HV-32D40BK
HV-28D40BK
INSTRUCTIONS
Integrated Digital Colour Television
Trade Mark of the DVB Digital Video Broadcasting
Project (1991 to 1996) Number: 3081
Download from Www.Somanuals.com. All Manuals Search And Download.
How to move the TV
When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful
not to trap your hands when putting the TV down.
1
2
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
• Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long
period of time, it is recommended that you
disconnect the power cord from the main
outlet.
• The main power button on the TV does not
fully isolate the TV from the mains supply. If
you are not going to use this TV for a long
period of time, be sure to disconnect the mains
plug from the mains outlet.
Avoid improper installation and never put the unit where good
ventilation is not possible.
When installing this TV, distance recommendations must be
maintained between the set and the wall, as well as inside a tightly
enclosed area or piece of furniture.
Adhere to the minimum distance guidelines shown for safe operation.
Failure to heed the following precautions may result in damage to the TV or
remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.
D.I.S.T. demonstration
To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration:
Press the yellow button, TV/DTV button, p p buttons or any of the number buttons.
NOTE:
Due to static electricity, the TV may be covered with dust.
If this happens, wipe the TV with a soft cloth being careful not to scratch the TV.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital terrestrial broadcasting (DVB-T) service area
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial
broadcasting, depending on the area in which you live, you may not be able to receive Digital
terrestrial broadcasting (DVB-T).
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW
website etc.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV ...................................7
Connecting the aerial................................. 7
Connecting the power cord to the AC
outlet....................................................... 8
Putting the batteries into the remote
control..................................................... 8
Initial settings ............................................. 8
T-V LINK functions................................... 11
PICTURE MODE...................................... 29
SHARP..................................................... 29
TV buttons and functions......................13
Turn the TV on from standby mode ......... 13
Choose a TV channel .............................. 13
Adjust the volume .................................... 14
3D CINEMA SOUND................................ 33
Remote control buttons and
functions..............................................15
Turn the TV on or off from standby mode ... 15
Choose a TV channel and watch images
from external devices ........................... 16
Adjust the volume .................................... 17
Information function ................................. 17
ZOOM function......................................... 18
3D CINEMA SOUND function.................. 20
Using the MULTI-PICTURE function ....... 20
Using the GUIDE ..................................... 22
Displaying the Subtitles............................ 24
Operating a JVC brand VCR or DVD
DECODER (EXT-2).................................. 41
ATTENUATOR......................................... 44
player.................................................... 24
Teletext function ....................................25
Basic operation (Digital)........................... 25
Basic operation (Analogue)...................... 26
Using the List Mode ................................. 26
Hold.......................................................... 27
Sub-page ................................................. 27
Reveal...................................................... 27
Size.......................................................... 27
Index ........................................................ 27
Cancel...................................................... 27
DTV menu............................................... 45
Timers (DTV Timer Recording)................ 45
Configuration............................................ 47
Edit PR List .............................................. 49
Installation................................................ 52
Common Interface.................................... 52
Additional preparation .......................... 53
Connecting external equipment ............... 53
Troubleshooting .................................... 56
Specifications ........................................ 59
Using the TV’s menu..............................28
Basic operation ........................................ 28
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Caution
• Turn off all the equipment including the TV before connecting anything.
Connecting the aerial
• The connecting cables are not provided.
• For further details, refer to the manuals provided with the devices to be connected.
For example
antenna terminal such as a VCR,
follow A → B → C in the diagram
opposite.
Aerial
Back of the TV
75-ohm
Coaxial
„ If you connect the antenna
Cable
To use the T-V LINK functions, you must
have a T-V LINK compatible VCR
EXT-
4
connected by a SCART cable C to the EXT-
2 terminal on the TV. For details about T-V
LINK functions, see “T-V LINK functions”
on page 11.
EXT-1
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
• To connect more equipment, please see
“Connecting external equipment” on
page 53.
• To connect additional audio equipment,
see “Connecting speakers/amplifier” on
page 55.
21-pin
SCART
Cable
75-ohm
Coaxial
Cable
• If you connect a decoder to a T-V LINK
compatible VCR, set the DECODER
(EXT-2) function to ON. For details, see
“DECODER (EXT-2)” on page 41.
Otherwise, you will not be able to watch
scrambled channels.
To Aerial
Input
VCR
• When receiving Digital terrestrial
broadcasting (DVB-T), reception can
suddenly be lost if the signal becomes
weak. Use a correctly installed high-
performance antenna.
To Aerial
Output
AV IN/OUT
Terminal
• When connecting via a device with an
antenna terminal such as a VCR, depending
on the connection method, the signal may
be weakened. If this happens, use a booster
to increase the signal strength.
• In areas with a lot of radio communication
such as near ports or airports, noise may
be introduced into the picture or sound. In
such cases, reception may be improved by
using a high-performance antenna.
• Read the instruction manual of the
devices which you connect to the TV.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
„ Rear Panel
Putting the batteries into the
remote control
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
Not use
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
• Follow the warnings printed on the
batteries.
R
• Battery life is about six months to one
year, depending on how much you use the
remote control.
• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.
• If the remote control does not work
properly, replace the batteries.
1 Aerial socket (page 7)
2 EXT-1 terminal (pages 7, 42, 53)
3 EXT-2 terminal (pages 7, 11, 42, 53)
4 EXT-3 terminal (pages 42, 53)
5 EXT-4 terminal (pages 42, 53)
6 AUDIO OUT terminal (page 55)
7 Common Interface terminal (page 52)
Initial settings
When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.
Connecting the power cord to
the AC outlet
Caution
• Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
TV/DTV
7
buttons
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
When the Automatic Search has
finished, the EDIT PR LIST menu
appears
1 Press the main power button on the
TV
The power lamp lights green and the JVC
logo appears.
EDIT PR LIST
1
BBC ONE
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
Select
Delete
Edit Name
Lock
Favourites
More..
Select function
Select PR OK Watch PR
Main power
button
Power lamp
D0202-EN
• If you want to, you can now edit the
programme numbers (PR) using the
EDIT PR LIST function. For details,
see “Edit PR List” on page 49.
• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
Perform the initial settings with
“Installation” (see page 52) in the
DTV menu and “AUTO PROGRAM
(Analogue)” (see page 36) in the SET
UP menu.
• To receive SKY 1 you need a satellite
tuner. You must have the satellite tuner
set to SKY 1 before starting the AUTO
PROGRAM function which follows.
• If you do not want to edit programme
numbers (PR), go to the next step.
3 Press the H button
The EDIT PR LIST menu disappears and
the Analogue terrestrial broadcasting
AUTO PROGRAM starts.
The AUTO PROGRAM menu appears
and received TV channels are
automatically stored in the programme
numbers (PR).
2 Press the a button
The Digital terrestrial broadcasting
(DVB-T) Automatic Search starts.
The Digital terrestrial broadcasting
(DVB-T) channels which can be received
are automatically registered.
>> AUTO PROGRAM
CH 28
14%
OK
Installation > Automatic Search
D0004-EN
Channels:
BBC ONE
BBC TWO
BBC THREE
BBC NEWS 24
BBCi
• To cancel the AUTO PROGRAM
function:
Press the TV/DTV button.
CBBC Channel
UHF
CH:68
100%
MENU
Cancel, go to Installation
Cancel, go to DTV
BACK
D0201-EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
After the AUTO PROGRAM has
Now, the initial settings are complete,
and you can watch the TV
finished, the EDIT menu appears
and Channel 5 are automatically set to the
programme numbers PR1 to PR5. If the
TV doesn’t receive one of these TV
channels, that programme number (PR)
will not be set. Programme number PR6 is
not normally set.
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
ID
MANUAL
OK
MOVE
• If a TV channel you want to view is not
set to a programme number (PR), you can
set it manually. To set an Analogue
terrestrial broadcasting channel, see
“EDIT/MANUAL (Analogue)” on
page 36. To set a Digital terrestrial
broadcasting (DVB-T) channel, see
“Manual Search:” on page 52.
• The AUTO PROGRAM function does not
set the programme number PR 0 (AV) for
your video cassette recorder. You will
need to set this using the MANUAL
function.
INSERT DELETE
D0038-EK
• If you want to, you can now edit the
programme numbers (PR) using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL (Analogue)” on
page 36.
• If you do not want to edit programme
numbers (PR), go to the next step.
4 Press the a button to display the
T-V LINK menu
T-V LINK
• In some areas you may get TV reception
from more than one transmitter, for
example different ITV regions. In this
case each TV channel could be set twice.
If this happens, the first set of channels
will have the stronger signal. If you want
to delete the second set of channels, you
will have to do it manually (see page 36).
DOWNLOAD TV
RECORDING DEVICE
OK
EXIT
D0005-EN
If you do not have a T-V LINK
compatible VCR connected:
Press the TV/DTV button to exit the T-V
LINK menu.
For users in the UK:
If you have any problems setting up your
new TV, please call the
Helpline on 0870 330 5000.
The T-V LINK menu disappears.
If you have a T-V LINK compatible
VCR connected to the EXT-2
terminal:
Follow the operating procedure
“Downloading the data to VCR” on
page 11 to transmit the Programme
number (PR) data.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
„ Downloading the data to VCR
You can transmit to the latest Analogue
terrestrial broadcasting Programme numbers
(PR) data to a VCR with the T-V LINK
function.
T-V LINK functions
When you have a T-V LINK compatible
VCR connected to the EXT-2 Terminal on
the TV, it is easier to set up the VCR and to
view videos. T-V LINK uses the following
features:
Caution
• This only works when a T-V LINK
compatible VCR is connected to the
EXT-2 terminal.
• This only works when the T-V LINK
menu is being displayed.
To use T-V LINK functions:
A “T-V LINK compatible VCR” means a
JVC video cassette recorder with the T-V
LINK logo, or with one of the following
logos. However, these VCRs may support
some or all of the features described earlier.
For details, see your VCR instruction
manual.
T-V LINK
DOWNLOAD TV
RECORDING DEVICE
“Q-LINK” (a trademark of Panasonic
Corporation)
OK
EXIT
“Data Logic” (a trademark of Metz
Corporation)
“Easy Link” (a trademark of Phillips
Corporation)
D0005-EN
1 Turn on the VCR
2 Press the a button
“Megalogic” (a trademark of Grundig
Corporation)
“SMARTLINK” (a trademark of Sony
The data transmission begins.
T-V LINK TV
RECORDING DEVICE
Corporation).
TRANSFER. . . . .
D0037-EN
„ Pre-set download
The T-V LINK menu disappears once the
data transmission ends.
The VCR will automatically download the
registered data on the TV Analogue
terrestrial broadcasting channels from the
TV. This means you do not need to set up the
program channels on your VCR manually.
The preset download function automatically
begins when the initial setting is complete or
whenever you carry out the AUTO
When the T-V LINK menu is
changed over to another menu:
The TV has finished its menu. This new
menu is operated from the VCR. See the
VCR instruction manual for what to do
next.
PROGRAM or EDIT/MANUAL functions.
If “FEATURE NOT AVAILABLE”
appears at the T-V LINK menu:
Check the following three items. Then
press the 2 button to retry data
transmission.
• Has a T-V LINK compatible VCR
been connected to the EXT-2
terminal?
• Has the VCR power been turned on?
• Does the SCART cable that is
connected to the EXT-2 terminal to T-
V LINK compatible VCR have all its
proper connections?
You can also carry out this function using
your VCR controls.
When “FEATURE NOT AVAILABLE” is
displayed:
If “FEATURE NOT AVAILABLE” is
displayed, the download was not performed
correctly. Before trying to download again,
check that:
• the VCR power is turned on
• the VCR is T-V LINK compatible
• the VCR is connected to the EXT-2
terminal
• the SCART cable is fully wired.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
When the VCR is not ready, the following
messages are displayed.
„ Direct Rec
“What You See Is What You Record”
You can easily record to VCR the images
that you are watching on the TV.
ERROR
MESSAGE
Cause and
countermeasure
For details, read the manual for your VCR.
Use your VCR controls. “DEVICE IS
RECORDING” is displayed.
NO
The VCR is not able to
RECORDING record.
Check the VCR.
NO
The TV input is set to EXT-4.
You cannot carry out Direct Rec using your
TV’s control.
RECORDING Since the EXT-4 picture
POSSIBLE
cannot be output to EXT-2,
DIRECT REC is not possible.
Generally, the VCR cannot record a TV
channel that it cannot receive properly on its
own tuner, even if you can view that TV
channel on the TV. However, some VCRs
can record a TV channel by using the TV’s
output if that channel can be viewed on the
TV. For details, see your VCR instruction
manual.
NO
The RECORDING DEVICE
RECORDING, is not ready to record. Check
MEDIA
PROBLEM
the VCR tape.
NO
The RECORDING DEVICE
RECORDING, cannot record as it is
DEVICE BUSY recording or playing. Check
the VCR.
Do not turn the TV off in the following
cases.
• when recording images from an external
device connected to the TV (for example
a camcorder)
Refer to the VCR instruction manual.
• when recording a TV channel after it has
been unscrambled on a decoder
• when recording a TV channel by using the
TV’s output because the VCR’s own
tuner cannot properly receive that
channel.
• when recording Digital terrestrial
broadcasting (DVB-T).
If you change channels or perform
other operations while a Digital
terrestrial broadcasting (DVB-T)
channel is being recorded, a window
appears asking whether to stop the
recording.
Press the a button to stop the
recording, or the TV/DTV button to
continue the recording.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TV buttons and functions
Turn the main power on
Press the main power button on the
TV.
The power lamp lights red and your TV is in
standby mode.
• If the power lamp lights green, the TV is
already on.
To turn the main power off:
Press the main power button again.
The power lamp goes off.
Caution
• The main power button on the TV does
not fully isolate the TV from the AC
supply. If you are not going to use the TV
for a long period, be sure to disconnect
the AC plug from the AC socket.
Turn the TV on from standby
mode
Press the P p buttons to turn the TV
on from standby mode
Choose a TV channel
S
R
L/MONO
EXT-5
P
Press the P p buttons to choose a
terminal
The EXT terminal cannot be chosen when
watching Digital terrestrial broadcasting
(DVB-T).
S
R
L/MONO
EXT-5
P
terrestrial broadcasting (DVB-T):
1 Press the r (Volume) button
2 Press the r (Volume) button
again when the volume level
indicator appears
See the pages in parentheses for details.
1 Main power button (pages 9, 13)
2 Power lamp (pages 9, 13)
3 Remote control sensor
4 r (Volume) button (page 14)
5 P p buttons/ q buttons (page 13)
6 Headphone jack (mini jack) (page 53)
7 EXT-5 terminal (pages 42, 53)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
1 Muting button
2 Number buttons
3 Information button
4 Colour button
1
2
~
!
5 TV/DTV button
6 7 buttons
7 g (Text) button
8 p p buttons
9 VCR/DVD/Teletext control buttons
0 p buttons
- c button
= 3 button
~ # (Standby) button
! VCR/TV/DVD switch
@ G button
# H button
$ a button
3
4
5
@
#
$
% b button
^ r (Volume) q buttons
& GUIDE button
* SUBTITLE button
( X (Multi) button
) f/g (Freeze/Swap) button
6
7
%
^
Turn the TV on or off from
standby mode
8
Press the # (standby) button to turn
the TV on or off.
When the TV is turned on, the power lamp
&
*
9
0
lights green.
• The power can be turned on by pressing
the TV/DTV button, p p buttons or
Number buttons.
(
)
-
=
To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to a position other than TV,
the TV will not be turned on or off even if
the # button is pressed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• You can choose a video input signal
from the S-VIDEO signal (Y/C signal)
and regular video signal (composite
signal). For details, see “S-IN (S-
VIDEO input)” on page 42.
Choose a TV channel and
watch images from external
devices
• If you do not have a clear picture or no
colour appears, change the colour
system manually. See “COLOUR
SYSTEM” on page 31.
• If you choose an EXT terminal with no
input signal, the EXT terminal number
becomes fixed on the screen.
• If the picture is tilted, correct it. See
“PICTURE TILT” on page 40.
„ Switching between Digital
terrestrial broadcasting (DVB-T)
and Analogue terrestrial
broadcasting.
• This TV set has a function which can
automatically change over the input
according to a special signal output
from an external device. (The EXT-4
and EXT-5 terminals do not support
this function.)
• Since this TV is designed to make full
use of the resolution of the original
video source, the motion may appear
unnatural when the video source is
input with 625p progressive-scanning
component signals.
If this happens, change the output
setting of the connected device to 625i
interlace-scanning component signal
output. See the instructions that came
with the device for more information.
Press the TV/DTV button.
The broadcasting is switched every time the
button is pressed.
„ Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
• PR 6 → press 6
• PR 12 → press 1 and 2
• PR 123 → press 1, 2 and 3
„ Use the p p buttons:
Press the p p buttons to
choose the programme number
(PR) you want.
To return to a TV channel:
Press the TV/DTV button, the p p buttons
or the number buttons.
• For Digital terrestrial broadcasting (DVB-
T), if the FAVOURITE setting in the
“Edit PR List” (see page 49) has been set,
only that programme number (PR) can be
chosen.
• For Analogue terrestrial broadcasting, an
EXT terminal can also be chosen.
„ Use the AV button:
Press the AV button to choose an
EXT terminal.
TV mode
EXT modes
Analogue
terrestrial
broadcasting
EXT-2
EXT-1
or
EXT-3
or
S3
E3
Digital
terrestrial
broadcasting
(DVB-T)
EXT-5
EXT-4
or
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
To use the programme number PR 0
(AV):
Information function
When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL (Analogue)” on page 36.
Pressing the G button changes the choice as
follows:
When watching Digital terrestrial
broadcasting (DVB-T):
When the h (Information) button is pressed,
the programme information appears for
approximately 1 minute.
ITV News
CH61
41
Now: 13:00-14:00 Steve Scott
Next: 14:00-14:30 Steve Scott
13:19
D0203-EN
TV mode
EXT modes
• When the h (Information) button is
pressed while the information is being
displayed, the information disappears.
Analogue
terrestrial
broadcasting
EXT-2
PR 0
EXT-1
or
EXT-3
• The time display in the programme
information uses the time information
which is included in the Digital terrestrial
broadcasting (DVB-T). Depending on the
channel, the time information may not be
correct.
or
S3
E3
Digital terrestrial
broadcasting
(DVB-T)
EXT-5
EXT-4
or
• The VCR sends its playback image along
the aerial cable as an RF (radio frequency)
signal.
When watching Analogue terrestrial
broadcasting:
You can see the channel number of the
programme you are watching, the current
time or the PR LIST.
• Also see your VCR instruction manual.
From the PR LIST, you can choose a channel
or EXT terminal.
Adjust the volume
Press the r q buttons to adjust
the volume.
The volume indicator appears and the
volume changes as you press the r q
buttons.
Press the
display the information you want to
see.
Pressing the
the display as follows:
(Information) button to
h
(Information) button changes
h
„ Muting the sound
PR LIST
Press the (muting) button to
l
PR
ID
Channel number display
12 : 00
turn off the sound.
AV
01
02
03
04
05
06
07
08
09
BBC1
Pressing the (muting) button again
l
restores the previous volume level.
No indication
OK
-10
+10
D0011-EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Channel number display:
ZOOM function
The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the EXT
terminal number is displayed.
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
Time display:
The current time of the teletext data is
AUTO:
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.
• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 32.
• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.
• When watching a 16:9 FULL programme
with Digital terrestrial broadcasting
(DVB-T), the aspect ratio is FULL.
displayed.
If the TV has not received a TV channel that
has teletext programmes since it was turned
on, the time display is blank. To view the
current time, choose a TV channel that has
teletext programmes.
displayed when watching videos.
PR LIST:
The programme number (PR) and EXT
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or EXT terminal
with the 7 buttons will display the
chosen programme or EXT terminal.
• For programme numbers (PR) for which
the CHILD LOCK function is set, the n
(CHILD LOCK) mark is displayed. For
details see “CHILD LOCK” on page 34.
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.
PANORAMIC:
This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.
• The top and bottom of the picture are
slightly cut off.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
14:9 ZOOM:
„ Choose the ZOOM mode
This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.
1 Press the c button to display
the ZOOM menu
ZOOM
AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect
ratio) to the full screen.
OK
D0009-EN
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a
button
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.
The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.
• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.
FULL:
This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.
„ Adjusting the visible area of the
picture
• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.
If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.
1 Press the c button
• When you use this TV’s output signal to
record a Digital terrestrial broadcasting
(DVB-T) 16:9 broadcast, it will be
recorded with its picture squeezed into a
4:3 aspect ratio picture.
Use the FULL mode to restore the picture
to its original shape when playing the
recording.
The ZOOM menu appears.
2 Press the a button to display the
ZOOM mode indicator
The indicator appears.
16 : 9 ZOOM
D0010-EN
3 While it is displayed, press the 6
buttons to change the position of
the picture
• You cannot adjust the visible area in
REGULAR or FULL mode.
• Some menu displays can be cut off when
you move the visible area up or down
while watching Digital terrestrial
broadcasting (DVB-T).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
3D CINEMA SOUND function
Using the MULTI-PICTURE
function
You can enjoy sounds with a wider
ambience.
• This function does not work for the sound
from headphones.
When watching Digital terrestrial
broadcasting (DVB-T):
1 Press the X button
Press the 3 button and choose
“ON”, “MONO” or “OFF”.
The MULTI-PICTURE menu appears.
ON:
1
2
12
Choose to add the 3D CINEMA SOUND
effect to stereo sound.
D0101-EN
MONO:
2 Press the 5 buttons and choose
2, then press the a button
Choose to add the 3D CINEMA SOUND
effect to mono sound.
OFF:
Choose to return to one screen.
1
Choose to cancel the 3D CINEMA SOUND
effect.
D0102
• The 3D CINEMA SOUND effect can be
adjusted with the “3D CINEMA
SOUND” menu (see page 33).
Choose to change to 2-pictures multi.
2
D0103
2-pictures multi:
Using the FREEZE function
This function can only be used when
watching Analogue terrestrial
broadcasting.
Main-
picture
Sub-
picture
D1056-EN
You can view the current programme as a
still picture.
This cannot be chosen when watching
Digital terrestrial broadcasting (DVB-T).
12
D0104
1 Press the f button
The still picture of the current picture will
appear.
• You can watch Digital terrestrial
broadcasting (DVB-T) in the main-
picture. You can watch the Analogue
terrestrial broadcasting or EXT picture
in the sub-picture.
current
still picture
programme
• When the Digital terrestrial
broadcasting (DVB-T) in the main-
picture is 16:9 FULL, the main-picture
aspect ratio is 16:9.
• The main-picture sound is emitted
from the TV speaker. If headphones
are connected, you can listen to the
sub-picture sound. Adjust the
headphone volume with
HEADPHONE VOLUME in the
SOUND menu. The main-picture
sound cannot be listened to with the
headphones.
D1056-EN
To cancel the FREEZE function:
Press the f button, the p p buttons or
the number buttons.
• The FREEZE function does not work
while a sub-picture is displayed.
• The still picture cannot be output from
the TV.
• The FREEZE function does not work
for pictures of 1125i signal.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• Choose the main-picture channel by
pressing the p p buttons. Choose
the sub-picture channel by pressing the
p buttons.
12-pictures multi:
Still
pictures
• You cannot use the g (swap) button.
When watching Digital terrestrial
broadcasting (DVB-T), the main-
picture and sub-picture cannot be
switched.
Moving
picture
D0058-EN
• When set to 2-pictures multi, you can
view a TV picture and a picture from
an external device. You can not view a
TV picture on more than one screen at
the same time.
• 1125i, 625p, and 525p signal pictures
cannot be displayed as the sub-picture.
To return the multi-picture to one
screen:
Press the X button, press the 5
buttons to choose one screen, and then
press the a button.
• When 12-pictures multi is set, pictures
from external devices are not
displayed.
• When set to 2-pictures multi, the main-
picture can be changed by pressing the
p p buttons. The sub-picture screen
can be changed by pressing the p
buttons.
• Pressing the TV/DTV button will also
return the display to one screen.
When watching Analogue terrestrial
broadcasting:
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the p buttons.
1 Press the X button
The MULTI-PICTURE menu appears.
1
2
12
D0101-EN
2 Press the 5 buttons to choose
the number of screens and then
press the a button
Changing the sub-picture
Displaying the next or
previous 12 screens
Choose to return to one screen.
1
• When set to 2-pictures multi, press the
g (swap) button to switch the main-
picture and sub-picture.
D0102
Choose to change to 2-pictures multi.
2
•
2-pictures multi function does not
work for a picture of 1125i signal.
D0103
• A picture of 625p or 525p signal
cannot be displayed as the sub-picture.
Pay attention to the following.
Choose to change to 12-pictures multi.
12
D0104
- When the EXT-4 picture is a picture
of 625p or 525p signal, you cannot
choose EXT-4 with the p buttons.
- When the EXT-4 picture signal is
changed to 625p, 525p or 1125i
2-pictures multi:
Main-
picture
Sub-
picture
signal while the EXT-4 picture is
displayed as the sub-picture, the 2-
pictures multi function is cancelled.
D1056-EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
- The pictures cannot be swapped
when a picture of 625p or 525p
signal from EXT-4 is being
Using the GUIDE
• Use when watching Digital
terrestrial broadcasting (DVB-T).
displayed as the main picture.
• Do not press the g (swap) button
while you are recording the TV output
on the VCR. If you do, the TV output
signal will change.
The guide appears when the GUIDE button
is pressed while watching Digital terrestrial
broadcasting (DVB-T).
• You cannot view a scrambled channel
in the sub-picture. If the g (swap)
button is pressed when viewing a
scrambled channel in the main-picture
using an external decoder, the channel
you have been viewing in the sub-
picture will appear in both the main-
picture and sub-picture.
Electronic Programme Guide
1
BBC ONE
13:12
The Rugby World Cu... 07:45-15:10
Fiji v USA, Italy v Tonga & Samoa v
Uruguay
Channels
Current Event
Next Event
1. BBC ONE
2. BBC TWO
7. BBC THREE
The Rugby Worid Cup... Movies Now
• When set to 2-pictures multi and the
headphones are connected, the sound
for the main-picture is output from the
TV speakers and the sound from the
sub-picture is output from the
30. CBBC Channel
40. BBC NEWS 24
Select PR OK Watch PR
Next Event
More..
D0204-EN
headphones.
1 Quarter-screen
- Adjust the volume of the sub-picture
sound from the headphones with
“HEADPHONE VOLUME” in the
“SOUND” menu (see page 33).
- The main-picture sound can not be
heard through the headphones.
• When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.
• The BLUE BACK function does not
work when the MULTI-PICTURE
function is being used.
• The ZOOM function does not work
when the MULTI-PICTURE function
is being used.
The programme you are watching is
shown.
• Sometimes you may notice a drop in
picture quality while watching your
programme in the quarter-screen. This
is not a fault.
2 Programme name, broadcast time
and brief description of programme
The programme name, broadcast time and
a brief description of the programme are
displayed for the programme chosen from
the current event column or next event
column.
3 Channel column
4 Current event column
5 Next event column
To return the multi-picture to one
screen:
Press the X button, press the 5
buttons to choose one screen, and then
press the a button.
• Pressing the TV/DTV button will also
return the display to one screen.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Pressing the h (Information) button to
display the help screen. Press it again to
return to the guide screen.
3 Press the a button
The scheduled icon appears at the right of
the chosen programme and the scheduling
is completed.
Electronic Programme Guide
1
BBC ONE
13:12
The Rugby World Cu... 07:45-15:10
Scheduled icon
Fiji v USA, Italy v Tonga & Samoa v
Uruguay
Channels
Current Event
Next Event
1. BBC ONE
2. BBC TWO
7. BBC THREE
The Rugby Worid Cup... Movies Now
Red: Page up
30. CBBC Channel
40. BBC NEWS 24
Green: Page down
TV/DTV: Go to DTV
Guide: Leave guide
Back: Go to previous
MENU
OK
Select PR OK Set reminder On/Off
Current Event
More..
i: Exit help
Next Event More..
D0206-EN
Select PR OK Watch PR
D0205-EN
• Steps 1 to 3 can be repeated to schedule
more programmes.
Help screen
• When the GUIDE, TV/DTV, H or
b buttons are pressed, the guide
screen disappears and the normal screen
returns.
„ Choosing a channel
1 Press the 6 buttons and choose
a channel
The programme name, broadcast time and
a brief description of the programme are
displayed.
• Press the red and green buttons to
scroll the channel column.
When the TV is being watched, it
automatically changes to the channel of the
scheduled programme when the start time of
the scheduled program is reached.
• The scheduling function does not work
when the TV is turned off.
2 Press the a button
The chosen programme appears on the
quarter-screen.
Cancelling a scheduled programme.
Display the guide screen, choose a
programme which has the scheduled icon
(
), and press the a button.
• When the GUIDE, TV/DTV, H or
b buttons are pressed, the guide
screen disappears and the normal screen
returns.
The icon disappears and the scheduling is
cancelled.
„ Checking programme details
Press the 7 buttons and
choose a programme from the
Current Event or Next Event columns
The programme name, broadcast time and a
brief description of the chosen programme
appear.
„ Set reminder
When you schedule a programme, you will
not miss a programme that you want to
watch.
1 Press the 5 buttons and choose
the Next Event column
• Press the red and green buttons to scroll
the channel column.
2 Press the 6 buttons and choose
the program that you want to
schedule
• When the GUIDE, TV/DTV, H or
b buttons are pressed, the guide
screen disappears and the normal screen
returns.
The programme name, broadcast time and
a brief description of the chosen
programme are displayed.
• Press the red and green buttons to
scroll the channel column.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Displaying the Subtitles
Operating a JVC brand VCR or
DVD player
• Use this function when watching
Digital terrestrial broadcasting
(DVB-T).
These buttons will operate a JVC brand VCR
or DVD player. Pressing a button that looks
the same as the device’s original remote
control button has the same effect as the
original remote control.
With Digital terrestrial broadcasting (DVB-
T), some programmes are broadcast with
subtitles. Subtitles can be displayed when
watching these programmes.
1 Set the VCR/TV/DVD Switch to the
VCR or DVD position
Press the SUBTITLE button when
watching Digital terrestrial
VCR:
broadcasting (DVB-T)
When you are operating the VCR, set the
switch to the VCR position.
• You can turn the VCR on or off with
the # (standby) button.
“Subtitle ON” appears at the top-left of the
screen and, when the programme has
subtitles, the subtitles are displayed.
DVD:
Subtitle ON
D0207-EN
When you are operating the DVD player,
set the switch to the DVD position.
• You can turn the DVD player on or off
with the # (standby) button.
• You can also press the H or
T button and display the
DVD disc menu screen, and then
operate by pressing the 7
buttons.
• When the SUBTITLE button is pressed
again, “Subtitle OFF” appears and the
subtitles disappear.
2 Press the VCR/DVD Control Button
to control your VCR or DVD player
• If your device is not made by JVC,
these buttons will not work.
• Even if your device is made by JVC,
some of these buttons may not work,
depending on the device you are using.
• You can use the p buttons to choose
a TV channel the VCR will receive, or
choose the chapter the DVD player
plays back.
• Some models of DVD player use the
p buttons for both operating the fast
forward/backward functions and for
choosing the chapter. In this case, the
253 buttons do not work.
You cannot turn the TV on or off when the
VCR/TV/DVD switch is set to the VCR or
DVD position.
When you turn the TV on or off, set the
VCR/TV/DVD switch to the TV position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
1 Press the g button
The digital teletext information appears.
BBC ONE
Powers
For a full list of sections,
press SELECT
VCR/TV/
DVD switch
Contact info
CBeebies Home
Music
Number
buttons
Taking Care
NEWS
SPORT
WEATHER
MAIN MENU
Press TEXT to exit
B
B
C
Colour
buttons
D0208-EN
2 Operate it with the colour buttons,
7 buttons and a button
The operation method may differ depending
on the contents of the digital teletext.
Operate in accordance with the instructions
displayed on digital teletext screen.
• When “Press SELECT” or similar
message appears on the screen, press
the a button.
7
buttons
• When the g (Text) button is pressed, the
TV returns to television broadcasting.
• With Digital terrestrial broadcasting
(DVB-T), in addition to digital teletext
broadcasting at the same time as normal
broadcasting, there are also channels with
• The aspect ratio when watching a channel
with just digital teletext broadcasting is
the same as the aspect ratio of the picture
watched previously.
Basic operation (Digital)
• When you press the g (Text) button
while subtitles are on, the subtitles are
turned off. When you press the g (Text)
button again, the digital teletext screen is
displayed.
When watching Digital terrestrial
broadcasting (DVB-T):
With Digital terrestrial broadcasting (DVB-
T), in addition to pictures and sound, you can
also watch digital teletext.
Digital teletext is sometimes broadcast at the
same time as normal broadcasting.
The functions described on pages
26 and 27 cannot be used with
digital teletext.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
When watching Analogue terrestrial
broadcasting:
Using the List Mode
You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.
Basic operation (Analogue)
You can view two types of teletext
broadcasts on the TV:
FLOF (Fastext) and WST.
„ To store the page numbers:
1 Press B button to go into the
List mode
1 Choose a TV channel with a teletext
broadcast
The page numbers you have stored are
displayed at the bottom of the screen.
2 Set the VCR/TV/DVD switch to the
TV position
2 Press a colour button to choose a
position. Then press the number
buttons to enter the page number
3 Press g (Text) button to display
the teletext
Pressing g (Text) button changes the
mode as follows:
3 Press and hold down the A (Store)
button
TEXT
TEXT
---
---
The four page numbers blink white to
show that they are stored in memory.
TV mode
TV and text mode
„ To call up a stored page:
TEXT
TEXT
---
---
1 Press the B button to enter the
List mode
D1043-EN
Text mode
2 Press a colour button having a
stored page
4 Choose a teletext page by pressing
the p p buttons, number buttons
or colour buttons
To exit the List mode:
Press the B button again.
To return to the TV mode:
Press the TV/DTV button or g (Text)
button.
• If you have trouble receiving teletext
broadcasts, consult your local dealer or
the teletext station.
• The ZOOM function will not work in
the TV and text mode or Text mode.
• You cannot operate menus when
viewing a teletext programme.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
Hold
Size
You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.
You can double the height of the teletext
display.
Press the F (Size) button
Press the C (Hold) button
Hold indication
To cancel the Hold function:
Press C (Hold) button again.
Sub-page
Index
Some teletext pages include sub-pages that
are automatically displayed.
You can return to the index page instantly.
Press the G (Index) button
Returns to page 100 or a previously specified
page.
1 Choose a teletext page that
includes sub-pages
Sub-page numbers that can be viewed are
automatically displayed at the top of the
screen.
Cancel
You can search for a teletext page while
watching TV.
2 Press the 5 buttons to choose a
sub-page number
1 Press the number button to enter a
page number, or press a colour
button
Reveal
Some teletext pages include hidden text
(such as answers to a quiz).
The TV searches for a teletext page.
You can display the hidden text.
2 Press H (Cancel) button
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
Each time you press the E (Reveal)
button, text is hidden or revealed
3 Press H (Cancel) button to return
to a teletext page when the page
number is on the screen
• The TV mode cannot be resumed by
pressing the H (Cancel) button. To
return to the TV mode press b.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
This TV has a number of functions you can
operate using menus. To use all your TV’s
functions, you need to understand the basic
menu operating techniques fully.
Types of menu
PICTURE menu
(see page 29)
D0106
D0107
D0108
D0109
SOUND menu
(see page 33)
Buttons used to operate the menus
TV/DTV
FEATURES menu
(see page 34)
SET UP menu
(see page 36)
DTV menu
(see page 45)
D0224
The menu guide area can be made to appear
and disappear for some menus.
While the menu is displayed, press the h
button to change between the guide area
being displayed and not displayed.
Basic operation
1 Press the H button to display
the menu bar
>> 4:3 AUTO ASPECT
DTV
PANORAMIC
REGULAR
14:9 ZOOM
D0105-EN
OK
2 Press the 5 buttons to choose
the menu you want to use and then
press the a button
D0017-EN
Guide area
DTV
D1105-EN
Chosen
menu
Chosen
menu name
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
3 Press the 6 buttons to choose
the item to be set, press the 5
buttons to set the item, and then
press the a button
D1017-EN
• The guide area for some menus will still
be displayed even if the h button is
pressed. This is not a fault.
If there are sub-menus, use the 7
buttons to operate them.
• Press the b button to return to
the previous menu.
• Press the TV/DTV or H button
to exit from the menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
PICTURE
COLOUR
STANDARD
PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
You can adjust the picture colour.
2 :lighter
HUE
COLOUR TEMP.
FEATURES
3 : deeper
COOL
RESET
HUE
OK
D0014-EN
You can adjust the picture tint.
2 :reddish
3 : greenish
• While the PICTURE menu is displayed,
pressing the blue button will set the
CONTRAST, BRIGHT, SHARP,
COLOUR, HUE settings to their default
settings.
• You can change the HUE setting (picture
hue) when the colour system is NTSC
3.58, or NTSC 4.43.
COLOUR TEMP.
PICTURE MODE
You can select one of three COLOUR
TEMP. modes (three tones of white) to adjust
the white balance of the picture. Since white
is the colour which is used as a reference for
all the other colours, changing the COLOUR
TEMP. mode affects the appearance of all
the other colours on the screen.
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
BRIGHT:
Heightens contrast and sharpness.
COOL:
STANDARD:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
Standardizes picture adjustment.
SOFT:
Softens contrast and sharpness.
NORMAL:
The normal white colour.
CONTRAST
WARM:
You can adjust the picture contrast.
2 :lower
3 : higher
A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
BRIGHT
You can adjust the picture brightness.
2 :darker
3 : brighter
SHARP
You can adjust the picture sharpness.
2 :softer
3 : sharper
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
MAX:
FEATURES
The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL
VNR function to AUTO(HIGH) but still
notice some noise, change the setting from
AUTO(HIGH) to MAX.
Choose FEATURES and press the a or 3
button to display the sub-menu.
> FEATURES
DIGITAL VNR
Super DigiPure
MOVIE THEATRE
Colour DigiPure
COLOUR SYSTEM
4:3 AUTO ASPECT
AUTO(LOW)
AUTO
AUTO
• The MAX setting is not suitable for high-
quality pictures which contain very little
noise.
ON
„ Super DigiPure
OK
The Super DigiPure function uses the latest
in digital technology to give you a natural-
looking picture. The Super DigiPure function
includes the following two functions.
D1015-EN
• COLOUR SYSTEM cannot be chosen
when watching Digital terrestrial
broadcasting in one screen. When you are
watching Digital terrestrial broadcasting
(DVB-T) in the main picture and
Analogue terrestrial broadcasting in the
sub-picture, COLOUR SYSTEM can be
chosen for the sub picture.
DigiPure function:
This function helps to create a natural-
looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
For images with low-contrast, edges are
added to produce a sharper, more detailed
picture.
„ DIGITAL VNR
You can choose from the three DigiPure
function settings of AUTO, MIN and MAX.
• If you set the DigiPure effect too high on
a low-quality picture that contains a lot of
noise, this may actually make the noise
worse. We recommend you use the
AUTO setting if you can.
The DIGITAL VNR function cuts down the
amount of ‘noise’ (‘snow’ or interference) in
the original picture.
You can choose from the four DIGITAL
VNR function settings of AUTO(LOW),
AUTO(HIGH), MIN and MAX.
AUTO(LOW)/AUTO(HIGH):
Picture motion compensation
function:
This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.
• The effect level of the picture motion
compensation function cannot be
changed. The effect level is the same no
matter which of the AUTO, MIN or MAX
settings is used.
The TV will automatically adjust the level of
the DIGITAL VNR effect to match the
amount of noise in the picture, giving you the
best possible picture.
• If you set the DIGITAL VNR effect too
high it can make the picture less sharp. It is
recommended you use the AUTO(LOW)
setting if you can. If you set the DIGITAL
VNR function to AUTO(LOW) but still
notice some noise, change the setting from
AUTO(LOW) to AUTO(HIGH).
AUTO:
MIN:
The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.
The level of the DIGITAL VNR effect is set
to the minimum. If you set the DIGITAL
VNR function to AUTO(LOW) but feel that
the sharpness of the original picture has not
been reproduced fully, change the setting
from AUTO(LOW) to MIN.
• The MIN setting is not suitable for low-
quality pictures which contain a lot of
noise.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
MIN:
OFF:
The level of DigiPure effect is set to the
minimum. When you set the Super DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.
• The MIN setting is not suitable for high-
quality pictures which contain very little
noise.
Colour DigiPure doesn’t work. This gives a
less clear picture than when this function is
turned on.
„ COLOUR SYSTEM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
MAX:
The level of DigiPure effect is set to the
maximum. If you set the Super DigiPure
function to AUTO but feel that the original
picture quality has not been reproduced fully,
change the setting from AUTO to MAX.
• The MAX setting is not suitable for low-
quality pictures which contain a lot of
noise.
1 Choose COLOUR SYSTEM. Then
press the a or 3 button
The sub-menu of the COLOUR SYSTEM
function appears.
>> COLOUR SYSTEM
MAIN
SUB
PAL
AUTO
OFF:
The Super DigiPure function is turned off.
„ MOVIE THEATRE
OK
The MOVIE THEATRE function displays a
cinema film picture more smoothly and
naturally on the screen.
D0016-EN
2 Press the 5 buttons to choose
AUTO:
MAIN or SUB
The television automatically recognizes the
type of signal and turns the function on and
off.
MAIN:
You can change the colour system of the
main-picture.
SUB:
You can change the colour system of the
sub-picture.
• Choose MAIN when a sub-picture is
not displayed.
ON:
This function is turned on.
OFF:
This function is turned off.
• The motion may appear unnatural when
viewing images with the NTSC colour
system. When the MOVIE THEATRE
function is set to AUTO or ON, the
motion may appear unnatural when
viewing images with the NTSC colour
system.
3 Press the 6 buttons to choose
the appropriate colour system.
Then press the a button
PAL:
PAL system
NTSC 3.58:
NTSC 3.58 MHz system
NTSC 4.43:
NTSC 4.43 MHz system
„ Colour DigiPure
Makes the colour outline stand out and
increases the sharpness giving a clearer
picture.
ON:
Colour DigiPure works. Normally use with
this function turned on.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
AUTO:
This function detects a colour system
from the input signal. You can only use
this when you are viewing a picture from
programme number PR 0 (AV), or an
EXT terminal.
• The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.
• When in the Programme numbers PR 0
(AV) to PR 99, you cannot choose NTSC
3.58 or NTSC 4.43.
• “COLOUR SYSTEM” cannot be chosen
when you are watching the EXT-4
picture.
„ 4:3 AUTO ASPECT
You can choose one of three ZOOM modes,
REGULAR, PANORAMIC or 14:9 ZOOM,
as the ZOOM mode for the normal picture
(4:3 aspect ratio).
1 Choose 4:3 AUTO ASPECT then
press the a button
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
OK
D0017-EN
2 Press the 6 buttons to choose a
ZOOM mode
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND menu
SOUND
BALANCE
STEREO/
BASS
TREBLE
BALANCE
HEADPHONE VOLUME
3D CINEMA SOUND
You can adjust the volume balance between
the left and right speaker.
2 :turn the left speaker’s volume level up.
3 : turn the right speaker’s volume level up.
OK
HEADPHONE VOLUME
D0019-EN
Adjust the volume of the sub-picture sound
which is heard through the headphones when
set to 2-pictures multi.
2 :Reduce volume
3 : Increase volume
• Functions in the “SOUND” menu other
than “HEADPHONE VOLUME” work
for the TV speakers. They do not work for
the sound from the headphones.
• When the headphones are connected and
only one screen is displayed, only
“HEADPHONE VOLUME” can be used.
• STEREO / I • II cannot be chosen when
watching Digital terrestrial broadcasting
(DVB-T).
• When not set to 2-pictures multi, the
headphone volume is adjusted with the
r q (volume) buttons.
3D CINEMA SOUND
STEREO / I • II
Press the 3 button to set the 3D CINEMA
SOUND effect when 3D CINEMA SOUND
is set to ON or MONO.
When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II). If
you have poor reception on a stereo
broadcast, you can change from stereo to
mono sound so that you can hear the
broadcast more clearly and easily.
Choose 3D CINEMA SOUND. Then
press the a or 3 button to display
the sub-menu.
> 3D CINEMA SOUND
s: Stereo sound
SURROUND
BASS BOOST
MID
MID
v : mono sound
t : Bilingual I (sub I)
u : Bilingual II (sub II)
OK
D0111-EN
• The sound mode you can choose differs
depending on the TV programme.
• This function does not work in the EXT
modes.
„ SURROUND
Adjust the surround effect.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the surround
effect and choosing HIGH will increase the
surround effect.
BASS
„ BASS BOOST
You can adjust the low tone of the sound.
2 :weaker
3 : strong
Adjust the bass sound.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the bass sound
and choosing HIGH will increase the bass
sound.
TREBLE
You can adjust the high tone of the sound.
2 :weaker
3 : strong
33
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES menu
To cancel the SLEEP TIMER
function:
Press the 2 button to set the period of
time to “OFF”.
FEATURES
SLEEP TIMER
CHILD LOCK
APPEARANCE
BLUE BACK
TYPE A
ON
CHILD LOCK
OK
When there is a TV channel you do not want
your children to watch, you can use the
CHILD LOCK function to lock out the TV
channel. Even when a child chooses a
programme number (PR) for a locked TV
channel the screen will change to blue and
display n (CHILD LOCK) so the TV channel
cannot be viewed. Unless you enter a pre-set
ID number by a special operation, the lock
cannot be released and the child cannot view
the TV channel.
D0023-EN
• CHILD LOCK, APPEARANCE and
BLUE BACK cannot be chosen when
watching Digital terrestrial broadcasting
(DVB-T).
SLEEP TIMER
You can set the TV to automatically turn off
after a set period of time.
1 Choose SLEEP TIMER. Then press
the a or 3 button
„ To set the CHILD LOCK function
1 Choose CHILD LOCK, then press
the 0 button
A Sub-menu of the SLEEP TIMER
function appears.
“SET ID NO.” (ID number setting screen)
appears.
> SLEEP TIMER
0
120
> SET ID NO.
OFF
0040
OK
OK
D0024-EN
D0025-EN
2 Press the 5 buttons to set the
period of time.
2 Set the ID number to your liking
1 Press the 6 buttons to choose
a number.
Then press the a button
You can set the period of time for up to
120 minutes (2 hours) in 10 minute steps.
• One minute before the SLEEP TIMER
function turns off the TV, “GOOD
NIGHT!” appears.
• The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.
• When the SLEEP TIMER function is
on, you can display the sub-menu of
the SLEEP TIMER function again to
confirm or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to leave
the menu after confirming or changing
the remaining time.
2 Press the 5 buttons to move
the cursor.
3 Press the a button
The Sub-menu of CHILD LOCK appears.
>> CHILD LOCK
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
LOCK
OK
D0026-EK
34
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES menu
If you have forgotten the ID
4 Press the 6 buttons to choose a
TV channel
number:
Perform step 1 of “To set the CHILD
LOCK function”. After confirming the ID
number, press the TV/DTV button to exit
the menu.
Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.
• Even if you reset the lock temporarily,
it does not mean that the CHILD
LOCK function set for the TV channel
is cancelled. The next time anyone
tries to view the TV channel, it will be
locked again.
• When you want to cancel the CHILD
LOCK function, you must perform the
operation “To set the CHILD LOCK
function” again.
5 Press the blue button and set the
CHILD LOCK function.
Then press the a button
n (CHILD LOCK) appears and the TV
channel is locked.
To reset the CHILD LOCK function:
Press the blue button again.
n (CHILD LOCK) disappears.
• To stop it being easy to choose the
programme number (PR) of a locked
TV channel, the programme number
(PR) has been set so that it cannot be
chosen with the 6 buttons or the
buttons of the TV.
To disable easy resetting of the CHILD
LOCK function, the menu disappears if
you choose the CHILD LOCK function
and press the a button.
• To stop it being easy to reset the lock,
“ID NO.” (ID No. input screen) is set
so that it cannot appear unless you
„ To view a locked TV channel
1 Choose a programme number (PR)
of a locked TV channel with the
number buttons or PR LIST
The screen changes to blue and the n
(CHILD LOCK) appears. You cannot
view the TV channel.
press the
(Information) button.
h
APPEARANCE
Press the 5 button and choose the format
in which the channel number is displayed
from the three types: TYPE A, TYPE B and
TYPE C.
5
D0027-EN
2 Press the
(Information) button to
h
display “ID NO.” (ID No. input
screen)
BLUE BACK
5
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.
ID NO.
:
D0028-EN
3 Press the number buttons to enter
the ID number
ON:
This function is turned on.
The lock is temporarily released so you
can view the TV channel.
OFF:
This function is turned off.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
SET UP
EDIT/MANUAL (Analogue)
AUTO PROGRAM
EDIT/MANUAL
PICTURE TILT
DECODER(EXT-2)
EXT SETTING
The EDIT/MANUAL functions are divided
into two types:
• editing the current programme numbers
(PR) (EDIT functions); and
OFF
OFF
ATTENUATOR
• manually storing a TV channel you want
to view on a particular programme
number (PR) (MANUAL function).
OK
D0029-EN
• AUTO PROGRAM, EDIT/MANUAL,
PICTURE TILT and DECODER (EXT-2)
cannot be chosen when watching Digital
terrestrial broadcasting (DVB-T).
Here are the details about these functions:
MOVE:
This function changes the programme
number (PR) of a TV channel.
ID:
AUTO PROGRAM (Analogue)
This function registers a channel name (ID)
to a TV channel.
You can again perform the AUTO
PROGRAM function TV channel automatic
registration which was performed in the
“Initial settings” (page 8).
To receive SKY 1 you need a satellite tuner.
You must have the satellite tuner set to SKY
1 before starting the AUTO PROGRAM
function.
INSERT:
This function adds a new TV channel in the
current programme numbers (PR) list by
using the CH number.
• You cannot use the INSERT function if
you do not know the channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the programme
number (PR).
1 Choose AUTO PROGRAM, then
press the a or 3 button
The AUTO PROGRAM menu appears
and received TV channels are
automatically stored in the programme
numbers (PR).
DELETE:
This function deletes a TV channel you do
not want to list.
MANUAL:
This function manually stores a new TV
channel in a programme number (PR).
2 Perform any extra operations you
need to perform in step 3
(operations after AUTO PROGRAM
ends) and step 4 of “Initial
settings”
Caution
• Using the MOVE, DELETE or INSERT
functions rewrites the current programme
numbers (PR) list. Therefore, the
programme numbers (PR) of some of the
TV channels will change.
• Using the MANUAL function for a TV
channel for which the CHILD LOCK
function has been set cancels the CHILD
LOCK function for that channel.
• Using the MANUAL function for a TV
channel for which the DECODER (EXT-2)
function has been set to ON returns the
setting of the DECODER (EXT-2) function
for that channel to OFF.
• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes that TV channel.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
• The CH number is a number unique to
the TV and corresponds to the channel
number of a TV channel. For the
relationship between a channel number
and a CH number, see “CH
„ Basic operation
1 Choose EDIT/MANUAL, then press
the a or 3 button
The EDIT menu appears.
NUMBER” on page 40.
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
„ MOVE
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
1 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
ID
MANUAL
OK
MOVE
INSERT DELETE
D0038-EK
2 Follow the description for the
function you want to use
2 Press the 3 button to start the
MOVE function
> EDIT
3 Press the a button to complete
the settings
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
CH 21
The T-V LINK menu appears.
BBC2 CH 22
ITV
CH4
CH5
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
T-V LINK
DOWNLOAD TV
RECORDING DEVICE
OK
STORE
OK
D0030-EK
EXIT
D0005-EN
3 Press the 6 buttons to choose a
If you do not have a T-V LINK
compatible VCR connected:
Press the TV/DTV button to exit the T-V
LINK menu.
new programme number (PR)
To cancel the MOVE function:
Press the b button.
The T-V LINK menu disappears.
4 Press the 2 button to change the
programme number (PR) of a TV
channel to a new programme
number (PR)
If you have a T-V LINK compatible
VCR connected to the EXT-2 terminal:
Follow “Downloading the data to VCR” on
page 11 to transmit the programme number
(PR) data.
• For programme number PR 0, “AV”
appears in the programme numbers (PR)
list.
• An EXT terminal number does not appear
in the programme numbers (PR) list.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
„ DELETE
4 Press the blue button to display the
ID LIST (channel name list)
1 Press the 6 buttons to choose a
TV channel
> EDIT
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
CH
ID LIST
M6
MBC
MCM
MDR
MOVIE
MTV
PR
AV
01
02
03
04
05
06
07
08
09
ID
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
MTV3
M
2 Press the yellow button to delete
the TV channel
OK
D0033-EK
The TV channel is deleted from the
programme numbers (PR) list.
5 Press the 6 buttons to choose
the channel name (ID)
„ ID
To cancel the ID function:
Press the b button.
1 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
6 Press the a button to give a
channel name (ID) to a TV channel
• You can give your own unique channel
name (ID) to the TV channel. When
you have finished step 3, do not go to
step 4. Press the 5 buttons to move
to choose each character of the channel
name (ID). Then press the a button
to register the channel name (ID) to the
TV channel.
2 Press the red button to start the ID
function
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
Before performing INSERT or
MANUAL operation
ID LIST
OK
• A CH number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
D0031-EK
corresponding CH number from a table
“CH NUMBER” on page 40 based on the
Channel number of the TV channel.
3 Press the 6 buttons to choose
the first character of a channel
name (ID) you want to give the TV
channel
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
M
ID LIST
OK
D0032-EK
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
„ INSERT
„ MANUAL
1 Press the 6 buttons to choose a
programme number (PR) for which
you will register a new TV channel
1 Press the 6 buttons to choose a
programme number (PR) for a new
TV channel
2 Press the green button and start
the INSERT function
2 Press the blue button to activate
the MANUAL function
> MANUAL
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
SEARCH+
FINE-
OK
OK
0
9
FINE+
SEARCH-
D0035-EK
D0034-EN
To cancel the INSERT function:
Press the b button.
To cancel the MANUAL function:
Press the b button.
3 Press the number buttons to enter
the remaining CH number
3 Press the green or red button to
search for a TV channel
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
The TV shifts to registration mode.
When the registration is completed, the
picture of the TV channel appears on the
screen.
• The CH number is a number given to
each broadcast frequency that carries a
TV channel. If the TV cannot detect
the TV channel corresponding to the
broadcast frequency indicated by the
CH number, a “no-signal” picture
appears.
4 Press the green or red button
repeatedly until the TV channel you
want appears
If the TV channel reception is poor:
Press the blue or yellow button to fine-
tune the TV channel.
5 Press the a button and register
the TV channel to a Programme
number (PR)
The normal EDIT menu is resumed.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
„ CH NUMBER
PICTURE TILT
• When you want to use the INSERT
function on page 39, find the CH/CC
number corresponding to the channel
number of the TV channel from this table.
If you want to know a particular TV
channel’s channel menu, look in TV
listings magazines or contact the
broadcaster.
There are cases where the Earth’s magnetic
field may make the picture tilt or make
unnatural colours appear in the corner of the
screen. If this happens, you can correct it.
1 Choose PICTURE TILT, then press
the a or 3 button
The sub-menu of the PICTURE TILT
function appears.
CH
Channel
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
E40
E41
E42
E43
E44
E45
CH
Channel
E46
E47
E48
E49
E50
E51
E52
E53
E54
E55
E56
E57
E58
E59
E60
E61
E62
E63
E64
E65
E66
E67
E68
E69
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
CH 30
CH 31
CH 32
CH 33
CH 34
CH 35
CH 36
CH 37
CH 38
CH 39
CH 40
CH 41
CH 42
CH 43
CH 44
CH 45
CH 46
CH 47
CH 48
CH 49
CH 50
CH 51
CH 52
CH 53
CH 54
CH 55
CH 56
CH 57
CH 58
CH 59
CH 60
CH 61
CH 62
CH 63
CH 64
CH 65
CH 66
CH 67
CH 68
CH 69
>> PICTURE TILT
OK
D0018-EN
2 Press the 6 buttons until the
picture becomes level. Then press
the a button
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
6 Turn on the VCR, and then press
the a button to transmit the data
to recording device
DECODER (EXT-2)
If you have a decoder connected to a T-V
LINK compatible VCR, which in turn is
connected to the EXT-2 terminal, use the
DECODER (EXT-2) function to unscramble
the scrambled TV channels.
The T-V LINK menu disappears once the
data transmission ends.
7 If you have another TV channel
capable of being unscrambled with
a Decoder, repeat steps 2 to 6
1 Turn on the decoder power
2 Display the scrambled TV channel
on the TV
If the DECODER (EXT-2) function has
been set to “ON” but the TV channel
cannot be unscrambled, check the
following:
Even if the decoder is working, a
scrambled picture appears.
• Has the decoder been connected to the
VCR properly according to the VCR
and decoder instruction manuals?
• Has the decoder power been turned
on?
3 Display the SET UP menu and
choose DECODER (EXT-2)
SET UP
AUTO PROGRAM
EDIT/MANUAL
PICTURE TILT
• Can the TV channel be unscrambled
with a decoder?
DECODER(EXT-2)
EXT SETTING
ATTENUATOR
OFF
OFF
• Do you need to change the recording
device settings in order to connect the
decoder? Confirm that the VCR is set
properly by rechecking the VCR
instruction manual.
OK
D0029-EN
4 Press the 5 buttons to choose
ON
An unscrambled picture appears.
To cancel the DECODER (EXT-2)
function:
Press the 5 buttons to choose OFF.
5 Press the a button to complete
the setting
The T-V LINK menu appears.
T-V LINK
DOWNLOAD TV
RECORDING DEVICE
OK
EXIT
D0005-EN
You can send the programme numbers
data to a VCR with the T-V LINK
function.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
1 Press the 5 or 6 buttons to
EXT SETTING
choose an EXT terminal
> EXT SETTING
1 Choose EXT SETTING, then press
the a or 3 button
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
The EXT SETTING menu appears.
> EXT SETTING
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
EXT-4
DTV
ID LIST
OK
S-IN
EXT-4
D0020-EN
DTV
ID LIST
2 Press the yellow button and set the
S-IN (S-VIDEO input).
OK
S-IN
D0020-EN
Then press the a button
An S-IN (S-VIDEO input) mark is
displayed. You can view an S-VIDEO
signal (Y/C signal) instead of the regular
video signal (composite signal).
2 Follow the instructions for the
function you want to use and
operate the function
S-IN:
To cancel the S-IN (S-VIDEO input)
setting:
Press the yellow button and turn off S-IN (S-
VIDEO input) mark. The regular video
signal (composite signal) pictures are
resumed.
You can enjoy the high-quality picture of
the 2 S-VIDEO signal (Y/C signal).
ID LIST:
You can have a name for each of the
devices connected for each EXT terminal.
DUBBING:
You can choose a signal source to be
output from an EXT-2 terminal.
• The EXT-1 terminal does not support S-
VIDEO signal (Y/C signal) and you
cannot set S-IN (S-VIDEO input) in the
EXT-1 terminal.
• Setting S-IN (S-VIDEO input) changes
the head character from “E” to “S”. When
an EXT terminal receives a normal video
signal, “E2”, “E3” or “E5” appears on the
display. This changes to “S2”, “S3” or
“S5” when it receives an S-VIDEO
signal.
• Even a device which can output an
S-VIDEO signal (Y/C signal) may output
a regular video signal (composite signal)
depending on the device setting. If a
picture cannot appear because the S-IN
(S-VIDEO input) setting has been made,
read the device instruction manual
carefully again to check for the device
settings.
„ S-IN (S-VIDEO input)
You can connect a device (such as an S-VHS
VCR) to enjoy the high-quality picture of the
S-VIDEO signal (Y/C signal).
Preparation:
• First read the device’s instruction manual
and “Additional preparation” on page 53
to connect the device to the TV properly.
Second, follow the device’s instruction
manual to set the device so that it sends an
S-VIDEO signal (Y/C signal) to the TV.
• Do not set S-IN (S-VIDEO input) to an
EXT terminal connected to a device
which cannot output an S-VIDEO (Y/C
signal). If it is set wrongly, a picture
cannot appear.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
„ ID LIST
„ DUBBING
You can store a name for each of the devices
connected to each EXT terminal. Giving a
name to an EXT terminal makes the EXT
terminal number appear on the screen,
together with its name.
You can choose a signal source to be output
from the EXT-2 terminal.
You can do this with the output signals of the
devices connected to other EXT terminals, or
with the picture and sound from a TV
channel you are currently viewing.
1 Press the 5 or 6 buttons to
choose an EXT terminal
Caution:
Every time you dub, check this
DUBBING setting beforehand.
This setting may change
automatically when “Timers (DTV
Timer Recording)” or “Direct Rec” of
the T-V LINK function is used.
2 Press the blue button to display the
name list (ID LIST)
> EXT SETTING
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
ID LIST
VHS
S-VHS
DVC
CAM
SAT
1 Press the 5 buttons to choose
STB
the arrow from the menu
GAME
DVD
DVR
EXT-4
> EXT SETTING
DTV
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
OK
D0021-EN
3 Press the 6 buttons to choose a
name. Then press the a button
The ID LIST disappears and the name is
assigned to the EXT terminal.
EXT-4
DTV
OK
• You cannot assign an EXT terminal
name not found in the name list (ID
LIST).
D0022-EN
2 Press the 6 buttons to choose an
EXT terminal or TV.
To erase a name assigned to the
EXT terminal:
Choose a blank space.
Then press the a button
The arrow in the menu represents a signal
flow. The left side of the arrow shows a
signal source output from the EXT-2
terminal.
4 Press the a button to complete
the setting
EXT-1/EXT-3/EXT-5:
The output signal of the device connected
to an EXT terminal passes through the TV
and is output from the EXT-2 terminal.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
TV:
The picture and sound of the Analogue
terrestrial broadcasting TV channel you
are currently viewing are output from the
EXT-2 terminal.
DTV:
The picture and sound of the Digital
terrestrial broadcasting (DVB-T) TV
channel you are currently viewing are
output from the EXT-2 terminal.
• During dubbing, you cannot turn off
the TV. Turning off the TV also turns
off the output from the EXT-2
terminal.
• When you choose an EXT terminal as
an output, you can view a TV
programme or a picture from the other
EXT terminal while dubbing the
picture from a device connected to the
EXT terminal onto a VCR connected
to the EXT-2 terminal.
• The RGB signals from TV games
cannot be output. Teletext programmes
cannot be output.
ATTENUATOR
Turn the attenuator ON when noise is
introduced into the picture or sound due to
strong electric fields.
Normally use the TV with the attenuator
turned OFF.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
1 Choose Timers and press the a
button
DTV
Timers
Configuration
Edit PR List
Installation
The TIMER menu appears.
TIMER MENU
13:48
15/10/2003
Mode
Common Interface
No. Name
Start End
Date
D0209-EN
1
3
5
BBC ONE
BBC ONE
BBC ONE
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
• DTV in the menu bar can only be chosen
when watching Digital terrestrial
broadcasting (DVB-T).
Timers (DTV Timer Recording)
Change Mode OK Edit timer settings
More..
By setting the timer, you can record a Digital
terrestrial broadcasting (DVB-T) programme
with a VCR connected to EXT-2 or EXT-3
while you are out.
• Before using DTV timer recording, the
VCR and TV must be connected up
correctly. For details, see “Connection
when recording to VCR” on page 54.
• When you have a T-V LINK compatible
VCR connected to EXT-2, all you need to
do is set the TV timer settings and the
programme will be recorded.
D0210-EN
• When the h (Information) button is
pressed, the help screen appears. When
it is pressed again, the previous screen
is returned to.
2 Press 6 buttons to choose the
timer number, and then press the
a button
The timer setting window appears.
TIMER MENU
13:49
15/10/2003
By using “Direct Rec” of the T-V LINK
function, the Direct Rec commands are sent
from the TV to the VCR to automatically
start and end the recording. It is not
necessary to set the timer on the VCR.
• When your VCR is not T-V LINK
compatible, you also need to set the VCR
timer settings to match the TV timer
settings.
No. Name
Start End
Date
Mode
1
2
3
4
5
BBC ONE
BBC ONE
BBC ONE
BBC ONE
BBC ONE
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
00:00 00:00 01/01/2000 Inactive
Name
BBC ONE
Start
End
Date
Mode
01/01/2004
Once
Select Programme OK Confirm Timer BACKCancel
More..
D0211-EN
• The recording may not start and stop at
exactly the right times for some
programmes. It is recommended that you
allow some leeway when setting the
recording times.
• Provided that the days and times are not
the same, you can set up to five timer
settings.
buttons and a button to set the
timer
• When setting the start time and end
time, input 1200 for 12:00 PM, 1500
for 3:00 PM and 0000 for 12:00 AM.
Name:
• When subtitles are ON, the subtitles
displayed with the broadcast will be
recorded. When you do not want to record
the subtitles, you need turn OFF the
Subtitle setting beforehand (See
“Displaying the Subtitles” on page 24.).
• During DTV timer recording, you are
unable to view the SET UP menu or the
DTV menu.
Use the 5 buttons to choose the
channel for which the timer is to be set.
Press the 4 button.
Start:
Set the timer start time with the number
buttons.
• When the 5 buttons are pressed, the
input position moves.
Press the 4 button.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
End:
WARNING:
Set the timer end time with the number
buttons.
• When the 5 buttons are pressed, the
input position moves.
Do not turn off the main power. The timer
function will not work with the main
power switched off.
The TV power lamp begins flashing at three
minutes before the timer start time. When
you are watching TV at the time, a message
appears on the screen to inform you the timer
is about to start.
Press the 4 button.
Date:
Set the date for the timer to work with the
number buttons.
• When the 5 buttons are pressed, the
input position moves.
If the TV is in Standby, the power lamp
lights orange while timer recording is in
progress.
Press the 4 button.
Mode:
• When performing timer recording with a
T-V LINK compatible recording device,
test the timer recording before you record
the programme. There are some T-V
LINK compatible recording device that
will not correctly receive the Direct Rec
command from the TV.
If the recording device does not operate
when the recording start time is reached, it
is not receiving the Direct Rec command
from the TV. In this case, follow the
instructions of “When recording on a T-V
LINK incompatible VCR:”.
Use the 5 buttons to choose the timer
mode (Once/Daily/Weekly), and then
press the a button.
4 Prepare your VCR for recording
When recording on a T-V LINK
compatible VCR:
1. Insert the videotape for recording into
the VCR and set the recording mode.
2. Make sure the VCR is ready to
receive Direct Rec commands from
the TV.
• Make sure VCR timer settings do
not coincide with the TV timer
settings.
• For details, see your VCR
instruction manual.
While the timer is in operation:
• You can turn the TV on or off (Standby).
WARNING: Do not turn off the main
power.
• You can watch Analogue terrestrial
broadcasting channels or the pictures via
an EXT terminal.
• Please note that any programme
information that appears on the screen,
such as when making changes to the
Digital terrestrial broadcasting (DVB-T)
channel picture, will be superimposed
over the picture in the VCR recording.
• You cannot change Digital terrestrial
broadcasting (DVB-T) channels while
recording is in progress.
When recording on a T-V LINK
incompatible VCR:
1. Insert the videotape for recording into
the VCR and set the recording mode.
2. Set the VCR recording timer settings.
• Make the start and end time match
that of the TV timer.
• Set the VCR to record the signal
from the external input that the TV
is connected to.
• For details, see your VCR
instruction manual.
Cancelling and resetting the timer
setting:
Cancelling the timer setting
Display the TIMER MENU and press the
6 buttons to choose which timer
setting to cancel. Press the 5 buttons
so that “Inactive” appears in the Mode
column.
When you have finished Step 4, you have set
the timer.
When you are not watching TV, make sure
the TV is in standby.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
Reactivating the cancelled timer
setting
Display the TIMER MENU and press the
6 buttons to choose which timer
setting to reactivate. Press the 5
buttons so that “Active” appears in the
Mode column.
• When the b button is pressed, the
previous screen is returned to. When the
TV/DTV or H buttons are pressed,
the menu disappears.
• When the h (Information) button is
pressed, the help screen appears. When it
is pressed again, the previous screen is
returned to.
Aborting the timer recording
Display the Digital terrestrial broadcasting
(DVB-T) channel picture on the screen and
press the
(Information) button. A
h
„ Audio Language
window will appear asking if you want to
stop the recording. Press the button to
abort the recording. If you want to continue
recording, press the TV/DTV button.
With Digital terrestrial broadcasting (DVB-
T), a number of languages can be broadcast
at the same time. Choose the language you
want to listen to when watching these
broadcasts.
a
• If, while attempting to perform timer
VCR, the TV timer operation starts but
the VCR does not start recording, the
problem is related to the VCR. Resolve
the VCR-related problem and refer to
“Aborting the timer recording” to
abort the recording. After this is done,
reset the timer.
1 Press the 6 buttons and choose
Audio Language
2 Press the 5 buttons and choose
the language
The language changes every time the
button is pressed.
• If the selected language is not broadcast,
the default language will be played.
• When you are watching TV at the
recording start time, you may
encounter an error message stating that
recording could not start because of a
VCR-related problem. See “Direct
Rec” on page 12, which lists and
explains each error message.
„ Subtitle language
With Digital terrestrial broadcasting (DVB-
T), a number of subtitles can be broadcast at
the same time. Choose the subtitle you want
to display when watching these broadcasts.
1 Press the 6 buttons and choose
Configuration
Subtitle
Set the basic setting for when watching
Digital terrestrial broadcasting (DVB-T).
2 Press the 5 buttons and choose
a subtitle language that appears
when the SUBTITLE button is
pressed
Choose configuration and press the
a button
CONFIGURATION appears.
The subtitle language changes every time
the button is pressed.
CONFIGURATION
Audio Language
Subtitle
English
English
Off
„ Favourite Mode
Enable/disable the Edit PR List Favourites
settings.
Favourite Mode
Receiver Upgrade
Enter PIN code
V.3.3
1 Press the 6 buttons and choose
Favourite Mode
2 Press the 5 buttons and choose
Change preferred audio language
More..
ON or OFF
D0212-EN
47
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
On:
2 Press the 6 buttons and choose
Automatic Download, and press
the 5 buttons to choose Enable
or Disable
The Edit PR List Favourites settings are
enabled.
When the p p button is pressed, only
the channels chosen in the Edit PR List
Favourites (those with the icon) can be
chosen.
• For details on how to set your
favourite channels, see “Setting the
favourite channels” on page 51.
Enable (factory settings):
The Digital terrestrial broadcasting
(DVB-T) software is automatically
updated every day at 3:00 am. When
enabled, the TV also searches for new
software whenever it goes to standby.
Off:
Disable:
The Edit PR List Favourites settings are
disabled
When the p p button is pressed, all the
channels registered in the Edit PR List can
be chosen.
The Digital terrestrial broadcasting
(DVB-T) software is not automatically
updated.
Manually updating the Digital
terrestrial broadcasting (DVB-T)
information
„ Receiver Upgrade
Set the method to upgrade the Digital
terrestrial broadcasting (DVB-T) receiver
software.
Press the 6 buttons and choose
Search for New Version, then press
the a button
The Digital terrestrial broadcasting (DVB-T)
information is updated.
1 Press the 6 buttons and choose
Receiver Upgrade, and press the
a button
The setting window appears.
In the future, there is a possibility that the
Receiver Update function may also be able to
be used to update the Digital terrestrial
broadcasting (DVB-T) software and add new
functions.
CONFIGURATION
Audio Language
Subtitle
English
English
Off
Favourite Mode
Receiver Upgrade
Enter PIN code
V.3.3
Automatic Download
Enabled
Search for New Version
Switch automatic upgrade BACKExit submenu
More..
D0213-EN
• The actual version may be different to
the Receiver Upgrade version
displayed above.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
„ Enter PIN code
Edit PR List
Choose Enter PIN code to change the PIN
code for the Edit PR List menu’s “Lock”.
The PIN code factory setting (how it is set
when you purchase the television) is 0000.
The Edit PR List can be used to do the
following:
• delete registered channels
• edit channel names
• lock channels so that they cannot be
watched by children
1 Press the 6 buttons and choose
Enter PIN code, then press a
button
• set Favorites so that you can easily choose
from only the channels you often watch.
2 Input the current PIN code
When you are making this setting for the
first time, input 0000.
Choose Edit PR List and press the a
button
EDIT PR LIST appears.
When a PIN code has already been set,
enter the correct PIN code.
The PIN code setting window appears.
• Sometimes you may notice a drop in
picture quality while watching your
programme in the quarter-screen. This is
not a fault.
CONFIGURATION
Audio Language
Subtitle
English
English
Off
Favourite Mode
Receiver Upgrade
Menu Lock
V.3.5
EDIT PR LIST
Installation
1
BBC ONE
Enter PIN code
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
PIN code:
Confirm:
0
..
9
Enter PIN code
BACKExit PIN code menu
More..
D0225-EN
Select
Delete
Edit Name
Lock
Favourites
More..
Select function
Select PR OK Watch PR
3 Press the number buttons to input
a new PIN code (password)
D0202-EN
4 Input the new PIN code (password)
again in the Confirm box
Your newly chosen PIN code is now set.
You will now need to use the PIN code
(password) you chose here to lock or
unlock the Edit PR List’s “Lock”.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
3 Choose Yes and press the a
button
• When the b button is pressed, the
previous screen is returned to. When the
TV/DTV or H buttons are pressed,
the menu disappears.
• When the h (Information) button is
pressed, the help screen appears. When it
is pressed again, the previous screen is
returned to.
The chosen channel is deleted.
• If you do not want to delete the chosen
channel, choose No and press the a
button.
• Perform “Installation” (see page 52) to
re-register a channel that you have
deleted.
„ Choosing a channel
The chosen channel is shown on the quarter-
screen.
„ Editing a channel name
1 Press the 5 buttons and choose
Edit Name on the bar at the bottom
of the screen
1 Press the 5 buttons and choose
Select on the bar at the bottom of
the screen
2 Press the 6 buttons and choose
the channel to be edited, and then
press the a button
2 Press the 6 buttons and choose
a channel, and then press the a
button
The edit window appears.
The picture of the chosen channel is
shown on the quarter-screen.
EDIT PR LIST
2
BBC TWO
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
„ Deleting a channel
1 Press the 5 buttons and choose
Delete on the bar at the bottom of
the screen
BBC TWO
Select
Delete
Edit Name
Lock
Favourites
2 Press the 6 buttons and choose
the channel to be deleted, and then
press the a button
Select function
D0216-EN
Select PR OK Edit PR name
More..
The channel deletion confirmation
window appears.
3 Press the 6 buttons and choose
a character, press the 5 buttons
to move the cursor and edit the
name, and then press the a
button
EDIT PR LIST
2
BBC TWO
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
The selected service will be permanently
The edited channel appears in the Edit PR
List.
deleted. Are you sure?
Yes
No
Select
Delete
Edit Name
Lock
Favourites
More..
Select function
Select PR OK Delete PR
D0215-EN
50
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
When a locked channel is chosen, the
Enter PIN code input window will appear.
If the correct PIN code is input, the
picture appears.
„ Locking a channel
Digital terrestrial broadcasting (DVB-T)
channels can be locked in the same way as
the FEATURES menu CHILD LOCK.
1 Press the 5 buttons and choose
Lock on the bar at the bottom of the
screen
“Lock”, you can unlock locked
channels by performing Automatic
Search (see “Installation” on page 52).
2 Press the 6 buttons and choose
the channel to be locked, and then
press the a button
„ Setting the favourite channels
If only channels that you often watch are set
as favourite channels, you can choose from
just those channels when the p p buttons
are pressed.
The Enter PIN code input window
appears.
EDIT PR LIST
2
BBC TWO
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
WS 24
• After setting the favourite channels, check
that “Favourite Mode” in “Configuration”
Enter PIN code
1 Press the 5 buttons and choose
Favourites on the bar at the bottom
of the screen
Select
Delete
More..
0
..
9
Enter PIN code
2 Press the 6 buttons and choose
the channel to be registered as a
favourite channel, and then press
the a button
D0217-EN
3 Press the number buttons to input
the correct PIN code and press the
a button
The favourite icon appears to the right of
the chosen channel.
If you have not changed the PIN code in
the CONFIGURATION menu’s “Enter
PIN code” (see page 49), input 0000.
If you have changed the PIN code in the
CONFIGURATION menu’s “Enter PIN
code” (see page 49), input the PIN code
you chose.
LIST
The lock icon appears next to the channel
name in the Edit PR List.
D0219-EN
EDIT PR LIST
2
BBC TWO
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
Select
Delete
Edit Name
Lock
Favourites
More..
0
..
9
Enter PIN code
D0218-EN
51
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV menu
Factory Settings:
Installation
Choose when you have moved house etc
and want to automatically re-register all
the channels.
In addition to registering all the channels
that can be received, it will reset the timer
settings.
Use when re-registering a channel or when
registering a new channel.
1 Choose Installation and press the
a button
The Installation menu appears.
When Factory Settings is chosen and the
a button is pressed, the confirmation
window appears.
Installation
Automatic Search
Manual Search
Factory Settings
Are you sure you want to delete the PR list
and reset all settings?
D0220-EN
Yes
No
D0223-EN
2 Press the 6 buttons and choose
the channel registration method,
and then press the a button
To perform Factory Settings, choose Yes
and press the a button.
To cancel, choose No and press the a
button.
Automatic Search:
Choose to automatically register the
channels that can be received.
Common Interface
When Automatic Search is chosen and the
a button is pressed, the confirmation
window appears.
Choose when a pay television reception
module is inserted into the Common
Interface slot on the back of the TV, and you
want to set the module.
Start automatic search? Current PR list
will be replaced.
Yes
No
When Common Interface is chosen and the
a button is pressed, the name of the
inserted module appears. When the a
button is then pressed, the module setting
menu appears.
D0221-EN
To perform Automatic Search, choose
Yes and press the a button.
To cancel, choose No and press the a
button.
• When no module is inserted, “No CI
Module” appears.
Manual Search:
Choose to register a particular channel.
• Refer to the module instruction manual
for details of the settings.
Installation > Manual Search
Channel Number 61
Signal Level:
Signal Quality:
Move cursor
0
..
9
OK Start
More..
Enter CH number
D0222-EN
Press the number buttons and input the
channel that you want to register, and then
press the a button. The Manual Search
starts and the input channel is registered if
it can be received.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
Connecting external equipment
Connect the equipment to the TV, making
the correct rear panel and front panel
connections.
Before connecting anything:
• Read the manuals that came with the
equipment.
Depending on the equipment, the
connection method may be different from
the diagram. Also, the equipment settings
may need to change depending on the
connection method.
• Turn off all the equipment including the
TV.
• The “Specifications” on the back cover
give the details of the EXT terminals. If
you are connecting equipment not listed
in the following connection diagram, see
the table to choose the best EXT terminal.
• Connecting cables are not supplied.
• If the VCR’s audio output is in mono,
connect the VCR’s AUDIO OUT (audio
output) terminal and the TV’s EXT-5 Audio
L/MONO terminal with an audio cable.
1 VCR (composite signal)
2 VCR (composite signal/S-VIDEO signal)
3 T-V LINK compatible VCR (composite
signal/S-VIDEO signal)
4 Decoder
5 DVD player (composite signal/S-VIDEO
signal)
6 DVD player (composite signal/RGB
signal)
7 DVD player (component video signals;
Pr/Pb/Y)
8 TV game (composite signal/RGB signal)
9 TV game (composite signal/S-VIDEO
signal)
0 Headphones
- Camcorder (composite signal/S-VIDEO
signal)
= SCART cable
~ Audio cable
! Video cable
@ S-VIDEO cable
# Component cable
Side of the TV
S
R
L/MONO
EXT-5
P
S
R
L/MONO
EXT-5
P
Back of the TV
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
„ Equipment which can output the
S-VIDEO signal (Y/C signal)
Connect the equipment to an EXT terminal
(but not the EXT-1 terminal).
„ TV output from the EXT-1 terminal
The video/sound signal of a Analogue
terrestrial broadcasting channel you are
viewing is always output from the EXT-1
terminal.
You can choose between an S-VIDEO signal
(Y/C signal) and a regular video signal
(composite signal). For details of how to
operate the equipment, see “S-IN (S-VIDEO
input)” on page 42.
• Changing over a programme number (PR)
also changes over the TV output from the
EXT-1 terminal.
• The video/sound signal from an EXT
terminal cannot be output.
„ T-V LINK compatible VCR
Be sure to connect the T-V LINK compatible
VCR to the EXT-2 terminal. If not, the T-V
LINK function will not work properly.
• When connecting a T-V LINK compatible
VCR to the EXT-2 terminal, be sure to
connect the decoder to the VCR. If not,
the T-V LINK function may not work
properly. After you have stored TV
• Teletext programmes cannot be output.
„ TV output from the EXT-3 terminal
The video/sound signal of a Digital terrestrial
broadcasting (DVB-T) channel you are
viewing is always output from the EXT-3
terminal.
also changes over the TV output from the
EXT-3 terminal.
• The video/sound signal from an EXT
terminal cannot be output.
channels in the programme numbers (PR)
list, set the DECODER (EXT-2) function
for the programme number (PR) to ON to
unscramble a scrambled TV channel. For
details, see “EXT SETTING” on page 42.
VCR
„ Connecting headphones
Connect the headphones with a stereo mini-
jack (3.5 mm diameter) to the headphone
socket at the TV rear panel.
• When recording an Analogue terrestrial
broadcasting, connect to either terminal
EXT-1 or EXT-2. If you connect to the
EXT-2 terminal, make sure the
to “TV”.
• When recording a Digital terrestrial
broadcasting (DVB-T), connect to either
terminal EXT-2 or EXT-3. If you connect
to the EXT-2 terminal, make sure the
“DUBBING” setting (see page 43) is set
to “DTV”.
• Choose the EXT-2 terminal to connect to
a T-V LINK compatible VCR.
When recording an Analogue terrestrial
broadcasting, set the “DUBBING” setting
(see page 43) to “TV”.
• No sound comes from the TV speakers
when the headphones are connected and
only one screen is displayed.
„ Video or sound signal output from
the EXT-2 terminal
You can change over the output of the video/
sound signal from the EXT-2 terminal. This
is useful when you want to dub the video/
sound from another device onto the VCR
connected to the EXT-2 terminal. For details
on how to do this, see “DUBBING” on
page 43.
When recording a Digital terrestrial
broadcasting (DVB-T), set the
“DUBBING” setting (see page 43) to
“DTV”.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
„ Connecting speakers/amplifier
While referring to the audio equipment
connection diagram, connect the audio
equipment you want to the TV.
You can use external front speakers to listen
to the TV sound instead of the TV speakers.
Before connecting anything:
• Read the manuals provided with the
amplifier and speakers.
• Turn the TV and amplifier off.
• To prevent magnetism from the speakers
adversely effecting the TV screen, use
magnetic-shielded speakers for the front
speakers.
• Note that connecting cables are not
supplied.
Back of the TV
L
R
L
AUDIO OUT
R
1
2
Amplifier
Front speakers (Magnetic-shielded type)
• The output from the AUDIO OUT
terminal is not interrupted by headphone
connection to the TV. You cannot cut the
sound from the front speaker even if you
connect a headphone to the TV.
• Adjust the volume of the external
speakers with the amplifier.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Digital terrestrial broadcasting (DVB-T) service area
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial
broadcasting, depending on the area in which you live, you may not be able to receive Digital
terrestrial broadcasting (DVB-T).
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW
website etc.
If a problem arises while you are using the TV, please read this troubleshooting guide carefully
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may
think there is a problem with the TV itself.
Important:
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you
have a question when you are operating a function, read the page(s) for that function carefully,
not this troubleshooting guide.
• If you follow the advice in this troubleshooting guide without any success, unplug the mains
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to
remove the rear cover of the TV.
„ If you cannot turn on the TV
„ Poor picture
• Is the mains plug connected to the mains
outlet?
• Is the power lamp lit? If not, press the
main power button.
• If noise (snow) totally blocks out the
picture, there may be a problem with the
aerial or aerial cable. Check the following
to try to solve the problem:
–Have the TV and aerial been connected
properly?
–Has the aerial cable been damaged?
–Is the aerial pointing in the right
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV on when the VCR/TV/DVD
switch is set to the VCR or DVD position.
„ If you cannot turn off the TV
–Is the aerial itself faulty?
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV off when the VCR/TV/DVD
switch is set to the VCR or DVD position.
• If the TV or aerial suffers interference
from other equipment, stripes or noise
may appear in the picture. Move any
equipment such as an amplifier, personal
interference away from your TV. Or try
moving the TV. If the aerial suffers
interference from a radio tower or high-
voltage wire, please contact your local
dealer.
• If the TV suffers interference from signals
reflecting from mountains or buildings,
double-pictures (ghosting) will occur. Try
to change the aerial’s direction or replace
it with one with better directionality.
• Are your COLOUR SYSTEM settings
correct? Follow the description
poor reception? If so, the BLUE BACK
function will be activated: the entire
screen becomes blue, and the sound is
muted. If you still want to view the TV
channel, follow the description “BLUE
BACK” on page 35 to change the BLUE
BACK function setting to OFF.
• If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL (Analogue)” on
“COLOUR SYSTEM” on page 31 to try
to solve the trouble.
page 36 to use the MANUAL function to
try to change the SYSTEM setting.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• Have you attempted to use the remote
• Have the COLOUR and BRIGHT settings
been adjusted properly? Follow the
description “BRIGHT” and “COLOUR”
on page 29 to try to adjust them properly.
• Videotaping teletext is not recommended
because it may not record correctly.
• When a white and bright still image (such
as a white dress) is displayed on the
screen, the white part may look as if it is
coloured. This is unavoidable due to the
nature of the picture tube itself, and not
due to a TV failure. When the picture
disappears from the screen, the unnatural
colours will also disappear.
• When viewing images from commercially
available video software products, or
videos from videotapes which have been
recorded improperly, the top of the image
may be distorted. This is due to the
condition of the video signal. There is
nothing wrong with the TV.
• Since this TV is designed to make full use
source, the motion may appear unnatural
when the video source is input with 625p
progressive-scanning component signals.
If this occurs, change the output setting of
the connected device to 625i interlace-
scanning component signal output. See
the instructions that came with the device
for more information.
control from the sides or rear of the TV or
from more than seven metres away from the
TV? Use the remote control in front of your
TV or from less than seven metres away.
• When you are viewing a teletext
programme, you cannot operate the
menus. Press the b button to return to
the ordinary TV programme, and then try
operating the menus.
• If the TV suddenly stops responding,
press the main power button on the TV
and turn off the main power. Press the
main power button again to turn on the
TV. If the TV returns to a normal state, it
is not a failure.
„ Other issues
• When the SLEEP TIMER function
operates, the TV is automatically turned
off. If the TV suddenly turns off, try to
press the # (standby) button to turn on
the TV once again. If the TV goes back to
normal, there is no problem.
• When the TV is receiving a wide-screen
signal (WSS) or a signal from an external
device affecting the screen size, the
ZOOM mode automatically changes.
ZOOM mode, press the c button
again.
• If you bring magnetised equipment such
as a speaker near to your TV, the picture
may be warped or unnatural colours may
appear at the corners of the screen. In this
case, keep the equipment away from your
TV. If speakers cause this to happen, use
magnetically-shielded speakers instead.
• A picture may be tilted due to the earth’s
magnetic field. If so, use the “PICTURE
TILT” on page 40 to correct the tilt.
• It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a fault. This is the
time needed for the image to stabilize
before it can be displayed.
„ Poor sound
• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“BASS” or “TREBLE” on page 33.
be hard to hear stereo or bilingual sound.
In this case, follow the description
“STEREO / I • II” on page 33 to hear the
sound more easily by changing it to a
mono sound.
„ If the TV does not respond to the
remote control
• Have the batteries of the remote control
worn out? Follow the description “Putting
the batteries into the remote control” on
page 8 and replace them with new batteries.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• The TV may make a crackling sound due
to a sudden change in temperature. The
picture or sound may be normal. If you
hear crackling sounds frequently while
you are viewing the TV, there may be
other causes. As a precaution, ask your
service technician to inspect it.
• Touching the screen may cause you to
feel a slight electric shock due to its static
electricity. This is unavoidable due to the
construction of the picture tube. It is not a
problem with the TV. You can rest
assured that this static discharge is not
harmful.
• When set to 2-pictures multi, adjust the
headphone sound with HEADPHONE
VOLUME in the SOUND menu.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
HV-32D40BK
HV-28D40BK
Broadcasting systems
Colour systems
CCIR I
PAL
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.
Analogue: E21-E69, Digital (DVB-T): 474 MHz - 850 MHz (channel 21 - 68)
NICAM (I) system
Analogue: NICAM (I) system, Digital (DVB-T): MHEG 5 UK profile
220 - 240 V AC, 50 Hz
158 W (Standby: 2.0 W)
Viewable area 76 cm
(measured diagonally)
Channels and frequencies
Sound-multiplex systems
Teletext systems
Power requirements
Power consumption
Picture tube size
148 W (Standby: 2.0 W)
Viewable area 66 cm
(measured diagonally)
Audio output
Speakers
Rated Power output: 10 W + 10 W
(13 cm × 6.5 cm) oval × 2
EXT-1 terminal
Euroconnector (21-pin, SCART)
• Video input, Audio L/R inputs and RGB inputs are available.
• Analogue TV broadcast outputs (Video and Audio L/R) are available.
EXT-2 terminal
EXT-3 terminal
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are
available.
• Video and Audio L/R outputs are available (EXT-1, EXT-3, EXT-5, TV, DTV).
(The DTV signal is converted to analogue and then outputted.)
• T-V LINK functions are available.
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
• DTV broadcast outputs (Video and Audio L/R) are available. (The DTV signal
is converted to analogue and then outputted.)
EXT-4 terminal
EXT-5 terminal
RCA connectors × 5
• Component video (Y, Pb, Pr) inputs (625p, 525p, 625i, 525i, 1125i) and Audio
L/R inputs are available.
RCA connectors × 3
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/MONO and R inputs are
available.
CI slot
DVB Common Interface is available.
AUDIO OUT terminal
RCA connectors × 2
• Audio L/R outputs are available.
• Output level 0.5 Vrms.
Headphone jack
Dimensions (W × H × D)
Weight
Stereo mini-jack (3.5 mm in diameter)
864 mm × 587 mm × 550 mm
55.0 kg
762 mm × 528 mm × 493 mm
40.0 kg
Accessories
Remote control unit × 1 (RM-C1805)
AA/R6 dry cell battery × 2
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
LCT1596-001A-U
0404-T-CR-JMUK
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
|