Contents
Before using
Important Safeguards ........................................ 2
Precautions ........................................................ 3
Features ............................................................. 4
Supplied accessories ......................................... 4
Before operating this unit ................................. 5
A / V Receiver
Preparation
DTR-7
DTR-6
Audio equipment connections .......................... 6
Video equipment connections........................... 8
Connecting equipment
with 5.1-channel output .................................. 9
Connecting speakers ....................................... 10
Connecting power amplifiers .......................... 12
Connecting an equalizer.................................. 13
Connecting the power ..................................... 13
Making antenna connections .......................... 14
Instruction Manual
Operation
Using the on-screen display ............................ 16
Setting the speaker configuration ................... 18
Setting the speaker distance ............................ 20
Setting the speaker Level ................................ 21
Playing a digital source ................................... 23
Presetting FM/AM radio stations.................... 24
Selecting an input source ................................ 26
Selecting a preset station................................. 32
Playing a multichannel input source ............... 33
Using the Listening Modes ............................. 34
Setting the listening mode parameters .................... 38
Assigning a video source
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
SANDBY MULTI SOURCE
POWER
PUSH TO ENTER
ON
OFF
LISTENING MODE
REC OUT/
MULTI SOURCE
DIGITAL/
ANALOG
A
SPEAKERS
B
DISPLAY
DSP
CH LEVEL
DIRECT
STEREO
/DTS
THX
SURROUND
MODE
(MONO)
VIDEO4
PHONES
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
C
D
S
VIDEO
VIDEO
L
AUDIO R(MONO)
DTR-7 by
to each audio input source .............................. 40
Giving a name to each input source
and preset radio station ................................... 41
Adjusting the output level of each speaker
while listening to it ......................................... 42
Other setup operations .................................... 43
Recording a source.......................................... 44
Using Multi-Room Remote System................ 46
The initial settings........................................... 48
Thank you for purchasing the Integra Audio Video
Control Receiver.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Audio Video Control
Receiver.
Please retain this manual for future reference.
Appendix
Using the remote controller ............................ 49
Programming the remote controller codes of
other devices into the RC-392M ..................... 52
Using a Macro function .................................. 54
Troubleshooting guide .................................... 58
Specifications .................................................. 60
Control positions and names ........................... 62
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Warranty Claim
For Canadian model
You can find the serial number on the rear panel of this unit. In case
of warranty claim, please report this number.
CAUTION: THIS DIGITAL APPARATUS DOES NOT EXCEED
THE CLASS B LIMITS FOR RADIO NOISE EMISSION FROM
DIGITAL APPARATUS SET OUT IN THE RADIO INTERFER-
ENCE REGULATIONS OF THE CANADIAN DEPARTMENT
OF COMMUNICATIONS.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
2. Recording Copyright
Recording of copyrighted material for other than personal use is il-
legal without permission of the copyright holder.
3. AC Fuse
The fuse is located inside the chassis and is not user-serviceable. If
power does not come on, contact your Onkyo authorized service sta-
tion.
Modele pour les Canadien
ATTENTION: L'INTERFÉRENCE RADIO ÉLECTRIQUE
GÉNÉRÉE PAR CET APPAREIL NUMÉRIQUE DE TYPE B NE
DÉPASSE PAS LES LIMITES ÉNONCÉES DANS LE
4. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and
wipe off the dirt. Following this, dry immediately with a clean cloth.
Do not use rough material, thinners, alcohol or other chemical sol-
vents or cloths since these could damage the finish or remove the
panel lettering.
RÈGLEMENT
SUR
LES
PERTURBATIONS
RADIO
ÉLECTRIQUES, SECTION APPAREIL NUMÉRIQUE, DU
MINISTÈRE DES COMMUNICATIONS.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to coun-
try or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC 230
V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Worldwide models are equipped with a voltage selector to conform
to local power supplies. Be sure to set this switch to match the volt-
age of the power supply in your area before plugging in the unit.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s atten-
tion to Article 820-40 of the NEC, ANSI/NFPA 70, which provides
guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Supplied accessories
Check that the following accessories are supplied with this unit.
Key Features
■ THX*1 select (DTR-7 only)
■ DTS*2 decorder built-in
■ Dolby*3 digital decoder built-in
■ Linear PCM 96 kHz/24-bit D/A converter
■ 5.1 multichannel inputs
FM antenna x 1
(Connector shape may vary
depending on where the unit is
purchased.)
AM loop antenna x 1
■ 4 assignable digital inputs (2-coaxial, 2-optical)
■ Optical digital output (DTR-7 only)
■ Onscreen display
■ Main-in jacks for front left & right channels
(DTR-7 only)
■ Pre outs for all channels
Remote controller (RC-392M) x1
Batteries (size AA or UM-3) x 2
■ Banana-plug posts for all channels
■ Aluminum volume control
■ New user-friendly smart scan
■ New backlit learning remote with joy stick
■ 3 audio and 5 AV inputs (all S-video&video)
■ Cinema Re-EQ*4
Power cable x1
■ Multiroom Jack for compatibility with Xantech*5,
Niles*6, and the more popular multiroom A/V
distribution and control systems.
Memory Preservation
This unit does not require memory preservation batteries. A
built-in memory power back-up system preserves the contents
of the memory during power failures and even when the
POWER switch is set to off. The POWER switch must be set to
on in order to charge the back-up system.
Amplifier Design
■ 5-channel amplification
The memory preservation period after the unit has been turned
off varies depending on climate and placement of the unit. On
the average, memory contents are protected over a period of a
few weeks after the last time the unit has been turned off . This
period is shorter when the unit is exposed to a highly humid
climate.
■ Real high-current, 6 Ω low-impedance drive
■ DVD-audio capability
■ Wide Range amplifier technology
■ Discrete output stage circuits for all channels
■ High-quality extruded heat sink
■ Oversized power transformer
■ (DTR-7)
105 W x 5 (8
135 W x 5 (6 Ω 1 kHz 0.1% THD FTC)
■ (DTR-6)
Ω
20 Hz-20 kHz 0.08% THD FTC)
85 W x 5 (8 Ω 20 Hz-20 kHz 0.08% THD FTC)
110 W x 5 (6 Ω 1 kHz 0.1% THD FTC)
*1 Lucasfilm and THX are registered trademarks of Lucasfilm LTD.
*2 Manufactured under license from Digital Theater Systems, Inc. US Pat.
No.5,451,942 and other worldwide patents issues and pending. “DTS”
and “DTS Digital Surround” are trademarks of Digital Theater Systems,
Inc.© 1996 Digital Theater Systems, Inc. All rights reserved.
*3 Manufactured under license from Dolby Laboratories.
THX Select
Before any home theatre component can be THX Select certi-
fied, it must pass a rigorous series of quality and performance
tests. Only then can a product feature the THX Select logo,
which is your guarantee that the Home Theatre products you
purchase will give you superb performance for many years to
come. THX Select requirements define hundreds of param-
eters, including power amplifier performance, and pre-ampli-
fier performance and operation for both digital and analog do-
mains. THX Select receivers also features proprietary THX
technologies (e.g. THX Mode, see page 34) which accurately
translate film soundtracks for home theater playback.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories. Confidential Unpublished Works. ©1992-1997
Dolby Laboratories, Inc. All rights reserved.
*4 Re-Equalization and the “Re-EQ” logo are trademarks of Lucasfilm
Ltd. Manufactured under license of Lucasfilm Ltd.
*5 Xantech is a registered trademark of Xantech Corporation.
*6 Niles is a registered trademark of Niles Audio Corporation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before operating this unit
Installing the remote controller batteries
1. Remove the battery compartment cover by pressing the tab and
lifting up the cover.
1
2. Insert two AA (R6- or UM-3)-size batteries into the battery
compartment. Carefully follow the polarity diagram (positive
(+) and negative (–) symbols) inside the battery compartment.
3. After batteries are installed and seated correctly, replace the
compartment cover.
Notes
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from cor-
rosion. If the remote controller does not operate smoothly, re-
place both the batteries at the same time.
• The life of the batteries supplied is about six months but this will
vary depending on usage.
2
3
Using the remote controller
Point the remote controller toward the remote control sensor.
The STANDBY indicator lights up when the unit receives a signal
from the remote controller.
Notes
•
•
•
Place the unit away from strong light such as direct sunlight or inverted
fluorescent light which can prevent proper operation of the remote con-
troller.
Using another remote controller of the same type in the same room or
using the unit near equipment which uses infrared rays may cause op-
erational interference.
Do not put any object such as a book on the remote controller. The but-
tons of the remote controller may be pressed by mistake and drain the
batteries.
Receiver
Remote control sensor
STANDBY indicator
•
•
Make sure the audio rack doors do not have colored glass. Placing the
unit behind such doors may prevent proper remote controller operation.
If there is any obstacle between the remote controller and the remote
control sensor, the remote controller will not operate.
30˚
30˚
approx. 16 feet
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio equipment connections
• Do not piug in the power cord until all connections have been made.
• On each pair of input jacks, a red connector (marked R) corresponds to the right
channel, and a white connector (marked L) to the left channel.
• Please refer to the instruction manual of each component when making any con-
nections.
Audio connection cable
L (Left)
L
R (Right)
R
• Insert the plugs and connectors securely. Remember that improper connection
can result in noise, poor performance, or damage to the equipment.
• Do not bind audio connection cables with power cords and speaker cables. Doing
so may degrade sound quality.
Improper Connection
Insert completely
:Signal Flow
1
Connect your player to COAXIAL or OP-
DIGITAL INPUT
TICAL, whichever appropriate.
COAXIAL
MD recorder / DAT etc...
1
OUTPUT
(COAXIAL)
Optial fiber cable
Coaxial cable
COAXIAL
2
DTR-7 / DTR-6
OPTICAL
1
Optial fiber cable
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
L
R
COAXIAL
2
OPTICAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
OUTPUT
(DIGITAL)
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
OPTICAL
SURROUND
(REC)
OUT
MONITOR
OUT
MULTI CHANNEL
INPUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
(PLAY)
CD
2
GND
VIDEO
PHONO
S
VIDEO
DIGITAL OUTPUT
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
CD player
DTR-7 only
Do not plug in the power
cord until all connections
have been made.
OUTPUT
(ANALOG)
(REC)
OUT
CD
TAPE
GND
Audio Connection Cable
IN
(PLAY)
PHONO
R
L
R
L
Audio Connection
Cable
OUTPUT
(PLAY)
INPUT
(REC)
Audio Connection
Cable
OUTPUT
Ground
Tape deck / MD recorder / DAT
3
Turntable
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio equipment connections
1. DIGITAL INPUT connectors
• If your CD player has a digital output connector, connect it to a proper DIGITAL INPUT connector for
clear and dynamic sound play.
Optical digital connector
• This unit provides four digital input connectors to connect CD players, MD recorders, DAT decks, etc.
having a digital output connector. When using these connectors, connect the unit also via the audio con-
nection cables. You should also note that the signals you can record are analog signals only.
• The digital inputs, COAXIAL 1, 2 and OPTICAL 1, 2 can be assigned to individual input selector buttons,
so when an input selector button is pressed, the assigned digital input is used instead of the corresponding
analog input. (See pages 23,29.)
Remove the protective
caps before making
connections. When not
in use, be sure to replace
them.
2. OPTICAL DIGITAL OUTPUT connector (DTR-7 only)
If you have a digital recorder, such as an MD recorder, DAT, and CD-R (Compact Disc Recorder), con-
nect the recorder’s digital input connector to this connector. In this case, always use commercially avail-
able optical digital audio cables.
3. Turntable
This receiver is designed for use with turntables using moving magnet cartridges.
Connect a ground (or earth) wire to GND terminal.
With some players, connecting a ground wire results in larger noise. If so, do not connect any ground wire.
AC outlet connection
You can connect the power cord from another
audio device to the rear of this receiver.
R
L
R
L
V
S
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
L
R
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
Since the AC outlets on the unit are
a
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
(REC)
OUT
MONITOR
OUT
MULTI CHANNEL
INPUT
R
L
SWITCHED type outlet, you can use the
STANDBY/ON button, to turn on/off the power
to both this receiver and the connected audio de-
vices.
TAPE
MULTI SOURCE
OUT
AC INLET
IN
(PLAY)
CD
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
First turn the POWER switch ON (
).
Make sure that the total capacity of other compo-
nents connected to this unit does not exceed the
capacity that is printed on the rear panel.
Capacity is total
120 watts.
Connections for remote control (z)
DTR-7 / DTR-6
You can use the remote controller of this receiver to operate
cassette tape decks and compact disc players that have Onkyo/
Integra z connectors.
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
L
R
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
R
L
VIDEO-3
DVD
FRONT
IN
Connect a remote control cable to the connector with the z
mark.
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
• An z remote control cable equipped with a 1/8 in. -diam-
eter miniature two-conductor phone plug comes with ev-
ery compact disc player or cassette tape deck that has an
z connector.
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
• Remote control operation is not possible if only the remote
control cable is connected – the audio connection cables
must also be connected.
CD Player
• This receiver’s remote controller does not support control
of Onkyo turntables.
• If the connecting device has two z connectors lined-up
vertically or horizontally, you can use either of them. They
both offer the same functionality.
• You can use the remote controller for the DTR-7/DTR-6 to
control an Onkyo/Integra DVD player or MD recorder that
is not connected via an z cable. When you control such a
DVD player or MD recorder, point the remote controller
toward the sensor area of the DVD player or MD recorder.
Cassette Tape Deck
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Video equipment connections
• On each pair of input jacks, the red connector (marked R) corresponds to the right channel, and the white connector (marked L)
to the left channel.
• The yellow connector (marked V) is used for video connection.
• Please refer to the instruction manual of each component when making any connections.
Audio connection cable
Video connection cable
L (Left)
L
R (Right)
R
Digital video equipment
or Video cassette recorder
Video Disc Player
:Signal flow
AUDIO
IN
VIDEO
IN
DIGITAL
OUT
AUDIO
OUT
VIDEO
OUT
AUDIO
OUT
VIDEO
PUT
2
R
L
V
S
OUT
IN
VIDEO-1
VIDEO-2
OUT
IN
VIDEO-3
DVD
IN
DIGITAL INPUT
1
R
L
R
L
V
S
DIGITAL INPUT
AMP IN
FRONT
OUT
COAXIAL
1
IN
ANTENNA
VIDEO-1
VIDEO-2
PRE OUT
FRONT
IN
COAXIAL
2
AM
COAXIAL
1
SUB
WOOFER
OUT
IN
OPTICAL
1
CENTER
SURROUND
OPTICAL
2
FM
75
MONITOR
OUT
VIDEO-3
DVD
FRONT
IN
IN
OPTICAL
SUB
WOOFER
DIGITAL OUTPUT
5
CENTER
AV RECEIVER
COAXIAL
2
SURROUND
MULTI CHANNEL
INPUT
MODEL NO. DTR-7
(REC)
OUT
MONITOR
OUT
V
S
R
L
TAPE
MULTI SOURCE
OUT
IN
(PLAY)
CD
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
OPTICAL
1
LOCAL REMOTE
VIDEO
DIGITAL COAXIAL
OUTPUT
4
S VIDEO
OSD SELECTOR
OPTICAL
2
OPTICAL
DIGITAL OUTPUT
DIGITAL
OPTICAL
OUTPUT
AUDIO
VIDEO
OUTPUT
OUTPUT
VIDEO IN
DVD player
3
Monitor TV
DTR-7 only
DTR-7/DTR-6
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
6
STANDBY MULTI SOURCE
POWER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DSP
MULTI SOURCE ANALOG
CH LEVEL
DIRECT
STEREO
/DTS
THX
SURROUND
MODE
Video camera etc.
VIDEO 4/VIDEO CAM INPUT
VIDEO4
(MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
C
D
S
VIDEO
VIDEO
L
AUDIO
R
DTR-7 by
( )
MONO
S
VIDEO
VIDEO
L
AUDIO
R
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Video equipment connections
1. Digital audio connections
This receiver has a powerful digital signal processor for use with DVD players, DAT decks, and CD players. The digital inputs, CO-
AXIAL 1, 2 and OPTICAL 1, 2 can be assigned to individual input selector buttons, so when an input selector button is pressed, the
assigned digital input is used instead of the corresponding analog input. (See page 23,29.)
2. Connect your second video cassette deck.
3. Connect your DVD player to COAXIAL or OPTICAL, whichever appropriate.
4. OSD SELECTOR:
Selects whether to output the OSD (On-Screen Display) information with the Video signals or the S-Video signals. Select "S VIDEO"
when the monitor is connected via the S-Video terminal.
5. Connecting video equipment through S-video connectors
• The signals input from the S IN jack will be output only to the S OUT jack; the signals input from the V IN jack will be output only to the
V OUT jack.
• For information on whether you need to connect either S or V jack or both of them, please refer to the instruction manual that came with
your video equipment.
6. Connect your video camera or TV game machine to the VIDEO-4 / VIDEO CAM INPUT jacks.
If a monaural video camera is used, connect its audio connection cable to “ R(MONO)” audio jack.
Notes:
•
When using a playback-only VCR, connect it to VIDEO 3 or VIDEO 4. If you connect it to VIDEO 1 or VIDEO 2, you need to make only the input
connections.
•
•
This receiver can be used only with a monitor TV equipped with a video input or S video jack.
Interference may be caused between the TV and this receiver. If this interference occurs, place the receiver and the TV as far apart as possible. We do not
recommend the use of a common TV/FM antenna (see antenna section).
•
Remove the protective cap attached to the DIGITAL INPUT/OUTPUT (OPTICAL) jack before making the connection. When this jack is not used,
replace the protective cap.
Connecting equipment with 5.1-channel output
Decoder with 5.1-channel output
You may connect the 5.1-channel outputs of an external decoder (such as MPEG decoder and DVD player) to the MULTI CHANNEL
INPUTs of this unit.
DVD player or a decoder with Multi (5.1) channel outputs
Multi (5.1) channel outputs
:Signal flow
Front
Subwoofer
Center
Surround
FRONT
FRONT OUT
SUB
WOOFER
SUBWOOFER OUT
CENTER OUT
CENTER
SURROUND
MULTI CHANNEL
INPUT
SURROUND OUT
R
L
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
AMP IN
R
R
L
V
S
OUT
IN
FRONT
COAXIAL
1
ANTENNA
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
R
COAXIAL
2
AM
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
DTR-7/DTR-6
AUDIO OUT
R
L
V
S
DVD
IN
VIDEO OUT
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting speakers
The DTR-7/6 allows you to connect two speaker systems.
Before connecting the speakers, place them correctly by consulting the instruction manuals that came with your speakers.
For surround playback (see “Using the listening modes” on page 34), the configuration and placement of your speakers are very important.
For Home THX cinema surround playback, we recommend that you use a THX speaker system that is certified by Lucasfilm Ltd. (such as
Onkyo HTS SYSTEM-2).
Ideal speaker configuration:
• Right and Left front speakers
• Center speaker
Minimum speaker configuration for surround sound playback:
• Right and Left front speakers
• Right and Left surround speakers
Produces a rich sound image by serving as a sound source for
the Right and Left front speakers and enhancing the sonic move-
ment.
• Right and Left surround speakers
Adds three-dimensional sonic movement and produces environ-
mental sound associated with the background and effect sound
for each scene.
The sound recorded for the center speaker and the subwoofer will be
properly distributed to the Right and Left front speakers and the
Right and Left surround speakers for optimized surround playback.
• Subwoofer
Produces powerful and heavy bass.
Speaker placement
Ideal speaker placement varies depending on the size of your room
and the wall coverings. Here, only typical example of speaker place-
ment and recommendations are shown.
1
3
4
2
5
Speaker systems
Left and Right front speakers and Center speaker
• Place these three speakers at the same height from the floor.
• Place each speaker so that sound is aimed at the audience's ears
at the listening position.
Left and Right surround speakers
• Place these speakers so that their height is 1 meter higher than
that of the audience's ears.
Subwoofer
To get the highest bass effect, place a subwoofer.
You can place your subwoofer anywhere in your room because the
placement affects very little the perceived sound.
6
7
8
1
2
3
4
5
6
7
8
TV or Screen
Front speaker Left
Subwoofer
Center speaker
Front speaker Right
Surround speaker Left
Surround speaker Right
Listening Position
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting speakers
• This receiver is designed to produce optimum sound quality when speakers with impedances within the specified ranges are connected.
Please check the following information and choose speakers with appropriate impedances for the connections.
FRONT SPEAKERS:
SURROUND SPEAKERS:
CENTER SPEAKER:
A or B: 6 ohms min./speaker
6 ohms min./speaker
6 ohms min.
• When you use only one
speaker or wish to listen to
monaural (mono) sound, a
single speaker should never
be connected in parallel to
both the right and left chan-
nel terminals simulta-
neously.
Connecting the speaker cable
No!
1. Twist wire ends very tight.
5/8"
+
–
–
+
+
–
–
+
R
L
R
L
2. Unscrew.
3. Insert wire.
4. Screw.
No!
Note:
To prevent damage to circuitry, never short-circuit
the positive (+) and negative (–) speaker wire.
Front Speaker A
L ch.
Front Speaker A
R ch.
SURROUND SPEAKERS
FRONT SPEAKERS A
R
R
L
R
L
CENTER
SPEAKER
L
Use Front SPEAKERS B termi-
nals to connect a second pair of
front speakers.
FRONT SPEAKERS B
Center Speaker
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
OUT
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
L
R
IN
OUT
IN
COAXIAL
2
SUB
WOOFER
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
DTR-7 / DTR-6
Surround Speaker
R ch.
Surround Speaker
L ch.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting speakers
Connecting a subwoofer
PRE OUT
FRONT
Use the PRE OUT SUBWOOFER jack to connect a subwoofer with
a built-in power amplifier. If your subwoofer does not have a built-
in amplifier, connect an amplifier to the PRE OUT SUBWOOFER
jack and the subwoofer to the amplifier.
SUB
WOOFER
CENTER
SURROUND
:Signal flow
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
L
R
L
V
S
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
L
R
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
Connecting power amplifiers
DTR-7
Connecting power amplifiers
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
Using auxiliary power amplifiers allows you to listen at louder vol-
umes than with the DTR-7/DTR-6 alone. If power amplifiers are
used, connect each speaker to the corresponding power amplifier.
When using speakers connected through external power amplifiers,
turn OFF the SPEAKERS A.
COAXIAL
1
VIDEO-1
PRE OUT
FRONT
COAXIAL
2
SUB
WOOFER
OPTICAL
1
CENTER
VIDEO-2
SURROUND
OPTICAL
2
VIDEO-3
DVD
FRONT
OPTICAL
SUB
WOOFER
DIGITAL OUTPUT
CENTER
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
DTR-7 / DTR-6
Notes:
SURROUND SPEAKERS
FRONT SPEAKERS
A
L
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
• Keep the jumper plugs so that you will not
lose them.
• When the connectors are not in use, replace
the jumper plugs.
PRE OUT
FRONT
R
R
L
R
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
(REC)
OUT
MONITOR
OUT
MULTI CHANNEL
INPUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
L
LOCAL REMOTE
REMOTE
CONTROL
Right front Speaker
Left front Speaker
R
L
PRE OUT
FRONT
SUB
WOOFER
Subwoofer
CENTER
SURROUND
Center Speaker
Left Surround Speaker
Right Surround Speaker
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an equalizer (DTR-7)
The AMP IN and the PRE OUT FRONT connectors are attached
DTR-7
with jumper plugs. When connecting an equalizer, remove these
jumper plugs before connecting the audio connection cables.
SURROUND SPEAKERS
FRONT SPEAKERS
A
DIGITAL INPUT
R
L
R
L
V
S
AMP IN
FRONT
OUT
COAXIAL
1
ANTENNA
VIDEO-1
PRE OUT
FRONT
R
L
R
L
IN
COAXIAL
2
AM
SUB
WOOFER
OUT
IN
1. Remove the jumper plugs.
CENTER
OPTICAL
1
SPEAKER
CENTER
VIDEO-2
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
See “Connecting power amplifiers.”
FM
75
R
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
2. Connect an equalizer.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
CD
(PLAY)
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
R
L
AMP IN
FRONT
Output jack
Input jack
PRE OUT
FRONT
Epualizer
Connecting the power
Connecting a power cable
R
L
R
L
V
S
SURROUND SPEAKERS
FRONT SPEAKERS
A
DIGITAL INPUT
AMP IN
FRONT
OUT
COAXIAL
1
ANTENNA
VIDEO-1
PRE OUT
FRONT
R
L
R
L
IN
COAXIAL
2
AM
SUB
WOOFER
OUT
OPTICAL
1
CENTER
SPEAKER
CENTER
VIDEO-2
1. Connect the outlet plug on the included power cable to the
AC INLET on the DTR-7/ DTR-6.
2. Plug-in the other end of the cable to a wall AC outlet.
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
IN
SURROUND
6
/
OPTICAL
2
FM
75
R
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
R
(REC)
OUT
MONITOR
OUT
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
(PLAY)
CD
GND
1
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
Notes:
•
Do not use any power cable other than the included cable. The included
cable is designed for use only with the DTR-7/ DTR-6. Do not use it for
any other device.
2
•
Do not connect or disconnect the outlet plug from the DTR-7/DTR-6
while the other end is plugged into the wall AC outlet.
2. STANDBY/ON button
STANDBY indicator
Connecting the power
1 POWER switch
• Before you turn on the receiver, confirm that all connections
have been made properly.
Display
• Turning on this receiver’s power may cause a momentary power
surge, which might interfere with other electrical equipment,
such as computers. If this happens, use a wall outlet on a differ-
ent circuit.
1. Press the POWER switch to set the receiver to Standby
mode.
MASTER VOLUME
FM MUTE/
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
BASS/
MODE
ADJUSTMENT
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
N
W
U
P
O
D
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
MULTI SOURCE ANALOG
A
SPEAKERS
PHONES
B
DISPLAY
DSP
CH LEVEL
DIRECT
STEREO
/DTS
THX
SURROUND
MODE
VIDEO4
(MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
C
D
S
VIDEO
VIDEO
L
AUDIO
R
The STANDBY indicator will light up.
2. Press the STANDBY/ON button to turn on the receiver. The
display will light up and the STANDBY indicator will be
turned off.
DTR-
7
by
If you press the STANDBY/ON button, the receiver returns to
Standby mode.
2. POWER STNBY
button
Turning the power on from the remote controller:
1. Press the MODE AUDIO button.
2. Press the POWER ON button to turn on the power to the
receiver, or press the POWER STNBY button to set the re-
ceiver in standby mode.
2. POWER ON
button
1. MODE AUDIO
button
• You cannot use the remote controller if the POWER switch on
the receiver is set to OFF.
• Set the volume level to minimum before you turn off the power
to the receiver.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Making antenna connections
Connecting the antenna cable to the 75/300 ohm
antenna adapter. (The antenna adapter must be
separately ordered.)
Outdoor
antenna
Indoor
antenna
Connecting the 300 ohm ribbon wire:
300 ohms
Loosen the screws and wrap the wire around these screws. Then
ribbon wire
tighten the screws with a screwdriver.
Connecting the coaxial cable:
1. With your fingernail or a small screwdriver, press the stoppers
outward and remove the cover.
2. Remove the transformer wire A from slit B and insert it into slit
1
2
3
C.
3. Prepare the coaxial cable as shown in the diagram.
Connect the 75/300 ohm antenna adapter to the coaxial cable.
6
3
6
mm mm mm
Slit B
15mm
1
2
Insert the end of the cable.
Clamp it in place with pliers.
4. Re-install the cover.
Wire A
Slit C
Directional Iinkage
Do not use the same antenna for both FM and TV (or VCR) recep-
tion since the FM and TV (or VCR) signals can interfere with each
other. If you must use a common FM/TV (or VCR) antenna, use a
directional linkage type splitter.
Directional linkage
type splitter
To TV (or VCR)
To receiver
Assembling the AM loop antenna
Assemble the loop antenna as shown in the illustration.
• Refer to the next page for details on connecting the AM loop
antenna.
Insert into the hole.
Connecting the antenna cable
1
2
3
1. Press down the lever.
2. Insert the wire into the hole.
3. Release the lever to replace it.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Making antenna connections
Connecting the included antennas
Connecting the FM indoor antenna:
The FM indoor antenna is for indoor use only. Extend the antenna
and move it in various directions until the clearest signal is received.
Fix it with push pins or similar implements in the position that will
cause the least amount of distortion.
ANTENNA
If the reception is not very clear with the attached FM indoor an-
AM
tenna, the use of an outdoor antenna is recommended.
FM
75
Connecting the AM loop antenna:
The AM loop antenna is for indoor use only. Set it in the direction
and position where you receive the clearest sound. Put it as far away
as possible from the unit, TVs, speaker cables, and power cords.
When reception is not satisfactory with the attached AM loop an-
tenna alone, connection of an outdoor antenna is recommended.
Remove the insulation at
the end of the cable, then
fully insert the stripped
end of the cable.
Connecting an FM outdoor antenna
Please make sure that you follow the considerations below regard-
ing the location.
Keep the antenna away from noise sources (neon signs, busy roads,
etc.).
It is dangerous to put the antenna close to power lines. Keep it well
away from power lines, transformers, etc.
ANTENNA
AM
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 19 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
FM
75
Connecting an AM outdoor antenna
The outdoor antenna will be more effective if it is stretched horizon-
tally above a window or outside.
Outdoor
antenna
ANTENNA
AM
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 19 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
FM
75
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the on-screen display
Using the OSD (on-screen display) function lets you display each
screen on your TV so that you can perform various settings using
only the remote controller.
1
How to use the on-screen display
1. Press the OSD MENU button.
The on-screen display appears.
2. Press the upper or lower edge of the ENTER/Cursor button
to select the item.
The items you can select on each screen are shown on the next
page.
3. Press the right edge of the ENTER/Cursor button to display
the setting screen.
2~4
On each screen, you can press the upper or lower edge of the
ENTER/Cursor button to select an item and then press the right
or left edge of the button to change the setting.
If the item has an additional screen, you can press the right edge
of the button to change to that screen.
4. Press the center of the ENTER/Cursor button.
Use either of the following methods to turn off the on-screen
display.
• Press the center of the ENTER/Cursor button.
By pressing this button, you can follow in reverse the sequence
in which you have displayed each setting screen. Finally, the on-
screen display disappears.
• Press the EXIT button.
The on-screen display disappears immediately.
Screen Setup
3
Use the on-screen display to set the background color, the superim-
pose mode, etc.
1. Press the OSD MENU button.
2. Select “Screen Setup” and press the right edge of the EN-
TER/Cursor button.
3. Press the upper or lower edge of the ENTER/Cursor button
** Screen Setup **
to select each item and then press the right or left edge of the
button to set a parameter.
Background
Background Color : Select the desired color from BLUE-1, BLUE-2,
GREEN-1, GREEN-2, MAGENTA, RED-1, and RED-2.
Superimpose Mode : Select one of the following:
OFF : The on-screen display appears on the selected background
color.
Color = Green 1
Superimpose
Mode = Normal
Immediate
Normal : The on-screen display is superimposed on images when
video signals are input and shown on the selected background color
when no video signal is input.
Display = ON
Character Position
Black : The on-screen display appears on black screen.
Immediate Display : Select either “ON” or “OFF.” When set to “ON,”
the screen will show for 3 seconds the result (or process) of the
operation every time you operate the unit. For example, the volume
level indicator appears on the screen when you increase the sound
volume.
Character Position : Using the ENTER/Cursor button, move the on-
screen display to the lower left, upper left, upper right, or lower
right of the TV screen.
4. Press the center of the ENTER/Cursor button, or press the
EXIT button.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the on-screen display
OSD screens
Input Selector screen (page 27,32)
** Input Selector **
Select the input source (page 27).
Input
= DVD
OPTICAL 1
Perform digital input setting (page 29).
Assign a video input source (page 40).
Perform IntelliVolume setting (page 43).
Digital Input Setup
Video Assign Setup
IntelliVolume Setup
Listening Dolby
Mode= Pro Logic
THX Cinema
Set the listening mode (page 36).
Rec Selector screen (page 45)
** Rec Selector **
•Picture
=DVD
VIDEO
1,2
•Sound
=DVD
TAPE
VIDEO
1,2
OPTICAL
OUT
Select the audio recording source (page 45).
•Digital
----
=
Listening Mode Setup screen (page 38)
*** Menu ***
** Listening Mode
Setup
Listening
Mode=Mono Movie
**
Input Selector
Rec Selector
Listening Mode Setup
Front Effect = ON
Reflect Level = 0dB
Reverb Level = 0dB
Speaker Setup
Screen Setup
Set the listening mode parameters
(pages 38,39).
Room Size
Default
=Mid
Speaker Setup screen (page 19)
** Speaker Setup **
Config Setup
Set the speaker configuration (page 19).
Set the speaker distance (page 20).
Set the speaker output level (page 21).
Set the bass peak level (page 23).
Distance Setup
Level Setup
Bass Peak Setup
or
Screen Setup screen (See the previous page.)
** Screen Setup **
Background
Set the background color.
Color = Green 1
Superimpose
Set the superimpose mode.
Mode = Normal
Immediate
Display = ON
Set the simultaneous display mode.
Set the display position of characters.
Character Position
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the speaker configuration
Perform this setup before using the unit.
SP/SYS SETUP button
SMART SCAN CONTROLLER
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
SMART SCAN
CONTROLLER
-
STAND BY
POWER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MU
R
L
E
TI
C
S
O
O
U
R
T
CE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
PHONES
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIO
by
R
DTR-
7
Setting the speaker configuration parameters
SP/SYS
SETUP
1
2
SPEAKERS
A
TUNED
AUTO
Using the SMART SCAN CONTROLLER, you can easily set the
speaker configuration. Turn it to select the parameter and press it to
go to the next item.
1. Press the SP/SYS SETUP button.
“Config Setup?” appears. Then Press the SMART SCAN CON-
TROLLER.
2. For the DTR-6, go to the next step.
For the DTR-7, “All Ch For THX” appears.
Set “Yes” or “No.”
Yes: Your system is a THX speaker system.
(The following steps are unnecessary.)
No : Your system is a non-THX speaker system.
Press the SMART SCAN CONTROLLER.
3. Set whether or not a subwoofer is connected.
Yes: A subwoofer is connected.
PRESET/MODE ADJ
PUSH TO ENTER
PRESET/MODE ADJ
DTR-7 only
SPEAKERS
A
TUNED
AUTO
No:
A subwoofer is NOT connected.
PUSH TO ENTER
Press the SMART SCAN CONTROLLER.
4. Select the size of your front speakers.
Large: Large front speakers are used.
PRESET/MODE ADJ
Small: Small front speakers are used.
Press the SMART SCAN CONTROLLER.
5. Select the size of your center speaker.
Large: A large center speaker is used.
PUSH TO ENTER
Small: A small center speaker is used.
None: A center speaker is NOT used.
Press the SMART SCAN CONTROLLER.
6. Select the size of your surround speakers.
Large: Large surround speakers are used.
Small: Small surround speakers are used.
None: Surround speakers are NOT used.
7. Press the SMART SCAN CONTROLLER.
This completes the speaker configuration setup.
3 ~ 6
PRESET/MODE ADJ
SPEAKERS
A
TUNED
FM STEREO AUTO
PUSH TO ENTER
Front
PRESET/MODE ADJ
Center
Surround
PUSH TO ENTER
PRESET/MODE ADJ
7
PUSH TO ENTER
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the speaker configuration
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Speaker Setup” and then press the right edge of the
3
** Speaker Setup **
Config Setup
ENTER/Cursor button.
3. Select “Config Setup” and then press the right edge of the
ENTER/Cursor button.
4. For the DTR-6, go to the next step.
Distance Setup
Level Setup
For the DTR-7, the display shows “All Channel For THX
Speakers.”
Select “Yes” and then press the center of the ENTER/Cursor
button. This sets all the connected speakers to THX
speakers.(The following steps are unnecessary.)
Select “No” and then press the center of the ENTER/Cursor but-
ton to go to the next step.
Bass Peak Setup
5. Press the upper or lower edge of the ENTER/Cursor button
to set each item and then press the right or left edge of the
button to set a parameter
4
Subwoofer: Set whether or not a subwoofer is connected.
* Config Setup *
Yes:
No:
A subwoofer is connected.
A subwoofer is NOT connected.
Front : Select the size of your front speakers.
Large: Large front speakers are used.
Small: Small front speakers are used.
Center : Select the size of your center speaker.
Large: A large center speaker is used.
Small: A small center speaker is used.
All Channel For
THX Speakers =No
None: A center speaker is NOT used.
Surround : Select the size of your surround speakers.
Large: Large surround speakers are used.
Small: Small surround speakers are used.
None: Surround speakers are NOT used.
5
6. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
* Config Setup *
Subwoofer =Yes
Front
Center
Surround
=Small
=Small
=Small
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the speaker distance
Setting the distance from each speaker to the
listening position
(Loudspeaker Position Time Synchronization*)
1
SP/SYS
SETUP
SPEAKERS
A
TUNED
AUTO
Select a value that is closest to the actual distance between each
speaker and the listening position.
Using the SMART SCAN CONTROLLER, you can easily set the
speaker configuration. Turn it to select the setting and press it to go
to the next item.
PRESET/MODE ADJ
For each speaker, you can set a distance of 0.3 meter to 9.0 meters
(or 1 foot to 30 feet) in increments of 30 cm (1 foot).
1. Press the SP/SYS SETUP button repeatedly until “Distance
Setup ?” appears.
PUSH TO ENTER
Press the SMART SCAN CONTROLLER.
2. “Left=” appears. Set the distance from the left front speaker.
Press the SMART SCAN CONTROLLER.
3. “Center=” appears. Set the distance from the center speaker.
Press the SMART SCAN CONTROLLER.
2 ~ 7
PRESET/MODE ADJ
SPEAKERS
TUNED
FM STEREO AUTO
A
PCM DIGITAL
ft
4. “Right=” appears. Set the distance from the Right front speaker.
Press the SMART SCAN CONTROLLER.
PUSH TO ENTER
5. “R-Sur=” appears. Set the distance from the Right surround
speaker.
PRESET/MODE ADJ
Press the SMART SCAN CONTROLLER.
6. “L-Sur=” appears Set the distance from the left surround
speaker.
Press the SMART SCAN CONTROLLER.
PUSH TO ENTER
PRESET/MODE ADJ
PUSH TO ENTER
7. “SW=” appears. Set the distance from the subwoofer.
8. Press the SMART SCAN CONTROLLER.
The speaker distance setup has been completed.
8
*
Loudspeaker Position Time Synchronization is
Lucasfilm LTD.
a
registered trademark of
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Speaker Setup” and then press the right edge of the
ENTER/Cursor button.
3. Select “Distance Setup” and then press the right edge of the
* Distance Setup *
ENTER/Cursor button.
You can now set the distance from each speaker.
(When the cursor is on “Right,” you can press the lower edge of
the ENTER/Cursor button to display additional items.)
Select a value that is closest to the actual distance. For each
speaker, you can set a distance of 0.3 meter to 9.0 meters (or 1
foot to 30 feet) in increments of 30 cm (1 foot).
Left =3.6m/12ft
Center =3.6m/12ft
Right =3.6m/12ft
(R-Sur =2.1m/ 7ft)
Left:
Left front speaker
Center speaker
Center:
Right:
R-Sur:
L-Sur:
Right front speaker
Right surround speaker
Left surround speaker
Subwoofer: Subwoofer
4. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the speaker Level
SP/SYS
SETUP
Using the test tone to adjust the speaker output
levels
1
SPEAKERS
A
DSP
1. Press the SP/SYS SETUP button repeatedly until
“Level Setup?” appears.
Press the SMART SCAN CONTROLLER.
PRESET/MODE ADJ
The display shows “Left.”
2. Rotate clockwise or counterclockwise the SMART SCAN
CONTROLLER to adjust the speaker output level.
You can adjust the output level of each speaker in the range of
12 to +12 dB, except for the subwoofer whose adjustment range
is -30 to +10 dB.
PUSH TO ENTER
Press the SMART SCAN CONTROLLER.
2
You hear a test tone (pink noise) from the left front speaker.
Each time you press the SMART SCAN CONTROLLER, the
speaker that produces a test tone changes as below. Set the out-
put level of each speaker by rotating the SMART SCAN CON-
TROLLER so that you can hear the same level of test tone at the
listening position.
PRESET/MODE ADJ
SPEAKERS
A
STEREO
PCM DIGITAL
db
PUSH TO ENTER
Left (Left front) Center (Center) Right (Right front) R-Sur (Right
surround) L-Sur(Left surround) Subwoofer (Subwoofer) Left
Center
PRESET/MODE ADJ
Notes:
Right
R-Sur
L-Sur
SW
• In order to correctly set the output levels, use a hand-held Sound
Pressure Level meter (SPL), set to C-Weighting and Slow aver-
aging.
2055) or equivalent can be used. Using the internal channel
noise generators, set each channel so that you read 75 dB SPL
from each channel.
• SPEAKER B, when selected, will be deselected automatically
as soon as the test tone starts sounding. The Test Tone function
is not available when the headphones are connected or when
MULTI CH INPUT is selected.
A
Radio Shack® SPL meter (catalogue number 330-
PUSH TO ENTER
• The test tone will not be output from the speaker that has been set
to "No" in the configuration setup explained on the page 18,19.
• If the speaker level is set to +1dB or higher , the maximum level
indicated on the display will change if you raise the volume level.
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Speaker Setup” and then press the right edge of the
* Level Setup *
ENTER/Cursor button.
3. Select “Level Setup” and then press the right edge of the
ENTER/Cursor button.
The Level Setup screen appears and a test tone (pink noise) is
output from the left front speaker. You can change the speaker
that outputs the test tone in the following sequence.(When the
cursor is on “Center,” you can press the lower edge of the EN-
TER/Cursor button to display additional items.)
Left
= +1dB
= 0dB
= 0dB)
Center
(Right
Left (Left front) Center (Center) Right (Right front) R-Sur (Right
surround) L-Sur (Left surround) Subwoofer (Subwoofer) Left.
4. Set the output level of each speaker so that you can hear the
same level of test tone in the listening position.
You can adjust the output level of each speaker in the range of -
12 to +12 dB, except for the subwoofer whose adjustment range
is -30 to +10 dB.
1
2
5. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
3
4
• Using Test button on the remote controller
1. Press the MODE AUDIO button.
2. Press the TEST button.
Left front speaker produces the test tone (pink noise).
3. To adjust the level of each speaker,press the CH SEL, but-
ton to select a speaker and press the LEVEL +/- buttons to
raise or lower the level.
4. Press rhe TEST button to complete adjustment.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Speaker level
Setting the bass peak level
(Bass Peak Level Manager* DTR-7 only)
SP/SYS
SETUP
1
SPEAKERS
A
DSP
To prevent damage to your subwoofer, you can set the bass peak
level the subwoofer can reproduce.
If your system does not include any subwoofer, this will set the bass
peak level your Front speakers can reproduce.
1. Press the SP/SYS SETUP button repeatedly until
“Bass Peak Setup?” appears. Then Press the SMART SCAN
CONTROLLER.
PRESET/MODE ADJ
“Limiter =”appears and you are now in the bass peak level set-
ting mode.
PUSH TO ENTER
2. Rotate the SMART SCAN CONTROLLER to select “Yes”
or “No.”
PRESET/MODE ADJ
2
If you select “Yes” and then press the SMART SCAN CON-
TROLLER, the display will show the current peak level fol-
lowed by “Test Tone ON?.”
SPEAKERS
A
3. Press the SMART SCAN CONTROLLER.
The test tone is output and “Turn SSC Up” appears.
4. Gently rotate the SMART SCAN CONTROLLER clockwise
and, just before sound is distorted, press the SMART SCAN
CONTROLLER.
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
If you do not press the SMART SCAN CONTROLLER, “Dis-
torts Push SSC” appears.
db
PUSH TO ENTER
Note:
SPEAKERS
A
• Allowing the speakers to produce distorted sound for a long
time may cause damage to the speakers.
• To disable the bass peak level limiter, select “No” in step 2.
*
Bass Peak Level Manager is a registered trademark of Lucasfilm LTD.
PRESET/MODE ADJ
3
4
SPEAKERS
A
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
db
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
PUSH TO ENTER
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Speaker level
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Speaker Setup” and then press the right edge of the
ENTER/Cursor button.
3
* Bass Peak Setup *
3. Select “Bass Peak Setup” and then press the right edge of the
Bass Peak Level
Limiter = Yes
ENTER/Cursor button.
The “Bass Peak Setup” screen appears.
Bass Peak Level Limiter :
Peak Level =+18dB
Enables (Yes) / Disables (No) the bass peak limiter.
The Peak Level indicates the bass peak level when the limiter
is set to Yes.
Starting
The Test Tone
4. Select “Starting The Test Tone” and then press the right
edge of the ENTER/Cursor button.
This generates a test signal and automatically sets the unit's
MASTER VOLUME control knob to -27 dB.
You can now press the right and left edges of the ENTER/Cur-
sor button to adjust the peak level in units of 1 dB.
5. Press the ENTER/Cursor button just before the sound is dis-
torted.
4
* Bass Peak Setup *
1.Turn Volume Up.
2.When Sound Distorts.
3.Press ENTER.
The bass peak level is stored and the Speaker Setup screen is
displayed again.
Level
-31dB
Playing a digital source (Digital Input Setup)
Digital input setup
2
DIGITAL/
ANALOG
Each of the DVD, CD, VIDEO 1-3, and TAPE input channels can be
set so that it accepts analog or digital audio input. The default setting
is below. Change the setting according to the connection.
SPEAKERS
A
STEREO
DIRECT
PCM DIGITAL
DVD:
OPT2
VIDEO1: COAX1
VIDEO2: – – – –
VIDEO3: COAX2
TAPE:
CD:
– – – –
OPT1
3
PRESET/MODE ADJ
Assume that you have connected a DVD player to the COAXIAL 1
connector.
1. Press the DVD input selector button.
2. Press the DIGITAL/ANALOG button until "Digital In-
put?" appears.
PUSH TO ENTER
3. Press the SMART SCAN CONTROLLER.
The digital input setup mode has been set.
PRESET/MODE ADJ
By rotating the SMART SCAN CONTROLLER, select the digi-
tal audio input connector “COAX 1,” from among “OPT 1,”
“OPT 2,” “COAX 1,” “COAX 2” and “– – – – .” Selecting
“– – – –”sets analog audio input.
PUSH TO ENTER
4. Press the SMART SCAN CONTROLLER.
This completes the digital input setup.
To select an input source using the on-screen display, follow steps 1
through 3 described on page 29.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting FM/AM radio stations
TUNING UP/DOWN
FM MUTE/MODE
CHARACTER/MEMORY
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
SMART SCAN
CONTROLLER
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIIOO
R
DTR-7 by
FM/AM
Tuning in a radio station
1
2
1. Press the FM or AM button.
2. Use the TUNING UP/DOWN buttons to change the fre-
SPEAKERS
A
SPEAKERS
quency.
FM
AM
A
UP................the frequency increases.
DOWN........ the frequency decreases.
• The frequency changes in 50 kHz steps in FM and 10 kHz in
AM each time you press the TUNING UP/DOWN button.
• In FM, if this button is held continuously for more than 0.5 sec-
onds,the frequencies are scanned automatically (FM auto tuning
mode).
When a broadcast is received, scanning stops.
DOWN TUNING
UP
SPEAKERS
A
DSP
TUNED
AUTO
Listening to a stereo radio station (FM mode)
When you tune in a stereo FM station, the FM STEREO indicator
lights up if the signal is sufficiently strong.
If the signal is weak, it may be impossible to tune in to the desired
station. In this case, tune in as follows.
FM MUTE/
MODE
Press the FM MUTE/MODE button. The AUTO indicator
turns off. At this time, the station will be in mono and interstation
noise will be heard. Select the station to which you want to listen.
DISPLAY button
Pressing the DISPLAY button each time will change the indication
as follows:
DISPLAY
Frequency (preset No.)
Listening mode
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting FM/AM radio stations
Programming radio stations
1
SPEAKERS
A
DSP
TUNED
AUTO
1. Select the frequency that you want to store in the memory.
(See Tuning in a radio station on page 24.)
2. Press the CHARACTER/MEMORY button.
“Preset In? ” appears.
3. Press the SMART SCAN CONTROLLER.
The “MEMORY” indicator lights up on the display.
4. Select the desired memory number using SMART SCAN
CONTROLLER.
5. Press the SMART SCAN CONTROLLER.
The received station will be stored in the specified preset num-
ber.
2
3
4
5
CHARACTER/
MEMORY
SPEAKERS
A
STEREO
AUTO
• A total of 40 stations can be stored in the memory.
PRESET/MODE ADJ
MEMORY
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
DSP
TUNED
AUTO
ch
PUSH TO ENTER
PRESET/MODE ADJ
PUSH TO ENTER
Cancelling preset stations
2
3
4
1. Select the preset station you wish to remove as explained in
the previous section.
CHARACTER/
MEMORY
SPEAKERS
A
STEREO
2. Press the CHARACTER/MEMORY button repeatedly.
“Preset Erase? ” appears on the display.
3. Press the SMART SCAN CONTROLLER.
“Erase OK ? ” appears.
To stop canceling preset stations, press the CHARACTER/
MEMORY button.
4. Press the SMART SCAN CONTROLLER.
PRESET/MODE ADJ
SPEAKERS
A
STEREO
PUSH TO ENTER
PRESET/MODE ADJ
PUSH TO ENTER
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
2. Make sure that the SPEAKERS A indicator is
lit on the display.
If it is not lit, press the SPEAKERS A button.
4. Adjust the sound volume to an appropriate level.
Rotating the MASTER VOLUME control knob clockwise in-
creases the sound volume.
Rotating the MASTER VOLUME control counterclockwise de-
creases the sound volume.
3 DIMMER
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIIOO
R
DTR-
7
by
4 PHONES
1. Press the desired input selector button or the MULTI CH INPUT button.
The selected source name appears on the display.
If you have selected DVD, CD, VIDEO 1, VIDEO 2, VIDEO 3, or TAPE, perform
“Digital Input Setup” (see page 23).
• See page 33 for information on MULTI CH INPUT.
• See page 32 if you have selected FM or AM.
3. Start playing the selected input source.
Note:
When you start playing the DVD player connected to the system, the mes-
sage may appear such as “PCM 48 kHz” before the current encode format
appears. This message is provided by the data from the DVD player, which
does not indicate any product failure.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
2. SP A
1 SLEEP
2 MODE AUDIO
4. VOLUME ∆/∇
1. INPUT SELECTOR
3 DIMMER
1 This button allows you to set the sleep timer.
(See page 31.)
2 Press this button to set the mode in which you can operate the
DTR-7/6.
3 Use this button to change the brightness of the display (normal
or dim).
4 You can connect stereo headphones to the PHONES jack using
If no sound is heard from the speakers, check the
following items:
• When you have selected DVD, CD, VIDEO 1- 3, or TAPE,
check the “digital input setup” is correct. (See page 23.)
• Make sure that the input signal format setting is correct. (See
page 28,29.)
• The Muting function may be activated. Cancel the Muting func-
tion. (See “Muting the sound” on page 31.)
• Make sure that SPEAKERS A is selected. (See “Selecting the
speaker system” on page 30.)
a standard stereo plug.
(When you connect headphones, the unit will enter STEREO
mode automatically and no sound will be heard from the speakers.)
Warning:
• Do not play CD-ROM discs that contain computer data as they
may damage the speakers when the sound is amplified by the
receiver.
• Selecting an input source using the on-screen
display
3
Instead of using the input selector buttons, you can use on-screen
display to select the desired input source.
1. Press the OSD MENU button.
2. Select “Input Selector” and then press the right edge of the
** Input Selector **
ENTER/Cursor button.
Input
= DVD
OPTICAL 1
3. Press the upper or lower edge of the ENTER/Cursor button
to select “Input” and then press the right or left edge of the
button to select an input source.
Digital Input Setup
Video Assign Setup
IntelliVolume Setup
Listening Dolby
Mode= Pro Logic
THX Cinema
• When you select DVD, CD, VIDEO 1- 3, or TAPE, set the
digital input parameters on the Digital Input Setup screen.
(See page 29.)
• When you have selected TUNER, the currently selected pre-
set number is displayed on the next line.
• See page 33 for information on MULTICH INPUT.
4. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
Setting the input signal format (Digital Input Setup)
1
The input signal format defaults to “Automatic.” Although you can
use this default setting normally, you may change it depending on
the input signal format.
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
Ex.) Setting the input signal format for DVD
1. Press the DVD input selector button.
2. Press the DIGITAL/ANALOG button twice to display the
digital input format.
2
DIGITAL/
ANALOG
SPEAKERS
A
TUNED
AUTO
Press the SMART SCAN CONTROLLER.
You are now able to select the input signal format.
3. By rotating the SMART SCAN CONTROLLER, select the
input signal format from among “Automatic,” “Digital,”
“Analog,” “PCM,” and “DTS.”
PRESET/MODE ADJ
Automatic (Automatic detection)
SPEAKERS
A
TUNED
AUTO
Input signal format (Dolby Digital, DTS, or PCM) used in the
selected input source is detected automatically to execute the
required decoding process. If no digital signal is input, the input
signals to the analog input jacks will be played.
PUSH TO ENTER
Digital (Digital input automatic detection)
PRESET/MODE ADJ
3
4
Input digital signal format (Dolby Digital, DTS, or PCM) used
in the selected digital input source is detected automatically to
execute the necessary decoding process.
SPEAKERS
A
TUNED
AUTO
Analog (Analog audio signal processing)
The audio signals input from the equipment connected to the
analog input jacks are played.
PUSH TO ENTER
PRESET/MODE ADJ
PCM (PCM signal processing)
A decoding process is executed only when PCM signals are in-
put.
DTS (DTS signal processing)
PUSH TO ENTER
A decoding process is executed only when DTS signals are in-
put.
Notes:
• In “Automatic” or “Digital” mode, if the CD or LD is fast-for-
warded during playback, decoded PCM signals may produce
skipped sound. In such cases, change the digital audio format to
“PCM.”
• If a CD or LD encoded in the DTS format is played back using
“PCM” or “Analog” mode, a noise will be produced. This noise
could damage the amplifier and speakers. Always use “Auto-
matic”, “Digital”, or “ DTS” mode when playing back DTS-en-
coded sources.
4. Press the SMART SCAN CONTROLLER.
This completes the digital audio format setup.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Input Selector” and then press the right edge of the
ENTER/Cursor button.
3. Select “Digital Input Setup” and then press the right edge of
* Digital Input Setup *
the ENTER/Cursor button.
The “Digital Input Setup” screen appears. To display VIDEO 2
and later items, press the lower edge of the ENTER/Cursor but-
ton.
• Select the digital input connector from among “OPTICAL 1,”
“OPTICAL 2,” “COAXIAL 1,” “COAXIAL 2,” and
“– – – –.”
CD
:COAXIAL 1
Automatic
:COAXIAL 2
Automatic
DVD
VIDEO 1 :----
Automatic
• If no digital input connector is assigned to the selected input
source, it will be indicated as “– – – –.”
• To enter the setting, move the cursor vertically using the EN-
TER/Cursor button.
4. To set the input signal format, move the cursor to the line
immediately below the input source and then press the right
or left edge of the ENTER/Cursor button.
• Select the digital audio format from among “Automatic,”
“Digital,” “Analog,” “PCM,” and “DTS.”
• Holding down the right or left edge of the ENTER/Cursor
button sequentially changes the setting.
5. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
Notes on DTS
1. If you play a CD or LD that supports DTS when the “Analog” or
“PCM” setting is selected on the DTR-7/DTR-6, the DTS en-
coded signal will not be decoded and noise will be output. This
noise could damage the amplifier and speakers. Therefore, be
sure to select “Automatic”, “Digital” or “DTS” and use the digi-
tal input jacks (OPTICAL1/2 /COAXIAL1/2) to connect the
DTS source.
2. If you play a CD or LD that supports DTS when the “Auto-
matic”, or “Digital” setting is selected, you may hear a noise for
a short while until the DTS decoder recognizes the DTS en-
coded signal and starts operating. This is not a malfunction.
3. If you press the PAUSE or SKIP button on the player while
playing a DTS source, a short noise may be heard. This is not a
malfunction. In such cases, try playing the source in the “DTS”
mode.
4. The DTS indicator on the DTR-7/DTR-6 lights up while it plays
the DTS source. When playback concludes and the DTS signal
transmission stops, the DTR-7/DTR-6 remains in DTS mode
and the DTS indicator remains lit. This prevents noise when you
operate the PAUSE or SKIP button on the player. Therefore, if
the source switches from the DTS signal to the PCM signal im-
mediately, the PCM signal may not be played. In this case, stop
the playback of the source on the player for about three seconds,
then resume playback.
5. Some CD players and LD players may be unable to play DTS
sources correctly even if you connect the player to the DTR-7/
DTR-6 digitally. This is because the digital signal has been pro-
cessed (such as the output level, sampling frequency, frequency
response, etc.), and the DTR-7/DTR-6 cannot recognize the sig-
nal as DTS data. Therefore, you may hear noise when you play a
DTS source while processing the signal.
6. The OUT jacks of the VIDEO-1, VIDEO-2, and TAPE connec-
tors output analog audio signals. Do not record CDs or LDs that
support DTS using these jacks. Otherwise, you will record a
DTS-encoded signal as noise.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
Selecting the speaker system
The DTR-7/DTR-6 can connect to two speaker systems. You can
switch between the two speaker systems by using the SPEAKERS A
and B buttons.
Selecting Speaker system A (SPEAKERS A indicator appears.)
Press the SPEAKERS A button to turn on or off the speakers con-
nected to the FRONT SPEAKERS A, CENTER SPEAKER and
SURROUND SPEAKERS terminals.
A SPEAKERS B
Selecting Speaker system B (SPEAKERS B indicator appears)
Press the SPEAKERS B button to turn on or off the speakers con-
nected to the FRONT SPEAKERS B terminals.
Notes:
• Be sure to select Speaker system A during surround playback or
when multi-channel input is enabled.
• Selecting Surround playback when both speaker systems are on
automatically turns off the speaker system B. Similarly, turning
on both speaker systems during Surround playback automati-
cally sets the listening mode to STEREO.
DISPLAY
Changing the display
The display changes each time you press the DISPLAY button dur-
ing playback.
FM/AM:
Preset station name
Frequency
Preset channel
Listening mode
(Does not appear if no name is given.)
SPEAKERS
A
DSP
TUNED
AUTO
SPEAKERS
A
DSP
TUNED
SPEAKERS
A
DSP
TUNED
AUTO
AUTO
ch
ch
Other sources:
Preset input source name
(Does not appear if no name is given.)
Listening mode
*
During Dolby Digital or DTS play-
back, the input signal format for the
playback software appears.
SPEAKERS
A
DSP
TUNED
SPEAKERS
A
DSP
TUNED
AUTO
AUTO
• For analog signals, “Input source name” or "Listening mode"
Input signal format:
can be selected.
• Current sampling frequency displays for PCM signals
(ex. “PCM 44.1 kHz”). No correct information displays, how-
ever, for the frequencies other than 32, 44.1, 48, and 96 kHz.
• “Input signal format” returns to “Listening mode” within
3 seconds.
• For Dolby Digital/DTS, the surround channels information may
also display. For example, “Dolby D 3/2” indicates that the
source outputs signals for three front channels and two surround
channels in Dolby Digital mode.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an input source
Muting the sound (Muting function, remote
controller only)
Use this function to turn off the playback sound immediately. For
example, you can use it when you receive a phone call when listen-
ing to music.
Remote controller
Press the MUTING button.
The display shows "Muting." Now the sound output to the speakers
and headphones stops.
Press the MUTING button again to turn on the sound output.
Note:
The Muting function will be canceled automatically if the receiver is
set in the standby mode.
Falling asleep with music (Sleep function,
remote controller only)
You can turn off the power to the DTR-7/DTR-6 automatically after
a specified time period.
1. Press the MODE AUDIO button.
Remote controller
2. Press the SLEEP button.
SPEAKERS
A
SLEEP
STEREO
The display shows “Sleep 90min,” which means the receiver
automatically enters the standby mode after 90 minutes.
3. Press the SLEEP button repeatedly until the desired sleep
time is displayed.
AUTO
Each time you press this button, the time decreases by 10 minutes.
To check how much time is left before the unit turns off...
Press the SLEEP button when the Sleep function is enabled.
Note:
Pressing the SLEEP button when the Sleep time display shows 10
minutes or less cancels the Sleep function.
Adjusting the tone (Bass and treble adjustment)
The bass and treble levels can be adjusted in the range of +/-12 in
units of 2.
You cannot perform this adjustment when the listening mode is
“THX” or “Direct.”
BASS/
TREBLE
1. Press the BASS/TREBLE button.
The display shows "Bass=."
Rotate the SMART SCAN CONTROLLER to adjust the bass
level.
2. Press the SMART SCAN CONTROLLER.
The display shows "Treble=."
Rotate the SMART SCAN CONTROLLER to adjust the treble
level.
3. Press the SMART SCAN CONTROLLER.
• Adjusting the bass and treble levels with the on-
screen display
4
1. Press the OSD MENU button.
2. Select "Listening mode Setup" and then press the right edge
of the ENTER/Cursor button.
3. Select "Listening Mode" and then press the right edge of the
ENTER/Cursor button
* Tone Control *
4. Select "Tone Control" and then press the right edge of the
ENTER/Cursor button.
The "Tone Control Setup" screen appears.
Press the upper or lower edge of the ENTER/Cursor button to
select "Bass" or "Treble" and then press the right or left edge of
the button to adjust the bass or treble level.
Bass = 0
Treble = +2
Set To Flat
Select “Set to Flat” and then press the right edge of the ENTER/
Cursor button to restore the “flat” bass and treble sound.
5. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
Note:
You cannot perform this adjustment when the listening mode is “Di-
rect” or “THX (DTR-7 only).”
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a preset station
2. Rotate the SMART SCAN CONTROLLER.
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIIOO
R
DTR-
7
by
1. Press the AM or FM button.
1. Press the MODE AUDIO button and then
the TUNER button.
2. Press the CH (+ or -) button to select the de-
sired preset number.
• Using the on-screen display
1. Press the OSD MENU button.
3,4
** Input Selector **
2. Select “Input Selector” and then press the right edge of the
ENTER/Cursor button.
3. Select “Input” and then press the right or left edge of the
ENTER/Cursor button to select “TUNER.”
4. Select “Preset No.” and then press the right edge of the EN-
TER/Cursor button
5. Press the right or left edge of the ENTER/Cursor button to
select the desired preset number.
6. Press the center of the ENTER/Cursor button, or press the
Input
= TUNER
Present No. =3
Video Assign Setup
IntelliVolume Setup
Listening
Mode= Orchestra
EXIT button. The on-screen display disappears.
5
* Preset Station *
Preset No. = 3
1:----
2:----
3:87.60
4:----
5:----
6: 531
7:----
8:----
9:----
10:----
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a multichannel input source
Setting the MULTI CHANNEL INPUT
1
To play back an input source you connected with the MULTI
CHANNEL INPUT connectors, you must set the output level of
each speaker. Also, note that this output level setting must be per-
formed independent of the speaker levels you set using the test tone
(see page 21).
Remote controller
MULTI CH INPUT
Before playing movie soundtracks etc. in the multichannel input
mode, check again that the source is connected properly
(see page 9).
1. Press the MULTI CH INPUT button.
If you wish to assign a video source to the multichannel input
source, perform the following setting. If you do not wish to do
so, proceed to step 3.
1. Press the SP/SYS SETUP button repeatedly until “Video As-
sign?” appears and then press the SMART SCAN CONTROL-
LER.
3
2. Rotate the SMART SCAN CONTROLLER to select the
video source you wish to assign and then press the SMART
SCAN CONTROLLER.
2. Start playing the component connected to the MULTI
CHANNEL INPUT connectors.
3. Press the CH SEL button on the remote controller to select
the speaker. Then, press the LEVEL (+ or -) button to adjust
the output level.
3
3
In the listening position, adjust the speaker output level so that
you can hear the same sound volume from all speakers. For the
right front, left front, center, right surround and left surround
speakers, the output levels can be adjusted within the range be-
tween -12dB/+12 dB. The adjustment range of the subwoofer,
however, is -30 to +10 dB.
Using the front panel
1. Press the CH LEVEL button.
2. Rotate the SMART SCAN CONTROLLER to select the output
level.
Repeat the above steps until you set the output levels for all
speakers.
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Input Selector” and press the right edge of the EN-
TER/Cursor button.
3. Press the right or left edge of the ENTER/Cursor button to
select “MULTI CH.” Then, press the center of the ENTER/
Cursor button.
6
** Multi Ch Input
**
Level Setup
Left
= 0dB
= +5dB
= 0dB
= 0dB
= 0dB
The “Multi Ch Input” screen appears.
Center
4. If you wish to skip assigning a video source, proceed to step 5.
To assign a video source, select “Video Assign Setup” and then
press the right edge of the ENTER/Cursor button. When “Video
Assign Setup” screen appears, move the cursor (which is already
located at “MULTI CH”) rightward or leftward to select the
video source you wish to assign. When selected, press the center
of the ENTER/Cursor button to return to the previous screen.
5. Select “Level Setup” and press the right edge of the ENTER/
Cursor button.
Right
Left Sur
Left Sur
Subwoofer
=+10dB
"Multi Ch Input Level Setup" screen appears.
6. Press the upper or lower edge of the ENTER/Cursor button
to select the item. Then, press the right or left edge of the
button to select the desired parameter.
In the listening position, adjust the speaker output level so that
you can hear the same sound volume from all speakers. For the
right front, left front, center, right surround and left surround
speakers, the output levels can be adjusted within the range of
-12 dB/+12 dB. The adjustment range of the subwoofer, how-
ever, is -30 to +10 dB.
7. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes
Before Using Listening Mode
STUDIO-MIX : This mode is suitable for rock and popular music.
Listening Modes
The DTR-7/DTR-6’s surround sound enables you to enjoy the pres-
ence of a movie theater or concert hall in your room.
Before using a listening mode, make sure the Speaker Setup param-
eters have been set (refer to page 18 ~ 23). Once the parameters have
been set, it is not necessary to set them again.
The configuration of the speakers are very important for the sur-
round sound. Refer to “connecting speakers” on page 10.
Lively sounds with a powerful acoustic image will make you
feel as if you are in a club.
5CH STEREO : This mode is useful for background music. The
front and surround channels will create a stereo image.
TV LOGIC : This mode offers a realistic acoustics of a TV pro-
gram being aired in the TV studio. It enhances the entire sur-
round sound and clarity of conversation.
DIRECT : This mode delivers pure sound with the minimum sound
quality adjustment and filtration. To attain it, the sound recorded
for the Right and Left front channels is output to the Right and
Left front speakers only and not output to the subwoofer.
STEREO
DOLBY DIGITAL Surround,
DTS (Digital Theater System)
This 5.1-channel digital surround format enables you to individu-
ally record and play five full-range (20Hz–20kHz) channels (left
and right front, center, two surround channels) plus an LFE channel
(Low Frequency Effect) for the low-range effect sound. It will cre-
ate a realistic sound that could be heard in the theaters and concert
halls.
Select this mode when you do not wish to use the surround
mode. All input sound is output from the front speakers.
DOLBY DIGITAL: Select this option when you play a DVD video
that has a
DTS: Select this option when you play a DVD player, video disc, or
CD that has a mark.
mark.
• A system with L/R front and center speakers
The following modes are available:
DOLBY 3 STEREO
DOLBY PRO LOGIC Surround
The surround channel sound is output from the left and right
front speakers.
STEREO
This is a normal stereo mode. Surround mode is cancelled.
DIRECT
See the description above.
This surround format consists of four channels (left and right front,
center, and monaural surround channels) and emphasizes the center
channel. This format is very effective for panning music, conversa-
tion, and three-dimensional sound movement output from three
front channels. It also simulates the atmosphere and surround ef-
fects of the sound reflected from the side and rear walls of the the-
ater. Select this option when you play a VHS, VHS Hi-Fi, laser
• A system with L/R front speakers
The following mode is available:
STEREO
disc, or DVD video that has a
mark.
Home THX Cinema Surround (DTR-7 only)
This is a normal stereo mode.
DIRECT
See the description above.
DOLBY DIGITAL/DTS/DOLBY PRO LOGIC/THX CINEMA
In these modes, Dolby Digital, Dolby Pro Logic or DTS Surround is
reprocessed using a technique called “Home THX processing.”
Home THX processing was developed by the surround engineers at
Lucasfilm Ltd. for accurate reproduction of soundfields in the home
environment as the filmmaker intended, equivalent to those ob-
tained in a well-furnished movie theater. For Home THX Cinema
Surround playback, we recommend that you use a THX speaker sys-
tem certified by Lucasfilm Ltd. (such as Onkyo's THX speaker sys-
tem HTS SYSTEM-2).
DSP (Digital Signal Processor)
The DSP converts the audio signals into digital audio format to cre-
ate sound reflection. This yields an effect that makes you feel like
listening to a live performance.
The following illustration shows how reflected sound reaches the
audience in a concert hall. Integra's DSP and advanced technologies
let you get such a sound reflection effect from the unit.
Surround modes incorporating Integra's original
Surround processing
Surround mode suitable for movie soundtracks
In the following surround modes, additional processing is applied to
the Dolby Digital, Dolby Pro Logic or DTS Surround.
ACTION
Suitable for movie soundtracks involving a lot of special effect
sounds.
Note:
The concert hall effect is produced from the reflections and rever-
berations contained in the original recording. These are converted
into reflected sound that is reproduced from four directions. Thus, in
some cases an unnatural impression can be conveyed if there are too
few reflections in the recording or if the effects in the original re-
cording were produced artificially.
MUSICAL
Suitable for musical film soundtracks, where importance is placed
on the music, environmental sound, and front image.
Example: Sound reflection in a concert hall
Integra’s listening modes
MONO MOVIE (DTR-7 only) : This mode is suitable for play
back monaural recordings such as old movie soundtracks. The
center channel delivers unprocessed original sound, whereas the
other channels delivers processed center-channel sound with ap-
propriate reverberation. Thus, you can enjoy monaural sound
with the atmosphere of a movie theater.
Ceiling reflections
Stage
reflections
Wall
reflections
ORCHESTRA : This mode is suitable for classics and opera music.
The center channel is cut and the surround channels are empha-
sized to widen the stereo image. It will simulate a natural rever-
beration that can be created in a large hall.
Direct sound
UNPLUGGED : This mode is suitable for acoustic instrumental
sounds, vocals, and jazz music. By emphasizing the front stereo
image, it will simulate the acoustics in front of the stage.
Wall reflections
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the listening modes
3. MASTER VOLUME
control knob
Use these buttons to set
the listening mode param-
eters. (See page 38.)
2. Use the LISTENING MODE buttons to select
the desired listening mode and then start play-
ing the selected source.
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIIOO
R
DTR-7 by
1. Press one of the INPUT SELECTOR buttons to select the desired
sound source.
1. Input selector buttons
Select the desired input source.
To change the input source using the remote controller,
press the MODE AUDIO button before pressing the input
selector button.
3. VOLUME buttons
Use these buttons to adjust the sound volume.
2. Listening mode button
Use these buttons to select the desired listening mode and
then start playing the selected source.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the listening modes
The LISTENING MODE button names on the unit may vary depending on
the model.
Using the listening modes
Pressing the DSP button and then rotating the SMART SCAN
CONTROLLER lets you view all the listening modes. You can se-
lect directly from four listening modes. The mode you can select
may vary depending on where the unit is purchased.
DTR-7
LISTENING MODE
DSP
DIRECT
STEREO
/DTS
THX
DIRECT : Press this button if you wish to enjoy pure direct
sound.
SURROUND
STEREO : Press this button to listen to a normal stereo audio.
/DTS : Press this button when you wish to play Dolby Pro
Logic, Dolby Digital, DTS Surround, software.
5CH STEREO(DTR-6) : Press this button to play 5-ch stereo
sound (see the previous page).
DTR-6
THX(DTR-7) : Press this button when THX speakers are used.
LISTENING MODE
Notes:
DSP
DIRECT
STEREO
/DTS
5CH STEREO
• To play a Dolby digital or DTS Surround source, you need to
connect the sound source with a correct digital input connector.
• When you play the Dolby digital or DTS Surround source, the
receiver automatically enters Dolby Digital Surround (stereo) or
DTS Surround (stereo) mode respectively.
SURROUND
THX
Movies which have been encoded in Dolby Digital, DTS, MPEG
and Dolby Pro Logic can all benefit by activating the THX mode.
THX should be activated only when watching movies which were
mixed for playback in large movie theatre environments. THX need
not be activated for music, movies that were made especially for
television or shows such as sports programming, talk shows, etc.
This is because they were mixed in a small room environment.
Dial norm
Dialogue Normalization (Dial Norm) is a feature of Dolby Digital.
When playing back software which has been encoded in Dolby
Digital, sometimes you may see a brief message in the front panel
display which will read Dial Norm XdB (X being a numeric value).
Dialogue Normalization serves to let you know if the source mate-
rial has been recorded at a higher or lower level than usual. For
example, if you see the following message: Dial Norm +4dB in the
front panel display, to keep the overall output level constant just
turn down the volume control by 4dB. In other words, the source
material that you are listening to has been recorded 4dB louder than
usual. If you do not see a message, then no adjustment of the volume
control is necessary.
•
Selecting an Listening mode using the on-screen
display
3
Instead of using the Listening mode buttons, you can use on-screen
display to select the desired input source.
1. Press the OSD MENU button.
2. Select “Input Selector” and then press the right edge of the
** Input Selector **
Input = DVD
ENTER/Cursor button.
3. Press the upper or lower edge of the ENTER/Cursor button
to select “Listening mode” and then press the right or left
edge of the button to select an listening mode.
4. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
OPTICAL 1
Digital Input Setup
Video Assign Setup
IntelliVolume Setup
Listening Dolby
Mode= Pro Logic
THX Cinema
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the listening modes
Input sources and listening modes
The available listening modes vary depending on the input source.
The following table shows each input source and the available listening modes.
*Available for DTR-6.
Input source
Listening mode
analog/PCM
Dolby Digital
DTS
MPEG
3/2ch
3/2ch
O
2/0ch
O
2/0ch
O
Stereo (3 Stereo)
Dolby Pro Logic
THX Cinema
Action
*
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Musical
Mono Movie
Orchestra
Unplugged
Studio-Mix
TV Logic
5ch stereo
Direct
Dolby Digital
THX Cinema
Action
*
*
*
*
*
*
*
O
O
O
O
O
O
O
O
O
Musical
Mono Movie
Orchestra
Unplugged
Studio-Mix
TV Logic
Dolby Digital Pro Logic *
Action
Musical
O
O
O
DTS
THX Cinema
Action
Musical
Mono Movie
Orchestra
Unplugged
Studio-Mix
TV Logic
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
• For Dolby Digital only typical input signals are shown here.
3/2ch, for example, means that the source outputs signals for three front channels and two surround channels.
The available listening modes vary depending on the input signal.
• The table shown above lists the input sources and listening modes available when the speakers are installed in a full configuration
(right/left front, center, and right/left surround speakers).Without surround speakers, set the listening mode to “STEREO (3 Stereo)” or
“Direct.”
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the listening mode parameters
How to set the listening mode parameters
LISTENING MODE
1
DSP
DIRECT
STEREO
/DTS
THX
To set the listening mode parameters, you first press the AUDIO
ADJUSTMENT button to select the item and then rotate the
SMART SCAN CONTROLLER to select the parameter.
1. Select the listening mode for which you wish set parameters.
2. Press the AUDIO ADJUSTMENT button until
“Frt Effect=...” appears.
SURROUND
2
3
AUDIO
ADJUSTMENT
SPEAKERS
DSP
The parameters you can set vary depending on the selected lis-
tening mode. You can press this button to display the available
parameters one by one.
A
3. Rotate the SMART SCAN CONTROLLER to change the
parameter setting.
4. Press the SMART SCAN CONTROLLER.
PRESET/MODE ADJ
PRESET/MODE ADJ
• Using the on-screen display
If you use the on-screen display to set a listening mode, you can set
the relevant parameters on the same screen.
PUSH TO ENTER
PUSH TO ENTER
1. Press the OSD MENU button.
2. Select the “Listening Mode” and press the right edge of the
ENTER/Cursor button.
3. Press the upper or lower edge of the ENTER/Cursor button
to select “Listening Mode.”
Then, press the right or left edge of the button to select the lis-
tening mode.
The parameter items available for the selected listening mode
are displayed.
** Listening Mode
Setup
**
Listening
Mode=Mono Movie
4. Press the upper or lower edge of the ENTER/Cursor button
to select the item and then press the right or left edge of the
button to set a value.
If you select “LFE Level,” “Setup,” etc., an additional screen
will appear. Set the value for each item in the similar manner.
5. Press the center of the ENTER/Cursor button, or the EXIT
RETURN button, to exit the setup mode.
Front Effect = ON
Reflect Level = 0dB
Reverb Level = 0dB
Room Size
Default
=Mid
Default: Select “Default” to reset each parameter to the factory-set
default.
Parameter
Re-EQ*
LateNight* LFE level* Front Effect* Reflect Level* Reverb Level Room Size
Listening mode
Stereo(3 Stereo)
Dolby Pro Logic
THX Cinema
Action/Musical
Mono Movie
Orchestra/Unplugged/
Studio-Mix/TV Logic
5ch Stereo
Direct
Dolby Digital
THX Cinema
Action/Musical
Mono Movie/Orchestra/
Unplugged/Studio-Mix/
TV Logic
*
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
*
*
*
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Dolby Digital Pro Logic
Action/Musical
DTS
*
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
THX Cinema
Action/Musical
Mono Movie/Orchestra/
Unplugged/Studio-Mix/
TV Logic
O
O
O
O
O
O
O
O
O
O
*Available for DTR-6.
(The detailed information on the listening mode parameters is provided on the next page.)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the listening mode parameters
Listening mode parameters
4. Adjust this parameter when the source is “DTS” and the lis-
tening mode is “DTS Orchestra,” “DTS Unplugged,” “DTS
Studio-Mix,” or “DTS TV Logic.”
• Re-EQ (Cinema Re-Equalization)
Select “ON” or “OFF.”
Select “-∞ dB,” “-10dB,” “0dB,” or “+10dB.”
The recommended setting is “+10dB.”
The Re-EQ function is effective except for “5CH STEREO” and
“DIRECT.”
Re-Equalization takes the edginess or “brightness” out of your
home cinema sound, compensating for the fact that sound mixed for
theaters will sound too bright when played back through speakers in
the home environment.
Note:
• The LFE level setting is effective only on Dolby Digital or DTS
software.
With some software, this setting may produce no effect.
• Front Effect
Select “ON” or “OFF.”
• Late Night
Select “High,” “Low,” or “OFF.”
Some live recordings contain acoustic reverberation. When you
play these sources, more reverberation will be applied by the DSP,
creating too much reverb effects and the sound loses its frame or
presence. In this case, set FRONT EFFECT to OFF. No reverbera-
tion from the DSP will be applied to the sound output from three
front channels, and the sound source will be played as it is without
any further reverberation.
Cinema sound has a vast dynamic range and therefore, to hear quiet
sound such as environmental sound and human conversations, it
must be played back at large sound volumes. When this parameter is
set to “High” or “Low,” however, the dynamic range of the sound is
narrowed down to allow you to hear easily minute sound at low vol-
umes. This function is useful if you wish to play a movie at low
volumes, especially in midnight.
Note:
Notes:
The Front Effect function is effective only on the Action, Musical,
MonoMovie, Orchestra, Unplugged, Studio-Mix, and TV Logic
sound.
• The depth of the Late Night effect is determined by Dolby Digi-
tal software. Some sounds may produce no or little effect.
• The Late Night function is effective only on Dolby Digital en-
coded software.
• Reflect Level
Set a value between -5 and +5 dB, in units of 1 dB.
• LFE (Low Frequency Effect) level
This parameter is used to adjust the level of LFE in Dolby Digital,
or DTS software. When this parameter is selected, the following
screen appears.
You can adjust the strength of direct sound reflection, depending on
the playback source material, your audio room conditions, and so
on.
• Reverb Level (DTR-7 only)
Set a value between -5 and +5 dB, in units of 1 dB.
* LFE Level Setup *
Adjust the depth of acoustic reverberation, depending on the play-
back source material, your audio room conditions, and so on.
Dolby Digital :0dB
DTS
:0dB
Cinema Group :0dB
Music Group :0dB
• Room Size (DTR-7 only)
Set “Large,” “Mid,” or “Small.”
Change the virtual hall size set for each surround mode.
1. Adjust this parameter when the source is “Dolby Digital.”
Select “-∞ dB,” “-20dB,” “-10dB,” “or “0dB.”
The recommended setting is “0dB.”
2. Adjust this parameter when the source is “DTS” and the
surround mode is “DTS.”
Select “-∞ dB,” “-20dB,” “0dB,” or “+10dB.”
The recommended setting is “+10dB.”
3. Adjust this parameter when the source is “DTS” and the lis-
tening mode is “DTS Action,” “DTS Musical,” “DTS THX,”
or “DTS Mono Movie.”
Select “-∞ dB,” “-20dB,” “-10dB,” or “0dB.”
The recommended setting is “0dB.”
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Assigning a video source to each audio
input source
Assigning a video source to each audio input
source (video Assign Setup)
1
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
You can assign a video source to audio input sources such as CD. By
doing so, you can play a CD or other audio source while showing the
assigned video images on the TV.
1. Select the desired audio input source by pressing the corre-
sponding input selector button.
2. Press the SP/SYS SETUP button repeatedly until "Video
Assign?" is displayed. Then Press the SMART SCAN CON-
TROLLER.
The video assign mode has been set.
3. Rotate the SMART SCAN CONTROLLER to select the
video source you wish to assign.
SP/SYS
SETUP
2
3
SPEAKERS
DSP
A
PRESET/MODE ADJ
You can select one from among 6 video sources: DVD, VIDEO
1, VIDEO 2, VIDEO 3, VIDEO 4, and ---- (None).
Press the SMART SCAN CONTROLLER.
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
DSP
PUSH TO ENTER
PRESET/MODE ADJ
PUSH TO ENTER
• Using the on-screen display
1. Press the OSD MENU button.
2. Select “Input Selector” and then press the right edge of the
* Video Assign Setup *
ENTER/Cursor button.
3. Select “Video Assign Setup” and then press the right edge of
the ENTER/Cursor button.
CD
:----
:----
:----
:----
:----
“Video Assign Setup” screen is displayed.
PHONO
FM
When the cursor is on “TAPE,” you can press the lower edge of
the ENTER/Cursor button to display additional items.
When the cursor is on “DVD,” you can press the upper edge of
the ENTER/Cursor button to display the previous items.
4. Press the upper or lower edge of the ENTER/Cursor button
to select the audio input source and then press the right or
left edge of the button to assign a video source.
You can select one from among 6 video sources: DVD, VIDEO
1, VIDEO 2, VIDEO 3, VIDEO 4, and ---- (None).
5. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
AM
TAPE
* Video Assign Setup *
DVD :DVD
VIDEO 1 :VIDEO 1
VIDEO 2 :VIDEO 2
VIDEO 3 :VIDEO 3
VIDEO 4 :VIDEO 4
MULTI CH:----
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Giving a name to each input source and preset
radio station
Giving a name to each input source
1
You can give a desired name to each input source (DVD, CD,
VIDEO 1-4, TAPE).
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
Characters available for name entry
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c
d e f g h i j k l m n o p q r s t u v w x y z ( ) < > [ ] & + - * / = ? !
: ; ’ ” . , 0 1 2 3 4 5 6 7 8 9_
( _ space)
2
3
CHARACTER/
MEMORY
SPEAKERS
STEREO
1. Select the source to which you wish to enter a name by press-
ing the corresponding input selector button.
2. Press the CHARACTER/MEMORY button.
“Name In ?” appears.
3. Press the SMART SCAN CONTROLLER.
Now you can enter a name.
4. Rotate the SMART SCAN CONTROLLER to select the
character you wish to enter and then press the SMART
SCAN CONTROLLER.
A
PCM DIGITAL
PRESET/MODE ADJ
5. Enter a name of up to 8 characters.
SPEAKERS
A
DSP
The name entry mode will be canceled automatically when you
finish entering 8 characters.
If you enter a name of shorter than 8 characters, press the
SMART SCAN CONTROLLER repeatedly until the initial dis-
play is restored.
PUSH TO ENTER
4,5
• To change a name...
PRESET/MODE ADJ
SPEAKERS
A
DSP
1. Select the source whose name you wish to change by pressing
the corresponding input selector button.
2. Press the CHARACTER/MEMORY button.
“Name In ?” appears.
PUSH TO ENTER
3. Press the SMART SCAN CONTROLLER.
Now you can change the name.
PRESET/MODE ADJ
4. Press the TUNING DOWN/UP button to select the character
you wish to change.
SPEAKERS
A
DSP
TUNED
AUTO
5. Rotate the SMART SCAN CONTROLLER to select the
character you wish to enter and then press the SMART
SCAN CONTROLLER.
PUSH TO ENTER
The name entry mode will be canceled automatically when you
finish entering 8 characters.
• To erase a name...
1. Select the source whose name you wish to erase by pressing
the corresponding input selector button.
2. Press the CHARACTER/MEMORY button twice.
“Name Erase ?” appears.
3. Press the SMART SCAN CONTROLLER.
“Erase OK ?” appears.
If the name cannot be erased, press the CHARACTER/
MEMORY button.
4. Press the SMART SCAN CONTROLLER.
The entire name has been erased.
Giving a name to each preset radio station
1
SPEAKERS
A
DSP
TUNED
You can give a desired name to each preset radio station.
AUTO
ch
1. Select the preset radio station to which you wish to enter a
name.
Then, follow steps 2 through 5 of the above procedure “Giving a
name to each input source” to give a name to each preset radio
station.
2 ~ 5
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the output level of each speaker
while listening to it
Fine-tuning the output level of each speaker
1
You can fine-tune the output level of each speaker according to your
taste.
CH LEVEL
The output levels you set as below will be lost once the unit is in stand-by
SPEAKERS
A
STEREO
PCM DIGITAL
mode. (The speaker levels you set using the test tone will be restored.)
1. Press the CH LEVEL button.
db
The output level of the Left front speaker is displayed.
2. Rotate the SMART SCAN CONTROLLER to select the out-
put level and then press the SMART SCAN CONTROL-
LER.
You can now adjust the output level of the center speaker.
3. Repeat the operation described in step 2.
Set the speaker level of each speaker in the following sequence:
Left (Left front) Center Right (Right front) R-sur (Right
surround) L-sur (Left surround) Subwoofer (Subwoofer)
You can adjust the output level of each speaker in the range of
-12 to +12 dB.
2.3
PRESET/MODE ADJ
PUSH TO ENTER
PRESET/MODE ADJ
The adjustment range of the subwoofer is -30 to +10 dB.
To use the above setting from now on...
The above setting will be overwritten by the speaker output levels you set
through the test tone, once you press the TEST button on the remote control-
ler.
PUSH TO ENTER
• Adjusting the output level of each speaker
using the remote controller
1. Press the MODE AUDIO button.
2. Press the CH SEL button repeatedly to select the speaker
whose output level you wish to fine-adjust.
Each time you press the CH SEL button, the output level of the
speaker displayed is changed in the following sequence:
Left (Left front) Center Right (Right front) R-sur (Right
surround) L-sur (Left surround) Subwoofer (Subwoofer)
3. Press the LEVEL + or - button repeatedly to fine-adjust the
output level.
1
2
You can adjust the output level of each speaker in the range of -
12 to +12 dB.
The adjustment range of the subwoofer is -30 to +10 dB.
3
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Other setup operations
SP/SYS
SETUP
Volume display method setup
SPEAKERS
DSP
A
1
You have the option of displaying your volume settings either of
two ways:
• ABSOLUTE — on a scale of MIN (0: no sound) to MAX (80:
PRESET/MODE ADJ
maximum volume);
2
or
• RELATIVE — on a scale which is measured “plus or minus,”
relative to the calibrated reference volume.
With either settings, the volume level changes in the same incre-
ment.
PUSH TO ENTER
PRESET/MODE ADJ
SPEAKERS
A
DSP
3
4
ABSOLUTE: MIN, 1, 2, 3, 4, ......., 77, 78, 79, MAX
RELATEVE: – , –61, –60, –59, ......., +16, +17, +18 (dB)
∞
1. Press the SP/SYS SETUP button repeatedly until “Volume
Display?” appears.
2. Press the SMART SCAN CONTROLLER.
Now you can change the sound volume display method.
3. Rotate the SMART SCAN CONTROLLER to select
“Absolute” or “Relative.”
PUSH TO ENTER
SPEAKERS
A
DSP
PRESET/MODE ADJ
4. Press the SMART SCAN CONTROLLER.
PUSH TO ENTER
IntelliVolume setup
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
1
2
The output level of each component or source connected to your
receiver varies, even when the sound volume setting is same. You
must therefore readjust the sound volume by yourself each time you
change the input source, because the same volume setting causes too
loud or too quiet sound. To prevent this inconvenience, you can set a
correction value for each level of input source in advance.
1. Select the source to which you wish to set IntelliVolume by
pressing the corresponding input selector button.
2. Press the SP/SYS SETUP button repeatedly until
“IntelliVolume?” appears. Press the SMART SCAN CON-
TROLLER.
SP/SYS
SETUP
SPEAKERS
A
STEREO
AUTO
PRESET/MODE ADJ
PUSH TO ENTER
Now you can perform IntelliVolume setup.
3. While listening to playback sound, rotate the SMART
SCAN CONTROLLER to select a desired value.
The setting is possible in the range between -12 / +12 dB,in units
of 1 dB.
PRESET/MODE ADJ
3
Press the SMART SCAN CONTROLLER.
PUSH TO ENTER
SPEAKERS
A
STEREO
AUTO
db
PRESET/MODE ADJ
PUSH TO ENTER
• Using the on-screen display
1. Press the OSD MENU button.
2. Select "Input Selector" and then press the right edge of the
ENTER/Cursor button.
3. Select "IntelliVolume Setup" and then press the right edge
* IntelliVolume Setup*
of the ENTER/Cursor button.
The IntelliVolume Setup screen appears. When the cursor is on
"TAPE," you can press the lower edge of the ENTER/Cursor
button to display additional items.
CD
:
:
:
:
:
0dB
0dB
0dB
0dB
0dB
PHONO
FM
4. Press the upper or lower edge of the ENTER/Cursor button
to select the input source and then press the right or left edge
of the button to select a value
AM
TAPE
Select a desired adjustment value for each input source. The set-
ting is possible in the range between -12 / +12 dB, in units of
1 dB.
5. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a source
SMART SCAN CONTROLLER
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIO
by
R
DTR-
7
Input selector buttons
REC OUT
Recording a source while listening to music or a
movie
1
2
1. Select the source you wish to play (recording source) by
pressing the corresponding input selector button.
See step 1 of “Selecting an input source” (page 26).
2. Press the REC OUT button.
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
The REC OUT indicator blinks for 8 seconds.
While the REC OUT indicator is blinking, rotate the SMART
SCAN CONTROLLER until "SOURCE" appears.
REC OUT
REC OUT
Notes:
•
For DTR-7, The digital input signals assigned to the input source you
selected using the input selector buttons will be output to the DIGITAL
OUTPUT terminal. There are some restrictions on digital recording.
When making digital recordings, consult the instruction manual that
came with your digital recording equipment (such as MD recorder or
DAT deck) to know what restrictions are imposed.
3
•
You cannot select the source connected to the MULTI CHANNEL IN-
PUT connectors. Even if you press the MULTI CH INPUT button in
step 1 above, the signals will be output to the L and R output jacks of the
input source you selected most recently.
PRESET/MODE ADJ
SPEAKERS REC OUT
A
STEREO
4. Start recording on the recorder connected to the TAPE,
VIDEO-1, VIDEO-2 jacks. Then, start playing the source
component you selected in step 1.
PUSH TO ENTER
Notes:
•
If you change the input source during recording, you will record the
signals from the newly selected input source.
•
You cannot record the surround effects.
Recording from on audio /video source
1
2
REC OUT
REC OUT
1. Press the REC OUT button
The REC OUT indicator binks for 8 seconds
2. While the REC OUT indicator is blinking, rotate the
SMART SCAN CONTROLLER to select the desired re-
cording source.
Notes:
PRESET/MODE ADJ
•
Selecting "SOURCE" sets the currently selected input source as the re-
cording source.
•
For DTR-7, The digital input signals assigned to the input source you
selected using the input selector buttons will be output to the DIGITAL
OUTPUT terminal. There are some restrictions on digital recording.
When making digital recordings, consult the instruction manual that
came with your digital recording equipment (such as MD recorder or
DAT deck) to know what restrictions are imposed.
PUSH TO ENTER
•
You cannot select the source connected to the MULTI CHANNEL IN-
PUT connectors. Even if you press the MULTI CH INPUT button in
step 1 above, the signals will be output to the L and R output jacks of the
input source you selected most recently.
3. Start recording on the recorder connected to the TAPE,
VIDEO-1, VIDEO-2 jacks. Then, start playing the source
component you selected in step 1.
Notes:
•
If you change the input source during recording, you will record the
signals from the newly selected input source.
•
You cannot record the surround effects.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a source
Adding sound to a video tape
HONO
CD
1
2
You can add CD or MD sound to your video recordings.
The following is an example of adding sound to a video recording
using the video cassette recorder connected to the VIDEO-1 jacks of
the receiver. Let's assume that you will record the images from a
video camera connected to the VIDEO-4 VIDEO jack and the sound
from a CD player.
SP/SYS
SETUP
SPEAKERS
A
DSP
1. Press the CD input selector button.
PRESET/MODE ADJ
2. Press the SP/SYS SETUP button repeatedly until “Video
Assign?” appears and then press the SMART SCAN CON-
TROLLER.
PUSH TO ENTER
3. Rotate the SMART SCAN CONTROLLER until "VIDEO
4" appears. Press the SMART SCAN CONTROLLER .
4. Insert a CD in the CD player. Or, insert a tape in the video
camera connected to the VIDEO-4 (VIDEO) jack.
5. Insert a tape to which recording is made in the video cassette
recorder connected to the VIDEO-1 (R, L, V) jacks.
6. Press the REC OUT button.
PRESET/MODE ADJ
3
SPEAKERS
A
DSP
PUSH TO ENTER
PRESET/MODE ADJ
The REC OUT indicator blinks for 8 seconds.
7. Rotate the SMART SCAN CONTROLLER to select
“SOURCE.”
PUSH TO ENTER
“CD” has been selected as the audio input source and “VIDEO
4,” which you set in steps 1 through 3, as the video input source.
8. Start recording on the video cassette recorder connected to
the VIDEO-1 jacks. Then, start playing the CD player and
the video camera connected to the VIDEO-4 jack.
4
5
6
Notes:
•
•
If you change the input source during recording, you will record the
audio signals from the newly selected input source and the video signals
assigned to that input source.
REC OUT
You cannot record the surround effects.
PRESET/MODE ADJ
7
8
SPEAKERS REC OUT
A
STEREO
PUSH TO ENTER
• Using the on-screen display
You can use the on-screen display to set the recording equipment to
which the signals are output. By doing so, you can record signals
from the selected input source.
** Rec Selector **
1. Press the OSD MENU button.
2. Select “Rec Selector” and press the right edge of the EN-
TER/Cursor button.
•Picture
=DVD
VIDEO
1,2
The Rec Selector screen appears.
The recording sources are shown on the left and the correspond-
ing output jacks are shown on the right.
3. Press the right or left edge of the ENTER/Cursor button to
•Sound
=DVD
TAPE
VIDEO
1,2
OPTICAL
OUT
select the output jack.
•Digital
When Sound is set to “TAPE,” “TUNER,” “PHONE,” or “CD,”
Picture shows the video source you set in “Assigning a video
source to each audio input source” (see page 40).
To record the currently playing sound or video images, select
“(SOURCE)” below the source name for Sound or Picture.
4. Press the center of the ENTER/Cursor button, or press the
EXIT button, to exit the setup mode.
----
=
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Multi-Room Remote System
Outline of Multi-room Remote System
If you connect Onkyo Multi-room Remote System components as shown in the figure below, you can control the components from a sub-
room as well as from the room where the DTR-7/DTR-6 is located. The Multi-Room Remote System allows remote operation when the A/V
system is mounted in a cabinet or rack.
The following equipment (sold separately) is essential for using the Onkyo Multi-Room System:
• Onkyo's Multi-Room System kits HKT-600 or HKT-700 (IR Remote Controller Extension System), or
• Multiroom A/V distribution and control systems from Niles® and Xantech® to name a few
Make connection as shown below. Do not plug the equipment into the power source until the connection is complete.
Enjoying Music and Movies in the Sub-room
DTR-7/DTR-6
3
speaker
speaker
Connection
L
R
L
V
S
SURROUND SPEAKERS
FRONT SPEAKERS
A
DIGITAL INPUT
R
AMP IN
FRONT
OUT
IN
example of Onkyo
Multi-room System
kit HKT-600
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
R
L
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
OPTICAL
1
TV
SPEAKER
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
MULTI CHANNEL
INPUT
(REC)
OUT
MONITOR
OUT
L
R
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
(PLAY)
CD
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
2
2
S-Video
conection
cable
MULTI SOURCE
OUT
Video connection cable
R
L
DTR-7 only
LOCAL REMOTE
L
+
+
-
L
R
-
R
1
Additional Amplifier
Audio connction cable
5
Mini Plug cable
Remote sensor HR-600
Remote contoroller
4
Power
supply
HB-100
Connecting block
: Signal flow
120V AC
(unswitched)
Main room
Sub room
1. Connect the receiver to the power amplifier.
2. Connect the sub-room speaker cables to the speaker terminals on the power amplifier.
3. Connect the receiver to the TV.(DTR-7 only)
4. Install the Connecting block in the main room, then connect it to the REMOTE jack on the receiver.
5. Install the remote sensor in the sub-room, then connect it to the connecting block in the main room.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Music and Movies in the Sub-room
To control the system in the sub-room
MULTI SOURCE indicator
SMART SCAN Controller
1. Press the POWER ON button on the remote controller.
The MULTI SOURCE indicator located below the STNDBY/
ON button on the receiver will light to indicate that the system
enters the Multi-Source mode.
MASTER VOLUME
FM MUTE/
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
MODE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
MULTI SOURCE
STANDBY MULTI SOURCE
POWER
PUSH TO ENTER
DIGITAL/
ON
OFF
Note:
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DSP
MULTI SOURCE ANALOG
CH LEVEL
DIRECT
STEREO
/DTS
THX
SURROUND
MODE
If you operate the system in the sub-room while a recording is going on in
the main-room, the source of the recording switches to the source which you
are playing in the main room. Be careful when you are recording a different
source from the one that you are playing.
VIDEO4
(MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
C
D
S
VIDEO
VIDEO
L
AUDIO R
DTR-
7
by
REC OUT/MULTI SOURCE
2. Press the appropiate Input Selector button on the remote
controller to select your desired source and start operating
it.
3. Adjust the volume on the power amplifier to the desired
level.
1. POWER ON
To control the system using the main unit
(e.g. when no remote controller is available):
1. Press the REC OUT/MULTI SOURCE button on the system
to make sure the MULTI SOURCE indicator flashes in the
display window.
2. Making sure that the indicator flashes, select a source by us-
ing the Smart Scan Controller.
Adjust the volume in the sub-room.
Notes:
•
In the sub-room, you can only play the source in the 2-Channel mode.
You cannot play the source in the Multi-Channel mode or the Surround
mode.
2. Input Selector
•
If you press the REC OUT/MULTI SOURCE button in the main room
while you are playing the source in the Multi Source mode in the sub-
room, the Multi Source function will be deactivated and the source will
be inaudible in the sub-room.
•
Please note that some third-party multi-room system components may
not be fully compatible with the Onkyo multi-room system components.
When the system is mounted in a rack:
To enable remote operation when the receiver is mounted in a rack
which will not permit infrared beams to pass, install the remote sen-
sor at a location outside of the rack where the infrared beams from
the controller can reach.
DTR-7/DTR-6
1. Connect the LOCAL jack (on the rear of the receiver) to the
connecting block.
2. Install the remote sensor at a location where it can detect the
infrared beams from the remote controller. Then, connect
the remote sensor to the connecting block.
R
L
R
L
V
S
SURROUND SPEAKERS
FRONT SPEAKERS
A
DIGITAL INPUT
AMP IN
FRONT
OUT
IN
COAXIAL
1
ANTENNA
AM
VIDEO-1
VIDEO-2
PRE OUT
FRONT
R
R
L
R
L
COAXIAL
2
SUB
WOOFER
OUT
IN
CENTER
SPEAKER
OPTICAL
1
CENTER
CAUTION: SPEAKER IMPEDANCE
OHMS MIN. SPEAKER
SURROUND
6
/
OPTICAL
2
FM
75
L
VIDEO-3
DVD
FRONT
IN
OPTICAL
SUB
WOOFER
AC OUTLETS
AC 120V 60Hz
SWITCHED
FRONT SPEAKERS
B
DIGITAL OUTPUT
IN
CENTER
AV RECEIVER
MODEL NO. DTR-7
TOTAL 120W 1A MAX.
SURROUND
(REC)
OUT
MONITOR
OUT
MULTI CHANNEL
INPUT
R
L
TAPE
MULTI SOURCE
OUT
AC INLET
IN
(PLAY)
CD
GND
VIDEO
PHONO
S
VIDEO
OSD SELECTOR
R
L
R
L
LOCAL REMOTE
REMOTE
CONTROL
1
Power
supply
HB-100
Connecting block
2
LOCAL REMOTE
Remote sensor HR-600
Remote contoroller
Mini Plug cable
120V AC
(unswitched)
In the rack
Outside of the rack
47
Download from Www.Somanuals.com. All Manuals Search And Download.
The initial settings
The following table shows the factory-set default parameter values. Use it as a reference when you change these parameter values as needed,
although they are usable in many cases.
Initial settings
Config Setup
Digital input
All Ch For THX
Yes
DVD
OPT2
When set to “No”
Subwoofer
Front
VIDEO1
VIDEO2
VIDEO3
VIDEO4
TAPE
COAX1
—(None)
COAX2
—(None)
—(None)
OPT1
Yes
Small
Small
Small
Center
Surround
CD
Distance Setup
Left
Center
Right
R-Sur
L-Sur
Intellivolume
CD
PHONO
FM
AM
TAPE
3.6m/12ft
3.6m/12ft
3.6m/12ft
2.1m/7ft
2.1m/7ft
3.6m/12ft
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
Subwoofer
DVD
VIDEO1
VIDEO2
VIDEO3
VIDEO4
Speaker Level (Test tone)
Left
0dB
Center
Right
R-Sur
L-Sur
Subwoofer
0dB
0dB
0dB
0dB
0dB
Video assign Setup
CD
PHONO
FM
AM
TAPE
DVD
—(None)
—(None)
—(None)
—(None)
—(None)
DVD
Listening mode
Listening mode
stereo
VIDEO1
VIDEO2
VIDEO3
VIDEO4
VIDEO1
VIDEO2
VIDEO3
VIDEO4
Listening mode parameter
Re-EQ
ON when “THX” is selected
OFF when “THX” is NOT selected
LATE NIGHT
LFE level
Front Effect
Reflect level
Reverb level
Room size
OFF
0dB
ON
0dB
0dB
Mid
Tone Control
bass
treble
0
0
Screen Setup
Background color
Superimpose
Multi ch input
Left
Center
Right
R-Sur
L-Sur
Blue1
Normal
ON
0dB
0dB
0dB
0dB
0dB
0dB
Immediatedisplay
Subwoofer
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote controller
Overview
When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press
the operation buttons. For example, if you wish to control the receiver from a remote controller, first press the MODE AUDIO button, then
press an appropriate operation button. To control a CD player, press the MODE CD button, then press an appropriate operation button.
First, press the desired MODE button to make sure that the receiver is set to a correct mode.
Using the RC-392M to control each device
Turning the power on and off to the receiver
Note:
SEND/LEARN
indicator
Before operating the RC-392M, turn on the POWER switch on the
the receiver so that the unit enters standby mode.
1. Press the MODE AUDIO button.
POWER
STNBY
2. Press the POWER ON button.
POWER ON
Pressing the POWER STNBY button will activate the power
standby mode.
SEND/LEARN indicator
This indicator acts as a guide when commands are programmed
into or sent by the remote controller. It also warns the user when
an error is made or battery power is low.
MODE AUDIO
Controlling the receiver
1. Press the MODE AUDIO button.
2. Press the desired operation button.
Shaded buttons in the figure are the operation buttons used
to control the receiver.
POWER
ON/STNBY
SLEEP
POWER ON/STNBY
: Power on/standby
: Sleep function
SLEEP
LIGHT
DISPLAY
VOL ∆/∇
CH +/-
: Changing the display
: Adjusting the volume
: Tuner preset number increment/decrement
MODE
AUDIO
INPUT SELECTOR
DISPLAY
Listening mode
: Changing Listening mode
SP A/SP B : Switching between Speakers A and B
CH +/–
VOL
CH SEL
DIMMER
: Selecting a speaker
: Adjusting the brightness of the display
TEST
MUTING
LEVEL +/- : Adjusting the speaker levels
TEST
MUTING
LIGHT
: Test tone
: Muting
: Illuminating the buttons.
INPUT
SELECTOR
Listening
mode
SP A/B
LEVEL +/–
DIMMER
CH SEL
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote controller
Controlling an Onkyo/Integra CD player
Note:
First connect an Onkyo/Integra CD player using the zconnection.
(See page 7.)
1. Press the MODE CD button.
2. Press the desired CD operation button.
TRACK
: Selecting a track
MODE CD
DISC
: Selecting a disc in the CD changer
: Down
: Up
: Playback
: Stop
: Rewind
: Fast forward
: Pause
CD
operation
buttons
EJECT r
: Eject
0, 1~9, +10 : Numeric keys
You may also use the following buttons:
VOL ∆/∇
MUTING
: Adjusting the volume level of the receiver
: Muting the sound from the receiver
Numeric keys
Controlling an Onkyo/Integra DVD player
Note:
Make sure that you point the transmission part on the remote con-
troller toward the sensor area on the DVD player.
1. Press the MODE DVD button.
2. Press the desired DVD operation button.
POWER ON/STNBY
POWER
ON/STNBY
: Turning the power on and off to the DVD
player
: DVD setup
DVD SET
MODE DVD
DVD player on-screen button
DVD SET
MENU
MENU
: Displaying the menu
: Moving the cursor
ENTER
RETURN
: Confirming the selection
: Return
DVD player buttons
: Down
: Up
: Playback
: Stop
DVD
operation
buttons
: Rewind
: Fast forward
: Pause
EJECT r
: Eject
0, 1~9, +10 : Numeric keys
ENT : Confirm
You may also use the following buttons:
Numeric keys,
ENT button
VOL ∆/∇
MUTING
: Adjusting the volume level of the receiver
: Muting the sound from the receiver
Note:
The ENT button on the right below the numeric keys has the same
function as “ENTER” of the ENTER/cursor button.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote controller
Controlling an Onkyo/Integra MD recorder
Note:
Make sure that you point the transmission part on the remote con-
troller toward the sensor area on the MD recorder.
1. Press the MODE MD/AUX button.
2. Press the desired MD operation button.
Turning the power on and off to the MD recorder
POWER ON/STNBY
MODE MD
: Turning on or standby the power to the MD
recorder
: Down
: Up
: Playback
: Stop
: Rewind
: Fast forward
MD
operation
buttons
REC o
: Record
: Pause
EJECT r
1~9, +10
ENT
: Eject
: Numeric keys
: Confirm
Numeric keys,
ENT button
You may also use the following buttons:
VOL ∆/∇
MUTING
: Adjusting the volume level of the receiver
: Muting the sound from the receiver
Controlling an Onkyo/Integra tape deck
MODE
AUDIO/TAPE
Note:
First connect an Onkyo/Integra tape deck using the zconnection.
(See page 7.)
1. Press the MODE AUDIO/TAPE button.
2. Press the desired tape deck operation button.
: Playback
: Stop
: Rewind
: Fast forward
TAPE
operation
buttons
REC o
: Recording/pause
: Reverse playback
You may also use the following buttons:
VOL ∆/∇
MUTING
: Adjusting the volume level of the receiver
: Muting the sound from the receiver
MODE SAT, CABLE, VCR, and TV buttons
No preset codes are programmed into the MODE SAT, CABLE,
VCR, and TV buttons. You can use these buttons to program remote
controller signals of other devices. (See page 52.)
MODE SAT,
CABLE,VCR,
TV
You may use the following buttons:
VOL ∆/∇
MUTING
: Adjusting the volume level of the receiver
: Muting the sound from the receiver
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the remote controller codes
of other devices into the RC-392M
The RC-392M has two learning functions. One is a normal learning function that enables the RC-392M to learn other remote controllers’
codes. The other is a macro learning function, which enables the RC-392M to learn a series of codes already memorized in the remote
controller into one MACRO button.
Programming procedure
Any button is programmable except for the eight Mode buttons
(AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV), two
4
R C - 3 8 5 S
Macro buttons (DIRECT and MODE), and LIGHT button.
V O L U M E
M U T I N G
T O N E
T E S T
L E V E L
R E M O T E C O N T R O L L E R
C H S E L
C
P E T
T U N E R
D V D
T A P E
I N P U T
M U L T I - C H
P H O N O
G R O U P
M O D E
S U R
D I S C
T U N E R
C
D
2
V I D E O - 2
I N P U T E C T O R
T A P E
Light
D I M M E R
V I D E O - 1
S L E E P
D V
P O W E R
1
3
5 to 15 cm
(2 to 6 inches)
RC-392M
1. Place the RC-392M and the remote controller for another
device, with 5–15cm (2–6 inches) apart and the light-emit-
ting parts facing each other.
2. While pressing and holding down the desired MODE button
on the RC-392M (AUDIO, CD, DVD, MD, SAT, CABLE,
VCR, or TV), press the ENT button, then release the but-
tons.
Notes:
•
The remote controller can have max 408 memory slots (51 buttons by 8
modes), although this number varies significantly depending on the
manufacturers and types of the remote controller you wish to program
into the RC-392M. It is recommended that you determine which button
functions have priority for programming.
•
If you do not press any button for more than 30 seconds during the pro-
cedure, the SEND/LEARN indicator flashes three times quickly, then
the RC-392M exits Learning mode. Resume from Step 2.
If you make a mistake during programming, the SEND/LEARN indica-
tor flashes three times quickly, then the RC-392M exits Learning mode.
If you try to program beyond the learning capacity of the RC-392M, the
SEND/LEARN indicator flashes six times quickly, then the RC-392M
exits Learning function. Try programming in a button of other MODE.
Follow the same procedure when you wish to program new codes into
the already-programmed buttons.
When you press and hold down one of the MODE button, the
SEND/LEARN indicator lights up. When you press the ENT
button, the indicator turns off. When you release the buttons, the
SEND/LEARN indicator lights up again.
•
•
3. Press and release the desired operation button on the RC-
392M.
You may select any button within the rectangle shown in the
figure. When you press the button, the SEND/LEARN indicator
turns off. When you release the button, the indicator lights up
again.
•
•
This remote controller uses infrared rays. Most remote controller codes
can be memorized using the infrared system; however, depending on
the degree to which the system differs, there may be some rare occa-
sions when memorization is not possible.
4. Press and hold down the desired button on the remote con-
troller of the other device until the SEND/LEARN indicator
on the RC-392M flashes twice.
The SEND/LEARN indicator flashes twice slowly, then lights
up.
5. Repeat Steps 3 and 4 to program other buttons in the same
•
Some remote controllers use a single button to perform different func-
tions, with the function code changing each time the button is pressed. If
you are using this kind of controller, please perform the “learn” opera-
tions for each function individually to store each function to a button on
the RC-392M.
For instructions regarding the operation of “learned” units, please refer
to the instruction manual for each product.
Even after codes have been memorized, please keep your old remote
controller in a safe place. If the memorized codes are lost when the bat-
teries run down, it will be necessary to memorize them once again using
the old remote controller.
Make sure both the RC-392M and the product’s own remote controller
have fresh batteries. If either of them has batteries that are wearing
down, it may be impossible to store the remote controller codes into the
RC-392M or the product may not respond properly to the buttons on the
RC-392M for which the remote controller codes were stored into
memory.
MODE.
Repeat Steps 2-4 to program other buttons in a different MODE.
6. Press the MODE button to complete programming.
7. Operate the programmed button to make sure the learning
function works.
•
•
Note:
The remote controller codes for the Onkyo/Integra CD player,
tape deck, DVD player, and MD recorder have already been
programmed into the buttons on the RC-392M. You may pro-
gram other remote controller codes into these buttons. If you
wish to restore the Onkyo/Integra preset codes after you pro-
gram new codes, erase the new codes. (See page 53.)
•
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the remote controller codes of other devices into the RC-392M
See page 57 for information on how to erase the learned codes from all buttons.
Erasing a learned code
SEND/LEARN
indicator
You can erase a learned code. You cannot erase preset codes.
•Erasing a code programmed in a button
1. Press and hold down the corresponding MODE button and
press the ENT button, then release the buttons.
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the ENT button, the indicator
turns off. When you release the buttons, the indicator lights up
MODE
buttons
again.
2. Press and release the button from which you wish to erase
the learned code.
When you press the button, the SEND/LEARN indicator turns
off. When you release the button, the indicator lights up again.
3. Press and release the same button again.
The SEND/LEARN indicator flashes twice slowly. The learned
code is erased.
Note:
If you do not press the button in step 2 or 3 for more than 30 sec-
onds, the SEND/LEARN indicator flashes three times quickly, then
the RC-392M exits Learning mode. Resume from Step 1.
ENT
Erasing a learned code from a MODE button
SEND/LEARN
indicator
1. Press and hold down the MODE button from which you
wish to erase the learned code, and press the ENT button
twice. Then release the buttons.
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the ENT button, the indicator
turns off. When you release the buttons, the indicator flashes
MODE
buttons
twice slowly, then lights up again.
2. Press and release the same MODE button again.
When you release the button, the SEND/LEARN indicator
flashes twice slowly. The learned code is erased.
Note:
•
•
•
If you do not press any button for more than 30 seconds, the SEND/
LEARN indicator flashes three times quickly, then the RC-392M exits
Learning mode. Resume from Step 1.
If you make a mistake during programming, the SEND/LEARN indica-
tor flashes three times quickly, the RC-392M exits Learning mode. Re-
sume from Step 1.
If you have programmed many button operations to a single MODE but-
ton, the SEND/LEARN indicator may remain illuminated continuously
in Step 2. This is not malfunction.
ENT
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Macro function
What is a Macro function?
A Macro function enables you to program a series of button operations into a single button on the remote controller. For example, you need
to follow the steps below to play a CD player connected to the receiver without using the Macro function:
1: Press the MODE AUDIO button. → 2: Press the POWER ON button. → 3: Press the CD (INPUT SELECTOR) button. → 4: Press the
MODE CD button. → 5: Use the numeric keys to select the desired song.
This operation will be two button presses away if you program these steps into a macro button.
Programming Macro mode
You may program the desired steps into each of eight MODE but-
tons. The following example explains how to program Steps 1–5
(described above) into the MACRO MODE button under the
MODE CD button (CD mode).
2
1. Press and hold down the desired MODE button you wish to
program (in this case, MODE CD button), and press the
MACRO MODE button. Then release the buttons.
When you press the MODE CD button, the SEND/LEARN indi-
cator lights up. When you press the MACRO MODE button, the
indicator turns off.
When you release the buttons, the indicator flashes briefly, then
lights up again.
1, 2
2
1, 3
2. Press the operation buttons in series you wish to program
into the MACRO MODE button.
Press the MODE AUDIO, POWER ON, CD (INPUT SELEC-
TOR), MODE CD buttons, and a numeric button. When you
press the button, the SEND/LEARN indicator turns off. When
you release the button, the indicator lights up.
3. Press the MACRO MODE button to complete program-
ming.
The SEND/LEARN indicator flashes twice slowly.
Repeat Steps 1–3 to program other series of button operations
into another MODE button.
4. Check to see if the series of button operation has been cor-
rectly learned.
Point the remote controller toward the receiver, press the
MODE CD button, and press the MACRO MODE button to see
if the unit responds as programmed.
Transmitting the codes in Macro mode takes a while. During
transmission, point the remote controller toward the device to be
controlled.
2
2
Notes:
•
You may program up to 16 button operations into each MACRO button.
If you try to program the 17th step, it will be ignored.
•
If you do not press any button for more than 30 seconds during the pro-
cedure, the SEND/LEARN indicator flashes three times quickly, then
the RC-392M exits Learning mode. Resume from Step 1.
If you make a mistake during programming, the SEND/LEARN indica-
tor flashes three times quickly, then the RC-392M exits Learning mode.
Resume from Step 1.
If you cancel one of the operation already programmed in the MACRO
MODE button, or if you program a different code into such a button, the
operation button will no longer work. In this case, program the buttons
again to avoid malfunction.
•
•
Tip:
The codes programmed into a MACRO button
will be transmitted with an interval of 0.5 sec-
onds. However, some devices may not be able
to complete one operation in 0.5 seconds and
may miss the next code. In this case, press one
operation button, press the corresponding
MODE button, then press another operation
button to extend the interval between the two
operations up to one second.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Macro function
Macro Direct Learning function
A series of remote controller button operations can be memorized
into the MACRO DIRECT button for one-touch control.
Note:
You can program only one series of button operations into the
MACRO DIRECT button.
1. Press and hold down any one of the eight MODE buttons
and press the MACRO DIRECT button. Then, release the
buttons.
1, 3
1
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the MACRO DIRECT button, the
indicator turns off. When you release the buttons, the indicator
flashes briefly, then lights up again.
2. Follow Step 2 in the “Programming Macro Mode” on page
54.
3. Press the MACRO DIRECT button to complete the proce-
dure.
The SEND/LEARN indicator flashes twice slowly.
4. Check to see if the button has been programmed correctly.
Point the RC-392M toward the receiver and press the MACRO
DIRECT button, and make sure that the device responds as pro-
grammed.
Transmitting the codes in Macro mode takes a while. During
transmission, point the remote controller toward the device to be
controlled.
Notes:
•
You may program up to 16 button operations into the MACRO DI-
RECT button. If you try to program the 17th step, it will be ignored.
If you do not press any button for more than 30 seconds during the pro-
cedure, the SEND/LEARN indicator flashes three times quickly, then
the RC-392M exits Learning mode. Resume from Step 1.
If you make a mistake during programming, the SEND/LEARN indica-
tor flashes three times quickly, then the RC-392M exits Learning mode.
Resume from Step 1.
If you cancel one of the operation already programmed in the MACRO
DIRECT button, or if you program a different code into such a button,
the operation button will no longer work. In this case, program the but-
tons again to avoid malfunction.
•
•
•
Tip:
The codes programmed into a MACRO
button will be transmitted with an interval
of 0.5 seconds. However, some devices
may not be able to complete one operation
in 0.5 seconds and may miss the next
code. In this case, press one operation
button, press the corresponding MODE
button, then press another operation but-
ton to extend the interval between the two
operations up to one second.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Macro function
Erasing a learned remote controller button
operation from the MACRO MODE buttons
1. Press and hold down the corresponding MODE button and
press the MACRO MODE button, then release the buttons.
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the MACRO MODE button, the
indicator turns off. When you release the buttons, the indicator
flashes once.
2. Press the MACRO MODE button again.
The SEND/LEARN indicator flashes twice slowly. The learned
operation is erased.
1, 2
1
Erasing a learned remote controller button
operation from the MACRO DIRECT button
1. Press and hold down any one of the MODE buttons and
press the MACRO DIRECT button. Then release the but-
tons.
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the MACRO DIRECT button, the
indicator turns off. When you release the buttons, the indicator
flashes once.
1, 2
1
2. Press the MACRO DIRECT button again.
The SEND/LEARN indicator flashes twice slowly. The learned
operation is erased.
Notes:
•
If you do not press any button for more than 30 seconds, the SEND/
LEARN indicator flashes three times quickly, then the RC-392M exits
Learning mode. Resume from Step 1.
•
If you press a wrong button in Step 2, you may have overwritten the
memory of the button you pressed.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Macro function
Erasing all codes and operations programmed in
the buttons
This procedure will erase all remote controller codes for the other
devices and all macro operations that have been programmed in the
RC-392M (see pages 52, 54 and 55).
1. Open the battery cover and remove the batteries.
2. While pressing and holding down the POWER ON button
and the POWER STNBY button, insert the batteries in the
correct direction.
2
After inserting the batteries, release the buttons. The SEND/
LEARN indicator flashes slowly.
3. Press the ENT button.
The SEND/LEARN indicator lights up for about ten seconds,
then turns off.
All programmed codes are erased and the button memories re-
turn to the factory presets.
Notes:
•
Proceed to Step 3 immediately once you have completed Step 2. Other-
wise, the batteries will be consumed quickly.
•
If you press any button other than the ENT button in Step 3, no codes
will be erased. In this case, repeat the steps from the beginning.
3
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
If a problem occurs while you are using the remote controller, first try to operate the front panel controls on the main unit to make sure that
it is not due to a malfunction (or worn out batteries) in the remote controller.
Trouble
Cause
Remedy
See
page
POWER
Power shut off immedi-
ately after power on.
No power.
• Amplifier protection circuitry has been acti-
vated.
•
Remove the AC plug from the outlet immediately.
Then contact your Onkyo service center.
Connect power cord.
-
• Power cord is disconnected.
• There is external noise in the computer circuits
of this unit.
•
•
13
13
Turn the power button off and then on again or remove
the AC plug from the outlet and then plug it again.
Contact your Onkyo Service Center.
Press the MUTING button on the remote controller to
turn it off.
• AC fuse blown.
•
•
-
Power on but no sound.
• “Muting” is displayed.
31
• The digital/analog input setting is incorrect.
• Bad connections.
•
•
•
Select the correct input.
23,29
6-15
-
Check connections, speaker leads, etc.
Contact your Onkyo Service Center.
• Amplifier protection circuitry has been acti-
vated.
The sound of the play-
back source is not heard.
No picture appears on
the TV screen (or moni-
tor)
• The input selector is not set properly.
•
•
Set it to the playback source.
26,27
8
• The TV (or monitor) is not set to receive the out-
put signals from the reciver.
Set the TV (or monitor) to the receiver input.
• The video cable is not connected securely.
• Only S video connection is made.
•
•
Check the connections.
8
8
Make also video connection.
SPEAKERS
No sound from the cen-
ter speaker, or very
minimal sound.
• Speaker cable is not connected.
•
•
Check the connection between the amplifier and the
speaker.
11
• Listening mode is set to Stereo or Direct.
Set the Listening mode to any mode other than Stereo
or Direct.
34-38
• CENTER level is set to minimum.
• CENTER SPEAKER is set to None.
• Subwoofer is set to No.
•
•
•
•
Set the CENTER level to the appropriate volume.
Set CENTER SPEAKER to Large or Small.
Check the speaker setting.
21
18,19
12
No sound or quiet sound
from subwoofer
• Subwoofer speakers output level setting is im-
proper.
Check the output level of the Subwoofer using the test
tone.
22
PHONO
Hum, low-frequency noise.
• Poor or no input ground.
•
•
•
Check outer conductor of input plugs.
Check for proper ground connection.
6
6
-
• Poor or no phono motor ground.
• The placement of the audio connection cables
on the rear panel is incorrect.
Adjust the placement of the cable to reduce hum.
Howling when the vol-
ume is turned up.
• Turntable and speakers are too close together.
•
Move them farther apart.
-
Rough or scratchy
sound. High range is not
clear.
• Stylus of turntable pick-up is worn.
• Turntable stylus tip is dirty.
• Treble control too high.
•
•
•
Replace.
-
-
Clean.
Turn treble control down.
31
FM/AM
AM stations cannot be
received.
• AM loop antenna is not attached.
•
Connect the included AM loop antenna to the AM an-
tenna terminals.
14
Buzzing noise on AM
(particularly conspicu-
ous at night or with
weak stations).
• Noise from electrical apparatus such as fluores-
cent lamp.
•
•
Move the AM loop antenna to different position.
Set up an outdoor AM antenna.
15
15
High-pitched noise or
buzzing noise on AM.
• Noise from TV set.
•
Place the AM loop antenna as far as possible from the
15
TV.
•
•
Move unit away from TV set.
-
Crackling noise on AM,
FM.
• Noise caused by turning fluorescent lamp on
and off.
Move antenna as far as possible from the fluorescent
15
lamp.
• Noise from automobile ignition.
•
•
Install an FM outdoor antenna as far as possible from
15
15
the road.
Change the position or direction of the outdoor an-
tenna.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
Trouble
FM/AM
Cause
Remedy
See
page
TUNED and STEREO
indicators light but
sound is distorted and
stereo separation is bad.
TUNED and STEREO
indicators flicker and
hiss is heard on FM.
• Station is too strong.
•
•
Change to FM indoor antenna.
15
15
• Multiple reflection of the radio waves because
of tall buildings or mountains.
Use antenna which has better directivity and select a
point where the distortion is least.
• Station is too weak.
•
•
Install an outdoor FM antenna.
15
15
• Stereo FM broadcasts cover only about half the
distance of an ordinary broadcast.
• The power cord has been unplugged or the
POWER switch has been turned off for a long
time.
Change the position or direction of the outdoor an-
tenna.
No station is recalled.
•
The memory contents are lost. Store all stations again.
25
Video & audio
Desired picture does
• Wrong connection.
•
•
Check the connection again. Insert the plugs and con-
nectors completely.
9
not
appear
when
MULTI CH INPUT but-
ton is pressed.
• No video input is assigned.
Assign a proper video input.
33
No on-screen display.
• Improper connection.
•
•
•
•
•
Check connections.
8
8,9
8
• Improper OSD selector setting.
• Improper connection.
Set the OSD selector properly.
Check connections.
Picture and sound do not
match.
• Improper video is assigned.
• The digital input selector is not set properly.
Check Video Assign setting.
Check Digital Input setting.
40
No sound, or sound of
the selected source is
not heard.
23,29
No picture appears on
the TV screen (or moni-
tor).
• The TV (or monitor) is not set to receive the out-
put signals from the receiver.
•
Set the TV (or monitor) to the receiver input.
-
• The video cable is not connected securely.
• Only S-Video connection is made.
•
•
Check connections.
8
8
Make also video connection.
Others
LATE NIGHT function
cannot be used.
• Playback source is not Dolby Digital encoded.
•
•
•
•
Check that the DOLBY DIGITAL indicator lights up
on the display.
38
38
38
38
LFE LEVEL function
cannot be used.
• Playback source is not Dolby Digital , DTS
encoded.
Check that the DOLBY DIGITAL, DTS indicator
lights up on the display.
Cinema Re-EQ function
cannot be used.
• The listening mode is set to “Stereo,”
“5ch stereo” or “Direct.”
See the table on page 38.
Parameter cannot be set
for Front Effect, Reflect
Level, Reverb Level,
Room Size, etc.
• Parameter may not be set depending on the lis-
tening mode.
See the table on page 38.
Front panel controls
function but remote
controller does not.
• No batteries in remote controller.
• Batteries have worn out.
•
•
•
Insert batteries.
5
5
5
Replace batteries.
• The remote controller is not pointed at the re-
mote sensor of the receiver.
Point the remote controller at the remote sensor of the
reciever.
• The remote controller is too far from the
reciever.
•
Operate the remote controller within 16 feet (5m).
5
Also refer to the respective instruction manuals of the video disc player, video cassette recorder, TV monitor, etc., that compose your
entertainment system.
Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If this
happens, press the POWER switch on the unit and then press it again after about five seconds.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
DTR-7
DTR-6
AMPLIFIER SECTION
AMPLIFIER SECTION
Continuous Average Power output (FTC)
Continuous Average Power output (FTC)
All channels:
105 watts per channel min. RMS at 8
All channels:
85 watts per channel min. RMS at 8
ohms, 2 channels driven from 20 Hz
to 20 kHz with no more than 0.08%
total harmonic distortion.
ohms, 2 channels driven from 20 Hz
to 20 kHz with no more than 0.08%
total harmonic distortion.
135 watts min. RMS at 6 ohms, 2
channels driven from 1 kHz with no
more than 0.1% total harmonic dis-
tortion.
110 watts min. RMS at 6 ohms, 2
channels driven from 1 kHz with no
more than 0.1% total harmonic dis-
tortion.
Total Harmonic Distortion:
IM Distortion:
Damping Factor:
0.08% at rated power (Front)
0.08% at rated power (Front)
60 at 8 ohms (Front)
Total Harmonic Distortion:
IM Distortion:
Damping Factor:
0.08% at rated power (Front)
0.08% at rated power (Front)
60 at 8 ohms (Front)
Input Sensitivity and Impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1, 2, 3,4):
Input Sensitivity and Impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1, 2, 3,4):
2.5 mV, 50 kohms
200 mV, 50 kohms
2.5 mV, 50 kohms
200 mV, 50 kohms
MULTICHANNEL INPUT
MULTICHANNEL INPUT
(FRONT L/R, SURROUND L/R, CENTER):
200 mV, 50 kohms
(FRONT L/R, SURROUND L/R, CENTER):
200 mV, 50 kohms
(SUBWOOFER):
COAXIAL 1, 2 (DIGITAL):
Output Level and Impedance
Rec out (TAPE, VIDEO 1):
Pre out:
36 mV, 50 kohms
0.5 Vp-p, 75 ohms
(SUBWOOFER):
COAXIAL 1, 2 (DIGITAL):
Output Level and Impedance
Rec out (TAPE, VIDEO 1):
Pre out:
36 mV, 50 kohms
0.5 Vp-p, 75 ohms
200 mV, 2.2 kohms
1 V, 470 ohms
200 mV, 2.2 kohms
1 V, 470 ohms
Phono Overload:
Frequency Response:
RIAA Deviation:
Tone Control
110 mV RMS at 1 kHz, 0.5% T.H.D.
20 Hz to 100 kHz, +1/-3 dB(LINE INPUT)
20 Hz to 20 kHz, ±0.8 dB
Phono Overload:
Frequency Response:
RIAA Deviation:
Tone Control
110 mV RMS at 1 kHz, 0.5% T.H.D.
20 Hz to 100 kHz, +1/-3 dB(LINE INPUT)
20 Hz to 20 kHz, ±0.8 dB
Bass:
Treble:
±10 dB at 100 Hz
±10 dB at 10 kHz
Bass:
Treble:
±10 dB at 100 Hz
±10 dB at 10 kHz
Signal-to-Noise Ratio
Phono:
CD/Tape:
Signal-to-Noise Ratio
Phono:
CD/Tape:
80 dB (IHF A, 5 mV input)
100 dB (IHF A)
80 dB (IHF A, 5 mV input)
100 dB (IHF A)
VIDEO SECTION
VIDEO SECTION
Input sensitivity/Impedance
(DVD, VIDEO 1, 2, 3,4)
VIDEO (Composite):
Output Level/Impedance
(VIDEO 1, 2, MONITOR)
VIDEO (Composite):
Input sensitivity/Impedance
(DVD, VIDEO 1, 2, 3,4)
VIDEO (Composite):
Output Level/Impedance
(VIDEO 1, 2, MONITOR)
VIDEO (Composite):
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
DTR-7
DTR-6
TUNER SECTION
FM
TUNER SECTION
FM
Tuning Range:
Usable Sensitivity
Mono:
87.5 - 108.0 MHz (50 kHz steps)
Tuning Range:
Usable Sensitivity
Mono:
87.5 - 108.0 MHz (50 kHz steps)
11.2 dBf, 1.0 µV (75 ohms IHF)
17.2 dBf, 2.0 µV (75 ohms IHF)
11.2 dBf, 1.0 µV (75 ohms IHF)
17.2 dBf, 2.0 µV (75 ohms IHF)
Stereo:
Stereo:
50 dB Quieting Sensitivity
Mono:
Stereo:
Capture Ratio:
Image Rejection Ratio
50 dB Quieting Sensitivity
Mono:
Stereo:
Capture Ratio:
Image Rejection Ratio
17.2 dBf, 2.0 µV (75 ohms)
37.2 dBf, 20 µV (75 ohms)
2.0 dB
17.2 dBf, 2.0 µV (75 ohms)
37.2 dBf, 20 µV (75 ohms)
2.0 dB
40 dB
40 dB
IF Rejection Ratio:
Signal-to-Noise Ratio
Mono:
90 dB
IF Rejection Ratio:
Signal-to-Noise Ratio
Mono:
90 dB
76 dB
70 dB
55 dB
50 dB
76 dB
70 dB
55 dB
50 dB
Stereo:
Stereo:
Alternate Channel Attenuation:
AM Suppression Ratio:
Total Harmonic Distortion
Mono:
Alternate Channel Attenuation:
AM Suppression Ratio:
Total Harmonic Distortion
Mono:
0.2%
0.2%
Stereo:
0.3%
Stereo:
0.3%
Frequency Response:
Stereo Separation:
30 Hz - 15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz - 10 kHz
Frequency Response:
Stereo Separation:
30 Hz - 15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz — 10 kHz
AM
AM
Tuning Range
530 - 1,710 kHz (10 kHz steps)
Tuning Range
530 - 1,710 kHz (10 kHz steps)
Usable Sensitivity:
Image Rejection Ratio:
IF Rejection Ratio:
Signal-to-Noise Ratio:
Total Harmonic Distortion:
30 µV
40 dB
40 dB
40 dB
0.7%
Usable Sensitivity:
Image Rejection Ratio:
IF Rejection Ratio:
Signal-to-Noise Ratio:
Total Harmonic Distortion:
30 µV
40 dB
40 dB
40 dB
0.7%
GENERAL
GENERAL
Power Supply:
Power Consumption:
Dimensions (W × H × D):
AC 120 V, 60 Hz
6.2A
435 × 175 × 453 mm
17-1/8" × 6-7/8" × 17-13/16"
16.3 kg, 35.9 lbs.
Power Supply:
Power Consumption:
Dimensions (W × H × D):
AC 120 V, 60 Hz
5.3A
435 × 175 × 453 mm
17-1/8" × 6-7/8" × 17-13/16"
14.7 kg, 32.4 lbs.
Weight:
Weight:
REMOTE CONTROL
Transmitter:
REMOTE CONTROL
Transmitter:
Infrared
Infrared
Signal range:
Power supply:
Approx. 5 meters, 16 ft.
Two “AA” batteries (1.5 V × 2)
Signal range:
Power supply:
Approx. 5 meters, 16 ft.
Two “AA” batteries (1.5 V × 2)
Specifications and features are subject to change without notice.
Specifications and features are subject to change without notice.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Control positions and names
The illustration shows the front panel of the DTR-7 model. The ap-
pearance of the front panel varies depending on the model you pur-
chased.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
17
MASTER VOLUME
FM MUTE/
MODE
CHARACTER/
MEMORY
SP/SYS
SETUP
AUDIO
ADJUSTMENT
BASS/
TREBLE
DIMMER
DOWN TUNING
UP
STANDBY/ON
MODE
PRESET/MODE ADJ
STANDBY MULTI SOURCE
POWER
SMART SCAN
CONTROLLER
PUSH TO ENTER
DIGITAL/
ON
OFF
LISTENING MODE
REC OUT/
A
SPEAKERS
PHONES
B
DISPLAY
DIRECT
STEREO
/DTS
THX
DSP
MULTI SOURCE
CH LEVEL
ANALOG
SURROUND
MODE
VIDEO4 (MONO)
MULTI CH INPUT
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
TAPE
FM
AM
PHONO
CD
S
VIDEO
VIDEO
L
AUDIIOO
R
DTR-
7
by
25
24
23
22
21 20
19
j
18
a
b
c
d
e
f
g
h
SPEAKERS REC OUT SLEEP
DOLBY DIGITAL
PCM DIGITAL
DTS
DOLBY PRO LOGIC
DSP STEREO
DIRECT
TUNED
A
B
MULTI SOURCE
MEMORY FM STEREO AUTO
ft
ch
dB
k
j
2 4 . PHONES [26]
25. MULTI SOURCE indicator [47]
Front panel
For more information about buttons or knobs, refer to the pages
listed in the brackets ( [ ] ) below.
1. STANDBY indicator [5, 13]
Display
2. STANDBY/ON button[13]
3. POWER switch [13]
4. SPEAKERS A/B button [26, 30]
5. DISPLAY button [23, 30, 47]
If a protective film on the surface of the screen making it difficult to
read the display, remove the film.
a. Speakers A/B indicators
b. Rec out indicator
c. Sleep indicator
6. DIMMER button [26]
7. Display (Refer to the “Display” illustration.)
8. LISTENING MODE buttons [35, 36, 38]
9. FM MUTE/MODE button [24]
10. TUNING UP/DOWN button [23]
11. Remote control sensor [5]
d. PCM digital indicator
e. Listening mode or Digital input format indicators
f. Memory indicator
g. FM Stereo indicator
h. Tuned indicators
12. CHARACTER/MEMORY buttons [25, 41]
13. SP/SYS SETUP button [16, 18, 20~22, 40, 43 ]
14. AUDIO ADJUSTMENT button [38]
15. BASS/TREBLE button [31]
16. SMART SCAN CONTROLLER [16, 32]
17. MASTER VOLUME control knob [26, 35]
18. VIDEO-4/VIDEO CAM INPUT [8]
19. CH LEVEL button [42]
i. Auto indicator
j. Multi function display
(Frequency and Preset station/Input selector/Sleep time/
Volume level/Listening mode)
k. MULTI SOURCE indicator
20. DIGITAL/ANALOG button [23, 28]
2 1 . REC OUT/MULTI SOURCE button [44~47]
22. INPUT SELECTOR buttons [23, 26, 32, 35]
23. MULTI CHANNEL INPUT button [33]
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Control positions and names
Remote controller
Using the remote controller, you can control a CD player or cas-
sette tape deck connected to the connector of the DTR-7/6.
(See page 7 for more information.)
1. SEND/LEARN indicator [49, 52, 53]
2. POWER ON/STNBY button [13, 49, 50, 54, 57]
Power on/Standby on
1
3. SLEEP button [27, 31, 49]
Sleep function button
4. MACRO DIRECT button [55, 56]
Macro Direct function
5. MODE buttons [13, 27, 49~56]
6. DISPLAY/DVD SET button [49, 50]
7. CH +/– buttons [32, 49]
2
3
22
21
4
8. EXIT/RETURN button [16, 17, 50]
9. PREV CH button
[This button is not used for this receiver.]
10. TRACK button [50]
11. CD/TAPE/DVD/MD operation buttons [50, 51]
12. Input Selector buttons [27, 32, 35, 49]
13. Numeric key/STEREO/DSPa, s/SURROUND/SPA,
B/CH SEL/LEVEL+,–/DIMMER buttons [21, 27, 33, 35, 42,
49~51]
[The THX button are not used for the DTR-6.]
14. ENT button [50~53, 57]
15. DISC button [50]
16. MUTING button [31, 32, 49, 50]
17. TEST/TV/VCR button [49]
5
6
20
19
18
7
8
17
16
15
9
10
18. ENTER/cursor buttons [16, 17, 50]
19. VOL ∆/∆ button [27, 35, 49, 50]
Volume adjustment
20. OSD/MENU button [16, 17, 50]
21. MACRO MODE button [54, 56]
22. LIGHT button [49]
11
12
13
14
63
Download from Www.Somanuals.com. All Manuals Search And Download.
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
SN 29342732
Printed in Japan
D9907-1
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|