MICRO COMPONENT SYSTEM
UX-L5V
—Consists of CA-UXL5V and SP-UXL5V
SUPER VIDEO
For turning off the demonstration display, see
“How to cancel the demonstration” on page 1.
INSTRUCTIONS
LVT1987-006B
[US/UX/A/UA/UB/UW]
Download from Www.Somanuals.com. All Manuals Search And Download.
[European Union only]
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or
more.
Front view
Side view
SP-UXL5V CA-UXL5V SP-UXL5V
CA-UXL5V
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete
understanding and to obtain the best possible performance from the System.
Precautions
Installation
• Install the System in a location with adequate ventilation
to prevent internal heat build-up in the System.
How to Read This Manual
• Button and control operations are explained in the table
below.
• Some related tips and notes are explained later in
the sections “Learning More about This System”
and “Troubleshooting,” but not in the same section
DO NOT install the System in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or vibration.
explaining the operations (
indicates that the
INFO
content has some information).
Indicates that you press the button briefly.
• Install in a place which is level, dry and neither too hot
nor too cold—between 5°C and 35°C.
• Leave sufficient distance between the System and the TV.
• Keep the speakers away from the TV to avoid
interference with the TV.
Indicates that you press the button briefly
and repeatedly until the option you want
is selected.
Power sources
Indicates that you press one of the buttons.
• When unplugging the System from the wall outlet, always
pull on the plug, not the power cord.
2sec.
Indicates that you press and hold the
button for a specified period.
DO NOT handle the power cord with wet
hands.
Indicates that you turn the control in the
specified direction(s).
Moisture condensation
Moisture may condense on the lens inside the System in the
following cases:
• After starting to heat the room
• In a damp room
• If the System is brought directly from a cold to a warm
place.
Should this occur, the System may malfunction. In this
case, leave the System turned on for a few hours until the
moisture evaporates, unplug the power cord, then plug it
in again.
Remote
Indicates that this operation is only
possible using the remote control.
ONLY
Indicates that this operation is only
possible using the main unit.
Main Unit
ONLY
How to cancel the demonstration
Press and hold DEMO button on the main unit until
“DEMO CLR” appears while the System is on standby.
Internal heat
• Make sure there is good ventilation around the System.
Poor ventilation could overheat and damage the System.
DO NOT block the ventilation openings or
holes. If they are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.
Others
Should any metallic object or liquid fall into the System,
unplug the power cord and consult your dealer before
operating any further.
DO NOT disassemble the System since there
are no user serviceable parts inside.
• If you are not going to operate the System for an
extended period of time, unplug the power cord from the
wall outlet.
If anything goes wrong, unplug the power cord and consult
your dealer.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Connections ............................................................
4
Advanced Playback Operations ................................. 21
Programming the Playing Order—Program Play........... 21
Playing at Random—Random Play .................................. 22
Playing Repeatedly .............................................................. 22
Prohibiting Disc Ejection—Child Lock............................ 23
Preparing the Remote Control ..........................................
7
Display Indicators ....................................................
Daily Operations—Playback ....................................
8
9
Recording Operations .............................................. 24
Listening to the Radio......................................................... 10
Playing Back a Disc/USB Mass Storage Class Device..... 11
Playing Back Other Equipment......................................... 13
Recording from a Disc........................................................ 25
On-Screen Operations .............................................. 26
On-screen Bar Operations ................................................. 26
Control Screen Operations ................................................ 27
Daily Operations—Sound & Other Adjustments......... 14
Adjusting the Volume......................................................... 14
Adjusting the Sound............................................................ 14
Making Dialogues Clear—Clear Voice ............................ 15 Daily Timer Operations............................................. 29
Presetting Automatic DVD Sound Increase Level ......... 15
Changing the Display Brightness...................................... 15
Setting the ECO (ecology) Mode....................................... 15
Changing the Scanning Mode ........................................... 16
Setting the Clock.................................................................. 16
Turning Off the Power Automatically.............................. 17
Setting the Daily Timer....................................................... 29
Setup Menu Operations............................................ 31
Initial Settings ...................................................................... 31
Additional Information ............................................ 33
Learning More about This System.................................... 33
Maintenance......................................................................... 35
Troubleshooting .................................................................. 36
Display Messages for Recording Operations................... 37
Language Code List............................................................. 38
Specifications........................................................................ 39
Unique Video Disc/File Operations............................. 18
Selecting the Audio Track.................................................. 18
Selecting the Subtitle Language ......................................... 19
Selecting the View Angle.................................................... 19
Special Effect Playback........................................................ 20
Parts Index ............................................................. 40
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on Region Code
Playable Disc/File Types
DVD players and DVDs have their own Region Code
numbers. This System can play back only DVDs with an
appropriate Region Code number.
• For details, see page 39.
• “RG ERROR” appears if DVD with a wrong Region Code
is loaded.
Ex.:
COMPACT
SUPER VIDEO
DIGITAL VIDEO
DIGITAL AUDIO
• CD-R/-RW: Recorded in the Audio CD, Video CD,
and SVCD formats. MP3, WMA, JPEG, MPEG-1,
MPEG-2 and DivX files written in accordance with the
“ISO 9660” format can also be played.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard. Therefore,
the use of the Non-DVD side of a DualDisc in this product
may not be recommended.
• DVD-R/-RW, +R/+RW: Recorded in the DVD Video
format. MP3, WMA, JPEG, MPEG-1, MPEG-2 and
DivX files written in the UDF-Bridge format can also
be played.
• DVD-R/-RW: Recorded in the DVD Video Recording
(VR) format.
IMPORTANT: Before playing a disc/file, make sure of the
following...
• Turn on the TV and select an appropriate input mode
on the TV to view the pictures or on-screen displays.
• For disc/file playback, you can change the initial setting
to your preference. See “Setup Menu Operations” on
page 31.
If “INVALID KEY” appears on the TV screen when
you press a button, the disc/file cannot perform the
operation you have tried to do.
• USB mass storage class device: MP3, WMA, JPEG,
MPEG-1, MPEG-2 and DivX* files.
In addition to the above discs/files, this System can play
back audio data recorded on CD-Extra.
• The following discs cannot be played back:
DVD-RAM, CD-I (CD-I Ready), CD-ROM, and Photo
CD.
Playing back these discs will generate noise and damage
the speakers.
• When playing a multi-channel encoded software, the
System properly converts the multi-channel signals into
2 channels, and emits the downmixed sound from the
speakers. To enjoy the powerful sound of these multi-
channel encoded software, connect a proper decoder
or an amplifier with a proper built-in decoder to the
OPTICAL DIGITAL OUT terminal on the rear.
• CD Text and DVD Text can be played, but Text
information will not be shown on the display.
• In this manual, “file” and “track” are used
interchangeably.
• It is possible to play back finalized +R/+RW (DVD Video
format only) discs. DVD indicator lights on the front
display panel when a +R/+RW disc is loaded.
• “DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
• This System can play back EVERIO files (see page 34)
recorded on DVD, CD*, and USB mass storage class
device*.
* Only when the maximum bit rate is less than 2 Mbps.
About color system
This System accommodates both NTSC and PAL system
and can play back discs/files recorded in either system.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INFO
Connections
Do not connect the power cord until all other
connections have been made.
Supplied accessories
Check to be sure that you have all the following items.
• FM antenna (×1)
When connecting your TV:
• AM loop antenna (×1)
Connect your TV directly to the System. Connecting the
System to a TV via a VCR may interfere with your viewing
when playing back copy-protected discs/files. Connecting
an integrated TV/VCR system to the System may also
interfere with your viewing.
• Composite video cord (×1)
• Remote control, RM-SUXL5VU (×1)
• Lithium coin battery CR2025 (×1: inserted in the
remote control)
• AC plug adapter (×1)
(Not supplied for Australia, Hong Kong, Thailand and
Saudi Arabia.)
If any items are missing, consult your dealer
immediately.
Rear panel
! From the digital input of digital audio component
See page 5.
~ From AM/FM antenna
See page 5.
@ From the input of TV/monitor
See page 6.
⁄ From the powered subwoofer
See page 6.
¤ Voltage selector
Before plugging in, confirm the position of the voltage
selector. See page 6.
Ÿ From the speakers
See page 5.
# To a wall outlet
Plug in the power cord only after all connections have
been completed.
Front panel
From the other equipment
See page 6.
From the USB mass storage class device
See page 6.
From the headphones
4
Download from Www.Somanuals.com. All Manuals Search And Download.
~AM/FM antenna
To assemble the AM loop antenna
ŸSpeakers
• When connecting the speaker cords, match the polarity
of the speaker terminals: red to (+) and black to (–).
Press and hold
To connect the AM/FM antenna
FM antenna (supplied)
Insert
Release
Red
Extend it so that you can obtain the best
reception.
R
L
From right
speaker
From left
speaker
Black
Black
CAUTION: SPEAKER
IMPEDANCE 6 16
White
• DO NOT connect more than one speaker to
each terminal.
• DO NOT push or pull the speakers as this
will damage the foot spacers at the bottom of
the speakers.
AM loop antenna (supplied)
Turn it until the best reception is obtained.
• Keep the AM loop antenna cable wrapped around the
AM loop antenna frame, otherwise the effectiveness and
sensitivity of the AM loop antenna may be reduced.
!Digital audio component
For better FM reception
OPTICAL
OPTICAL
Optical digital
cord (not
supplied)
DIGITAL
DIGITAL
OUT
OUT
Protective cap
FM outdoor antenna
(not supplied)
• Set “AUDIO OUT” in the “ ” menu correctly according
to the connected digital audio equipment (see page 32).
• The digital signal through the OPTICAL DIGITAL OUT
terminal is transmitted only when “DVD/CD” is selected
as the source.
Disconnect the supplied FM antenna, and connect to an
outdoor FM antenna using a 75 Ω wire with coaxial type
connector.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
When connecting a USB mass storage class device
On the front
panel
⁄To connect the powered subwoofer
SUBWOOFER OUT
USB cable
(not supplied)
From the powered subwoofer
(not supplied)
The connected subwoofer can reproduce the bass sounds
recorded in front left and right channels, but cannot
reproduce the LFE signals encoded in multi-channel
software.
• When connecting with a USB cable, use the USB 2.0 cable
whose length is less than 1 m.
• You can connect a USB mass storage class device such as
a USB flash memory device, hard disk drive, multimedia
card reader, etc. to this System.
• Before plugging the System to the power supply, make
sure that the powered subwoofer is turned off.
• You cannot connect a computer to the USB MEMORY
REC/PLAY terminal (
) of the System.
@TV/monitor
Connect your TV using either the component video cord
or composite video cord.
• You cannot connect JVC Everio camcorder to the USB
MEMORY REC/PLAY terminal ( ) of the System.
• Noise and static electricity may stop the USB mass
storage class device sound. In this case, disconnect and
connect the USB mass storage class device again after
turning off the System.
Y
Green
B
P
R
P
• Depending on the shape of a USB mass storage class
device connected, you cannot open or close the disc tray
properly. In such a case, use a USB extension cable (not
supplied) to connect.
Yellow
Component video cord
(not supplied)
Red
Blue
When connecting other equipment
On the front
Composite video cord (supplied)
panel
Stereo mini plug
(not supplied)
• When you connect a TV using a component video cord,
you can enjoy a high quality picture by selecting the
progressive scanning mode. To select the scanning mode,
see page 16.
• After connecting a TV, select an appropriate color system
for your TV. To select the color system, see page 31.
From audio output (or headphone out, etc.)
¤Voltage selector
This operation is not required for Hong Kong and
Australian models.
Use a screwdriver to slide the voltage selector so that it is
pointing to the correct voltage in the area you are plugging
in the unit. (See also the back cover page.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Remote Control
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
When you use the remote control for the first time, pull out
the insulation sheet.
When using the remote control
Point the top of the remote control towards the remote
sensor as directly as possible. If you operate it from a
diagonal position, the operating range (approx. 5 m) may
be shorter.
Insulation sheet
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
• Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a
doctor immediately.
• To prevent the battery from overheating, cracking, or
starting a fire:
– Do not recharge, short, disassemble or heat the battery
or dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to
federal, state, and local regulations.
• The batteries (battery pack or batteries installed) shall not
be exposed to excessive heat source such as sunshine, fire
or the like.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Indicators
The indications on the display tell you a lot of things while you are operating the System.
Before operating the System, be familiar with when and how the indicators illuminate on the display.
1 SURROUND indicator
• Lights when surround sound is activated.
2 HP indicator
• Lights when headphones are connected to the System.
3 USB indicator
• Lights when “USB” is selected as the source.
4 Disc format indicators
• SVCD: lights when playing back an SVCD.
• VCD: lights when playing back a VCD.
• CD: lights when playing back a CD.
• DVD: lights when playing back a DVD.
5 REC (recording) indicator
q BASS indicator
• Lights when BASS (Hyper Bass Sound) is activated.
w Radio band indicators
• AM: lights when tuning in to an AM station.
• FM: lights when tuning in to an FM station.
e FM reception indicators
• ß (stereo): lights while an FM stereo station with
sufficient signal strength is tuned in.
• ˜ (monaural): lights while receiving an FM stereo
station in monaural.
r Daily Timer indicators
•
: lights when Daily Timer is on standby or is being
set; flashes while it is working.
• Lights when recording started.
6 Playback mode indicators
• 1/2/3: lights when a Daily Timer (1, 2, or 3) is on
standby; flashes while it is working or being set.
(Clear Voice) indicator
• Repeat Mode indicators:
–
–
–
: lights when One Track/File/Chapter Repeat is
t
1
activated.
: lights when One Group/Title/Original Program/
Play List Repeat is activated.
: lights when All Track/File/Title/Original
Program Repeat is activated.
• Lights when Clear Voice is activated.
y Main display
• While listening to the radio: band (or preset number)
and station frequency appear.
• While “AUDIO IN” is selected as the source: “AUDIO
IN” appears.
• RND: lights when Random Play is activated.
• PRGM: lights when Program Play is activated.
7 Audio format indicators
• MP3: lights when an MP3 file is detected.
• WMA: lights when a WMA file is detected.
8 PRGR. (progressive) indicator
• While playing a disc or file: current status appears.
u A.STBY (Auto Standby) indicator
• Lights when Auto Standby is activated.
• Flashes when playback stops with Auto Standby
activated.
• Lights when the progressive scanning mode is
selected.
i SLEEP indicator
• Lights when the Sleep Timer is activated.
9 S.TURBO (Sound Turbo) indicator
• Lights when Sound Turbo II is activated.
p RESUME indicator
• Lights when RESUME play is activated.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily Operations—Playback
In this manual, operations using the remote control
1 Turn on the power.
are mainly explained; however, you can use the buttons
and controls on the main unit if they have the same (or
similar) name and marks.
The STANDBY lamp on the main unit turns off.
• Instead of pressing
, the System is turned on by
pressing one of the source buttons.
2 Select the source.
Remote control
• Playback automatically starts if the selected source
is ready.
• For disc/USB: see page 11.
• For FM/AM: see page 10.
• For TV: see page 12.
• For AUDIO IN: see page 13.
• You can change the display information by pressing
DISPLAY. For details, see page 17.
3 Adjust the volume.
To turn off (standby) the System
The STANDBY lamp on the main unit
lights in red.
• A small amount of power is always
consumed even while on standby.
Number
buttons
For private listening
Connect a pair of headphones to the PHONES jack on
the main unit. The sound will no longer come out of the
speakers. The HP indicator lights up on the display. Be
sure to turn down the volume before connecting or
putting on the headphones.
• Disconnecting the headphones will activate the
speakers again.
DO NOT turn off (standby) the System
with the volume set at an extremely high
level; otherwise, the sudden blast of sound
may damage your hearing, speakers and/or
headphones when you turn on the System or
start playback.
How to select a number
Examples:
To select number 5, press 5.
To select number 10, press 10.
To select number 15, press 10,
1, then 5.
To select number 30, press 10
3, then 0.
To select number 125, press
10 twice (the underbar of the
hundred digit on the display
flashes), 1, 2, then 5.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INFO
Listening to the Radio
To select the band (FM or AM)
To select the AM tuner interval spacing
Some countries or regions space AM stations 9 kHz apart,
and others use 10 kHz spacing.
Before operating the tuner, select the appropriate AM tuner
interval spacing used in your residential area.
To tune in to a station
While FM or AM is selected...
1 Select “TUNER AM.”
2 Select the AM tuner interval spacing.
To select 9 kHz:
Frequency starts changing on the display.
When a station (frequency) with sufficient signal strength
is tuned in, the frequency stops changing.
• When you repeatedly press the button, the frequency
changes step by step.
To manually stop the search, press either button.
To select 10 kHz:
Remote
ONLY
If the FM reception is poor
The ˜ (monaural) indicator lights on the display.
Reception will improve though stereo effect is lost—
Monaural reception.
To restore the stereo effect, press the button again. The
˜ (monaural) indicator disappears.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
To preset the stations
Playing Back a Disc/USB Mass Storage Class
You can preset 30 FM and 15 AM stations.
1 Tune in to a station you want to preset.
2 Activate the preset number entry mode.
INFO
Device
Main Unit
To insert a disc
ONLY
• Finish the following process while the preset number
is flashing.
• When using an 8 cm disc, place it on the inner circle of
the disc tray.
3 Select a preset number for the station you store.
• To select a number, see
“How to select a number”
on page 9.
To close the disc tray, press 0 again.
• If you press DVD/CD 6, disc tray closes automatically
and playback starts (depending on how the disc is
programmed internally).
• You can also use the 3 or
2 button.
To connect a USB mass storage class device
• For connecting a USB mass storage class device, see page
6.
• Always set volume level to the minimum level when
connecting or disconnecting a USB mass storage class
device.
• To disconnect a USB mass storage class device safely,
turn off the System before disconnecting it.
4 Store the station.
Remote
ONLY
To play back a disc/USB mass storage class device
To tune in to a preset station
To start:
Disc USB mass storage class device
1 Select the band (FM or AM).
2 Select the preset number for the station you stored.
To pause:
To stop:
• To select a number, see
“How to select a number”
on page 9.
• You can also use the 3 or
2 button.
To release, press the same button
again.
• If different types of playable files (audio/still picture/
moving picture) are recorded, select a file type to play
(see the following).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
To store the stop point (Resume Play)
To select a chapter/track/file
You can store the stop point, and when you start playback
again by pressing DVD/CD 6 or USB 6 (even while
on standby), it starts from the position where you have
stopped.
• For VCD/SVCD, cancel PBC (see page 13).
While playing...
• When you press 4 for the
first time, you will go back to the
beginning of the current chapter/
track/file.
• The RESUME
indicator lights
on the display.
Remote
ONLY
(while holding...)
To locate a particular portion
To stop completely while Resume is activated, press 7
• This does not function for JPEG files.
twice. (To deactivate Resume, press RESUME again.)
While playing...
Remote
ONLY
To select the file type
Select a file type if different type of playable files (audio/still
picture/moving picture) are recorded.
• You can use the control screen on the TV. (For still/
moving picture files, it appears while playback is
stopped.) For details, see page 28.
1
• For MP3/WMA/MPEG-1/MPEG-2/DivX files, the search
speed and indications on the TV are different from those
above.
• No sound comes out if searching is carried out while
showing the moving picture.
(while holding...)
1
2
3
To return to normal playback, press DVD/CD 6 or
USB 6 (depending on the current source).
On the TV
1 Audio file
2 Still picture
Remote
ONLY
3 Moving picture
To locate an item directly
You can select a title/chapter/track/file directly and start
playback.
• For DVD Video, you can select a title before starting
playback, while you can select a chapter after starting
playback.
2 Select a file type.
• To select a number, see
“How to select a number” on
page 9.
Remote
ONLY
To select a title/group
• Not applicable for DVD-VR.
While playing...
(while holding...)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
To play back using the disc menu
For DVD Video:
To move to the next or previous page of the current
menu:
1 Show the disc menu.
Moves to the next page.
Moves to the previous page.
To return to the previous menu:
2 Select an item on the disc menu.
(while holding...)
To cancel PBC, press 7, then select a track by using the
number buttons (see page 9). Playback starts with the
selected track.
To reactivate PBC, press 7 (twice if RESUME is turned
on), then press DVD/CD 6.
• For some discs, you can also select items by entering
the number using the number buttons.
For SVCD/VCD with PBC:
Playing Back Other Equipment
While playing a disc with PBC, “PBC” appears on the
display.
• For connecting other equipment, see page 6.
When disc menu appears on the TV, select an item on the
menu. Playback of the selected item starts.
You can listen to the other equipment (digital audio player,
etc.) connected to the AUDIO IN jack.
• Make sure to turn down the volume on the System to
minimum level before starting playback.
• To select a number, see “How
to select a number” on page 9.
Remote
ONLY
To adjust the audio input level
If the sound from the device connected to the AUDIO IN
jack is too loud or too quiet, you can preset the audio input
level through the AUDIO IN jack (without changing the
volume level).
While “AUDIO IN” is selected as the source...
(while holding...)
• As the number of the level increases, the preset input
level is increased.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily Operations—Sound & Other Adjustments
Remote
ONLY
To drop the volume in a moment
Remote control
To restore the volume, press again, or
adjust the volume level.
Remote
ONLY
INFO
Adjusting the Sound
To activate surround mode
This is available only when disc or USB is selected for the
source.
(Canceled)
To reinforce the heavy sound
This boosts the low and high frequency sound—Sound
Turbo II.
TURBOOFF
(Canceled)
To reinforce the bass sound
The richness and fullness of the bass sound is clearly
maintained regardless of how you set the volume—HBS
(Hyper Bass Sound).
• When Sound Turbo II function is activated (see above),
the BASS indicator goes off and HBS button dose not
work.
Main unit
(Canceled)
To adjust the tone
You can adjust the bass and treble level from –3 to +3.
To adjust the bass
Adjusting the Volume
(Canceled)
You can adjust the volume level from “VOL MIN” (level 0)
to “VOL MAX” (level 40).
To adjust the treble
Remote control:
Main unit:
(Canceled)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Dialogues Clear
—Clear Voice
Changing the Display Brightness
You can dim the display.
Remote
ONLY
Clear Voice works for multi-channel software which
contains a center channel signal and for 2-channel
software.
• This only functions while listening to disc/USB mass
storage class device.
While the System is turned on...
(Canceled)
CLR ON
The display and the illumination dim.
The illumination is turned off.
The display dims automatically.
Cancels the dimmer function.
DIM 1
CLR OFF
(Canceled)
DIM 2
AUTO
Presetting Automatic DVD Sound
DIM OFF
Remote
ONLY
Increase Level
DVD sound is sometimes recorded at a lower level than
other discs and sources. You can set the increase level for
the currently loaded DVD, so you do not have to adjust the
volume when you change the source.
Setting the ECO (ecology) Mode
Setting the ECO mode allows you to reduce power
consumption by turning the display off while on standby.
• This only functions for DVD Video and DVD-VR.
While the System is on standby...
While “DVD/CD” is selected as the source...
(Canceled)
(while holding...)
Original recording level.
NORMAL
MEDIUM
Output level is increased (less than
“HIGH”).
Output level is increased (more than
“MEDIUM”). [Initial setting]
HIGH
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
INFO
INFO
Setting the Clock
Changing the Scanning Mode
Remote
ONLY
Without setting the built-in clock, you cannot use Daily
This System supports progressive scanning.
Timers (see page 29).
• To exit the clock settings, press CLOCK/TIMER as
required.
• To correct a mis-entry during the process, press
CANCEL (while holding SHIFT). You can return to the
previous step.
Select the video signal output according to the type of
your TV. If you connect a progressive TV through the
COMPONENT VIDEO OUT jacks, you can enjoy a high
quality picture playback by selecting “P-SCAN YPBPR.”
Before playback...
1 Activate the clock setting mode.
• If you have already adjusted the clock before, press
the button repeatedly until the clock setting mode is
selected.
(while holding...)
For a conventional TV.
Select when connecting the TV through
the VIDEO OUT jack.
INTERLACE-
YUV
2 Adjust the hour, then the minute.
For a progressive TV.
P-SCAN
YPBPR
Select to enjoy a progressive scanned
picture through the COMPONENT
VIDEO OUT jacks.
• The PRGR. (Progressive) indicator lights
on the display.
Now the built-in clock starts working.
To check the current clock time during playback
Ex.: While playing a disc...
*
Only while playing back a disc or USB mass storage class
device.
** Only while playing back the following discs/files:
MP3/WMA/JPEG/MPEG-1/MPEG-2/DivX files:
Group and file number.
DVD Video/DVD-VR: Title and chapter number.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer
Turning Off the Power
Automatically
Remote
ONLY
You can set the shut-off time so that you can go to bed
without turning off the System yourself.
Auto Standby
1 Specify the time (in minutes).
• This only functions while playing a disc or USB mass
storage class device.
The A.STBY indicator lights on the
display.
Canceled
2 Wait until the set time disappears.
When the playback stops, the A.STBY indicator starts
flashing. If no operation is done for about 3 minutes while
the indicator is flashing, the System turns off (standby)
automatically.
• Changing the source to “TUNER FM,” “TUNER AM,” or
“AUDIO IN” temporarily deactivates Auto Standby.
To check the time remaining until the shut-off time,
press SLEEP/A.STBY once.
• If you press the button repeatedly, you can change the
shut-off time.
To cancel this function, press and hold SLEEP/A.STBY
again.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Unique Video Disc/File Operations
Remote
ONLY
INFO
Selecting the Audio Track
Remote control
For DVD Video: While playing back a chapter/file
containing several audio languages, you can select the
language to listen to.
For DVD-VR/SVCD/VCD: While playing back a track,
you can select the audio channel to listen to.
SLOW
,
While playing a DVD Video...
Ex.:
SUBTITLE
AUDIO/MPX
ZOOM
[
]
:
1 ENGLISH
5.1CH
ANGLE
1
2
3
1 Language
2 Audio format
3 Channel
[
[
[
3 JAPANESE
:
[
1
ENGLISH
5.1CH
]
:
[
2
FRENCH
5.1CH
]
:
[
3
JAPANESE
5.1CH
]
While playing a DVD-VR or SVCD/VCD...
:[ ]
1
:[ ]
2
:[ ]
3
[
]
: MONO L
CHANNEL
CHANNEL
CHANNEL
CHANNEL
[
]
: MONO R
[
]
: MIX MONO
[
]
: STEREO
To listen to normal stereo
(2-channel) playback.
STEREO
To listen to the left audio channel.
To listen to the right audio channel.
MONO L
MONO R
MIX MONO
To listen to monaural sound the left
and right sounds are mixed.
• SVCD can have 4 audio channels. SVCD usually uses
these 4 channels to record two 2-channel recordings
(STEREO).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
Remote
ONLY
Selecting the View Angle
For DVD Video only: While playing back a chapter
containing multi-view angles, you can view the same scene
from different angles.
Selecting the Subtitle Language
For DVD Video: While playing back a chapter/file
containing subtitles in different languages, you can select
the subtitle language to display on the TV.
For DVD-VR: While playing, you can turn the subtitles on
or off.
For SVCD: While playing, you can select the subtitles even
if no subtitles are recorded on the disc.
While playing a DVD-Video...
While playing a DVD Video...
[
]
[
]
[
]
1/3
2/3
3/3
:
[
1/3
]
:
[
2/3
]
:
[
3/3
]
Ex.:
[
]
[
]
[
]
3 JAPANESE
[
]
[
]
[
]
:
1
ENGLISH
:
2
FRENCH
:
3
JAPANESE
While playing a DVD-VR...
While playing an SVCD...
:
:
:
:
:
[
]
OFF
[
[
[
[
]
]
]
]
1
2
3
4
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
INFO
To replay the previous scenes
(One-Touch Replay)
Special Effect Playback
Still picture playback
To display the still picture:
While playing...
• This function is only used while playing DVD Video/
DVD-VR.
While playing....
Disc
USB mass storage class device
The playback position moves back about
10 seconds before the current position
(only within the same title for DVD
Video).
To resume normal playback, press the same button
again.
Remote
ONLY
Zoom
1 While playing...
Remote
ONLY
Slow-motion playback
ZOOM 2
ZOOM 3
ZOOM 4
ZOOM 1/2
• This function is used only while playing DVD Video/
DVD-VR/SVCD/VCD.
ZOOM : OFF
ZOOM 1/4
ZOOM 1/3
While pausing....
• For JPEG file: not available during slide show.
2 Move the zoomed-in position.
• You cannot move the zoomed-in position when
“ZOOM 1/2,” “ZOOM 1/3,” or “ZOOM 1/4” is
selected.
Reverse slow
motion*
starts.
Forward
slow motion
starts.
SB 1/2
SF 1/2
SB 1/3
SB 1/4
SB 1/5
SB 1/6
SB 1/7
SB 1/8
SF 1/3
SF 1/4
SF 1/5
SF 1/6
SF 1/7
To cancel Zoom, press ZOOM repeatedly until “ZOOM :
OFF” appears on the TV.
Returns to
normal playback
Returns to
normal playback
* Only available for DVD Video.
To resume normal playback, press DVD/CD 6.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Playback Operations
Programming the Playing Order
Remote
ONLY
Remote control
INFO
—Program Play
You can arrange the playing order of the chapters/tracks/
files (up to 32) before you start playback.
• Program play cannot be used for DVD-VR and JPEG/
MPEG-1/MPEG-2/DivX files.
1 Before starting playback, activate Program Play.
RANDOM:[ON]
REPEAT
RANDOM:[OFF]
(Canceled)
T
C
T
C
T
C
T
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Number
buttons
On the display
PROGRAM
PLAY
CLEAR
On the TV (Ex. DVD)
2 Select chapters/tracks/files you want for Program
Play.
1 For DVD Video and MP3/WMA files: Select a title or
group number.
2 Select a chapter or track/file number.
• To select a number, input a number directly.
• To erase the entire program, select “CLEAR” on the
program menu screen.
3 Repeat step 2 until you complete your program.
4 Start playback.
Main unit
Playback starts in the order you have
programmed.
• You can also start playback by
selecting “PLAY” on the program
menu screen and then pressing
ENTER/SET.
To skip:
To pause:
To stop:
To release, press
the same button
again.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ONLY
To exit Program Play
Before or after playback...
INFO
Playing Repeatedly
For DVD Video:
While playing...
(Twice)
(Canceled)
Playing at Random
Remote
ONLY
For CD/SVCD/VCD:
While playing (without PBC for SVCD/VCD) or before
playback...
—Random Play
You can play all chapters or tracks at random.
• Random Play cannot be used for DVD-VR and JPEG/
MPEG-1/MPEG-2/DivX files.
1 Before starting playback, activate Random Play.
(Canceled)
RANDOM:[ON]
For DVD-VR:
While playing an Original Program...
RANDOM:[OFF]
(Canceled)
CHAPTER
(Canceled)
2 Start playback.
While playing a Play List...
Playback starts in random order.
CHAPTER
(Canceled)
To skip a chapter/ To pause:
track:
To stop:
For MPEG-1/MPEG-2/DivX/MP3/WMA/JPEG files:
While playing or before playback...
REP GROUP
To release, press
the same button
again.
(Canceled)
Repeats the current chapter.
Repeats the current title.
CHAPTER
TITLE
To exit Random Play
Before or after playback...
Repeats the current track/file.
Repeats the current group.
REP 1
REP GROUP
REP PG
REP PL
RANDOM:[ON]
Repeats the current original program.
Repeats the current Play List.
RANDOM:[OFF]
(Canceled)
Repeats all the contents or programmed
tracks/files.
REP ALL
22
Download from Www.Somanuals.com. All Manuals Search And Download.
A-B Repeat
Prohibiting Disc Ejection
—Child Lock
Main Unit
ONLY
You can repeat playback of a desired portion by specifying
the beginning (point A) and the ending (point B).
• A–B Repeat cannot be used for JPEG files and some
DVDs.
You can lock the disc tray so that no one can eject the
loaded disc.
• This function is available only while the System is on
standby.
1 While playing (without PBC for SVCD/VCD), select
the start point (A).
While the disc tray is closed...
(while holding...)
2 Select the end point (B).
Press the same button again.
• You can search for the end point using the ¡
button.
(while holding...)
To cancel the prohibition, repeat the same procedure.
“UNLOCK” appears on the display.
To cancel A-B Repeat, press REPEAT A-B (while holding
SHIFT) again.
• A-B Repeat will also be canceled when you stop play or
skip the chapter or track.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
INFO
Recording Operations
Before You Start Recording
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast or cable program and in any literary,
dramatic, musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Sound Turbo II, Hyper Bass Sound and tone adjustment
and surround mode effect (see pages 14 and 15) do not
affect recordings.
Remote control
• Random Play and Repeat Mode are canceled during
recording mode.
• You can record up to 99 tracks per group to the USB
device.
• This tracks which are recorded to the USB device will be
converted into MP3 format.
• You cannot start recording into a USB device while
“READING” is shown on the display.
• You cannot record tracks in the root group as much as
into other groups. This is not a malfunction. It depends
on the USB device used.
• Do not disconnect a USB device while playing/recording.
It may cause malfunction.
About SCMS (Serial Copy Management System)
The System uses the Serial Copy Management System
which allows only first-generation digital copies to be made
of premastered software such as regular CDs.
If you try to record from a duplicated CD-R or CD-RW
into the USB device, “SCMS VLT” appears on the display.
Main unit
1st generation
2nd generation
24
Download from Www.Somanuals.com. All Manuals Search And Download.
• The System will automatically create the new group
as “JVC_A01.” If “JVC_A01” already exists or the
number of tracks for one group is more than 99 tracks,
“JVC_A02,” “JVC_A03,” and so on will be created.
Both recording and playback start at the same time.
When playback ends, recording also stop.
Recording from a Disc
You can record tracks in digital recording from a CD onto
the USB device.
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
• You cannot change the source while recording.
• The tracks are recorded in the normal order even if
Program Play is activated.
Before recording....
Connect a recordable USB device to the USB MEMORY
REC/PLAY (
) terminal. (See also page 6.)
To stop recording
manually:
To record the playing
track (1 track):
1 Start and stop playback of the disc.
During play or pause...
(on the main unit)
2 Start recording.
(on the main unit)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Operations
The following information is displayed on the on-screen
bar. Items displayed depend on the types of disc or file.
Remote control
TT
CH
Title
Chapter
TRK
Track
Time indication
Audio language
Subtitle language
TOP MENU/
PG
MENU/PL
ENTER/SET
Angle
PCM
/
Audio format
Repeat mode
Playing back a disc with PBC
ON SCREEN
PBC
TIME SEARCH
Number
buttons
To remove the on-screen bar
SHIFT
Remote
ONLY
Time Search
On-screen Bar Operations
You can check the source information (disc/USB mass
storage class device) and playback status by using the on-
screen bar.
You can move to a particular point by specifying the
elapsed playing time from the beginning using the on-
screen bar.
• This function is not available during Program Play and
Random Play.
To display the on-screen bar
Ex: For DVD Video
1 While playing (without PBC for SVCD/VCD), display
elapsed playing time on the on-screen bar.
• Time Search can also be used before starting playback
(not applicable for DVD Video/DVD-VR).
DVD
TT 1/ 7
CH 1 /6
0 0: 0 0 : 00
1
2
3
4
1 Disc/source
2 Current title number/Total title number
2
3 Current chapter number/Total chapter number
4 Time indication
(while holding...)
Ex.: For DVD Video
DVD
T T 0 1 / 0 7 CH 0 0 1 / 0 0 6
0 0 :0 0 :4 1
Highlighted
Continued on the next page
26
Download from Www.Somanuals.com. All Manuals Search And Download.
To select playback type
3 Move the highlight to the time indication.
To display the Original
Programs:
To display the Play Lists:
DVD
TT 01/07 CH 001/006
0 0 : 00 : 4 1
4 Enter the time.
To remove the list, press the same button again.
You can specify the time in hours/minutes/seconds.
Ex.: When Original Program is selected.
0 0:0 0:0 0
ORIGINAL PROGRAM
NO DATE
CH
L
TIME
TITLE
The l
1
2
3
4
5
03/12/08
12:15:00
23:05:00
08:17:00
07:47:00
19:38:00
09/12/08
18/12/08
20/12/08
25/12/08
L
Seconds
Minutes
Hours
L
L
L
BOOM!
Mr. La
1
2
3
4
5 6
5 Confirm your entry.
The System starts playing the disc
from the selected playing time.
Ex.: When Play List is selected.
PLAY LIST
NO DATE
Chap Length
002 0:23:24
004 1:04:39
013 0:41:26
017 0:09:08
TITLE
Nebul
CDJ
Secret
S.Wal
1
2
3
4
03/12/08
15/12/08
24/12/08
27/12/08
Remote
ONLY
Control Screen Operations
You can search for and play the desired items through the
control screen for DVD-VR and MP3/WMA/JPEG/MPEG-
1/MPEG-2/DivX files.
1
2
7
8
5 6
1 Listed number
2 Recording/creating date
3 Recording channels
4 Recording time
5 Title
Control screen for DVD-VR
The control screen is superimposed onto the TV screen
when you call up Original Program (PG) or Play List (PL).
6 Highlight bar (current selection)
7 Chapters included
8 Playback time
To select an item in the list and start playback
• If you move the highlight bar, the selected item starts
playback automatically.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To move the highlight bar between group list and file list
Control screen for MP3/WMA/JPEG/MPEG-1/
MPEG-2/DivX files
Moves the bar to the file list.
The control screen appears on the TV when the System
detects MP3/WMA/JPEG/MPEG-1/MPEG-2/DivX files on
the loaded disc or connected USB mass storage class device.
• For JPEG/MPEG-1/MPEG-2/DivX, it appears when
playback is stopped.
Moves the bar to the group list.
• Items displayed on the screen depend on the type of the
file.
To select an item in the list
Move the highlight bar to the desired
item.
1
2 2
3
3
[
]
Rain. mp3
Summer
01. Summer
02. Spring
03. Fall
01. Cloudy
02. Rain
03.Fair
04. Fog
05. Hail
04. Winter
__________
__________
05.
06.
To start playback
06.indian summer
ALBUM
SONG
ARTIST
:
Summer
Rain
------
For JPEG:
:
:
The selected file (still picture) is
displayed until you change it.
4
5
Disc
Press one of the buttons
depending on the current source.
1 Folder/Group list
2 Current folder/Group
3 Current file/track
4 File/track information
5 File type
Slide-show playback starts. Each
file (still picture) is shown on the
USB mass storage class
device
screen for about 3 seconds, then
changes one after another.
6 File/track list
• To cancel slide-show and
display the current still picture,
press the same button again.
•
If different types of playable files (audio/still picture/
moving picture) are recorded on a disc or USB mass
storage class device, select a file type to play (see page
12).
For the other files:
Playback starts with the selected
track.
• Pressing DVD/CD 6 or
USB 6 also starts playback.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily Timer Operations
Remote
ONLY
INFO
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite
music.
Remote control
You can store three Daily Timer settings.
• To exit the timer settings, press CLOCK/TIMER as
required.
CLOCK/TIMER
• To correct a mis-entry during process, press CANCEL
(while holding SHIFT). You can go back to the previous
step.
1 Select one of the timer setting modes you want to
set—DAILY 1 ON time, DAILY 2 ON time, or DAILY
3 ON time.
Daily Timer 1
Daily Timer 2
Daily Timer 3
ON (Time)
ON (Time)
ON (Time)
Canceled
Clock setting
(See page 16.)
Ex.: When Daily Timer 1 setting mode is selected
• When the clock has not been set, pressing
CLOCK/TIMER makes the System enter the clock
setting mode (see page 16).
2 Set the timer as you like.
Repeat the procedure for the following settings until
finished.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Set the hour then the minute for on-time.
2 Set the hour then the minute for off-time.
3 Select the playback source—“DISC,” “USB,”
“TUNER FM,” “TUNER AM,” or “AUDIO IN.”
To turn on or off the Daily Timer
Since Daily Timer is activated at the same time everyday,
you may need to cancel it on some particular days.
To cancel the Daily Timer
1 Select the Timer (DAILY 1, DAILY 2, or DAILY 3)
you want to cancel.
• For “TUNER FM” or “TUNER AM”: Preset
channels can not be selected.
• For “DISC” or “USB”: File numbers cannot be
selected.
Daily Timer 1
Daily Timer 2
Daily Timer 3
4 Select the volume level.
ON (Time)
ON (Time)
ON (Time)
• You can adjust the volume level (“00” to “MAX
(39)” and “VOL – –”). If you select “VOL – –,” the
volume is set to the same level as when the System
was last turned off.
Canceled
Clock setting
(See page 16.)
Once settings are completed, the timer setting
information appears in sequence.
3 Turn off the System (on standby), if you have set the
Ex.: To cancel Daily Timer 1
timer with the System turned on.
2 Turn off the selected Timer.
How Daily Timer works
(while holding...)
Once the Daily Timer has been set, the timer indicator
(
) and timer number indicator (1/2/3) are lit on
To turn on the Daily Timer
the display. Daily Timer is activated at the same time
everyday until the timer is turned off manually (see the
next column) or another timer is activated.
1 Select the Timer (DAILY 1, DAILY 2, or DAILY 3)
you want to activate.
When the on-time comes
The System turns on, tunes in to the specified station or
starts playing from the specified source, and gradually
increases the volume level to the preset level after for 30
seconds.
Daily Timer 1
Daily Timer 2
Daily Timer 3
• While Daily Timer is working, the timer indicator (
flashes on the display.
)
ON (Time)
ON (Time)
ON (Time)
When the off-time comes
Canceled
Clock setting
(See page 16.)
The System stops playback, and turns off (on standby)
2 Activate the selected Timer.
automatically.
• The timer setting remains in memory until you change
it.
Ex.: When Daily Timer 1 (DAILY 1) is
activated
3 Wait until the indication disappears.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INFO
Setup Menu Operations
Remote
ONLY
Initial Settings
Remote control
You can change the settings of the System.
• The Setup Menu can be used only when “DVD/CD” or
“USB” is selected as the source.
PICTURE
ADJUST
1 Press SET UP while playback is stopped.
TV SYSTEM
SCREEN SAVER
VIDEO
TV TYPE
PASSWORD
RATI NG
DEFAULT
SET UP
2 Press 3 (or 2) to select the menu.
3 Press ∞ (or 5) to move to select the item.
4 Press ENTER/SET.
5 Press ∞ (or 5) to select the options, then press
ENTER/SET.
To remove a preference display
Press SET UP.
Menu
Item
Contents
TV SYSTEM
SCREEN SAVER
VIDEO
You can select the TV system between NTSC and PAL depending on the type of
the TV connected.
You can set the screen saver function (ON or OFF). If no operation is done for
about 5 minutes, the TV screen dims.
Select the video signal output according to the TV connected. (For details, see
“Changing the Scanning Mode” on page 16.)
You can select the monitor type to match your TV when you play back picture
recorded for wide-screen televisions.
TV TYPE
16:9
4:3 LB
4:3 PS / 4:3 MULTI PS (Pan Scan conversion): For a conventional (4:3) TV. The
picture is zoomed in to fill the screen vertically and the left and right sides of the
picture are cut off.
4:3 LB / 4:3 MULTI LB (Letter Box conversion): For a conventional (4:3) TV.
Displays a wide-screen picture to fit the width of the TV screen keeping the aspect
ratio.
16:9 / 16:9 MULTI (Wide-screen television): Select this when the aspect ratio of
your wide-screen TV is fixed to 16:9.
• For multi-color system TVs, select the “MULTI” type.
4:3 PS
PASSWORD
You can prohibit operations used for changing the RATING setup. Enter a four-
digit password. We recommend that you write your password here for your
reminder.
Password:
&&&&
If you forget your password, you can release it by entering 0000.
You can set playable rating level with the System.
RATING
You can set all the items on the Setup menu to the default settings except for the
PASSWORD setting.
DEFAULT
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Item
Contents
OSD LANGUAGE
You can select the language displayed on the screen—“ENGLISH,” “CHINESE” or
“SPANISH.”
You can select the initial audio language for DVD Video. (See also page 38.)
You can select the initial subtitle language for DVD Video. (See also page 38.)
You can select the initial menu language for DVD Video. (See also page 38.)
AUDIO LANG
SUBTITLE LANG
MENU LANG
DIVX [R] VOD
The System has its own Registration Code.
If necessary, you can confirm it.
Once you have played back a DivX file in which the Registration Code is recorded,
the System’s Registration Code is overwritten for copyright protection.
Set this item correctly when using the OPTICAL DIGITAL OUT terminal on the
rear.
AUDIO OUT
SPDIF/OFF: Digital output is disabled.
SPDIF/RAW: Select this when connecting an amplifier or a decoder compatible
with Dolby Digital.
SPDIF/PCM: Select this when connecting an amplifier or a decoder incompatible
with Dolby Digital or MPEG Audio, or when connecting to a recording device.
You can set the surround mode. (For details, see “To activate surround mode” on
page 14.)
3D PROCESSING
You can adjust the brightness. (0 to 12)
You can adjust the contrast. (0 to 12)
You can adjust the hue. (–6 to +6)
BRIGHTNESS
CONTRAST
HUE
*
You can adjust the color depth. (0 to 12)
You can adjust the sharpness. (0 to 8)
SATURATION
SHARPNESS
DYNAMIC RANGE
You can select the Dynamic Range Compression (DRC) for night-time listening.
DRC reduces the difference between normal voices and the sound (such as the
sound of explosion).
The effect of DRC is as follows.
FULL
6/8
4/8
2/8
Low)
(High
When “OFF” is selected, the effect is not available.
You can select the playback sound (channel) you want to while playing digital
software recorded (or broadcasted) in Dual Mono mode, which includes two
monaural channels separately.
DUAL MONO
*
You can enter the “ ” menu directly by pressing PICTURE ADJUST (while holding SHIFT).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
• For playback of files in the USB mass storage class
Learning More about This System
device...
– When connecting a USB mass storage class device, refer
also to its manual.
Connections (see pages 4 to 7)
• Make sure the antenna conductors do not touch any
other terminals, connecting cords or the power cord.
Also, keep the antennas away from metallic parts of the
System, connecting cords, and the power cord. These
could cause poor reception.
– Connect one USB mass storage class device to the
System at a time. Do not use a USB hub.
– You cannot charge any USB mass storage class device
through the USB MEMORY REC/PLAY (
terminal.
)
• Use only speakers with the same speaker impedance
as indicated by the speaker terminals on the rear of the
System.
• The speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly,
it may cause color distortions. So, pay attention to the
following when installing the speakers.
– When placing the speakers near a TV set, turn off the
TV’s main power switch or unplug it before installing
the speakers.
Then wait at least 30 minutes before turning on the
TV’s main power switch again.
– While playing back a file in a USB mass storage class
device, do not disconnect the device. It may cause
malfunction on both the System and the device.
– This System is compatible with USB 2.0 Full Speed.
– You cannot play back a file larger than 2 Gigabytes.
– When playing a file of a large transfer rate, frames or
sounds may be dropped during playback.
– This System cannot recognize a USB mass storage
class device whose rating is other than 5 V and exceeds
500 mA.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
– It will take some time to start up a digital audio player
whose contents are larger than 1 Gigabyte.
• For DVD-VR playback...
– This System can play only a disc of UDF-Bridge format.
– For details about DVD-VR format and Play List, refer
to the manual of the recording equipment.
• For MP3/WMA playback...
– MP3/WMA discs require a longer readout time than
regular CDs. (It depends on the complexity of the
group/file configuration.)
– Some MP3/WMA files cannot be played back and will
be skipped. This results from their recording processes
and conditions.
– This System can play only a disc of ISO 9660 Level 1 or
Level 2.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– Some TVs may still be affected even though you have
followed the above instructions. If this happens, move
the speakers away from the TV.
Daily Operations—Playback (see pages 9 to 13)
Listening to the Radio:
• If you store a new station into an occupied preset
number, the previously stored station in that number will
be erased.
• When you unplug the power cord or if a power failure
occurs, the preset stations will be erased in a few days. If
this happens, preset the stations again.
Playing Back a Disc/USB Mass Storage Class Device:
JVC bears no responsibility for any loss of data in the
USB mass storage class device while using this System.
• When you change the source to “DVD/CD” or “USB,” it
may take a while to activate the source.
• While the System is reading a disc, the source may not
change to “USB” properly. In this case, press 7, then
reselect “USB” as the source.
• On some discs, the actual operations may be different
from what is explained in this manual due to the
programming and disc structure; such differences are not
a malfunction of this System.
• The System recognizes up to 999 tracks (files) and 130
groups per disc/USB mass storage class device.
The total number of tracks (files) that the System can
detect is 4 000.
– If there are any unplayable files in a folder, those files
are also counted in the total file number.
– Playable files which do not belong to any groups are
handled as GROUP 1.
– It is recommended that you make each MP3/WMA
files as following conditions: At a sample rate of
44.1 kHz and at a data transfer rate of 128 kbps.
This System cannot play back files made at a bit rate of
less than 64 kbps.
• For JPEG files playback...
– It is recommended that you record a file at 640 x 480
resolution. (If a file has been recorded at a resolution
of more than 640 x 480, it will take a long time to be
shown.)
– This System can play back JPEG files with the extension
code <.jpg> or <.jpeg> (regardless of the letter case—
upper/lower).
– This System may not play back JPEG files properly if
they are recorded from a device other than a digital
camera.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
• For MPEG-1/MPEG-2 playback...
Daily Operations—Sound & Other Adjustments
(see pages 14 to 17)
– This System can play back MPEG-1/MPEG-2 files with
the extension code <.mpg>, <.mpeg>, or <.mod>*.
* <.mod> is an extension code used for the MPEG-2 files
recorded by JVC Everio camcorders. The MPEG-2 files
with the <.mod> extension code cannot be played back
if HD format is used or its maximum bit rate is more
than 2 Mbps.
Adjusting the Sound:
• This function also affects the sound through the
headphones.
Changing the Scanning Mode:
• Do not change the scanning mode to progressive in the
following cases:
– The stream format should conform to MPEG system/
program stream.
– 720 x 576 pixels (25 fps) / 720 x 480 pixels (30 fps) is
recommended for the highest resolution.
– This System also supports the resolutions of 352 x 576 /
480 x 576 / 352 x 288 pixels (25 fps) and 352 x 480 /
480 x 480 / 352 x 240 pixels (30 fps).
– When your TV does not support the progressive video
input.
– When you have not connected your TV to the system
using a component video cord.
• When you play back an NTSC disc/file in progressive
scanning mode, the System outputs the NTSC signal
regardless of the color system settings.
– The file format should be MP@ML (Main Profile at
Main Level)/SP@ML (Simple profile at Main Level)/
MP@LL (Main Profile at Low Level).
Setting the Clock:
– Audio streams should conform to MPEG1 Audio
Layer-2 or MPEG2 Audio Layer-2.
• “0:00” will flash on the display until you set the clock.
• The clock may gain or lose 1 to 2 minutes per month. If
this happens, reset the clock.
• For DivX playback...
– This System can play only a disc of UDF-Bridge format.
“Multi-border” is not supported.
– The System supports all versions of DivX video.
Unique Video Disc/File Operations (see pages 18
to 20)
®
– The System supports DivX files whose resolution is
720 x 480 pixels or less (30 fps), and 720 x 576 pixels or
less (25 fps).
Selecting the Audio Track:
• On some discs/files, you cannot change audio language
during playback.
– Audio stream should conform to Dolby Digital,
MPEG1 Audio Layer-2 or MPEG Audio Layer-3
(MP3).
– This System can play back DivX files with the extension
code <.divx> <.div> <.avi> (regardless of the letter
case—upper/lower).
– The System does not support GMC (Global Motion
Compression).
– The file encoded in the interlaced scanning mode may
not be played back correctly.
Special Effect Playback:
• During slow-motion playback, no sound will be emitted.
• While zoomed in, the picture may look coarse.
Advanced Playback Operations (see pages 21 to
23)
Programming the Playing Order—Program Play:
• While programming steps...
Your entry will be ignored if you have tried to program
an item number that does not exist (for example,
selecting track 14 on a disc that only has 12 tracks).
Playing Repeatedly:
• A-B Repeat is available only within the same title/original
program/track.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Operations (see pages 24 and 25)
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
Maintenance
To get the best performance of the System, keep your discs
and mechanism clean.
Daily Timer Operations (see pages 29 and 30)
Handling Discs
Setting the Daily Timer:
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• When you unplug the power cord or if a power failure
occurs, the timer will be canceled. You need to set the
clock first, then the timer again.
• If you set DVD Video as the source, Daily Timer will not
work correctly.
• If you set the Sleep Timer after Daily Timer starts playing
the selected source, Daily Timer is canceled.
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, extreme temperature,
and moisture.
To clean the disc:
Setup Menu Operations (see pages 31 and 32)
Wipe the disc with a soft cloth in a straight line from center
to edge.
General:
• If the upper and lower parts of the menu are cut off,
adjust the picture size control of the TV.
Cleaning the System
menu:
TV SYSTEM
• Stains should be wiped off with a soft cloth. If the System
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean
with a dry cloth.
• If you play back a PAL disc/file with the color system set
to “NTSC” you can watch the playback pictures, but the
following symptoms may occur:
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.
– The items on the menu will be blurred, and be shown
slightly shifted when highlighted.
– The aspect ratio of the picture may differ from the
original aspect ratio.
– The picture movement is not smooth.
TV TYPE
• Even if “4:3 PS / 4:3 MULTI PS” is selected, the screen
size may become 4:3 letter box while playing a disc/file.
This depends on how the discs are recorded.
• When you select “16:9 / 16:9 MULTI” for a picture whose
aspect ratio is 4:3, the picture changes slightly due to the
process of converting the picture width.
menu:
• When the language you have selected for “MENU
LANG,” “AUDIO LANG,” or “SUBTITLE LANG” is
not recorded, the original language is used as the initial
language.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc/USB mass storage class device Playback
Troubleshooting
Operations
General
The disc does not play.
Adjustments or settings are suddenly canceled before you
finish.
] You have inserted a disc whose Region Code is not
correct. (“RG ERROR” appears on the display.)
] The disc is placed upside down. Place the disc with the
label side facing up.
] There is a time limit. Repeat procedure again.
Operations are disabled.
] The built-in microprocessor may malfunction due to
external electrical interference. Unplug the power cord
and then plug it back in.
ID3 Tag on an MP3 file cannot be shown.
] There are two types of ID3 Tag—Version 1 and Version
2. This System can only show ID3 Tag Version 1.
Unable to operate the System from the remote control.
] The path between the remote control and the remote
sensor on the System is blocked.
Groups and tracks are not played back as you expect.
] The playing order is determined when the groups
and tracks were recorded. It depends on the writing
application.
] The batteries are exhausted.
No sound is heard.
MP3, WMA, JPEG, MPEG-1, MPEG-2 or DivX files are
not played back.
] The disc or the USB mass storage class device may
contain different types of files (ex. MP3/WMA/JPEG).
In this case, you can only play back the files selected by
pressing FILE TYPE (while holding SHIFT) (see page
12).
] You have changed the “FILE TYPE” setting after the
System read the disc or the USB mass storage class
device. In this case, reload the disc or disconnect the
USB mass storage class device and connect it again.
] Speaker connections are incorrect or loose.
] Headphones are connected.
No picture appears on the TV screen.
] The video cord connections are incorrect or loose.
No picture is displayed on the TV screen, the picture is
blurred, or the picture is divided into two parts.
] The System is connected to a TV which does not
support progressive video input.
] Incorrect scanning mode is selected (see page 16).
] When you unplug the power cord and plug it back
again, the scanning mode may change back to the initial
setting (“INTERLACE-YUV”) (see page 16).
The disc sound is discontinuous.
] The disc is scratched or dirty.
No subtitle appears on the display though you have
selected the initial subtitle language.
] Some DVDs are programmed not to display any subtitle
initially. If this happens, press SUBTITLE after starting
play back (see page 19).
The left and right edges of the picture are missing on the
screen.
] Select “4:3 LB / 4:3 MULTI LB” for “TV TYPE” (see
page 31).
Radio Operations
Audio language is different from the one you have
selected as the initial audio language.
] Some DVDs are programmed to always use the original
language initially. If this happens, press AUDIO/MPX
after starting playback (see page 18).
Hard to hear broadcasts because of noise.
] Antenna connections are incorrect or loose.
] The AM loop antenna is too close to the System.
] The FM antenna is not properly extended and
positioned.
The disc tray does not open or close.
] The power cord is not plugged in.
] Child Lock is in use. “TRAYLOCK” appears in the
display (see page 23).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Operations
Display Messages for Recording
Operations
Unable to record into the USB device.
] The capacity of the USB device is full.
] You have recorded 99 tracks or 100 groups on the USB
mass storage class device.
NO USB
• No USB device is connected or the connected USB device
is not compatible with this System.
] The USB device is write-protected.
] The USB device you connected is incompatible to this
System.
FILEFULL
• The USB memory has exceeded the maximum number of
files it can support.
Timer Operations
Daily Timer does not work.
] The System has been turned on when the on-time came.
Timer starts working only when the System is turned
off.
W. (write) PROT
• The USB device is write-protected.
SCMS VLT (violation)
• You have tried to copy from a duplicated disc to the USB
device.
Daily Timer does not start playback.
] The loaded disc is a DVD Video. Change the disc.
D. (device) FAIL
• The unit failed to read the USB device.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
Afar
Scots Gaelic
Galician
Maori
Shona
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
GD
GL
GN
GU
HA
HI
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
SN
SO
SQ
SR
SS
Abkhazian
Afrikaans
Ameharic
Arabic
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Guarani
Gujarati
Hausa
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Hindi
ST
Croatian
Armenian
Interlingua
Interlingue
Inupiak
Malay (MAY)
Maltese
HR
HY
IA
SU
SV
SW
TA
TE
Burmese
Nauru
IE
Nepali
Telugu
Tajik
IK
Indonesian
Icelandic
Hebrew
Dutch
IN
TG
TH
TI
Bislama
Bengali, Bangla
Tibetan
Breton
Norwegian
Occitan
Thai
IS
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
BN
BO
BR
CA
CO
CY
IW
JI
Yiddish
(Afan) Oromo
Oriya
OM
OR
PA
PS
TK
TL
Javanese
Georgian
Kazakh
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Catalan
Corsican
Welsh
Panjabi
TN
TO
TR
TS
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Turkish
Tsonga
Tatar
PT
Danish
DA
DZ
EL
QU
RM
RN
RO
RW
SA
Bhutani
Greek
TT
Twi
TW
UK
UR
UZ
VI
Esperanto
Estonian
Basque
Rumanian
Kinyarwanda
Sanskrit
Ukrainian
Urdu
EO
ET
Kirghiz
Uzbek
EU
FA
FI
Persian
Finnish
Fiji
Latin
Sindhi
Vietnamese
Volapuk
Wolof
SD
SG
Lingala
Sangho
VO
WO
XH
YO
ZU
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Serbo-Croatian
Singhalese
Slovenian
Samoan
FJ
SH
SI
Faroese
Frisian
Xhosa
FO
FY
Yoruba
Zulu
LV
MG
SL
Irish
GA
SM
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Power consumption:
30 W (at operation)
8 W (at standby)
Specifications
1 W or less (at ECO mode)
165 mm × 259 mm × 258 mm
(W/H/D)
Amplifier section—CA-UXL5V
Dimensions (approx.):
Mass (approx.):
Output Power: 60 W (30 W + 30 W) at 6 Ω (10% THD)
Audio Input:
AUDIO IN: Stereo mini (φ 3.5 mm)
500 mV/50 kΩ (at “LEVEL 1”)
250 mV/50 kΩ (at “LEVEL 2”)
125 mV/50 kΩ (at “LEVEL 3”)
1.9 kg
Speakers—SP-UXL5V (Magnetically-shielded Type)
Audio output: SUBWOOFER OUT: 500 mV/10 kΩ
Digital output: OPTICAL DIGITAL OUT:
–21 dBm to –15 dBm (660 nm 30 nm)
Speaker units: Tweeter:
Woofer:
Impedance:
1.5 cm x 1
10 cm cone x 1
6 Ω
Digital input:
USB MEMORY REC/PLAY
Dimensions (approx.):
140 mm × 250 mm × 188 mm
(W/H/D)
AV: Color system: PAL/NTSC (interlaced/progressive)
VIDEO OUT:
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
Mass (approx.):
1.5 kg each
COMPONENT VIDEO OUT: (Y)
(PB/PR) 0.7 V(p-p)/75 Ω
6 Ω – 16 Ω
Supplied Accessories
See page 4.
Speaker impedance:
Tuner section
Design and specifications are subject to change without
notice.
FM tuning range: 87.50 MHz – 108.00 MHz
AM tuning range: 531 kHz – 1 710 kHz (at 9 kHz intervals)
530 kHz – 1 710 kHz (at 10 kHz intervals)
• Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby Laboratories.
• DivX® is a registered trademark of DivX, Inc., and is used under
license.
• ABOUT DIVX VIDEO: DivX® is a digital video format created
by DivX, Inc. This is an official DivX Certified or DivX Ultra
Certified device that plays DivX video.
For Saudi Arabia: 531 kHz – 1 602 kHz (at 9 kHz intervals)
530 kHz – 1 600 kHz (at 10 kHz intervals)
Disc player section
Region codes: • Middle East: 2
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX® Certified
device must be registered in order to play DivX Video-on-
Demand (VOD) content. First generate the DivX VOD
registration code for your device and submit it during the
registration process. [Important: DivX VOD content is protected
by a DivX DRM (Digital Rights Management) system that
restricts playback to registered DivX Certified devices. If you
try to play DivX VOD content not authorized for your device,
the message “Authorization Error” will be displayed and your
• Plays DivX® video
• South East Asia, Hong Kong: 3
• Central and South America, Australia: 4
Playable disc:
• DVD Video/CD/VCD/SVCD
• CD-R/CD-RW (CD/SVCD/VCD/MP3/WMA/JPEG/
MPEG-1/MPEG-2/DivX format)
• DVD-R/-RW (DVD-VR/DVD Video/MP3/WMA/
JPEG/MPEG-1/MPEG-2/DivX format)
• +R/+RW (DVD Video/MP3/WMA/JPEG/MPEG-1/
MPEG-2/DivX format)
• Microsoft and Windows Media are either registered trademarks
or trademarks of Microsoft Corporation in the United States
and/or other countries.
Dynamic range:
Horizontal resolution:
Wow and flutter:
80 dB
500 lines
Immeasurable
• This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be
authorized by Macrovision, and is intended for home and
other limited viewing uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is prohibited.
• “CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT
IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR
TV SET COMPATIBILITY WITH THIS MODEL 525p AND
625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.”
USB section
Playable files:
MP3/WMA/JPEG/MPEG-1/MPEG-
2/DivX format
CD Recording format: MP3
USB specification: Compatible with USB 2.0 Full Speed
Compatible device: Mass storage class
Compatible system: FAT16, FAT32
Bus power supply: DC 5 V 500 mA
General
Power requirements:
AC 110 V– 127 V/AC 220 V– 240 V
with the voltage selector), 50 Hz/60 Hz
For Australia:
For Hong Kong:
(adjastable
AC 240 V , 50 Hz
AC 220 V , 50 Hz
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Index
Remote control
Name
Page
9, 30
Remote control
f
j
6
h
/
g
r
d
,
t
x
o
.
1
2
P
5
3
z
m
h
;
k
v
q
2
8
n
Q
g
1
p
i
s
6
;
e
u
b
7
a
9
4
l
y
7
10 – 13, 21, 22, 25, 33
12, 23
10, 12, 13, 21, 22
10 – 13, 16, 20, 21, 27 – 31
20
19
9, 13
13
18
15
15
16, 29, 30
16, 29, 30
9, 16
15
9, 11 – 13, 20 – 22, 25, 28
15
14
12
12
14
13, 27
9, 11 – 13, 27
26
32
22
23
12
13
1, ¡
4, ¢
5, ∞, 2, 3, ENTER/SET
(One Touch Replay)
ANGLE
AUDIO IN
AUDIO IN LEVEL
AUDIO/MPX
BASS/TRE
C.VOICE
CANCEL
CLOCK/TIMER
DISPLAY
DVD LEVEL
DVD/CD 6
ECO/DIMMER
FADE MUTING
FILE TYPE
GROUP/TITLE SKIP
HBS
MENU/PL
Number buttons
ON SCREEN
PICTURE ADJUST
REPEAT
REPEAT A-B
RESUME
RETURN
SCAN MODE
SET UP
16
31
SHIFT
12, 13, 15, 16, 23, 26, 29, 30, 32
17
20
14
19
14
26
13, 27
SLEEP/A.STBY
SLOW 9, (
S.TURBO II
SUBTITLE
SURROUND
TIME SEARCH
TOP MENU/PG
TUNER
TUNER/PLAY MODE
USB 6
VOLUME +, –
ZOOM
9, 10
10, 21, 22
9, 11, 12, 20 – 22, 28
9, 14, 15
20
Main unit
Name
Page
9
Main unit
2
7
10, 11, 13, 23, 25, 33
#
0
11, 23
$
¢, 4
10, 12, 13, 21, 22
4, 6, 13
25
11, 23
!, @
%
AUDIO IN jack
CD 3 USB REC
Disc tray
7
9
Display
DVD/CD #/8
8
-
9, 11, 20 – 22, 25, 28
4
ECO
15
1, 15
4, 9
7
8
DIMMER, DEMO
PHONES jack
Remote sensor
STANDBY lamp
TUNER/AUDIO IN/TV
USB MEMORY #/8
USB MEMORY REC/PLAY terminal
VOL +, VOL –
8
0
1
9
3
9 – 11, 13
9, 11, 20 – 22, 28
4, 6
6
5
^
9, 14
=, ~
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Mains (AC) Line Instruction
(Not applicable for Australia and Hong Kong)
CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage cor-
responds with the position of the voltage selector switch provided on the
outside of this equipment and, if different, reset the voltage selector switch,
to prevent from a damage or risk of fire/electric shock.
EN
© 2009 Victor Company of Japan, Limited
0309KMMMDWCDT
Download from Www.Somanuals.com. All Manuals Search And Download.
|