JVC Stereo Receiver rx 8010vbk User Manual

AUDIO/VIDEO CONTROL RECEIVER

RX-8010VBK

CATV/DBS VCR 1

POWER POWER

DVD DVD MUILTI

POWER

AUDIO

POWER

FM/AM

PHONO

USB

TV/DBS

VCR 1

VIDEO

CDR

VCR 2 TAPE/MD

SURROUND DSP ANALOG/DIGITAL SLEEP

ON/OFF

MODE

INPUT

RX-8010V AUDIO/VIDEO CONTROL RECEIVER

BASS

LINE DIF.ECT BOOST

ROOM

SIZE

EFFECT

MIDNIGHT

FM/AM TUNING

FM/AM PRESET

FM MODE

MEMORY

MODE

TEST

CTRTONE LIVENESS

STANDBY

POWER

ENTER

∗

MASTER VOLUME

SOUND

SUBWFR L/R BAL

CENTER

∗

7/P

MUTING DIGITALEQ REAR L

REAR R

∗

+10

100

RETURN FM MODE

SPEAKERS ON/OFF

CATV/DBS

CONTROL

TV/VIDEO

BAL L

∗

DVD MULTI

DVD

VCR

VIDEO

TV SOUND/DBS

SOUCE NAME

INPUT

DIGITAL LEVEL

EQ ADJUST

SURROUND ON/OFF

DSP MODE

ANALOG/DIGITAL MIDNIGHT MODE

LINE DIRECT

BASS BOOST

CH/ LEVEL TV VOL

VOLUME

∗

−

INPUT ATT

VIDEO

L—AUDIO—R

BAL R

∗

SUBWOOFER OUT ON/OFF

PLAY

EXIT

EFFECT SETTING

CONTROL

USB AUDIO

S-VIDEO

VIDEO

PHONO

CDR

TAPE

MD USB AUDIO

FM / AM

TEXT

/REW

FF/

PAUSE

SET

DISPLAY

DOWN

REC

PAUSE

DOWN

–

TUNING

–

SOUCE NAME

STOP CONTROL

PHONES

RM-SRX8010J

A/V CONTROL RECEIVER

D I G I T A L

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

LVT0618-001A

[J]

Download from Www.Somanuals.com. All Manuals Search And Download.

For Canada/pour Le Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS

B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL

APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING

EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”

ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE

BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS

NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME

SUR LE MATERIEL BROUILLEUR; “APPAREILS

NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES

COMMUNICATIONS.

For Canada/pour le Canada

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQUAU FOND

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the

manufacturer for compliance could void the user’s authority to

operate the equipment.

Caution: Proper Ventilation

Attention: Ventilation Correcte

To avoide risk of electric shock and fire and to protect from dam-

age.

Pour éviter les chocs électriques, l’incendie et tout autre dégât.

Disposer l’appareil en tenant compte des impératifs suivants

Locate the apparatus as follows:

Avant:

Rien ne doit gêner le dégagement

Laisser 10 cm de dégagement latéral

Laisser 10 cm de dégagement supérieur

Laisser 15 cm de dégagement arrière

Rien ne doit obstruer par dessous; poser l’appareil

sur une surface plate.

Front:

Sides:

Top:

No obstructions open spacing.

Flancs:

Dessus:

Arrière:

Dessous:

No obstructions in 10 cm from the sides.

No obstructions in 10 cm from the top.

No obstructions in 15 cm from the back

No obstructions, place on the level surface.

Back:

Bottom:

In addition, maintain the best possible air circulation as illustrated.

Veiller également à ce que l’air circule le mieux possible comme

illustré.

Spacing 15 cm or more

Dégagement de 15 cm

ou plus

RX-8010VBK

Wall or obstructions

Mur, ou obstruction

Front

Avant

Stand height 15 cm or more

Hauteur du socle: 15 cm ou plus

Floor

Plancher

G-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Ta ble of Cont ent s

P a r t s Ident ifica t ion ...................................... 2

Get t ing S t a r t ed ........................................... 3

Cr ea t ing a S ur r ound Field in Your Room ....... 2 4

7 Surround modes.................................................................... 24

7 DSP modes ........................................................................... 24

Reproducing the Sound Field .................................................... 25

Available DSP Modes According to the Speaker Arrangement .. 26

Adjusting the Surround Modes ................................................ 27

Adjusting the DAP Modes ....................................................... 28

Adjusting the Surround Modes with the DAP Modes.............. 30

Adjusting the 5 CH/4 CH Stereo Mode ................................... 32

Adjusting the 3D-PHONIC Modes .......................................... 33

Before Installation ...................................................................... 3

Checking the Supplied Accessories ........................................... 3

Connecting the FM and AM Antennas ....................................... 3

Connecting the Speakers ............................................................ 4

Connecting Audio/Video Components ....................................... 5

7 Analog Connections ............................................................... 5

7 Digital Connections ................................................................ 8

7 USB Connection ..................................................................... 9

Connecting the Power Cord ..................................................... 10

Putting Batteries in the Remote Control .................................. 10

Us ing t he DVD M ULTI P la yba ck M ode .......... 3 5

Activating the DVD MULTI Playback Mode .......................... 35

Ba s ic Oper a t ions ....................................... 1 1

Us ing t he On-S cr een M enus ........................ 3 6

Turning the Power On and Off (Standby) ................................ 11

Selecting the Source to Play ..................................................... 11

Adjusting the Volume ............................................................... 12

Selecting the Front Speakers .................................................... 13

Muting the Sound ..................................................................... 13

Listening at Night — Midnight Mode ..................................... 13

Activating the Subwoofer Sound ............................................. 14

Reinforcing the Bass ................................................................ 14

Attenuating the Input Signal .................................................... 14

Selecting the Line Direct Function .......................................... 14

Adjusting the Equalization Patterns ......................................... 15

Using the Sleep Timer .............................................................. 15

Recording a Source .................................................................. 15

7 Showing the MENU on the TV Screen ................................ 36

7 Activating the Surround Modes ............................................ 36

7 Activating the DSP Modes ................................................... 36

7 Selecting the Analog or Digital Input Mode........................... 36

7 Adjusting the Equalization Pattern ....................................... 37

7 Adjusting the Surround and DSP Modes.............................. 37

7 Adjusting the DVD MULTI Playback Mode ........................ 38

7 Listening at Night — Midnight Mode.................................. 38

7 Attenuating the Input Signal ................................................. 38

7 Selecting the Line Direct Function....................................... 39

7 Selecting the Bass Boost Function ....................................... 39

7 Activating the Subwoofer Sound .......................................... 39

7 Operating the Tuner .............................................................. 39

7 Storing the Preset Stations.................................................... 39

7 Setting the Basic Setting Items............................................. 40

Ba s ic S et t ings ........................................... 1 6

Adjusting the Front Speaker Output Balance........................... 16

Changing the Source Name ...................................................... 16

Selecting the Video Input Terminal .......................................... 16

Setting the Subwoofer Information .......................................... 17

Adjusting the Subwoofer Output Level.................................... 17

Setting the Speakers for a Surround Field................................ 17

Digital Input (DIGITAL IN) Terminal Setting ......................... 19

Selecting the Analog or Digital Input Mode ............................ 20

Showing the Text Information on the Display ......................... 21

Basic Setting and Adjustment — Auto Memory ...................... 21

COM P U LINK Rem ot e Cont r ol S ys t em ......... 4 1

TEXT COMPU LINK Remot e Cont r ol Sys t em .. 4 2

7 Showing the Disc Information on the TV Screen................. 43

7 Searching for a Disc (Only for the CD player) .................... 44

7 Entering the Disc Information .............................................. 45

AV COM P U LINK Rem ot e Cont r ol S ys t em .... 4 7

Oper a t ing J VC’s Audio/ Video Com ponent s ... 4 9

Receiving Ra dio Br oa dca s t s ........................ 2 2

Operating Audio Components .................................................. 49

Operating Video Components .................................................. 51

Tuning in Stations Manually .................................................... 22

Using Preset Tuning ................................................................. 22

Selecting the FM Reception Mode........................................... 23

Oper a t ing Ot her M a nufa ct ur er s ’ Video

Equipm ent ............................................ 5 2

Tr oubles hoot ing ......................................... 5 5

S pecifica t ions ............................................ 5 7

Download from Www.Somanuals.com. All Manuals Search And Download.

P a r t s Ident ifica t ion

Become familiar with the buttons and controls on the receiver before use.

Refer to the pages in parentheses for details.

3 4

67 8

pq w

RX-8010V AUDIO/VIDEO CONTROL RECEIVER

FM/AM TUNING

FM/AM PRESET

FM MODE

MEMORY

DGTL AUTO

DVD MULTI PRO LOGIC AUTO MUTING TUNED STEREO

DSP 3D–PHONIC MIDNIGHT MODE

ANALOG

LINEAR PCM

DIGITAL

STANDBY

SUBWFR LFE

LS RS

MASTER VOLUME

HEADPHONE DIGITAL EQ INPUT ATT ONETOUCH OPERATION

POWER

SPEAKERS

SLEEP VOLUME

SPEAKERS ON/OFF

DVD MULTI

DVD

VCR 1

VCR 2

VIDEO

TV SOUND/DBS

DIGITAL LEVEL

EQ ADJUST

INPUT

SURROUND ON/OFF

DSP MODE

ANALOG/DIGITAL MIDNIGHT MODE

LINE DIRECT

BASS BOOST

INPUT ATT

SOURCE NAME

TAPE / MD USB AUDIO FM / AM

SUBWOOFER OUT ON/OFF

EFFECT SETTING

CONTROL

USB AUDIO

VIDEO

S-VIDEO

VIDEO

L—AUDIO—R

PHONO

CDR

DOWN

SOURCE NAME

PHONES

u i o ;

Rem ot e Cont r ol

Fr ont P a nel

Display window (11)

POWER button and STANDBY lamp (11)

• SPEAKERS ON/OFF 1 button (13)

• SPEAKERS ON/OFF 2 button (13)

FM/AM TUNING 5/∞ buttons (22)

DSP MODE button and lamp (26)

FM/AM PRESET 5/∞ buttons (22, 23)

• INPUT ANALOG/DIGITAL button (20)

• INPUT ATT button (14)

FM MODE button (23)

MEMORY button (22)

Display (11)

EFFECT button (28, 31 – 34)

a. Remote control operation mode indicator

b. Signal transmission indicator

Lights up when transmitting the remote

control signal.

POWER buttons (11, 51, 52 – 54)

CATV/DBS, VCR 1, TV, AUDIO

Source selecting buttons (11)

DVD,DVDMULTI,CD,FM/AM,TV/DBS,VIDEO,

CDR, PHONO, VCR 1, VCR 2, TAPE/MD, USB

SURROUND ON/OFF button (26)

DSP MODE button (26)

CATV/DBS VCR 1

AUDIO

POWER

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

;

TV/DBS

VCR 1

VIDEO

VCR 2

TAPE/MD

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

LINE DIRECT button (14)

DIGITAL EQ button (15)

Remote sensor (10)

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

MIDNIGHT MODE button (13)

SOUND button (14, 16, 27 – 35, 49)

MUTING button (13)

CATV/DBS CONTROL button (53)

TV/VIDEO button (51, 52)

MIDNIGHT

TEST

CTRTONE LIVENESS

MODE

SOUND

MUTING

LEVEL ADJUST button (16, 17, 28 – 35)

SETTING button (16 – 19, 21)

MASTER VOLUME control (12)

LINE DIRECT button and lamp (14)

PHONES jack (13)

SUBWOOFER OUT ON/OFF button (14)

SURROUND ON/OFF button and lamp (26)

USB AUDIO terminal (9)

ENTER

SUBWFR

L/R BAL

CENTER

∗

7/P

DIGITALEQ

REAR L

REAR R

∗

RETURN

+10

100

FM MODE

MENU button (36 – 40)

CATV/DBS

CONTROL

BAL L

∗

TEXT DISPLAY button (43 – 46)

REC PAUSE button (50, 51, 53)

SLEEP button (15)

ANALOG/DIGITAL INPUT button (20)

• 10 keys for selecting preset channels (23)

• 10 keys for adjusting sound (14, 16, 27 – 35,

49)

CH/ LEVEL TV VOL

VOLUME

∗

TV/VIDEO

−

BAL R

∗

PLAY

EXIT

VIDEO input terminals (7)

(

TEXT

/REW

FF/

PAUSE

SET

MIDNIGHT MODE button (13)

Source selecting buttons and lamps (11)

DVD MULTI, DVD, VCR 1, VCR 2, VIDEO, TV

SOUND/DBS, PHONO, CD, CDR, TAPE/MD,

USB AUDIO, FM/AM

DISPLAY

REC

PAUSE

DOWN – TUNING – UP

)

CONTROL

STOP

• 10 keys for operating audio/video components

(49 – 54 )

RM-SRX8010J

A/V CONTROL RECEIVER

• LEVEL +/– buttons* (15, 27 – 35)

• BAL L and BAL R buttons* (16)

• CH +/– buttons (51 – 53)

SOURCE NAME buttons (16)

CONTROL UP 5/DOWN ∞ buttons

BASS BOOST button and lamp (14)

(

TV VOL +/– buttons (51, 52)

VOLUME +/– buttons (12)

EXIT button (36 – 40, 43 – 45)

• TUNING UP 3/DOWN 2 buttons (22, 49)

• On screen operate buttons (36 – 40, 43 – 46)

• Operating buttons for audio/video components

(49 – 54)

* These buttons function only after pressing

10 keys on the remote control which are

marked with an asterisk (*).

)

CONTROL button (50, 51)

Download from Www.Somanuals.com. All Manuals Search And Download.

Get t ing S t a r t ed

This section explains how to connect audio/ video components and speakers to the receiver, and how to connect the

power supply.

Befor e Ins t a lla t ion

Gener a l

Connect ing t he FM a nd AM Ant enna s

FM Ant enna Connect ions

• Be sure your hands are dry.

• Turn the power off to all components.

• Read the manuals supplied with the components you are going to

connect.

ANTENNA

FM 75

COAXIAL

Loca t ions

• Install the receiver in a location that is level and protected from

moisture.

EXT

LOOP

• The temperature around the receiver must be between –5˚ C and

35˚ C (23˚ F and 95˚ F).

• Make sure there is good ventilation around the receiver. Poor

ventilation could cause overheating and damage the receiver.

FM Antenna

Extend the supplied FM antenna horizontally.

ANTENNA

Ha ndling t he r eceiver

FM 75

COAXIAL

• Do not insert any metal object into the receiver.

• Do not disassemble the receiver or remove screws, covers, or

cabinet.

• Do not expose the receiver to rain or moisture.

LOOP

Outdoor FM Antenna Cable

Checking t he S upplied Acces s or ies

EXT

Check to be sure you have all of the following items, which are

supplied with the receiver.

The number in the parentheses indicates quantity of the pieces

supplied.

A. Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75 Ω

COAXIAL terminal as temporary measure.

• Remote Control (1)

B. Using the Standard Type Connector (Not Supplied)

A standard type connector should be connected to the FM 75 Ω

COAXIAL terminal.

• Batteries (2)

• AM Loop Antenna (1)

• FM Antenna (1)

Note:

If reception is poor, connect the outdoor antenna.

Before attaching a 75 Ω coaxial cable (the kind with a round wire

going to an outdoor antenna), disconnect the supplied FM antenna.

If anything is missing, contact your dealer immediately.

Download from Www.Somanuals.com. All Manuals Search And Download.

AM Ant enna Connect ions

Ba s ic connect ing pr ocedur e

Snap the tabs on the loop into the

ANTENNA

slots of the base to assemble the

AM loop.

FM 75

COAXIAL

LOOP

1 Cut, twist and remove the insulation at the end of

each speaker signal cable (not supplied).

AM Loop Antenna

EXT

2 Turn the knob counterclockwise.

3 Insert the speaker signal cable.

4 Turn the knob clockwise.

Connect ing t he fr ont s pea ker s

You can connect two pairs of front speakers (one pair to the FRONT

SPEAKERS 1 terminals, and another pair to the FRONT

SPEAKERS 2 terminals).

Outdoor single vinyl-covered wire (not supplied)

Turn the loop until you have the best reception.

Right speaker

Left speaker

FRONT SPEAKERS 1

Notes:

• If the AM loop antenna wire is covered with vinyl, remove

the vinyl by twisting it as shown in the diagram.

• Make sure the antenna conductors do not touch any other

terminals, connecting cords and power cord. This could cause poor

reception.

• If reception is poor, connect an outdoor single vinyl-covered wire to

the AM EXT terminal. (Keep the AM loop antenna connected.)

CAUTION :

SPEAKER IMPEDANCE

RIGHT

LEFT

RIGHT

LEFT

LOW

Connect ing t he S pea ker s

16 HIGH

–

You can connect the following speakers:

• Two pairs of front speakers to produce normal stereo sound.

• One pair of rear speakers to enjoy the surround effect.

• One center speaker to produce more effective surround effect (to

emphasize human voices).

SPEAKER LOAD SELECTOR

FRONT SPEAKERS

• One subwoofer to enhance the bass.

IM P ORTANT:

After connecting the speakers listed above, set the speaker

setting information properly to obtain the best possible

Surround and DSP effect. For details, see page 17.

Right speaker

FRONT SPEAKERS 2

Left speaker

For each speaker (except for a subwoofer), connect the (+) and (–)

terminals on the rear panel to the (+) and (–) terminals marked on

the speakers. For connecting a subwoofer, see page 5.

IMPORTANT:

To obtain the best possible output power from the receiver, and to

prevent the receiver from being overheated, the receiver has the

SPEAKER LOAD SELECTOR which has to be set as follows:

• Set it to “HIGH” when the impedance of the front speakers

connected is within the range of 8 Ω to 16 Ω.

• Set it to “LOW” when the impedance of the front speakers

connected is within the range of 4 Ω to 6 Ω.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the

speaker terminals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect ing t he r ea r a nd cent er s pea ker s

Ana log Connect ions

Connect rear speakers to the REAR SPEAKERS terminals and a

center speaker to the CENTER SPEAKER terminals.

Audio com ponent connect ions

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the

audio right jack.

Center speaker

CAUTION:

CENTER

SPEAKER

REAR SPEAKERS

If you connect a sound-enhancing device such as a graphic equalizer

between the source components and this receiver, the sound output

through this receiver may be distorted.

–

Turntable

AUDIO

RIGHT

LEFT

RIGHT

LEFT

Turntable

CAUTION : SPEAKER IMPEDANCE 8 16

REAR

PHONO

Right rear speaker

Left rear speaker

Turntable

Connect ing t he s ubwoofer s pea ker

OUT

(REC)

To audio output

You can enhance the bass by connecting a subwoofer.

Connect the input jack of a powered subwoofer to the

SUBWOOFER OUT jack on the rear panel, using a cable with RCA

pin plugs (not supplied).

TAPE

(PLAY)

OUT

(REC)

If an earth cable is provided for your

turntable, connect the cable to the

screw marked (H) on the rear panel.

CDR

SUBWOOFER

OUT

(PLAY)

Ex.: This connection is for the

turntable with an MM (moving-

magnet) type cartridge.

Powered subwoofer

Note:

Connect ing Audio/ Video Com ponent s

Any turntables incorporating a small-output cartridge such as an MC

(moving-coil) type must be connected to this receiver through a

commercial head amplifier or step-up transformer. Direct connection

may result in insufficient volume.

You can connect the following audio/video components to this

receiver. Refer also to the manuals supplied with your components.

Audio Components

• Turntable

Video Components

• DVD player*

• TV*

• CD player*

CD player

• Cassette deck or

MD recorder*

• DBS tuner*

• VCR(s)

AUDIO

RIGHT

LEFT

• CD recorder*

• Video camera

REAR

• Personal computer (PC)

PHONO

* You can connect these components using the methods described in

“Analog connections” (to the right), or in “Digital connections” (see

page 8).

CD player

OUT

(REC)

TAPE

(PLAY)

To audio output

OUT

(REC)

CDR

(PLAY)

Download from Www.Somanuals.com. All Manuals Search And Download.

Video com ponent connect ions

Cassette deck or MD recorder

Cassette deck

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the

audio right jack, and the yellow plug to the video jack.

• If your video components have S-video (Y/C-separation) and/or

component video (Y, P^B/CB, PR/CR) terminals, connect them using

an S-video cable (not supplied) and/or component video cable (not

supplied). By using these terminals, you can get a better picture

quality in the order — Component video > S-video > Composite

video.

To audio output

To audio input

AUDIO

RIGHT

LEFT

REAR

PHONO

IMPORTANT:

This receiver is equipped with the following video terminals —

composite video, S-video and component video terminals. You can

use any of the three to connect a video component.

OUT

(REC)

However, remember that the video signals from one type of these

input terminals are output only through the video output

terminals of the same type.

TAPE

(PLAY)

Therefore, if a recording video component and a playing video

component are connected to the receiver through the different video

terminals, you cannot record the picture from the playing component

on the recording component. In addition, if the TV and a playing video

component are connected to the receiver through the different video

terminals, you cannot view the playback picture from the playing

component on the TV.

To audio output

To audio input

Note:

MD recorder

You can connect either a cassette deck or an MD recorder to the

TAPE/MD jacks. When connecting an MD recorder to the TAPE/MD

jacks, change the source name, which will be shown on the display

when selected as the source, to “MD.” See page 16 for details.

VCR(s)

S-VHS (or VHS) VCR

C D

CD recorder

E F

VIDEO

CD recorder

AUDIO

S-VIDEO

RIGHT

LEFT

To audio output

To audio input

DVD

FRONT

TV SOUND

DBS

AUDIO

RIGHT

LEFT

OUT

(REC)

REAR

VCR1

PHONO

(PLAY)

OUT

(REC)

OUT

(REC)

VCR2

(PLAY)

TAPE

(PLAY)

MONITOR

OUT

(REC)

CDR

(PLAY)

S-VHS (or VHS) VCR

If your audio components have a COMPU LINK or TEXT

COMPU LINK jack

• See also page 41 for detailed information about the connection and

the COMPU LINK remote control system.

• See also page 42 for detailed information about the connection and

the TEXT COMPU LINK remote control system.

Å To left/right channel audio output

ı To left/right channel audio input

Ç To S-video output

Î To composite video output

‰ To composite video input

Ï To S-video input

Download from Www.Somanuals.com. All Manuals Search And Download.

TV and/or DBS tuner

Video camera

The VIDEO input terminals on the front panel are convenient when

connecting and disconnecting the equipment frequently.

When connecting the TV to the AUDIO jacks (TV SOUND/

DBS), DO NOT connect the TV’s video output to these

video input terminals.

VIDEO

S-VIDEO

VIDEO

L—AUDIO—R

VIDEO

AUDIO

S-VIDEO

DVD COMPONENT VIDEO

RIGHT

LEFT

To audio

output

DVD

FRONT

TV SOUND

DBS

To S-video output

OUT

MONITOR

OUT

To composite

video output

(REC)

VCR1

B/C

R/C

(PLAY)

OUT

(REC)

DVD player

VCR2

(PLAY)

• When you connect the DVD player with stereo output jacks:

MONITOR

OUT

Å To front left/right channel audio

COMPONENT VIDEO

DVD

output (or to audio mixed output if

necessary)

ı To composite video output

Ç To S-video output

DBS

Î To component video output

DVD player

Connect the TV to the MONITOR OUT

terminal to view the playback picture from the

other connected video components.

DVD

Å To audio output

ı To composite video input

Ç To S-video input

VIDEO

AUDIO

S-VIDEO

RIGHT

LEFT

DVD

FRONT

Î To component video input

TV SOUND

VIDEO

• When you connect the DVD player with its analog discrete output

(5.1 CH reproduction) jacks:

AUDIO

DVD COMPONENT VIDEO

S-VIDEO

RIGHT

LEFT

DVD

FRONT

Å To subwoofer output

ı To center channel audio output

Ç To rear left/right channel audio output

TV SOUND

DBS

DVD COMPONENT VIDEO

MONITOR

OUT

DBS tuner

Î To front left/right channel audio output

B/C

R/C

DBS

‰ To composite video output

DBS

Ï To S-video output

Ì To component video output

DVD player

DVD

Å To audio output

ı To composite video output

Ç To S-video output

Î To component video output

Notes:

• When connecting the DBS tuner to the TV SOUND/DBS jacks,

change the source name, which will be shown on the display when

selected as the source, to “DBS.” See page 16 for details.

• When operating the DBS tuner by using the AV COMPU LINK

remote control system, change the video input terminal setting

correctly. See pages 16 and 47 for details.

VIDEO

SUB

WOOFER

AUDIO

S-VIDEO

CENTER

RIGHT

LEFT

RIGHT

LEFT

DVD

FRONT

REAR

Note:

When operating the DVD player by using the AV COMPU LINK

remote control system, change the video input terminal setting

correctly. See pages 16 and 47 for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes:

Digit a l Connect ions

• When shipped from the factory, the DIGITAL IN terminals have

been set for use with the following components.

– DIGITAL 1 (coaxial): For DVD player

This receiver is equipped with four DIGITAL IN terminals — one

digital coaxial terminal and three digital optical terminals, and one

DIGITAL OUT terminal.

– DIGITAL 2 (optical): For CD player

– DIGITAL 3 (optical): For digital TV broadcast tuner

– DIGITAL 4 (optical): For CD recorder

IMPORTANT:

• When you want to operate the CD player, CD recorder, or MD

recorder using the COMPU LINK remote control system, connect

the target component also as described in “Analog Connections”

(see pages 5 and 6).

• When connecting the DVD player, digital TV broadcast tuner or

DBS tuner using the digital terminals, you also need to connect it to

the video terminal on the rear. Without connecting it to the video

terminal, you can view no playback picture.

• When you want to operate the DVD player using the AV COMPU

LINK remote control system, connect the DVD player also as

described in “Analog Connections” (see page 7).

• After connecting the components using the DIGITAL IN terminals,

set the following correctly if necessary.

– Set the digital input (DIGITAL IN) terminal setting correctly. For

details, see “Digital Input (DIGITAL IN) Terminal Setting” on page

19.

– Select the digital input mode correctly. For details, see “Selecting

the Analog or Digital Input Mode” on page 20.

Digital input terminals

Digital output terminal

You can connect any digital equipment as follow.

CD recorder

MD recorder

Digital TV

DBS tuner

DBS

Digital optical cable (not supplied)

between digital optical terminals

DVD player

DVD

CD player

MD recorder

CD recorder

When the digital recording

equipment such as an MD recorder

and CD recorder has a digital

optical input terminal, connecting it

to the DIGITAL OUT terminal

enables you to perform digital-to-

digital recording.

PCM/DOLBY DIGITAL

/DTS

Digital coaxial cable (not supplied)

between digital coaxial terminals

DIGITAL OUT

Digital optical cable (not supplied)

between digital optical terminals

Note:

The digital signal format output through the DIGITAL OUT terminal is

the same as that of the input signal. This means that when the DTS

Digital Surround signals are input, the DTS Digital Surround signals

are output.

When the component has a digital

coaxial output terminal, connect it to the

DIGITAL 1 (DVD) terminal, using the

digital coaxial cable (not supplied).

DIGITAL IN

When the component has a digital

optical output terminal, connect it to the

DIGITAL 2 (CD), DIGITAL 3 (TV) or

DIGITAL 4 (CDR) terminal, using the

digital optical cable (not supplied).

DIGITAL 1 (DVD)

DIGITAL 2 (CD)

DIGITAL 3 (TV)

Before connecting a digital

optical cable, unplug the

protective plug.

DIGITAL 4 (CDR)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Check if the drivers are correctly installed.

1. Open the Control Panel on your PC: Select [Start] =

[Settings] = [Control Panel]

US B Connect ion

This receiver is equipped with a USB terminal on the front panel.

You can connect your PC to this terminal and enjoy sound

reproduced through your PC.

When you connect your PC for the first time, follow the procedure

below.

2. Select [System], then [Device Manager] and click [Sound,

video and game controllers] and [Universal Serial Bus

controllers.]

The following window appears, and you can check whether

the drivers are installed.

• Remember you cannot send any signal or data to your PC from

this receiver.

IMPORTANT

• Check if your PC equipped with the CD-ROM drive is running

on Windows 98*, Windows Me*, or Windows 2000* and

prepare its CD-ROM.

• Check your PC’s BIOS setting — whether USB is available, and

whether USB IRQ is set to “AUTO” or to available IRQ number.

How to install the USB drivers

The following procedure is described using the English version of

Windows 98. If your PC is running on a different version of

Windows, the screens shown on your PC’s monitor will differ from

the ones used in the following procedure.

1. Turn on your PC and start running Windows 98, Windows

Me or Windows 2000.

Note:

If the PC has been turned on, quit all the applications now running.

The items shown on the PC’s monitor differ

depending on your PC settings.

2. Turn on the receiver, and press USB AUDIO on the front

panel or USB on the remote control.

The lamp on the USB AUDIO button lights up.

6. Change the PC audio setting.

1. If you have closed Control Panel, open it again: Select [Start]

= [Settings] = [Control Panel]

2. Click [Multimedia], then select “USB Audio Device [1]” for

“Playback” of “Audio,” and close the window.

3. Connect the receiver to the PC using a USB cable (not

supplied).

Your PC automatically recognizes this connection, and shows

the following screen on the monitor.

To play back a CD from CD-ROM drive on PC, click

[Multimedia], [CD Music] then check [Enable digital CD audio for

this CD-ROM device].

USB AUDIO

VIDEO

S-VIDEO

L—AUDIO—R

Now PC is ready for playback through the USB connection.

After installation is completed, you can use your PC as the playback

source. The PC automatically recognizes the receiver whenever a

USB cable is connected between the PC and the receiver while the

receiver is turned on.

USB cable

• When not using the PC as the playback source, disconnect the

USB cable.

To play back sounds on the PC, refer to the manuals supplied with

the sound reproduction application installed in the PC.

Notes:

• DO NOT turn off the receiver or disconnect the USB cable while

installing the drivers and for a several seconds each time your PC is

recognizing the receiver.

• Use a full speed USB cable (revision 1.0).

• If your PC does not recognize the receiver, disconnect the USB

cable and connect it again. If this does not work, restart Windows.

• The drivers installed can be recognized only when the USB cable is

connected between the receiver and your PC.

• The sound may not be played back correctly — interrupted or

degraded — due to your PC settings and PC specifications.

4. Install the USB drivers following the instructions on the PC’s

monitor.

* Microsoft , Windows 98, Windows Me and Windows 2000 are

registered trademarks of Microsoft corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

P ut t ing Ba t t er ies in t he Rem ot e Cont r ol

Connect ing t he P ower Cor d

Before using the remote control, put two supplied batteries first.

When using the remote control, aim the remote control directly at

the remote sensor on the receiver.

Before plugging the receiver into an AC outlet, make sure that all

connections have been made.

Plug the power cord into an AC outlet.

1. On the back of the remote control, remove the

battery cover.

Keep the power cord away from the connecting cables and the

antenna. The power cord may cause noise or screen interference. We

recommend that you use a coaxial cable to connect the antenna,

since it is well-shielded against interference.

2. Insert batteries. Make sure to match the

polarity: (+) to (+) and (–) to (–).

Note:

The preset settings such as preset channels and sound adjustment

may be erased in a few days in the following cases:

R6P(SUM-3)/AA(15F)

– When you unplug the power cord.

– When a power failure occurs.

CAUTIONS:

• Do not touch the power cord with wet hands.

• Do not pull on the power cord to unplug the cord. When

unplugging the cord, always grasp the plug so as not to damage

the cord.

3. Replace the cover.

If the range or effectiveness of the remote control decreases, replace

the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

Note:

After replacing the batteries, set the manufacturers’ codes again (see

page 52).

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

• Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

• Use the correct type of batteries. Batteries that look similar may

differ in voltage.

• Always replace both batteries at the same time.

• Do not expose batteries to heat or flame.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ba s ic Oper a t ions

The following operations are commonly used when you play any sound source.

Fr om t he r em ot e cont r ol:

Befor e us ing t he r em ot e cont r ol

AUDIO

To turn on the power, press AUDIO POWER.

The STANDBY lamp on the front panel goes off.

The name of the current source and Surround/DSP

mode appear on the display.

How to confirm the remote control operation mode

POWER

The display window on the remote control shows following

information for about 10 seconds when you press certain buttons on

the remote control, so that you can confirm which operation you do.

To turn off the power (into standby mode), press AUDIO POWER

again. The STANDBY lamp on the front panel lights up.

Pressing one of the source selecting buttons,

the source name selected appears on the

display.

Buttons

FM/AM

Indications

TUNER

PHONO

TAPE

DVD

S elect ing t he S our ce t o P la y

Press one of the source selecting buttons.

The lamp on the front panel button for selected source lights up.

• The selected source name and Surround/DSP mode also appear on

the display.

PHONO

TAPE/MD

DVD or DVD MULTI

CDR

Ex.: When you

press CD.

CDR

USB

TV/DBS

VCR 1

VCR 2

On t he fr ont pa nel:

VCR 1

VCR 2

VIDEO

DVD MULTI

DVD

VCR 1

VCR 2

VIDEO

TV SOUND/DBS

VIDEO

SOURCE NAME

FM / AM

PHONO

CDR

TAPE / MD

USB AUDIO

Pressing SOUND before you adjust the sound

effect, “SOUND” appears on the display.

SOURCE NAME

Fr om t he r em ot e cont r ol:

Pressing TEXT DISPLAY or MENU before

you use on-screen menu or TEXT COMPU

LINK, “MENU” appears on the display (see

pages 36 and 42).

DVD

TV/DBS

VCR 1

DVD MUILTI

FM/AM

VIDEO

CDR

PHONO

USB

VCR 2

TAPE/MD

Pressing CONTROL or CATV/DBS

CONTROL before you operate an audio or

video equipment connected to the receiver,

the remote control operation mode selected

appears on the display (see pages 49 and 52).

Ex.: When you

press CATV/

DBS CONTROL.

Selected source name and current

Surround/DSP mode appear

DGTL AUTO

DVD MULTI PRO LOGIC AUTO MUTING TUNED STEREO

ANALOG

LINEAR PCM

DIGITAL

DSP 3D–PHONIC MIDNIGHT MODE

SUBWFR LFE

LS RS

HEADPHONE DIGITAL EQ INPUT ATT ONETOUCH OPERATION

Tur ning t he P ower On a nd Off (S t a ndby)

SPEAKERS

SLEEP VOLUME

On t he fr ont pa nel:

STANDBY

To turn on the power, press POWER.

The STANDBY lamp goes off. The name of the

current source and Surround/DSP mode appear

on the display.

POWER

DVD MULTI

Select the DVD player for viewing the digital

video disc using the analog discrete output mode

(5.1CH reproduction).

To enjoy the DVD MULTI playback, see page 35.

Select the DVD player.

Select the video component connected to the

VCR 1 terminals.

Current source name and

Surround/DSP mode appear

DVD

VCR 1

ANALOG

VCR 2

VIDEO

Select the video component connected to the

VCR 2 terminals.

Select video component connected to the

VIDEO terminals.

SPEAKERS

VOLUME

Current volume level appears

TV (SOUND)/DBS Select TV sounds (or the DBS tuner).

PHONO ^*

CD ^*

Select the turntable.

Select the CD player.

Select the CD recorder.

Select the cassette deck (or the MD recorder).

Select the personal computer (PC) connected

to the USB terminal.

Select an FM or AM broadcast.

• Each time you press the button, the band

alternates between FM and AM.

To turn off the power (into standby mode),

press POWER again.

The STANDBY lamp lights up. A small amount

of power is consumed in standby mode. To turn

the power off completely, unplug the AC power

cord.

STANDBY

CDR ^*

POWER

TAPE/MD ^*

USB (AUDIO) ^*

FM/AM ^*

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes:

On t he fr ont pa nel:

DVD MULTI

TV SOUND/DBS

DVD

VCR 1

VCR 2

VIDEO

• When connecting an MD recorder (to the TAPE/MD jacks), and a

DBS tuner (to the TV SOUND/DBS jacks), change the source

names shown on the display. For details, see page 16.

• When you press one of the source selecting buttons on the remote

control marked with an asterisk (*), the receiver automatically turns

on.

SOURCE NAME

FM / AM

PHONO

CDR

TAPE / MD

USB AUDIO

SOURCE NAME

Fr om t he r em ot e cont r ol:

S igna l a nd s pea ker indica t or s on t he dis pla y

The signal indicators light up in the following cases:

• Only the indicators for the incoming signals light up.

• When analog input is selected, “L” and “R” always light up.

• When “DVD MULTI” is selected as the source, “L,” “C,” “R,”

“LFE,” “LS” and “RS” light up.

DVD

TV/DBS

VCR 1

DVD MUILTI

VIDEO

CDR

FM/AM

PHONO

USB

VCR 2

TAPE/MD

The speaker indicators light up only —:

The frames of “C,” “LS,” and “RS” light up, when the

corresponding speaker is set to “LARGE” or “SMALL”.

Note:

Once you have selected a video source, pictures of the selected

source are sent to the TV until you select another video source.

Signal indicators light up in

red:

Speaker indicators light up

in white:

Adjus t ing t he Volum e

SUBWFR LFE

On t he fr ont pa nel:

MASTER VOLUME

To increase the volume, turn MASTER

VOLUME clockwise.

To decrease the volume, turn it

counterclockwise.

• When you turn MASTER VOLUME rapidly,

the volume level also changes rapidly.

• When you turn MASTER VOLUME slowly,

the volume level also changes slowly.

• When digital input is selected: Lights up when the left

channel signal comes in.

• When analog input is selected: Always lights up.

• When digital input is selected: Lights up when the right

channel signal comes in.

• When analog input is selected: Always lights up.

Lights up when the center channel signal comes in.

Lights up when the left rear channel signal comes in.

Fr om t he r em ot e cont r ol:

LS:

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

RS: Lights up when the right rear channel signal comes in.

S: Lights up when the monaural rear channel signal comes in.

LFE: Lights up when the LFE channel signal comes in.

VOLUME

−

CAUTION:

Note:

Always set the volume to the minimum before starting any source. If

the volume is set at its high level, the sudden blast of sound energy

can permanently damage your hearing and/or ruin your speakers.

SUBWFR

When “SUBWOOFER” is set to “YES,”

17).

lights up (see page

Notes:

S elect ing differ ent s our ces for pict ur e a nd

s ound

• The volume level can be adjusted within the range of “0” (minimum)

to “90” (maximum).

You can watch picture from a video component while listening to

sound from another component.

• If you set One Touch Operation to “ON” (see page 21), you do not

have to adjust the volume level each time you change the source. It

is automatically set to the stored level.

Press one of the audio source selecting buttons — PHONO, CD,

CDR, TAPE/MD, USB(AUDIO), FM/AM — while viewing the

picture from a video component such as the VCR or DVD player,

etc.

The lamp on the front panel button for selected source lights up.

Download from Www.Somanuals.com. All Manuals Search And Download.

S elect ing t he Fr ont S pea ker s

M ut ing t he S ound

IMPORTANT:

Fr om t he r em ot e cont r ol ONLY:

MUTING

You can activate two pairs of the front speakers at the same time only

when the SPEAKER LOAD SELECTOR switch on the rear panel is

set to “HIGH” and when no signals are sent to the center and rear

speakers. Otherwise, activating one pair of the speakers deactivates

the other.

Press MUTING to mute the sound through all

speakers and headphones connected.

“MUTING” appears on the display and the

volume turns off (the volume level indicator goes

off).

To restore the sound, press MUTING again so that “MUTING

OFF” appears on the display.

• Turning MASTER VOLUME on the front panel or pressing

VOLUME +/– on the remote control also restores the sound.

On t he fr ont pa nel ONLY:

When you have connected two pairs of the front speakers, you can

select which to use.

To use the speakers connected to the

SPEAKERS ON/OFF

FRONT SPEAKERS 1 terminals, press

SPEAKERS ON/OFF 1 so that SPEAKERS 1

indicator lights up on the display. Make sure

that the SPEAKERS 2 is not lit on the display.

Lis t ening a t Night — M idnight M ode

Using the midnight mode, you can enjoy a powerful sound at night

even at a low volume level.

• You can do this setting for each source.

To use the speakers connected to the FRONT SPEAKERS 2

terminals, press SPEAKERS ON/OFF 2 so that SPEAKERS 2

indicator lights up on the display. Make sure that the SPEAKERS 1

Press MIDNIGHT MODE to select the midnight mode.

is not lit on the display.

MIDNIGHT

MODE

MIDNIGHT MODE

To use both sets of the speakers, press SPEAKERS ON/OFF 1 and

2 so that the SPEAKERS 1 and SPEAKERS 2 indicators light up on

the display.

On the front panel

To use neither sets of the speakers, press SPEAKERS ON/OFF 1

From the remote control

and 2 so that the SPEAKERS 1 and SPEAKERS 2 indicators

• Each time you press the button, the midnight mode changes as

follow.

disappear from the display.

The HEADPHONE indicator lights up and “HEADPHONE”

appears on the display.

• Activating the speaker turns on the Surround and DSP modes

previously selected.

MIDNIGHT 1

MIDNIGHT 2

NORMAL

• Listening only with headphones:

MIDNIGHT 1: Select this when you want to compress the

dynamic range a little.

You can listen with the headphones without deactivating both

pairs of speakers by connecting a pair of headphones to the

PHONES jack on the front panel. If you want to use a pair of

headphones without outputting sounds from the front speakers,

you must turn off both pairs of the front speakers as mentioned

above.

The MIDNIGHT MODE indicator lights up on the

display.

MIDNIGHT 2: Select this when you want to compress the

dynamic range fully. (Useful at midnight).

The MIDNIGHT MODE indicator lights up on the

display.

Notes:

NORMAL:

Select this when you want to enjoy sound with its

full dynamic range. (No effect applied.)

The MIDNIGHT MODE indicator goes off from

the display.

• If you use any of the Surround and DSP modes using the center or

rear speakers with both front speakers activated, the speakers

connected to the FRONT SPEAKERS 2 terminals are deactivated.

• When you use HEADPHONE DSP mode, you can enjoy spacious

stereo effect. (see page 25).

Notes:

• When the line direct function is turned on, the midnight mode is

canceled temporarily.

• The midnight mode is not valid for the DVD MULTI playback mode.

CAUTION:

Be sure to turn down the volume before connecting or putting on

headphones, as high volume can damage both the headphones and

your hearing.

Download from Www.Somanuals.com. All Manuals Search And Download.

At t enua t ing t he Input S igna l

Act iva t ing t he S ubwoofer S ound

When the input level of the playing source is too high, the sounds

will be distorted. If this happens, you need to attenuate the input

signal level to prevent the sound distortion.

You can cancel the subwoofer sound even though you have

connected a subwoofer and have set “SUBWOOFER” to “YES”

(see page 17). This is useful when enjoying surround sound at night.

• You can do this setting for each source.

On t he fr ont pa nel ONLY:

Press and hold INPUT ATT (INPUT

ANALOG/DIGITAL) so that the INPUT ATT

indicator lights up on the display.

• Each time you press and hold the button, the

input attenuator mode turns on (“ATT ON”) or

off (“NORMAL”).

Press SUBWOOFER OUT ON/OFF to

SUBWOOFER OUT ON/OFF

INPUT

cancel the subwoofer sound output.

Each time you press the button, the subwoofer

sound output is deactivated (“SUBWFR OFF”)

or activated (“SUBWFR ON”).

– Select “SUBWFR OFF” to deactivate the subwoofer sound

output.

ANALOG/DIGITAL

INPUT ATT

– Select “SUBWFR ON” to activate it.

Notes:

• This function is available only for the sources connected using the

analog terminals.

• When selecting “DVD MULTI” as the source, this effect does not

work.

Note:

You cannot select “SUBWFR OFF” even though “SUBWOOFER” is

set to “YES,” when “SMALL” is selected for the front speakers (see

page 17.)

Reinfor cing t he Ba s s

S elect ing t he Line Dir ect Funct ion

You can boost the bass level.

• You can do this setting for each source.

You can enjoy the sound closer to original source by skipping the

sound adjustments such as digital equalization and midnight mode.

Only the volume level is adjustable when the line direct function is

turned on.

On t he fr ont pa nel:

BASS BOOST

Press BASS BOOST to select the bass boost

• You can do this setting for each source.

function.

The BASS BOOST lamp on the front panel button

lights up.

Press LINE DIRECT.

The LINE DIRECT lamp on the front panel button lights up.

• Each time you press the button, the bass boost

function turns on (“BOOST ON”) and off

(“BOOST OFF”).

LINE DIRECT

– Select “BOOST ON” to activate the bass boost function.

The BASS BOOST lamp on the front panel button lights up.

– Select “BOOST OFF” to cancel it.

The BASS BOOST lamp on the front panel button goes off.

On the front panel

From the remote control

• Each time you press the button, the line direct function turns on

(“DIRECT ON”) and off (“DIRECT OFF”).

– Select “DIRECT ON” to activate the line direct function.

The LINE DIRECT lamp on the front panel button lights up.

– Select “DIRECT OFF” to cancel it.

Fr om t he r em ot e cont r ol:

SOUND

1. Press SOUND.

The 10 keys are activated for sound

adjustments.

The LINE DIRECT lamp on the front panel button goes off.

BASS

BOOST

2. Press BASS BOOST to select the bass

Notes:

boost function.

The BASS BOOST lamp on the front panel

button lights up.

• If you turn on the line direct function while using the Surround and

DSP modes, the effect changes as follows:

• Each time you press the button, the bass boost function turns

on (“BOOST ON”) and off (“BOOST OFF”).

–Select “BOOST ON” to activate the bass boost function.

The BASS BOOST lamp on the front panel button lights up.

–Select “BOOST OFF” to cancel it.

Mode

Surround

DSP

Input

Analog

Digital

Not valid

Valid

Not valid

• Turning off the line direct function activates the sound adjustments

previously selected such as the digital equalization and midnight

mode.

The BASS BOOST lamp on the front panel button goes off.

Note:

This function does not affect the sounds outputting from the rear

speakers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjus t ing t he Equa liza t ion P a t t er ns

Us ing t he S leep Tim er

You can adjust equalization to your preference.

• You can do this setting for each source.

Using the Sleep Timer, you can fall asleep to music and know the

receiver will turn off by itself rather than play all night.

Before you start, remember....

Fr om t he r em ot e cont r ol ONLY:

SLEEP

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

Press SLEEP repeatedly.

The SLEEP indicator lights up on the display, and

the shut-off time changes as follows (in minutes):

On t he fr ont pa nel:

1. Press DIGITAL EQ (Equalization)

DIGITAL LEVE

10 20 30 40 50 60 70 80 90

ADJU

repeatedly to select the frequency.

• Each time you press the button, the frequency

with its current level changes as follows:

(Canceled)

When the shut-off time comes

The receiver turns off automatically.

EQ1kHz

EQ63Hz

EQ250Hz

and its level

EQ16kHZ

EQ4kHz

To check or change the time remaining until the shut-off time

Press SLEEP once.

and its level

2. Press CONTROL UP 5/DOWN ∞

repeatedly to adjust the frequency level.

The frequency level changes by 2 dB from

–8 dB to +8 dB. The DIGITAL EQ indicator

lights up on the display.

CONTROL

The remaining time until the shut-off time appears in minutes.

• To change the shut-off time, press SLEEP repeatedly.

DOWN

To cancel the Sleep Timer

Press SLEEP repeatedly until “SLEEP 0min” appears on the display.

(The SLEEP indicator goes off.)

• Turning off the power also cancels the Sleep Timer.

3. Repeat Steps 1 and 2 to adjust the other frequency level.

To flat the equalization pattern,

Set all the frequency levels to “0” in step 2. The DIGITAL EQ

indicator goes off from the display.

Recor ding a S our ce

For analog-to-analog recording

Fr om t he r em ot e cont r ol:

You can record any analog source through the receiver to —

• the cassette deck (or MD recorder) connected to the TAPE/MD

jacks,

SOUND

1. Press SOUND.

The 10 keys are activated for sound adjustments.

• the VCRs connected to the VCR 1 and VCR 2 jacks, and

• the CD recorder connected to the CDR jacks

— at the same time.

2. Press DIGITAL EQ (Equalization)

DIGITALEQ

∗

repeatedly to select the frequency you want.

“EQ” appears on the remote control display

RETURN

For digital-to-digital recording

window.

• Each time you press the button, the frequency with its level

changes as follows:

You can record the currently selected digital input source through

the receiver to a digital recording device connected to the DIGITAL

OUT terminal.

EQ1kHz

EQ63Hz

EQ250Hz

and its level

Notes:

EQ16kHZ

EQ4kHz

• Analog-to-digital and digital-to-analog recordings are not possible.

• The output volume level, midnight mode (see page 13), bass boost

(see page 14), digital equalization (see the left), Surround modes

and DSP modes (see page 24) cannot affect the recording.

• The test tone signal (see page 27) does not come out through the

DIGITAL OUT terminal.

and its level

3. Press LEVEL + or − repeatedly to adjust

the frequency level.

BAL L

∗

The frequency level changes by 2 dB from

–8 dB to +8 dB. The DIGITAL EQ indicator

lights up on the display.

CH/ LEVEL

∗

−

BAL R

∗

4. Repeat steps 2 and 3 to adjust the other

frequency level.

To flat the equalization pattern,

Set all the frequency levels to “0” in step 3. The DIGITAL EQ

indicator goes off from the display.

Notes:

• When the line direct function is turned on, the digital equalization

cannot be adjusted.

• The digital equalization affects the front speaker sounds only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ba s ic S et t ings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while

others will make operations easier.

When changing the source name from “TV” to

Adjus t ing t he Fr ont S pea ker Out put

Ba la nce

“DBS”:

TV SOUND/DBS

• Press and hold SOURCE NAME (TV

SOUND/DBS) until “ASSGN. DBS”

appears on the display.

If the sounds you hear from the front right and left speakers are

unequal, you can adjust the speaker output balance.

• You can do this setting for each source.

SOURCE NAME

To change the source name to “TAPE” or “TV,” repeat the same

procedure above — press and hold SOURCE NAME (TAPE/MD)

to select “TAPE,” or press and hold SOURCE NAME (TV

SOUND/DBS) to select “TV.”

Before you start, remember....

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On t he fr ont pa nel:

Note:

LEVEL

ADJUST

1. Press LEVEL ADJUST repeatedly

until “BAL– (with current

Without changing the source name, you can still use the connected

components. However, there may be some inconvenience.

– “TAPE” or “TV” will appear on the display when you select the MD

recorder or DBS tuner.

setting)” appears on the display.

– You cannot use the digital input (see page 19) for the MD recorder.

– You cannot use the COMPU LINK remote control system (see page

41) to operate the MD recorder.

CONTROL

DOWN UP

2. Press CONTROL UP 5/DOWN ∞

to adjust the balance.

• Pressing CONTROL UP 5 decreases the

left channel output (from CENTER to

L–21).

• Pressing CONTROL DOWN ∞ decreases the

right channel output (from CENTER to R–21).

S elect ing t he Video Input Ter m ina l

This receiver is equipped with the component video input terminals

for the DVD player and DBS tuner, which give you higher picture

quality. When you use the component video input terminals for the

DVD player and/or DBS tuner, change the video input terminal

setting.

Fr om t he r em ot e cont r ol:

SOUND

1. Press SOUND.

The 10 keys are activated for sound

adjustments.

Before you start, remember....

2. Press L/R BAL.

“L/R” appears on the remote control display

window.

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

L/R BAL

∗

On t he fr ont pa nel ONLY:

3. Press BAL L or BAL R to adjust

the balance.

1. Press SETTING repeatedly until

CT SETTING

BAL L

∗

“VIDEO DVD” or “VIDEO DBS”

appears on the display.

The display changes to show the current setting.

• Select “VIDEO DVD” to select the video input terminal for

the DVD player and “VIDEO DBS” for the DBS tuner.

• Pressing BAL L decreases the right

CH/ LEVEL

∗

channel output (from CENTER to R–21).

• Pressing BAL R decreases the left channel

output (from CENTER to L–21).

−

BAL R

∗

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select the appropriate video

Cha nging t he S our ce Na m e

input terminal.

• Each time you press the button, the display

changes to show the following:

When you have connected an MD recorder to the TAPE/MD jacks

or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,

change the source name which will be shown on the display when

you select the MD recorder or DBS tuner as the source.

COMPNT

(Component)

S/C

(S-video/Composite)

On t he fr ont pa nel ONLY:

COMPNT: Select this when you connect the DVD player or

DBS tuner to the component video input terminals.

When changing the source name from “TAPE” to

“MD”:

S/C:

Select this when you connect the DVD player or DBS

tuner to the composite video or S-video input terminal.

• Press and hold SOURCE NAME

TAPE / MD

(TAPE/MD) until “ASSGN. MD”

appears on the display.

Note:

SOURCE NAME

Without changing the video input terminal setting, you can see the

picture through the video input terminals, but cannot use the AV

COMPU LINK remote control system correctly (see page 47).

Download from Www.Somanuals.com. All Manuals Search And Download.

S et t ing t he S pea ker s for a S ur r ound

Field

S et t ing t he S ubwoofer Infor m a t ion

To obtain the best possible surround sound of the Surround and DSP

modes, you have to register the information about the speakers

arrangement after all connections are completed.

Before you start, remember....

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

Before you start, remember....

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On t he fr ont pa nel ONLY:

CT SETTING

1. Press SETTING repeatedly until

“SUBWOOFER” appears on the

display.

Fr ont , Cent er, a nd Rea r S pea ker S et t ing

• When you change your speakers, you need to register the

information about the speakers again.

The display changes to show the current setting.

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select “YES” or “NO.”

On t he fr ont pa nel ONLY:

• Each time you press the button, the display

alternates between “YES” and “NO.”

CT SETTING

1. Press SETTING repeatedly until

“FRONT SPK” (Front Speaker),

“CTR SPK” (Center Speaker) or

“REAR SPK” (Rear Speaker)

appears on the display.

YES:

NO:

Select this when a subwoofer is connected.

Select this when no subwoofer is used.

The display changes to show the current setting.

Note:

You cannot use SUBWOOFER OUT ON/OFF on the front panel (see

page 14) and adjust the subwoofer output level (see below) when

“SUBWOOFER” is set to “NO.”

2. Press CONTROL UP 5/DOWN ∞

CONTROL

DOWN

to select the appropriate item

about the speaker selected in the

above step.

• Each time you press the button, the display

Adjus t ing t he S ubwoofer Out put Level

changes to show the following:

You can adjust the subwoofer output level if you have selected

“YES” for the “SUBWOOFER” (see above).

Once it has been adjusted, the receiver memorizes the adjustment.

• You can do this setting for each source.

LARGE

SMALL

NONE

Before you start, remember....

LARGE: Select this when the speaker size is relatively large.

SMALL: Select this when the speaker size is relatively small.

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• When the front speakers are all deactivated, the subwoofer level

cannot be adjusted.

NONE: Select this when you have not connected a speaker.

(Not selectable for the front speakers)

On t he fr ont pa nel:

3. Repeat steps 1 and 2 to select the appropriate

items for the other speakers.

AL LEVEL

1. Press LEVEL ADJUST repeatedly until

ADJUST

“SUBWFR” appears on the display.

The display changes to show the current setting.

Notes:

CONTROL

• Keep the following comment in mind as reference when adjusting.

– If the size of the cone speaker unit built in your speaker is greater

than 4 ³/4 inches (12 cm), select “LARGE,” and if it is smaller than

4 ³/4 inches (12 cm), select “SMALL.”

• If you have selected “NO” for the subwoofer setting, you can only

select “LARGE” for the front speaker setting.

2. Press CONTROL UP 5/DOWN ∞

DOWN

to adjust the subwoofer output level

(from –20 dB to +10 dB).

Fr om t he r em ot e cont r ol:

SOUND

• If you have selected “SMALL” for the front speaker setting, you

cannot select “LARGE” for the center and rear speaker settings.

1. Press SOUND.

The 10 keys are activated for sound adjustments.

SUBWFR

∗

2. Press SUBWFR .

“S-WFR” appears on the remote control display

window.

7/P

BAL L

∗

3. Press LEVEL +/– to adjust the

subwoofer output level (from –20 dB

to +10 dB).

CH/ LEVEL

∗

−

BAL R

∗

Download from Www.Somanuals.com. All Manuals Search And Download.

Cent er Dela y Tim e S et t ing

Center

comparing to that of the sound from the front speakers.

If the distance from your listening point to the center speaker is

equal to that to the front speakers, select 0 ms. As the distance to the

center speaker becomes shorter, increase the delay time.

• 1 msec increase (or decrease) in delay time corresponds to 11 ¹³/16

inches (30 cm) decrease (or increase) in distance.

speaker

Right front

speaker

Left front

speaker

3.0 m

2.7 m

• When shipped from the factory, the delay time is set to 0 ms.

2.4 m

2.1 m

On t he fr ont pa nel ONLY:

1. Press SETTING repeatedly until

CT SETTING

“CTR DELAY” (Center Delay)

appears on the display.

The display changes to show the current setting.

Left rear

speaker

Right rear

speaker

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select the delay time of the

center speaker output (from 0 ms

to 5 ms).

Ex.Set the center delay time to “1 ms” and the rear

delay time to “2 ms.”

Notes:

Cr os s over Fr equency S et t ing

• Center delay time is not valid for the DVD MULTI playback mode.

• You cannot adjust the center delay time when you have set “CTR

SPK” to “NONE.”

Small speakers cannot reproduce the bass sound very well. So, if

you have used a small speaker for any of the front, center, and rear

channels, this receiver automatically reallocates the bass elements,

originally assigned to the channel for which you have connected the

small speaker, to another channel (for which you have connected the

large speaker).

To use this function properly, you need to set the crossover

frequency level according to the size of the small speaker connected.

• If you have selected “LARGE” for all speakers (see page 17), this

function cannot be adjusted.

Rea r Dela y Tim e S et t ing

comparing to that of the sound from the front speakers.

If the distance from your listening point to the rear speakers is equal

to that to the front speakers, select 0 ms. As the distance to the rear

speakers becomes shorter, increase the delay time.

• 1 msec increase (or decrease) in delay time corresponds to 11 ¹³/16

inches (30 cm) decrease (or increase) in distance.

On t he fr ont pa nel ONLY:

• Rear delay time for Dolby Digital and DTS Digital Surround is to

be set to 5 ms.

• When shipped from the factory, the delay time is set to 5 ms.

1. Press SETTING repeatedly until

ECT SETTING

“CROSS OVER” appears on the

display.

The display changes to show the current setting.

On t he fr ont pa nel ONLY:

1. Press SETTING repeatedly until

CONTROL

ECT SETTING

2. Press CONTROL UP 5/DOWN ∞

“REAR DELAY” appears on the

display.

The display changes to show the current

setting.

DOWN

to select the crossover frequency

level according to the size of the

small speaker connected.

• Each time you press the button, the display

CONTROL

changes to show the following:

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select the delay time of the rear

speaker output (from 0 ms to

15 ms).

80Hz

100Hz

120Hz

• Use the following comments as reference when adjusting.

Notes:

80Hz:

Select this when the cone speaker unit built in the

speaker is about 4 ³/4 inches (12 cm).

• Rear delay time is not valid for the DVD MULTI playback mode.

• You cannot adjust the rear delay time when you have set “REAR

SPK” to “NONE.”

100Hz:

120Hz:

Select this when the cone speaker unit built in the

speaker is about 3 ¹⁵/16 inches (10 cm).

Select this when the cone speaker unit built in the

speaker is about 3 ³/16 inches (8 cm).

Note:

Crossover frequency is not valid for the DVD MULTI playback,

5 CH /4 CH Stereo, 3D-PHONIC, and HEADPHONE DSP modes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Low Fr equency Effect At t enua t or S et t ing

To s et t he DIGITAL 2 / 3 / 4 t er m ina ls :

If the bass sound is distorted while playing back a source using

Dolby Digital or DTS Digital Surround, follow the procedure below.

1. Press SETTING again until

DIGITAL 2/3/4 terminals' setting

appears on the display.

SETTING

On t he fr ont pa nel ONLY:

The display changes to show the current settings.

CT SETTING

1. Press SETTING repeatedly until

DIGITAL 2 terminal setting

“LFE ATT” (Low Frequency

Effect Attenuator) appears on the

display.

The display changes to show the current setting.

CONTROL

DIGITAL 3 terminal setting

2. Press CONTROL UP 5/DOWN ∞

DIGITAL 4 terminal setting

DOWN

to select the low frequency effect

CONTROL

attenuator level.

2. Press CONTROL UP 5/DOWN ∞

DOWN

• Each time you press the button, the display

to select the appropriate digital

changes to show the following:

terminal settings.

• Each time you press the buttons, the

0dB

10dB

display changes to show the following:

0dB:

Normally select this.

Select this when the bass sound is distorted.

When the DGTL COAX (DIGITAL 1) is set to “DVD”

10dB:

2: CD 3: TV (or DBS* ) 4: CDR “

2: CD 3: TV (or DBS* ) 4: MD** “

2: CD 3: MD** 4: CDR “

2: MD** 3: TV (or DBS* ) 4: CDR “

(back to the beginning)

Notes:

• Low frequency effect attenuator is not valid for the DVD MULTI

playback mode.

• This function takes effect only when the Dolby Digital or DTS Digital

Surround sounds with LFE signal comes in (with “SUBWOOFER”

set to “YES”).

When the DGTL COAX (DIGITAL 1) is set to “MD”**

2: CD 3: TV (or DBS*) 4: DVD “

2: CD 3: DVD 4: CDR “

2: DVD 3: TV (or DBS*) 4: CDR “

2: CD 3: TV (or DBS*) 4: CDR “

(back to the beginning)

Digit a l Input (DIGITAL IN) Ter m ina l

S et t ing

When the DGTL COAX (DIGITAL 1) is set to “CDR”

When you use the digital input terminals, you have to register what

components are connected to which terminals (DIGITAL IN 1/2/3/4).

2: MD** 3: TV (or DBS*) 4: DVD “

2: CD 3: TV (or DBS*) 4: DVD “

2: CD 3: TV (or DBS*) 4: MD** “

2: CD 3: MD** 4: DVD “

Before you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

(back to the beginning)

When the DGTL COAX (DIGITAL 1) is set to “TV” or “DBS”

On t he fr ont pa nel ONLY:

2: CD 3: MD** 4: CDR “ 2: MD** 3: DVD 4: CDR “

2: CD 3: DVD 4: CDR “ 2: CD 3: DVD 4: MD**

(back to the beginning)

“

To s et t he DIGITAL 1 t er m ina l:

1. Press SETTING repeatedly until

CT SETTING

“DGTL COAX” (Digital Coaxial)

appears on the display.

The display changes to show the current setting

for DIGITAL 1 terminal.

When the DGTL COAX (DIGITAL 1) is set to “CD”

2: DVD 3: TV (or DBS*) 4: MD** “

2: DVD 3: MD** 4: CDR “

2: MD** 3: TV (or DBS*) 4: CDR “

2: DVD 3: TV (or DBS*) 4: CDR “

(back to the beginning)

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select the appropriate digital

* If you have changed the source name from “TV” to “DBS,”

“DBS” appears (see page 16).

** Change the source name to “MD” for TAPE/MD jacks when you

use an MD recorder (see page 16).

terminal setting.

• Each time you press the button, the display

changes to show the following:

1: DVD “ 1: MD** “ 1: CDR “ 1 : TV (or DBS* ) “

1: CD “ (back to the beginning)

Note:

When shipped from the factory, the DIGITAL IN terminals have been

set for use with the following components.

• DIGITAL 1 (coaxial): For DVD player

• DIGITAL 2 (optical): For CD player

• DIGITAL 3 (optical): For digital TV broadcast tuner

• DIGITAL 4 (optical): For CD recorder

* If you have changed the source name from “TV” to “DBS,”

“DBS” appears (see page 16).

** Change the source name to “MD” for TAPE/MD jacks when you

use an MD recorder (see page 16).

Download from Www.Somanuals.com. All Manuals Search And Download.

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, “DGTL AUTO” may not work properly

and the following symptoms may occur:

S elect ing t he Ana log or Digit a l Input

M ode

• Sound does not come out at the beginning of playback.

• Noise comes out while using the searching or skipping

chapters or tracks.

When you have connected digital source components using the

digital terminals (see page 8), you need to change the input mode for

these components to the appropriate digital input mode correctly —

DGTL AUTO, DGTL DTS, or DGTL D.D.

CONTROL

DOWN

In this case press CONTROL UP 5/

DOWN ∞ to select “DGTL D.D” or “DGTL

DTS” while “DGTL AUTO” still remains

on the display.

Before you start, remember...

• The digital input (DIGITAL IN) terminal setting should be

correctly done for the sources you want to select the digital

input mode for. Without setting this digital input terminal

correctly, you cannot change the input mode from analog input to

digital input even if you follow the procedure below.

• Each time you press the button, the input

mode changes as follows.

DGTL AUTO

DGTL D.D

(Digital Dolby Digital)

(Digital)

DGTL DTS

On t he fr ont pa nel:

(Digital)

When selecting “DGTL D.D” or “DGTL DTS,” following

indicators showing detected signals light up on the display.

1. Press one of the source selecting button (DVD, TV

SOUND/DBS, CD, CDR, or TAPE/MD)* for which

you want to change the input mode.

: Always lights up.

The lamp on the front panel button for selected source lights up.

When selecting “DGTL D.D”

DVD MULTI

DVD

VCR 2

VIDEO

TV SOUND/DBS

VCR 1

: • Lights up when Dolby Digital signals come in.

DIGITAL

• The frame flashes when Dolby Digital signals

are not recognized.

SOURCE NAME

FM / AM

PHONO

CDR

TAPE / MD

USB AUDIO

When selecting “DGTL DTS”

: • Lights up when DTS Digital Surround signals come in.

SOURCE NAME

• The frame flashes when DTS Digital Surround

signals are not recognized.

Note:

* Among the source listed above, you can select the digital input

only for the sources which you have selected the digital input

terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting”

on page 19.)

Note:

When you turn off the power or select another source, “DGTL

D.D” and “DGTL DTS” settings are canceled and the digital input

mode is automatically reset to “DGTL AUTO.”

INPUT

2. Press INPUT ANALOG/DIGITAL _{ANALOG/DIGITAL}

To change the input mode back to analog input, select

“ANALOG” in step 2.

(INPUT ATT) briefly to change

the input mode.

INPUT ATT

• Each time you press the button, the input

mode changes as follows.

Fr om t he r em ot e cont r ol:

DVD

TV/DBS

VCR 1

DVD MUILTI

VIDEO

CDR

FM/AM

PHONO

USB

1. Press the source selecting

button (DVD, CD, TV/DBS,

CDR, or TAPE/MD)* for

which you want to change

the input mode.

DGTL AUTO

ANALOG

(Digital)

VCR 2

TAPE/MD

DGTL AUTO: Select this for the digital input mode. The

receiver automatically detects the incoming

signal.

ANALOG:

Select this for the analog input mode.

always lights up.

Note:

ANALOG

* Among the source listed above, you can select the digital input

only for the sources which you have selected the digital input

terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting”

on page 19.)

When selecting “DGTL AUTO,” following indicators showing

detected signals light up on the display.

: Always lights up.

: • Lights up when Linear PCM signals come in.

ANALOG/DIGITAL

2. Press ANALOG/DIGITAL INPUT

INPUT

LINEAR PCM

to change the input mode.

• Each time you press the button, the

input mode changes as follows:

• The frame flashes when detecting signals.

• LINEAR PCM without frame flashes when

PCM signals are not recognized.

DIGITAL : Lights up when Dolby Digital signals come in.

DGTL AUTO

ANALOG

(Digital)

: Lights up when DTS Digital Surround signals

come in.

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, “DGTL AUTO” may not happen to

work well. In this case press CONTROL UP 5/DOWN ∞ on

the front panel to select “DGTL D.D” or “DGTL DTS” (while

“DGTL AUTO” remains on the display).

Note:

You can select “DGTL D.D” or “DGTL DTS” from the remote control by

using the On-Screen Menus (see page 36).

Download from Www.Somanuals.com. All Manuals Search And Download.

S howing t he Text Infor m a t ion on t he

Dis pla y

Ba s ic S et t ing a nd Adjus t m ent — Aut o

M em or y

Without any setting required, this receiver stores different sound

settings for each different playing source automatically whenever

you do the following:

• Turning on the power (see page 11)

• Changing the source to play (see page 11)

• Changing the source name (see page 16)

When you have connected an MD recorder or CD player equipped

with TEXT COMPU LINK remote control system (see page 42),

you can show the text information, such as disc title or track title,

on the display of this receiver. To show it on the display, follow the

procedure below.

So, you do not have to change the sound settings next time you

select the same source. The stored settings for the selected source

are automatically recalled.

Before you start, remember....

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

The following settings are automatically stored for each source:

• Front speaker output balance (see page 16)

• Subwoofer setting and its output level (see page 17)

• Input attenuator mode (see page 14)

On t he fr ont pa nel ONLY:

1. Press SETTING repeatedly until “FL

CT SETTING

DISP” (Display) appears on the

display.

• Midnight mode (see page 13)

The display changes to show the current setting.

• Bass boost (see page 14)

• Digital equalization adjustment (see page 15)

• Line direct (see page 14)

• Surround mode on/off (see page 26)

• Surround/DSP mode setting (see pages 27 – 34)

• DVD MULTI playback mode setting (see page 35)

• Analog/digital input mode (see page 20)

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to select either the source name or

the text information to be shown

on the display.

• Each time you press the button, the display

changes to show the following:

You can assign and store the volume level for each source. See

below.

NORM

(Normal)

TEXT

Notes:

NORM:

TEXT:

Source name and Surround/DSP mode appear

during play.

• If the source is FM or AM, you can assign different settings for each

band.

• You cannot assign and store different settings for each digital input

mode.

Text information appears during play.

• The Surround modes and DSP modes cannot be used with DVD

MULTI playback mode at the same time.

Note:

Though you have selected “TEXT,” the source name and Surround /

DSP mode appear if a playing disc has no text information.

To s t or e t he volum e level

Before you start, remember....

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On t he fr ont pa nel ONLY:

1. Press SETTING repeatedly until “ONE

ECT SETTING

TOUCH” appears on the display.

The display changes to show the current setting.

CONTROL

2. Press CONTROL UP 5/DOWN ∞

DOWN

to turn on the One Touch

Operation.

The ONE TOUCH OPERATION indicator

lights up on the display.

• Each time you press the button, the one touch operation

function turns on (“ON”) and off (“OFF”).

To recall the volume level

With the ONE TOUCH OPERATION indicator lit, the volume level

for the currently selected source is recalled when the source is

selected.

To cancel the One Touch Operation

Select “OFF” in step 2 above so that the ONE TOUCH

OPERATION indicator goes off. (Even though the One Touch

Operation is canceled, the recalled volume remains active.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Receiving Ra dio Br oa dca s t s

You can browse through all the stations or use the preset function to go immediately to a particular station.

Tuning in S t a t ions M a nua lly

Us ing P r es et Tuning

On t he fr ont pa nel:

Once a station is assigned to a channel number, the station can be

quickly tuned. You can preset up to 30 FM and 15 AM stations.

FM/AM

1. Press FM/AM to select the band

(FM or AM).

To s t or e t he pr es et s t a t ions

The FM/AM lamp on the front panel button lights

up. The last received station of the selected band is

tuned in.

• Each time you press the button, the band

alternates between FM and AM.

Before you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On t he fr ont pa nel ONLY:

TUNED STEREO

ANALOG

1. Tune in the station you want to preset (see

SPEAKERS

“Tuning in Stations Manually” on the left).

• If you want to store the FM reception mode for this station,

select the FM reception mode you want. See “Selecting the

FM Reception Mode” on page 23.

VOLUME

FM/AM TUNING

2. Press FM/AM TUNING 5/∞ until

you find the frequency you want.

• Pressing FM/AM TUNING 5 increases

the frequency.

TUNED STEREO

ANALOG

SPEAKERS

VOLUME

• Pressing FM/AM TUNING ∞ decreases

the frequency.

Fr om t he r em ot e cont r ol:

MEMORY

2. Press MEMORY.

FM / AM

1. Press FM/AM to select the band

TUNED STEREO

ANALOG

(FM or AM).

The FM/AM lamp on the front panel button

lights up. The last received station of the

selected band is tuned in.

• Each time you press the button, the band

alternates between FM and AM.

SPEAKERS

VOLUME

The channel number position starts flashing on the display for

about 10 seconds.

FM/AM PRESET

3. Press FM/AM PRESET 5/∞ to

select a channel number while the

channel number position is

flashing.

2. Press TUNING UP 3 or

TUNING DOWN 2 until you

SET

DOWN – TUNING – UP

find the frequency you want.

• Pressing TUNING UP 3 increases the

frequency.

MEMORY

4. Press MEMORY again while the

selected channel number is

flashing on the display.

• Pressing TUNING DOWN 2 decreases the

frequency.

The selected channel number stops flashing.

The station is assigned to the selected channel number.

Notes:

• When a station of sufficient signal strength is tuned in, the TUNED

indicator lights up on the display.

TUNED STEREO

ANALOG

• When an FM stereo program is received, the STEREO indicator

also lights up.

SPEAKERS

VOLUME

• When you hold the button (and release it) in step 2, the frequency

keeps changing until a station is tuned in.

5. Repeat steps 1 to 4 until you store all the stations

you want.

To erase a stored preset station

Storing a new station on a used number erases the previously stored

one.

Download from Www.Somanuals.com. All Manuals Search And Download.

To t une in a pr es et s t a t ion

On t he fr ont pa nel:

S elect ing t he FM Recept ion M ode

W hen a n FM s t er eo br oa dca s t is ha r d t o

r eceive or nois y

FM/AM

1. Press FM/AM to select the band

(FM or AM).

You can change the FM reception mode while receiving an FM

broadcast.

• You can store the FM reception mode for each preset station.

The FM/AM lamp on the front panel button lights

up. The last received station of the selected band is

tuned in.

• Each time you press the button, the band

alternates between FM and AM.

Press FM MODE.

• Each time you press the button, the FM reception mode alternates

between “AUTOMUTING” and “MONO.”

FM/AM PRESET

2. Press FM/AM PRESET 5/∞ until

you find the channel you want.

• Pressing FM/AM PRESET 5 increases the

number.

FM MODE

REAR L

∗

FM MODE

• Pressing FM/AM PRESET ∞ decreases the

number.

On the front panel

From the remote control

Fr om t he r em ot e cont r ol:

FM / AM

1. Press FM/AM.

AUTO MUTING TUNED STEREO

ANALOG

The last received station of the selected band is

tuned in.

SPEAKERS

VOLUME

• Each time you press the button, the band

alternates between FM and AM.

BASS

BOOST

ROOM

SIZE

EFFECT

2. Press the 10 keys to select a preset

channel number.

CTRTONE

TUNED

TEST

LIVENESS

ANALOG

• For channel number 5, press 5.

• For channel number 15, press +10 then 5.

• For channel number 20, press +10 then 10.

• For channel number 30, press +10, +10,

then 10.

ENTER

SUBWFR

L/R BAL

CENTER

SPEAKERS

∗

VOLUME

7/P

DIGITALEQ

REAR L

REAR R

∗

RETURN

+10

100

FM MODE

AUTOMUTING: When a program is broadcasted in stereo, you

will hear stereo sound; when in monaural, you will

hear monaural sounds. This mode is also useful to

suppress static noise between stations. The AUTO

MUTING indicator lights up on the display.

Note:

When you use the 10 keys on the remote control, be sure that they

are activated for the tuner, not for the CD and others. (See page 11.)

MONO: Reception will be improved although you will lose the

stereo effect. In this mode, you will hear noise while

tuning into the stations. The AUTO MUTING indicator

goes off from the display.

Note:

When using the FM MODE on the remote control, be sure that the 10

keys are activated for the tuner, not for the CD and others. (See page

11.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Cr ea t ing a S ur r ound Field in Your Room

The built-in Surround Processor provides Surround mode and four types of the DSP (Digital Signal Processor) mode —

DAP (Digital Acoustic Processor) mode, 5 CH/ 4 CH Stereo mode, 3 D-PHONIC mode, and HEADPHONE DSP mode.

W ith this receiver, you can use a Surround mode and a DSP mode at the same time. Once you have adjusted Surround

and/ or DSP modes, the adjustments done for each source are memorized.

S ur r ound m odes

DS P m odes

With this receiver, you can use two types of the Surround mode.

Following modes cannot be used when only the front speakers

are connected to this receiver (without the rear speakers or

center speaker).

With this receiver, you can use four types of the DSP mode.

DAP m odes

In order to reproduce a more acoustic sound field in your listening

room while playing music sources, you can use DAP modes. This

mode can be used when the front speakers are connected to this

receiver (without respect to the rear/center speaker connection).

Dolby S ur r ound (Dolby Digit a l a nd Dolby P r o Logic) *

Used to watch the soundtracks of software encoded with Dolby

Digital (bearing the mark

) or with Dolby Surround

DOLBY SURROUND

(bearing the mark

Dolby Surround encoding format records the left front channel, right

front channel, center channel, and rear channel (total 4 channels)

signals into 2 channels. The Dolby Pro Logic decoder built in this

receiver decode these 2 channel signals into original 4 channel

signals — matrix-based multichannel reproduction, and allows you

to enjoy the realistic sound field in your listening room.

On the other hand, Dolby Digital encoding method (so called a

discrete 5.1 channel digital audio format) records and compresses

the left front channel, right front channel, center channel, left rear

channel, right rear channel, and LFE channel (total 6 channels, but

LFE channel is counted as 0.1 channel, therefore called 5.1

channels) signals digitally. Each channel is completely independent

from other channel signals to avoid interference, therefore, you can

obtain much better sound quality with much stereo and surround

effects.

THEATER 1: Reproduces the sound field of a large theater

(where the seating capacity about 1,000).

THEATER 2: Reproduces the sound field of a small theater

(where the seating capacity about 300).

HALL 1:

Gives clear vocal and the feeling of a large concert

hall (where the seating capacity about 1,000).

HALL 2:

Gives clear vocal and the feeling of a small concert

hall (where the seating capacity about 300).

LIVE CLUB: Gives the feeling of a live music club with a low

ceiling.

DANCE CLUB: Gives a throbbing bass beat.

PAVILION:

Gives the spacious feeling of a pavilion with a

high ceiling.

The Dolby Digital decoder built in this receiver can create much

more realistic sound field in your listening room. You may feel as if

you were in a real theater.

In addition, Dolby Digital enables stereo rear sounds, and sets the

cutoff frequency of the rear treble at 20 kHz, comparing to 7 kHz for

Dolby Pro Logic. These facts enhance the sound movement and

being-there feelings much more than Dolby Pro Logic.

• To enjoy the software encoded with Dolby Digital, you must

connect the source component using the digital terminal on the

rear of this receiver. (See page 8.)

5 CH/ 4 CH S t er eo m ode

You can create more powerful sound field for both of the digital and

analog stereo sounds source. The 4 CH Stereo mode reproduces a

sound filed through the front left and right speakers and rear left and

right speakers. The 5 CH Stereo mode adds the center channel

element to the 4 CH Stereo sound field by outputting mixed left and

right signals through the center speaker. This mode cannot be used

when only the front speakers are connected to this receiver

without the rear speakers.

DTS Digit a l S ur r ound **

DTS Digital Surround is another discrete 5.1 channel digital audio

format available on CD, LD, and DVD software encoded with DTS

Note:

Digital Surround (bearing the mark

“5CH STEREO” is selected when setting the center speaker to

“LARGE” or “SMALL,” and “4CH STEREO” is selected when setting

the center speaker to “NONE” (see page 17).

Comparing to Dolby Digital, audio compression rate is relatively

low. This fact allows DTS Digital Surround format to add breadth

and depth to the reproduced sounds. As a result, DTS Digital

Surround features natural, solid and clear sound.

• To enjoy the software encoded with DTS Digital Surround, you

must connect the source component using the digital terminal on

the rear of this receiver. (See page 8.)

* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro

Logic,” and the double-D symbol are trademarks of Dolby

** Manufactured under license from Digital Theater Systems, Inc. US

Pat. No. 5,451,942 and other world-wide patents issues and

pending. “DTS” and “DTS Digital Surround” are trademarks of

Download from Www.Somanuals.com. All Manuals Search And Download.

3 D-P HONIC m odes

Repr oducing t he S ound Field

The 3D-PHONIC mode gives you such a nearly surround effect as is

reproduced through the Dolby Surround decoder, which is widely

used to reproduce sounds with a feeling of movement like those

experienced in movie theaters. The 3D-PHONIC mode is the result

of research on sound localization technology carried out at JVC for

many years. This mode can be used when the front speakers are

connected to this receiver (without respect to the rear/center

speaker connection). When the 3D PHONIC mode is reproduced

with the center speaker connected, you can feel as if actors on the

screen actually speak in your room.

The sound heard in a concert hall or club consists of direct sound

and indirect sound — early reflections and reflections from behind.

Direct sounds reach the listener directly without any reflection. On

the other hand, indirect sounds are delayed by the distances of the

ceiling and walls. These direct sounds and indirect sounds are the

most important elements of the acoustic surround effects.

The Surround and DSP modes can create these important elements,

and give you a real “being there” feeling.

• You can select “3D ACTION” only when playing an analog or

linear PCM (digital) source.

• You can select “3D DIGITAL” only when playing a source

encoded with Dolby Digital or DTS Digital Surround.

Reflections from

behind

Early reflections

3D ACTION: Best for action and war movies — where the

action is fast and explosive.

3D DIGITAL: Reproduces multichannel source encoded with

Dolby Digital or with DTS Digital Surround.

HEADP HONE DS P m ode

The HEADPHONE DSP mode can create the stereo sound as if you

listen through the speakers while listening to a source using

headphones. So you can feel as if you were in a music room. This

mode can be used only when both of the front speakers are

deactivated (see page 13.)

Direct sounds

DVD M ULTI P la yba ck M ode

This receiver provides the DVD MULTI playback mode for

reproducing the analog discrete 5.1 channel output mode of the

DVD player or other equipment.

You can adjust the DVD MULTI playback mode while playing

back a video software such as a DVD using the analog discrete

5.1 channel output mode.

• For the DVD MULTI playback mode connection, see page 7.

• For details on the DVD MULTI playback mode, see page 35.

Notes:

• When you select “DVD MULTI” as the source to play, you cannot

select or adjust the Surround and DSP modes.

• The PRO LOGIC indicator lights up when the Dolby Pro Logic

decorder built in this receiver is activated.

• When the line direct function is turned on, the Surround and DSP

modes are canceled temporarily (see page 14).

• No adjustment can be made for the HEADPHONE DSP mode.

DSP Modes Available to Input Mode

⅜: Possible /

: Impossible

MODE

SURROUND

HEADPHOHE

SURR.

OFF

DSP OFF

SURROUND

DAP MODE

5 CH/4 CH

Stereo

with

HEADPHONE HEADPHONE

DSP

INPUT

SIGNAL

ACTION

(DIGITAL)

DAP

ANALOG

(2 CH)

⅜

(DOLBY PRO LOGIC)

(3D ACTION)

DVD MULTI

(5.1 CH)

⅜

LINEAR PCM

DOLBY DIGITAL

DTS

⅜

(3D ACTION)

(DOLBY PRO LOGIC)

⅜

(DOLBY DIGITAL)

(3D DIGITAL)

⅜

(3D DIGITAL)

(DTS SURROUND)

When 2 channel signal comes in, DOLBY PRO LOGIC is selected. When other signals come in, DOLBY DIGITAL is selected.

When 2 channel signal comes in, DOLBY PRO LOGIC is selected. When other signals come in, DTS SURROUND is selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ava ila ble DS P M odes Accor ding t o t he S pea ker Ar r a ngem ent

Available DSP modes will vary depending on how many speakers are used with this receiver.

Make sure that you have set the speaker information correctly (see page 17).

Speaker arrangements

Available DSP modes

Each time you press DSP MODE, the DSP modes change as follows:

THEATER 1 \ THEATER 2

\ HALL 1

\ HALL 2 \

Front

speaker

Front

speaker

LIVE CLUB \ DANCE CLUB \ PAVILION

5CH STEREO (when using 5 speakers) or 4CH STEREO (when using 4 speakers)*

3D ACTION or 3D DIGITAL

(Back to the beginning)

Center speaker

\ SURR. OFF (DSP OFF)

To activate the Surround mode, press SURROUND ON/OFF button so that the

SURROUND ON/OFF lamp on the front panel button lights up.

Rear

speaker

Rear

speaker

Notes:

• If the settings for the center and the rear speakers are changed to “NONE” (see page 17),

the Surround mode will be canceled.

Front

speaker

Front

speaker

• When both of the Surround mode and DSP mode are deactivated, “SURR. OFF” appears

on the display.

* “5CH STEREO” is selected when setting the center speaker to “LARGE” or “SMALL,” and

“4CH STEREO” is selected when setting the center speaker to “NONE” (see page 17).

Rear

speaker

Rear

speaker

THEATER 1 \ THEATER 2

\ HALL 1

\ HALL 2 \

LIVE CLUB \ DANCE CLUB \ PAVILION

3D ACTION or 3D DIGITAL

Front

speaker

Front

speaker

\ SURR. OFF (DSP OFF)

(Back to the beginning)

Center speaker

To activate the Surround mode, press SURROUND ON/OFF button so that the

SURROUND ON/OFF lamp on the front panel button lights up.

Notes:

• If the setting for the center speaker is changed to “NONE” (see page 17), the Surround

mode will be canceled.

• When both of the Surround mode and DSP mode are deactivated, “SURR. OFF” appears

on the display.

THEATER 1 \ THEATER 2

\ HALL 1

\ HALL 2 \

Front

speaker

Front

speaker

LIVE CLUB \ DANCE CLUB \ PAVILION

3D ACTION or 3D DIGITAL

\ SURR. OFF (DSP OFF)

(Back to the beginning)

Note:

Surround mode cannot be used when only the front speakers are connected.

HEADPHONE

HEADPHONE DSP

Note:

To use the HEADPHONE or HEADPHONE DSP mode, deactivate both of the front speakers

(see page 13).

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Select the speaker you want to adjust.

• To select the center speaker level, press CENTER.

“CTR” appears on the remote control display window.

• To select the left rear speaker level, press REAR L.

“REARL” appears on the remote control display window.

• To select the right rear speaker level, press REAR R.

“REARR” appears on the remote control display window.

Adjus t ing t he S ur r ound M odes

You can also use a Surround mode with a DAP mode (see page 30).

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NONE.” See page 17.

• You cannot adjust the center speaker output level and center tone

when you have set “CTR SPK” to “NONE.” See page 17.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

REAR R

REAR L

CENTER

∗

+10

100

FM MODE

BAL L

∗

6. Press LEVEL +/– to adjust the

CH/ LEVEL

speaker output levels (–10 dB to

+10 dB).

∗

−

BAL R

∗

Fr om t he r em ot e cont r ol:

7. Press SOUND.

SOUND

1. Select and play a sound source.

• To adjust other speaker output levels, repeat

• To enjoy Dolby Pro Logic, play back a software encoded with

steps 5 and 6.

DOLBY SURROUND

Dolby Surround and labeled with

mark.

TEST

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

• To enjoy DTS Digital Surround, play back a software encoded

8. Press TEST again to stop the test

tone.

with DTS Digital Surround and labeled with

mark.

9. Press CTR TONE to select the

CTRTONE

SURROUND

ON/OFF

center tone level you want.

The center tone adjustment affects the mid-

frequency range, which the human voice is

mostly made up of.

• Each time you press the button, the display changes to show

the following:

2. Press SURROUND ON/OFF to

activate an appropriate Surround

mode — PRO LOGIC, DOLBY

DIGITAL or DTS SURROUND.

ENTER

The SURROUND ON/OFF lamp on the front panel button lights

up.

• Each time you press the button, the Surround mode turns on

and off alternately.

• When “PRO LOGIC” is selected, the PRO LOGIC indicator

lights up on the display.

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

SOUND

3. Press SOUND.

The 10 keys are activated for sound adjustments.

When “CTR TONE 3” is selected, no adjustment is applied.

4. Press TEST to check the speaker

TEST

output balance.

On t he fr ont pa nel:

“TEST TONE L” starts flashing on the

display, and a test tone comes out of the

speakers in the following order:

You can also use the buttons on the front panel to adjust the

Surround modes. However, no test tone is available when using the

buttons on the front panel. So, make adjustments while listening to

the sound of the source played back.

TEST TONE L

TEST TONE R

TEST TONE C

(Left front speaker)

(Right front speaker)

(Center speaker)

1. Select and play a sound source.

TEST TONE LS

TEST TONE RS

• To enjoy Dolby Pro Logic, play back a software encoded with

(Left rear speaker)

(Right rear speaker)

DOLBY SURROUND

Dolby Surround and labeled with

mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

Notes:

• To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

• You can adjust the speaker output levels without outputting the

test tone.

• No test tone comes out of the center speaker when “CTR SPK”

is set to “NONE” (see page 17).

• No test tone comes out of the rear speakers when “REAR SPK”

is set to “NONE” (see page 17).

• If the TV is turned on and the proper video input is selected on

the TV, the test tone screen will appear on the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

SURROUND ON/OFF

On t he fr ont pa nel:

2. Press SURROUND ON/OFF to

activate an appropriate Surround

mode — PRO LOGIC, DOLBY

DIGITAL or DTS SURROUND.

DSP MODE

1. Press DSP MODE repeatedly until

the DAP mode you want to adjust

— THEATER 1, THEATER 2,

HALL 1, HALL 2, LIVE CLUB,

DANCE CLUB, or PAVILION —

appears on the display.

The SURROUND ON/OFF lamp on the front panel button lights

up.

• Each time you press the button, the Surround mode turns on

and off alternately.

• When “PRO LOGIC” is selected, the PRO LOGIC indicator

lights up on the display.

The DSP MODE lamp on the front panel button lights up, and

the DSP indicator also lights up on the display.

• When you have set “REAR SPK” to “NONE,” the 3D-

PHONIC indicator also lights up.

3. Adjust the speaker output levels.

1) Press LEVEL ADJUST repeatedly

TAL LEVEL

2. Adjust the speaker output levels.

ADJUST

until one of the following indications

appears on the display.

“CENTER”:

To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level.

“REAR R”:

1) Press LEVEL ADJUST repeatedly

TAL LEVEL

ADJUST

until one of the following indications

appears on the display.

“CENTER”:

To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level.

“REAR R”:

To adjust the right rear speaker level.

2) Press CONTROL UP 5/DOWN ∞ to

adjust the selected speaker output level

(from –10 dB to +10 dB).

CONTROL

To adjust the right rear speaker level.

2) Press CONTROL UP 5/DOWN ∞ to

adjust the selected speaker output level

(from –10 dB to +10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output levels.

DOWN

CONTROL

DOWN

3) Repeat 1) and 2) to adjust the other

speaker output levels.

4. Adjust the center tone.

EFFECT SETT

CONTROL

1) Press EFFECT repeatedly until “CTR

3. Adjust the center tone.

EFFECT SETT

CONTROL

TONE” appears on the display.

1) Press EFFECT repeatedly until “CTR

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the center tone level you want.

• Each time you press the button, the

display changes to show the following:

TONE” appears on the display.

DOWN

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the center tone level you want.

The center tone adjustment affects the

mid-frequency range, which the human

voice is mostly made up of.

DOWN

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

• Each time you press the button, the

display changes to show the following:

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

Adjus t ing t he DAP M odes

You can also use a DAP mode with a Surround mode (see page 30).

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 2 again.

• You cannot adjust the rear speaker output level when you have set

“REAR SPK” to “NONE.” See page 17.

• You cannot adjust the center speaker output level when you have

set “CTR SPK” to “NONE.” See page 17.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

Continued to the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Adjust the overall levels of the effect.

1) Press EFFECT repeatedly until

“EFFECT” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞

to select the effect level you want.

3. Select the speaker you want to adjust.

• To select the center speaker level, press CENTER.

“CTR” appears on the remote control display window.

• To select the left rear speaker level, press REAR L.

“REARL” appears on the remote control display window.

• To select the right rear speaker level, press REAR R.

“REARR” appears on the remote control display window.

EFFECT SETT

CONTROL

DOWN

• Each time you press the button, the

display changes to show the following:

REAR L

CENTER

∗

REAR R

∗

+10

EFFECT 1

EFFECT 2

EFFECT 3

FM MODE

100

EFFECT 4

EFFECT 5

BAL L

4. Press LEVEL +/– to adjust the

speaker output levels (–10 dB to

+10 dB).

∗

As the number increases, the selected DAP effect becomes

stronger. (Normally set it to “EFFECT 3.”)

CH/ LEVEL

∗

−

5. Adjust the room size (sense of spaciousness).

BAL R

∗

5. Press SOUND.

1) Press EFFECT repeatedly until

SOUND

EFFECT SETTIN

• To adjust other speaker output levels, repeat

steps 3 and 4.

“ROOM SIZE” appears on the

display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the room size you want.

• Each time you press the button, the

display changes to show the following:

CTRTONE

6. Press CTR TONE to select the

CONTROL

DOWN UP

center tone level you want.

• Each time you press the button, the display

changes to show the following:

ENTER

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

ROOMSIZE 1

ROOMSIZE 2

ROOMSIZE 3

CTR TONE 5

CTR TONE 4

ROOMSIZE 5

ROOMSIZE 4

(Sharper)

(Sharp)

As the number increases, the interval between reflections

increases so that you will feel as if you were in a larger

room. (Normally set it to “ROOMSIZE 3.”)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

6. Adjust the liveness.

When “CTR TONE 3” is selected, no adjustment is applied.

EFFECT SETT

1) Press EFFECT repeatedly until

“LIVENESS” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the liveness level you want.

EFFECT

7. Press EFFECT to adjust the

overall level of the effect.

• Each time you press the button, the effect

CONTROL

DOWN UP

level changes as follows:

• Each time you press the button, the

display changes to show the following:

EFFECT 1

EFFECT 2

EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected DAP effect becomes

stronger. (Normally set it to “EFFECT 3.”)

LIVENESS 1

LIVENESS 2

LIVENESS 3

LIVENESS 5

LIVENESS 4

ROOM

8. Press ROOM SIZE to adjust the

SIZE

As the number increases, the attenuation level of reflections

over time decreases so that acoustics change from “Dead” to

“Live.” (Normally set it to “LIVENESS 3.”)

room size (sense of spaciousness).

• Each time you press the button, the display

changes to show the following:

Fr om t he r em ot e cont r ol:

DSP

1. Press DSP MODE repeatedly until the

MODE

ROOMSIZE 1

ROOMSIZE 2

ROOMSIZE 3

ROOMSIZE 5

ROOMSIZE 4

DAP mode you want to adjust —

THEATER 1, THEATER 2, HALL 1,

HALL 2, LIVE CLUB, DANCE CLUB, or

As the number increases, the interval between reflections

increases so that you will feel as if you were in a larger room.

(Normally set it to “ROOMSIZE 3.”)

PAVILION — appears on the display.

The DSP MODE lamp on the front panel button lights up, and

the DSP indicator also lights up on the display.

• When you have set “REAR SPK” to “NONE,” the 3D-

PHONIC indicator also lights up.

SOUND

2. Press SOUND.

The 10 keys are activated for sound adjustments.

Download from Www.Somanuals.com. All Manuals Search And Download.

TEST

LIVENESS

9. Press LIVENESS to adjust the liveness.

• Each time you press the button, the

5. Press TEST to check the speaker

output balance.

display changes to show the following:

“TEST TONE L” starts flashing on the

display, and a test tone comes out of the

speakers in the following order:

LIVENESS 1

LIVENESS 2

LIVENESS 3

LIVENESS 5

LIVENESS 4

TEST TONE L

TEST TONE R

TEST TONE C

(Left front speaker)

(Right front speaker)

(Center speaker)

As the number increases, the attenuation level of reflections

over time decreases so that acoustics change from “Dead” to

“Live.” (Normally set it to “LIVENESS 3.”)

TEST TONE LS

TEST TONE RS

(Left rear speaker)

(Right rear speaker)

Notes:

Adjus t ing t he S ur r ound M odes wit h t he

DAP M odes

• You can adjust the speaker output levels without outputting the

test tone.

• No test tone comes out of the center speaker when “CTR SPK”

is set to “NONE” (see page 17).

• No test tone comes out of the rear speakers when “REAR SPK”

is set to “NONE” (see page 17).

• If the TV is turned on and the proper video input is selected on

the TV, the test tone screen will appear on the TV.

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 4 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NONE.” See page 17.

• You cannot adjust the center speaker output level and center tone

when you have set “CTR SPK” to “NONE.” See page 17.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

6. Select the speaker you want to adjust.

• To select the center speaker level, press CENTER.

“CTR” appears on the remote control display window.

• To select the left rear speaker level, press REAR L.

“REARL” appears on the remote control display window.

• To select the right rear speaker level, press REAR R.

“REARR” appears on the remote control display window.

Fr om t he r em ot e cont r ol:

REAR L

CENTER

REAR R

∗

1. Select and play a sound source.

+10

100

FM MODE

• To enjoy Dolby Pro Logic, play back a software encoded with

DOLBY SURROUND

Dolby Surround and labeled with

mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

• To enjoy DTS Digital Surround, play back a software encoded

BAL L

∗

7. Press LEVEL +/– to adjust the

speaker output levels (–10 dB to

+10 dB).

CH/ LEVEL

∗

with DTS Digital Surround and labeled with

mark.

−

BAL R

∗

SURROUND

ON/OFF

2. Press SURROUND ON/OFF to

activate an appropriate Surround

mode — PRO LOGIC, DOLBY

DIGITAL or DTS SURROUND.

8. Press SOUND.

SOUND

• To adjust other speaker output levels repeat steps

6 and 7.

TEST

The SURROUND ON/OFF lamp on the front panel button lights

up.

• Each time you press the button, the Surround mode turns on

and off alternately.

• When “PRO LOGIC” is selected, the PRO LOGIC indicator

lights up on the display.

9. Press TEST again to stop the test

tone.

CTRTONE

10.Press CTR TONE to select the

center tone level you want.

The center tone adjustment affects the mid-

frequency range, which the human voice is

mostly made up of.

ENTER

DSP

3. Press DSP MODE repeatedly until

MODE

the DAP mode you want to adjust

• Each time you press the button, the display changes to show

the following:

— THEATER 1, THEATER 2,

HALL 1, HALL 2, LIVE CLUB,

DANCE CLUB, or PAVILION —

appears on the display.

The DSP MODE lamp on the front panel button lights up, and

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

the DSP indicator also lights up on the display.

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

SOUND

4. Press SOUND.

The 10 keys are activated for sound adjustments.

When “CTR TONE 3” is selected, no adjustment is applied.

Continued to the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

11.Press EFFECT to adjust the

3. Press DSP MODE repeatedly until

the DAP mode you want to adjust

— THEATER 1, THEATER 2,

HALL 1, HALL 2, LIVE CLUB,

DANCE CLUB, or PAVILION —

appears on the display.

DSP MODE

EFFECT

overall level of the effect.

• Each time you press the button, the effect

level changes as follows:

EFFECT 1

EFFECT 2

EFFECT 3

EFFECT 5

EFFECT 4

The DSP MODE lamp on the front panel button lights up, and

the DSP indicator also lights up on the display.

As the number increases, DAP effect becomes stronger.

(Normally set it to “EFFECT 3.”)

4. Adjust the speaker output levels.

1) Press LEVEL ADJUST repeatedly

AL LEVEL

ROOM

SIZE

12.Press ROOM SIZE to adjust the

ADJUST

until one of the following indications

appears on the display.

“CENTER”:

To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level.

“REAR R”:

room size (sense of spaciousness).

• Each time you press the button, the display

changes to show the following:

ROOMSIZE 1

ROOMSIZE 5

As the number increases, the interval between reflections

ROOMSIZE 2

ROOMSIZE 3

ROOMSIZE 4

To adjust the right rear speaker level.

increases so that you will feel as if you were in a larger room.

(Normally set it to “ROOMSIZE 3.”)

CONTROL

2) Press CONTROL UP 5/DOWN ∞ to

DOWN

adjust the selected speaker output level

(from –10 dB to +10 dB).

13.Press LIVENESS to adjust the

LIVENESS

3) Repeat 1) and 2) to adjust the other

speaker output levels.

liveness.

• Each time you press the button, the display

changes to show the following:

5. Adjust the center tone.

1) Press EFFECT repeatedly until “CTR

TONE” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞

to select the center tone level you

want.

EFFECT SETTIN

CONTROL

LIVENESS 1

LIVENESS 2

LIVENESS 3

LIVENESS 5

LIVENESS 4

DOWN

As the number increases, the attenuation level of reflections over

time decreases so that acoustics change from “Dead” to “Live.”

(Normally set it to “LIVENESS 3.”)

• Each time you press the button, the

display changes to show the following:

On t he fr ont pa nel:

CTR TONE 2

CTR TONE 3

CTR TONE 1

You can also use the buttons on the front panel to adjust the sound

with a Surround mode and a DAP mode. However, no test tone is

available when using the buttons on the front panel. So, make

adjustments while listening to the sound of the source played back.

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

DOLBY SURROUND

Dolby Surround and labeled with

mark.

When “CTR TONE 3” is selected, no adjustment is applied.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

6. Adjust the overall levels of the effect.

• To enjoy DTS Digital Surround, play back a software encoded

1) Press EFFECT repeatedly until

EFFECT SETT

with DTS Digital Surround and labeled with

mark.

“EFFECT” appears on the display.

The display shows the current setting.

2. Press SURROUND ON/OFF to

SURROUND ON/OFF

2) Press CONTROL UP 5/DOWN ∞

CONTROL

activate an appropriate Surround

mode — PRO LOGIC, DOLBY

DIGITAL or DTS SURROUND.

The SURROUND ON/OFF lamp on the front panel button lights

up.

to select the effect level you want.

• Each time you press the button, the

display changes to show the following:

DOWN

EFFECT 1

EFFECT 2

EFFECT 3

• Each time you press the button, the Surround mode turns on

and off alternately.

• When “PRO LOGIC” is selected, the PRO LOGIC indicator

lights up on the display.

EFFECT 4

EFFECT 5

As the number increases, DAP effect becomes stronger.

(Normally set it to “EFFECT 3.”)

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Adjust the room size (sense of spaciousness).

2. Adjust the speaker output levels.

1) Press LEVEL ADJUST repeatedly

until one of the following indications

appears on the display.

1) Press EFFECT repeatedly until

TAL LEVEL

EFFECT SETTIN

ADJUST

“ROOM SIZE” appears on the

display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the room size you want.

• Each time you press the button, the

display changes to show the following:

“CENTER” — for 5 CH Stereo mode only:

To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level.

“REAR R”:

CONTROL

DOWN UP

To adjust the right rear speaker level.

2) Press CONTROL UP 5/DOWN ∞ to

adjust the selected speaker output level

(from –10 dB to +10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output levels.

CONTROL

DOWN

ROOMSIZE 1

ROOMSIZE 2

ROOMSIZE 3

ROOMSIZE 5

ROOMSIZE 4

As the number increases, the interval between reflections

increases so that you will feel as if you were in a larger

room. (Normally set it to “ROOMSIZE 3.”)

3. Adjust the center tone — for 5 CH Stereo mode

only.

EFFECT SETT

8. Adjust the liveness.

EFFECT SETT

1) Press EFFECT repeatedly until “CTR

1) Press EFFECT repeatedly until

“LIVENESS” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

select the liveness level you want.

TONE” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞ to

CONTROL

DOWN UP

DOWN

select the center tone level you want.

The center tone adjustment affects the

mid-frequency range, which the

• Each time you press the button, the

display changes to show the following:

human voice is mostly made up of.

• Each time you press the button, the

display changes to show the following:

LIVENESS 1

LIVENESS 2

LIVENESS 3

LIVENESS 5

LIVENESS 4

CTR TONE 2

CTR TONE 3

CTR TONE 1

As the number increases, the attenuation level of reflections

over time decreases so that acoustics change from “Dead” to

“Live.” (Normally set it to “LIVENESS 3.”)

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

Adjus t ing t he 5 CH/ 4 CH S t er eo M ode

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 2 again.

• You cannot adjust the center speaker output level and select the

center tone level for 4 CH Stereo mode.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

Fr om t he r em ot e cont r ol:

1. Press DSP MODE repeatedly until

DSP

MODE

“5CH STEREO” or “4CH

STEREO” appears on the display.

The DSP MODE lamp on the front panel button lights up, and

the DSP indicator also lights up on the display.

• “4CH STEREO” appears on the display when you have set

“CTR SPK” to “NONE” (see page 17).

On t he fr ont pa nel:

DSP MODE

1. Press DSP MODE repeatedly until

SOUND

“5CH STEREO” or “4CH

2. Press SOUND.

STEREO” appears on the display.

The DSP MODE lamp on the front panel

button lights up, and the DSP indicator also lights up on the

display.

• “4CH STEREO” appears on the display when you have set

“CTR SPK” to “NONE” (see page 17).

The 10 keys are activated for sound adjustments.

3. Select the speaker you want to adjust.

• To select the center speaker level, press CENTER— for 5 CH

Stereo mode only.

“CTR” appears on the remote control display window.

• To select the left rear speaker level, press REAR L.

“REARL” appears on the remote control display window.

• To select the right rear speaker level, press REAR R.

“REARR” appears on the remote control display window.

REAR R

REAR L

CENTER

∗

+10

100

FM MODE

Continued to the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

BAL L

∗

4. Press LEVEL +/– to adjust the

speaker output levels (–10 dB to

+10 dB).

Adjus t ing t he 3 D-P HONIC M odes

CH/ LEVEL

∗

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

−

BAL R

∗

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 2 again.

• You cannot adjust the center speaker output level when you have

set “CTR SPK” to “NONE” See page 17.

5. Press SOUND.

SOUND

• To adjust other speaker output levels, repeat

steps 3 and 4.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

6. Press CTR TONE to select the

center tone level you want — for

CTRTONE

ENTER

5 CH Stereo mode only.

On t he fr ont pa nel:

The center tone adjustment affects the mid-

frequency range, which the human voice is

mostly made up of.

DSP MODE

1. Press DSP MODE repeatedly until

“3D ACTION” or “3D DIGITAL”

• Each time you press the button, the display changes to show

the following:

appears on the display.

The DSP MODE lamp on the front panel

button lights up, and the 3D-PHONIC and DSP indicators also

light up on the display.

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

2. Adjust the center speaker output level.

(Sharper)

LEVEL

ADJUST

(Sharp)

1) Press LEVEL ADJUST repeatedly

until “CENTER” appears on the

display.

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

2) Press CONTROL UP 5/DOWN ∞ to

adjust the center speaker output level

(from –10 dB to +10 dB).

To make the dialogue clearer, select “CTR TONE 3” or “CTR

TONE 4.”

When “CTR TONE 3” is selected, no adjustment is applied.

CONTROL

DOWN UP

3. Adjust the center tone.

1) Press EFFECT repeatedly until “CTR

TONE” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞

to select the center tone level you

want.

EFFECT SETT

CONTROL

DOWN

• Each time you press the button, the

display changes to show the following:

CTR TONE 2

CTR TONE 3

CTR TONE 1

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

Download from Www.Somanuals.com. All Manuals Search And Download.

CTRTONE

4. Adjust the overall levels of the effect.

1) Press EFFECT repeatedly until

“EFFECT” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN ∞

to select the effect level you want.

6. Press CTR TONE to select the

EFFECT SETT

CONTROL

center tone level you want.

• Each time you press the button, the display

changes to show the following:

ENTER

DOWN

CTR TONE 2

CTR TONE 3

CTR TONE 1

• Each time you press the button, the

display changes to show the following:

(Softer)

(Soft)

(Flat)

CTR TONE 5

CTR TONE 4

(Sharper)

(Sharp)

EFFECT 1

EFFECT 2

EFFECT 3

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

EFFECT 4

EFFECT 5

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

As the number increases, the selected 3D effect mode

becomes stronger. (Normally set it to “EFFECT 3.”)

Fr om t he r em ot e cont r ol:

DSP

1. Press DSP MODE repeatedly until

MODE

7. Press EFFECT to adjust the

EFFECT

overall level of the effect.

• Each time you press the button, the effect

level changes as follows:

“3D ACTION” or “3D DIGITAL”

appears on the display.

The DSP MODE lamp on the front panel button lights up, and

EFFECT 1

EFFECT 2

EFFECT 3

the 3D-PHONIC and DSP indicators also light up on the display.

EFFECT 5

EFFECT 4

SOUND

2. Press SOUND.

The 10 keys are activated for sound

As the number increases, 3D effect mode becomes stronger.

(Normally set it to “EFFECT 3.”)

adjustments.

3. Press CENTER to select the center

CENTER

∗

speaker.

• “CTR” appears on the remote control display

window.

BAL L

∗

4. Press LEVEL +/– to adjust the

center speaker output levels (from

–10 dB to +10 dB).

CH/ LEVEL

∗

−

BAL R

∗

SOUND

5. Press SOUND.

Download from Www.Somanuals.com. All Manuals Search And Download.

Us ing t he DVD M ULTI P la yba ck M ode

This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD

player. Before playing back a DVD, refer also to the manual supplied with the DVD player.

Fr om t he r em ot e cont r ol:

Act iva t ing t he DVD M ULTI P la yba ck M ode

DVD MUILTI

1. Press DVD MULTI so that “DVD

You can adjust the DVD MULTI playback mode while playing back

a DVD using the analog discrete output mode on the DVD player.

Once you have made adjustments, the receiver memorizes the

adjustments until you change them. You also need to set the DVD

player to the analog discrete output mode.

MULTI” appears on the display.

The DVD MULTI lamp on the front panel button

lights up.

Note:

When you select “DVD MULTI” as the source to play, the Surround

and DSP modes are canceled, and the SURROUND ON/OFF and

DSP MODE buttons do not work.

Before you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

2. Select the analog discrete output mode on the

DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

On t he fr ont pa nel:

DVD MULTI

1. Press DVD MULTI so that “DVD

If you need to make any adjustment, go to the following

steps.

MULTI” appears on the display.

The DVD MULTI lamp on the front panel button

lights up.

3. Press SOUND.

SOUND

The 10 keys are activated for adjusting the

Note:

sound.

When you select “DVD MULTI” as the source to play, the Surround

and DSP modes are canceled, and the SURROUND ON/OFF and

DSP MODE buttons do not work.

4. Select the speaker you want to adjust.

• To select the center speaker level, press CENTER.

“CTR” appears on the remote control display window.

• To select the left rear speaker level, press REAR L.

“REARL” appears on the remote control display window.

• To select the right rear speaker level, press REAR R.

“REARR” appears on the remote control display window.

2. Select the analog discrete output mode on the

DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

If you need to make any adjustment, go to the following

steps.

CENTER

REAR R

∗

REAR L

∗

+10

100

FM MODE

3. Adjust the speaker output levels.

1) Press LEVEL ADJUST repeatedly

AL LEVEL

BAL L

ADJUST

∗

5. Press LEVEL +/– to adjust the

speaker output levels (from

–10 dB to +10 dB).

until one of the following indications

appears on the display.

“CENTER”:

To adjust the center speaker level.

“REAR L”:

To adjust the left rear speaker level.

“REAR R”:

CH/ LEVEL

∗

−

BAL R

∗

SOUND

6. Press SOUND.

• To adjust other speaker output levels, then repeat

To adjust the right rear speaker level.

steps 4 and 5.

2) Press CONTROL UP 5/DOWN ∞ to

CONTROL

DOWN

adjust the selected speaker output level

(from –10 dB to +10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output levels.

Notes:

• You cannot adjust the center tone level.

• You cannot use the midnight mode for DVD MULTI playback mode

(see page 13).

• When using a pair of headphones, the sounds of front left and right

are output from the headphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

Us ing t he On-S cr een M enus

You can use the Menus on the TV screen to control the receiver.

To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 7 ), and set the

TV’s input mode to the proper position to which the receiver is connected.

•

W hen the TV’s input mode is incorrect; for example, a different video input or TV tuner mode is selected, you

cannot show the Menus on the TV screen.

Act iva t ing t he S ur r ound M odes

On-Screen Operation buttons (on the remote control)

(Also see page 27)

1. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

When you press MENU, “MENU”

appears on the display window

for about 10 seconds.

2. Press 5 / ∞ to move

CATV/DBS VCR 1

AUDIO

POWER

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

to “SURROUND.”

TV/DBS

VCR 1

VIDEO

VCR 2

TAPE/MD

3. Press 2 / 3 to select the

Surround mode you

want to use.

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

MIDNIGHT

CTRTONE

MODE

SOUND

MUTING

TEST

LIVENESS

ENTER

SUBWFR

L/R BAL

CENTER

∗

7/P

DIGITALEQ

REAR L

REAR R

∗

4. When you finish, press

EXIT.

RETURN

+10

100

PLAY

FM MODE

EXIT

CATV/DBS

CONTROL

BAL L

∗

CH/ LEVEL TV VOL

VOLUME

∗

TV/VIDEO

The menu disappears from the TV.

−

BAL R

∗

/REW

FF/

PAUSE

SET

PLAY

EXIT

TEXT

DISPLAY

/REW

FF/

PAUSE

SET

Act iva t ing t he DS P M odes (Also see page 28)

REC

PAUSE

DOWN – TUNING

–

DOWN – TUNING – UP

1. Press MENU.

CONTROL

STOP

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

RM-SRX8010J

A/V CONTROL RECEIVER

STOP

2. Press 5 / ∞ to move

to “DSP MODE.”

3. Press 2 / 3 to select the

DSP mode you want to

use.

Showing t he MENU on t he TV Scr een

Press MENU.

4. When you finish, press

EXIT.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

The menu disappears from the TV.

Note

If “DVD MULTI” is selected as a playing source, the “SURROUND

MODE” and “DSP MODE” do not appear on the display.

Use 5 / ∞ to move

up and down, and 2 / 3

to select, adjust or set

the item.

Select ing t he Ana log or Digit a l Input Mode

(Also see page 20)

This selection is only possible when the digital input (DIGITAL IN)

terminal setting has been correctly done for the digital source

currently selected (see page 19).

Notes:

1. Press MENU.

• “INPUT” appears only when the digital input (DIGITAL IN)

terminal setting has been correctly done for the digital source

currently selected. (See page 19.)

• The on-screen display will disappear if no operation is done for

about 1 minute.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

2. Press 5 / ∞ to move

• The on-screen display is shown in black and white.

to “INPUT.”

3. Press 2 / 3 to select

the analog or digital

input mode you want.

4. When you finish, press

EXIT.

The menu disappears from the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

For Surround mode, Surround mode with DAP

mode:

Adjus t ing t he Equa liza t ion P a t t er n

(Also see page 15)

“TEST TONE”:

Output a test tone.

1. Press MENU.

“L/R BALANCE”: Adjust the right and left balance

of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output

level. *

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

“REAR L LEVEL”: Adjust the left rear speaker output

level. **

“REAR R LEVEL”: Adjust the right rear speaker

output level. **

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

The SOUND CONTROL menu appears.

“SUBWFR LEVEL”: Adjust the subwoofer output

level. ***

For DAP mode:

3. Press 5 / ∞ to move

to “DIGITAL EQ,”

then press 2 / 3.

The DIGITAL EQ menu

appears.

“L/R BALANCE”: Adjust the right and left balance

of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output

level. *

“REAR L LEVEL”: Adjust the left rear speaker output

level. **

“REAR R LEVEL”: Adjust the right rear speaker

output level. **

4. Press 5 / ∞ to move

to the frequency you

want to adjust.

5. Press 2 / 3 to adjust

“SUBWFR LEVEL”: Adjust the subwoofer output

level. ***

the frequency level you

want.

The frequency level changes

by 2 dB from –8 dB to +8 dB.

For 5 CH/4 CH Stereo mode:

“L/R BALANCE”: Adjust the right and left balance

of the front speakers.

6. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

“CENTER LEVEL”: Adjust the center speaker output

level. ****

“REAR L LEVEL”: Adjust the left rear speaker output

level. **

Adjus t ing t he S ur r ound a nd DS P M odes

(Also see pages 27 – 34)

“REAR R LEVEL”: Adjust the right rear speaker

output level. **

“SUBWFR LEVEL”: Adjust the subwoofer output

level. ***

You can use a Surround mode with a DAP mode, but not with the

5 CH/4 CH Stereo mode and 3D PHONIC mode.

1. Press MENU.

For 3D-PHONIC mode:

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

“L/R BALANCE”: Adjust the right and left balance

of the front speakers.

“CENTER LEVEL”: Adjust the center speaker output

level. *

“SUBWFR LEVEL”: Adjust the subwoofer output

level.***

2. Select Surround mode and/or DSP mode you like

to adjust (see page 36).

3. Press 5 / ∞ to move

to “SOUND

For Surround off and DSP OFF:

“L/R BALANCE”: Adjust the right and left balance

of the front speakers.

CONTROL,” then

press 2 / 3.

“SUBWFR LEVEL”: Adjust the subwoofer output

level.***

The SOUND CONTROL

menu appears.

Notes:

4. Press 5 / ∞ to move

to “LEVEL

You cannot select “CENTER LEVEL” when “CTR SPK” is set

to “NONE” (see page 17).

** You cannot select “REAR L LEVEL” and “REAR R LEVEL”

when “REAR SPK” is set to “NONE” (see page 17).

*** You cannot select “SUBWFR LEVEL” when “SUBWOOFER”

is set to “NO” (see page 17).

ADJUST,” then press

2 / 3.

The LEVEL ADJUST menu

appears.

****You cannot select “CENTER LEVEL” when 4 CH Stereo

mode is selected.

5. Press 5 / ∞ to move

to the item you want to

set or adjust, then press 2 / 3.

6. Press EXIT once.

On these adjustment menus, you can do the followings:

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Press 5 / ∞ to move

5. Press 5 / ∞ to move

to the item you want to

set or adjust, then press 2 / 3.

to “EFFECT ADJUST,”

On this adjustment menu, you can do the following:

then press 2 / 3.

The EFFECT ADJUST menu

appears.

“L/R BALANCE”:

“CENTER LEVEL”:

“REAR L LEVEL”:

“REAR R LEVEL”:

“SUBWFR LEVEL”:

Adjust the right and left balance

of the front speakers.

Adjust the center speaker output

level.

Adjust the left rear speaker output

level.

Adjust the right rear speaker

output level.

Adjust the subwoofer output level.

8. Press 5 / ∞ to move

to the item you want to

set or adjust, then press

2 / 3.

On these adjustment menus,

you can do the followings.

6. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

For Surround mode:

“CENTER TONE”: Select the center tone level. *

Lis t ening a t Night — M idnight M ode

(Also see page 13)

For DAP mode, Surround mode with DAP:

“EFFECT LEVEL”: Adjust the surround effect level.

1. Press MENU.

“ROOM SIZE”:

“LIVENESS”:

Adjust the room size effect.

Adjust the liveness level.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

“CENTER TONE”: Select the center tone level. *

For 5 CH Stereo mode:

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

“CENTER TONE”: Select the center tone level.

The SOUND CONTROL menu appears.

For 3D-PHONIC mode:

“EFFECT LEVEL”: Adjust the surround effect level.

“CENTER TONE”: Select the center tone level. *

3. Press 5 / ∞ to move

to “MIDNIGHT

MODE.”

Note:

4. Press 2 / 3 to select

the mode you want to

use.

•

You cannot select “EFFECT ADJUST” in step 7, when both of

the Surround and DSP modes are deactivated.

You cannot select “CENTER TONE” when “CTR SPK” is set to

“NONE” (see page 17).

5. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

9. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

At t enua t ing t he Input S igna l

(Also see page 14)

Adjus t ing t he DVD M ULTI P la yba ck M ode

(Also see page 35)

1. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

1. Select DVD MULTI as the playing source.

Press DVD MULTI.

2. Press MENU.

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the MENU.

The SOUND CONTROL menu appears.

3. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

3. Press 5 / ∞ to move

to “INPUT ATT.”

The SOUND CONTROL menu appears.

4. Press 2 / 3 to select

the Input Attenuator

mode “ATT ON” or

“NORMAL.”

4. Press 5 / ∞ to move

to “LEVEL ADJUST,”

then press 2 / 3.

The LEVEL ADJUST menu

appears.

5. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

S elect ing t he Line Dir ect Funct ion

Oper a t ing t he Tuner (Also see pages 22 and 23)

(Also see page 14)

1. Select FM or AM as the playing source.

Press FM/AM.

1. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

2. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

3. Press 5 / ∞ to move

to “TUNER

The SOUND CONTROL menu appears.

3. Press 5 / ∞ to move

CONTROL,” then

to “LINE DIRECT.”

press 2 / 3.

The TUNER CONTROL

menu appears.

4. Press 2 / 3 to turn the

line direct function

“ON” or “OFF.”

4. Press 5 / ∞ to move

to the item you want to

set or adjust, then press

5. When you finish, press

EXIT repeatedly until the menu disappears from

the TV.

2 / 3.

On the TUNER CONTROL

menu, you can do the

following:

S elect ing t he Ba s s Boos t Funct ion

(Also see page 14)

1. Press MENU.

“BAND”:

Select the band.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

“PRESET CH”:

“FREQUENCY”:

“FM MODE”:

Select a preset channel station.

Tune in a station manually.

Select the FM reception mode.*

“PRESET MEMORY”: See “Storing the Preset Stations.”

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

Note:

* Not displayed when an AM station is selected.

The SOUND CONTROL menu appears.

5. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

3. Press 5 / ∞ to move

to “BASS BOOST.”

4. Press 2 / 3 to turn the

bass boost function

“ON” or “OFF.”

S t or ing t he P r es et S t a t ions (Also see page 22)

1. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

5. When you finish, press

EXIT repeatedly until

the menu disappears from the TV.

2. Press 5 / ∞ to move

to “TUNER

CONTROL,” then press 2 / 3.

Act iva t ing t he S ubwoofer S ound

The TUNER CONTROL menu appears.

(Also see page 14)

3. Tune into a station on the TUNER CONTROL

menu, referring to “Operating the Tuner”.

1. Press MENU.

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

4. Press 5 / ∞ to move

to “PRESET

MEMORY,” then press

2 / 3.

2. Press 5 / ∞ to move

to “SOUND

CONTROL,” then press 2 / 3.

moves to “PRESET CH”

and the channel number starts

flashing.

The SOUND CONTROL menu appears.

3. Press 5 / ∞ to move

to “SUBWOOFER.”

5. Press 2 / 3 to select a preset station number you

want.

4. Press 2 / 3 to turn the

subwoofer output

6. Press SET to store the setting.

“ON” or “OFF.”

The selected channel number stops flashing.

5. When you finish, press

EXIT repeatedly until the menu disappears from

the TV.

7. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING 2 menu

S et t ing t he Ba s ic S et t ing It em s

“DIGITAL 1/2/3/4”: Set the digital input terminal 1/2/3/4

(see page 19).

(Also see pages 16 – 21)

1. Press MENU.

“VIDEO DVD”:

“VIDEO DBS”:

“LFE ATT”:

Set the video input terminal for the

DVD player (see page 16).

Set the video input terminal for the

DBS tuner (see page 16).

Set the low frequency effect attenuator

level (see page 19).

The MENU appears on the TV.

• Pressing one of the 5 / ∞ / 2 / 3 buttons also displays the

MENU.

2. Press 5 / ∞ to move

to “SETTING,”

“FL DISPLAY”:

Shows the disc text information on the

display (see page 21).

then press 2 / 3.

The SETTING 1 appears.

Notes:

3. Press 5 / ∞ to move

to the item you

* You cannot select “CNTR DELAY” when “CTR SPK” is set to

“NONE” (see page 17).

want to set or adjust,

then press 2 / 3.

**You cannot select “REAR DELAY” when “REAR SPK” is set to

“NONE” (see page 17).

• To go to the SETTING 2

4. When you finish, press EXIT repeatedly until the

menu disappears from the TV.

menu, move

to “NEXT

PAGE,” then press 2 / 3.

• To go back to the SETTING

1 menu, move

“PREVIOUS PAGE,” then

press 2 / 3.

On the SETTING 1 and 2

menus, you can do the

following:

SETTING 1 menu

“SUBWOOFER”: Set the subwoofer information (see

page 17).

“FRONT SPK”:

Set the front speaker information (see

page 17).

“CENTER SPK”: Set the center speaker information (see

page 17).

“REAR SPK”:

Set the rear speaker information (see

page 17).

“CNTR DELAY”: Adjust the delay time of the center

speaker output (see page 18). *

“REAR DELAY”: Adjust the delay time of the rear

speaker output (see page 18). **

“CROSSOVER”:

Set the crossover frequency

(see page 18).

“ONE TOUCH OPR”: Set the one touch operation

(see page 21).

Download from Www.Somanuals.com. All Manuals Search And Download.

COM P U LINK Rem ot e Cont r ol S ys t em

The COMPU LINK remote control system allows you to operate J VC audio components through the remote sensor on

the receiver.

To use this remote control system, you need to connect JVC audio

components through the COMPU LINK (SYNCHRO) jacks (see

below) in addition to the connections using cables with RCA pin

plugs (see pages 5 and 6).

• Make sure that the AC power cords of these components are

unplugged before connection. Plug the AC power cords only after

all connections are complete.

Aut om a t ic S our ce S elect ion

When you press the play (3) button on a connected component or

on its own remote control, the receiver automatically turns on and

changes the source to the component. On the other hand, if you

select a new source on the receiver or on the remote control, the

selected component begins playing immediately.

In both cases, the previously selected source continues playing

without sound for a few seconds.

CD player

Aut om a t ic P ower On/ Off (S t a ndby): only pos s ible

wit h t he COM P U LINK-3 a nd COM P U LINK--4

connect ion

CD recorder

The connected components turn on and off (standby) along with the

receiver.

When you turn on the receiver, one of the connected components

will turn on automatically, depending on which component has been

previously selected.

When you turn off the receiver, the connected components will turn

off (standby).

Cassette deck

MD recorder

S ynchr onized Recor ding

COMPU LINK – 4

(SYNCHRO)

Synchronized recording means the cassette deck (or MD recorder)

starts recording as soon as a CD or a record begins playing.

To use synchronized recording, follow these steps:

Turntable

1. Put a tape in the cassette deck (or an MD in the

MD recorder), and a disc in the CD player (or a

record on the turntable).

2. Press the record (¶) button and the pause (8)

button on the cassette deck (or MD recorder) at

Notes:

the same time.

• There are four versions of COMPU LINK remote control system.

This receiver is equipped with the fourth version — COMPU LINK-

4. This version is added systematic operations with the CD recorder

to the previous version — COMPU LINK-3.

• If your audio component has two COMPU LINK jacks, you can use

either one. If it has only one COMPU LINK jack, connect it so that it

is the last item in the series of components. (For example, the

turntable or CD player in the diagram above.)

This puts the cassette deck (or MD recorder) into recording

pause.

If you do not press the record (¶) button and pause (8) button at

the same time, the synchronized recording feature will not

operate.

3. Press the play (3) button on the CD player or on

• To operate the cassette deck or MD recorder using the COMPU

LINK remote control system, set the source name correctly. (See

page 16.)

the turntable.

The source changes on the receiver, and as soon as play starts,

the cassette deck (or MD recorder) starts recording. When the

play ends, the cassette deck (or MD recorder) enters recording

pause, and stops about 4 seconds later.

• Refer also to the manuals supplied with your audio components.

This remote control system allows you to use four functions listed

below.

Notes:

Rem ot e Cont r ol t hr ough t he Rem ot e S ens or on t he

Receiver

• During synchronized recording, the selected source cannot be

changed.

• If the power of any component is shut off during synchronized

recording, the COMPU LINK remote control system may not

operate properly. In this case, you must start again from the

beginning.

You can control the connected audio components through the remote

sensor on the receiver using this remote control. Aim the remote

control directly at the remote sensor on the receiver. For details, see

pages 49 and 50.

Download from Www.Somanuals.com. All Manuals Search And Download.

TEXT COM P U LINK Rem ot e Cont r ol S ys t em

The TEXT COMPU LINK remote control system has been developed to deal with the disc information recorded in the

CD Text* and MDs. Using these information in the discs, you can operate the CD player or MD recorder equipped with

the TEXT COMPU LINK remote control system through the receiver.

CONNECTIONS :

FUNCTIONS :

This remote control system allows you to use the functions listed

below.

To use this remote control system, you need to connect the CD

player and/or MD recorder you want to operate, following the

procedures below.

Dis pla ying t he Dis c Infor m a t ion on t he TV s cr een

Disc information such as its performer and disc title (and track titles

only when a CD Text is selected) is shown on the TV screen.

1. If you have already plugged your CD player, MD

recorder, and this receiver into the AC outlets,

unplug their AC power cords first.

Dis c S ea r ch: Only for CD P la yer

This remote control system can allow you to search for discs by the

performer, disc title, and music genre.

With this disc search, you can easily find the disc you want to play.

2. Connect your CD player, MD recorder, and this

receiver as follows, through the COMPU LINK

jacks and TEXT COMPU LINK jacks.

Dis c Tit le Input :

1) COMPU LINK jacks: Use the cables with the monaural

If your CD player or MD recorder has the disc memory function,

you can input the following information about the normal audio CDs

or MDs on the TV screen.

• For CDs: Performer, disc title, and music genre

• For MDs: Disc title and song titles

mini-plugs (not supplied with this receiver).

CD player

MD recorder

*What is a CD Text?

In a CD Text, some information about the disc (its disc title, performer,

composer, arranger, etc.) is recorded.

Notes:

COMPU LINK – 4

(SYNCHRO)

• If your audio component has two COMPU LINK jacks, you can use

either one. If it has only one COMPU LINK jack, connect it so that it

is the last item in the series of components. (For example, the CD

player in the diagram in the left column.)

2) TEXT COMPU LINK jacks: Use the cables with the

stereo mini-plugs (not supplied with this receiver).

• If your audio component has two TEXT COMPU LINK jacks, you

can use either one. If it has only one TEXT COMPU LINK jack,

connect it so that it is the last item in the series of components. (For

example, the CD player in the diagram in the left column.)

• “TEXT COMPULINK SOURCE NOT CONNECTED” appears on the

display in the following cases:

– When the connections explained in the left column are not

correctly done.

– When you try to use the TEXT COMPULINK function a few

seconds after you turn on the connected equipment. This is not a

malfunction of the units.

CD player

MD recorder

TEXT

COMPU LINK

• Refer also to the manuals supplied with your CD player or MD

recorder.

3. Connect your CD player, MD recorder and this

receiver, using the cables with RCA pin plugs (see

pages 5 and 6).

IMPORTANT:

If you turn on the receiver before turning on the other components

after connecting the components, the TEXT COMPU LINK remote

control system does not work correctly.

4. Plug the AC power cords of these components

above into the AC outlets.

If this happens:

1. Turn off all the components including this receiver.

2. Turn on the connected components.

3. Turn on this receiver.

5. When turning on these components for the first

time, turn on the connected components first,

then turn on this receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Source name: CD or MD

2 Select or , then press SET to change the disc.

3 Track numbers and track titles.

OP ERATIONS :

To use this remote control system, you need to connect the TV to the

MONITOR OUT jack on the rear panel (see page 7), and set the

TV’s input mode to the proper position to which the receiver is

connected. Make sure you have connected the CD player or

MD recorder equipped with the TEXT COMPU LINK

remote control system. If not, you cannot use the

following functions.

• When you move

to a track number, you can

change the track information by pressing 2 / 3. Each

time you press the button, track information alternates

between its track title and its performer. (You can also

start playing the track by pressing SET.)

4 Select this (move

in front), then press SET to go to

the DISC SEARCH screen (see page 44).

5 Select this (move

in front), then press SET to go to

the TITLE INPUT screen (see page 45).

6 This appears only when a CD Text is selected.

7 Disc information such as the disc title, performer, and

music genre.

On-Screen Operation buttons (on the remote control)

When you press TEXT

When this is selected (

in front), you can change the

DISPLAY, “MENU” appears

on the display window for

disc information by pressing 2 / 3. Each time you press

the button, disc information (see “Note on 7”) changes.

CATV/DBS VCR 1

AUDIO

about 10 seconds.

POWER

8 Select

, then press SET to change the track.

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

TV/DBS

VCR 1

VIDEO

VCR 2

9 Usable buttons and their functions for the current

selection.

TAPE/MD

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

Indication here will be changed according to what is

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

currently selected (

in front) on the screen. See “Note

MIDNIGHT

CTRTONE

MODE

SOUND

MUTING

TEST

LIVENESS

ENTER

on 9.”

SUBWFR

L/R BAL

CENTER

∗

7/P

DIGITALEQ

REAR L

REAR R

∗

RETURN

+10

100

PLAY

FM MODE

Note on 7:

EXIT

CATV/DBS

CONTROL

BAL L

∗

CH/ LEVEL TV VOL

VOLUME

∗

The following information will appear on the display:

• For CD Texts — Disc title, Performer, Genre, Song writer,

Composer, Arranger, Message

Only recorded information will be shown. If there is no data, “NO

DATA” will appear.

TV/VIDEO

−

BAL R

TEXT

DISPLAY

∗

/REW

FF/

PAUSE

SET

PLAY

EXIT

TEXT

DISPLAY

/REW

FF/

PAUSE

SET

REC

PAUSE

DOWN – TUNING

–

DOWN – TUNING – UP

CONTROL

STOP

• For MDs — Disc title

RM-SRX8010J

A/V CONTROL RECEIVER

If there is no data, “NO DATA” will appear.

STOP

Note on 9:

For example, the SET button will be used to start play (PLAY), to go to

the next screen (ENTER), and to determine the selection (ENTER).

To exit fr om t he Dis c infor m a t ion s cr een:

Press EXIT.

Notes:

• The on-screen display will disappear in the following cases:

– if no operation is done for about 10 minutes.

– if you do any operation other than explained in this section.

• To control the MD recorder using the TEXT COMPU LINK remote

control system, you have to change the source name shown on the

display from “TAPE” to “MD.” (See page 16.)

S howing t he Dis c Infor m a t ion on t he TV

S cr een

Press TEXT DISPLAY while “CD” or “MD” is

selected as the source.

The Disc Information screen appears on the TV.

• Some special characters and marks cannot be displayed correctly.

• The on-screen display is shown in black and white.

Download from Www.Somanuals.com. All Manuals Search And Download.

S ea r ch for a dis c by it s dis c t it le:

S ea r ching for a Dis c (Only for t he CD pla yer )

S ea r ch for a dis c by it s per for m er :

1. Press TEXT DISPLAY while “CD” is selected as

the source.

1. Press TEXT DISPLAY while “CD” is selected as

the source.

The Disc Information screen appears on the TV.

2. Press 5 / ∞ to move

to “SEARCH,” then

2. Press 5 / ∞ to move

press SET.

The DISC SEARCH screen

appears.

to “SEARCH,” then

press SET.

The DISC SEARCH screen

appears .

3. Press 5 / ∞ to move

to “DISC TITLE,”

then press SET.

The DISC TITLE SEARCH

screen appears.

3. Press 5 / ∞ to move

to “PERFORMER”,

then press SET.

The PERFORMER SEARCH

screen appears.

4. Press 5 / ∞ / 2 / 3 to move

in front of the

first character of the disc title you want to search

for, then press SET.

4. Press 5 / ∞ / 2 / 3 to move

in front of the

first character of the performer you want to

search for, then press SET.

To correct the incorrect entry, press 5 / ∞ / 2 / 3 to move

in front of the correct character, then press SET.

To correct the incorrect entry, press 5 / ∞ / 2 / 3 to move

in front of the correct character, then press SET.

Note:

Symbols such as @, # or $ cannot be available for search.

Note:

Symbols such as @, # or $ cannot be available for search.

5. Press SET again.

Disc search starts, then the

SEARCH RESULT screen,

showing the disc titles,

appears.

5. Press SET again.

Disc search starts, then the

SEARCH RESULT screen,

showing the performers,

appears.

6. On the SEARCH RESULT screen, you can do the

following:

6. On the SEARCH RESULT screen, you can do the

following:

• Changing the indication of the disc information: Press 5 /

∞ to move

to a searched disc, then press 2 / 3. Each time

• Changing the indication of the disc information: Press 5 /

you press 2 / 3, the disc information alternates between its

∞ to move

to a searched disc, then press 2 / 3. Each time

disc title and its performer.

you press 2 / 3, the disc information alternates between its

• Starting a disc play and going to the Disc Information

performer and its disc title.

screen (see page 43): Press 5 / ∞ to move

disc, then press SET.

to a searched

• Starting a disc play and going to the Disc Information

screen (see page 43): Press 5 / ∞ to move

disc, then press SET.

to a searched

• Showing unseen disc information (if more than 5 discs are

listed as a result of the search): Press 5 / ∞ until they

appear.

• Showing unseen disc information (if more than 5 discs are

listed as a result of the search): Press 5 / ∞ until they

appear.

• Going back to the DISC TITLE SEARCH screen: Press

EXIT.

• Going back to the PERFORMER SEARCH screen: Press

EXIT.

Download from Www.Somanuals.com. All Manuals Search And Download.

S ea r ch for a dis c by it s genr e:

Ent er ing t he Dis c Infor m a t ion

1. Press TEXT DISPLAY while “CD” is selected as

the source.

For t he CD P la yer wit h t he dis c m em or y funct ion:

You can use the disc memory function through this receiver.

The disc information (its performer, disc title, and music genre) of

normal audio CDs will be stored into the memory built in the CD

player.

For the disc memory function, refer to the manual supplied with

your CD player.

• The performer, disc title, and music genre information are usually

recorded in a CD Text. However, if a CD Text has no genre

information recorded in the disc itself, you can input its music

genre by yourself.

The Disc Information screen appears on the TV.

2. Press 5 / ∞ to move

to “SEARCH,” then

press SET.

The DISC SEARCH screen

appears.

3. Press 5 / ∞ to move

to “GENRE”, then

Note:

press SET.

The GENRE SEARCH screen

appears.

You can enter the TITLE INPUT screens for a CD Text and input its

titles. However, you cannot store the titles you have input for a CD

Text.

Example: Entering the following information for Disc 1

Performer: “MICHAEL”

Disc title: “MY FAVORITE”

4. Press 5 / ∞ to move

to the genre you

want to search for, then

press SET.

To show the unseen genres,

press 5 / ∞ until they appear.

1. Press TEXT DISPLAY while “CD” is selected as

the source.

The Disc Information screen appears on the TV.

Disc search starts, then the

SEARCH RESULT screen,

showing the disc titles,

appears.

2. Press 5 / ∞ to move

to “TITLE INPUT,”

then press SET.

The TITLE INPUT/

PERFORMER screen appears.

5. On the SEARCH RESULT screen, you can do the

following:

• Changing the indication of the disc information: Press 5 /

3. Press 5 / ∞ / 2 / 3 to

∞ to move

to a searched disc, then press 2 / 3. Each

move

in front of a character you want, then

time you press 2 / 3, the disc information alternates between

its disc title and its performer.

press SET to enter the character.

• If the current CD is a CD Text, go to step 5 without entering

the performer.

• Starting a disc play and going to the Disc Information

screen (see page 43): Press 5 / ∞ to move

disc, then press SET.

to a searched

To use the lower case letters, press 5 / ∞ / 2 / 3 to move

, then press SET.

• Showing unseen disc information (if more than 5 discs are

listed as a result of the search): Press 5 / ∞ until they

appear.

To use the upper case letters again, press 5 / ∞ / 2 / 3 to

move to , then press SET.

• Going back to the GENRE SEARCH screen: Press EXIT.

Continued to the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

For t he M D r ecor der :

4. Repeat step 3 until you

finish putting a

You can write the disc information (disc title and song titles) into the

disc. You can only write the song title for the song currently

selected.

• If you have the CD-MD combination deck, you can also enter the

disc information (its performer, disc title, and its music genre) of

normal audio CDs into the memory built in the CD-MD

combination deck. (To do this, follow the procedure of “For the

CD Player with the disc memory function.”)

performer name (up to

32 characters).

To insert a space, press 5 / ∞

/ 2 / 3 to move

then press SET.

To correct an incorrect character:

1) Press 5 / ∞ / 2 / 3 to move

to + or =, then press

• If you change the disc or song title with more than 32 characters,

the characters following 32nd will be erased from the title.

SET until the incorrect character is selected.

2) Press 5 / ∞ / 2 / 3 to move

to erase the character.

, then press SET

1. Press TEXT DISPLAY while “MD” is selected as

the source.

3) Press 5 / ∞ / 2 / 3 to move

in front of the correct

character, then press SET to enter the correct character.

The Disc Information screen appears on the TV.

5. Press 5 / ∞ / 2 / 3 to

2. Press 5 / ∞ to move

move

to “DISC 1:

to “TITLE INPUT,”

MICHAEL (in this

example),” then press

SET.

then press SET.

The DISC TITLE INPUT

screen appears.

The TITLE INPUT: DISC

TITLE screen appears.

3. Enter the title,

referring to steps 3 and

4 of “For the CD Player

with the disc memory

function.”

• You can enter up to 32

6. Enter the disc title,

referring to steps 3 and

• If the current CD is a CD

Text, go to the next step

without entering the disc

title.

characters for the disc title.

4. Press 5 / ∞ / 2 / 3 to

move

to the disc title

7. Press 5 / ∞ / 2 / 3 to

you have just entered,

then press SET.

The disc title is stored into the

memory, and the SONG

TITLE INPUT screen for the

currently selected song

move

to “DISC 1:

MY FAVORITE (in

this example),” then

press SET.

The TITLE INPUT: DISC 1

GENRE screen appears.

appears.

• You can enter a song title for the song currently selected.

8. Press 5 / ∞ to move

to the genre you want,

then press SET.

5. Enter the song title, referring to steps 3 and 4 of

“For the CD Player with the disc memory

function.”

The Disc Information screen appears again.

To show the unseen genres, press 5 / ∞ until they appear.

• You can enter up to 32 characters for the song title.

6. Press 5 / ∞ / 2 / 3 to move

to the song title

you have just entered, then press SET.

The song title is stored into the memory, and the Disc

Information screen appears again.

Download from Www.Somanuals.com. All Manuals Search And Download.

AV COM P U LINK Rem ot e Cont r ol S ys t em

The AV COMPU LINK remote control system allows you to operate J VC video components (TV, VCR, and DVD player)

through the receiver.

This receiver is equipped with the AV COMPU LINK-III, which added a function to operate JVC video components through the video

components terminals. To use this remote control system, you need to connect the video components you want to operate, following the

diagrams below and the procedure on the next page.

CONNECTIONS 1 : AV COM P U LINK Connect ion

VCR 1

DVD player

VHS

DVD

CAUTION:

COMPU LINK

You can only connect to the TV

with the AV COMPU LINK EX or

AV COMPU LINK III terminal.

DO NOT connect to the TV with

AV COMPU LINK RECEIVER/

AMP terminal.

COMPU LINK III

COMPU LINK

COMPU LINK EX

COMPU LINK III

IMPORTANT:

The AV COMPU LINK remote control system cannot control the

DBS tuner connected to the TV SOUND/DBS and DBS component

video terminals, and video components connected to the VIDEO

and VCR 2 terminals on the receiver.

Notes:

• When connecting the receiver and a TV with the AV COMPU LINK EX terminal by using a component video cable, you cannot use Automatic

Selection of TV’s Input Mode (see page 48).

• When connecting only the VCR 1 or DVD player to this receiver, connect it directly to the receiver using cables with the monaural mini-plugs.

• Refer also to the manuals supplied with your video components.

CONNECTIONS 2 : Video Ca ble Connect ion

This receiver is equipped with three types of the video terminals — S-video, composite video, or component video, and the signals coming

into this receiver through one type of video terminals can output only through the same type of the terminal. So you need to connect the VCR

and/or DVD player to the TV using one of the following three ways:

CASE 1

When connecting the source equipment to the receiver using the S-video terminals, connect also this

receiver to the TV’s Video Input 1 terminal using S-video cables.

Source

Equipment

RX-8010VBK

S-video cable

To Video Input 1

Note:

If you connect the DVD player and the DBS tuner to this receiver using the S-video terminals, change the video input

terminal setting to "S/C" (see page 16).

When connecting the source equipment to the receiver using the composite video terminals, connect also

this receiver to the TV's Video Input 2 terminal (composite video input) using composite video cables.

CASE 2

Source

Equipment

RX-8010VBK

Composite

video cable

Composite

video cable

To Video Input 2

(Composite)

Note:

If you connect the DVD player and the DBS tuner to this receiver using the composite video terminals, change the video

input terminal setting to "S/C" (see page 16).

CASE 3

When connecting the source equipment to the receiver using the component video terminals, connect also

this receiver to the TV's Video Input 2 terminals (component video input) using component video cables.

Source

Equipment

RX-8010VBK

Component

video cable

Component

video cable

To Video Input 2

(Component)

Note:

If you connect the DVD player and the DBS tuner to this receiver using the video component terminals, change the

video input terminal setting to "COMPNT" (see page 16).

Download from Www.Somanuals.com. All Manuals Search And Download.

One-Touch DVD P la y

1. If you have already plugged your VCR 1 (VCR

connected to the VCR 1 jacks), DVD player, TV

and this receiver into the AC outlets, unplug their

AC power cords first.

Simply by starting playback on the DVD player, you can enjoy the

DVD playback without setting other switches manually.

• When the DVD player is connected through the analog input jacks

on this receiver (and analog input is selected), the receiver

automatically turns on and changes the source to “DVD” or

“DVD MULTI.”

• When the DVD player is connected through the digital input

terminal on this receiver (and digital input is selected), the

receiver automatically turns on and changes the source to “DVD

DGTL.”

2. Connect your VCR 1, DVD player, TV and this

receiver as follows, using the cables with the

monaural mini-plugs (not supplied).

• See “CONNECTIONS 1” on the previous page.

The TV automatically turns on and changes the input mode to the

appropriate position so that you can view the playback picture.

3. Connect the audio input/output jacks on VCR 1,

DVD player, TV and this receiver using the cables

with RCA pin plug.

Aut om a t ic S elect ion of TV’s Input M ode

• See pages 6 and 7.

• When you select “TV” as the source to play on the receiver, the

TV automatically changes the input mode to the TV tuner so that

you can watch TV.

• When you select “DVD,” “DVD MULTI,” “VCR 1,” “VCR 2,”

“VIDEO” or “DBS” as the source to play on the receiver, the TV

automatically changes the input mode to the appropriate position

(either Video Input 1 or Video Input 2) so that you can view the

playback picture.

4. Connect the video input/output jacks on VCR 1,

DVD player, TV and this receiver, using the

cables with RCA pin plug, with

S-video plug or with component video plugs.

• See “CONNECTIONS 2” on the previous page.

5. Plug the AC power cords of the components into

the AC outlets.

Notes:

• When connecting a TV with the AV COMPU LINK EX terminal to

this receiver, you cannot use a component video cable (as case 3

on page 47). Connect the TV using a S-video or composite video

cable (as cases 1 and 2).

• When you select “TV” as the source on the receiver, you cannot

see the menu on the TV screen since the AV COMPU LINK remote

control system automatically changes the TV’s input mode to the

TV tuner.

6. When turning on the TV for the first time after

the AV COMPU LINK connection, turn the TV

volume to the minimum using the TV volume

control on the TV.

7. Turn on the other connected components first,

If you do not mind stopping listening to the TV sounds, you can

then show the on-screen displays after changing the TV’s input

mode to the appropriate position the receiver is connected to.

then turn on this receiver.

• When turning on the VCR 1, use the remote control supplied

with this receiver (press VCR 1 POWER).

The AV COMPU LINK remote control system allows you to use the

five basic functions listed below.

Aut om a t ic P ower On/ Off

The TV, VCR 1 (the VCR connected to the VCR 1 jacks), and DVD

player turn on and off along with the receiver.

When you turn on the receiver;

• If the previously selected source is “VCR 1,” the TV and VCR 1

will turn on automatically.

• If the previously selected source is “VIDEO,” “VCR 2,” or “TV”

or “DBS,” only the TV will turn on automatically.

• If the previously selected source is “DVD” or “DVD MULTI,” the

TV and DVD player will turn on automatically.

When you turn off the receiver, the TV, VCR 1 and the DVD player

will turn off.

Rem ot e Cont r ol of t he TV, DVD pla yer, a nd VCR

Us ing This Rem ot e Cont r ol

See page 51 for details.

• Aim the remote control directly at the remote sensor on each

target component.

One-Touch Video P la y

Simply by inserting a video cassette without its safety tab into the

VCR 1 (the VCR connected to the VCR 1 jacks), you can enjoy the

video playback without setting other switches manually. The

receiver automatically turns on and changes the source to “VCR 1.”

The TV automatically turns on and changes the input mode to the

position so that you can view the playback picture.

Note:

If you turn off the receiver while recording on the VCR 1, the VCR 1

will not turn off, but continue recording.

When you insert a video cassette with its safety tab, press the play

(3) button on the VCR 1 or on the remote control. So, you can get

the same result.

Download from Www.Somanuals.com. All Manuals Search And Download.

Oper a t ing J VC’s Audio/ Video Com ponent s

You can operate J VC’s audio and video components with this receiver’s remote control, since control signals for J VC

components are preset in the remote control.

Tuner

Oper a t ing Audio Com ponent s

You can always perform the following operations:

IMPORTANT:

FM/AM:

Alternates between FM and AM.

To operate JVC’s audio components using this remote control:

• You need to connect JVC audio components through the COMPU

LINK (SYNCHRO) jacks (see page 41) in addition to the

connections using cables with RCA pin plugs (see pages 5 and 6).

• Aim the remote control directly at the remote sensor on the

receiver.

• If you use the buttons on the front panel or the menu function to

choose a source, the remote control will not operate that source.

To operate a source with the remote control, the source must be

selected using source selecting buttons on the remote control.

• To operate the cassette deck or MD recorder using the COMPU

LINK remote control system, set the source name correctly. (See

page 16.)

After pressing FM/AM, you can perform the following operations:

1 – 10, +10:

Selects a preset channel number

directly.

For channel number 5, press 5.

For channel number 15, press +10,

then 5.

For channel number 20, press +10, then

10.

TUNING UP 3/DOWN 2: Tunes into stations.

FM MODE:

Changes the FM reception mode.

• Refer also to the manuals supplied with your components.

S ound cont r ol s ect ion (Am plifier )

You can always perform the following operations:

SURROUND ON/OFF:

DSP MODE:

Turns on or off the Surround modes

– Dolby Pro Logic, Dolby Digital,

and DTS Digital Surround.

Selects the DSP modes.

After pressing SOUND, you can perform the following operations:

SUBWFR then LEVEL +/ –: Adjusts the subwoofer output level.

CATV/DBS VCR 1

AUDIO

CENTER then LEVEL +/ –: Adjusts the center speaker output

POWER

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

level.

TV/DBS

VCR 1

VIDEO

VCR 2

REAR L then LEVEL +/ –: Adjusts the left rear speaker output

TAPE/MD

level.

REAR R then LEVEL +/ –: Adjusts the right rear speaker output

level.

DIGITAL EQ then LEVEL+/ –:Selects the audio band and adjusts

its frequency level.

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

MIDNIGHT

CTRTONE

TEST

LIVENESS

MODE

SOUND

MUTING

ENTER

SUBWFR

L/R BAL

CENTER

∗

7/P

EFFECT:

TEST:

CTR TONE:

ROOM SIZE:

LIVENESS:

Selects the effect level.

Turns on or off the test tone output.

Selects the center tone.

Selects the room size.

DIGITALEQ

REAR L

REAR R

∗

+10

100

RETURN

FM MODE

CATV/DBS

CONTROL

BAL L

∗

CH/ LEVEL TV VOL

VOLUME

∗

TV/VIDEO

−

Selects the liveness.

BAL R

∗

PLAY

EXIT

TEXT

DISPLAY

/REW

FF/

PAUSE

SET

Note:

REC

PAUSE

DOWN – TUNING – UP

After adjusting sounds, press the corresponding source selecting

button to operate your target source by using the 10 keys; otherwise,

the 10 keys cannot be used for operating your target source.

CONTROL

STOP

RM-SRX8010J

A/V CONTROL RECEIVER

CD pla yer

Note:

After pressing CD, you can perform the following operations on the

CD player:

When you press one of the following buttons mentioned in

this section, the operation mode appears on the display

window for about 10 seconds. For example, the above

illustration shows that you have pressed CD.

3 PLAY:

Starts playing.

Returns to the beginning of the current

(or previous) track.

Buttons

FM/AM

CDR

PHONO

TAPE/MD

Indications

TUNER

CDR

PHONO

TAPE

¢:

Skips to the beginning of the next track.

Stops playing.

Pauses playing. To release it, press

3 PLAY.

Selects a track number directly.

For track number 5, press 5.

For track number 15, press +10, then 5.

For track number 20, press +10, then 10.

For track number 30, press +10, +10,

then 10.

7 STOP:

8 PAUSE:

1 – 10, +10:

VCR 1

TAPE

CDR

CONTROL (repeatedly)

SOUND

CDDSC

SOUND

Download from Www.Somanuals.com. All Manuals Search And Download.

CD cha nger

CD r ecor der

After selecting “CDDSC” by pressing CONTROL repeatedly, you

can perform the following operations on a CD changer:

After pressing CDR (or selecting “CDR” by pressing CONTROL

repeatedly), you can perform the following operations on a CD

recorder:

3 PLAY:

Starts playing.

Returns to the beginning of the current

(or previous) track.

Skips to the beginning of the next track.

Stops playing.

Pauses playing. To release it, press

3 PLAY.

Selects the number of a disc installed in

a CD changer.

3 PLAY:

Starts playing.

Returns to the beginning of the current

(or previous) track.

Skips to the beginning of the next track.

Stops playing.

Pauses playing. To release it, press

3 PLAY.

Selects a track number directly.

For track number 5, press 5.

For track number 15, press +10, then 5.

For track number 20, press +10, then 10.

For track number 30, press +10, +10,

then 10.

¢:

7 STOP:

8 PAUSE:

¢:

7 STOP:

8 PAUSE:

1 – 6, 7/P:

1 – 10, +10:

After pressing CD, you can perform the following operations on the

CD changer:

1 – 10, +10:

Selects a track number directly.

For track number 5, press 5.

For track number 15, press +10, then 5.

For track number 20, press +10, then 10.

For track number 30, press +10, +10,

then 10.

Notes:

• When you start recording on the CD recorder, use the buttons on

the CD recorder itself or on the remote control supplied with it.

• You can use either CDR or CONTROL to activate the buttons listed

above. If you press CDR, the playing source also changes. On the

other hand, if you press CONTROL repeatedly to select “CDR,” the

playing source does not change.

EXAMPLE:

• Selecting disc number 4, track number 12, and starting playback.

1. Press CONTROL repeatedly until “CDDSC” appears on the

display window, then press 4.

Ca s s et t e deck

2. Press CD, then press +10, 2.

After pressing TAPE/MD (or selecting “TAPE” by pressing

CONTROL repeatedly), you can perform the following operations

on a cassette deck:

If your CD changer is of 200-disc loading capability (except for

XL-MC100 and XL-MC301)

you can do the following operations using the number buttons after

pressing CD.

3 PLAY:

REW:

FF:

7 STOP:

8 PAUSE:

Starts playing.

Fast winds the tape from right to left.

Fast winds the tape from left to right.

Stops operations.

Pauses playing. To release it, press

3 PLAY.

Enters recording pause.

1. Select a disc number.

2. Then select a track number (always enter two digits).

3. Start playback.

EXAMPLES:

REC PAUSE:

• Selecting disc number 3, track number 2, and starting playback.

Press 3, then, 0, 2, then 3 PLAY.

Notes:

• Selecting disc number 10, track number 5, and starting playback.

Press 1, 0, then, 0, 5, then 3 PLAY.

• You can use either TAPE/MD or CONTROL to activate the buttons

listed above. If you press TAPE/MD, the playing source also

changes. On the other hand, if you press CONTROL repeatedly to

select “TAPE,” the playing source does not change.

• Selecting disc number 105, track number 12, and starting

playback. Press 1, 0, 5, then 1, 2 then 3 PLAY.

• When you use a cassette deck, change the source name

connected to TAPE/MD jacks correctly (see page 16).

Tur nt a ble

After pressing PHONO, you can perform the following operations

on a turntable:

M D r ecor der

After pressing TAPE/MD, you can perform the following operations

on the MD recorder:

3 PLAY:

7 STOP:

Starts playing.

Stops operations.

3 PLAY:

Starts playing.

Returns to the beginning of the current

(or previous) track.

¢:

Skips to the beginning of the next track.

Stops playing.

Pauses playing. To release it, press

3 PLAY.

Enters recording pause.

7 STOP:

8 PAUSE:

REC PAUSE:

Note:

When you use an MD recorder, change the source name connected

to TAPE/MD jacks correctly (see page 16).

Download from Www.Somanuals.com. All Manuals Search And Download.

VCR 1 (VCR connect ed t o t he VCR 1 ja cks )

Oper a t ing Video Com ponent s

You can always perform the following operations:

VCR 1 POWER:

Turns on or off the VCR 1.

IMPORTANT:

To operate JVC’s video components using this remote control:

• You need to connect JVC video components through the AV

COMPU LINK jacks (see page 47) in addition to the connections

using cables with RCA pin plugs (see pages 6 and 7).

• Some JVC VCRs can accept two types of the control signals —

remote code “A” and “B.” Before using this remote control, make

sure that the remote control code of the VCR connected to the VCR 1

jacks is set to code “A.”

After pressing VCR 1 (or selecting “VCR 1” by pressing

CONTROL repeatedly), you can perform the following operations

on the VCR 1:

1 – 9, 0:

3 PLAY:

REW:

Selects the TV channels on the VCR.

Starts playing.

Rewinds a tape.

FF:

Fast winds a tape.

– When another JVC VCR is connected to the VCR 2 or VIDEO

terminals, set its remote control code to code “B.” (This remote

control cannot emit the control signals of code “B.”)

• When using the remote control:

– For the DVD player and VCR 1 operations, aim the remote

control directly at the remote sensor on each component, not on

the receiver.

7 STOP:

8 PAUSE:

Stops operations.

Pauses playing. To release it, press

3 PLAY.

Enters recording pause.

Changes the TV channels on the VCR.

REC PAUSE:

CH +/–:

Note:

– For the TV having the AV COMPU LINK EX or AV COMPU

LINK III terminal, aim the remote control directly at the remote

sensor on the TV.

You can use either VCR 1 or CONTROL to activate the buttons listed

above. If you press VCR 1, the playing source also changes. On the

other hand, if you press CONTROL repeatedly to select “VCR 1,” the

playing source does not change.

DVD pla yer

After pressing DVD or DVD MULTI, you can perform the

following operations on a DVD player:

3 PLAY:

Starts playing.

Returns to the beginning of the current

(or previous) track.

Skips to the beginning of the next track.

Stops playing.

Stops playing temporarily. To release it,

press 3 PLAY.

CATV/DBS VCR 1

AUDIO

POWER

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

¢:

7 STOP:

8 PAUSE:

TV/DBS

VCR 1

VIDEO

VCR 2

TAPE/MD

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

MIDNIGHT

CTRTONE

TEST

LIVENESS

MODE

SOUND

MUTING

ROOM

SIZE

ENTER

After pressing DVD or DVD

MULTI, these buttons can be used

for the DVD menu operations.

EFFECT

SUBWFR

L/R BAL

CENTER

∗

7/P

DIGITALEQ

REAR L

REAR R

∗

RETURN

+10

100

FM MODE

TEST

CTR TONE

LIVENESS

CATV/DBS

CONTROL

BAL L

∗

Note:

ENTER

CH/ LEVEL TV VOL

VOLUME

∗

TV/VIDEO

∗L/R BAL

−

BAL R

∗

For detailed menu operations, refer to

the instructions supplied with the

discs or the DVD player.

PLAY

EXIT

TEXT

DISPLAY

/REW

FF/

PAUSE

SET

REC

PAUSE

DOWN – TUNING – UP

CONTROL

STOP

RM-SRX8010J

You can always perform the following operations:

A/V CONTROL RECEIVER

Note:

TV POWER:

TV VOL +/–:

TV/VIDEO:

Turns on or off the TV.

Adjusts the volume.

Sets the input mode (either TV or

VIDEO).

When you press one of the following buttons mentioned in

this section, the operation mode appears on the display

window for about 10 seconds. For example, above illustration

shows that you have pressed VCR 1.

After pressing TV/DBS, you can perform the following operations

on a TV:

Buttons

VCR 1

DVD or DVD MULTI

TV/DBS

Indications

VCR 1

DVD

CH +/–:

1 – 9, 0, 100+:

RETURN:

Changes the channels.

Selects the channels.

VCR 1

TAPE

CDR

CONTROL (repeatedly)

Alternates between the previously

selected channel and the current

channel.

CDDSC

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Other Manufacturers’ Video Equipment

This remote control supplied with the receiver can transmit control

signals for other manufacturers’VCRs, TVs, CATV converters,

DBS tuners and DVD players. By changing the transmittable signals

from preset ones to the other manufacturers’, you can operate the

other manufacturer’s components using this remote control.

To cha nge t he t r a ns m it t a ble s igna ls for

oper a t ing a not her m a nufa ct ur er ’s TV

1. Press and hold TV POWER.

2. Press TV/DBS.

When operating the other manufacturers’ components, refer also to

the manuals supplied with them. To operate these components with

the remote control, first you need to set the manufacturer’s code

each for VCR, TV, CATV converters, DBS tuners and DVD players.

3. Enter manufacturer’s code using buttons 1–9,

and 0.

See the list below to find the code.

After replacing batteries for the remote control, you need to set the

manufactures’ codes again.

4. Release TV POWER.

The following buttons can be used for operating the TV:

TV POWER:

TV VOL +/–:

TV/VIDEO:

Turns on and off the TV.

Adjusts the volume.

Sets the input mode (either TV

or VIDEO).

After pressing TV/DBS, you can perform the following

operations on a TV:

CH +/–:

1 – 10, 0, 100+ (+10): Selects the channels.

The 10 button will function as the

Changes the channels.

CATV/DBS VCR 1

AUDIO

POWER

DVD

DVD MUILTI

CDR

FM/AM

PHONO

USB

TV/DBS

VCR 1

VIDEO

VCR 2

ENTER button if your TV requires

pressing ENTER after selecting a

channel number.

TAPE/MD

SURROUND

ON/OFF

DSP ANALOG/DIGITAL SLEEP

MODE

INPUT

BASS

ROOM

SIZE

LINE DIF.ECT BOOST

EFFECT

MIDNIGHT

Note:

CTRTONE

TEST

LIVENESS

MODE

SOUND

MUTING

ENTER

SUBWFR

L/R BAL

CENTER

Refer to the manual supplied with your TV.

∗

7/P

DIGITALEQ

REAR L

REAR R

∗

RETURN

+10

100

FM MODE

5. Try to operate your TV by pressing TV POWER.

When your TV turns on or off, you have entered the correct

code.

CATV/DBS

CONTROL

BAL L

∗

CH/ LEVEL TV VOL

VOLUME

∗

TV/VIDEO

−

BAL R

∗

If there are more than one code listed for your brand of TV,

try each one until the correct one is entered.

PLAY

EXIT

TEXT

DISPLAY

/REW

FF/

PAUSE

SET

REC

PAUSE

DOWN – TUNING – UP

CONTROL

STOP

Manufacturer

Codes

Manufacturer

Codes

RM-SRX8010J

A/V CONTROL RECEIVER

JVC

00, 02, 13, 14, QUELLE

47, 74

01, 02

52, 53, 54, 55,

56, 57, 58, 59,

60, 61, 62, 63,

64, 65, 66, 67

08, 24, 29, 30,

31, 48

32, 33, 68, 69,

06, 08, 16, 34,

35, 49

AKAI

BLAUPUNKT 03, 04,

FISHER

01, 05

RCA/

Note:

GRUNDIG

HITACHI

IRADDIO

ITT/NOKIA

LOEWE

03, 06, 07

PROSCAN

When you press one of the following buttons mentioned in

this section, the operation mode appears on the display

window for about 10 seconds. For example, the above

illustration shows that you have pressed TV/DBS.

08, 09, 10, 49 SABA

11, 12

SAMSUNG

06, 15, 16

MAGNAVOX 08, 17, 49

METS

MITSUBISHI 08, 18, 19, 20 SHARP

MIVAR 21 SONY

NORDMENDE 22, 23

OKANO 15

PANASONIC 24, 25, 26, 27 TOSHIBA

SANYO

01, 05

50, 51, 52, 53 SCHNEIDER 02, 15, 36

Buttons

TV/DBS

CATV/DBS CONTROL

VCR 1

Indications

DBS

VCR 1

DVD

37, 38, 77

TELEFUNKEN 40, 41, 42, 69

THOMSON

71, 72

37, 43, 44

45, 46

DVD or DVD MULTI

ZENITH

PHILIPS

15, 17, 28, 75

Manufacturers’ codes are subject to change without notice. If they

are changed, this remote control cannot operate the equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

For CATV converter

Manufacturer Codes

To cha nge t he t r a ns m it t a ble s igna ls for

oper a t ing a CATV conver t er or DBS t uner

GENERAL INSTRUMENT 06, 07, 08, 09, 10, 11,

12, 13, 14, 29

1. Press and hold CATV/DBS POWER.

2. Press CATV/DBS CONTROL.

HAMLIN/REGAL

JERROLD

01, 02, 03, 04, 05

06, 07, 08, 09, 10, 11,

12, 13, 14

15, 16, 17

18, 19, 20

21, 22

3 Enter manufacturer’s code using buttons 1–9,

and 0.

OAK

See the following lists to find the code.

PANASONIC

PIONEER

4. Release CATV/DBS POWER.

The following buttons can be used for the CATV converter and

DBS tuner:

SCIENTIFIC ATLANTA

TOCOM

23, 24, 25

ZENITH

27, 28

CATV/DBS POWER:

Turns on and off the CATV converter

or DBS tuner.

Changes the channels.

Manufacturers’ codes are subject to change without notice. If

they are changed, this remote control cannot operate the

equipment.

CH +/–:

1 – 10, 0, 100+ (+10): Selects the channels.

The 10 button will function as the

ENTER button if your equipment

requires pressing ENTER after

selecting a channel number.

To cha nge t he t r a ns m it t a ble s igna ls for

oper a t ing a not her m a nufa ct ur er ’s VCR

Note:

Refer to the manual supplied with your CATV converter or DBS

tuner.

1. Press and hold VCR 1 POWER.

2. Press VCR 1.

5. Try to operate your CATV converter or DBS

3. Enter manufacturer’s code using buttons 1–9,

and 0.

tuner by pressing CATV/DBS POWER.

When your CATV converter or DBS tuner turns on or off, you

have entered the correct code.

See the list on the next page to find the code.

If there are more than one code listed for your brand of

CATV converter or DBS tuner, try each one until the correct

one is entered.

4. Release VCR 1 POWER.

The following button can be used for operating the VCR:

VCR 1 POWER:

Turns on and off the VCR.

Note:

After pressing VCR 1, you can perform the following operations

on the VCR:

You cannot use both of the CATV converter and DBS tuner at the

same time.

CH +/–:

Changes the TV channels on the

VCR.

For DBS tuner

Manufacturer

Codes

56, 57, 67

1 – 10, 0, 100+ (+10): Selects the TV channels.

The 10 button will function as the

JVC

ENTER button if your VCR requires

pressing ENTER after selecting a

channel number.

AMSTRAD

BLAUPUNKT

ECHOSTAR

GOLDSTAR

GRUNDIG

HIRSHMANN

INSTRUMENT

ITT/NOKIA

KATHREIN

NEC

43, 44, 45, 46, 47, 48, 49

50, 51, 67

32, 33

48, 52, 53, 54, 55

52, 58, 59, 60, 61, 62, 63

35, 36

37, 38

3 PLAY:

REW:

FF:

7 STOP:

8 PAUSE:

REC PAUSE:

Starts playback.

Rewinds a video tape.

Fast winds a video tape.

Stops operation.

Pauses.

Enters recording pause.

Note:

ORBITECH

PHILIPS

RCA

Refer to the manual supplied with your VCR.

SAMSUNG

SCHWAIGER

SIEMENS

SONY

39, 40

61, 64

41, 42

5. Try to operate your VCR by pressing VCR 1

POWER.

When your VCR turns on or off, you have entered the correct

code.

If there are more than one code listed for your brand of

VCR, try each one until the correct one is entered.

TECHNISAT

Manufacturers’ codes are subject to change without notice. If

they are changed, this remote control cannot operate the

equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manufacturer

JVC

AIWA

BELL & HOWELL

BLAUPUNKT

CGM

EMERSON

FISHER

Codes

After pressing DVD, these buttons

can be used for the DVD menu

operations.

ROOM

SIZE

EFFECT

00, 26, 27, 28, 29, 58

LIVENESS

01, 02

04, 05

06, 07

TEST

CTR TONE

Note:

ENTER

∗L/R BAL

For detailed menu operations, refer to

the instructions supplied with the discs

or the DVD player.

08, 10, 11, 12, 64, 65

03, 14, 15, 16, 17

FUNAI

18, 19, 20

13, 21

06, 22

Note:

GOLDSTAR

GOODMANS

GRUNDIG

HITACHI

Refer to the manual supplied with your DVD player.

5. Try to operate your DVD player by pressing one

18, 23, 24, 25, 66

of the above buttons.

LOEWE

07, 21

04, 19, 24

30, 31, 32, 33, 34, 35

26, 27

MAGNAVOX

MITSUBISHI

NEC

• DO NOT forget to turn on the DVD player before pressing

one of the above buttons.

If there are more than one code listed for your brand of

DVD, try each one until the correct one is entered.

NOKIA

03, 36

NORDMENDE

ORION

PANASONIC

PHILIPS

PHONOLA

RCA/PROSCAN

SABA

19, 24, 39, 40

04, 19, 21, 24, 41, 42

04, 18, 19, 23, 24, 43, 44, 45

38, 46

Manufacturer

Codes

JVC

00, 02

DENON

PANASONIC

PHILIPS

PIONEER

RCA

SAMSUNG

SANYO

SHARP

SIEMENS

SONY

TELEFUNKEN

TOSHIBA

ZENITH

45, 47, 59, 61, 62, 63

03, 48, 49

37, 50

03, 51

52, 53, 54

55, 60

04, 05, 06

SAMSUNG

SONY

43, 44

56, 57

TOSHIBA

YAMAHA

11, 12

Manufacturers’ codes are subject to change without notice.

If they are changed, this remote control cannot operate the

equipment.

Manufacturers’ codes are subject to change without notice.

If they are changed, this remote control cannot operate the

equipment.

To cha nge t he t r a ns m it t a ble s igna ls for

oper a t ing a DVD pla yer

1. Press and hold AUDIO POWER.

2 Press DVD.

3. Enter manufacturer’s code using buttons 1–9,

and 0.

See the following list to find the code.

4. Release AUDIO POWER.

After pressing DVD or DVD MULTI, you can perform the

following operations on a DVD player:

3 PLAY:

Starts playing.

Returns to the beginning of the

current (or previous) track.

Skips to the beginning of the next

track.

¢:

7 STOP:

8 PAUSE:

Stops playing.

Stops playing temporarily. To release

it, press 3 PLAY.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tr oubles hoot ing

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your J VC

service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet. (See

page 10.)

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

necessary. (See pages 4 and 5.)

The SPEAKERS ON/OFF 1 and

SPEAKERS ON/OFF 2 buttons are not

set correctly.

Press SPEAKERS ON/OFF 1 and

SPEAKERS ON/OFF 2 correctly. (See page

13.)

An incorrect source is selected.

Muting is activated.

Select the correct source.

Press MUTING to cancel the mute. (See

page 13.)

An incorrect input mode (analog or

digital) is selected.

Select the correct input mode (analog or

digital). (See page 20.)

Connections are incorrect.

Check connections.

For analog connections, see page 5.

For digital connections, see page 8.

For USB connection, see page 9.

Speaker signal cables are not connected

properly.

Check speaker wiring and reconnect if

necessary. (See pages 4 and 5.)

Sound from one speaker only.

The balance is set to one extreme.

Adjust the balance properly. (See page 16.)

USB device is not selected on the

computer.

Select “USB Audio Device [1]” for

“Playback” of “Audio” (see page 9).

Refer to the manuals supplied with your PC.

No sound from PC connected with a USB

cable.

“Mute” is selected on the PC.

Check if the volume is set at low level.

Refer to the manuals supplied with your PC.

Strong electromagnetic wave is emitted

from such as television.

Move the PC away from the device such as

TV emitting strong electromagnetic wave.

Noise while reproducing PC sound

connected with a USB cable.

PC is subjected to excessive load due to

using other applications.

Close the applications you do not use.

Sound from PC connected with a USB

cable is intermittent.

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

your dealer. (See page 3.)

Continuous hiss or buzzing during FM

reception.

The station is too far away.

An incorrect antenna is used.

Select a new station.

Check with your dealer to be sure you have

the correct antenna.

Antennas are not connected properly.

Ignition noise from automobiles.

Check connections. (See page 3.)

Move the antenna farther from automobile

traffic.

Occasional cracking noise during FM

reception.

An earth (H) cable is not connected to the

AM (H) terminal on the rear panel.

Connect the cable to the AM (H) terminal

Noise is heard

on the rear panel.

The line direct function is turned on.

Turn off the line direct function. (See page

14.)

No sound effect such as DSP mode and

digital equalization.

Your turntable is too close to the

speakers.

Move the speakers away from the turntable.

Howling during record playing.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

POSSIBLE CAUSE

SOLUTION

“OVERLOAD” starts flashing on the

display.

Speakers are overloaded because of high

volume.

1. Press POWER on the front panel to turn off

the receiver.

2. Stop the playback source.

3. Turn on the receiver again, and adjust the

volume.

Speakers are overloaded because of short

circuit of speaker terminals.

Press POWER on the front panel, then check

the speaker wiring.

If “OVERLOAD” does not disappear, unplug

the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact

your dealer.

The STANDBY lamp lights up after

turning on the power, but soon the

receiver turns off again (into standby

mode).

The receiver is overloaded because of a

high voltage.

Press POWER on the front panel to turn off

the receiver. After unplugging the AC power

cord, consult your dealer.

Remote control does not work.

There is an obstruction in front of the

remote sensor on the receiver.

Remove the obstruction.

Batteries are weak.

Replace batteries. (See page 10.)

An incorrect remote control operation

mode is selected.

Select the correct remote control operation

mode. (See page 52.)

Remote control does not work intendedly.

Download from Www.Somanuals.com. All Manuals Search And Download.

S pecifica t ions

Am plifier

Output Power:

At Stereo operation:

Front channels:

120 W per channel, min. RMS, driven into 8 Ω, 20

Hz to 20 kHz with no more than 0.08% total

harmonic distortion.

At Surround operation:

Front channels:

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no

more than 0.8% total harmonic distortion.

Center channel:

Rear channels:

100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than

0.8% total harmonic distortion.

100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no

more than 0.8% total harmonic distortion.

Audio

Audio Input Sensitivity/Impedance (1 kHz):

PHONO (MM):

2.5 mV/47 kΩ

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

200 mV/47 kΩ

Audio Input (DIGITAL IN)* :

Coaxial: DIGITAL 1 (DVD):

Optical: DIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR):

–21 dBm to –15 dBm (660 nm ±30 nm)

0.5 V(p-p)/75 Ω

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with

sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).

USB:

Revision 1.0, full-speed (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz)

Audio Output Level:

Digital output:

VCR 1, VCR 2, CDR, TAPE/MD:

Optical: DIGITAL OUTPUT:

200 mV

Signal wave length: 660 nm

Output level: –21 dBm to –15 dBm

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

PHONO (MM):

70 dB/78 dB (at REC OUT)

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

92 dB/80 dB (LINE DIRECT ON)

Frequency Response (8 Ω):

PHONO:

20 Hz to 20 kHz (±1 dB)

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS, CD, CDR, TAPE/MD:

20 Hz to 100 kHz (+1 dB, –3 dB)

USB:

20 Hz to 20 kHz (+1 dB, –3 dB)

RIAA Phono Equalization:

Bass boost:

±1.0 dB (20 Hz to 20 kHz)

+6 dB ±1.0 dB at 100 Hz

Video

Video Input Sensitivity/Impedance:

Composite video:

DVD, VCR 1, VCR 2, VIDEO, TV SOUND/DBS:

1 V(p-p)/75 Ω

S-video:

(Y: luminance):

(C: chrominance, burst): 0.286 V(p-p)/75 Ω

(Y: luminance):

(P^B, PR):

Component video:

DVD, DBS:

1 V(p-p)/75 Ω

0.7 V(p-p)/75 Ω

Video Output Level:

Composite video:

S-video:

VCR 1, VCR 2, MONITOR OUT:

1 V(p-p)/75 Ω

(Y: luminance):

(C: chrominance, burst): 0.286 V(p-p)/75 Ω

(Y: luminance):

(P^B, PR):

Component video:

MONITOR OUT:

1 V(p-p)/75 Ω

0.7 V(p-p)/75 Ω

Synchronization:

Signal-to-Noise Ratio:

On-Screen Color System:

Negative

45 dB

NTSC

Download from Www.Somanuals.com. All Manuals Search And Download.

FM t uner (IHF)

Tuning Range:

Usable Sensitivity:

87.5 MHz to 108.0 MHz

Monaural:

12.8 dBf (1.2 µV/75 Ω)

21.3 dBf (3.2 µV/75 Ω)

41.3 dBf (31.5 µV/75 Ω)

50 dB Quieting Sensitivity:

Monaural:

Stereo:

Signal-to-Noise Ratio (IHF-A weighted):

Total Harmonic Distortion:

Monaural:

Stereo:

78 dB at 85 dBf

73 dB at 85 dBf

Monaural:

Stereo:

0.4% at 1 kHz

0.6% at 1 kHz

Stereo Separation at REC OUT:

Alternate Channel Selectivity:

Frequency Response:

35 dB at 1 kHz

45 dB: (±400 kHz)

30 Hz to 15 kHz: (+0.5 dB, –3 dB)

AM t uner

Tuning Range:

Usable Sensitivity:

530 kHz to 1 710 kHz

Loop antenna

400 µV/m

Signal-to-Noise Ratio:

50 dB (100 mV/m)

Gener a l

Power Requirements:

Power Consumption:

AC 120V , 60 Hz

320 W/440 VA (at operation)

2 W (in standby mode)

Dimensions (W x H x D):

Mass:

435 mm x 156.5 mm x 425 mm

(17 ³/16 in. x 6 ³/16 in. x 16 ³/4 in.)

11.5 kg (25.4 lbs)

Designs & specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

QUALITY

SERVICE

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE : 1-800-537-5722

http://www.jvcservice.com

Dear customer:

In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair

is necessary, or for the address nearest your location, please refer to the factory service center list below or within the Continental

United States, Call 1-800-537-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.

—JVC

JVC SERVICE & ENGINEERING

COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

FACTORY SERVICE CENTER LOCATIONS

10 New Maple Avenue

Pine Brook, NJ 07058-9641

(973) 396-1000

1500 Lakes Parkway

Lawrenceville, GA 30243-5857

(770) 339-2582

705 Enterprise Street

Aurora, IL 60504-8149

(630) 851-7855

5665 Corporate Avenue

Cypress, CA 90630-0024

(714) 229-8011

2969 Mapunapuna Place

Honolulu, HI 96819-2040

(808) 833-5828

10700 Hammerly, Suite 110

Houston, TX 77043

(713) 935-9331

13 Cummings Park

Woburn, MA 01801

(781) 376-9100

8192 State Road 84

Davie, FL 33324

(954) 472-1960

890 Dubuque Avenue

South San Francisco, CA 94080-1804

(650) 871-2666

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of

the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The

JVC service and engineering organization stands behind our products.

NATIONAL HEADQUARTERS

JVC SERVICE & ENGINEERING COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

1700 Valley Road

Wayne, NJ 07470

If you ship the product • • •

Don’t service it yourself.

Pack your JVC unit in the original carton or one of equivalent

size and strength. Enclose, with the unit, a letter stating the

problem or symptom that exists and also a copy of the

CAUTION

receiptorbillofsaleyoureceivedwhenyoupurchasedyour

JVC unit. Print your home return address on the outside

and the inside of the carton. Send to the appropriate JVC

Factory Service Center as listed above.

To prevent electrical shock, do not open the cabinet. No user

serviceable parts inside.

Refer servicing to qualified service personnel.

ACCESSORIES

To purchase accessories for your JVC product, you may contact your local JVC Dealer.

Or from the 48 Continental United States call toll free : 800-882-2345

(1099)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY AUDIO-2

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL

PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of original retail

purchase for the period as shown below. (“The Warranty Period.”)

PARTS

LABOR

2YR

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY(50) UNITED STATES, THE DISTRICT OF COLUMBIAAND IN

COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such

repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers.

Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be

brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and

above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized

service center, please call toll free: (800)537-5722.

If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of

your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location

of which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty

installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to

render such service, or if affixed to any attachment not provided with the products, or if the model number or serial number

has been altered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;

3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;

4. Damage that occurs in shipment, due to act of God, and cosmetic damage;

5. Signal reception problems and failures due to line power surge;

6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus(Needle) are covered for 90 days from the date of purchase;

7. Accessories;

8. Batteries (except the Rechargeable Batteries are covered for 90 days from the date of purchase);

There are no express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS

LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER

DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO

TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF

THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied

warranty last, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you

may also have other rights which vary from state to state.

JVC COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

1700 Valley Road

Wayne, NJ 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF

REFURBISHED PRO DUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION

PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this

information for future reference.

Model No.:

Serial No.:

Purchase date:

Name of dealer:

Download from Www.Somanuals.com. All Manuals Search And Download.

VICTOR COMPANY OF JAPAN, LIMITED

0101NHMMDWJEIN

Download from Www.Somanuals.com. All Manuals Search And Download.

Interlink electronic Computer Accessories 94 01441 User Manual
Jackson Thermostat 07610 003 13 91 A User Manual
Jacuzzi Hot Tub HE97000 User Manual
JVC Car Stereo System GET0576 002B User Manual
JVC CD Player UX MD9000R User Manual
JVC DVD Player SP THA25 User Manual
JVC Flat Panel Television HD 55G456 User Manual
Kenwood Satellite TV System 347 User Manual
KitchenAid Mixer KSM7990 User Manual
Knoll Stereo Amplifier MA250 User Manual