Operating Instructions and Parts Manual
Dust Collector
DC-1200 Series Dust Collectors
DC-1200BK
DC-1200CK
WALTER MEIER (Manufacturing), Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Ph.: 800-274-6848
Part No. M-710700
Revision A1 03/2010
Copyright © 2010 Walter Meier (Manufacturing), Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service.................................................................................................................................2
Table of Contents ......................................................................................................................................3
Warnings...................................................................................................................................................4
Introduction ...............................................................................................................................................6
Specifications ............................................................................................................................................6
Ordering Replacement Parts.......................................................................................................................6
Unpacking.................................................................................................................................................7
Shipping Content .......................................................................................................................................7
Base Units .............................................................................................................................................7
Canister Filter Kit....................................................................................................................................8
Bag Filter Kit ..........................................................................................................................................8
Base Unit Assembly...................................................................................................................................9
Base......................................................................................................................................................9
Motor and Fan Assembly ........................................................................................................................9
Connector Housing...............................................................................................................................10
Hose....................................................................................................................................................10
Filter Bag Kit Assembly ............................................................................................................................11
Filter Bag Installation ............................................................................................................................11
Collector Bag Installation.......................................................................................................................11
Canister Kit Assembly ..............................................................................................................................12
Canister Filter.......................................................................................................................................12
Collector Bag .......................................................................................................................................12
Electrical Connections..............................................................................................................................13
Turning the Machine On & Off ..................................................................................................................13
All Models ............................................................................................................................................13
Remote Control (optional) .....................................................................................................................13
Turning the DC-RC230 On & Off ...........................................................................................................13
Changing Operating Frequency.............................................................................................................14
Installing the DC-RC Remote Power Control ..........................................................................................14
Maintenance............................................................................................................................................15
Cleaning the Filter Bag - DC-1200BK and DC-1200-3BK.........................................................................15
Removing the Collector Bag – DC-1200BK and DC-1200-3BK ................................................................15
Cleaning the Canister Filter – DC-1200CK and DC-1200-3CK .................................................................15
Removing the Collector Bag – DC-1200CK and DC-1200-3CK................................................................15
Motor...................................................................................................................................................15
Connecting the Dust Collector to a Machine ...........................................................................................15
Grounding the Dust Collection System...................................................................................................15
Parts Breakdown .....................................................................................................................................17
Canister Filter Assembly .......................................................................................................................18
Filter Bag Assembly..............................................................................................................................19
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
1. Read and understand the entire owner's manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of
these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a dust collector, do not use until proper training
and knowledge have been obtained.
5. Do not use this dust collector for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that
may result from that use.
6. Always wear approved safety glasses/face shields while using this dust collector. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this dust collector, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face
or dust masks that are specifically designed to filter out microscopic particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches
are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes,
use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly repaired or
replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings,
metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with
any part of the dust collector.
23. Use recommended accessories; improper accessories may be hazardous.
24. Maintain tools with care. Follow instructions for lubricating and changing accessories.
25. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not
use your hands.
26. Do not stand on the machine. Serious injury could occur if the machine tips over.
27. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
28. Remove loose items and unnecessary work pieces from the area before starting the machine.
29. Never place hands near the inlet of the machine.
30. Always make certain machine is off and unplugged when making any connections to the inlet.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by JET covering the safe operation and maintenance procedures for model
DC-1200 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. This machine has been designed and
constructed to provide years of trouble free operation if used in accordance to instructions set forth in this
manual. If there are any questions or comments, please contact either your local supplier or Walter Meier
(Manufacturing) Inc.
Specifications
Base Machines
Models.................................................. DC-1200M................................................................DC-1200M-3
Stock Number ............................................ 710700.........................................................................710720
Blower Wheel Diameter ................................................................................................................... 12”
Sound Rating at 3 feet.............................................................................................................70-80 db
Hose Diameter ...........................................................................................................................4" & 6”
Air Flow (CFM).............................................................................................................................1,200
Velocity at 4” (FPM)....................................................................................................................13,745
Static Pressure (inch of water).......................................................................................................11.44
Overall Dimensions .................................................................................................37"L x 28"W x 79"H
Motor (TEFC)...............................2 HP, 1Ph 230V Only....................2 HP, 3Ph 230/460V, Prewired 230V
Net Weight (approx.) ................................................................................................................ 140 lbs.
Bag Filter Kit
Stock Number .........................................................................................................................708636F
Bag Diameter.................................................................................................................................. 20"
Filter Efficiency................................................................................................................................30 micron
Collector Bag Capacity (cu. ft.)......................................................................................................... 5.6
Canister Filter Kit
Stock Number .........................................................................................................................708639B
Bag Diameter.................................................................................................................................. 20"
Filter Efficiency..................................................................................................................................2 micron
Collector Bag Capacity (cu. ft.)......................................................................................................... 5.6
Remote Control Unit (Optional)
Stock Number (main unit and remote control switch) (230V only)............................................... 708636D
Stock Number (Remote Control Switch only).............................................................................708636T
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier reserves the right to change specifications at any time and without prior
notice, without incurring obligations.
Ordering Replacement Parts
Replacement parts are listed in the back of this manual. To order parts or reach our service department, call
the Model Number and Serial Number of your machine available when you call will allow us to serve you
quickly and accurately.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Shipping Content
The table below lists the shipping cartons that are
included with the various models of the DC-1200
Dust Collector.
Base Unit
s
(SN 710700 and 710720)
1 – Housing (A)
1. Locate your particular model and verify that you
have received the all the correct cartons.
2 – Hose Clamps (B)
1 – Hose (C)
2. Check contents of each carton against the ship-
ping content listings on this and the following
page.
1 – Impeller (Motor/Fan Assembly) (D)
1 – Inlet Port (E)
1 – Impeller Cover (F)
3 – Support Legs (G)
1 – Base (H)
3. Report any damage to your distributor.
4. Do not discard any shipping material until after
the dust collector has been assembled and is
running properly.
4 – Casters (J)
1 – Owner's Manual (not shown)
1 – Warranty Card
1 – Hardware Bag (SN DC1200-HP)
DC-1200BK
DC-1200CK
DC-1200-3BK
DC-1200-3CK
x
x
x
x
x
x
x
x
Table – DC-1200 Dust Collector cartons
Hardware Bag for Base Unit
(SN DC1100-HP)
16 – M8 x 16 Hex Cap Screws (K)
22 – M8 Flat Washers (L)
08 – M6 x 12 Pan Head Flange Screws (M)
06 – M8 Hex Nuts (N)
Base Machine Shipping Contents
Assembly Hardware
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter Kit
(SN 708639B)
Bag Filter Kit
(SN 708636F)
1 – Handle (O)
1 – Upper Bag Hanger (Y)
1 – Hanger Bracket (Z)
1 – Collector Bag (X)
1 – Filter Bag (W)
1 – Canister Filter (P)
1 – Snap Ring (Q)
5 – Collector Bags (R)
1 – Canister Filter Hardware Bag (SN DC1100-CHP)
Contains:
1 – Retainer Strap (AA)
(2) M10 Hex Nuts (S)
(2) M10 Flat Washers (T)
(1) M10 Lock Washer (U)
(4) Knobs (V)
Filter Bag Kit Contents
Canister Filter Kit Contents
Canister Filter Hardware
(SN DC1100-CHP)
Canister Filter Hardware
Read and understand the entire contents of this manual before attempting set-up or
operation! Failure to comply may cause serious injury.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Unit Assembly
Base
1. Install four casters to the under side of the base as
pictured in Fig. 2.
Referring to Figure 1:
2. Thread the hex nut (B) onto the caster shaft. Then
slide the lock washer (A) over the caster shaft.
Thread the caster shaft into the threaded hole on
the underside of the base, turn until snug. Tighten
the nut (B) against the base with a 14mm wrench.
This will give the caster proper clearance.
Figure 1
Motor and Fan Assembly
Referring to Figure 2:
3. Place the base (C) with casters on the ground.
Attach the motor and fan assembly (A) to the base
using four each M8 x 16 hex cap screws, and M8
flat washers (B). Tighten with a 13mm wrench.
The dust collector must not be
connected to the power source during assembly.
Failure to comply may result in serious injury!
Figure 2
Referring to Figure 3:
4. Attach impeller cover (A) to fan housing (D) using
eight M6 x 12 pan head screws (B). Press the inlet
ports (C) onto the inlet guard until it snaps into
place.
To reduce the risk of injury from
moving parts, always keep inlet port covered with
the caps provided, if they are not connected to a
hose. Failure to comply may result in serious
injury!
Figure 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Housing
5. Attach three support legs (A, Fig. 4) to the base
using six M8 x 16 hex cap bolts and six M8 flat
washers (B, Fig. 4). Hand-tighten only at this time.
Figure 4
6. Install the housing (A, Fig. 5) to two support
legs (B, Fig. 5) using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts (C,
Fig. 5). Be sure hose opening faces fan housing.
Note: For models DC-1200BK or DC-1200-3BK
only – Before attaching third support bracket place
the hanger bracket (D, Fig.5) between the support
bracket and the housing.
7. Tighten all nuts and bolts at this time with a 13mm
wrench.
Figure 5
Hose
Referring to Figure 6:
8. Attach the hose (B) between the fan housing (A)
and the impeller housing (D) with two clamps (C).
Tighten the clamps to secure the hose.
This completes the Base Unit assembly. If you
purchased the DC-1200BK or DC-1200-3BK Dust
Collector (filter bag version), continue on the following
page. If you purchased the DC-1200CK or DC-1200-
3CK Dust Collector (canister filter version), proceed to
Canister Kit Assembly section on page 12.
Figure 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Filter Bag Kit Assembly
If you purchased Model DC-1200BK or DC-1200-3BK
Dust Collector, this section describes the assembly
and installation of the contents of the Filter Bag Kit
(SN 708636F).
Filter Bag Installation
Referring to Figure 7:
1. Place the hanger (A) on the hanger bracket (B).
2. Slide the filter bag loop (C) over the hanger hook.
3. Feed the retainer strap (D) through the loops on
the filter bag (E) and fasten to the collector
housing (F).
Figure 7
Collector Bag Installation
Referring to Figure 8:
4. Insert the ring of the collector bag (A) at an angle
into the housing (B) through the opening at the
bottom. Pull down on the bag to make sure it
“seats” in the housing.
5. Position the plastic window in front so that you can
easily see when the collector bag is full.
After completing the filter bag and collector bag
installation, proceed to Electrical Connections.
Figure 8
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Kit Assembly
If you purchased Model DC-1200CK or DC-1200-3CK
Dust Collector, this section describes the assembly
and installation of the contents of the Canister Kit
(SN 708636F).
Canister Filter
1. Mount the handle onto the canister filter with two
M10 hex nuts, two M10 flat washers, and a M10
lock washer (Figure 9).
2. Mount the canister filter on top of the collector
housing (A, Fig. 5) and tighten the knobs on the
canister filter (Figure 9).
Figure 9
Collector Bag
3. Place the ring over the top of the plastic bag and
fold over the bag approximately three inches,
Figure 10.
Figure 10
4. Insert the snap ring (A, Fig. 11) of the collector
bag into the bottom of the housing at an angle.
5. Pull down on the ring to make sure it “seats” in the
housing.
Note: make sure the snap ring “snaps” into place
in the housing, and also that the plastic bag hangs
down approximately 3” so that there are no air
leaks.
Figure 11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Dust Collector RF Remote
All electrical connections must
Power Control (optional)
be done by a qualified electri-
cian. All adjustments or repairs must be done
with the dust collector disconnected from the
power source, unplugged. Failure to comply may
result in serious injury!
The DC-RC230 Remote Power Control (Figure 13)
should be used for activating Dust Collection units
powered by 230V only up to 3HP, 1 Phase. The DC-
RC230 Remote Power Control unit is rated at 230V,
Single Phase only. Use an outlet rated at least
20amps. The circuit for the device being controlled by
the DC-RC230 should also be protected by at least a
20 amp circuit breaker or fuse.
The DC-1200BK/CK dust collectors are rated at 230V
Only. The DC-1200 is not supplied with a plug. Use a
plug and outlet rated at least 20 amps. The circuit for
the machine should also be protected by at least a 20
amp circuit breaker or fuse.
Before hooking up to the power source, make sure
that the switch is initially in the off position on both
the dust collector and remote control unit (Figure 12).
The DC-1200-3BK and DC-1200-3CK are rated at 3
Phase 230V/460V, Prewired 230V. If you want to
run these on 460V refer to the wiring diagram found
on the inside of the switch box cover.
Turning the DC-RC230 On & Off
This machine is intended for
indoor use only.
Keep in mind that a circuit being used by other
machines, tools, lights, heaters, etc. at the same time
will add to the electrical load. A dedicated circuit to
the dust collector will give you the best results since
dust collectors are generally used at the same time
other tools are running.
1. Plug the dust collector into the main unit
(Figure 13) and plug the main unit into the power
outlet.
To start a machine or device:
2. Turn the machine itself on.
Turning the Machine On & Off
3. On the main unit place the switch to the ON
position (Figure 12A). The red LED on the main
unit should light up.
This machine is intended for
indoor use only.
4. Press the button on the remote control
transmitter (Figure 13) to turn the machine on.
All Models
Before hooking up to the power source, make sure
that the switch is in the off position.
5. To stop the machine, press the button on the
remote control transmitter again.
Turn the dust collector on by pressing the Start
button mounted next to the motor. Press the Stop
button to turn off the dust collector.
Remote Control (optional)
If you have the DC-1200BK or DC-1200CK, the DC-
RC230 RF Remote Power Control unit is available as
an optional accessory (contact Customer Service by
calling the number on the cover).
Important: The DC-RC230 Remote Power Control
can be used for activating Dust Collection units
powered by 230V only up to 3HP, single phase
only.
Figure 13
Figure 12A
Figure 12B
When the machine is running, it can be stopped by
placing the switch on the main unit in the off position
(Figure 13). To restart, repeat steps 3 and 4.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To mount the DC-RC230 Remote Power Control
(refer to Figure 15):
Changing Operating Frequency
If several devices are controlled by the same type
remote control unit, each remote control unit can be
set to operate at its' own unique operating frequency
as follows:
Note: Mounting hardware is not included and must
be supplied by the machine’s owner or user.
1. Place RC Power Control Unit (A) on the open
clearing of the base (B) of the dust collector near
the motor (C).
Referring to Figure 14:
1. Unplug the DC-RC230 Remote Power Control
2. Using a marker, mark the base through the
mounting holes of the power control units
mounting tabs.
unit.
2. Remove the back covers of the main unit (A) and
remote control switch (B).
3. Drill two holes (D) through the base where
marked.
3. Locate the DIP switch (C) in each unit.
4. Change the position of the DIP switches in the
main unit (A) to any combination desired as long
as they are not the same as other units that may
be present and located within the radio frequency
range.
4. Insert screws through the tabs and base. Place
washers and hex nuts on the threaded ends of
the screw underneath the base and tighten.
5. Set the DIP switches (C) in the remote control
switch (B) to match the switch settings in the
main unit (A).
6. Replace the back covers to the main unit and
remote control switch.
7. Operate a device as described in Turning the
DC-RC230 On & Off and verify that other devices
using the same type remote control do not turn
on.
Figure 15
Figure 14
Installing the DC-RC Remote Power
Control
The DC-RC230 Remote Power Control unit can be
placed anywhere for convenience and portability if
used to control other machines or it can be mounted
as a permanent part of a machine, such as the DC-
1200 Dust Collector.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Canister Filter – DC-1200CK
and DC-1200-3CK
Maintenance
Never perform maintenance on
this machine before turning switch off and
removing plug from power source. Failure to
comply may cause serious injury!
Never perform maintenance on
this machine before turning switch off and
removing plug from power source. Failure to
comply may cause serious injury!
Clean both the filter and collector bags frequently to
keep the collector's performance at its optimum.
Cleaning the Filter Bag - DC-1200BK and
DC-1200-3BK
To clean the filter, turn the handle a couple of
rotations so the dust falls into the collector bag.
Wearing
a
particle mask or
respirator for protection against fine dust
particles during cleaning is highly recommended.
Removing the Collector Bag –
DC-1200CK and DC-1200-3CK
During first use and after cleaning, the filter bag may
allow some dust to escape. This is normal and will
stop after a short period of time.
Wearing
a
particle mask or
respirator for protection against fine dust
particles during cleaning is highly recommended.
Clean both the filter and collector bags frequently to
keep the collector's performance at its optimum. To
clean:
1. Disconnect the machine from the power source
outlet.
1. Disconnect the machine from the power source.
2. Remove the collector bag by pushing the ring of
the collector bag upwards at an angle and
pulling the bag and snap ring out.
2. Unhook the filter bag from the hanger and shake
the bag so that the majority of the dust falls into
the collector bag.
3. Empty the contents into an appropriate
container.
3. Loosen the retaining strap, and remove the filter
bag from the housing.
To replace the collector bag, refer to the Collector
Bag Installation on page 12.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and re-attach to the
housing using the retainer strap to secure.
Motor
Make frequent inspections of the motor fan and blow
out (with low pressure air hose) or vacuum any
accumulation of foreign material in order to maintain
normal motor ventilation.
Removing the Collector Bag –
DC-1200BK and DC-1200-3BK
1. Disconnect the machine from the power source.
2. Remove the collector bag by pushing the ring of
the collector bag upwards and pulling the bag
out at an angle.
Connecting the Dust Collector to a
Machine
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer vent
hose is not acceptable for this purpose. Contact your
nearest JET distributor for the full line of JET Dust
Collector Hoses and Accessories. Customize your
installation and obtain maximum performance with
JET's dust hoods, hoses, clamps, fittings, and blast
gates.
3. Empty the contents into an appropriate
container.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and insert into the
housing.
To replace the collector bag, refer to Collector Bag
Installation on page 11.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer vent
hose is not acceptable for this purpose. Contact your
nearest JET distributor for the full line of JET Dust
Collector Hoses and Accessories. Customize your
installation and obtain maximum performance with
JET's dust hoods, hoses, clamps, fittings, and blast
gates.
Grounding the Dust Collection System
The dust collection system includes the dust collector
and the hose, or ductwork you use to connect the
tools. The dust collector is grounded though the
ground wire in the cord. The hose or ductwork you
use to connect the tool to the dust collector must also
be grounded. To assist in grounding your system
you can purchase the JET “Dust Collector Grounding
Kit” stock # JW1053 through JET Distributors.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the DC-1200M/DC-1200M-3
Description
Index No. Part No.
Size
Qty
1.............. 411035W................ Impeller Housing.............................................. ..............................................1
2.............. 411026W................ Motor Bracket.................................................. ..............................................1
3.............. 998621................... Strain Relief..................................................... ..............................................1
4.............. MA411003.............. Motor .............................................................. 2 HP, 1Ph...............................1
................ MA411003-3........... Motor .............................................................. 2 HP, 3 Ph..............................1
................ DC1100-50W.......... Motor Fan Cover (not shown) ........................... ..............................................1
................ MF411012.............. Motor Fan (not shown) ..................................... ..............................................1
................ CA003030 .............. Running Capacitor (not shown)......................... 30MFD, 300V .........................1
................ CA020010 .............. Starting Capacitor (not shown).......................... 200MFD, 125V .......................1
5.............. 411051................... Switch Box ...................................................... ..............................................1
6.............. 411053................... Switch Plate .................................................... ..............................................1
7.............. 994542................... Switch............................................................. 1 Ph.......................................1
................ DC1900-23B........... Switch............................................................. 3 Ph.......................................1
8.............. IC420002 ............... Power Cord..................................................... ..............................................1
9.............. 420051................... Motor Packing ................................................. ..............................................1
10............ AB411059 .............. Impeller ........................................................... 12”.........................................1
11............ 411036W................ Inlet Guard ...................................................... ..............................................1
12............ 427028................... Inlet Port ......................................................... 2 @ 4”....................................1
13............ 420203................... Inlet Cap ......................................................... ..............................................2
14............ 430034................... Inlet Flange Packing......................................... ..............................................1
15............ 411041W................ Base ............................................................... ..............................................1
16............ 402036................... Pivoting Caster ................................................ ..............................................4
17............ 420012W................ Housing........................................................... ..............................................1
18............ 402004W................ Support ........................................................... ..............................................3
20............ 411009................... Hose............................................................... 5”x65(CM) ..............................1
21............ 420010................... Ring Clamp ..................................................... 5”...........................................2
31............ ST039304............... Tapping Screw................................................. M3.5x12(AB) ..........................6
32............ KS050525 .............. Key................................................................. 5x5x25 ...................................1
34............ TS-1540061............ Nut.................................................................. M8.......................................10
35............ TS-0561031............ Nut.................................................................. 3/8”-16UNC............................4
36............ SH080402 .............. Hex Head Bolt ................................................. M8x20 L.H..............................1
37............ TS-1490011............ Hex Head Bolt ................................................. M8x12....................................4
38............ TS-1490021............ Hex Head Bolt ................................................. M8x16..................................16
39............ TS-1490041............ Hex Head Bolt ................................................. M8x25....................................4
40............ TS-1554041............ Pan Head Bolt W/Flange .................................. M6x12....................................2
41............ TS-0680031............ Flat Washer..................................................... M8.........................................1
42............ TS-1554041............ Pan Head Bolt W/Flange .................................. M6x12....................................8
43............ TS-0680031............ Flat Washer..................................................... M8.......................................34
44............ TS-0720081............ Spring Washer................................................. M8.........................................8
45............ TS-1551071............ Spring Washer................................................. M10 .......................................4
46............ ST059304............... Tapping Screw................................................. M5x12....................................2
................ DC1200-53............. Grounding Label (not shown)............................ ..............................................1
................ DC1200-54............. Direction Label (not shown) .............................. ..............................................1
................ DC1200A-NP.......... Name Plate (not shown) ................................... ..............................................1
................ DC1100-HP............ Hardware Package (not shown) ........................ ..............................................1
................ DC1200A-CS.......... Centrifugal Switch (not shown).......................... ..............................................1
................ DC1900-53............. Warning Label (not shown) ............................... ..............................................1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter Assembly
Index No. Part No.
Description
Size
Qty
1.............. 331050................... Handle ............................................................ ..............................................1
2.............. TS-1540071............ Hex Nut........................................................... M10 .......................................2
3.............. TS-1550071............ Flat Washer..................................................... M10 .......................................2
4.............. TS-2361101............ Lock Washer ................................................... M10 .......................................1
5.............. BR000052 .............. Rivet ............................................................... 5-2.........................................3
6.............. 331014................... Bracket ........................................................... ..............................................1
7.............. 150623................... Pad................................................................. ..............................................1
8.............. 331051................... Soft Grip Handle .............................................. ..............................................2
9.............. TS-1540041............ Hex Nut........................................................... M6.........................................8
10............ 708739................... Filter ............................................................... ..............................................1
11............ 331052................... Shaft............................................................... ..............................................1
12............ TS-1482041............ Hex Cap Screw................................................ M6X20 ...................................4
13............ TS-2361061............ Lock Washer ................................................... M6.........................................4
14............ TS-1550041............ Flat Washer..................................................... M6.........................................4
15............ 331012................... Scraper ........................................................... ..............................................2
16............ 331017................... Strip................................................................ ..............................................2
17............ 331015................... Press Plate...................................................... ..............................................2
18............ TS-1482021............ Hex Cap Screw................................................ M6x12....................................4
19............ 331037................... Knob............................................................... ..............................................4
20............ 331031................... Pad................................................................. ..............................................1
21............ 331009................... Support ........................................................... ..............................................1
22............ ST049200............... Tapping Screw................................................. M4X8.....................................4
23............ 331038................... Snap Ring ....................................................... ..............................................1
24............ 709563................... Plastic Bag ...................................................... ..............................................5
..................DC1100-CHP...........Canister Hardware Package....................................................................................
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Filter Bag Assembly
Index No. Part No.
Description
Size
Qty
1.............. 708698................... Filter Bag ........................................................ 30 Micron Bag ........................1
................ 708702................... Filter Bag (optional).......................................... 5 Micon Bag ...........................1
2.............. AB410012 .............. Retainer Strap ................................................. ..............................................1
3.............. 708699A................. Collection Bag ................................................ ..............................................1
4.............. 430038................... Hanger............................................................ 30 Micron Bag Hanger ............1
................ AB430039 .............. Hanger (optional) ............................................. 5 Micron Bag Hanger ..............1
5.............. 523011W................ Hanger Bracket................................................ ..............................................1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram For 3 Phase 230V/460V Dust Collector (DC-1200M-3)
Wiring Diagram For Single Phase 230V Only Dust Collector (DC-1200M)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|