WIRELESS
300N ADSL2+
MODEM ROUTER
USER MANUAL
MODELS
524780 (ANNEX A),
524797 (ANNEX B)
INT-524780/524797-UM-1109-03
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided
instructions, and a minimum of 20 cm spacing must be provided between
computer-mounted antenna and a person’s body (excluding extremities of hands,
wrists and feet) during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1) This device may not cause harmful interference; and
2) This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding these
limits, human proximity to the antenna shall not be less than 20 cm (8 inches)
Download from Www.Somanuals.com. All Manuals Search And Download.
during normal operation. The antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of Directive 1999/5/EC of the
European Parliament and the Council of March 9, 1999, on radio equipment and
telecommunication terminal Equipment and the mutual recognition of their
conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive
98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines must therefore be followed at all times to ensure the safe use of the
equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden and the United
Kingdom. The ETSI version of this device is also authorized for use in EFTA
member states: Iceland, Liechtenstein, Norway and Switzerland.
EU Countries Not Intended for Use
None.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 INTRODUCTION ..................................................................... 1
2 HARDWARE .......................................................................... 3
3 SETUP WIZARD ..................................................................... 6
3.1 Getting Started ........................................................................................... 6
3.2 Automatically Set the ISP........................................................................... 9
3.3 Manually Set the ISP................................................................................ 12
4 IP ADDRESS SETTING ..........................................................17
Windows Vista.......................................................................................... 17
Windows XP............................................................................................. 18
Windows 2000.......................................................................................... 19
5 WEB MANAGEMENT CONFIGURATION ..................................21
5.1 Quick Setup.............................................................................................. 23
5.2 General Setup .......................................................................................... 25
5.2.1 System............................................................................................... 25
5.2.1.1 Time Zone................................................................................... 25
5.2.1.2 Password Settings ...................................................................... 26
5.2.1.3 Remote Management.................................................................. 27
5.2.1.4 SNMP.......................................................................................... 29
5.2.2 WAN................................................................................................... 30
5.2.2.1 Channel Config ........................................................................... 30
5.2.2.2 ATM Setting ................................................................................ 34
5.2.2.3 ADSL Setting............................................................................... 36
5.2.2.4 DNS............................................................................................. 37
5.2.2.5 DDNS.......................................................................................... 38
5.2.2.6 RIP .............................................................................................. 39
5.2.3 LAN.................................................................................................... 41
5.2.3.1 DHCP Mode................................................................................ 43
5.2.3.2 DHCP Relay................................................................................ 43
5.2.3.3 DHCP Server .............................................................................. 44
5.2.3.4 ARP Table................................................................................... 46
5.2.3.5 Bridging....................................................................................... 46
5.2.4 Wireless ............................................................................................. 47
5.2.4.1 Basic Settings ............................................................................. 47
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.4.2 Advanced Settings ...................................................................... 49
5.2.4.3 Security ....................................................................................... 53
5.2.4.4 Access Control............................................................................ 55
5.2.4.5 WPS............................................................................................ 56
5.2.5 QoS.................................................................................................... 58
5.2.6 NAT (Network Address Translations) ................................................ 60
5.2.6.1 Port Forwarding............................................................................ 61
5.2.6.2 Port Mapping............................................................................... 62
5.2.6.3 UPNP .......................................................................................... 64
5.2.6.4 IGMP Proxy................................................................................. 65
5.2.7 Firewall............................................................................................... 66
5.2.7.1 IP/Port Filtering ........................................................................... 66
5.2.7.2 MAC Filtering .............................................................................. 68
5.2.7.3 URL Blocking .............................................................................. 70
5.2.7.4 Domain Blocking ......................................................................... 71
5.2.7.5 Routing Configuration ................................................................. 72
5.2.7.6 ACL Configuration....................................................................... 74
5.2.7.7 DMZ............................................................................................. 75
5.3 Status ....................................................................................................... 76
5.3.1 Interface............................................................................................. 77
5.3.2 ADSL ................................................................................................. 78
5.4 Tools......................................................................................................... 79
5.4.1 Configuration Tools............................................................................ 79
5.4.2 Firmware Upgrade ............................................................................. 80
5.4.3 Ping.................................................................................................... 80
5.4.4 ATM Loopback................................................................................... 81
5.4.5 Diagnostic Test.................................................................................. 82
5.4.6 Reboot ............................................................................................... 82
6 TROUBLESHOOTING ............................................................83
7 GLOSSARY ..........................................................................87
8 SPECIFICATIONS .................................................................92
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
Thank you for purchasing this INTELLINET NETWORK SOLUTIONSTM Wireless
300N ADSL2+ Modem Router, Model 524780 (Annex A) or Model 524797
(Annex B).
This is an all-in-one modem, router, Wireless N access point, firewall and Fast
Ethernet four-port switch that allows you to access the Internet and download
music, play interactive games online or surf the Web at double the speed
(depending on operating environment and distance between networked devices)
previously available through ADSL2.
Features of this router include:
• 2T2R MIMO technology for enhanced throughput and coverage
• Supports ADSL standards G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3 (ADSL2),
G.992.4 (splitterless ADSL2) and G.992.5 (ADSL2+) for Annex A
• Supports 24 Mbps ADSL2+ downstream data rate
• Supports Wi-Fi Protected Setup (WPS)
• Supports WEP and WPA/WPA2 (TKIP and AES) data encryption
• Integrated 10/100 Mbps LAN switch with Auto MDI/MDI-X support
• DHCP server assigns IP addresses for all LAN users
• DHCP server supports static lease management
• Supports virtual server, port forwarding and DMZ
• Supports DDNS (dynamic DNS)
• Supports UPnP (Universal Plug and Play)
• Integrated SPI firewall
• QoS (Quality of Service) bandwidth management
• VPN Passthrough (PPTP, IPSec, L2TP)
• Supports SNMP management
• Easy installation through Web-based user interface
• Complies with 2.4 GHz Draft IEEE 802.11n standard and is backward
compatible with IEEE 802.11g/b standards
• System status
• Security log
• Firmware upgradeable
• Three-Year Warranty
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Requirements
• A PC with pre-installed Ethernet adapter (required) and a Web browser
(Internet Explorer 4.0 or higher)
• RJ45 Ethernet crossover cable (included in the package)
• RJ11 (ADSL-ready) phone line
Package Contents
• ADSL 2+ Router (Annex A or B)
• Power adapter
• Ethernet Cat5 RJ45 cable, 1.0 m (3 ft.)
• RJ11 telephone cable, 1.8 m (5.9 ft.)
• Quick installation guide
• Setup CD with user manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Hardware
Rear Panel
Antenna A
Antenna B
Item Name
Antenna A/B
Radio
Description
These antennas are 3dBi dipole antennas.
Position the switch to activate or deactivate the wireless
functions.
ON/OFF
Reset / WPS Reset the router to factory default settings (clear all settings)
or start the WPS function. Press this button and hold for 10
seconds to restore all settings to factory defaults; press this
button for less than 5 seconds to start the WPS function.
1 - 4
The router’s 4 LAN ports are where you connect your LAN’s
PCs, printer servers, hubs and switches, etc.
Connect the supplied RJ11 telephone line to this port and
your ADSL/telephone network.
ADSL
Power
Plug the included power adapter into the power jack.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
On the router’s front panel, there are LEDs that inform you of the router’s current
status, as explained below.
LED
Status
Description
POWER (Green)
On
Router is switched on and correctly
powered.
WLAN (Yellow)
ADSL (Green)
On
Wireless LAN WPS is on.
Wireless LAN is disabled.
Wireless traffic is transmitting or
receiving.
Off
Blinking
On
Connected to an ADSL DSLAN
successfully.
Blinking
ADSL line is not connected to Internet.
The LAN cable is connected to the router.
No network connection.
LAN LNK/ACT (Port 1-4) On
Off
Network traffic transferring or receiving
through the LAN port.
Blinking
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
1. Connect the router to your ADSL cable through the supplied RJ11 cable.
2. Connect the router to your PC, hub or switch by attaching the Ethernet cable
to the LAN port of the router.
3. Connect the power adapter to the power jack on the rear panel of the router.
4. The ADSL LED will be on if the router is connected to the ADSL cable and
receives the ADSL signals successfully. If the LED is blinking, contact your
ISP (Internet service provider) to check the problem.
NOTE: Use only the power adapter included with the router, and not any other
power adapter.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Setup Wizard
This router provides a Setup Wizard tool to configure the ADSL settings. This
wizard collects some ISPs’ ADSL settings so that you can easily configure the
router’s ADSL settings by only selecting the ISP vendor from the wizard.
If you cannot find your ISP from the list in the wizard, manually set the ISP
information through the wizard.
3.1 Getting Started
Before starting, check the following items:
1. Make sure that you have connected the ADSL cable to the router correctly.
When the ADSL cable is worked normally, the ADSL LED will be on.
2. Un-install any dial-up programs installed previously for the USB modem or
other dial-up devices.
3. It is recommended that you initially configure the router through the Ethernet
cable before you set the wireless functions.
This wizard can be run in Windows 98SE/Me/2000/XP/Vista. The following
procedures are operated in Windows XP. (Procedures are similar for Windows
98SE/Me/2000/Vista.)
1. Insert the enclosed setup CD into your CD-ROM drive. The Autorun.exe
program should be executed automatically. If not, run Autorun.exe manually
from the “Autorun” folder on the CD.
2. The following screen will be displayed. Click “Setup Wizard.”
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The wizard will run and try to search for the router. If the router is
found, the wizard will guide you to Step 5.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If the router cannot be found, enter the IP address and the password of the
router to search again. Click “Next” to continue.
5. The wizard will automatically select the country you are in by checking the
language of the operating system in your computer and then advance to the
Select ISP screen. Select the ISP. If you cannot find the ISP, click “Other” to
reselect the country or manually configure the ISP information.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Automatically Set the ISP
If you can find the ISP from the wizard, follow the procedures below to let the
wizard set the ISP settings automatically.
1. Select the ISP of your ADSL service.
2. Enter the username and password that your ISP has provided to you, if
needed. Click “Next.”
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Click “Save” to save the settings and reboot the router.
4. After saving and rebooting the router, the ISP settings are completed. The
wizard will then help to set your computer to obtain an IP address from the
router automatically.
NOTE 1: To use the router to access the Internet, the IP address of each PC
needs to be set in the same network segment as the router. The wizard will help
to set the proper IP address for your computer.
NOTE 2: By default, the router’s DHCP server is enabled. If it is disabled before
running the wizard, the wizard will enable the DHCP server automatically.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The wizard will try to connect to the ISP you have selected. If the connection
fails, run the wizard to select the ISP again.
6. If you successfully connect to the ISP, you will see the screen below. To
configure additional settings, click “Advanced Settings” to go the Web
management of the router, or click “Finish” to close the wizard.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Manually Set the ISP
If you cannot find the ISP from the wizard, follow the steps below to set the ISP
settings manually.
Before configuring the ISP manually, check with your ISP (Internet service
provider) as to what kind of service is provided, such as PPPoE, PPPoA or
RFC1483/2684. Gather the information as illustrated in the following table and
keep it for reference.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password (and Service Name).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password.
RFC1483 Bridged
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged
Mode.
VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address, and Domain Name
System (DNS) IP Address (It is a fixed IP Address).
1. Select “Other.”
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Check with your ISP as to the connection type of the ADSL line. Select the
Connection Type and click “Next.”
3. Input the VPI, VCI and encapsulation data supplied by your ISP. If the
Connection Type is “Static IP Address,” you need to input the IP address
information supplied by your ISP. For details about each setting, refer to
Section 5.2.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Enter the username and password that your ISP has provided to you, if
needed. Click “Next.”
5. Click “Save” to save the settings and reboot the router.
6. After saving and rebooting the router, the ISP settings are completed. The
wizard will then help to set your computer to obtain an IP address from the
14
Download from Www.Somanuals.com. All Manuals Search And Download.
router automatically.
NOTE 1: To use the router to access the Internet, the IP address of each PC
needs to be set in the same network segment as the router. The wizard will help
to set the proper IP address for your computer.
NOTE 2: By default, the router’s DHCP server is enabled. If it is disabled before
running the wizard, the wizard will enable the DHCP server automatically.
7. The wizard will try to connect to the ISP you have selected. If the connection
fails, run the wizard to select the ISP again.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
8. If you successfully connect to the ISP, you will see the screen below. To
configure additional settings, click “Advanced Settings” to go to the Web
management of the router, or click “Finish” to close the wizard.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4 IP Address Setting
To use the router to access the Internet, the PCs in the network must have am
Ethernet adapter installed and be connected to the router either directly or
through a hub or switch. The TCP/IP protocol of each PC needs to be installed,
and the IP address of each PC has to be set in the same subnet as the router.
The router’s default IP address is 192.168.2.1 and the subnet mask is
255.255.255.0. PCs can be configured to obtain an IP address automatically
through the DHCP server of the router, or with a fixed IP address in order to be in
the same subnet as the router. By default, the DHCP server of the router is
enabled and will dispatch an IP address to the PC in the range of 192.168.2.100
to 192.168.2.200. It is strongly recommended that you obtain the IP address
automatically.
This section shows you how to configure your PC so that it can obtain an IP
address automatically for Windows 95/98/Me, 2000 or NT operating systems. For
other operating systems (Macintosh, Sun, etc.), follow the manual of the
operating systems. The following are step-by-step procedures for configuring
your PC to obtain an IP address automatically for Windows Vista, Windows XP
and Windows 2000.
Windows Vista
1. Click “Start” and select “Settings,” then select “Control Panel.” Double-click
“Network and Sharing Center”; the Network and Sharing Center window will
appear.
2. Click “Manage network connections”; right-click on the Local Area Connection
icon and select “Properties.” The Local Area Connection window will appear.
3. Check your list of Network Components. You should see “Internet Protocol
Version 4 (TCP/IPv4)” on your list. Select it and click “Properties.”
4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select
“Obtain an IP address automatically” and “Obtain DNS server address
automatically,” as shown on the following screen.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click “OK” to confirm the setting. Your PC will now obtain an IP address
automatically from your router’s DHCP server.
NOTE: Make sure that the router’s DHCP server is the only DHCP server
available on your LAN.
Windows XP
1. Click “Start” and select “Control Panel”; then double-click “Network
Connections.” The Network Connections window will appear.
2. Right-click on the Local Area Connection icon and select “Properties.” The
Local Area Connection window will appear.
3. Check your list of Network Components. You should see “Internet Protocol
[TCP/IP]” on your list. Select it and click “Properties.”
4. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP
address automatically” and “Obtain DNS server address automatically,” as
shown on the following screen.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click “OK” to confirm the setting. Your PC will now obtain an IP address
automatically from your router’s DHCP server.
NOTE: Make sure that the router’s DHCP server is the only DHCP server
available on your LAN.
Windows 2000
1. Click “Start” and select “Settings,” then click “Control Panel.” The Control
Panel window will appear.
2. Double-click the Network and Dial-up Connections icon. In the Network and
Dial-up Connection window, double-click the Local Area Connection icon. The
Local Area Connection window will appear.
3. In the Local Area Connection window, click “Properties.”
4. Check your list of Network Components. You should see “Internet Protocol
[TCP/IP]” on your list. Select it and click “Properties.”
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP
address automatically” and “Obtain DNS server address automatically,” as
shown on the following screen.
6. Click “OK” to confirm the setting. Your PC will now obtain an IP address
automatically from your router’s DHCP server.
NOTE: Make sure that the router’s DHCP server is the only DHCP server
available on your LAN.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Web Management Configuration
Once you have configured your PCs to obtain an IP address automatically, the
router’s DHCP server will automatically give your LAN clients an IP address. By
default, the router’s DHCP server is enabled so you can obtain an IP address
automatically.
Once your PC has obtained an IP address from your router, enter the default IP
address 192.168.2.1 (router’s IP address) into your PC’s Web browser and press
<Enter> on your keyboard.
The login screen below will appear. Fill in the “User Name” and “Password” text
fields, then click “OK” to log in. By default, the username is “admin” and the
password is “1234.” For security reasons, it is recommended that you change the
password as soon as possible.
The HOME screen screen below will appear. The Home Screen is divided into
four sections: Quick Setup, General Setup, Status, Tools.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup (Section 5.1)
The Quick Setup Wizard provides only the necessary configurations to connect
your router to your Internet service provider (ISP).
General Setup (Section 5.2)
The router supports advanced functions like virtual server, access control, hacker
attack detection and DMZ. It’s highly recommended that you keep the default
settings.
Status (Section 5.3)
The status section provides the following information about your router:
hardware/firmware version, serial number and its current operating status.
Tools (Section 5.4)
Tools include configuration tools, firmware upgrading and reset configuration
tools that allow you to back up, restore or restore to factory default settings.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Quick Setup
The Quick Setup section is designed to get you using the router as quickly as
possible. Before configuring the router, check with your ISP (Internet service
provider) as to what kind of the service is provided, such as PPPoE, PPPoA or
RFC1483/2684. Gather the information as illustrated in the table below and keep
it for reference.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password (and Service Name).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password.
RFC1483 Bridged
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged
Mode.
VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address, and Domain Name
System (DNS) IP Address (It is a fixed IP Address).
1. Click “Quick Setup” and the following screen will be displayed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select the country you’re in and your ISP (Internet service provider).
3. Enter the username and password your ISP has provided to you, if needed.
Click “Finish” to save the settings.
4. Click “Commit and Reboot” to reboot the router.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 General Setup
Start your Web browser and log on to the Web management interface of the
router, then either click “General Setup” on the left menu or click the “General
Setup” link at the upper-right corner of the Web management interface.
5.2.1 System
This screen includes the basic configuration tools for the router’s remote
management access function.
5.2.1.1 Time Zone
Time Zone allows your router to set its time, especially useful when recording
System Log entries.
Parameter
Description
Current Time
The current time of the specified time zone. You can set
the current time yourself or configure it via SNTP server.
Select the time zone of the country you are in. The router
will set its time based on your selection.
Check the box to enable the router to update time from
the SNTP server.
Time Zone Select
Enable SNTP client
update
SNTP server
The IP address or the host name of the SNTP server.
You can select from the list or set it manually.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings and restart the router so the settings
will take effect after it reboots.
5.2.1.2 Password Settings
This screen allows you to set the password to access the Web server of the
router. Select the “admin” (as administrator) or “user” (as user) account and
configure the password.
When you finish, click “Apply Changes.”
If the passwords you entered in the “New Password” and “Confirmed Password”
fields are not the same, you’ll see the following message:
Re-enter the new password again when you see above message.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
If you see the following message:
It means the content in the “Current Password” field is wrong. Click “OK” to go
back to the previous menu and input the current password again.
If the current and new passwords are correctly entered, after you click “Apply”
you’ll be prompted to input your new password:
Use the new password to enter the Web management interface again, and you
should be able to log in with the new password.
5.2.1.3 Remote Management
The Remote Access function can secure remote host access to your router from
LAN and WAN interfaces for some services provided by the router. These
services include Telnet, FTP, TFTP, HTTP, SNMP and PING.
Click the “System” menu on the left of the Web management interface, then click
“Remote Management” and the following screen will be displayed on your Web
browser.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
LAN
Check/un-check the services on the LAN column to allow/
disallow the services access from the LAN side.
Check/un-check the services on the WAN column to allow/
disallow the services access from the WAN side.
This field allows the user to specify the port corresponding to
the service. Take the HTTP service, for example: When it is
changed to 8080, the HTTP server address for the WAN side
is http://dsl_addr:8080, where “dsl addr” is the WAN-side IP
address of the router.
WAN
WAN Port
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.1.4 SNMP
Simple Network Management Protocol (SNMP) is a troubleshooting and
management protocol that uses the UDP protocol on Port 161 to communicate
between clients and servers. The router can be managed locally or remotely by
SNMP protocol.
Parameter
Description
SNMP
Select “Disable” or “Enable” to disable or enable the
SNMP feature.
System Description
System Contact
Enter the system description of the router.
Enter the contact person and/or contact information for
the router.
System Name
Assign an administrative name for the router.
The physical location of the router.
This is the vendor object identifier: the vendor’s
authoritative identification of the network management
subsystem contained in the entity.
Destination IP address of the SNMP trap.
Name of the read-only community. This read-only
community allows read operation to all objects in the
MIB.
System Location
System Object ID
Trap IP Address
Community name
(read-only)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Community name
(write-only)
Name of the write-only community. This write-only
community allows write operation to the objects defines
as read-writable in the MIB.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2 WAN
Use the WAN Settings screen if you have already configured the Quick Setup
Wizard section and you would like to change your Internet connection type. The
WAN Settings screen allows you to specify the type of WAN port connection you
want to establish with your ISP. The WAN settings offer the following selections
for the router’s WAN port: Channel, ATM Setting, ADSL Setting, DNS, DDNS and
RIP.
5.2.2.1 Channel Config
The router supports eight ATM permanent virtual channels (PVCs) at the most.
This screen is used to configure the parameters for the channel operation modes
of your router. Before configuring the router, check with your ISP as to what kind
of service is provided, such as PPPoE, PPPoA or RFC1483/2684. Gather the
information as illustrated in the table below and keep it for reference.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password (and Service Name).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username,
Password.
RFC1483 Bridged
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged
Mode.
VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address, and Domain Name
System (DNS) IP Address (It is a fixed IP Address).
VPI/VCI, VC-based/LLC-based multiplexing, IP Address,
Subnet Mask, Gateway Address, and Domain Name
System (DNS) IP Address.
RFC1483 MER
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
VPI
VPI is a virtual path that determines the way an ATM cell
should be routed. The VPI is an 8-bit (in UNI) or 12-bit (in
NNI) number that is included in the header of an ATM
cell. The valid range for the VPI is 0 to 255. Enter the VPI
assigned by the ISP.
VCI
VCI is the label given to an ATM VC to identify it and
determine its destination. The VCI is a 16-bit number that
is included in the header of an ATM cell. The valid VCI
range is 32 to 65535. Enter the VCI assigned by the ISP.
Check with your ISP for the method of multiplexing.
There are five kinds of channel modes you can select for
an ADSL connection. Check with your ISP for the method
of the ADSL connection.
Encapsulation
Channel Mode
Enable NAPT
Enable or disable NAPT, an Internet standard that
enables a local-area network (LAN) to use one set of IP
addresses for internal traffic and a second set of
addresses for external traffic. When NAPT is enabled,
the router will help to make all necessary IP address
translations for the PC connected to the router to access
the Internet.
Admin Status
User Name
Password
Type
Enable or disable the PVC channel setting.
Enter the username exactly as your ISP assigned it.
Enter the password that your ISP has assigned to you.
Continuous – The connection will be kept always on. If
the connection is interrupted, the router will re-connect
automatically.
Connect on Demand – Only connects when you want to
surf the Internet. “Idle Time” is set to stop the connection
when the network traffic is not sending or receiving after
an idle time.
Manual – After you have selected this option, go to the
Status screen and click “Connect.” The router will
connect to the ISP. If you want to stop the connection,
click “Disconnect.”
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Idle Time (ms)
Type
“Idle Time” is set to stop the connection when the
network traffic is not sending or receiving after an idle
time.
Fixed IP – Set the static IP Address to the router. Enter
the IP address your ISP has assigned.
DHCP – To get the IP address from the ISP directly.
Set the IP address obtained from your ISP.
Enter the remote IP address assigned by your ISP.
Enter the subnet mask assigned by your ISP.
The IP Unnumbered configuration allows you to enable
IP processing on a serial interface without assigning it an
explicit IP address. When it is enabled, the router’s WAN
IP address can “borrow” the IP address of another
interface already configured on the router, which
conserves network and address space. Check it if you
want to assign the WAN IP address from other interface,
such as a client’s IP address.
Local IP Address
Remote IP Address
Subnet Mask
Unnumbered
Default Route
Add/Modify
When “Default Router” is enabled, all the packets for
destinations not known by the router’s routing table are
sent to the default route. By default, it is enabled.
These buttons are for you to maintain the channel
configuration settings.
Current ATM VC Table The channel you have configured will be listed here. You
can select the VC channel to Edit or Delete.
Delete Selected
If you want to delete a specific VC channel entry, check
the “select” box of the VC channel you want to delete,
then click “Delete Selected.”
Enable Auto-PVC
Search
Check the box and click “Apply” to enable the auto PVC
search function.
VPI
VPI is a virtual path that determines the way an ATM cell
should be routed.
VCI
VCI is the label given to an ATM VC to identify it and
determine its destination.
Add/Delete
These buttons are for you to maintain the Current Auto-
PVC Table.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2.2 ATM Setting
The screen is for ATM PVC QoS parameters setting.
Parameter
Description
VPI
VPI is a virtual path that determines the way an ATM cell
should be routed. The VPI is an 8-bit (in UNI) or 12-bit (in
NNI) number that is included in the header of an ATM
cell. The valid range for the VPI is 0 to 255. Enter the VPI
assigned by the ISP.
VCI
VCI is the label given to an ATM VC to identify it and
determine its destination. The VCI is a 16-bit number that
34
Download from Www.Somanuals.com. All Manuals Search And Download.
is included in the header of an ATM cell. The valid VCI
range is 32 to 65535. Enter the VCI assigned by the ISP.
UBR (Unspecified Bit Rate) – Select UBR for applications
that are non-time sensitive, such as e-mail.
QoS
CBR (Constant Bit Rate) – This class is used for
emulating circuit switching. The cell rate is constant with
time. Select CBR to specify fixed (always on) bandwidth
for voice or data traffic.
nrtVBR (non-real time Variable Bit Rate) – This class
allows users to send traffic at a rate that varies with time
depending on the availability of user information.
Statistical multiplexing is provided to make optimum use
of network resources. Multimedia e-mail is an example of
nrtVBR.
rtVBR (real time Variable Bit Rate) – This class is similar
to nrtVBR but is designed for applications that are
sensitive to cell-delay variation. Examples for real-time
VBR are voice with speech activity detection (SAD) and
interactive compressed video.
PCR
Divide the DSL line rate (bps) by 424 (the size of an ATM
cell) to find the PCR (Peak Cell Rate). This is the
maximum rate at which the sender can send cells.
PCR generally is coupled with the CDVT (Cell Delay
Variation Tolerance), which indicates how much jitter is
allowable.
CDVT
SCR
MBS
SCR (Sustain Cell Rate) is the average rate over a long
interval, in the order of the connection lifetime.
MBS (Maximum Burst Size) refers to the maximum
number of cells that can be sent at the peak rate. Enter
the MBS, which is less than 65535.
Current ATM VC Table The channel you have configured with regard to the ATM
settings will be listed here.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2.3 ADSL Setting
The screen allows you to select any combination of DSL modes.
Parameter
Description
ADSL modulation
AnnexL Option
AnnexM Option
ADSL Capability
Choose preferred ADSL standard protocols.
Enable/Disable ADSL2/ADSL2+ Annex L capability.
Enable/Disable ADSL2/ADSL2+ Annex M capability.
Bitswap Enable – Enable/Disable bitswap capability.
SRA Enable – Enable/Disable SRA (seamless rate
adaptation) capability.
ADSL Tone
Choose tones to be masked. The masked tones will not
36
Download from Www.Somanuals.com. All Manuals Search And Download.
carry any data. Click “Tone Mask” to mask the tone
number you have selected or all the tone numbers.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2.4 DNS
A Domain Name System (DNS) server is like an index of IP addresses and Web
addresses. If you type a Web address into your browser, such as
“www.router.com,” a DNS server will find that name in its index and the matching
IP address. This screen is used to select the way to obtain the IP addresses of
the DNS servers.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Attain DNS
Select this item if you want to use the DNS servers
obtained from ISP.
Automatically
Set DNS Manually
Select this item to specify up to three DNS IP addresses.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2.5 DDNS
Dynamic DNS (DDNS) allows you to map the static domain name to a dynamic
IP address. You must get an account, password and your static domain name
from the DDNS service providers.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Enable
Description
Check the box to enable DDNS function.
Select your DDNS service provider here. This router
supports DynDNS and TZO service providers.
Enter the domain name you’ve obtained from the DDNS
service provider.
DDNS Provider
Host Name
Username
Password
E-mail
Enter the username assigned by the DDNS service
provider.
Enter the password assigned by the DDNS service
provider.
Enter the e-mail account that your DDNS service
provider assigned to you.
Key
Enter the password that your DDNS service provider
assigned to you.
Add/Modify/Remove
These buttons are for you to maintain the DDNS table.
Dynamic DDNS Table The DDNS you have configured will be added to the list.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.2.6 RIP
RIP is an Internet protocol you can set up to share routing-table information with
other routing devices on your LAN, at your ISP’s location, or on remote networks
connected to your network via the ADSL line.
Most small home or office networks do not need to use RIP; they have only one
router, such as this one, and one path to an ISP. In these cases, there is no need
39
Download from Www.Somanuals.com. All Manuals Search And Download.
to share routes because all Internet data from the network is sent to the same
ISP gateway.
You may want to configure RIP if any of the following circumstances apply to
your network:
• Your home network setup includes an additional router or RIP-enabled PC
(other than this one). This router and the other router will need to communicate
via RIP to share their routing tables.
• Your network connects via the ADSL line to a remote network, such as a
corporate network. In order for your LAN to learn the routes used within your
corporate network, they should both be configured with RIP.
• Your ISP requests that you run RIP for communication with devices on their
network.
Parameter
RIP
Description
Enable/disable the RIP feature.
Select the interface that you want to enable the RIP
Interface
feature.
Indicate the RIP version in which information must be
passed to the DSL device in order for it to be accepted
into its routing table.
Receive Mode
Send Mode
Indicate the RIP version this interface will use when it
sends its route information to other devices.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
RIP Config Table
The RIP you have configured will be listed in the table. If
you want to delete some settings, select the settings and
click “Delete Selected.”
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.3 LAN
This screen is used to configure the LAN interface of this router. You can set IP
address, subnet mask and IGMP Snooping.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Interface Name The interface name is “br0.”
IP Address
Enter the IP address of the ADSL router for the local user to
access the router’s Web screen. By default, the IP address is
192.168.2.1.
Subnet Mask
Secondary IP
Enter the subnet mask of the ADSL router. By default, the
subnet mask is 255.255.255.0.
Assign a second IP address to the LAN.
IGMP Snooping Enable/disable the IGMP snooping function for the multiple
bridged LAN ports. When “IGMP Snoop” (Internet Group
Management Protocol Snoop) is enabled, the router can make
intelligent multicast forwarding decisions by examining the
contents of each frame’s IP header. Without the function, the
router will broadcast the multicast packets to each port and
may create excessive traffic on the network and degrade the
performance of the network.
Ethernet to
Wireless
Blocking
Enable/disable the “Ethernet to Wireless Blocking.” When this
function is enabled, the traffic between Ethernet and wireless
interfaces is not allowed.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.3.1 DHCP Mode
You can configure your network and the router to use the Dynamic Host
Configuration Protocol (DHCP). This screen allows you to select the DHCP mode
that this router will support.
There are two different DHCP modes: DHCP Server and DHCP Relay. When the
router is acting as a DHCP server, configure it on the DHCP Server screen; while
acting as a DHCP relay, you can set up the relay on the DHCP Relay screen.
5.2.3.2 DHCP Relay
Some ISPs perform the DHCP server function for their customers’ home/small
office network. In this case, you can configure this device to act as a DHCP relay
agent. When a user’s computer on your network requests Internet access, the
router contacts your ISP to obtain the IP configuration, and then forwards that
information to the computer.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
DHCP Server Address Specify the IP address of your ISP’s DHCP server.
Requests for IP information from your LAN interface will
be passed to the default gateway, which should route the
request appropriately.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.3.3 DHCP Server
When the DHCP server is enabled, the router will automatically give your LAN
clients an IP address. If the DHCP is not enabled, then you’ll need to manually
set your LAN clients’ IP addresses.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
LAN IP Address
Subnet Mask
IP Pool Range
The current IP address of the router.
The current subnet mask of the router.
You can select a particular IP address range for your
DHCP server to issue IP addresses to your LAN clients.
By default, the IP range is from 192.168.2.100 to
192.168.2.200.
Show Client
Click and a table is displayed, presenting the assigned IP
address, MAC address and time expired for each DHCP
leased client.
Subnet Mask
Enter the subnet mask for LAN clients.
Max Lease Time
In the Lease Time setting, you can specify the time
period that the DHCP server lends an IP address to your
LAN clients. The DHCP will change your LAN clients’ IP
address when this time threshold period is terminated.
A user-friendly name that refers to the group of hosts
(subnet) that will be assigned addresses from this pool.
The IP address of the router.
Domain Name
Gateway Address
MAC Base Assignment Click and you can assign a static IP address to the
computer with the designated MAC address. The MAC
address is the 12-digit hexadecimal number; for example,
“00-d0-59-c6-12-43.” The assigned IP address should be
a unique IP address.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.3.4 ARP Table
ARP is the Address Resolution Protocol. Its job is to match MAC addresses to IP
addresses and vice versa (matching IP addresses to MAC addresses). This
screen lists the IP addresses and the matched MAC addresses in the network.
5.2.3.5 Bridging
You can enable/disable the Spanning Tree Protocol and set the MAC address
aging time on this screen.
Parameter
Description
Aging Time
Set the Ethernet address ageing time. After the aging
time of not having seen a frame coming from a certain
address, the bridge will time out (delete) and not forward
the frame.
802.1d Spanning Tree Enable/disable the Spanning Tree Protocol. When this
feature is enabled, this router will use the Spanning Tree
Protocol to prevent a network loop from forming in the
network (LAN side).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.4 Wireless
The router builds a wireless LAN and can let all IEEE 802.11b, IEEE 801.11g or
IEEE 802.1n wireless stations connect to your intranet. It supports WEP, WPA
and WPA2 encryption to enhance the security of your wireless network. It also
supports WPS so you can easily set up the wireless connection between the
router and other stations.
5.2.4.1 Basic Settings
This section provides the wireless network settings for your router. You can
enable the wireless AP function here.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Disable Wireless LAN Check to deactivate the wireless function of the router.
Interface
Band
When this is activated, the router will not be an access
point for other wireless clients to connect wirelessly.
Select the radio band from one of the following options:
• 2.4GHz(B): only allows 802.11b wireless network
clients to connect to this router (maximum transfer rate
is 11 Mbps).
• 2.4 GHz (G): only allows 802.11g wireless network
clients to connect to this router (maximum transfer rate
is 54 Mbps).
• 2.4 GHz (B+G): only allows 802.11b and 802.11g
wireless network clients to connect to this router
(maximum transfer rate is 11 Mbps for 802.11b clients;
54 Mbps for 802.11g clients).
• 2.4 GHz (N): only allows 802.11n wireless network
clients to connect to this router (maximum transfer rate
is 150 Mbps).
• 2.4 GHz (G+N): only allows 802.11g and 802.11n
wireless network clients to connect to this router
(maximum transfer rate is 54 Mbps for 802.11g clients;
150 Mbps for 802.11n clients).
• 2.4 GHz (B+G+N): allows 802.11b, 802.11g and
802.11n wireless network clients to connect to this
router (maximum transfer rate is 11 Mbps for 802.11b
clients; 54 Mbps for 802.11g clients; 150 Mbps for
802.11n clients).
Mode
SSID
Set the router to act in AP, Client or WDS mode.
The SSID (up to 32 printable ASCII characters) is the
unique name identified in a WLAN. The ID prevents the
unintentional merging of two co-located WLANs. The
default SSID of the router is “default.”
Channel Width
Sets the channel width of the wireless radio. Do not
modify the default value if you don’t know what it is. The
default setting is “Auto 20/40 MHz.”
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Sideband
Channel Number
Select the upper band or lower band for your radio
frequency. While “Upper” is selected, the channel options
are from 5 to 11. While “Lower” is selected, the channel
options are from 1 to 7.
This is the radio channel used by the wireless LAN. All
devices in the same wireless LAN should use the same
channel. Select the country and designate a channel that
the router will use. To let the router automatically find an
available channel with the highest signal strength, select
“Auto.”
Radio Power (mW)
Associated Clients
Sets the maximum output power of the router. The higher
the output power, the wider the coverage range.
Click to see the wireless clients connected to the router.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.4.2 Advanced Settings
This screen allows advanced users who have sufficient knowledge of wireless
LANs to make configuration changes. These settings shouldn’t be changed
unless you know exactly what will happen as a result.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Authentication Type
There are three authentication types: Open System,
Shared Key and Auto.
• Open System authentication is not required to be
successful, as a client may decline to authenticate with
any other particular client.
• Shared Key is only available if the WEP option is
implemented. Shared Key authentication supports
authentication of clients as either a member of those
who know a shared secret key or a member of those
who do not. IEEE 802.11 Shared Key authentication
accomplishes this without the need to transmit the
secret key in clear. Requires the use of the WEP
privacy mechanism.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
• Auto is the default authentication algorithm. It will
change its authentication type automatically to fulfill a
client’s requirement.
Fragmentation
Threshold
Fragment Threshold specifies the maximum size of a
packet during the fragmentation of data to be transmitted.
If you set this value too low, it will result in bad
performance. Enter a value from 256 to 2346.
RTS Threshold
This value should remain at its default setting of 2347.
Should you encounter inconsistent data flow, only minor
modifications are recommended. If a network packet is
smaller than the preset “RTS Threshold” size, the
RTS/CTS mechanism will not be enabled. The wireless
router sends Request to Send (RTS) frames to a
particular receiving station and negotiates the sending of
a data frame. After receiving an RTS, the wireless station
responds with a Clear to Send (CTS) frame to
acknowledge the right to begin transmission.
Beacon Interval
Data Rate
This is the interval of time that this wireless router
broadcasts a beacon, which is used to synchronize the
wireless network. The range for the beacon period is 20
to 1024, with a default value of 100 (milliseconds).
This setting depends on the speed of your wireless
network. You should select from a range of transmission
speeds, or you can select “Auto” to have the wireless
router automatically use the fastest possible data rate
and enable the Auto-Fallback feature, which negotiates
the best possible connection speed between the router
and a wireless client. The default setting is “Auto.”
This defines the length of the CRC (Cyclic Redundancy
Check) block for communication between the router and
wireless stations. Make sure to select the appropriate
preamble type. Note that high network traffic areas
should use “Short Preamble.” CRC is a common
technique for detecting data transmission errors.
If this option is enabled, the router will automatically
Preamble Type
Broadcast SSID
51
Download from Www.Somanuals.com. All Manuals Search And Download.
transmit the network name (SSID) into open air at regular
intervals. This feature is intended to allow clients to
dynamically discover the router. If this option is disabled,
the router will hide its SSID. When this is done, the
clients cannot directly discover the router and MUST be
configured with the SSID for access to the router. It is
used to protect your network from being accessed easily.
When you enable this function, wireless clients will not be
able to directly access other wireless clients.
Relay Blocking
Protection
This is also called CTS Protection. It is recommended to
enable the protection mechanism. This mechanism can
decrease the rate of data collision between 802.11b and
802.11g/802.11n wireless stations. When the protection
mode is enabled, the throughput of the AP will be a little
lower.
Aggregation
Short GI
This is used to join multiple data packets for transmission
as a single unit to increase network efficiency.
The 802.11n draft specifies two guard intervals: 400 ns
(short) and 800 ns (long). Support of the 400 ns GI is
optional for transmit and receive. Enabling this function
will increase network efficiency.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.4.3 Security
This router provides complete wireless LAN security functions, including WEP,
IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA with
RADIUS. With these security functions, you can protect your wireless LAN from
illegal access. Make sure your wireless stations use the same security function.
Parameter
Description
Encryption
Choose “None” to disable the encryption, or select
“WEP,” “WPA(TKIP),” “WPA2(AES)” or “WPA2 Mixed”
mode for security. When “WEP” is enabled, click “Set
WEP Key” to choose the default key and set the four sets
of WEP keys.
• WEP is a lower level of security than WPA, and
supports 64-bit and 128-bit key lengths to encrypt the
wireless data.
• WPA (TKIP) uses Temporal Key Integrity Protocol
(TKIP) for data encryption. TKIP utilizes a stronger
encryption method and incorporates Message Integrity
Code (MIC) to provide protection against hackers.
• WPA2 (AES) uses the Advanced Encryption Standard
(AES) for data encryption, which utilizes a symmetric
128-bit block data encryption.
• WPA Mixed tells the router to support WPA (TKIP) and
53
Download from Www.Somanuals.com. All Manuals Search And Download.
WPA2 (AES) for data encryption. The actual selection
of the encryption methods will depend on the clients.
IEEE 802.1x is an authentication protocol. Every user
must use a valid account to log in to this wireless router
before accessing the wireless LAN. The authentication is
processed by a RADIUS server. Check this box to
authenticate a user by IEEE 802.1x.
Use 802.1x
Authentication
WEP-64Bits
WEP is a lower level of security than WPA, and supports
64-bit and 128-bit key lengths to encrypt the wireless
data. The longer key length will provide higher security.
When “WEP-64Bits” is selected, you need to enter
exactly 5 ASCII characters (“a-z” and “0-9”) or 10
hexadecimal digits (“0-9,” “a-f”) for each Key (1-4).
When “WEP-128Bits” is selected, you need to enter
exactly 13 ASCII characters (“a-z” and “0-9”) or 26
hexadecimal digits (“0-9,” “a-f”) for each Key (1-4).
There are two types of authentication mode for WPA.
• Enterprise (RADIUS) uses an external RADIUS server
to perform user authentication. To use RADIUS, enter
the IP address of the RADIUS server, the RADIUS port
(default is 1812) and the shared secret from the
RADIUS server. Refer to the “Authentication RADIUS
Server” setting below for RADIUS setting.
WEP-128Bits
WPA Authentication
Mode
• Personal (Pre-Shared Key) authentication is based on a
shared secret that is known only by the parties involved.
To use WPA Pre-Shared Key, select the key format and
enter a password in the “Pre-Shared Key Format” and
“Pre-Shared Key” settings.
Pre-Shared Key
Format
You can select Passphrase (alphanumeric format) or
Hexadecimal Digits (in the “A-F,” “a-f” and “0-9” range) to
be the Pre-shared Key. For example:
Passphrase: ”iamguest”
Hexadecimal Digits: “12345abcde”
Pre-Shared Key
Authentication
Enter 8-63 characters as the “Pre-Shared Key.”
Enter the port (default is 1812), the IP address and the
54
Download from Www.Somanuals.com. All Manuals Search And Download.
RADIUS Server
password of the external RADIUS server.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.4.4 Access Control
This wireless router provides MAC Address Control, which prevents unauthorized
MAC addresses from accessing your wireless network.
Parameter
Description
Wireless Access
Control Mode
This router can prevent wireless clients from accessing
the wireless network by checking the MAC address of the
55
Download from Www.Somanuals.com. All Manuals Search And Download.
clients. If you enable this function, set the MAC address
of the wireless clients that you want to filter.
Disable disables this function.
Allow Listed only allows the wireless clients with the MAC
address you have specified access to the router.
Deny Listed means the wireless clients with the MAC
address you have specified will be denied access to the
router.
MAC Address
Enter the MAC address of the wireless clients for the
filtering control.
Current Access Control To remove a MAC address from the Current Access
List
Control List, select it and click “Delete Selected.” To
remove all MAC addresses from the table, just click
“Delete All.” Click “Reset” to clear your current selections.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.4.5 WPS
Although home Wi-Fi networks have become more and more popular, users still
have trouble with the initial setup of a network. This obstacle forces users to use
an open security setting and increases the risk of eavesdropping. Wi-Fi Protected
Setup (WPS) was designed to make it easier to set up security-enabled Wi-Fi
networks and, subsequently, network management.
The biggest difference between WPS-enabled devices and legacy devices is that
users do not need to know about SSID or channel and security settings, but they
could still surf in a security-enabled Wi-Fi Network. This device supports both the
Push Button and PIN methods for WPS, as described below.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Disable WPS
WPS Status
Check to disable Wi-Fi Protected Setup.
When the settings are factory defaults (out of the box), it
is set to an open security and unconfigured state. “WPS
Status” will display it as “UnConfigured.” If it already
shows “Configured,” some registrars such as Vista WCN
will not configure the router, and you’ll need to go to the
Backup/Restore screen and click “Reset” to reload the
factory default settings.
Self-PIN Number
“Self-PIN Number” is the router’s PIN. Whenever you
want to change the PIN, click “Regenerate PIN” and
“Apply Changes.” To create your own PIN, enter a four-
digit PIN without checksum and click “Apply Changes.”
However, this would not be recommended, since the
registrar side needs to be supported with a four-digit PIN.
Click to regenerate the Self-PIN Number.
Regenerate PIN
Push Button
Configuration
Start PBC
Clicking this button will invoke the PBC method of WPS.
It is only used when the router acts as a registrar.
Click to start the Push Button method of WPS.
Click to restore the original values.
Reset
Client PIN Number
This is only used when users want their station to join the
router’s network. The length of the PIN is limited to four
57
Download from Www.Somanuals.com. All Manuals Search And Download.
or eight numeric digits. If users enter an eight-digit PIN
with checksum error, a warning message pops up. If
users insist on this PIN, the router will take it.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.5 QoS
The router supports the IP QoS feature, which can provide different priorities to
different users or data flows.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
IP QoS
Description
Click the radio button to enable or disable the function.
Select the default mode of QoS from the menu.
• IP Precedence: In QoS, a three-bit field in the ToS byte
of the IP header (see RFC 791). Using IP Precedence,
a network administrator can assign values from 0 (the
default) to 7 to classify and prioritize types of traffic.
• 802.1P: IEEE 802.1p is a three-bit field within an
Ethernet frame header when using tagged frames on an
802.1 network. It specifies a priority value between 0
and 7 inclusive that can be used by Quality of Service
(QoS) disciplines to differentiate traffic.
Default QoS
Source IP
The IP address of the traffic source.
Source Netmask
The source IP netmask. This field is required if the
source IP has been entered.
Source Port
The source port of the selected protocol. You cannot
configure this field without entering the protocol first.
The IP address of the traffic destination.
Destination IP
Destination Netmask The destination IP netmask. This field is required if the
destination IP has been entered.
Destination Port
The destination port of the selected protocol. You cannot
configure this field without entering the protocol first.
The selections are TCP, UDP, ICMP and blank for none.
This field is required if the source port or destination port
has been entered.
Protocol
Physical Port
The incoming ports. The selections include LAN ports,
wireless port and blank for not applicable.
Outbound Priority
The priority level for the traffic that matches this
classification rule. The possible selections are (in the
descending priority): p0, p1, p2, p3.
802.1p
Select this field to mark the three-bit user-priority field in
the 802.1p header of the packet that matches this
classification rule. Note that this 802.1p marking is
workable on a given PVC channel only if the VLAN tag is
enabled in this PVC channel.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Precedence
TOS
Select this field to mark the IP precedence bits in the
packet that match this classification rule.
The IP (Internet Protocol) uses the ToS (Type of Service)
field to provide an indication of the quality of service
desired. These parameters are to be used to guide the
selection of the actual service parameters when
transmitting an IP datagram through a particular network.
This table lists the rules you have configured. Click
“Delete Selected” to delete the selected rules or click
“Delete All” to delete all the rules.
IP QoS Rules
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.6 NAT (Network Address Translations)
NAT (network address translations) solve the problem of sharing a single IP
address among multiple computers. Without NAT, all computers must be
assigned with a valid Internet IP address to get connected to the Internet; but
Internet service providers provide only a limited number of IP addresses to each
user. Therefore, it’s necessary to use NAT technology to share a single Internet
IP address among multiple computers on local network so everyone can get
connected.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.6.1 Port Forwarding
Port Forwarding allows you to re-direct a particular range of service port numbers
(from the Internet) to a particular LAN IP address. It helps you to host some
servers behind the router’s NAT firewall.
Parameter
Port Forwarding
Protocol
Description
Check to enable or disable the port-forwarding feature.
This is the protocol type to be forwarded. You can
forward ‘tCP” or “UDP” packets only, or you can select
“Both” to forward both ‘tCP” and “UDP” packets.
Enter any comments for the setting.
Comment
Enable
Check this item to enable this entry.
Local IP Address
IP address of your local server that will be accessed by
the Internet.
Local IP Port
Remote IP Address
Public Port
The destination port number that is made open for this
application on the LAN side.
The source IP address from which incoming traffic is
allowed. Leave blank for all.
The destination port number that is made open for this
application on the WAN side.
Interface
Select the WAN interface on which the port-forwarding
rule is to be applied.
Current Port
To remove the port forwarding settings from the table,
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Forwarding Table
select the items and click “Delete Selected.” To remove
all settings, just click “Delete All.”
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.6.2 Port Mapping
The router provides multiple interface groups. Up to five interface groups are
supported, including one default group. The LAN and WAN interfaces could be
included. Traffic coming from one interface of a group can only be flowed to the
interfaces in the same interface group. Thus, the router can isolate traffic from
group to group for some applications. By default, all the interfaces (LAN and
WAN) belong to the default group, and the other four groups are all empty. It is
possible to assign any interface to any one group.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Disabled/Enabled
Click the radio button to enable or disable the feature. If
disabled, all interfaces belong to the default group.
To manipulate a mapping group:
Interface groups
1. Select a group from the table.
2. Select interfaces from the available/grouped interface
list and add to the grouped/available interface list using
the arrow buttons to manipulate the required mapping of
the ports.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.6.3 UPNP
When the UPnP function is enabled, the router can be detected by UPnP-
compliant systems such as Windows XP. The router will be displayed in the
Neighborhood of Windows XP, so you can directly double-click the router or
right- click the router and select “Invoke” to configure the router through a Web
browser.
Parameter
UPnP
Description
Enable or disable the UPnP feature.
The upstream WAN interface is selected here. Select a
WAN interface that will use UPnP from the drop-down
menu.
WAN Interface
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.6.4 IGMP Proxy
When IGMP Proxy (Internet Group Management Protocol Proxy) is enabled, the
router can make intelligent multicast forwarding decisions by examining the
contents of each frame’s IP header. Without the function, the router will
broadcast the multicast packets to each port and may create excessive traffic on
the network and degrade the performance of the network.
The IGMP Proxy screen allows you to enable multicast on WAN and LAN
interfaces. The LAN interface always serves as a downstream IGMP proxy, and
you can configure one of the available WAN interfaces as the upstream IGMP
proxy. Upstream is the interface used when IGMP requests from hosts are sent
to the multicast router. Downstream is the interface used when data from the
multicast router are sent to hosts in the multicast group database.
Parameter
Description
IGMP Proxy
Proxy Interface
Enable or disable the IGMP proxy feature.
The upstream WAN interface is selected here.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.7 Firewall
The Firewall section contains several features that are used to deny or allow
traffic from passing through the router.
5.2.7.1 IP/Port Filtering
The IP/Port Filtering feature allows you to deny/allow specific services or
applications in the forwarding path.
Parameter
Outgoing Default
Action
Description
Specify the default action on the LAN-to-WAN (Traffic-to-
Internet) forwarding path. Choose “Allow” to allow the IP
addresses listed in the following table to connect to the
Internet; choose “Deny” to deny the IP addresses listed
in the following table from connecting to the Internet.
Specify the default action on the WAN-to-LAN (Traffic-
from-Internet) forwarding path. Choose “Allow” to allow
the IP addresses listed in the following table to connect
to the Internet; choose “Deny” to deny the IP addresses
Incoming Default
Action
66
Download from Www.Somanuals.com. All Manuals Search And Download.
listed in the table from connecting to the Internet.
Select the traffic forwarding direction: outgoing or
incoming.
Direction
Protocol
There are three options available: TCP, UDP and ICMP.
Deny or allow traffic when matching this rule.
Enter the start IP address that will be monitored.
Enter the subnet mask based on the source IP address.
LAN users use port numbers to distinguish one network
application from another; for example, 21 is for FTP
service. The port number range is from 0 to 65535. It is
recommended that this option be configured by an
advanced user.
Rule Action
Source IP Address
Subnet Mask
Port
Destination IP Address Enter the destination IP address that will be monitored.
Subnet Mask
Enter the subnet mask based on the destination IP
address.
Port
This is the port or port ranges that define the application.
To remove some IP/Port Filter settings from the Current
Filter Table, select the items you want to remove in the
list and click “Delete Selected.” To remove all the items
from the table, click “Delete All.”
Current Filter Table
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.7.2 MAC Filtering
The MAC Filtering feature allows you to define rules to allow or deny frames
through the router based on source MAC address, destination MAC address and
traffic direction.
Parameter
Outgoing Default
Action
Description
Specify the default action on the LAN-to-WAN (Traffic-to-
Internet) forwarding path. Choose “Allow” to allow the IP
addresses listed in the following table to connect to the
Internet; choose “Deny” to deny access.
Incoming Default
Action
Specify the default action on the WAN-to-LAN (Traffic-
from-Internet) forwarding path. Choose “Allow” to allow
the IP addresses listed in the following table to connect
to the Internet; choose “Deny” to deny access.
Traffic bridging/forwarding direction: outgoing or
incoming.
Direction
Rule Action
Deny or allow traffic when matching this rule.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Source MAC Address This must be in 12-digit hexadecimal format; for example,
“00-d0-59-c6-12-43.”
Destination MAC
Address
This must be in 12-digit hexadecimal format; for example,
“00-d0-59-c6-12-50.”
Current Filter Table
To remove some filter rules from the Current Filter Table,
select the MAC address you want to remove and click
“Delete Selected.” To remove all settings, click “Delete
All.”
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.7.3 URL Blocking
This screen is used to block some URL addresses or keywords.
Parameter
URL Blocking
FQDN
Description
Enable or disable the URL Blocking function.
Enter the FQDN which you want to block. A FQDN is a
complete DNS name. For example, “www.yahoo.com.”
The FQDN settings will be listed in the table. To delete
some settings, select the settings and click “Delete
Selected.” To remove all settings,click “Delete All.”
Enter the keyword of the URL address you want to filter.
The keyword settings will be listed in the table. To delete
some keyword settings, select them and click “Delete
Selected.” To remove all settings, click “Delete All.”
URL Blocking Table
Keyword
Keyword Filtering
Table
70
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.7.4 Domain Blocking
The firewall includes the ability to block access to specific domains based on
string matches. For example, if the URL of the Martian Yahoo Web site is
“ma.yahoo.com” and you enter “yahoo.com,” the firewall will block all the DNS
queries with a “yahoo.com” string. So the host will be blocked from accessing all
the URLs belonging to the “yahoo.com” domain. That means you can protect
your computer, your house, your office and anything else that uses DNS from
being able to service domains that you don’t want to load.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Domain Blocking
Domain
Description
Check this item to enable the Domain Blocking feature.
The blocked domain. If the URL of the Mars Yahoo Web
site is ma.yahoo.com, the domain can be yahoo.com.
Delete Selected/All
To delete a specific Domain Block entry, check the
“Select” box of the Domain Block you want to delete,
then click “Delete Selected.” To remove all settings from
the table, click “Delete All.”
5.2.7.5 Routing Configuration
This screen enables you to define a specific route for your Internet and network
data. Most users do not need to define routes. On a typical small home or office
LAN, the existing routes that set up the default gateways for your LAN hosts and
for the router provide the most appropriate path for all your Internet traffic. You
may need to define routes if your home setup includes two or more networks or
subnets, if you connect to two or more ISP services, or if you connect to a remote
corporate LAN.
Parameter
Description
Enable
Check to enable the selected route or route to be added.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Destination
The destination can be specified as the IP address of a
subnet or a specific host in the subnet. It can also be
specified as all zeros to indicate the route should be used
for all destinations for which no other route is defined
(this is the route that creates the default gateway).
The network mask of the destination subnet. The default
gateway uses a mask of 0.0.0.0.
Subnet Mask
Next Hop
Metric
The IP address of the next hop through which traffic will
flow toward the destination subnet.
Defines the number of hops between network nodes that
data packets travel. The default value is 0, which means
that the subnet is directly one hop away on the local LAN
network.
Interface
The WAN interface to which a static routing subnet is to
be applied.
Show Routes
Click to view the router’s routing table.
Static Route Table
Click “Update” to update the selected destination route in
the Static Route Table. Click “Delete Selected” to delete
a selected destination route in the table.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.7.6 ACL Configuration
The Access Control List (ACL) is a list of permissions attached to the router that
specifies who is allowed to access this router. If ACL is enabled, all hosts cannot
access this router except for the hosts with an IP address in the ACL table.
Parameter
ACL Capability
Enable
Description
Enable or disable the ACL function.
Check to enable this ACL entry.
Interface
Select the interface domain: LAN or WAN.
Enter the IP address that is allowed to access the router.
Enter the subnet mask that is allowed to access the router.
The ACL settings will be listed here. Click “Delete Selected” to
delete the settings you have selected. To remove all settings
from the table, click “Delete All.”
IP Address
Subnet Mask
ACL Table
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.7.7 DMZ
The DMZ Host is a local computer exposed to the Internet. When setting a
particular internal IP address as the DMZ Host, all incoming packets will be
checked by the firewall and NAT algorithms, then passed to the DMZ Host.
For example, if you have a local client PC that cannot run an Internet application
(e.g., games) properly from behind the NAT firewall, then you can open the client
up to unrestricted two-way Internet access by defining a DMZ Host.
Parameter
Description
DMZ Host
Check the item to enable the DMZ function.
DMZ Host IP Address Enter a static IP address to the DMZ host. This IP
address will be exposed to the Internet.
When you finish, click “Apply Changes.” You’ll see the following message
displayed on Web browser.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Click “Continue” to save the settings made and go back to the Web management
interface; click “Apply” to save the settings made and restart the router so the
settings will take effect after it reboots.
5.3 Status
This screen displays the ADSL modem/router’s current status and settings. This
information is read-only except for the PPPoE/PPPoA channel, for which you can
connect/disconnect the channel on demand. Click “Refresh” to update the status
function buttons on this screen.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.1 Interface
You can view statistics on the processing of IP packets on the networking
interfaces. You will not typically need to view this data, but you may find it helpful
when working with your ISP to diagnose network and Internet data transmission
problems. To display statistics for any new data, click “Refresh.”
77
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.2 ADSL
This screen shows the ADSL line statistic information.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Tools
The Tools section includes the basic configuration tools, such as Back Up,
Restore Configuration Settings, Upgrade System Firmware and Diagnostic Test.
5.4.1 Configuration Tools
This screen allows you to back up the current settings to a file or restore the
settings from the file that was saved previously. You can also reset the current
configuration to factory defaults.
Parameter
Description
Save Settings to File Click “Save” to save the router’s current configuration to
a file named “config.bin” on your PC.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Load Settings from File Click “Browse” to search for a file you saved before, and
click “Upload” to restore the saved configuration.
Restore Settings to
Default
Click “Reset” to force the router to perform a power reset
and restore the original factory settings.
5.4.2 Firmware Upgrade
This screen allows you to upgrade the firmware for the router. Click “Browse” to
select the firmware file and click “Upload” to start upgrading.
IMPORTANT! Do not turn off your router while this procedure is in progress.
5.4.3 Ping
Once you have your router configured, you can send a ping command to the host
you specify on this screen. To use it, you must enter the IP address of the host
you are trying to communicate with in the “Host Address” field.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4.4 ATM Loopback
In order to isolate ATM interface problems, you can use ATM OAM loopback
cells to verify connectivity between VP/VC endpoints, as well as segment
endpoints within the VP/VC. This screen allows you to use ATM ping to test the
reachability of a segment endpoint or a connection endpoint.
Parameter
Description
Select PVC
Select the PVC channel you want to do the loop-back
diagnostic.
Flow Type
The ATM OAM flow type. The selection can be F5 Segment or
F5 End-to-End. ATM uses F4 and F5 cell flows:
• F4: used in VPs
• F5: used in VCs
Loopback
The loop-back location ID field of the loop-back cell. The
default value is all 1s (ones) to indicate the endpoint of the
segment or connection.
Location ID
Click “Go!” to save the setting to the configuration.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4.5 Diagnostic Test
The Diagnostic Test screen shows the test results for the connectivity of the
physical layer and protocol layer for both LAN and WAN sides.
5.4.6 Reboot
Whenever you use the Web configuration to change system settings, the
changes are initially placed in temporary storage. To save your changes for
future use, you need to click “Commit and Reboot” to reboot the router. If you
have encountered some problems during the configurations, press the “Reset”
button on the rear panel of the router and hold it in for 10 seconds or more to
reset default settings.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Troubleshooting
The LAN LED on the front panel does not light up.
STEPS
CORRECTIVE ACTION
1
Check the Ethernet cable connections between your router and
the computer or hub.
2
3
4
Check for faulty Ethernet cables.
Make sure your computer’s Ethernet card is working properly.
If these steps fail to correct the problem, contact your local
distributor for assistance.
The ADSL LED on the front panel does not light up.
STEPS
CORRECTIVE ACTION
1
Check the telephone wire and connections between router DSL
port and the wall jack.
2
Make sure that the telephone company has checked your phone
line and set it up for DSL service.
3
4
Reset your ADSL line to reinitialize your link to the DSLAM.
If these steps fail to correct the problem, contact your local
distributor for assistance.
I cannot access the Web management.
STEPS
CORRECTIVE ACTION
1
2
Make sure you are using the correct IP address of router.
Your computer and the router’s IP addresses must be on the
same subnet for LAN access.
3
If you have changed router’s LAN IP address, then enter the new
one as the URL.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
The following procedures will help you to check the current IP address setting of
your computer. You can compare if your computer and the router’s IP addresses
are in the same subnet.
Step 1: Click “Start” and select “Run.”
Step 2: Enter “cmd” in the “Open” text field and click “OK.”
Step 3: Input “ipconfig/al”l and press <Enter> on your keyboard.
Your PC’s IP address is 192.168.2.111.
The PC’s subnet mask is 255.255.255.0.
Your PC’s MAC address is the one listed as Physical Address (00-00-E2-82-C3-
AD).
84
Download from Www.Somanuals.com. All Manuals Search And Download.
I forget my login username and/or password.
STEPS
CORRECTIVE ACTION
1
If you have changed the password and have now forgotten it, you
will need to upload the default configuration file. This will erase all
custom configurations and restore all of the factory defaults,
including the password.
2
3
Press and hold in the Reset/WPS button for over five seconds,
then release it. When the Power LED begins to blink, the defaults
have been restored.
The default username is “admin.” The default password is “1234.”
The Password and Username fields are case-sensitive. Make
sure that you enter the correct password and username using the
proper case.
4
It is highly recommended that you change the default username
and password. Make sure you store the username and password
in a safe place.
I cannot access the Web Management of the router after activating the ACL
function.
STEPS
CORRECTIVE ACTION
1
When ACL is activated, you need to set the ACL rule for allowing
some users to use some services. Check if you have set the
rules. If not, all the users are forbidden to use any of service from
the LAN or WAN.
2
3
If you cannot access the Web management of the router, press
and hold in the Reset/WPS button over 5 seconds to restore to
defaults.
After the router has restarted, log in to the router with the default
IP address 192.168.2.1.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Initialization of the ADSL connection failed.
STEPS
CORRECTIVE ACTION
1
Check the cable connections between the ADSL port and the
wall jack. The ADSL LED on the rear panel of the router should
be on.
2
3
Check that the VPI, VCI, Type of Encapsulation and Type of
Multiplexing settings are the same as what you collected from
your ISP.
Restart the router. If you still have problems, you may need to
verify your VPI, VCI, Type of Encapsulation and Type of
Multiplexing settings with the ISP.
I cannot get a WAN IP address from the ISP.
STEPS
CORRECTIVE ACTION
1
The ISP provides the WAN IP address after authenticating you.
Authentication may be through the user name and password, the
MAC address or the host name.
2
The username and password apply to PPPoE and PPoA
encapsulation only. Make sure that you have entered the correct
Service Type, User Name and Password (be sure to use the
correct case).
Internet connection disconnects.
STEPS
CORRECTIVE ACTION
1
2
Check the connection type.
If you use PPPoA or PPPoE encapsulation, check the idle time-
out setting.
3
Contact your ISP.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Glossary
10Base-T
It is an Ethernet standard for a local area network (LAN). 10Base-T uses a
twisted pair cable with a maximum length of 100 meters.
AAL
ATM is an adaptation layer that defines the rules governing segmentation and
reassembly of data into cells. Different AAL types are suited to different traffic
classes.
ADSL
An asymmetric digital subscriber line is an asymmetrical data transmission
technology with a high traffic rate downstream and a low traffic rate upstream.
ADSL technology satisfies the bandwidth requirement of applications that
demand “asymmetric” traffic, such as Web surfing, file downloads and video-on-
demand (VOD).
ATM
Asynchronous transfer mode is a Layer 2 protocol supporting high-speed
asynchronous data with advanced traffic management and quality-of-service
features.
Bridge
A device that connects two or more physical networks and forwards packets
between them. Bridges can usually be made to filter packets; that is, to forward
only certain traffic. Related devices are repeaters, which simply forward electrical
signals from one cable to another, and full-fledged routers, which make routing
decisions based on several criteria.
Default Gateway (Router)
Every non-router IP device needs to configure a default gateway’s IP address.
When the device sends out an IP packet, if the destination is not on the same
network, the device has to send the packet to its default gateway, which will then
send it out toward the destination.
DHCP
The Dynamic Host Configuration Protocol automatically gives every computer on
your home network an IP address.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
DNS Server IP Address
DNS stands for domain name system, which allows Internet servers to have a
domain name (such as www.ADSLrouter.com) and one or more IP addresses
(such as 192.34.45.8). A DNS server keeps a database of Internet servers and
their respective domain names and IP addresses, so that when a domain name
is requested (as in typing “ ADSLrouter.com” into your Internet browser), the user
is sent to the proper IP address. The DNS server IP address used by the
computers on your home network is the location of the DNS server your ISP has
assigned to you.
DSL
Digital line subscriber (DSL) technology provides high-speed access over twisted
copper pair for connection to the Internet, LAN interfaces and DSL services such
as video-on-demand, distance learning and video conferencing.
Ethernet
The standard for computer networks, Ethernet networks are connected by
special cables and hubs or switches, and move data around at up to 10/100
million bits per second (Mbps).
FTP
The File Transfer Protocol is the Internet protocol (and program) used to transfer
files between hosts.
Idle Timeout
Idle timeout is designed so that when there is no traffic to the Internet for a pre-
configured amount of time, the connection will automatically be disconnected.
ISP
An Internet service provider is a business that provides connectivity to the
Internet for individuals and other businesses or organizations.
ISP Gateway Address
This is an IP address for the Internet router located at the ISP’s office.
LAN
A local area network is a group of computers and devices connected together in
a relatively small area (such as a house or an office). Your home network is
considered a LAN.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
MAC Address
MAC stands for media access control. A MAC address is the hardware address
of a device connected to a network. The MAC address is a unique identifier for a
device with an Ethernet interface. It is composed of two parts: 3 bytes of data
that corresponds to the manufacturer ID (unique for each manufacturer), plus 3
bytes that are often used as the product’s serial number.
NAT
A network address translator is defined by RFC 1631. It enables a LAN network
to use one set of IP addresses for internal traffic. A NAT box located where the
LAN meets the Internet provides the necessary IP address translation. This helps
provide a sort of firewall and allows for a wider address range to be used
internally without danger of conflict. Using the router’s NAT capability, you can
access the Internet from any computer on your home network without having to
purchase more IP addresses from your ISP.
Port
Network clients (LAN PC) uses port numbers to distinguish one network
application/protocol from another. Below is a list of common applications and
protocol/port numbers.
Application
Telnet
Protocol Port Number
TCP
TCP
TCP
TCP
TCP
UCP
UDP
TCP
TCP
23
FTP
21
SMTP
25
POP3
110
1720
161
162
80
H.323
SNMP
SNMP Trap
HTTP
PPTP
1723
5631
5632
PC Anywhere TCP
PC Anywhere UDP
89
Download from Www.Somanuals.com. All Manuals Search And Download.
PPP
PPP is the Point-to-Point-Protocol. The successor to SLIP, PPP provides router-
to-router and host-to-network connections over both synchronous and
asynchronous circuits.
PPPoA (RFC 2364)
The Point-to-Point Protocol (PPP) provides a standard method for transporting
multi-protocol datagrams over point-to-point links. This document describes the
use of ATM Adaptation Layer 5 (AAL5) for framing PPP encapsulated packets.
PPPoE (RFC 2516)
This document describes how to build PPP sessions and encapsulate PPP
packets over Ethernet. PPP over Ethernet (PPPoE) provides the ability to
connect a network of hosts over a simple bridging access device to a remote
Access Concentrator.
Protocol
A protocol is a set of rules for interaction agreed upon between multiple parties
so that when they interface with each other based on such a protocol, the
interpretation of their behavior is well defined and can be made objectively,
without confusion or misunderstanding.
PVC
A permanent virtual circuit is a connection-oriented, permanent leased-line circuit
between end stations on a network over a separate ATM circuit.
RFC
Request for Comments is the document series, begun in 1969, that describes the
Internet suite of protocols and related experiments. Not all RFCs describe
Internet standards, but all Internet standards are written up as RFCs.
RFC 1483
This is a multi-protocol encapsulation over AAL-5: two encapsulation methods for
carrying network interconnect traffic over ATM AAL-5. The first method allows
multiplexing of multiple protocols over a single ATM virtual circuit. The protocol of
a carried PDU is identified by prefixing the PDU by an IEEE 802.2 Logical Link
Control (LLC) header. The second method does higher-layer protocol
multiplexing implicitly by ATM Virtual Circuits (VCs).
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Router
A system responsible for making decisions about which of several paths network
(or Internet) traffic will follow. To do this, it uses a routing protocol to gain
information about the network and algorithms in order to choose the best route
based on several criteria known as “routing metrics.”
Subnet Mask
A subnet mask, which may be a part of the TCP/IP information provided by your
ISP, is a set of four numbers (e.g., 255.255.255.0) configured like an IP address.
It is used to create IP address numbers used only within a particular network (as
opposed to valid IP address numbers recognized by the Internet, which must be
assigned by InterNIC).
TCP/IP, UDP
Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable
Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission
over the Internet. Both TCP and UDP are transport layer protocols. TCP
performs proper error detection and error recovery, and thus is reliable. UDP, on
the other hand, is not reliable. They both run on top of the IP (Internet Protocol),
a network layer protocol.
VCI
A virtual circuit identifier is part of the ATM cell header. A VCI is a tag indicating
the channel over which a cell will travel. The VCI of a cell can be changed as it
moves between switches via signaling.
VPI
A virtual path identifier is part of the ATM cell header. A VPI is a conduit for a
number of virtual circuits.
WAN
A wide area network is a network that connects computers located in
geographically separate areas (e.g., different buildings, cities, countries). The
Internet is a wide area network.
Web-based Management Graphical User Interface (GUI)
Many devices support a graphical user interface that is based on the Web
browser. This means the user can use the familiar Netscape or Microsoft Internet
Explorer to control/configure or monitor the device being managed.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Specifications
Standards
• IEEE 802.3 (10Base-T Ethernet)
• IEEE 802.3u (100Base-TX Fast Ethernet)
• IEEE 802.11b (11 Mbps Wireless LAN)
• IEEE 802.11g (54 Mbps Wireless LAN)
• IEEE 802.11n Draft 2.0 (300 Mbps Wireless LAN)
• ADSL2+ (ITU G.992.5) up to 24 Mbps
• ADSL2 (ITU G.992.4) splitterless ADSL, up to 12 Mbps
• ADSL2 (ITU G.992.3) up to 12 Mbps
• ADSL (ITU G.992.2/G.Lite) up to 1.5 Mbps
• ADSL (ITU G.992.1/G.DMT) up to 8 Mbps
• ANSI T1.413, Issue 2 (Asymmetric DSL)
General
• LAN ports: 4 RJ45 10/100 Mbps data ports
• LAN ports with Auto MDI/MDI-X
• WAN port: 1 x RJ11 (ADSL)
• Flash: 2 MB
• Memory: 16 MB SDRAM
• Throughput max.: 24 Mbps downstream, 1 Mbps upstream
• Certifications: FCC Class B, CE, RoHS
Router
• Chipset: Realtek RTL8671BH + RTL8271B
• Supported WAN connection types:
- PPP over Ethernet (RFC 2516)
- PPP over AAL5 (RFC 2364)
- Multiple protocols over AAL5 (RFC 1483/2684)
• NAT:
- Port forwarding
- DMZ (demilitarized zone)
• Firewall:
- Access control based on MAC address
92
Download from Www.Somanuals.com. All Manuals Search And Download.
- URL filter
• Supports UPnP (Universal Plug and Play)
• Supports DHCP (client/server)
• Supports VPN PPTP, L2TP and IPsec passthrough
Wireless
• Chipset: Realtek RTL8192SU
• Wireless frequency range: 2.4 – 2.4835 GHz
• Modulation technologies:
- 802.11b: Direct Sequence Spread Spectrum (DSSS): DBPSK, DQPSK, CCK
- 802.11g: Orthogonal Frequency Division Multiplexing (OFDM): BPSK, QPSK,
16QAM, 64QAM
- 802.11n: Orthogonal Frequency Division Multiplexing (OFDM): BPSK, QPSK,
16QAM, 64QAM
• Channels:
- USA & Canada: 11 channels
- Europe: 13 channels
- Japan: 14 channels
• Data rates:
- IEEE 802.11b (11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps)
- IEEE 802.11g (54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9
Mbps, 6 Mbps)
• Output power:
- OFDM: 15 dBm +/- 1.5 dBm (54 Mbps, 32 mW max.)
- OFDM: 13 dBm +/- 1.5 dBm (300 Mbps, 20 mW max.)
- CCK: 16 dBm +/- 1.5 dBm (11 Mbps, 40 mW max.)
• Wireless security:
- WEP encryption (64/128 bit)
- WPA TKIP
- WPA2 AES
- WPA2 mixed
- WPA RADIUS
- Client access control through media access control (MAC) filter
• Antennas:
- 2 fixed dipole antennas with 3 dBi gain each
93
Download from Www.Somanuals.com. All Manuals Search And Download.
- 2T2R MIMO mode (2 transmitter, 2 receiver)
LEDs
• Power
• WLAN
• WPS
• ADSL Link/Act
• LAN 1-4 Link/Act
Environmental
• Dimensions: 187 (W) x 100 (D) x 30 (H) mm (7.3 x 3.9 x 1.2 in.)
• Weight: 0.8 kg (1.7 lbs.)
• Operating temperature: 0 – 40°C (32 – 104°F)
• Operating humidity: 10 – 90% RH, non-condensing
• Storage temperature: 0 – 60°C (0 – 149°F)
Power
• External power adapter: 12 V DC, 1 A
Package Contents
• Wireless 300N ADSL 2+ Modem Router
• Quick installation guide
• Setup CD with user manual and setup wizard
• Power adapter
• Ethernet Cat5 RJ45 cable, 1.0 m (3 ft.)
• RJ11 telephone cable, 1.8 m (5.9 ft.)
94
Download from Www.Somanuals.com. All Manuals Search And Download.
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
Disposal of Electric and Electronic Equipment
(applicable in the European Union and other European countries with
separate collection systems)
ENGLISH
This symbol on the product or its packaging indicates that this product shall not be
treated as household waste. Instead, it should be taken to an applicable
collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences to the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product. If your equipment contains easily removable batteries or accumulators,
dispose of these separately according to your local requirements. The recycling
of materials will help to conserve natural resources. For more detailed information
about recycling of this product, contact your local city office, your household waste
disposal service or the shop where you purchased this product. In countries
outside of the EU: If you wish to discard this product, contact your local
authorities and ask for the correct manner of disposal.
DEUTSCH
Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an, dass
dieses Produkt nicht mit dem Hausmüll entsorgt werden darf. In Übereinstimmung
mit der Richtlinie 2002/96/EG des Europäischen Parlaments und des Rates über
Elektro- und Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät nicht im
normalen Hausmüll oder dem Gelben Sack entsorgt werden. Wenn Sie dieses
Produkt entsorgen möchten, bringen Sie es bitte zur Verkaufsstelle zurück oder zum
Recycling-Sammelpunkt Ihrer Gemeinde.
ESPAÑOL
Este símbolo en el producto o su embalaje indica que el producto no debe tratarse
como residuo doméstico. De conformidad con la Directiva 2002/96/CE de la UE
sobre residuos de aparatos eléctricos y electrónicos (RAEEI), este producto
eléctrico no puede desecha se con el resto de residuos no clasificados. Deshágase
de este producto devolviéndolo al punta de venta o a un punta de recogida
municipal para su reciclaje.
FRANÇAIS
Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doit pas
être traité comme un déchet ménager. Conformément à la Directive 2002/96/EC
sur les déchets d’équipements électriques et électroniques (DEEE), ce produit
électrique ne doit en aucun cas être mis au rebut sous forme de déchet
municipal non trié. Veuillez vous débarrasser de ce produit en Ie renvoyant à son
point de vente ou au point de ramassage local dans votre municipalité, à des fins
de recyclage.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
ITALIANO
Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto non va
trattato come un rifiuto domestico. In ottemperanza alla Direttiva UE 2002/96/EC
sui rifiuti di apparecchiature elettriche ed elettroniche (RAEEI), questa prodotto
elettrico non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire
il prodotto riportandolo al punto vendita o al punto di raccolta municipale locale per
un opportuno riciclaggio.
POLSKI
Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w
czasie utylizacji nie wolno wyrzucać tego produktu wraz z odpadami komunalnymi.
Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie zużytego sprzętu elektrycznego i
elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać
jako nie posortowanego odpadu komunalnego. Prosimy o usuniecie niniejszego
produktu poprzez jego zwrot do punktu zakupu lub oddanie do miejscowego
komunalnego punktu zbiórki odpadów przeznaczonych do recyklingu.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
ENGLISH: For warranty information, go to
www.intellinet-network.com/warranty.
DEUTSCH: Garantieinformationen finden Sie unter
www.intellinet-network.com/warranty.
ESPAÑOL: Si desea obtener información sobre la garantía, visite
www.intellinet-network.com/warranty.
FRANÇAIS: Pour consulter les informations sur la garantie, visitez
www.intellinet-network.com/warranty.
POLSKI: Informacje dotyczące gwarancji znajdują się na stronie
www.intellinet-network.com/warranty.
ITALIANO: Per informazioni sulla garanzia, accedere a
www.intellinet-network.com/warranty.
EN MÉXICO: Poliza de Garantia INTELLINET — Datos del importador y
responsable ante el consumidor IC Intracom México, S.A. de C.V. • Av. Interceptor
Poniente # 73, Col. Parque Industrial La Joya, Cuautitlan Izcalli, Estado de México,
C.P. 54730, México. • Tel. (55)1500-4500
La presente garantía cubre este producto por 3 años contra cualquier defecto de
fabricación en sus materiales y mano de obra, bajo las siguientes condiciones:
1. Todos los productos a que se refiere esta garantía, ampara su cambio físico,
sin ningún cargo
para el consumidor.
2. El comercializador no tiene talleres de servicio, debido a que los productos
que se garantizan no cuentan con reparaciones, ni refacciones, ya que su
garantía es de cambio físico.
3. La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles que
hayan sido instaladas defábrica y no incluye en ningún caso el equipo adicional o
cualesquiera que hayan sido adicionados al mismo por el usuario o distribuidor.
Para hacer efectiva esta garantía bastara con presentar el producto al distribuidor
en el domicilio donde fue adquirido o en el domicilio de IC Intracom México, S.A.
de C.V., junto con los accesorios contenidos en su empaque, acompañado de su
póliza debidamente llenada y sellada por la casa vendedora (indispensable el
sello y fecha de compra) donde lo adquirió, o bien, la factura o ticket de compra
original donde se mencione claramente el modelo, numero de serie (cuando
aplique) y fecha de adquisición. Esta garantia no es valida en los siguientes
casos: Si el producto se hubiese utilizado en condiciones distintas a las
normales; si el producto no ha sido operado conforme a los instructivos de uso; ó
si el producto ha sido alterado o tratado de ser reparado por el consumidor ó
terceras personas.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
All products mentioned are trademarks or registered trademarks of their
respective owners.
Copyright © INTELLINET NETWORK SOLUTIONS
98
Download from Www.Somanuals.com. All Manuals Search And Download.
|