling system from overheating.
1
The temperature indicator [2] will begin to blink and the red cooling liquid temperature warn-
ing lamp [3] will light up when the cooling liquid reaches approx. 120°C (248°F), having
exceeded the normal operating temperature. Possible causes:
2
– Slow riding with large loads at a higher air temperature:
If possible increase your running speed, so that more air can blow through the radiators.
Should the warning light still be on off after 1500 meters (1 mile), stop immediately,
switch off the engine and look for other possible causes.
3
– The cooling fan on the radiator is not working:
The cooling fan must be running, when the cooling liquid temperature is 120°C (248°F)
and the ignition is on. If the fan is not working, and there appears to be sufficient cool-
ing liquid, the only thing you can do is to drive on to your nearest authorized KTM work-
shop at the least possible engine load.
– Too little cooling liquid in the system:
Check whether any cooling liquid is leaking out (also on the bottom of the motorcycle).
Let the engine cool down and check the cooling liquid level in the radiator (see chapter
Checking the cooling liquid level in the radiator). Only continue to drive if there is enough
cooling liquid in the system. Contact an authorized KTM workshop to have the error elim-
inated. You will damage the engine if you continue to drive when the cooling liquid tem-
perature warning lamp is on.
– Excessive use of the clutch at slow speed
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
61
A mixture of 50% antifreeze and 50% distilled water is used as the cooling liquid. How-
ever, the anti-freeze protection must be at least -25° C (-13° F). Aside from antifreezing pro-
tection, this mixture also provides great corrosion protection which is why it must not be
replaced by pure water.
4
–
For the cooling system, use only high-grade antifreezer (Motorex Anti-Freeze). Using
lowergrade antifreeze agents, can cause corrosion and coolant foaming.
– More antifreeze must be added if you plan to travel to a region where temperatures are
expected to drop below -25°C (-13°F).
Pressure induced by heating of the cooling liquid in the cooling system is controlled by a
valve in the radiator cap [4]; a water temperature rising up to 125° C (257° F) is admissi-
ble, without fear of problems.
Any excess cooling liquid caused by thermal expansion is conducted to the compensating
tank [5]. It will be sucked back in as soon as the temperature in the cooling system drops.
5
Checking the cooling liquid level in the compensating tank
Check the level of the cooling liquid when the engine is cold. It should fall between the MIN
and MAX marks on the compensating tank [6].
Add cooling liquid (see above for mixture ratio) if the cooling liquid level drops below the
MIN mark.
If you need to add cooling liquid quite often, the cooling system may leak. If the compen-
sating tank is empty, also check the cooling liquid level in the radiator. Have the cooling
system checked by an authorized KTM workshop.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
62
Checking the cooling liquid level in the radiator
Hold the radiator cap [1] with a cloth, carefully turn in a counterclockwise direction and
remove. The radiator should be completely filled with cooling liquid; no air should be in the
radiator.
If any cooling liquid is missing, the cooling system is probably leaking. Have the cooling
system checked at an authorized KTM workshop.
2
1
If possible, check the cooling liquid level when the engine is cold. If you need to remove
the radiator cap when the engine is hot, hold the cap with a cloth and open slowly, allow-
ing any excess pressure to escape (danger of scalding).
– Accumulated soil and lime on the radiator cap will cause you to lose cooling liquid. Carefully
clean the radiator cap, gasket [2] and sealing area each time.
– If more than 1 liter of cooling liquid needs to be added, you will need to bleed the cool-
ing system.
Bleeding the cooling system
Take off the left and right spoilers. To take off the spoilers, remove the screws [3] and [4]
on each side.
3
3
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
63
Remove the bleeder screw [5] on the left side of the radiator.
5
To completely bleed the cooling system, the motorcycle must be raised approx. 50 cm (20
in) in the front.
Add cooling liquid until it runs out of the vent holes without bubbles and immediately mount
the screw to prevent air from entering the radiator.
Completely fill the radiator with cooling liquid. Mount the radiator cap and move the motor-
cycle into a horizontal position again. Now fill the compensating tank [6] with cooling liq-
uid until it reaches a level between the MIN and MAX marks. Close the compensating tank
and mount both spoilers.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
64
Changing the basic position of the clutch lever
The basic position of the clutch lever can be modified by turning the adjusting screw [1].
This lets you adjust the best clutch lever position for any hand size.
To adjust, pull the clutch lever towards the front. Turning the adjusting screw in a clockwise
direction will move the clutch lever away from the driver. Turning the adjusting screw in a
counterclockwise direction will move the clutch lever towards the driver.
1
Adjustment of the clutch lever position is only possible within certain limits. Only turn the
adjusting screw manually and never apply excessive force.
Checking the oil level of the hydraulic clutch
The oil level should be between the „MIN“ and „MAX“ marks with the master cylinder in a
horizontal position.
If necessary, add SAE 10 biodegradable hydraulic oil (Motorex clutch fluid 75), available
from your authorized KTM workshop.
KTM uses biodegradable, hydraulic mineral oil to actuate the hydraulic clutch. Do not mix
this oil with any other hydraulic oil. Always useoriginal KTM hydraulic oil (available from
your authorized KTM workshop) to make sure your clutch operates smoothly.
Never refill with brake fluid.
Adjusting the handlebar tilt
Loosen the screws [2]. Adjust the handlebar and tighten the screws to 20 Nm.
Make sure the handlebar instruments do not touch the fuel tank when the handlebar is com-
pletely turned.
2
Tilting the handlebar too far back will reduce the steering angle since the handlebar instru-
ments will touch the fuel tank
If the handlebar is tilted too far back, the handlebar instruments may damage the fuel tank.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
65
How to change the handlebar position (Super Duke R)
The upper triple clamp includes 2 bores arranged at a distance of 15 mm (0.6 in) from one
another. Accordingly, you can mount the handlebar in 2 different positions.
The steering angle is reduced if the handlebar is mounted in the rear position.
Adjust the steering lock so it does not hit the fuel tank.
Adjusting the steering damper (Super Duke R)
The steering damper stabilizes the steering whenever the front wheel is relieved or off the
ground. The damping degree can be adjusted to harder (+) or softer (-) damping by turning
the adjusting knob [1].
BASIC SETTING
1
– Turn the adjusting knob all the way to the stop in a clockwise direction
– Turn 20 clicks in a counterclockwise direction
Only change the setting by 3 clicks at a time and take a test ride.
– Always check the steering for smooth operation before starting off on a ride.
– Do not try to adjust the steering damper while driving. Your attention will be distracted
from the traffic and this may cause you to lose control of your motorcycle.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
66
Engine oil
Automobile engine oil used to be used for four-stroke motorcycles before there were sepa-
rate motorcycle specifications. Different technical developments made it necessary to have
a separate specification for four-stroke motorcycles - the JASO T903 MA standard. Whereas
car engines require long changing intervals, motorcycle engines require a higher power out-
put at higher speeds. Most motorcycle engines also use the same oil to lubricate the trans-
mission and the clutch. The JASO MA standard responds to these special requirements.
Only use fully synthetic engine oils that meet the JASO MA quality requirements (see infor-
mation on the can).
JASO T903 MA
TEMPERATUR
0°C
32°F
5W/40
10W/50
KTM recommends Motorex Power Synt 4T in the 10W/50 viscosity (for temperatures over
0°C, 32°F) or 5W/40 (for temperatures under 0°C, 32°F).
Checking the engine oil level
Check the engine oil level when the engine is warm (at least 4 bars on the temperature indi-
cator light up). Allow the warm engine to run idle for approx. 1 minute and place the motor-
cycle on a level surface (not on the side stand).
Wait 20 seconds to allow the oil level in the inspection glass to adjust to the oil level in
the oil tank. The oil level should be between the MIN and MAX marks, add engine oil if
necessary.
Always check the oil level when the engine is warm. A cold engine can distort the measur-
ing results. Engine oil expands when heated, increasing the oil level.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
67
Refilling engine oil
To refill engine oil, take off the right spoiler [1] by removing the screws [2].
1
2
2
Also remove the screws [3] and take off the spoiler.
3
3
Unscrew the plug [4] and refill engine oil. Wait 20 seconds and check the oil level again.
The quantity of oil between the MIN and MAX marks is 0.3 liter. Mount the plug and check
the engine for leaks.
Finally, mount the spoilers.
4
– Insufficient amounts of or low-grade engine oil lead to premature wear in the engine.
– Do not overfill the engine case.
– Do not underfill the engine case.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
68
Changing the engine oil and the oil filter, cleaning the oil screen
You may only change the engine oil yourself after the warranty period has expired. The war-
ranty will become void if you change the oil yourself during the warranty period.
NOTE: The LC8 engine has a dry-sump lubrication system. The engine oil is pumped from
the oil sump in the engine case to the oil tank. The engine oil must also be drained from
the oil tank during an oil change. Since many parts must be demounted for an oil change,
we recommend having the engine oil changed by an authorized KTM workshop.
During the guaranty period, the oil change must be performed by an authorized KTM
mechanic. Otherwise, the guarantee will become void.
1
2
The engine oil change is to be carried out when the engine is still warm.
An engine having been run warm, and the engine oil in it is very hot – do not burn yourself.
3
Park the motorcycle on an even surface in an upright position. Place a vessel under the
engine to catch the used oil and remove the oil drain plug [1]. Remove the oil drain plug
[1], take off the cap [2] and pull the oil sieve out of the engine case with a pair of pliers.
Remove the oil filter cover [3] and pull the oil filter out of the engine case with circlip pli-
ers (upside-down).
Remove the screws [4], loosen the screws [5] by 2 turns and remove the front spoiler towards
the front.
4
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
69
Remove the drain plug [6] on the oil tank and allow the oil to drain into a receptacle. Remove
the screws [7] and tilt the oil return valve [8] to the side.
8
7
6
7
Carefully pull the oil screen [9] out of the oil tank.
9
Thoroughly clean the drain plugs, the cover and both oil screens. Clean all rubber seal rings
and check for damage. Replace if necessary.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
70
Mount the oil drain plug on the engine with a new seal ring and tighten to 20 Nm.
Slide the oil screen [1] into the guides in the oil pump housing with the TOP mark fac-
ing up. Make sure the form ring is in place and mount the cap [2]. Tighten the screws to
10 Nm.
2
1
Insert a new oil filter [3] in the engine case, grease the O-ring and mount the oil filter cover
together with the O-ring. Tighten the screws to 6 Nm.
3
Only use original ktm oil filters. The engine can be damaged if other filters are used.
Mount the oil drain plug on the oil tank with a new seal ring and tighten to 20 Nm.
Grease the seal ring [4] and carefully slide the oil screen into the oil tank. Position the oil
return valve [5], mount the screws and tighten to 10 Nm.
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE WORK ON CHASSIS AND ENGINE »
71
Remove the right spoiler (see Refilling the engine oil) and unscrew the plug [6]. Add 2.5
liters (0.7 USgal) of fully synthetic engine oil meeting the JASO MA standard (e.g. Motorex
Power Synt 4T) and remount the plug. Start the engine and allow to run warm in neutral
until 4 bars on the temperature indicator light up. Switch off the engine and check the oil
level (see Checking the engine oil level).
6
Check the engine and the oil tank for oil leakage.
Fit the slots in the front spoiler on the lower screws [7] and tighten. Apply Loctite 243 to
the side screws [8] and tighten to 10 Nm.
Finally, mount the spoiler (see Refilling the engine oil).
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING »
72
If you have your motorcycle serviced as set forth in this manual, no malfunctioning is to be expected. Nevertheless, if an error does arise,
we recommend that you look for the error according to the following chart.
Please note that you cannot perform all of the work yourself. If you are not sure, contact your KTM dealer.
TROUBLE
CAUSE
REMEDY
Engine does not start when the Operating error
starter button is actuated
Turn on the ignition, switch the gear to neutral and switch the
emergency OFF switch on, do not accelerate while starting the
engine.
Discharged battery
Recharge the battery and investigate the causes for discharg-
ing; contact an authorized KTM workshop.
Blown fuse
Replace fuse 1
Main fuse is blown
Remove the front spoiler and replace the main fuse
Defect ignition lock or emergency
OFF switch
Check ignition lock and emergency OFF switch, contact an
authorized KTM workshop.
Defect safe-starting system.
A gear is engaged
Contact an authorized KTM workshop.
Shift the transmission to neutral.
The engine cranks only with
pulled clutch lever
A gear is engaged and the side
stand is still folded down
Shift the transmission to neutral.
Defect safe-starting system.
Defect safe-starting system.
Contact an authorized KTM workshop.
Contact an authorized KTM workshop.
Engine cranks with gear
engaged.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING »
73
TROUBLE
CAUSE
REMEDY
Engine cranks but doesn’t start. Operating error
Pay attention to starting off information
(see driving instructions).
Blown fuse for the fuel pump
Replace fuse 4
Clutch not attached to the fuel line Connect the clutch to the fuel line
The plug and socket connector on
the wiring harness is oxidized
Remove the panel and fuel tank, clean the plug and socket
connector and spray with contact spray
Visit an authorized KTM workshop
Switch to neutral gear
Error in the injection system
A gear is engaged and the side
stand is folded down
Engine will not reach full power Air filter/fuel filter heavily soiled
Error in the injection system
Have the air filter/fuel filter replaced at an authorized KTM
workshop
Visit an authorized KTM workshop
Engine overheats
Insufficient cooling liquid
Refill cooling liquid (see maintenace work), check cooling sys-
tem for leaks
Radiator fins are extremely dirty
Foam forms in cooling system
Clean radiator with water jet
Replace cooling liquid, use antifreezer with brand name
Run the radiator hose correctly or replace
Radiator hose is kinked or
damaged
Thermostat defective
Have the thermostat checked (opening temperature 75°C,
167°F) or replaced; contact an authorized KTM workshop
Download from Www.Somanuals.com. All Manuals Search And Download.
74
TROUBLESHOOTING »
TROUBLE
CAUSE
REMEDY
Engine overheats
Blown fan fuse
Replace fuse 5
Defect fan or thermoswitch for fan
Contact an authorized KTM workshop.
Air in the cooling system
Bleed the cooling system (see Maintenance work)
Visit an authorized KTM workshop
FI lamp is blinking / lights up
Engine stalls while driving
Error in the injection system
No fuel
Refuel
Fuse for fuel pump has blown
Replace fuse 4
High oil consumption
Engine oil level too high
Check engine oil level when the engine is warm; correct if
necessary
Engine oil too thin (viscosity)
Use thicker engine oil; see chapter „Engine oil“
Headlight and position light fail Blown fuse
Replace fuse 2
Replace fuse 3
Flasher lights, brake light, horn Sicherung durchgeschmolzen
and combined instrument fail
Time is not displayed or not cor- Blown fuse, thus no continuous
Replace fuse 6 and set the clock.
rectly displayed
power supply
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING »
75
TROUBLE
CAUSE
REMEDY
The battery is discharged
The ignition (power consumer) has- Recharge the battery according to the relevant instructions.
n’t been switched off
The battery isn’t charged by the
generator
Voltage regulator and generator should be checked by an
authorized KTM workshop.
No values are visible in the com- Blown fuse
bined instrument display.
Replace fuse 3
The speed indication on the
combined instrument is not
working
Pickup cable is damaged or con-
tacts on the cable connector have
oxidized
Check the pickup cable for damage, visit an authorized KTM
workshop
The blink code indicates which component is affected by an error. This allows the error to be identified if no diagnosis tool is available.
BLINK CODE
SIGNAL / COMPONENT
ERROR DESCRIPTION
ENGINE
02
06
07
09
11
Pulse generator
Malfunction
Stalls
Throttle sensor
Output signal too low /high
Output signal too low /high
Output signal too low /high
Output signal too low /high
Continues to run
Continues to run
Continues to run
Continues to run
Sensor for 2nd throttle valve
Intake manifold air pressure for sensor rear cylinder
Intake manifold air pressure sensor for front cylinder
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING »
76
The blink code indicates which component is affected by an error.
This allows the error to be identified if no diagnosis tool is available.
BLINK CODE
12
SIGNAL / COMPONENT
ERROR DESCRIPTION
Output signal too low /high
Output signal too low /high
Output signal too low /high
Output signal too low /high
Malfunction
ENGINE
Coolant temperature sensor
Air temperature sensor
Continues to run
Continues to run
Continues to run
Continues to run
Continues to run
Continues to run
Continues to run
Continues to run
Stalls
13
14
Ambient air pressure sensor
Tilt angle sensor
15
17
Lambda probe for rear cylinder
Lambda probe for front cylinder
Control unit voltage supply
Side stand switch
18
Malfunction
24
Malfunction
25
Short circuit to ground
Malfunction
33
Injection nozzle for rear cylinder
Injection nozzle for front cylinder
Ignition coil for rear cylinder
Injection coil for front
34
Malfunction
Stalls
37
Malfunction
Stalls
38
Malfunction
Stalls
41
Fuel pump relay
Short circuit to ground / positive
Short circuit to ground / positive
Short circuit to ground / positive
Malfunction
Stalls
45
Lambda probe heater for rear cylinder
Lambda probe heater for front cylinder
Idle control motor
Continues to run
Continues to run
Continues to run
Continues to run
46
49
53
Purge valve for carbon canister
Secondary air valve
Short circuit to ground / positive
54
Short circuit to ground / positive or interruption Continues to run
65
EEPROM error
Malfunction
Malfunction
Malfunction
Malfunction
Continues to run
Continues to run
Continues to run
Continues to run
68
Vacuum hose for front cylinder is defective
Vacuum hose for rear cylinder is defective
Stepper motor for 2nd throttle valve
69
72
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING »
77
Regular cleaning and paintwork care are part of the maintenance work and help to maintain the value of your motorcycle.
Never clean the motorcycle with a power washer or a strong water jet, otherwise the pressure will allow water to enter the electric compo-
nents, plugs, cables, bearings, etc. which can cause malfunctioning or can lead to premature wear of these components.
– Before you wash your motorcycle, close the muffler openings.
– Use warm water with a commercial detergent and sponge. Coarse dirt can be removed with a soft water jet. Areas that are heavily soiled
can be sprayed with a motorcycle cleaner (e.g. Motorex 900) and cleaned with a brush.
– After the motorcycle has been rinsed with a soft water jet, it should be dried by air pressure and a cloth. Then take a short drive until
the engine has reached the working temperature and also use the brakes. Due to the heat, the water also evaporates at the unapproach-
able parts of the engine and the brakes.
– After the motorcycle has cooled down, oil or lubricate all of the friction bearings and bearing positions and treat the chain with chain
spray. Treat all bare areas (except brake disks) with a corrosion inhibitor (e.g. Motorex Protect & Shine).
– The exhaust pipes and mufflers are made of stainless steel and should be treated with a suitable care product.
– To prevent failures in the electric system, you should treat the ignition lock, the emergency OFF switch, light switch and the socket con-
nectors with contact spray.
– Treat all of the painted parts with a mild paint care product (e.g. Motorex Moto Polish).
CONSERVATION FOR WINTER OPERATION »
In the event that the motorcycle is also used in winter and on roads where one has to expect salt spraying, you will have to take
precautions against the aggressive road salt.
– clean motorcycle thoroughly and let it dry
– treat engine, swing arm, and all other bare parts (except for brake discs) with a wax-based anti-corrosion agent.
Keep anti-corrosion agent from getting into contact with the brake discs, for otherwise this will significantly reduce the braking power.
After rides on salted roads, clean motorcycle thoroughly with cold water and let it dry well!
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE »
78
If you plan to immobilize your motorcycle for a longer period of time, proceed as follows:
– Run the tank empty to be able to add fresh fuel when starting up again.
– Clean the motorcycle thoroughly (see CLEANING chapter).
– Change the engine oil and the oil filter (old engine oil contains aggressive impurities).
– Check the quantity of antifreeze and cooling liquid.
– Remove and charge the battery (see Charging the battery chapter).
– If possible, jack up the motorcycle to lift the wheels off the ground.
– The storage site should be dry and not subject to larger temperature fluctuations.
– Cover the motorcycle with a permeable cover or blanket. Do not use impermeable material since it will not allow and moisture to escape
and will cause corrosion.
Do not briefly run the engine of an immobilized motorcycle since the engine will not become warm enough and any vapor produced during
the combustion process will condense and cause the valves and exhaust to rust.
STARTING UP AFTER IMMOBILIZATION
– Mount the charged battery (pay attention to the polarity) and set the clock.
– Fill fresh fuel in the tank.
– Inspect the motorcycle as you would before each start-up (see „Driving Instructions“).
– Go on a short, cautious test ride
NOTE: before you store your motorcycle at the end of the season, check all parts for proper functioning and wear. If service, repairs or con-
versions are necessary, have them carried out while the motorcycle is immobilized (workshops are not fully utilized). This will help to avoid
long waiting periods at the beginning of the season.
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – CHASSIS »
79
CHASSIS
990 SUPER DUKE / R 2007
Frame
Tubular chrome-molybdenum-steel space frame
WP Suspension – Up Side Down 4860 ROMA
135 mm (5.3 in)
Fork
Spring travel front
Rear suspension
Spring travel rear
Front brake
WP Suspension 4618 BAVP
Super Duke: 160 mm (6.3 in)
Super Duke R: 150 mm (5.9 in)
Disk brake, 2 perforated brake disks Ø 320 mm (12.6 in), brake calipers radially bolted
Disk brake, perforated brake disk Ø 240 mm (9.4 in), floating brake caliper
DUNLOP Sportmax D208 RR 120/70 ZR17 M/C 58W
Rear brake
Authorized front tires *
Air pressure front
Road, driver only...............................................2.4 bar
Road, with passenger / maximum payload ...........2.4 bar
Authorized rear tires *
Air pressure rear
DUNLOP Sportmax D208 RR 180/55 ZR17 M/C 73W
Road, driver only...............................................2.4 bar
Road, with passenger / maximum payload ...........2.6 bar
Fuel tank capacity
Gear ratio – rear wheel
Chain
18.5 liters (4.9 USgal), 3.5 (0.9 USgal) liters Reserve
17:38
5/8 x 5/16” X-ring
high beam ............................................H3 12V 55W (socket PK22s)
low beam ..............................................H7 12V 55W (socket PX26d)
USA: high beam + low beam ..................H4 12V 60/55 W (socket P43t)
position light front..................................12V 5W (socket W2,1x9,5d)
indicator lamps .....................................LED
Lighting
position light rear ...................................12V WR5W (socket W2,1x9,5d) ......Super Duke R: LED
USA: position light rear...........................12V 5W (socket W2,1x9,5d) ..........Super Duke R: LED
stoplight ...............................................12V PR21W (socket BAW15s) ........Super Duke R: LED
USA: stoplight .......................................12V 21W (socket BA15s) ..............Super Duke R: LED
flashers .................................................12V RY10W (socket BAU15s)
licens plate illumination .........................12V 5W (socket W2,1x9,5d)
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – CHASSIS »
80
CHASSIS
990 SUPER DUKE / R 2007
maintenance-free battery 12V 11.2 Ah
Super Duke: 66.1°
Battery
Steering head angle
Wheel base
Super Duke R: 67.3°
1450 ± 10 mm (57 ± 0.4 in)
Super Duke: 850 mm (33.5 in)
Super Duke: 140 mm (5.5 in)
186 kg (410.6 lbs)
Seat height, unloaded
Ground clearance, unloaded
Dry weight
Super Duke R: 860 mm (33.9 in)
Super Duke R: 150 mm (5.9 in)
Max. axle load front
Max. axle load rear
Max. total load
180 kg (397.3 lbs)
250 kg (551.8 lbs)
387 kg (854.2 lbs)
Super Duke Super Duke R
Super Duke Super Duke R
BASIC SETTING
SHOCK ABSORBER WP 4618 BAVP
BASIC SETTING
FORK WP 4860 ROMA
Compression adj. Low Speed (clicks) 25 20 10 10 20 16 10 16
Compression adjuster (clicks)
Rebound adjuster (clicks)
Spring preload (turns)
Spring
20 15 10 10 18 18 14 18
Compression adj. High Speed (turns)
Rebound adjuster (clicks)
Spring preload (mm)
Spring
2 1.5
1
1 2.5 1.5 1 1.5
20 15 10 10 16 16 12 16
20 12 8 8 12 12 8 12
5
5
5
5
5
5
5
5
6
6
6
6
5
5
5
5
9.5 N/mm
9.5 N/mm
170/185
180/185
Air chamber length
Fork oil
110 mm (4.3 in)
SAE 5 (WP 4860.0401)
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – CHASSIS »
81
TIGHTENING TORQUES – CHASSIS 2007
Collar bolt on front wheel spindle
Collar nut wheel spindle rear
M24x1.5
60 Nm
M25x1.5
M14x1.5
M19x1.5
M8
90 Nm
80 Nm
AH bolt shock absorber top/bottom
Collar nut for swing arm bolt
130 Nm
AH bolts on subframe
Loctite 243 + 25 Nm
Loctite 243 + 25 Nm
45 Nm
AH bolts on back of footrest support
Engine carrier bolts
M8
M10
M8
HH clamp bolts on top triple clamp
HH clamp bolts on bottom triple clamp
HH screw for steering head
12 Nm
M8
15 Nm
M20x1.5
M8
12 Nm
HH clamp bolts on fork leg axle passages
Collar bolts for handlebar clamps
AH bolt for handlebar mount
15 Nm
M8
20 Nm
M10
M8
20 Nm
HH clamp bolts for steering stem
Collar bolt front/rear brake disk
HH bolts on front brake caliper
20 Nm
M8x1.25
M10x1.25
M6
Loctite 243 + 30 Nm
Loctite 243 + 45 Nm
10 Nm
HH bolts on handbrake cylinder
HH bolts on footbrake cylinder
M6
Loctite 243 + 10 Nm
Loctite 243 + 25 Nm
Loctite 243 + 10 Nm
Loctite 243 + 25 Nm
Loctite 243 + 18 Nm
Loctite 243 + 12 Nm
Loctite 243 + 6 Nm
Loctite 243 + 45 Nm
AH bearing bolt for foot brake pedal, shift lever
HH screw on cover plate for foot brake lever/shift mechanism
Relay for shift shaft (on connecting support)
Relay for shift shaft (on shift shaft)
Gearshift rod attachment
M8
M6
M8
M6
M6
HH bolts on foot brake pedal surface
AH bolts for side stand bracket - engine
M5
M10
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – CHASSIS »
82
TIGHTENING TORQUES – CHASSIS 2007
HH bolts for side stand fixture - side stand bracket
HH bolts for side stand mounting
HH bolt for spring rest on side stand
HH bolt for side stand switch
Drain plug on oil tank
M10
M10
M8
Loctite 243 + 25 Nm
Loctite 243 + 35 Nm
Loctite 243 + 25 Nm
M4
Loctite 243 + 2 Nm
M12x1.5
M8
25 Nm
Exhaust nuts on manifold
Exhaust clamps
evenly, do not bend sheet metal
M8
8 Nm
Exhaust clamps for ball joint
AH bolts on tank cover
M8
35 Nm
M5
5 Nm
HH bolts on tank mounting
Collar screws for in-tank pump
AH screw on arm for tank support
Collar screw for gas pressure shock absorber
Seat fixing plate
M6
6 Nm
M6
6 Nm
M10
M6
15 Nm
6 Nm
M5
4 Nm
8 Nm
HH nut for seat lock
M19x1
M10x1.25
M5
Jerk damper bolt - rear wheel
Chainguard
Loctite 243 + 50 Nm
5 Nm
Chain sliding guard
M5
5 Nm
Front spoiler
M6
Loctite 243 + 10 Nm
8 Nm
Taillight
M6
Other bolts on chassis
M6
10 Nm
25 Nm
45 Nm
M8
M10
Other collar nuts on chassis
M6
15 Nm
30 Nm
50 Nm
M8
M10
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – ENGINE »
83
ENGINE
990 LC8 2007
Design
Liquid-cooled, 2-cylinder 4-stroke engine with 75° V arrangement with balancer shaft and electric starter
Displacement
Bore / Stroke
Compression ratio
Fuel
999 cc
101/62.4 mm
11.5:1
unleaded fuel with at least RON 95 (USA: Premium RON 91) *
4 valves controlled over bucket tappet and 2 camshafts, camshaft drive with gears/chain
Intake: 38 mm Exhaust: 33 mm
Valve timing
Valve diameter
Valve clearance, cold
Crankcase bearing
Conrod bearing
Piston pin bearing
Piston
Intake: 0.10 - 0.15 mm Exhaust: 0.25 - 0.30 mm
Friction bearings (2 main bearings / 1 supporting bearing)
Friction bearing
Dual-fuel bearing
Light alloy – forged
Piston rings
Engine lubrication
Engine oil
1 compression ring, 1 taper face ring, 1 single-piece oil scraper ring with spiral-type expander
Dry sump with 2 trochoidal pumps (pressure pump and suction pump)
SAE 10W-50 (Motorex Power Synt 4T) #
approx. 3 liters (0.8 USgal) during oil/filter change
Straight-toothed spur wheels 35 : 67
Quantity of engine oil
Primary drive
Clutch
Multi-disc clutch in oil bath
Transmission
Gear ratio
6-speed claw shifted
1st gear 14:36
2nd gear 16:30
3rd gear 20:30
4th gear 21:27
5th gear 23:26
6th gear 25:26
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS – ENGINE »
84
ENGINE
990 LC8 2007
Ignition system
Ignition timing
Map-controlled via TPS
Spark plug
breakerless transistorized electronic ignition system with digital ignition advance
Map-controlled via TPS
12V 450W at 6000 rpm
NGK IR KR8BI
Electrode distance
Cooling system
Cooling liquid
Starting aid
0.8 mm
liquid cooled, permanent circulation of cooling liquid through water pump
2.1 liters (0.55 USgal), 50% antifreeze, 50% distilled water, at least –25° C
electric starter
PON / CLC
87
RON / ROZ
91
MON
83
#
*
JASO T903 MA
91 Premium
95
87
PON = Pump Octane Number
CLC = Cost of Living Council
RON = Research Octane Number
ROZ = Research Oktan Zahl
MON = Motor Octane Number
TEMPERATUR
0°C
32°F
5W/40
10W/50
Engine oil
Only use fully synthetic engine oils that meet the JASO
MA quality requirements (see information on the can).
KTM recommends Motorex Power Synt 4T in the 10W/50
viscosity (for temperatures over 0°C, 32°F) or 5W/40
(for temperatures under 0°C, 32°F).
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAD WORD INDEX »
85
Accessories and payload . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Adjusting compression damping of fork . . . . . . . . . . . . . . . . .37
Adjusting rebound damping of fork . . . . . . . . . . . . . . . . . . . .37
Adjusting the basic position of the hand brake lever . . . . . . . .44
Adjusting the fork and shock absorber . . . . . . . . . . . . . . . . .37
Adjusting the handlebar tilt . . . . . . . . . . . . . . . . . . . . . . . . .64
Adjusting the headlight range . . . . . . . . . . . . . . . . . . . . . . . .58
Adjusting the spring preload on the fork . . . . . . . . . . . . . . . . .38
Adjusting the steering damper (Super Duke R) . . . . . . . . . . .65
Baggage loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Bleeding the cooling system . . . . . . . . . . . . . . . . . . . . . . . .62
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Chain maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Changing the basic position of the clutch lever . . . . . . . . . . .64
Changing the engine oil and the oil filter,
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Clutch lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Combination switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Combined instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Combined instrument display . . . . . . . . . . . . . . . . . . . . . . . . .8
Compression damping of fork . . . . . . . . . . . . . . . . . . . . . . . .19
Compression damping of shock absorber . . . . . . . . . . . . . . . .38
Conservation for winter operation . . . . . . . . . . . . . . . . . . . . .77
Consumer information for USA only . . . . . . . . . . . . . . . . . . . .87
Cooling liquid temperature display . . . . . . . . . . . . . . . . . . . .12
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Correcting the chain tension . . . . . . . . . . . . . . . . . . . . . . . .40
Damping action during compression of shock absorber . . . . . .20
Dismounting and mounting the rear wheel . . . . . . . . . . . . . . .50
Dismounting and remounting the front wheel . . . . . . . . . . . .48
Driving instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Engine number, engine type . . . . . . . . . . . . . . . . . . . . . . . . . .6
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Foot brake pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Footrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Function buttons on combined instrument . . . . . . . . . . . . . . .8
Fuses for individual power consumers . . . . . . . . . . . . . . . . . .56
General information on KTM disk brakes . . . . . . . . . . . . . . . .42
General tips and warnings for starting the motorcycle . . . . . . .22
Hand brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Helmet lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Holding strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
cleaning the oil screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Chassis number, Type label . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Check the following before each start . . . . . . . . . . . . . . . . . .24
Checking the chain for wear . . . . . . . . . . . . . . . . . . . . . . . . .41
Checking the chain tension . . . . . . . . . . . . . . . . . . . . . . . . . .40
Checking the cooling liquid level in the compensating tank . . .61
Checking the cooling liquid level in the radiator . . . . . . . . . . .62
Checking the engine oil level . . . . . . . . . . . . . . . . . . . . . . . .66
Checking the front brake fluid level . . . . . . . . . . . . . . . . . . .44
Checking the front brake pads . . . . . . . . . . . . . . . . . . . . . . . .45
Checking the oil level of the hydraulic clutch . . . . . . . . . . . . .64
Checking the rear brake fluid level . . . . . . . . . . . . . . . . . . . .46
Checking the rear brake pads . . . . . . . . . . . . . . . . . . . . . . . .46
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAD WORD INDEX »
86
How to change the handlebar position (Super Duke R) . . . . . .65
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Instructions for initial operation . . . . . . . . . . . . . . . . . . . . . .22
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Jump start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Maintenance work on chassis and engine . . . . . . . . . . . . . . . .36
Operation instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Periodic maintenance schedule . . . . . . . . . . . . . . . . . . . . . . .32
Rebound damping of fork . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Rebound damping of shock absorber . . . . . . . . . . . . . . . . . . .39
Rebound damping of shock absorber . . . . . . . . . . . . . . . . . . .21
Refilling engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Removing and remounting the battery . . . . . . . . . . . . . . . . .53
Replacing the brake light and taillight bulbs . . . . . . . . . . . . .59
Replacing the flasher bulbs . . . . . . . . . . . . . . . . . . . . . . . . .59
Replacing the headlight lamp . . . . . . . . . . . . . . . . . . . . . . .57
Running in the LC8 engine . . . . . . . . . . . . . . . . . . . . . . . . . .22
Seat lock, removing the seat . . . . . . . . . . . . . . . . . . . . . . . .16
Serial number locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Shift lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Shifting/Riding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Side stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Spring preload of the fork . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Starter tip switch, Emergency OFF tip switch . . . . . . . . . . . . .15
Starting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Starting up after immobilization . . . . . . . . . . . . . . . . . . . . . .78
Stopping and parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Technical specifications – chassis . . . . . . . . . . . . . . . . . . . . .79
Technical specifications – engine . . . . . . . . . . . . . . . . . . . . .83
Tires, air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Tool set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION FOR USA ONLY »
87
REPORTING SAFETY DEFECTS
If you believe that your vehicle has a defect which could cause an accident resulting in injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying KTM North America, Inc.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remady cam-
paign. However, NHTSA cannot become involved in individual problems between you, your dealer, or KTM North America, Inc.
Transportation, 400 7th Street, Southwest, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.
NOISE EMISSION WARRANTY
KTM Sportmotorcycle AG warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise standards. This warranty extends to the first per-
son who buys this exhaust system for purposes other than resale, and to all subsequent buyers.
Warranty claims should be directed to:
KTM North America, Inc. 1119 Milan Avenue, Amherst, Ohio 44001, Telephone: (440) 9853553
TAMPERING WARNING
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED. FEDERAL LAW PROHIBITS THE FOLLOWING ACTS OR CAUSING THEREOF:
1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into
any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or
2) The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW.
1) Removal of, or puncturing the muffler, baffles, header pipes or any other components which conducts exhaust gases.
2) Removal or puncturing of any part of the intake system.
3) Lack of proper maintenance.
4) Replacing any moving part of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the manufacturer.
WARNING STATEMENT
This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penal-
ties under state and local ordinances.
CONSUMER RIGHTS
Limited Warranty claims should be directed to an authorized KTM dealer. If you are not satisfied, please contact KTM North America, Inc., Customer Relations, 1119 Milan
Avenue, Amherst, Ohio 44001.
Your rights may vary, please refer to the applicable state laws.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION FOR USA ONLY »
88
Sticker positions:
1
2
3
4
5
6
7
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION FOR USA ONLY »
89
[1] EAVP
[2] Type label CAN
[3] Suspension setting
[6] Noise emission
[9] Type label USA
[4] Chain tension
[5] Technical information
[7] Vehicle emission
[8] Before you go for the first ride
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THIS SPACE FOR NOTES »
90
Download from Www.Somanuals.com. All Manuals Search And Download.
11/2006
FOTO: MITTERBAUER
KTM Group Partner
KTM Sportmotorcycle AG
A–5230 Mattighofen
Download from Www.Somanuals.com. All Manuals Search And Download.
|