Operating Instructions
FRIDGE
Contents
GB
Installation, 2-3
Positioning and connection
Reversible doors
GB
English,1
Description of the appliance, 5
Overall view
Accessories, 6
Start-up and use, 7-8
Starting the appliance
Chiller system
Using the refrigerator to its full potential
Food hygiene
Maintenance and care, 9
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Defrosting the appliance
SAN 300
SAAN 300
SAN 400
Replacing the light bulb
SAN 400 S
Precautions and tips, 10
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 11
Assistance, 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting a new plug
Reversible doors
GB
IMPORTANT
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
1
Blue
Brown
- Neutral
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
-
Connect Green and Yellow wire to terminal marked
'E' or or coloured Green and Yellow.
Connect Brown wire to terminal marked 'L' or
coloured red or brown.
Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
2
3
-
-
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
4
5
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Stability bracket
(Models SAN400 and SAN400S only):
Position the fridge in its chosen location.
Looking from the front of the fridge, mark the position
of the left hand panel.
GB
Move the fridge far enough away to get clear access
to the back wall.
In order to clear components on the compressor
mounting plate, the stability bracket must be
positioned on the floor between 100 - 200mm to the
right of the left hand panel mark.
WARNING: To prevent the fridge from tilting forwards, it
must be held in place with the stability bracket supplied.
This is the responsibility of the customer.
Mark and drill the fixing holes and insert suitable
fixings to hold the bracket firm.
Carefully re-position the fridge. Make sure that the
compressor mounting plate locates into the stability
bracket.
Fixed to the floor or wall at the rear of the fridge, the
stability bracket hooks onto the compressor mounting
plate holding the fridge secure.
The stability bracket must be installed securely in
accordance with these instructions BEFORE using
the fridge.
Position stability bracket
100 - 200mm away from left
hand panel mark.
Note: The fridge is heavy so care must be taken when
moving it.
Position of left
hand panel
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the
appliance
Overall view
GB
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased. For more complex features, consult the following pages.
TEMPERATURE control
Removable lidded
shelf with EGG TRAY
Lamp
(see Maintenance)
Removable
multipurpose
SHELVES
SHELVES•
BOTTLE shelf
MULTI-USE bin
*
FRUIT and
VEGETABLE bin
Levelling FEET
• Varies by number and/or position.
Available only on certain models.
*
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
SHELVES: with or without grill.
Play Zone Thanks to the new “Play Zone” bottle rack,
you can cool several bottles, cans and energy drinks
quickly to have them constantly at hand.
*
GB
Due to the special guides the
shelves are removable and the
height is adjustable (see
diagram), allowing easy storage
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
1
2
MULTI-USE bin: to store food (such as cold meats) for
*
a long time and also prevent odours from lingering in
the refrigerator.
If the “Play Zone” is placed on the glass shelf, you can
store large and medium sized bottles on it simply by
laying the bottle on the flat rack. This is ideal for storing
wine bottles. When folded and secured in place on either
side of the shelf, the rack can be used to store cans (at
the top), energy drinks (in the centre) and other cans
and energy drinks can be rested horizontally on the
remaining part of the shelf. When placing cans (onto the
Play zone rack), make sure they do not touch the back
of the refrigerator interior.
The “Play Zone” can be used just like a normal shelf
(when placed flat) and moved up or down along the
fridge walls together with the rest of the shelf. It can be
washed easily, and is also dishwasher safe. The ideal
position for the Play zone rack is the central shelf.
TEMPERATURE Indicator light: to identify the coldest
area in the refrigerator.
1. Check that OK appears clearly on the indicator light
(see diagram).
*
vert
noir consulter la notice
2. If the word “OK” does not appear it means that the
temperature is too high: adjust the REFRIGERATOR
OPERATION knob to a higher position (colder) and
wait approximately 10 hours until the temperature has
been stabilised.
3. Check the indicator light again: if necessary, readjust
it following the initial process. If large quantities of
food have been added or if the refrigerator door has
been opened frequently, it is normal for the indicator
not to show OK. Wait at least 10 hours before
adjusting the REFRIGERATOR OPERATION knob to a
higher setting.
Available only on certain models.
*
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
Starting the appliance
The Aircooler maintains a constant fridge temperature to
keep food fresher for longer and will quickly restore the
temperature to the correct level, even if the door is
opened frequently: the blown air (A) is cooled when it
comes into contact with the cold wall, whereas the hotter
air (B) is sucked up (see diagram).
The back wall may be covered in frost or droplets of
water, depending on whether the compressor is in
operation or whether it is paused.
GB
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the
compartments and accessories well with lukewarm
water and bicarbonate.
1. Insert the plug into the socket and ensure that the
internal light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an
average value. After a few hours you will be able to
put food in the refrigerator.
Static
Models without the Aircooler. have the cooling section in
the internal back wall of the compartments. The wall will
be covered in frost or water droplets depending on
whether the compressor is operating or paused: both
cases are normal. If the TEMPERATURE ADJUSTMENT
knob has been set on high values with large quantities
of food and with a high ambient temperature, the
appliance can operate continuously, resulting in
excessive frost formation and excessive energy
consumption: compensate for this by shifting the knob
towards lower values (defrosting will occur
automatically).
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself according to the position of
the thermostat knob.
= warmest
= coldest
In static appliances, the air circulates in a natural way:
the colder air tends to move downwards as it is heavier.
The food should be stored as follows:
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside
the back wall of the refrigerator compartment for
increased space and improved aesthetics. During
operation, the back wall will be covered in frost or water
droplets depending on whether the compressor is
operating or paused. Do not worry, the refrigerator is
functioning normally.
$UUDQJHPHQWꢀLQVLGHꢀWKHꢀ
UHIULJHUDWRUꢀ
Above the fruit and vegetable
bins
)RRGꢀ
Fresh fish and meat
Above the fruit and vegetable
Fresh cheese
bins
Cooked food
On any shelf
Salami, bread loaf,
chocolate
On any shelf
Chiller system
Fruit and vegetables In the fruit and vegetable bins
Eggs On the shelf provided
Butter and margarine On the shelf provided
Bottles, drinks, milk On the shelf provided
The appliance comes with one of the chiller systems
described below: take note of your system in order to
determine the most efficient food storage method.
Aircooler
It is recognizable due to the presence of the mechanism
on the top part of the refrigerator compartment (see
diagram).
B
A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the refrigerator to its full potential
GB
• Use the TEMPERATURE ADJUSTMENT knob to adjust
the temperature (see Description).
• Place only cold or lukewarm foods in the
compartment, not hot foods (see Precautions and
tips).
• Remember that cooked foods do not last longer than
raw foods.
• Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Food hygiene
1. Once you have bought your food, remove all external
packaging made of paper/cardboard or other
wrappers, which could introduce bacteria or dirt
inside your refrigerator.
2. Protect the food, (especially easily perishable items
and those that have a strong smell), in order to avoid
contact between them, thereby removing both the
possibility of germ/bacteria contamination as well as
the diffusion of strong odours inside the fridge.
3. Store all food in such a way as to ensure air can
circulate freely between different items.
4. Keep the inside of your fridge clean, taking care not
to use oxidiser or abrasive products.
5. Remove all food past its expiry date from the
refrigerator.
6. For the correct preservation of food, all easily
perishable items (soft cheeses, raw fish, meat, etc.)
should be stored in the coldest zone of the fridge
compartment, i.e. just above the salad crisper where
the temperature indicator is situated.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Switching the appliance off
Defrosting the appliance
GB
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
It is not sufficient to set the temperature adjustment
knobs on (appliance off) to eliminate all electrical
contact.
! Follow the instructions below.
Do not speed up the defrosting process by using any
tools or electrical devices, you may damage the
refrigeration circuit.
The refrigerator has an
automatic defrosting
function: water is ducted
to the back of the
Cleaning the appliance
• The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
appliance by a special
discharge outlet (see
diagram) where the heat
produced by the
compressor causes it to
evaporate. It is necessary
to clean the discharge
hole regularly so that the water can flow out easily.
• The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
• The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
Replacing the light bulb
To replace the light bulb in the refrigerator compartment,
pull out the plug from the electrical socket. Follow the
instructions below.
Avoiding mould and unpleasant odours
Access the light bulb by removing the cover as
indicated in the diagram.
Replace it with a similar light bulb within the power
range indicated on the cover (15W or 25W).
• The appliance is manufactured with hygienic
materials which are odour free. In order to maintain an
odour free refrigerator and to prevent the formation of
stains, food must always be covered or sealed
properly.
• If you want to switch the appliance off for an extended
period of time, clean the inside and leave the door
open.
1
1
2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
Disposal
GB
• Observe local environmental standards when
disposing packaging material for recycling purposes.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE..
General safety
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
Respecting and conserving the
environment
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
• Do not touch the appliance with bare feet or with wet or
moist hands and feet.
• Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
• WARNING: do not damage the refrigerant circuit.
• Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
• Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It
is not sufficient to set the temperature adjustment knobs
on (appliance off) to eliminate all electrical contact.
• Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
• In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
• Defrost the appliance if ice forms (see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
• WARNING: do not use electrical or machanical devices
or tools other than the special scraper provided inside
the compartments.
• Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (see Maintenance).
• Do not put ice cubes taken directly from the freezer into
your mouth.
• Do not allow children to tamper with the controls or play
with the appliance. Under no circumstance should they
be allowed to sit on the bins or to hang from the door.
• Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
GB
Malfunctions:
Possible causes / Solutions:
The internal light does not
illuminate.
• The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
The refrigerator do not cool well.
• The door do not close properly or the seals are damaged.
• The door are opened too frequently.
• The TEMPERATURE ADJUSTMENT knob is not in the correct position
• The refrigerator have been over-filled.
The food inside the refrigerator is
beginning to freeze.
• The TEMPERATURE ADJUSTMENT knob is not in the correct position.
• The food is in contact with the back inside wall of the refrigerator.
The AIR fan does not rotate.
• The refrigerator door is open.
• The AIR system is only activated automatically when it becomes
necessary to restore perfect operational conditions inside the refrigerator
compartment.
The motor runs continuously.
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
The appliance makes a lot of noise.
• The appliance has not been installed on a level surface (see Installation).
• The appliance has been installed between cabinets that vibrate and
make noise.
• The internal refrigerant makes a slight noise even when the compressor is
off. This is not a defect, it is normal.
The back wall of the refrigerator unit
is covered in frost or droplets of
water
• This shows the appliance is operating normally.
There is water at the bottom of the
refrigerator.
• The water discharge hole is blocked (see Maintenance).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assistance
195051290.00
Before calling for Assistance:
• Check if the malfunction can be solved on your own (see Troubleshooting).
GB
• If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service
Centre
model
serial number
Communicating:
• type of malfunction
• appliance model (Mod.)
• serial number (S/N)
This information can be found on the data
plate located on the bottom left side of the
refrigerator compartment.
TI
93139180000
Cod.
S/N 704211801
Mod. RG 2330
220 - 240 V-
Fuse
A
Max 15 w
50 Hz 150 W
W
Class
Freez. Capac
340
75
Total
Net
Gross
Bruto
Brut
Gross
Bruto
Brut
Gross
Bruto
Brut
Poder de Cong Clase
N
Util
Classe
kg/24 h 4,0
Utile
Pressure
HIGH-235
LOW 140
Compr.
Syst.
Test
R
134 a
P.S-I.
kg 0,090
Kompr.
Made in Italy 13918
Never call on unauthorized technicians and always refuse spare parts which are not originals.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|