JVC MP3 Player RV NB10B User Manual

POWERED WOOFER CD SYSTEM

RV-NB10B/RV-NB10W

For Customer Use:

Enter below the Model No. and Serial No.

which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

INSTRUCTIONS

Model No.

Serial No.

LVT1539-001A

[J]

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user

serviceable parts inside the unit; leave all servicing to qualiﬁed

service personnel.

CAUTION:

•

Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper or

cloth, etc., the heat may not be able to get out.

Do not place any naked ﬂame sources, such as lighted

candles, on the apparatus.

When discarding batteries, environmental problems must be

considered and local rules or laws governing the disposal of

these batteries must be followed strictly.

•

3. CAUTION:Visible and/or invisible class 1M laser radiation when

open. Do not view directry with optical instruments.

•

Do not expose this apparatus to rain, moisture, dripping or

splashing and that no objects ﬁlled with liquids, such as vases,

shall be placed on the apparatus.

IMPORTANT POUR PRODUITS LASER

1. PRODUIT LASER CLASSE 1

2. ATTENTION: N’ouvrez pas le couvercle supérieur. Il n’y a

aucune pièce réparable par l’utilisateur à l’intérieur de l’appareil;

conﬁez toute réparation à un personnel qualiﬁé.

3. ATTENTION: Rayonnement laser visible et/ou invisible de

classe 1M une fois ouvert. Ne pas regarder directement avec des

instruments optiques.

ATTENTION:

•

Ne bloquez pas les oriﬁces ou les trous de ventilation. (Si les

oriﬁces ou les trous de ventilation sont bloqués par un journal

un tissu, etc., la chaleur peut ne pas être évacuée

correctement de l’appareil.)

•

Ne placez aucune source de ﬂamme nue, telle qu’une bougie,

sur l’appareil.

Lors de la mise au rebut des piles, veuillez prendre en

considération les problèmes de l’environnement et suivre

strictement les règles et les lois locales sur la mise au rebut

des piles.

•

N’exposez pas cet appareil à la pluie, à l’humidité, à un

égouttement ou à des éclaboussures et ne placez pas des

objets remplis de liquide, tels qu’un vase, sur l’appareil.

[European Union Only]

[Union européenne seulement]

G-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for purchasing the JVC Powered Woofer CD System.

Before operating this system, read this manual carefully and thoroughly to obtain the best possible performance from your system, and retain

this manual for future reference.

Features

Here are some of the things that make your system both powerful and simple to use.

■ General

• With JVC’s COMPU PLAY you can turn on the system and automatically start the radio, disc player, or cassette deck

with a single touch. (Only when AC power is used.)

• With the supplied wireless transmitter, you can listen to auxiliary equipment such as a digital audio player (not

supplied) by wireless connection.

• Shoulder strap with carrying cases for the remote control and auxiliary equipment, and carrying handle

• ACS (Active Clear Sound) circuit for enhancing sound reproduction

• Super woofer volume control that provides powerful bass

• Sound mode control—reproducing various sound ﬁelds

• Remote control unit that operates the disc, cassette, tuner, and wireless functions

• Locking mechanism for disc and cassette door

• Microphone/guitar input

■ Disc playback mode includes Skip Play, Search Play, Repeat Play, Random Play, and Program Play.

■ Cassette player having full logic cassette mechanism, auto reverse, and auto tape mechanism.

■ A 45-station preset capability (30 stations in FM band and 15 stations in AM band) in addition to auto-seek and manual tuning.

■ Clock/timer functions, timer on/off with preset volume function, and sleep timer.

IMPORTANT CAUTIONS

1.Where to place the system

■

• Select a place which is level, dry and neither too hot nor too cold (between 5˚C and 35˚C or 41˚F and 95˚F).

• Leave sufﬁcient distance between the system and a TV.

• Do not use the system in a place subject to vibrations.

2.Power cord

■

• Do not handle the power cord with wet hands!

• Some power is always consumed as long as the power cord is connected to the wall outlet.

• When unplugging the system from the wall outlet, always pull the plug, not the power cord.

3.When carrying the system

■

• Remove a disc from the system.

• Disconnect all the cords from the system.

4.Malfunctions, etc.

■

• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.

• Do not insert any foreign object into the system.

• The system is not waterproof or dust proof.

Table of contents

■■

Features............................................................................ 1

IMPORTANT CAUTIONS.............................................. 1

Index of parts and controls.................................. 2

Getting started....................................................... 3

Basic operations ................................................... 7

Listening to the radio............................................ 9

Playing back discs ................................................ 10

Playing back tapes................................................ 13

Recording .............................................................. 14

Listening to auxiliary equipment......................... 16

Transmitting sound on FM wave....................................16

Connecting to the AUX IN jack......................................17

Using the microphone/guitar ............................... 18

Using the timer...................................................... 18

Care and maintenance.......................................... 20

Troubleshooting .................................................... 21

Speciﬁcations........................................................ 22

Download from Www.Somanuals.com. All Manuals Search And Download.

Index of parts and controls

■■

Display window

ON/

STANDBY

FM/AM

AUX SOUND

TAPE

WIRELESS

PRESET ONE TOUCH

ACTIVE

MULTI CONTROL

STOP

TUNING

REC

CLEAR SOUND

ACS

ON LEVELSTANDBY

BEAT CUT

REW

See pages in parentheses for details.

Display window

o REC indicator (19)

; Timer indicators (19)

ON/STANDBY button (7)

2 Shoulder strap hooks (4)

3 AUX button (3, 17)

• Pressing this button also turns on the unit.

4 SOUND button (8)

•

(timer), ON, OFF

a SLEEP indicator (19)

s CLOCK indicator (8, 18)

(reverse mode) indicator (13 – 15)

5 SUPER WOOFER VOLUME +/– control knob (8)

6 LOCK/RELEASE knob (for disc) (10)

7 Disc compartment door (10)

8 VOLUME +/– control knob (7)

9 PRESET TUNING/BEAT CUT button (9, 15 – 17)

p ONE TOUCH REC button (15)

q ACTIVE CLEAR SOUND button (8)

w ACS (Active Clear Sound) indicators (8)

• ON, LEVEL

f 2 (reverse) tape direction indicator (13 – 15)

indicator (15)

h 3 (forward) tape direction indicator (13 – 15)

j MONO indicator (9, 17)

k MP3 indicator (11)

l Repeat indicators (12)

•

, ALL, GROUP

/ Main display

z PRGM (program) indicator (12)

x RANDOM indicator (12)

c Frequency unit indicators (8 – 9)

• kHz, MHz

e LOCK/RELEASE knob (for deck) (13)

r Cassette holder (13)

t STANDBY indicator (7)

y Remote sensor (4)

u MULTI CONTROL buttons (9 – 15)

• 4 REW (rewind), 7 STOP, ¢ FF (fast-forward)

i Source and play mode buttons (3, 9 – 17)

• CD 6, TAPE 2 3, WIRELESS/FM/AM

Pressing one of these buttons also turns on the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

See pages in parentheses for details.

1 Number buttons (9, 11, 17)

2 SLEEP button (19)

3 Multi control buttons (9 – 15, 18 – 19)

•

GROUP UP,

GROUP DOWN

• 4, 7, ¢

4 Source buttons (3, 9 – 17)

• AUX, CD 6, TAPE 2 3, WIRELESS/FM/AM

Pressing one of these buttons also turns on the unit.

5 PLAY MODE button (12)

6 REPEAT button (12)

7 SOUND button (8)

8 ACS (Active Clear Sound) button (8)

ON/STANDBY button (7, 18 – 20)

p DISPLAY button (8)

q CANCEL button (12, 18 – 20)

w SET button (10, 18 – 20)

e CLOCK/TIMER button (18 – 20)

r FM MODE button (9, 17)

t REVERSE MODE button (13)

y VOLUME +/– button (7)

u SUPER WOOFER VOLUME +/– buttons (8)

COMPU PLAY — One Touch Operation

With One Touch Operation you can play a disc, a tape, or turn on the radio with a single press of the play button for that function. The system

turns on and starts playing the source if it is ready.

The COMPU PLAY buttons are: On the system and remote control

CD 6 button

TAPE 2 3 button

WIRELESS/FM/AM button

AUX button

Note:The COMPU PLAY feature is not effective when the system is operated on batteries or car battery (DC12V).

Getting started

■■

Accessories

Check that you have all the following items, which are supplied with the system.

Power cord (1)

Remote control (1)

Shoulder strap with carrying cases for the remote control and auxiliary equipment (1)

Wireless transmitter (1)

Batteries*—R6(SUM-3)/AA(15F) (4)

*Supplied batteries are for the initial setup for the remote control and wireless transmitter.

If any of these items are missing, contact your dealer immediately.

Download from Www.Somanuals.com. All Manuals Search And Download.

Carrying the system

■ Using the carrying handles

Be sure to hold both handles when you carry the system.

If you carry the system by only one handle, because of the length

of the system, the end may drag on the ground and be damaged as a

result.

■ Using the shoulder strap

Attach the supplied shoulder strap (adjustable in length) to each

end of the system as illustrated.

Digital audio player etc. (not supplied)

Do not lift the system by the woofer ducts, and do not insert any

foreign objects into them.

Shoulder strap

Carrying handle

Woofer duct

Wireless

transmitter

Auxiliary

equipment case

Remote control case

Remote control

To detach the shoulder strap, press in the metal ﬁtting and unhook

it from the shaft.

Using the remote control — RM-SRVNB10J

CAUTION:

To avoid battery leakage or explosion:

■ Installing the batteries

• Remove batteries when the remote control is not in use for an

extended period of time.

• When you need to replace the batteries, replace both batteries at

the same time with new ones.

• Do not use different types of batteries together.

Point the remote control at the remote sensor on the system’s

control panel (from a distance of up to 7 m or 23 feet). If you point

the remote control from the slant direction, the distance will be

shortened.

• Do not expose the remote sensor to strong direct sunlight or

artiﬁcial lighting.

Match the polarity (+ and –) on the batteries with the +

and – markings in the battery compartment.

• Make sure there are no obstacles between the remote sensor and

the remote control.

Remote sensor

R6(SUM-3)/AA(15F) (supplied)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

CAUTION: Make all connection before plugging the system into an AC power outlet.

■ Wireless connection (See page 16.)

■ Connecting the auxiliary equipment

(See page 17.)

Wirelesstransmitter

(supplied)

Auxiliary equipment

(not supplied)

Pin-plug x 2

Signal cord (not supplied)

Stereo mini plug

Headphones jack

Auxiliary equipment

(not supplied)

■ Connecting the microphone/guitar

(See page 18.)

(not supplied)

■ Connecting to the car battery

■ Memory backup batteries

Car adapter JVC model

CA-R120 (not supplied)

To car’s cigarette

lighter socket (DC12V)

Battery cover

CAUTION:

• Be sure to use the speciﬁed car adapter (JVC model CA-R120) to prevent

mishaps or damage resulting from different polarity design.

• For safety, stop the car before performing operations.

• Be sure to start the engine when you use the car adapter; otherwise, the car

battery will be exhausted.

Match the polarity (+ and –) on the batteries

with the + and – markings in the battery

compartment.

• During transport, stabilize the system in a box, etc.

• To prevent malfunctions, do not leave the system in a car for a long time.

• If the power is supplied through the car battery, the display will be blank

with the system turned off (at standby).

Unplug the AC power cord from the system to supply the power

through the car battery; otherwise, the system does not work.

“R6(SUM-3)/AA(15F)”

size batteries (not

supplied)

■ Connecting the AC power cord

Power cord

CAUTIONS:

•ONLY USE THE JVC POWER CORD PROVIDED WITH

THIS SYSTEM TO AVOID MALFUNCTION OR

DAMAGE TO THE SYSTEM.

•BE SURE TO UNPLUG THE POWER CORD FROM THE

OUTLET WHEN GOING OUT OR WHEN THE SYSTEM

IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

Download from Www.Somanuals.com. All Manuals Search And Download.

PHONES jack

To remove the batteries, remove battery

“10” ﬁrst.

To remove the batteries, remove battery

“3” ﬁrst.

■ Operating the system on

batteries

Notes:

• When you operate the system on mains

(AC) power or on car battery (DC12V), the

power source automatically switches from

batteries to AC or DC12V. However, you

should remove the 10 batteries when

operating on AC power or car battery

(DC12V).

• When the batteries are exhausted, the

following symptoms will occur:

–Mistracking occurs during disc playback.

–Sounds are distorted intermittently during

tape playback.

–“DC OFF” ﬂashes on the display, then the

power goes off.

If this happens, replace the batteries.

• It is recommended to use AC power cord

when recording important material or

listening to a disc.

• The memory backup batteries will not be

consumed as long as the power is supplied

from an AC outlet, loaded 10 batteries, or

car battery (DC12V). However, if no power

is supplied to the system, the memory

backup batteries should be replaced with

new ones approximately every 12 months to

securely maintain the contents of the

memory.

• Before replacing the memory backup

batteries, always connect theAC power cord

to the system to prevent the contents of

memory from being erased.

Battery cover

Match the polarity (+ and –) on the batteries

with the + and – markings in the battery

compartment.

• When a power failure occurs, the time

indication disappears from the display to

save the battery power of the memory

backup batteries.

CAUTION:

To avoid battery leakage or explosion:

• When you need to replace the batteries,

replace all batteries at the same time with

new ones. Before replacing, you need to

supply AC power to the system.

• Do not use an old battery with new ones.

• Do not use different types of batteries

together.

To avoid battery leakage or explosion:

• Remove the 10 batteries when the system is

not in use for an extended period of time.

• When you need to replace the batteries,

replace all batteries at the same time with

new ones.

“R20/D(13F)” size

batteries (not supplied)

• Do not use different types of batteries

together.

• If the power is supplied through the

batteries, the display will be blank with the

system turned off (at standby).

Unplug the AC power cord from the

system to supply the power through the

batteries; otherwise, the system does

not work.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

■■

ON/STANDBY

SUPER WOOFER

VOLUME +/–

DISPLAY

VOLUME +/–

SOUND

STANDBY

indicator

ON/STANDBY

SUPER WOOFER

VOLUME +/–

SOUND

ACS

ACTIVE CLEAR

SOUND

ACS ON/LEVEL

indicator

VOLUME +/–

Turning off the system

Turning the power on and off

Press

ON/STANDBY again.

Note: The lighting condition for the STANDBY indicator and the

The STANDBY indicator lights up when the system is operated on

AC power.

• When the AC power is used, the CLOCK indicator and the time

are displayed without backlighting.

display differs depending on the power source.

Power source

STANDBY indicator/display

• The STANDBY indicator lights when

power is turned off.

• Backlighting of the display is illuminated

when power is turned on.

AC power

• The STANDBY indicator does not light.

• Backlighting of the display is not

illuminated.

• With the system turned off (at standby), no

indication is shown on the display.

Batteries or car

battery (DC12V)*

On remote control

On system

■ Some power is always consumed even though power is turned

off (called standby mode).

■ To disconnect the system from mains (AC) supply completely,

unplug the AC power cord from the AC outlet. When you

unplug the AC power cord, the clock will be reset to “AM12:00”

if no memory backup batteries are installed.

* If no source is playing and no operation is done for about 4

minutes, “DC OFF” starts ﬂashing on the display for about one

minute before the system turns off automatically (except when

the source is WIRELESS/FM/AM or AUX, or when the

microphone (or guitar) is used).

Adjusting the volume

You can adjust the volume level between 0 and 50.

Turning on the system

Press

ON/STANDBY.

Using the system

• When the system is operated on batteries or car battery (DC12V),

Turn the VOLUME +/– control clockwise to

increase the volume or turn it

press ON/STANDBY on the system.

The STANDBY indicator goes out when the system is operated on

AC power.

counterclockwise to decrease the volume.

The display comes on and the system is ready to continue in the

mode it was in when the power was last turned off.

Using the remote control

Press VOLUME + to increase the volume or

press VOLUME – to decrease it.

When you press and hold VOLUME + or –, the volume changes

rapidly.

On system

On remote control

CAUTION: DO NOT start playing any source

without ﬁrst setting the volume to minimum, as a

sudden blast of sound can damage your hearing,

speakers and/or headphones.

For private listening

Connect a pair of headphones to the PHONES jack on the rear of

the system (see page 6). No sound comes out of the speakers.

Be sure to turn down the volume before connecting or putting on

headphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the super woofer

volume

Selecting the sound mode

Sound modes can be selected to enhance the type of music being

played.

During play, you can adjust the bass level between BASS 1

(minimum) and BASS 6 (maximum).

Press SOUND to select the sound mode.

Each time you press the button, the sound mode changes as

follows:

Using the system

Turn the SUPER WOOFER VOLUME +/–

control clockwise to increase the bass level

or turn it counterclockwise to decrease the

bass level.

On remote control

On system

Sound mode selection:

Using the remote control

Press SUPER WOOFER VOLUME + to

increase the bass level or press SUPER

WOOFER VOLUME – to decrease it.

BEAT: Set to this position for music with a heavy beat, such as

rock and disco music.

POP: Set to this position for light music including popular and

vocal music.

CLEAR: Set to this position for crisp and clear sounding music

with transparent highs.

FLAT (no effect): Set to this position not to apply any sound

mode.

Showing the time

While the power is turned on, you can see the current time (clock)

at any time, as follows.

Note: This function is not effective when the headphones are in

use.

Activating clear sound

Using the remote control only

Press DISPLAY.

Each time you press the button, the display changes as follows:

The Active Clear Sound (ACS) circuit emphasizes high-frequency

sound without lowering the signal-noise ratio, while adjusting its

output according to the input signal level. This results in a better

balance between the high-frequency sound and the low-frequency

heavy bass.

Press ACS (active clear sound) on the

system or on the remote control to turn it on

or off.

Current sound source (e.g. FM103.5 MHz) = (clock) = (back to

the beginning)

When it is turned on, the ACS ON indicator lights in red.

Note: To let the clock work, you need to set the clock ﬁrst. (See

“Setting the clock” on page 18.)

On remote control

On system

• The ACS LEVEL indicator ﬂashes in green according to the input

signal level.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the radio

■■

Number buttons

SET

WIRELESS/

FM/AM

WIRELESS/FM/AM

PRESET TUNING

FM MODE

You can listen to FM and AM stations. Stations can be tuned in manually, automatically, or from preset memory storage.

■ Before listening to the radio, fully extend the FM telescopic antenna.

Tuning in to a station

■ Preset Tuning (possible only after presetting stations)

Select the desired preset number using PRESET TUNING on

the system or the number buttons on the remote control. The

preset number and then the band frequency appear on the

display.

1.Press WIRELESS/FM/AM repeatedly to

■

select either FM or AM.

Each time you press WIRELESS/FM/AM, the band changes as

follows:

WIRELESS = FM = AM = (back to the beginning)

• For “WIRELESS,” see page 17.

PRESET TUNING button: Each time you press the button, the

The system tunes in to the last tuned station. The following

information appears on the display.

–When “Manual Tuning” or “Auto Tuning” was used to tune in

to the last tuned station (see below), the band frequency

appears.

preset number increases.

Number buttons:

To select P-5, press 5.

To select P-15, press +10 then 5.

To select P-20, press +10 once then

press 10.

Notice: To adjust the reception condition

–When “Preset Tuning” was used to tune in to the last tuned

station (see the right column), the preset number (displayed

as “P-XX” on the display) and then the band frequency

appear.

For FM: Adjust the FM telescopic antenna’s length, angle and

direction until the best reception is obtained.

(After one second)

2.Select a station using one of the following

■

methods.

• If an FM stereo broadcast is hard to receive or

noisy, press FM MODE on the remote control. The MONO

indicator lights up and the sound becomes monaural, but the

reception improves. When you tune in to another station, the

MONO indicator goes off and stereo effect restores

automatically.

Note: AM broadcasts are monaural.

For AM: Change the direction of the system to obtain the best

reception.

■ Manual Tuning

Press 4 or ¢ repeatedly to move from frequency to

frequency until you ﬁnd the station you want.

Placing the system near the window, for example, will

improve AM reception.

■ Auto Tuning

Press and hold 4 or ¢ for one second or more.

The frequency changes automatically until a station frequency

is found.

Download from Www.Somanuals.com. All Manuals Search And Download.

Presetting stations

You can preset up to 30 FM stations and 15 AM stations.

4.Press the number buttons to select the

■

preset number you want.

Note: Preset numbers may have been set to factory test

frequencies prior to shipment. This is not a malfunction.

You can preset the stations you want into memory as

follows:

5.Press SET.

■

“STORED” appears on the display and the station is stored.

6.Repeat above steps

for each

■

Using the remote control only

station you want to store into memory with

a preset number.

There is a time limit in doing the following steps. If the setting is

canceled before you ﬁnish, start again from step

To change the preset stations, repeat the same steps as

above to overwrite a new station.

1.Select a band (either AM or FM) by

■

pressing WIRELESS/FM/AM repeatedly.

CAUTION: To prevent the preset stations from

being erased because of a power failure, etc.,

install memory backup batteries in the system.

(See pages 5 and 6.)

2.Press 4 or ¢ to tune in to a station.

3.Press SET.

■

Playing back discs

■■

Number buttons

CD 6

LOCK/RELEASE knob

CANCEL

GROUP UP

CD 6

GROUP DOWN

PLAY MODE

REPEAT

This system has been designed to play back the following discs—

CD, ﬁnalized CD-R/CD-RW (recorded in audio CD format) and

CD-R/CD-RW (in MP3 format).

• This system recognizes up to 999 tracks on a disc (or less

depending on the recording condition of a disc).

• This system is not compatible with the other discs such as DVD,

DVD-R, and DVD-RW.

Setting a disc

Notes on MP3:

1.Turn the LOCK/RELEASE knob

• The system can only recognize ﬁles (tracks) with “MP3” or

“mp3” as the extensions, which can be in any combination of

upper and lower case.

■

counterclockwise to open the disc

compartment door.

• It is recommended that you record your material at a 44.1 kHz

sampling rate, using the 128 kbps data transfer rate.

• You can play back the discs containing the tracks in music CD

format or MP3 ﬁles in ISO 9660 format.

• Some MP3 tracks or discs may not be played back because of

their characteristics or recording conditions.

• MP3 discs require a longer readout time than normal discs.

2.Place a disc, with its label side up as

■

shown above.

3.Close the disc compartment door and turn

■

the knob to “LOCK” position.

To remove the disc, open the disc compartment door in stop

mode.

■ You can place an 8 cm (3-3/16") disc without an adapter.

■ If the disc cannot be read correctly (because it is scratched, for

example), “NO PLAY” or “NO DISC” appears on the display.

■ You can place a disc while listening to the other source.

Group with its play order

MP3 track with its play order

Download from Www.Somanuals.com. All Manuals Search And Download.

Skip Play

Press 4 or ¢ to select the track you want

to play during playback.

Using the disc player—Normal

Play

• Press ¢ once to skip to the beginning of the next track.

• Press 4 to skip to the beginning of the track being played.

Press 4 twice quickly to skip to the beginning of the previous

track.

To play a disc

1.Set a disc.

■

2.Press CD 6.

■

You can also select a track in stop mode with the same buttons.

For CD: Selected track and its playback time are shown on the

display.

For MP3:Group and track numbers (then ID3 Tag if any) are

shown on the display.

The ﬁrst track of the disc starts playing.

For CDs:

Track

number

Playback

time

To start playback, press CD 6.

For MP3 discs:

Search Play

Press and hold 4 or ¢ to fast forward/

reverse the disc during playback.

You can quickly ﬁnd a particular passage in the track you are

listening to. During search play, you can hear the sound of approx.

one forth level.

MP3 indicator

• When playing an MP3 disc, the ﬁle name (then ID3 Tag if

any) is displayed at the beginning of each track.

• If no disc is inserted, “NO DISC” appears on the display and

the system remains in stop mode.

• The system automatically stops when the last track of the disc

has ﬁnished playing.

To locate a track directly

Using the remote control only

To stop playing the disc, press 7.

Press the number buttons to directly play a

track.

The following information for the disc is displayed.

For CDs:

• To directly play track 5, press 5.

• To directly play track 15, press +10 then 5.

• To directly play track 20, press +10 once then press 10.

Total track

number

Total playback

time

(Only for MP3 discs)

• To directly play track 109, press +100 once then press 9.

• To directly play track 125, press +100, +10, +10 then 5.

For MP3 discs:

Total group

number*

Total track

number

To select a group (for MP3 disc)

Using the remote control only

MP3 indicator

Press

GROUP UP or

GROUP DOWN to

* If a disc includes more than 99 groups, “G – –” will appear

on the display.

select the group you want to play during

playing the MP3 disc.

• Press

GROUP UP to skip to the next group.

GROUP DOWN to skip to the previous group.

To pause, press CD 6. The playback time ﬂashes on the

display.

You can also select a group in stop mode with the same buttons.

To cancel pause, press the same button again. Playback

To play the group after selection, press CD 6.

continues from the point where it was paused.

Note: Do not turn the LOCK/RELEASE knob during playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the playing order

of the tracks

Random play

The tracks will play in no special order when you use this mode.

Using the remote control only

■ You can program up to 50 tracks in any desired order including

the same tracks.

■ You can only make a program when the system is stopped.

■ While making a program, you cannot specify a group number to

select a track.

1.Set a disc.

■

2.Press CD 6.

■

3.Press 7 to stop the disc.

■

4.Press PLAY MODE repeatedly to select

1.Set a disc.

■

“RANDOM.”

The RANDOM indicator lights up on the display.

2.Press CD 6.

■

5.Press CD 6.

3.Press 7 to stop the disc.

■

The tracks are played in random order once.

4.Press PLAY MODE repeatedly to select

To skip a track during playback, press ¢ to skip to another

track in the random sequence. The 4 button works only to go

back to the beginning of the current track.

“PROGRAM.”

The system enters the programming mode and the PRGM

indicator lights up.

While stopped:

5.Press the number buttons to select the

■

track to program.

■ To exit from random mode, press PLAY MODE repeatedly

until the track number and total playback time appear on the

display.

• For detailed operations, see “To locate a track directly” on

page 11.

Each time you press the button, the play mode changes as

follows:

Example: For track 7, press 7.

Last programmed track

Program order number

Normal play = PROGRAM = RANDOM = (back to the

beginning)

(After 2 seconds)

Repeating tracks

You can repeat the tracks or individual track as many times as you

like.

Total playback time of the programmed tracks*

* Total playback time will not appear while making a

program using an MP3 disc.

Using the remote control only

Press REPEAT.

6.Repeat step

to select other tracks for

■

Each time you press the button, repeat indicator changes as

the program.

follows:

• To cancel the last track programmed, press CANCEL once.

For CDs:

7.Press CD 6.

ALL =

ALL:

= canceled = (back to the beginning)

Repeats all the tracks on the disc.

Repeats the current track.

■

The system plays the tracks in the order you have programmed

them.

•

■ You can skip to a particular program track by pressing 4 or

¢ during program play.

For MP3 discs:

While stopped:

ALL =

beginning)

GROUP =

= canceled = (back to the

■ To conﬁrm the programmed tracks, press 4 or ¢

repeatedly; the tracks making up the program will successively

be displayed in the programmed order.

•

ALL:

Repeats all the tracks on the disc.

GROUP: In normal play mode, repeats all the tracks in

a group.

• To add a track to the end of the program, simply press the

number buttons.

In program and random play modes, group

repeat cannot be selected.

■ To delete the tracks in the program, press CANCEL

repeatedly. Each time you press the button, the last track will be

erased.

•

Repeats the current track.

■ To delete the entire program, press and hold CANCEL

until “CLEAR!” appears on the display.

■ Repeat mode (except “

GROUP”) remains in effect even

when you change the play mode.

• Turning off the power will clear the program.

To exit from repeat mode, press REPEAT until the repeat

indicator on the display goes out.

■ To exit from program mode, press PLAY MODE

repeatedly until the track number and total playback time

appear on the display.

Each time you press the button, the play mode changes as

follows:

Normal play = PROGRAM = RANDOM = (back to the

beginning)

Note:

(For CDs) If the total playback time of the programmed tracks

exceeds 99 minutes 59 seconds, “– – : – –” will appear on the

display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing back tapes

■■

TAPE 2 3

REVERSE

MODE

LOCK/RELEASE

knob

With automatic tape direction, you can listen to type I or II tapes

without having to change any settings.

5.If you need to change the playback

■

direction, press TAPE 2 3.

The opposite side tape direction indicator lights up and the tape

playback direction changes.

The use of tapes longer than 120 minutes is not recommended,

since characteristic deterioration may occur and these tapes easily

jam in the pinch-rollers and the capstans.

To stop playing, press 7.

To remove the tape, stop the tape, and open the cassette

holder by turning the LOCK/RELEASE knob to the

“RELEASE” position.

Regular play

1.Turn the LOCK/RELEASE knob

■

Notes:

counterclockwise to open the cassette

holder.

• Do not turn the LOCK/RELEASE knob during playback.

• When no tape is loaded in the deck, “NO TAPE” appears on the

display.

To fast-wind/rewind a tape

Press ¢ or 4 to fast-wind/rewind the tape.

• The cassette deck automatically stops when the tape reaches its

end.

2.Put the cassette in, with the side you want

■

to listen to facing you.

Reverse mode

You can set a tape to play just one side, both sides in succession, or

both sides continuously.

Using the remote control only

Press REVERSE MODE.

Each time you press the button, reverse mode indicator changes as

follows:

= (back to the beginning)

3.Close the holder gently and turn the knob

■

•

The cassette deck automatically stops after playing

one side of the tape.

to “LOCK” position.

4.Press TAPE 2 3.

■

The cassette deck automatically stops when playback

in the reverse (2) direction is ﬁnished.

: The cassette deck continues to play both sides of the

The tape is played in the direction shown by the tape direction

indicator.

3 (Forward playback): The side of the tape facing you is

played back.

tape until the 7 button is pressed.

2 (Reverse playback): The opposite side of the tape is

played back.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

■■

CD 6

TAPE 2 3

AUX

CD 6

TAPE 2 3

WIRELESS/

FM/AM

WIRELESS/

FM/AM

AUX

REVERSE

MODE

BEAT CUT

ONE TOUCH REC

Things to know before you start

recording

Standard recording

You can record any sound source to tape.

■ It should be noted that it may be unlawful to re-record

pre-recorded tapes, records, or discs without the

consent of the owner of copyright in the sound or

video recording, broadcast or cable programme and

in any literary, dramatic, musical, or artistic work

embodied therein.

The sources are disc, tuner, auxiliary equipment, microphone, and

guitar. The microphone sound and guitar sound can be mixed with

any source.

1.Insert a blank or erasable cassette tape

■

into the cassette deck.

Be sure that the tape direction indicator and the tape insertion

direction are as follows:

■ When you want to record onto both sides of a tape, you can set

reverse mode to

. Recording automatically stops after

[Forward and reverse recording]

recording in the reverse (2) direction. Therefore, make sure that

the tape direction is forward (3) when recording with reverse

mode is on.

Tape direction indicator

Tape insertion direction

■ The recording level is automatically set correctly, so it is not

affected by the VOLUME control on the system or by adjusting

the sound effects. Thus, during recording you can adjust the

sound you are actually listening to without affecting the

recording level.

■ Two small tabs on the back of the cassette tape, one for side A

and one for side B, can be removed to prevent accidental erasure

or recording.

(Forward)

* Recording will be made on

the tape side facing you.

(Front view)

■ To record on a cassette with the tabs removed, you must cover

the holes with adhesive tape ﬁrst. However, when a type II tape

is used, only cover part of the hole as shown, since the other part

of the hole (type II detection slot) is used to detect the tape type.

(Reverse)

* Recording will be made on

the opposite side of the tape.

Type II detection

slot

(Front view)

• If the tape direction 2 (reverse) is lit, press TAPE 2 3 to change

the direction. (In this case, since the tape play starts, you need to

press 7. Then, press 4 to rewind the tape up to the end point of

the leader tape which cannot be recorded onto.)

• If the inserted tape is not fully rewound, press 4 to rewind the

tape up to the end point of the leader tape which cannot be

recorded onto.

Adhesive tape

■ Type I and type II tapes can be used for recording.

Note:

At the start and end of cassette tapes, there is leader tape which

cannot be recorded onto. Thus, before recording, wind on the

leader tape ﬁrst to ensure getting the beginning of the recording.

2.If you want to record on both sides of the

■

tape, press REVERSE MODE on the remote

control to set the cassette deck in reverse

mode.

CAUTION: If a recording you make has excessive

noise or static, the system may have been too

close to a TV which was on during the recording.

Either turn off the TV or increase the distance

between the TV and the system.

Press the button until “

” is lit.

3.Prepare the source, for example, tuning in

■

to a radio station, or turning on the

connected auxiliary equipment.

Note: For disc recording, refer to “Disc direct recording”

described on page 15.

Continued on the next page...

Download from Www.Somanuals.com. All Manuals Search And Download.

4.Press ONE TOUCH REC on the system.

6.Choose whether to have pauses between

■

tracks.

The

indicator lights up and the system starts recording.

• If nothing is done, a non-recorded pause of about four

seconds will be automatically made between tracks.

• If you do not want pauses between tracks, press CD 6

twice to enter pause mode—only possible with CDs.

• If the tab of the cassette tape is removed to protect erasure or

recording, recording does not start.

Tips: When you want to record on both sides of the tape, start

recording from the forward direction.

7.Press ONE TOUCH REC on the system.

■

To stop at any time during the recording process, press 7.

The

indicator lights up and the cassette deck starts

recording.

Recording an AM station

• When the tape reaches its end at the middle of a song in the

forward direction (3), the recording in the reverse direction

(2) will start from the beginning of that track (or previous

track). See diagram below.

on a tape

When recording an AM broadcast, beats may be produced which

are not heard when listening to the broadcast. If this happens, press

BEAT CUT to eliminate the beats.

Ex.: Case 1

[Recording direction 3 (forward)]

1.Set to AM station and start recording.

■

Tape end

2.Press BEAT CUT to eliminate the beats.

■

Each time you press the button, the display changes as follows:

B.CUT-1 = B.CUT-2 = B.CUT-3 = B.CUT-4 = (back to

the beginning)

Track 1

Track 2

Disc direct recording

Everything on the disc goes onto the tape in the order it is on the

disc, or according to the order you have set in a program.

more than 10 seconds

* The recording in reverse side (2) starts from the beginning

of track 2.

1.Insert a blank or erasable cassette tape

■

Ex.: Case 2

into the cassette deck.

[Recording direction 3 (forward)]

Be sure that the tape direction indicator and the tape insertion

direction are as follows:

Tape end

[Forward recording]

Track 1

Track 2

Tape direction indicator

Tape insertion direction

less than 10 seconds

(Forward)

* The recording in reverse side (2) starts from the beginning

of track 1.

* Recording will be made on

the tape side facing you.

• After the disc player has played the entire disc, or all the

programmed tracks, the tape automatically stops.

(Front view)

• Recording will also stop when the end of the reverse side (2)

is reached (even if the disc play is not yet over).

2.If you want to record on both sides of the

■

tape, press REVERSE MODE on the remote

control to set the system in reverse mode.

To stop at any time during the recording process, press 7.

The tape stops after four seconds.

Press the button until “

” is lit.

Note:

When making SLEEP timer settings while performing disc direct

recording, set enough time to allow the disc to ﬁnish playing;

otherwise, the power will go off before recording is completed.

3.Set a disc.

■

4.Press CD 6.

■

5.Press 7.

■

• If you want to record speciﬁc tracks only, program the tracks

ﬁrst. You can check their total playback time on the display

during programming. (See page 12.)

One Track Recording

You can record the current track being played.

1.Insert a blank or erasable cassette tape

■

into the cassette deck.

2.Play the track you wish to record.

■

3.Press ONE TOUCH REC on the system.

The disc player returns to the beginning of that track and the

track is recorded on the tape. After recording, the disc player

and the cassette deck automatically stop.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to auxiliary equipment

■■

Number buttons

WIRELESS/

FM/AM

AUX

WIRELESS/

FM/AM

PRESET TUNING

FM MODE

AUX

You can listen to auxiliary equipment with the following methods:

• Transmitting sound on FM wave

• Connecting to the AUX IN jack

Note: For operation of the auxiliary equipment, refer to its instructions.

■ Transmitting sound on FM wave

You can connect auxiliary equipment such as a digital audio player to the wireless transmitter, then transmit the sound signals on FM wave.

■ Installing the batteries to the wireless

Listening to auxiliary

transmitter

equipment

1.Connect the wireless transmitter to the

■

headphones jack of auxiliary equipment.

2.Select one of the position numbers on the

■

wireless transmitter.

• To check the assigned frequency to each the position number,

refer to the label put on the rear of the wireless transmitter.

• Make sure that no local FM station in you area uses the same

frequency.

Match the polarity (+ and –) on the batteries with the +

and – markings in the battery compartment.

3.Turn on the wireless transmitter.

■

The red lamp lights up.

R6(SUM-3)/AA(15F)

(supplied)

• To select a position number from P1 - P4, set the switch to

LOW POSITION.

• To select a position number from P5 - P8, set the switch to

HIGH POSITION.

4.Set the volume level of the system to

■

minimum.

Continued on the next page...

Download from Www.Somanuals.com. All Manuals Search And Download.

5.Press WIRELESS/FM/AM to select

■

Presetting frequencies

WIRELESS as the source.

You can preset up to eight frequencies.

The system tunes in to the last tuned frequency. The following

information appears on the display.

Using the remote control only

There is a time limit in doing the following steps. If the setting is

canceled before you ﬁnish, start again from step

1.Select WIRELESS by pressing WIRELESS/

(After one second)

■

FM/AM.

2.Press 4 or ¢ to tune in to a frequency.

3.Press SET.

■

6.Select the same position number as you

■

have selected on the wireless transmitter

in step

on page 16.

• On the remote control: Press the number button

corresponding to the position number.

• On the system: Press PRESET TUNING repeatedly to

select the position number.

7.Start playing the connected equipment,

4.Press the number buttons (1 – 8) to select

■

then adjust the volume on the equipment.

the preset number you want.

8.Adjust the volume of the system to the

5.Press SET.

■

desired listening level.

“STORED” appears on the display and the frequency is stored.

• If received sounds are noisy, press FM MODE on the

remote control. The MONO indicator lights up and the sound

becomes monaural, but the reception improves. When you

tune in to another frequency using 4 or ¢, the MONO

indicator goes off and stereo effect restores automatically.

6.Repeat above steps

for each

■

frequency you want to store into memory

with a preset number.

To change the preset frequencies, repeat the same steps

as above to overwrite a new frequency.

Notice:•To adjust the reception condition

Adjust the FM telescopic antenna’s length, angle and

direction until the best reception is obtained (see page

9).

Note:

When you listen to an auxiliary equipment connected to the

wireless transmitter after changing the preset frequency initially

memorized in the system, set the frequency back to the initial one

according to the above procedure; otherwise, you cannot receive

the signal even though you select the same position number as the

one on the transmitter.

•To avoid sound distortion

Make sure not to increase the volume of the connected

equipment too high.

Following table shows the initial settings of the position numbers

on the system.

Notes:

• If the frequency (position number) you select to receive the

signals from the wireless transmitter is used by an FM station or

is adjacent to an FM station frequency, it interferes with the

reception from the wireless transmitter. If this happens, select

another frequency (position number).

• If you are nearby the TV or FM stations which transmit strong

signals, it interferes with the reception from the wireless

transmitter. In this case, you may not be able to use the wireless

transmitter.

Initial settings of the position numbers:

Position no. Frequency Position no. Frequency

POSITN 1

POSITN 2

POSITN 3

POSITN 4

88.10 MHz

88.30 MHz

88.50 MHz

88.70 MHz

POSITN 5

POSITN 6

POSITN 7

POSITN 8

107.10 MHz

107.30 MHz

107.50 MHz

107.70 MHz

• To get good reception from the wireless transmitter:

– Make sure that there is no obstruction between the system and

the wireless transmitter.

– Straighten the connecting cord of the wireless transmitter as

much as possible.

CAUTION: To prevent the preset frequencies

from being erased because of a power failure,

etc., install memory backup batteries in the

system. (See pages 5 and 6.)

■ Connecting to the AUX IN jack

First make sure that the auxiliary equipment is properly connected to the system. (See pages 5 and 6.)

1.Set the volume level to minimum.

3.Adjust the volume to the desired listening

■

level.

2.Press AUX.

■

4.Apply sound effects, if you wish.

“AUX” appears on the display.

■

• Adjust the super woofer volume to reinforce the bass sound.

• To listen to the auxiliary equipment, start playing the auxiliary

equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the microphone/guitar

■■

5.Adjust the VOLUME +/– control and the

■

Microphone/guitar mixing

MIC/GUITAR LEVEL control, as you play the

microphone or the guitar.

Using a microphone or a guitar (not supplied), you can mix its

sound with a source sound.

CAUTION: DO NOT connect a bass guitar to the

MIC/GUITAR INPUT jack, as it may damage the

system.

1.Make sure the MIC/GUITAR LEVEL control

■

on the rear of the system is properly set.

• When using a microphone, make sure the knob is pressed in

(_).

Recording microphone or

guitar mixing on a tape

• When using a guitar, make sure the knob is released (—).

2.Set the MIC/GUITAR LEVEL control to MIN

■

by turning it fully counterclockwise.

1.Follow the above steps

–

■

3.Connect a microphone or a guitar into the

2.To record, follow the steps in “Standard

■

MIC/GUITAR INPUT jack on the rear of the

system.

recording.” (See page 14.)

Note: If “howling” occurs when using the microphone, keep the

microphone away from the speaker.

4.Start a source: disc, tape, tuner, or other

■

equipment.

Using the timer

■■

ON/STANDBY

CANCEL

SET

SLEEP

CLOCK/TIMER

The timers let you control the listening and recording functions automatically.

4.Press SET to set the hour.

■

Setting the clock

The minutes digits start ﬂashing on the display.

When the power is ﬁrst supplied, the CLOCK indicator and

“AM12:00” ﬂash on the display. Set the clock.

5.Press ¢ or 4 to select the minute.

■

• When you press and hold the button, the minute digit changes

continuously.

Note:

The clock must be correctly set for the timers to work.

• If you want to change the hour setting, press CANCEL.

Using the remote control only

6.Press SET to ﬁnish setting the clock.

■

1.Press

ON/STANDBY.

■

CAUTION: If memory backup batteries are

exhausted or not installed, and the AC power

cord is plugged in again after being

2.Press CLOCK/TIMER repeatedly until the

■

CLOCK indicator lights up.

The hour digit ﬂashes on the display.

disconnected, or power is restored after a power

failure, the CLOCK indicator will ﬂash on the

display. Set the current time (clock) again.

3.Press ¢ or 4 to select the hour.

■

• When you press and hold the button, the hour digit changes

continuously.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.Press CLOCK/TIMER again, so that the

■

Setting the sleep timer

Use the sleep timer to turn the system off after a certain number of

minutes when it is playing. By setting the sleep timer, you can fall

asleep to the music and know that your system will turn off by

itself rather than playing all night.

timer indicator ( ) and ON indicator light

up.

The hour digit of the current ON time ﬂashes on the display.

■ You can set the sleep timer only when the system is turned on.

Using the remote control only

1.Press SLEEP.

4.Set the on-time you want the system to

■

The SLEEP indicator lights up on the display.

turn on.

(1) Press ¢ or 4 to select the hour, then press SET.

(2) Press ¢ or 4 to select the minute, then press SET.

The OFF indicator lights up.

2.Set the length of time you want the source

■

to play before shutting off.

Each time you press the button, it changes the number of

minutes shown on the display in this sequence:

10 = 20 = 30 = 60 = 90 = 120 = OFF = (back to the

beginning)

• Press and hold the button to change the time rapidly.

• If you want to change the time setting, press CANCEL.

5.Set the OFF time (example: PM1:30).

■

After setting the number of minutes for the sleep timer, the

indication will stop ﬂashing and go off.

The system is now set to turn off after the number of minutes you

set.

To conﬁrm the sleep time:

When SLEEP is pressed, the remaining sleep time is displayed.

Wait until the display returns to the original display.

(1) Press ¢ or 4 to select the hour, then press SET.

(2) Press ¢ or 4 to select the minute, then press SET.

• Press and hold the button to change the time rapidly.

• If you want to change the time setting, press CANCEL.

To cancel the sleep timer:

Press SLEEP repeatedly to select “OFF.” Turning off the system

also cancels the sleep timer.

6.Press ¢ or 4 to select the music source

■

you want to listen to, then press SET.

Each time you press the button, the display changes as shown

below:

Setting the daily timer

Once the timer has been set, it will be activated at the same time

everyday until the timer is turned off. Recording timer works only

one time.

TUNER =TU\TAPE = CD =TAPE = (back to the

beginning)

When you select the “TU\TAPE”;

• The REC indicator appears on the display.

• The timer will be canceled after tuner recording has been

ﬁnished.

• While the timer is being set, the timer indicator (

• While the timer has been set, the timer indicator (

up if the power is supplied through the AC outlet.

• While the timer is working, the timer indicator (

) lights up.

) also lights

) ﬂashes.

7.Press ¢ or 4 to select the volume level,

■

then press SET.

Using the remote control only

– –:

The current volume level will be used.

0 to 50:When the timer is turned on, the volume will be

automatically set to the selected level.

1.Press

ON/STANDBY.

■

2.Press CLOCK/TIMER.

■

“TIMER ON?” appears.

• Press SET to activate the timer setting you have made before.

• Press CANCEL to cancel the timer.

• Go to the next step to set the timer ﬁrst time (or reset the

timer).

• The current timer setting appears for conﬁrmation.

Download from Www.Somanuals.com. All Manuals Search And Download.

To cancel the operation, press CLOCK/TIMER until the

display returns to the original one.

8.Before turning off the system, prepare the

■

music source selected in step

19.

on page

To cancel the timer, press CLOCK/TIMER once, then press

CANCEL. (“TIMEROFF” appears, only when power is on.)

TUNER:

Tune in to the desired frequency (FM/AM/

WIRELESS).

To reactivate (or conﬁrm) the canceled timer, press

CLOCK/TIMER once, then press SET. (The current timer setting

appears for conﬁrmation.)

TU\TAPE: Tune in to the frequency (FM/AM/

WIRELESS) you want to record. Insert a

cassette tape for recording.

CD:

TAPE:

Set a disc.

Insert a tape.

Notes:

• The timer cannot be set if on-time and off-time are the same.

• The timer does not work if the system is not in the standby mode

(the system needs to be in standby mode at least one minute

before the on-time).

Notes:

• By using “WIRELESS,” you can also record the sounds

through the auxiliary equipment connected to the wireless

transmitter.

• Listening to or recording auxiliary equipment connected to

the wireless transmitter, start playing the equipment before

the timer turns on.

CAUTION: If memory backup batteries are

exhausted or not installed, and the AC power

cord is disconnected or there is a power failure,

time settings will be erased from memory. If this

happens, set the current time (clock) and

perform the timer setting again.

9.Press

ON/STANDBY to turn off the

■

system.

• When the timer turns on, the volume level gradually increases

from 0 (zero) to the preset level in step on page 19.

However, if the volume has been set to “– –”, the volume

level will be set to the last level directly.

Care and maintenance

■■

Compact discs

Handle your discs carefully, and they will last a long time.

General notes

In general, you will have the best performance by keeping your

discs and the mechanism clean.

• This system can play back the following discs:

– Audio CD

• Store discs in their cases, and keep them in cabinets or on shelves.

• Keep the disc compartment door closed when not in use.

– Finalized CD-R/CD-RW recorded in audio

CD format or MP3 format

However, continued use of irregular shape

discs (heart-shape, octagonal, etc.) can damage

the system.

Cleaning the lens

If the lens in the pickup is dirty, dropout, etc., could degrade sound.

Open the disc compartment door and clean the lens as shown.

• Use a blower (available at camera stores) to blow dust off the

lens.

• Remove the disc from its case by holding it at

the edges while pressing the case’s center hole

lightly.

• Do not touch the shiny surface of the disc, or

bend the disc.

Blower

Lens

• Put the disc back in its case after use to prevent

warping.

• Be careful not to scratch the surface of the disc

when placing it back in the case.

• Avoid exposure to direct sunlight, temperature

extremes, and moisture.

• If there are ﬁngerprints, etc. on the lens, gently wipe clean with a

cotton swab.

• A dirty disc may not play correctly. If a disc

does become dirty, wipe it with a soft cloth in a

straight line from center to edge.

CAUTION: Do not use any solvent (for example,

conventional record cleaner, spray thinner,

benzine, etc.) to clean a disc.

Continued on the next page...

Download from Www.Somanuals.com. All Manuals Search And Download.

Moisture condensation

Cassette deck

Moisture may condense on the lens inside the

• If the heads, capstans, or pinch-rollers of the cassette deck

become dirty, the following may occur:

–Loss of sound quality

system in the following cases:

• After turning on heating in the room.

• In a damp room.

–Discontinuous sound

• If the system is brought directly from a cold to

a warm place.

–Fading

–Incomplete erasure

Should this occur, the system may malfunction.

In this case, leave the system turned on for a few

hours until the moisture evaporates, unplug the

AC power cord, and then plug it in again.

–Difﬁculty recording

• Clean the heads, capstans, and pinch-rollers using a cotton swab

moistened with alcohol.

Capstans

Pinch-rollers

Erase head

Record/play head

Cassette tapes

• If the tape is loose, it may get stretched, cut, or

caught in the cassette. Take up the slack by

inserting a pencil in one of the reels and

rotating.

• If the heads become magnetized, the system will produce noise or

lose high frequency notes.

• To demagnetize the heads, turn off the system, and use a head

demagnetizer (available at electronics and record shops).

• Do not touch the tape surface.

• Do not store the tape:

–In dusty places

–In direct sunlight or heat

–In moist areas

–On a TV or speaker

–Near a magnet

Troubleshooting

If you are having a problem with your system, check this list for a possible solution before calling for service.

If you cannot solve the problem from the hints given here, or the system has been physically damaged, call a qualiﬁed person, such as your

dealer, for service.

■■

•

Symptom

Possible cause

Action

Power does not come on.

The power cord is not connected to an AC

outlet.

Insert the plug into the socket.

No sound is heard.

• Connections are incorrect, or loose.

• Check all connections and make

corrections. (See pages 5 and 6.)

• Disconnect the headphones.

• Headphones are connected.

• MP3 disc is recorded with “packet

writing.”

• It cannot be played. Replace the disc.

Poor FM reception.

The track skips.

The FM telescopic antenna is not properly

extended and positioned.

Fully extend the FM telescopic antenna

and turn it for the best reception.

The disc is dirty or scratched.

Clean or replace the disc.

The disc does not play (“NO PLAY” or

“NO DISC” appears).

• The disc is upside down.

• The disc is dirty or scratched.

• Put the disc in with the label side up.

• Change the disc.

Speciﬁc ﬁles (tracks) on an MP3 disc are

not played.

Files other than MP3 are included in the

disc.

They cannot be played.

Hard to hear auxiliary equipment

connected to the wireless transmitter

because of noise.

• The selected position number on the

system is different from the one selected

on the wireless transmitter.

• The volume of the connected equipment

is low.

• Select the same position number as you

have selected on the wireless transmitter.

(See page 17.)

• Turn up the volume.

• The wireless transmitter is far from the

system.

• Bring the wireless transmitter close to the

system.

Unable to record.

Cassette record protect tabs are removed.

Cover the holes on the back edge of the

cassette with tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptom

Possible cause

Action

Unable to operate the remote control.

• The path between the remote control and

the sensor on the system is blocked.

• The batteries have lost their charge.

• Remove the obstruction.

• Replace the batteries.

Operations are disabled.

The built-in microprocessor has

malfunctioned due to external electrical

interference.

Unplug the system then plug it back in

after a few minutes.

The cassette holder cannot be opened.

During tape play, the power cord has been

unplugged.

Plug in the power cord and press the

ON/STANDBY button.

Indicators and the display do not light up

while in standby mode.

Batteries or DC power is used to supply

the power.

Speciﬁcations

■■

Ampliﬁer

Speakers

Output Power

Full range

8 cm (3-3/16") × 2, 4 Ω

16 cm (6-5/16") × 2, 4 Ω

Super woofer

6 W per channel, min. RMS, at 4 Ω from 150 Hz to 15

kHz with no more than 10% total harmonic distortion.

20 W per channel woofer, min. RMS into 4 Ω at 60 Hz

with no more than 10% total harmonic distortion.

Input Sensitivity/Impedance (1 kHz)

Wireless Transmitter (VFT-001)

Power Requirements DC 3 V (“R6/AA(15F)” batteries [2])

Transmitting Frequencies

88.10 MHz, 88.30 MHz, 88.50 MHz,

88.70 MHz, 107.10 MHz, 107.30 MHz,

107.50 MHz, 107.70 MHz

AUX IN

300 mV/47 kΩ

MIC/GUITAR INPUT: Switchable

MIC

GUITAR

200 Ω – 2 kΩ (6.3 mm dia. plug)

100 kΩ – 1 MΩ (6.3 mm dia. plug)

Input terminal

Stereo mini plug

Frequency response 50 Hz to 12 000 Hz

Battery life (at normal temperature)

Output Sensitivity/Impedance (1 kHz)

Phones

16 Ω – 1 kΩ

Approx. 50 hours (with Alkaline batteries)

0 – 12 mW/ch output into 32 Ω

Approx. 20 hours (with Manganese batteries)

78 mm × 55 mm × 35 mm (W/H/D)

(3-1/8" × 2-3/16" × 1-7/16")

Dimensions

Mass

Cassette Deck

Frequency Response

Approx. 50 g (0.12 lbs) (without batteries)

Type II (High position) 60 Hz – 14 kHz

Wow and Flutter

0.15% (WRMS)

General

Dimensions

690 mm × 239 mm × 296 mm (W/H/D)

(27-3/16" × 9-7/16" × 11-11/16")

9.5 kg (21 lbs) (without batteries)

10.6 kg (23.4 lbs) (with batteries)

Disc Player

Dynamic range

90 dB

Mass

Signal-to-noise ratio 95 dB

Wow and Flutter

Unmeasurable

Power Speciﬁcations

Tuner

Power Requirements AC 120 V

, 60 Hz

WIRELESS

Tuning Range

FM Tuner

DC 15 V (“R20/D(13F)” batteries [10])

External DC 12 V (car battery via optional

CA-R120 car adapter)

87.50 MHz – 108.00 MHz

87.5 MHz – 108.0 MHz

Tuning Range

AM Tuner

Tuning Range

Antenna

Power Consumption 50 W (power on mode)

1.6 W (in standby mode)

530 kHz – 1 710 kHz

FM telescopic antenna

Ferrite core antenna for AM

Design and speciﬁcations are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

For U.S.A.

Download from Www.Somanuals.com. All Manuals Search And Download.

For U.S.A.

Download from Www.Somanuals.com. All Manuals Search And Download.

0106KMMMDWJEIN

Download from Www.Somanuals.com. All Manuals Search And Download.

POWERED WOOFER CD SYSTEM

CHAIN CD A WOOFER AMPLIFIE

RV-NB10B/RV-NB10W

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

LVT1539-002A

[C]

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings, Cautions and Others

Mises en garde, précautions et indications diverses

For U.S.A.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

The lightning ﬂash with arrowhead symbol,

installation. If this equipment does cause harmful interference

within an equilateral triangle is intended to alert

to radio or television reception, which can be determined by

the user to the presence of uninsulated

turning the equipment off and on, the user is encouraged to try

“dangerous voltage” within the product’s

to correct the interference by one of the following measures:

enclosure that may be of sufﬁcient magnitude to

Reorient or relocate the receiving antenna.

constitute a risk of electric shock to persons.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

The exclamation point within an equilateral

triangle is intended to alert the user to the

Consult the dealer or an experienced radio/TV technician for

presence of important operating and

help.

maintenance (servicing) instructions in the

literature accompanying the appliance.

For wireless transmitter

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

IMPORTANT NOTE:

ON/STANDBY button!

^CAUTION—

FCC Radiation Exposure Statement:

Disconnect the mains plug to shut the power off completely (the

STANDBY lamp goes off). When installing the apparatus, ensure

This equipment complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment. To maintain

compliance with FCC RF exposure compliance requirements,

please avoid direct contact to the transmitting antenna during

transmitting.

that the plug is easily accessible. The

ON/STANDBY button in

any position does not disconnect the mains line.

• When the unit is on standby, the STANDBY lamp lights red.

• When the unit is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

^ATTENTION—Touche

ON/STANDBY!

For Canada/pour le Canada

Déconnectez la fiche secteur pour mettre l’appareil complètement

hors tension (le témoin STANDBY l s’éteint). Lors de l’installation de

l’appareil, assurez-vous que la fiche soit facilement accessible. La

THIS DIGITAL APPARATUS DOES NOT EXCEED THE

CLASS B LIMITS FOR RADIO NOISE EMISSIONS

FROM DIGITAL APPARATUS AS SET OUT IN THE

INTERFERENCE-CAUSING EQUIPMENT STANDARD

ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE

DEPARTMENT OF COMMUNICATIONS.

touche

ON/STANDBY dans n’importe quelle position ne

déconnecte pas l’appareil du secteur.

• Quand l’appareil est en mode d’attente, le témoin STANDBY est

allumé en rouge.

• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.

L’alimentation ne peut pas être commandée à distance.

CET APPAREIL NUMERIQUE RESPECTE LES

LIMITES DE BRUITS RADIOELECTRIQUES

APPLICABLES AUX APPAREILS NUMERIQUES DE

CLASSE B PRESCRITES DANS LA NORME SUR LE

MATERIEL BROUILLEUR: “APPAREILS

CAUTION

To reduce the risk of electrical shocks, ﬁre, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

NUMERIQUES”, NMB-003 EDICTEE PAR LE

MINISTRE DES COMMUNICATIONS.

ATTENTION

Aﬁn d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret

de l’appareil.

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

L’utilisation de ce dispositif est autorisée seulement aux

conditions suivantes : (1) il ne doit pas produire de brouillage et

(2) l’utilisateur du dispositif doit être prêt à accepter tout

brouillage radioélectrique reçu, même si ce brouillage est

susceptible de compromettre le fonctionnement du dispositif.

G-1

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user

serviceable parts inside the unit; leave all servicing to qualiﬁed

service personnel.

CAUTION:

•

Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper or

cloth, etc., the heat may not be able to get out.

Do not place any naked ﬂame sources, such as lighted

candles, on the apparatus.

When discarding batteries, environmental problems must be

considered and local rules or laws governing the disposal of

these batteries must be followed strictly.

•

3. CAUTION:Visible and/or invisible class 1M laser radiation when

open. Do not view directry with optical instruments.

•

Do not expose this apparatus to rain, moisture, dripping or

splashing and that no objects ﬁlled with liquids, such as vases,

shall be placed on the apparatus.

IMPORTANT POUR PRODUITS LASER

1. PRODUIT LASER CLASSE 1

2. ATTENTION: N’ouvrez pas le couvercle supérieur. Il n’y a

aucune pièce réparable par l’utilisateur à l’intérieur de l’appareil;

conﬁez toute réparation à un personnel qualiﬁé.

3. ATTENTION: Rayonnement laser visible et/ou invisible de

classe 1M une fois ouvert. Ne pas regarder directement avec des

instruments optiques.

ATTENTION:

•

Ne bloquez pas les oriﬁces ou les trous de ventilation. (Si les

oriﬁces ou les trous de ventilation sont bloqués par un journal

un tissu, etc., la chaleur peut ne pas être évacuée

correctement de l’appareil.)

•

Ne placez aucune source de ﬂamme nue, telle qu’une bougie,

sur l’appareil.

Lors de la mise au rebut des piles, veuillez prendre en

considération les problèmes de l’environnement et suivre

strictement les règles et les lois locales sur la mise au rebut

des piles.

•

N’exposez pas cet appareil à la pluie, à l’humidité, à un

égouttement ou à des éclaboussures et ne placez pas des

objets remplis de liquide, tels qu’un vase, sur l’appareil.

[European Union Only]

[Union européenne seulement]

G-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for purchasing the JVC Powered Woofer CD System.

Before operating this system, read this manual carefully and thoroughly to obtain the best possible performance from your system, and retain

this manual for future reference.

Features

Here are some of the things that make your system both powerful and simple to use.

■ General

• With JVC’s COMPU PLAY you can turn on the system and automatically start the radio, disc player, or cassette deck

with a single touch. (Only when AC power is used.)

• With the supplied wireless transmitter, you can listen to auxiliary equipment such as a digital audio player (not

supplied) by wireless connection.

• Shoulder strap with carrying cases for the remote control and auxiliary equipment, and carrying handle

• ACS (Active Clear Sound) circuit for enhancing sound reproduction

• Super woofer volume control that provides powerful bass

• Sound mode control—reproducing various sound ﬁelds

• Remote control unit that operates the disc, cassette, tuner, and wireless functions

• Locking mechanism for disc and cassette door

• Microphone/guitar input

■ Disc playback mode includes Skip Play, Search Play, Repeat Play, Random Play, and Program Play.

■ Cassette player having full logic cassette mechanism, auto reverse, and auto tape mechanism.

■ A 45-station preset capability (30 stations in FM band and 15 stations in AM band) in addition to auto-seek and manual tuning.

■ Clock/timer functions, timer on/off with preset volume function, and sleep timer.

IMPORTANT CAUTIONS

1.Where to place the system

■

• Select a place which is level, dry and neither too hot nor too cold (between 5˚C and 35˚C).