DVD-RECEIVER
KDV-415U
KDV-MP5042U
INSTRUCTION MANUAL
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new DVD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KDV-415U/ KDV-MP5042U Serial number
US Residence Only
Register Online
Register your Kenwood product at
© B64-4427-00/00 (KW/RW)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• The characters which can be displayed by this unit
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
How to reset your unit
• If this unit or the connected unit (disc auto changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
Handling discs
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use disc type accessories.
Reset button
• Clean from the center of the disc and move
outward.
• When removing discs from this unit, pull them out
horizontally.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
• If the disc center hole or outside rim has burrs,
use the disc only after removing the burrs with a
ballpoint pen etc.
¤
Discs that cannot be used
• Discs that are not round cannot be used.
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• Discs with coloring on the recording surface or discs
that are dirty cannot be used.
Lens Fogging
• This unit can only play the CDs with
.
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
DVD player of the unit. Called lens fogging, this
condensation on the lens may not allow discs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a disc that has not been finalized.
(For the finalization process refer to your writing
software, and your recorder instruction manual.)
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
List of playable discs
About Audio files
•
Playable Audio file
Disc
types
DVD
Standard
Support
Remark
MP3 (.mp3), WMA (.wma), Linear PCM (WAV) (.wav)
‡
×
‡
DVD Video
DVD Audio
DVD-R
DTS not supported.
⁄
•
If music of normal CD and other playback systems are
MP3/WMA/WAV/JPEG/
MPEG/DivX Playback
Multi-border/Multisession/
(Playback depends on
authoring conditions)
Video mode supported
VR mode supported (Only
DVD-R/RW)
recorded in the same disc, only the playback system
recorded at the first setout is played.
Acceptable media
‡
‡
‡
DVD-RW
DVD+R
•
CD-R/RW/ROM, DVD R/RW, mass-storage-class USB
device, iPod with KCA-iP240V/ KCA-iP101
DVD+RW
•
•
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo.
Playable USB device file system
FAT32, FAT16
‡
‡
×
DVD-R DL (Dual layer)
DVD+R DL (Double layer)
DVD-RAM
Only video format
‡
CD
Music CD
CD-TEXT
Although the audio files are complied with the standards
listed above, the play maybe impossible depending on
the types or conditions of media or device.
‡
CD-ROM
MP3/WMA/WAV/JPEG/
DivX playback
Multisession supported
Packet write not supported.
‡
‡
×
‡
×
CD-R
•
Playing order of the Audio file
CD-RW
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
DTS-CD
Video CD (VCD)
Super video CD
Photo CD
(ꢁ):Root
ꢁ
×
%
<
v
: F
Folder
vꢀ
<
vꢀ
CD-EXTRA
Only music CD session can
be played.
Sound quality of normal
CD music
:
Audio file
ꢂ
vꢅ
vꢆ
ꢂ
%
HDCD
vꢅ
vꢆ
CCCD
×
×
%
ꢄ
ꢄ
ꢇ
vꢃ
ꢇ
vꢃ
vꢈ
v.
Others
DualDisc
Super audio CD
Only CD layer can be
played.
vꢈ
v.
‡ : Playback is possible.
% : Playback is partly possible.
× : Playback is impossible.
An online manual about audio files is put on the
manual, detailed information and notes which are
not written in this manual are provided. Make sure
to read through the online manual as well.
⁄
•
When buying DRM enabled contents, check the
Registration Code in the <DivX registration> (page 13).
Registration Code changes each time a file with the
displayed Registration Code is played to protect against
copying.
About Video files
•
•
•
Acceptable video files
MPEG1, MPEG2, DivX
Extensions
mpg, mpeg, divx, div, avi
Acceptable media
Use of “DualDisc”
When playing a “DualDisc” on this unit, the surface of
the disc that is not played may be scratched while the
disc is inserted or ejected. Since the music CD surface
does not conform to the CD standard, playback may
be impossible.
CD-R/RW/ROM, DVD R/RW, mass-storage-class USB
device, iPod with KCA-iP240V
Acceptable discs, disc formats, USB device file system,
file and folder names and playing order are the same
as those for audio files. See <About Audio files>.
(A “DualDisc” is a disc with one surface containing
DVD standard signals and the other surface
containing music CD signals.)
|
4
KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
About Picture files
About USB device
• In this manual, the word “USB device” is used for
flash memories and digital audio players which have
USB terminals.
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
•
•
•
Acceptable picture files
JPEG
Extensions
jpg, jpeg
Acceptable media
CD-R/RW/ROM, DVD R/RW, mass-storage-class USB
device
Acceptable discs, disc formats, USB device file system,
file and folder names and playing order are the same
as those for audio files. See <About Audio files>.
iPod/iPhone that can be connected to this
unit
Made for
We shall have no compensation for any damage
arising out of erasure of the stored data.
• iPod nano (1st generation)
• iPod nano (3rd generation)
• iPod with video
• iPod touch (1st generation) • iPod touch (2nd generation)
Works with
• iPod nano (2nd generation)
• iPod nano (4th generation)
• iPod classic
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
• iPhone
• iPhone 3G
About DivX
• Update iPod/iPhone software to the latest version.
DivX is a popular media technology created by DivX,
Inc. DivX media Files contain highly compressed video
with high visual quality that maintains a relatively
small file size. DivX files can also include advanced
media features like menus, subtitles, and alternate
audio tracks. Many DivX media files are available for
download online, and you can create your own using
your personal content and easy-to-use tools from
DivX.com.
• You can control an iPod/iPhone from this unit by
connecting an iPod/iPhone (commercial product)
with Dock connector using an optional accessory
iPod connection cable (KCA-iP240V/ KCA-iP101). The
word “iPod” appearing in this manual indicates the
iPod/iPhone connected with the KCA-iP240V/ KCA-
iP101 (optional accessory).
• By connecting your iPod/iPhone to this unit with
an optional accessory iPod connection cable (KCA-
iP240V/ KCA-iP101), you can supply power to your
iPod/iPhone as well as charge it while playing music.
However, the power of this unit must be on.
About DivX Certified
DivX Certified products are officially tested by the
creators of DivX and guaranteed to play of DivX video,
without DivX 6.
⁄
Certified products qualify for one of several DivX
Profiles that designate the type of video the product
supports, from compact portable video to high-
definition video.
• If you start playback after connecting the iPod, the
music that has been played by the iPod is played
first.
• You cannot operate iPod if “KENWOOD” or “✓” is
displayed on the iPod.
• A video file stops playing if you switch to another
source while playing it. You cannot play from the
last playback position if you switch back to iPod.
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the
following map.
1
5
2
1
2
1
4
5
2
4
DVD disc marks
Operation regulatory marks
With this DVD, some functions of this unit such as the
play function may be restricted depending on the
location where the DVD is playing. In this case, the
following marks will appear on the screen. For more
information, refer to the disc manual.
Symbol
Description
Indicates a region number. The discs with this mark can
be played with any DVD player.
ALL
Indicates the number of audio languages recorded. Up
to 8 languages can be recorded in a movie. You can
select a favorite language.
Prohibition Mark
8
Indicates the number of subtitled languages recorded.
Up to 32 languages can be recorded.
32
If a DVD disc has scenes shot from multiple angles, you
can select a favorite angle.
Discs with limited period of use
Do not leave discs with a limited period of use in this
unit. If you load an already expired disc, you may not
be able to remove it from this unit.
9
Indicates the type of screen for the image. The left mark
indicates that a wide image picture (16:9) is displayed
on a standard TV set screen (4:3) with a black band at
both the top and bottom of the screen (letter box).
16:9 LB
|
6
KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
For first use
Before using this unit for the first
time
Language Setup
Set a language used for screen display, DVD subtitles,
etc.
Demonstration mode setting
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode setting.
• “Language” item of the Setup menu (page 13)
DSP Setup
Display
Setting
To get clear sound, set the sound environment
according to the location and size of physically
installed speakers with reference to the followings:
“DEMO ON”
“DEMO OFF”
The Demonstration mode function is ON.
Cancel Demonstration mode (Normal mode).
• “MENU” > “SWPRE” of <Function Control> (page 11)
• Cabin selection (page 28)
• Speaker Setting (page 28)
1 Select Standby
Press the [SRC] button.
Select the “STANDBY” display.
• DTA (Digital Time Alignment) setting (page 29)
• X’Over setting (page 29)
2 Enter Function Control mode
Press the [ ] button for at least 1 second.
“FUNCTION” is displayed.
⁄
•
Setting “DSP SET” to “BYPASS” disables the settings related
to the DSP function. Refer to “DSP” > “DSP SET” of <Function
Control> (page 12).
3 Enter Menu mode
Turn the [AUD] knob to select “MENU”.
Press the [AUD] knob.
4 Set the Demonstration mode
Turn the [AUD] knob to select “DEMO”.
Press the [AUD] knob for at least 2 seconds.
Select the “DEMO OFF” display.
5 Exit Function Control mode
Press the [ ] button for at least 1 second.
⁄
•
These settings can be changed later.
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation of control panel
[SRC] Release
[FM+] [AM–]
Disc slot
[
]
ꢁ
USB Terminal
AV input
ꢀ D
] [
[
]
[DISP] [AUD]
[1] [2] [3] [4] [5] [6]
[
]
Muting volume upon reception of phone call
When there is a call, “CALL” is displayed and the audio
system is paused.
When the call ends, “CALL” disappears and the audio
system comes back on.
General functions
Power/Source Select button: [SRC]
Turns on the power.
When the power is on, the source switches between
Tuner (“TUNER”), USB or iPod (“USB” or “iPod”), DVD
(“DVD”), AV input (“AVIN”), and Standby (“STANDBY”)
each time this button is pressed.
The audio system also comes back on when [SRC] is
pressed during a call.
⁄
Press at least 1 second to turn off the power.
•
To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (page
37).
⁄
•
When an optional accessory is connected, the source name
for each device appears.
Volume control: [AUD] knob
Turn the knob to adjust the volume.
Tuner functions
FM band: [FM+]
Switches between FM1, FM2, and FM3 each time the
[FM+] button is pressed.
Subwoofer output: [AM–]
Switches between ON (“SW ON”) and OFF (“SW OFF”)
each time this button is pressed for at least 2 seconds.
AM band: [AM–]
Switches to AM.
⁄
•
You can do this function when “SWPRE” in <Function
Control> (page 11) is set to “SW”.
Tuning: [4]/ [¢]
Changes the frequency.
AV input
⁄
Connect an external player such as a digital audio
player to AV IN jack. Use of the optional cable CA-
C3AV is recommended for connecting an external
player.
•
Use the “MENU” > “AUTO1”/ “AUTO2”/ “MANUAL” in
<Function Control> (page 10) to change the frequency
switching.
•
During reception of stereo stations the “ST” indicator is ON.
⁄
Preset memory: [1] - [6]
Memorizes the station selected when pressing for at
•
The AV input requires the setting made in “MENU” > “AVIN”
of <Function Control> (page 11).
least 2 seconds.
Switching display: [DISP]
Changes the information displayed. Refer to page 14
Auto memory entry: [FM+]
Memorizes 6 stations with good reception
for the details of the display setting.
automatically when pressed for at least 2 seconds.
Text/Title scroll: [DISP]
Scrolls the text display of a CD or audio files when
pressed for at least 1 second.
Preset tuning: [1] - [6]
Recalls the memorized station.
|
8
KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD/ USB/ iPod play functions
Changing the audio channel
Changes the audio channel when this button is
pressed.
: [2]
Video CD
Disc play: Disc slot
Starts playing when a disc is inserted.
Repeat play: [4]
When a disc is inserted, the “IN” indicator is ON.
Each time you press the button, the Repeat Play
alternates between the modes.
⁄
•
Do not attempt to insert a disc into the slot if another one
is already there.
Chapter Repeat (“CHAP REP”), Title Repeat
(“TITL REP”) and OFF (“REP OFF”)
Chapter Repeat (“CHAP REP”), Program
Repeat (“PRG REP”) and OFF (“REP OFF”)
Track Repeat (“TRAC REP”) and OFF (“REP
OFF”) (Video CD: PBC Off)
DVD-VIDEO
DVD-VR
•
The unit can only play 12 cm (5 inch) discs. If you insert an
8 cm (3 inch) disc, it will get stuck inside and can cause the
unit to malfunction.
Video CD
C D
Disc ejection: [0]
⁄
File Repeat (“FILE REP”), Folder Repeat (“FOLD
REP”), and OFF (“REP OFF”)
Audio File
MPEG/DivX®
•
You can eject the disc for 10 minutes after switching off the
engine.
Folder Repeat (“FOLD REP”) and OFF (“REP
OFF”)
JPEG
USB device/iPod play: USB Terminal
Connecting a USB device starts playback.
File Repeat (“REP ONE”), All Repeat (“REP ALL”),
and OFF (“REP OFF”)
iPod
⁄
•
For the playable audio file, video file, media, and devices,
refer to <About Audio file> (page 4), <About Video file>
(page 4).
Random play
C D MPEG/DivX® iPod
Video CD Audio File
: [3]
Randomly plays the track/ file in the disc or folder.
When Random Play is turned on, “DISC RDM”/ “FOLD
RDM” is displayed.
USB device/ iPod removing
To disconnect the USB device/ iPod, stop the playback
by pressing the [1] button, and then disconnect the
USB device/ iPod.
⁄
•
iPod : Disabled when VIDEO is being played.
MPEG/DivX® iPod : [3]
Pause and play: [6]
All Random play
Audio File
Switches between pause and play each time this
button is pressed.
If you press this button for at least 3 seconds while
playing a file, all files in the media play at random
(“ALL RDM”).
Pressing the button again turns the random play off
(“RDM OFF”).
Stops playing: [1]
Track/File search: [4]/ [¢]
Changes the chapter/ track/ file when this button is
pressed.
Fast reverses or forwards the music while pressing.
Pressing these buttons for 5 seconds or longer
accelerates the speed of fast-forward or fast-reverse.
⁄
•
•
•
The time required to turn on the all random function may
become longer depending on the number of songs in iPod
or the folder structure.
iPod : Turning on the all random function changes
the iPod browse item to “songs”. This browse item will not
change even if the all random function is turned off.
iPod : If the brows item is changed to search for
music while the all random function is on, the all random
function is turned off and the songs in the browse item are
played at random.
⁄
•
For the iPod, the fast-forward or reverse speed does not
change.
Title/ Folder search
MPEG/DivX®
DVD-VIDEO DVD-VR Audio File
JPEG : [FM+]/ [AM–]
Changes the title/ folder.
Search mode
C D MPEG/DivX® JPEG
iPod
Audio File
: [
]
After pressing this button, you can quickly search
songs with the [AUD] knob. See <Music/Video
Search> (page 21) for details.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Control/ Setup Menu
Function Control
Functions in the table below can be set up by using Function Control.
Displayed item is depending on currently selected
1 Enter Function Control mode
Press the [ ] button for at least 1 second.
“FUNCTION” is displayed.
source or mode. The mark in Condition column
shows the condition to which the item is displayed.
: Can be set in other than standby state.
: Can be set in standby state.
2 Select your desired setup item
: Can be set only during playback of the iPod source.
(USB source used when the iPod is connected)
: Can be set during DVD source.
: Can be set during Tuner source.
: Can be set during FM reception.
Operation type
Operation
Movement between items Turn the [AUD] knob.
Selection of item
Return to previous item
Press the [AUD] knob.
Press the [ ] button.
: Can be set while accessing AV IN or AUX source.
: Can be set while HD Radio source.
: Can be set during Satellite radio source.
: Can be set for sources other than the standby
source by setting “2ZON” of <Audio Setup> (page
26) to “ON”.
Repeat selection and determination until your
desired setup item is selected.
In this manual, the above selection is indicated as
Press [ ] 1sec., and select “MENU” > “ICON”.
Category Function of setup item
“iPodCTRL” Allows you to set up iPod Control by Hand
Mode.
Condition
—
: Can be set during all sources.
⁄
“DSP”
Allows you to set up the sound environment.
•
•
•
Refer to the respective page for information on how to
set the items with reference page number.
Only the items available to the current source are
displayed.
Strong electrical fields (such as from power lines) may
cause unstable sound quality when CRSC is turned ON.
In such a situation, turn it OFF.
“MENU”
Allows you to set up the environment.
—
—
“RETURN” Exit Function Control mode.
3 Make a setting
Press the [AUD] knob or turn the [AUD] knob to
select a setting value, and then press the [AUD]
knob.
* Factory setting
• The value of items with [AUD] mark can be set by
pressing the [AUD] knob.
• The value of items with [4/ ¢] mark can be
set by pressing the [4] or [¢] button.
• Some items require you to keep pressing the
[AUD] knob for 1 or 2 seconds to set. For these
items, the time during which you need to keep
pressing the [AUD] knob is displayed in the Entry
column in seconds.
4 Exit Function Control mode
Press the [ ] button for at least 1 second.
|
10 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
“MENU”
Item
Setting
Entry Setting overview
Condition Page
Sets/Resets security code.
“CODE SET”/
“CODE CLR”
“DIM”
1 sec.
24
4
/
/
¢
¢
Adjusts the brightness of the display according to the surrounding
illumination.
Sets the Graphics mode of the display.
“OFF”*/“ON”
—
—
34
4
“ICON”
“OFF”/“ON1”/
“ON2”*
“R”*/“SW”/“AV”
4
/
/
¢
¢
Sets the preout output.
“SWPRE”
“ZONE2”
34
34
4
Specifies the destination of sub source sound when the Dual Zone
function is turned on.
“F”/“R”*
4/
¢
Selects the tuning mode of the radio/HD radio.
“AUTO1”/“AUTO2”/ “AUTO1”*/“AUTO2”/
33
“MANUAL”
“CRSC”
“MANUAL”
“OFF”/“ON”*
4/
¢
Switches to Monaural to decrease noise when reception is poor.
Sets the receive mode of HD Radio reception.
—
25
“HDR MODE”
“AUTO”*/“DIGITAL”/ 1 sec.
“ANALOG”
4/
¢
Sets the seek mode of satellite radio.
“CHANNEL”/
“PRESET”
“ESN=”
“NAME SET”
“M/V”
“ABOOK”
“SKIP”
“CHANNEL”*/
“PRESET”
31
Displays the Electronic Serial Number of satellite radio.
Sets the display when switched to AV IN or AUX source.
Displays the firmware version of Microvision.
Sets the audio book playback speed.
—
15
—
—
21
1 sec.
4
/
/
¢
¢
“SL”/“NM”/“FA”
4
Sets the ratio of skip performed with <Music/Video Search for
iPod>.
“0.5%”*/“1%”/
“5%”/“10%”
“OFF”/“ON”*
4
/
/
¢
¢
Specifies whether or not the artworks of the music files are
displayed.
Selects playback file type when a disc or USB contains different
types of files.
“iART”
—
13
4
“FILETYPE” >“DISC” “A/V”/“PIC”
>“USB”
You can make advanced settings in the “FILE TYPE” of the Setup
menu. “A” or “V” may appear on the display after setting.
Specifies whether the text is scrolled automatically.
4
/
/
¢
¢
“SCL”
“AVIN”
“AUTO”*/“MANU”
“OFF”/“ON1”*/
“ON2”
—
—
—
33
4
Sets whether to display AV IN during source selection.
Specifies whether to enable demonstration.
“DEMO”
“OFF”*/“ON”
2 sec.
7
“iPodCTRL”
Item
Setting
“HANDS ON”/
“MODE OFF”*
Entry Setting overview
Condition Page
“iPodCTRL”*1
22
When set to “HANDS ON”, allows you to operate iPod with the
AUD
control on the iPod.
“DSP”
Item
“CONTROL” “EQ”
Setting
Entry Setting overview
Condition Page
Sets the sound quality.
[AUD]
26
Sets the Bass Boost level in two steps.
“B.BOOST” “OFF”*/
“STEP1”/“2”
“HIGHWAY” “OFF”/
“STEP1”/“2”/
“3”*/“4”
—
AUD
Compensates the low volume or bass sound being lost by road
noises to make vocal sound clearer.
34
27
AUD
Compensates the sound environment in accordance with the
listening position.
“POSITION”
[AUD]
Next page 3
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Control/ Setup Menu
Item
“SETUP” “CABIN”
Setting
Entry Setting overview
Condition Page
Selects the car type to compensate the distance difference
[AUD]
28
between each speaker.
Sets the connected speaker, speaker size, and installation position.
“SPEAKER”
“DTA”
[AUD]
[AUD]
28
29
Makes fine adjustment of the compensation value specified at
Cabin.
Makes fine adjustment of the X’Over value specified at Speaker.
“X’OVER”
“PRESET” “RECALL”
[AUD]
[AUD]
29
30
Registering the value setup by Sound Control. Recalling the sound
setup registered by <Audio Preset Memory>.
Registering the value setup by Sound Control.
“MEMORY”
“DSP SET”
[AUD]
30
—
Setting “BYPASS” passes the DSP function.
Setting “THROUGH” activates the DSP function.
“BYPASS”/
“THROUGH”*
AUD
Setup menu of remote control
By using the Setup menu, you can make various adjustments to items such as picture and sound. You can
also set a language for the subtitles and the Setup menu, among other things.
1 Select DVD or USB source
Press the [SRC] button.
4 Press the [2]/[3] button to select the menu.
LANGUAGE/ PICTURE/ AUDIO/ OTHER
Select the “DVD” or “USB” display.
5 Press the [5]/[∞] button to select the desired
item, and then press the [ENTER] button.
✍ To cancel pop-up menu, press the [RETURN]
button.
2 Press the [7] button.
3 Enter Setup menu mode
Press the [SETUP] button.
6 Press the [5]/[∞] button to select the desired
setting, and then press the [ENTER] button to
confirm your selection.
7 Exit Setup menu mode
Press the [SETUP] button.
The Setup menu ends.
⁄
•
The memory cannot be erased by the Reset button.
|
12 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE
Item
Setting
Selects the initial disc menu language and audio language.
Refer to the language code list (page 35).
MENU LANGUAGE/
AUDIO LANGUAGE
SUBTITLE
ON SCREEN
LANGUAGE
Selects the initial subtitle language or remove the subtitle (OFF). Refer to the language code list (page 35).
Selects a language for the setup menu and on screen display.
PICTURE
Item
MONITOR TYPE
Setting
• 16:9: Select when a 16:9 wide TV is connected.
• 4:3 LETTERBOX: Select when a standard 4:3 TV is connected. Displays a wide picture with bands on the
upper and lower portions of the screen.
• 4:3 PAN SCAN: Select when a standard 4:3 TV is connected. Automatically displays the wide picture on the
entire screen and cuts off the portions that do not fit.
Selects the on-screen bar position on the monitor.
• 1: Higher position.
• 2: Lower position (Guidance below the disc setup menu will disappear.)
• ON: Displays the artwork of your iPod.
OSD POSITION
iPod ARTWORK
• OFF: Does not display the artwork of your iPod.
AUDIO
Item
DOWN MIX
Setting
• SURROUND COMPATIBLE: Uses multi-channel surround audio by connecting an amplifier compatible with
Dolby Surround.
• STEREO: Normally select this.
You can enjoy a powerful sound at low or middle volume levels while playing a Dolby Digital software.
• AUTO: Applies the effect to multi-channel encoded software (excluding 1-channel and 2-channel software).
• ON : Uses this function always.
D.RANGE
COMPRESSION
OTHER
Item
DivX REGISTRATION
Setting
This unit has its own Registration Code. Once you have played back a disc in which the Registration Code
recorded, this unit’s Registration Code is overwritten for copyright protection.
1. Press the [ENTER] button to show Code.
2. Press the [ENTER] button to exit.
⁄
•
When downloading a DivX VOD file controlled by DRM, register the code appeared on the screen such as
the one above. Otherwise the file may not be able to play with this unit. Remaining number of viewing
is displayed when playing a DivX VOD file with the viewing restriction. When the remaining number of
viewing reached 0, a warning message appears and the file cannot be played.
Selects playback file type when a disc or USB contains different types of files.
• AUDIO: Play Audio file (MP3, WMA, WAV).
• STILL PICTURE: Play JPEG file.
FILE TYPE (DISC)/
FILE TYPE (USB)
• VIDEO: Play Video file (MPEG, DivX).
• AUDIO+VIDEO: Play Audio or Video file.
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/ Display Settings
In iPod source
Information
Music title & Artist name
Album name & Artist name
Play time & Music number
Clock
Manual Clock Adjustment
Display
“TITLE”
“ALBUM”
“P-TIME”
“CLOCK”
1 Select the Clock display
Press the [DISP] button.
2 Enter Clock adjustment mode
Press the [DISP] button for at least 1 second.
The clock display blinks.
In Standby/ AV input source
Information
Source name
Clock
Display
“SRC NAME”
“CLOCK”
3 Adjusting Clock
Operation type
Adjust the hours
Adjust the minutes
Operation
Press the [FM+] or [AM–] button.
Press the [
4] or [¢] button.
In HD Radio source (Optional)
Information
Station name
Title
Display
“ST NAME”
“TITLE”
4 Exit Clock adjustment mode
Press the [DISP] button.
Frequency
Clock
“FREQ”
“CLOCK”
Text Display Selection
In SIRIUS/ SAT source (Optional)
Changing displayed information on each source
following;
Information
Channel Name
Music Title
Display
“CH NAME”
“SONG”
In Tuner source
Information
Frequency
Clock
Display
“FREQ”
“CLOCK”
Artist Name
“ARTIST”
Composer name
Category Name
Label Name
Comment
Band & Channel Number
Clock
“COMPOSER”
“CATEGORY”
“LABEL”
“COMMENT”
“CH NUM”
“CLOCK”
In DVD/ Video CD source
Information
Title number & Chapter number/
Program number & Chapter number
Track number & Play time*2
Clock
Display
“TNO : CNO”*1
“PNO : CNO”*1
“P-TIME”
In XM source (Optional)
“CLOCK”
Information
Channel Name
Title
Display
“CH NAME”
“TITLE”
*1 DVD-VIDEO or DVD-VR only
*2 Track number and play time are not displayed with
Video CD PBC On.
Name
“NAME”
Category Name
Band & Channel Number
Clock
“CATEGORY”
“CH NUM”
“CLOCK”
In CD & External disc source
Information
Disc title
Track title
Play time & Track number
Clock
Display
“D-TITLE”
“T-TITLE”
“P-TIME”
“CLOCK”
Select the text
Press the [DISP] button.
⁄
In Audio file/ Video file/ JPEG file source
•
•
•
When you select the clock display, the display setting of
each source will be changed to the clock display.
If the selected display item does not have any
information, alternative information is displayed.
If the iPod Control by Hand Mode is set to on while
playing the iPod, “iPodMODE” is displayed.
Information
Display
“TITLE”*1
“ALBUM”*1
“FOLDER”
“FILE”
Title & Artist name
Album name & Artist name
Folder name
File name
Play time & File number*1
Clock
“P-TIME”
“CLOCK”
*1 “JPEG” is displayed when a file is JPEG.
|
14 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
AV Input Display Setting
Theft Deterrent Faceplate
Selecting the display when changing to AV IN or
AUX source.
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
1 Select AV IN source
Press the [SRC] button.
Select the “AVIN” display.
Removing the Faceplate
Press the Release button.
The faceplate unlocks, allowing you to detach it.
¤
2 Enter AV input display setting mode
Press [ ] 1 sec., and select “MENU” > “NAME
SET”.
Press the [AUD] knob for at least 1 second.
The presently selected AV input display is displayed.
•
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
•
•
Keep the faceplate in its faceplate case while detached.
Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
3 Select the AV input display
Turn the [AUD] knob.
•
To prevent deterioration, do not touch the terminals of
the unit or faceplate with your fingers.
“AVIN”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
Reattaching the Faceplate
Refer to the following diagram when
reattaching the faceplate.
4 Exit AV input display setting mode
Press the [ ] button.
⁄
•
When operation stops for 10 seconds, the name at that
time is registered, and the AV input display setting mode
closes.
•
The AV input display can be set only when the built-in
AV input or the auxiliary input of optional KCA-S220A
is used. On the KCA-S220A, “AUX EXT” is displayed by
default.
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc/ USB Operations of Remote Control
Fast Forwarding or Fast Backwarding
Press the [1] or [¡] button repeatedly to
select the required speed.
Before Use
•
Turn on the monitor to watch the playback picture.
If you turn on the monitor, you can also control
playback of other discs by referring to the monitor
screen.
x2, x5, x10, x20, x60
C D
DVD-VIDEO DVD-VR Video CD
Audio File
1, 2, 3 MPEG/DivX®
•
Set the remote controller mode switch to “DVD”
mode before starting operation, refer to <Remote
Controller mode switch> (page 32).
DVD-VIDEO DVD-VR
Slow Forwarding or Backwarding
Video CD
1 Press the [38] button to pause.
2 Press the [1] or [¡] button repeatedly to
select the required speed.
Playing a Disc
1/32, 1/16, 1/8, 1/4, 1/2
Inserting a disc in the unit
“READING” appears on the display, and playback
starts automatically.
⁄
•
Slow motion playback in reverse is not possible with
DVD-VR or Video CDs.
✍ If playback does not start, press [38].
✍ In some cases, the disc menu might appear
instead.
Forward frame-by-frame playback
Video CD
1 Press the [38] button to pause.
2 Press the [¢] button.
DVD-VIDEO DVD-VR
⁄
•
The menu screen may be displayed first after loading a DVD
or Video CD 2.0 which offers a menu.
5 minutes skip MPEG/DivX®
Press the [2] or [3] button.
Skips from the head of a file at five-minute intervals.
•
DVDs may have a region code. Your player does not play
discs that have a region code different from your player.
About the region code, refer to Region code (page 6).
The playback file may be different depending on the file
type set for Audio, Video and JEPG files. (page 13)
Example: 1:23 = 5:00 = 10:00
•
⁄
•
The operation is enabled when the Status and Control
bars are not displayed.
Camera angle
DVD-VIDEO
Playing a USB device
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback.
Press the [ANGLE] button repeatedly during
playback to select a desired angle.
The number of the current angle appears on the
display.
Connecting the USB device
For a USB device that includes audio files, video
files, or photo files, “READING” appears in the
display, and playback starts automatically.
⁄
•
The playback file may be different depending on the file
type set for Audio, Video and JEPG files. (page 13)
Subtitles
MPEG/DivX®
DVD-VIDEO DVD-VR
Press the [SUBTITLE] button repeatedly
during playback to see the different subtitle
languages.
Basic Operation
Playing or pausing
Press the [38] button.
Changing the audio stream
MPEG/DivX®
DVD-VIDEO DVD-VR
Stopping the play
Press the [7] button.
Press the [AUDIO] button repeatedly during
playback to hear a different audio stream.
Searching for a chapter/ scene/ track/ file
Changing the audio channel
Video CD
Press the [4] or [¢] button.
Press the [AUDIO] button repeatedly during
playback to hear a different audio channel
(STEREO, Left or Right).
Selecting a title/ folder
MPEG/DivX®
DVD-VIDEO DVD-VR
JPEG Audio File
Press the [FM+] or [AM–] button.
|
16 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Changes the audio stream.
Displaying Status and Control
on-screen
Changes the subtitle language.
DVD-VIDEO DVD-VR Video CD
MPEG/DivX® JPEG
Switches the Track time (“TIME”), remaining
track (“REM”), Disc time (“TOTAL”), and
remaining disc (“T.REM”).
Refer to <Time search> (page 18).*1
Video CD
You can display various information about the disc
loaded on-screen.
Example: DVD-VIDEO
Direct Track Search.*1
Status bar
Switches the Track repeat (“TRACK”), and repeat
off (“OFF”).*1
Switches the Disc random (“ALL”), and random
off (“OFF”).*1
Changes the audio channel.
Control bar
Switches the File repeat (“TRACK”), Folder
repeat (“FOLDER”), and repeat off (“OFF”).
Switches the Folder random (“FOLDER”), All
random (“ALL”), and random off (“OFF”).
Changes the audio language.
MPEG/DivX®
JPEG
Status bar
1 Disc type
2 DVD: Audio signal format type and channel
Video CD: PBC
3 Playback mode
Changes the subtitle language.
“T.RPT” (Title/ Track repeat), “C.RPT” (Chapter
repeat), “PG.RPT” (Program repeat), “F.RPT”
(Folder repeat)
Switches the Folder repeat (“FOLDER”), and
repeat off (“OFF”).
*1 While PBC is not in use.
“F.RND” (Folder random), “A.RND” (All random)
4 Playback information
“T” (Title/ Track), “C” (Chapter), “PG” (Program),
“PL” (Play list), “F” (Folder/ File)
5 Time indication
1 Press the [OSD] button during playback.
Pressing the button repeatedly selects Status bar,
Status & Control bar, and Status bar off sequentially.
2 Press the [2] or [3] button during control bar
on-screen to select an item. Press the [ENTER]
button.
6 Playback status
“3” (Play), “8” (Pause), “7” (Stop), “¡”/”1”
(Forward/reverse search), “ ”/” ” (Forward/
reverse slow-motion)
✍ To cancel pop-up menu, press the [RETURN]
button.
Control bar
3 Press the [5] or [∞] button to change or select
Format
Icon
Operation
the setting. Press the [ENTER] button.
Switches the Chapter time (“TIME”), remaining
chapter (“REM”), Title time (“TOTAL”), and
remaining title (“T.REM”).
DVD-VIDEO
⁄
•
If any button is not pressed for a few seconds, the
on-screen display disappears.
Refer to <Time search> (page 18).
Direct Title Search.
Direct Chapter Search.
Switches the Chapter repeat (“CHAPTER”), Title
repeat (“TITLE”), and repeat off (“OFF”).
Changes the audio stream.
Changes the subtitle language.
Changes the camera angle.
Switches the Program/ Play list time (“TOTAL”),
remaining program/ play list (“T.REM”).
Refer to <Time search> (page 18).
DVD-VR
Direct Chapter Search.
Switches the Chapter repeat (“CHAPTER”),
Program repeat (“PROGRAM”), and repeat off
(“OFF”).
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc/ USB Operations of Remote Control
DVD-VIDEO Disc Menu
Zoom
DVDs may offer menus that allow you to access
special features.
The zoom function allows you to enlarge the video
image.
DVD-VIDEO DVD-VR Video CD MPEG
Press the [ZOOM] button repeatedly during
playback or in the pause mode to enlarge the
image.
1 Press the [MENU] button
The disc menu is displayed.
2 Use the [5]/[∞]/[2]/[3] button to highlight
your selection, then press the [ENTER] button.
OFF, 1 – 6
3 To return to the first menu feature, press the
[TOP MENU] button again.
✍ You can move through the zoomed picture
using [5]/[∞]/[2]/[3].
4 To remove the disc menu, press the [MENU]
button again.
JPEG
1 Press the [38] button to pause
2 Press the [ZOOM] button repeatedly to
enlarge the image
OFF, 1, 2
DVD-VR Menu
✍ You can move through the zoomed picture
using [5]/[∞]/[2]/[3].
Selects an option from the DVD-VR Disc menu.
1 Press the necessary operation button
In case of Program list : [TOP MENU]
In case of Play list : [MENU]
Time Search
DVD-VIDEO DVD-VR Video CD
The Time Search function allows you to start playing
at any chosen time on the disc.
1 Press the [OSD] button twice briefly during
playback
2 Press the [2] or [3] button to select the Time
Search icon in the on-screen display. Press the
[ENTER] button.
2 Use the [5] or [∞] button to highlight your
selection, then press the [ENTER] button
✍ To remove the disc menu, press the [MENU]
button or the [TOP MENU] button again
The “_: _ _: _ _” appears in the Time Search box.
3 Press the [5] or [∞] button to change the
number, then press the [2] or [3] button to
move to the next entry
4 Press the [ENTER] button to confirm the start
time
Playback starts from the selected time on the disc.
✍ If you enter an invalid time, playback will
continue from the current point.
Video CD PBC Menu
Press [RETURN] to return to the menu screen.
Menu settings and operating procedures may
differ. Follow the instructions on the each menu
screen.
Canceling the PBC playback
1 Press the [7] button to stop
2 Press the [DIRECT] button
3 Press the number buttons
Direct Search
Searching the chapter by entering the number.
1 Select the search mode
Press the [DIRECT] button.
Each time you press the button, the search mode
alternates between the modes.
4 Press the [ENTER] button
✍ To resume PBC, press [TOP MENU] or [MENU].
Chapter search (“CHAP”), Title search
(“TITL”), and Search mode off.
DVD-VIDEO
|
18 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter search (“CHAP”), Program/Play
list search (“PRGM”/ ”PLST”), and Search
mode off.
DVD-VR
⁄
•
An image is displayed at the folder list position when an
album art is attached to the tag of a playing audio file.
Track search (“TRAC”/“NMBR”) and Search
mode off.
Video CD
C D
To select a playback mode
Track search (“TRAC” or “Track Search”),
Folder search (“FOLD” or “Folder Search”),
and Search mode off.
MPEG/DivX®
Audio File
1 Show the Playback mode selection screen
Press the [OSD] button.
File search (“FILE”, “TRAC” or “Track Search”),
Folder search (“FOLD” or “Folder Search”),
and Search mode off when pressed while
playing a JPEG.
JPEG
2 Press the [2] or [3] button to select a
playback mode MPEG/DivX®
C D
Audio File
2 Press the number buttons
3 Press the [ENTER] button
⁄
“REPEAT”/ “RANDOM”
3 Press the [5] or [∞] button to select an item
“REPEAT”: Track/File repeat*1 (“TRACK”), Folder
repeat*2 (“FOLDER”), and repeat off
(“OFF”).
•
•
Direct Search cannot be performed during Random play.
The Search mode is cleared automatically after
approximately 5 seconds.
“0” is not displayed in the first digit by pressing the [0]
button.
“RANDOM”*1: Folder random (“FOLDER”), All
random (“ALL”), and random off
(“OFF”).
•
Example: “- -” = Press [0], [2] = “- 2”.
*1 Not selectable for JPEG
*2 Not selectable for CD
4 Press the [ENTER] button
File Select MPEG/DivX® JPEG
C D
Audio File
You can select a file from the list display.
List screen
1 Press the [7] button to stop
1 Folder list
2 Track information
3 Track list
2 Show the list screen
Press the [MENU] or [TOP MENU] button.
1 Show the control screen
3 Select an item from the folder list
Use [5]/[∞]/[2]/[3] to highlight your selection,
and then press the [ENTER] button.
MPEG/DivX® JPEG Press the [7] button to stop.
C D
Automatically appear during
play.
Audio File
4 Select a track to start playing
Use [5]/[∞]/[2]/[3] to highlight your selection,
and then press the [ENTER] or [3] button.
✍ To go back to the folder list, press the [RETURN]
button.
2 Press [2] or [3] to select “Folder” column or
“Track” column MPEG/DivX® JPEG
Audio File
3 Press the [5] or [∞] button to select a folder or
track
5 To remove the List screen, press the [MENU]
button again.
4 Start playback
MPEG/DivX® JPEG Press the [ENTER] button.
Audio File
C D
Playback starts automatically.
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod Operations of Remote Control
Before Use
3 Search for music/video
Operation type Operation
Movement between items Press the [
•
Video output setting of iPod needs to be set on
your iPod.
5
] or [
Press the [ENTER] or [
Press the [ ] or [MENU] button.
Press the [TOP MENU] button.
∞
] button.
•
Turn on the monitor to watch the playback picture.
If you turn on the monitor, you can also control
playback of other discs by referring to the monitor
screen.
Selection of item
3
] button.
Return to previous item
Return to Top menu
2
Cancelling the Search mode Press the [RETURN] button.
•
Set the remote controller mode switch to “DVD”
mode before starting operation, refer to <Remote
Controller mode switch> (page 32).
⁄
•
•
An image is displayed in the category list when a playing
song has artwork with “MENU” > “iART” (page 11) of the
<Function Control> set to ON.
It takes some seconds to read artwork. You cannot
operate during the read operation.
Playing the iPod
Connecting the iPod
“READING” appears in the display, and playback
starts automatically.
To select a playback mode
1 Show the Playback mode selection screen
Playing or pausing
Press the [38] button.
Press the [OSD] button.
Stopping the play
Press the [7] button.
2 Select a playback mode
Searching for a chapter/ scene/ track/ file
Press the [4] or [¢] button.
Press the [2] or [3] button.
“REPEAT”/ “RANDOM”/ “AUDIO BOOK”
Fast Forwarding or Fast Backwarding
Press the [1] or [¡] button.
3 Select an item
Press the [5] or [∞] button.
“REPEAT”: File repeat (“ONE”), All repeat (“ALL”), and
repeat off (“OFF”).
Search Mode
“RANDOM”: Song random (“SONGS”), Album
random* (“ALBUMS”), and random off
(“OFF”).
You can select a file from the list display.
“AUDIO BOOK”: Normal speed (“NORMAL”), Faster
speed (“FASTER”), and Slower speed
(“SLOWER”).
4 Press the [ENTER] button
⁄
•
* Functions only if you select “All Albums” or “All” in
“Albums” of the main “MENU”.
1 Category list
2 Track information
3 Track list
1 Enter Search mode
Press the [TOP MENU] or [MENU] button.
2 Select an menu item
Press the [5] or [∞] button to select an menu
Music/ Videos/ Shuffle Songs
|
20 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Music disc/Audio file/iPod Operation of Control Panel
Music/Video Search for iPod
Music/Video Search
C D MPEG/DivX®
Audio File
Search for the song/ video (in iPod) you want to
play.
JPEG
Selecting the track/ file you want to listen to from
the device or media being played now.
1 Enter Music/Video Search mode
Press the [ ] button.
“SEARCH” is displayed.
1 Enter Music/Video Search mode
Press the [ ] button.
“SEARCH” is displayed.
2 Search for song/ video
Displays the current Audio file name.
Operation type
Operation
Movement between items Turn the [AUD] knob.
2 Search for track/ file
Audio File MPEG/DivX® JPEG
Skip Search *1
Press the [4] or [¢] button.
Selection of item
Return to previous item
Return to Top menu
Press the [AUD] knob.
Operation type
Movement between
folders/files
Operation
Turn the [AUD] knob, or press the [FM+]/
[AM–] button.
Press the [FM+] button.
Press the [FM+] button for at least 1
second.
Selection of folder/flie
Return to previous folder Press the [
Return to root folder
Press the [AUD] knob or [
¢
] button.
Search by initial
Press the [ ] button for at least 1 second.
4
Press the [
second.
] button.
] button for at least 1
The position of the currently displayed item is
indicated by the icon bar in eight steps.
4
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
: Indicates that your selection is a folder.
: Indicates that your selection is a file.
✍ The folder tree is not displayed and only folders
with files are displayed in order. Refer to <Playing
order of the Audio file> (page 4).
Cancelling the Music/Video Search mode
Press the [ ] button.
Searching for Music by Initial
You can select an alphabetic character from the list
in the browse item (artist, album, etc.) selected now.
C D
Operation type
Operation
1 Enter alphabet search mode
Press the [ ] button for at least 1 second.
“A B C …” is displayed.
Movement between track Turn the [AUD] knob, or press the [FM+]/
[AM–] button.
Selection of track
Press the [AUD] knob.
•
If you can not search for a song by an alphabetic
character in the browse item selected now, the data on
the screen does not change.
Return to first track
Press the [
second.
4] button for at least 1
2 Select the initial to be searched for
Operation type Operation
Move to the next character. Turn the [AUD] knob, or press the
Cancelling the Music/Video Search mode
Press the [ ] button.
⁄
[
4
]/ [ ] button.
¢
•
Music/Video Search cannot be performed during
Random play.
Move to the next row.
Cancelling the alphabet
search mode
Press the [FM+] or [AM–] button.
Press the [ ] button.
3 Determine the selected initial
Press the [AUD] knob.
Start search. When search is completed, the
Music/Video Search mode is selected again at the
selected character position.
⁄
•
*1 Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs
Next page 3
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Music disc/Audio file/iPod Operation of Control Panel
in the list which is selected now. Set the ratio with
“SKIP” in <Function Control> (page 11). Keep pressing
iPod Control by Hand Mode
Allows you to operate iPod with the control on the
iPod.
this button for 3 seconds or longer skips songs at 10%
irrespective of the setting.
The time of search by alphabet may become long
depending on the number of songs in iPod or the folder
structure.
When selecting an initial in the alphabet search mode,
entering “*” searches symbols and entering “1” searches
digits.
If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
•
•
•
Display
Setting
“HANDS ON”
“MODE OFF”
iPod control by hand mode is ON.
iPod control by hand mode is OFF.
1 Enter iPod Control by Hand Mode
Press [ ] 1 sec., and select “iPodCTRL”.
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
2 Set the iPod Control by Hand Mode
Turn the [AUD] knob.
3 Exit iPod Control by Hand Mode
Press the [ ] button.
⁄
•
•
•
In the iPod Control by hand mode, iPod cannot be
operated using this unit.
This mode is not compatible with music information
display. The display will show “iPodMODE”.
The following iPods cannot be controlled using this unit.
iPod nano (1st generation), and iPod with video. (KCA-
iP101 (optional accessory) connected only.)
In the iPod Control by hand mode, video is output to the
AV input of this unit. Nothing is displayed without video
output from the iPod.
•
•
When you cancel the hand mode while playing a video
file, the video file stops and a music file starts.
|
22 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching the music by entering the track
number (Direct Music Search)
1 Set the remote controller mode switch to
“AUD” mode
2. Press the number buttons on the remote
control.
Basic Operation of Disc Changer
(Optional)
Selecting CD changer source
Press the [SRC] button.
Select the “CD CH” display.
3. Press the [4] or [¢] button.
✍ Press the [38] button to cancelling Direct
Music Search.
Playing or pausing
Press the [6] button.
Music search
⁄
•
Press the [4] or [¢] button.
Changes the music when this button is pressed.
Fast reverses or forwards the music while pressing.
Direct Music Search cannot be performed during playing
of Random play, or scan play.
Searching the disc by entering the disc number
(Direct Disc Search)
1 Set the remote controller mode switch to
“AUD” mode
2. Press the number buttons on the remote
control.
3. Press the [FM+] or [AM–] button.
✍ Press the [38] button to cancelling Direct
Disc Search.
Disc Search
Press the [FM+] or [AM–] button.
Playing the Current Song or Disc Repeatedly
(Repeat play)
Press the [4] button.
Pressing the button repeatedly selects Track Repeat
play on (“TRAC REP”), Disc Repeat play on (“DISC
REP”), and Repeat play off (“REP OFF”) sequentially.
⁄
Playing the first part of each music on the disc
(Scan play)
Press the [2] button.
Successively plays the intro of the music in the disc.
When Scan Play is turned on, “TRAK SCN” is
displayed.
•
Direct Disc Search cannot be performed during playing
of Random play, or scan play.
•
Input “0” to select disc 10.
⁄
•
Set the remote controller mode switch to “AUD” mode
before starting operation, refer to <Remote Controller mode
switch> (page 32).
⁄
•
To use the functions written as the [SCN] button in the
option manual, press the [2] button.
Playing all the music on the disc in random
order (Random play)
Press the [3] button.
Randomly plays the music in the disc.
When Random Play is turned on, “DISC RDM” is
displayed.
Playing the music in the disc changer randomly
(Magazine random play)
Press the [5] button.
Pressing the button toggles the setting between
Magazine random play on (“MGZN RDM”) and off
(“RDM OFF”).
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
Other Functions
Function of KDV-MP5042U
Activating Security Code
Frequency Step Setting
When Security Code is set, possibility of theft
is reduced because input of Security Code is
prompted to turn on the unit once it is turned off.
Changing the tuning frequency step.
The original setting is FM band 50 kHz.
⁄
1 Turn the power OFF
•
You can set the Security Code with a 4 digit number of your
choice.
Press the [SRC] button for at least 1 second.
2 Switch the frequency step
•
The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
While pressing the [1] and [5] buttons, press the
[SRC] button.
1 Select Standby
Release your fingers from the button after the
display appears.
The frequency step changes to FM band 200 kHz.
Press the [SRC] button.
Select the “STANDBY” display.
2 Enter Security Code mode
⁄
Press [ ] 1 sec., and select “MENU” > “CODE SET”.
Press the [AUD] knob for at least 1 second.
When “ENTER” is displayed, “CODE” is also displayed.
•
When the same operation is repeated, the frequency
step returns to the original setting.
•
When the frequency step is changed, the frequencies in
the memory are deleted.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
3 Enter Security Code
Operation type
Select the digits to enter
Select the Security Code
numbers
Operation
Press the [
Turn the [AUD] knob, or press the
[FM+]/ [AM–] button.
4
] or [¢] button.
4 Confirm the Security Code
Press the [AUD] knob for at least 3 seconds.
When “RE-ENTER” is displayed, “CODE” is also
displayed.
5 Do the step 3 through 4 operation, and reenter
the Security Code.
“APPROVED” is displayed.
The Security Code function activates.
⁄
•
•
•
If you enter the wrong Code in steps 3 through 4, repeat
from step 3.
When the Security Code function is activated, “CODE
SET” changes to “CODE CLR”.
To deactivate the Security Code function, see the next
section <Deactivating Security Code>.
6 Exit Security Code mode
Press the [ ] button.
|
24 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Security Code
Receive mode Setting
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
Setting the receiver mode as follows;
Receive mode Display Operation
Auto mode
“AUTO”
Automatically tunes to analog broadcast
when there is no digital broadcast.
1 Turn the power ON.
2 Do the step 4 through 5 operation, and enter
Digital
Analog
“DIGITAL” Digital broadcasts only.
“ANALOG” Analog broadcasts only.
the Security Code.
“APPROVED” is displayed.
Now, you can use the unit.
1 Select HD Radio source
Press the [SRC] button.
Select the “HD RADIO” display.
2 Enter Receive mode
Deactivating Security Code
Press [ ] 1 sec., and select “MENU” > “HDR
MODE”.
Deactivating the Security Code function.
Press the [AUD] knob for at least 1 second.
For how to select Function Control items, refer to
<Function Control> (page 10).
1 Select Standby
•
Press the [SRC] button.
Select the “STANDBY” display.
3 Set the Receive mode
Turn the [AUD] knob, or press the [FM+]/ [AM–]
button.
2 Enter Security Code mode
Press [ ] 1 sec., and select “MENU” > “CODE CLR”.
Press the [AUD] knob for at least 1 second.
When “ENTER” is displayed, “CODE CLR” is also
displayed.
4 Exit Receive mode
Press the [ ] button.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
3 Enter Security Code
Operation type
Select the digits to enter
Select the Security Code
numbers
Operation
Press the [
Turn the [AUD] knob, or press the
[FM+]/ [AM–] button.
4
] or [¢] button.
4 Press the [AUD] knob for at least 3 seconds.
“CLEAR” is displayed.
The Security Code function deactivates.
5 Exit Security Code mode
Press the [ ] button.
⁄
•
If a wrong security code is entered, “ERROR” is displayed.
Enter a correct security code.
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
•
AV output source
Audio Control
The sub source (DVD, USB, and AV IN) can be output to
the AV output separately from the main source.
- Set the preout to “AV” in “MENU” > “SWPRE” (page 11) of
<Function Control>.
- Adjust the volume of AV output source by <Audio
Control> (page 26).
You can adjust following Audio Control items ;
Adjustment Item Display
Rear volume “R-VOL”
AV output volume “AVVOL”
Range
0 — 35
0 — 35
Subwoofer level
Balance
Fader
“SW L”
“BAL”
“FAD”
–15 — +15
Left 15 — Right 15
Rear 15 — Front 15
- “USB” and “DVD” cannot be set at the same time for the
main and AV output sources.
Dual Zone System and the AV output source cannot
be used at the same time. Turn off the setting currently
used and then set the next function.
•
Exit Audio Control mode (Volume control mode)
1 Select the source to adjust
1 Select the source to adjust
Press the [SRC] button.
Press the [SRC] button.
2 Enter Audio Control mode
2 Enter Audio Setup mode
Press the [AUD] knob.
Press the [AUD] knob for at least 1 second.
3 Select the Audio item to adjust
3 Select the Audio Setup item to adjust
Press the [AUD] knob.
Press the [AUD] knob.
4 Adjust the Audio item
4 Adjust the Audio setup item
Turn the [AUD] knob.
Turn the [AUD] knob.
5 Exit Audio Control mode
Press any button.
Press a button other than the [AUD] knob or [0]
button.
5 Exit Audio Setup mode
Press the [AUD] knob for at least 1 second.
Preset Equalizer Select
Audio Setup
You can select following Equalizer curve;
You can set Sound system, such as follows;
Preset Equalizer Display
Preset Equalizer Display
User*
Rock
Pops
Easy
Top 40
“USER”
“ROCK”
“POPS”
“EASY”
“TOP40”
Jazz
Game
iPod (During iPod
source only)
Natural
“JAZZ”
“GAME”
“iPod”
Adjustment Item Display
Volume offset “V-OFF”
Dual Zone System “2ZON”
Range
–8 — 0 (AV IN: -8— +8)
OFF/ DVD/ USB/ AV IN
OFF/ DVD/ USB/ AV IN
AV output source
“AV/O”
“NATURAL”
⁄
* The Equalizer curve set in the section <Manual Equalizer
Control> is recalled.
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
1 Enter Preset Equalizer mode
Press [ ] 1 sec., and select “DSP” > “CONTROL” >
“EQ” > “PRESET”.
•
Dual Zone System
Main source and sub source (DVD, USB, AV IN) output
Front channel and Rear channel separately.
- Set the preout to “R” or “SW” in “MENU” > “SWPRE” (page
11) of <Function Control>.
- Set up the channel of sub source by “ZONE2” of
<Function Control> (page 11).
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [AUD] knob.
- Adjust the volume of Rear channel by <Audio
Control> (page 26) or [5]/[∞] button on the remote
control (page 32).
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
2 Select the Equalizer curve
Turn the [AUD] knob and push the center when
the desired item is displayed.
You can select from 22 Equalizer curve types for
iPod when “iPod” is selected.
- The Audio Control has no effect on sub source.
- “USB” and “DVD” cannot be set at the same time for the
main and sub sources.
Select the iPod Equalizer curve
1. Enter iPod Equalizer mode
Press the [AUD] knob.
|
26 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select the iPod Equalizer curve
Turn the [AUD] knob and push the center when
the desired item is displayed.
Preset position “PRESET”
Adjustment Item Display
Not compensating. “ALL”
Adjustment Item Display
Front-Right seat
Front seat
“F-RIGHT”
“F-ALL”
Front-Left seat
“F-LEFT”
3 Exit Preset Equalizer mode.
Press the [ ] button.
Manual position “MANUAL”
Adjustment Item Display Adjustment Item Display
Front Left speaker “F-LEFT”
Front Right speaker “F-RIGHT” Subwoofer Right
Rear Left speaker “R-LEFT”
Rear Right speaker “R-RIGHT”
⁄
•
You can select for each source.
Subwoofer Left
“SW-LEFT”
“SW-RIGHT”
Initialize the setting “INITIAL”
values.
Manual Equalizer Control
1 Enter Preset position setting mode
Press [ ] 1 sec., and select “DSP” > “CONTROL” >
“POSITION” > “PRESET”.
You can adjust following Equalizer Control items;
Adjustment Item
Range
-9 – 0 – +9
“OFF”/“ON”
Press the [AUD] knob.
Band level “BAND#”>“GAIN”
Bass Effect* “BAND1”>“EFFECT”
•
For how to select Function Control items, refer to
<Function Control> (page 10).
•
*Can be only set for “BAND1”.
2 Select the seat you want to compensate
Turn the [AUD] knob and push the center when
the desired item is displayed.
1 Enter Manual Equalizer Control mode
Press [ ] 1 sec., and select “DSP” > “CONTROL” >
“EQ” > “MANUAL”.
3 Exit Preset position setting mode
Press the [AUD] knob.
Press the [ ] button.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
You can fine-adjust your listening position.
2 Select the band you want to set
Turn the [AUD] knob and push the center.
“BAND1” – “BAND5”
1 Enter Manual position adjust mode
Press [ ] 1 sec., and select “DSP” > “CONTROL” >
“POSITION” > “MANUAL”.
Press the [AUD] knob.
3 Select the item you want to set
Turn the [AUD] knob and push the center.
2 Select the speaker you want to set
Turn the [AUD] knob and push the center.
✍ Selecting “INITIAL” initializes the Manual position
adjustment.
4 Set the value
Turn the [AUD] knob and push the center when
the desired item is displayed.
3 Set the value
5 Exit Manual Equalizer Control mode
Turn the [AUD] knob and push the center when
the desired value is displayed.
Adjust between 0 and 5.58 feet.
Press the [ ] button twice.
⁄
•
When “iPod” is selected in the section <Preset Equalizer
select> (page 26), Manual Equalizer Control is disabled.
You can select for each source.
4 Exit Manual position adjust mode
•
Press the [ ] button twice.
⁄
•
About the position setting
First, set the using environment with <DTA (Digital Time
Alignment) Setting> (page 29).
When using the Subwoofer Left and Subwoofer Right as
a single sub woofer, set the left side and right side to the
same value.
Position Control
•
According to the listening position, select the
position from the following settings so that the
normal position of the sound environment can
be compensated in accordance with the selected
position;
English
|
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Cabin Selection
Speaker Setting
You can compensate the delay of the sound arrival
time by selecting your environment from the
following car types;
Setting the speaker to be connected, speaker size,
and installation position;
Setting item
Range
Car type
Not compensating. “OFF”
Compact car
Full size car
Station wagon
Display
Car type
Minivan
Display
“MINIVAN”
Front Speaker Location
“FRONT”>“LOCATION”
Front Speaker Size
“FRONT”>“SIZE”
Front Tweeter
“FRONT”>“TWEETER”
Rear Speaker Location
“REAR”>“LOCATION”
“DOOR”/“ON DASH”/“UND DASH”(Under
dash)
O.E.M/ 4 inch/ 5 inch/ 6½ inch/ 6¾ inch/
7 inch/ 4×6/ 5×7/ 6×8/ 6×9/ 7×10
“NONE”/“USE”
“COMPACT” Sport-utility vehicle “SUV”
“FULLSIZE” Minivan long
“WAGON”
“MV LONG”
•“DOOR”/“R-DECK”
•“2ND ROW”/“3RD ROW”(Minivan/
Minivan long)
None/ O.E.M/ 4 inch/ 5 inch/ 6½ inch/
6¾ inch/ 7 inch/ 4×6/ 5×7/ 6×8/
6×9/ 7×10
None/ 6½ inch/ 8 inch/ 10 inch/ 12 inch/
15 inch over
1 Enter Cabin select mode
Press [ ] 1 sec., and select “DSP” > “SETUP” >
“CABIN”.
Front Speaker Size
“REAR”>“SIZE”
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
Subwoofer Size
“SUB-W”>“SIZE”
2 Select the car type
Turn the [AUD] knob and push the center when
the desired item is displayed.
1 Enter Speaker Setting mode
Press [ ] 1 sec., and select “DSP” > “SETUP” >
“SPEAKER”.
3 Exit Cabin select mode
Press the [ ] button.
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
⁄
•
You can compensate the distances in more details by
using <DTA setting> (page 29) function.
2 Select the speaker you want to set
Turn the [AUD] knob and push the center.
“FRONT”/ “REAR”/ “SUB-W”
3 Select the item you want to set
Turn the [AUD] knob and push the center.
4 Set the value
Turn the [AUD] knob and push the center when
the desired item is displayed.
5 Exit Speaker Setting mode
Press the [ ] button twice.
|
28 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
X’Over Setting
DTA (Digital Time Alignment) Setting
You can set a X’Over value for the speakers;
Adjusting fine tuning of the speaker position
compensation value specified at <Cabin selection>
(page 28).
Setting item
Range
Front High Pass Filter
“FRONT”>“FC”
“THRU”(Through)/ 30/ 40 / 50/
60/ 70/ 80/ 90/ 100/ 120/ 150/
180/ 220/ 250 Hz
1 Enter DTA setting mode
Press [ ] 1 sec., and select “DSP” > “SETUP” >
“DTA”.
Rear High Pass Filter
“REAR”>“FC”
Front High Pass Slope
“FRONT”>“SLOPE”
Rear High Pass Slope
“REAR”>“SLOPE”
Subwoofer Low Pass Filter
“SUB-W”>“FC”
-6/ -12/ -18/ -24 dB/Oct.
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/
120/ 150/ 180/ 220/ 250 Hz/
“THRU”(Through)
2 Select the speaker you want to set
Turn the [AUD] knob and push the center.
“FRONT” (Front speaker)/ “REAR” (Rear speaker)/
“SUB-W” (Subwoofer )
Subwoofer Low Pass Slope
“SUB-W”>“SLOPE”
Subwoofer Phase
-6/ -12/ -18/ -24 dB/Oct.
REVERSE (180°)/ NORMAL (0°)
3 Set the compensation value of the speaker
position
“SUB-W”>“PHASE”
Turn the [AUD] knob and push the center when
the desired value is displayed.
Adjust between 0 and 14.44 feet.
✍ Refer to <Appendix> (page 34) on how to set
the compensation value.
1 Enter X’Over setting mode
Press [ ] 1 sec., and select “DSP” > “SETUP” >
“X’OVER”.
Press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
4 Exit DTA setting mode
Press the [ ] button.
2 Select the speaker you want to set
Turn the [AUD] knob and push the center.
“FRONT”/ “REAR”/ “SUB-W”
3 Select the item you want to set
Turn the [AUD] knob and push the center.
4 Set the X’Over value
Turn the [AUD] knob and push the center when
the desired value is displayed.
5 Exit X’Over setting mode
Press the [ ] button twice.
English
|
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Audio Preset Memory
Audio Preset Recall
Registering the value setup by Sound Control.
Recalling the sound setup registered by <Audio
Preset Memory> (page 30).
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
1 Select the source
Press the [SRC] button.
- Cabin selection (page 28)
- Speaker Setting (page 28)
2 Enter Audio Preset Recall mode
Press [ ] 1 sec., and select “DSP” > “PRESET”>
“RECALL”.
- DTA (Digital Time Alignment) setting (page 29)
- X’Over setting (page 29)
- Preset Equalizer Select (page 26)
- Manual Equalizer Control (page 27)
- Position Control (page 27)
Press the [AUD] knob for at least 1 second.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
3 Select the number to recall in the memory
Turn the [AUD] knob to select number, and then
press the [AUD] knob.
2 Enter Audio Preset Memory mode (Other than
Standby mode)
Press [ ] 1 sec., and select “DSP” > “PRESET” >
“MEMORY”.
Press the [AUD] knob for at least 1 second.
“USER1” – “USER6”
4 Recall the Audio Preset
Turn the [AUD] knob to select “YES”, and then
press the [AUD] knob.
•
For how to select Function Control items, refer to
<Function Control> (page 10).
“COMPLETE” is displayed.
3 Select the number to put in the memory
Turn the [AUD] knob to select number, and then
press the [AUD] knob.
5 Exit Function Control mode
Press the [ ] button for at least 1 second.
“USER1” – “USER6”
⁄
•
The User memory of <Preset Equalizer Select> (page 26)
is changed to the value which was recalled.
The source tone memory item of <Preset Equalizer
Select> (page 26) is changed to the value which was
recalled by the selected source.
4 Put the Audio Preset in the memory
Turn the [AUD] knob to select “YES”, and then
press the [AUD] knob.
•
“COMPLETE” is displayed.
5 Exit Function Control mode
Press the [ ] button for at least 1 second.
⁄
•
•
Register 6 pairs of Audio Preset Memory.
“USER1”: When you press the Reset, all the sources will
be the setting value which is registered.
“USER1”, “USER2”:
•
•
The memory cannot be erased by the Reset button.
This function cannot be registered when the iPod
Equalizer set in <Equalizer Control> (page 26).
|
30 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Radio Tuner Control (Optional)
Basic Operation
Category and Channel Search
Selecting the channel and category you want to
receive.
Selecting Satellite Radio source
Press the [SRC] button.
Select the “SAT”/ “SIRIUS”/ “XM” display.
1 Enter Category and Channel Search mode
Press the [ ] button.
⁄
•
You need to register to the service provider to receive
the service by Satellite Radio. Consult the service
provider if “CALL … TO SUBSCRIBE” appears.
The radio may take a little time to start receiving after
you select the Satellite Radio source.
2 Select the Category
Turn the [AUD] knob, or press the [FM+]/ [AM–]
button.
•
•
3 Select the Channel
If the signal reception fails, “ACQUIRING SIGNAL”/ “NO
SIGNAL” appears.
Press the [4] or [¢] button.
Cancelling Category and Channel Search mode
Press the [ ] button.
Switching Seek Mode
Press [ ] 1 sec., and select “MENU” >
“CHANNEL”/ “PRESET”.
⁄
•
You cannot Channel search until the category
information is acquired.
Press the [4] or [¢] button.
Display
Operation
“CHANNEL”
“PRESET”
Normal manual seeking control.
Search in order of the channels in the Preset memory.
Function of remote control
•
For how to select Function Control items, refer to
<Function Control> (page 11).
Direct Access Tuning
Entering the channel and tuning.
Selecting the channel
Press the [4] or [¢] button.
1 Set the remote controller mode switch to “AUD”
mode
Selecting the Preset Band
Press the [FM+] button.
Each time you press the button, the preset band
alternates between the SR1, SR2, SR3 and SR4.
2 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Channel Scan
3 Enter the channel
Press the [FM+] button for at least 2 seconds.
Pressing this button for 2 seconds or longer allows
you to check individual channel for 10 seconds
each. Pressing this button again for 2 seconds or
longer allows you to exit this mode.
Press the number buttons.
4 Do Channel Search
Press the [4] or [¢] button.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
Preset Memory
Press the desired [1] — [6] button for at least 2
seconds.
⁄
•
If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
If you cannot receive any signal in the input Channel due
to bad conditions on radio wave or other such problems,
“ACQUIRING SIGNAL”/ “NO SIGNAL” appears.
Preset Tuning
Press the desired [1] — [6] button.
•
English
|
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations of Remote Control
Dual Zone Control
SRC
OSD
SRC
TOP MENU
AUDIO
MENU
SETUP
RETURN
ZOOM
Select sub source of Dual zone system: [2 ZONE]
SUBTITLE
ANGLE
AUDIO
ꢃꢄ
Rear channel volume control: [R.VOL]
ꢃꢄ
ꢅ
AUD
U
U
O
AUD
U
U
In Tuner/HD Radio Source (AUD mode)
ENTER
DVD
DVD
O
O
Band select: [FM+]/[AM–]
Station select: [4]/[¢]
Recall preset stations: [1] — [6]
ꢀ/D
FM+/AM–
VOL
O
VOL
2 ZONE
2ZONE
1
2ABC 3DEF
ꢀ
R.VOL
ꢁ
4GHI 5JKL 6MNO
0 — 9
7PQRS 8TUV 9WXYZ
R.VOL
ATT
In DVD/USB/iPod Source (DVD mode)
DIRECT
ATT
0
(page 18)
Refer to <Disc/ USB Operations of remote control>
(page 16).
Refer to <iPod Operations of remote control> (page
20).
Remote Controller Mode Switch
In Satellite Radio Tuner Source (AUD
mode)
The functions operated from the remote controller
differ depending on the position of the mode switch.
AUD mode: [AUD]
Switch to this mode when controlling a selected
source or tuner source, etc.
Preset band select: [FM+]
Channel select: [4]/[¢]
Recall preset channels: [1] — [6]
DVD mode: [DVD]
Switch to this mode when playing DVDs or USB etc.
with the player integrated in this unit.
⁄
About [
⁄
]
•
Switch the mode switch to AUD or DVD position. With the
mode switch in the middle, the remote controller cannot
operate.
This button is used when Bluetooth HANDS FREE
BOX is connected. For more information, refer to the
instruction manual of Bluetooth HANDS FREE BOX.
General Control
Loading and Replacing battery
Use two “AAA”/“R03”-size batteries.
Volume control: [VOL]
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
Source select: [SRC]
Volume reduce: [ATT]
When the button is pressed again, the volume returns
to the previous level.
In Audio Control (AUD mode)
Audio item select: [AUDIO]
Adjust the Audio item: [VOL]
⁄
2CAUTION
•
Do not leave the battery near fire or under direct
sunlight. A fire, explosion or excessive heat generation
may result.
•
Refer to <Audio Control> (page 26) for the operation
method, such as the procedures for Audio control and
others operations.
•
Do not set the remote control in hot places such as on
the dashboard.
|
32 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
About Satellite Radio tuner (Optional)
This unit supports Satellite Radio tuners which are
released by SIRIUS and XM.
Displays of KCA-BT100 Instruction Actual displays on this unit
Manual
“DISCONCT”
“CONNECT”
“PHN-DEL”
“P-STATUS”
“BT-CON Y”
“BT-CON N”
“HF D-CON”
“HF CON”
“DVC-DEL”
“D-STATUS”
“HF-CON Y”
“HF-CON N”
Refer to the instruction manual of Satellite radio tuner.
About HD Radio Reception (Optional)
When you connect an HD Radio tuner, Tuner features
of the unit are disabled and changed to HD Radio
tuner features.
With the HD Radio tuner, you can use the similar
functions of Tuner features. Refer to Tuner features for
how to use the functions.
Function Glossary
•
“AUTO1”, “AUTO2”, “MANUAL” (Tuning mode
select)
Select a tuning mode of the radio.
For operating KCA-BT200 (Optional)
Tuning mode
Display Operation
For operation refer to Model-A-1 in the Instruction
Manual of KCA-BT200, and the table below. The
[AUTO]/[TI] button should be replaced with [SRC]
button for <Answering the Waiting Call after
Terminating>.
Auto seek
“AUTO1” Automatic search for a station.
Preset station seek “AUTO2” Search in order of the stations in the
Preset memory.
Manual
“MANUAL” Normal manual tuning control.
Set the remote controller mode switch to “AUD” mode
before starting operation.
•
“AVIN” (Audio/ visual input)
When this is set to ON, AV input source can be
selected.
Notation used in the KCA-BT200 Operation
Instruction Manual
ON1: Allows AV input source to be selected. Use
this setting when the built-in AV IN terminal is
connected to the external equipment all the
time.
ON2: Activates the attenuator function when
turning on the power with AV input source
selected. Cancel the attenuator function
by turning the volume knob clockwise
when listening to the audio of the external
equipment.
[38] button
Control knob
[AUD] knob*1
[AUD] knob
[AUTO]/[TI] button
[DISP] button
Control knob towards up or down
Control knob towards left or right
[FM+] or [AM–] button
[4] or [¢] button
*1 Use the [38] button for the operation of <Switching to the
Private Mode>.
OFF: Disable AV input source selection. Use this
setting when the built-in AV IN terminal is not
used.
“CHANNEL”, “PRESET” (Seek mode Setting)
Sets the seek mode of the satellite Radio.
CHANNEL: Normal manual seeking control.
PRESET: Search in order of the channels in the
Preset memory.
For operating KCA-BT100 (Optional)
To control KCA-BT100, operate as follows;
To make setting for <Selecting the Dialing Mode>,
select <Function Control> (page 10). Pressing the
[AUD] knob for at least 1 second after selecting
the "D.MODE" item allows you to enter the dialing
method selection mode. To exit from dialing method
selection mode, press Search button.
To make <Disconnecting a Call>, <Clearing the
Disconnection Message>, and <Rejecting an
Incoming call>, press [DISP] button for at least 1
second.
Set the remote controller mode switch to “AUD” mode
before starting operation.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
•
•
DTA (Digital Time Alignment)
Make fine adjustment of the delay time of the
speaker output specified at <Cabin selection>
(page 28) to have a more suitable environment for
your vehicle.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
Next page 3
English
|
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
+3.4feet
1.6feet
2.5feet
5feet
+2.5feet
+0feet
•
•
“HIGHWAY” (Highway sound)
Increases the volume of faintest sound being lost
by road noises to make the sound more audible.
Additionally, it accentuates bass sound being
lost by road noises to make the bass sound more
dynamic.
“ICON”
Sets the Graphics mode of the display during
normal playback condition.
ON1: Turns on.
ON2: Displays an animation.
OFF: Turns off.
•
•
“SWPRE” (Switching Preout)
Switches the preout between rear output (“R”),
subwoofer output (“SW”), and DVD/USB/AV input
source output (“AV”).
“ZONE2” (Dual Zone)
Set the destination (front speaker “F” or rear speaker
“R”) of the sub source (DVD/USB/AV input) when
the Dual Zone function is turned on.
|
34 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Language code list
Code
Language
English
Spanish
French
German
Italian
Dutch
Swedish
Danish
Code
HE
HI
HR
HU
HY
IA
IE
IK
ID
IS
Language
Hebrew
Hindi
Code
RO
RW
SA
SD
SG
SH
SI
Language
Romanian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
ENGLISH
SPANISH
FRENCH
GERMAN
ITALIAN
DUTCH
SWEDISH
DANISH
RUSSIAN
CHINESE
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Luxembourgish
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
SK
SL
Russian
Chinese
Slovenian
Samoan
Shona
SM
SN
SO
SQ
SR
SS
PORTUGUESE Portuguese
JV
JAPANESE
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GLI
GN
GU
HA
Japanese
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LB
LN
LO
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
ST
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Malay
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Punjabi
Polish
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
PL
PS
QU
RM
RN
Pashto, Pushto
Quechua
Rhaeto-Romance
Kirundi
English
|
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Installation Procedure
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Accessories
1
2
3
4
5
•
..........1
..........2
..........1
..........4
..........4
•
•
•
•
Installation Procedure
•
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
•
•
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
About CD players/disc changers connected
to this unit
If the CD player/ disc changer has the “O-N” switch, set
it to the “N” position.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
8. Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
Install this unit in the console of your vehicle. Do not touch
the metal part of this unit during and shortly after the use
of the unit. Metal part such as the heat sink and enclosure
become hot.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
•
•
|
36 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
AV input
For the sake of safety, be sure to
connect the parking sensor.
Use of the optional cable CA-C3AV
is recommended for connecting an
external player.
Parking sensor wire (Light Green)
Connect to the vehicle’s
PRK SW
⁄
Parking sensor wire
Junction cable
(Light Green)
parking brake detection
switch harness.
USB connector
(Accessory3)
Visual output (Yellow)
FM/AM antenna input
Front output
Front side
L
R
Rear output/ Sub Woofer output/
AV output (audio)
Do not connect.
Fuse (10A)
Wiring harness
(Accessory1)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant instruction manuals.
⁄
White
White/Black
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Power control/Motor antenna control wire
(Blue/White)
Connect either to the power control terminal when using the optional
power amplifier, or to the antenna control terminal in the vehicle.
P.CONT
TEL mute wire (Brown)
Connect to the terminal that is grounded when either the telephone rings
or during conversation.
MUTE
To connect the Kenwood navigation system, consult your navigation
⁄
manual.
Motor antenna control wire (Blue)
Depending on what antenna you are using, connect either to the control
terminal of the motor antenna, or to the power terminal for the booster
amplifier of the film or short pole-type antenna.
ANT.
CONT
Car fuse box
ACC
Ignition key switch
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
(Main fuse)
Ground wire (Black) - (To car chassis)
Battery
English
|
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Removing the Unit
Non-Japanese cars
Removing the hard rubber frame
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Accessory2
⁄
Removal tool
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2 When the upper level is removed, remove the
lower two locations.
⁄
Japanese cars
•
The frame can be removed from the bottom side in the
same manner.
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
Removing the Unit
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Insert the two removal tools deeply into the slots
T
N
on each side, as shown.
T/N
3 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
T
N
T: Toyota cars
N: Nissan cars
Accessory2
8 mm
MAX.
8mm
MAX.
4
5
ø5mm
ø5mm
Accessory4...for Nissan car
Accessory5...for Toyota car
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
4 Pull the unit all the way out with your hands, being
careful not to drop it.
|
38 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• Cannot set up the low pass filter.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• <Subwoofer output> of <Basic Operation> (page 8)
is not set to On.
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
• Preout is not set to subwoofer. ☞ “MENU” > “SWPRE”
of <Function Control> (page 11)
☞
Pull the antenna out all the way.
• The Dual zone function is enabled.
☞ <Audio Setup> (page 26)
Disc source
? The specified disc does not play, but another one
plays instead.
!
• Cannot set up the equalizer.
✔
✔
The specified disc is quite dirty.
• Cannot set up the crossover network.
• Cannot set up Digital Time Alignment.
• Cannot select the “CONTROL” in “DSP”.
• Cannot select the “SETUP” in “DSP”.
• The Dual zone function is enabled.
☞ <Audio Setup> (page 26)
☞
Clean the disc, referring to the disc cleaning of
the section on <Handling discs> (page 3).
The disc is loaded in a different slot from that
specified.
☞
Eject the disc magazine and check the number
for the specified disc.
• The DSP function is disabled. ☞ “DSP” > “DSP SET” of
<Function Control> (page 12)
• In the speaker select option, None is selected for
✔
The disc is severely scratched.
Try another disc instead.
☞
the rear speakers. ☞ <Speaker Setting> (page 28)
Audio file source
? The sound skips when an Audio file is being
!
!
Cannot set up the Dual zone.
The AV output function is enabled.
☞ <Audio Setup> (page 26)
played.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the disc cleaning of
the section on <Handling discs> (page 3).
• Cannot set up the AV output.
• Cannot select the “SWPRE” in “MENU”.
The Dual zone function is enabled.
☞ <Audio Setup> (page 26)
The recording condition is bad.
Record the media again or use another media.
☞
!
!
• Cannot register a security code.
• Cannot set up Display.
<Demonstration mode Setting> (page 7) is not
turned off.
• Cannot switch to DVD or USB source.
• The Dual zone function is set to DVD or USB.
☞ <Audio Setup> (page 26)
• AV output source is set to USB or DVD.
☞ <Audio Setup> (page 26)
English
|
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
NA DVICE:
• An unsupported USB device is connected.
• Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 4) for information on supported
iPods.
The messages shown below display your
systems condition.
TOC ERR:
• The disc is quite dirty. The disc is upside-
down. The disc is scratched a lot.
• No disc has been loaded in the disc
magazine.
NO MUSIC/E-15:
USB ERR:
• The connected USB device contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
E-05:
E-77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
“E-77” code does not disappear, consult
your nearest service center.
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, turn off the unit,
wait for about 10 seconds, and then turn
on the unit again. If the same display is
repeated, use another USB device.
E-99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the “E-99”
code does not disappear, consult your
nearest service center.
iPod ERR:
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
MEC ERR:
IN (Blink):
The unit is malfunctioning for some reason.
➪ Press the [0] button on the unit. If the
error message does not disappear when
you eject the disc and insert it again,
consult your nearest service center.
REG ERR:
The disc you wanted to play has a region
code that cannot be played with this unit.
The DVD player section is not operating
properly.
PARK OFF:
Source for displaying video is selected while
car is traveling.
➪ Video will be displayed when the car is
stopped and the parking brake has been
engaged.
➪ Press the [DISP] button for at least 1
second. The display of this unit can be
temporarily hidden.
➪ Reinsert the disc. If the disc cannot be
ejected or the display continues to flash
even when the disc has been properly
reinserted, please switch off the power
and consult your nearest service center.
PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the “PROTECT” code does not disappear,
consult your nearest service center.
READING:
The unit is reading the data on the media.
NA FILE:
An Audio file is played with a format that this
unit can’t support.
COPY PRO:
READ ERR:
A copy-protected file is played.
The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
NO DVICE:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
|
40 KDV-415U/ KDV-MP5042U
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
WMA
Bit Rate : 32kbps - 320kbps
Sampling Frequency : 22.05k/32k/44.1k/48kHz
WAV (Linear PCM)
Quantization Bit Rate : 16 bit
FM tuner section
Frequency range
200 kHz space
: 87.9 MHz – 107.9 MHz
50 kHz space (KDV-MP5042U)
: 87.5 MHz – 108.0 MHz
Sampling Frequency : 44.1kHz
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
USB Interface
USB Standard
: USB1.1/ 2.0
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Data Transfer Rate
: Maximum 12 Mbps
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Compatible Device
: Mass storage class
Signal to Noise ratio (MONO)
: 70 dB
Maximum Supply current
: 500 mA
Selectivity ( 400 kHz)
: ≥ 80 dB
File System
: FAT16/ 32
Stereo separation (1 kHz)
: 40 dB
Playable Video/Audio Format
: MPEG1/ MPEG2/ DivX (Maximum 2 Mbps)/
MP3/ WMA/ WAV (Linear PCM)
AM tuner section
Frequency range (10 kHz space)
: 530 kHz – 1700 kHz
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
Audio/ Video section
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
DVD player section
Signal Detection System
: Non-contact optical pickup (semiconductor
laser)
Wow & Flutter
: Below Measurable Limit
Frequency response
Sampling frequency; 96 kHz : 16 – 22,000 Hz
Sampling frequency; 48 kHz : 16 – 22,000 Hz
Sampling frequency; 44.1 kHz : 16 – 20,000 Hz
Signal to Noise ratio (1 kHz)
: 95 dB
Dynamic range
Sampling frequency; 96 kHz : 100 dB
Speaker Impedance
: 4 – 8 Ω
Tone action
Frequency (BAND1 – 5): 60/ 250/ 1k/ 4k/ 16k Hz
Gain : 9 dB
Video terminal
Output/ Input level : 1 Vp-p (75 Ω)
Color System : NTSC
Audio terminal
Output level / Load (DVD) : 2500 mV/10 kΩ
Output impedance : ≤ 600 Ω
Input Maximum Voltage : 1200 mV
Input Impedance : 10 kΩ
Sampling frequency; 48/ 44.1 kHz : 90 dB
DivX
General
Max. Resolution : 720 x 480 pixels (30fps)/
720 x 576 pixels (25fps)
Operating voltage (10.5 – 16V allowable)
: 14.4 V
Maximum Current consumption
: 10 A
Audio Bit Rate : 32kbps - 320kbps
Audio Sampling Frequency :
MPEG-1:32k/44.1k/48kHz
MPEG-2:16k/22.05/24kHz
Installation Size (W x H x D)
: 182 x 53 x 159 mm
MPEG video
Max. Resolution : 720 x 480 pixels (30fps)/
720 x 576 pixels (25fps)
7-3/16 x 2-1/16 x 6-1/4 inch
Weight
: 3.1 lbs (1.4 kg)
Audio Bit Rate : 32kbps - 320kbps
Audio Sampling Frequency : 32k/44.1k/48kHz
MP3
Bit Rate : 32kbps - 320kbps
Sampling Frequency : MPEG-1:32k/44.1k/48kHz
MPEG-2:16k/22.05/24kHz
Specifications subject to change without notice.
English
|
41
Download from Www.Somanuals.com. All Manuals Search And Download.
KDV-415U
KDV-MP5042U
The marking of products using lasers
(Except for some areas)
2CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
In compliance with Federal Regulations, following are
reproductions of labels on, or inside the product relating to
laser product safety.
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
Location : Top Panel
FCC WARNING
This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause
harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose
the authority to operate this equipment if an unauthorized
change or modification is made.
HD Radio™ Technology Manufactured Under License From
iBiquity Digital Corp. U.S. and Foreign Patents. HD Radio™
and the HD Radio Ready logos are proprietary trademarks
of iBiquity Digital Corp.
NOTE
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
iPhone is a trademark of Apple Inc.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed and
used in accordance with the instructions. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
“Made for iPod”means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
“Works with iPhone”means that an electronic accessory
has been designed to connect specifically to iPhone
and has been certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
DivX® is a registered trademarks of DivX, Inc., and is used
under license.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
is a trademark of DVD Format/Logo Licensing
Corporation registered in the U.S., Japan and other
countries.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Download from Www.Somanuals.com. All Manuals Search And Download.
|